Data Sheet
iSC2F
Single Port RS-232/422/485 to Fiber Media Converter
IEC 61850-3 and IEEE 1613 Compliant
Features
•
Provides serial copper to optical conversion
•
Support for 1 x RS232/422/485 serial port to 1 x 10FL
Multimode ST fiber port
•
Supports full/half duplex operation
•
Supports multiple baud rates
•
Dual DC Input 9-36VDC or Dual Input 36-75VDC,
Single Input 110-370VDC or 90-264VAC
•
IP-40 Galvanized Steel Housing
•
DIN-Rail mounting
Tel: +1 905-670-0004
Toll Free : +1 844-520-0588
Technical Support: +1 844-475-8324
Email: info@is5com.com
www. is5com.com
All specifications are subject to change without notice.
DS-iSC2F-3-EN.docx
Page—1
www.iS5com.com
Introduction
The iSC2F is a cost-effective single serial media converter solution for the conversion between
serial RS232/RS485/RS422 interfaces and optical fiber. The iMC2F has been designed for power
substation applications and rolling stock applications and is fully compliant with the IEC 618503 and IEEE 1613 standards.
The iSC2F accepts a wide input voltage range from dual 9-36VDC or 36-75VDC power inputs to a
single input of 110-370VDC or 90-264VAC, which makes it suitable for harsh operating
environment. These features combined with a wide operating temperature of -40°C to 85°C help
protect mission-critical applications from network interruptions or temporary malfunctions.
The iSC2F supports the following functions:
•
Two-wire RS232 compliant (TX, RX)
•
Two-wire RS485 half-duplex compliant (D+, D-)
•
Four-wire RS485/422 full-duplex compliant (TX+, TX-, RX+, RX-)
•
Switch selectable 120  terminations
•
Up to 5 km multimode fiber
•
Selectable Fiber Repeater Mode (fiber in -> fiber out)
•
TX/RX LED indicators on RS232/485/422 traffic
•
Configurable RS485 half-duplex turn-around time
•
1200-115200 baud supported
The ISC2F is equipped to provide conversion from serial (RS232, RS485, or RS422) to fiber optics
or between serial standards (RS232 to RS485 / RS422).
Serial to fiber optical conversion connections can be:
•
•
•
Point-to-Point
Fiber Repeater Mode
Standard Serial Connection
All specifications are subject to change without notice.
DS-iSC2F-3-EN.docx
Page—2
www.iS5com.com
By using the DIP switches, iSC2F can be used in the following operating modes.
Serial-to-Fiber Conversion—Point-to-Point
1. RS232 device
2. iSC2F
3. RS485 Device/ Network
Note that the distance between the two ISC2 devices should be less than 5 km (3.1 mi).
Fiber Repeater Mode
When a distance that is more than 5 km (3.1 mi) has to be supported, iSC2F must be used in Fiber
Repeater mode. This mode supports extended distance between serial devices.
1. RS232 device
2. iSC2F
3. RS485 Device/ Network
All specifications are subject to change without notice.
DS-iSC2F-3-EN.docx
Page—3
www.iS5com.com
Serial Standard Conversion
1. RS232 device
2. iSC2F
3. RS485 Device/ Network
All specifications are subject to change without notice.
DS-iSC2F-3-EN.docx
Page—4
www.iS5com.com
Specifications
Model Number
iSC2F
Physical Ports
10M Fiber port
1
RS232/RS422/RS485
1 (2 for RS232 to RS485 conversion)
Power
Input power
Dual DC Inputs of 9-36VDC or Dual Input 36-75VDC, or single Input 110-370VDC or 90-264VAC
Power consumption (Typ.)
5 Watts
Overload current protection
Present
Reverse polarity protection
Present on terminal block
Physical Characteristics
Enclosure
IP-40 Galvanized Steel
Dimension (W x D x H)
76.2(W) x 92.8(D) x 148.3(H)mm (3.0 x 3.65 x 5.84 inches)
Weight (g)
~1000 g
Environmental
Storage Temperature
-40oC to +85oC (-40o to 185oF)
Operating Temperature
-40oC to +85oC (-40o to 185oF)
Operating Humidity
5% to 95% Non-condensing
Regulatory Approvals
EMI
FCC Part 15, CISPR (EN55022) class A, EN50155 (EN50121-3-2, EN55011, EN50121-4)
EMS
EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge),
EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11
Shock
IEC60068-2-27
Free Fall
IEC60068-2-32
Vibration
IEC60068-2-6
Safety
EN60950-1
Warranty
Warranty
5 Years
All specifications are subject to change without notice.
DS-iSC2F-3-EN.docx
Page—5
www.iS5com.com
Dimensions
All dimensions are shown in inches.
All specifications are subject to change without notice.
DS-iSC2F-3-EN.docx
Page—6
www.iS5com.com
Ordering Information
Base
Power
Supply 1
Mount
Fiber Port 1
Serial Port 1
Conformal
Coating
iSC2F
LV
D
1MMSTFL
1PL07
C1
iSC2F
|
|
|
|
|
Core assembly and packaging
LV
|
|
|
|
Dual Input 9-36VDC
MV
|
|
|
|
Dual Input 36-75VDC
HV
|
|
|
|
Single Input 110-370VDC or 90-264VAC
D
|
|
|
DIN Rail Mounting
1MMSTFL
|
|
1 X 10FL Multimode ST
1PL07
1 X RS232/422/485 (7-pole terminal block)
C1
Example Order
Code
Description:
Description
Conformal Coating
iSC2F-LV-D-1MMSTFL-1PL07-C1
Single Port RS232/422/485 to Fiber Media Converter, (Power Supply 1) Dual Input 9-36VDC, (Mount) DIN
Rail Mounting, (Fiber Port 1) 1 X 10FL Multimode ST, (Serial Port 1) 1 X RS232/422/485 (7-pole terminal
block), C1 - added for conformal coating.
All specifications are subject to change without notice.
DS-iSC2F-3-EN.docx
Page—7
Download PDF
Similar pages