IHT3807DT
Home Music System with Subwoofer & Dock for iPod
Table of Contents
Warnings and Precautions................................................................................................................2
Important Safety Instructions.............................................................................................................3
Powering the Unit..............................................................................................................................5
Remote Battery Information..............................................................................................................5
Setting the Clock & Setting the Timer................................................................................................6
Tuning the Radio...............................................................................................................................6
Saving Radio Stations to the Memory...............................................................................................7
Docking an iPod & Playing an iPod...................................................................................................7
Location of Controls & Control Definitions................................................................................... 8-15
Parts Information & Service Information..........................................................................................16
Warnings and Precautions
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO
RAIN OR MOISTURE.
This symbol, located on back or bottom of the
unit, is intended to alert the user to the presence
of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
This symbol, located on back or bottom of the
unit, is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
To reduce the risk of electric shock, do not remove cover (or back). There are no user-serviceable parts
inside. Please refer any servicing to qualified service personnel.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
WARNING: Danger of explosion if the remote control’s batteries are incorrectly installed. Replace only
with the same or equivalent battery.
WARNING: Use of this unit near fluorescent lighting may cause interference regarding use of the remote.
If the unit is displaying erratic behavior move away from any fluorescent lighting, as it may be the cause.
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc) batteries.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
2
Important Safety Instructions
1. Read Instructions - All the safety and operating instruction should be read
before the product is operated.
protection against voltage surges and built-up static charges. Article 810 of
the National Electrical Code, ANSI/NFPA 70, provides information with
regard to proper grounding of the mast and supporting structure, grounding
of the mast and supporting structure, grounding of the lead-in wire to an
antenna-discharge unit, size of grounding conductors, location of antennadischarge unit, connection to grounding electrodes, and requirements for
the grounding electrode.
2. Retain Instructions - The safety and operating instruction should be
retained for future reference.
3. Heed Warnings - All warning on the product and in the operating
instructions should be adhered to.
4. Follow instructions - All operating and use instructions should be
followed.
See figure:
5. Cleaning - Unplug this product from the wall outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Clean only with a dry cloth.
6. Attachments - Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
7. Water and Moisture - Do not use this product near water - for example,
near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement,
or near a swimming pool, and the like. The apparatus shall not be exposed
to dripping or splashing and that no objects filled with liquids, such as
vases, shall be placed on apparatus.
8. Accessories - Do not place this product on an unstable cart, stand tripod,
bracket, or table. The product may fall, causing serious injury to a child
or adult, and serious damage to the product. Use only with a cart, stand,
tripod, bracket, or table recommended by the manufacturer, or sold with
the product. Any mounting of the product should follow the manufacturer’s
instructions, and should use a mounting accessory recommended by the
manufacturer.
9. A product and cart combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may cause the appliance and cart
combination to overturn.
See figure:
16. Lightning - For added protection for this product during a lightning storm,
or when it is left unattended and unused for long periods of time, unplug it
from the wall outlet and disconnect the antenna or cable system. This will
prevent damage to the product due to lightning and power-line surges.
17. Power Lines - An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or power circuits,
or where it can fall into such power lines or circuits. When installing
an outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be fatal.
18. Overloading - Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or electric shock.
19. Object and Liquid Entry - Never push objects of any kind into this
product through openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock. Never spill liquid
of any kind on the product.
10. Ventilation - Slots and openings in the cabinet are provided for ventilation
and to ensure reliable operation of the product and to protect it from
overheating, and these openings must not be blocked or covered. The
openings should never be blocked by placing the product on a bed, sofa,
rug, or other similar surface. This product should not be placed in a built-in
installation such as a bookcase or rack unless proper ventilation is provided
or the manufacturer’s instruction have been adhered to.
11. Power Sources - This product should be operated only from the type of
power source indicated on the marking label. If you are not sure of the type
of power supply to your home, consult your product dealer or local power
company. For products intended to operate from battery power, or other
sources, refer to the operating instruction.
12. Grounding or Polarization - This product may be equipped with a
polarized alternating-current line plug (a plug having one blade wider than
the other). This plug will fit into the power outlet only one way. This is a
safety feature. If you are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact your electrician
to replace your obsolete outlet. Do not defeat the safety purpose of the
polarizes plug.
Alternate Warnings - This product is equipped with a three-wire
grounding-type plug, a plug having a third (grounding) pin. This plug
will only fit into a grounding-type power outlet. This is a safety feature.
If you are unable to insert the plug into the outlet, contact your electrician
to replace your obsolete outlet. Do not defeat the safety purpose of the
grounding-type plug.
13. Power-Cord Protection - Power supply cords should be routed so that
they are not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs, convenience
receptacles, and point where they exit from the product.
14. Protective Attachment Plug - The product is equipped with an attachment
plug having overload protection. This is a safety feature. See Instruction
Manual for replacement or resetting of protective device. If replacement of
the plug is required, be sure the service technician has used a replacement
plug specified by the manufacturer that has the same overload protection as
the original plug.
15. Outdoor Antenna Grounding - If an outside antenna is connected to the
receiver, be sure the antenna system is grounded so as to provide some
20. Servicing - Do not attempt to service this product yourself as opening or
removing covers may expose you to dangerous voltage or other hazards.
Refer all servicing to qualified service personnel.
21. Damage Requiring Service - Unplug this product from the wall outlet
and refer servicing to qualified service personnel under the following
conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the operating
instructions as an improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the product to its normal operation.
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance - this
indicates a need for service.
22. Replacement Parts - When replacement parts are required, be sure the
service technician has used replacement parts specified by the manufacturer
or have the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other hazards.
23. Safety Check - Upon completion of any service or repairs to this product,
ask the service technician to perform safety checks to determine that the
product is in proper operating condition.
24. Wall or Ceiling Mounting - The product should be mounted to a wall or
ceiling only as recommended by the manufacturer.
25. Heat - The product should be situated away from heat sources such as
radiators, heat registers, stoves, or other products (including amplifiers)
that produce heat. Battery shall not be exposed to excessive heat such as
sunshine, fire, or the like.
26. Main plug is used as disconnect device and it should remain readily
operable during intended use. In order to disconnect the apparatus from
the mains completely, the mains plug should be disconnected from the
mains socket outlet completely.
27. Excessive sound pressure from earphones and headphones can cause
hearing loss.
3
In the Box
•
•
•
•
•
•
IHT3807DT
Docking Brackets for iPod
Auxiliary Input Cable (R/L RCA to 3.5mm)
AM Loop Antenna
FM Wire Antenna
Remote Control (Batteries Included)
Features
•
•
•
•
•
•
•
•
4
Motorized Dock for iPod
2.1 Channel Speaker System
Digital Tune AM/FM Radio
Digital Clock with Timer and Sleep Functions
Backlit LCD Display
Auxiliary Inputs and Subwoofer Output
Full-Featured Remote Control
AC Power
Powering the Unit
ЇЇ Power the unit by
connecting it to a
standard AC power
outlet (120V/60Hz).
Remote Battery Information
ЇЇ Power the remote
control by inserting
two AAA Batteries
into it’s battery
compartment.
AAA Battery
• Do not mix
alkaline, standard
(carbon-zinc), or
rechargeable (nicad, ni-mh, etc)
batteries.
AAA Battery
• Do not mix old and
new batteries.
5
Setting the Clock
Step 1: With the player off, press the Select Button.
Step 2: When the time begins to blink on the LCD Display, press the right and
left arrows on the Navigational Buttons to adjust the hour and minute.
Step 3: Wait 5 seconds, and the clock will be set with the specified time.
Setting the Timer
Step 1: With the player off, press the Timer Button. Press the Timer Button
again to cycle through the different timer options (TIMER ON, TIMER
OFF, ON, and OFF).
Step 2: At the TIMER ON or TIMER OFF functions (indicated by ON or OFF
followed by a time) press the right arrow on the Navigational Buttons to
cycle up through the hour and press the left arrow to cycle up through the
minute.
Step 3: After the TIMER ON and/or TIMER OFF functions are set, press the
Timer Button until the LCD Display reads ON by itself. (OFF by itself
indicates that the timer is deactivated)
Step 4: Wait for 5 seconds, and the timer functions will be set with the specified
time.
Tuning the Radio
Step 1: Press the Source Button consecutively to select the FM or AM radio
mode.
Step 2: Tune to the desired station using the Navigation Buttons on the unit or
the Tune Buttons on the remote.
6
Saving Radio Stations to the Memory
Step 1: Press the Source Button consecutively to select the FM or AM radio
mode.
Step 2: Tune to the desired station using the Navigation Buttons on the unit or
the Tune Button on the remote.
Step 3: Press the Menu Button on the unit or the Memory Button on the remote
control.
Step 4: Press the Navigation Buttons to select a preset to save the current station
under.
Step 5: After the preset has been selected press the Menu Button. The current
radio frequency is now saved to the selected preset number.
• There are 20 FM and 10 AM memory presets on this unit.
Docking an iPod
Step 1: Locate the numbered bracket that fits the iPod that will be docked.
• Each included bracket has a number on it, indicating which iPod model
that bracket is compatible with. See the separate bracket chart page to
identify which bracket is needed.
Step 2: Snap the bracket into place over the iPod connector in the Dock for iPod.
• All brackets will only fit one way onto the Dock for iPod.
• When inserting an iPod nano (first or second generation), slide the
Dock Connection on the unit so that it matches the opening on the iPod
nano.
Step 3: Connect the iPod to the iPod connector inside the Dock for iPod.
Step 4: Once an iPod is connected to the Dock for iPod, the unit will charge the
iPod.
Playing an iPod
Step 1: Press the Power Button to turn the unit on.
Step 2: Press the iPod Drawer Button to open the motorized Dock for iPod.
Step 3: Press the Source Button to switch the unit to iPod mode.
Step 4: Press the Play/Pause Button to begin playing the docked iPod.
7
Location of Controls
1
6
2
7
Top
3
8
4
9
5
10
Front
11
8
Control Definitions
1 Menu Button
Press the Menu Button to access and move through the menus of a docked iPod.
Press the Menu Button to enter the Memory mode and save radio stations from
Radio mode.
2 Source Button
Press the Source Button to switch between iPod, Radio, and Auxiliary Input mode.
3 Power Button
Press the Power Button to turn the unit off and on.
4 Play/Pause Button
Press the Play/Pause Button to play or pause a docked iPod.
5 EQ Button
Press the EQ button to switch equalizer modes between Classic, Jazz, Rock, Pop,
and Flat.
6 Timer Button
Press the Timer Button to adjust the unit to turn on or off at a specified time.
7 Sleep Button
Press the Sleep Button consecutively to adjust the sleep timer between 5 and 90
minutes.
• After the allotted time has expired, the unit will power off.
Press the Sleep Button on the unit to delay the alarm for an additional 9 minutes
after it has sounded.
8 iPod Drawer Button
Press the iPod Drawer Button to open or close the motorized dock for iPod.
9 Volume Buttons
Press the Volume Buttons to increase or decrease the volume of audio output from
the unit.
10 Navigational/Select Buttons
Use the Navigational Buttons to navigate through a docked iPod’s menus (iPod
Mode), or to change the radio station (Radio Mode). Press the Select Button to
select and play a file from a docked iPod, or to finish setting the clock on the unit.
11 LCD Display
The LCD Display communicates the time, current source, and timer or sleep
settings.
9
Location of Controls
16
17
Back
18
12
Back
13
19
14
15
Right Side
20
11
Control Definitions
12 AM Antenna Input
Use the AM Antenna Input to connect an AM Antenna to the unit.
13 FM Antenna Input
Use the FM Antenna Input to connect an FM Antenna to the unit.
14 Auxiliary Input 1
Use the Auxiliary Input to connect an external audio player to the unit.
• The unit’s Source must be adjusted to Auxiliary Input mode to play audio from
an external player.
15 Subwoofer Output
Use the Subwoofer Output to connect the unit to an external subwoofer.
16 Auxiliary Input 2
Use the Auxiliary Input to connect an external audio player to the unit.
• The unit’s Source must be adjusted to Auxiliary Input mode to play audio from
an external player.
17 Reset Button
Press the Reset Button to restore the unit to it’s original manufacturer’s settings.
• Use a paperclip or like object to press the Reset Button.
18 Fuse ( T1.6L 250V )
If the unit stops working unexpectedly, the internal fuse may have blown. Unplug
the unit, and replace the fuse with an equivalent type to correct the issue.
19 AC Power Cable ( AC~120V/60Hz )
Plug the AC Power Cable into a standard AC power outlet (120V/60Hz) to power
the unit.
20 Headphone Output
Use the Headphone Output to connect a set of headphones or earbuds to the unit.
11
Location of Controls
Remote
21
22
23
24
25
26
27
28
29
30
31
32
11
Control Definitions
21 Power Button
Press the Power Button to turn the unit off and on.
22 Mute Button
Press the Mute Button to reduce the volume of audio output from the unit entirely.
23 Snooze Button
Press the Snooze Button to delay the alarm for an additional 9 minutes after it has
sounded.
24 Timer Button
Press the Timer Button to adjust the unit to turn on or off at a specified time.
25 Sleep Button
Press the Sleep Button consecutively to adjust the sleep timer between 5 and 90
minutes.
• After the allotted time has expired, the unit will power off.
26 Repeat Button
Press the Repeat Button to set a docked iPod to repeat a single song, or an entire
album or playlist.
• The docked iPod’s screen will indicate if the Repeat function has been
activated.
27 Bass Button
Press the Bass Button to adjust the levels of bass output from the unit.
28 Navigational/Select Buttons
Use the Navigational Buttons to navigate through a docked iPod’s menus (iPod
Mode), or to change the radio station (Radio Mode). Press the Select Button to
select and play a file from a docked iPod, or to finish setting the clock on the unit.
29 Shuffle Button
Press the Shuffle Button to set a docked iPod to play tracks in a random order.
• The docked iPod’s screen will indicate if the Shuffle function has been
activated.
30 Menu Button
Press the Menu Button to access and navigate through menus on a docked iPod.
31 Tune Buttons
Press the Tune Buttons to adjust the AM or FM radio frequency in Radio mode.
32 Stop Button
Press the Stop Button to stop a docked iPod during play.
11
Location of Controls
Remote
37
38
39
40
41
42
33
43
34
44
35
45
36
46
11
Control Definitions
33 Chapter Buttons
Press the Chapter Buttons to cycle through chapters on a docked iPod.
34 Album Buttons
Press the Album Buttons to cycle through albums on a docked iPod.
35 Source Button
Press the Source Button to switch between iPod, Radio, and Auxiliary Input mode.
36 Display Button
Press the Display Button to view the time on the LCD Display when in Radio
mode.
37 iPod Drawer Button
Press the iPod Drawer Button to open or close the motorized dock for iPod.
38 EQ Button
Press the EQ button to switch equalizer modes between Classic, Jazz, Rock, Pop,
and Flat.
39 Treble Button
Press the Treble Button to adjust the levels of treble output from the unit.
40 Clock Button
Press the Clock Button, with the unit powered off, to set the time on the unit.
41 Volume Buttons
Press the Volume Buttons to increase or decrease the volume of audio output from
the unit.
42 Play/Pause Button
Press the Play/Pause Button to play or pause a docked iPod.
43 Memory Buttons
Press the Memory Buttons to cycle through radio stations saved to the unit’s
memory when in Radio mode.
44 Playlist Buttons
Press the Playlist Buttons to cycle through playlists on a docked iPod.
45 Aux Button
Press the Aux Button to switch the unit to Auxiliary Input Mode
46 Memory Button
Press the Memory Button in Radio mode to save the current radio station to the
unit’s memory.
• There are 20 FM and 10 AM memory presets on this unit.
11
Parts Information
Address:
Phone:
Fax:
Email: 2116 Carr Street, St. Louis MO, 63106
1-314-621-2881
1-314-588-1805
partsinfo@dpi-global.com
Service Information
Address:
Phone:
Fax:
Email: Website:
Version:
2116 Carr Street, St. Louis MO, 63106
1-314-621-2881
1-314-588-1805
customerservice@iLive.net
www.iLive.net
V- 050608-PT
To download this Instruction Manual in English, Spanish, or French visit the Support
section at www.ilive.net.
Para descargar este manual de instrucción en inglés, español, o francés visite la sección
de la ayuda en www.ilive.net.
Pour télécharger ce manuel d’instruction en anglais, espagnol, ou le Français visitez la
section de soutien à www.ilive.net.
© 2008 Digital Products International (DPI, Inc.)
All other trademarks appearing herein are the property of their respective owners.
Download PDF
Similar pages