CD328BT 07042017
Super Bass Boombox
1
Instruction Manual
Model Ref: CD328BT / Cat Number: MM339
Introduction
Thank you for choosing this Super Bass Boombox. This
product is manufactured to the highest standards of
performance and safety.
Before use, please read this manual carefully. It gives
important instructions about safety, use and maintenance of
your device.
Remove all packaging material. You may wish to keep
the packaging for future use or storage of your device.
Alternatively, dispose of accordingly.
01
Important Safety Information
WARNING - To reduce the risk of fire, electric shock, or
injury:
1. This appliance is for domestic use only. Do not use
outdoors or on wet surfaces.
2. Do not handle the plug or appliance with wet hands.
3. Do not immerse the main body in water.
4. This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities, or lack of experience
and knowledge, if they have been given supervision or
instruction concerning the use of the appliance in a safe
way and understand the hazards involved.
5. Children must not play with the appliance.
6. Cleaning and user maintenance shall not be made by
children unless they are older than 8 and supervised.
7. Keep the appliance and its cord out of reach of children
less than 8 years.
8. This product is not a toy.
9. Do not use the appliance if any parts appear to be
faulty, missing or damaged.
10. Always switch off at the mains supply before carrying
out any cleaning, performing user maintenance or
changing accessories.
11. Do not use the appliance if it has been dropped or
damaged in any way.
12. Check to ensure that the electricity supply matches that
shown on the rating plate.
13. Only use the attachments/accessories supplied with the
product or recommended by JDW.
14. If the supply cord is damaged, it must be replaced by a
02
qualified service agent in order to avoid a hazard
15. Only use this appliance for its intended domestic use.
JDW will not accept any liability if the appliance is
subject to improper use, or failure to comply with these
instructions.
16. Keep the appliance and its power supply cord away
from heat or sharp edges that could cause damage.
17. Keep the power supply cord away from any parts of the
appliance that may become hot during use.
18. Do not disconnect the appliance from the mains power
supply by pulling the cord, switch it off and remove the
plug by hand.
19. Do not move the appliance when it is in use.
20. Use of an extension cord with the appliance is not
recommended.
21. This appliance should not be operated by means of an
external timer or separate remote control system.
22. Keep the appliance away from flammable materials.
03
PRODUCT OVERVIEW
04
BOOMBOX CONTROLS
1.
2.
3.
4.
5.
6.
7.
8.
9.
Display
Speaker decoration ring
Left/right speakers
Headphone jack
SD Card slot
USB port
Standby/Pair indicator
AUX in Jack
Passive speaker
decoration ring
10.Volume knob
11.Function button
12.EQ/light button
13.Prog/P-mode button
14.Back/fast backward/-10
button
15.CD door
16.Next/fast forward/+10
button
17.Stop button
18.Play/pair/pause button
19.Standby button
20.Tuning knob
21.Antenna
22.Left/right passive
speakers
23.Handle
24.Battery door
25.AC Socket
REMOTE CONTROL
05
1. Function button
2. Mute button
3. Memory button
4. EQ button
5. Fold/10/M. Up/Down button
6. CD B-Skip down/Tun.- button
7. CD play/pause button
8. P-Mode button
9. Stop/Mo/ST. button
10.Pair button
11.CD f-skip/tun.+ button
12.ID3 button
13.Vol. up/down button
14.Light button
15.Mo/St button
16.Standby button
17.Remote sensor
18.Battery compartment
REMOTE CONTROL OPERATION
To operate the Boombox with
the remote control, point the
remote handset at the remote
sensor on the front panel and
press the appropriate button on
the remote handset.
The remote works best within
a range of 6 ~ 7 meters from
the front panel and on an angle
of 30 degrees. Bright sunlight
or room light conditions can
interfere with the remote control.
If the remote operation is
unsatisfactory or stops working
entirely, first try replacing
the remote batteries, then try reducing the room lighting
conditions.
REMOTE CONTROL OPERATION
• The remote control includes one
CR2025(3V) lithium battery.
• To replace the battery, gently push the
clasp to the right direction accordingly
to the instruction and then pull out the
battery compartment. Take the drained
battery out and install a new lithium
battery(CR-2025) in the compartment with
the positive polarity up-warded. Then push
the compartment back to its position with a
“click” sound indicating installation finished
06
POWER SOURCE
This Boombox is designed to be operated on AC/DC.
AC OPERATION
Plug the tail of supplied AC power cord into AC socket
on Boombox and the plug into household AC outlet. The
batteries will be automatically disconnected. This Boombox
is designed in Switched-Mode Power Source with voltage
range from 100V to 240V.
DC OPERATION
Open the BATTERY COMPARTMENT DOOR. Install 8pcs
UM-1/D size batteries (not included) into compartment.
Please follow correct polarities as indicated.
NOTE: when using battery, take off the AC cable from
Boombox.
CAUTION:
Remove batteries if they are flat or not being used for a long
period of time. Batteries contain chemical substances, so
they should be disposed of properly.
07
USING THE BOOMBOX
SWITCHING ON THE Boombox
After connecting the power, press the STANDBY button
on the Boombox or on the remote control to turn on the
Boombox. Press the FUNC. button on Boombox or on the
remote control to choose TUNER / CD / USB / AUX /SD
CARD or BLUETOOTH function.
NOTE: In CD/MP3/USB/SD/AUX/BT mode when the
Boombox is not providing the main function for 15 minutes,
the Boombox will automatically switch into standby mode.
To turn on the Boombox again, press “STANDBY” button or
replug the Boombox.
ESD hints – The product maybe reset or not reset to
operation of control due to electrostatic discharge, just switch
off and reconnect again.
VOLUME ADJUSTING
Rotate the VOLUME button on Boombox or on the remote
control to increase or decrease volume.
EQ FUNCTION
This Boombox has a built-in equalizer system, Press EQ/
LIGHT button on Boombox or EQ key on the remote control
while playing to select different music style (sound tone):
FLAT, CLASSIC, ROCK, POP and JAZZ.
HEADPHONE JACK
For private listening, insert a 3.5mm headphone (not
included) into the HEADPHONE jack (4). The SPEAKER
output would be automatically cut off.
CAUTION: LISTENING AT A HIGH VOLUME OVER A
LONG PERIOD IS NOT GOOD FOR YOUR EARS.
08
DISCO LIGHT
There are eight flashing modes of the disco light, press and
hold the EQ/LIGHT button on Boombox or press the LIGHT
KEY on the remote control to choose the desired mode. To
turn off the disco light, press and hold the EQ/LIGHT button
on Boombox or press the LIGHT KEY on the remote control
until “LIGHT OFF” shows on the display.
RADIO OPERATION
TUNING RADIO STATIONS
1. Press the FUNC. button on Boombox or on the remote
control to select the TUNER FUNCTION, this Boombox is
designed for FM ONLY.
2. Tune to desired station by rotating the TUNING knob on
Boombox or by pressing TUN+ / Fast Forward, TUN- /
Fast Backwards key on the remote control, the display will
show the band frequency. Example: FM 97.10 MHz. If the
radio is receiving Stereo signal, “STEREO” will show on
the display.
3. Extend FM TELESCOPIC ANTENNA to its full length and
gently move the Boombox back and forth to get the best
reception, or place the Boombox in an open location.
4. To turn off the radio, press the FUNC. Button on Boombox
or on the remote control to switch to other functions or
press STANDBY button on Boombox or on the remote
control to turn off the Boombox
RADIO AUTO SCAN (SEARCH)
Press the / PAIR button on Boombox or
key on the
remote control, the Boombox will conduct auto scan and
program until having found a strong signal. The Boombox will
start to broadcast the P01 after searching finished.
Press the Fast Forward / +10 button on Boombox or FOLD.
/ 10/M UP/DOWN key on the remote control to choose next
09
programmed
station.
RADIO STATION MEMORY OPERATION
You may pre-store 30 (FM) radio stations in memory for
your preference, so as you can listen to your desired station
directly and quickly, no need to tuning and search for again.
1. Press PROG./P-MODE button on Boombox or press
MEMORY KEY on the remote control, “P01” will flash
on the display. Then rotate the TUNING knob on the
Boombox or press TUN- / Fast Backwards or TUN+ /
Fast Forwards on the remote control to select the first
desired station.
2. Press PROG./P-MODE button on Boombox or MEMORY
KEY on the remote control, then press the Fast Forwards
/ +10 button or Fast Backwards / -10 on Boombox or
TUN- / Fast Backwards or TUN+ / Fast Forwards key on
the remote control to choose the desired sequence you
want to store, then press the PROG./P-MODE button on
Boombox or press MEMORY key on the remote control
again to enter.
3. Search another station, repeat steps (1) & (2) until
all desired stations stored. Up to 30 stations can be
programmed.
4. Press the Fast Backwards / -10 or Fast Forwards / +10 or
FOLD./10/M UP/DOWN button on the remote to listen to
the stored station directly.
CD/MP3 OPERATION
Discs for Playback
This system can playback all digital audio CD/MP3, finalized
digital audio CD-Recordable (CD-R) discs, finalized digital
audio CD-Rewritable (CD-RW) discs and CD-DA format
digital audio CD/CD-R/CD-RW discs.
10
LOADING A DISC
1. Press the FUNCTION button on Boombox or on the
remote control to select “CD” mode.
2. Press the PUSH TO OPEN button to open the CD door,
“OPEN” will be shown on the display.
3. Place an audio CD/MP3 DISC into the tray with the front
side facing up.
4. Close the CD door. The display will show a flashing
“READING”, then the total number of tracks would be
shown and the playback will start from track.
5. To remove the CD, press the STOP button on Boombox
or on the remote control to turn off the Boombox, then
press the PUSH TO OPEN button to open the CD
compartment lid. Hold the CD by its edges, and take it out
carefully.
Note:
1. Make sure the disc is stopped before opening the CD
DOOR.
2. To ensure good system performance; wait until the
Boombox completely reads the disc before proceeding.
3. If no disc loaded into the tray, or the disc is unreadable,
the display will show “NO DISC”.
PLAYING A DISC
1. The playback starts from track 1 automatically when
reading the disc. To pause playback, press / PAIR
button on Boombox or key on the remote control. The
current playing time will flash on the display. To resume
playback, press / PAIR button on Boombox or key on
the remote control again.
2. To stop playback, press the STOP button on Boombox or
on the remote control, the total number of tracks will show
on the display.
11
SELECTING A DESIRED TRACK/PASSAGE
To select a desired track
Press the Fast Forwards / +10 or Fast Backwards / -10
button on Boombox or “TUN+ / Fast Forwards” or “TUN- /
Fast Backwards” key on the remote control on stop mode or
during playing until the desired track appears on the display.
It will start play automatically.
To search for a particular passage during playback (track
scanning at high speed)
Press and hold the Fast Forwards / +10 or Fast Backwards
/ -10 button on Boombox or TUN+ / Fast Forwards or
TUN- / Fast Backwards key on the remote control to scan
the current playing track at high speed until desired point
(passage) appears, then release the button for normal
playback mode. Playback will start again from this point.
To select a song which track number exceeds 10 (for
MP3 disc only)
To select a song/track which number exceeds 10, press
and hold the Fast Forwards / +10 button on Boombox in
stop mode or press FOLD./10/M UP button on the remote
control during playback each time to skip forward 10 tracks
in stop mode, then press the Fast Forwards / +10 button on
Boombox or TUN+ / Fas Forwards key on the remote control
to select desired track.
To select a desired folder (for MP3 disc that contains
more than one folder)
To select a desired folder during playback, press and hold
the FOLD./10/M UP/DOWN button on the remote control to
12
next/previous folder.
PROGRAMING TRACKS
Programming tracks of disc are possible when playback is
stopped. Up to 20 tracks for CD disc and 99 tracks for MP3
disc can be stored in the memory in any order.
1. In stop mode, press the PROG./P-MODE button on
Boombox or P-MODE key on the remote to enter program
setting, the PROG logo will flash on the display and show
P01.
2. Press the Fast Forwards / +10 button on Boombox or
TUN+ / Fast Forwards on the remote control to select the
first desired track to be programmed. (example: track 2)
3. Press the PROG./P-MODE button on Boombox or
P-MODE key on the remote to enter. The display would
flash PROG and show P02.
4. Repeat steps 2 & 3 to store other desired tracks until all
tracks programmed.
5. Press the / PAIR button on Boombox or key on
the remote control to start playback from the first
programmed track.
6. Press the STOP button on Boombox or on the remote
control to stop program playback. To clear the program,
you may press STOP button on Boombox or on the
remote control when the disc stopped and open the CD
compartment lid, the program will be erased.
13
REPEAT PLAY
You can play one track or all tracks on the disc repeatedly.
To Repeat a Single Track
1. Press PROG./P-MODE button on Boombox or press
P-MODE key on the remote control during play, the
display will show a steady “ ” and the current track will
be played over an over again till you press the STOP
button on Boombox or on the remote control.
2. To cancel repeat play, press PROG./P-MODE button on
Boombox or press P-MODE key on the remote control
until “ ” disappears from the display.
To repeat all the Tracks
1. Press PROG./P-MODE button on Boombox or press
P-MODE key on the remote control until the “ ALL”
shows steadily on the display, all tracks on the disc will be
played over and over again till you press the STOP button
on Boombox or on the remote control.
2. To cancel repeat play, press the PROG./P-MODE button
on Boombox or press P-MODE key on the remote control
ALL” disappears from the display.
until “
To repeat the folder (only for MP3 disc which contains more
than one folder)
1. Press the PROG./P-MODE button on Boombox or press
P-MODE key on the remote control until “ DIR ” show
steadily on the display, the current folder will be repeated
over and over again till you press the STOP button on
Boombox or on the remote control.
2. To cancel repeat play, press the PROG./P-MODE button
on Boombox or press P-MODE key on the remote control
until “ DIR ” disappear from the display.
14
RANDOM PLAY
Press the PROG./P-MODE button on Boombox or P-MODE
key on the remote control in play mode till the “RAN” shows
steadily on the display, the random play will start from next
track automatically, until all tracks are played over and then
it will stop. Press the PROG./P-MODE button on Boombox
or P-MODE key on the remote control again until the “RAN”
disappears from the display to cancel.
INTRO PLAY
Press the PROG. /P-MODE button on Boombox or press
P-MODE key on the remote control in play mode till the
“INTRO” shows steadily on the display, the intro play will
start and scan 10 seconds for every track. To cancel intro
play, press the PROG./P-MODE button on Boombox or press
P-MODE key on the remote control until “INTRO ” disappear
from the display.
LISTENING TO USB/SD CARD
USB OPERATION
1. Press the FUNCTION button on Boombox or on the
remote control to select “USB” mode.
2. Connect the USB to the USB INPUT. The LCD will
show the total number of tracks stored in the USB. The
playback stars from track 1 automatically after reading the
USB.
3. To pause playback, press / PAIR button on Boombox or
key on the remote control. The current playing time will
flash on the display. To resume playback, press / PAIR
button on Boombox or key on the remote control again.
4. Press the STOP button on Boombox or on the remote
control to stop playing. The display will show total number
of USB and STOP.
15
5. Proceed program play/repeat play (repeat 1- repeat folder
- repeat all) /random play/intro play operation as the same
described in above “CD/MP3 OPERATION”.
6. It supports 32GB (USB)
CAUTION:
Do not use any USB extension cable for connecting the USB
bar which may cause harmful interference
SD CARD OPERATION
1. Press the FUNC. button on Boombox or on the remote
control to select “CARD” mode.
2. Connect the SD CARD to the SD INPUT. The LCD will
show the total number of tracks stored in the SD CARD.
The playback stars from track 1 automatically after
reading.
3. To pause playback, press
/ PAIR button on Boombox
or key on the remote control. The current playing time
will flash on the display. To resume playback, press /
PAIR button on Boombox or key on the remote control
again.
4. Press the STOP button on Boombox or on the remote
control to stop playing. The display will show total number
of USB and STOP.
5. Proceed program play/repeat play (repeat 1- repeat folder
- repeat all) /random play/intro play operation as the same
described in above “CD/MP3 OPERATION”.
6. It supports 32GB (SD CARD)
16
BLUETOOTH OPERATION
1. Press the FUNC. button on Boombox or on the remote
control to switch to BLUETOOTH function, the LCD will
display “bt ” and the Pair/Standby indicator will flash at
high speed.
2. Turn on the Bluetooth function on the device, scan
the Boombox “DBU-58” and connect, then input the
password 0000 if required, the Pair/Standby blue light will
light up to indicate connection done, and the display will
show “bt”. Press / PAIR button on the Boombox or play
key on the device to start playback. If the Boombox can’t
connect the relative Bluetooth within 2 minutes, press the
/ PAIR button on Boombox or PAIR key on the remote
control to reconnect.
3. Rotate the VOLUME knob to your desired level.
4. Press Fast Forward / +10 button or Fast Backwards /
-10 on the Boombox or TUN+ / Fast Forwards or TUN- /
Fast Backwards key on the remote control to choose the
desired track.
5. To stop playback, press / PAIR button on Boombox or
key on the remote control.
Note: The Bluetooth works best within 10 meters.
AUX-IN OPERATION
1. Press the FUNCTION button on Boombox or on the
remote control to select “AUX” mode.
2. Insert the AUX line plug into the AUX IN jack (Φ3.5mm)
on the player, music from the device would be amplified
and exported from the speakers.
3. Adjust the volume on the Boombox or on the device to
your desired level.
4. Proceed and next/previous on the device.
17
COMPACT DISC MAINTENANCE
1. Always use a compact disc bearing the mark as shown.
2. Notes on handling discs
• Removing the disc from its storage case and loading it.
• Do not touch the reflective recorded surface.
• Do not stick paper or write anything on the surface.
• Do not bend the disc.
3. Storage
• Store the disc in its case.
• Do not expose discs to direct sunlight or high
temperatures, high humidity or dusty places.
4. Cleaning a disc
• Should the disc become soiled, wipe off dust, dirt and
fingerprints with a soft cloth.
• The disc should be cleaned from the centre to the edge.
• Never use benzene, thinners, record cleaner fluid or
anti-static spray.
• Be sure to close the CD door, so the lens is not
contaminated by dust.
• Do not touch the lens.
18
Product Specifications
Power Requirement
Power
Consumption
Standby
Consumption
AC 100-240V ~60/50Hz
DC 12V UM-1/D x 8pcs
48 Watts
<0.5 Watts
Dimensions
49.2(W) x 19.8(H) x 21(D)cm
Operation
Temperature
5ºC - 35ºC
Bluetooth Version
3.0
Receiving Bands
FM
Frequency Range
FM 87.5 - 108MHz
Optical Pickup
3 - Beam Laser
Frequency
Response
100Hz - 16 KHz
Power Output
12.5W x 2
Accessories
Instruction Manual
AC Cord
Remote Control
NOTE:
Specifications are subject to change for continuous
improvement, we reserve the rights to modification without
prior notice.
19
JD Williams Ltd.
20
Download PDF
Similar pages