Nortel passport 7480 installation/conf. (STARTUP PROCEDURE)

Feb
19
Nortel passport 7480 installation/conf.
(STARTUP PROCEDURE)
When you connect the PC to console port you will get the prompt for entering login and
password if the passport has been programmed earlier. Enter these and come to the prompt.
Also remove Spare CP Card from slot No 15. Enter STARTUP command at the prompt to
configure the Passport from scratch. On entering this you will get the display
> STARTUP
The currently selected NMS Connectivity is:
An NMS via Passport IP Networking
The currently selected media type is:
OamEnet
NMS and Passport are on the same subnet
Do you wish to change the selected NMS connectivity[No]?
>
The above display may be different if some other NMS connectivity has been choosen for the
Passport in past.
Enter " yes", you will see following four options:-
1. A connection to NMS through a DPN Network
2. A connection to NMS through a Passport Network
3. A direct connection to NMS from this passport using Frame Relay PVC
4. A connection to NMS vis Passport IP Networking
[1]
>
Enter 4 in order to select management through Passport IP Networking
The passport will display the following:-
The follwing types of NMS connectivity has been selected:
A Connection to NMS via Passport IP Networking.
Media Type selection:-
1 ATM MPE
2. FRDTE
3. Ethernet
4. VNS
5. OamEnet
[1]
>
Enter 3 to select Ethernet media
Following will be displayed
The following IP Media type has been selected:
Ethernet
Is NMS and Passport on the same IP Subnt [No]?
Type "yes" then press "Enter" Key
System will tell you that it is waiting for all FPs to be recognized by the CP and will take 5
min
After this following will be displayed:-
Please enter "Quit" or select one of the following
1. Reset node to CP only software
2. Create sw lpts and load software on FPs
3. Perform on card tests of each card in the node
4. Configure the node for NMS connectivity
5. Display the cards inserted in the node
6. Provision a spare CP
7. Change the selected NMS connectivity
8. Confirm the provisioning
[5]
>
Type 1 and press Enter key
The following will be displayed
If you continue please confirm the following is satisfactory:-
A minimal provisioning file will be created and activated
The CP will activate using release base_CE01S1B
The node will reboot with this new provisioning file
Are you sure you want to continue?[No]
Type "Yes" and press Enter
The system will display the following:Please enter the following information required for CP Only software:-
Node ID[0]
Suppose your node ID is 110, enter 110 and press enter
Node Name [EM60]
Suppose your node name is LONDON, enter LONDON and press enter
NAMS Id[0]
Suppose your NAMS Id is 1110, enter 1110 and press enter
The system will display the following:-
Are these values correct? This will activate the provisioning[yes]
Select "yes" and press Enter
Following will be displayed on the screen:-
> start –force prov
///////////////////////////////////////////////////////////////////////////// (Many lines of text)
activate prov (Short pause)
///////////////////////////////////////////////////////////////////////////// (Many lines of text)
Forcing CP to boot using alternate provisiong file due to ACTIVATE PROV operators
command
Rebooting……………..
Firmware PM2 Version CE01S1B Creation date:…………….
****Booting a Central Processor****Testing bytes of memory at
NORTEL NETWORK PASSPORT
CPU………..
///////////////////////////////////////////////////////////////////////////// (Many lines of text)
Enter login:
You can type any letter as login say you type "abc" and press Enter
Enter Password:
Leave the password blank and press Enter
System will display:-
UserID abc. Logged in as NMIS Session/1 at 19.22.56
Note you have 20 min to complete provisioning or it will go back to original build
Again type startup at the command prompt to again invoke the startup facility
>STARTUP
System will display the following:-
You have not confirmed your current provisioning view.
Shall I issue the "Confirm prov" command for you?[Yes]
Type "Yes" and press Enter
System will display the following:-
Start –force prov …. Ok
Confirm prov ……
Prov: 1987-07-16 02:03:51
CLR cleared operator operation condition
/////////////////////////////////////////////////
/////////////////////////////////////////////
////////////////////////////////// (Few lines of text giving states)
Ok
End prov
Confirmation succeeded
The currently selected NMS connectivity is:
An NMS connected via Passport IP Networking
The currently selected media type is:
Ethernet
NMS and Passport are on one subnet
Do you wish to change the selected NMS Connectivity?[No]
Type "No" and press Enter.
Following will be displayed:-
Please enter "Quit" or select one of the following
1. Reset node to CP only software
2. Create sw lpts and load software on FPs
3. Perform on card tests of each card in the node
4. Configure the node for NMS connectivity
5. Display the cards inserted in the node
6. Provision a spare CP
7. Change the selected NMS connectivity
8. Confirm the provisioning
[5]
>
Type 2 and press Enter key
System will display the following:-
You have seleted the following software releases:
base_CE01S1B
ip_CE01S1B
Are you sure?[Yes]
Type Yes and press Enter key
System will display the following:-
Start –force prov
…ok
Set sw avlist base_CE01S1B
Set sw avlist ip_CE01S1B
…ok
…ok
////////////////////////////////////////////////////////////////////////
//////////////////////(Many lines of text)
STARTUP: Waiting for the FPs to come up It can take upto 5 minutes
> STARTUP Time remaining 300 seconds
STARTUP Time remaining 270 seconds
////////////////////////////////////////////////////////////////////////
//////////////////////(Many lines of text)
> STARTUP Time remaining 240seconds
STARTUP Time remaining 210 seconds
> STARTUP Time remaining 100 seconds
STARTUP : FP Cards come up
End prov
Please enter "Quit" or select one of the following
1. Reset node to CP only software
2. Create sw lpts and load software on FPs
3. Perform on card tests of each card in the node
4. Configure the node for NMS connectivity
5. Display the cards inserted in the node
6. Provision a spare CP
7. Change the selected NMS connectivity
8. Confirm the provisioning
[5]
>
Type 4 and press Enter key
System will display the following:-
STARTUP: Waiting for FPs to be recognized CP in case CP was rebooted. It takes up to 5
minutes. IP Connection Configuration:
Enter the startup configuration information as prompted or enter 'quit'
IP Port Address[aa.bb.cc.dd]
Suppose IP Port address is 192.168.210.1, type 192.168.210.1 and press Enter
IP Port Network Mask[}
Suppost Network Mask is 255.255.255.0, type 255.255.255.0 and Enter
IP Broadcast Address[aa.bb.cc.dd]
In above example it will be 192.168.210.255, type 192.168.210.255 and Enter
The system will show a table indicating which card is in which slot. One of the sample of
display is as under
+--+--+--+--+--+--+--+--+--+--+--+--+--+--+-|C||I|2|||2||3|||||
|P||L|P|||p||p|||||
|e||s|e|||o||e|||||
|d||f|t|||c||3|||||
|||o|h|||3||a|||||
|||r|1|||||t|||||
| | | w | 0 | | | | | m| | | | |
|||a|0||||||||||
|||r|||||||||||
|||d|||||||||||
|||e|||||||||||
|||r|||||||||||
||||||||||||||
+--+--+--+--+--+--+--+--+--+--+--+--+--+--+-0 1 2 3 4 5 6 7 8 9 10…. 15
+--+--+--+--+--+--+--+--+--+--+--+--+--+--+-Select the appropriate slot/card
slot[3]
Since 2Port Eth100 Card is in slot no 3 system has displayed that slot No. Type 3 and Enter
Configure SNMP Network Management[Yes]
Type Yes and press Enter key
The system may also ask you if you want to configure a NMS server, if yes give its IP
address
IP of SNMP Server[aa.bb.cc.dd] :
Say server IP is 192.168.210.200, type 192.168.210.200 and Enter
System will display the following
Node Topology: A connection to NMS via Passport IP Networking.
Media Type : Ethernet
IP Port Address[aa.bb.cc.dd] : 192.168.210.1
IP Netmask(aa.bb.cc.dd) : 255.2255.255.0
IP Broadcast(aa.bb.cc.dd) : 192.168.210.255
Slot No : 3
Card Type : 2 Port Eth100
Port No : eth100/0
Are these values correct? This will activate the provisioning[Yes]:
Type Yes and press Enter key
Start –force prov
…ok
////////////////////////////////////////////////////////////////////////
//////////////////////(Many lines of text)
Check prov
…ok
Startup configuration completed
Please enter "Quit" or select one of the following
1. Reset node to CP only software
2. Create sw lpts and load software on FPs
3. Perform on card tests of each card in the node
4. Configure the node for NMS connectivity
5. Display the cards inserted in the node
6. Provision a spare CP
7. Change the selected NMS connectivity
8. Confirm the provisioning
[5]
>
Type 6 and press Enter key
System will display the following:
You have not confirmed your current provisioning view.
Shall I issue the "Confirm prov" command for you?[Yes]
Type "Yes" and press Enter
System will display the following
Start –force prov
…ok
Spare CP provisioning completed successfully
You may now insert your spare CP in slot No 15
You should now insert the Spare CP in slot No 15 . You will see follwomg on the display
Please enter "Quit" or select one of the following
1. Reset node to CP only software
2. Create sw lpts and load software on FPs
3. Perform on card tests of each card in the node
4. Configure the node for NMS connectivity
5. Display the cards inserted in the node
6. Provision a spare CP
7. Change the selected NMS connectivity
8. Confirm the provisioning
[5]
>
Type 8 and press Enter key
You have not confirmed your current provisioning view.
Shall I issue the "Confirm prov" command for you?[Yes]
Type Yes and press Enter key
Following will be displayed
Start –force prov …. Ok
Confirm prov ……
Prov: 1987-07-16 02:03:51
CLR cleared operator operation condition
/////////////////////////////////////////////////
/////////////////////////////////////////////
////////////////////////////////// (Few lines of text giving states)
Ok
End prov
Confirmation succeeded
Please enter "Quit" or select one of the following
1. Reset node to CP only software
2. Create sw lpts and load software on FPs
3. Perform on card tests of each card in the node
4. Configure the node for NMS connectivity
5. Display the cards inserted in the node
6. Provision a spare CP
7. Change the selected NMS connectivity
8. Confirm the provisioning
[5]
>
Type quit and press Enter key
System will display the following:
You have not confirmed your current provisioning view.
Shall I issue the "Confirm prov" command for you?[Yes]
Type Yes and press Enter key
System will display the following:
Start –force prov
Check prov
..ok
.. ok
Save –f(startup) prov
Commit prov
..ok
..ok
Fs; 1980………
End prov
.. ok
Commit succeeded
Startup facility terminated
Your system has been fully configured with minimum software using startup facility. After
completion of statup utility you can switch on/off the system and when rebooted the login
will be abc and there is no password configured just Enter when password is asked. You wil
see the command prompt as under
>
To enter provisioning mode type following
> start prov
The Committed startup.full.001 file is located in provisioning directory which you can
display using following commands
Prov> cd –p(provisioning) fs
Prov> ls fs
To Create a UserID and give him Access Rights to Configure and Manage a Passport Node:-
For the purpose of understanding let the userID for the Node be "LONDON" and say the
selected password is also "LONDON". We want this userID to be given access to the entire
Passort Network and the capability to debug the configuration. The sequence of command
should be as under:-
Prov> add accesscontrol(ac)
Prov> add ac userid LONDON
Prov> set ac userid LONDON password LONDON
Prov> set ac userid LONDON commandscope network
Prov> set ac userid LONDON commandimpact debug
Prov> set ac userid LONDON allowedaccess local telnet fmip ftp
Prov> set ac userid LONDON allowedoutaccess telnet
Prov> check prov
This may give some error stating that Rtg dpn has been provisioned but RID and MID are
missing. To configure RID and MID use following commands. Let RID=1 and MID=10
Prov> d rtg dpn
System will display
Rtg dpn
Routingid=
Moduleid=
….
…
Prov> set rtg dpn routingid 1
Prov> set rtg dpn moduleid 10
At this stage we can also add the Nodeprefix (26 digits) required for routing. Let nodeprefix
be 399110+20 zeros
Use following command
Prov> set mod nodeprefix 39911000000000000000000000
You can see the nodeprefix using following commands
Prov> d mod
Mod
Nodeprefix 39911000000000000000000000
…………..
…………………
Prov> check prov
Prov> activate prov
Prov> commit prov
Do not commit unless asked to do so. If you commit now the configuration is required to be
saved In a file. If committed, next time you switch on the Passort Node the login will be
"LONDON" and password will also be "LONDON"
To Add Software feature list in the Software LPTs:-
The configuration done so far has added few software LPTs(Logical Processor Types) and
feature list in the software LPTs based on the type of cards present in the chassis and NMS
facility configured. To see the software application version list called avlist use following
command
Prov> d sw avlist
The system will indicate following
Base_CE01S1B
Ip_CE01S1B
The check the LPTs added to software use following command
Prov> d sw lpt/*
The system will display following LPTs along with feature list
Lpt/cp
- Feature list ip
Lpt/ether - ip
Lpt/test - test
There are only three cards of the Passport which are configured to use above LPTs and only
these cards have Logical Processors defined these are CP having LP/0 and lpt/cp, spare CP
having LP/15 and lpt/cp and 2 Port Ethernet Card having LP/3 (Since it in slot No 3) and
lpt/ether. This can be seen using following commands
Prov> d lp/0
It will display
Lp/0
Maincard=sh ca/0
Sparecard=sh ca/15
Logicalprocessortype=sw lpt/cp
If you use the command
Prov>d sh ca/0
It will display
Sh ca/0
Cardtype=cp
Configuredlp=lp/0
Sparingconnection=spare CP
If you use following command to check 2 Port Eth100 card
Which is in slot No 3
Prov>d sh ca/3
It will display
Sh ca/3
Cardtype=2peth100
Configuredlp=lp/3
Sparingconnection= (blank as no sparing is done)
Prov>d lp/3
It will display
Lp/3
Maincard=sh ca/3
Sparecard= (blank)
Logicalprocessortype=sw lpt/ether
If you use the above command for other cards you will find that maincard is mentioned as it
has been recognized by the software but in all other cards lp the sw lpt/test is present because
all the cards have been only tested.
Adding Application Software. Use the following command
Proc> d sw avlist
The system will display all the application version of the software loaded. Since only two
software avlist are loaded so far you will see the display
Base_CE01S1B ip_CE01S1B
Use following commands to add the application software
Prov> set sw avlist networking_CE01S1B vtds_CE01S1B trunks_CE01S1B
framerelay_CE01S1B atmnetworking_CE01S1B wandte_CE01S1B
switchedaccess_CE01S1B aal1ces_CE01S1B
Prov> check prov
Prov> activate prov
Prov> confirm prov
Use commit prov only if you are told to do so
Creating LPTs for use with various Cards:-
First add following feature list to software lpt/cp and lpt/ETHER
Prov> set sw lpt/cp fl oamenet callserver ipifr bgp mvr vncscallserver
Prov> set sw lpt/ether fl ip atmmpe ipcos
Create following software Lpts
If not already created and add featurelist as given below
Prov> add sw lpt/atm
Prov> add sw lpt/e3atm
Prov> add sw lpt/ima
Prov> add sw lpt/voice
Prov> add sw lpt/vnetcas
Prov> add sw lpt/vnetccsqsig
Prov> add sw lpt/vnetccsmcdn
Prov> set sw lpt/atm featurelist atmcore atmtrunks porstrunks atmmpe ip atmuni atmpnni
atmiisp atmaini atmapi porsapi dprsmcsep dprsmcsepintercept frf5endpoint atmspvc
Prov> set sw lpt/e3atm featurelist atmcore atmtrunks porstrunks atmmpe ip atmuni atmpnni
atmiisp atmaini atmapi porsapi dprsmcsep dprsmcsepintercept frf5endpoint
Prov> set sw lpt/ima featurelist ima atmcore atmmpe ip frunialldprs frnnialldprs
fruniipoptimized framerelaydte frsvirtualframer atmuni atmpnni atmiisp atmaini vtds
atmtrunks porstrunks atmapi porsapi dprsmcsagent framerelayatm atmmpespvc ppp
cesreroute atmreroute aal1ces imaatmforum
Prov> swt sw lpt/voice featurelist vtds voice g728 g729 faxrelay tandempassthrough
Prov> swt sw lpt/vnetcas featurelist voicenetworking cassig g728 g729 faxrelay
tandempassthrough
Prov> swt sw lpt/vnetmcdn featurelist voicenetworking mcdnsig g728 g729 faxrelay
tandempassthrough
Prov> swt sw lpt/vnetqsig featurelist voicenetworking etsiqsig g728 g729 faxrelay
tandempassthrough
Prov> check prov
Prov> activate prov
Prov> confirm prov
Use commit prov only if you are told to do so
Now there is a need to add logical processors with the cards and set software LPTs which the
card will use. Let us assume the cards in various slots are as under
Slot No 0
- CP Card
Slot No 1
- 1 Port MVPE1 Card
Slot No 2
- ILS Forwarder Card
Slot No 3
- 2 Port Ethernet Card
Slot No 4
- OC3 Ports of 32 Port E1 MSA
Slot No 5
- 32 Port E1 MSA Card
Slot No 6
- Empty
Slot No 7
- Empty
Slot No 8
- 2 Port OC3 Card ATM IP
Slot No 9
- Empty
Slot No 10 - Empty
Slot No 11
- empty
Slot No 12 - 3 Port E3 ATM IP Card
Slot No 13 - Empty
Slot No 14 - Empty
Slot No 15 - Spare CP
Before proceeding adhead check each card whether a Logical Processor (lp) and a Logical
Processor Type (Lpt) is already configured or not. Use following commands
Prov> d sh ca/3
It will display
Sh ca/3
Cardtype =2peth100
Configuredlp =lp/3
Sparingconnection=
Prov> lp/3
Lp/3
Maincard=sh ca/3
Sparecard=
Logicalprocessortype=sw lpt/ether
Suppose a card does not have LP and Logical Processor Type mentioned when you use above
commands then these need to be configured. Two examples given below are for configuring
lp and lpt for 3 Port E3 ATM IP (Card in slot No 12) and 32 Port E1 MSA Cards(Card in slot
No5)
Prov> add lp/12
Prov> set lp/12 maincard sh ca/12
Prov> set lp/12 logicalprocessortype sw lpt/e3atm
Prov> add lp/5
Prov> set lp/5 maincard sh ca/5
Prov> set lp/5 logicalprocessortype sw lpt/ima
Once you have done above configuration using display commands the system will display as
under
Prov> d lp/5
Lp/5
Maincard=sh ca/5
Sparecard=
Logicalprocessortype=sw lpt/ima
Prov> d lp/12
Lp/12
Maincard=sh ca/12
Sparecard=
Logicalprocessortype=sw lpt/e3atm
Prov> d sh ca/5
Sh ca/5
Cardtype =32pe1msa
Configuredlp =lp/5
Sparingconnection=
Prov> d sh ca/12
Sh ca/12
Cardtype =3pe3atm
Configuredlp =lp/12
Sparingconnection=
In similar way configure all the Logical Processors and Logical Processor Types for the
cards.
Once completed use following command
Prov> check prov
Prov> activate prov
Prov> confirm prov
Use commit prov only if you are told to do so
Now the node is ready for further configuration of various services like ATM, FrameRelay,
HTDS, IP Voice etc
Posted 19th February 2010 by Aryan
2
View comments
1.
fadyAugust 21, 2010 at 3:28 AM
excuse me for the newbie question, but what is a passport ? and the difference
between it and the switch ?
Reply
2.
harikrishnan gowderSeptember 23, 2012 at 3:05 AM
excuse me about this question. Anybody tell me, how can see the raw data (traps)that
passport provide for management and what's the command to view the same.
Reply
Nortel Passport 7480 , JUNIPER & CISCO







Classic
Flipcard
Magazine
Mosaic
Sidebar
Snapshot
Timeslide
1.
Jul
25
Online Lab For Cisco , Juniper ,
VMware, Cisco NEXUX, Linux
Debian64 & Radware Alteon
Online LAB for those who don't have any simulator in there PC by any reason try
this link .
http://www.sharontools.com
http://www.sharontools.com/images/lab.jpg
If you have secure CRT then its very easy to use
See the Screen Sjot may be it will help you
Posted 25th July by Aryan
0
Add a comment
2.
Mar
9
INSTALLATION OF JUNIPER
"OLIVE" IN VMWARE
Make sure you have below ready for installation:
1. VMWare Workstation.
2. Download Free BSD from here. For 9.x Junos you can use
4.11 miniinst.iso which works fine
3. Make sure you have a copy of JUNOS.
4. Download Filezilla from here.
I’ve copied screenshots here for JUNOS installation,
Vmware workstation 8 and Free BSD 4.11 is being used her.
Customize hardware settings here, you can lower RAM
after installation
You can select first option here and continue
installation,
At the "SysInstall Main Menu" choose "Express - Begin a
quick installation (for the impatient)"
At the FDISK Parition Editor type A to use Entire Disk,
then type Q to finish
For the "Boot Manager" choose "Standard - Install a
standard MBR (no boot manager)"For the "Disklabel
Editor":
Step 1 of 4: Type C to create, then delete the values and insert 500M , then choose FS
(File System), then type /
Step 2 of 4: Type C, delete values, insert 500M , then choose Swap space
Step 3 of 4: Type C, delete values, insert 100M , choose FS, type /config
Step 4 of 4: Type C, accept the values presented with an , choose FS, type /var
Type Q to finish
For "Choose Distributions" choose "Exit this menu - returning to previous" (i.e. no
need to install any extras)
For "Choose installation media" choose "CD/DVD"
At the "User Confirmation Requested" where it asks if you want to proceed with the
install, choose "Yes" - Lots of install stuff will now happen
At the window where it gives you an opportunity to "Visit the general config menu
for a chance to set any last options", choose "Yes"
Using the cursor keys, choose "Root password" and enter twice a new 'root' password
Using the cursor keys, choose "Interfaces", then choose "em0", for IPv6 choose "no",
for dhcp choose "yes", for host put in a dummy name like "olive" then scroll down to
"OK" (using DHCP will give you an IP address, allowing you to FTP jinstall images
to your Olive machine. If you do not have a DHCP server on your bridged LAN
segment, then configure a static IP and default gateway as appropriate)
Then choose "Exit", then choose "Exit install" from the SysInstall main menu
A final confirmation will ask if you want to reboot, choose "Yes"
Installing JUNOS
At this point, you should have a running FreeBSD virtual machine, which can receive
files by FTP from an FTP server that you are hosting a "jinstall" JUNOS image on
(which is lower than version 7.4).
Do the following (logged in as root):
cd /var/tmp
ftp e.g. ftp 192.168.1.251
username: anonymous
password: a@b.c
binary
get e.g. get jinstall-5.7R2.4-domestic-signed.tgz
bye
Check file is received:
ls -al
rm /dev/wd0c
ln -s /dev/ad0c /dev/wd0c
mkdir /var/etc
touch /var/etc
touch /var/etc/master.passwd
touch /var/etc/inetd.conf
touch /var/etc/group
pkg_add /var/tmp/jinstall-5.7R2.4-domestic-signed.tgz
shutdown -r now
NOTE: at this point, if you loaded a JUNOS version of
below 7.4, then when you reload - you will lose the
ability to use any of the virtual NIC cards in this
virtual machine
When the virtual machine reboots, you may lose access to
the CLI dependant on which version you loaded. With a
version 5 image, you will still have access, with a
higher version, you lose access. The following two
sections discuss accessing the virtual machine through
the serial port, and then the section following those
discusses upgrading the JUNOS version to one higher than
7.4 so the "e1000" virtual NICs can be detected and
utilised.
Posted 9th March by Aryan
1
View comments
3.
Mar
9
Posted 9th March by Aryan
0
Add a comment
4.
Jun
21
CONFIGURATION IP OVER ATM ON
MSA E1/0 CH/0 TS 1 TO 4& IP
OPTIMIZED DLCI OVER FR (PVC,
SPVC & SVC)ON MSA E1/0 CH/1 TS 5
TO 8
Configuration on Passport No 1
Add lp/5 e1/0 (Channel/0 will be automatically added)
add lp/5 e1/0 ch/0 atmcell
set lp/5 e1/0 ch/0 timeslots 1 2 3 4
add lp/5 e1/0 ch/1
set lp/5 e1/0 ch/1 timeslots 5 6 7 8
add lp/10 eth100/0
add lp/10 eth100/1
add la/1 (if not already added, framer will be added automatically)
set la/1 framer interfacename lp/10 eth100/0
add la/2 (framer will be automatically added)
set la/2 framer interfacename lp/10 eth100/1
***** vr/0 router must be already existing since it was created during stratup
procedure
add vr/0 (It will be already present)
set vr/0 vrp lp/0 (It will already be there)
add vr/0 ip (if already not added)
add vr/0 ip rip (if already not added)
add vr/0 pp/eth0
set vr/0 pp/eth0 linktomedia la/1
add vr/0 pp/eth0 ipp
add vr/0 pp/eth0 ipp logicalif/192.168.210.1
set vr/0 pp/eth/0 ipp log/192.168.210.1 netmask 255.255.255.0
set vr/0 pp/eth0 ipp log/192.168.210.1 broadcast 192.168.210.255
add vr/0 pp/waneth012
add vr/0 pp/waneth012 ipp
add vr/0 pp/waneth012 ipp log/192.168.1.1
add vr/0 pp/waneth012 ipp log/192.168.1.1 ripif
set vr/0 pp/waneth012 ipp log/192.168.1.1 netmask 255.255.255.252
set vr/0 pp/waneth012 ipp log/192.168.1.1 linktomediaconnection atmmpe/50 ac/1
(Not essential
**** add a new virtual router
add vr/1
set vr/1 vrp lp/0
add vr/1 ip
add vr/1 ip rip
add vr/1 pp/eth1
set vr/1 pp/eth1 linktomedia la/2
add vr/1 pp/eth1 ipp
add vr/1 pp/eth1 ipp logicalif/192.168.100.1
set vr/1 pp/eth/1 ipp log/192.168.100.1 netmask 255.255.255.192
set vr/1 pp/eth1 ipp log/192.168.100.1 broadcast 192.168.100.63
add vr/1 pp/waneth112
add vr/1 pp/waneth112 ipp
add vr/1 pp/waneth112 ipp log/192.168.1.5
add vr/1 pp/waneth112 ipp log/192.168.1.5 ripif
set vr/1 pp/waneth112 ipp log/192.168.1.5 netmask 255.255.255.252
***Commands deleted below are not required for this configuration but next two lines
are ****needed
set vr/1 pp/waneth112 ipp log/192.168.1.5 linktomediaconnection frdte/1 stdlci/100
@
@ This command will work only when frdte/1 and stdlci/100 has been added
set vr/1 pp/waneth112 ipp log/192.168.1.5 linktomediaconnection ipdlcigrp/1 frc/1 @
@ This command will work only when ipdlcigrp/1 has been added
****Adding a atmif and atmmpe
add atmif/50 (ca will be automatically added)
set atmif/50 interfacename lp/5 e1/0 ch/0
set atmif/50 ca minautoselectedvciforvpizero 200
add atmif/50 vcc/0.40 (vcd and tm will be added automatically)
add atmif/50 vcc/0.40 nep
set atmif/50 vcc/0.40 vcd tm txtdt 3
set atmif/50 vcc/0.40 vcd tm txtdp 1 1000
add atmmpe/50 (ac/1 will be added automatically)
set atmmpe/50 linktoprotocolport vr/0 pp/waneth012
set atmmpe/50 ac/1 atmconnection atmif/50 vcc/0.40 nep
set atmmpe/50 ac/1 linktoipinterface vr/0 pp/waneth012 ipp log/192.168.1.1 (not
essential)
**** For configuring IP Optimized DLCI frdte/1 and fruni/1 are not required and new
*****+component called ipdlcigroup had to be added
add ipdlcigrp/1 (this will add frc/1 automatically)
***** It is ipdlcigrp/1 which will be associated with vr/1 pp/waneth112 and
ipdlcigrp/1 frc/1
*****which will be associated with vr/1 pp/waneth112 ipp log/192.168.1.5
*****linktomediaconnection (Note under configuration of vr/1)
set ipdlcigrp/1 linktoprotocolport vr/1 pp/waneth112
****Commands deleted below are not required for IP Optimized DLCI
****Adding a frdte, fruni for Frame Relay Connection on e1/0 ch/1
add frdte/1 (framer, lmi and rg/1 will be added automatically)
delete frdte/1 framer
add frdte/1 vframer
set frdte/1 vframer logicalprocessor(lp) lp/5
add frdte/1 stdlci/100
set frdte/1 rg/1 linktofrdtedlci frdte/1 stdlci/100
set frdte/1 rg/1 linktoprotocolport vr/1 pp/waneth112
set frdte/1 lmi procedures none
***** Adding a fruni/1
add fruni/1 (framer, dna, lmi etc will be added automatically)
delete fruni/1 framer
add fruni/1 vframer
set fruni/1 vframer logicalprocessor(lp) lp/5
set fruni/1 vframer othervirtualframer (ovf) frdte/1 vframer
*******The above command will work only if vframer under frdte/1 has been added)
set fruni/1 dna dna 302191111033 (DNA of fruni/1)
set fruni/1 lmi procedures none
set fruni/1 lmi side network
add fruni/1 dlci/100
*****(dc will be added automatically, DLCI for comn with fruni/2)
set fruni/1 dlci/100 dc rdna 302191111034
*****(Remote DNA of fruni/2 for comn from fruni/1 to 2)
set fruni/1 dlci/100 dc rdlci 100
set fruni/1 dlci/100 dc type permanentmaster (default value, need not use this
command)
****(permanenetslave(fruni/2) will communicate with permanentmaster (fruni/1))
****Adding a Fruni/2
add fruni/2 (framer, lmi, dna etc will be added automatically)
set fruni/2 framer interfacename lp/5 e1/0 ch/1
set fruni/2 dna dna 302191111034 (DNA of fruni/2)
set fruni/2 lmi procedures itu
set fruni/2 lmi side both
****Commands deleted below are not required for IP Optimized DLCI
add fruni/2 dlci/100
*****(dc will be added automatically, DLCI for comn with fruni/1)
*****For IP Optimized DLCI dc should be deleted and ipconnection is added
delete fruni/2 dlci/100 dc
add fruni/2 dlci/100 ipconnection
set fruni/2 dlci/100 ipconnection linktoipdlcigroup ipdlcigrp/1 frc/1
set fruni/2 dlci/100 dc rdna 302191111033
*****(Remote DNA of fruni/1 for comn from fruni/2 to 1)
set fruni/2 dlci/100 dc rdlci 100
set fruni/2 dlci/100 dc type permanentslave
****(permanenetslave(fruni/2) will communicate with permanentmaster (fruni/1))
add fruni/2 dlci/16 (dc will be added automatically)
set fruni/2 dlci/16 dc rdna 302191332034
####
####
*****(Remote DNA of destination node fruni/2)
####
set fruni/2 dlci/16 dc rdlci 17
####
*****(Remote DLCI of destination node fruni/2)
set fruni/2 dlci/16 dc type permanentmaster (default value, need not be configured)
####
****(permanenetslave(fruni/2 of destination
permanentmaster (fruni/2 of this node))
node)
will
communicate
with
*******Adding Node parameters
set module routingid(rid) 1 (if not existing)
set module moduleid 10 (if not existing)
add module vcs
set module vcs networkidcode 3021 (Used in all DNA addresses)
add module frs (if not existing)
*** Adding Call Server ie Call Router which contains table of DNA addresses
associated with RID and MID
*** Command deleted below are not required for IP DLCI Optimized configuration
however, ****even if these are not deleted, it will affect the services engineered
add cr
*** Call Router is added
add cr npi/x121
***Network Plan Indicator (NPI) is added to use X.121 format of addressing used by
DPRS
add cr npi/x121 dna/302191
*****Prefix of DNA is added which is for Region 1 ie RID=1
set cr npi/x121 dna/302191 routingid 1
add cr npi/x121 dna/302191111033
***DNA of fruni/1 on this node which has moduleid=10
set cr npi/x121 dna/302191111033 moduleid 10
add cr npi/x121 dna/302191111034
***DNA of fruni/2 on this node which has moduleid=10
set cr npi/x121 dna/302191111034 moduleid 10
add cr npi/x121 dna/302191332033
***DNA of fruni/1 on destination node which has moduleid=20
set cr npi/x121 dna/302191332033 moduleid 20
add cr npi/x121 dna/302191332034
***DNA of fruni/2 on destination node which has moduleid=20
set cr npi/x121 dna/302191332034 moduleid 20
******Configuration complete check it, activate it and confirm it
check prov
act prov
confirm prov
The above configuration is for engineering of PVC connection. If SPVC connection is
required to be configured, signaling (Sig) has to be added under fruni/2
add fruni/2 sig
check prov
act prov
confirm prov
If the configuration is required for SVC then in addition to above command of adding
sig, command lines marked as #### should be deleted. Once deleted use check prov,
act prov and confirm prov to activate the configuration
Note;- Do Not Commit the provisioning
Configuration on Passport No 2
Add lp/4 e1/0 (Channel/0 will be automatically added)
add lp/4 e1/0 ch/0 atmcell
set lp/4 e1/0 ch/0 timeslots 1 2 3 4
add lp/4 e1/0 ch/1
set lp/4 e1/0 ch/1 timeslots 5 6 7 8
add lp/3 eth100/0
add lp/3 eth100/1
add la/1 (if not already added, framer will be added automatically)
set la/1 framer interfacename lp/3 eth100/0
add la/2 (framer will be automatically added)
set la/2 framer interfacename lp/3 eth100/1
***** vr/0 router must be already existing since it was created during stratup
procedure
add vr/0 (It will be already present)
set vr/0 vrp lp/0 (It will already be there)
add vr/0 ip (if already not added)
add vr/0 ip rip (if already not added)
add vr/0 pp/eth0
set vr/0 pp/eth0 linktomedia la/1
add vr/0 pp/eth0 ipp
add vr/0 pp/eth0 ipp logicalif/192.168.220.1
set vr/0 pp/eth/0 ipp log/192.168.220.1 netmask 255.255.255.0
set vr/0 pp/eth0 ipp log/192.168.220.1 broadcast 192.168.220.255
add vr/0 pp/waneth021
add vr/0 pp/waneth021 ipp
add vr/0 pp/waneth021 ipp log/192.168.1.2
add vr/0 pp/waneth021 ipp log/192.168.1.2 ripif
set vr/0 pp/waneth021 ipp log/192.168.1.2 netmask 255.255.255.252
set vr/0 pp/waneth021 ipp log/192.168.1.2 linktomediaconnection atmmpe/40 ac/1
(Not essential
**** add a new virtual router
add vr/1
set vr/1 vrp lp/0
add vr/1 ip
add vr/1 ip rip
add vr/1 pp/eth1
set vr/1 pp/eth1 linktomedia la/2
add vr/1 pp/eth1 ipp
add vr/1 pp/eth1 ipp logicalif/192.168.100.65
set vr/1 pp/eth/1 ipp log/192.168.100.65 netmask 255.255.255.192
set vr/1 pp/eth1 ipp log/192.168.100.65 broadcast 192.168.100.127
add vr/1 pp/waneth121
add vr/1 pp/waneth121 ipp
add vr/1 pp/waneth121 ipp log/192.168.1.6
add vr/1 pp/waneth121 ipp log/192.168.1.6 ripif
set vr/1 pp/waneth121 ipp log/192.168.1.6 netmask 255.255.255.252
***Commands deleted below are not required for this configuration but next two lines
are ****needed
set vr/1 pp/waneth121 ipp log/192.168.1.6 linktomediaconnection frdte/1 stdlci/100
@
@ This command will work only when frdte/1 and stdlci/100 has been added
set vr/1 pp/waneth121 ipp log/192.168.1.6 linktomediaconnection ipdlcigrp/1 frc/1 @
@ This command will work only when ipdlcigrp/1 has been added
****Adding a atmif and atmmpe
add atmif/40 (ca will be automatically added)
set atmif/40 interfacename lp/4 e1/0 ch/0
set atmif/40 ca minautoselectedvciforvpizero 200
add atmif/40 vcc/0.40 (vcd and tm will be added automatically)
add atmif/40 vcc/0.40 nep
set atmif/40 vcc/0.40 vcd tm txtdt 3
set atmif/40 vcc/0.40 vcd tm txtdp 1 1000
add atmmpe/40 (ac/1 will be added automatically)
set atmmpe/40 linktoprotocolport vr/0 pp/waneth021
set atmmpe/40 ac/1 atmconnection atmif/40 vcc/0.40 nep
set atmmpe/40 ac/1 linktoipinterface vr/0 pp/waneth021 ipp log/192.168.1.2 (not
essential)
**** For configuring IP Optimized DLCI frdte/1 and fruni/1 are not required and new
*****+component called ipdlcigroup had to be added
add ipdlcigrp/1 (this will add frc/1 automatically)
***** It is ipdlcigrp/1 which will be associated with vr/1 pp/waneth121 and
ipdlcigrp/1 frc/1
*****which will be associated with vr/1 pp/waneth121 ipp log/192.168.1.6
*****linktomediaconnection (Note under configuration of vr/1)
set ipdlcigrp/1 linktoprotocolport vr/1 pp/waneth121
****Commands deleted below are not required for IP Optimized DLCI
****Adding a frdte, fruni for Frame Relay Connection on e1/0 ch/1
add frdte/1 (framer, lmi and rg/1 will be added automatically)
delete frdte/1 framer
add frdte/1 vframer
set frdte/1 vframer logicalprocessor(lp) lp/4
add frdte/1 stdlci/100
set frdte/1 rg/1 linktofrdtedlci frdte/1 stdlci/100
set frdte/1 rg/1 linktoprotocolport vr/1 pp/waneth121
set frdte/1 lmi procedures none
***** Adding a fruni/1
add fruni/1 (framer, dna, lmi etc will be added automatically)
delete fruni/1 framer
add fruni/1 vframer
set fruni/1 vframer logicalprocessor(lp) lp/4
set fruni/1 vframer othervirtualframer (ovf) frdte/1 vframer
*******The above command will work only if vframer under frdte/1 has been added)
set fruni/1 dna dna 302191332033 (DNA of fruni/1)
set fruni/1 lmi procedures none
set fruni/1 lmi side network
add fruni/1 dlci/100
*****(dc will be added automatically, DLCI for comn with fruni/2)
set fruni/1 dlci/100 dc rdna 302191332034
*****(Remote DNA of fruni/2 for comn from fruni/1 to 2)
set fruni/1 dlci/100 dc rdlci 100
set fruni/1 dlci/100 dc type permanentmaster (default value, need not use this
command)
****(permanenetslave(fruni/2) will communicate with permanentmaster (fruni/1))
****Adding a Fruni/2
add fruni/2 (framer, lmi, dna etc will be added automatically)
set fruni/2 framer interfacename lp/4 e1/0 ch/1
set fruni/2 dna dna 302191332034 (DNA of fruni/2)
set fruni/2 lmi procedures itu
set fruni/2 lmi side both
****Commands deleted below are not required for IP Optimized DLCI
add fruni/2 dlci/100
*****(dc will be added automatically, DLCI for comn with fruni/1)
*****For IP Optimized DLCI dc should be deleted and ipconnection is added
delete fruni/2 dlci/100 dc
add fruni/2 dlci/100 ipconnection
set fruni/2 dlci/100 ipconnection linktoipdlcigroup ipdlcigrp/1 frc/1
set fruni/2 dlci/100 dc rdna 302191332033
*****(Remote DNA of fruni/1 for comn from fruni/2 to 1)
set fruni/2 dlci/100 dc rdlci 100
set fruni/2 dlci/100 dc type permanentslave
****(permanenetslave(fruni/2) will communicate with permanentmaster (fruni/1))
add fruni/2 dlci/17 (dc will be added automatically)
set fruni/2 dlci/17 dc rdna 302191111034
####
*****(Remote DNA of destination node fruni/2)
set fruni/2 dlci/17 dc rdlci 16
####
####
####
*****(Remote DLCI of destination node fruni/2)
####
set fruni/2 dlci/17 dc type permanentslave
****(permanenetslave(fruni/2 of this node) will communicate with permanentmaster
(fruni/2 of destination node))
*******Adding Node parameters
set module routingid(rid) 1 (if not existing)
set module moduleid 20 (if not existing)
add module vcs
set module vcs networkidcode 3021 (Used in all DNA addresses)
add module frs (if not existing)
*** Adding Call Server ie Call Router which contains table of DNA addresses
associated with RID and MID
*** Command deleted below are not required for IP DLCI Optimized configuration
however, ****even if these are not deleted, it will affect the services engineered
add cr
*** Call Router is added
add cr npi/x121
***Network Plan Indicator (NPI) is added to use X.121 format of addressing used by
DPRS
add cr npi/x121 dna/302191
*****Prefix of DNA is added which is for Region 1 ie RID=1
set cr npi/x121 dna/302191 routingid 1
add cr npi/x121 dna/302191111033
***DNA of fruni/1 on this node which has moduleid=10
set cr npi/x121 dna/302191111033 moduleid 10
add npi/x121 dna/302191111034
***DNA of fruni/2 on this node which has moduleid=10
set cr npi/x121 dna/302191111034 moduleid 10
add cr npi/x121 dna/302191332033
***DNA of fruni/1 on destination node which has moduleid=20
set cr npi/x121 dna/302191332033 moduleid 20
add cr npi/x121 dna/302191332034
***DNA of fruni/2 on destination node which has moduleid=20
set cr npi/x121 dna/302191332034 moduleid 20
******Configuration complete check it, activate it and confirm it
check prov
act prov
confirm prov
The above configuration is for engineering of PVC connection. If SPVC connection is
required to be configured, signaling (Sig) has to be added under fruni/2
add fruni/2 sig
check prov
act prov
confirm prov
If the configuration is required for SVC then in addition to above command of adding
sig, command lines marked as #### should be deleted. Once deleted use check prov,
act prov and confirm prov to activate the configuration
Note;- Do Not Commit the provisioning
Posted 21st June 2010 by Aryan
0
Add a comment
5.
Jun
21
CONFIGURATION IP OVER ATM ON
MSA E1/0 CH/0 TS 1 TO 4& IP OVER
FR (SVC)ON MSA E1/0 CH/1 TS 5 TO
8
Configuration on Passport No 1
Add lp/5 e1/0 (Channel/0 will be automatically added)
add lp/5 e1/0 ch/0 atmcell
set lp/5 e1/0 ch/0 timeslots 1 2 3 4
add lp/5 e1/0 ch/1
set lp/5 e1/0 ch/1 timeslots 5 6 7 8
add lp/10 eth100/0
add lp/10 eth100/1
add la/1 (if not already added, framer will be added automatically)
set la/1 framer interfacename lp/10 eth100/0
add la/2 (framer will be automatically added)
set la/2 framer interfacename lp/10 eth100/1
***** vr/0 router must be already existing since it was created during
stratup procedure
add vr/0 (It will be already present)
set vr/0 vrp lp/0 (It will already be there)
add vr/0 ip (if already not added)
add vr/0 ip rip (if already not added)
add vr/0 pp/eth0
set vr/0 pp/eth0 linktomedia la/1
add vr/0 pp/eth0 ipp
add vr/0 pp/eth0 ipp logicalif/192.168.210.1
set vr/0 pp/eth/0 ipp log/192.168.210.1 netmask 255.255.255.0
set vr/0 pp/eth0 ipp log/192.168.210.1 broadcast 192.168.210.255
add vr/0 pp/waneth012
add vr/0 pp/waneth012 ipp
add vr/0 pp/waneth012 ipp log/192.168.1.1
add vr/0 pp/waneth012 ipp log/192.168.1.1 ripif
set
vr/0
pp/waneth012
255.255.255.252
ipp
log/192.168.1.1
netmask
set vr/0 pp/waneth012 ipp log/192.168.1.1 linktomediaconnection
atmmpe/50 ac/1 (Not essential
**** add a new virtual router
add vr/1
set vr/1 vrp lp/0
add vr/1 ip
add vr/1 ip rip
add vr/1 pp/eth1
set vr/1 pp/eth1 linktomedia la/2
add vr/1 pp/eth1 ipp
add vr/1 pp/eth1 ipp logicalif/192.168.100.1
set vr/1 pp/eth/1 ipp log/192.168.100.1 netmask 255.255.255.192
set vr/1 pp/eth1 ipp log/192.168.100.1 broadcast 192.168.100.63
add vr/1 pp/waneth112
add vr/1 pp/waneth112 ipp
add vr/1 pp/waneth112 ipp log/192.168.1.5
add vr/1 pp/waneth112 ipp log/192.168.1.5 ripif
set
vr/1
pp/waneth112
255.255.255.252
ipp
log/192.168.1.5
netmask
set vr/1 pp/waneth112 ipp log/192.168.1.5 linktomediaconnection
frdte/1 stdlci/100 @
@ This command will work only when frdte/1 and stdlci/100 has been
added
****Adding a atmif and atmmpe
add atmif/50 (ca will be automatically added)
set atmif/50 interfacename lp/5 e1/0 ch/0
set atmif/50 ca minautoselectedvciforvpizero 200
add atmif/50 vcc/0.40 (vcd and tm will be added automatically)
add atmif/50 vcc/0.40 nep
set atmif/50 vcc/0.40 vcd tm txtdt 3
set atmif/50 vcc/0.40 vcd tm txtdp 1 1000
add atmmpe/50 (ac/1 will be added automatically)
set atmmpe/50 linktoprotocolport vr/0 pp/waneth012
set atmmpe/50 ac/1 atmconnection atmif/50 vcc/0.40 nep
set atmmpe/50 ac/1 linktoipinterface
log/192.168.1.1 (not essential)
vr/0
pp/waneth012
ipp
****Adding a frdte, fruni for Frame Relay Connection on e1/0 ch/1
add frdte/1 (framer, lmi and rg/1 will be added automatically)
delete frdte/1 framer
add frdte/1 vframer
set frdte/1 vframer logicalprocessor(lp) lp/5
add frdte/1 stdlci/100
set frdte/1 rg/1 linktofrdtedlci frdte/1 stdlci/100
set frdte/1 rg/1 linktoprotocolport vr/1 pp/waneth112
set frdte/1 lmi procedures none
***** Adding a fruni/1
add fruni/1 (framer, dna, lmi etc will be added automatically)
delete fruni/1 framer
add fruni/1 vframer
set fruni/1 vframer logicalprocessor(lp) lp/5
set fruni/1 vframer othervirtualframer (ovf) frdte/1 vframer
*******The above command will work only if vframer under frdte/1 has
been added)
set fruni/1 dna dna 302191111033 (DNA of fruni/1)
set fruni/1 lmi procedures none
set fruni/1 lmi side network
add fruni/1 dlci/100
*****(dc will be added automatically, DLCI for comn with fruni/2)
set fruni/1 dlci/100 dc rdna 302191111034
*****(Remote DNA of fruni/2 for comn from fruni/1 to 2)
set fruni/1 dlci/100 dc rdlci 100
set fruni/1 dlci/100 dc type permanentmaster (default value, need not
use this command)
****(permanenetslave(fruni/2)
permanentmaster (fruni/1))
will
communicate
with
****Adding a Fruni/2
add fruni/2 (framer, lmi, dna etc will be added automatically)
set fruni/2 framer interfacename lp/5 e1/0 ch/1
set fruni/2 dna dna 302191111034 (DNA of fruni/2)
set fruni/2 lmi procedures itu
set fruni/2 lmi side both
add fruni/2 dlci/100
*****(dc will be added automatically, DLCI for comn with fruni/1)
set fruni/2 dlci/100 dc rdna 302191111033
*****(Remote DNA of fruni/1 for comn from fruni/2 to 1)
set fruni/2 dlci/100 dc rdlci 100
set fruni/2 dlci/100 dc type permanentslave
****(permanenetslave(fruni/2)
permanentmaster (fruni/1))
will
communicate
****Add sig on fruni/2 for configuring SVC connectivity
add fruni/2 sig
with
****command which are deleted below are not required for SVC
configuration
add fruni/2 dlci/16 (dc will be added automatically)
set fruni/2 dlci/16 dc rdna 302191332034
*****(Remote DNA of destination node fruni/2)
set fruni/2 dlci/16 dc rdlci 17
*****(Remote DLCI of destination node fruni/2)
set fruni/2 dlci/16 dc type permanentmaster (default value, need not
be configured)
****(permanenetslave(fruni/2 of destination node) will communicate
with permanentmaster (fruni/2 of this node))
*******Adding Node parameters
set module routingid(rid) 1 (if not existing)
set module moduleid 10 (if not existing)
add module vcs
set module vcs networkidcode 3021 (Used in all DNA addresses)
add module frs (if not existing)
*** Adding Call Server ie Call Router which contains table of DNA
addresses associated with RID and MID
add cr
*** Call Router is added
add cr npi/x121
***Network Plan Indicator (NPI) is added to use X.121 format of
addressing used by DPRS
add cr npi/x121 dna/302191
*****Prefix of DNA is added which is for Region 1 ie RID=1
set cr npi/x121 dna/302191 routingid 1
add cr npi/x121 dna/302191111033
***DNA of fruni/1 on this node which has moduleid=10
set cr npi/x121 dna/302191111033 moduleid 10
add cr npi/x121 dna/302191111034
***DNA of fruni/2 on this node which has moduleid=10
set cr npi/x121 dna/302191111034 moduleid 10
add cr npi/x121 dna/302191332033
***DNA of fruni/1 on destination node which has moduleid=20
set cr npi/x121 dna/302191332033 moduleid 20
add cr npi/x121 dna/302191332034
***DNA of fruni/2 on destination node which has moduleid=20
set cr npi/x121 dna/302191332034 moduleid 20
******Configuration complete check it, activate it and confirm it
check prov
act prov
confirm prov
Note;- Do Not Commit the provisioning
Configuration on Passport No 2
Add lp/4 e1/0 (Channel/0 will be automatically added)
add lp/4 e1/0 ch/0 atmcell
set lp/4 e1/0 ch/0 timeslots 1 2 3 4
add lp/4 e1/0 ch/1
set lp/4 e1/0 ch/1 timeslots 5 6 7 8
add lp/3 eth100/0
add lp/3 eth100/1
add la/1 (if not already added, framer will be added automatically)
set la/1 framer interfacename lp/3 eth100/0
add la/2 (framer will be automatically added)
set la/2 framer interfacename lp/3 eth100/1
***** vr/0 router must be already existing since it was created during
stratup procedure
add vr/0 (It will be already present)
set vr/0 vrp lp/0 (It will already be there)
add vr/0 ip (if already not added)
add vr/0 ip rip (if already not added)
add vr/0 pp/eth0
set vr/0 pp/eth0 linktomedia la/1
add vr/0 pp/eth0 ipp
add vr/0 pp/eth0 ipp logicalif/192.168.220.1
set vr/0 pp/eth/0 ipp log/192.168.220.1 netmask 255.255.255.0
set vr/0 pp/eth0 ipp log/192.168.220.1 broadcast 192.168.220.255
add vr/0 pp/waneth021
add vr/0 pp/waneth021 ipp
add vr/0 pp/waneth021 ipp log/192.168.1.2
add vr/0 pp/waneth021 ipp log/192.168.1.2 ripif
set
vr/0
pp/waneth021
255.255.255.252
ipp
log/192.168.1.2
netmask
set vr/0 pp/waneth021 ipp log/192.168.1.2 linktomediaconnection
atmmpe/40 ac/1 (Not essential
**** add a new virtual router
add vr/1
set vr/1 vrp lp/0
add vr/1 ip
add vr/1 ip rip
add vr/1 pp/eth1
set vr/1 pp/eth1 linktomedia la/2
add vr/1 pp/eth1 ipp
add vr/1 pp/eth1 ipp logicalif/192.168.100.65
set vr/1 pp/eth/1 ipp log/192.168.100.65 netmask 255.255.255.192
set vr/1 pp/eth1 ipp log/192.168.100.65 broadcast 192.168.100.127
add vr/1 pp/waneth121
add vr/1 pp/waneth121 ipp
add vr/1 pp/waneth121 ipp log/192.168.1.6
add vr/1 pp/waneth121 ipp log/192.168.1.6 ripif
set
vr/1
pp/waneth121
255.255.255.252
ipp
log/192.168.1.6
netmask
set vr/1 pp/waneth121 ipp log/192.168.1.6 linktomediaconnection
frdte/1 stdlci/100 @
@ This command will work only when frdte/1 and stdlci/100 has been
added
****Adding a atmif and atmmpe
add atmif/40 (ca will be automatically added)
set atmif/40 interfacename lp/4 e1/0 ch/0
set atmif/40 ca minautoselectedvciforvpizero 200
add atmif/40 vcc/0.40 (vcd and tm will be added automatically)
add atmif/40 vcc/0.40 nep
set atmif/40 vcc/0.40 vcd tm txtdt 3
set atmif/40 vcc/0.40 vcd tm txtdp 1 1000
add atmmpe/40 (ac/1 will be added automatically)
set atmmpe/40 linktoprotocolport vr/0 pp/waneth021
set atmmpe/40 ac/1 atmconnection atmif/40 vcc/0.40 nep
set atmmpe/40 ac/1 linktoipinterface
log/192.168.1.2 (not essential)
vr/0
pp/waneth021
****Adding a frdte, fruni for Frame Relay Connection on e1/0 ch/1
add frdte/1 (framer, lmi and rg/1 will be added automatically)
delete frdte/1 framer
add frdte/1 vframer
set frdte/1 vframer logicalprocessor(lp) lp/4
ipp
add frdte/1 stdlci/100
set frdte/1 rg/1 linktofrdtedlci frdte/1 stdlci/100
set frdte/1 rg/1 linktoprotocolport vr/1 pp/waneth121
set frdte/1 lmi procedures none
***** Adding a fruni/1
add fruni/1 (framer, dna, lmi etc will be added automatically)
delete fruni/1 framer
add fruni/1 vframer
set fruni/1 vframer logicalprocessor(lp) lp/4
set fruni/1 vframer othervirtualframer (ovf) frdte/1 vframer
*******The above command will work only if vframer under frdte/1 has
been added)
set fruni/1 dna dna 302191332033 (DNA of fruni/1)
set fruni/1 lmi procedures none
set fruni/1 lmi side network
add fruni/1 dlci/100
*****(dc will be added automatically, DLCI for comn with fruni/2)
set fruni/1 dlci/100 dc rdna 302191332034
*****(Remote DNA of fruni/2 for comn from fruni/1 to 2)
set fruni/1 dlci/100 dc rdlci 100
set fruni/1 dlci/100 dc type permanentmaster (default value, need not
use this command)
****(permanenetslave(fruni/2)
permanentmaster (fruni/1))
****Adding a Fruni/2
will
communicate
with
add fruni/2 (framer, lmi, dna etc will be added automatically)
set fruni/2 framer interfacename lp/4 e1/0 ch/1
set fruni/2 dna dna 302191332034 (DNA of fruni/2)
set fruni/2 lmi procedures itu
set fruni/2 lmi side both
add fruni/2 dlci/100
*****(dc will be added automatically, DLCI for comn with fruni/1)
set fruni/2 dlci/100 dc rdna 302191332033
*****(Remote DNA of fruni/1 for comn from fruni/2 to 1)
set fruni/2 dlci/100 dc rdlci 100
set fruni/2 dlci/100 dc type permanentslave
****(permanenetslave(fruni/2)
permanentmaster (fruni/1))
will
communicate
with
****Add sig on fruni/2 for configuring SVC connectivity
add fruni/2 sig
****command which are deleted below are not required for SVC
configuration
add fruni/2 dlci/17 (dc will be added automatically)
set fruni/2 dlci/17 dc rdna 302191111034
*****(Remote DNA of destination node fruni/2)
set fruni/2 dlci/17 dc rdlci 16
*****(Remote DLCI of destination node fruni/2)
set fruni/2 dlci/16 dc type permanentslave
****(permanenetslave(fruni/2 of this node) will communicate with
permanentmaster (fruni/2 of destination node))
*******Adding Node parameters
set module routingid(rid) 1 (if not existing)
set module moduleid 20 (if not existing)
add module vcs
set module vcs networkidcode 3021 (Used in all DNA addresses)
add module frs (if not existing)
*** Adding Call Server ie Call Router which contains table of DNA
addresses associated with RID and MID
add cr
*** Call Router is added
add cr npi/x121
***Network Plan Indicator (NPI) is added to use X.121 format of
addressing used by DPRS
add cr npi/x121 dna/302191
*****Prefix of DNA is added which is for Region 1 ie RID=1
set cr npi/x121 dna/302191 routingid 1
add cr npi/x121 dna/302191111033
***DNA of fruni/1 on this node which has moduleid=10
set cr npi/x121 dna/302191111033 moduleid 10
add cr npi/x121 dna/302191111034
***DNA of fruni/2 on this node which has moduleid=10
set cr npi/x121 dna/302191111034 moduleid 10
add cr npi/x121 dna/302191332033
***DNA of fruni/1 on destination node which has moduleid=20
set cr npi/x121 dna/302191332033 moduleid 20
add cr npi/x121 dna/302191332034
***DNA of fruni/2 on destination node which has moduleid=20
set cr npi/x121 dna/302191332034 moduleid 20
******Configuration complete check it, activate it and confirm it
check prov
act prov
confirm prov
Note;- Do Not Commit the provisioning
Posted 21st June 2010 by Aryan
0
Add a comment
6.
Apr
25
CONFIGURATION IP OVER ATM ON
MSA E1/0 CH/0 TS 1 TO 4& IP
OPTIMIZED DLCI OVER FR (PVC,
SPVC & SVC)ON MSA E1/0 CH/1 TS 5
TO 8
Configuration on Passport No 1
Add lp/5 e1/0 (Channel/0 will be automatically added)
add lp/5 e1/0 ch/0 atmcell
set lp/5 e1/0 ch/0 timeslots 1 2 3 4
add lp/5 e1/0 ch/1
set lp/5 e1/0 ch/1 timeslots 5 6 7 8
add lp/10 eth100/0
add lp/10 eth100/1
add la/1 (if not already added, framer will be added automatically)
set la/1 framer interfacename lp/10 eth100/0
add la/2 (framer will be automatically added)
set la/2 framer interfacename lp/10 eth100/1
***** vr/0 router must be already existing since it was created during stratup
procedure
add vr/0 (It will be already present)
set vr/0 vrp lp/0 (It will already be there)
add vr/0 ip (if already not added)
add vr/0 ip rip (if already not added)
add vr/0 pp/eth0
set vr/0 pp/eth0 linktomedia la/1
add vr/0 pp/eth0 ipp
add vr/0 pp/eth0 ipp logicalif/192.168.210.1
set vr/0 pp/eth/0 ipp log/192.168.210.1 netmask 255.255.255.0
set vr/0 pp/eth0 ipp log/192.168.210.1 broadcast 192.168.210.255
add vr/0 pp/waneth012
add vr/0 pp/waneth012 ipp
add vr/0 pp/waneth012 ipp log/192.168.1.1
add vr/0 pp/waneth012 ipp log/192.168.1.1 ripif
set vr/0 pp/waneth012 ipp log/192.168.1.1 netmask 255.255.255.252
set vr/0 pp/waneth012 ipp log/192.168.1.1 linktomediaconnection atmmpe/50 ac/1
(Not essential
**** add a new virtual router
add vr/1
set vr/1 vrp lp/0
add vr/1 ip
add vr/1 ip rip
add vr/1 pp/eth1
set vr/1 pp/eth1 linktomedia la/2
add vr/1 pp/eth1 ipp
add vr/1 pp/eth1 ipp logicalif/192.168.100.1
set vr/1 pp/eth/1 ipp log/192.168.100.1 netmask 255.255.255.192
set vr/1 pp/eth1 ipp log/192.168.100.1 broadcast 192.168.100.63
add vr/1 pp/waneth112
add vr/1 pp/waneth112 ipp
add vr/1 pp/waneth112 ipp log/192.168.1.5
add vr/1 pp/waneth112 ipp log/192.168.1.5 ripif
set vr/1 pp/waneth112 ipp log/192.168.1.5 netmask 255.255.255.252
***Commands deleted below are not required for this configuration but next two lines
are ****needed
set vr/1 pp/waneth112 ipp log/192.168.1.5 linktomediaconnection frdte/1 stdlci/100
@
@ This command will work only when frdte/1 and stdlci/100 has been added
set vr/1 pp/waneth112 ipp log/192.168.1.5 linktomediaconnection ipdlcigrp/1 frc/1 @
@ This command will work only when ipdlcigrp/1 has been added
****Adding a atmif and atmmpe
add atmif/50 (ca will be automatically added)
set atmif/50 interfacename lp/5 e1/0 ch/0
set atmif/50 ca minautoselectedvciforvpizero 200
add atmif/50 vcc/0.40 (vcd and tm will be added automatically)
add atmif/50 vcc/0.40 nep
set atmif/50 vcc/0.40 vcd tm txtdt 3
set atmif/50 vcc/0.40 vcd tm txtdp 1 1000
add atmmpe/50 (ac/1 will be added automatically)
set atmmpe/50 linktoprotocolport vr/0 pp/waneth012
set atmmpe/50 ac/1 atmconnection atmif/50 vcc/0.40 nep
set atmmpe/50 ac/1 linktoipinterface vr/0 pp/waneth012 ipp log/192.168.1.1 (not
essential)
**** For configuring IP Optimized DLCI frdte/1 and fruni/1 are not required and new
*****+component called ipdlcigroup had to be added
add ipdlcigrp/1 (this will add frc/1 automatically)
***** It is ipdlcigrp/1 which will be associated with vr/1 pp/waneth112 and
ipdlcigrp/1 frc/1
*****which will be associated with vr/1 pp/waneth112 ipp log/192.168.1.5
*****linktomediaconnection (Note under configuration of vr/1)
set ipdlcigrp/1 linktoprotocolport vr/1 pp/waneth112
****Commands deleted below are not required for IP Optimized DLCI
****Adding a frdte, fruni for Frame Relay Connection on e1/0 ch/1
add frdte/1 (framer, lmi and rg/1 will be added automatically)
delete frdte/1 framer
add frdte/1 vframer
set frdte/1 vframer logicalprocessor(lp) lp/5
add frdte/1 stdlci/100
set frdte/1 rg/1 linktofrdtedlci frdte/1 stdlci/100
set frdte/1 rg/1 linktoprotocolport vr/1 pp/waneth112
set frdte/1 lmi procedures none
***** Adding a fruni/1
add fruni/1 (framer, dna, lmi etc will be added automatically)
delete fruni/1 framer
add fruni/1 vframer
set fruni/1 vframer logicalprocessor(lp) lp/5
set fruni/1 vframer othervirtualframer (ovf) frdte/1 vframer
*******The above command will work only if vframer under frdte/1 has been added)
set fruni/1 dna dna 302191111033 (DNA of fruni/1)
set fruni/1 lmi procedures none
set fruni/1 lmi side network
add fruni/1 dlci/100
*****(dc will be added automatically, DLCI for comn with fruni/2)
set fruni/1 dlci/100 dc rdna 302191111034
*****(Remote DNA of fruni/2 for comn from fruni/1 to 2)
set fruni/1 dlci/100 dc rdlci 100
set fruni/1 dlci/100 dc type permanentmaster (default value, need not use this
command)
****(permanenetslave(fruni/2) will communicate with permanentmaster (fruni/1))
****Adding a Fruni/2
add fruni/2 (framer, lmi, dna etc will be added automatically)
set fruni/2 framer interfacename lp/5 e1/0 ch/1
set fruni/2 dna dna 302191111034 (DNA of fruni/2)
set fruni/2 lmi procedures itu
set fruni/2 lmi side both
****Commands deleted below are not required for IP Optimized DLCI
add fruni/2 dlci/100
*****(dc will be added automatically, DLCI for comn with fruni/1)
*****For IP Optimized DLCI dc should be deleted and ipconnection is added
delete fruni/2 dlci/100 dc
add fruni/2 dlci/100 ipconnection
set fruni/2 dlci/100 ipconnection linktoipdlcigroup ipdlcigrp/1 frc/1
set fruni/2 dlci/100 dc rdna 302191111033
*****(Remote DNA of fruni/1 for comn from fruni/2 to 1)
set fruni/2 dlci/100 dc rdlci 100
set fruni/2 dlci/100 dc type permanentslave
****(permanenetslave(fruni/2) will communicate with permanentmaster (fruni/1))
add fruni/2 dlci/16 (dc will be added automatically)
set fruni/2 dlci/16 dc rdna 302191332034
####
*****(Remote DNA of destination node fruni/2)
set fruni/2 dlci/16 dc rdlci 17
####
####
####
*****(Remote DLCI of destination node fruni/2)
set fruni/2 dlci/16 dc type permanentmaster (default value, need not be configured)
####
****(permanenetslave(fruni/2 of destination
permanentmaster (fruni/2 of this node))
node)
will
*******Adding Node parameters
set module routingid(rid) 1 (if not existing)
set module moduleid 10 (if not existing)
add module vcs
set module vcs networkidcode 3021 (Used in all DNA addresses)
add module frs (if not existing)
communicate
with
*** Adding Call Server ie Call Router which contains table of DNA addresses
associated with RID and MID
*** Command deleted below are not required for IP DLCI Optimized configuration
however, ****even if these are not deleted, it will affect the services engineered
add cr
*** Call Router is added
add cr npi/x121
***Network Plan Indicator (NPI) is added to use X.121 format of addressing used by
DPRS
add cr npi/x121 dna/302191
*****Prefix of DNA is added which is for Region 1 ie RID=1
set cr npi/x121 dna/302191 routingid 1
add cr npi/x121 dna/302191111033
***DNA of fruni/1 on this node which has moduleid=10
set cr npi/x121 dna/302191111033 moduleid 10
add cr npi/x121 dna/302191111034
***DNA of fruni/2 on this node which has moduleid=10
set cr npi/x121 dna/302191111034 moduleid 10
add cr npi/x121 dna/302191332033
***DNA of fruni/1 on destination node which has moduleid=20
set cr npi/x121 dna/302191332033 moduleid 20
add cr npi/x121 dna/302191332034
***DNA of fruni/2 on destination node which has moduleid=20
set cr npi/x121 dna/302191332034 moduleid 20
******Configuration complete check it, activate it and confirm it
check prov
act prov
confirm prov
The above configuration is for engineering of PVC connection. If SPVC connection is
required to be configured, signaling (Sig) has to be added under fruni/2
add fruni/2 sig
check prov
act prov
confirm prov
If the configuration is required for SVC then in addition to above command of adding
sig, command lines marked as #### should be deleted. Once deleted use check prov,
act prov and confirm prov to activate the configuration
Note;- Do Not Commit the provisioning
Configuration on Passport No 2
Add lp/4 e1/0 (Channel/0 will be automatically added)
add lp/4 e1/0 ch/0 atmcell
set lp/4 e1/0 ch/0 timeslots 1 2 3 4
add lp/4 e1/0 ch/1
set lp/4 e1/0 ch/1 timeslots 5 6 7 8
add lp/3 eth100/0
add lp/3 eth100/1
add la/1 (if not already added, framer will be added automatically)
set la/1 framer interfacename lp/3 eth100/0
add la/2 (framer will be automatically added)
set la/2 framer interfacename lp/3 eth100/1
***** vr/0 router must be already existing since it was created during stratup
procedure
add vr/0 (It will be already present)
set vr/0 vrp lp/0 (It will already be there)
add vr/0 ip (if already not added)
add vr/0 ip rip (if already not added)
add vr/0 pp/eth0
set vr/0 pp/eth0 linktomedia la/1
add vr/0 pp/eth0 ipp
add vr/0 pp/eth0 ipp logicalif/192.168.220.1
set vr/0 pp/eth/0 ipp log/192.168.220.1 netmask 255.255.255.0
set vr/0 pp/eth0 ipp log/192.168.220.1 broadcast 192.168.220.255
add vr/0 pp/waneth021
add vr/0 pp/waneth021 ipp
add vr/0 pp/waneth021 ipp log/192.168.1.2
add vr/0 pp/waneth021 ipp log/192.168.1.2 ripif
set vr/0 pp/waneth021 ipp log/192.168.1.2 netmask 255.255.255.252
set vr/0 pp/waneth021 ipp log/192.168.1.2 linktomediaconnection atmmpe/40 ac/1
(Not essential
**** add a new virtual router
add vr/1
set vr/1 vrp lp/0
add vr/1 ip
add vr/1 ip rip
add vr/1 pp/eth1
set vr/1 pp/eth1 linktomedia la/2
add vr/1 pp/eth1 ipp
add vr/1 pp/eth1 ipp logicalif/192.168.100.65
set vr/1 pp/eth/1 ipp log/192.168.100.65 netmask 255.255.255.192
set vr/1 pp/eth1 ipp log/192.168.100.65 broadcast 192.168.100.127
add vr/1 pp/waneth121
add vr/1 pp/waneth121 ipp
add vr/1 pp/waneth121 ipp log/192.168.1.6
add vr/1 pp/waneth121 ipp log/192.168.1.6 ripif
set vr/1 pp/waneth121 ipp log/192.168.1.6 netmask 255.255.255.252
***Commands deleted below are not required for this configuration but next two lines
are ****needed
set vr/1 pp/waneth121 ipp log/192.168.1.6 linktomediaconnection frdte/1 stdlci/100
@
@ This command will work only when frdte/1 and stdlci/100 has been added
set vr/1 pp/waneth121 ipp log/192.168.1.6 linktomediaconnection ipdlcigrp/1 frc/1 @
@ This command will work only when ipdlcigrp/1 has been added
****Adding a atmif and atmmpe
add atmif/40 (ca will be automatically added)
set atmif/40 interfacename lp/4 e1/0 ch/0
set atmif/40 ca minautoselectedvciforvpizero 200
add atmif/40 vcc/0.40 (vcd and tm will be added automatically)
add atmif/40 vcc/0.40 nep
set atmif/40 vcc/0.40 vcd tm txtdt 3
set atmif/40 vcc/0.40 vcd tm txtdp 1 1000
add atmmpe/40 (ac/1 will be added automatically)
set atmmpe/40 linktoprotocolport vr/0 pp/waneth021
set atmmpe/40 ac/1 atmconnection atmif/40 vcc/0.40 nep
set atmmpe/40 ac/1 linktoipinterface vr/0 pp/waneth021 ipp log/192.168.1.2 (not
essential)
**** For configuring IP Optimized DLCI frdte/1 and fruni/1 are not required and new
*****+component called ipdlcigroup had to be added
add ipdlcigrp/1 (this will add frc/1 automatically)
***** It is ipdlcigrp/1 which will be associated with vr/1 pp/waneth121 and
ipdlcigrp/1 frc/1
*****which will be associated with vr/1 pp/waneth121 ipp log/192.168.1.6
*****linktomediaconnection (Note under configuration of vr/1)
set ipdlcigrp/1 linktoprotocolport vr/1 pp/waneth121
****Commands deleted below are not required for IP Optimized DLCI
****Adding a frdte, fruni for Frame Relay Connection on e1/0 ch/1
add frdte/1 (framer, lmi and rg/1 will be added automatically)
delete frdte/1 framer
add frdte/1 vframer
set frdte/1 vframer logicalprocessor(lp) lp/4
add frdte/1 stdlci/100
set frdte/1 rg/1 linktofrdtedlci frdte/1 stdlci/100
set frdte/1 rg/1 linktoprotocolport vr/1 pp/waneth121
set frdte/1 lmi procedures none
***** Adding a fruni/1
add fruni/1 (framer, dna, lmi etc will be added automatically)
delete fruni/1 framer
add fruni/1 vframer
set fruni/1 vframer logicalprocessor(lp) lp/4
set fruni/1 vframer othervirtualframer (ovf) frdte/1 vframer
*******The above command will work only if vframer under frdte/1 has been added)
set fruni/1 dna dna 302191332033 (DNA of fruni/1)
set fruni/1 lmi procedures none
set fruni/1 lmi side network
add fruni/1 dlci/100
*****(dc will be added automatically, DLCI for comn with fruni/2)
set fruni/1 dlci/100 dc rdna 302191332034
*****(Remote DNA of fruni/2 for comn from fruni/1 to 2)
set fruni/1 dlci/100 dc rdlci 100
set fruni/1 dlci/100 dc type permanentmaster (default value, need not use this
command)
****(permanenetslave(fruni/2) will communicate with permanentmaster (fruni/1))
****Adding a Fruni/2
add fruni/2 (framer, lmi, dna etc will be added automatically)
set fruni/2 framer interfacename lp/4 e1/0 ch/1
set fruni/2 dna dna 302191332034 (DNA of fruni/2)
set fruni/2 lmi procedures itu
set fruni/2 lmi side both
****Commands deleted below are not required for IP Optimized DLCI
add fruni/2 dlci/100
*****(dc will be added automatically, DLCI for comn with fruni/1)
*****For IP Optimized DLCI dc should be deleted and ipconnection is added
delete fruni/2 dlci/100 dc
add fruni/2 dlci/100 ipconnection
set fruni/2 dlci/100 ipconnection linktoipdlcigroup ipdlcigrp/1 frc/1
set fruni/2 dlci/100 dc rdna 302191332033
*****(Remote DNA of fruni/1 for comn from fruni/2 to 1)
set fruni/2 dlci/100 dc rdlci 100
set fruni/2 dlci/100 dc type permanentslave
****(permanenetslave(fruni/2) will communicate with permanentmaster (fruni/1))
add fruni/2 dlci/17 (dc will be added automatically)
set fruni/2 dlci/17 dc rdna 302191111034
####
*****(Remote DNA of destination node fruni/2)
set fruni/2 dlci/17 dc rdlci 16
####
####
####
*****(Remote DLCI of destination node fruni/2)
####
set fruni/2 dlci/17 dc type permanentslave
****(permanenetslave(fruni/2 of this node) will communicate with permanentmaster
(fruni/2 of destination node))
*******Adding Node parameters
set module routingid(rid) 1 (if not existing)
set module moduleid 20 (if not existing)
add module vcs
set module vcs networkidcode 3021 (Used in all DNA addresses)
add module frs (if not existing)
*** Adding Call Server ie Call Router which contains table of DNA addresses
associated with RID and MID
*** Command deleted below are not required for IP DLCI Optimized configuration
however, ****even if these are not deleted, it will affect the services engineered
add cr
*** Call Router is added
add cr npi/x121
***Network Plan Indicator (NPI) is added to use X.121 format of addressing used by
DPRS
add cr npi/x121 dna/302191
*****Prefix of DNA is added which is for Region 1 ie RID=1
set cr npi/x121 dna/302191 routingid 1
add cr npi/x121 dna/302191111033
***DNA of fruni/1 on this node which has moduleid=10
set cr npi/x121 dna/302191111033 moduleid 10
add npi/x121 dna/302191111034
***DNA of fruni/2 on this node which has moduleid=10
set cr npi/x121 dna/302191111034 moduleid 10
add cr npi/x121 dna/302191332033
***DNA of fruni/1 on destination node which has moduleid=20
set cr npi/x121 dna/302191332033 moduleid 20
add cr npi/x121 dna/302191332034
***DNA of fruni/2 on destination node which has moduleid=20
set cr npi/x121 dna/302191332034 moduleid 20
******Configuration complete check it, activate it and confirm it
check prov
act prov
confirm prov
The above configuration is for engineering of PVC connection. If SPVC connection is
required to be configured, signaling (Sig) has to be added under fruni/2
add fruni/2 sig
check prov
act prov
confirm prov
If the configuration is required for SVC then in addition to above command of adding
sig, command lines marked as #### should be deleted. Once deleted use check prov,
act prov and confirm prov to activate the configuration
Note;- Do Not Commit the provisioning
Posted 25th April 2010 by Aryan
0
Add a comment
7.
Apr
25
CONFIGURATION IP OVER ATM ON
MSA E1/0 CH/0 TS 1 TO 4& IP OVER
FR (SVC)ON MSA E1/0 CH/1 TS 5 TO
8
Configuration on Passport No 1
Add lp/5 e1/0 (Channel/0 will be automatically added)
add lp/5 e1/0 ch/0 atmcell
set lp/5 e1/0 ch/0 timeslots 1 2 3 4
add lp/5 e1/0 ch/1
set lp/5 e1/0 ch/1 timeslots 5 6 7 8
add lp/10 eth100/0
add lp/10 eth100/1
add la/1 (if not already added, framer will be added automatically)
set la/1 framer interfacename lp/10 eth100/0
add la/2 (framer will be automatically added)
set la/2 framer interfacename lp/10 eth100/1
***** vr/0 router must be already existing since it was created during stratup
procedure
add vr/0 (It will be already present)
set vr/0 vrp lp/0 (It will already be there)
add vr/0 ip (if already not added)
add vr/0 ip rip (if already not added)
add vr/0 pp/eth0
set vr/0 pp/eth0 linktomedia la/1
add vr/0 pp/eth0 ipp
add vr/0 pp/eth0 ipp logicalif/192.168.210.1
set vr/0 pp/eth/0 ipp log/192.168.210.1 netmask 255.255.255.0
set vr/0 pp/eth0 ipp log/192.168.210.1 broadcast 192.168.210.255
add vr/0 pp/waneth012
add vr/0 pp/waneth012 ipp
add vr/0 pp/waneth012 ipp log/192.168.1.1
add vr/0 pp/waneth012 ipp log/192.168.1.1 ripif
set vr/0 pp/waneth012 ipp log/192.168.1.1 netmask 255.255.255.252
set vr/0 pp/waneth012 ipp log/192.168.1.1 linktomediaconnection atmmpe/50 ac/1
(Not essential
**** add a new virtual router
add vr/1
set vr/1 vrp lp/0
add vr/1 ip
add vr/1 ip rip
add vr/1 pp/eth1
set vr/1 pp/eth1 linktomedia la/2
add vr/1 pp/eth1 ipp
add vr/1 pp/eth1 ipp logicalif/192.168.100.1
set vr/1 pp/eth/1 ipp log/192.168.100.1 netmask 255.255.255.192
set vr/1 pp/eth1 ipp log/192.168.100.1 broadcast 192.168.100.63
add vr/1 pp/waneth112
add vr/1 pp/waneth112 ipp
add vr/1 pp/waneth112 ipp log/192.168.1.5
add vr/1 pp/waneth112 ipp log/192.168.1.5 ripif
set vr/1 pp/waneth112 ipp log/192.168.1.5 netmask 255.255.255.252
set vr/1 pp/waneth112 ipp log/192.168.1.5 linktomediaconnection frdte/1 stdlci/100
@
@ This command will work only when frdte/1 and stdlci/100 has been added
****Adding a atmif and atmmpe
add atmif/50 (ca will be automatically added)
set atmif/50 interfacename lp/5 e1/0 ch/0
set atmif/50 ca minautoselectedvciforvpizero 200
add atmif/50 vcc/0.40 (vcd and tm will be added automatically)
add atmif/50 vcc/0.40 nep
set atmif/50 vcc/0.40 vcd tm txtdt 3
set atmif/50 vcc/0.40 vcd tm txtdp 1 1000
add atmmpe/50 (ac/1 will be added automatically)
set atmmpe/50 linktoprotocolport vr/0 pp/waneth012
set atmmpe/50 ac/1 atmconnection atmif/50 vcc/0.40 nep
set atmmpe/50 ac/1 linktoipinterface vr/0 pp/waneth012 ipp log/192.168.1.1 (not
essential)
****Adding a frdte, fruni for Frame Relay Connection on e1/0 ch/1
add frdte/1 (framer, lmi and rg/1 will be added automatically)
delete frdte/1 framer
add frdte/1 vframer
set frdte/1 vframer logicalprocessor(lp) lp/5
add frdte/1 stdlci/100
set frdte/1 rg/1 linktofrdtedlci frdte/1 stdlci/100
set frdte/1 rg/1 linktoprotocolport vr/1 pp/waneth112
set frdte/1 lmi procedures none
***** Adding a fruni/1
add fruni/1 (framer, dna, lmi etc will be added automatically)
delete fruni/1 framer
add fruni/1 vframer
set fruni/1 vframer logicalprocessor(lp) lp/5
set fruni/1 vframer othervirtualframer (ovf) frdte/1 vframer
*******The above command will work only if vframer under frdte/1 has been added)
set fruni/1 dna dna 302191111033 (DNA of fruni/1)
set fruni/1 lmi procedures none
set fruni/1 lmi side network
add fruni/1 dlci/100
*****(dc will be added automatically, DLCI for comn with fruni/2)
set fruni/1 dlci/100 dc rdna 302191111034
*****(Remote DNA of fruni/2 for comn from fruni/1 to 2)
set fruni/1 dlci/100 dc rdlci 100
set fruni/1 dlci/100 dc type permanentmaster (default value, need not use this
command)
****(permanenetslave(fruni/2) will communicate with permanentmaster (fruni/1))
****Adding a Fruni/2
add fruni/2 (framer, lmi, dna etc will be added automatically)
set fruni/2 framer interfacename lp/5 e1/0 ch/1
set fruni/2 dna dna 302191111034 (DNA of fruni/2)
set fruni/2 lmi procedures itu
set fruni/2 lmi side both
add fruni/2 dlci/100
*****(dc will be added automatically, DLCI for comn with fruni/1)
set fruni/2 dlci/100 dc rdna 302191111033
*****(Remote DNA of fruni/1 for comn from fruni/2 to 1)
set fruni/2 dlci/100 dc rdlci 100
set fruni/2 dlci/100 dc type permanentslave
****(permanenetslave(fruni/2) will communicate with permanentmaster (fruni/1))
****Add sig on fruni/2 for configuring SVC connectivity
add fruni/2 sig
****command which are deleted below are not required for SVC configuration
add fruni/2 dlci/16 (dc will be added automatically)
set fruni/2 dlci/16 dc rdna 302191332034
*****(Remote DNA of destination node fruni/2)
set fruni/2 dlci/16 dc rdlci 17
*****(Remote DLCI of destination node fruni/2)
set fruni/2 dlci/16 dc type permanentmaster (default value, need not be configured)
****(permanenetslave(fruni/2 of destination
permanentmaster (fruni/2 of this node))
node)
will
communicate
with
*******Adding Node parameters
set module routingid(rid) 1 (if not existing)
set module moduleid 10 (if not existing)
add module vcs
set module vcs networkidcode 3021 (Used in all DNA addresses)
add module frs (if not existing)
*** Adding Call Server ie Call Router which contains table of DNA addresses
associated with RID and MID
add cr
*** Call Router is added
add cr npi/x121
***Network Plan Indicator (NPI) is added to use X.121 format of addressing used by
DPRS
add cr npi/x121 dna/302191
*****Prefix of DNA is added which is for Region 1 ie RID=1
set cr npi/x121 dna/302191 routingid 1
add cr npi/x121 dna/302191111033
***DNA of fruni/1 on this node which has moduleid=10
set cr npi/x121 dna/302191111033 moduleid 10
add cr npi/x121 dna/302191111034
***DNA of fruni/2 on this node which has moduleid=10
set cr npi/x121 dna/302191111034 moduleid 10
add cr npi/x121 dna/302191332033
***DNA of fruni/1 on destination node which has moduleid=20
set cr npi/x121 dna/302191332033 moduleid 20
add cr npi/x121 dna/302191332034
***DNA of fruni/2 on destination node which has moduleid=20
set cr npi/x121 dna/302191332034 moduleid 20
******Configuration complete check it, activate it and confirm it
check prov
act prov
confirm prov
Note;- Do Not Commit the provisioning
Configuration on Passport No 2
Add lp/4 e1/0 (Channel/0 will be automatically added)
add lp/4 e1/0 ch/0 atmcell
set lp/4 e1/0 ch/0 timeslots 1 2 3 4
add lp/4 e1/0 ch/1
set lp/4 e1/0 ch/1 timeslots 5 6 7 8
add lp/3 eth100/0
add lp/3 eth100/1
add la/1 (if not already added, framer will be added automatically)
set la/1 framer interfacename lp/3 eth100/0
add la/2 (framer will be automatically added)
set la/2 framer interfacename lp/3 eth100/1
***** vr/0 router must be already existing since it was created during stratup
procedure
add vr/0 (It will be already present)
set vr/0 vrp lp/0 (It will already be there)
add vr/0 ip (if already not added)
add vr/0 ip rip (if already not added)
add vr/0 pp/eth0
set vr/0 pp/eth0 linktomedia la/1
add vr/0 pp/eth0 ipp
add vr/0 pp/eth0 ipp logicalif/192.168.220.1
set vr/0 pp/eth/0 ipp log/192.168.220.1 netmask 255.255.255.0
set vr/0 pp/eth0 ipp log/192.168.220.1 broadcast 192.168.220.255
add vr/0 pp/waneth021
add vr/0 pp/waneth021 ipp
add vr/0 pp/waneth021 ipp log/192.168.1.2
add vr/0 pp/waneth021 ipp log/192.168.1.2 ripif
set vr/0 pp/waneth021 ipp log/192.168.1.2 netmask 255.255.255.252
set vr/0 pp/waneth021 ipp log/192.168.1.2 linktomediaconnection atmmpe/40 ac/1
(Not essential
**** add a new virtual router
add vr/1
set vr/1 vrp lp/0
add vr/1 ip
add vr/1 ip rip
add vr/1 pp/eth1
set vr/1 pp/eth1 linktomedia la/2
add vr/1 pp/eth1 ipp
add vr/1 pp/eth1 ipp logicalif/192.168.100.65
set vr/1 pp/eth/1 ipp log/192.168.100.65 netmask 255.255.255.192
set vr/1 pp/eth1 ipp log/192.168.100.65 broadcast 192.168.100.127
add vr/1 pp/waneth121
add vr/1 pp/waneth121 ipp
add vr/1 pp/waneth121 ipp log/192.168.1.6
add vr/1 pp/waneth121 ipp log/192.168.1.6 ripif
set vr/1 pp/waneth121 ipp log/192.168.1.6 netmask 255.255.255.252
set vr/1 pp/waneth121 ipp log/192.168.1.6 linktomediaconnection frdte/1 stdlci/100
@
@ This command will work only when frdte/1 and stdlci/100 has been added
****Adding a atmif and atmmpe
add atmif/40 (ca will be automatically added)
set atmif/40 interfacename lp/4 e1/0 ch/0
set atmif/40 ca minautoselectedvciforvpizero 200
add atmif/40 vcc/0.40 (vcd and tm will be added automatically)
add atmif/40 vcc/0.40 nep
set atmif/40 vcc/0.40 vcd tm txtdt 3
set atmif/40 vcc/0.40 vcd tm txtdp 1 1000
add atmmpe/40 (ac/1 will be added automatically)
set atmmpe/40 linktoprotocolport vr/0 pp/waneth021
set atmmpe/40 ac/1 atmconnection atmif/40 vcc/0.40 nep
set atmmpe/40 ac/1 linktoipinterface vr/0 pp/waneth021 ipp log/192.168.1.2 (not
essential)
****Adding a frdte, fruni for Frame Relay Connection on e1/0 ch/1
add frdte/1 (framer, lmi and rg/1 will be added automatically)
delete frdte/1 framer
add frdte/1 vframer
set frdte/1 vframer logicalprocessor(lp) lp/4
add frdte/1 stdlci/100
set frdte/1 rg/1 linktofrdtedlci frdte/1 stdlci/100
set frdte/1 rg/1 linktoprotocolport vr/1 pp/waneth121
set frdte/1 lmi procedures none
***** Adding a fruni/1
add fruni/1 (framer, dna, lmi etc will be added automatically)
delete fruni/1 framer
add fruni/1 vframer
set fruni/1 vframer logicalprocessor(lp) lp/4
set fruni/1 vframer othervirtualframer (ovf) frdte/1 vframer
*******The above command will work only if vframer under frdte/1 has been added)
set fruni/1 dna dna 302191332033 (DNA of fruni/1)
set fruni/1 lmi procedures none
set fruni/1 lmi side network
add fruni/1 dlci/100
*****(dc will be added automatically, DLCI for comn with fruni/2)
set fruni/1 dlci/100 dc rdna 302191332034
*****(Remote DNA of fruni/2 for comn from fruni/1 to 2)
set fruni/1 dlci/100 dc rdlci 100
set fruni/1 dlci/100 dc type permanentmaster (default value, need not use this
command)
****(permanenetslave(fruni/2) will communicate with permanentmaster (fruni/1))
****Adding a Fruni/2
add fruni/2 (framer, lmi, dna etc will be added automatically)
set fruni/2 framer interfacename lp/4 e1/0 ch/1
set fruni/2 dna dna 302191332034 (DNA of fruni/2)
set fruni/2 lmi procedures itu
set fruni/2 lmi side both
add fruni/2 dlci/100
*****(dc will be added automatically, DLCI for comn with fruni/1)
set fruni/2 dlci/100 dc rdna 302191332033
*****(Remote DNA of fruni/1 for comn from fruni/2 to 1)
set fruni/2 dlci/100 dc rdlci 100
set fruni/2 dlci/100 dc type permanentslave
****(permanenetslave(fruni/2) will communicate with permanentmaster (fruni/1))
****Add sig on fruni/2 for configuring SVC connectivity
add fruni/2 sig
****command which are deleted below are not required for SVC configuration
add fruni/2 dlci/17 (dc will be added automatically)
set fruni/2 dlci/17 dc rdna 302191111034
*****(Remote DNA of destination node fruni/2)
set fruni/2 dlci/17 dc rdlci 16
*****(Remote DLCI of destination node fruni/2)
set fruni/2 dlci/16 dc type permanentslave
****(permanenetslave(fruni/2 of this node) will communicate with permanentmaster
(fruni/2 of destination node))
*******Adding Node parameters
set module routingid(rid) 1 (if not existing)
set module moduleid 20 (if not existing)
add module vcs
set module vcs networkidcode 3021 (Used in all DNA addresses)
add module frs (if not existing)
*** Adding Call Server ie Call Router which contains table of DNA addresses
associated with RID and MID
add cr
*** Call Router is added
add cr npi/x121
***Network Plan Indicator (NPI) is added to use X.121 format of addressing used by
DPRS
add cr npi/x121 dna/302191
*****Prefix of DNA is added which is for Region 1 ie RID=1
set cr npi/x121 dna/302191 routingid 1
add cr npi/x121 dna/302191111033
***DNA of fruni/1 on this node which has moduleid=10
set cr npi/x121 dna/302191111033 moduleid 10
add cr npi/x121 dna/302191111034
***DNA of fruni/2 on this node which has moduleid=10
set cr npi/x121 dna/302191111034 moduleid 10
add cr npi/x121 dna/302191332033
***DNA of fruni/1 on destination node which has moduleid=20
set cr npi/x121 dna/302191332033 moduleid 20
add cr npi/x121 dna/302191332034
***DNA of fruni/2 on destination node which has moduleid=20
set cr npi/x121 dna/302191332034 moduleid 20
******Configuration complete check it, activate it and confirm it
check prov
act prov
confirm prov
Note;- Do Not Commit the provisioning
Posted 25th April 2010 by Aryan
0
Add a comment
8.
Apr
25
CONFIGURATION IP OVER ATM ON
MSA E1/0 CH/0 TS 1 TO 4& IP OVER
FR (PVC & SPVC)ON MSA E1/0 CH/1
TS 5 TO 8
Configuration on Passport No 1
Add lp/5 e1/0 (Channel/0 will be automatically added)
add lp/5 e1/0 ch/0 atmcell
set lp/5 e1/0 ch/0 timeslots 1 2 3 4
add lp/5 e1/0 ch/1
set lp/5 e1/0 ch/1 timeslots 5 6 7 8
add lp/10 eth100/0
add lp/10 eth100/1
add la/1 (if not already added, framer will be added automatically)
set la/1 framer interfacename lp/10 eth100/0
add la/2 (framer will be automatically added)
set la/2 framer interfacename lp/10 eth100/1
***** vr/0 router must be already existing since it was created during stratup
procedure
add vr/0 (It will be already present)
set vr/0 vrp lp/0 (It will already be there)
add vr/0 ip (if already not added)
add vr/0 ip rip (if already not added)
add vr/0 pp/eth0
set vr/0 pp/eth0 linktomedia la/1
add vr/0 pp/eth0 ipp
add vr/0 pp/eth0 ipp logicalif/192.168.210.1
set vr/0 pp/eth/0 ipp log/192.168.210.1 netmask 255.255.255.0
set vr/0 pp/eth0 ipp log/192.168.210.1 broadcast 192.168.210.255
add vr/0 pp/waneth012
add vr/0 pp/waneth012 ipp
add vr/0 pp/waneth012 ipp log/192.168.1.1
add vr/0 pp/waneth012 ipp log/192.168.1.1 ripif
set vr/0 pp/waneth012 ipp log/192.168.1.1 netmask 255.255.255.252
set vr/0 pp/waneth012 ipp log/192.168.1.1 linktomediaconnection atmmpe/50 ac/1
(Not essential
**** add a new virtual router
add vr/1
set vr/1 vrp lp/0
add vr/1 ip
add vr/1 ip rip
add vr/1 pp/eth1
set vr/1 pp/eth1 linktomedia la/2
add vr/1 pp/eth1 ipp
add vr/1 pp/eth1 ipp logicalif/192.168.100.1
set vr/1 pp/eth/1 ipp log/192.168.100.1 netmask 255.255.255.192
set vr/1 pp/eth1 ipp log/192.168.100.1 broadcast 192.168.100.63
add vr/1 pp/waneth112
add vr/1 pp/waneth112 ipp
add vr/1 pp/waneth112 ipp log/192.168.1.5
add vr/1 pp/waneth112 ipp log/192.168.1.5 ripif
set vr/1 pp/waneth112 ipp log/192.168.1.5 netmask 255.255.255.252
set vr/1 pp/waneth112 ipp log/192.168.1.5 linktomediaconnection frdte/1 stdlci/100
@
@ This command will work only when frdte/1 and stdlci/100 has been added
****Adding a atmif and atmmpe
add atmif/50 (ca will be automatically added)
set atmif/50 interfacename lp/5 e1/0 ch/0
set atmif/50 ca minautoselectedvciforvpizero 200
add atmif/50 vcc/0.40 (vcd and tm will be added automatically)
add atmif/50 vcc/0.40 nep
set atmif/50 vcc/0.40 vcd tm txtdt 3
set atmif/50 vcc/0.40 vcd tm txtdp 1 1000
add atmmpe/50 (ac/1 will be added automatically)
set atmmpe/50 linktoprotocolport vr/0 pp/waneth012
set atmmpe/50 ac/1 atmconnection atmif/50 vcc/0.40 nep
set atmmpe/50 ac/1 linktoipinterface vr/0 pp/waneth012 ipp log/192.168.1.1 (not
essential)
****Adding a frdte, fruni for Frame Relay Connection on e1/0 ch/1
add frdte/1 (framer, lmi and rg/1 will be added automatically)
delete frdte/1 framer
add frdte/1 vframer
set frdte/1 vframer logicalprocessor(lp) lp/5
add frdte/1 stdlci/100
set frdte/1 rg/1 linktofrdtedlci frdte/1 stdlci/100
set frdte/1 rg/1 linktoprotocolport vr/1 pp/waneth112
set frdte/1 lmi procedures none
***** Adding a fruni/1
add fruni/1 (framer, dna, lmi etc will be added automatically)
delete fruni/1 framer
add fruni/1 vframer
set fruni/1 vframer logicalprocessor(lp) lp/5
set fruni/1 vframer othervirtualframer (ovf) frdte/1 vframer
*******The above command will work only if vframer under frdte/1 has been added)
set fruni/1 dna dna 302191111033 (DNA of fruni/1)
set fruni/1 lmi procedures none
set fruni/1 lmi side network
add fruni/1 dlci/100
*****(dc will be added automatically, DLCI for comn with fruni/2)
set fruni/1 dlci/100 dc rdna 302191111034
*****(Remote DNA of fruni/2 for comn from fruni/1 to 2)
set fruni/1 dlci/100 dc rdlci 100
set fruni/1 dlci/100 dc type permanentmaster (default value, need not use this
command)
****(permanenetslave(fruni/2) will communicate with permanentmaster (fruni/1))
****Adding a Fruni/2
add fruni/2 (framer, lmi, dna etc will be added automatically)
set fruni/2 framer interfacename lp/5 e1/0 ch/1
set fruni/2 dna dna 302191111034 (DNA of fruni/2)
set fruni/2 lmi procedures itu
set fruni/2 lmi side both
add fruni/2 dlci/100
*****(dc will be added automatically, DLCI for comn with fruni/1)
set fruni/2 dlci/100 dc rdna 302191111033
*****(Remote DNA of fruni/1 for comn from fruni/2 to 1)
set fruni/2 dlci/100 dc rdlci 100
set fruni/2 dlci/100 dc type permanentslave
****(permanenetslave(fruni/2) will communicate with permanentmaster (fruni/1))
add fruni/2 dlci/16 (dc will be added automatically)
set fruni/2 dlci/16 dc rdna 302191332034
*****(Remote DNA of destination node fruni/2)
set fruni/2 dlci/16 dc rdlci 17
*****(Remote DLCI of destination node fruni/2)
set fruni/2 dlci/16 dc type permanentmaster (default value, need not be configured)
****(permanenetslave(fruni/2 of destination
permanentmaster (fruni/2 of this node))
node)
will
communicate
with
*******Adding Node parameters
set module routingid(rid) 1 (if not existing)
set module moduleid 10 (if not existing)
add module vcs
set module vcs networkidcode 3021 (Used in all DNA addresses)
add module frs (if not existing)
*** Adding Call Server ie Call Router which contains table of DNA addresses
associated with RID and MID
add cr
*** Call Router is added
add cr npi/x121
***Network Plan Indicator (NPI) is added to use X.121 format of addressing used by
DPRS
add cr npi/x121 dna/302191
*****Prefix of DNA is added which is for Region 1 ie RID=1
set cr npi/x121 dna/302191 routingid 1
add cr npi/x121 dna/302191111033
***DNA of fruni/1 on this node which has moduleid=10
set cr npi/x121 dna/302191111033 moduleid 10
add cr npi/x121 dna/302191111034
***DNA of fruni/2 on this node which has moduleid=10
set cr npi/x121 dna/302191111034 moduleid 10
add cr npi/x121 dna/302191332033
***DNA of fruni/1 on destination node which has moduleid=20
set cr npi/x121 dna/302191332033 moduleid 20
add cr npi/x121 dna/302191332034
***DNA of fruni/2 on destination node which has moduleid=20
set cr npi/x121 dna/302191332034 moduleid 20
******Configuration complete check it, activate it and confirm it
check prov
act prov
confirm prov
Note;- Do Not Commit the provisioning
Configuration on Passport No 2
Add lp/4 e1/0 (Channel/0 will be automatically added)
add lp/4 e1/0 ch/0 atmcell
set lp/4 e1/0 ch/0 timeslots 1 2 3 4
add lp/4 e1/0 ch/1
set lp/4 e1/0 ch/1 timeslots 5 6 7 8
add lp/3 eth100/0
add lp/3 eth100/1
add la/1 (if not already added, framer will be added automatically)
set la/1 framer interfacename lp/3 eth100/0
add la/2 (framer will be automatically added)
set la/2 framer interfacename lp/3 eth100/1
***** vr/0 router must be already existing since it was created during stratup
procedure
add vr/0 (It will be already present)
set vr/0 vrp lp/0 (It will already be there)
add vr/0 ip (if already not added)
add vr/0 ip rip (if already not added)
add vr/0 pp/eth0
set vr/0 pp/eth0 linktomedia la/1
add vr/0 pp/eth0 ipp
add vr/0 pp/eth0 ipp logicalif/192.168.220.1
set vr/0 pp/eth/0 ipp log/192.168.220.1 netmask 255.255.255.0
set vr/0 pp/eth0 ipp log/192.168.220.1 broadcast 192.168.220.255
add vr/0 pp/waneth021
add vr/0 pp/waneth021 ipp
add vr/0 pp/waneth021 ipp log/192.168.1.2
add vr/0 pp/waneth021 ipp log/192.168.1.2 ripif
set vr/0 pp/waneth021 ipp log/192.168.1.2 netmask 255.255.255.252
set vr/0 pp/waneth021 ipp log/192.168.1.2 linktomediaconnection atmmpe/40 ac/1
(Not essential
**** add a new virtual router
add vr/1
set vr/1 vrp lp/0
add vr/1 ip
add vr/1 ip rip
add vr/1 pp/eth1
set vr/1 pp/eth1 linktomedia la/2
add vr/1 pp/eth1 ipp
add vr/1 pp/eth1 ipp logicalif/192.168.100.65
set vr/1 pp/eth/1 ipp log/192.168.100.65 netmask 255.255.255.192
set vr/1 pp/eth1 ipp log/192.168.100.65 broadcast 192.168.100.127
add vr/1 pp/waneth121
add vr/1 pp/waneth121 ipp
add vr/1 pp/waneth121 ipp log/192.168.1.6
add vr/1 pp/waneth121 ipp log/192.168.1.6 ripif
set vr/1 pp/waneth121 ipp log/192.168.1.6 netmask 255.255.255.252
set vr/1 pp/waneth121 ipp log/192.168.1.6 linktomediaconnection frdte/1 stdlci/100
@
@ This command will work only when frdte/1 and stdlci/100 has been added
****Adding a atmif and atmmpe
add atmif/40 (ca will be automatically added)
set atmif/40 interfacename lp/4 e1/0 ch/0
set atmif/40 ca minautoselectedvciforvpizero 200
add atmif/40 vcc/0.40 (vcd and tm will be added automatically)
add atmif/40 vcc/0.40 nep
set atmif/40 vcc/0.40 vcd tm txtdt 3
set atmif/40 vcc/0.40 vcd tm txtdp 1 1000
add atmmpe/40 (ac/1 will be added automatically)
set atmmpe/40 linktoprotocolport vr/0 pp/waneth021
set atmmpe/40 ac/1 atmconnection atmif/40 vcc/0.40 nep
set atmmpe/40 ac/1 linktoipinterface vr/0 pp/waneth021 ipp log/192.168.1.2 (not
essential)
****Adding a frdte, fruni for Frame Relay Connection on e1/0 ch/1
add frdte/1 (framer, lmi and rg/1 will be added automatically)
delete frdte/1 framer
add frdte/1 vframer
set frdte/1 vframer logicalprocessor(lp) lp/4
add frdte/1 stdlci/100
set frdte/1 rg/1 linktofrdtedlci frdte/1 stdlci/100
set frdte/1 rg/1 linktoprotocolport vr/1 pp/waneth121
set frdte/1 lmi procedures none
***** Adding a fruni/1
add fruni/1 (framer, dna, lmi etc will be added automatically)
delete fruni/1 framer
add fruni/1 vframer
set fruni/1 vframer logicalprocessor(lp) lp/4
set fruni/1 vframer othervirtualframer (ovf) frdte/1 vframer
*******The above command will work only if vframer under frdte/1 has been added)
set fruni/1 dna dna 302191332033 (DNA of fruni/1)
set fruni/1 lmi procedures none
set fruni/1 lmi side network
add fruni/1 dlci/100
*****(dc will be added automatically, DLCI for comn with fruni/2)
set fruni/1 dlci/100 dc rdna 302191332034
*****(Remote DNA of fruni/2 for comn from fruni/1 to 2)
set fruni/1 dlci/100 dc rdlci 100
set fruni/1 dlci/100 dc type permanentmaster (default value, need not use this
command)
****(permanenetslave(fruni/2) will communicate with permanentmaster (fruni/1))
****Adding a Fruni/2
add fruni/2 (framer, lmi, dna etc will be added automatically)
set fruni/2 framer interfacename lp/4 e1/0 ch/1
set fruni/2 dna dna 302191332034 (DNA of fruni/2)
set fruni/2 lmi procedures itu
set fruni/2 lmi side both
add fruni/2 dlci/100
*****(dc will be added automatically, DLCI for comn with fruni/1)
set fruni/2 dlci/100 dc rdna 302191332033
*****(Remote DNA of fruni/1 for comn from fruni/2 to 1)
set fruni/2 dlci/100 dc rdlci 100
set fruni/2 dlci/100 dc type permanentslave
****(permanenetslave(fruni/2) will communicate with permanentmaster (fruni/1))
add fruni/2 dlci/17 (dc will be added automatically)
set fruni/2 dlci/17 dc rdna 302191111034
*****(Remote DNA of destination node fruni/2)
set fruni/2 dlci/17 dc rdlci 16
*****(Remote DLCI of destination node fruni/2)
set fruni/2 dlci/16 dc type permanentslave
****(permanenetslave(fruni/2 of this node) will communicate with permanentmaster
(fruni/2 of destination node))
*******Adding Node parameters
set module routingid(rid) 1 (if not existing)
set module moduleid 20 (if not existing)
add module vcs
set module vcs networkidcode 3021 (Used in all DNA addresses)
add module frs (if not existing)
*** Adding Call Server ie Call Router which contains table of DNA addresses
associated with RID and MID
add cr
*** Call Router is added
add cr npi/x121
***Network Plan Indicator (NPI) is added to use X.121 format of addressing used by
DPRS
add cr npi/x121 dna/302191
*****Prefix of DNA is added which is for Region 1 ie RID=1
set cr npi/x121 dna/302191 routingid 1
add cr npi/x121 dna/302191111033
***DNA of fruni/1 on this node which has moduleid=10
set cr npi/x121 dna/302191111033 moduleid 10
add cr npi/x121 dna/302191111034
***DNA of fruni/2 on this node which has moduleid=10
set cr npi/x121 dna/302191111034 moduleid 10
add cr npi/x121 dna/302191332033
***DNA of fruni/1 on destination node which has moduleid=20
set cr npi/x121 dna/302191332033 moduleid 20
add cr npi/x121 dna/302191332034
***DNA of fruni/2 on destination node which has moduleid=20
set cr npi/x121 dna/302191332034 moduleid 20
******Configuration complete check it, activate it and confirm it
check prov
act prov
confirm prov
Note;- Do Not Commit the provisioning
Posted 25th April 2010 by Aryan
3
View comments
9.
Mar
28
CONFIGURING IP OVER ATM
USING 2 PORT ETH100 CARDS FOR
IP, ILS FORWARDER CARD AND 3
PORT E3 ATM IP CARD FOR ATM
(USING ONE VIRTUAL ROUTER
(VR) AND OSPF ROUTING (TWO
AREAS AND BORDER ROUTERS)
PROTOCOL)
Configuration on Passport No 1
Add lp/12 e3/0
add lp/10 eth100/0
add lp/3 ilsfwdr/0
add la/1 (If does not exists)
**** framer will be added automatically
set la/1 framer interfacename lp/10 eth100/0
add vr/0 ip
add vr/0 ip ospf
add vr/0 ip ospf areaentry/0.0.0.0
add vr/0 ip ospf areaentry/1.1.1.1
set vr/0 ip ospf routerid 192.168.210.1 (If not already done)
add vr/0 pp/eth0
set vr/0 pp/eth0 linktomedia la/1
add vr/0 pp/eth0 ipp
add vr/0 pp/eth0 ipp logicalif/192.168.210.1
add vr/0 pp/eth0 ipp logicalif/192.168.210.1 ospfif
set vr/0 pp/eth0 ipp logicalif/192.168.210.1 ospfif areaid 1.1.1.1
set vr/0 pp/eth/0 ipp log/192.168.210.1 netmask 255.255.255.0
set vr/0 pp/eth0 ipp log/192.168.210.1 broadcast 192.168.210.255
add vr/0 pp/waneth012
add vr/0 pp/waneth012 ipp
add vr/0 pp/waneth012 ipp log/192.168.1.1
add vr/0 pp/waneth012 ipp log/192.168.1.1 ospfif
set vr/0 pp/waneth012 ipp log/192.168.1.1 ospif areaid 0.0.0.0
set vr/0 pp/waneth012 ipp log/192.168.1.1 netmask 255.255.255.252
add atmif/120
*** ca and other subcomponents/attributes will be automatically added
set atmif/120 interfacename lp/12 e3/0
set atmif/120 ca minautselectedvciforvpizero 200
add atmif/120 vcc/0.120
**** vcd and other subcomponents/attributes will be added automatically
add atmif/120 vcc/0.120 nep
set atmif/120 vcd tm txtdt 3
set atmif/120 vcd tm txtdp 1 1000
add atmmpe/120
****ac/1 and other attributes/subcomponents will be added automatically
set atmmpe/120 linktoprotocolport vr/0 pp/waneth012
set atmmpe/120 ilsforwarder lp/3 ilsfwdr/0
set atmmpe/120 ac/1 atmconnection atmif/120 vcc/0.120 nep
set atmmpe/120 ac/1 linktoipinterface vr/0 pp/waneth012 ipp log/192.168.1.1 (Not
essential)
check prov
activate prov
confirm prov
Note;- Do Not Commit the provisioning
Configuration on Passport No 2
Add lp/12 e3/0
add lp/3 eth100/0
add lp/2 ilsfwdr/0
add la/1 (If does not exists)
**** framer will be added automatically
set la/1 framer interfacename lp/3 eth100/0
add vr/0 ip
add vr/0 ip ospf
add vr/0 ip ospf areaentry/0.0.0.0
add vr/0 ip ospf areaentry/2.2.2.2
set vr/0 ip ospf routerid 192.168.220.1 (If not already done)
add vr/0 pp/eth0
set vr/0 pp/eth0 linktomedia la/1
add vr/0 pp/eth0 ipp
add vr/0 pp/eth0 ipp logicalif/192.168.220.1
add vr/0 pp/eth0 ipp logicalif/192.168.220.1 ospfif
set vr/0 pp/eth0 ipp logicalif/192.168.220.1 ospfif areaid 2.2.2.2
set vr/0 pp/eth/0 ipp log/192.168.220.1 netmask 255.255.255.0
set vr/0 pp/eth0 ipp log/192.168.220.1 broadcast 192.168.220.255
add vr/0 pp/waneth021
add vr/0 pp/waneth021 ipp
add vr/0 pp/waneth021 ipp log/192.168.1.2
add vr/0 pp/waneth021 ipp log/192.168.1.2 ospfif
set vr/0 pp/waneth021 ipp log/192.168.1.2 ospfif areaid 0.0.0.0
set vr/0 pp/waneth021 ipp log/192.168.1.2 netmask 255.255.255.252
add atmif/120
*** ca and other subcomponents/attributes will be automatically added
set atmif/120 interfacename lp/12 e3/0
set atmif/120 ca minautselectedvciforvpizero 200
add atmif/120 vcc/0.120
**** vcd and other subcomponents/attributes will be added automatically
add atmif/120 vcc/0.120 nep
set atmif/120 vcd tm txtdt 3
set atmif/120 vcd tm txtdp 1 1000
add atmmpe/120
****ac/1 and other attributes/subcomponents will be added automatically
set atmmpe/120 linktoprotocolport vr/0 pp/waneth021
set atmmpe/120 ilsforwarder lp/2 ilsfwdr/0
set atmmpe/120 ac/1 atmconnection atmif/120 vcc/0.120 nep
set atmmpe/120 ac/1 linktoipinterface vr/0 pp/waneth021 ipp log/192.168.1.2 (Not
essential)
check prov
activate prov
confirm prov
Note;- Do Not Commit the provisioning
Posted 28th March 2010 by Aryan
0
Add a comment
10.
Mar
28
CONFIGURING IP OVER ATM
USING 2 PORT ETH100 CARDS FOR
IP, ILS FORWARDER CARD AND 3
PORT E3 ATM IP CARD FOR ATM
(USING ONE VIRTUAL ROUTER
(VR) AND OSPF ROUTING (ONE
AREA) PROTOCOL)
IP traffic can be transported over ATM connectivity using ATM Multiprotocol
Encapsulation. The IP subnet is configured on one of the Ethernet port of 2 Port
Eth100 FP and ATM interface is configured on one of the port of a 3 Port E3 ATM IP
Card. The serial interfaces for WAN connectivity is configured on a virtual router
configured in the Passport Node. The connectivity between serial interface on the
virtual router to ATM interface is provided using ATMMPE software and using ILS
Forwarder Card. The ILS Forwarder card encapsulates the IP packets in to ATM Cells
and forwards the same to the destination through 3 Port E3 ATM IP Card. At the
destination the ATM Cells received on the ATM interface are forwarded to ATMMPE
through ILS Forwarder Card which converts it back to IP Packets and sends it to
serial interface for onward dispatch to Ethernet port.
Configuration on Passport No 1
Add lp/12 e3/0
add lp/10 eth100/0
add lp/3 ilsfwdr/0
add la/1 (If does not exists)
**** framer will be added automatically
set la/1 framer interfacename lp/10 eth100/0
add vr/0 ip
add vr/0 ip ospf
add vr/0 ip ospf areaentry/1.1.1.1
set vr/0 ip ospf routerid 192.168.210.1 (If not already done)
add vr/0 pp/eth0
set vr/0 pp/eth0 linktomedia la/1
add vr/0 pp/eth0 ipp
add vr/0 pp/eth0 ipp logicalif/192.168.210.1
add vr/0 pp/eth0 ipp logicalif/192.168.210.1 ospfif
set vr/0 pp/eth0 ipp logicalif/192.168.210.1 ospfif areaid 1.1.1.1
set vr/0 pp/eth/0 ipp log/192.168.210.1 netmask 255.255.255.0
set vr/0 pp/eth0 ipp log/192.168.210.1 broadcast 192.168.210.255
add vr/0 pp/waneth012
add vr/0 pp/waneth012 ipp
add vr/0 pp/waneth012 ipp log/192.168.1.1
add vr/0 pp/waneth012 ipp log/192.168.1.1 ospfif
set vr/0 pp/waneth012 ipp log/192.168.1.1 ofpfif areaid 1.1.1.1
set vr/0 pp/waneth012 ipp log/192.168.1.1 netmask 255.255.255.252
add atmif/120
*** ca and other subcomponents/attributes will be automatically added
set atmif/120 interfacename lp/12 e3/0
set atmif/120 ca minautselectedvciforvpizero 200
add atmif/120 vcc/0.120
**** vcd and other subcomponents/attributes will be added automatically
add atmif/120 vcc/0.120 nep
set atmif/120 vcd tm txtdt 3
set atmif/120 vcd tm txtdp 1 1000
add atmmpe/120
****ac/1 and other attributes/subcomponents will be added automatically
set atmmpe/120 linktoprotocolport vr/0 pp/waneth012
set atmmpe/120 ilsforwarder lp/3 ilsfwdr/0
set atmmpe/120 ac/1 atmconnection atmif/120 vcc/0.120 nep
set atmmpe/120 ac/1 linktoipinterface vr/0 pp/waneth012 ipp log/192.168.1.1 (Not
essential)
check prov
activate prov
confirm prov
Note;- Do Not Commit the provisioning
Configuration on Passport No 2
Add lp/12 e3/0
add lp/3 eth100/0
add lp/2 ilsfwdr/0
add la/1 (If does not exists)
**** framer will be added automatically
set la/1 framer interfacename lp/3 eth100/0
add vr/0 ip
add vr/0 ip ospf
add vr/0 ip ospf areaentry/1.1.1.1
set vr/0 ip ospf routerid 192.168.220.1 (If not already done)
add vr/0 pp/eth0
set vr/0 pp/eth0 linktomedia la/1
add vr/0 pp/eth0 ipp
add vr/0 pp/eth0 ipp logicalif/192.168.220.1
add vr/0 pp/eth0 ipp logicalif/192.168.220.1 ospfif
set vr/0 pp/eth0 ipp logicalif/192.168.220.1 ospfif areaid 1.1.1.1
set vr/0 pp/eth/0 ipp log/192.168.220.1 netmask 255.255.255.0
set vr/0 pp/eth0 ipp log/192.168.220.1 broadcast 192.168.220.255
add vr/0 pp/waneth021
add vr/0 pp/waneth021 ipp
add vr/0 pp/waneth021 ipp log/192.168.1.2
add vr/0 pp/waneth021 ipp log/192.168.1.2 ospfif
set vr/0 pp/waneth021 ipp log/192.168.1.2 ospfif areaid 1.1.1.1
set vr/0 pp/waneth021 ipp log/192.168.1.2 netmask 255.255.255.252
add atmif/120
*** ca and other subcomponents/attributes will be automatically added
set atmif/120 interfacename lp/12 e3/0
set atmif/120 ca minautselectedvciforvpizero 200
add atmif/120 vcc/0.120
**** vcd and other subcomponents/attributes will be added automatically
add atmif/120 vcc/0.120 nep
set atmif/120 vcd tm txtdt 3
set atmif/120 vcd tm txtdp 1 1000
add atmmpe/120
****ac/1 and other attributes/subcomponents will be added automatically
set atmmpe/120 linktoprotocolport vr/0 pp/waneth021
set atmmpe/120 ilsforwarder lp/2 ilsfwdr/0
set atmmpe/120 ac/1 atmconnection atmif/120 vcc/0.120 nep
set atmmpe/120 ac/1 linktoipinterface vr/0 pp/waneth021 ipp log/192.168.1.2 (Not
essential)
check prov
activate prov
confirm prov
Note;- Do Not Commit the provisioning
Posted 28th March 2010 by Aryan
0
Add a comment
Loading
Send feedback
Download PDF
Similar pages