Serial Device Servers
Product Selection Guides
General-purpose Device Server Selection Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-2
Industrial-grade Device Server Selection Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-7
Embedded Device Servers Selection Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-8
General-purpose Device Servers
Introduction to Serial Device Servers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-9
NPort® DE-211/311 1-port RS-232/422/485 device servers . . . . . . . . . . . . . . . . . . . . . 8-14
NPort® 5100 Series 1-port RS-232/422/485 device servers . . . . . . . . . . . . . . . . . . . . . 8-16
NPort® 5200 Series 2-port RS-232/422/485 device servers . . . . . . . . . . . . . . . . . . . . . 8-19
NPort® 5400 Series 4-port RS-232/422/485 device servers . . . . . . . . . . . . . . . . . . . . . 8-23
NPort® 5600 Rackmount Series 8 and 16-port RS-232/422/485 device servers . . . . . 8-26
NPort® 5600 Desktop Series 8-port RS-232/422/485 device servers . . . . . . . . . . . . . . 8-30
Device Servers for Industrial Automation
NPort® IA5000 Series 1 and 2-port device servers for industrial automation . . . . . . . . 8-34
Embedded Device Servers
NE-4100 Series 10/100 Mbps embedded device servers . . . . . . . . . . . . . . . . . . . . . . . . 8-38
WE-2100T Series Wireless LAN embedded serial device servers . . . . . . . . . . . . . . . . . . 8-42
8
Serial Device
Servers
Serial-to-Ethernet Solutions
General-purpose Device
Server Selection Guide
NPort® DE-211
8
NPort® DE-311
NPort® 5110/5110-T
NPort® 5130/5130-T
NPort® 5150/5150-T
LAN Interface
10/100BaseT(X)
1 x 10 Mpbs, RJ45 connector
1, RJ45 connector
1, RJ45 connector
1, RJ45 connector
1, RJ45 connector
100BaseFX
---
---
---
---
---
1.5 KV Magnetic
Isolation
√
√
√
√
√
Serial Interface
Serial Device Servers > General-purpose Device Server Selection Guide
Number of Ports
1 x RS-232/422/485
1 x RS-232/422/485
1 x RS-232
1 x RS-232/422
1 x RS-232/422/485
Connector
DB25 female
DB9 female
DB9 male
DB9 male
DB9 male
Communication
Parameters
Data Bits: 5, 6, 7, 8; Stop Bits: 1, 1.5, 2; Parity: None, Even, Odd, Space, Mark
Flow Control
RTS/CTS, XON/XOFF
RTS/CTS, XON/XOFF
RTS/CTS, DTR/DSR, XON/XOFF
XON/XOFF
RTS/CTS and DTR/DSR (RS-232
only), XON/XOFF
Baudrate
50 bps to 230.4 Kbps
50 bps to 230.4 Kbps
110 bps to 230.4 Kbps
50 bps to 921.6 Kbps
50 bps to 921.6 Kbps
15 KV ESD Protection
√
√
√
√
√
2 KV Optical Isolation
---
---
---
---
---
---
---
---
---
---
On-site Configuration
LCD Panel with 4 push
buttons
Software
Network Protocols
DHCP, BootP, Telnet,, TCP, UDP, IP, ICMP, ARP
Configuration Options
Web Console, Serial Console, Telnet Console, Windows Utility
ICMP, IP, TCP, UDP, DHCP, BOOTP, Telnet, DNS, SNMP, HTTP, SMTP
Driver Support
Windows Real COM driver (for Windows 95, 98, ME, NT, 2000, XP, 2003, Vista, XP x64, 2003 x64, Vista x64), Linux Real TTY driver, Fixed TTY driver (for SCO Unix, SCO
OpenServer, UnixWare 7, UnixWare 2.1, SVR 4.2, QNX 4.25, QNX 6, Solaris 10, FreeBSD, AIX 5.x, HP-UX 11i)
Operation Modes
Real COM, TCP Server, TCP Client, UDP, Pair Connection,
Ethernet Modem
Real COM, TCP Server, TCP Client, UDP, Pair Connection, Reverse Telnet, Ethernet Modem, Disabled
Physical Characteristics
Housing
SECC (1 mm)
SECC (1 mm)
Aluminum (1 mm)
Aluminum (1 mm)
Aluminum (1 mm)
Dimensions
67 x 100.4 x 22 mm
(2.64 x 3.95 x 0.87 in)
67 x 100.4 x 22 mm
(2.64 x 3.95 x 0.87 in)
52 x 80 x 22 mm
(2.05 x 3.15 x 0.87 in)
52 x 80 x 22 mm
(2.05 x 3.15 x 0.87 in)
52 x 80 x 22 mm
(2.05 x 3.15 x 0.87 in)
Environmental Limits
Operating Temperature
Standard Models: 0 to 55°C (32 to 131°F); Wide Temp. Models: -40 to 75°C (-40 to 167°F)
Operating Humidity
5 to 95% RH
Storage Temperature
-20 to 85°C (-4 to 185°F)
Power Requirements
Input Voltage
12 to 30 VDC
9 to 30 VDC
12 to 48 VDC
12 to 48 VDC
12 to 48 VDC
Power Consumption
150 mA @ 12 V max.
300 mA @ 9 V max.
128.7 mA @ 12 V, 72 mA @ 24 V
200 mA @ 12 V, 106 mA @ 24 V
200 mA @ 12 V, 106 mA @ 24 V
Burst Protection
(EN61000-4-4: EFT/B)
---
---
1 KV
1 KV
1 KV
Surge Protection
(EN61000-4-5)
---
---
0.5 KV
0.5 KV
0.5 KV
Regulatory Approvals
EMC
CE (EN55022 Class B, EN55024 Class B), FCC Part 15 Subpart B
Safety
UL (UL60950), TÜV (EN60950)
CE (EN55022 Class A, EN55024), FCC Part 15 Subpart B Class A
Medical
---
---
---
---
---
Marine
---
---
---
---
---
Buzzer, Realtime Clock,
Watchdog Timer
---
---
WDT only
WDT only
WDT only
MTBF
347822 hrs
225529 hrs
279122 hrs
246505 hrs
246034 hrs
Warranty
5 years
5 years
5 years
5 years
5 years
UL (UL60950-1), CUL, TÜV (EN60950-1)
Reliability
8-2
w w w. m o x a . c o m
info@moxa.com
Industrial Networking Solutions
General-purpose Device Server Selection Guide (continued)
NPort® 5210/5210-T
NPort® 5230/5230-T
NPort® 5232/5232-T
NPort® 5232I/5232I-T
10/100BaseT(X)
1, RJ45 connector
1, RJ45 connector
1, RJ45 connector
1, RJ45 connector
100BaseFX
---
---
---
---
1.5 KV Magnetic Isolation
√
√
√
√
LAN Interface
8
Serial Interface
2 x RS-232
1 x RS-232, 1 x RS-422/485
2 x RS-422/485
2 x RS-422/485
Connector
8-pin RJ45
Terminal Block
Terminal Block
Terminal Block
Communication
Parameters
Data Bits: 5, 6, 7, 8; Stop Bits: 1, 1.5, 2; Parity: None, Even, Odd, Space, Mark
Flow Control
RTS/CTS, DTR/DSR, XON/XOFF
XON/XOFF
XON/XOFF
RTS/CTS and DTR/DSR (RS-232
only), XON/XOFF
Baudrate
110 bps to 230.4 Kbps
110 bps to 230.4 Kbps
110 bps to 230.4 Kbps
110 bps to 230.4 Kbps
15 KV ESD Protection
√
√
√
√
2 KV Optical Isolation
---
---
---
√
---
---
---
---
Serial Device Servers > General-purpose Device Server Selection Guide
Number of Ports
On-site Configuration
LCD Panel with 4 push
buttons
Software
Network Protocols
ICMP, IP, TCP, UDP, DHCP, BOOTP, Telnet, DNS, SNMP, HTTP, SMTP
Configuration Options
Web Console, Serial Console, Telnet Console, Windows Utility
Driver Support
Windows Real COM driver (for Windows 95, 98, ME, NT, 2000, XP, 2003, Vista, XP x64, 2003 x64, Vista x64), Linux Real TTY driver, Fixed TTY driver (for SCO Unix,
SCO OpenServer, UnixWare 7, UnixWare 2.1, SVR 4.2, QNX 4.25, QNX 6, Solaris 10, FreeBSD, AIX 5.x, HP-UX 11i)
Web Console, Telnet Console
Operation Modes
Real COM, TCP Server, TCP Client, UDP, Pair Connection, Reverse Telnet, Disabled
Physical Characteristics
Housing
Aluminum (1 mm), providing IP30
protection
Aluminum (1 mm), providing IP30
protection
Aluminum (1 mm), providing IP30
protection
Aluminum (1 mm), providing IP30
protection
Dimensions
67 x 100.4 x 22 mm
(2.64 x 3.95 x 0.87 in)
67 x 100.4 x 22 mm
(2.64 x 3.95 x 0.87 in)
67 x 100.4 x 22 mm
(2.64 x 3.95 x 0.87 in)
67 x 100.4 x 35 mm
(2.64 x 3.95 x 1.37 in)
Environmental Limits
Operating Temperature
Standard Models: 0 to 55°C (32 to 131°F); Wide Temp. Models: -40 to 75°C (-40 to 167°F)
Operating Humidity
5 to 95% RH
Storage Temperature
-20 to 85°C (-4 to 185°F)
Power Requirements
Input Voltage
12 to 48 VDC
12 to 48 VDC
12 to 48 VDC
12 to 48 VDC
Power Consumption
305 mA @ 12 V max.
347.1 mA @ 12 V max.
259.6 mA @ 12 V max.
509.4 mA @ 12 V max.
Burst Protection
(EN61000-4-4: EFT/B)
1 KV
1 KV
1 KV
1 KV
Surge Protection
(EN61000-4-5)
0.5 KV
0.5 KV
0.5 KV
0.5 KV
DNV
DNV
Regulatory Approvals
EMC
CE (EN55022 and EN55024 Class A), FCC Part 15 Subpart B Class A
Safety
UL (UL60950-1), TÜV (EN60950-1)
Medical
EN60601-1-2 Class B, EN55011
Marine
DNV
DNV
Reliability
Buzzer, Realtime Clock,
Watchdog Timer
√
√
√
√
MTBF
134850 hrs
106955 hrs
102344 hrs
87083 hrs
Warranty
5 years
5 years
5 years
5 years
info@moxa.com
w w w. m o x a . c o m
8-3
Serial-to-Ethernet Solutions
General-purpose Device Server Selection Guide (continued)
8
NPort® 5410
NPort® 5430
NPort® 5430I
NPort® 5450
NPort® 5450I
10/100BaseT(X)
1, RJ45 connector
1, RJ45 connector
1, RJ45 connector
1, RJ45 connector
1, RJ45 connector
100BaseFX
---
---
---
---
---
1.5 KV Magnetic
Isolation
√
√
√
√
√
LAN Interface
Serial Interface
Serial Device Servers > General-purpose Device Server Selection Guide
Number of Ports
4 x RS-232
4 x RS-422/485
4 x RS-422/485
4 x RS-232/422/485
4 x RS-232/422/485
Connector
DB9 male
Terminal Block
Terminal Block
DB9 male
DB9 male
Communication
Parameters
Data Bits: 5, 6, 7, 8; Stop Bits: 1, 1.5, 2; Parity: None, Even, Odd, Space, Mark
Flow Control
DSR/DTR, RTS/CTS, XON/
XOFF
RTS/CTS and DTR/DSR
(RS-232 only), XON/XOFF
RTS/CTS and DTR/DSR
(RS-232 only), XON/XOFF
XON/XOFF
XON/XOFF
Baudrate
50 bps to 921.6 Kbps
50 bps to 921.6 Kbps
50 bps to 921.6 Kbps
50 bps to 921.6 Kbps
50 bps to 921.6 Kbps
15 KV ESD Protection
√
√
√
√
√
2 KV Optical Isolation
---
---
√
---
√
√
√
√
√
√
On-site Configuration
LCD Panel with 4 push
buttons
Software
Network Protocols
ICMP, IP, TCP, UDP, DHCP, BOOTP, Telnet, DNS, SNMP, HTTP, SMTP, SNTP, Rtelnet, ARP
Configuration Options
Web Console, Telnet Console, Windows Utility
Driver Support
Windows Real COM driver (for Windows 95, 98, ME, NT, 2000, XP, 2003, Vista, XP x64, 2003 x64, Vista x64), Linux Real TTY driver, Fixed TTY driver (for SCO Unix,
SCO OpenServer, UnixWare 7, UnixWare 2.1, SVR 4.2, QNX 4.25, QNX 6, Solaris 10, FreeBSD, AIX 5.x, HP-UX 11i)
Operation Modes
Real COM, TCP Server, TCP Client, UDP, Pair Connection, Reverse Telnet, Disabled
Physical Characteristics
Housing
SECC sheet metal (1 mm)
SECC sheet metal (1 mm)
SECC sheet metal (1 mm)
SECC sheet metal (1 mm)
SECC sheet metal (1 mm)
Dimensions
158 x 103 x 33 mm
(6.22 x 4.06 x 1.30 in)
158 x 103 x 33 mm
(6.22 x 4.06 x 1.30 in)
158 x 103 x 33 mm
(6.22 x 4.06 x 1.30 in)
158 x 103 x 33 mm
(6.22 x 4.06 x 1.30 in)
158 x 103 x 33 mm
(6.22 x 4.06 x 1.30 in)
Environmental Limits
Operating Temperature
0 to 55°C (32 to 131°F)
Operating Humidity
5 to 95% RH
Storage Temperature
-20 to 70°C (-4 to 158°F)
Power Requirements
Input Voltage
12 to 48 VDC
12 to 48 VDC
12 to 48 VDC
12 to 48 VDC
12 to 48 VDC
Power Consumption
350 mA @ 12 V max.
350 mA @ 12 V max.
585 mA @ 12 V max.
350 mA @ 12 V max.
554 mA @ 12 V max.
Burst Protection
(EN61000-4-4: EFT/B)
4 KV
4 KV
4 KV
4 KV
4 KV
Surge Protection
(EN61000-4-5)
2 KV
2 KV
2 KV
2 KV
2 KV
Regulatory Approvals
EMC
CE (EN55022 and EN55024 Class A), FCC Part 15 Subpart B Class A
Safety
UL (UL60950-1), CUL, TÜV (EN60950-1)
Medical
EN60601-1-2 Class B, EN55011
Marine
DNV
DNV
DNV
DNV
DNV
Buzzer, Realtime Clock,
Watchdog Timer
√
√
√
√
√
MTBF
205153 hrs
201699 hrs
114540 hrs
206903 hrs
206903 hrs
Warranty
5 years
5 years
5 years
5 years
5 years
Reliability
8-4
w w w. m o x a . c o m
info@moxa.com
Industrial Networking Solutions
General-purpose Device Server Selection Guide (continued)
NPort® 5610-8/16
NPort® 5610-8/16-48V
NPort® 5630-8/16
NPort® 5650-8/16
NPort®
5650-8/16-M-SC
NPort®
5650-8/16-S-SC
10/100BaseT(X)
1, RJ45 connector
1, RJ45 connector
1, RJ45 connector
1, RJ45 connector
---
---
100BaseFX
---
---
---
---
1, SC connector
1, SC connector
1.5 KV Magnetic
Isolation
√
√
√
√
√
√
Number of Ports
8 or 16 x RS-232
8 or 16 x RS-232
8 or 16 x RS-422/485
8 or 16 x
RS-232/422/485
8 or 16 x
RS-232/422/485
8 or 16 x
RS-232/422/485
Connector
8-pin RJ45
8-pin RJ45
8-pin RJ45
8-pin RJ45
8-pin RJ45
8-pin RJ45
Communication
Parameters
Data Bits: 5, 6, 7, 8; Stop Bits: 1, 1.5, 2; Parity: None, Even, Odd, Space, Mark
Flow Control
DSR/DTR, RTS/CTS,
XON/XOFF
DSR/DTR, RTS/CTS,
XON/XOFF
XON/XOFF
DSR/DTR and RTS/CTS
(RS-232 only), XON/
XOFF
DSR/DTR and RTS/CTS
(RS-232 only), XON/
XOFF
DSR/DTR and RTS/CTS
(RS-232 only), XON/
XOFF
Baudrate
50 bps to 921.6 Kbps
50 bps to 921.6 Kbps
50 bps to 921.6 Kbps
50 bps to 921.6 Kbps
50 bps to 921.6 Kbps
50 bps to 921.6 Kbps
15 KV ESD Protection
√
√
√
√
√
√
2 KV Optical Isolation
---
---
---
---
---
---
√
√
√
√
√
√
LAN Interface
8
Serial Device Servers > General-purpose Device Server Selection Guide
Serial Interface
On-site Configuration
LCD Panel with 4 push
buttons
Software
Network Protocols
ICMP, IP, TCP, UDP, DHCP, BOOTP, Telnet, DNS, SNMP, HTTP, SMTP, SNTP, ARP, PPP, SLIP, RTelnet, RFC2217
Configuration Options
Web Console, Telnet Console, Windows Utility
Driver Support
Windows Real COM driver (for Windows 95, 98, ME, NT, 2000, XP, 2003, Vista, XP x64, 2003 x64, Vista x64), Linux Real TTY driver, Fixed TTY driver (for SCO Unix,
SCO OpenServer, UnixWare 7, UnixWare 2.1, SVR 4.2, QNX 4.25, QNX 6, Solaris 10, FreeBSD, AIX 5.x, HP-UX 11i)
Operation Modes
Real COM, TCP Server, TCP Client, UDP, Pair Connection, RFC2217, Reverse Telnet, Disabled, PPP
Physical Characteristics
Housing
SECC sheet metal (1
mm)
SECC sheet metal (1
mm)
SECC sheet metal (1
mm)
SECC sheet metal (1
mm)
SECC sheet metal (1
mm)
SECC sheet metal (1
mm)
Dimensions
440 x 45 x 198 mm
(17.32 x 1.77 x 7.80 in)
440 x 45 x 198 mm
(17.32 x 1.77 x 7.80 in)
440 x 45 x 198 mm
(17.32 x 1.77 x 7.80 in)
440 x 45 x 198 mm
(17.32 x 1.77 x 7.80 in)
440 x 45 x 198 mm
(17.32 x 1.77 x 7.80 in)
440 x 45 x 198 mm
(17.32 x 1.77 x 7.80 in)
Environmental Limits
Operating Temperature
0 to 55°C (32 to 131°F)
Operating Humidity
5 to 95% RH
Storage Temperature
-20 to 75°C (-4 to 167°F)
Power Requirements
Input Voltage
100 to 240 VAC, 47 to
63 hz
±48 VDC (20 to 72
VDC, -20 to -72 VDC)
100 to 240 VAC, 47 to
63 hz
100 to 240 VAC, 47 to
63 hz
100 to 240 VAC, 47 to
63 hz
100 to 240 VAC, 47 to
63 hz
Power Consumption
141 mA @ 100 VAC, 93
mA @ 240 VAC
135 mA @ 48 VDC
152 mA @ 100 VAC, 98
mA @ 240 VAC
158 mA @ 100 VAC,
102 mA @ 240 VAC
174 mA @ 100 VAC,
113 mA @ 240 VAC
164 mA @ 100 VAC,
110 mA @ 240 VAC
Burst Protection
(EN61000-4-4: EFT/B)
4 KV
4 KV
4 KV
4 KV
4 KV
4 KV
Surge Protection
(EN61000-4-5)
2 KV
2 KV
2 KV
2 KV
2 KV
2 KV
Regulatory Approvals
EMC
CE (EN55022 Class A, EN55024), FCC Part 15 Subpart B Class A
NPort® 5610 only: IEC61000-4-12
Safety
UL (UL60950-1), TÜV (EN60950-1)
Medical
EN60601-1-2 Class B, EN55011
Marine
DNV
DNV
DNV
DNV
DNV
DNV
Buzzer, Realtime Clock,
Watchdog Timer
√
√
√
√
√
√
MTBF
NPort® 5610-8: 97294
hrs
NPort® 5610-16:
94928 hrs
NPort® 5610-8-48V:
96758
NPort® 5610-16-48V:
94417 hrs
NPort® 5630-8:
118405 hrs
NPort® 5630-16:
91483 hrs
NPort® 5650-8:
117584 hrs
NPort® 5650-16:
104767 hrs
NPort® 5650-M-SC-8:
116914 hrs
NPort® 5650-M-SC-16:
87528 hrs
NPort® 5650-S-SC-8:
116914 hrs
NPort® 5650-S-SC-16:
87528 hrs
Warranty
5 years
5 years
5 years
5 years
5 years
5 years
Reliability
info@moxa.com
w w w. m o x a . c o m
8-5
Serial-to-Ethernet Solutions
General-purpose Device Server Selection Guide (continued)
8
NPort® 5610-8-DT
NPort® 5610-8-DT-J
NPort® 5650-8-DT
NPort® 5650I-8-DT
NPort® 5650-8-DT-J
10/100BaseT(X)
2, RJ45 connector
2, RJ45 connector
2, RJ45 connector
2, RJ45 connector
2, RJ45 connector
100BaseFX
---
---
---
---
---
1.5 KV Magnetic
Isolation
√
√
√
√
√
Number of Ports
8 x RS-232
8 x RS-232
8 x RS-232/422/485
8 x RS-232/422/485
8 x RS-232/422/485
Connector
DB9 male
8-pin RJ45
DB9 male
DB9 male
8-pin RJ45
Communication
Parameters
Data Bits: 5, 6, 7, 8; Stop Bits: 1, 1.5, 2; Parity: None, Even, Odd, Space, Mark
Flow Control
DSR/DTR, RTS/CTS, XON/
XOFF
DSR/DTR, RTS/CTS, XON/
XOFF
DSR/DTR and RTS/CTS
(RS-232 only), XON/XOFF,
ADDC®
DSR/DTR and RTS/CTS
(RS-232 only), XON/XOFF,
ADDC®
DSR/DTR and RTS/CTS
(RS-232 only), XON/XOFF,
ADDC®
Baudrate
50 bps to 921.6 Kbps
50 bps to 921.6 Kbps
50 bps to 921.6 Kbps
50 bps to 921.6 Kbps
50 bps to 921.6 Kbps
15 KV ESD Protection
√
√
√
√
√
2 KV Optical Isolation
---
---
---
Ö
---
√
√
√
√
√
LAN Interface
Serial Interface
Serial Device Servers > General-purpose Device Server Selection Guide
On-site Configuration
LCD Panel with 4 push
buttons
Software
Network Protocols
ICMP, IP, TCP, UDP, DHCP, BOOTP, Telnet, DNS, SNMP, HTTP, SMTP, SNTP, Rtelnet, ARP, RFC2217
Configuration Options
Web Console, Telnet Console, Windows Utility
Driver Support
Windows Real COM driver (for Windows 95, 98, ME, NT, 2000, XP, 2003, Vista, XP x64, 2003 x64, Vista x64), Linux Real TTY driver, Fixed TTY driver (for SCO Unix, SCO
OpenServer, UnixWare 7, UnixWare 2.1, SVR 4.2, QNX 4.25, QNX 6, Solaris 10, FreeBSD, AIX 5.x, HP-UX 11i)
Operation Modes
Real COM, TCP Server, TCP Client, UDP, Pair Connection, RFC2217, Reverse Telnet, Disabled, PPP
Physical Characteristics
Housing
SECC sheet metal (0.8 mm)
SECC sheet metal (0.8 mm)
SECC sheet metal (0.8 mm)
SECC sheet metal (0.8 mm)
SECC sheet metal (0.8 mm)
Dimensions
197 x 44 x 135.5 mm
(7.76 x 1.73 x 5.33 in)
197 x 44 x 135.5 mm
(7.76 x 1.73 x 5.33 in)
197 x 44 x 135.5 mm
(7.76 x 1.73 x 5.33 in)
197 x 44 x 135.5 mm
(7.76 x 1.73 x 5.33 in)
197 x 44 x 135.5 mm
(7.76 x 1.73 x 5.33 in)
Environmental Limits
Operating Temperature
0 to 55°C (32 to 131°F)
Operating Humidity
5 to 95% RH
Storage Temperature
-20 to 70°C (-4 to 158°F)
Power Requirements
Input Voltage
12 to 48 VDC
12 to 48 VDC
12 to 48 VDC
12 to 48 VDC
12 to 48 VDC
Power Consumption
621 mA @ 12 V, 140 mA @
48 V
621 mA @ 12 V, 140 mA @
48 V
580 mA @ 12 V, 156 mA @
48 V
1066 mA @ 12 V, 200 mA @
48 V
580 mA @ 12 V, 156 mA @
48 V
Burst Protection
(EN61000-4-4: EFT/B)
4 KV
4 KV
4 KV
4 KV
4 KV
Surge Protection
(EN61000-4-5)
2 KV
2 KV
2 KV
2 KV
2 KV
Regulatory Approvals
EMC
CE (EN55022 Class A, EN55024), FCC Part 15 Subpart B Class A
Safety
UL (UL60950-1), TÜV (EN60950-1)
Medical
---
---
---
---
---
Marine
---
---
---
---
---
Buzzer, Realtime Clock,
Watchdog Timer
√
√
√
√
√
MTBF
163356 hrs
Warranty
5 years
5 years
5 years
5 years
5 years
Reliability
8-6
w w w. m o x a . c o m
info@moxa.com
Industrial Networking Solutions
Industrial-grade Device Server
Selection Guide
NPort®
IA5150/5150-T
NPort®
IA5150I/5150I-T
NPort®
IA5150-M-SC/5150M-SC-T
NPort®
IA5150I-M-SC/5150IM-SC-T
NPort®
IA5150-S-SC/5150S-SC-T
NPort®
IA5150I-S-SC/5150IS-SC-T
NPort®
IA5250/5250-T
LAN Interface
2, RJ45 connector
2, RJ45 connector
---
---
---
---
2, RJ45 connector
100BaseFX
---
---
Multi-mode, SC
connector
Multi-mode, SC
connector
Single-mode, SC
connector
Single-mode, SC
connector
---
1.5 KV Magnetic
Isolation
√
√
---
---
---
---
√
8
Serial Device Servers > Industrial-grade Device Server Selection Guide
10/100BaseT(X)
Serial Interface
Number of Ports
1 x RS-232/422/485
1 x RS-232/422/485
1 x RS-232/422/485
1 x RS-232/422/485
1 x RS-232/422/485
1 x RS-232/422/485
2 x RS-232/422/485
Connector
RS-232: DB9 male,
RS-422/485:
Terminal Block
RS-232: DB9 male,
RS-422/485:
Terminal Block
RS-232: DB9 male,
RS-422/485: Terminal
Block
RS-232: DB9 male,
RS-422/485:
Terminal Block
RS-232: DB9 male,
RS-422/485:
Terminal Block
RS-232: DB9 male,
RS-422/485:
Terminal Block
DB9 male
Communication
Parameters
Data Bits: 5, 6, 7, 8; Stop Bits: 1, 1.5, 2; Parity: None, Even, Odd, Space, Mark
Flow Control
RTS/CTS (RS-232 only), XON/XOFF
Baudrate
110 bps to 230.4 Kbps
15 KV ESD Protection
√
√
√
√
√
√
√
2 KV Optical Isolation
---
√
---
√
---
√
---
Software
Network Protocols
ICMP, IP, TCP, UDP, DHCP, BOOTP, Telnet, Rtelnet, DNS, SNMP, HTTP, SMTP, SNTP
Configuration Options
Web Console, Serial Console, Telnet Console, Windows Utility
Driver Support
Windows Real COM driver (for Windows 95, 98, ME, NT, 2000, XP, 2003, Vista, XP x64, 2003 x64, Vista x64), Linux Real TTY driver, Fixed TTY driver (for SCO Unix, SCO
OpenServer, UnixWare 7, UnixWare 2.1, SVR 4.2, QNX 4.25, QNX 6, Solaris 10, FreeBSD, AIX 5.x, HP-UX 11i)
Operation Modes
Real COM, TCP Server, TCP Client, UDP, Pair Connection, Ethernet Modem, Reverse, Telnet, Disabled
Physical Characteristics
Housing
Polycarbonate (2 mm)
IP30 protection
√
Dimensions
29 x 89.2 x 118.5 mm (0.82 x 3.51 x 4.57 in)
DIN-Rail, Wall
Mountable
√
√
√
√
√
√
√
√
√
√
√
√
√
Environmental Limits
Operating Temperature
Standard Models: 0 to 55°C (32 to 131°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)
Operating Humidity
5 to 95% RH
Storage Temperature
-20 to 85°C (-4 to 185°F)
Power Requirements
Input Voltage
12 to 48 VDC
12 to 48 VDC
12 to 48 VDC
12 to 48 VDC
12 to 48 VDC
12 to 48 VDC
12 to 48 VDC
Redundant Power
Inputs
√
√
√
√
√
√
√
Power Consumption
360 mA @ 12V max.
420 mA @ 12V max.
500 mA @ 12V max.
510 mA @ 12V max.
470 mA @ 12V max.
490 mA @ 12V max.
440 mA @ 12V max.
Regulatory Approvals
EMC
FCC Part 15 Subpart B Class A, CE EN55022 Class A, CE EN55024
Safety
UL60950-1, UL 508, TÜV EN60950-1
Hazardous Location
UL/cUL Class 1 Division 2 Groups A, B, C and D; ATEX Class Zone 2
IEC
IEC60068-2-27 (Shock); IEC60068-2-23 (Freefall); IEC60068-2-6 (Vibration)
EN
EN61000-4-2 (ESD) Level 3; EN61000-4-3 (RS) Level 3; EN61000-4-4 (EFT) Level 4; EN61000-4-5 (Surge) Level 3; EN61000-4-6 (CS) Level 3; EN61000-4-8 Passed;
EN61000-4-11 Passed; EN61000-4-12 Passed
Other
Medical (ATEX Class 1 Zone 2); Marine (DNV)
Reliability
Buzzer, Realtime Clock,
Watchdog Timer
√
Warranty
5 years (see www.moxa.com/warranty)
√
√
√
info@moxa.com
√
w w w. m o x a . c o m
√
√
8-7
Serial-to-Ethernet Solutions
Embedded Device Server
Selection Guide
8
NE-4110S
NE-4110A
NE-4120S
NE-4120A
NE-4100T
WE-2100T
Form Factor
Typical Installation Examples
Type
Stand-alone module
Stand-alone module
Drop-in
Drop-in
Dimensions
57 × 40 mm (2.24 x 1.57 in)
57 × 40 mm (2.24 x 1.57 in)
45 × 36 mm (1.77 x 1.42 in)
54 x 40 x 13.3 mm (2.13 x 1.57 x 0.52 in)
LAN Interface
Serial Device Servers > Embedded Device Server Selection Guide
10/100BaseT(X)
1, RJ45
1, Pin header (5 pins)
1, Dual-in-line pin header (26 pins)
1, Dual-in-line pin connector (44 pins)
1.5 KV Magnetic Isolation
√
√
√
√
WLAN Interface
Standard Compliance
---
---
---
IEEE 802.11a/b/g
Radio Frequency Type
---
---
---
DSSS, CCK, OFDM
Wireless Security
---
---
---
SEP, SPA, SPA2, 802.11i
Network Modes
---
---
---
Infrastructure (a/b/g), Ad Hoc (b/g)
Serial Interface
Number of Ports
2
2
2
2
Standards for Port 1
NE-4110S: RS-232
NE-4110A: RS-422/485
NE-4120S: RS-232
NE-4120A: RS-422/485
TTL
TTL
Standards for Port 2
TTL console port
TTL console port
TTL console port
TTL console port
Communication Parameters
Data Bits: 5, 6, 7, 8; Stop Bits: 1, 1.5, 2; Parity: None, Even, Odd, Space, Mark
Flow Control
RTS/CTS, XON/XOFF
Baudrate
110 bps to 230.4 Kbps
50 bps to 921.6 Kbps
Network Protocols
ICMP, ARP, IP, TCP, UDP, DHCP, Telnet, HTTP, SNMP, SMTP
ICMP, IP, TCP, UDP, DHCP, Telnet, DNS, SNMP,
HTTP, SMTP, SNTP, SSH, HTTPS
Configuration Options
Web Console, Serial Console, Telnet Console, Windows Utility (for Windows 95, 98, ME, NT, 2000, XP,
2003)
Web Console, Serial Console, Telnet Console,
Windows Utility (for Windows 95, 98, ME, NT,
2000, XP, 2003, Vista), Serial command mode
(configured through the data port)
Driver Support
Windows Real COM driver (for Windows 95, 98, ME, NT, 2000, XP, 2003, XP x64, 2003 x64), Linux Real
TTY driver, Unix
Windows COM driver (for Windows 98, ME, NT,
2000, XP, 2003, XP x64, 2003 x64, Vista), Linux
Real TTY driver, SCO Unix, SCO OpenServer 5,
UnixWare 7, UnixWare 2.1.x, SVR4.2, QNX
Operation Modes
Real COM, TCP Server, TCP Client, UDP
Real COM, TCP Server, TCP Client, UDP,
RFC2217
Standard Models: 0 to 55°C (32 to 131°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)
0 to 55°C (32 to 131°F)
Software
Environmental Limits
Operating Temperature
Operating Humidity
5 to 95% RH
Storage Temperature
-20 to 85°C (-4 to 185°F)
Surface Temperature (at full baudrate of 921.6 Kbps)
Top Panel
---
---
---
43°C, when air temp = 25°C
55°C, when air temp = 55°C
Bottom Panel
---
---
---
44.5°C, when air temp = 25°C
67.0°C, when air temp = 55°C
5 VDC (±5%)
5 VDC (±5%)
5 VDC (±5%)
3.3 VDC (±5%)
290 mA @ 5 VDC max.
921.6 Kbps (full speed): 540 mA
Idle: 190 mA
Ethernet mode: 670 mA
Inrush current: 2100 mA
Power Requirements
Input Voltage
Power Consumption
290 mA @ 5 VDC max.
290 mA @ 5 VDC max.
Regulatory Approvals
EMC
CE (EN55024), 55022 Class A, ETSI EN 301
489-17, ETSI EN 301 489-1, FCC Part 15
Subpart B Class A,
FCC Part 17 Subpart B Class A,
CE (EN55022 Class B EN55024), FCC Part 16 Subpart Class B
Reliability
8-8
Watchdog Timer
√
Warranty
5 years (see www.moxa.com/warranty)
√
w w w. m o x a . c o m
√
info@moxa.com
√
Industrial Networking Solutions
Introduction to
Serial
Device
Servers
Device server technology makes device networking easy
Device servers are used to connect serial devices to Ethernet LANs,
and are able to transmit data both to and from the serial device.
Moxa’s NPort® line of device servers are essentially pre-programmed
computers that have a real-time OS and built-in TCP/IP server, and
allow you to access, manage, and configure remote facilities and
equipment from anywhere in the world over the Internet.
8
No restrictions on host type or operating system
Serial Device Servers > Introduction to Serial Device Servers
Any host computer that supports the TCP/IP protocol can access the
NPort®’s serial ports, eliminating the need for special-purpose drivers.
In addition, you will not be held back by your PC’s limited number of
serial bus slots.
Real COM/TTY drivers for existing software
NPort® device servers also come with Real COM/TTY drivers for
accessing devices through a “virtual” COM or TTY port.
Serial Device Server Selection Table
General-purpose Device Servers
Device Servers with
Device Servers for Wide
RS-422/485
RS-232/422/485
Optical Isolation
Temperature Applications
NPort® 5130
NPort® DE-211
NPort® DE-311
NPort® 5150
NPort® IA5150
NPort® IA5150-M-SC
NPort® IA5150-S-SC
NPort® IA5150I
NPort®
IA5150I-M-SC
NPort®
IA5150I-S-SC
NPort® 5110-T
NPort® IA5150-T
NPort® IA5150I-T
NPort® IA5150-M-SC-T
NPort® IA5150I-M-SC-T
NPort® IA5150-S-SC-T
Number of Serial Ports
RS-232
1
NPort® 5110
2
NPort® 5210
NPort® 5232
NPort® 5230
NPort® IA5250
NPort® 5232I
NPort® 5210-T
NPort® 5230-T
NPort® 5232-T
NPort® IA5250-T
NPort® 5232I-T
4
NPort® 5410
NPort® 5430
NPort® 5450
NPort®
5430I/5450I
---
8
NPort® 5610-8
NPort® 5610-8-48V
NPort® 5610-8-DT
NPort® 5610-8-DT-J
NPort® 5630-8
NPort® 5650-8
NPort® 5650-8-M-SC
NPort® 5650-8-S-SC
NPort® 5650-8-DT
NPort® 5650-8-DT-J
NPort®
5650I-8-DT
---
NPort®
5630-16
NPort® 5650-16
NPort®
5650-16-M-SC
NPort®
5650-16-S-SC
---
---
16
NPort® 5610-16
NPort® 5610-16-48V
NOTE: See Chapter 7, “Terminal Servers,” for information about our NPort® 6000 series of serial device servers.
info@moxa.com
w w w. m o x a . c o m
8-9
Serial-to-Ethernet Solutions
NPort® Provides a Choice of Operation Modes
Socket Modes
TCP Server Mode
8
TCP Client Mode
When the NPort® is configured
for TCP Client mode, the NPort®
establishes a TCP connection between
1
TCP/IP
the attached device and a specified
Ethernet
host computer when data is received
2
TCP Client
from the attached device. After the
data has been transferred, the NPort®
automatically closes the connection.
RS-232
TCP Client mode supports up to 4
Device
simultaneous connections, allowing
multiple hosts to collect data from the
1 Request a
same serial device at the same time.
connection
When the NPort® is configured
for TCP Server Mode, each serial
port is assigned a unique IP:Port
1
TCP/IP
combination on the TCP/IP network,
Ethernet
and the NPort® waits passively
2
TCP Server
for a host computer to establish a
connection with the attached serial
device. TCP Server mode supports
RS-232
up to 4 simultaneous connections,
Device
allowing multiple hosts to collect
data from the same serial device at
1 Request a
connection
the same time.
2 Proceed with
2 Proceed with
data transmission
data transmission
Serial Device Servers > Introduction to Serial Device Servers
UDP Mode
UDP mode supports up to 4 multicasting groups. In UDP
mode, the attached device can exchange data simultaneously
with up to 4 network destinations, and at a higher speed
than when using TCP. This mode is ideal for message display
applications.
TCP/IP
Ethernet
232
Directly proceed with
data transmission
(no connection required)
RS-232
RS-
Device
Driver Modes
RFC2217 Mode
Real COM Mode
When configured for Real COM mode,
each serial port is assigned an IP:Port
combination that is mapped to a host
computer’s local COM or TTY port using
Moxa’s NPort® drivers. Legacy applications
can access the attached serial device using
the host’s local COM or TTY port, without
the need to modify serial COM software to
account for network protocols.
COM3=IP Port
TCP/IP
Ethernet
Driver Mode
When the NPort® is configured for RFC2217 mode,
each serial port is assigned an IP:Port combination
that is mapped by RFC2217-compliant drivers to
a virtual COM 232
port. The RFC2217 protocol defines
general COM port control options based on the
Telnet protocol. The NPort® supports any third
party driver that is RFC2217-compliant.
RS-232
RSDevice
Other Modes
Pair Connection Mode
When configured for Pair Connection mode, two NPort® device servers can be used to transmit RS-232 signals over Ethernet, and in this
way overcome the 15-meter limitation imposed by the RS-232 standard. One NPort® connects to the PC’s COM port, and the other NPort®
connects to the serial device. The two NPort®s are either connected to each other with a cross-over Ethernet cable, or are each connected to
an Ethernet LAN or WAN. Both data and modem control signals can be exchanged between the PC and device over Ethernet, but DCD signals
are not supported.
8-10
Ethernet Modem Mode
Reverse Telnet Mode
When configured for Ethernet
Modem mode, the serial port on
the NPort® behaves as if it were
attached to a modem, except that
data is transmitted over a network
instead of over phone lines. Ethernet
Modem Mode enables network
access for legacy software that was
originally designed to transmit data
by modem.
When configured for Reverse Telnet mode, the
NPort®’s serial ports provide a connection to a
server, with connections initiated by a host over
Ethernet. This is similar to TCP server mode,
except Reverse Telnet mode also provides
Telnet-style CR/LF conversion. Reverse
Telnet mode can be used for remote console
management, in which the NPort® is used to
enable network access to the serial console
ports of different equipment, such as routers,
switches, and servers.
w w w. m o x a . c o m
info@moxa.com
Industrial Networking Solutions
Mode Selection Flowchart
Start
NO
YES Using socket
program?
Which protocol,
TCP or UDP?
TCP
Host application is
server or client?
Using legacy
COM-based software?
Host requires more
COM ports?
YES
NO
Using MOXA's
drivers?
UDP
Need to extend
serial transmission
range?
NO
NO
YES
8
YES
Client
Need to perform
console
management?
Server
NO
YES
NO
Reverse
Telnet
Contact your
saleperson.
YES
TCP Client
Mode
TCP Server
Mode
RFC2217
Mode or TCP
Server Mode
UDP Mode
Pair
Connection
Modes
RFC2217
Mode
Typical Applications
Use only one IP address to control multiple serial devices over the network
Automatic or remote data acquisition can be accomplished with
NPort® 5000 device servers, which only require one IP address to
connect up to 16 serial devices to an Ethernet network. By specifying
the IP address and TCP port number, a host computer can access the
serial devices connected to the NPort® 5000 from over the network. In
the example shown here, data from the NPort® 5410’s first serial port
can be obtained by connecting to 192.168.10.2:4001.
Use server sharing from a central location for greater device management flexibility
Serial devices connected to the NPort® 5000 device server can
communicate over the network with more than one host computer.
Real COM
Mode
Serial Device Servers > Introduction to Serial Device Servers
Need serial control
parameters?
Centralize RS-422/485 serial device control
Up to 31 RS-485 devices, or 9 RS-422 devices, can be connected to
each serial port on the NPort® 5000 device server. The web console or
Windows utility can be used to configure RS-422 or RS-485 operation
for each port, with both 2-wire and 4-wire RS-485 supported.
info@moxa.com
w w w. m o x a . c o m
8-11
Serial-to-Ethernet Solutions
NPort® Administrator Makes Installation Easy
NPort® Administrator is designed to make it easy to install and
configure NPort® 5000 device servers over the network. Five groups
of functions are supported to allow off-line COM mapping, device
monitoring, and searching for NPort® device severs over the network.
Both NPort® Administrator and an IP Serial Library are bundled with
NPort®’s integrated software suite, giving you everything you need to
manage, monitor, and reconfigure your NPort® from remote locations.
Configuration Features
UÊ
UÊ
UÊ
UÊ
Broadcast search over the LAN for NPort® device servers
Select and configure the NPort®’s operation mode
Upgrade the NPort®’s firmware
Export and import NPort® configurations
8
Serial Device Servers > Introduction to Serial Device Servers
Web Console Provides Exceptional Convenience
NPort® 5000 device servers are easily configured over the network with the web console or Telnet console.
Network Settings
Serial Settings
UÊ IP, netmask, gateway
UÊ Static IP, DHCP, BOOTP
UÊ DNS server
UÊ
UÊ
UÊ
UÊ
Baudrate
Data bits, stop bit, parity
Flow control
Communication interface
Operation Settings
UÊ
UÊ
UÊ
UÊ
UÊ
UÊ
UÊ
UÊ
8-12
Operation mode
TCP alive check time
Inactivity time
Delimiter
Force transmit
Packet length
Allow driver control
Maximum connection
w w w. m o x a . c o m
info@moxa.com
Industrial Networking Solutions
IP Serial Library
What is IP Serial Library?
The IP Serial Library is a collection of Windows functions for NPort®
5000 device servers. Serial command sets and common subroutines
are provided. The purpose of the library is to help reduce complexity
and increase efficiency when programming serial communication
applications that run over a TCP/IP network. For example, Telnet
is limited because it can only transfer data but cannot monitor or
configure serial line parameters. The IP Serial Library can be used to
add new functionality to your Telnet sessions.
Use IP Serial Library for easier socket-based serial COM programming
For programmers who are familiar with serial communication, the IP
Serial Library provides well-designed function calls that have the same
style as Moxa’s PComm Library.
The IP Serial Library is amazingly simple and easy to understand.
By including the library in your VB, C, or Delphi programming
environment, you will be able to develop TCP/IP applications that can
control serial communication parameters.
When Real COM mode is used, the NPort® serial device servers use
two TCP ports for communication between an attached device and
a host computer’s Real COM driver. The two ports, a data port and a
command port, provide pure data transfer without requiring encoding
and decoding. With the IP Serial Library, only one port is used to
communicate with a user’s application, and no encoding or decoding
is required.
char NPort®ip=“192.168.1.10”;
char buffer[255];int port = 1;
/*data buffer, 255 chars */
int portid;
/*port handle*/
nsio_init();
/*initialize IP Serial Library*/
portid = nsio_open(NPort®ip, port);
/*1st port, NPort® IP=192.168.1.10 */
nsio_ioctl(portid, B9600, (BIT_8 | STOP_1 | P_NONE) );
/*set 9600, N81 */
sleep(1000);
/* wait for 1000 ms for data */
nsio_read(port, buffer, 200);
/* read 200 bytes from port 1 */
nsio_close(portid);
/* clost this serial port */
nsio_end();
/* close IP Serial Library */
IP Serial API Function List
Server Control
Port Control
Input/Output Data
Port Status Inquiry
Miscellaneous
nsio_init
nsio_open
nsio_read
nsio_lstatus
nsio_break
nsio_end
nsio_close
nsio_SetReadTimeouts
nsio_data_status
nsio_break_on
nsio_resetserver
nsio_ioctl
nsio_write
---
nsio_break_off
nsio_checkalive
nsio_fl owctrl
nsio_SetWriteTimeouts
---
nsio_breakcount
---
nsio_DTR
---
---
---
---
nsio_RTS
---
---
---
---
nsio_lctrl
---
---
---
---
nsio_baud
---
---
---
---
nsio_resetport
---
---
---
info@moxa.com
w w w. m o x a . c o m
Serial Device Servers > Introduction to Serial Device Servers
IP Serial Library Example
8
8-13
Serial-to-Ethernet Solutions
NPort® DE-211/311
1-port RS-232/422/485 serial device servers
› 3-in-1 serial port: RS-232, RS-422, or RS-485
› Versatile operation modes including TCP Server, TCP Client,
NPort® DE-311
UDP, Ethernet Modem, and Pair Connection
8
› Real COM/TTY drivers for Windows and Linux
› 10M and 100M Ethernet speeds detected automatically
› 2-wire RS-485 with patented Automatic Data Direction Control
(ADDC®)
› Built-in 15 KV ESD protection for all serial signals
NPort® DE-211
Serial Device Servers > NPort® DE-211/311
The certification logos shown here apply to some or all of the products in this
section. Please see the Specifications section or Moxa’s website for details.
Overview
The NPort® DE-211 and DE-311 are 1-port serial device servers that
support RS-232, RS-422, 4-wire RS-485, and 2-wire RS-485. The
DE-211 supports 10 Mbps Ethernet connections and has a DB25
female connector for the serial port. The DE-311 supports 10/100
Specifications
Ethernet Interface
Mbps Ethernet connections and has a DB9 female connector for the
serial port.
Both device servers are ideal for applications that involve information
display boards, PLCs, flow meters, gas meters, CNC machines, and
biometric identification card readers.
Driver Support: Windows Real COM driver (for Windows 95, 98, ME,
NT, 2000, XP, 2003, Vista, XP x64, 2003 x64, Vista x64), Linux Real
TTY driver, Fixed TTY driver (for SCO Unix, SCO OpenServer,
UnixWare 7, UnixWare 2.1, SVR 4.2, QNX 4.25, QNX 6, Solaris 10,
FreeBSD, AIX 5.x, HP-UX 11i)
Number of Ports: 1
Speed:
NPort® DE-211: 10 Mbps
NPort® DE-311: 10/100 Mbps
Connector: 8-pin RJ45
Magnetic Isolation Protection: 1.5 KV built-in
Physical Characteristics
Serial Interface
Number of Ports: 1
Serial Standards: RS-232/422/485 (selectable by DIP Switch)
Connector:
NPort® DE-211: DB25 female
NPort® DE-311: DB9 female
Serial Line Protection: 15 KV ESD protection for all signals
RS-485 Data Direction Control: ADDC® (automatic data direction
control)
Serial Communication Parameters
Housing: SECC sheet metal (1 mm), providing IP30 protection
Weight: 720 g
Dimensions:
Without ears: 67 x 100.4 x 22 mm (2.64 x 3.95 x 0.87 in)
With ears: 90.2 x 100.4 x 22 mm (3.55 x 3.95 x 0.87 in)
Environmental Limits
Operating Temperature: 0 to 55°C (32 to 131°F)
Operating Humidity: 5 to 95% RH
Storage Temperature: -20 to 85°C (-4 to 185°F)
Power Requirements
Input Voltage:
DE-211: 12 to 30 VDC
DE-311: 9 to 30 VDC
Power Consumption:
NPort® DE-211: 150 mA @ 12 V max.
NPort® DE-311: 300 mA @ 9 V max.
Data Bits: 5, 6, 7, 8
Stop Bits: 1, 1.5, 2
Parity: None, Even, Odd, Space, Mark
Flow Control: RTS/CTS, XON/XOFF
Baudrate: 50 bps to 230.4 Kbps
Regulatory Approvals
Serial Signals
EMC: CE (EN55022 Class B, EN55024 Class B), FCC Part 15
Subpart B
Safety: UL (UL60950), TÜV (EN60950)
RS-232: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
RS-422: Tx+, Tx-, Rx+, Rx-, RTS+, RTS-, CTS+, CTS-, GND
RS-485-4w: Tx+, Tx-, Rx+, Rx-, GND (DE-211 only)
RS-485-2w: Data+, Data-, GND
Warranty
Warranty Period: 5 years
Details: See www.moxa.com/warranty
Software
Network Protocols: DHCP, BootP, Telnet, , TCP, UDP, IP, ICMP, ARP
Configuration Options: Web Console, Serial Console, Telnet Console,
Windows Utility
8-14
w w w. m o x a . c o m
info@moxa.com
Industrial Networking Solutions
Dimensions
ON
1
DIP
2
3
4
22.0 mm
(0.87 in)
NPort® DE-211
22.0 mm
(0.87 in)
NPort® DE-311
22.0 mm
(0.87 in)
22.0 mm
(0.87 in)
RESET
DC-IN
10/100M
Ethernet
DC-IN
RESET 10BaseT
Ethernet
SW
O 6 mm
(0.24 in)
PWR
O 4 mm
(0.16 in)
PWR
Link
O 6 mm
(0.24 in)
O 4 mm
(0.16 in)
Link
Ready
Ready
Serial
SW1 Connection
SW2 SW3
Console
ON (19200,N,8,1)
OFF OFF
OFF ON
Data
OFF
Comm.
ON OFF
ON ON
21.3 mm
(0.8 in)
Express
DE-211 RS-232/422/485 Device Server
Serial
SW1 Connection
Interface Mode
RS-232
RS-232
RS-422
RS-485 by RTS
RS-485 ADDC
Serial
O 7 mm
(0.28 in)
21.3 mm
(0.8 in)
ON
RS-232
Console
OFF
Data
Comm
SW2
OFF
OFF
ON
ON
ON
ON
SW3
OFF
ON
OFF
ON
OFF
ON
SW4
OFF
ON
ON
ON
OFF
OFF
Serial Interface Mode
RS-232
RS-422
4-Wire RS-485 by RTS
4-Wire RS-485 by ADDC
2-Wire RS-485 by RTS
4-Wire RS-485 by ADDC
12.5 mm
(0.49 in)
25 mm
(0.98 in)
Express
DE-311 RS-232/422/485 Device Server
Serial Rx
100.4 mm
(3.95 in)
12.5 mm
(0.49 in)
25 mm
(0.98 in)
100.4 mm
(3.95 in)
Serial Tx
O 7 mm
(0.28 in)
Serial
SW
22.0 mm
(0.87 in)
22.0 mm
(0.87 in)
1 2 3
67.0 mm
(2.64 in)
78 mm
(3.07 in)
67.0 mm
(2.64 in)
78 mm
(3.07 in)
90.2 mm
(3.55 in)
90.2 mm
(3.55 in)
Pin Assignment
NPort® DE-211
(RS-232/422/485, DB25 female connector)
25
RXDA(-) / DATAA(-)
RXDB(+) / DATAB(-)
DSR (IN) 20
TXDA (-) 15
TXDB (+) 14
NPort® DE-311
(RS-232/422/485, DB9 female connector)
13 Power GND for 12-30 VDC
12 Unreg. 12-30 VDC (in)
PIN
1
2
3
4
5
6
7
8
9
1 2 3 4 5
10 Power GND for 5 VDC
9 Reg. +5 VDC (out)
8 DCD (in)
7 SGND
6 DTR (out)
5 RTS (out)
4 CTS (in)
3 TxD (out)
2 RxD (in)
1 Do not use this pin*
6 7 8 9
RS-232
DCD
TxD
RxD
DSR
GND
DTR
CTS
RTS
----
RS-422/485-4w
RxD-(A)
RxD+(B)
TxD+(B)
TxD-(A)
GND
CTS-(A)
CTS+(B)
RTS+(B)
RTS-(A)
RS-485-2w
------Data+(B)
Data-(A)
GND
-------------
Serial Device Servers > NPort® DE-211/311
42.3 mm
(1.67 in)
42.3 mm
(1.67 in)
ON
8
Ordering Information
Available Models
Package Checklist
NPort® DE-211: 1-port RS-232/422/485 device server with 10 Mbps Ethernet connection
NPort® DE-311: 1-port RS-232/422/485 device server with 10/100 Mbps Ethernet connection
UÊ
UÊ
UÊ
UÊ
NPort® DE-311 or DE-211 serial device server
Document and Software CD
Quick Installation Guide (printed)
Warranty Card
Optional Accessories (can be purchased separately)
NP21101: DB25 male to DB9 female cable for RS-232 transmission, 30 cm (for DE-211)
NP21102: DB25 male to DB9 male cable for RS-232 transmission, 30 cm (for DE-211)
NP21103: DB25 male terminal block kit for RS-422/485 transmission (for DE-211)
TB-M25: DB25 male DIN-Rail wiring terminal (for DE-211)
TB-M9 (for DE-311): DB9 male DIN-Rail wiring terminal (for DE-311)
DK-35A: Mounting Kit for 35-mm DIN-Rail
info@moxa.com
w w w. m o x a . c o m
8-15
Serial-to-Ethernet Solutions
NPort® 5100 Series
1-port RS-232/422/485 serial devic
device servers
› Real COM/TTY drivers for Windows and Linux
› Standard TCP/IP interface and versatile operation modes
› Easy-to-use Windows utility for configuring multiple device
servers
› Built-in 15 KV ESD protection for all serial signals
› SNMP MIB-II for network management
› Configure by Telnet or web browser
› Adjustable termination resistor for RS-485 ports
8
Serial Device Servers > NPort® 5100 Series
The certification logos shown here apply to some or all of the products in this
section. Please see the Specifications section or Moxa’s website for details.
Overview
NPort® 5100 device servers are designed to make serial devices
network-ready in an instant. The small size of the servers makes
them ideal for connecting devices such as card readers and payment
terminals to an IP-based Ethernet LAN. Use the NPort® 5100 device
servers to give your PC software direct access to serial devices from
anywhere on the network.
Most Cost-effective Serial-to-Ethernet Solution
Using serial device servers to connect legacy serial devices to Ethernet
is now commonplace, and users expect device servers to be costeffective and to provide a broad selection of useful functions. With its
full support of Microsoft and Linux operating systems and solid 5-year
warranty, the NPort® 5100 series provides the best choice for serialto-Ethernet converters.
Adjustable Termination and Pull High/Low Resistors
In some critical environments, termination resistors may be needed
to prevent the reflection of serial signals. When using termination
resistors, it is also important to set the pull high/low resistors correctly
so that the electrical signal is not corrupted. Since no set of resistor
values is universally compatible with all environments, the NPort®
5100 device servers come with jumpers for adjusting termination and
pull high/low resistor values for each serial port.
Standard TCP/IP Interface and Broad Choice of Operation Modes
The NPort® 5100 device servers can be configured for TCP Server,
TCP Client, UDP Server/Client, Pair Connection, or Ethernet Modem
mode, ensuring compatibility with software based on a standard
network API (e.g., Winsock or BSD Sockets).
Real COM/TTY Drivers for Existing Software
The Real COM/TTY drivers provided with the NPort® 5100
device servers allow you to continue using software designed for
communicating through COM/TTY ports. Installation and configuration
is painless, and allows your serial devices and PC to communicate
seamlessly over a TCP/IP network. Using Moxa’s Real COM/TTY
drivers is an excellent way to preserve your software investment,
while still allowing you to enjoy the benefits of networking your serial
devices.
Easy to Troubleshoot
NPort® 5100 device servers support SNMP V2, which can be used to
monitor all units over Ethernet. Each unit can be configured to send
trap messages automatically to the SNMP manager when user-defined
errors are encountered. For users who do not use SNMP manager, an
8-16
w w w. m o x a . c o m
e-mail alert can be sent instead. Users can define the trigger for the
alerts using Moxa’s Windows utility, or the web console. For example,
alerts can be triggered by a warm start, a cold start, or a change in
password.
info@moxa.com
Industrial Networking Solutions
Appearance
NPort® 5150
NPort® 5110
NPort® 5130
Ethernet
RJ45 10/100 Mbps
Reset button
Power input
Power jack
12 to 48 VDC
Ethernet
RJ45 10/100 Mbps
Reset button
Power input
Power jack 12 to 48 VDC
Power input
Power jack
12 to 48 VDC
Reset button
Ethernet
RJ45 10/100 Mbps
8
DK-35A DIN-Rail Kit
Specifications
RS-232/422/485
RS-232
RS-422/485
Driver Support: Windows Real COM driver (for Windows 95, 98, ME,
NT, 2000, XP, 2003, Vista, XP x64, 2003 x64, Vista x64), Linux Real
TTY driver, Fixed TTY driver (for SCO Unix, SCO OpenServer,
UnixWare 7, UnixWare 2.1, SVR 4.2, QNX 4.25, QNX 6, Solaris 10,
FreeBSD, AIX 5.x, HP-UX 11i)
Ethernet Interface
Number of Ports: 1
Speed: 10/100 Mbps
Connector: 8-pin RJ45
Magnetic Isolation Protection: 1.5 KV built-in
Physical Characteristics
Serial Interface
Number of Ports: 1
Serial Standards:
NPort® 5110: RS-232
NPort® 5130: RS-422/485
NPort® 5150: RS-232/422/485
Connector: DB9 male
Serial Line Protection: 15 KV ESD protection for all signals
RS-485 Data Direction Control: ADDC® (automatic data direction
control)
Serial Communication Parameters
Data Bits: 5, 6, 7, 8
Stop Bits: 1, 1.5, 2
Parity: None, Even, Odd, Space, Mark
Flow Control: RTS/CTS and DTR/DSR (RS-232 only), XON/XOFF
Baudrate:
NPort® 5110: 110 bps to 230.4 Kbps
NPort® 5130/5150: 50 bps to 921.6 Kbps
Housing: Aluminum (1 mm)
Weight: 580 g
Dimensions:
Without ears: 52 x 80 x 22 mm (2.05 x 3.15 x 0.87 in)
With ears: 75.2 x 80 x 22 mm (2.96 x 3.15 x 0.87 in)
Environmental Limits
Serial Device Servers > NPort® 5100 Series
Available Accessory
Operating Temperature:
NPort® 5110/5130/5150: 0 to 55°C (32 to 131°F)
NPort® 5110-T: -40 to 75°C (-40 to 167°F)
Operating Humidity: 5 to 95% RH
Storage Temperature: -20 to 85°C (-4 to 185°F)
Power Requirements
Input Voltage: 12 to 48 VDC
Power Consumption:
NPort® 5110: 128.7 mA @ 12 V, 72 mA @ 24 V
NPort® 5130/5150: 200 mA @ 12 V, 106 mA @ 24 V
Power Line Protection: 1 KV burst (EN61000-4-4: EFT/B), 0.5 KV
surge (EN61000-4-5)
Serial Signals
Regulatory Approvals
RS-232: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
RS-422: Tx+, Tx-, Rx+, Rx-, GND
RS-485-4w: Tx+, Tx-, Rx+, Rx-, GND
RS-485-2w: Data+, Data-, GND
EMC: CE (EN55022 Class A, EN55024), FCC Part 15 Subpart B
Class A
Safety: UL (UL60950-1), CUL, TÜV (EN60950-1)
Reliability
Software
Network Protocols: ICMP, IP, TCP, UDP, DHCP, BOOTP, Telnet,
DNS, SNMP, HTTP, SMTP
Configuration Options: Web Console, Serial Console, Telnet Console,
Windows Utility
Automatic Reboot Trigger: Built-in WDT (watchdog timer)
MTBF (meantime between failures):
NPort® 5110: 279122 hrs
NPort® 5130: 246505 hrs
NPort® 5150: 246034 hrs
Warranty
Warranty Period: 5 years
Details: See www.moxa.com/warranty
info@moxa.com
w w w. m o x a . c o m
8-17
Serial-to-Ethernet Solutions
Dimensions
NPort® 5110
NPort® 5130
12-48
NPort® 5150
12-48
12-48
Port 1 RS-422/485
Port 1 RS-232/422/485
8
Serial Device Servers > NPort® 5100 Series
Pin Assignment
DB9 male connector
1 2 3 4 5
6 7 8 9
NPort® 5110 (RS-232)
NPort® 5130 (RS-422/485)
RS-232
PIN
RS-422/485-4w
RS-485-2w
1
DCD
1
TxD-(A)
–
1
DCD
TxD-(A)
2
RxD
2
TxD+(B)
–
2
RxD
TxD+(B)
–
3
TxD
3
RxD+(B)
Data+(B)
3
TxD
RxD+(B)
Data+(B)
4
DTR
4
RxD-(A)
Data-(A)
4
DTR
RxD-(A)
Data-(A)
5
GND
5
GND
GND
5
GND
GND
GND
6
DSR
6
–
–
6
DSR
–
–
7
RTS
7
–
–
7
RTS
–
–
8
CTS
8
–
–
8
CTS
–
–
9
–
–
9
–
–
–
PIN RS-232 RS-422/485-4w
RS-485-2w
–
Ordering Information
Available Models
Package Checklist
NPort® 5110: 1-port RS-232 device server
NPort® 5130: 1-port RS-422/485 device server
NPort® 5150: 1-port RS-232/422/485 device server
NPort® 5110-T: 1-port RS-232 device server, wide temperature (-40 to 75°C)
UÊ
UÊ
UÊ
UÊ
UÊ
Optional Accessories (can be purchased separately)
DK-35A: Mounting Kit for 35-mm DIN-Rail
8-18
NPort® 5150 (RS-232/422/485)
PIN
w w w. m o x a . c o m
info@moxa.com
NPort® 5100 series device server
Power Adaptor (see Appendix A)
Document and Software CD
Quick Installation Guide (printed)
Warranty Card
Industrial Networking Solutions
NPort® 5200 Series
2-port RS-232/422/485 serial device servers
› Small size for easy installation
› Versatile socket operation modes, including TCP Server, TCP
Client, and UDP
› Easy-to-use Windows utility for configuring multiple device
servers
› Supports 10/100M Ethernet
› Patented ADDC® (Automatic Data Direction Control) for 2-wire
and 4-wire RS-485
› Built-in 15 KV ESD protection for all serial signals
› SNMP MIB-II for network management
Standard TCP/IP Protocols and Choice of Operation Modes
NPort® 5200 device servers can operate in TCP Server, TCP Client, or
UDP operation mode, ensuring compatibility with software based on a
standard network API (Winsock, BSD Sockets).
Real COM/TTY Drivers for Existing Software
With the Real COM/TTY drivers that are provided with each NPort®,
software designed for communication with COM/TTY ports can be
instantly and seamlessly integrated into a TCP/IP network. This is an
excellent “no fuss” way to preserve your software investment and
enjoy the benefits of networking your serial devices.
Control Remote Serial Devices with TCP/IP or Traditional COM/TTY Port
By specifying the NPort® 5200’s IP address and port number, a
network sockets API can obtain access to the attached serial device
over the network, from any host computer that supports TCP/IP. For
legacy Windows or Linux software that is COM or TTY-based, Moxa’s
COM/TTY drivers provide a seamless way of operating over the
network.
Serial Device Servers > NPort® 5200 Series
The certification logos shown here apply to some or all of the products in this
section. Please see the Specifications section or Moxa’s website for details.
8
COM Driver or Network Socket Operation
Remote Host
(Windows or Linux)
Internet
Local Host
(Windows or Linux)
Ethernet
192.168.10.2:4001
NPort® 5230/5232
2-wire RS-485
Up to 32 Serial Devices
info@moxa.com
w w w. m o x a . c o m
8-19
Serial-to-Ethernet Solutions
Appearance
NPort® 5232
Ethernet
RJ45 10/100 Mbps
Reset Button
NPort® 5230
Ethernet
RJ45 10/100 Mbps
Power Input
Terminal Block
12 to 48 VDC
Power Input
Terminal Block
12 to 48 VDC
Reset
Button
NPort® 5210
Power Input
Terminal Block
12 to 48 VDC
Reset Button
Ethernet
RJ45 10/100 Mbps
DK-35A DIN-Rail Kit
8
Available Accessory
Serial Device Servers > NPort® 5200 Series
DIN-Rail Kit
(Optional)
RS-422/485
RS-232
Specifications
8-pin RJ45, RS-232
Ethernet Interface
Software
Number of Ports: 1
Speed: 10/100 Mbps
Connector: 8-pin RJ45
Magnetic Isolation Protection: 1.5 KV built-in
Network Protocols: ICMP, IP, TCP, UDP, DHCP, BOOTP, Telnet,
DNS, SNMP, HTTP, SMTP, SNTP
Configuration Options: Web Console, Serial Console (NPort®
5210/5230 only), Telnet Console, Windows Utility (NPort®
5210/5230 only)
Driver Support: Windows Real COM driver (for Windows 95, 98, ME,
NT, 2000, XP, 2003, Vista, XP x64, 2003 x64, Vista x64), Linux Real
TTY driver, Fixed TTY driver (for SCO Unix, SCO OpenServer,
UnixWare 7, UnixWare 2.1, SVR 4.2, QNX 4.25, QNX 6, Solaris 10,
FreeBSD, AIX 5.x, HP-UX 11i)
Serial Interface
Number of Ports: 2
Serial Standards:
NPort® 5210: RS-232
NPort® 5230: 1 RS-232 port, 1 RS-422/485 port
NPort® 5232: RS-422/485
Connectors:
NPort® 5210: RJ45 (8 pins)
NPort® 5230/5232: Terminal Block (5 pins per port)
Serial Line Protection:
15 KV ESD protection
2 KV isolation protection (NPort® 5232I/5232I-T)
RS-485 Data Direction Control: ADDC® (automatic data direction
control)
Serial Communication Parameters
Data Bits: 5, 6, 7, 8
Stop Bits: 1, 1.5, 2
Parity: None, Even, Odd, Space, Mark
Flow Control: RTS/CTS (RS-232 only), DTR/DSR (NPort® 5210
only), XON/XOFF
Baudrate: 110 bps to 230.4 Kbps
Serial Signals
RS-232:
NPort® 5210: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
NPort® 5230/5232: TxD, RxD, RTS, CTS, GND
RS-422: Tx+, Tx-, Rx+, Rx-, GND
RS-485-4w: Tx+, Tx-, Rx+, Rx-, GND
RS-485-2w: Data+, Data-, GND
8-20
RS-422/485
w w w. m o x a . c o m
Physical Characteristics
Housing: Aluminum (1 mm), providing IP30 protection
Weight:
NPort® 5210: 320 g
NPort® 5230/5232: 340 g
NPort® 5232I: 380 g
Dimensions:
NPort® 5210/5230/5232:
Without ears: 67 x 100.4 x 22 mm (2.64 x 3.95 x 0.87 in)
With ears: 90 x 100.4 x 22 mm (3.54 x 3.95 x 0.87 in)
NPort® 5232I:
Without ears: 67 x 100.4 x 35 mm (2.64 x 3.95 x 1.37 in)
With ears: 90 x 100.4 x 35 mm (3.54 x 3.95 x 1.37 in)
Environmental Limits
Operating Temperature:
NPort® 5210/5230/5232/5232I: 0 to 55°C (32 to 131°F)
NPort® 5210-T/5230-T/5232-T/5232I-T: -40 to 75°C (-40 to 167°F)
Operating Humidity: 5 to 95% RH
Storage Temperature: -20 to 85°C (-4 to 185°F)
info@moxa.com
Industrial Networking Solutions
Power Requirements
Reliability
Input Voltage: 12 to 48 VDC
Power Consumption:
NPort® 5210: 305 mA @ 12 V max.
NPort® 5230: 347.1 mA @ 12 V max.
NPort® 5232: 259.6 mA @ 12 V max.
NPort® 5232I: 509.4 mA @ 12 V max.
Power Line Protection: 1 KV burst (EN61000-4-4: EFT/B), 0.5 KV
surge (EN61000-4-5)
Alert Tools: Built-in buzzer and RTC (real-time clock)
Automatic Reboot Trigger: Built-in WDT (watchdog timer)
MTBF (meantime between failures):
NPort® 5210: 134850 hrs
NPort® 5230: 106955 hrs
NPort® 5232: 102344 hrs
NPort® 5232I: 87083 hrs
Warranty
Regulatory Approvals
Warranty Period: 5 years
Details: See www.moxa.com/warranty
EMC: CE (EN55022 and EN55024 Class A), FCC Part 15 Subpart B
Class A
Safety: UL (UL60950-1), TÜV (EN60950-1)
Medical: EN60601-1-2 Class B, EN55011
Marine: DNV
8
Dimensions
NPort® 5210
NPort® 5230
Serial Device Servers > NPort® 5200 Series
22.0 mm
(0.87 in)
V-
V+
RESET
10/100M
RESET
Ethernet
12-48V
O 6 mm
(0.24 in)
Ready
O 4 mm
(0.16 in)
Link
Link
P1
P2
P2
5210
Industrial RS-232 Device Server
12.5 mm
(0.49 in)
25 mm
(0.98 in)
P1
(3.95 in)
100.4 mm
V+
V-
10/100M
Ethernet
12-48V
Ready
5230
5210
Industrial RS-232/422/485 Device Server
O 7 mm
(0.28 in)
GND
R-/D-
T-
T+
GND
P2 RS-485/422
CTS
Rx
RTS
Tx
P1 RS-232
P2 RS-232
P1 RS-232
R+/D+
21.3 mm
(0.8 in)
22.0 mm
(0.87 in)
42.3 mm
(1.67 in)
67 mm
(2.64 in)
78 mm
(3.07 in)
90.2 mm
(3.55 in)
NPort® 5232I
NPort® 5232
9
35
V-
V+
RESET
V+
V-
10/100M
RESET
Ready
Link
Link
P1
P1
P2
P2
6
Ready
10/100M
Ethernet
12-48V
Ethernet
12-48V
4
7
Industrial RS-422/485 Device Server
GND
T-
R-/D-
R+/D+
T+
GND
T-
R-/D-
T+
28.7
P2 RS-485/422
9
GND
R-/D-
T+
T-
R+/D+
R+/D+
P1 RS-485/422
P2 RS-485/422
GND
R-/D-
T+
T-
R+/D+
P1 RS-485/422
5232I
5210
100.4
43
25
5232
5210
Industrial RS-422/485 Device Server
11.5
info@moxa.com
67
78
90
w w w. m o x a . c o m
8-21
Serial-to-Ethernet Solutions
Pin Assignment
PIN
1
2
3
4
GND
TxD (out)
NPort® 5232/5232I/5232-T/5232I-T
(RS-422/485, terminal block connector)
GND
R-/D-
R+/D+
GND
GND
T+
R-/D-
Tx- / Data-
GND
Tx- / Data-
Tx+ / Data+
Rx-
Rx+
Signals
Ordering Information
Package Checklist
Available Models
UÊ NPort® 5200 series device server
NPort® 5210: 2-port RS-232 device server
UÊ Power Jack to 3-pin Terminal Block Adaptor
NPort® 5230: 2-port device server with 1 RS-232 port and 1 RS-422/485 port
UÊ Document and Software CD
NPort® 5232: 2-port RS-422/485 device server
UÊ Quick Installation Guide (printed)
NPort® 5232I: 2-port RS-422/485 device server with 2 KV optical isolation
UÊ Warranty Card
NPort® 5210-T: 2-port RS-232 device server, wide temperature (-40 to 75°C)
NPort® 5230-T: 2-port device server with 1 RS-232 port and 1 RS-422/485 port, wide temperature (-40 to 75°C)
NPort® 5232-T: 2-port RS-422/485 device server, wide temperature (-40 to 75°C)
NPort® 5232I-T: 2-port RS-422/485 device server with 2 KV optical isolation, wide temperature (-40 to 75°C)
Optional Accessories (can be purchased separately)
DK-35A: Mounting Kit for 35-mm DIN-Rail
DIN-Rail Power Supply: See page A-8 for details
Terminal Block: See page A-7 for details
8-22
R+/D+
GND
Tx- / Data-
Tx+ / Data+
Rx-
Rx+
GND
RTS
CTS
Serial Device
TxD
Serial Device Servers > NPort® 5200 Series
Serial Device
Signals
I
T+
I
NPort 5232 /5232 -T
Signals
P2 RS-485/422
Tx+ / Data+
P1 RS-485/422
NPort 5232/5232-T
GND
T+
T-
GND
CTS
RTS
Tx
Rx
Signals
R-/D-
P2 RS-485/422
R+/D+
P1 RS-232
NPort 5232/5232-T
RxD
8
RS-232
RxD (in)
DCD (in)
CTS (in)
DTR (out)
T-
NPort® 5230/5230-T
(RS-232/422/485, terminal block connector)
PIN
5
6
7
8
T-
8
RS-232
DSR (in)
RTS (out)
Rx-
1
NPort® 5210/5210-T (RS-232)
Rx+
8-pin RJ45 connector
w w w. m o x a . c o m
info@moxa.com
Industrial Networking Solutions
NPort® 5400 Series
4-port RS-232/422/485 serial device servers
› Easy IP address configuration with LCD panel
› 10/100M auto-sensing Ethernet
› 4 serial ports, with support for RS-232, RS-422, and RS-485
› Built-in 15 KV ESD surge protection for all serial signals
› Versatile socket operation modes, including TCP Server, TCP
Client, and UDP
› Choice of configuration methods: Web console, Telnet console,
and Windows utility
› SNMP MIB-II for network management
› 2 KV isolation protection for NPort® 5430I
Network Readiness for up to Four Serial Devices
NPort® 5400 device servers can conveniently and transparently
connect up to four serial devices to an Ethernet, allowing you to
network your existing serial devices with only basic configuration.
Data transmission between the serial and Ethernet interfaces is
bi-directional. By using NPort® device servers, you not only protect
your current hardware investment, but also allow for future network
expansion. You can both centralize the management of your serial
devices, and distribute management hosts over the network.
Independent Operation Mode for each Serial Port
NPort® 5400 device servers can be used to connect different devices
for remote data polling, event handling, or data multicasting over
a TCP/IP network. Each serial port on the NPort® 5400 operates
independently to provide maximum versatility. For example, port 1 can
operate in Driver mode, port 2 in TCP Server mode, and ports 3 and 4
in TCP Client mode.
User-friendly LCD Panel for Easy Installation
Serial Device Servers > NPort® 5400 Series
The certification logos shown here apply to some or all of the products in this
section. Please see the Specifications section or Moxa’s website for details.
8
An LCD panel is built into the NPort® 5400’s top panel, with four
buttons for inputting data, configuration, and selecting the operation
mode. The LCD panel displays the server name, serial number, and IP
address, and can be used to enter or modify parameters such as IP
address, netmask, and gateway.
Redundant DC Power Inputs
NPort® 5400 device servers support redundant power sources and
provide both a DC terminal block input and a DC power jack input. The
two power inputs not only provide power redundancy, but also allow
greater flexibility for use with different applications.
Adjustable Termination and pull High/Low Resistors
Termination resistors may be needed in some critical environments
to prevent the reflection of serial signals. When using termination
resistors, it is important to set the pull high/low resistors correctly
to prevent the electrical signal from being corrupted. Since no set of
resistor values is universally compatible with all environments, the
NPort® 5400 has four sets of DIP switches on the bottom panel to set
the termination and pull high/low resistor values.
info@moxa.com
w w w. m o x a . c o m
8-23
Serial-to-Ethernet Solutions
Appearance
NPort® 5410
Power Input
Power Jack
(1 to 48 VDC)
8
NPort® 5430/5430I
Ethernet
RJ45 10/100 Mbps
Power Input
Terminal Block
(12 to 48 VDC)
Reset Button
LEDs
LAN and Serial Status
LCD Panel
DK-35A DIN-Rail Kit
Serial Device Servers > NPort® 5400 Series
Available Accessory
DB9 male
RS-422/485
DB9 male
Push Buttons
DIN-Rail or Panel mounting
Optional DIN-Rail (35 mm)
Mounting Kit
Specifications
Driver Support: Windows Real COM driver (for Windows 95, 98, ME,
NT, 2000, XP, 2003, Vista, XP x64, 2003 x64, Vista x64), Linux Real
TTY driver, Fixed TTY driver (for SCO Unix, SCO OpenServer,
UnixWare 7, UnixWare 2.1, SVR 4.2, QNX 4.25, QNX 6, Solaris 10,
FreeBSD, AIX 5.x, HP-UX 11i)
Ethernet Interface
Number of Ports: 1
Speed: 10/100 Mbps
Connector: 8-pin RJ45
Magnetic Isolation Protection: 1.5 KV built-in
Mini Screen with Push Buttons
Serial Interface
Number of Ports: 4
Serial Standards:
NPort® 5410: RS-232
NPort® 5430: RS-422/485
NPort® 5450: RS-232/422/485
Connectors:
NPort® 5410/5450: DB9 male
NPort® 5430: Terminal block
Serial Line Protection:
15 KV ESD protection for all signals
2 KV isolation protection (NPort® 5430I/5450I)
RS-485 Data Direction Control: ADDC® (automatic data direction
control)
Serial Communication Parameters
Serial Signals
RS-232: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
RS-422: Tx+, Tx-, Rx+, Rx-, GND
RS-485-4w: Tx+, Tx-, Rx+, Rx-, GND
RS-485-2w: Data+, Data-, GND
Physical Characteristics
Housing: SECC sheet metal (1 mm), providing IP30 protection
Weight: 740 g
Dimensions:
Without mounting kit: 158 x 103 x 33 mm (6.22 x 4.06 x 1.30 in)
With mounting kit: 176 x 103 x 33 mm (6.93 x 4.06 x 1.30 in)
Environmental Limits
Operating Temperature: 0 to 55°C (32 to 131°F)
Operating Humidity: 5 to 95% RH
Storage Temperature: -20 to 70°C (-4 to 158°F)
Power Requirements
Regulatory Approvals
Software
Network Protocols: ICMP, IP, TCP, UDP, DHCP, BOOTP, Telnet,
DNS, SNMP, HTTP, SMTP, SNTP, Rtelnet, ARP
Configuration Options: Web Console, Telnet Console, Windows
Utility
w w w. m o x a . c o m
LCD Panel: Liquid Crystal Display on the case
Push Buttons: Four push buttons for convenient on-site configuration
Input Voltage: 12 to 48 VDC
Power Consumption:
NPort® 5410/5430: 350 mA @ 12 V max.
NPort® 5430I: 585 mA @ 12 V max.
NPort® 5450: 350 mA @ 12 V max.
NPort® 5450I: 554 mA @ 12 V max.
Power Line Protection: 4 KV burst (EN61000-4-4: EFT/B), 2 KV
surge (EN61000-4-5)
Data Bits: 5, 6, 7, 8
Stop Bits: 1, 1.5, 2
Parity: None, Even, Odd, Space, Mark
Flow Control: DSR/DTR (RS-232 only), RTS/CTS, XON/XOFF
Baudrate: 50 bps to 921.6 Kbps
8-24
NPort® 5450/5450I
EMC: CE (EN55022 and EN55024 Class A), FCC Part 15 Subpart B
Class A
Safety: UL (UL60950-1), CUL, TÜV (EN60950-1)
Medical: EN60601-1-2 Class B, EN55011
Marine: DNV
info@moxa.com
Industrial Networking Solutions
Reliability
Warranty
Alert Tools: Built-in buzzer and RTC (real-time clock)
Automatic Reboot Trigger: Built-in WDT (watchdog timer)
MTBF (meantime between failures):
NPort® 5410: 205153 hrs
NPort® 5430: 201699 hrs
NPort® 5430I: 114540 hrs
Warranty Period: 5 years
Details: See www.moxa.com/warranty
Dimensions
RESET
V+ V-
33 mm
(1.3 in)
8
4 Port Device Server
P4
P3
Serial Device
Signals
NPort® 5450/5450I (RS-232/422/485, DB9 male connector)
(RS-232/422/485, DB9 male connector)
1 2 3 4 5
6 7 8 9
PIN
1
2
3
4
5
6
7
8
9
GND
R- / D-
NPort 5430/5430I
Terminal Block
RS-232
DCD
RxD
TxD
DTR
GND
DSR
RTS
CTS
RS-422/RS-485-4w
TxD-(A)
TxD+(B)
RxD+(B)
RxD-(A)
GND
---------
GND
6 7 8 9
T-
1 2 3 4 5
NPort® 5430/5430I
(RS-422/485, terminal block connector)
RS-232
DCD
RxD
RxD
DTR
GND
DSR
TRS
CTS
-
T+
PIN
1
2
3
4
5
6
7
8
9
Rx-
NPort® 5410
(RS-232, DB9 male connector)
Rx+
Pin Assignment
Tx- / Data-
158 mm (6.22 in)
169 mm (6.67 in)
181 mm (7.14 in)
158 mm (6.22 in)
169 mm (6.67 in)
R+ / D+
P2
P1
Serial Device Servers > NPort® 5400 Series
39 mm 25 mm
(1.54 in) (0.98 in)
103 mm (4.06 in)
LAN
35.5 mm
(1.4 in )
5410
Tx+ / Data+
O 3.2 mm
(0.13 in)
RS-485-2w
----Data+(B)
Data-(A)
GND
---------
Ordering Information
Available Models
Package Checklist
NPort® 5410: 4-port RS-232 device server
NPort® 5430: 4-port RS-422/485 device server
NPort® 5430I: 4-port RS-422/485 device server with 2 KV optical isolation
NPort® 5450: 4-port RS-232/422/485 device server
NPort® 5450I: 4-port RS-232/422/485 device server with 2 KV optical
isolation
UÊ
UÊ
UÊ
UÊ
UÊ
NPort® 5400 series device server
Power Jack to 3-pin Terminal Block Adaptor
Document and Software CD
Quick Installation Guide (printed)
Warranty Card
Optional Accessories (can be purchased separately)
DK-35A: Mounting Kit for 35-mm DIN-Rail
DIN-Rail Power Supply: See page A-8 for details
Terminal Block: See page A-7 for details
Power Adaptor: See page A-9 for details
info@moxa.com
w w w. m o x a . c o m
8-25
Serial-to-Ethernet Solutions
NPort® 5600 Rackmount Series
8 and 16-port RS-232/422/485 serial device servers
› 8 or 16 serial ports supporting RS-232/422/485
› Standard 19-inch rackmount size
› 10/100M auto-sensing Ethernet
› Built-in 15 KV ESD protection for all serial signals
› Easy IP address configuration with LCD panel
› Choice of configuration methods: Web console, Telnet console,
and Windows utility
› Versatile socket operation modes, including TCP Server, TCP
Client, UDP, and Real COM
› SNMP MIB-II for network management
8
Serial Device Servers > NPort® 5600 Rackmount Series
The certification logos shown here apply to some or all of the products in this
section. Please see the Specifications section or Moxa’s website for details.
Network Readiness for up to Sixteen Serial Devices
NPort® 5600 rackmount device servers can conveniently and
transparently connect up to sixteen serial devices to an Ethernet,
allowing you to network your existing serial devices with only basic
configuration. Data transmission between the serial and Ethernet
interfaces is bi-directional. By using NPort® device servers, you not
only protect your current hardware investment, but also allow for
future network expansion. You can both centralize the management
of your serial devices, and distribute management hosts over the
network.
19-inch Rackmount Device Server
NPort® 5600 device servers come with Tx/Rx LEDs for the serial ports
on the front panel, and the 8 or 16 RJ45 serial port connectors on the
rear panel. This makes the NPort® 5600 device servers suitable for
standard 19-inch rack mounting, allowing you to simplify operation,
maintenance, and administrative tasks.
Real COM/TTY Ports
Real COM/TTY drivers are provided that make the serial ports on the
NPort® 5600 recognizable as Real COM ports by Windows, or Real
TTY ports by Linux. In addition to supporting basic data transmission
and reception, the NPort® drivers also support the RTS, CTS, DTR,
DSR, and DCD control signals.
LED Indicators to Ease Your Maintenance Tasks
The System LED, Serial Tx/Rx LEDs, and Ethernet LEDs (located on the
RJ45 connector) provide a great tool for basic maintenance tasks and
help engineers analyze problems in the field. The NPort® 5600’s LEDs
not only indicate current system and network status, but also help field
engineers monitor the status of attached serial devices.
Adjustable Termination and Pull High/Low Resistors
In some critical environments, termination resistors may be needed
to prevent the reflection of serial signals. When using termination
resistors, it is also important to set the pull high/low resistors correctly
so that the electrical signal is not corrupted. Since no set of resistor
values is universally compatible for all environments, the NPort® 5600
has DIP switches on the bottom panel for setting the termination and
pull high/low resistor values.
8-26
w w w. m o x a . c o m
info@moxa.com
Industrial Networking Solutions
Appearance
AC Power Switch
Serial Ports (50 bps to 921.6 Kbps, RJ45 connectors)
NPort® 5610: RS-232
AC Power Input
100 to 240 VAC Input, 47
to 63 HZ
NPort® 5630: RS-422/485
Ethernet
NPort® 5650: RS-232/422/485
RJ45 10/100 Mbps
8
Push Buttons
Mounting Plate
LCD Panel
Connection Cable
RJ45 to DB9 Cable
(Optional Accessory)
Specifications
Ethernet Interface
Serial Communication Parameters
Number of Ports: 1
Speed: 10/100 Mbps
Connector: 8-pin RJ45
Magnetic Isolation Protection: 1.5 KV built-in
Data Bits: 5, 6, 7, 8
Stop Bits: 1, 1.5, 2
Parity: None, Even, Odd, Space, Mark
Flow Control: DSR/DTR and RTS/CTS (RS-232 only), XON/XOFF
Baudrate: 50 bps to 921.6 Kbps
Optical Fiber Interface
Distance:
Multi mode: 0 to 2 km, 1310 nm (62.5/125 µm, 500 MHz*km)
Single mode: 0 to 40 km, 1310 nm (9/125 µm, 3.5 PS/(nm*km))
Min. TX Output: -20 dBm (Multi mode), -5 dBm (Single mode)
Max. TX Output: -14 dBm (Multi mode), 0 dBm (Single mode)
Sensitivity: -34 to -30 dBm (Multi mode), -36 to -32 dBm (Single
mode)
Serial Interface
Number of Ports: 8 or 16
Serial Standards:
NPort® 5610: RS-232
NPort® 5630: RS-422/485
NPort® 5650: RS-232/422/485
Connectors: RJ45 (8 pins)
Serial Line Protection:
15 KV ESD protection for all signals
RS-485 Data Direction Control: ADDC® (automatic data direction
control)
Serial Signals
RS-232: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
RS-422: Tx+, Tx-, Rx+, Rx-, GND
RS-485-4w: Tx+, Tx-, Rx+, Rx-, GND
RS-485-2w: Data+, Data-, GND
Software
Network Protocols: ICMP, IP, TCP, UDP, DHCP, BOOTP, Telnet,
DNS, SNMP, HTTP, SMTP, SNTP, ARP, PPP, SLIP, RTelnet,
RFC2217
Configuration Options: Web Console, Telnet Console, Windows
Utility
Driver Support: Windows Real COM driver (for Windows 95, 98, ME,
NT, 2000, XP, 2003, Vista, XP x64, 2003 x64, Vista x64), Linux Real
TTY driver, Fixed TTY driver (for SCO Unix, SCO OpenServer,
UnixWare 7, UnixWare 2.1, SVR 4.2, QNX 4.25, QNX 6, Solaris 10,
FreeBSD, AIX 5.x, HP-UX 11i)
Serial Device Servers > NPort® 5600 Rackmount Series
LED Indicators
System Status,
Serial Tx/Rx
Reset Button
Mini Screen with Push Buttons
LCD Panel: Liquid Crystal Display on the case
Push Buttons: Four push buttons for convenient on-site configuration
info@moxa.com
w w w. m o x a . c o m
8-27
Serial-to-Ethernet Solutions
8
Physical Characteristics
Regulatory Approvals
Housing: SECC sheet metal (1 mm), providing IP30 protection
Weight:
NPort® 5610-8: 3340 g
NPort® 5610-8-48V: 3160 g
NPort® 5630-8: 3380 g
NPort® 5650-8: 3360 g
NPort® 5650-8-S-SC: 3380 g
NPort® 5650-8-M-SC: 3380 g
NPort® 5610-16: 3420 g
NPort® 5610-16-48V: 3260 g
NPort® 5630-16: 3400 g
NPort® 5650-16: 3460 g
NPort® 5650-16-S-SC: 3440 g
NPort® 5650-16-M-SC: 3440 g
Dimensions:
Without ears: 440 x 45 x 198 mm (17.32 x 1.77 x 7.80 in)
With ears: 480 x 45 x 198 mm (18.90 x 1.77 x 7.80 in)
EMC: CE (EN55022 Class A, EN55024), FCC Part 15 Subpart B
Class A
NPort® 5610 only: IEC61000-4-12
Safety: UL (UL60950-1), TÜV (EN60950-1)
Medical: EN60601-1-2 Class B, EN55011
Reliability
Automatic Reboot Trigger: Built-in WDT (watchdog timer)
MTBF (meantime between failures):
NPort® 5610-8: 97294 hrs
NPort® 5610-16: 94928 hrs
NPort® 5610-8-48V: 96758
NPort® 5610-16-48V: 94417 hrs
NPort® 5630-8: 118405 hrs
NPort® 5630-16: 91483 hrs
NPort® 5650-8: 117584 hrs
NPort® 5650-16: 104767 hrs
NPort® 5650-S-SC-8: 116914 hrs
NPort® 5650-S-SC-16: 87528 hrs
NPort® 5650-M-SC-8: 116914 hrs
NPort® 5650-M-SC-16: 87528 hrs
Environmental Limits
Warranty
Power Requirements
Warranty Period: 5 years
Details: See www.moxa.com/warranty
Input Voltage:
NPort® 5610/5630/5650: 100 to 240 VAC, 47 to 63 hz
NPort® 5610-48V: ±48 VDC (20 to 72 VDC, -20 to -72 VDC)
Power Consumption:
NPort® 5610-8/16: 141 mA @ 100 VAC, 93 mA @ 240 VAC
NPort® 5630-8/16: 152 mA @ 100 VAC, 98 mA @ 240 VAC
NPort® 5610-8/16-48V: 135 mA @ 48 VDC
NPort® 5650-8/16: 158 mA @ 100 VAC, 102 mA @ 240 VAC
NPort® 5650-8/16-S-SC: 164 mA @ 100 VAC, 110 mA @ 240 VAC
NPort® 5650-8/16-M-SC: 174 mA @ 100 VAC, 113 mA @ 240 VAC
Power Line Protection: 4 KV burst (EN61000-4-4: EFT/B), 2 KV
surge (EN61000-4-5)
Dimensions
5610-16
Serial ports
1
2
3
4
5
6
7
8
LA N
AC POWER 100-240V,47-63Hz
440 mm(17.3 in)
480 mm(19 in)
8-28
w w w. m o x a . c o m
info@moxa.com
9
10
11
12
13
14
15
16
45 mm
(1.77 in)
198 mm(7.8 in)
Serial Device Servers > NPort® 5600 Rackmount Series
Operating Temperature: 0 to 55°C (32 to 131°F)
Operating Humidity: 5 to 95% RH
Storage Temperature: -20 to 75°C (-4 to 167°F)
Industrial Networking Solutions
Pin Assignment
NPort® 5610
(RS-232, 8-port RJ45 connector)
NPort® 5630
(RS-422/485, 8-port RJ45 connector)
1
8
1
8
PIN
1
RS-232
DSR
PIN
RS-422/485-4w
1
---
2
3
RTS
GND
2
4
TXD
5
NPort® 5650
(RS-232/422/485, 8-port RJ45 connector)
1
8
RS-485-2w
PIN
RS-232
RS-422/485-4w
---
1
DSR
---
---
---
---
2
RTS
TxD+
---
3
TxD+
---
3
GND
GND
GND
4
TxD-
---
4
TXD
TxD-
---
RxD
5
RxD-
Data+
5
RxD
RxD+
Data+
6
DCD
6
RxD+
Data-
7
CTS
6
DCD
RxD-
Data-
8
DTR
7
GND
GND
7
CTS
---
---
8
---
---
8
DTR
---
---
RS-485-2w
Available Models
NPort® 5610-8: 8-port RS-232 rackmount device server with RJ45 connectors and 100-240 VAC power input
NPort® 5610-8-48V: 8-port RS-232 rackmount device server with RJ45 connectors and 48 VDC power input
NPort® 5630-8: 8-port RS-422/485 rackmount device server with RJ45 connectors and 100-240 VAC power input
NPort® 5650-8: 8-port RS-422/485 rackmount device server with RJ45 connectors and 100-240 VAC power input
NPort® 5650-8-M-SC: 8-port RS-232/422/485 rackmount device server with RJ45 connectors and 10/100BaseF(X) multi-mode fiber (SC connector)
NPort® 5650-8-S-SC: 8-port RS-232/422/485 rackmount device server with RJ45 connectors and 10/100BaseF(X) single-mode fiber (SC connector)
NPort® 5610-16: 16-port RS-232 rackmount device server with RJ45 connectors and 100-240 VAC power input
NPort® 5610-16-48V: 16-port RS-232 rackmount device server with RJ45 connectors and 48 VDC power input
NPort® 5630-16: 16-port RS-422/485 rackmount device server with RJ45 connectors and 100-240 VAC power input
NPort® 5650-16: 16-port RS-422/485 rackmount device server with RJ45 connectors and 100-240 VAC power input
NPort® 5650-16-M-SC: 16-port RS-232/422/485 rackmount device server with RJ45 connectors and 10/100BaseF(X) multi-mode fiber (SC
connector)
NPort® 5650-16-S-SC: 16-port RS-232/422/485 rackmount device server with RJ45 connectors and 10/100BaseF(X) single-mode fiber (SC
connector)
Optional Accessories (can be purchased separately)
Package Checklist
CBL-RJ45F25-150: 8-pin RJ45 to DB25 female cable, 150 cm
UÊ
UÊ
UÊ
UÊ
UÊ
UÊ
CBL-RJ45M25-150: 8-pin RJ45 to DB25 male cable, 150 cm
CBL-RJ45F9-150: 8-pin RJ45 to DB9 female cable, 150 cm
CBL-RJ45M9-150: 8-pin RJ45 to DB9 male cable, 150 cm
info@moxa.com
NPort® 5600 series device server
Power Cord (see Appendix A)
Serial cable for configuration
Document and Software CD
Quick Installation Guide (printed)
Warranty Card
w w w. m o x a . c o m
Serial Device Servers > NPort® 5600 Rackmount Series
Ordering Information
8
8-29
Serial-to-Ethernet Solutions
NPort® 5600 Desktop Series
8-port RS-232/422/485 serial device servers
› 8 serial ports supporting RS-232/422/485
› Compact desktop design
› 10/100M auto-detecting Ethernet
› Built-in 15 KV ESD protection for all serial signals
› Easy IP address configuration with LCD panel
› Choice of configuration methods: Web console, Telnet console,
and Windows utility
› Versatile socket operation modes, including TCP Server, TCP
8
Client, UDP, and Real COM
› SNMP MIB-II for network management
› Built-in recorder: Use your own voice as the alert when exceptions occur
Serial Device Servers > NPort® 5600 Desktop Series
The certification logos shown here apply to some or all of the products in this
section. Please see the Specifications section or Moxa’s website for details.
Introduction
NPort® 5600-8-DT device servers can conveniently and transparently
connect 8 serial devices to an Ethernet, allowing you to network
your existing serial devices with only basic configuration. You can
both centralize management of your serial devices and distribute
management hosts over the network.
Since the NPort® 5600-8-DT device servers have a smaller form factor
compared to our 19” models, they are a great choice for applications
that need additional serial ports, but for which mounting rails are not
available.
Convenient Design for RS-485 Applications
The NPort® 5650-8-DT device servers support selectable 1K-ohm and
150K-ohm pull high/low resistors and a 120-ohm terminator. In some
critical environments, termination resistors may be needed to prevent
the reflection of serial signals. When using termination resistors, it
is also important to set the pull high/low resistors correctly so that
the electrical signal is not corrupted. Since no set of resistor values
is universally compatible with all environments, NPort® 5600-8-DT
device servers use DIP switches to allow users to adjust termination
and pull high/low resistor values manually for each serial port.
Convenient Power Inputs
The NPort® 5650-8-DT device servers support both a power terminal
block and power jack for ease of use and greater flexibility. Users can
connect the terminal block directly to a DC power source, or use the
power jack to connect to an AC circuit through an adaptor.
LED Indicators to Ease Your Maintenance Tasks
The System LED, Serial Tx/Rx LEDs, and Ethernet LEDs (located on the
RJ45 connector) provide a great tool for basic maintenance tasks and
help engineers analyze problems in the field. The NPort® 5600’s LEDs
not only indicate current system and network status, but also help field
engineers monitor the status of attached serial devices.
Two Ethernet Ports for Convenient Cascade-style Wiring
The NPort® 5600-8-DT device servers come with two Ethernet ports
that can be used as Ethernet switch ports. Connect one port to the
network or server, and the other port to another Ethernet device. The
8-30
w w w. m o x a . c o m
dual Ethernet ports eliminate the need to connect each device to a
separate Ethernet switch, reducing wiring costs.
info@moxa.com
Industrial Networking Solutions
Automatic Warning Function by Speaker and/or E-mail
The built-in speakers can be used to alert administrators of problems
with the Ethernet links or power input. The web console indicates
which Ethernet link or power input has failed. An e-mail warning can
also be issued when an exception is detected. These functions are
valuable tools that enable maintenance engineers to react promptly to
emergency situations.
Appearance
LCD Panel
Push Buttons
LED Indicators
Power Input
Both power Jack
and Terminal block
12-48VDC
Serial Ports
NPort® 5610-8-DT: DB9, RS-232
RS-232 Console Port
NPort® 5650-8-DT: DB9, RS-232/422/485
Reset Button
NPort® 5610-8-DT-J: RJ45, RS-232
NPort® 5650-8-DT-J: RJ45, RS-232/422/485
Specifications
Ethernet Interface
Serial Communication Parameters
Number of Ports: 2
Speed: 10/100 Mbps
Connector: 8-pin RJ45
Magnetic Isolation Protection: 1.5 KV built-in
Data Bits: 5, 6, 7, 8
Stop Bits: 1, 1.5, 2
Parity: None, Even, Odd, Space, Mark
Flow Control: DSR/DTR and RTS/CTS (RS-232 only), XON/XOFF
Baudrate: 50 bps to 921.6 Kbps
Serial Interface
Number of Ports: 8
Serial Standards:
NPort® 5610-8-DT: RS-232
NPort® 5650-8-DT: RS-232/422/485
Connectors:
NPort® 5610-8-DT/5650-8-DT/5650I-8-DT: DB9 male
NPort® 5610-8-DT-J/5650-8-DT-J: RJ45 (8 pins)
Serial Line Protection:
15 KV ESD protection for all signals
2 KV isolation protection (NPort® 5650I-8-DT only)
RS-485 Data Direction Control: ADDC® (automatic data direction
control)
Serial Device Servers > NPort® 5600 Desktop Series
Ethernet Switch
RJ45 10/100 Mbps
8
Serial Signals
RS-232: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
RS-422: Tx+, Tx-, Rx+, Rx-, GND
RS-485-4w: Tx+, Tx-, Rx+, Rx-, GND
RS-485-2w: Data+, Data-, GND
Software
Network Protocols: ICMP, IP, TCP, UDP, DHCP, BOOTP, Telnet,
DNS, SNMP, HTTP, SMTP, SNTP, Rtelnet, ARP, RFC2217
Configuration Options: Web Console, Telnet Console, Windows
Utility
Driver Support: Windows Real COM driver (for Windows 95, 98, ME,
NT, 2000, XP, 2003, Vista, XP x64, 2003 x64, Vista x64), Linux Real
TTY driver, Fixed TTY driver (for SCO Unix, SCO OpenServer,
UnixWare 7, UnixWare 2.1, SVR 4.2, QNX 4.25, QNX 6, Solaris 10,
FreeBSD, AIX 5.x, HP-UX 11i)
info@moxa.com
w w w. m o x a . c o m
8-31
Serial-to-Ethernet Solutions
Mini Screen with Push Buttons
Power Requirements
LCD Panel: Liquid Crystal Display on the case
Push Buttons: Four push buttons for convenient on-site configuration
Input Voltage: 12 to 48 VDC
Power Consumption:
NPort® 5610-8-DT: 621 mA @ 12 V, 140 mA @ 48 V
NPort® 5610-8-DT-J: 621 mA @ 12 V, 140 mA @ 48 V
NPort® 5650-8-DT: 580 mA @ 12 V, 156 mA @ 48 V
NPort® 5650I-8-DT: 1066 mA @ 12 V, 200 mA @ 48 V
NPort® 5650-8-DT-J: 580 mA @ 12 V, 156 mA @ 48 V
Physical Characteristics
Environmental Limits
Regulatory Approvals
EMC: CE (EN55022 Class A, EN55024), FCC Part 15 Subpart B
Class A
Safety: UL (UL60950-1), TÜV (EN60950-1)
Reliability
Alert Tools: Built-in buzzer and RTC (real-time clock)
Automatic Reboot Trigger: Built-in WDT (watchdog timer)
Warranty
Warranty Period: 5 years
Details: See www.moxa.com/warranty
Dimensions
5650-B-DT
44 mm
Serial Device Servers > NPort® 5600 Desktop Series
Operating Temperature: 0 to 55°C (32 to 131°F)
Operating Humidity: 5 to 95% RH
Storage Temperature: -20 to 70°C (-4 to 158°F)
125 mm
25 mm
50 mm
8
Housing: SECC sheet metal (0.8 mm), providing IP30 protection
Weight:
NPort® 5610-8-DT: 1760 g
NPort® 5610-8-DT-J: 1170 g
NPort® 5650-8-DT: 1770 g
NPort® 5650-8-DT-J: 1710 g
NPort® 5650I-8-DT: 1850 g
Dimensions:
Without ears: 197 x 44 x 135.5 mm (7.76 x 1.73 x 5.33 in)
With ears: 229 x 46 x 135.5 mm (9.01 x 1.81 x 5.33 in)
With DIN-Rail kit on bottom panel: 197 x 53 x 135.5 mm (7.76 x 2.09
x 5.33 in)
197 mm
209 mm
229 mm
Pin Assignment
DB9 male connector
1 2 3 4 5
6 7 8 9
8-pin RJ45 connector
1
8-32
8
NPort® 5610-8-DT (RS-232)
NPort® 5650-8-DT/5650I-8-DT (RS-232/422/485)
PIN
RS-232
PIN
RS-232
RS-422/485-4w
RS-485-2w
1
DCD
1
DCD
TxD-(A)
–
2
RxD
2
RxD
TxD+(B)
–
3
TxD
3
TxD
RxD+(B)
Data+(B)
4
DTR
4
DTR
RxD-(A)
Data-(A)
5
GND
5
GND
GND
GND
6
DSR
6
DSR
–
–
7
RTS
7
RTS
–
–
8
CTS
8
CTS
–
–
NPort® 5610-8-DT-J (RS-232)
PIN
RS-232
1
DCD
2
RxD
3
TxD
4
DTR
5
GND
6
DSR
7
RTS
8
CTS
w w w. m o x a . c o m
NPort® 5650-8-DT-J (RS-232/422/485)
PIN
1
2
3
4
5
6
7
8
info@moxa.com
RS-232
DSR
RTS
GND
TXD
RxD
DCD
CTS
DTR
RS-422/485-4w
--TxD+
GND
TxDRxD+
RxD-----
RS-485-2w
----GND
--Data+
Data-----
Industrial Networking Solutions
Ordering Information
Available Models
NPort® 5610-8-DT: 8-port RS-232 desktop device server with DB9 male connectors and 48 VDC power input
NPort® 5610-8-DT-J: 8-port RS-232 desktop device server with RJ45 connectors and 48 VDC power input
NPort® 5650-8-DT: 8-port RS-232/422/485 desktop device server with DB9 male connectors and 48 VDC power input
NPort® 5650I-8-DT: 8-port RS-232/422/485 desktop device server with DB9 male connectors, 48 VDC power input, and 2 KV optical isolation
NPort® 5650-8-DT-J: 8-port RS-232/422/485 desktop device server with RJ45 connectors and 48 VDC power input
Optional Accessories (can be purchased separately)
Package Checklist
CBL-RJ45F25-150: 8-pin RJ45 to DB25 female cable, 150 cm
UÊ
UÊ
UÊ
UÊ
UÊ
CBL-RJ45M25-150: 8-pin RJ45 to DB25 male cable, 150 cm
CBL-RJ45F9-150: 8-pin RJ45 to DB9 female cable, 150 cm
CBL-RJ45M9-150: 8-pin RJ45 to DB9 male cable, 150 cm
NPort® 5600 series device server
Power Adaptor (see Appendix A)
Document and Software CD
Quick Installation Guide (printed)
Warranty Card
8
Serial Device Servers > NPort® 5600 Desktop Series
info@moxa.com
w w w. m o x a . c o m
8-33
Serial-to-Ethernet Solutions
NPort® IA5000 Series
1 and 2-port serial device servers for industrial automation
› Versatile socket operation modes, including TCP Server, TCP
Client, UDP
› Patented ADDC® (automatic data direction control) for 2-wire
and 4-wire RS-485
› Cascading Ethernet ports for easy wiring (applies only to RJ45
connectors)
› Redundant DC power inputs
› Warning by relay output and e-mail
› 10/100BaseTX (RJ45) or 100BaseFX (single mode or multimode with SC connector)
› IP30-rated housing
8
Serial Device Servers > NPort® IA5000 Series
The certification logos shown here apply to some or all of the
products in this section. Please see the Specifications section
or Moxa’s website for details.
Overview
NPort® IA device servers provide easy and reliable serial-to-Ethernet
connectivity for industrial automation applications. The device servers
can connect any serial device to an Ethernet network, and to ensure
compatibility with network software, they support a variety of port
operation modes, including TCP Server, TCP Client, and UDP. The
rock-solid reliability of the NPort® IA device servers makes them
an ideal choice for establishing network access to RS-232/422/485
serial devices such as PLCs, sensors, meters, motors, drives, barcode
readers, and operator displays. All models are housed in a compact,
rugged housing that is DIN-rail mountable.
Cascading Ethernet Ports Make Wiring Easy (10/100BaseTX models only)
The NPort® IA5150 and IA5250 device servers each have two Ethernet
ports that can be used as Ethernet switch ports. One port connects
directly to the network or server, and the other port can be connected
to another NPort® IA device server or another Ethernet device. The
8-34
w w w. m o x a . c o m
dual Ethernet ports help reduce wiring costs by eliminating the need to
connect each device to a separate Ethernet switch.
info@moxa.com
Industrial Networking Solutions
Redundant Power Inputs
The NPort® IA5000 device servers have two power inputs that can
be connected simultaneously to live DC power sources. If one power
source fails, the other source takes over automatically. Redundant
power inputs help assure non-stop operation of your device server.
Dual Power Inputs
Power Failure Alarm
8
Relay Output Warning and E-mail Alerts
Optical Fiber for Ethernet Communication
The NPort® IA5000 series includes 100BaseFX fiber models that
support transmission distances up to 2 km for multi-mode models,
and up to 40 km for single-mode models. Optical fiber is well-suited
for industrial applications because it is immune to electromagnetic
noise and interference. For environments that experience high ground
loop voltages, fiber provides the best isolation protection, and because
there is no danger of sparking, optical fiber is safer than copper wire to
use in hazardous environments.
Industrial-grade Certification
To ensure safe and reliable operation in industrial environments,
the NPort® IA5000 device servers have obtained various industrial
certifications, including an IP30 rating for mechanical protection,
UL508 safety certification for industrial control equipment, and
Serial Device Servers > NPort® IA5000 Series
The built-in relay output can be used to alert administrators of
problems with the Ethernet links or power inputs, or when there is a
change in the DCD or DSR serial signals. The web console indicates
which Ethernet link or power input has failed, or which serial signal
has changed. An e-mail warning can also be issued when an exception
is detected. These functions are valuable tools that enable maintenance
engineers to react promptly to emergency situations.
explosion-safe certifications for hazardous locations.
Certifications include UL/cUL Class 1 Division 2 Groups A,
B, C, D, and ATEX Class 1 Zone 2.
Appearance
Dual Power Input and
Relay Output
Reset
Reset
LED
Indicators
RS-422/485
RS-232
1-port
Copper
Ethernet
Fiber optic
Ethernet
RS-232/422/485
2-port
info@moxa.com
w w w. m o x a . c o m
8-35
Serial-to-Ethernet Solutions
Specifications
RS-422: Tx+, Tx-, Rx+, Rx-, GND
RS-485-4w: Tx+, Tx-, Rx+, Rx-, GND
RS-485-2w: Data+, Data-, GND
Ethernet Interface (NPort® IA5150/5150I/5250)
Number of Ports: 2
Speed: 10/100 Mbps, Auto MDI/MDIX
Connector: 8-pin RJ45
Magnetic Isolation Protection: 1.5 KV built-in
Software
Optical Fiber Interface (NPort® IA5150-M-SC/5150IM-SC/5150-S-SC/5150I-S-SC)
8
Fiber Port: 100 BaseFX, SC connector
Distance:
Multi mode: 0 to 2 km, 1310 nm (62.5/125 µm, 500 MHz*km)
Single mode: 0 to 40 km, 1310 nm (9/125 µm, 3.5 PS/(nm*km))
Min. TX Output: -20 dBm (Multi mode), -5 dBm (Single mode)
Max. TX Output: -14 dBm (Multi mode), 0 dBm (Single mode)
Sensitivity: -34 to -30 dBm (Multi mode), -36 to -32 dBm (Single
mode)
Serial Device Servers > NPort® IA5000 Series
Serial Interface
Number of Ports:
NPort® IA5150: 1
NPort® IA5250: 2
Serial Standards: RS-232/422/485
Connectors:
NPort® IA5150: 8-pin RJ45 for RS-232, Terminal Block for
RS-422/485
NPort® IA5250: Terminal Block (5 terminals per port)
ESD Protection: 15 KV for all signals
Optical Isolation Protection: 2 KV (NPort® IA5150I, NPort®
5150I-M-SC, NPort® 5150I-S-SC)
RS-485 Data Direction Control: ADDC® (automatic data direction
control)
Serial Communication Parameters
Data Bits: 5, 6, 7, 8
Stop Bits: 1, 1.5, 2
Parity: None, Even, Odd, Space, Mark
Flow Control: RTS/CTS (RS-232 only), XON/XOFF
Baudrate: 110 bps to 230.4 Kbps
RS-232:
NPort® IA5150: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
NPort® IA5250: TxD, RxD, RTS, CTS, GND
Pin Assignment
1 2 3 4 5
6 7 8 9
PIN
RS-232
RS-422/RS-485-4w
1
DCD
TxD-(A)
–
2
RXD
TxD+(B)
–
3
TXD
RxD+(B)
Data+(B)
4
DTR
RxD-(A)
Data-(A)
5
GND
GND
GND
6
DSR
–
–
7
RTS
–
–
8
CTS
–
–
RS-422/485 Terminal
Block Wiring
5
8-36
4
3
2
1
Physical Characteristics
Housing: IP30 protection
Weight:
NPort® IA5150: 360 g
NPort® IA5250: 380 g
Dimensions: 29 x 89.2 x 118.5 mm (0.82 x 3.51 x 4.57 in)
Environmental Limits
Operating Temperature:
NPort® IA5150/5250: 0 to 55°C (32 to 131°F)
NPort® IA5150-T/5250-T: -40 to 75°C (-40 to 167°F)
Operating Humidity: 5 to 95% RH
Storage Temperature: -20 to 85°C (-4 to 185°F)
Power Requirements
Input Voltage: 12 to 48 VDC
Power Consumption:
NPort® IA5150: 360 mA @ 12V max.
NPort® IA5150I: 420 mA @ 12V max.
NPort® IA5250: 440 mA @ 12V max.
NPort® IA5150-S-SC: 470 mA @ 12V max.
NPort® IA5150I-S-SC: 490 mA @ 12V max.
NPort® IA5150-M-SC: 500 mA @ 12V max.
NPort® IA5150I-M-SC: 510 mA @ 12V max.
Regulatory Approvals
Serial Signals
RS-232/422/485
DB9 male port
Network Protocols: ICMP, IP, TCP, UDP, DHCP, BOOTP, Telnet,
Rtelnet, DNS, SNMP, HTTP, SMTP, SNTP
Configuration Options: Web Console, Serial Console, Telnet Console,
Windows Utility
Driver Support: Windows Real COM driver (for Windows 95, 98, ME,
NT, 2000, XP, 2003, Vista, XP x64, 2003 x64, Vista x64), Linux Real
TTY driver, Fixed TTY driver (for SCO Unix, SCO OpenServer,
UnixWare 7, UnixWare 2.1, SVR 4.2, QNX 4.25, QNX 6, Solaris 10,
FreeBSD, AIX 5.x, HP-UX 11i)
RS-485-2W
Safety: UL60950 (E212360), UL 508, CSA C22.2 No. 60950,
EN60950
Hazardous Location: UL/cUL Class I, Division 2,
Groups A, B, C and D (E238559) (pending)
ATEX: Class I, Zone 2, EEx nC IIC (03CA24537) (pending)
Marine: DNV
EMI: FCC Part 15, CISPR (EN55022) Class A
EMS:
EN61000-4-2 (ESD), Level 3
EN61000-4-3 (RS), Level 3
EN61000-4-4 (EFT), Level 4
EN61000-4-5 (Surge), Level 3
EN61000-4-6 (CS), Level 3
EN61000-4-8
EN61000-4-11
EN61000-4-12
Shock: IEC60068-2-27
Freefall: IEC60068-2-32
Vibration: IEC60068-2-6
Dust-proof: IP30
PIN
RS-422/RS-485-4w
RS-485-2w
1
TxD+(B)
–
2
TxD-(A)
–
3
RxD+(B)
Data+(B)
Warranty
4
RxD-(A)
Data-(A)
5
GND
GND
Warranty Period: 5 years
Details: See www.moxa.com/warranty
w w w. m o x a . c o m
info@moxa.com
Industrial Networking Solutions
Dimensions
20.6 mm 29.91 mm
(0.81 in) (1.18 in)
NPort IA5150I-S-SC
NPort IA5150
NPort IA5150I-M-SC
NPort IA5150I
NPort IA5150-S-SC
NPort IA5250
NPort IA5150-M-SC
29 mm (1.14 in)
11.5 mm
(0.45 in)
29 mm (1.14 in)
NPort IA5250
25.9 mm 35 mm
(1.02 in) (1.38 in)
Ordering Information
Available Models
NPort® IA5150: 1-port RS-232/422/485 device server with 2 10/100BaseT(X) ports (RJ45 connectors, single IP)
NPort® IA5150-T: 1-port RS-232/422/485 device server with 2 10/100BaseT(X) ports (RJ45 connectors, single IP), wide temperature (-40 to 75°C)
NPort® IA5150I: 1-port RS-232/422/485 device server with 2 10/100BaseT(X) ports (RJ45 connectors, single IP) and 2 KV optical isolation
NPort® IA5150I-T: 1-port RS-232/422/485 device server with 2 10/100BaseT(X) ports (RJ45 connectors, single IP) and 2 KV optical isolation, wide
temperature (-40 to 75°C)
NPort® IA5150-M-SC: 1-port RS-232/422/485 device server with 2 10/100BaseF(X) multi-mode fiber (SC connectors) ports
NPort® IA5150-M-SC-T: 1-port RS-232/422/485 device server with 2 10/100BaseF(X) multi-mode fiber (SC connectors) ports, wide temperature
(-40 to 75°C)
NPort® IA5150I-M-SC: 1-port RS-232/422/485 device server with 2 10/100BaseF(X) multi-mode fiber (SC connectors) ports and 2 KV optical
isolation
NPort® IA5150I-M-SC-T: 1-port RS-232/422/485 device server with 2 10/100BaseF(X) multi-mode fiber (SC connectors) ports and 2 KV optical
isolation, wide temperature (-40 to 75°C)
NPort® IA5150-S-SC: 1-port RS-232/422/485 device server with 2 10/100BaseF(X) single-mode fiber (SC connectors) ports
NPort® IA5150-S-SC-T: 1-port RS-232/422/485 device server with 2 10/100BaseF(X) single-mode fiber (SC connectors) ports, wide temperature
(-40 to 75°C)
NPort® IA5150I-S-SC: 1-port RS-232/422/485 device server with 2 10/100BaseF(X) single-mode fiber (SC connectors) ports and 2 KV optical
isolation
NPort® IA5150I-S-SC-T: 1-port RS-232/422/485 device server with 2 10/100BaseF(X) single-mode fiber (SC connectors) ports and 2 KV optical
isolation, wide temperature (-40 to 75°C)
NPort® IA5250: 2-port RS-232/422/485 device server with 2 10/100BaseT(X) ports (RJ45 connectors, single IP)
NPort® IA5250-T: 2-port RS-232/422/485 device server with 2 10/100BaseT(X) ports (RJ45 connectors, single IP), wide temperature (-40 to 75°C)
Optional Accessories (can be purchased separately)
Package Checklist
Optical Fiber Patch Cord: See page A-14
UÊ
UÊ
UÊ
UÊ
Terminal Block for RS-422/485 ports: See page A-7
Power Jack to Terminal Block Cable: See page A-7
info@moxa.com
8
Serial Device Servers > NPort® IA5000 Series
25.9 mm 35 mm
(1.02 in) (1.38 in)
NPort IA5150
NPort IA5150 I
NPort IA5150-S-SC
NPort IA5150-M-SC
NPort IA5150 I -S-SC
NPort IA5150 I -M-SC
14.5 mm
(0.57 in)
89.2 mm (3.51 in)
118.5 mm (4.67 in)
20 mm
(0.79 in)
66.6 mm (2.62 in)
79.5 mm (3.13 in)
92.4 mm (3.64 in)
69.5 mm (2.74 in)
14.5 mm
(0.57 in)
124.5 mm (4.9 in)
14.5 mm
(0.57 in)
NPort IA series device server
Document and Software CD
Quick Installation Guide (printed)
Warranty Card
w w w. m o x a . c o m
8-37
Serial-to-Ethernet Solutions
NE-4100 Series
10/100 Mbps embedded serial device servers
NE-4110S/4110A
8
NE-4120S/4120A
› 10/100 Mbps Ethernet interface
› Up to 230.4 Kbps baudrate support
› Choice of operation modes: Real COM, TCP Server, TCP Client,
and UDP
› DHCP, BootP, Static IP, and ARP supported
› SNMP and e-mail alerts for event trapping and notification
› Half the size of a credit card—only 57 × 40 mm
› Low power consumption at 1.5W, with single +5V input
The certification logos shown here apply to some or all of the products in this
section. Please see the Specifications section or Moxa’s website for details.
NE-4100T
Serial Device Servers > NE-4100 Series
Overview
Moxa’s NE-4100 embedded device servers are designed for
manufacturers who want to add sophisticated network connectivity
to their serial devices. Moxa’s embedded device servers can be used
to convert any device with a standard serial interface to an Ethernetenabled device in no time. The NE-4100 embedded device servers
support 10/100 Mbps Ethernet, and provide ready-to-use operation
modes, including TCP Server, TCP Client, and UDP. In addition, a
Real COM driver is included for backward compatibility with legacy
software.
SNMP and E-mail Alerts for Event Trap and Notification
NE-4100 embedded device servers can be configured to send an
SNMP trap or e-mail under the following conditions:
UÊ Cold/warm start
UÊ Password authentication failure
UÊ Change in DSR/DCD line signal
UÊ Change in IP address
UÊ Change in password
On-site Configuration with Serial Command Mode
UÊ
UÊ
UÊ
UÊ
UÊ
Easy on-site configuration of network settings
Simple command frame format
Comprehensive command set for serial and network configuration
Easily switch between software and hardware triggers
Software reset
Typical Installation Examples
NE-4110: RJ45 Ethernet connector in
stand-alone form factor
8-38
NE-4120: Pin-header Ethernet in
stand-alone form factor
w w w. m o x a . c o m
info@moxa.com
NE-4100T: Dual-in-line pin header in
drop-in form factor
Industrial Networking Solutions
Powerful, User-friendly Utilities
Web-based Configuration
settings over the network. This utility has the following useful features:
NE-4100 embedded device servers can be configured with the
web console, which can be accessed from the web browser of any
networked computer.
UÊ
UÊ
UÊ
UÊ
Search your LAN for embedded device servers
Export and import configuration parameters
Upgrade firmware over the network
Remotely monitor data traffic, serial line status,
and TCP/IP connections
UÊ Configure SNMP and e-mail alerts
8
Search for installed
embedded device servers
Configure and manage embedded device servers with
Moxa’s Windows Utility
Serial Device Servers > NE-4100 Series
System log for cold boot,
warm boot, etc.
Remotely configure serial, network, alarm,
and other parameters
Network Enabler Administrator is a powerful, Windows-based
configuration and management tool for NE-4100 embedded device
servers. With Network Enabler Administrator, users can modify IP
addresses, update communication parameters, and configure all other
NE-4100 Starter Kit
The Network Enabler Starter Kit includes an evaluation board, power
adaptor, software, and serial and Ethernet cables to allow quick
and easy evaluation of all embedded device server functions. The
evaluation board is equipped with serial, Ethernet, digital I/O, and
power circuits to help you test your modules and applications.
Cross-over
Ethernet Cable
Null Modem Cable
Document & Software CD
Power Cord
(US or Euro plug)
Power Adaptor (90 to
240 VAC, 12 VDC)
Application Board
Dimensions and Pin Assignment
NE-4120S/4120A
57 mm (2.24 in)
57 mm (2.24 in)
45 mm (1.77 in)
45 mm (1.77 in)
J1
RJ45
CN
16-bit
Micro
Processor
PIN
1
2
3
6
8
Signals
Tx+
TxRx+
Rx-
34 mm (1.34 in)
J2
1
40 mm (1.57 in)
40 mm (1.57 in)
34 mm (1.34 in)
NE-4110S/4110A
info@moxa.com
J3
Ethernet
Pin-header
J2
J3
J1
16-bit
Micro
Processor
w w w. m o x a . c o m
1
Tx+
2
Tx-
3
4
Rx+
5
Rx-
8-39
Serial-to-Ethernet Solutions
NE-4110/4120 Series
NE-4110S/4120S
NE-4110A/4120A
J1
J1
J2
DIO0 10 9
10M_LED
DIO1 8
7
100M_LED
NC 10
CTS0 8
DSR0 6
DTR0 4
DIO2 6
5
Ready_LED
RxD0 2
DIO3 4
3
Reset
TxD1 2
1
RxD1
GND 14 13 VCC(+5V)
GND 12 11 VCC(+5V)
9 NC
7 RTS0
1 DCD0
5 GND
3 TxD0
NC 10 9
NC 8 7
NC 6 5
RxD- (Data-) 4
TxD+ 2
NC
For 2-wire RS-485
mode, Pin 3 is Data+,
Pin 4 is Data-
NC
GND
3
RxD+ (Data+)
1
TxD-
NE-4110T
Serial Device Servers > NE-4100 Series
Signal
ETx+
ETxERx+
ERxLED 10M
TxD0
RxD0
RTS0
CTS0
Reset
GND
GND
TxD1
Pin No.
14
15
16
17
18
19
20
21
22
23
24
25
26
36 mm (1.42 in)
8
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
45 mm (1.77 in)
Specifications
Form Factor
Serial Communication Parameters
Type:
NE-4110/4120: Ready-to-go stand-alone modules
NE-4100T: 26-pin dual-in-line package
Dimensions:
NE-4110/4120: 57 × 40 mm (2.24 x 1.57 in)
NE-4100T: 45 × 36 mm (1.77 x 1.42 in)
Data Bits: 5, 6, 7, 8
Stop Bits: 1, 1.5, 2
Parity: None, Even, Odd, Space, Mark
Flow Control: RTS/CTS, XON/XOFF
Baudrate: 110 bps to 230.4 Kbps
Serial Signals
Ethernet Interface
RS-232: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
RS-422: Tx+, Tx-, Rx+, Rx-, GND
RS-485-4w: Tx+, Tx-, Rx+, Rx-, GND
RS-485-2w: Data+, Data-, GND
TTL (Port 1): TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
TTL (Port 2): TxD, RxD, GND
Digital I/O Pins
GPIO: 4 programmable I/O pins
Number of Ports: 1
Speed: 10/100 Mbps, Auto MDI/MDIX
Connectors:
NE-4110 Series: RJ45
NE-4120 Series: 5-pin pin header
NE-4100T: 26-pin dual-in-line
Magnetic Isolation Protection: 1.5 KV built-in
Serial Interface
Number of Ports: 2
Serial Standards for Port 1:
NE-4110S/4120S: RS-232
NE-4110A/4120A: RS-422, RS-485-4w, RS-485-2w
NE-4100T: TTL
Serial Standards for Port 2:
TTL console port
RS-485 Flow Control: ADDC® (automatic data direction control)
8-40
Signal
PIO0
PIO1
PIO2
PIO3
LED 100M
DCD0
DSR0
DTR0
GND
Ready LED
+5V
(45 × 36 mm, 26-pin DIL package,
+5V
2.54 mm pitch)
RxD1
w w w. m o x a . c o m
Software
Network Protocols: ICMP, ARP, IP, TCP, UDP, DHCP, Telnet, HTTP,
SNMP, SMTP
Configuration Options: Web Console, Serial Console, Telnet Console,
Windows Utility
Driver Support: Windows Real COM driver (for Windows 95, 98, ME,
NT, 2000, XP, 2003, XP x64, 2003 x64), Linux Real TTY driver, Unix
info@moxa.com
Industrial Networking Solutions
Environmental Limits
Operating Temperature:
Standard Models: 0 to 55°C (32 to 131°F)
Wide Temperature (T) Models: -40 to 75°C (-40 to 167°F)
Operating Humidity: 5 to 95% RH
Storage Temperature: -20 to 70°C (-4 to 158°F)
Power Requirements
Input Voltage: 5 VDC (±5%)
Power Consumption: 290 mA @ 5 VDC max.
Regulatory Approvals
EMC: CE (Class A), FCC (Class A)
Reliability
Automatic Reboot Trigger: Built-in WDT (watchdog timer)
Warranty
Warranty Period: 5 years
Details: See www.moxa.com/warranty
Ordering Information
Package Checklist (modules)
NE-4110S: Device server module for RS-232 devices, supports 10/100BaseT(x) with
RJ45 connector
NE-4110A: Device server module for RS-422/485 devices, supports 10/100BaseT(x)
with RJ45 connector
NE-4120S: Device server module for RS-232 devices, supports 10/100BaseT(x) with
5-pin Ethernet pin header
NE-4120A: Device server module for RS-422/485 devices, supports 10/100BaseT(x)
with 5-pin Ethernet pin header
NE-4100T: Device server module for TTL devices, supports 10/100BaseT(x) with
DIL package
NE-4110-ST: Starter kit for the NE-4110S and NE-4110A
NE-4120-ST: Starter kit for the NE-4120S and NE-4120A
NE-4100-ST: Starter kit for the NE-4100T
UÊ NE-4100 series module
info@moxa.com
Package Checklist (starter kits)
UÊ NE-4100 series module
UÊ NE-4100-ST or NE-4110-ST or
NE-4120-ST evaluation board
UÊ Universal power adaptor
UÊ 2 power cords
UÊ Null modem cable
UÊ Cross-over Ethernet cable
UÊ Document and Software CD
UÊ Quick Installation Guide (printed)
UÊ Warranty Card
w w w. m o x a . c o m
8
Serial Device Servers > NE-4100 Series
Available Models
8-41
Serial-to-Ethernet Solutions
WE-2100T Series
Wireless LAN embedded serial device servers
› Connects serial devices to IEEE 802.11a/b/g networks
› Choice of operation modes: Real COM, TCP Server, TCP Client,
UDP, and RFC2217
› Windows (including Vista!) real COM and Linux fixed TTY
drivers provided
› Wireless security with WEP, WPA, and WPA2
› Select Any Baudrate between 50 bps and 921.6 Kbps
› 9 programmable digital I/O channels
› SSL/SSH encryption for configuration
› Compact size and easily mounted housing
8
Serial Device Servers > WE-2100T Series
The certification logos shown here apply to some or all of the
products in this section. Please see the Specifications section
or Moxa’s website for details.
Overview
The WE-2100T is a secure and compact embedded
embed
wireless module
for connecting serial devices to access points in infrastructure mode,
or to other WE-2100T’s in ad-hoc mode. When using the WE-2100T,
complex RF know-how is not needed to connect serial devices to
a wireless Ethernet network. Encryption for secure data transfer is
supported, along with the 802.11a/b/g radio specifications.
Operation Modes for Embedded Applications
The WE-2100T supports Real COM, TCP Server, TCP Client, UDP,
and RFC 2217 operation modes, which are designed to fulfill the
requirements of embedded module applications. Complete driver
support for Real COM mode is included and easy to install.
On-site Configuration with Serial Command Mode
UÊ Easy on-site configuration of network settings
UÊ Simple command frame format
UÊ Comprehensive command set for serial and network configuration
UÊ Easily switch between software and hardware triggers
UÊ Software reset
Specifications
Form Factor
Type: Small metal housing that encloses advanced ARM-based 32-bit
processor; supports both wireless and Ethernet connections
Dimensions: 54 x 40 x 13.3 mm (2.13 x 1.57 x 0.52 in)
Automatic Network Selection
Wireless or Ethernet: The WE-2100T will activate the Ethernet
connection if detected at boot-up. If an Ethernet connection is not
detected, the WE-2100T will choose wireless as the communication
interface. Which interface to use can also be configured with the
WE-2100T’s configuration utilities.
Ethernet Interface
Number of Ports: 1
Speed: 10/100 Mbps, Auto MDI/MDIX
Connector: 44-pin dual-in-line
Magnetic Isolation Protection: 1.5 KV built-in
WLAN Interface
Standard Compliance: IEEE 802.11a/b/g
Network Mode: Infrastructure mode (a/b/g), Ad-Hoc mode (b/g)
Spread Spectrum Technology: DSSS, CCK, OFDM
8-42
w w w. m o x a . c o m
5.15 to 5.25 GHz: 15 dBm @ 6 Mbps; 12 dBm @ 54 Mbps 5.725 to
5.825 GHz: 15 dBm @ 6 Mbps; 12 dBm @ 54 Mbps
2.412 to 2.483 GHz: 17 dBm @ 6 Mbps; 15 dBm @ 54 Mbps
2.412 to 2.472 GHz: 18 dBm @ 1 to 11 Mbps
5.15 to 5.25 GHz: 6 Mbps @ -90 dBm; 54 Mbps @ -72 dBm
5.725 to 5.825 GHz: 6 Mbps @ -89 dBm; 54 Mbps @ -72 dBm
2.412 to 2.483 GHz: 6 Mbps @ -90 dBm; 54 Mbps @ -73 dBm
2.412 to 2.472 GHz: 11 Mbps @ -87 dBm; 1 Mbps @ -94 dBm
Transmission Rate:
802.11a: 54 Mbps
802.11b: 11 Mbps
802.11g: 54 Mbps
Transmission Distance: Up to 100 meters (in open areas)
Wireless Security: AES, WEP 64/128-bit, WPA, WPA2, 802.11i
802.11i Authentication: TLS, PEAP/GTC, PEAP/MD5, PEAP/
MSCHAPv2, TTLS/PAP, TTLS/CHAP, TTLS/MSCHAP, TTLS/
MSCHAPv2, TTLS/EAP-MSCHAPv2, TTLS/EAP-GTC, TTLS/EAP-MD5,
LEAP
Channels:
North America: CH1 to CH11, 5150-5825 MHz
Europe: CH1 to CH13, 5150-5875 MHz
Japan: CH1 to CH14, 5150-5350 MHz
Antenna Connector: Reverse SMA
Antenna Gain: 2 DBi
info@moxa.com
Industrial Networking Solutions
Serial Interface
Environmental Limits
Number of Ports: 1
Serial Standards for Port 1: TTL
Serial Standards for Port 2: TTL console port
Operating Temperature: 0 to 55°C (32 to 131°F)
Operating Humidity: 5 to 95% RH
Storage Temperature: -20 to 70°C (-4 to 158°F)
Surface Temperature (at full baudrate of 921.6 Kbps)
Top Panel:
43.0°C, when air temp = 25°C
55.0°C, when air temp = 55°C
Bottom Panel:
44.5°C, when air temp = 25°C
67.0°C, when air temp = 55°C
Serial Communication Parameters
Data Bits: 5, 6, 7, 8
Stop Bits: 1, 1.5, 2
Parity: None, Even, Odd, Space, Mark
Flow Control: RTS/CTS, XON/XOFF, DTR/DSR
Baudrate: 50 bps to 921.6 Kbps (supports Any Baudrate in this
range)
Power Requirements
Serial Signals
TTL (Port 1): TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
TTL (Port 2): TxD, RxD, GND
Software
8
Regulatory Approvals
EMC: CE EN55022 Class A, FCC Part 15 Subpart B Class A
Safety: EN60950, CUL TÜV
Wireless:
CE ETSI EN 301 489-17
CE ETSI EN 301 489-1
FCC Part 15, Subpart B, Class A
FCC Part 17, Subpart B, Class A
Warranty
Warranty Period: 5 years
Details: See www.moxa.com/warranty
Dimensions (unit: mm) and Pin Assignment
WE-2100T
V1.0
Moxa Technologies Co., Ltd.
BqfNL010000
00:90:E8:OA:B1:CB
Made in Taiwan
3.3V
3.3V
3.3V
Console_TxD
Console_RTS
Console_DTR
PIO0
PIO1
PIO2
PIO3
Data_TxD
Data_RTS
Data_DTR
Ready_LED
Fault_LED
Eth_Tx+
Eth_TxEth_Center_TAP
Eth_Center_TAP
Eth_Rx+
Eth_RxPIO8(WLAN strength 0)
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
GND
GND
GND
Console_RxD
Console_CTS
Console_DSR
Console_DCD
PIO4(WLAN strength 1)
PIO5(WLAN strength 2)
PIO6(WLAN strength 3)
PIO7(WLAN strength 4)
Data_RxD
Data_CTS
Data_DSR
Data_DCD
WLAN_Active_LED
SW_RESET
HW_RESET
Eth_100M_LED
Eth_10M_LED
Reserved
Reserved
Serial Device Servers > WE-2100T Series
Internet Protocols: ICMP, IP, TCP, UDP, DHCP, Telnet, DNS, SNMP,
HTTP, SMTP, SNTP, SSH, HTTPS
Configuration Options: Web Console, Serial Console, Telnet Console,
Windows Utility (for Windows 98, ME, 2000, XP, 2003, Vista), Serial
command mode (configured through the data port)
Driver Support: Windows COM driver (for Windows 98, ME, NT,
2000, XP, 2003, XP x64, 2003 x64, Vista), Linux Real TTY driver,
SCO Unix, SCO OpenServer 5, UnixWare 7, UnixWare 2.1.x, SVR4.2,
QNX
Supported Operating Modes: Real COM, TCP Server, TCP Client,
UDP, RFC2217
Input Voltage: 3.3 VDC (±5%)
Power Consumption:
921.6 Kbps (full speed): 540 mA
Idle: 190 mA
Ethernet mode: 670 mA
Inrush current: 2100 mA
Ordering Information
Available Models
Package Checklist (module)
Package Checklist (starter kits)
WE-2100T: 1-port wireless module supporting
IEEE 802.11a/b/g
WE-2100T-ST: Starter Kit for the WE-2100T
UÊ WE-2100T wireless module
UÊ IEEE 802.11a/b/g Antenna
UÊ
UÊ
UÊ
UÊ
UÊ
UÊ
info@moxa.com
WE-2100T-ST evaluation board
WE-2100T wireless module
Power adaptor
Document and Software CD
Quick Installation Guide (printed)
Warranty Card
w w w. m o x a . c o m
8-43
Download PDF
Similar pages