Cisco UCS C220 M4 SFF Rack Server Spec Sheet

Spec Sheet
Cisco UCS C220 M4
High-Density Rack Server
(Small Form Factor Disk
Drive Model)
CISCO SYSTEMS
170 WEST TASMAN DR
SAN JOSE, CA, 95134
WWW.CISCO.COM
PUBLICATION HISTORY
REV C.9
JULY 28, 2016
OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
DETAILED VIEWS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Chassis Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Chassis Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
BASE SERVER STANDARD CAPABILITIES and FEATURES . . . . . . . . . . . . . . . . . 8
CONFIGURING the SERVER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
STEP 1 VERIFY SERVER SKU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
STEP 2 SELECT CPU(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
STEP 3 SELECT MEMORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
STEP 4 SELECT RAID CONTROLLERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
RAID Controller Options (internal HDD/SSD support) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Embedded Software RAID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Cisco 12G SAS Modular RAID Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
SAS HBA (internal HDD/SSD/JBOD support) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
SAS HBA (external JBOD support) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
RAID Volumes and Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
STEP 5 SELECT HARD DISK DRIVES (HDDs) or SOLID STATE DRIVES (SSDs) . . . . . . . . . . . . . 33
STEP 6 SELECT PCIe OPTION CARD(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
STEP 7 ORDER OPTIONAL NETWORK CARD ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . 40
STEP 8 ORDER POWER SUPPLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
STEP 9 SELECT AC POWER CORD(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
STEP 10 ORDER TOOL-LESS RAIL KIT AND OPTIONAL REVERSIBLE CABLE MANAGEMENT ARM . 49
STEP 11 SELECT NIC MODE (OPTIONAL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
STEP 12 ORDER A TRUSTED PLATFORM MODULE (OPTIONAL) . . . . . . . . . . . . . . . . . . . . . 51
STEP 13 ORDER CISCO FLEXIBLE FLASH SD CARD MODULE (OPTIONAL) . . . . . . . . . . . . . . . 53
STEP 14 ORDER OPTIONAL USB 3.0 DRIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
STEP 15 SELECT OPERATING SYSTEM AND VALUE-ADDED SOFTWARE . . . . . . . . . . . . . . . . 55
STEP 16 SELECT OPERATING SYSTEM MEDIA KIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
STEP 17 SELECT SERVICE and SUPPORT LEVEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
OPTIONAL STEP - ORDER RACK(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
OPTIONAL STEP - ORDER PDU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
SUPPLEMENTAL MATERIAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
CHASSIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
CPUs and DIMMs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Physical Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Memory Population Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
DIMM Population Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Recommended Memory Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Additional DIMM Populations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
RAID Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
RAID Option ROM (OPROM) Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Embedded SATA RAID: Two SATA Controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Serial Port Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Upgrade and Servicing-Related Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Adding an Additional CPU (with CPU heat sink) or Replacing CPUs . . . . . . . . . . . . . . 81
Motherboard Lithium Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Thermal Grease (with syringe applicator) for CPU to Heatsink Seal . . . . . . . . . . . . . . 81
Air Baffle Replacement Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
CPU Heat Sink Cleaning Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
RACKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
PDUs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
2
Cisco UCS C220 M4 High-Density Rack Server Small Form Factor Disk Drive Model)
CONTENTS
KVM CABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Motherboard USB and SD Ports, and RAID Card Backup Location . . . . . . . . . . . . . . . . . . . . 87
TECHNICAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Dimensions and Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Power Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Compliance Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Cisco UCS C220 M4 High-Density Rack Server Small Form Factor Disk Drive Model)
3
4
Cisco UCS C220 M4 High-Density Rack Server Small Form Factor Disk Drive Model)
OVERVIEW
OVERVIEW
The Cisco® UCS C220 M4 SFF rack server is the newest 2-socket, 1U rack server from Cisco, designed for
both performance and expandability over a wide range of storage-intensive infrastructure workloads from
web serving to distributed database.
The enterprise-class UCS C220 M4 SFF server extends the capabilities of Cisco’s Unified Computing System
portfolio in a 1U form factor with the addition of the Intel Xeon E5-2600 v3 and v4 series processor family
that deliver significant performance and efficiency gains. In addition, the UCS C220 M4 SFF server provides
24 DIMM slots, up to 8 drives and 2 x 1 GbE LAN-on-motherboard (LOM) ports delivering outstanding levels of
density and performance in a compact 1U package.
The C220 M4 SFF server includes a modular LAN on motherboard (mLOM) slot for installation of a Cisco
Virtual Interface Card (VIC) or third-party network interface card (NIC) without consuming a PCI slot in
addition to 2 x 1 GbE embedded (on the motherboard). These features combine to provide outstanding
levels of internal memory and storage expandability along with exceptional performance.
The Cisco UCS C220 M4 SFF server can be used standalone, or as part of the Cisco Unified Computing
System, which unifies computing, networking, management, virtualization, and storage access into a single
integrated architecture enabling end-to-end server visibility, management, and control in both bare metal
and virtualized environments.
Figure 1
Cisco UCS C220 M4 High-Density SFF Rack Server
Front View
Rear View
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
5
DETAILED VIEWS
DETAILED VIEWS
Chassis Front View
Figure 2 shows the front view of the Cisco UCS C220 M4 High-Density SFF Rack Server.
Figure 2
Chassis Front View
4
5
7
6
9
8
10
3
HDD 01
HDD 04
HDD 02
HDD 05
HDD 03
HDD 06
HDD 07
HDD 08
1
352973
2
11
1
Drives (up to eight 2.5-inch drives)
7
Fan status LED
2
Pull-out asset tag
8
Temperature status LED
3
Operations panel buttons and LEDs
9
Power supply status LED
4
Power button/Power status LED
10
Network link activity LED
5
Unit identification button/LED
11
KVM connector (used with KVM cable that
provides two USB 2.0, one VGA, and one
serial connector)1
6
System status LED
Notes . . .
1. For more information about the KVM cable connection, see KVM CABLE, page 86
6
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
DETAILED VIEWS
Chassis Rear View
Figure 3 shows the external features of the rear panel.
Chassis Rear View
1
2
PCIe 01
PCIe 02
PSU 01
PSU 02
mLOM
3
4
5
6
7
8
9
10
352977
Figure 3
11
1
PCIe riser 1/slot 1
7
Serial port (RJ-45 connector)1
2
PCIe riser 2/slot 2
8
Two embedded (on the motherboard) Intel
i350 GbE Ethernet controller ports
LAN1 is left connector and
LAN2 is right connector
3
Modular LAN-on-motherboard (mLOM)
card slot
9
VGA video port (DB-15)
4
Grounding-lug hole (for DC power supplies)
10
Rear unit identification button/LED
5
USB 3.0 ports (two)
11
Power supplies (up to two, redundant as 1+1)
6
1-Gb Ethernet dedicated management port
Notes . . .
1. For details of the serial port pinout, see Serial Port Details, page 79.
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
7
BASE SERVER STANDARD CAPABILITIES and FEATURES
BASE SERVER STANDARD CAPABILITIES and FEATURES
Table 1 lists the capabilities and features of the base server. Details about how to configure the server for
a particular feature or capability (for example, number of processors, disk drives, or amount of memory)
are provided in CONFIGURING the SERVER, page 14.
Table 1 Capabilities and Features
Capability/Feature
Description
Chassis
One rack unit (1RU) chassis
CPU
One or two Intel® Xeon E5-2600 v3 or v4 series processor family CPUs
Chipset
Intel® C610 series chipset
Memory
24 slots for registered DIMMs (RDIMMs) or load-reduced DIMMs (LRDIMMs)
Multi-bit Error
Protection
This server supports multi-bit error protection.
Embedded NIC
Two embedded (on the motherboard) Intel i350 GbE ports, supporting the
following:
Expansion slots
■
Pre-Execution Boot (PXE boot)
■
iSCSI boot
■
Checksum and segmentation offload
■
NIC teaming
■
Riser 1 (controlled by CPU 1):
• One full-height profile, 3/4-length slot with x24 connector and x16
lane
■
Riser 2 (controlled by CPU 2):
• One half-height profile, half-length slot with x24 connector and x16
lane, or
• One half-height profile, half-length slot with x24 connector and x8
lane and two mini-SAS HD connectors that support two front-mount
PCIe Gen 3 NVMe PCIe SSDs.
■
Dedicated RAID controller slot (see Figure 6 on page 66)
• An internal slot is reserved for use by the Cisco 12G SAS Modular RAID
controller or the Cisco 12 Gbps Modular SAS HBA.
8
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
BASE SERVER STANDARD CAPABILITIES and FEATURES
Table 1 Capabilities and Features (continued)
Capability/Feature
Description
Internal storage devices
Drives are installed into front-panel drive bays that provide hot-pluggable
access.
• Small Form Factor (SFF) drives. Up to eight 2.5-inch SAS or SATA
hot-swappable hard disk drives (HDDs) or solid state drives (SSDs).
• NVMe PCIe SSD drives. These drives can placed in front drive bays 1
and 2 only.
Cisco Flexible Flash
drives
■
The server also contains one internal USB 3.0 port on the motherboard
that you can use with an optional 16 GB USB thumb drive for additional
storage
■
UCS Storage Accelerators are also available. These PCIe flash storage
devices provide independent high-speed storage.
The server supports up to two internal 32 GB or two internal 64 GB Cisco
Flexible Flash drives (SD cards).
The second SD card is blank and can be used to mirror the first SD card. It
can be used to protect the Hypervisor Partition with RAID1.
Video
The Cisco Integrated Management Controller (CIMC) provides video using the
Matrox G200e video/graphics controller:
■
■
Integrated 2D graphics core with hardware acceleration
DDR2/3 memory interface supports up to 512 MB of addressable memory
(8 MB is allocated by default to video memory)
■
Supports display resolutions up to 1920 x 1200 16bpp @ 60Hz
■
High-speed integrated 24-bit RAMDAC
■
Single lane PCI-Express host interface running at Gen 1 speed
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
9
BASE SERVER STANDARD CAPABILITIES and FEATURES
Table 1 Capabilities and Features (continued)
Capability/Feature
Interfaces
Description
■
Rear panel
• One DB15 VGA connector
• One RJ45 serial port connector
• Two USB 3.0 port connectors
• One RJ-45 10/100/1000 Ethernet management port, using Cisco
Integrated Management Controller (CIMC) firmware
• Two Intel i350 embedded (on the motherboard) GbE LOM ports
• One flexible modular LAN on motherboard (mLOM) slot that can
accommodate various interface cards
■
Front panel
• One KVM console connector (supplies two USB 2.0 connectors, one
VGA DB15 connector, and one serial port (RS232) RJ45 connector)
■
Various PCIe card ports (dependent on which cards are installed)
• Virtual Interface Card (VIC) ports
• Converged Network Adapter (CNA) ports
• Network Interface Card (NIC) ports
• Host Bus Adapter (HBA) ports
10
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
BASE SERVER STANDARD CAPABILITIES and FEATURES
Table 1 Capabilities and Features (continued)
Capability/Feature
Storage controller
Description
■
Embedded Software RAID (6 Gbps)
• Embedded SATA-only RAID controller, supporting up to 8 SATA-only
drives (RAID 0, 1, 10), or
• Embedded Software RAID 5 key upgrade, supporting up to 8
SATA-only drives (RAID 0, 1, 10, 5)
■
Cisco 12G SAS Modular RAID controller card with internal SAS
connectivity.
• Supports up to 24 internal drives (note however that this server can
be configured with a maximum of 8 drives)
• Plugs into a dedicated internal RAID controller slot
• Can be purchased alone, or along with an onboard Flash-Backed
Write Cache (FBWC) upgrade option, as shown in the table below
RAID Card Version
Supported RAID Levels
Onboard FBWC
(cache)
UCSC-MRAID12G1
JBOD, 0, 1, 10
None
UCSC-MRAID12G-5122
JBOD, 0, 1, 5, 50
UCSC-MRAID12G-1GB2
JBOD, 0, 1, 10, 5, 6, 50, 60
1 GB
UCSC-MRAID12G-2GB2
JBOD, 0, 1, 10, 5, 6, 50, 60
2 GB
UCSC-MRAID12G-4GB2
JBOD, 0, 1, 10, 5, 6, 50, 60
4 GB
512 MB
Notes . . .
1. Base RAID controller card (RAID 0, 1, 10 only)
2. FBWC option for base RAID controller card (adding the FBWC option extends the
RAID levels)
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
11
BASE SERVER STANDARD CAPABILITIES and FEATURES
Table 1 Capabilities and Features (continued)
Capability/Feature
Storage controller
Description
■
Cisco 12 Gbps Modular SAS HBA with internal SAS connectivity
• Supports up to 24 internal drives (note however that this server can
be configured with a maximum of 8 drives)
• Plugs into a dedicated internal RAID controller slot
• Supports JBOD only, not RAID, as shown in the below table.
HBA Card Version
Supported RAID Levels
UCSC-SAS12GHBA
JBOD only
■
Cisco 9300-8E 12G SAS HBA with external SAS connectivity
• Provides 8 external SAS ports
• Plugs into a PCIe slot at the rear of the server
• No FBWC (cache) or cache power backup
• SAS 3.0 compliant
WoL
The 1-Gb Base-T Ethernet LAN ports support the wake-on-LAN (WoL)
standard.
Front Panel
A front panel controller provides status indications and control buttons
Modular LAN on
Motherboard (mLOM)
slot
The mLOM slot can flexibly accommodate the following cards:
■
Cisco Virtual Interface Cards (VIC)
■
Quad Port Intel i350 1GbE RJ45 Network Interface Card (NIC)
NOTE: The four Intel i350 ports are provided on an optional card
that plugs into the mLOM slot, and are separate from the two
embedded (on the motherboard) LAN ports.
Power subsystem
Up to two 770 W (AC) hot swappable power supplies or two 1050 W (DC)
power supplies. One is mandatory; one more can be added for 1 + 1
redundancy.
ACPI
This server supports the advanced configuration and power interface (ACPI)
4.0 standard.
Fans
Chassis:
■
12
Six hot-swappable fans for front-to-rear cooling
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
BASE SERVER STANDARD CAPABILITIES and FEATURES
Table 1 Capabilities and Features (continued)
Capability/Feature
Description
Integrated management
processor
Baseboard Management Controller (BMC) running Cisco Integrated
Management Controller (CIMC) firmware.
Depending on your CIMC settings, the CIMC can be accessed through the
1-GbE dedicated management port, the 1-GbE LOM ports, or a Cisco virtual
interface card (VIC).
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
13
CONFIGURING the SERVER
CONFIGURING the SERVER
Follow these steps to configure the Cisco UCS C220 M4 High-Density SFF Rack Server:
14
■
STEP 1 VERIFY SERVER SKU, page 15
■
STEP 2 SELECT CPU(s), page 16
■
STEP 3 SELECT MEMORY, page 19
■
STEP 4 SELECT RAID CONTROLLERS, page 25
■
STEP 5 SELECT HARD DISK DRIVES (HDDs) or SOLID STATE DRIVES (SSDs), page 33
■
STEP 6 SELECT PCIe OPTION CARD(s), page 37
■
STEP 7 ORDER OPTIONAL NETWORK CARD ACCESSORIES, page 40
■
STEP 8 ORDER POWER SUPPLY, page 45
■
STEP 9 SELECT AC POWER CORD(s), page 46
■
STEP 10 ORDER TOOL-LESS RAIL KIT AND OPTIONAL REVERSIBLE CABLE MANAGEMENT
ARM, page 49
■
STEP 11 SELECT NIC MODE (OPTIONAL), page 50
■
STEP 12 ORDER A TRUSTED PLATFORM MODULE (OPTIONAL), page 51
■
STEP 13 ORDER CISCO FLEXIBLE FLASH SD CARD MODULE (OPTIONAL), page 53
■
STEP 14 ORDER OPTIONAL USB 3.0 DRIVE, page 54
■
STEP 15 SELECT OPERATING SYSTEM AND VALUE-ADDED SOFTWARE, page 55
■
STEP 16 SELECT OPERATING SYSTEM MEDIA KIT, page 58
■
STEP 17 SELECT SERVICE and SUPPORT LEVEL, page 59
■
OPTIONAL STEP - ORDER RACK(s), page 64
■
OPTIONAL STEP - ORDER PDU, page 65
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
CONFIGURING the SERVER
STEP 1
VERIFY SERVER SKU
Verify the product ID (PID) of the server as shown in Table 2.
Table 2 PID of the C220 M4 High-Density SFF Rack Base Server
Product ID (PID)
UCSC-C220-M4S
Description
UCS C220 M4 SFF, no CPU, memory, HDD, SSD, power supply, SD cards, PCIe
cards, or tool-less rail kit
The Cisco UCS C220 M4 SFF server:
■
Does not include power supply, CPU, memory, hard disk drives (HDDs), solid-state drives
(SSDs), SD cards, tool-less rail kit, or plug-in PCIe cards.
NOTE: Use the steps on the following pages to configure the server with
the components that you want to include.
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
15
CONFIGURING the SERVER
STEP 2
SELECT CPU(s)
The standard CPU features are:
■
Intel Xeon E5-2600 v3 and v4 series processor family CPUs
■
Intel C610 series chipset
Cache size of up to 55 MB
■
Select CPUs
The available CPUs are listed in Table 3.
Table 3 Available Intel CPUs
Product ID (PID)
Intel
Number
Clock
Freq
(GHz)
Power
(W)
Cache
Size
(MB)
Cores
QPI
Highest
DDR4 DIMM
Clock
Support
(MHz)1
E5-2600 v4 Series Processor Family CPUs
UCS-CPU-E52699E
E5-2699 v4
2.20
145
55
22
9.6 GT/s
2400
UCS-CPU-E52698E
E5-2698 v4
2.20
135
50
20
9.6 GT/s
2400
UCS-CPU-E52697AE
E5-2697A v4
2.60
145
40
16
9.6 GT/s
2400
UCS-CPU-E52697E
E5-2697 v4
2.30
145
45
18
9.6 GT/s
2400
UCS-CPU-E52695E
E5-2695 v4
2.10
120
45
18
9.6 GT/s
2400
UCS-CPU-E52690E
E5-2690 v4
2.60
135
35
14
9.6 GT/s
2400
UCS-CPU-E52683E
E5-2683 v4
2.10
120
40
16
9.6 GT/s
2400
UCS-CPU-E52680E
E5-2680 v4
2.40
120
35
14
9.6 GT/s
2400
UCS-CPU-E52667E
E5-2667 v4
3.20
135
25
8
9.6 GT/s
2400
UCS-CPU-E52660E
E5-2660 v4
2.00
105
35
14
9.6 GT/s
2400
UCS-CPU-E52650E
E5-2650 v4
2.20
105
30
12
9.6 GT/s
2400
UCS-CPU-E52650LE
E5-2650L v4
1.70
65
35
14
9.6 GT/s
2400
UCS-CPU-E52643E
E5-2643 v4
3.40
135
20
6
9.6 GT/s
2400
UCS-CPU-E52640E
E5-2640 v4
2.40
90
25
10
8.0 GT/s
2133
UCS-CPU-E52637E
E5-2637 v4
3.50
135
15
4
9.6 GT/s
2400
UCS-CPU-E52630E
E5-2630 v4
2.20
85
25
10
8/0 GT/s
2133
UCS-CPU-E52630LE
E5-2630L v4
1.80
55
25
8
8.0 GT/s
2133
UCS-CPU-E52623E
E5-2623 v4
2.60
85
10
4
8.0 GT/s
2133
UCS-CPU-E52620E
E5-2620 v4
2.10
85
20
8
8.0 GT/s
2133
UCS-CPU-E52609E
E5-2609 v4
1.70
85
20
8
6.4 GT/s
1866
UCS-CPU-E52658E
E5-2658 v4
2.30
105
35
14
9.6 GT/s
2400
16
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
CONFIGURING the SERVER
Table 3 Available Intel CPUs (continued)
Product ID (PID)
Intel
Number
Clock
Freq
(GHz)
Power
(W)
Cache
Size
(MB)
Cores
QPI
Highest
DDR4 DIMM
Clock
Support
(MHz)1
E5-2600 v3 Series Processor Family CPUs
UCS-CPU-E52699D
E5-2699 v3
2.30
145
45
18
9.6 GT/s
2133
UCS-CPU-E52698D
E5-2698 v3
2.30
135
40
16
9.6 GT/s
2133
UCS-CPU-E52697D
E5-2697 v3
2.60
145
35
14
9.6 GT/s
2133
UCS-CPU-E52695D
E5-2695 v3
2.30
120
35
14
9.6 GT/s
2133
UCS-CPU-E52690D
E5-2690 v3
2.60
135
30
12
9.6 GT/s
2133
UCS-CPU-E52683D
E5-2683 v3
2.00
120
35
14
9.6 GT/s
2133
UCS-CPU-E52680D
E5-2680 v3
2.50
120
30
12
9.6 GT/s
2133
UCS-CPU-E52670D
E5-2670 v3
2.30
120
30
12
9.6 GT/s
2133
UCS-CPU-E52667D
E5-2667 v3
3.20
135
20
8
9.6 GT/s
2133
UCS-CPU-E52660D
E5-2660 v3
2.60
105
25
10
9.6 GT/s
2133
UCS-CPU-E52658D
E5-2658 v3
2.20
105
30
12
9.6 GT/s
2133
UCS-CPU-E52650D
E5-2650 v3
2.30
105
25
10
9.6 GT/s
2133
UCS-CPU-E52650LD
E5-2650L v3
1.80
65
30
12
9.6 GT/s
1866
UCS-CPU-E52643D
E5-2643 v3
3.40
135
20
6
9.6 GT/s
2133
UCS-CPU-E52640D
E5-2640 v3
2.60
90
20
8
8.0 GT/s
1866
UCS-CPU-E52637D
E5-2637 v3
3.50
135
15
4
9.6 GT/s
2133
UCS-CPU-E52630D
E5-2630 v3
2.40
85
20
8
8.0 GT/s
1866
UCS-CPU-E52630LD
E5-2630L v3
1.80
55
20
8
8.0 GT/s
1866
UCS-CPU-E52623D
E5-2623 v3
3.00
105
10
4
8.0 GT/s
1866
UCS-CPU-E52620D
E5-2620 v3
2.40
85
15
6
8.0 GT/s
1866
UCS-CPU-E52609D2
E5-2609 v3
1.90
85
15
6
6.4 GT/s
1600
Notes . . .
1. If higher or lower speed DIMMs are selected than what is shown in the table for a given CPU, the DIMMs will be
clocked at the lowest common denominator of CPU clock and DIMM clock.
2. The E5-2609 v3 CPU does not support Intel Hyper-Threading or Intel Turbo Boost technologies.
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
17
CONFIGURING the SERVER
Approved Configurations
(1) 1-CPU configurations:
■
Select any one CPU listed in Table 3 on page 16.
(2) 2-CPU Configurations:
■
Select two identical CPUs from any one of the rows of Table 3 on page 16.
Caveats
■
You can select either one processor or two identical processors.
■
The selection of 1 or 2 CPUs depends on the desired server functionality. See the following
sections:
■
18
—
STEP 3 SELECT MEMORY, page 19 (memory mirroring section)
—
Table 9 on page 30 (RAID support table)
—
STEP 4 SELECT RAID CONTROLLERS, page 25
—
STEP 6 SELECT PCIe OPTION CARD(s), page 37
For optimal performance, select DIMMs with the highest clock speed for a given processor
(see Table 3 on page 16). If you select DIMMs whose speeds are lower or higher than that
shown in the tables, suboptimal performance will result.
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
CONFIGURING the SERVER
STEP 3
SELECT MEMORY
The standard memory features are:
■
■
—
Clock speed: 2400 or 2133 MHz
—
Ranks per DIMM: 1, 2, 4, or 8
—
Operational voltage: 1.2 V
—
Registered ECC DDR4 DIMMs (RDIMMs), TSV-RDMMS, or load-reduced ECC DDR4 DIMMs
(LRDIMMs)
Memory is organized with four memory channels per CPU, with up to three DIMMs per
channel, as shown in Figure 4.
Slot 2
Slot 3
Slot 3
Slot 2
Slot 1
C220 M4 SFF Memory Organization
Slot 1
Figure 4
DIMMs
A1
A2
A3
E3
E2
E1
Chan A
B1
B2
Chan E
B3
Chan B
C1
C2
CPU 2
Chan C
D1
D2
F2
F1
G3
G2
G1
H3
H2
H1
Chan F
CPU 1
C3
F3
Chan G
D3
Chan D
Chan H
24 DIMMS
1536 GB maximum memory (with 64 GB DIMMs)
4 memory channels per CPU,
up to 3 DIMMs per channel
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
19
CONFIGURING the SERVER
Select DIMMs and Memory Mirroring
Select the memory configuration and whether or not you want the memory mirroring option.
The available memory DIMMs and mirroring option are listed in Table 4.
NOTE: When memory mirroring is enabled, the memory subsystem simultaneously
writes identical data to two channels. If a memory read from one of the channels
returns incorrect data due to an uncorrectable memory error, the system
automatically retrieves the data from the other channel. A transient or soft error in
one channel does not affect the mirrored data, and operation continues unless there
is a simultaneous error in exactly the same location on a DIMM and its mirrored
DIMM. Memory mirroring reduces the amount of memory available to the operating
system by 50% because only one of the two populated channels provides data.
Table 4 Available DDR4 DIMMs
Product ID (PID)
PID Description
Voltage
Ranks
/DIMM
2400-MHz DIMM Options
UCS-MR-1X322RV-A
32GB DDR4-2400-MHz RDIMM/PC4-19200/dual rank/x4
1.2 V
2
UCS-MR-1X161RV-A
16GB DDR4-2400-MHz RDIMM/PC4-19200/single rank/x4
1.2 V
1
UCS-MR-1X081RV-A
8 GB DDR4-2400-MHz RDIMM/PC4-19200/single rank/x4
1.2 V
1
2133-MHz DIMM Options
UCS-MR-1X648RU-A1
64GB DDR4-2133-MHz TSV-RDIMM/PC4-17000/octal rank/x4
1.2 V
8
UCS-MR-1X322RU-A
32GB DDR4-2133-MHz RDIMM/PC4-17000/dual rank/x4
1.2 V
2
UCS-ML-1X324RU-A
32GB DDR4-2133-MHz LRDIMM/PC4-17000/quad rank/x4
1.2 V
4
UCS-MR-1X162RU-A
16GB DDR4-2133-MHz RDIMM/PC4-17000/dual rank/x4
1.2 V
2
UCS-MR-1X081RU-A
8GB DDR4-2133-MHz RDIMM/PC4-17000/single rank/x4
1.2 V
1
Memory Mirroring Option
N01-MMIRROR
Memory mirroring option
Notes . . .
1. Power capping is not supported when using 64GB TSV-RDIMMS.
Approved Configurations
(1) 1-CPU configuration without memory mirroring:
■
20
Select from 1 to 12 DIMMs. Refer to Memory Population Rules, page 69, for more detailed
information.
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
CONFIGURING the SERVER
(2) 1-CPU configuration with memory mirroring:
■
Total
Number
of
DIMMs
Select 2, 4, 8, or 12 identical DIMMs. The DIMMs will be placed by the factory as shown in the
following table.
CPU 1 DIMM Placement in Channels
(for identical dual-rank DIMMs for 3DPC or identical quad-rank DIMMs for 2DPC)
Blue Slots
Black Slots
White Slots
2
(A1, B1)
—
—
4
(A1,B1); (C1,D1)
—
—
8
(A1,B1); (C1,D1)
(A2,B2); (C2,D2)
12
(A1,B1); (C1,D1)
(A2,B2); (C2,D2)
■
(A3,B3); (C3,D3)
Select the memory mirroring option (N01-MMIRROR) as shown in Table 4 on page 20.
(3) 2-CPU configuration without memory mirroring:
■
Select from 1 to 12 DIMMs per CPU. Refer to Memory Population Rules, page 69, for more
detailed information.
(4) 2-CPU configuration with memory mirroring:
■
Number
of
DIMMs
per CPU
Select 2, 4, 8, or 12 identical DIMMs per CPU. The DIMMs will be placed by the factory as
shown in the following table.
CPU 1 DIMM Placement in Channels
(for identical dual-rank DIMMs for 3DPC or
identical quad-rank DIMMs for 2DPC)
CPU 2 DIMM Placement in Channels
(for identical dual-rank DIMMs for 3DPC or
identical quad-rank DIMMs for 2DPC)
Blue Slots
Black Slots
White Slots
Blue Slots
Black Slots
White Slots
2
(A1, B1)
—
—
(E1, F1)
—
—
4
(A1,B1);
(C1,D1)
—
—
(E1,F1);
(G1,H1)
—
—
8 (CPU1)
and 4
(CPU2)1
(A1,B1);
(C1,D1)
(A2,B2);
(C2,D2)
—
(E1,F1)
(E2, F2)
—
8
(A1,B1);
(C1,D1)
(A2,B2);
(C2,D2)
—
(E1,F1);
(G1,H1)
(E2,F2);
(G2,H2)
—
12
(A1,B1);
(C1,D1)
(A2,B2);
(C2,D2)
(A3, B3);
(C3, D3)
(E1,F1);
(G1,H1)
(E2,F2);
(G2,H2)
(E3,F3);
(G3,H3)
Notes . . .
1. Not recommended (for performance reasons)
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
21
CONFIGURING the SERVER
■
Select the memory mirroring option (N01-MMIRROR) as shown in Table 4 on page 20.
NOTE: System performance is optimized when the DIMM type and quantity are equal
for both CPUs, and when all channels are filled equally across the CPUs in the server.
Caveats
■
System speed is dependent on how many DIMMs are populated per channel and the CPU
DIMM speed support. See Table 5 for details.
Table 5 2133-MHz DIMM Memory Speeds with Different CPUs
1600-MHz Capable CPU 1866-MHz Capable CPU 2133-MHz Capable CPU
DIMM Speed DPC
2133 DIMM
LRDIMM
(QR)
RDIMM
LRDIMM
(8R, DR, SR) (QR)
RDIMM
LRDIMM
(8R, DR, SR) (QR)
RDIMM (8R, DR, SR)
1DPC
1600
1600
1866
1866
2133
2133
2DPC
1600
1600
1866
1866
2133
2133
3DPC
1600
1600
1600
1600
1866
1866
(32 GB RDIMMs and
16 GB DIMMs)
1600
(64 GB TSV RDIMMs,
8 GB RDIMMs)
22
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
CONFIGURING the SERVER
Table 6 2400-MHz DIMM Memory Speeds with Different v4 CPUs
DIMM and CPU
Frequencies
LRDIMM
(QRx4) 64 GB1
RDIMM
(2Rx4) 32 GB
LRDIMM
(QRx4) 32 GB1
RDIMM
(SRx4) 16 GB
RDIMM
(SRx4) 8 GB
1.2 V
1.2 V
1.2 V
1.2 V
1.2 V
1DPC
2400 MHz
2400 MHz
2400 MHz
2400 MHz
2400 MHz
2DPC
2400 MHz
2400 MHz
2400 MHz
2400 MHz
2400 MHz
3DPC
2133 MHz
1866 MHz
2133 MHz
2133 MHz
2133 MHz
1DPC
2133 MHz
2133 MHz
2133 MHz
2133 MHz
2133 MHz
2DPC
2133 MHz
2133 MHz
2133 MHz
2133 MHz
2133 MHz
3DPC
1866 MHz
1866 MHz
1866 MHz
1866 MHz
1600 MHz
1DPC
1866 MHz
1866 MHz
1866 MHz
1866 MHz
1866 MHz
2DPC
1866 MHz
1866 MHz
1866 MHz
1866 MHz
1866 MHz
3DPC
1866 MHz
1600 MHz
1866 MHz
1600 MHz
1600 MHz
DPC
DIMM = 2400 MHz
CPU = 2400 MHz
DIMM = 2400 MHz
CPU = 2133 MHz
DIMM = 2400 MHz
CPU = 1866 MHz
Notes . . .
1. Available at a future date
■
■
The C220 M4 server supports four different memory reliability, availability, and
serviceability (RAS) modes:
—
Independent Channel Mode
—
Mirrored Channel Mode
—
Lockstep Channel Mode
Below are the system level RAS Mode combination limitations:
—
Mixing of Independent and Lockstep channel mode is not allowed per platform.
—
Mixing of Non-Mirrored and Mirrored mode is not allowed per platform.
—
Mixing of Lockstep and Mirrored mode is not allowed per platform.
■
Do not mix RDIMMs with LRDIMMs
■
Do not mix 64GB DDR4-2133-MHz TSV-RDIMMs with any other DIMMs
■
Single-rank DIMMs can be mixed with dual-rank DIMMs in the same channel
■
Do not mix quad-rank DIMMs with single- or dual-rank DIMMs in the same channel
■
For best performance, observe the following:
—
DIMMs with different timing parameters can be installed on different slots within the
same channel, but only timings that support the slowest DIMM will be applied to all.
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
23
CONFIGURING the SERVER
As a consequence, faster DIMMs will be operated at timings supported by the slowest
DIMM populated.
—
When one DIMM is used, it must be populated in DIMM slot 1 (farthest away from the
CPU) of a given channel.
—
When single, dual or quad rank DIMMs are populated for 2DPC or 3DPC, always
populate the higher number rank DIMM first (starting from the farthest slot). For a
3DPC example, first populate with quad-rank DIMMs in the DIMM slot 1. Then
dual-rank DIMMs in the DIMM 2 slot. Then single-rank DIMMs in the DIMM 3 slot.
■
DIMMs for CPU 1 and CPU 2 (when populated) must always be configured identically.
■
When using mirroring, DIMMs must be installed in identical pairs across paired DDR4 buses.
That is, mirrored pairs in channels A and B must be identical and pairs in channels C and D
must be identical. However, the DIMMs used in channels A and B can be different from those
in channels C and D.
■
Memory mirroring reduces the amount of available memory by 50% (quantity of DIMMs must
be even for mirroring).
■
Non-ECC DIMMs are not supported.
■
Cisco memory from previous generation servers (DDR3) is not compatible with this server
For more information regarding memory, see CPUs and DIMMs, page 68.
24
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
CONFIGURING the SERVER
STEP 4
SELECT RAID CONTROLLERS
RAID Controller Options (internal HDD/SSD support)
Embedded Software RAID
You can choose either the default embedded software RAID or the embedded software RAID 5
key upgrade.
■
The default RAID configuration is embedded software RAID, which supports SATA HDDs (RAID
0, 1, 10).
■
The embedded software RAID 5 key upgrade supports RAID 0, 1, 5, 10.
NOTE: The embedded software RAID in the Intel chipset hub is split into two, SATA
and sSATA (secondary SATA). They are seen as separate software RAID controllers and
are configurable separately. For more details, see Embedded SATA RAID: Two SATA
Controllers, page 76.
Cisco 12G SAS Modular RAID Controller
You can choose the Cisco 12G SAS RAID controller, which plugs into a dedicated RAID controller card slot.
This RAID controller supports RAID 0, 1, 10 (without the FBWC option) and supports up to RAID 0, 1, 10, 5, 6,
50, 60 (with the FBWC option).
NOTE: The number of RAID groups (virtual drives) supported per RAID controller is
as follows:
■
Embedded RAID = 8
■
Cisco 12G SAS Modular RAID controller = 64
SAS HBA (internal HDD/SSD/JBOD support)
Instead of a RAID controller, you can choose a SAS HBA for internal drive connectivity
(non-RAID):
■
Cisco 12 Gbps Modular SAS HBA, which plugs into a dedicated RAID controller slot.
SAS HBA (external JBOD support)
In addition to a RAID controller or JBOD controller for internal drives, you can choose the
following SAS HBA for external connectivity (non-RAID), which plugs into one of the PCIe slots:
■
Cisco 9300-8e 12G SAS HBA (provides 8 SAS ports for external JBOD connectivity).
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
25
CONFIGURING the SERVER
RAID Volumes and Groups
When creating each RAID volume, follow these guidelines:
■
Use the same capacity for each drive in each RAID volume
■
For embedded software RAID or the embedded software RAID 5 key upgrade:
■
—
Use only SATA HDDs
—
Embedded software RAID has two ports and each port can control 4 drives, for 8
drives total.
—
Each set of 4 SATA HDDs for a port must be in separate RAID volumes.
—
You cannot mix drives across ports to create a RAID volume.
—
For more details, see Embedded SATA RAID: Two SATA Controllers, page 76.
For the Cisco 12G SAS modular RAID controller upgrade:
—
Use either all SAS HDDs, all SAS SSDs, or all SATA SSDs in each RAID volume
The number of RAID groups (virtual drives) supported per RAID controller is as follows:
■
Embedded RAID = 8
■
Cisco 12G SAS Modular RAID controller = 64
Select Controller Options
Select one of the following:
■
Embedded software RAID (this is the default if no other selection is made), or
■
Embedded software RAID 5 key upgrade option for internal drives (see Table 7 on page 27),
or
■
One Cisco 12G SAS modular RAID controller or Cisco 12 Gbps Modular SAS HBA (see Table 8
on page 27), or
■
Mixed controllers:
—
One Cisco 12G SAS modular RAID controller or one Cisco 12 Gbps Modular SAS HBA
and
—
One or two Cisco 9300-8E 12G SAS HBAs for external SAS JBOD/enclosure
connectivity support (see Table 8 on page 27).
NOTE: Mixing the Cisco 9300-8e HBA in the same server as the Cisco 12 Gbps
Modular SAS HBA requires the following firmware levels:
26
■
Cisco IMC/BIOS 2.0(8) or later
■
Cisco UCS Manager 2.2(6) or later (for integrated servers only)
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
CONFIGURING the SERVER
■
Dual HBAs:
—
Two Cisco 9300-8E 12G SAS HBAs for external SAS JBOD/enclosure connectivity
support (see Table 8).
For the Cisco 12G SAS modular RAID controller, select an appropriate optional RAID configuration
listed in Table 8 on page 27
NOTE: The Cisco 12G SAS modular RAID controller can be ordered with or without an
optional FBWC (cache). The FBWC option backs up the RAID controller write cache.
The FBWC is available in 512 MB, 1 GB, 2 GB, or 4 GB sizes. See Table 8 on page 27
for details.
NOTE: For all valid combinations of embedded RAID and internal/external RAID
controller combinations, see RAID Details, page 74.
Table 7 shows the product ID for the C220 M4 server entry-level RAID solution. This RAID option is
accomplished with embedded software that supports a limited number of drives, operating systems, and
virtualized environments. For a more comprehensive enterprise RAID solution, choose the Cisco 12G SAS
modular RAID controller listed in Table 8.
Table 7 Entry Level Software RAID Solution
Product ID (PID)
PID Description
Embedded Software RAID 5 Key Upgrade
UCSC-SWRAID5
Embedded Software RAID 5 key upgrade, consisting of a storage controller unit
(SCU) module that plugs into a 2-pin header on the motherboard, supporting
up to eight internal SATA-only HDDs. See Embedded SATA RAID: Two SATA
Controllers, page 76. This module upgrades the default embedded software
RAID to add RAID 5. This option supports RAID 0, 1, 10, 5 and operates at 6
Gbps. Operating systems supported are Windows and Linux only (no VMware
support).
VMware ESX/ESXi or any other virtualized environments (such as Hyper-V, Xen,
or KVM) are not supported for use with the embedded software RAID
controller.
Table 8 Hardware Controller Options
Product ID (PID)
PID Description
Controllers for Internal Drives
Note that if the following Cisco 12G SAS Modular RAID controller or Cisco 12Gbps Modular SAS HBA
controller is selected, it is factory-installed in the dedicated internal slot.
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
27
CONFIGURING the SERVER
Table 8 Hardware Controller Options (continued)
Product ID (PID)
PID Description
UCSC-MRAID12G
Cisco 12G SAS Modular RAID Controller
UCSC-SAS12GHBA
■
Supports up to 24 internal SAS HDDs and SAS/SATA SSDs
(limited to 8 drives in this server)
■
Supports JBOD, RAID 0, 1, 10 (with no FBWC option chosen) and has the
ability to also support RAID 5, 6 if a Flash-Backed Write cache upgrade is
chosen (shown below in this table)
Cisco 12 Gbps Modular SAS HBA
■
Supports up to 24 internal SAS HDDs and SAS/SATA SSDs
(limited to 8 drives in this server)
■
Supports JBOD mode only (no RAID functionality. Ideal for SDS (Software
Defined Storage) applications. It is also ideal for environments demanding
the highest IOPs (for external SSD attach), where a RAID controller can be
an I/O bottleneck.
Flash-Backed Write Cache (FBWC) Upgrade Options for Cisco 12G SAS Modular RAID controller
UCSC-MRAID12G-512
512 MB FBWC, which includes a 512 MB memory plus a SuperCap for data cache
power backup for the Cisco 12G SAS Modular RAID controller. Supports JBOD,
RAID 0, 1, 5, and 50.
UCSC-MRAID12G-1GB
1 GB FBWC, which includes a 1 GB MB memory plus a SuperCap for write cache
backup. Supports JBOD, RAID 0, 1, 10, 5, 6, 50, and 60.
UCSC-MRAID12G-2GB
2 GB FBWC, which includes a 2 GB MB memory plus a SuperCap for write cache
backup. Supports JBOD, RAID 0, 1, 10, 5, 6, 50, and 60.
UCSC-MRAID12G-4GB
4 GB FBWC, which includes a 4 GB MB memory plus a SuperCap for write cache
backup. Supports JBOD, RAID 0, 1, 10, 5, 6, 50, and 60.
SAS HBA for External JBOD Attach
Two SFF8644 mini-SAS HD connectors on this card are accessible at the rear of the chassis.
UCSC-SAS9300-8E
Cisco 9300-8e 12G SAS HBA for external JBOD attach
■
Supports external JBOD using X8 wide SAS ports.
NOTE: For Cisco SAS 9300-8e 12G SAS HBA external drive enclosure
support, see the enclosure section of the compatibility list at the
following link:
http://tinyurl.com/pp83xyk
Customers should contact their storage vendor for technical support
related to external JBOD enclosures.
SuperCap Option
UCSC-MRAID-SC=
Spare SuperCap for Cisco 12G SAS Modular RAID, including all cables. This is a
spare SuperCap. It is the exact same SuperCap that ships with the FBWC
options listed earlier in this table and can be used as a replacement or upgrade
part.
RAID Configuration Options (not available for Cisco 12 Gbps Modular SAS HBA or embedded software
RAID)
28
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
CONFIGURING the SERVER
Table 8 Hardware Controller Options (continued)
Product ID (PID)
PID Description
R2XX-SRAID0
Enable Single Disk Raid 0 Setting
R2XX-RAID0
Factory preconfigured RAID striping option
Enable RAID 0 Setting. Requires a minimum of one hard drive.
R2XX-RAID1
Factory preconfigured RAID mirroring option
Enable RAID 1 Setting. Requires exactly two drives with the same size, speed,
capacity.
R2XX-RAID5
Factory preconfigured RAID option
Enable RAID 5 Setting. Requires a minimum of three drives of the same size,
speed, capacity.
R2XX-RAID6
Factory preconfigured RAID option
Enable RAID 6 Setting. Requires a minimum of four drives of the same size,
speed, capacity.
NOTE: Although RAID levels 50 and 60 are not orderable from the factory, they are
supported for selected controllers as shown in Table 8.
Approved Configurations
■
The embedded software RAID default supports up to 8 internal SATA HDDs with RAID 0, 1, 10
support.
■
The embedded software RAID 5 upgrade key option supports up to 8 internal SATA HDDs with
RAID 0, 1, 10, 5 support.
■
The Cisco 12G SAS Modular RAID controller upgrade option supports up to 8 internal drives
with up to RAID 0, 1, 10, 5, 6, 50, 60 support (with FBWC option chosen).
■
The Cisco 12 Gbps Modular SAS HBA upgrade option supports up to 8 internal drives with
JBOD support.
■
The Cisco 9300-8e 12G SAS HBA supports up to 8 external SAS ports with JBOD support.
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
29
CONFIGURING the SERVER
See Table 9 for a summary of the supported controller configuration options.
Table 9 Supported Controller Configurations for C220 M4 SFF Server
Embedded
# CPUs
RAID1
Cisco 12G SAS Modular RAID
Controller or
Cisco 12 Gbps Modular SAS
HBA2
(only one can be installed
at a time)
Cisco 12G SAS Cisco 12 Gbps
Modular RAID Modular SAS
Controller
HBA
1
1
1
1
Enabled
Not allowed
Not allowed
Enabled
Not allowed
Not allowed
Not
allowed
Installed in
dedicated
slot
Installed in
dedicated
slot
Not
allowed
Installed in
dedicated
slot
Installed in
dedicated
slot
Cisco
9300-8E
12G SAS
HBA3
Card
absent
Installed
slot 1
Card
absent
Installed
in slot 14
# Drives
Supported
RAID Support
Internal
Drive
Types
Allowed
8 internal
0, 1, 10 (default)
or
0, 1, 10, 5
(RAID 5 key
upgrade)
SATA HDDs
8 internal
1024
external
0, 1, 10 (default)
or
0, 1, 10, 5
(RAID 5 key
upgrade) for
internal drives, as
well as JBOD for
external drives
SATA HDDs
8 internal
0,1,10,5,6,50, 60
(for 12G SAS) or
JBOD
(for Modular SAS
HBA)
SAS HDDs,
SAS/SATA
SSDs
8 internal,
1024
external
0,1,10,5,6,50, 60
(for 12G SAS) or
JBOD
(for Modular SAS
HBA) as well as
JBOD for external
drives
SAS HDDs,
SAS/SATA
SSDs
8 internal
0, 1, 10 (default)
or
0, 1, 10, 5
(RAID 5 key
upgrade)
SATA HDDs
Only one of the above can be
installed at a time
2
30
Enabled
Not allowed
Not allowed
Card
absent
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
CONFIGURING the SERVER
Table 9 Supported Controller Configurations for C220 M4 SFF Server (continued)
Embedded
# CPUs
RAID1
Cisco 12G SAS Modular RAID
Controller or
Cisco 12 Gbps Modular SAS
HBA2
(only one can be installed
at a time)
Cisco 12G SAS Cisco 12 Gbps
Modular RAID Modular SAS
Controller
HBA
2
2
Enabled
Not allowed
Not allowed
Not
allowed
Installed in
dedicated
slot
Installed in
dedicated
slot
Cisco
9300-8E
12G SAS
HBA3
Installed
in any
slot
Card
absent
# Drives
Supported
RAID Support
Internal
Drive
Types
Allowed
8 internal
1024
external
0, 1, 10 (default)
or
0, 1, 10, 5
(RAID 5 key
upgrade) for
internal drives, as
well as JBOD for
external drives
SATA HDDs
8 internal
0,1,10,5,6,50,60
(for 12G SAS) or
JBOD
(for Modular SAS
HBA)
SAS HDDs,
SAS/SATA
SSDs
8 internal
1024
external
0,1,10,5,6,50,60
(for 12G SAS) or
JBOD
(for Modular SAS
HBA) as well as
JBOD for external
drives
SAS HDDs,
SAS/SATA
SSDs
Only one of the above can be
installed at a time
2
Not
allowed
Installed in
dedicated
slot
Installed in
dedicated
slot
Installed
in any
slot
Only one of the above can be
installed at a time
Notes . . .
1. The RAID configuration options listed in Table 8 on page 27 are not available if you have embedded software
RAID or choose the embedded software RAID 5 key upgrade (in this case, you must configure RAID yourself using
separate software).
2. If you want to boot from a device other than the Cisco 12G SAS Modular RAID controller or Cisco 12 Gbps Modular
SAS HBA, you can leave the card installed. Just disable the OPROM for its slot, and the system will boot even
with the card installed.
3. External drive PCIe controller card is the Cisco 9300-8e 12G SAS HBA and can be installed simultaneously with
the Cisco 12G SAS Modular RAID controller card or Cisco 12 Gbps Modular SAS HBA.
4. Only slot 1 is supported for 1-CPU systems.
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
31
CONFIGURING the SERVER
Caveats
■
A maximum of two Cisco 9300-8e 12G SAS HBAs can be installed, and they can be installed in
any slot (depending on the number of CPUs installed). The system can also support
combinations of one Cisco 9300-8e 12G SAS HBA and a Storage Accelerator card along with
either a Cisco 12G SAS Modular RAID Controller, or a Cisco 12 Gbps Modular SAS HBA.
■
For the Cisco 12G SAS Modular RAID controller, you can choose an optional RAID
configuration (up to RAID 0, 1, 10, 5, or 6 if optional FBWC option is chosen), which is
preconfigured at the factory. The RAID level you choose must be an available RAID choice for
the controller selected. RAID levels 50 and 60 are supported, although they are not available
as configuration options. It plugs into an internal RAID controller slot and can be combined
with one or two UCS 9300-8e 12G SAS HBAs.
■
A system supports up to 8 SATA-only HDDs through embedded software RAID if no Cisco 12G
SAS Modular RAID controller or Cisco 12 Gbps Modular SAS HBA is chosen.
NOTE: For more important information regarding RAID support, see RAID Details,
page 74 and RAID Option ROM (OPROM) Settings, page 75.
32
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
CONFIGURING the SERVER
STEP 5
SELECT HARD DISK DRIVES (HDDs) or SOLID STATE DRIVES (SSDs)
The standard disk drive features are:
■
2.5-inch small form factor
■
Hot-pluggable
■
Drives come mounted in sleds
Select Drives
The available drives are listed in Table 10.
Table 10 Available Hot-Pluggable Sled-Mounted HDDs and SSDs
PID Description1
Drive
Capacity
Type
UCS-HD600G15K9
600GB 12G SAS 15K RPM SFF HDD (SED)
SAS
600 GB
UCS-HD600G15K12G
600 GB 12G SAS 15K RPM SFF HDD
SAS
600 GB
UCS-HD450G15K12G
450 GB 12G SAS 15K RPM SFF HDD
SAS
450 GB
UCS-HD300G15K12G
300 GB 12G SAS 15K RPM SFF HDD
SAS
300 GB
UCS-HD18G10K9
1.8TB 12G SAS 10K RPM SFF HDD (4K format, SED)
SAS
1.8 TB
UCS-HD12G10K9
1.2 TB 12G SAS 10K RPM SFF HDD (SED)
SAS
1.2 TB
UCS-HD300G10K9
300GB 12G SAS 10K RPM SFF HDD (SED)
SAS
300 GB
UCS-HD18TB10KS4K2
1.8 TB 12 Gbps SAS 10K RPM SFF HDD (4K sector format)
SAS
1.8 TB
UCS-HD12TB10K12G
1.2 TB 12G SAS 10K RPM SFF HDD
SAS
1.2 TB
UCS-HD900G10K12G
900 GB 12G SAS 10K RPM SFF HDD
SAS
900 GB
UCS-HD600G10K12G
600 GB 12G SAS 10K RPM SFF HDD
SAS
600 GB
UCS-HD600G10KS4K1
600 GB 12 Gbps SAS 10K RPM SFF HDD (4K sector format)
SAS
600 GB
UCS-HD300G10K12G
300 GB 12G SAS 10K RPM SFF HDD
SAS
300 GB
UCS-HDD900GI2F106
900 GB 6 Gbps SAS 10K RPM SFF HDD
SAS
900 GB
A03-D600GA2
600 GB 6 Gbps SAS 10K RPM SFF HDD
SAS
600 GB
A03-D300GA2
300 GB 6 Gbps SAS 10K RPM SFF HDD
SAS
300 GB
Product ID (PID)
HDDs (15K RPM)
HDDs (10K RPM)
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
33
CONFIGURING the SERVER
Table 10 Available Hot-Pluggable Sled-Mounted HDDs and SSDs (continued)
PID Description1
Drive
Capacity
Type
UCS-HD2T7KS4K1
2 TB 12G SAS 7.2K RPM SFF HDD (4K sector format)
SAS
2 TB
UCS-HD2T7K12G
2 TB 12G SAS 7.2K RPM SFF HDD
SAS
2 TB
UCS-HDIT7KS4K1
1 TB 12G SAS 7.2K RPM SFF HDD (4K sector format)
SAS
1 TB
UCS-HD1T7K12GA
1 TB 12G SAS 7.2K RPM SFF HDD
SAS
1 TB
UCS-HD1T7K6GA
1 TB 6G SATA 7.2K RPM SFF HDD
SATA
1 TB
UCS-HD1T7KS2-E
1 TB 6 Gbps SAS 7.2K RPM SFF HDD
SAS
1 TB
SATA
1 TB
Product ID (PID)
HDDs (7.2K RPM)
A03-D1TBSATA
1 TB 6 Gbps SATA 7.2K RPM SFF
HDD3
SSDs
Enterprise Performance SSDs (High endurance, supports up to 10 FDWP (Full drive writes per day))4
UCS-SD16TBEK9
1.6 TB Enterprise performance SAS SSD (10XFWPD, SED)
SAS
1.6 TB
UCS-SD800GBEK9
800 GB Enterprise performance SAS SSD (10X FWPD, SED)
SAS
800 GB
UCS-SD600GBE3K9
600 GB Enterprise performance SATA SSD (3X FWPD, SED)
SATA
600 GB
UCS-SD400GBEK9
400 GB Enterprise performance SAS SSD (10X FWPD, SED)
SAS
400 GB
UCS-SD16TB12S4-EP
1.6 TB 2.5 inch Enterprise Performance 12G SAS SSD(10X endurance)
SAS
1.6 TB
UCS-SD16TB12S3-EP
1.6 TB 2.5 inch Enterprise Performance 6G SATA SSD(3X endurance)
SATA
1.6 TB
UCS-SD400G12S4-EP
400 GB 2.5 inch Enterprise Performance 12G SAS SSD (10X endurance)
SAS
400 GB
UCS-SD800G12S4-EP
800 GB 2.5 inch Enterprise Performance 12G SAS SSD (10X endurance)
SAS
800 GB
UCS-SD800G0KS2-EP
800 GB Enterprise Performance 6 Gbps SAS eMLC SSD (Samsung 1625)
SAS
800 GB
UCS-SD480G12S3-EP
480 GB 2.5 inch Enterprise Performance 6GSATA SSD (3X endurance)
SATA
480 GB
UCS-SD400G12S2-EP
400 GB Enterprise Performance 12 Gbps SAS eMLC SSD (Toshiba PM2)
SAS
400 GB
UCS-SD400G0KS2-EP
400 GB Enterprise Performance 6 Gbps SAS eMLC SSD (Samsung 1625)
SAS
400 GB
UCS-SD200G0KS2-EP
200 GB Enterprise Performance 6 Gbps SAS eMLC SSD (Samsung 1625)
SAS
200 GB
Enterprise Value SSDs (Low endurance, supports up to 1 FDWP (Full drive write per day))5
UCS-SD960GBE1K9
960GB Enterprise value SATA SSD (1X FWPD, SED)
SATA
960 GB
UCS-SD480GBE1K9
4480GB Enterprise Value SATA SSD (1XFWPD, SED)
SATA
480 GB
UCS-SD38TBKS4-EV
3.8TB 2.5 inch Enterprise Value 6G SATA SSD (Samsung 863)
SATA
3.8 TB
UCS-SD16TBKS4-EV
1.6 TB 2.5 inch Enterprise Value 6G SATA SSD (Intel 3510)
SATA
1.6 TB
UCS-SD480GBKS4-EV
480 GB 2.5 inch Enterprise Value 6G SATA SSD (Intel 3510)
SATA
480 GB
UCS-SD120GBKS4-EV
120 GB 2.5 inch Enterprise Value 6G SATA SSD (Intel 3510)
SATA
120 GB
UCS-SD960GBKS4-EV
960 GB 2.5 inch Enterprise Value 6G SATA SSD (Samsung PM863)
SATA
960 GB
UCS-SD240GBKS4-EV
240 GB 2.5 inch Enterprise Value 6G SATA SSD
SATA
240 GB
34
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
CONFIGURING the SERVER
Notes . . .
1. For all self-encrypting drives (SED), standalone Management (CIMC) is supported for configuring and managing
local keys (UCSM is not supported). Also, 4K format drives do not support Vmware and require UEFI boot.
2. Operating system support on 4k sector size drives is as follows:
- Windows: Win2012 and Win2012R2.
- Linux: RHEL 6.5/6.6/7.0/Sles 11 SP3 and Sles 12.
- ESXi/Vmware is not supported
EFI mode is available only for boot support- legacy boot mode is not supported. EFI mode is needed only when
you boot from 4K format drives.
Ensure that the 4K sector size and 512 byte sector size drives are not configured as part of the same RAID
volume.
3. This drive is supported only with embedded RAID.
4. Targeted for write centric IO applications. Supports endurance of 10 FDWP (Full drive writes per day). Target
applications are caching, online transaction processing (OLTP), data warehousing, and virtual desktop
infrastructure (VDI).
5. Targeted for read centric IO applications. Supports endurance of 1 FDWP (Full drive write per day). Target
applications are boot, streaming media, and collaboration.
The available plug-in PCIe SSD drives and kit are listed in Table 11.
Table 11 Available Plug-In NVMe PCIe SSDs1
Product ID (PID)
PID Description
Drive Type
Capacity
NVMe PCIe SSDs
UCS-SDHPCIE16TB
1.6 TB 2.5-inch NVMe-based PCIe SSD (WDHGST)
NVMe SSD
1.6 TB
UCS-SDHPCIE800GB
800 GB 2.5-inch NVMe-based PCIe SSD (WDHGST)
NVMe SSD
800 GB
C220 M4 NVMe PCIe SSD riser card kit and cables2
UCSC-PCI-2B-220M4
Notes . . .
1. If you choose one or two PCIe SSD drives, drive slots 1 and 2 at the front of the chassis are reserved for these
drives (see Figure 2 on page 6 for drive slot numbering).
2. You must order a riser card kit and cables if you order an NVMe PCIe SSD. One riser card kit and
cables supports up to two NVMe PCIe SSDs.
Approved Configurations
(1) Embedded Software RAID or Embedded Software RAID 5 Key Upgrade
■
Select up to eight SATA-only HDDs from Table 10 on page 33.
(2) Cisco 12G SAS Modular RAID Controller
■
If you selected a Cisco 12G SAS Modular RAID controller you have the following options:
—
Cisco 12G SAS Modular RAID controller with no FBWC option (supports JBOD, RAID 0,
1, 10)
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
35
CONFIGURING the SERVER
—
Cisco 12G SAS Modular RAID controller with FBWC option (supports JBOD and up to
RAID 0, 1, 10, 5, 6, 50, and 60)
—
For either option, select up to eight SAS HDDs, eight SAS SSDs, or eight SATA SSDs
listed in Table 10. The Cisco 12G SAS Modular RAID controller does not support SATA
HDDs.
(3) Cisco 12 Gbps Modular SAS HBA
■
If you selected a Cisco 12 Gbps Modular SAS HBA, select up to eight SAS HDDs or eight
SAS/SATA SSDs.
See SELECT RAID CONTROLLERS, page 25 for more details.
(4) Systems Using Plug-in NVMe PCIe SSDs
Systems using NVMe PCIe SSDs are controlled through the PCIe bus. If you choose one or two
NVMe PCIe SSDs, they must be plugged into only drive slots 1 and 2 in the front of the chassis.
Additionally, any system implementing NVMe PCIe SSDs must be ordered with two CPUs.
Caveats
36
■
You can choose only SATA HDDs when using embedded software RAID.
■
You can choose only SAS HDDs or SAS/SATA SSDs when using the Cisco 12G SAS Modular RAID
Controlleror Cisco 12 Gbps Modular SAS HBA.
■
You can mix HDDs and SSDs as long as you keep all HDDs in their own RAID volume and all
SSDs in their own RAID volume.
■
You can mix SAS HDDs and SAS/SATA SSDs when using the Cisco 12G SAS Modular RAID
Controller or Cisco 12 Gbps Modular SAS HBA.
■
If you order any NVMe PCIe SSDs, you must also order two CPUs.
■
A maximum of two NVMe PCIe SSDs can be ordered.
■
NVMe PCIe SSDs are not bootable
■
NVMe PCIe SSDs cannot be controlled with a RAID controller.
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
CONFIGURING the SERVER
STEP 6
SELECT PCIe OPTION CARD(s)
The standard PCie card offerings are:
■
Modular LAN on Motherboard (mLOM)
■
Virtual Interface Cards (VICs)
■
Network Interface Cards (NICs)
■
Converged Network Adapters (CNAs)
■
Host Bus Adapters (HBAs)
■
UCS Storage Accelerators
Select PCIe Option Cards
The available PCIe option cards are listed in Table 12.
Table 12 Available PCIe Option Cards
Product ID (PID)
PID Description
Card
Height
Modular LAN on Motherboard (mLOM)1
UCSC-MLOM-C10T-02
Cisco UCS VIC1227T VIC MLOM - Dual Port 10GBaseT
N/A
UCSC-MLOM-CSC-02
Cisco UCS VIC1227 VIC MLOM - Dual Port 10Gb SFP+
N/A
UCSC-MLOM-IRJ45
Intel i350 quad-port MLOM NIC
N/A
UCSC-MLOM-C40Q-03
Cisco VIC 1387 Dual Port 40Gb QSFP CNA MLOM
N/A
Virtual Interface Cards (VICs)
UCSC-PCIE-CSC-02
Cisco VIC 1225 Dual Port 10Gb SFP+ CNA
Half
UCSC-PCIE-C10T-02
Cisco VIC 1225T Dual Port 10GBaseT CNA
Half
UCSC-PCIE-C40Q-03
Cisco VIC 1385 Dual Port 40Gb QSFP+ CNA w/RDMA
Half
Network Interface Cards (NICs)
1 Gb NICs
N2XX-ABPCI03-M3
Broadcom 5709 Quad Port 1Gb w/TOE iSCSI for M3 Servers
Half
N2XX-ABPCI01-M3
Broadcom 5709 Dual-Port Ethernet PCIe Adapter M3 & later
Half
UCSC-PCIE-IRJ45
Intel i350 Quad Port 1Gb Adapter
Half
N2XX-AIPCI01
Intel X520 Dual Port 10Gb SFP+ Adapter
Half
UCSC-PCIE-ITG
Intel X540 Dual Port 10GBase-T Adapter
Half
UCSC-PCIE-QNICBT
QLogic QLE8442 dual-port 10Gbase-T NIC
Half
UCSC-PCIE-QNICSFP
QLogic QLE8442 dual-port 10G SFP+ NIC
Half
10 Gb NICs
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
37
CONFIGURING the SERVER
Table 12 Available PCIe Option Cards (continued)
Product ID (PID)
PID Description
Card
Height
10 Gb Converged Network Adapters (CNAs)
UCSC-PCIE-E14102B
Emulex OCe14102B-UX dual-port 10G SFP+ with iSCSI, FCoE CNA
Half
UCSC-PCIE-E14102
Emulex OCe14102-UX dual-port 10 GbE FCoE CNA
Half
UCSC-PCIE-Q8362
Qlogic QLE8362 dual-port 10 GbE FCoE CNA
Half
Host Bus Adapters (HBAs)
N2XX-AQPCI05
Qlogic QLE2562 Dual Port 8Gb Fibre Channel HBA
Half
UCSC-PCIE-Q2672
Qlogic QLE2672-CSC, 16Gb Fibre Channel HBA with SR Optics
Half
N2XX-AEPCI05
Emulex LPe 12002 Dual Port 8Gb Fibre Channel HBA
Half
UCSC-PCIE-E16002
Emulex LPe16002-M6, 16Gb Fibre Channel HBA with SR Optics
Half
UCS Storage
Accelerators2
UCSC-F-S13002
UCS Rack PCIe Storage 1300 GB SanDisk SX350 Medium Endurance
Half
UCSC-F-S16002
UCS Rack PCIe Storage 1600 GB SanDisk SX350 Medium Endurance
Half
UCSC-F-S32002
UCS Rack PCIe Storage 3200 GB SanDisk SX350 Medium Endurance
Half
UCSC-F-S64002
UCS Rack PCIe Storage 6400 GB SanDisk SX350 Medium Endurance
Full
UCSC-F-FIO-1000PS
UCS 1000GB Fusion ioMemory3 PX Performance line for C-Series
Half
UCSC-F-FIO-1300PS
UCS 1300GB Fusion ioMemory3 PX Performance line for C-Series
Half
UCSC-F-FIO-2600PS
UCS 2600GB Fusion ioMemory3 PX Performance line for C-Series
Half
UCSC-F-FIO-5200PS
UCS 5200GB Fusion ioMemory3 PX Performance line for C-Series
Full
UCSC-F-FIO-3200SS
UCS 3200GB Fusion ioMemory3 SX Scale line for C-Series
Half
UCSC-F-FIO-6400SS
UCS 6400 GB Fusion ioMemory3 SX Scale line for C-Series
Full
Notes . . .
1. The mLOM cards do not plug into any of the riser 1 or riser 2 card slots; instead, they plug into a connector
inside the server chassis.
2. A maximum of two storage accelerator cards are supported if they are half height; the supported number of
full height cards is one.
Approved Configurations
(1) 1-CPU Systems
■
You can select up to one PCie option card (slot 1 for 1-CPU systems) listed in Table 12.
(2) 2-CPU Systems
■
38
You can select up to two PCie option cards (slots 1 and 2 for 2-CPU systems) listed in
Table 12.
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
CONFIGURING the SERVER
Caveats
■
A maximum of two storage accelerator cards are supported if they are half height; the
supported number of full-height cards is one.
■
For 1-CPU systems:
■
■
■
—
Only the full-height PCIe slot on riser 1 (slot 1) is supported
—
Only a single plug-in PCIe VIC card is supported and must be installed in slot 1 (the
full-height slot). However, in addition to the one PCIe VIC card, you can also choose
to install an mLOM VIC card.
—
If any of the Storage Accelerator cards are installed, they can be installed only in
slot 1.
For 2-CPU systems:
—
Both PCIe slots (slots 1 and 2) are supported
—
Two plug-in PCIe VIC cards can be installed in 2-CPU systems, using slots 1 and 2. In
addition, you can order an mLOM VIC card, which is installed in the mLOM slot inside
the chassis and thus have three VIC cards in operation at the same time. See
Table 12 on page 37 for the selection of plug-in and mLOM VIC cards. See also
Table 1 on page 8.
—
If any of the Storage Accelerator cards are installed, they can be installed only in
slot 1.
Other considerations for the Cisco VIC 1225/1225T/1227/1227T/1385 cards:
—
VIC 1225 and VIC 1227/1227T support 10G SFP+ optical and copper twinax
connections
—
VIC 1225T Supports RJ45 Category 6 or better twisted pair cable connections
—
VIC 1385 supports a 4x10 Gbps QSFP to SFP breakout fiber cable.
—
The 2-CPU version of the server supports installation of two PCIe Cisco VIC
1225/1225T/1385 card and they are supported in PCIe slots 1 and 2. Slot 1 is the
primary slot for UCSM integration and for Cisco card NIC mode.
—
The server supports up to two PCIe Cisco VICs (1225, 1225T, 1385) plus an MLOM VIC
(1227, 1227T), however, single wire management is supported on only one VIC at a
time. If multiple VICs are installed on a server, only one slot has NCSI enabled at a
time and for single wire management, priority goes to the MLOM slot, then slot 1,
then slot 2 for NCSI management traffic. When multiple cards are installed, connect
the single wire management cables in the priority order mentioned above.
—
Installation of the Cisco UCS VIC1225 requires that the server has CIMC firmware
version 1.4(6) or later installed and VIC firmware of 2.1(0) or later. Installation of
the Cisco UCS VIC1225T requires that the server has CIMC firmware version 1.5(1) or
later installed and VIC firmware of 2.1(1) or later.
—
The VIC features mentioned in this section are supported with the following
software releases: 2.0.6 (CIMC) and 2.2.5a (UCSM).
To help ensure that your operating system is compatible with the card you have selected, or
to see additional cards that have been qualified to work with the UCS C220 M4 server, but
are not sold on the Cisco pricelist, check the Hardware Compatibility List at this URL:
http://www.cisco.com/en/US/products/ps10477/prod_technical_reference_list.html
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
39
CONFIGURING the SERVER
STEP 7
ORDER OPTIONAL NETWORK CARD ACCESSORIES
Copper twinax cables and SFP optical modules may be ordered to support the two-port network cards that
are available with the server.
Choose Optional Twinax Cables
Table 13 lists the copper twinax cables available for the PCIe cards. You can choose cable
lengths of 1, 3, 5, 7, or 10 meters. The two longer cables (7 and 10 meters) are active, which
means that they contain active components within the SFP+ housing to improve signal quality.
Table 13 Available Twinax Cables
Product ID (PID)
PID Description
SFP-H10GB-CU1M
10GBASE-CU SFP+ Cable (1 M)
SFP-H10GB-CU3M
10GBASE-CU SFP+ Cable (3 M)
SFP-H10GB-CU5M
10GBASE-CU SFP+ Cable (5 M)
SFP-H10GB-ACU7M
10GBASE-CU SFP+ Cable (7 M)
SFP-H10GB-ACU10M
10GBASE-CU SFP+ Cable (10 M)
Approved Configurations
(1) Choose Up to Two Twinax Cables for Each Network Card Ordered
■
You may choose one or two twinax cables for each compatible PCIe network card ordered.
The cables can be different lengths; however, you would normally order two cables of equal
lengths to connect to the primary and redundant network switching equipment.
Choose Optional SFP Modules
Optical Cisco SFP+ modules are listed in Table 14.
Table 14 Available SFP Modules
Product ID (PID)
PID Description
SFP-10G-SR
10GBASE-SR SFP+ Module
850 nm, multimode, SR, 3.3V, LC connector, with Digital Optical Monitoring
SFP-10G-LR
10GBASE-LR SFP+ Module
1310 nm, single mode, LR, 3.3 V, with Digital Optical Monitoring
DS-SFP-FC8G-SW
8 Gbit SFP+ Module
850 nm, multimode, SR, 3.3V, LC connector, with Digital Optical Monitoring
40
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
CONFIGURING the SERVER
Approved Configurations
(1) Choose Up to Two SFP+ Modules for Each Network Card Ordered
■
You may choose one or two SFP+ optical modules cables for each compatible PCIe network
card ordered. You would normally order two modules for connecting to the primary and
redundant network switching equipment. With the SFP+ optical modules, you can use
common fiber optic cables, widely available.
See the Figure 5 on page 44 for typical SFP+ and twinax connections to the network cards.
Caveats
Check the table on the following page for compatibility between the PCIe network cards and
SFPs or twinax cables.
NOTE: The table shows all PCIe network cards for all C-series servers. Not all of
the cards shown in the table are supported in this server. The intent of the table
is to show compatibility between cards and twinax cables or SFPs.
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
41
CONFIGURING the SERVER
Table 15 PCIe Card Compatibility
Cisco SFP Modules
Twinax
Cables SFP-10G-SR SFP-10G-LR DS-SFP-FC8G-SW
PCIe Cards
Converged Network Adapters (CNAs)
UCSC-PCIE-BSFP
(Broadcom 57712 Dual Port 10Gb SFP+ w/TOE
iSCSI)
UCSC-PCIE-CSC-02
(Cisco VIC 1225 Dual Port 10Gb SFP+ CNA)
UCSC-PCIE-C10T-02
(Cisco VIC 1225T Dual Port 10GBaseT CNA)
UCSC-MLOM-CSC-02
(Cisco UCS VIC1227 VIC MLOM - Dual Port 10Gb
SFP+)
UCSC-MLOM-C10T-02
(Cisco UCS VIC1227T VIC MLOM - Dual Port
10GBaseT)
UCSC-PCIE-C40Q-02
(Cisco VIC 1285 Dual Port 40Gb QSFP CNA)
UCSC-PCIE-C40Q-03
(Cisco VIC 1385 Dual Port 40Gb QSFP+ CNA
w/RDMA)
UCSC-PCIE-ESFP
(Emulex OCe11102-FX dual-port 10 GbE FCoE CNA
(Gen 3 CNA))
UCSC-PCIE-QSFP
(QLogic QLE8242-CU dual-port 10 GbE FCoE CNA)
UCSC-PCIE-B3SFP
(Broadcom 57810 10Gb A-FEX SFP+
UCSC-PCIE-Q8362
(Qlogic QLE8362 dual-port 10 GbE FCoE CNA)
UCSC-PCIE-E14102
(Emulex OCe14102-UX dual-port 10 GbE FCoE
CNA)
Network Interface Cards (NICs)
N2XX-ABPCI01-M3
(Broadcom 5709 Dual-Port Ethernet PCIe Adapter
for M3 Servers)
N2XX-ABPCI03-M3
(Broadcom 5709 Quad Port 10/100/1Gb NIC
w/TOE iSCSI for M3 Servers
N2XX-AIPCI01
(Intel X520 Dual Port 10Gb SFP+ Adapter)
UCSC-PCIE-ITG
(Intel X540 Dual Port 10GBase-T Adapter)
UCSC-PCIE-IRJ45
(Intel i350 Quad Port 1Gb Adapter
42
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
Yes
Yes
Yes
No
No
No
No
No
Yes
No1
No
Yes
No1
No
Yes
Yes
No
Yes
Yes
Use Qlogic SFP
Yes
Yes
Yes
No
No
Use Qlogic SFP
Yes
No
Use RJ45 Ethernet cable
Use RJ45 Ethernet cable
Yes
Use Intel SFP
CDE2-SFP-1WLR or CDE2-SFP-1WSR
Use RJ45 Ethernet cable
Use RJ45 Ethernet cable
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
CONFIGURING the SERVER
Table 15 PCIe Card Compatibility (continued)
PCIe Cards
UCSC-PCIE-BTG
(Broadcom 57712 Dual Port 10GBASE-T w/TOE
iSCSI)
Host Bus Adapters (HBAs)
N2XX-AEPCI03
(Emulex LPe 11002 Dual Port 4Gb Fibre Channel
HBA
N2XX-AEPCI05
(Emulex LPe 12002 Dual Port 8Gb Fibre Channel
HBA)
N2XX-AQPCI03
(QLogic QLE2462 Dual Port 4Gb Fibre Channel
HBA)
N2XX-AQPCI05
(QLogic QLE2562 Dual Port 8Gb Fibre Channel
HBA)
UCSC-PCIE-Q2672
(Qlogic QLE2672-CSC, 16Gb Fibre Channel HBA
with SR Optics)
UCSC-PCIE-E16002
(Emulex LPe16002-M6, 16Gb Fibre Channel HBA
with SR Optics)
Cisco SFP Modules
Twinax
Cables SFP-10G-SR SFP-10G-LR DS-SFP-FC8G-SW
Yes
No
No
No
Preinstalled - do not change SFP
No
Preinstalled - do not change SFP
No
Preinstalled - do not change SFP
No
Preinstalled - do not change SFP
No
Preinstalled - do not change SFP
No
Preinstalled - do not change SFP
Notes . . .
1. This card supports a 4x10 Gbps QSFP to SFP breakout fiber cable.
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
43
CONFIGURING the SERVER
Figure 5
44
Network Card Connections
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
CONFIGURING the SERVER
STEP 8
ORDER POWER SUPPLY
The C220 M4 SFF server accommodates two power supplies. A lightly loaded server can operate
from one 770 W AC power supply or one 1050 W DC power supply. A fully loaded server might
need to be powered with two power supplies (see Table 16).
Use the power calculator at the following link to determine the needed power based on the
options chosen (CPUs, drives, memory, and so on):
http://ucspowercalc.cisco.com
Table 16
Power Supply PIDs
Product ID (PID)
PID Description
UCSC-PSU1-770W
770 W power supply
UCSC-PSUV2-1050DC
1050W V2 -48 VDC Power Supply for C220 M4 C-Series Server
NOTE: In a two power supply server, both power supplies must be identical.
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
45
CONFIGURING the SERVER
STEP 9
SELECT AC POWER CORD(s)
Using Table 17, select the appropriate AC power cords. You can select a minimum of no power
cords and a maximum of two. If you select the option R2XX-DMYMPWRCORD, no power cord is
shipped with the server.
Table 17 Available Power Cords
Product ID (PID)
PID Description
Images
R2XX-DMYMPWRCORD
No power cord (dummy PID to
allow for a no power cord option)
Not applicable
CAB-N5K6A-NA
Power Cord, 200/240V 6A, North
America
Cordset rating: 10 A, 250 V
Length: 8.2 ft
Connector:
IEC60320/C13
CAB-AC-L620-C13
AC Power Cord, NEMA L6-20 - C13,
2M/6.5ft
CAB-C13-CBN
CABASY,WIRE,JUMPER CORD, 27" L,
C13/C14, 10A/250V
CAB-C13-C14-2M
CABASY,WIRE,JUMPER CORD, PWR,
2 Meter, C13/C14,10A/250V
CAB-C13-C14-AC
CORD,PWR,JMP,IEC60320/C14,IEC6
0320/C13, 3.0M
46
186570
Plug: NEMA 6-15P
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
CONFIGURING the SERVER
Table 17 Available Power Cords
Product ID (PID)
PID Description
CAB-250V-10A-AR
Power Cord, 250V, 10A, Argentina
Images
2500 mm
Cordset rating: 10 A, 250/500 V MAX
Length: 8.2 ft
Plug:
EL 219
(IRAM 2073)
CAB-9K10A-AU
186571
Connector:
EL 701
(IEC60320/C13)
Power Cord, 250VAC 10A 3112 Plug,
Australia
Connector:
EL 701C
(EN 60320/C15)
Plug:
EL 210
(BS 1363A) 13 AMP fuse
Power Cord, SFS, 250V, 10A, China
Cordset rating 10A, 250V
(2500 mm)
Connector:
EL 701
(IEC60320/C13)
CAB-250V-10A-CN
AC Power Cord - 250V, 10A - PRC
CAB-9K10A-EU
Power Cord, 250VAC 10A CEE 7/7
Plug, EU
Plug:
M2511
Cordset rating: 10A/16 A, 250 V
Length: 8 ft 2 in. (2.5 m)
Connector:
VSCC15
SFS-250V-10A-ID
186573
Plug:
EL 218
(CCEE GB2009)
186576
SFS-250V-10A-CN
186580
Cordset rating: 10 A, 250 V/500 V MAX
Length: 2500mm
Power Cord, SFS, 250V, 10A, India
OVE
Plug:
EL 208
Cordset rating 16A, 250V
(2500mm)
187490
Connector:
EL 701
SFS-250V-10A-IS
Power Cord, SFS, 250V, 10A, Israel
EL-212
16A
250V
Cordset rating 10A, 250V/500V MAX
(2500 mm)
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
Connector:
EL 701B
(IEC60320/C13)
186574
Plug:
EL 212
(SI-32)
47
CONFIGURING the SERVER
Table 17 Available Power Cords
Product ID (PID)
PID Description
CAB-9K10A-IT
Power Cord, 250VAC 10A CEI
23-16/VII Plug, Italy
Images
Cordset rating: 10 A, 250 V
Length: 8 ft 2 in. (2.5 m)
Connector
C15M
(EN60320/C15 )
186575
Plug:
I/3G
(CEI 23-16)
CAB-9K10A-SW
Power Cord, 250VAC 10A MP232
Plug, Switzerland
Cordset rating: 10 A, 250 V
Length: 8 ft. 2 in (2.5 m)
Connector:
IEC 60320 C15
186578
Plug:
MP232-R
CAB-9K10A-UK
Power Cord, 250VAC 10A BS1363
Plug (13 A fuse), UK
Connector:
EL 701C
(EN 60320/C15)
Plug:
EL 210
(BS 1363A) 13 AMP fuse
CAB-9K12A-NA
Power Cord, 125VAC 13A NEMA
5-15 Plug, North America
CAB-250V-10A-BR
Power Cord - 250V, 10A - Brazil
1
186580
Cordset rating: 10 A, 250 V/500 V MAX
Length: 2500mm
76.2 From Plug End
2,133.6 ± 25
CAB-C19-C20-3M-JP
Power Cord C19-C20, 3M/10ft
Japan PSE mark
Image not available
CAB-48DC-40A-8AWG
Power Cord for -48VDC PSU, 3.5M,
3 Wire, 8AWG, 4
Image not available
CAB-JPN-3PIN
Power Cord 3PIN, Japan
Image not available
48
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
CONFIGURING the SERVER
STEP 10 ORDER TOOL-LESS RAIL KIT AND OPTIONAL REVERSIBLE CABLE
MANAGEMENT ARM
Select a Tool-Less Rail Kit
Select a tool-less rail kit from Table 18.
Table 18
Tool-Less Rail Kit Options
Product ID (PID)
PID Description
UCSC-RAILF-M4
Friction Rail Kit for C220 M4 Servers
UCSC-RAILB-M4
Ball Bearing Rail Kit for C220 M4 and C240 M4 Rack Servers
Select an Optional Reversible Cable Management Arm
The reversible cable management arm mounts on either the right or left slide rails at the rear of
the server and is used for cable management. Use Table 19 to order a cable management arm.
Table 19
Cable Management Arm
Product ID (PID)
PID Description
UCSC-CMAF-M4
Reversible CMA for C220 M4 tool-less friction and ball bearing rail kit
For more information about the tool-less rail kit and cable management arm, see the Cisco UCS
C220 M4 Installation and Service Guide at this URL:
http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c/hw/C220M4/install/C220M4.html
NOTE: If you plan to rackmount your UCS C220 M4 server, you must order one of the
tool-less rail kits.
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
49
CONFIGURING the SERVER
STEP 11 SELECT NIC MODE (OPTIONAL)
By default, the C220 M4 server NIC mode is configured to be Shared LOM Extended. This NIC
mode allows any LOM port or adapter card port to be used to access the Cisco Integrated
Management Controller (CIMC). The Cisco VIC card must be installed in a slot with NCSI support.
To change the default NIC mode to Dedicated, select the UCSC-DLOM-01 PID shown in Table 20.
In Dedicated NIC mode, the CIMC can be accessed only through the dedicated management port.
See Chassis Rear View, page 7 for the location of the management port.
To change the default NIC mode to Cisco Card Mode, select the UCSC-CCARD-01 PID shown in
Table 20. In this mode, you can assign an IP address to the CIMC using DHCP and from there you
can fully automate your deployment.
For more details on all the NIC mode settings, see
http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c/sw/gui/config/guide/2-0/b_
Cisco_UCS_C-series_GUI_Configuration_Guide_201.pdf
Table 20
50
Dedicated NIC Mode Ordering Information
Product ID (PID)
PID Description
UCSC-DLOM-01
Dedicated Mode BIOS setting for C-Series Servers
UCSC-CCARD-01
Cisco Card Mode BIOS setting for C-Series Servers
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
CONFIGURING the SERVER
STEP 12 ORDER A TRUSTED PLATFORM MODULE (OPTIONAL)
Trusted Platform Module (TPM) is a computer chip (microcontroller) that can securely store
artifacts used to authenticate the platform (server). These artifacts can include passwords,
certificates, or encryption keys. A TPM can also be used to store platform measurements that
help ensure that the platform remains trustworthy. Authentication (ensuring that the platform
can prove that it is what it claims to be) and attestation (a process helping to prove that a
platform is trustworthy and has not been breached) are necessary steps to ensure safer
computing in all environments.
The TPM ordering information is listed in Table 21.
Table 21
Trusted Platform Module
Product ID (PID)
PID Description
UCSX-TPM2-001
Trusted Platform Module 1.2 SPI-based for UCS Servers
UCSX-TPM2-002
Trusted Platform Module 2.0 for UCS servers
NOTE: The module used in this system conforms to TPM v1.2 and 2.0, as defined by
the Trusted Computing Group (TCG). It is also SPI-based.
NOTE: TPM installation is supported after-factory. However, a TPM installs with a
one-way screw and cannot be replaced, upgraded, or moved to another server. If a
server with a TPM is returned, the replacement server must be ordered with a new
TPM. If there is no existing TPM in the server, you can install TPM 2.0. You must first
upgrade to UCS firmware that supports Intel E5-2600 v4 CPUs, which is Cisco UCS
Manager Release 2.2(7) and later or Release 3.1(1) and later (because Cisco aligned
support for TPM 2.0 with these CPUs).
CAUTION: If the Cisco UCS server (with Intel E5-2600 v4 or v3 CPUs) is running UCS
firmware that added support for Intel E5-2600 v4 CPUs, then it will work with TPM
version 2.0. However, if you downgrade the firmware and BIOS to a version earlier
than Release 2.2(7) or earlier than Release 3.1(1), then you are vulnerable to a
potential security exposure. See the following support matrix for TPM versions.
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
51
CONFIGURING the SERVER
.
Table 22
TPM Support Matrix by Intel CPU Version
Intel CPU
TPM Version
Minimum UCS Manager (UCSM) Version
Intel E5-2600 v3
TPM 1.2
Release 2.2(3)
TPM 2.0
Release 2.2(7) or Release 3.1(1)
TPM 1.2
Release 2.2(7) or Release 3.1(1)
TPM 2.0
Release 2.2(7) or Release 3.1(1)
Intel E5-2600 v4
52
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
CONFIGURING the SERVER
STEP 13 ORDER CISCO FLEXIBLE FLASH SD CARD MODULE (OPTIONAL)
You can order 64 GB SD cards or 32 GB SD cards. See Figure 6 on page 66 for the location of the
SD cards. There are two locations, SD1 and SD2.
Table 23
64 GB Secure Digital (SD) Card (blank)
Product ID (PID)
PID Description
UCS-SD-64G-S
64 GB SD Card for UCS Servers
Table 24
32 GB Secure Digital (SD) Card (blank)
Product ID (PID)
PID Description
UCS-SD-32G-S
32 GB SD Card for UCS Servers
Caveats
■
Install either one or two 64 GB SD cards or one or two 32 GB SD cards
■
Do not mix SD card sizes
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
53
CONFIGURING the SERVER
STEP 14 ORDER OPTIONAL USB 3.0 DRIVE
You can order one optional USB 3.0 drive. The USB drive ordering information is listed in
Table 25.
Table 25
USB 3.0 Drive
Product ID (PID)
PID Description
UCS-USBFLSHB-16GB
UCS Servers 16 GB Flash USB Drive
See Figure 6 on page 66 for the location of the USB connector
54
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
CONFIGURING the SERVER
STEP 15 SELECT OPERATING SYSTEM AND VALUE-ADDED SOFTWARE
Several software programs are available. Select as desired from Table 1.
Table 26 Software (for 2-CPU servers)
PID Description
Product ID (PID)
Cisco One
C1F2PUCSK9
Cisco ONE Foundation Perpetual UCS
C1A1PUCSK9
Cisco ONE Enterprise Cloud Perpetual UCS
C1UCS-OPT-OUT
Cisco One Data Center Compute Opt Out Option Energy Management (JouleX)
CEM-DC-ENERGY
Cisco Energy Management (JouleX) DataCenter License 1 Device
UCS Director
CUIC-PHY-SERV-BM-U
Cisco UCS Director Resource Lic - 1 Phy Sevr node bare metal
CUIC-PHY-SERV-U
Cisco UCS Director Resource Lic - One physical Server node
CUIC-TERM
Acceptance of Cisco UCS Director License Terms
UCS Performance Manager
UCS-PM-IE
UCS Performance Manager
UCS-PM-EE
UCS Performance Manager Express
EVAL-UCS-PM-IE
UCS Performance Manager - 90 days evaluation
EVAL-UCS-PM-EE
UCS Performance Manager Express - 90 days evaluation
Nexus 1000V for Hyper-V and vSphere
N1K-VSG-UCS-BUN
Nexus 1000V Adv Edition for vSphere Paper License Qty 1
IMC Supervisor
CIMC-SUP-B10
IMC Supervisor- Branch Mgt SW for C & E-Series up to 1K Svrs
CIMC-SUP-B02
IMC Supervisor- Branch Mgt SW for C & E-Series up to 250 Svrs
UCS Multi-Domain Manager
UCS-MDMGR-100S
UCS Multi-Domain Manager (Central) Per Server License (100+)
UCS-MDMGR-50S
UCS Multi-Domain Manager (Central) Per Server License (50+)
UCS-MDMGR-1S
UCS Multi-Domain Manager (Central) Per Server License
UCS-MDMGR-10S
UCS Multi-Domain Manager (Central) Per Server License (10+)
UCS-MDMGR-1DMN
UCS Multi-Domain Manager (Central) Per Domain License
VMware vCenter
VMW-VCS-STD-1A
VMware vCenter 6 Server Standard, 1 yr support required
VMW-VCS-STD-3A
VMware vCenter 6 Server Standard, 3 yr support required
VMW-VCS-STD-5A
VMware vCenter 6 Server Standard, 5 yr support required
VMW-VCS-FND-1A
VMware vCenter 6 Server Foundation (3 Host), 1 yr supp reqd
VMW-VCS-FND-3A
VMware vCenter 6 Server Foundation (3 Host), 3 yr supp reqd
VMW-VCS-FND-5A
VMware vCenter 6 Server Foundation (3 Host), 5 yr supp reqd
Microsoft Windows Server
MSWS-12R2-DC2S
Windows Server 2012 R2 Datacenter (2 CPU/Unlimited VMs)
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
55
CONFIGURING the SERVER
Table 26 Software (for 2-CPU servers) (continued)
PID Description
Product ID (PID)
MSWS-12-ST2S
MSWS-12-DC2S
MSWS-12-ST2S-NS
MSWS-12R2-DC2S-NS
MSWS-12R2-ST2S
MSWS-12-DC2S-NS
MSWS-12R2-ST2S-NS
Red Hat
RHEL-2S2V-3A
Windows
Windows
Windows
Windows
Windows
Windows
Windows
RHEL-2S2V-1A
Red Hat Enterprise Linux (1-2 CPU,1-2 VN); 1-Yr Support Req
VMware
VMW-VSP-EPL-5A
VMware vSphere 6 Ent Plus (1 CPU), 5-yr, Support Required
VMW-VSP-STD-1A
VMware vSphere 6 Standard (1 CPU), 1-yr, Support Required
VMW-VSP-STD-3A
VMware vSphere 6 Standard (1 CPU), 3-yr, Support Required
VMW-VSP-EPL-3A
VMware vSphere 6 Ent Plus (1 CPU), 3-yr, Support Required
VMW-VSP-EPL-1A
VMware vSphere 6 Ent Plus (1 CPU), 1-yr, Support Required
VMW-VSP-STD-5A
VMware vSphere 6 Standard (1 CPU), 5-yr, Support Required
SLES SAP
SLES-SAP-2S2V-1S
SLES for SAP Apps (1-2 CPU, 1-2 VM); Priority 1-Yr SnS
SLES-SAP-2SUV-1S
SLES for SAP Apps (1-2 CPU, Unl VM); Priority 1-Yr SnS
SLES-SAP-2S2V-3S
SLES for SAP Apps (1-2 CPU, 1-2 VM); Priority 3-Yr SnS
SLES-SAP-2SUV-3S
SLES for SAP Apps (1-2 CPU, Unl VM); Priority 3-Yr SnS
SLES-SAP-2S2V-5S
SLES for SAP Apps (1-2 CPU, 1-2 VM); Priority 5-Yr SnS
SLES-SAP-2SUV-5S
SLES for SAP Apps (1-2 CPU, Unl VM); Priority 5-Yr SnS
SLES-SAP-2S2V-5A
SLES for SAP Apps (1-2 CPU, 1-2 VM); 5-Yr Support Reqd
SLES-SAP-2SUV-3A
SLES for SAP Apps (1-2 CPU, Unl VM); 3-Yr Support Reqd
SLES-SAP-2S2V-3A
SLES for SAP Apps (1-2 CPU, 1-2 VM); 3-Yr Support Reqd
SLES-SAP-2SUV-5A
SLES for SAP Apps (1-2 CPU, Unl VM); 5-Yr Support Reqd
SLES-SAP-2S2V-1A
SLES for SAP Apps (1-2 CPU, 1-2 VM); 1-Yr Support Reqd
SLES-SAP-2SUV-1A
SLES for SAP Apps (1-2 CPU, Unl VM); 1-Yr Support Reqd
SUSE
SLES-2S2V-1A
SLES-2SUV-1A
SLES-2S2V-3A
SLES-2SUV-3A
SLES-2S2V-5A
SLES-2SUV-5A
SLES-2S2V-1S
SUSE
SUSE
SUSE
SUSE
SUSE
SUSE
SUSE
56
Server
Server
Server
Server
Server
Server
Server
2012
2012
2012
2012
2012
2012
2012
Standard (2 CPU/2 VMs)
Datacenter (2 CPU/Unlimited VMs)
Standard (2 CPU/2 VMs) No Cisco SVC
R2 Datacen (2 CPU/Unlim VM) No Cisco Svc
R2 Standard (2 CPU/2 VMs)
Datacenter (2 CPU/Unlim VM) No Cisco Svc
R2 Standard (2 CPU/2 VMs) No Cisco SVC
Red Hat Enterprise Linux (1-2 CPU,1-2 VN); 3-Yr Support Req
Linux
Linux
Linux
Linux
Linux
Linux
Linux
Enterprise
Enterprise
Enterprise
Enterprise
Enterprise
Enterprise
Enterprise
Svr
Svr
Svr
Svr
Svr
Svr
Svr
(1-2
(1-2
(1-2
(1-2
(1-2
(1-2
(1-2
CPU,1-2 VM); 1-Yr Support Req
CPU,Unl VM); 1-Yr Support Req
CPU,1-2 VM); 3-Yr Support Req
CPU,Unl VM); 3-Yr Support Req
CPU,1-2 VM); 5-Yr Support Req
CPU,Unl VM); 5-Yr Support Req
CPU,1-2 VM); Prio 1-Yr SnS
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
CONFIGURING the SERVER
Table 26 Software (for 2-CPU servers) (continued)
PID Description
Product ID (PID)
SLES-2SUV-1S
SLES-2S2V-3S
SLES-2SUV-3S
SLES-2S2V-5S
SLES-2SUV-5S
SLES-2S-HA-1S
SLES-2S-HA-3S
SLES-2S-HA-5S
SLES-2S-GC-1S
SLES-2S-GC-3S
SLES-2S-GC-5S
SUSE
SUSE
SUSE
SUSE
SUSE
SUSE
SUSE
SUSE
SUSE
SUSE
SUSE
Linux
Linux
Linux
Linux
Linux
Linux
Linux
Linux
Linux
Linux
Linux
Enterprise Svr (1-2 CPU,Unl VM); Prio 1-Yr SnS
Enterprise Svr (1-2 CPU,1-2 VM); Prio 3-Yr SnS
Enterprise Svr (1-2 CPU,Unl VM); Prio 3-Yr SnS
Enterprise Svr (1-2 CPU,1-2 VM); Prio 5-Yr SnS
Enterprise Svr (1-2 CPU,Unl VM); Prio 5-Yr SnS
High Availability Ext (1-2 CPU); 1yr SnS
High Availability Ext (1-2 CPU); 3yr SnS
High Availability Ext (1-2 CPU); 5yr SnS
GEO Clustering for HA (1-2 CPU); 1yr Sns
GEO Clustering for HA (1-2 CPU); 3yr SnS
GEO Clustering for HA (1-2 CPU); 5yr SnS
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
57
CONFIGURING the SERVER
STEP 16 SELECT OPERATING SYSTEM MEDIA KIT
Select the optional operating system media listed in Table 27.
Table 27
58
OS Media
Product ID (PID)
PID Description
RHEL-6
RHEL 6 Recovery Media Only (Multilingual)
SLES-11
SLES 11 media only (multilingual)
MSWS-08R2-STHV-RM
Windows Svr 2008 R2 ST (1-4CPU, 5CAL), Media
MSWS-08R2-ENHV-RM
Windows Svr 2008 R2 EN (1-8CPU, 25CAL), Media
MSWS-08R2-DCHV-RM
Windows Svr 2008 R2 DC (1-8CPU, 25CAL), Media
MSWS-12-ST2S-RM
Windows Server 2012 Standard (2 CPU/2 VMs) Recovery Media
MSWS-12-DC2S-RM
Windows Server 2012 Datacenter(2 CPU/Unlimited VM) Rec Media
MSWS-12R2-ST2S-RM
Windows Server 2012 R2 Standard (2 CPU/2 VMs) Recovery Media
MSWS-12R2-DC2S-RM
Windows Server 2012 R2 Datacen (2 CPU/Unlimited VM) Rec Media
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
CONFIGURING the SERVER
STEP 17 SELECT SERVICE and SUPPORT LEVEL
A variety of service options are available, as described in this section.
Unified Computing Warranty, No Contract
If you have noncritical implementations and choose to have no service contract, the following
coverage is supplied:
■
Three-year parts coverage.
■
Next business day (NBD) onsite parts replacement eight hours a day, five days a week.
■
90-day software warranty on media.
■
Ongoing downloads of BIOS, drivers, and firmware updates.
■
UCSM updates for systems with Unified Computing System Manager. These updates include
minor enhancements and bug fixes that are designed to maintain the compliance of UCSM
with published specifications, release notes, and industry standards.
SMARTnet for UCS
For support of the entire Unified Computing System, Cisco offers the Cisco SMARTnet for UCS
Service. This service provides expert software and hardware support to help sustain
performance and high availability of the unified computing environment. Access to Cisco
Technical Assistance Center (TAC) is provided around the clock, from anywhere in the world.
For UCS blade servers, there is Smart Call Home, which provides proactive, embedded
diagnostics and real-time alerts. For systems that include Unified Computing System Manager,
the support service includes downloads of UCSM upgrades. The Cisco SMARTnet for UCS Service
includes flexible hardware replacement options, including replacement in as little as two hours.
There is also access to Cisco's extensive online technical resources to help maintain optimal
efficiency and uptime of the unified computing environment. You can choose a desired service
listed in Table 28.
Table 28
Cisco SMARTnet for UCS Service
Product ID (PID)
On Site?
Description
CON-PREM-C220M4SF
Yes
ONSITE 24X7X2 UCS C220 M4 SFF
CON-OSP-C220M4SF
Yes
ONSITE 24X7X4 UCS C220 M4 SFF
CON-OSE-C220M4SF
Yes
ONSITE 8X5X4 UCS C220 M4 SFF
CON-OS-C220M4SF
Yes
ONSITE 8X5XNBD UCS C220 M4 SFF
CON-S2P-C220M4SF
No
SMARTNET 24X7X2 UCS C220 M4 SFF
CON-SNTP-C220M4SF
No
SMARTNET 24X7X4 UCS C220 M4 SFF
CON-SNTE-C220M4SF
No
SMARTNET 8X5X4 UCS C220 M4 SFF
CON-SNT-C220M4SF
No
SMARTNET 8X5XNBD UCS C220 M4 SFF
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
59
CONFIGURING the SERVER
SMARTnet for UCS Hardware Only Service
For faster parts replacement than is provided with the standard Cisco Unified Computing System
warranty, Cisco offers the Cisco SMARTnet for UCS Hardware Only Service. You can choose from
two levels of advanced onsite parts replacement coverage in as little as four hours. SMARTnet
for UCS Hardware Only Service provides remote access any time to Cisco support professionals
who can determine if a return materials authorization (RMA) is required. You can choose a
service listed in Table 29.
Table 29
SMARTnet for UCS Hardware Only Service
Product ID (PID)
Service
Level GSP
On
Site?
Description
CON-UCW7-C220M4SF
UCW7
Yes
UCS HW 24X7X4OS UCS C220 M4 SFF
CON-UCW5-C220M4SF
UCW5
Yes
UC PLUS 8X5XNBDOS UCS C220 M4 SFF
Unified Computing Partner Support Service
Cisco Partner Support Service (PSS) is a Cisco Collaborative Services service offering that is
designed for partners to deliver their own branded support and managed services to enterprise
customers. Cisco PSS provides partners with access to Cisco's support infrastructure and assets
to help them:
■
Expand their service portfolios to support the most complex network environments
■
Lower delivery costs
■
Deliver services that increase customer loyalty
Partner Unified Computing Support Options enable eligible Cisco partners to develop and
consistently deliver high-value technical support that capitalizes on Cisco intellectual assets.
This helps partners to realize higher margins and expand their practice.
PSS is available to all Cisco PSS partners, but requires additional specializations and
requirements. For additional information, see the following URL:
www.cisco.com/go/partnerucssupport
The two Partner Unified Computing Support Options include:
■
Partner Support Service for UCS
■
Partner Support Service for UCS Hardware Only
Partner Support Service for UCS provides hardware and software support, including triage
support for third party software, backed by Cisco technical resources and level three support.
60
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
CONFIGURING the SERVER
See Table 30.
Table 30
Partner Support Service for UCS
Product ID (PID)
Service
Level
GSP
On
Site?
Description
CON-PSJ1-C220M4SF
PSJ1
No
UCS SUPP PSS 8X5XNBD UCS C220 M4 SFF
CON-PSJ2-C220M4SF
PSJ2
No
UCS SUPP PSS 8X5X4 UCS C220 M4 SFF
CON-PSJ3-C220M4SF
PSJ3
No
UCS SUPP PSS 24X7X4 UCS C220 M4 SFF
CON-PSJ4-C220M4SF
PSJ4
No
UCS SUPP PSS 24X7X2 UCS C220 M4 SFF
Partner Support Service for UCS Hardware Only provides customers with replacement parts in as
little as two hours. See Table 31.
Table 31
Partner Support Service for UCS (Hardware Only)
Product ID (PID)
Service
Level GSP
On
Site?
Description
CON-PSW2-C220M4SF
PSW2
No
UCS W PL PSS 8X5X4 UCS C220 M4 SFF
CON-PSW3-C220M4SF
PSW3
No
UCS W PL PSS 24X7X4 UCS C220 M4 SFF
CON-PSW4-C220M4SF
PSW4
No
UCS W PL PSS 24X7X2 UCS C220 M4 SFF
Unified Computing Combined Support Service
Combined Services makes it easier to purchase and manage required services under one
contract. SMARTnet services for UCS help increase the availability of your vital data center
infrastructure and realize the most value from your unified computing investment. The more
benefits you realize from the Cisco Unified Computing System (Cisco UCS), the more important
the technology becomes to your business. These services allow you to:
■
Optimize the uptime, performance, and efficiency of your UCS
■
Protect your vital business applications by rapidly identifying and addressing issues
■
Strengthen in-house expertise through knowledge transfer and mentoring
■
Improve operational efficiency by allowing UCS experts to augment your internal staff
resources
■
Enhance business agility by diagnosing potential issues before they affect your operations
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
61
CONFIGURING the SERVER
You can choose a service listed in Table 32.
Table 32
UCS Computing Combined Support Service
Product ID (PID)
Service
Level GSP
On
Site?
Description
CON-NCF2-C220M4SF
NCF2
No
CMB SPT SVC 24X7X2 UCS C220 M4 SFF
CON-NCF2P-C220M4SF
NCF2P
Yes
CMB SPT SVC 24X7X2OS UCS C220 M4 SFF
CON-NCF4P-C220M4SF
NCF4P
Yes
CMB SPT SVC 24X7X4OS UCS C220 M4 SFF
CON-NCF4S-C220M4SF
NCF4S
Yes
CMB SPT SVC 8X5X4OS UCS C220 M4 SFF
CON-NCFCS-C220M4SF
NCFCS
Yes
CMB SPT SVC 8X5XNBDOS UCS C220 M4 SFF
CON-NCFE-C220M4SF
NCFE
No
CMB SPT SVC 8X5X4 UCS C220 M4 SFF
CON-NCFP-C220M4SF
NCFP
No
CMB SPT SVC 24X7X4 UCS C220 M4 SFF
CON-NCFT-C220M4SF
NCFT
No
CMB SPT SVC 8X5XNBD UCS C220 M4 SFF
Unified Computing Drive Retention Service
With the Cisco Unified Computing Drive Retention (UCDR) Service, you can obtain a new disk
drive in exchange for a faulty drive without returning the faulty drive. In exchange for a Cisco
replacement drive, you provide a signed Certificate of Destruction (CoD) confirming that the
drive has been removed from the system listed, is no longer in service, and has been destroyed.
Sophisticated data recovery techniques have made classified, proprietary, and confidential
information vulnerable, even on malfunctioning disk drives. The UCDR service enables you to
retain your drives and ensures that the sensitive data on those drives is not compromised, which
reduces the risk of any potential liabilities. This service also enables you to comply with
regulatory, local, and federal requirements.
If your company has a need to control confidential, classified, sensitive, or proprietary data, you
might want to consider one of the Drive Retention Services listed in Table 33.
NOTE: Cisco does not offer a certified drive destruction service as part of this
service.
Table 33 Drive Retention Service Options
Service Description
Service
Program Name
SMARTnet for UCS
Service with Drive
Retention
UCS DR
62
Service
Level GSP
Service Level
Product ID (PID)
UCSD7
24x7x4 Onsite
CON-UCSD7-C220M4SF
UCSD5
8x5xNBD Onsite
CON-UCSD5-C220M4SF
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
CONFIGURING the SERVER
Table 33 Drive Retention Service Options (continued)
Service Description
Service
Program Name
SMARTnet for UCS
HW ONLY+Drive
Retention
UCS HW+DR
Service
Level GSP
Service Level
Product ID (PID)
UCWD7
24x7x4 Onsite
CON-UCWD7-C220M4SF
UCWD5
8x5xNBD Onsite
CON-UCWD5-C220M4SF
For more service and support information, see the following URL:
http://www.cisco.com/en/US/services/ps2961/ps10312/Unified_Computing_Services_Overview.pdf
For a complete listing of available services for Cisco Unified Computing System, see this URL:
http://www.cisco.com/en/US/products/ps10312/serv_group_home.html
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
63
OPTIONAL STEP - ORDER RACK(s)
OPTIONAL STEP - ORDER RACK(s)
The optional R42610 rack is available from Cisco for the C-Series servers, including the C220 M4
SFF server. This rack is a standard 19-inch rack and can be ordered with a variety of options, as
listed in Table 34. Racks are shipped separately from the C220 M4 SFF server.
Table 34
Racks and Rack Options
Product ID (PID)
PID Description
RACK-UCS1
Cisco R42610 expansion rack, no side panels
RACK-UCS21
Cisco R42610 standard rack, w/side panels
RACK-BLANK-001
Filler panels (qty 12), 1U, plastic, toolless
RACK-CBLMGT-001
Cable mgt D rings (qty 10), metal
RACK-CBLMGT-011
Cable mgt straps (qty 10), Velcro
RACK-FASTEN-001
Mounting screws (qty 100), M6
RACK-FASTEN-002
Cage nuts (qty 50), M6
RACK-JOIN-001
Rack joining kit
Notes . . .
1. Use these same base PIDs to order spare racks (available only as next-day replacements).
For more information about the R42610 rack, see RACKS, page 83.
64
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
OPTIONAL STEP - ORDER PDU
OPTIONAL STEP - ORDER PDU
An optional power distribution unit (PDU) is available from Cisco for the C-Series rack servers,
including theC220 M4 server. This PDU is available in a zero rack unit (RU) style (see Table 34).
Table 35
PDU Options
Product ID (PID)
PID Description
RP208-30-2P-U-2
Zero RU PDU
For more information about the PDU, see PDUs, page 85.
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
65
SUPPLEMENTAL MATERIAL
SUPPLEMENTAL MATERIAL
CHASSIS
An internal view of the C220 M4 chassis with the top cover removed is shown in Figure 6.
Figure 6
C220 M4 SFF With Top Cover Off
2
3
4
6
5
7
8
PSU 2
SD 1
FAN 6
9
FAN 5
CPU 2
PSU 1
SD 2
FAN 4
10
PCIe Riser 2
1
11
FAN 3
PCIe Riser 1
12
CPU 1
FAN 2
FAN 1
17
16
15
14
352978
13
1
Drives (SAS/SATA drives are hot-swappable)
10
Trusted platform module (TPM) socket on
motherboard (not visible in this view)
2
Cooling fan modules (six)
11
PCIe riser 2 (half-height PCIe slot 2)
3
SuperCap backup unit mounting location
12
PCIe riser 1 (full-height PCIe slot 1)
4
DIMM sockets on motherboard (24)
13
Modular LOM (mLOM) connector on chassis
floor
5
CPUs and heatsinks (up to two)
14
Cisco modular RAID controller PCIe riser
(dedicated riser with horizontal socket)
6
Embedded SATA RAID header for RAID 5 key
15
Cisco modular RAID controller card
7
SD card bays on motherboard (two)
16
Embedded SATA RAID mini-SAS connectors
on motherboard (not visible in this view)
8
Internal USB 3.0 port on motherboard
17
RTC battery on motherboard
9
Power supplies (up to two, hot-swappable
when redundant as 1+1)
66
—
—
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
4
3
2
1
5
6
7
8
3
4
2
1
SAS x2
SAS x2
UCSC-C220-M4L, 1U, 4-3.5" drives
*PCIe drives allowed in
slots 1 and 2 only
SAS x4
SAS x1
SAS x1
SAS x1
PCIe x4*
SAS x1
PCIe x4*
UCSC-C220-M4S, 1U, 8-2.5" drives
Cables to
modular
RAID card
Cable to
modular
RAID card or
Wellsburg
connector
Cable to
modular
RAID card or
Wellsburg
connector
or PCIe riser
2 (option 2)
Two Options for Drive Backplane
X4 SAS
Connector
X4 SAS
Connector
X4 SAS
Connector
X4 SAS
Connector
Gen3
(12 Gb/s)
H1H2 H3
G1G2 G3
F1 F2 F3
E1 E2 E3
D1D2 D3
C1C2 C3
B1B2 B3
A1A2 A3
Gen2
(6 Gb/s)
X4 SAS
Connector
X4 SAS
Connector
X4 SAS
Connector
SAS/SATA
SAS/SATA
Chan H
Chan G
Chan F
Chan E
Chan D
Chan C
Chan B
Chan A
SATA
SATA
SD1
Modular RAID
Card
Intel
Xeon
Haswell XP
(CPU 2)
QPI (9.6 GT)
SD2
PCIe
PCIe
PCIe x8 Gen 3
QPI (9.6 GT)
SD 3.0
SD controller
Intel
Xeon
Haswell XP
(CPU 1)
DMI2
DMI2 (x4)
Gen2
Intel
Wellsburg PCH
USB 3.0
USB
Thumbdrive
BMC
. . . . . . . . . . . .
PCIe x4 Gen3
X2 mini
SAS HD
Slot 2
PCIe Riser 2 (option 2)
Slot 2
PCIe Riser 2 (option 1)
PCIe x4 Gen3
PCIe x8 Gen3
PCIe x8 Gen3
PCIe x16 Gen3
Slot 1
PCIe Riser 1
PCIe x8 Gen 3 slot
PCIe x16 Gen3
PCIe x8 Gen 3
(a variety of network cards
can be installed here)
mLOM
Module
GbE switch
2-port
i350 NIC
Rear Panel
KVM
Connector
Front Panel
X2 USB 2.0
1 VGA
1 Serial
1 GB-T
(Mgmt)
1 GB-T
1 GB-T
Serial
VGA
USB
USB
Figure 7
X4 SAS
Connector
Network connectors
(types vary with mLOM module)
Cisco C220 M4 1U Server System Block Diagram
SUPPLEMENTAL MATERIAL
Block Diagram
A simplified block diagram of the C220 M4 server is shown in Figure 7.
C220 M4 SFF Block Diagram (simplified)
67
SUPPLEMENTAL MATERIAL
CPUs and DIMMs
Physical Layout
Each CPU has four DIMM channels:
■
CPU1 has channels A, B, C, and D
■
CPU2 has channels E, F, G, and H
Each DIMM channel has three slots: slot 1, slot 2, and slot 3. The blue-colored DIMM slots are for slot 1, the
black-colored slots for slot 2, and the white slots for slot 3.
As an example, DIMM slots A1, B1, C1, and D1 belong to slot 1, while A2, B2, C2, and D2 belong to slot 2.
Figure 8 shows how slots and channels are physically laid out on the motherboard. The DIMM slots on the
right half of the motherboard (channels A, B, C, and D) are associated with CPU 1, while the DIMM slots on
the left half of the motherboard (channels E, F, G, and H) are associated with CPU 2. The slot 1 (blue) DIMM
slots are always located farther away from a CPU than the corresponding slot 2 (black) and slot 3 (white)
slots. Slot 1 slots (blue) are populated before slot 2 slots (black) and slot 3 (white) slots.
Figure 8
68
Physical Layout of CPU DIMM Channels and Slots
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
SUPPLEMENTAL MATERIAL
Memory Population Rules
When considering the memory configuration of your server, you should consider the following items:
■
■
Each channel has three DIMM slots (for example, channel A = slots A1, A2, and A3).
—
A channel can operate with one, two, or three DIMMs installed.
—
If a channel has only one DIMM, populate slot 1 first (the blue slot).
When both CPUs are installed, populate the DIMM slots of each CPU identically.
—
Fill blue slots in the channels first: A1, E1, B1, F1, C1, G1, D1, H1
—
Fill black slots in the channels second: A2, E2, B2, F2, C2, G2, D2, H2
—
Fill white slots in the channels third: A3, E3, B3, F3, C3, G3, D3, H3
■
Any DIMM installed in a DIMM socket for which the CPU is absent is not recognized.
■
Observe the DIMM mixing rules shown in Table 36
Table 36 DIMM Rules for C220 M4 Servers
DIMM Parameter
DIMMs in the Same Channel
DIMM in the Same Slot1
DIMMs in the same channel (for
example, A1, A2, and A3) can have
different capacities.
For best performance, DIMMs in the
same slot (for example, A1, B1, C1,
D1) should have the same capacity.
Do not mix TSV-RDIMMS with
LRDIMMs nor RDIMMs
Do not mix TSV-RDIMMS with LRDIMMs
nor RDIMMs
DIMMs will run at the lowest speed
of the CPU installed
DIMMs will run at the lowest speed of
the CPU installed
Do not mix DIMM types in a channel
Do not mix DIMM types in a slot
DIMM Capacity
RDIMM = 8, 16, or 32 GB
LRDIMM = 32 or 64 GB
TSV-RDIMM = 64 GB
DIMM Speed
2400-MHz
2133-MHz
DIMM Type
TSV-RDIMMS, RDIMMs, or
LRDIMMs
1 DPC, 2 DPC, or 3 DPC
DIMMs per Channel (DPC)
See Table 5 on page 22 for
valid LRDIMM and RDIMM 1 DPC, 2 DPC, and 3 DPC memory configurations
Notes . . .
1. Although you can have different DIMM capacities in the same slot, this will result in less than optimal
performance. For optimal performance, all DIMMs in the same slot should be identical.
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
69
SUPPLEMENTAL MATERIAL
DIMM Population Order
Populate the DIMMs for a CPU according to Table 37.
Table 37
DIMMs
per CPU
Populate
CPU 1 Slots
Populate
CPU 2 Slots
1
A1
E1
2
A1, B1
E1, F1
3
A1, B1, C1
E1, F1, G1
4
A1, B1, C1, D1
E1, F1, G1, H1
8
A1, B1, C1, D1,
E1, F1, G1, H1,
A2, B2, C2, D2
E2, F2, G2, H2
A1, B1, C1, D1,
E1, F1, G1, H1,
A2, B2, C2, D2,
E2, F2, G2, H2,
A3, B3, C3, D3
E3, F3, G3, H3
12
70
DIMM Population Order per CPU
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
SUPPLEMENTAL MATERIAL
Recommended Memory Configuration
This section explains the recommended DIMM population order rules for the C220 M4 server.
■
■
■
■
All DIMMs must be DDR4 DIMMs.
Do not mix:
— DIMMs with different clock rates in a channel
— RDIMMs and LRDIMMs
There are blue, black, and white DIMM slots. Populate blue slots first.
When DIMMs ranks are mixed in the same channel, always populate the highest rank DIMM in
the blue DIMM slot and lower rank DIMM(s) in the black and white DIMM slots.
Many memory configurations are possible. For best results, follow Table 38 when populating 2133-MHz
DIMMs for Intel Xeon E5-2600 v3 CPUs and Table 39 when populating 2400-MHz DIMMs for Intel Xeon E5-2600
v4 CPUs.
NOTE: These tables list only some recommended and suggested configurations.
There are numerous other possible configurations supported by Cisco. Cisco supports
all mixing and population configurations of the Cisco DIMMs as long as the mixing
does not violate the few fundamental rules noted in this document.
Table 38 Recommended Memory Configurations for Intel Xeon E5-2600 v3 CPUs (with 2133-MHz DIMMs)1
Total
System
Memory
Size
64 GB
CPU 1 DIMMs
CPU 2 DIMMs
Blue Slots Black Slots White Slots Blue Slots Black Slots White Slots DIMM Max
Speed
Slot 1
Slot 2
Slot 3
Slot 1
Slot 2
Slot 3
(MHz)
(A1,B1,
(A2,B2,
(A3,B3,
(E1,F1,
(E2,F2,
(E3,F3,
C1,D1)
C2,D2)
C3,D3)
G1,H1)
G2,H2)
G3,H3)
4x8 GB
—
—
4x8 GB
—
—
2133
Total
DIMMs
8
4x8 GB
4x8 GB
—
4x8 GB
4x8 GB
—
2133
16
4x16 GB
—
—
4x16 GB
—
—
2133
8
4x8 GB
4x8 GB
4x8 GB
4x8 GB
4x8 GB
4x8 GB
1600
24
4x16 GB
4x8 GB
—
4x16 GB
4x8 GB
—
2133
16
4x16 GB
4x16 GB
—
4x16 GB
4x16 GB
—
2133
16
4x32 GB
—
—
4x32 GB
—
—
2133
8
384 GB
4x16 GB
4x16 GB
4x16 GB
4x16 GB
4x16 GB
4x16 GB
1866
24
512 GB
4x32 GB
4x32 GB
—
4x32 GB
4x32 GB
—
2133
16
4x64 GB
—
—
4x64 GB
—
—
2133
8
768 GB
4x32 GB
4x32 GB
4x32 GB
4x32 GB
4x32 GB
4x32 GB
1866
24
1024 GB
4x64 GB
4x64 GB
—
4x64 GB
4x64 GB
—
2133
16
1536 GB
4x64 GB
4x64 GB
4x64 GB
4x64 GB
4x64 GB
4x64 GB
1600
24
128 GB
192 GB
256 GB
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
71
SUPPLEMENTAL MATERIAL
Notes . . .
1. Rows marked in yellow indicate best performance.
Table 39 Recommended Memory Configurations for Intel Xeon E5-2600 v4 CPUs (with 2400-MHz DIMMs)1
Total
System
Memory
Size
128 GB
CPU 1 DIMMs
CPU 2 DIMMs
Blue Slots Black Slots White Slots Blue Slots Black Slots White Slots DIMM Max
Speed
Slot 1
Slot 2
Slot 3
Slot 1
Slot 2
Slot 3
(MHz)
(A1,B1,
(A2,B2,
(A3,B3,
(E1,F1,
(E2,F2,
(E3,F3,
C1,D1)
C2,D2)
C3,D3)
G1,H1)
G2,H2)
G3,H3)
4x16 GB
—
—
4x16 GB
—
—
2400
Total
DIMMs
8
192 GB
4x16 GB
4x8 GB
—
4x16 GB
4x8 GB
—
2400
16
256 GB
4x16 GB
4x16 GB
—
4x16 GB
4x16 GB
—
2400
16
4x32 GB
—
—
4x32 GB
—
—
2400
8
4x16 GB
4x16 GB
4x16 GB
4x16 GB
4x16 GB
4x16 GB
2133
24
4x32GB
4x16GB
—
4x32GB
4x16GB
—
2400
16
4x32 GB
4x32 GB
—
4x32 GB
4x32 GB
—
2400
16
4x64 GB
—
—
4x64 GB
—
—
2400
8
768 GB
4x32 GB
4x32 GB
4x32 GB
4x32 GB
4x32 GB
4x32 GB
2133
24
1024 GB
4x64 GB
4x64 GB
—
4x64 GB
4x64 GB
—
2400
16
1536 GB
4x64 GB
4x64 GB
4x64 GB
4x64 GB
4x64 GB
4x64 GB
2133
24
384 GB
512 GB
Notes . . .
1. Rows marked in yellow indicate best performance.
72
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
SUPPLEMENTAL MATERIAL
Additional DIMM Populations
The list in Table 40 is not a complete list of all supported DIMM populations, but highlights common
configuration options.
Table 40 Supported DIMM Configurations
Total DIMMs
for CPU 2
CPU 2
Capacity
Total
Capacity for
2 CPUs
1 x 8 GB
1
8 GB
16 GB
16 GB
2 x 8 GB
2
16 GB
32 GB
1
16 GB
1 x 16 GB
1
16 GB
32 GB
4 x 8 GB
4
32 GB
4 x 8 GB
4
32 GB
64 GB
2 x 16 GB
2
32 GB
2 x 16 GB
2
32 GB
64 GB
1 x 32 GB
1
32 GB
1 x 32 GB
1
32 GB
64 GB
8 x 8 GB
8
64 GB
8 x 8 GB
8
64 GB
128 GB
4 x 16 GB
4
64 GB
4 x 16 GB
4
64 GB
128 GB
2 x 32 GB
2
64 GB
2 x 32 GB
2
64 GB
128 GB
12 x 8 GB
12
96 GB
12 x 8 GB
12
96 GB
192 GB
8 x 16 GB
8
128 GB
8 x 16 GB
8
128 GB
256 GB
4 x 32 GB
4
128 GB
4 x 32 GB
4
128 GB
256 GB
12 x 16 GB
12
192 GB
12 x 16 GB
12
192 GB
384 GB
8 x 32 GB
8
256 GB
8 x 32 GB
8
256 GB
512 GB
12 x 32 GB
12
384 GB
12 x 32 GB
12
384 GB
768 GB
12 x 64 GB
12
768 GB
12 x 32 GB
12
768 GB
1536 GB
Total DIMMs
for CPU 1
CPU 1
Capacity
1 x 8 GB
1
8 GB
2 x 8 GB
2
1 x 16 GB
CPU 1 DIMMs
CPU 2 DIMMs
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
73
SUPPLEMENTAL MATERIAL
RAID Details
The available RAID configurations are shown in this section.
By default, the server comes with embedded software RAID
To upgrade from the default, select one of these:
■
The embedded software RAID 5 key upgrade option from Table 7 on page 27, or
■
One Cisco 12G SAS Modular RAID controller upgrade or Cisco 12 Gbps Modular SAS HBA from
Table 8 on page 27, or
■
One or two Cisco 9300-8E 12G SAS HBA controllers from Table 8 on page 27, or
■
One Cisco 12G SAS Modular RAID controller or Cisco 12 Gbps Modular SAS HBA from Table 8
on page 27 and one or two Cisco 9300-8E 12G SAS HBAs from Table 8 on page 27
Select an appropriate optional RAID configuration listed in Table 8 on page 27
74
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
SUPPLEMENTAL MATERIAL
RAID Option ROM (OPROM) Settings
The server contains an Option ROM (OPROM) for the PCIe slots. The server has a finite amount of option
ROM with which it can boot up devices. Go into the BIOS and disable the OPROM on the PCIe slots not used
for booting so that resources are available for the slots that are used for booting. An example OPROM BIOS
screen is shown in Figure 9.
Figure 9
Example BIOS Screen for OPROM
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
75
SUPPLEMENTAL MATERIAL
Embedded SATA RAID: Two SATA Controllers
The embedded SATA RAID controller hub is split into two controllers, SATA and sSATA (secondary SATA).
These two controllers are seen as separate RAID controllers in the Cisco IMC interface and are configurable
separately.
■
The first SATA controller controls drives 1–4; the secondary sSATA controller controls drives 5–8.
■
When configuring RAID groups, you cannot create a group that spans more than four drives.
■
The first SATA controller can control a RAID group of up to four drives, consisting only of
drives 1–4.
■
The secondary sSATA controller can control a RAID group of up to four drives, consisting only
of drives 5–8. See Figure 10.
Embedded RAID Controller RAID Groups
HDD 01
HDD 04
HDD 02
HDD 05
HDD 03
HDD 06
HDD 07
HDD 08
353092
Figure 10
SATA RAID Controller Hub
SATA
■
sSATA
Each controller is listed separately in the BIOS. You can select the boot order of the
controllers in the BIOS (use the Boot Options tab in the BIOS Setup Utility).
Note the following considerations:
76
■
The default setting for this embedded controller hub is SATA RAID 0, 1, and 10 support for up to
eight SATA drives (in two groups of four drives).
■
You can upgrade this to support to SATA RAID 0, 1, 10, and 5 support for up to eight SATA drives (in
two groups of four drives) by installing a RAID 5 key module on the motherboard.
■
When you order the server with this embedded controller, the controller is enabled in the BIOS.
■
You cannot downgrade from using a HW RAID controller card to using the SW RAID embedded
controller.
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
SUPPLEMENTAL MATERIAL
To Create a RAID Group
(1) While the server is booting, wait for the prompt and press function key F2 as shown in
Figure 11.
Figure 11
Function Key F2 Prompt
In a few seconds, you will see the screen that allows you to set up a RAID group for the primary
SATA controller (see Figure 12).
Figure 12
Screen to Configure Primary SATA RAID Group
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
77
SUPPLEMENTAL MATERIAL
(2) Press Ctrl+M to start the RAID group creation process for the primary SATA controller (for
drives 1-4, as shown in Figure 10 on page 76). Or, do nothing and wait for the next screen,
which allows you to create a RAID group for the secondary SATA (sSATA) controller see
Figure 13).
Figure 13
Screen to Configure Secondary SATA (sSATA) RAID Group
(3) Press Ctrl+M to start the RAID group creation process for the secondary SATA (sSATA)
controller (for drives 5-8, as shown in Figure 10 on page 76).
78
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
SUPPLEMENTAL MATERIAL
Serial Port Details
The pinout details of the rear RJ-45 serial port connector are shown in Figure 14.
Figure 14
Serial Port (Female RJ-45 Connector) Pinout
Serial Port (RJ-45 Female Connector)
Pin Signal
1
2
3
4
5
6
7
8
RTS (Request to Send)
DTR (Data Terminal Ready)
TxD (Transmit Data)
GND (Signal Ground)
GND (Signal Ground)
RxD (Receive Data)
DSR (Data Set Ready)
CTS (Clear to Send)
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
79
SUPPLEMENTAL MATERIAL
Upgrade and Servicing-Related Parts
This section lists the upgrade and servicing-related parts you may need during the life of your server. Some
of these parts are configured with every server, and some may be ordered when needed or may be ordered
and kept on hand as spares for future use. See Table 41.Drive Blanking Panels
Table 41 Upgrade and Servicing-related Parts for UCS C220 M4 LFF Server
Spare Product ID (PID)
Description
UCSC-HS-C220M4=
Heat sink for UCS C220 M4 rack servers
UCS-CPU-GREASE3=
M4 Server CPU thermal grease syringe - needed for heatsink seal
UCS-CPU-LPCVR=
CPU load plate dust cover (for unpopulated CPU sockets)
UCSX-HSCK=
UCS Processor Heat Sink Cleaning Kit For Replacement of CPU
UCSC-PCI-2A-220M4=
C220 M4 PCIe Riser 1&2 Assy
UCSC-PCI-2C-220M4=
C220 M4 PCIe Riser 3 (HBA)
UCSC-PCIF-01H=
PCIe Low Profile blanking panel for UCS C-Series Server
UCSC-PCIF-01F=
PCIe Full Height blanking panel for UCS C-Series Server
N20-BBLKD
HDD blanking panel1
UCSC-MLOM-BLK=
MLOM blanking panel
UCSC-RAILF-M4=
Tool-Less Friction Rail Kit for C220 M4 rack servers
UCSC-CMAF-M4=
Reversible CMA for C220 M4 friction & ball bearing rail kits
UCSC-RAILB-M4=
Tool-Less Ball Bearing Rail Kit for C220 M4 and C220 M4 rack servers
UCSC-FAN-C220M4=
C220 M4 Fan Module (one)
UCSC-BAFF-C220M4=
C220 M4 Air Baffle, Plastic Kit
N20-BKVM=
KVM cable for Server console port
UCSC-PSU-BLKP1U=
Power Supply Blanking Panel for C220 M4 servers
UCS-220CBLSR8=
C220 M4 set of 2 SATA/SW RAID cables for 8HDD bckpln chassis2
UCS-220CBLMR8=
C220 M4 set of 2 RAID cntrlr cables for 8HDD bckpln chassis2
UCSC-EARS-C220M4=
C200 M4 rack ears kit (two ears)
UCSC-PCI-2B-220M4=
C220 M4 PCIe Riser 1&2 Assy + PCIe SSD connector 8639
Notes . . .
1. A drive blanking panel must be installed if you remove a disk drive from a UCS server. These panels are
required to maintain system temperatures at safe operating levels, and to keep dust away from system
components.
2. Required if ordering the RAID controller as a spare or to replace damaged cables
80
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
SUPPLEMENTAL MATERIAL
Adding an Additional CPU (with CPU heat sink) or Replacing CPUs
All Cisco UCS two CPU socket-capable servers can be upgraded from having one to having two CPUs
configured or can also support replacement of the CPUs. You will need to order and install a heat sink when
adding any additional CPU to a server. Instructions for installing the new CPU or replacing CPUs and heat
sink can be found at the following link:
http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c/hw/C220M4/install/C220M4.html
NOTE: Unlike previous generation servers, the C220 M4 has tool-less CPU sockets, so
no separate tools (such as “pick n place” tools) are required to add or replace CPUs.
See the section titled “Replacing CPUs and Heatsinks.”
Motherboard Lithium Battery
You can order a replacement motherboard battery. Installation instructions are found at this link:
http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c/hw/C220M4/install/C220M4.html
See the section titled “Replacing the Motherboard RTC Battery.”
Thermal Grease (with syringe applicator) for CPU to Heatsink Seal
Thermal grease must be applied to the top of the CPU where it comes in contact with the heat sink (a
grease syringe also ships with each CPU spare option kit). Instructions for applying thermal grease are found
at:
http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c/hw/C220M4/install/C220M4.html
See the section titled “Replacing CPUs and Heatsinks.”
CAUTION: Use only the thermal grease specified for this server
(UCS-CPU-GREASE3=). This thermal grease comes in a white-tipped
syringe and is to be used only in the C220 M4 and C240 M4 servers. Other
servers use thermal grease in a blue-tipped syringe (UCS-CPU-GREASE=).
Thermal grease for other systems may have different thermal
conductivity properties and may cause overheating if used in the C220 M4
or C240 M4 servers.
DO NOT use thermal grease available for purchase at any commercial
electronics store. If these instructions are not followed, the CPU may
overheat and be destroyed.
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
81
SUPPLEMENTAL MATERIAL
NOTE: When you purchase a spare CPU, the thermal grease with syringe applicator
is included.
Air Baffle Replacement Kit
Air baffles are designed to direct airflow through the server to maintain server temperature at a safe
operating level. These baffles must always remain installed during server operation. The Air Baffle
Replacement Kit includes the air baffles needed for one UCS C220 M4 server.
CPU Heat Sink Cleaning Kit
The cleaning kit is used to remove the existing thermal compound from the bottom of the heat sink during
a CPU replacement process. Instructions for cleaning are found at the following link:
http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c/hw/C220M4/install/C220M4.html
See the section titled “Replacing CPUs and Heatsinks.”
NOTE: When you purchase a spare CPU, the CPU cleaning kit is included.
82
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
SUPPLEMENTAL MATERIAL
RACKS
The Cisco R42610 rack (see Figure 15) is certified for Cisco UCS installation at customer sites and is
suitable for the following equipment:
■
Cisco UCS B-Series servers and fabric interconnects
■
Cisco UCS C-Series and select Nexus switches
The rack is compatible with hardware designed for EIA-standard 19-inch racks. Rack specifications are
listed in Table 42.
Table 42 Cisco R42610 Rack Specifications
Parameter
Standard Rack
Expansion Rack
Dimensions (H x W x D)
78.74 x 24 x 43.38 in.
(2000 x 610 x 1102 mm)
78.74 x 23.58 x 43.38 in.
(2000 x 599 x 1102 mm)
Dimensions (H x W x D)
with packaging
89 x 33 x 47 in.
(2261 x 838 x 1194 mm)
89 x 33 x 47 in.
(2261 x 838 x 1194 mm)
Distance from front
mounting rail to rear
mounting rail
29.2 in (741 mm)
29.2 in (741 mm)
Weight
299.83 lb (136 kg)
231. 49 lb (105 kg)
Weight with packaging
354 lb
(161 kg)
284 lb
(129 kg)
Side panels included
Yes
No
Equipment mounting
capacity
42RU
42RU
Static load capacity
2100 lb
(954 kg)
2100 lb
(954 kg)
Dynamic load capacity
Not applicable
Not applicable
NOTE: The AC input connector is an IEC 320 C-14 15 A/250 VAC power inlet.
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
83
SUPPLEMENTAL MATERIAL
Figure 15
Cisco R42610 Rack
Front view - door
84
Front view - door open
Front view - door removed
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
SUPPLEMENTAL MATERIAL
PDUs
Cisco RP Series Power Distribution Units (PDUs) offer power distribution with branch circuit protection.
Cisco RP Series PDU models distribute power to up to 24 outlets. The architecture organizes power
distribution, simplifies cable management, and enables you to move, add, and change rack equipment
without an electrician.
With a Cisco RP Series PDU in the rack, you can replace up to two dozen input power cords with just one.
The fixed input cord connects to the power source from overhead or under-floor distribution. Your IT
equipment is then powered by PDU outlets in the rack using short, easy-to-manage power cords.
The C-series severs accept the zero-rack-unit (0RU) PDU. See Figure 16).
Figure 16
Zero Rack Unit PDU (PID = RP208-30-2P-U-2)
1
Breakers
3
C19 plugs
2
Ground connection
4
C13 plugs
Cisco RP Series PDU models provide two 20-ampere (A) circuit breakers for groups of receptacles. The
effects of a tripped circuit are limited to a receptacle group. Simply press a button to reset that circuit.
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
85
SUPPLEMENTAL MATERIAL
KVM CABLE
The KVM cable provides a connection into the server, providing a DB9 serial connector, a VGA connector for
a monitor, and dual USB ports for a keyboard and mouse. With this cable, you can create a direct
connection to the operating system and the BIOS running on the server.
The KVM cable ordering information is listed in Table 43.
Table 43 KVM Cable
Product ID (PID)
PID Description
N20-BKVM=
KVM cable for B-Series Blade Server console port
Figure 17
KVM Cable
1
Connector (to server front panel)
3
VGA connector (for a monitor)
2
DB-9 serial connector
4
Two-port USB connector (for a mouse and
keyboard)
86
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
SUPPLEMENTAL MATERIAL
Motherboard USB and SD Ports, and RAID Card Backup Location
The C220 M4 SFF motherboard has a general-purpose USB socket, and two SD sockets as shown in Figure 18.
The mounting location for the RAID SuperCap data cache power backup module is also shown.
Figure 18
Motherboard USB and SD Ports and RAID Card SuperCap Location
2
3
4
6
5
7
8
PSU 2
SD 1
FAN 6
9
FAN 5
CPU 2
PSU 1
SD 2
FAN 4
10
PCIe Riser 2
1
11
FAN 3
PCIe Riser 1
12
CPU 1
FAN 2
FAN 1
17
16
15
14
352978
13
1
Drives (SAS/SATA drives are hot-swappable)
10
Trusted platform module (TPM) socket on
motherboard (not visible in this view)
2
Cooling fan modules (six)
11
PCIe riser 2 (half-height PCIe slot 2)
3
SuperCap Power Module (RAID backup)
mounting bracket
12
PCIe riser 1 (full-height PCIe slot 1)
4
DIMM sockets on motherboard (24)
13
Modular LOM (mLOM) connector on chassis
floor
5
CPUs and heatsinks (up to two)
14
Cisco modular RAID controller PCIe riser
(dedicated riser with horizontal socket)
6
Embedded SATA RAID header for RAID 5 key
15
Cisco modular RAID controller card
7
SD card bays on motherboard (two)
16
Embedded SATA RAID mini-SAS connectors
on motherboard (not visible in this view)
8
Internal USB 3.0 port on motherboard
17
RTC battery on motherboard
9
Power supplies (up to two, hot-swappable
when redundant as 1+1)
—
—
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
87
TECHNICAL SPECIFICATIONS
TECHNICAL SPECIFICATIONS
Dimensions and Weight
Table 44 UCS C220 M4 Dimensions and Weight
Parameter
Value
Height
1.7 in. (4.32 cm)
Width
16.89 in. (43.0 cm)
including handles:
18.98 in. (48.2 cm)
Depth
29.8 in. (75.6 cm)
including handles:
30.98 in. (78.7 cm)
Front Clearance
3 in. (76 mm)
Side Clearance
1 in. (25 mm)
Rear Clearance
6 in. (152 mm)
Weight
88
Maximum (8 HDDs, 2 CPUs, 16 DIMMs, two power supplies)
37.9 lbs (17.2 kg)
Minimum (1 HDD, 1 CPU, 1 DIMM, one power supply)
30.5 lbs (13.8 kg)
Bare (0 HDD, 0 CPU, 0 DIMM, one power supply)
29.2 lbs (13.2 kg)
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
TECHNICAL SPECIFICATIONS
Power Specifications
The general power specifications for the C220 M4 SFF server 770 W (AC) power supply are listed in
Table 45.
Table 45 UCS C220 M4 SFF 770 W (AC) Power Supply Specifications
Description
Specification
AC input voltage
100—240 VAC (nominal input voltage range)
90—264 VAC (min/max input voltage range)
AC input frequency
47 to 63 Hz (single phase)
Maximum AC input current
9.5 Amps maximum at 100 VAC
4.5 Amps maximum at 208 VAC
Maximum Input VA
915 at 230 VAC
Maximum output power for each
power supply
770 W on 12 VDC main
Maximum AC inrush current
15 A (subcycle duration)
Power supply output voltage
12 VDC ± 5%
Power supply efficiency
Climate Savers Platinum Efficiency (80Plus Platinum Certified)
Form factor
RSP2
Input connector
IEC320 C14
36 W on 12 VDC standby
The general power specifications for the C220 M4 SFF server 1050 W (DC) power supply are listed in
Table 45.
Table 46 UCS C220 M4 SFF 1050 W (DC) Power Supply Specifications
Description
Specification
DC Input voltage range
Nominal range: –48 to –60 VDC nominal
(maximum range: –40 to –72 VDC)
Maximum DC input current
32 A at –40 VDC
Maximum input W
1234 W
Maximum output power per PSU
1050 W on 12 VDC main power
36 W on 12 VDC standby power
Maximum inrush current
15 A at -72 VDC
Maximum hold-up time
5 ms at 100% load (1050 W main and 36 W standby)
Power supply output voltage
12 VDC
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
89
TECHNICAL SPECIFICATIONS
Table 46 UCS C220 M4 SFF 1050 W (DC) Power Supply Specifications (continued)
Description
Specification
Power supply standby voltage
12 VDC
Efficiency rating
Greater than or equal to 92% at 50% load
Form factor
RSP2
Input connector
3 wire Connector (Molex MINIFIT SR. R/A)
For configuration-specific power specifications, use the Cisco UCS Power Calculator at this URL:
http://ucspowercalc.cisco.com
90
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
TECHNICAL SPECIFICATIONS
Environmental Specifications
The power specifications for the C220 M4 server are listed in Table 47.
Table 47 UCS C220 M4 SFF Environmental Specifications
Parameter
Minimum
Temperature operating
41 to 95° F (5 to 35° C)
derate the maximum temperature by 1°C per every
1000 ft. (305 m) of altitude above sea level
Temperature nonoperating
–40 to 149°F (–40 to 65° C)
Humidity (RH) operating
10 to 90%, non-condensing at 82° F (28° C)
Humidity (RH) nonoperating
5 to 93% at 82° F (28° C)
Altitude operating
0 to 3,000 m (0 to 10,000 ft.)
Altitude nonoperating
0 to 12,192 m (0 to 40,000 ft.)
Sound Power level, Measure
A-weighted per ISO7779 LWAd (Bels)
Operation at 73°F (23°C)
5.4
Sound Pressure level, Measure
A-weighted per ISO7779 LpAm (dBA)
Operation at 73°F (23°C)
37
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
91
TECHNICAL SPECIFICATIONS
Compliance Requirements
The regulatory compliance requirements for C-Series servers are listed in Table 48.
Table 48 UCS C-Series Regulatory Compliance Requirements
Parameter
Description
Regulatory Compliance
Products should comply with CE Markings per directives
2004/108/EC and 2006/95/EC
Safety
UL 60950-1 Second Edition
CAN/CSA-C22.2 No. 60950-1 Second Edition
EN 60950-1 Second Edition
IEC 60950-1 Second Edition
AS/NZS 60950-1
GB4943 2001
EMC - Emissions
47CFR Part 15 (CFR 47) Class A
AS/NZS CISPR22 Class A
CISPR22 Class A
EN55022 Class A
ICES003 Class A
VCCI Class A
EN61000-3-2
EN61000-3-3
KN22 Class A
CNS13438 Class A
EMC - Immunity
EN55024
CISPR24
EN300386
KN24
92
Cisco UCS C220 M4 High-Density Rack Server (Small Form Factor Disk Drive Model)
Download PDF
Similar pages