HD-AHD Intelligent High Speed Dome User Manual

HD-AHD Intelligent High Speed Dome
User Manual
Thank you for purchasing our produdts . Please do not hesitate to contact us if there is any question.
Please read this manual careful before instation or application
(Note:This manual is subject to change without notice)
HD-AHD Intelligent High Speed Dome User Manual
Contents
Safeguards…………………………………………………………………………………………………. ...3
Chapter 1
Introduction
1.1
Product Introduction …………………………………………………………………………………..6
1.2
Appearance……………………………………………………………………………………………..6
1.3
Functions……………………………………………………………………………………………….8
1.4
Technical Data…………………………………………………………………………………………9
1.5
Short-cut Commands…………………………………………………………………………………..11
1.6
Glossary………………………..………………………………………………………………………14
Chapter 2 Precautions to Installation
2.1
Preparation…………………………………………………………………………………………….18
2.2
Precautions to Installation……………………………………………………………………………..18
Chapter3
Installation
3.1
Packing Checking ……………………………………………………………………………………..21
3.2
Installation………………………………………………………………………………………….….22
3.3
Dip Switches( Dome Address, Protocol and Baud Rate)……………………………………………...28
Chapter 4
4.1
Installation Method of Different Brackets
Dimensions…………………………………………………………………………………………….31
4.2 Wall Mount…………………………………………………………………………………………….33
4.3 Pending Mount ………………………………………………………………………………………..34
4.4 Corner Adapter ………………………………………………………………………………………..37
Chapter 5
5.1
Operation Guidance
Wiring ………………………………………………………………………………………………...41
5.2 Protocol and Baud Rate Setting ………………………………………………………………………42
5.3 Dome Address Setting………………………………………………………………………………....42
5.4
Install the Camera Module …………………………………………………………………………....42
5.5 Connect to Power……………………………………………………………………………………...44
5.6 Controller Setting……………………………………………………………………………………...44
5.7
Testing ………………………………………………………………………………………………...45
5.8
Finish Testing ………………………………………………………………………………………....45
1
HD-AHD Intelligent High Speed Dome User Manual
Chapter 6 OSD Menu Operation
6.1
Operation in Enlish OSD
6.1.1 Main Menu ………………………………………………………………………………………. . 47
6.1.2 Menu Tree(Submenu)………………………………………… …………………………………… 47
Appendix 1
Lightning and Surge Protection…………………………………………………………………55
Appendix 2 RS485 BUS Connection…………………………………………………………………………55
Appendix 3 Common Problems and Solutions……………………………………………………………….57
Note 1: The key “IRIS+” mentioned in this manual is equal to “OPEN”, and “IRIS-“ is equal to “CLOSE”;
“PRESET” is equal to “SET” (i.e., to edit preshot), while” PREVIEW” is equal to “ACK” (i.e.,
call preshot); “FOCUS-” is equal to “ FAR”.
2
HD-AHD Intelligent High Speed Dome User Manual
Safeguards:
This is to assure the right application of this product and to avoid danger or property loss.The precaution
measures are divided into “Warnings” and “Cautions”, as shown in the following picture;
Warnings: Ignorance of Warings may cause serious injury or death
Cautions: Ingnorance of Cautions may cause injury or property loss.
Warning Follow this safe guard to
Caution Follwing this precaution to avoid
avoid serious injury or death
potential injury or property loss
Warning
1、 All the national and regional electrical safety regulations must be strictly followed during the installation
and application of this product.
2、 Please use standard power adapter DC12V/2A
3、 Do not connect several devices to one power adapter, as adapter overload may cause over-heat or fire
hazard.
4、 Please disconnect power during wiring and disassembling. Operation is not allowed when connected to
power.
5、 When the product is installed on wall or ceiling, the devices should be firmly fixed.
6.
If there is smoke, severe smell or noise in the dome, turn off the power and disconnect the cable
immediately, then contact our after-sales staff.
7.
If the product does not work properly, please contact your dealer of our after-sale sevice center。Never
attempt to disassemble the camera yourself.
(We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.)
3
HD-AHD Intelligent High Speed Dome User Manual
Cautions
1、 Do not drop the dome or subject it to physical shock, and do not expose it to high electromagnetism
radiation. Avoid the equipment installation on viberating surface or shocking places(ignorance can demage
the equipment).
2、 Do not install the dome in extremely hot( onver 60℃)or cold( below-40℃) or damp locations.
3、 Indoor domes should be kept away from rain and moisture.
4
HD-AHD Intelligent High Speed Dome User Manual
Chapter 1 Introduction
1.1 Product Introduction
1.2 Appearance
1.3 Functions
1.4 Technical Data
1.5 Short-cut Commands
1.6 Glossary
5
HD-AHD Intelligent High Speed Dome User Manual
1.1 Product Introduction
For this series of dome cameras,
the 32-bit ARM processor, built-in zoom lens and the decoder
controller are used together. It’s driven by precise stepper motor, and thus responsive, stable, and trembling-free
at any speed.The excellent performance and complete functions has made it a high-tech security product.
1.2 Appearance
Bracket
Connector
Top Housing
Camera frontal cover
Camera Module
Side cover
6
HD-AHD Intelligent High Speed Dome User Manual
Bracket
Connector
Top extemal Housing
Down extamal Housing
Side cover
Camera Module
Infrared light
Light sensor
RPTZ1080-10X-427 Dome
RPTZ1080-10X-428 Dome
7
HD-AHD Intelligent High Speed Dome User Manual
1.3 Functions
l
Aluminum-alloy housing, 4-inch dome cover, black rotating dome, integrated design
l
Ceiling-mount, wall mount, pending (indoor/outdoor) bracket available
l
Precise stepper motor driven, smooth and tremble-free rotation, noise-free
l
32-bit ARM processor, large storage capacity, higher speed, better performance, higher integration, lower
consumption
l
Soft address and hard address optional
l
Can restore factory default settings
l
Simutaneous zoom and speed limit
l
Auto restore――in the menu,User can set how the camera rotates after start
l
Color/ B/W can be set to be Color, B/W, or Auto
l
6 PTZ Pattern:can record all P/T/Z tour
l
Automatic changing of P/T speed: the P/T speed reduces proportionally according to zoom times.
l
128 presets, accuracy less than 0.1º(the dome targets a specific location, can be set and changed
l
Flexible and resettable auto-scan speed
l
16 presets in each tour: dwell time 1-99 seconds at each preset position settable in OSD menu
l
Pan 360°endless, Tilt 0---90°
l
Pan manual speed: 0.1°~180°/S, Tilt manual speed:0.1°~100°/S
l
3 degress of lightning and surge protection
l
Video Transmitting Distance 400 m
l
Support coaxitron function
l
With CE, FCC and ROHS
(1-9 degree optional)
8
HD-AHD Intelligent High Speed Dome User Manual
1.4 Technical Data
Model Name
Items
RPTZ1080-10X
Camera
Sensor
CTU10AH72
1/2.8
IMX238"
CTU10AH108
CMOS
Effective Pixels
1.3MP
Resolution
720P/30fps, 720P/25 fps
IMX322
1/2.8
CMOS
2.0MP
1080P/30 fps,1080P/25 fps,720P/30 fps,
720P/25 fps
Min. Illumination
0.1 Lux
Optical Zoom
10 X
f=5mm~50mm
White Balance
Auto
D/N
ICR
IR light Source
Varical focal IR-Ⅲ generation
IR Wave Length
850nm
IR Control
Auto/Manual
IR life
more than 20,000 hours
2 X ∮18
IR LED QTY
Infrared Distance
50 M
IR Angle
30°,45°
Proccessor
32-bit ARM
Address
0----255(Compatible with hard address and soft address)
Pan Range
360°Endless
Pan Speed
0.1°/S-240°/S(1-64 degree optional)
Tilt Range
0-----90°
Tilt Speed
0.1°/S-100°/S
2Yes
Poin Auto Scan
Horizontal 360 °Scan
Yes
Preshot
128
Preshot Speed
240°/S
Dwell Time at Preshot
1----99 S
9
HD-AHD Intelligent High Speed Dome User Manual
Pattern
6 Groups
Tour
7Groups
Temperature
-10℃-+60℃
Humidity
≤80% No condensation
Communication
RS485 BUS ,Coaxitron control
Baud Rate
2400/4800/9600 /19200bps Optional
Input Power
DC12V/2A
Consumption
15W
Video Out
AHD-BNC
Video Transmitting
400 m
Distance
Weight
1.2Kg
L type bracket and Ceiling Mount forRPTZ1080-10X-427
Installation
Wall-mount bracket and Pendent bracket for RPTZ1080-10X-428
Certificates
ROHS, CE,FCC
10
HD-AHD Intelligent High Speed Dome User Manual
1.5 Short-cut Commands
PREVIEW/
No
Functions
Remark
Camera Power ON
NA
Camera Power OFF
NA
PRESET
PREVIEW
65
PRESET
PREVIEW
BLC ON
66
PRESET
BLC OFF
PREVIEW
ICR Auto
67
PRESET
ICR Color
PREVIEW
ICR B/W
68
PRESET
Home Position
PREVIEW
OSD ON/OFF
69
PRESET
Screen ON/OFF
PREVIEW
Digital Zoom ON
NA
Digital Zoom OFF
NA
70
PRESET
PREVIEW
Auto Focus
71
PRESET
Manual Focus
PREVIEW
Auto Iris
NA
Manual Iris
NA
72
PRESET
PREVIEW
White Balance Auto
73
PRESET
PREVIEW
White Balance Manual
NA
Indoor Mode
NA
Outdoor Mode
NA
ATW
NA
one push WB
NA
Image Freeze ON
NA
Image Freeze OFF
NA
74
PRESET
PREVIEW
75
PRESET
PREVIEW
76
PRESET
PREVIEW
Reserved
77
PRESET
PREVIEW
Reserved
78
Reserved
11
HD-AHD Intelligent High Speed Dome User Manual
PRESET
Reserved
PREVIEW
1080P/30 fps
79
PRESET
720P/30 fps
PREVIEW
1080P/25 fps
80
PRESET
720P/25fps
Home Position in 1
PREVIEW
Minute
81
Home Position in 2
PRESET
Minute
Home Position in 4
PREVIEW
Minute
82
Home Position in 8
PRESET
Minute
Home Position in 10
PREVIEW
Minute
83
Home Position
PRESET
OFF
PREVIEW
Run 1
st
2-Point Scan
84
PRESET
Run 2nd 2-Point Scan
PREVIEW
85
PRESET
nd
Set 2
Default is 1st one
2-Point Scan
Run 3rd
Reserved
2-Point
PREVIEW
Reserved
Scan
86
Set 3rd
2-Point
PRESET
Reserved
Scan
2-point scan at low
When speed is 64 degree, this command is to record the
speed
speed
PREVIEW
87
Set start position of
PRESET
2-point scan
2-point scan at
PREVIEW
88
Reserved
medium speed
12
HD-AHD Intelligent High Speed Dome User Manual
Set end position of
PRESET
2-point scan
2-point scan at high
PREVIEW
Reserved
89
speed
PRESET
Reserved
2-point scan big circle
PREVIEW
90
mode(﹥180°
2-point scan big circle
PRESET
mode(﹤180°)
PREVIEW
Administrator logo in
Reserved
PRESET
User log in
Reserved
PREVIEW
Run Pan Scan
91
92
Dome information
PRESET
Will disappear in 3 S or when joystick moved
dispaly
PREVIEW
Run 16 preshots
93
PRESET
Restart
Press PRESET 93 three times continually
PREVIEW
94
PRESET
PREVIEW
Open OSD Menu
95
PRESET
PREVIEW
96
PRESET
Run 1nd Pattern
PREVIEW
97
PRESET
Run 2rd
PREVIEW
Pattern
98
PRESET
PREVIEW
99
PRESET
Run 1st Tour
PREVIEW
100
PRESET
PREVIEW
101
Run 2nd Tour
Run 3rd
Tour
13
HD-AHD Intelligent High Speed Dome User Manual
Run 4th Tour
PRESET
Run 5th Tour
PREVIEW
102
PRESET
PREVIEW
Run 6th Tour
IR Auto
103
PRESET
IR ON
PREVIEW
IR OFF
104
PRESET
Reserved
PREVIEW
Reserved
105
PRESET
Reserved
PREVIEW
Reserved
106
PRESET
Reserved
PREVIEW
Reserved
107
PRESET
Reserved
PREVIEW
Reserved
108
PRESET
Reserved
PREVIEW
Reserved
109
PRESET
Reserved
PREVIEW
Return to factory
Press PREVIEW 110 once,then press PRESET 110
setting
twice,and press PREVIEW 110 once
110
PRESET
1.6
Glossary
Soft Address
User can set soft address in this dome, thus make it easier in installation and application.
General Address
Address 0 is the general address, which menas the controlling devices can control any dome in a system by
this address, no matter what the current dome address is.
OSD Menu
The dome provides OSD menu for display of system information and information and setting of dome
parameters.
Proportional Pan/Tilt Speed
14
HD-AHD Intelligent High Speed Dome User Manual
Proportional pan/tilt automatically reduces or increases the pan and tilt speeds in proportion to the amount of
zoom. The dome slows down at a larger amout of zoom, and it speeds up at a small amount of zoom.
AUTO Pan SCAN
The dome rotates horizontally 360º continually at a set speed in the set direction . User can also set the starting
and ending position,between which the camera can move back and forth.
Two-point PAN SCAN
The domes moves horizontally from the starting point to the ending point at a set speed in the set direction.
AUTO FLIP
In manual tracking mode, when a target object goes directly beneath the dome, the dome will automatically
rotate 180 degrees in horizontal direction to maintain continuity of tracking. When the dome rotates (flips), the
camera starts moving upward as long as you continue to hold the joystick in the down position. This function can
be realized by image center flip depending on different camera models. The feature can be enabled/disabled
through the menu.。
PRESET (PRESHOT)
Each of the user-definable presets can be programmed to use pan, tilt, camera settings and other settings.
When preset is called, the dome will automatically move to the defined position. User is allowed to add, modify,
delete and call each preset.
PRESET TOUR (Vector Scan)
The dome will moves the continually from the 1st preset to the 16th. If one preset is not set, it skips and
moves directly to the next preset.
PATTERN (PTZ Tour)
A pattern is a memorized, repeating series of pan, tilt, zoom, and preset functions that can be recalled with a
command from a controller or automatically by a configured function (alarm, park, time task, or power-up). By
default the focus and iris are in auto status during the pattern is being memorized.
IR Cut Filter
15
HD-AHD Intelligent High Speed Dome User Manual
The IR cut filter can be set to Auto, Day and Night. In auto mode, the camera is capable of automatically
switching Black & White mode (Night) and Color mode (Day) with regard to environment lightening conditions.
In manual switch mode, user can increase sensitivity in low light conditions by switching to Black & White
mode, while the Color mode is preferred in normal lighting conditions(depends on the camera).
Auto Focus
The auto focus enables the camera to focus automatically to maintain clear video images
User can also press FAR and NEAR to focus. It will resume auto focus when user do P/T/Z controlling.
Auto Iris
The auto iris enables the camera to iris automatically to maintain clear video images
User can also press OPEN and CLOSE to focus. It will resume auto iris when user do P/T/Z controlling.
Backlight Compensation
When there is bright light source in the background, the subject will be dark, like a blackshadow. Backlight
compensation video gain done either manually or automatically to correct the exposure of subjects that are in
front of a bright light source, avoid unclearness of the target in bright background.
16
HD-AHD Intelligent High Speed Dome User Manual
Chapter 2 Precautions to installation
2.1 Preparation
2.2 Precautions to installation
17
HD-AHD Intelligent High Speed Dome User Manual
2.1 Preparation
1.Regulations
1)All electrical safety and fire regulations should be strictly followed.
2)Please check if your camera and accessories are all included in the product package, make sure the location
is suitable for installation and application of the dome,as specified in the manual.
2. Location checking
Make sure there is enough space for the dome and accessories in the chose location.
3. Check the supporting strength of the chose location
Make sure the ceiling or wall where the dome will be installed is strong enough to support 4 times of the
weight of domes and its accessories.
4. Preparing of cables
Select video cable according to required transmitting distance. Basic requirements of coaxial cable:
1)75Ω;
2)Brass cable;
3)95% copper braid, tinned
2.2 Precautions to installation
1. Read the this manual carefully before installation.
2. The power supply and the voltage should be the same as indicated on the cable. Standard voltage is
DC12V, the voltage should be within DC12V±10%。Long-time working of dome under too low or too high
voltage will cause unnormal working. Keep the power consumption above 40W, otherwise, the restart or
controlling of dome will be unnormal.
3. Continuing exposure of camera to strong light will damage CCD and result in bad image or no display.
4. The outdoor dome is water-proof as well as moisture resistant ( IP66). If the dome is wired improperly, the
rain will enter the dome along the cable, thus damaging the circuit board and even the camera. The right
and wrong wiring are shown in the following pictures:
18
HD-AHD Intelligent High Speed Dome User Manual
Right Wiring
Wrong Wiring
19
HD-AHD Intelligent High Speed Dome User Manual
Chapter 3 Installation
3.1 Package Checking
3.2 Installation
3.3 Dip Switches( Dome Address, Protocol and Baud Rate)
20
HD-AHD Intelligent High Speed Dome User Manual
3.1 Package Checking
Please check if your camera and accessories are all included in the product package:
3.1.1 Packing list of indoor:
1.
Integrated Camera
2.
L Bracket
3.
Power Sypply
4.
User Manual
5.
Quality Certificate
6.
Warranty Card
Integrated Camera
Power Supply(Optional)
L Bracket
User Manual
3.1.2 Packing list of outdoor:
1. Integrated
Camera
2. Bracket
Integrated
Camera
Bracket(Optional)
3. Power Sypply
4. BNC Cable
5. Screw Pack
6. User Manual
7. Quality Certificate
Power Supply(Optional)
BNC Cable
8. Warranty Card
Screw Pack
User Manual
Note:non-original packing material may cause damage in transportation and cost extra charge.
21
HD-AHD Intelligent High Speed Dome User Manual
3.2 Installation
3.2.1 Installation for Indoor Dome
3.2.1.1 Fix L-bracket on the wall
3.2.1.2 Take down the ceiling plate from dome, assemble it into L-Bracket, then install dome into celling
plate, put it into slot, rotate from the right side, then fasten the ceiling plate by PM2.5*8 screws from side of
speed dome. as shown in picture.
22
HD-AHD Intelligent High Speed Dome User Manual
3.2.1.3 Wire of camera is shown as follows:
3.2.1.3.1 One-dome divice connection
The one-dome device connection allows the user learn the wiring quickly, and also makes the installation,
adjusting, testing ,and exhibition easier. Read the below chart carefully for connection when you use the
apparatus for the first time. Any worng wiring may cause permanent damage or damage to other equipments.
AHD-DVR
AHD VIDEO
Caution: No operation is allowed when dome is powered-up.
3.2.3.2 Multi-dome device connection.
When connecting many dome devices together, the user can embed multi-device system with auxiliaries
such as arrester device, video matrix, DVR and alarm box for system integration.
DC12V: Power supply of dome device, which will convert 110V/60HZ to 220V/50HZ input to DC12V
output and supply to the dome device.
RS-485 Bus: It is for the control signal(RS-485 signal) output of controller, connecting to the
communication input terminals of control cable of each dome device.
Video: It is for image signal output of dome device, (can directly output to video equipment such as monitor
or video matrix. Take care of the match up of impedance.)
23
HD-AHD Intelligent High Speed Dome User Manual
3.2.2 Installation for Outdoor Dome
3.2.2.1 Install the bracket: Run the BNC cable through the bracket (see following picture). Please refer to
Chapter 4 for installation of different brackets.
3.2.2.2 For wall mount bracket, get out the upper housing from from the carton and install it with the
bracket. Please wrap the connecting part between the upper housing and the bracket with teflo tapes (see
following picture) to make it water proof if it’s an outddor camera.
24
HD-AHD Intelligent High Speed Dome User Manual
3.2.2.3 Wire of camera is shown as follows:
3.2.2.3.1 One-dome divice connection
The one-dome device connection allows the user learn the wiring quickly, and also makes the installation,
adjusting, testing ,and exhibition easier. Read the below chart carefully for connection when you use the
apparatus for the first time. Any worng wiring may cause permanent damage or damage to other equipments.
AHD VIDEO
AHD-DVR
25
HD-AHD Intelligent High Speed Dome User Manual
BNC Cable
Connector of BNC Cable
1.DC connect to power supply (DC12V input);
2.Video oupout connect to monitor;
3.Orange wire connect to 485+,
Yellow wire connect to 485-;
4. Yellow-green wire connect to ground,can ignoreduring testing.
Caution: No operation is allowed when dome is powered-up.
3.2.2.3.2 Multi-dome device connection.
When connecting many dome devices together, the user can embed multi-device system with auxiliaries
such as arrester device, video matrix, DVR and alarm box for system integration.
DC12V: Power supply of dome device, which will convert 110V/60HZ or 220V/50HZ input to DC12V
output and supply to the dome device.
RS-485 Bus: It is for the control signal(RS-485 signal) output of controller, connecting to the
communication input terminals of control cable of each dome device.
Video: It is for image signal output of dome device, (can directly output to video equipment such as monitor
or video matrix. Take care of the match up of impedance.)
26
HD-AHD Intelligent High Speed Dome User Manual
3.2.3Place the dome upside down, remove the cover of Dip switches board near camera, set dome address
and baud rate. There are two dip switch SW1 & SW2 on master board,, which used for setting dome address,
baud rate and Protocol, see 3.3 dip switches setting.
SW1: Protocol and baud rate setting
SW2: Dome address setting
27
HD-AHD Intelligent High Speed Dome User Manual
3.3 Dip Switches( Dome Address, Protocol and Baud Rate)
3.3.1
Protocol and baud rate(as shown in SW1)
Baud Rate
Protocol
Dip Switch
Note: If you choose “Auto” in protocol, the dome can automatically recognize PELCO-D
D,PELCO-P,
ULTRACK,VICON,, etc. Make sure the dome and controller have the same protocol and baud rate,
otherwise the dome cann’t be controllered. The dome camera should be restarted if there is any change
in the dip switches
3.3.2.Dome address (as shown in SW2)
Dip Switch
Baud rate
3rd Dip
4th Dip
OFF
OFF
4800
ON
OFF
9600
OFF
ON
19200
ON
ON
2400
Dip Switch
Dome Address
(This is Dome address of Dome 1 )
Dip Switch
1st Dip
2nd Dip
Auto
OFF
OFF
DYNACOLOR
ON
OFF
Protocol
28
HD-AHD Intelligent High Speed Dome User Manual
Setting:to add together the corresponding numbers of those DIP at”ON”, and
you get the dome address.
128
1
2
64
4
32
8
16
Corresponding
numbers
Corresponding
numbers
corresponding
numbers
Dip switch&
Dome Address counting example:
2
4
16
(2+4+16=22) Dome address is 22.
Dome adress:0~255
Note:The default factory setting is Auto (protocol), 2400bps(baud rate) and 1(dome address).
29
HD-AHD Intelligent High Speed Dome User Manual
Chapter 4 Installation of Different Brackets
4.1 Dimensions
4.2 Wall Mount
4.3 Pending Mount
4.4 Corner Adapter
30
HD-AHD Intelligent High Speed Dome User Manual
4.1 Dimensions
4.1.1
Wall Mount Bracket
4.1.2
Pendant Bracket
4.1.3 Corner Adapter
31
HD-AHD Intelligent High Speed Dome User Manual
4.1.4
Wall Mount Adapter
4.1.5 Pole Mount Adapter
32
HD-AHD Intelligent High Speed Dome User Manual
4.2 Wall Mount Installation
4.2.1Accessories
(1)Wall Mount Bracket
To use with indoor and outdoor dome
Picture:
(2)Accessories
Bolts, Spring Washers and Plain Washers, Water-proof Washers(Prepared by user)
4.2.2Installing Procedures
Wall Mount is applicable of indoor and outdoor hard walls. Installtion requirements:
(1)The wall is thick enough to support the Bolts, Washers.
(2)The wall can endure at least 8 times of the weight of dome and all the accessories.
Procedure 1:Make a Hole and Fix the Anchor Bolts
Drill 4 holes on the wall according the dimension of wall mount bracket, and insert the M8 anchor
bolts(Prepared by the user) into the holes.
Procedure 2:Run the BNC cable through the wall mount bracket.
Procedure 3:Fix the Wall Mount Bracket on the Wall
Fix the 4 M8 screw caps with plain washers, and then screw them with the corresponding anchor bolts on
the wall (through the wall mount bracket and rubber washer).
Procedure 4:Dome Installation
Connect the BNC cable with dome, then fix the dome to the wall mount bracket with M4 screws.Then
install the speed dome according to Chapter 3
33
HD-AHD Intelligent High Speed Dome User Manual
4.3 Pending Mount Installaiton
4.3.1Accessories
(1)Pending Pan
Used for pending mount installation, should be used together with pipe and connector.
34
HD-AHD Intelligent High Speed Dome User Manual
Picture:
(2)Pipe
4.3.2 Penant Mount Installation
Pendant mount is applied for hard ceiling. Installation Requirements:
(1)The wall is thick enough to support the Bolts, Washers.
(2)The wall can endure at least 5 times of the weight of dome and all the accessories.
Procedure 1:Install the Ceiling Pan
Make 4 holes on the ceiling ( accordingly with the holes on the ceiling pan), insert the anchor botls, then
run the BNC cable throughthe ceiling pan.Then aim the 3 holes on the ceiling pan to the inserted anchor
bolts, and fix with M5 screw.
Note:The length of BNC cable outside ceiling pan should be similar to length of pipe.
Picture:
35
HD-AHD Intelligent High Speed Dome User Manual
Procedure 2:Pipe Installation
Screw the pipe with the connector, then run the BNC cable through the pipe and connector.Thenfix the
pipe with the ceiling pan by M4 Screw。
Picture:
Procedure 3:Dome Installation
Insert BNC cable to connector on top of the dome housing, and then connect the top of domehousing
with pendant bracket (connector) and fix by M4 screw. Then install the dome according to Chapter 3.
36
HD-AHD Intelligent High Speed Dome User Manual
4.4 Corner Adapter Installation
4.4.1Accessories
(1)Wall Mount Bracket
Applcable for indoor and outddor dome.
(2)Corner Adapter
Should be used together with wall mount bracket.
(3)Accessories
Screws, Hexagon Bolts M8, Spring Washers and Plain Washers(Prepared by user)
4.4.2 Installation Procedures
37
HD-AHD Intelligent High Speed Dome User Manual
This is applicable for indoor and outdoor hard walls with 90-degree corner. Installation requirments:
(1)The wall should be thick enough to support the anchor bolts.
(2)The wall can endure at least 8 times the weigh of the dome and all the accessories.
Procedure 1:Install Corner Adapter
Picture:
Mark and drill 6 holes on the wall accordingly with the holes of the corner adapter, andinsertthe M8
anchor bolts.Run the BNC cable through the center hole, then fix the corner adapter to the znchor bolts
by screw caps and washers.
Precaution:The Anchor Bolts are prepared by the user. Assure the cable is long enough.If the dome is used
outdoor, put glass glue to make it water proof.
Procedure 2:Install wall mount bracket to corner bracket.
Use the provided Bolts, Spring Washers and Plain Washers to mount the Wall Mount Adaptor onto the
product (refer to following picture)
Note:when fastening the bolts, first press the washer firmly, then twist about half a circle. Thus can make it
water-proof and also would not damage the bolts because of exceeded sgtrength.
Picture:
38
HD-AHD Intelligent High Speed Dome User Manual
Procedure 3:Install the speed dome
Insert the BNC cable through the wall mount bracket, then screw the bracket with the dome, and fasten
with anchor bolts(M4), then install the speed dome according to Chapter 3.
Picture:
39
HD-AHD Intelligent High Speed Dome User Manual
Chater 5 Operation Guidance
5.1 Wiring
5.2 Protocol and Baud Rate Setting
5.3 Dome Address Setting
5.4 Install the Camera Module
5.5 Connect to Power
5.6 Controller Setting
5.7 Testing
5.8 Finish Testing
40
HD-AHD Intelligent High Speed Dome User Manual
5.1 Wiring(Do not connect to power)
5.1.1 Wiring for indoor dome
5.1.2 Wiring forRPTZ1080-10X-428, dome
41
HD-AHD Intelligent High Speed Dome User Manual
5.2 Protocol and Baud Rate Setting ( Do not set when dome is connected to power; dome should be
restarted if there is any change in the setting) (Please refer to 3.3.1)
The Dip Swich is on PCB Board inside the dome.
5.3 Dome Address Setting ( Do not set when dome is connected to power; dome should be restarted if there
is any change in the setting.)
In left picture:Dome address is:1
(Please refer to 3.3.2)
Dome Address Setting
The Dip Swich is on PCB Board inside the dome.
5.4 Install the Camera Module(Please refer to “ Camera Module Installation”).
1.Connect camera module to FPC cable:
42
HD-AHD Intelligent High Speed Dome User Manual
CTU10AH108
2.Connectors for convert board and master board:
Ear board(6PIN)cable inserting
4PIN,8PIN cable inserting
Camera FPC
3.Connectors for convert board and camera holes, FPC connector
4.Installation finished:
43
HD-AHD Intelligent High Speed Dome User Manual
4PIN,6PIN,8PIN connect cable
Precautions: 1.Connect the FPC cable with camera module in the right way.
2.Different holes (on the main control board) are used for different module.
5.5 Connect to Power.
Now user can see self-checking of both dome (rotating) and camera module(you can see
imageonmonitor)
5.6 Controller Setting
For the controller, the protocol, baud rate and address should be the same as the dome(pleaserefer to the
user manual of cotronller for the detailed setting)
Precaution:
If
the
protocol
of
dome
is
“Auto”,
then
protocol
of
controller
can
be
PELCO-D,PELCO-P,ULTRACK, VICON, etc, but baud rate and address should be the same as dome, otherwise
the dome cann’t be controlled.
44
HD-AHD Intelligent High Speed Dome User Manual
5.7 Testing
Now user can start testing the dome if all the above is done.
1.Pan/Tilt Move Testing
Can be realized by moving joystick left/right or up/down, as shown in following picture:
This means the dome works well.
2.Zoom Testing
User can rotate joystick to zoom in and zoom out or to press the key TELE(Zoom In)and WIDE(Zoom Out)
on the controller.
This means the communication of dome and camera module is good.
(For operations, please refer to the next Chapter for details.)
5.8 Finish Testing(Summary).
1.If everything normal in 5.7, it means the system works well. Please don’t change the wiring or any setting,
to avoid failure in system.
2.If there is any problem in 5/7, please check the wiring ( 5.1 and 5.4) and setting ( 5.2, 5.3 and 5.6)
carefully.
45
HD-AHD Intelligent High Speed Dome User Manual
Chapter 6 Operation in OSD Menu
6.1 The English OSD Menu
6.1.1 Main Menu
6.1.2 Menu Tree(Submenu)
46
HD-AHD Intelligent High Speed Dome User Manual
6.1 Operations in the OSD Menu
6.1.1 Main OSD Display
<1>. Press 95+PREVIEW in the keybarod to enter the OSD Display.
<2>. Move joystick up and down to choose, the item aimed by the arrow is the one been chosen.Press
IRIS+ or move joystick left and right to enter the chosen item andor to change setting.
<3>. Press IRIS- to exit or return to previous item menu.
RPTZ1080-10X
1.Language
English
<<Language Option
2.Display
Setting
<<Display Setting
3.Control
Setting
<<Control Setting
4.System
Setting
<<System Setting
5.Camera
Setting
<< Camera Setting
6.Function
Setting
<< Function Setting
7.Exit
Note:the following icons means
there is drop-down menu.
up
down
6.1.2 Menu Tree (Submenu).
All the submenus are clearly shown in this menu tree.
47
HD-AHD Intelligent High Speed Dome User Manual
1. LANGUAGE
ENGLISH
<< Language Option
2. DISPLAY SETTING
ONLY ENGLISH
<< Display Setting
1. COORDINATES
OFF/ON
<<
Move joystick left&right to choose
2. ZOOM MAG
ON/OFF
<<
Move joystick left&right to choose
3. INIT-INFO DISP
ON/OFF
<<
Move joystick left&right to enter
4. SYSTEM INFORMATION
<<
SYSTEM INFORMATION
CAMEAR
:
CTU10AH108
PROCOTOL :
AUTO
BAUDRATE :
2400
ADDRESS :
RESOLUTION:
SN
:
VERSION
:
IRIS
OPEN TO
1
1080P25
0989694
IAP1.0
RETURN
5.RETURN
<<
3. CONTROL SETTING
1. ADDR AND BAUDRATE
1. ID TYPE
2. INPUT SOFT ID
Move joystick left &right to Exit
<<Control Setting
Move joystick left &right to enter
<<Dome Addr Setup
Move joystick left &right to enter
HARD/BROADCAST/SOFT
1/
0/255---0
Move joystick left &right to choose
Move joystick left &right to choose
3. INPUT S/N
4. S/N
:
5. SOFT BAUD
6. RETUTN
0989694
OFF/2400/4800/9600/19200
2. PAN AND TILT SETUP
1. PAN REVERSE
<<Set Pan And Tilt
OFF/ON
2. TILT REVERSE
OFF/ON
3. -5 TILT LIMIT
OFF /ON
4. RETURN
3. AUTO FLIP
<<
Move joystick left &right to enter
Move joystick left &right to choose
<<
Move joystick left &right to choose
<<
Move joystick left &right to choose
<<
ON/OFF
Move joystick left &right to choose
Move joystick left &right to Exit
Move joystick left &right to Exit
<<
Move joystick left &right to choose
48
HD-AHD Intelligent High Speed Dome User Manual
4. SPEED LIMIT
ON/OFF
5. VECTORSCAN AF
OFF/ON
<<
Move joystick left &right to choose
NA
<<
Move joystick left &right to choose
7. AUTO FOCUS
PTZ/OFF/Z
<<
Move joystick left &right to choose
8. AUTO AE
PTZ/OFF/Z
<<
Move joystick left &right to choose
ON/OFF
<<
Move joystick left &right to choose
<<
Move joystick left &right to Exit
<<System Setting
Move joystick left &right to enter
6. V-SCAN STILL
9. HALF SPEED
10. RETURE
4. SYSTEM SETTING
1. RESOLUTION
720P25
NOTE: RESOLUTION settable
2. CLEAR MEMORY
<<
Move joystick left &right to choose
<<
Move joystick left &right to choose
720P25, 1080P30, 1080P25,720P30
<< Clear Memory
Move joystick left &right to enter
IRIS OPEN TO BEGIN
IRIS CLOSE TO EXIT
INITIALIZING……
3. RESTORE DEFAULT
<< Restore Def Setting
Move joystick left &right to enter
IRIS OPEN TO BEGIN
IRIS CLOSE TO EXIT
PLEASE WAIT……
4. CAMERA RESET
5. RETURN
N/A
<<
Move joystick left &right to Exit
5. CAMERA SETTING
<<
Move joystick left &right to enter
1. SHARPNESS 9
<<
Move joystick left &right to choose
NOTE: SHARPNESS
0---15
2. CAMERA EXPOSURE
<<
Move joystick left &right to enter
1. MODE
AUTO
<<
Move Joystick left &right to choose
NOTE: MODE:AUTO, MANUAL, SHUTTER PRIOR, IRIS PRIOR, BRIGHT PRIOR
2. IRIS
AUTO
<<
Move Joystick left &right to choose
NOTE: IRIS :AUTO ,F14,F11,F.6.9,F8,F6.8,F5.6,F4.8,F4,F3.4,F2.8,F2.4,F2,F1.6,CLOSE
3. GAIN
AUTO
<<
Move Joystick left &right to choose
NOTE: 06DB,08DB,10DB,12DB,14DB,16DB,18DB,20DB,22DB,24DB,26DB,28DB
49
HD-AHD Intelligent High Speed Dome User Manual
4. SHUTTER AUTO
<<
Move Joystick left &right to choose
NOTE: SHUTTER:1/25,1/50,1/75,1/100,1/120,1/150,1/215,1/300,1/425,1/600,1/1000,1/1250,
1/1750,1/2500,,1/3500,1/6000,,1/10000,1/1,1/2,1/3,1/6,1/12
5. BRIGHT AUTO
<<
Move Joystick left &right to choose
NOTE: BRIGHT:AUTO, 0---31
6. SLOW-SHUTTER
OFF/ON
<<
Move Joystick left &right to choose
7. EX-COMP LV
15
<<
Move Joystick left &right to choose
NOTE: EX-COMP LV
0----15
8.RETURN
<<
Move joystick left &right to exit
3. PICTURE FLIP
OFF/ON
<<
Move Joystick left &right to choose
4. LR-REVERSE
OFF/ON
<<
Move Joystick left &right to choose
5. RESOLUTION MODDE
H/L
<<
Move Joystick left &right to choose
6. NR LEVEL
3
<<
Move Joystick left &right to choose
NOTE: NR LEVEL
0---5
7. WDR
OFF/ON
<<
Move Joystick left &right to choose
8. D/N MODE
COLOR
<<
Move Joystick left &right to choose
NOTE: D/N MODE: COLOR, B/W, AUTO
9. RETURN
<<
6. FUNCTION SETTING
<<Function Setting
1. PRESET
<< Preset Setup
1. NUMBER
1---64
2. SET PRESET
Move joystick left &right to exit
Move joystick left &right to enter
Move joystick left &right to enter
<<
Move Joystick left &right to choose
<<
Move joystick left &right to enter
STORED
IRIS CLOSE WHEN DONE
NOTE:Move joystick to position you want to set, press CLOSE to save and exit
3. CALL PRESET
<<
Move joystick left &right to enter
4. DELETE PRESET
<<
Move joystick left &right to enter
5. NAME: _ _ _ _ _ _ _ _ _ _ _ _ _
<< Name Setting
Move joystick left &right to enter
NAME: _ _ _ _ _ _ _ _ _ _ _ _ _
I
IRIS OPEN WHEN DONE
NOTE:Move joystick up &down to choose font, left &right to choose the position
6. NAME DISPLAY
OFF/ON
<< Preset Name Display
50
Move joystick left &right to choose
HD-AHD Intelligent High Speed Dome User Manual
7. RETURN
<<
2. PATTERN
1. NUMBER
( 1~ 6 )
2. PROGRAM
Move joystick left &right to choose
<< Pattern Setup
Move joystick left &right to enter
<< Tour Number
Move joystick left& right to choose
<< EDIT
Move joystick left &right to enter
IRIS OPEN TO BEGIN
IRIS CLOSE TO EXIT
3. RUN
<<
Move joystick left &right to enter
4. DELETE
<<
Move joystick left &right to enter
IRIS OPEN TO BEGIN
IRIS CLOSE TO EXIT
PLEASE WAIT……
5. NAME: _ _ _ _ _ _ _ _ _ _ _ _ _
<< Name Setting
Move joystick left &right to enter
NAME: _ _ _ _ _ _ _ _ _ _ _ _ _
I
IRIS OPEN WHEN DONE
NOTE:Move joystick up &down to choose font, left &right to choose the position
6. NAME DISPLAY
OFF/ON
<<
Move joystick left &right to choose
<<
Move joystick left &right to Exit
<<
Move joystick left &right to exit
<<
Move joystick left &right to choose
<<
Move joystick left &right to enter
1----16
<<
Move joystick left &right to enter
0
<<
Move joystick left &right to choose
7. RETURN
3. VECTORSCAN
1. NUMBER
1----7
2. PROGRAM VECTORSCAN
1. SEQUENCE
2. ELEMENT
NOTE: ELEMENT: PRESET/VECTORSCAN/TOUR
3. ELEMENT
NO.
0
<<
Move joystick left &right to enter
NOTE: ELEMENT NO. :PRESET :1----64/ VECTORSCAN:1----7/ TOUR:1----6
4. SPEED
0
<<
Move joystick left &right to choose
NOTE: SPEED: 1----9
5. DEWELL
0
<<
51
Move joystick left &right to choose
HD-AHD Intelligent High Speed Dome User Manual
NOTE: DEWELL: 1----99
6. RETURN
<<
3. RUN VECTORSCAN
<<
4. DELETE VECTORSCAN
<<
Move joystick left &right to Exit
Move joystick left &right to choose
Move joystick left &right to enter
IRIS OPEN TO BEGIN
IRIS CLOSE TO EXIT
5. RETURN
<<
4. HOME FUNCTION
<<
1. DEFAULT FUNCTION
P/ V/T
<< Set Home Function
Move joystick left &right to Exit
Move joystick left &right to enter
Move joystick left &right to choose
(P:Preset/ V:Vector Scan (Preset Tour)/ T:Tour( Pattern)
2. NUMBER
1
<<
Move joystick left &right to choose
NOTE: NUMBER: P: 1----64/V: 1----7/T: 1----6
3. DELAY
60
NOTE: DELAY
4. OPERATION
<<
Move joystick left &right to choose
1----255
ON/OFF
5. RETURN
5. PAN SCAN SETUP
1. START POINTER
<<
Move joystick left &right to choose
<<
Move joystick left &right to Exit
<<
Move joystick left &right to enter
<<
Move joystick left &right to enter
STORED
IRIS CLOSE WHEN DONE
2. END POINTER
<<
Move joystick left &right to enter
STORED
IRIS CLOSE WHEN DONE
3. SCAN SPEED
3
NOTE: SCAN SPEED
4. DIRECTION
<<
Move joystick left &right to choose
1----7
S-CIRCLE/ L-CIRCLE
<<
Move joystick left &right to choose
5. RUN
<<
Move joystick left &right to choose
6. RETURN
<<
Move joystick left &right to Exit
52
HD-AHD Intelligent High Speed Dome User Manual
6. AUTO SCAN SETUP
1. AUTO SCAN POS SET
<<
Move joystick left &right to choose
<<
Move joystick left &right to choose
<<
Move joystick left &right to choose
STORED
IRIS CLOSE WHEN DONE
2. SCAN SPEED
3
NOTE: SCAN SPEED
3. DIRECTION
1----7
LEFT/RIGHT
4. RUN
<<
Move joystick left &right to choose
<<
Move joystick left &right to enter
5. RETIRN
<<
Move joystick left &right Exit
<<
Move joystick left &right to enter
7. IRLED CONTROL
1. IRLED MODE
2. THRESHOLD
AUTO /OFF/ON
10
<<
Move joystick left &right to choose
Time Delay (Seconds) <<
Move joystick left &right to enter
NOTE: 3---60S
3. SENSITVITY
5
NOTE: SENSITVITY
4. RETURN
8. RETURN
7. EXIT
<<
Move joystick left &right to choose
<<
Move joystick left &right to Exit
<<
Move joystick left &right to Exit
1----8
<<
Note: This Privacy Mask in only avaible for Samsung camera module.
53
Move joystick left &right to Exit
HD-AHD Intelligent High Speed Dome User Manual
Appendix 1 Lightning and surge protection
Appendix 2
RS485 Bus Connection
Appendix 3
FAQs and solutions
54
HD-AHD Intelligent High Speed Dome User Manual
Appendix 1 Lighting and surge protection
This product adopts TVS plate lightning protection technology to avoid damage caused by pulse signal that
is below 3000W, like instantaneous lighting, surging, etc. According to the actual situation outdoors, necessary
protection measures must be taken to secure the electrical safety.
1. The distance between signal transmission line and High-voltage equipment or high-voltage cable is at
least 50m.
2. Outdoor wiring should better be along the eaves as much as possible.
3 In the open field, wiring should be buried underground in sealed steel pipe, and the steel-pipe should be
one-point grounding. Overhead routing method is forbidden.
4. In strong thunderstorm area or high induction voltage areas (such as high-voltage transformer substation),
high power lightning protection apparatus and lightning conductor are necessary to be appended.
5. The design for installation and wiring with lightning protection and grounding in mind should be
combined with the lightning protection consideration of the building, and conform to the related national
standards and industry standards.
6. The system should be equipotentially grounded, and the grounding equipment must satisfy
double-request of system anti-jamming and electric safety, and it must not appear short circuit and open circuit
with the zero conductor of strong grid. When the system is grounding individual, the resistance should be no
2
more than 4Ω, the section al area of the grounding cable should be no less than 25mm .
Appendix 2
RS485 Bus Connection
1. General Property of RS485 Bus
According to RS485 industry bus standard, RS485 is a half-duplex communication bus which has 120Ω
characteristic impendence, the maximum load ability is 32 payloads (including controller device and controlled
device).
2. RS485 Bus Transmission Distance
When using 0.75mm (24AWG) twisted-pair line, according to different baud rate, the max transmission
distance theory table is shown as below:
Baud Rate
Max Distance
2400BPS
1800m
4800BPS
1200m
9600BPS
800m
55
HD-AHD Intelligent High Speed Dome User Manual
The transmission distance will be decreased if we use the thinner cable, or use this product under the strong
electromagnetic interference situation, or there are lots of devices are added to the bus; on the contrary, the
transmission distance will be increased.
3. Connection Method and Terminal Resistance
1) RS485 industry bus standard require daisy-chain connection method between any devices, both sides have to
connect a 120Ω terminal resistance
2) Connection of 120Ω terminal resistor
The 120Ω terminal resistor can be connected through the DIP switch on the communications board
4. Problems in the Practical Application
Normally, users adopt star-shape connection method in construction, under this situation, the terminal resistors
must be connected between two farthest devices. But this connection method is not satisfy the requirement of the
RS485 industry standard so that it will lead to some problems such as signal reflection, anti-jamming ability
decline when the devices are faraway. At this time, the dome will be uncontrollable, or self-running, etc.
For such case, the best way is adding a RS485 distributor. This product can effectively change the star-shape
connection to which satisfies the requirement of RS485 industry standard, in order to avoid those problems and
improve the communication reliability.
56
HD-AHD Intelligent High Speed Dome User Manual
Appendix 3
No
1
2
3
4
FAQ and solutions
Phenomenon
No response after
power-up, motors
no locked, no
display,
Dome rotates
normally when
start, without word
or no image
OSD menu can
display after
self-check
Text or image
distorted, flopping
or garbled
5
No self-chek after
start, but motors
can be locked
6
Mistake in pan
rotatin during
self-checking
Possible causes
Solutions
Not connected do power
Check power connection
DC12V
Problem with power board
Change power board
Slipping cable was
disconnected
Problem with master
control board
Change slipping
Remark
Please strictly
follow the conection
method of one-dome
wiring
Change master control
board
Swith of word display was
OFF
Turn on the Swith of
word display
Bad connection between
camera module and dome
Change a new FPC
cable( between camera
module and dome) or a
camera module
Wrong operation
95+ PREVIEW to
display OSD menu
Problem with main
control board
Change main control
board
Signal was interferced, or
the camera was targeting
at electronic image
Connect dome to ground
or turn off surrounding
electronic equipment
(electrical, high-frequent
equipment, signal
generator),rotate the
camera module
Confusion in system
Restard the dome
System is set to do
self-checking after getting
commucation signal
Pan baffle not in right
position
Pan belt is not tight
enough
Connect keyboard
controller, set the right
protocol, baud rate and
dome address
Adjust position of
photoelectricity switch
Adjust position of pan
motor
57
Within 45 seconds
after restart
After self-check,
OSD menu can only
display when there
is image
There must be
shielding line on the
video line
There will be text
dislayif it’s normal
The pan baffle
should be in the 2/3
of the central trough
of Photoelectric
switch
HD-AHD Intelligent High Speed Dome User Manual
It’s innormal if it
happens very
often,adjust the pan
baffle or check if the
mechanical parts are
too tight
7
After dome works
normally, dome
will rotate 360
degree when
controlled,
Dome is doing
self-correcting
Normal
8
Tilt isnot within 0
degree---90
degree
Mistake in tilt positioning,
camera may be baffled by
something and thus start
position too early
Check and readjust
mechanical installation
Normal
seld-cheking,can
be controlled
Wrong setting
9
Reset protocol, baud rate,
address
RS485 not connect well
Check connection
Communicate distance too
long
Add driver
10
11
12
13
Dome not respond
good to keyboard
Dome run the
wrong function
when it’s called
Dome work
automcially after a
certain period of
time
Same operation
works for one
dome, but not
work with the
other
RS485 not connect well
Check wring
Usually it’s the
problem with the
coonection
Slipping damaged
Change slipping
RS-485 protecting pipe
damaged
RS-485 protecting pipe
Mistake or disturbution
in system
Restart dome
Dome is set to call a
function when there is no
communication
Cancel this setting
Problem in setting or
connection
re-est or check
connection
Note: The cables may differ by different manufacture even with same model name, the above table is for
reference of common cable.
RPTZ1080-10X-E-0-001
58
Download PDF
Similar pages