Motherboard
Q270M-CM-A
Q270M-CM-A/CSM PRO
E13587
Revised Edition v2
Oct. 2017
Copyright © 2017 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any
means, except documentation kept by the purchaser for backup purposes, without the express written
permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless
such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),
EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY
DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,
AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO
RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS
MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identification or explanation and to the
owners’ benefit, without intent to infringe.
Offer to Provide Source Code of Certain Software
This product contains copyrighted software that is licensed under the General Public License (“GPL”),
under the Lesser General Public License Version (“LGPL”) and/or other Free Open Source Software
Licenses. Such software in this product is distributed without any warranty to the extent permitted by the
applicable law. Copies of these licenses are included in this product.
Where the applicable license entitles you to the source code of such software and/or other additional data,
you may obtain it for a period of three years after our last shipment of the product, either
(1) for free by downloading it from http://support.asus.com/download
or
(2) for the cost of reproduction and shipment, which is dependent on the preferred carrier and the location
where you want to have it shipped to, by sending a request to:
ASUSTeK Computer Inc.
Legal Compliance Dept.
15 Li Te Rd.,
Beitou, Taipei 112
Taiwan
In your request please provide the name, model number and version, as stated in the About Box of the
product for which you wish to obtain the corresponding source code and your contact details so that we
can coordinate the terms and cost of shipment with you.
The source code will be distributed WITHOUT ANY WARRANTY and licensed under the same license as
the corresponding binary/object code.
This offer is valid to anyone in receipt of this information.
ASUSTeK is eager to duly provide complete source code as required under various Free Open Source
Software licenses. If however you encounter any problems in obtaining the full corresponding source
code we would be much obliged if you give us a notification to the email address gpl@asus.com, stating
the product and describing the problem (please DO NOT send large attachments such as source code
archives, etc. to this email address).
ii
Contents
Safety information....................................................................................... iv
About this guide.......................................................................................... iv
Package contents........................................................................................ vi
Q270M-CM-A specifications summary...................................................... vi
Chapter 1:
Product introduction
Motherboard overview.............................................................................. 1-1
Central Processing Unit (CPU)................................................................. 1-8
System memory......................................................................................... 1-9
Chapter 2:
BIOS information
BIOS setup program.................................................................................. 2-1
BIOS menu screen..................................................................................... 2-2
Exit menu.................................................................................................... 2-3
Appendix
Notices........................................................................................................A-1
ASUS contact information........................................................................A-5
iii
Safety information
Electrical safety
•
To prevent electrical shock hazard, disconnect the power cable from the electrical outlet
before relocating the system.
•
When adding or removing devices to or from the system, ensure that the power cables
for the devices are unplugged before the signal cables are connected. If possible,
disconnect all power cables from the existing system before you add a device.
•
Before connecting or removing signal cables from the motherboard, ensure that all power
cables are unplugged.
•
Seek professional assistance before using an adapter or extension cord. These devices
could interrupt the grounding circuit.
•
Ensure that your power supply is set to the correct voltage in your area. If you are not
sure about the voltage of the electrical outlet you are using, contact your local power
company.
•
If the power supply is broken, do not try to fix it by yourself. Contact a qualified service
technician or your retailer.
Operation safety
•
Before installing the motherboard and adding components, carefully read all the manuals
that came with the package.
•
Before using the product, ensure all cables are correctly connected and the power cables
are not damaged. If you detect any damage, contact your dealer immediately.
•
To avoid short circuits, keep paper clips, screws, and staples away from connectors,
slots, sockets and circuitry.
•
Avoid dust, humidity, and temperature extremes. Do not place the product in any area
where it may be exposed to moisture.
•
Place the product on a stable surface.
•
If you encounter technical problems with the product, contact a qualified service
technician or your retailer.
About this guide
This user guide contains the information you need when installing and configuring the
motherboard.
How this guide is organized
This guide contains the following parts:
•
Chapter 1: Product introduction
This chapter describes the features of the motherboard and the new technology it
supports. It includes descriptions of the switches, jumpers, and connectors on the
motherboard.
•
Chapter 2: BIOS information
This chapter discusses changing system settings through the BIOS Setup menus.
Detailed descriptions fo the BIOS parameters are also provided.
iv
Where to find more information
Refer to the following sources for additional information and for product and software
updates.
1.
ASUS websites
The ASUS website provides updated information on ASUS hardware and software
products. Refer to the ASUS contact information.
2.
Optional documentation
Your product package may include optional documentation, such as warranty flyers,
that may have been added by your dealer. These documents are not part of the
standard package.
Conventions used in this guide
To ensure that you perform certain tasks properly, take note of the following symbols used
throughout this manual.
DANGER/WARNING: Information to prevent injury to yourself when
completing a task.
CAUTION: Information to prevent damage to the components when
completing a task
IMPORTANT: Instructions that you MUST follow to complete a
task.
NOTE: Tips and additional information to help you complete a task.
Typography
Bold text
Indicates a menu or an item to select.
Italics
Used to emphasize a word or a phrase.
<Key>
Keys enclosed in the less-than and greater-than sign
means that you must press the enclosed key.
Example: <Enter> means that you must press the Enter or
Return key.
<Key1> + <Key2> + <Key3>
If you must press two or more keys simultaneously, the key
names are linked with a plus sign (+).
v
Package contents
Check your motherboard package for the following items.
Motherboard
ASUS Q270M-CM-A motherboard
Cables
2 x Serial ATA 6.0 Gb/s cables
Accessories
1 x I/O Shield
1 x M.2 screw package
Application DVD
Support DVD
Documentation
User Guide
If any of the above items is damaged or missing, contact your retailer.
Q270M-CM-A specifications summary
CPU
LGA1151 socket for 7th/6th Generation Intel® Core™ i7/ i5/ i3, Pentium®,
and Celeron® Processors*
Supports 14nm CPU
Supports Intel® Turbo Boost Technology 2.0**
* The Intel® Turbo Boost Technology 2.0 support depends on the CPU types.
**Refer to www.asus.com for Intel® CPU support list.
Chipset
Intel® Q270 Chipset
Memory
4 x DIMM, max. 64GB, DDR4 2400MHz, non-ECC, un-buffered memory
Dual-channel memory architecture
Supports Intel® Extreme Memory Profile (XMP)
* Hyper DIMM support is subject to the physical characteristics of individual
CPUs. Please refer to Memory QVL for details.
** Refer to www.asus.com for the latest Memory QVL (Qualified Vendors List).
Graphics
Integrated graphics processor
Multi-VGA output support: 2xDP/HDMI/RGB ports
- Supports DisplayPort with max. resolution of 4096 x 2304 @60Hz
- Supports HDMI with max. resolution of 4096x2160@24Hz /
2560x1600@60Hz
- Supports RGB with max. resolution of 1920 x 1200 @60Hz
Support up to three displays simultaneously
Support Intel® InTruTM 3D, Quick Sync Video, Intel® Clear Video HD
Technology, and Intel® InsiderTM
Maximum shared memory of 1024 MB
Expansion slots
2 x PCI Express 3.0/2.0 x16 slots (1@x4 mode)
2 x PCI Express 3.0/2.0 x1 slots
LAN
Intel® I219LM Gigabit LAN Controller
Audio
Realtek ALC887 8-channel High Definition Audio CODEC
- Supports jack-detection and front panel jack-retasking
USB
8 x USB 3.0 ports Type A (2 ports at midboard, 6 ports at back panel)
1 x USB 3.0 port Type C (1 ports at back panel)
2 x USB 2.0 ports (2 ports at midboard)
(continued on the next page)
vi
Q270M-CM-A specifications summary
Storage
Intel® Q270 Chipset:
- 6 x Serial ATA 6.0 Gb/s connectors (gray)
- 2 x M.2 Sockets with M Key, type 2242/2260/2280 storage devices
with IRST support, (M.1_1 @ SATA & PCIE x4 mode, M.2_2 @PCIE
x2 mode)
- Ready for Intel® Optane Memory*
- Supports Raid 0,1,5,10
*Intel® Optane Technology is only supported when using 7th Generation Intel®
Processors. Before using Intel® Optane memory modules, ensure that you
have updated your motherboard drivers and BIOS to the latest version from
ASUS support website.
Dependable stability:
ASUS 5X PROTECTION III:
- SafeSlot Core - Fortified PCIe with solid soldering
- LANGuard - Surge-protected networking
- Overvoltage Protection - World-class circuit-protecting power design
- ESD Guards - Electrostatic discharge protection
- Stainless Steel Back I/O - 3X corrosion-resistance for greater
durability
ASUS unique features
Superb performance:
UEFI BIOS:
- Most advanced options with fast response time
Easy PC DIY:
Safe motherboard mounting
- Component-free areas to minimize damage risk
Q-Design
- ASUS Q-DIMM
- ASUS Q-Slot
1 x PS/2 keyboard port (purple)
1 x PS/2 mouse port (green)
1 x D-Sub port
1 x HDMI port
Rear panel I/O ports
2 x DisplayPorts
1 x LAN (RJ-45) port
6 x USB 3.0/2.0 Type A ports
1 x USB 3.0/2.0 Type C port
3 x Audio jacks support 8-channel audio output*
* Use a chassis with HD audio module in the front panel to support an
8-channel audio output.
1 x USB 3.0/2.0 connector supports additional 2 USB 3.0 ports
1 x USB 2.0/1.1 connector supports additional 2 USB 2.0 ports
Internal connectors/
switches/ buttons
6 x SATA 6Gb/s connector
1 x CPU Fan connector
2 x Chassis Fan connectors
1 x Front panel audio connector(s) (AAFP)
1 x System panel connector
(continued on the next page)
vii
Q270M-CM-A specifications summary
Internal
connectors/
switches/
buttons
1 x 24-pin ATX Power connector
1 x 8-pin ATX 12V Power connector
1 x Speaker connector
2 x COM port header
1 x LPT port header
1 x Chassis Intrusion header
1 x Clear CMOS header
1 x MONO-out header(with Amp IC)
1 x DIS ME jumper
1 x LPC debug header
TPM 2.0 IC Onboard
BIOS features
64 Mb Flash ROM, UEFI AMI BIOS, PnP, DMI3.0, WfM2.0, SM BIOS 3.0,
ACPI 5.1, Multi-language BIOS, ASUSbackup, LOGO flash, ME update, DMI
value edit, BIOS value edit
Manageability
WfM 2.0, DMI 3.0, WOL, WOR, PXE
Support DVD
Drivers
Operating
systems
Windows® 10 (64-bit)
Windows® 8.1 (64-bit)*
Windows® 7 (64-bit/32-bit)*
*Windows® 8.1 (64-bit) and Windows® 7 (32/64-bit) are only supported when using
6th Generation Intel® Processors.
Form factor
mATX Form Factor 9.6 x 9.6 inches (24.4 x 24.4 cm)
Specifications are subject to change without notice.
viii
1
Product introduction
Motherboard overview
•
Unplug the power cord from the wall socket before touching any component.
•
Before handling components, use a grounded wrist strap or touch a safely grounded
object or a metal object, such as the power supply case, to avoid damaging them due
to static electricity.
•
Before you install or remove any component, ensure that the ATX power supply is
switched off or the power cord is detached from the power supply. Failure to do so
may cause severe damage to the motherboard, peripherals, or components.
•
Unplug the power cord before installing or removing the motherboard. Failure to do so
can cause you physical injury and damage to motherboard components.
1
2
3
1
4
5
24.4cm(9.6in)
KBMS
CPU_FAN
DIGI
+VRM
2242
LAN1_USB3_910
M.2_1(SOCKET3)
AUDIO
CHA_FAN1
16
18
17
Super
I/O
ALC
122
PCIEX1_2
2280
2260
2242
Intel®
Q270
PCIE SATA
X2
X
LPC_DEBUG
IRST
V
64Mb
BIOS
PCIEX16_2
16
COM1
AAFP
COM2
USB1112
LPT
EATXPWR
24.4cm(9.6in)
1
5
14
13
12
11
6
SATA6G_6 SATA6G_5
SPEAKER
CLRTC CHASSIS
DIS_ME
15
7
BATTERY
PCIEX1_1
MONO_OUT
IRST
V
6
SATA6G_4 SATA6G_3
I219LM
ALC
887
M.2_2(SOCKET3)
19
PCIE SATA
X4
V
PCIEX16_1
SATA6G_2 SATA6G_1
2260
1
2
USB3_12
2280
CHA_FAN2
DDR4 DIMM_B2 (64bit, 288-pin module)
USB3_5-8
DDR4 DIMM_B1 (64bit, 288-pin module)
LGA1151
USB3_C5
DDR4 DIMM_A2 (64bit,288-pin module)
DDR4 DIMM_A1 (64bit, 288-pin module)
Place this
side towards
the rear of the
chassis
EATX12V
VGA
HDMI
DP12
10 9
F_PANEL
8
Scan the QR code to get the detailed pin definitions.
ASUS Q270M-CM-A
1-1
CPU and chassis fan connectors (4-pin CPU_FAN, 4-pin CHA_FAN1/2)
Connect the fan cables to the fan connectors on the motherboard, ensuring that the
black wire of each cable matches the ground pin of the connector.
Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside
the system may damage the motherboard components. These are not jumpers! Do not
place jumper caps on the fan connectors! The CPU_FAN connector supports a CPU fan
of maximum 1A (12 W) fan power.
ATX power connectors (24-pin EATXPWR, 8-pin ATX12V)
Correctly orient the ATX power supply plugs into these connectors and push down
firmly until the connectors completely fit.
•
For a fully configured system, we recommend that you use a power supply
unit (PSU) that complies with ATX 12 V Specification 2.0 (or later version)
and provides a minimum power of 350 W.
•
If you are uncertain about the minimum power supply requirement for your
system, refer to the Recommended Power Supply Wattage Calculator
at http://support.asus.com/PowerSupplyCalculator/PSCalculator.
aspx?SLanguage=en-us for details.
Intel® LGA1151 CPU socket
Install Intel® LGA1151 CPU into this surface mount LGA1151 socket, which is
designed for 7th / 6th Generation Intel® Core™ i7 / i5 / i3, Pentium®, and Celeron®
processors.
For more details, refer to Central Processing Unit (CPU).
DDR4 DIMM slots
This motherboard comes with four Double Data Rate 4 (DDR4) Dual Inline Memory
Module (DIMM) sockets. A DDR4 module is notched differently from a DDR, DDR2,
or DDR3 module.
For more details, refer to System memory.
DO NOT install a DDR, DDR2, or DDR3 memory module to the DDR4 slot.
M.2 socket 3
These sockets allow you to install an M.2 (NGFF) SSD module.
These sockets support M Key and 2242/2260/2280 storage devices.
1-2
Chapter 1: Product introduction
Intel® Q270 Serial ATA 6.0Gb/s connectors (7-pin SATA6G_1~6)
These connectors connect to Serial ATA 6.0 Gb/s hard disk drives via Serial ATA
6.0 Gb/s signal cables.
When using hot-plug and NCQ, set the SATA Mode Selection item in the BIOS to
[AHCI]. USB 3.0 connector (20-1 pin USB3_12)
Connect a USB 3.0 module to this connector for additional USB 3.0 front or rear
panel ports. This connector complies with USB 3.0 specifications and provide
faster data transfer speeds of up to 5 Gbps, faster charging time for USBchargeable devices, optimized power efficiency, and backward compatibility with
USB 2.0.
System panel connector (10-1 pin F_PANEL)
This connector supports several chassis-mounted functions.
Speaker connector (4-pin SPEAKER)
The 4-pin connector is for the chassis-mounted system warning speaker. The
speaker allows you to hear system warnings.
Clear RTC RAM (2-pin CLRTC)
This header allows you to unconfigure ME and clear the CMOS RTC RAM data of
the system setup information such as date, time, and system passwords.
To erase the RTC RAM:
1.
Turn OFF the computer and unplug the power cord.
2.
Use a metal object such as a screwdriver to short the two pins.
3.
Plug the power cord and turn ON the computer.
4.
Hold down the <Del> key during the boot process and enter BIOS setup to
re-enter data.
If the steps above do not help, remove the onboard battery and short the
two pins again to clear the CMOS RTC RAM data. After clearing the CMOS,
reinstall the battery.
LPT connector (26-1 pin LPT)
The LPT (Line Printing Terminal) connector supports devices such as a printer.
LPT standardizes as IEEE 1284, which is the parallel port interface on IBM PCcompatible computers.
Intel® ME jumper (3-pin DIS_ME)
This jumper allows you to enable or disable the Intel® ME function. Set this jumper
to pins 1-2 to enable (default) the Intel® ME function and to pins 2-3 to disable it.
Disable the Intel® ME function before updating it.
ASUS Q270M-CM-A
1-3
USB 2.0 connector (10-1 pin USB1112)
This connector is for USB 2.0 ports. Connect the USB module cable to this
connector, then install the module to a slot opening at the back of the system
chassis. This USB connector complies with USB 2.0 specifications and supports
up to 480Mbps connection speed.
Serial port connectors (10-1 pin COM1~2)
These connectors are for serial (COM) ports. Connect the serial port module cable
to any of these connectors, then install the module to a slot opening at the back of
the system chassis.
Front panel audio connector (10-1 pin AAFP)
This connector is for a chassis-mounted front panel audio I/O module that supports HD Audio standard. Connect one end of the front panel audio I/O module cable to
this connector.
We recommend that you connect a high-definition front panel audio module to
this connector to avail of the motherboard’s high-definition audio capability.
PCI Express 3.0/2.0 x16 slots
This motherboard has PCI Express 3.0/2.0 x16 slots that support PCI Express
3.0/2.0 x16 graphic cards complying with the PCI Express specifications.
This header allows connection to a LPC
debug card.
LPC_DEBUG
+3V
+3V
CK_33M_LPC
GND
LPC Debug header
PIN 1
S_LAD0
S_LAD1
S_LAD2
S_LAD3
S_LFRAME#
USB1112
Mono out header (2-pin MONO_OUT)
This internal mono out header allows connection to an internal, low power speaker
for basic system sound capability. The subsystem is capable of driving a speaker
load of 2 Ohms at 2 Watts (rms).
PCI Express 3.0/2.0 x1 slots
This motherboard supports two PCI Express x1 network cards, SCSI cards, and
other cards that comply with the PCI Express specifications.
1-4
Chapter 1: Product introduction
IRQ assignments for this motherboard
HD Audio Controller
XHCI Controller
SATA Controller
LAN1 I219LM
PCIEx1_1
PCIEx1_2
A
shared
shared
shared
shared
–
–
B
–
–
–
–
–
–
C
–
–
–
–
shared
–
D
–
–
–
–
–
shared
PCIEx16_1
shared
–
–
–
PCIEx16_1
shared
–
–
–
M.2_1
shared
–
–
–
When using PCI cards on shared slots, ensure that the drivers support “Share IRQ” or that
the cards do not need IRQ assignments. Otherwise, conflicts will arise between the two PCI
groups, making the system unstable and the card inoperable.
ASUS Q270M-CM-A
1-5
Rear panel connectors
1
2
11
1.
3
10
4
9
5
6
4
8
7
PS/2 mouse port (green). This port is for a PS/2 mouse.
2.DisplayPorts. These ports are for DisplayPort-compatible devices.
3.
Video Graphics Adapter (VGA) port. This 15-pin port is for a VGA monitor or other
VGA-compatible devices.
4.
USB 3.0 ports. These 9-pin Universal Serial Bus (USB) ports are for USB 3.0/2.0
devices.
•
USB 3.0 devices can only be used for data storage.
•
We strongly recommend that you connect USB 3.0 devices to USB 3.0 ports for faster
and better performance from your USB 3.0 devices.
•
Due to the design of the Intel® 200 series chipset, all USB devices connected to the
USB 2.0 and USB 3.0 ports are controlled by the xHCI controller. Some legacy USB
devices must update their firmware for better compatibility.
5.
LAN (RJ-45) port. This port allows Gigabit connection to a Local Area Network (LAN)
through a network hub.
LAN port LED indications
Activity/Link LED
Status
Off
Orange
Orange (Blinking)
Orange (Blinking
then steady)
1-6
Description
No link
Linked
Data activity
Ready to wake up
from S5 mode
Speed LED
Status
OFF
ORANGE
GREEN
_
Description
10Mbps connection
100Mbps connection
1Gbps connection
_
Chapter 1: Product introduction
6.
Line In port (light blue). This port connects to the tape, CD, DVD player, or other
audio sources.
7.
Line Out port (lime). This port connects to a headphone or a speaker. In the 4.1, 5.1
and 7.1-channel configurations, the function of this port becomes Front Speaker Out.
8.
Microphone port (pink). This port connects to a microphone.
Refer to the audio configuration table for the function of the audio ports in 2.1, 4.1, 5.1, or
7.1-channel configuration.
Audio 2.1, 4.1, 5.1, or 7.1-channel configuration
Headset
2.1-channel
Port
Light Blue (Rear
panel)
Lime (Rear panel)
Pink (Rear panel)
Lime (Front panel)
9.
4.1-channel
5.1-channel
7.1-channel
Line In
Rear Speaker Out
Rear Speaker Out
Rear Speaker Out
Line Out
Mic In
-
Front Speaker Out
Mic In
-
Front Speaker Out
Bass/Center
-
Front Speaker Out
Bass/Center
Side Speaker Out
5Gb/s Type C USB port. This Universal Serial Bus (USB) Type C port is for Type C
USB mobile or peripheral devices.
10. HDMI port. This port is for a High-Definition Multimedia Interface (HDMI) connector,
and is HDCP compliant allowing playback of HD DVD, Blu-ray, and other protected
content.
11. PS/2 keyboard port (purple). This port is for a PS/2 keyboard.
ASUS Q270M-CM-A
1-7
Central Processing Unit (CPU)
This motherboard comes with a surface mount LGA1151 socket
designed for 7th / 6th Generation Intel® Core™ i7 / i5 / i3, Pentium®, and
Celeron® processors.
Unplug all power cables before installing the CPU.
•
Ensure that you install the correct CPU designed for the LGA1151 socket only. DO
NOT install a CPU designed for LGA1150, LGA1155 and LGA1156 sockets on the
LGA1151 socket.
•
Upon purchase of the motherboard, ensure that the PnP cap is on the socket and
the socket contacts are not bent. Contact your retailer immediately if the PnP cap
is missing, or if you see any damage to the PnP cap/socket contacts/motherboard
components.
•
Keep the cap after installing the motherboard. ASUS will process Return Merchandise
Authorization (RMA) requests only if the motherboard comes with the cap on the
LGA1151 socket.
•
The product warranty does not cover damage to the socket contacts resulting from
incorrect CPU installation/removal, or misplacement/loss/incorrect removal of the PnP
cap.
Installing the CPU
1
A
B
4
2
A
4
C
3
5
D5
B
4
Apply the Thermal Interface Material to the CPU heatsink and CPU before you install the
heatsink and fan if necessary.
1-8
Chapter 1: Product introduction
System memory
Overview
This motherboard comes with four Double Data Rate 4 (DDR4) Dual Inline Memory Module
(DIMM) sockets. A DDR4 module is notched differently from a DDR, DDR2, or DDR3 module.
DO NOT install a DDR, DDR2, or DDR3 memory module to the DDR4 slot.
DIMM_A1
DIMM_A2
DIMM_B1
DIMM_B2
Channel
Channel A
Channel B
Sockets
DIMM_A1 & DIMM_A2
DIMM_B1 & DIMM_B2
•
You may install varying memory sizes in Channel A and Channel B. The system
maps the total size of the lower-sized channel for the dual-channel configuration. Any
excess memory from the higher-sized channel is then mapped for single-channel
operation.
•
Always install the DIMMS with the same CAS Latency. For an optimum compatibility,
we recommend that you install memory modules of the same version or data code
(D/C) from the same vendor. Check with the vendor to get the correct memory
modules.
•
According to Intel® CPU spec, DIMM voltage below 1.35V is recommended to protect
the CPU.
•
Due to the memory address limitation on 32-bit Windows® OS, when you install 4GB
or more memory on the motherboard, the actual usable memory for the OS can be
about 3GB or less. For effective use of memory, we recommend that you do any of the
following:
-
Use a maximum of 3 GB system memory if you are using a 32-bit Windows® OS.
-
Install a 64-bit Windows® OS if you want to install 4GB or more on the
motherboard.
-
For more details, refer to the Microsoft® support site at http://support.microsoft.
com/kb/929605/en-us.
Visit the ASUS website at www.asus.com for the latest QVL.
Recommended memory configurations
ASUS Q270M-CM-A
1-9
Installing a DIMM
1
2
A
A
B
To remove a DIMM
A
B
1-10
Chapter 1: Product introduction
2
BIOS information
Scan the QR code to view the BIOS update guide.
BIOS setup program
Use the BIOS Setup program to update the BIOS or configure its
parameters. The BIOS screens include navigation keys and brief online
help to guide you in using the BIOS Setup program.
Entering BIOS Setup at startup
To enter BIOS Setup at startup:
Press <Delete> or <F2> during the Power-On Self Test (POST). If you do not press <Delete>
or <F2>, POST continues with its routines.
Entering BIOS Setup after POST
To enter BIOS Setup after POST:
•
Press <Ctrl>+<Alt>+<Del> simultaneously.
•
Press the reset button on the system chassis.
•
Press the power button to turn the system off then back on. Do this option only if you
failed to enter BIOS Setup using the first two options.
Using the power button, reset button, or the <Ctrl>+<Alt>+<Del> keys to force reset from a
running operating system can cause damage to your data or system. We recommend you
always shut down the system properly from the operating system.
2-1
•
The BIOS setup screens shown in this section are for reference purposes only, and
may not exactly match what you see on your screen.
•
Visit the ASUS website at www.asus.com to download the latest BIOS file for this
motherboard.
•
If the system becomes unstable after changing any BIOS setting, load the default
settings to ensure system compatibility and stability. Select the Load Optimized
Defaults item under the Exit menu or press hotkey F5.
•
If the system fails to boot after changing any BIOS setting, try to clear the CMOS and
reset the motherboard to the default value. See section Motherboard overview for
information on how to erase the RTC RAM.
ASUS Q270M-CM-A
BIOS menu screen
General Help
Menu bar
Main
Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc.
Ai Tweaker Advanced Monitor Boot Tool
Exit
BIOS Information
BIOS Version
Build Date
ME Firmware Version
PCH Stepping
0206 x64
01/23/2017
11.6.0.1126
AO
Processor Information
Brand String
CPU Speed
Total Memory
Memory Frequency
Intel(R)Core(TM)
i3-6300 CPU @ 3.80GHz
3800 MHz
8192 MB
2133 MHz
System Language
[English]
System Date
System Time
[Sun 07/23/2017]
[14:44:55]
Access Level
Security
Administrator
Choose the default
language
: Select Screen
: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.17.1246 Copyright (C) 2017 American Megatrends, Inc.
Sub-menu item
Chapter 2: BIOS information
Menu items
Configuration fields
2-2
Exit menu
The Exit menu items allow you to load the optimal default values for the BIOS items, and
save or discard your changes to the BIOS items.
Main
Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc.
Ai Tweaker
Advanced
Monitor
Boot
Tool
Exit
Load Optimized Defaults
Save Changes & Reset
Discard Changes & Exit
Launch EFI Shell from USB drives
Exit system setup without
saving any changes.
:Select Screen
: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.17.1246 Copyright (C) 2017 American Megatrends, Inc.
Load Optimized Defaults
This option allows you to load the default values for each of the parameters on the Setup
menus. When you select this option or if you press <F5>, a confirmation window appears.
Select OK to load the default values.
Save Changes & Reset
Once you are finished making your selections, choose this option from the Exit menu to
ensure the values you selected are saved. When you select this option or if you press <F10>,
a confirmation window appears. Select OK to save changes and exit.
Discard Changes & Exit
This option allows you to exit the Setup program without saving your changes. When you
select this option or if you press <Esc>, a confirmation window appears. Select OK to discard
changes and exit.
Launch EFI Shell from USB drives
This option allows you to attempt to launch the EFI Shell application (shellx64.efi) from one of
the available USB devices.
2-3
ASUS Q270M-CM-A
Chapter 2: BIOS information
2-4
Appendix
Q-Code table
Code
00
01
02
03
04
06
Description
Not used
Power on. Reset type detection (soft/hard).
AP initialization before microcode loading
System Agent initialization before microcode loading
PCH initialization before microcode loading
Microcode loading
07
AP initialization after microcode loading
08
09
0B
0C – 0D
0E
0F
10
11 – 14
15 – 18
19 – 1C
2B – 2F
30
31
32 – 36
37 – 3A
3B – 3E
4F
System Agent initialization after microcode loading
PCH initialization after microcode loading
Cache initialization
Reserved for future AMI SEC error codes
Microcode not found
Microcode not loaded
PEI Core is started
Pre-memory CPU initialization is started
Pre-memory System Agent initialization is started
Pre-memory PCH initialization is started
Memory initialization
Reserved for ASL (see ASL Status Codes section below)
Memory Installed
CPU post-memory initialization
Post-Memory System Agent initialization is started
Post-Memory PCH initialization is started
DXE IPL is started
Memory initialization error. Invalid memory type or incompatible memory
speed
Unspecified memory initialization error
Memory not installed
Invalid CPU type or Speed
CPU mismatch
CPU self test failed or possible CPU cache error
CPU micro-code is not found or micro-code update is failed
Internal CPU error
Reset PPI is not available
Reserved for future AMI error codes
50 – 53
54
55
56
57
58
59
5A
5B
5C – 5F
(continued on the next page)
ASUS Q270M-CM-A
A-1
Q-Code table
Code
E0
E1
E2
E3
E4 – E7
E8
E9
EA
EB
EC – EF
F0
F1
F2
F3
F4
F5 – F7
F8
F9
FA
FB – FF
60
61
62
63 – 67
68
69
Description
S3 Resume is stared (S3 Resume PPI is called by the DXE IPL)
S3 Boot Script execution
Video repost
OS S3 wake vector call
Reserved for future AMI progress codes
S3 Resume Failed
S3 Resume PPI not Found
S3 Resume Boot Script Error
S3 OS Wake Error
Reserved for future AMI error codes
Recovery condition triggered by firmware (Auto recovery)
Recovery condition triggered by user (Forced recovery)
Recovery process started
Recovery firmware image is found
Recovery firmware image is loaded
Reserved for future AMI progress codes
Recovery PPI is not available
Recovery capsule is not found
Invalid recovery capsule
Reserved for future AMI error codes
DXE Core is started
NVRAM initialization
Installation of the PCH Runtime Services
CPU DXE initialization is started
PCI host bridge initialization
System Agent DXE initialization is started
6A
System Agent DXE SMM initialization is started
6B – 6F
70
71
72
73 – 77
78
79
7A – 7F
System Agent DXE initialization (System Agent module specific)
PCH DXE initialization is started
PCH DXE SMM initialization is started
PCH devices initialization
PCH DXE Initialization (PCH module specific)
ACPI module initialization
CSM initialization
Reserved for future AMI DXE codes
(continued on the next page)
A-2
Appendix
Q-Code table
Code
90
91
92
93
94
95
96
97
98
99
9A
9B
9C
9D
9E – 9F
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
AA
AB
AC
AD
AE
AF
B0
B1
B2
B3
Description
Boot Device Selection (BDS) phase is started
Driver connecting is started
PCI Bus initialization is started
PCI Bus Hot Plug Controller Initialization
PCI Bus Enumeration
PCI Bus Request Resources
PCI Bus Assign Resources
Console Output devices connect
Console input devices connect
Super IO Initialization
USB initialization is started
USB Reset
USB Detect
USB Enable
Reserved for future AMI codes
IDE initialization is started
IDE Reset
IDE Detect
IDE Enable
SCSI initialization is started
SCSI Reset
SCSI Detect
SCSI Enable
Setup Verifying Password
Start of Setup
Reserved for ASL (see ASL Status Codes section below)
Setup Input Wait
Reserved for ASL (see ASL Status Codes section below)
Ready To Boot event
Legacy Boot event
Exit Boot Services event
Runtime Set Virtual Address MAP Begin
Runtime Set Virtual Address MAP End
Legacy Option ROM Initialization
System Reset
(continued on the next page)
ASUS Q270M-CM-A
A-3
Q-Code table
Code
B4
B5
B6
B7
B8– BF
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
DA
DB
DC
Description
USB hot plug
PCI bus hot plug
Clean-up of NVRAM
Configuration Reset (reset of NVRAM settings)
Reserved for future AMI codes
CPU initialization error
System Agent initialization error
PCH initialization error
Some of the Architectural Protocols are not available
PCI resource allocation error. Out of Resources
No Space for Legacy Option ROM
No Console Output Devices are found
No Console Input Devices are found
Invalid password
Error loading Boot Option (LoadImage returned error)
Boot Option is failed (StartImage returned error)
Flash update is failed
Reset protocol is not available
ACPI/ASL Checkpoints (under OS)
Code
03
04
05
30
40
AC
AA
A-4
Description
System is entering S3 sleep state
System is entering S4 sleep state
System is entering S5 sleep state
System is waking up from the S3 sleep state
System is waking up from the S4 sleep state
System has transitioned into ACPI mode. Interrupt controller is in PIC mode.
System has transitioned into ACPI mode. Interrupt controller is in APIC mode.
Appendix
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
•
This device may not cause harmful interference.
•
This device must accept any interference received including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with manufacturer’s instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment to an outlet on a circuit different from that to which the receiver
is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is required
to assure compliance with FCC regulations. Changes or modifications to this unit not
expressly approved by the party responsible for compliance could void the user’s authority
to operate this equipment.
ASUS Q270M-CM-A
A-5
Compliance Statement of Innovation, Science and Economic
Development Canada (ISED)
This Class B digital apparatus complies with Canadian ICES-003, RSS-210, and CAN ICES3(B)/NMB-3(B).
This device complies with Industry Canada license exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired
operation of the device.
Déclaration de conformité de Innovation, Sciences et
Développement économique Canada (ISED)
Cet appareil numérique de classe B est conforme aux normes canadiennes ICES-003, RSS210 et CAN ICES-3(B)/NMB-3(B).
Le présent appareil est conforme aux normes CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. Son utilisation est sujette aux deux conditions suivantes
: (1) cet appareil ne doit pas créer d’interférences et (2) cet appareil doit tolérer tout type
d’interférences, y compris celles susceptibles de provoquer un fonctionnement non souhaité
de l’appareil.
VCCI: Japan Compliance Statement
Class B ITE
KC: Korea Warning Statement
A-6
Appendix
REACH
Complying with the REACH (Registration, Evaluation, Authorisation, and Restriction of
Chemicals) regulatory framework, we published the chemical substances in our products at
ASUS REACH website at http://csr.asus.com/english/REACH.htm.
DO NOT throw the motherboard in municipal waste. This product has been designed to
enable proper reuse of parts and recycling. This symbol of the crossed out wheeled bin
indicates that the product (electrical and electronic equipment) should not be placed in
municipal waste. Check local regulations for disposal of electronic products.
DO NOT throw the mercury-containing button cell battery in municipal waste. This symbol
of the crossed out wheeled bin indicates that the battery should not be placed in municipal
waste.
ASUS Recycling/Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest standards
for protecting our environment. We believe in providing solutions for you to be able to
responsibly recycle our products, batteries, other components as well as the packaging
materials. Please go to http://csr.asus.com/english/Takeback.htm for detailed recycling
information in different regions.
Regional notice for California
WARNING
Cancer and Reproductive Harm www.P65Warnings.ca.gov
Google™ License Terms
Copyright© 2017 Google Inc. All Rights Reserved.
Licensed under the Apache License, Version 2.0 (the “License”); you may not use this file
except in compliance with the License. You may obtain a copy of the License at:
http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software distributed under the
License is distributed on an “AS IS” BASIS, WITHOUT WARRANTIES OR CONDITIONS OF
ANY KIND, either express or implied.
See the License for the specific language governing permissions and limitations under the
License.
ASUS Q270M-CM-A
A-7
English ASUSTeK Computer Inc. hereby declares that this device is in
compliance with the essential requirements and other relevant provisions of
related Directives. Full text of EU declaration of conformity is available at:
www.asus.com/support
Français AsusTek Computer Inc. déclare par la présente que cet appareil est
conforme aux critères essentiels et autres clauses pertinentes des directives
concernées. La déclaration de conformité de l’UE peut être téléchargée à
partir du site Internet suivant : www.asus.com/support
Deutsch ASUSTeK Computer Inc. erklärt hiermit, dass dieses Gerät mit
den wesentlichen Anforderungen und anderen relevanten Bestimmungen
der zugehörigen Richtlinien übereinstimmt. Der gesamte Text der EUKonformitätserklärung ist verfügbar unter: www.asus.com/support
Italiano ASUSTeK Computer Inc. con la presente dichiara che questo
dispositivo è conforme ai requisiti essenziali e alle altre disposizioni pertinenti
con le direttive correlate. Il testo completo della dichiarazione di conformità
UE è disponibile all’indirizzo: www.asus.com/support
Русский Компания ASUS заявляет, что это устройство соответствует
основным требованиям и другим соответствующим условиям
соответствующих директив. Подробную информацию, пожалуйста,
смотрите на www.asus.com/support
Български С настоящото ASUSTeK Computer Inc. декларира, че това
устройство е в съответствие със съществените изисквания и другите
приложими постановления на свързаните директиви. Пълният текст на
декларацията за съответствие на ЕС е достъпна на адрес:
www.asus.com/support
Hrvatski ASUSTeK Computer Inc. ovim izjavljuje da je ovaj uređaj sukladan
s bitnim zahtjevima i ostalim odgovarajućim odredbama vezanih direktiva.
Cijeli tekst EU izjave o sukladnosti dostupan je na: www.asus.com/support
Čeština Společnost ASUSTeK Computer Inc. tímto prohlašuje, že toto
zařízení splňuje základní požadavky a další příslušná ustanovení souvisejících
směrnic. Plné znění prohlášení o shodě EU je k dispozici na adrese:
www.asus.com/support
Dansk ASUSTeK Computer Inc. erklærer hermed, at denne enhed er i
overensstemmelse med hovedkravene og andre relevante bestemmelser i de
relaterede direktiver. Hele EU-overensstemmelseserklæringen kan findes på:
www.asus.com/support
Nederlands ASUSTeK Computer Inc. verklaart hierbij dat dit apparaat
voldoet aan de essentiële vereisten en andere relevante bepalingen van
de verwante richtlijnen. De volledige tekst van de EU-verklaring van
conformiteit is beschikbaar op: www.asus.com/support
Eesti Käesolevaga kinnitab ASUSTeK Computer Inc, et see seade vastab
asjakohaste direktiivide oluliste nõuetele ja teistele asjassepuutuvatele
sätetele. EL vastavusdeklaratsiooni täielik tekst on saadaval järgmisel
aadressil: www.asus.com/support
Suomi ASUSTeK Computer Inc. ilmoittaa täten, että tämä laite on
asiaankuuluvien direktiivien olennaisten vaatimusten ja muiden tätä
koskevien säädösten mukainen. EU-yhdenmukaisuusilmoituksen koko teksti
on luettavissa osoitteessa: www.asus.com/support
Ελληνικά Με το παρόν, η AsusTek Computer Inc. δηλώνει ότι αυτή η
συσκευή συμμορφώνεται με τις θεμελιώδεις απαιτήσεις και άλλες σχετικές
διατάξεις των Οδηγιών της ΕΕ. Το πλήρες κείμενο της δήλωσης συμβατότητας
είναι διαθέσιμο στη διεύθυνση: www.asus.com/support
Magyar Az ASUSTeK Computer Inc. ezennel kijelenti, hogy ez az eszköz
megfelel a kapcsolódó Irányelvek lényeges követelményeinek és egyéb
vonatkozó rendelkezéseinek. Az EU megfelelőségi nyilatkozat teljes szövege
innen letölthető: www.asus.com/support
Latviski ASUSTeK Computer Inc. ar šo paziņo, ka šī ierīce atbilst saistīto
Direktīvu būtiskajām prasībām un citiem citiem saistošajiem nosacījumiem.
Pilns ES atbilstības paziņojuma teksts pieejams šeit: www.asus.com/support
Lietuvių „ASUSTeK Computer Inc.“ šiuo tvirtina, kad šis įrenginys atitinka
pagrindinius reikalavimus ir kitas svarbias susijusių direktyvų nuostatas. Visą
ES atitikties deklaracijos tekstą galima rasti: www.asus.com/support
Norsk ASUSTeK Computer Inc. erklærer herved at denne enheten er i
samsvar med hovedsaklige krav og andre relevante forskrifter i relaterte
direktiver. Fullstendig tekst for EU-samsvarserklæringen finnes på:
www.asus.com/support
Polski Firma ASUSTeK Computer Inc. niniejszym oświadcza, że
urządzenie to jest zgodne z zasadniczymi wymogami i innymi właściwymi
postanowieniami powiązanych dyrektyw. Pełny tekst deklaracji zgodności UE
jest dostępny pod adresem: www.asus.com/support
Português A ASUSTeK Computer Inc. declara que este dispositivo está em
conformidade com os requisitos essenciais e outras disposições relevantes
das Diretivas relacionadas. Texto integral da declaração da UE disponível em:
www.asus.com/support
A-8
Română ASUSTeK Computer Inc. declară că acest dispozitiv se conformează
cerinţelor esenţiale şi altor prevederi relevante ale directivelor conexe. Textul
complet al declaraţiei de conformitate a Uniunii Europene se găseşte la:
www.asus.com/support
Srpski ASUSTeK Computer Inc. ovim izjavljuje da je ovaj uređaj u saglasnosti
sa osnovnim zahtevima i drugim relevantnim odredbama povezanih
Direktiva. Pun tekst EU deklaracije o usaglašenosti je dostupan da adresi:
www.asus.com/support
Slovensky Spoločnosť ASUSTeK Computer Inc. týmto vyhlasuje, že toto
zariadenie vyhovuje základným požiadavkám a ostatým príslušným
ustanoveniam príslušných smerníc. Celý text vyhlásenia o zhode pre štáty EÚ
je dostupný na adrese: www.asus.com/support
Slovenščina ASUSTeK Computer Inc. izjavlja, da je ta naprava skladna z
bistvenimi zahtevami in drugimi ustreznimi določbami povezanih direktiv.
Celotno besedilo EU-izjave o skladnosti je na voljo na spletnem mestu:
www.asus.com/support
Español Por la presente, ASUSTeK Computer Inc. declara que este dispositivo
cumple los requisitos básicos y otras disposiciones pertinentes de las
directivas relacionadas. El texto completo de la declaración de la UE de
conformidad está disponible en: www.asus.com/support
Svenska ASUSTeK Computer Inc. förklarar härmed att denna
enhet överensstämmer med de grundläggande kraven och andra
relevanta föreskrifter i relaterade direktiv. Fulltext av EU-försäkran om
överensstämmelse finns på: www.asus.com/support
Українська ASUSTeK Computer Inc. заявляє, що цей пристрій відповідає
основним вимогам та іншим відповідним положенням відповідних
Директив. Повний текст декларації відповідності стандартам ЄС
доступний на: www.asus.com/support
Türkçe AsusTek Computer Inc., bu aygıtın temel gereksinimlerle ve ilişkili
Yönergelerin diğer ilgili koşullarıyla uyumlu olduğunu beyan eder. AB
uygunluk bildiriminin tam metni şu adreste bulunabilir:
www.asus.com/support
Bosanski ASUSTeK Computer Inc. ovim izjavljuje da je ovaj uređaj usklađen
sa bitnim zahtjevima i ostalim odgovarajućim odredbama vezanih direktiva.
Cijeli tekst EU izjave o usklađenosti dostupan je na: www.asus.com/support
Appendix
ASUS contact information
ASUSTeK COMPUTER INC.
Address
Telephone Fax Web site
Technical Support
Telephone Fax
Online support
4F, No. 150, Li-Te Road, Peitou, Taipei 112, Taiwan
+886-2-2894-3447
+886-2-2890-7798
www.asus.com
+86-21-38429911
+86-21-5866-8722, ext. 9101#
http://qr.asus.com/techserv
ASUS COMPUTER INTERNATIONAL (America)
Address
800 Corporate Way, Fremont, CA 94539, USA
Telephone+1-510-739-3777
Fax
+1-510-608-4555
Web site
http://www.asus.com/us/
Technical Support
Support fax
Telephone Online support
+1-812-284-0883
+1-812-282-2787
http://qr.asus.com/techserv
ASUS COMPUTER GmbH (Germany and Austria)
Address
Fax
Web site
Online contact
Harkort Str. 21-23, 40880 Ratingen, Germany
+49-2102-959931
http://www.asus.com/de
http://eu-rma.asus.com/sales
Technical Support
Telephone+49-2102-5789555
Support Fax
+49-2102-959911
Online support
http://qr.asus.com/techserv
ASUS Q270M-CM-A
A-9
DECLARATION OF CONFORMITY
Per FCC Part 2 Section 2. 1077(a)
Asus Computer International
Responsible Party Name:
800 Corporate Way, Fremont, CA 94539.
Address:
Phone/Fax No:
(510)739-3777/(510)608-4555
hereby declares that the product
Product Name : Motherboard
Model Number : Q270M-CM-A
Conforms to the following specifications:
FCC Part 15, Subpart B, Unintentional Radiators
Supplementary Information:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Representative Person’s Name :
Steve Chang / President
Signature :
Date :
Mar. 1, 2017
Ver. 140331
A-10
Appendix
Download PDF
Similar pages