Back Bar Bottle Coolers Instruction Manual

Back Bar Bottle Coolers
Models BD-CN-0007-HC, BB-CN-0012-DH, BD-CN-0019-HC,
BB-CN-0016-DH, BD-CN-0023-HC, BB-CN-0020-DH, BD-CN-0032-HC
Items 50066, 50063, 50067, 50064, 50068, 50065, 50069
Instruction Manual
Revised - 09/28/2017
Toll Free: 1-800-465-0234
Fax: 905-607-0234
Email: service@omcan.com
www.omcan.com
Table of Contents
Model BD-CN-0007-HC / Model BB-CN-0012-DH / Model BD-CN-0019-HC
Model BB-CN-0016-DH / Model BD-CN-0023-HC / Model BB-CN-0020-DH
Model BD-CN-0032-HC
Section
Page
General Information --------------------------------------------------------------------------- 3 - 4
Safety and Warranty --------------------------------------------------------------------------- 4 - 6
Technical Specifications -------------------------------------------------------------------------- 7
Installation -------------------------------------------------------------------------------------- 8 - 10
Operation ------------------------------------------------------------------------------------- 10 - 13
Cleaning and Maintenance --------------------------------------------------------------- 13 - 16
Parts Breakdown ---------------------------------------------------------------------------- 17 - 30
Electrical Schematics ---------------------------------------------------------------------- 31 - 37
Notes ------------------------------------------------------------------------------------------------- 38
Warranty Registration ---------------------------------------------------------------------------- 39
2
General Information
Omcan Manufacturing and Distributing Company Inc., Food Machinery of America, Inc. dba Omcan
and Omcan Inc. are not responsible for any harm or injury caused due to any person’s improper or
negligent use of this equipment. The product shall only be operated by someone over the age of 18, of
sound mind, and not under the influence of any drugs or alcohol, who has been trained in the correct
operation of this machine, and is wearing authorized, proper safety clothing. Any modification to the
machine voids any warranty, and may cause harm to individuals using the machine or in the vicinity of
the machine while in operation.
CHECK PACKAGE UPON ARRIVAL
Upon receipt of an Omcan shipment please inspect for external damage. If no damage is evident on the
external packaging, open carton to ensure all ordered items are within the box, and there is no concealed
damage to the machine. If the package has suffered rough handling, bumps or damage (visible or concealed),
please note it on the bill of lading before accepting the delivery and contact Omcan within 24 hours, so we may
initiate a claim with the carrier. A detailed report on the extent of the damage caused to the machine must be
filled out within three days, from the delivery date shown in the shipping documents. Omcan has no recourse
for damaged products that were shipped collect or third party.
Before operating any equipment, always read and familiarize yourself with all operation and safety
instructions.
Omcan would like to thank you for purchasing this machine. It’s of the utmost importance to save
these instructions for future reference. Also save the original box and packaging for shipping the
equipment if servicing or returning of the machine is required.
--------------------------------------------------------------------------------------------------------------------------------------------------Omcan Fabrication et distribution Companie Limité et Food Machinery d’Amerique, dba Omcan et
Omcan Inc. ne sont pas responsables de tout dommage ou blessure causé du fait que toute personne
ait utilisé cet équipement de façon irrégulière. Le produit ne doit être exploité que par quelqu’un de
plus de 18 ans, saine d’esprit, et pas sous l’influence d’une drogue ou d’acohol, qui a été formé pour
utiliser cette machine correctement, et est vêtu de vêtements de sécurité approprié. Toute modification
de la machine annule toute garantie, et peut causer un préjudice à des personnes utilisant la machine
ou des personnes à proximité de la machine pendant son fonctionnement.
VÉRIFIEZ LE COLIS DÈS RÉCEPTION
Dès réception d’une expédition d’Omcan veuillez inspecter pour dommages externes. Si aucun dommage
n’est visible sur l’emballage externe, ouvrez le carton afin de s’assurer que tous les éléments commandés
sont dans la boîte, et il n’y a aucun dommage dissimulé à la machine. Si le colis n’a subi aucune mauvaises
manipulations, de bosses ou de dommages (visible ou cachée), notez-le sur le bond de livraison avant
d’accepter la livraison et contactez Omcan dans les 24 heures qui suivent, pour que nous puissions engager
une réclamation auprès du transporteur. Un rapport détaillé sur l’étendue des dommages causés à la machine
doit être rempli dans un délai de trois jours, à compter de la date de livraison indiquée dans les documents
d’expédition. Omcan n’a aucun droit de recours pour les produits endommagés qui ont été expédiées ou cueilli
par un tiers transporteur.
3
General Information
Avant d’utiliser n’importe quel équipement, toujours lire et vous familiariser avec toutes les opérations
et les consignes de sécurité.
Omcan voudrais vous remercier d’avoir choisi cette machine. Il est primordial de conserver ces
instructions pour une référence ultérieure. Également conservez la boîte originale et l’emballage pour
l’expédition de l’équipement si l’entretien ou le retour de la machine est nécessaire.
--------------------------------------------------------------------------------------------------------------------------------------------------Omcan Empresa De Fabricacion Y Distribucion Inc. Y Maquinaria De Alimentos De America, Inc. dba
Omcan y Omcan Inc. no son responsables de ningun daño o perjuicío causado por cualquier persona
inadecuada o el uso descuidado de este equipo. El producto solo podra ser operado por una persona
mayor de 18 años, en su sano juicio y no bajo alguna influencia de droga o alcohol, y que este ha sido
entrenado en el correcto funcionamiento de esta máquina, y ésta usando ropa apropiada y autorizada.
Cualquier modificación a la máquina anúla la garantía y puede causar daños a las personas usando la
máquina mientras esta en el funcionamiento.
REVISE EL PAQUETE A SU LLEGADA
Tras la recepcion de un envio Omcan favor inspeccionar daños externos. Si no hay daños evidentes en el
empaque exterior, Habra el carton para asegurararse que todos los articulos solicitados ésten dentro de la
caja y no encuentre daños ocultos en la máquina. Si el paquete ha sufrido un manejo de poco cuidado, golpes
o daños (visible o oculto) por favor anote en la factura antes de aceptar la entrega y contacte Omcan dentro
de las 24 horas, de modo que podamos iniciar una reclamación con la compañia. Un informe detallado sobre
los daños causados a la máquina debe ser llenado en el plazo de tres días, desde la fecha de entrega que se
muestra en los documentos de envío. Omcan no tiene ningun recurso por productos dañados que se enviaron
a recoger por terceros.
Antes de utilizar cualquier equipo, siempre lea y familiarizarse con todas las instrucciones de
funcionamiento y seguridad.
Omcan le gustaría darle las gracias por la compra de esta máquina. Es de la mayor importancia para
salvar estas instrucciones para futuras consultas. Además, guarda la caja original y el embalaje para el
envío del equipo si servicio técnico o devolución de la máquina que se requiere.
Safety and Warranty
When using electrical appliances basic safety precautions should be followed:
• This cooler must be properly installed and located in accordance with the installation service
representative.
• Do not allow children to climb, stand or hang on the shelves in the cooler. They could damage the unit and
seriously injure themselves.
• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance.
4
Safety and Warranty
•
•
Unplug the unit from the electrical outlet before cleaning or making repairs.
Setting the temperature controls to the 0 (zero) position does not remove power to the light circuit,
perimeter heaters or evaporator fans.
NOTE: It is strongly recommended that any servicing be performed by an authorized instructions before it is
used.
ELECTRICAL SAFETY
Do not under any circumstances cut or remove the grounding prong from the power cord. For safety this
appliance must be properly grounded at all times.
•
•
•
•
•
•
•
•
•
•
•
•
•
The power cord of this cooler is equipped with a grounding plug which mates with a standard grounding
wall outlet to minimize the possibility of electric shock hazard.
If the outlet is a standard 2-prong outlet, it must be replaced with the properly grounded wall outlet. NEVER
USE AN ADAPTER PLUG!
Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly
grounded. Check the incoming voltage with a voltmeter.
DO NOT USE EXTENSION CORDS. The use of extension cords to connect the cooler will void warranty.
The unit must be close enough to the electrical supply so that extension cords are never used.
The cooler should always be plugged into its own dedicated circuit with a voltage rating that matches the
rating plate. This provides the best performance and also prevents overloading wiring circuits which could
become a fire hazard from overheated wires.
Never unplug your cooler by pulling on the power cord. Always grip the plug firmly and pull straight out from
the outlet.
Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use
a power cord that has cracks or abrasion damage along its length or at either of its ends.
When removing the cooler away from the wall be careful not to run over or damage the power cord.
When the cooler is installed or used, all the packaging (including carton and plastic wrap) should be
removed.
Keep the cooler stable to avoid vibration and noise.
The cooler should be installed in a place with good ventilation and a space of at least 6” should be allowed
between the surrounding walls and the cabinet wall for air circulation.
Unit should be placed far from any heating source to avoid decrease of refrigeration efficiency.
Install the cooler in a dry place to prevent rust from forming on the compartment body, which may affect the
electrical insulation.
It is strongly recommended that any servicing be performed by an authorized service representative.
NOTE: Wiring diagram can be referenced by removing the front louvered grill, and looking on the inside
cabinet wall electrical supply so that extension cords are never used.
CAUTION
•
•
The cooler must be grounded correctly, never with a heating pipe and coal gas pipe.
In case of damage to electrical cord and plug, please contact after sale service and never do it yourself.
5
Safety and Warranty
•
•
•
•
When unplugging unit, please grasp by the plug, not the cord.
If the voltage is unstable, please select a suitable automatic voltage regulator.
If the power cuts off, you should wait for at least 5 minutes before turning on the unit again to avoid
damage to the compressor.
Never store any flammable, explosive or corrosive liquid or gas in or near the cooler.
PROPER DISPOSAL OF EQUIPMENT; DANGER! RISK OF CHILD ENTRAPMENT
Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still
dangerous, even if they will sit for “just a few days.” If you are getting rid of an old refrigerator, please follow the
below instructions to help prevent a terrible accident.
• Remove the doors.
• Leave shelves in place to prevent children from easily climbing inside.
REFRIGERANT DISPOSAL
Your old refrigerator may have a cooling system that used “ozone depleting” chemicals. If you are throwing
away your old refrigerator, be sure the refrigerant is removed for proper disposal by a qualified service
technician. If you intentionally release any refrigerants you can be subject to fines and imprisonment under the
provisions of the environmental regulations.
1 YEAR PARTS AND LABOUR WARRANTY
Within the warranty period, contact Omcan Inc. at 1-800-465-0234 to schedule an Omcan authorized
service technician to repair the equipment locally.
Unauthorized maintenance will void the warranty. Warranty covers electrical and part failures, not
improper use.
Please see www.omcan.com/warranty.html for complete info.
WARNING:
The packaging components are classified as normal solid urban waste and can therefore be disposed of
without difficulty.
In any case, for suitable recycling, we suggest disposing of the products separately (differentiated
waste) according to the current norms.
DO NOT DISCARD ANY PACKAGING MATERIALS IN THE ENVIRONMENT!
6
Technical Specifications
Model
Number of Doors
BD-CN-0007-HC
BB-CN-0012-DH
BD-CN-0019-HC
1
2
Temperature Range
33 - 41°F / 0.5 - 5°C
Refrigerant
Capacity
Number of Shelves
Compressor HP
BB-CN-0016-DH
R290
6.5 cu.ft. / 186 L
11.8 cu.ft. / 335 L
19 cu.ft. / 546 L
2
4
1/6
1/5
Voltage
15.8 cu.ft. / 446 L
115V / 60Hz
Power
0.18 kW
0.44 kW
0.42 kW
0.46 kW
Amps
1.92A
3A
2.88A
3A
Dimensions (DWH)
30.4” x 23.5” x 38.8”
772 x 596 x 983mm
24.4” x 48.8” x 35.5”
620 x 1240 x 905mm
27.8” x 58.9” x 35.5”
705 x 1495 x 905mm
24.4” x 60.8” x 35.5”
620 x 1544 x 905mm
Interior Dimensions
(DWH)
18.3” x 19.5” x 30.3”
464 x 495 x 768mm
20” x 36.2” x 31”
508 x 919 x 787mm
23.4” x 46.5” x 31”
594 x 1181 x 787mm
20” x 48.2” x 31”
508 x 1224 x 787mm
Packaging
Dimensions (DWH)
32.5” x 25.8” x 44.9” 27.6” x 51.2” x 42.3”
30.5” x 61.4” x 41.8”
27.6” x 63.4” x 42.3”
826 x 654 x 1140mm 701 x 1300 x 1074mm 775 x 1559 x 1060mm 701 x 1610 x 1074mm
Weight
150 lbs. / 68 kgs.
271 lbs. / 123 kgs.
293 lbs. / 133 kgs.
326 lbs. / 148 kgs.
Packaging Weight
187 lbs. / 85 kgs.
315 lbs. / 143 kgs.
337 lbs. / 153 kgs.
380 lbs. / 173 kgs.
50066
50063
50067
50064
Item Number
Model
Number of Doors
BD-CN-0023-HC
BB-CN-0020-DH
2
Temperature Range
33 - 41°F / 0.5 - 5°C
Refrigerant
Capacity
Number of Shelves
Compressor HP
BD-CN-0032-HC
3
R290
23.3 cu.ft. / 666 L
19.6 cu.ft. / 556 L
32 cu.ft. / 916 L
4
6
1/5
1/4+
Voltage
115V / 60Hz
Power
0.54 kW
0.5 kW
0.64 kW
Amps
3.6A
4A
4.7A
Dimensions (DWH)
27.8” x 69.1” x 35.5”
705 x 1755 x 905mm
24.4” x 72.8” x 35.5”
620 x 1848 x 905mm
27.8” x 90.4” x 35.5”
705 x 2295 x 905mm
Interior Dimensions
(DWH)
23.4” x 56.5” x 31”
594 x 1435 x 787mm
20” x 60.2” x 31”
508 x 1529 x 787mm
23.4” x 77.8” x 31”
594 x 1975 x 787mm
Packaging
Dimensions (DWH)
31” x 72” x 42”
787 x 1829 x 1067mm
27.6” x 75.2” x 42.3”
701 x 1910 x 1074mm
30.5” x 91.8” x 41.8”
775 x 2330 x 1060mm
348 lbs. / 158 kgs.
355 lbs. / 161 kgs.
375 lbs. / 170 kgs.
331 lbs. / 150.1 kgs.
410 lbs. / 186 kgs.
419 lbs. / 190 kgs.
50068
50065
50069
Weight
Packaging Weight
Item Number
7
Installation
Tools required: Phillips screw driver.
•
•
•
Use a Phillips screw driver to remove the four (4) screws from the L-bracket connecting the unit to the
wood skid. Then remove the L-bracket from the unit.
Remove skid by unscrewing all base rail anchor brackets. Place skid to the side.
Carefully upright cabinet.
When lifting unit do not use the counter top as a lifting point. Also remember to leave cabinet upright
for 24-hours before plugging into power source.
•
Set unit in its final location. Make sure there is adequate ventilation in this location. Under extreme heat
conditions (+100°F / +38°C) an exhaust fan may be necessary.
• Proper leveling of the unit is critical to operating success (for non-mobile models). Effective condensate
removal and door operation will be affected by leveling.
• The cooler should be leveled front to back and side to side with a level.
Warning: Installation without proper ventilation will void the manufacturer’s warranty.
SEALING CABINET TO FLOOR
Step 1 - Position Cabinet
Allow six (6) inches between the wall and rear of the refrigerated bar equipment to assure proper ventilation.
Step 2 - Level Cabinet
Cabinet should be level side to side and front to back. Place a carpenter’s level in the interior cabinet floor in
four places:
A Position level in the inside floor of the unit near the door. Level should be parallel to cabinet front.
B Position level at the inside rear of cabinet. Level should be placed parallel to cabinet back.
C Perform similar procedures to steps A and B by placing the level on inside floor left and right sides parallel to
the depth of the cooler. Level cabinet.
Step 3 - Applying Sealant
• Draw an outline on the base of the floor.
• Raise and block the front side of the cabinet.
• Apply a bead of NSF Approved Sealant (see list below) to floor half an inch inside the outline drawn. The
bead must be heavy enough to seal the entire cabinet surface when it set down on the sealant.
• Raise and block the rear of the cabinet.
• Apply sealant on floor as outlined above on other 3 sides.
• Examine to see that the cabinet is sealed to floor around entire perimeter.
NSF APPROVED SEALANTS:
• Minnesota Mining #ECU800 Caulk.
• Minnesota Mining #ECU2185 Caulk.
8
Installation
•
•
•
•
•
•
BEER DISPENSING SYSTEM
Minnesota Mining #ECU1055 Bead.
Minnesota Mining #ECU1202 Bead.
Armstrong Cork - Rubber Caulk.
Products Research Co #5000 Rubber Caulk.
GE Silicone Sealer.
Dow Corning Silicone Sealer.
NOTE: Asphalt floors are very susceptible to chemical
attack. A layer of tape on the floor prior to applying the
sealant will protect the floor.
DRAFT BEER TOWER INSTALLATION
1. Beer tower contents.
2. Thread the beer line connector to the keg coupler.
3. Insert an air hose into the beer tower and secure the
beer tower to cabinet with the gasket under the beer
tower.
4. Make sure the air hose closes at the top of beer tower at all times. This is to keep the beer faucet cold.
5. Secure the handle onto beer faucet.
9
Installation
REMOTE CO2 GAS CYLINDER INSTALLATION
1. Remove the plug on the right wall of the machine with a pair of pliers.
2. Drill and make hole through the wall. Holes can be located in two
different areas. Reference above pictures for the position of the holes.
3. Insert the CO2 line through the hole.
4. Seal the hole around CO2 line with silicone sealer to prevent leakage
of cold air.
Operation
START UP
Plug in the cooler and the compressor is ready to operate.
•
•
•
Temperature control set at #4 position gives the cooler an approximate temperature of 35°F. Allow unit to
function several hours, completely cooling cabinet before changing the control setting.
Excessive tampering with the control could lead to service difficulties. Should it ever become necessary to
replace the temperature control it should be ordered from your dealer or recommended service agent.
Good air flow in your cooler is critical. Be careful to load product so that it neither presses against the back
wall nor comes within four (4) inches of the evaporator housing. Refrigerated air off the coil must circulate
down the back wall.
LIGHT SWITCH LOCATION:
The switch is located on the front of the evaporator housing toward the right of the cabinet. Open the front
door.
NOTE: If the unit is disconnected or shut off, wait five (5) minutes before re-starting unit.
RECOMMENDATION
Before loading product the unit should be run for 2 to 3 days. This allows confirmation that the electrical wiring
and installation are correct and no shipping damage has occurred. Remember that the factory warranty does
10
Operation
not cover product loss.
REPLACEMENT PARTS
We maintains a record of the cabinet model number and serial number for your cooler. If at any time during
the life of your cooler a replacement part is needed, call the factory office with the model number and serial
number of your unit to place an order for the part.
CONTROLLER INSTRUCTIONS
DIGITAL CONTROLLER MODEL: PJEZ FOR COOLER
DISPLAY AND FUNCTIONS
During normal operation, the controller displays the value of the probe set using parameter/4(=1 ambient
probe, default, = 2 second probe, = 3 third probe).In addition, the display has LEDs that indicate the activation
of the control functions (see Table 1), while the 3 buttons can be used to activate/deactivate some of the
functions(see Table 2).
LED’s and Associated Functions (Table 1)
Icon
Function
Normal Operation
ON
OFF
Compressor On
Off
Fan
On
Off
Defrost
On
Off
Aux
Output On
Output Off
Alarm
All
No Alarm
Clock
RTC fitted and enabled, at RTC not fitted or disabled, not
least 1 time band set
even 1 time band set
11
Start Up
Blink
Request
Request
Request
-
ON
ON
ON
ON
ON
ON if RTC
fitted
Operation
Table of Functions activated by the buttons - Models S, X, Y, C (Table 2)
Button
Up
ON/OFF
Down
Defrost
Set Mute
Normal Operation
Start Up
Pressing the Button Alone Pressed Together
More than 3 sec: toggle ON/ Start/Stop
OFF
continuous cycle
More than 3 sec: start/stop
Pressed
For 1 sec.
defrost
together
display
Start parameter firmware
reset procedure vers. code
- 1 sec.: display/set the set For 1 sec.
point.
RESET cur- more than 3 secs.: access
rent EZY set
parameter setting menu
(enter password )
- mute audible alarm
(buzzer)
SETTING THE SET POINT (DESIRED TEMPERATURE)
• Press SET for 1 sec, the set value will start flashing after a few moments.
• Increase or decrease the value using UP or DOWN.
• Press SET to confirm the new value.
SWITCHING THE DEVICE ON/OFF
Press UP for more than 3 sec. The control and defrost algorithms are now disabled and the Instrument
displays the message “OFF” alternating with the temperature read by the set probe.
MANUAL DEFROST
Press for DOWN more than 3 sec (the defrost starts only the temperature conditions are valid).
CONTINUOUS CYCLE
Press UP and DOWN together for more than 3 sec.
ACCESS AND SETTING TYPE F (FREQUENT) AND TYPE C (CONFIGURATION)
PARAMETERS
1. Press SET for 3 sec (the display will show “PS”).
2. • To access the type F and C parameter menu, enter the password “22” using UP/DOWN, press SET to
confirm.
• To access the F parameter menu only, press SET (without entering the password).
12
Operation
3. Scroll inside the parameter menu using UP/DOWN.
• To display/set the values of the parameter displayed, press SET, then UP/DOWN and finally SET to
confirm the changes (returning to the parameter menu).
To save all the new values and exit the parameter menu, press SET for 3 sec.
To exit the menu without saving the changed values (exit by timeout) do not press any button for at least 60
sec.
MECHANICAL CONTROLLER INSTRUCTIONS
OFF: shut the compressor off.
Temperature range from 7 (coldest) to 1 (warmest).
CAUTION: Setting the temperature control to the coldest setting may cause the
evaporator coil to freeze and ice up. This will eventually result in a warmer cabinet
temperature.
Cleaning and Maintenance
Condensers accumulate dirt and dust and require cleaning every 30 days. Dirty condensers result in
compressor failure, product loss, and lost sales -- which are not covered by warranty.
Air is pulled through the condenser continuously along with dust, lint, grease, etc. If you keep the condenser
clean you will minimize your service expense and lower your electrical costs. The condenser requires
scheduled cleaning every days or as needed. A dirty condenser can result in non-warranted part and
compressor failures and product loss.
Proper cleaning involves removing debris from the condenser by using a soft brush or vacuuming the
condenser with a shop vac or using Co2, nitrogen or pressurized air.
If you cannot remove the debris adequately please call you refrigeration service company.
On most of the reach-in units the condenser is accessible at the rear of the unit. You must remove the cabinet
grill to expose the condenser. The condenser looks like a group of vertical fins. You need to be able to see
through the condenser for the unit to function at maximum capacity. Do not place filter material in front of
condensing coil. This material blocks air flow to the coil which is similar to having a dirty coil.
13
Cleaning and Maintenance
CLEANING THE CONDENSER COIL
Required Tools:
•
•
•
Phillips screwdriver.
Stiff bristle brush.
Adjustable wrench
When using electrical appliances basic safety precautions should be followed:
•
•
•
•
•
•
•
•
•
Disconnect power to unit.
Take off lower grill assembly by removing all screws.
Remove bolts anchoring compressor assembly to frame rails and carefully slide out -- tube connections are
flexible.
Clean off accumulated dirt from condensing coil with the stiff bristle brush.
Lift cardboard cover above fan at plastic plugs and carefully clean condenser coil and fan blades.
After brushing condenser coil, vacuum dirt from coil and interior floor.
Replace cardboard cover, carefully slide compressor assembly back into position and replace bolts.
Reinstall louver assembly onto unit with appropriate fasteners and clips. Tighten all screws.
Connect unit to power and check to see if condenser is running.
STAINLESS STEEL CARE AND CLEANING
Recommended cleaners for stainless steel
•
•
•
•
•
•
Soap, ammonia and detergent medallion applied with a soft cloth or sponge for routine cleaning.
Arcal 20, Loc-O-Nu Ecoshine provide a barrier film for fingerprints and smears.
Cameo, Talc, Zud First lmpression is for stubborn stains and discoloration. Rub in direction of polish lines.
Easy-off and De-Grease It oven aid are excellent for removals on all finishes for grease-fatty acids, blood
and burnt-on foods.
Any good commercial detergent can be applied with a sponge or soft cloth to remove grease and oil.
Benefit, Super Sheen, Sheila Shine are good for restoration/passiveness.
CAUTION: Do not use any steel wool, abrasive or chlorine based products to clean stainless steel surfaces.
Stainless Steel Enemies
There are three basic items that can break down stainless steel’s passivity layer and allow corrosion to occur.
1. Scratches from wire brushes, metal scrapers and steel pads are just a few examples of items that can be
abrasive to stainless steel’s surface.
2. Deposits left on stainless steel can leave spots. Hard water can leave spots. Hard water that is heated can
leave deposits if left to sit for too long. These deposits can cause the passive layer to break down and rust
stainless steel. All deposits left from food prep or service should be removed as quickly as possible.
3. Chlorides are present in table salt, food and water. Household and industrial cleaners are the worst type of
chlorides to use.
14
Cleaning and Maintenance
8 Steps that can help prevent rust on stainless steel
1. Use the correct cleaning tools. Use non-abrasive tools when cleaning your stainless steel products. The
stainless steel’s passive layer will not be harmed by soft cloths and plastic scouring pads.
2. Clean along the polish lines. Polish lines or grain are visible on some stainless steel. Always scrub parallel
to visible lines. Use a plastic scouring pad or soft cloth when grain is not visible.
3. Use alkaline, alkaline chlorinated or non-chloride containing cleaners. While many traditional cleaners are
loaded with chlorides, the industry is providing an ever increasing choice of non-chloride cleaners. If unsure
of chloride content contact the cleaner supplier. If present cleaner contains chlorides, ask for an alternative.
Avoid cleaners containing quaternary salts as they can attack stainless steel causing pitting and rusting.
4. Water treatment. To reduce deposits, use soft water whenever possible. Installation of certain filters can be
an advantage. Contact a treatment specialist about proper water treatment.
5. Maintain cleanliness of food equipment. Use cleaners at recommended strength(alkaline, alkaline
chlorinated or non-chloride). Avoid buildup of hard stains by cleaning frequently.
6. When using chlorinated cleaners you must rinse and wipe dry immediately. It is better to wipe standing
cleaning agents and water as soon as possible. All stainless steel equipment to air dry. Oxygen helps
maintain the passivity film on stainless steel.
7. Hydrochloric acid (muriatic acid) should never be used on stainless steel.
8. Regularly restore/clean stainless steel.
KEG BEER LINE CLEANING
1. Tools needed.
2. Pour cleaning solution and water into the pump bottle and connect it to the beer line.
3. Place a bucket under the faucet and open the beer faucet. Pump to remove the cleaning solution and
water. Continue to pump until all cleaning solution has exited. You can also fill the line and let it soak then
run through the line. After you have run the cleaning solution through, open the bottle and fill with water.
Repeat water rinsing until the line is free of cleaning chemicals.
15
Cleaning and Maintenance
REFERENCE
Item Number
Model Number
50066
BD-CN-0007-HC
50063
BB-CN-0012-DH
50067
BD-CN-0019-HC
50064
BB-CN-0016-DH
50068
BD-CN-0023-HC
50065
BB-CN-0020-DH
50069
BD-CN-0032-HC
Description
Beer Dispenser Single Solid Door with
One Tap 6.5 cu ft / 186 L Capacity
110V/60HZ ETL cETLus INTERTEK
Cooler Back Bar 11.8 cu ft Capacity Solid
Door with Beer Dispenser 115V/60/1 NSF
ETL cETLus INTERTEK
Beer Dispenser Double Solid Doors
with One Tap 19 cu ft / 546 L Capacity
110V/60HZ ETL cETLus INTERTEK
Cooler Back Bar 15.8 cu ft Capacity Solid
Door with Beer Dispenser 115V/60/1 NSF
ETL cETLus INTERTEK
Beer Dispenser Double Solid Doors with
Two Taps 23.3 cu ft / 666 L Capacity
110V/60HZ ETL cETLus INTERTEK
Cooler Back Bar 19.6 cu ft Capacity Solid
Door with Beer Dispenser 115V/60/1 NSF
ETL cETLus INTERTEK
Beer Dispenser Three Solid Doors with
Two Taps 32 cu ft / 916 L Capacity
110V/60HZ ETL cETLus INTERTEK
16
Manufacturer Model
Number
UDD-1-HC
UDD-24-48-HC
UDD-2-HC
UDD-24-60-HC
UDD-3-HC
UDD-24-72-HC
UDD-4-HC
Parts Breakdown
Model BD-CN-0007-HC 50066
17
Parts Breakdown
Model BD-CN-0007-HC 50066
Item No.
Description
Position
Item No.
Description
Position
Item No.
Description
Position
35
71725
Cabinet for UDD-1-HC
1
71733
Back Cover for UDD-1-HC
18
71745
Reinforcing Plate of Interior Floor for
UDD-1-HC
71726
Top Board for UDD-1-HC
2
26246
Front Castor for UDD-1-HC
19
71746
Rear Castor for UDD-1-HC
36
71727
Counter Top Tray for UDD-1-HC
3
71734
Solid Door for UDD-1-HC
20
71747
Counter Top Railing for UDD-1-HC
37
71843
Beer Tower for UDD-1-HC
4
26164
Spring Hinge of Solid Door for UDD-1-HC
21
71748
Exterior Water Tray for UDD-1-HC
38
71844
Cover of Top Tray for UDD-1-HC
5
26760
Axis Sleeve for UDD-1-HC
22
71749
Plastic Bottle for UDD-1-HC
39
71728
Plastic Mounting Plate of Beer Tower for
UDD-1-HC
6
37731
Upper Right Hinge for UDD-1-HC
23
71750
Plastic Pipe of CO2 Line for UDD-1-HC
40
71851
Drain Connector Nut of Top Tray for
UDD-1-HC
7
71735
Evaporator for UDD-1-HC
24
71751
Rubber Cover of Plastic Pipe of CO2
Line for UDD-1-HC
41
73071
Drain Connector of Top Tray for UDD1-HC
8
71736
Fan Motor Installation Panel for UDD1-HC
25
71752
Tape of Plastic Bottle for UDD-1-HC
42
71847
Drain Hose of Top Tray for UDD-1-HC
9
71737
Evaporator Fan Motor Bracket for
UDD-1-HC
26
71753
Door Seal for UDD-1-HC
43
37735
Fixed Block of Top Board for UDD-1-HC
10
71738
Evaporator Fan Motor for UDD-1-HC
27
26198
Door Lock for UDD-1-HC
44
37728
Bottom Right Hinge of Door for UDD1-HC
11
71795
Blade of Evaporator Fan Motor for
UDD-1-HC
28
71754
Air Tube of Beer Tower for UDD-1-HC
45
37734
Plate of Lock for UDD-1-HC
12
71739
Left Plate of Evaporator for UDD-1-HC
29
37694
Mechanical Temperature Controller for
UDD-1-HC
46
71729
Bottom Plate of Machine Room for
UDD-1-HC
13
71740
Right Plate of Evaporator for UDD-1-HC
30
37693
Panel of Temperature Controller for
UDD-1-HC
47
71730
Compressor Unit Installation Board for
UDD-1-HC
14
71741
Evaporator Cover for UDD-1-HC
31
37696
Knob of Temperature Controller for
UDD-1-HC
48
71731
Condenser for UDD-1-HC
15
71742
Cover of Copper Pipe for UDD-1-HC
32
73072
Defrost Timer for UDD-1-HC
49
71732
Compressor for UDD-1-HC
16
71743
Cover of Inner Drain Hose for UDD-1-HC
33
37705
Condenser Fan Motor for UDD-1-HC
17
71744
Bracket of Defrost Timer for UDD-1-HC
34
18
Parts Breakdown
Model BB-CN-0012-DH 50063
19
Parts Breakdown
Model BB-CN-0012-DH 50063
Item No.
Description
Position
Item No.
Description
Position
Item No.
Description
Position
71788
Cabinet for UDD-24-48-HC
1
71810
Outer Drain Pan for UDD-24-48-HC
23
71832
Adjusted Feet for UDD-24-48-HC
45
46
71789
Top Board for UDD-24-48-HC
2
71811
Filter Fixer for UDD-24-48-HC
24
71833
Stop Block of Compressor Unit
Installation Board for UDD-24-48-HC
71790
Inner Drain Pan for UDD-24-48-HC
3
71812
Filter for UDD-24-48-HC
25
71834
K Strip-2 Holes for UDD-24-48-HC
47
71791
Evaporator for UDD-24-48-HC
4
71813
Lateral Cover of Machine Room for
UDD-24-48-HC
26
71835
Handle of Compressor Unit Installation
Board for UDD-24-48-HC
48
71792
Fan Motor Installation Panel for UDD24-48-HC
5
71814
Front Cover of Machine Room for UDD24-48-HC
27
71836
Ballast of Light for UDD-24-48-HC
49
71793
Evaporator Fan Motor for UDD-24-48-HC
6
71815
Left Solid Door for UDD-24-48-HC
28
71837
Condenser Bracket for UDD-24-48-HC
50
71794
Evaporator Fan Motor Holder for UDD24-48-HC
7
71816
Solid Door Gasket for UDD-24-48-HC
29
71838
Temperature Display for UDD-24-48-HC
51
71795
Blade of Evaporator Fan Motor for
UDD-24-48-HC
8
71817
Right Solid Door for UDD-24-48-HC
30
71839
Transformer of Temperature Display for
UDD-24-48-HC
52
71796
Evaporator Cover for UDD-24-48-HC
9
71818
Axis Sleeve for UDD-24-48-HC
31
71840
Transformer Bracket of Temperature
Display for UDD-24-48-HC
53
71797
Temperature Control Panel for UDD24-48-HC
10
71819
Bottom Right Hinge for UDD-24-48-HC
32
71841
Sensor of Temperature Display for
UDD-24-48-HC
54
71798
Mechanical Thermostat for UDD-2448-HC
11
71820
Bottom Left Hinge for UDD-24-48-HC
33
71842
Spring Hinge for UDD-24-48-HC
55
71799
Temperature Control Knob for UDD24-48-HC
12
71821
Upper Right Hinge for UDD-24-48-HC
34
71843
Beer Tower for UDD-24-48-HC
56
71800
Light Switch for UDD-24-48-HC
13
71822
Upper Left Hinge for UDD-24-48-HC
35
71844
Cover of Top Tray for UDD-24-48-HC
57
71801
Bracket of Lateral Cover for UDD-2448-HC
14
71823
Plate of Lock for Right Door for UDD24-48-HC
36
71845
Cover of CO2 Line for UDD-24-48-HC
58
71802
Compressor Unit Installation Board for
UDD-24-48-HC
15
71824
Bottom Gasket of Compressor for UDD24-48-HC
37
71846
Cover of L Shape Connector for UDD24-48-HC
59
71803
Condenser for UDD-24-48-HC
16
71825
Fixed Block for Worktop for UDD-2448-HC
38
71847
Drain Hose of Top Tray for UDD-2448-HC
60
71804
Compressor for UDD-24-48-HC
17
71826
K Strip-4 Holes for UDD-24-48-HC
39
71848
L Shape Connector for UDD-24-48-HC
61
71805
Wiring Box of Compressor for UDD24-48-HC
18
71827
K Clip for UDD-24-48-HC
40
71849
Rubber Pad for UDD-24-48-HC
62
71806
Start Capacitor for UDD-24-48-HC
19
71828
Shelf for UDD-24-48-HC
41
71850
Drain Connector of Top Tray for UDD24-48-HC
63
71807
Overload Protector for UDD-24-48-HC
20
71829
LED Light for UDD-24-48-HC
42
71851
Drain Connector Nut of Top Tray for
UDD-24-48-HC
64
71808
Starter for UDD-24-48-HC
21
71830
Drain Hose for UDD-24-48-HC
43
71852
Air Tube for UDD-24-48-HC
65
71809
Condenser Fan Motor for UDD-24-48-HC
22
71831
Power Cord for UDD-24-48-HC
44
20
Parts Breakdown
Model BD-CN-0019-HC 50067
21
Parts Breakdown
Model BD-CN-0019-HC 50067
Item No.
Description
Position
Item No.
Description
Position
Item No.
Description
Position
46
71755
Cabinet for UDD-2-HC
1
26188
Filter Base D25 for UDD-2-HC
24
28311
Installation Board Limited Block for
UDD-2-HC
71756
Top Board for UDD-2-HC
2
26189
Filter D25x140 for UDD-2-HC
25
71834
K Strip 2 Holes for UDD-2-HC
47
48
37685
Inner Drain Pan for UDD-2-HC
3
71761
Lateral Cover for UDD-2-HC
26
71835
Handle of Compressor Unit Installation
Board for UDD-2-HC
71757
Evaporator for UDD-2-HC
4
37708
Front Cover of Machine Room for
UDD-2-HC
27
71836
Ballast for UDD-2-HC
49
71758
Fan Motor Installation Panel for UDD2-HC
5
71762
Left Door (Solid) for UDD-2-HC
28
71837
Condenser Installation Board for
UDD-2-HC
50
37688
Evaporator Fan Motor for UDD-2-HC
6
71763
Door Gasket (Solid) for UDD-2-HC
29
71838
Temp Display for UDD-2-HC
51
37689
Evaporator Fan Motor Holder for
UDD-2-HC
7
71764
Right Door (Solid) for UDD-2-HC
30
71839
Transformer for Temp Display for
UDD-2-HC
52
37690
Evaporator Fan Motor Blade for UDD2-HC
8
26760
Axis Sleeve for UDD-2-HC
31
71840
Temp Display Transformer Holder for
UDD-2-HC
53
71759
Evaporator Cover for UDD-2-HC
9
37728
Lower Right Hinge for UDD-2-HC
32
71841
Temp Sensor for Temp Display for
UDD-2-HC
54
37693
Temperature Control Panel for UDD2-HC
10
37730
Lower Left Hinge for UDD-2-HC
33
26164
Spring Hinge for UDD-2-HC
55
37694
Temperature Controller for UDD-2-HC
11
37731
Upper Right Hinge for UDD-2-HC
34
71843
Beer Tower for UDD-2-HC
56
37697
Lamp Switch for UDD-2-HC
13
37732
Upper Left Hinge for UDD-2-HC
35
71844
Cover of Top Tray for UDD-2-HC
57
71760
Bracket of Lateral Cover for UDD-2-HC
14
37734
Plate of Lock for UDD-2-HC
36
71845
CO2 Pipe Hole Cover for UDD-2-HC
58
37699
Compressor Unit Installation Board for
UDD-2-HC
15
73073
Rubber Base of Compressor for UDD2-HC
37
73074
Bottom Drain Plug Cover for UDD-2-HC
59
37700
Condenser 4R11K150L for UDD-2-HC
16
37735
Fixed Block of Top Board for UDD-2-HC
38
71847
Drain Hose of Top Tray for UDD-2-HC
60
26183
Compressor NE6187Z for UDD-2-HC
17
37736
K Strip 4 Holes for UDD-2-HC
39
71848
L Shape Connector for UDD-2-HC
61
37701
Splice Box for UDD-2-HC
18
26884
K Clip for UDD-2-HC
40
71766
Rubber Pad for UDD-2-HC
62
37702
Start Capacitor for UDD-2-HC
19
71774
Shelf (Left & Right) for UDD-2-HC
41
73075
Beer Tray Drain Plug for UDD-2-HC
63
37703
Overload Protector for UDD-2-HC
20
37741
LED Bulb for UDD-2-HC
42
73076
Beer Tray Drain Plug Nut for UDD-2-HC
64
37704
Starter for UDD-2-HC
21
26203
Drain Hose φ16 for UDD-2-HC
43
71767
Air Pipe for UDD-2-HC
65
37705
Condenser Fan Motor RAM4715 for
UDD-2-HC
22
26205
Power Cord 16 AWG for UDD-2-HC
44
71768
Middle Beam Cover for UDD-2-HC
66
37706
Outer Drain Pan for UDD-2-HC
23
28236
Adjustable Feet M12x45 for UDD-2-HC
45
22
Parts Breakdown
Model BB-CN-0016-DH 50064
23
Parts Breakdown
Model BB-CN-0016-DH 50064
Item No.
Description
Position
Item No.
Description
Position
Item No.
Description
Position
71853
Cabinet for UDD-24-60-HC
1
71876
Filter Fixer for UDD-24-60-HC
24
71899
K Strip-2 Holes for UDD-24-60-HC
47
48
71854
Top Board for UDD-24-60-HC
2
71877
Filter for UDD-24-60-HC
25
71900
Handle of Compressor Unit Installation
Board for UDD-24-60-HC
71855
Inner Drain Pan for UDD-24-60-HC
3
71878
Lateral Cover of Machine Room for
UDD-24-60-HC
26
71901
Ballast of Light for UDD-24-60-HC
49
71856
Evaporator for UDD-24-60-HC
4
71879
Front Cover of Machine Room for UDD24-60-HC
27
71902
Condenser Bracket for UDD-24-60-HC
50
71857
Fan Motor Installation Panel for UDD24-60-HC
5
71880
Left Solid Door for UDD-24-60-HC
28
71903
Temperature Display for UDD-24-60-HC
51
71858
Evaporator Fan Motor for UDD-24-60-HC
6
71881
Solid Door Gasket for UDD-24-60-HC
29
71904
Transformer of Temperature Display for
UDD-24-60-HC
52
71859
Evaporator Fan Motor Holder for UDD24-60-HC
7
71882
Right Solid Door for UDD-24-60-HC
30
71905
Transformer Bracket of Temperature
Display for UDD-24-60-HC
53
71860
Blade of Evaporator Fan Motor for
UDD-24-60-HC
8
71883
Axis Sleeve for UDD-24-60-HC
31
71906
Sensor of Temperature Display for
UDD-24-60-HC
54
71861
Evaporator Cover for UDD-24-60-HC
9
71884
Bottom Right Hinge for UDD-24-60-HC
32
71907
Spring Hinge for UDD-24-60-HC
55
71862
Temperature Control Panel for UDD24-60-HC
10
71885
Bottom Left Hinge for UDD-24-60-HC
33
71908
Beer Tower for UDD-24-60-HC
56
71863
Mechanical Thermostat for UDD-2460-HC
11
71886
Upper Right Hinge for UDD-24-60-HC
34
71909
Cover of Top Tray for UDD-24-60-HC
57
71864
Temperature Control Knob for UDD24-60-HC
12
71887
Upper Left Hinge for UDD-24-60-HC
35
71910
Cover of CO2 Line for UDD-24-60-HC
58
71865
Light Switch for UDD-24-60-HC
13
71888
Plate of Lock for Right Door for UDD24-60-HC
36
71911
Cover of L Shape Connector for UDD24-60-HC
59
71866
Bracket of Lateral Cover for UDD-2460-HC
14
71889
Bottom Gasket of Compressor for UDD24-60-HC
37
71912
Drain Hose of Top Tray for UDD-2460-HC
60
71867
Compressor Unit Installation Board for
UDD-24-60-HC
15
71890
Fixed Block for Worktop for UDD-2460-HC
38
71913
L Shape Connector for UDD-24-60-HC
61
71868
Condenser for UDD-24-60-HC
16
71891
K Strip-4 Holes for UDD-24-60-HC
39
71914
Rubber Pad for UDD-24-60-HC
62
63
71869
Compressor for UDD-24-60-HC
17
71892
K Clip for UDD-24-60-HC
40
71915
Drain Connector of Top Tray for UDD24-60-HC
71870
Wiring Box of Compressor for UDD24-60-HC
18
71893
Shelf for UDD-24-60-HC
41
71916
Drain Connector Nut of Top Tray for
UDD-24-60-HC
64
71871
Start Capacitor for UDD-24-60-HC
19
71894
LED Light for UDD-24-60-HC
42
71917
Air Tube of Left Beer Tower for UDD24-60-HC
65
71872
Overload Protector for UDD-24-60-HC
20
71895
Drain Hose for UDD-24-60-HC
43
71918
Air Tube of Right Beer Tower for UDD24-60-HC
66
71873
Starter for UDD-24-60-HC
21
71896
Power Cord for UDD-24-60-HC
44
71778
Short Drain Hose of Top Tray for UDD24-60-HC
67
71874
Condenser Fan Motor for UDD-24-60-HC
22
71897
Adjusted Feet for UDD-24-60-HC
45
71779
T Shape Connector for UDD-24-60-HC
68
71875
Outer Drain Pan for UDD-24-60-HC
23
71898
Stop Block of Compressor Unit
Installation Board for UDD-24-60-HC
46
24
Parts Breakdown
Model BD-CN-0023-HC 50068
25
Parts Breakdown
Model BD-CN-0023-HC 50068
Item No.
Description
Position
Item No.
Description
Position
Item No.
Description
Position
48
71769
Cabinet for UDD-3-HC
1
26189
Filter D25x140 for UDD-3-HC
25
71835
Handle of Compressor Unit Installation
Board for UDD-3-HC
71770
Top Board for UDD-3-HC
2
71761
Lateral Cover for UDD-3-HC
26
71836
Ballast for UDD-3-HC
49
27
71837
Condenser Installation Board for
UDD-3-HC
50
28
27067
Temp Display for UDD-3-HC
51
52
37685
Inner Drain Pan for UDD-3-HC
3
37708
Front Cover of Machine Room for
UDD-3-HC
71757
Evaporator for UDD-3-HC
4
71762
Left Door (Solid) for UDD-3-HC
71771
Fan Motor Installation Panel for UDD3-HC
5
71763
Door Gasket (Solid) for UDD-3-HC
29
71839
Transformer for Temp Display for
UDD-3-HC
37688
Evaporator Fan Motor for UDD-3-HC
6
71764
Right Door (Solid) for UDD-3-HC
30
71840
Temp Display Transformer Holder for
UDD-3-HC
53
37689
Evaporator Fan Motor Holder for
UDD-3-HC
7
26760
Axis Sleeve for UDD-3-HC
31
71841
Temp Sensor for Temp Display for
UDD-3-HC
54
37690
Evaporator Fan Motor Blade for UDD3-HC
8
37728
Lower Right Hinge for UDD-3-HC
32
26164
Spring Hinge for UDD-3-HC
55
71772
Evaporator Cover for UDD-3-HC
9
37730
Lower Left Hinge for UDD-3-HC
33
71843
Beer Tower for UDD-3-HC
56
37693
Temperature Control Panel for UDD3-HC
10
37731
Upper Right Hinge for UDD-3-HC
34
71844
Cover of Top Tray for UDD-3-HC
57
37694
Temperature Controller for UDD-3-HC
11
37732
Upper Left Hinge for UDD-3-HC
35
71845
CO2 Pipe Hole Cover for UDD-3-HC
58
37697
Lamp Switch for UDD-3-HC
13
37734
Plate of Lock for UDD-3-HC
36
73078
Bottom Drain Plug Cover for UDD-3-HC
59
71760
Bracket of Lateral Cover for UDD-3-HC
14
73077
Rubber Base of Compressor for UDD3-HC
37
71847
Drain Hose of Top Tray (Long) for
UDD-3-HC
60
37699
Compressor Unit Installation Board for
UDD-3-HC
15
37735
Fixed Block of Top Board for UDD-3-HC
38
71848
L Shape Connector for UDD-3-HC
61
37700
Condenser 4R11K150L for UDD-3-HC
16
37736
K Strip 4 Holes for UDD-3-HC
39
71775
Rubber Pad for UDD-3-HC
62
26183
Compressor NE6187Z for UDD-3-HC
17
26884
K Clip for UDD-3-HC
40
73079
Beer Tray Drain Plug for UDD-3-HC
63
37701
Splice Box for UDD-3-HC
18
71774
Shelf (Left & Right) for UDD-3-HC
41
73080
Beer Tray Drain Plug Nut for UDD-3-HC
64
37702
Start Capacitor for UDD-3-HC
19
37741
LED Bulb for UDD-3-HC
42
71776
Air Pipe (Short) for UDD-3-HC
65
37703
Overload Protector for UDD-3-HC
20
26203
Drain Hose φ16 for UDD-3-HC
43
71777
Air Pipe (Long) for UDD-3-HC
66
37704
Starter for UDD-3-HC
21
26205
Power Cord 16AWG for UDD-3-HC
44
71778
Drain Hose of Top Tray (Short) for
UDD-3-HC
67
37705
Condenser Fan Motor RAM4715 for
UDD-3-HC
22
28236
Adjustable Feet M12x45 for UDD-3-HC
45
71779
T Shape Connector for UDD-3-HC
68
37706
Outer Drain Pan for UDD-3-HC
23
37754
Installation Board Limited Block for
UDD-3-HC
46
71780
Middle Beam Cover for UDD-3-HC
69
26188
Filter Base D25 for UDD-3-HC
24
71834
K Strip 2 Holes for UDD-3-HC
47
26
Parts Breakdown
Model BB-CN-0020-DH 50065
27
Parts Breakdown
Model BB-CN-0020-DH 50065
Item No.
Description
Position
Item No.
Description
Position
Item No.
Description
Position
71919
Cabinet for UDD-24-72-HC
1
71942
Filter Fixer for UDD-24-72-HC
24
71965
K Strip-2 Holes for UDD-24-72-HC
47
48
71920
Top Board for UDD-24-72-HC
2
71943
Filter for UDD-24-72-HC
25
71966
Handle of Compressor Unit Installation
Board for UDD-24-72-HC
71921
Inner Drain Pan for UDD-24-72-HC
3
71944
Lateral Cover of Machine Room for
UDD-24-72-HC
26
71967
Ballast of Light for UDD-24-72-HC
49
71922
Evaporator for UDD-24-72-HC
4
71945
Front Cover of Machine Room for UDD24-72-HC
27
71968
Condenser Bracket for UDD-24-72-HC
50
71923
Fan Motor Installation Panel for UDD24-72-HC
5
71946
Left Solid Door for UDD-24-72-HC
28
71969
Temperature Display for UDD-24-72-HC
51
71924
Evaporator Fan Motor for UDD-24-72-HC
6
71947
Solid Door Gasket for UDD-24-72-HC
29
71970
Transformer of Temperature Display for
UDD-24-72-HC
52
71925
Evaporator Fan Motor Holder for UDD24-72-HC
7
71948
Right Solid Door for UDD-24-72-HC
30
71971
Transformer Bracket of Temperature
Display for UDD-24-72-HC
53
71926
Blade of Evaporator Fan Motor for
UDD-24-72-HC
8
71949
Axis Sleeve for UDD-24-72-HC
31
71972
Sensor of Temperature Display for
UDD-24-72-HC
54
71927
Evaporator Cover for UDD-24-72-HC
9
71950
Bottom Right Hinge for UDD-24-72-HC
32
71973
Spring Hinge for UDD-24-72-HC
55
71928
Temperature Control Panel for UDD24-72-HC
10
71951
Bottom Left Hinge for UDD-24-72-HC
33
71974
Beer Tower for UDD-24-72-HC
56
71929
Mechanical Thermostat for UDD-2472-HC
11
71952
Upper Right Hinge for UDD-24-72-HC
34
71975
Cover of Top Tray for UDD-24-72-HC
57
71930
Temperature Control Knob for UDD24-72-HC
12
71953
Upper Left Hinge for UDD-24-72-HC
35
71976
Cover of CO2 Line for UDD-24-72-HC
58
71931
Light Switch for UDD-24-72-HC
13
71954
Plate of Lock for Right Door for UDD24-72-HC
36
71977
Cover of L Shape Connector for UDD24-72-HC
59
71932
Bracket of Lateral Cover for UDD-2472-HC
14
71955
Bottom Gasket of Compressor for UDD24-72-HC
37
71978
Drain Hose of Top Tray for UDD-2472-HC
60
71933
Compressor Unit Installation Board for
UDD-24-72-HC
15
71956
Fixed Block for Worktop for UDD-2472-HC
38
71979
L Shape Connector for UDD-24-72-HC
61
71934
Condenser for UDD-24-72-HC
16
71957
K Strip-4 Holes for UDD-24-72-HC
39
71980
Rubber Pad for UDD-24-72-HC
62
63
71935
Compressor for UDD-24-72-HC
17
71958
K Clip for UDD-24-72-HC
40
71981
Drain Connector of Top Tray for UDD24-72-HC
71936
Wiring Box of Compressor for UDD24-72-HC
18
71959
Shelf for UDD-24-72-HC
41
71982
Drain Connector Nut of Top Tray for
UDD-24-72-HC
64
71937
Start Capacitor for UDD-24-72-HC
19
71960
LED Light for UDD-24-72-HC
42
71983
Air Tube of Left Beer Tower for UDD24-72-HC
65
71938
Overload Protector for UDD-24-72-HC
20
71961
Drain Hose for UDD-24-72-HC
43
71984
Air Tube of Right Beer Tower for UDD24-72-HC
66
71939
Starter for UDD-24-72-HC
21
71962
Power Cord for UDD-24-72-HC
44
71985
Middle Shelf for UDD-24-72-HC
67
71940
Condenser Fan Motor for UDD-24-72-HC
22
71963
Adjusted Feet for UDD-24-72-HC
45
71964
Stop Block of Compressor Unit
Installation Board for UDD-24-72-HC
46
71941
Outer Drain Pan for UDD-24-72-HC
23
28
Parts Breakdown
Model BD-CN-0032-HC 50069
29
Parts Breakdown
Model BD-CN-0032-HC 50069
Item No.
Description
Position
Item No.
Description
Position
Item No.
Description
Position
48
71781
Cabinet for UDD-4-HC
1
26189
Filter D25x140 for UDD-4-HC
25
71835
Handle of Compressor Unit Installation
Board for UDD-4-HC
71782
Top Board for UDD-4-HC
2
71761
Lateral Cover for UDD-4-HC
26
71836
Ballast for UDD-4-HC
49
27
71837
Condenser Installation Board for
UDD-4-HC
50
28
27067
Temp Display for UDD-4-HC
51
52
37685
Inner Drain Pan for UDD-4-HC
3
37708
Front Cover of Machine Room for
UDD-4-HC
71757
Evaporator for UDD-4-HC
4
71762
Left Door (Solid) for UDD-4-HC
71758
Fan Motor Installation Panel for UDD4-HC
5
71763
Door Gasket (Solid) for UDD-4-HC
29
71839
Transformer for Temp Display for
UDD-4-HC
37688
Evaporator Fan Motor for UDD-4-HC
6
71764
Right Door (Solid) for UDD-4-HC
30
71840
Temp Display Transformer Holder for
UDD-4-HC
53
37689
Evaporator Fan Motor Holder for
UDD-4-HC
7
26760
Axis Sleeve for UDD-4-HC
31
71841
Temp Sensor for Temp Display for
UDD-4-HC
54
37690
Evaporator Fan Motor Blade for UDD4-HC
8
37728
Lower Right Hinge for UDD-4-HC
32
26164
Spring Hinge for UDD-4-HC
55
71759
Evaporator Cover for UDD-4-HC
9
37730
Lower Left Hinge for UDD-4-HC
33
71843
Beer Tower for UDD-4-HC
56
37693
Temperature Control Panel for UDD4-HC
10
37731
Upper Right Hinge for UDD-4-HC
34
71844
Cover of Top Tray for UDD-4-HC
57
37694
Temperature Controller for UDD-4-HC
11
37732
Upper Left Hinge for UDD-4-HC
35
71845
CO2 Pipe Hole Cover for UDD-4-HC
58
37697
Lamp Switch for UDD-4-HC
13
37734
Plate of Lock for UDD-4-HC
36
73082
Bottom Drain Plug Cover for UDD-4-HC
59
71760
Bracket of Lateral Cover for UDD-4-HC
14
73081
Rubber Base of Compressor for UDD4-HC
37
73085
Drain Hose of Top Tray (Long) for
UDD-4-HC
60
37699
Compressor Unit Installation Board for
UDD-4-HC
15
37735
Fixed Block of Top Board for UDD-4-HC
38
71848
L Shape Connector for UDD-4-HC
61
37700
Condenser 4R11K150L for UDD-4-HC
16
37736
K Strip 4 Holes for UDD-4-HC
39
71784
Rubber Pad for UDD-4-HC
62
26280
Compressor NEK6214Z for UDD-4-HC
17
26884
K Clip for UDD-4-HC
40
73083
Beer Tray Drain Plug for UDD-4-HC
63
37701
Splice Box for UDD-4-HC
18
71783
Shelf (Left & Right) for UDD-4-HC
41
73084
Beer Tray Drain Plug Nut for UDD-4-HC
64
37702
Start Capacitor for UDD-4-HC
19
37741
LED Bulb for UDD-4-HC
42
71785
Air Pipe (Short) for UDD-4-HC
65
37703
Overload Protector for UDD-4-HC
20
26203
Drain Hose φ16 for UDD-4-HC
43
71786
Air Pipe (Long) for UDD-4-HC
66
37704
Starter for UDD-4-HC
21
26205
Power Cord 16AWG for UDD-4-HC
44
71847
Drain Hose of Top Tray (Short) for
UDD-4-HC
67
37705
Condenser Fan Motor RAM4715 for
UDD-4-HC
22
28236
Adjustable Feet M12x45 for UDD-4-HC
45
73086
T Shape Connector for UDD-4-HC
68
37706
Outer Drain Pan for UDD-4-HC
23
28311
Installation Board Limited Block for
UDD-4-HC
46
71787
Middle Beam Cover for UDD-4-HC
69
26188
Filter Base D25 for UDD-4-HC
24
71834
K Strip 2 Holes for UDD-4-HC
47
30
Electrical Schematics
Model BD-CN-0007-HC 50066
31
Electrical Schematics
Model BB-CN-0012-DH 50063
32
Electrical Schematics
Model BD-CN-0019-HC 50067
33
Electrical Schematics
Model BB-CN-0016-DH 50064
34
Electrical Schematics
Model BD-CN-0023-HC 50068
35
Electrical Schematics
Model BB-CN-0020-DH 50065
36
Electrical Schematics
Model BD-CN-0032-HC 50069
37
Notes
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
38
Warranty Registration
Thank you for purchasing an Omcan product. To register your warranty for this product, complete the information below, tear off the card at
the perforation and then send to the address specified below. You can also register online by visiting:
Merci d’avoir acheté un produit Omcan. Pour enregistrer votre garantie pour ce produit, complétez les informations ci-dessous, détachez la
carte au niveau de la perforation, puis l’envoyer à l’adresse spécifié ci-dessous. Vous pouvez également vous inscrire en ligne en visitant:
Gracias por comprar un producto Omcan usted. Para registrar su garantía para este producto, complete la información a continuación,
cortar la tarjeta en la perforación y luego enviarlo a la dirección indicada a continuación. También puede registrarse en línea en:
www.omcan.com/warrantyregistration.html
For mailing in Canada
For mailing in the US
Pour postale au Canada
Pour diffusion aux États-Unis
Por correo en Canadá
Por correo en los EE.UU.
OMCAN
OMCAN
PRODUCT WARRANTY REGISTRATION
3115 Pepper Mill Court,
Mississauga, Ontario
PRODUCT WARRANTY REGISTRATION
4450 Witmer Industrial Estates, Unit 4,
Niagara Falls, New York
Canada, L5L 4X5
USA, 14305
or email to: service@omcan.com

Purchaser’s Information
Name:
Company Name:
Address:
Telephone:
City:
Province or State:
Postal or Zip:
Country:
Email Address:
Type of Company:
Dealer from which Purchased:
Dealer City:
Dealer Province or State:
Restaurant
Bakery
Deli
Butcher
Supermarket
Caterer
Institution (specify):
Invoice:
Other (specify):
Model Name:
Model Number:
Serial Number:
Machine Description:
Date of Purchase (MM/DD/YYYY):
Would you like to extend the warranty?
Date of Installation (MM/DD/YYYY):
Yes
No
Thank you for choosing Omcan | Merci d’avoir choisi Omcan | Gracias por elegir Omcan
39
Since 1951 Omcan has grown to become a leading distributor of equipment and supplies to the North
American food service industry. Our success over these many years can be attributed to our commitment
to strengthen and develop new and existing relationships with our valued customers and manufacturers.
Today with partners in North America, Europe, Asia and South America, we continually work to improve
and grow the company. We strive to offer customers exceptional value through our qualified local sales
and service representatives who provide convenient access to over 3, 500 globally sourced products.
Depuis 1951 Omcan a grandi pour devenir un des “leaders” de la distribution des équipements et
matériel pour l’industrie des services alimentaires en Amérique du Nord. Notre succès au cours de ces
nombreuses années peut être attribué à notre engagement à renforcer et à développer de nouvelles
et existantes relations avec nos clients et les fabricants de valeur. Aujourd’hui avec des partenaires en
Amérique du Nord, Europe, Asie et Amérique du Sud, nous travaillons continuellement à améliorer et
développer l’entreprise. Nous nous efforçons d’offrir à nos clients une valeur exceptionnelle grâce à
nos ventes locales qualifiées et des représentants de service qui offrent un accès facile à plus de 3500
produits provenant du monde entier.
Desde 1951 Omcan ha crecido hasta convertirse en un líder en la distribución de equipos y suministros
de alimentos en América del Norte industria de servicios. Nuestro éxito en estos años se puede atribuir
a nuestro compromiso de fortalecer y desarrollar nuevas relaciones existentes con nuestros valiosos
clientes y fabricantes. Hoy con socios de América del Norte, Europa, Asia y América del Sur, que trabajan
continuamente para mejorar y crecer la empresa. Nos esforzamos por ofrecer a nuestros clientes valor
excepcional a través de nuestro local de ventas y representantes de los servicios que proporcionan un
fácil acceso a más de 3, 500 productos con origen a nivel mundial.
Download PDF
Similar pages