Instruction manual
MTL industrial network solutions
MTL RugiCAM-IP
May 2017
INM MTL RugiCAM-IP rev 4
Intrinsically Safe network camera
and LED lighting unit
DECLARATION OF CONFORMITY
A printed version of the Declaration of Conformity has been provided separately within the original shipment of
goods. However, you can find a copy of the latest version at -
http://www.mtl-inst.com/certificates
ii
INM MTL RugiCAM-IP rev 4
DECLARATION OF CONFORMITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
1
INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2
FEATURES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
3
CONNECTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
4
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
5
CONNECTING THE RUGICAM-IP TO A PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
5.1
Internet Explorer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
5.2
Connecting RugiCAM-IP to a network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
5.2.1
Accessing the video preview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5.3
IE Interface Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6/7
5.4
Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.4.1
Image Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.4.2
Basic Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.4.3
Exposure Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9/10
5.4.4
White Balance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.4.5
Day-Night Mode Shift. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.4.6
Wide Dynamic Range (WDR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.4.7
Noise Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.5
Video Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.5.1
Video Combo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-15
5.5.2
Video Flip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.5.3
Text Overlay. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16/17
5.5.4
Area Mask. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.5.5
Analog Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.5.6
Encoding Parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.6
Video Analytics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.6.1
Face Recognition (Optional):. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19/20
5.6.2
Motion Detection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5.7
Audio Setting (Not Supported) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
5.8
Time Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
5.9
Network Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
5.9.1
LAN Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
5.9.2
WIFI Access. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
5.9.3
WIFI Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
5.9.4
Streaming Media. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
5.10
Alarm Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
5.10.1
Alarm Input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24/25
5.10.2
Alarm Action. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25/26
5.10.3
FTP Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5.10.4
EMail Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5.11
RsPort - (Not used at present) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.11.1
RsPort Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27/28
INM MTL RugiCAM-IP rev 4
iii
5.12
System Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
5.12.1
Device Upgrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
5.12.2
Restart Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
5.12.3
Restore to factory settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
5.12.4
Event Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
5.12.5
SNMP Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
5.12.6
Edit User. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30/31
5.13
Recording Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
5.13.1
Recording Plan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31/32
5.13.2
Alarm Videos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
5.13.3
Alarm snapshot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
5.13.4
SD Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
5.14
About Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
5.14.1
Camera Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
6
MECHANICAL DETAILS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
7
ENVIRONMENTAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
8
WASTE REMOVAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
9
MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
10 CERTIFICATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
10.1 Marking Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
11
ORDERING INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
12
APPENDIX A - Install Active-X add-on to the IE interface . . . . . . . . . . . . . . . . . . . . . . 38/39
13
APPENDIX B - How to use WIFI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
14
APPENDIX C - Streaming video via RTSP on VLC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
15
APPENDIX D - Milestone XProtect Surveillance Software. . . . . . . . . . . . . . . . . . . . . . . . 42
15.1
Download Milestone Protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
15.2
Run Milestone XProtect. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
15.3
Add Hardware Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42-46
15.4
Manage the functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47/48
15.5
Open Milestone XProtect Smart Client. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
16
iv
GLOSSARY OF TERMS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
INM MTL RugiCAM-IP rev 4
MTL RugiCAM-IP Intrinsically Safe
Network camera and LED lighting unit
1
INTRODUCTION
1.1
Description
The RugiCAM-IP is an Intrinsically Safe IP Network Camera capable of producing
high quality colour video images at up to 1920x1080p at 30fps.
The H.264 compression technique ensures optimal bandwidth usage of the
Ethernet network and compatibility with all major video streaming players.
Optional LED lighting units are available to further enhance the cameras low light
capability where needed. These are available as either White LED or Infra-Red (IR)
LED types to suit the application, the IR type also having an ambient light sensor
that can automatically switch the camera to IR night mode (monochrome) whilst also
turning on all connected IR LED units.
The IP66 rated units are constructed from high quality anodised aluminium, powder
coated steel or stainless steel to suit different applications and environments and
contains a fully encapsulated camera (or LED) module. The resulting compact and
cost effective solution is suited to many HD video monitoring and surveillance
applications in and around the Hazardous Area.
The connections are made by multi-pin M12 plug and sockets on the rear of the
unit. This allows easy installation and maintenance in the event of a damaged cable
assembly.
2
FEATURES
• Resolution 1920x1080p, 1280x720, D1
• 1/2.8” SONY CMOS Sensor with Mega-Pixel 4mm f1.6 IR Lens
• H.264 Server with Adjustable Frame Rate - Controls Network
Bandwidth Usage (30fps max)
• Micro-SD Card slot (internal) 32GB max – for local recording on trigger events
• 10/100 IS Ethernet Interface supports up to 100m Cat5e/Cat6 Connection
• Wi-Fi (optional) supporting 802.11 b/g/n standards at up to 150Mbps
• 12VDC IS Power Supply Input or PoExTM (Power over IS Ethernet)
• Plug & Socket Connections - shortens installation time
• Rugged IP66 rated Anodised Aluminium, Powder Coated Steel or Stainless
Steel Enclosure suitable for harsh environments
• Compact dimensions (Camera W:87xH:79xD:165mm / LED
W:87xH:79xD:105mm)
• Operating Temperature: -20ºC to +60ºC
• Intrinsically Safe ‘Ex ia’ Group I Mining M1 and Group IIB ATEX and IECEx
Certified for Gas and Dust.
•
Zone 1/ Zone 21 Mounting (Zone 0 / Zone 20 with a suitable Ex ia
Power Supply)
NOTE
The unit is certified to operate safely at -40°C while the standard designed
operating/storage range is -20°C to +60°C, the unit will function at -40°C. Some
aspects of performance are not guaranteed by design at temperature below -20°C
(e.g. Wi-Fi range), additionally possible issues with condensation or frosting of the
glass window should be considered at low temperatures, both of these depend on
the actual installation and environment and may not affect all applications.
INM MTL RugiCAM-IP rev 4
1
3
CONNECTIONS
CAMERA UNIT CONNECTORS
LED UNIT CONNECTORS
12Vdc Power / RS485
X1 4 Pole M12 Connector (M)
Wire Colour
Description
12Vdc Power
X1 4 Pole M12 Connector (M)
Wire Colour
Description
1
Brown
RS485 - A
1
Brown
-
2
White
RS485 - B
2
White
-
3
Blue
+12Vdc
3
Blue
+12Vdc
4
Black
0V
4
Black
0V
LED Interface
X2 4 Pole M12 Connector (F)
Wire Colour
Description
LED Interface (To Camera)
X2 4 Pole M12 Connector (M)
Wire Colour
Description
1
Brown
LED IN
1
Brown
LED OUT
2
White
LED OUT
2
White
LED IN
3
Blue
-
3
Blue
-
4
Black
0V
4
Black
0V
WiFi Antenna
X4 TNC Connector
Description
LED Interface (To Other LEDs)
X3 4 Pole M12 Connector (F)
Wire Colour
Description
2.4GHz Antenna
-
1
Brown
-
2
White
LED IN
3
Blue
-
4
Black
0V
Ethernet LAN
X5 8 Pole M12 Connector
Wire Colour
Description
RJ45
Connector
1
ORG-WHT
Tx+
1
2
ORG
Tx-
2
3
GRN-WHT
Rx+
3
4
GRN
Rx-
6
5
BRN-WH
PoEx-
7
6
BRN
PoEx-
8
7
BLU-WHT
PoEx+
5
8
BLU
PoEx+
4
shield
screen
GND
shield
NOTE
The cable core colours as shown in the diagrams above are for reference if using an MTL
supplied cable assembly. Alternatively some cables may have black cores numbered 1-4
corresponding to the M12 connector pin #.
2
INM MTL RugiCAM-IP rev 4
Camera Unit
4
LED Unit
INSTALLATION
The RugiCAM-IP is an Intrinsically Safe IP Network Camera capable of producing
high quality colour video images at up to 1920x1080p at 30fps.
The H.264 compression technique ensure optimal bandwidth usage of the Ethernet
network and compatibility with all major video streaming players.
Optional LED lighting units are available to further enhance the cameras low light
capability where needed. These are available as either White LED or Infra-Red (IR)
LED types to suit the application, the IR type also having an ambient light sensor
that can automatically switch the camera to IR night mode (monochrome) whilst also
turning on all connected IR LED units.
The IP66 rated units are constructed from high quality anodised aluminium, powder
coated steel or stainless steel to suit different applications and environments and
contains a fully encapsulated camera (or LED) module. The resulting compact and
cost effective solution is suited to many HD video monitoring and surveillance
applications in and around the Hazardous Area.
The connections are made by multi-pin M12 plug and sockets on the rear of the
unit. This allows easy installation and maintenance in the event of a damaged cable
assembly.
WARNING!
This equipment must be installed, operated and maintained only be trained
competent personnel and in accordance with all appropriate international,
national and local standard codes of practice and site regulation for intrinsically
safe apparatus and in accordance with the instructions contained here.
NOTE
Refer to certificate for ‘Special Conditions of Safe Use’
LED UNIT
• White led (colour temperature 6500k) unit. led angle 170degrees.
• IR led ( wavelength 850nm) unit. led angle 120degrees
• Each led unit requires an is power supply on connector x1
• LEDconnector x2 connects to camera connector x2 (day/night control by led
unit 1 sensor)
• Additional led units can be daisy-chained - led connector x3 connects to x2 on
next led unit
•
INM MTL RugiCAM-IP rev 4
The first LED units integral photo-resistive sensor allows the camera to
automatically switch to night mode (removes IR cut filter and sets
monochrome b/w mode) at low light levels, camera then switches on all
connected LED units. This depends on configuration to be set (section 5.4.5)
using photo-resistive sensor mode.
3
LED Unit
(when used standalone - without camera)
• With just a 12v supply connected LED unit lights up (~300mA). Application
could just switch the supply ON/OFF to control the light.
• If a link is fitted between pin IN to OUT then the light ON/OFF is controlled by
its internal light sensor
• If control pin IN is driven high (2V - 5V) this turns the light OFF, driving low
(0V) or open circuit this pin turns the light ON
5
CONNECTING THE RUGICAM-IP TO A PC
5.1
Internet Explorer
1. Connect IS power to the camera from a suitable IS power supply such as MTL 9492-PS-PLUS.
2. Connect the RugiCAM-IP to a PC with Ethernet cable via an IS isolator, such as MTL 9468-ET and power on the camera.
NOTE
Some older computers need a crossover cable if the NIC doesn’t have
automatic cable switching
3.
On Windows 7, go to Control Panel\Network and Sharing Center; Click
“Local Area Connection” and then click “Properties”. On Windows XP, go
to Control Panel\Network and Internet\Network Connections. Right click on the corresponding Network adapter and then click “Properties”.
4. In Local Area Connection Properties, Click Internet Protocol Version 4
(TCP/ IPv4) Properties.
4
5. Specify IP address and DNS server as in the screenshot below.
6. If necessary, wait for around 45 seconds for the IP Camera to boot up.
INM MTL RugiCAM-IP rev 4
7. Open Internet Explorer, browse for the IP address of the
Camera (http://192.168.0.168/).
8. You should see a login Window where you can enter the username
and Password.
User Name: admin
Password: admin
9. If you run this camera at the first time, you may not be able to see the live
video before you install ActiveX. Please refer to Appendix A to install the
ActiveX control.
NOTE
The default IP address is static IP 192.168.0.168. You can change the static IP
address or set network setting to DHCP in Web Interface.
5.2
Connecting RugiCAM-IP to a network
The IP Camera can also be connected to a network.
To connect the IP Camera to a network via a Router. Make sure the client PC with
correct OS is also connected to the same network.
Connect the external Power to the IP Camera.
The router will assign an IP address to the IP Camera.
The IP Camera will show up on the PC as a UPnP device. UPnP device can be found
in File Explorer>Network (left Pane)>Other Devices.
INM MTL RugiCAM-IP rev 4
5
5.2.1 Accessing the video preview
To access the video preview, please follow the steps below:
1. Type the IP address into Internet Explorer (IE), and you will get asked for a
username and password.
2. In order to complete the installation of the Control successfully through the
browser, the version of IE must be upgraded to 6.0 or above.
6
3. Enter user Name: admin
4. Enter password: admin
5. Click “OK”. You will the get to the video preview as show below
INM MTL RugiCAM-IP rev 4
5.3
IE Interface Overview
The Window displays real-time video images, as shown in the picture above. The
Client interface includes:
• Live video Preview.
• Navigation interface.
As shown on the left side of the webpage above, shown in detail in
the diagram below.
These Interfaces will be introduced in detail in the following sections.
• PTZ interface:
(Not supported at present)
(Future Development)
•Zoom:
Not supported.
•Focus:
Not supported.
•PTZ:
Not supported.
INM MTL RugiCAM-IP rev 4
7
• Recording and Snapshot:
NOTE
When using the Recording function, please run IE as Administrator.
•Recording:
Click the ‘Recording’ icon as shown below to start recording, the video will be saved to your PC; Click the ‘Recording’ icon again, the video recording will stop.
A window will pop up to show the path of the saved video.
NOTE
You may have to search for the file location of the saved video, as it may be
different to that stated, if permission for the location is denied by PC.
•Snapshot:
5.4
Click the ‘Snapshot’ icon as shown below, you will capture an image.
Settings
5.4.1 Image Setting
8
INM MTL RugiCAM-IP rev 4
5.4.2 Basic Adjustment
•Brightness:
Scroll bar to control brightness. (value ranges from 1 to 255)
•Contrast:
Scroll bar to control contrast. (value ranges from 1 to 255)
•Saturation:
Scroll bar to control saturation. (value ranges from 1 to 255)
•Sharpness:
Scroll bar to control sharpness. (value ranges from 1 to 255
5.4.3 Exposure Control
•Auto Exposure:
Click ‘Auto Exposure’ button to enable auto exposure
•Minimum Frame Rate:
Use the pull-down list to choose the minimum frame rate.
•30
•25
•15
•8
•1
INM MTL RugiCAM-IP rev 4
9
•Max Gain:
Use the pull-down list to choose the maximum gain 1 ~ 10.
•Max Digital Gain:
Use the pull-down list to choose the maximum digital gain.
•1024
•2048
•4096
•8191
•Auto Iris:
Click to select auto iris ‘Open’ or ‘Closed’.
•Flicker Control:
Use the pull-down list to choose the anti-flicker frequency.
•60hz flicker
•50hz flicker
• Manual Exposure:
Click ‘Manual Exposure’ button to enable manual exposure
• Exposure Time:
Input manual exposure time as required.
• Gain:
Input exposure gain (1 ~ 10) as required.
10
INM MTL RugiCAM-IP rev 4
5.4.4 White Balance
• White Balance
Click ‘Open’ or ‘Close’ to select or deselect Auto White Balance
5.4.5 Day-Night Mode Shift:
• Day-Night Mode Shift:
Click ‘Manual’ or the ‘Dynamic’ button to enable the required
exposure method
•Manual:
The day/night mode can be set manually.
•Day
•
Night
•Dynamic:
The day/night mode can auto switch depending on the brightness.
• Min Brightness (1- 45):
when the brightness is lower than min, night mode will open.
• Max Brightness (1- 45):
when the brightness is higher than max, day mode will open.
•Depend on photosensitive sensor
Click button to enable the ‘Depend on photosensitive sensor’ setting.
INM MTL RugiCAM-IP rev 4
•
High When Day:
There is a photosensitive chip located on the IR LED board, in low light
conditions a signal will be sent to the CPU and the CPU will set the
camera to night mode.
•
High When Night:
There is a photosensitive chip located on the IR LED board, in nightime
light conditions a signal will be sent to the CPU and the CPU will set
the camera to night mode.
11
5.4.6 Wide Dynamic Range (WDR)
• WDR (Wide dynamic range):
WDR is intended to provide clear images even under backlighting conditions, where the intensity of illumination varies a lot. Click buttons to make
appropriate selection.
•
No WDR
•
Low strength
•
Medium strength
•
High strength
5.4.7 Noise Filter (Not supported)
12
2d and 3D noise filters reduce noise interference.
Click buttons to make appropriate selections
• 2D Filter: Close / Open
• 3D Filter: Close / Open
INM MTL RugiCAM-IP rev 4
5.5
Video Setting
5.5.1 Video Combo
•Main stream
• Resolution:
Use the pull-down list to choose Resolution.
• 1080p: 1920x1080
• 720p: 1280x720
• D1: 704x576
• Framerate:
Use the pull-down list to choose Frame Rate .
•1~30
INM MTL RugiCAM-IP rev 4
13
• Image Quality:
Use the pull-down list to choose Image Quality.
•High
• Medium High
•Medium
• Medium Low
•Low
• Very Low
• Rate Control:
Use the pull-down list to choose Rate Control.
•VBR
•CBR
• Max Bit-rate:
Use the pull-down list to choose Max Bit Rate Control.
•5M
•4M
•3M
•2M
• Sub stream
• Enable Sub stream:
After Enable Sub stream, go to “Live video” and click the
stream name to refresh it, you will get two stream names.
14
INM MTL RugiCAM-IP rev 4
Click “All Bit Streams”, you will get two live videos on the interface.
• Resolution:
• D1: 704x576
• VGA: 640x352
• QVGA: 320x192
• Framerate:
Use the pull-down list to choose Framerate.
•30
•25
•16
•8
•1
• Image Quality:
Use the pull-down list to choose Image Quality.
•High
• Medium High
•Medium
• Medium Low
•Low
• Very Low
• Rate Control:
Use the pull-down list to choose Rate Control.
•VBR
•CBR
• Max Bit-rate:
Use the pull-down list to choose Max Bit Rate.
•2M
•1M
•512kB
INM MTL RugiCAM-IP rev 4
15
5.5.2 Video Flip
Click buttons to make appropriate selection.
•Off
•Horizontal
•Vertical
•Both
5.5.3 Text Overlay
Click check box to make the appropriate selection.
•Main Stream overlay:
•Enable
•Text
•Position:
Use the pull-down list to choose Position.
•
Lower-left corner
•
Lower-right corner
•
Upper-left corner
•
Upper-right corner
•Offset X
Enter the appropriate offset setting.
•Offset Y
Enter the appropriate offset setting.
16
Click check box to make the appropriate selection.
INM MTL RugiCAM-IP rev 4
•Sub Stream overlay:
•Enable
•Text
•Position:
•
Lower-left corner
•
Lower-right corner
•
Upper-left corner
•
Upper-right corner
•Offset X
Enter the appropriate offset setting.
•Offset Y
Enter the appropriate offset setting.
•Time overlay:
Click the Enable check box.
•Date Format:
Use the pull-down list to choose Date Format.
•
YYYY/MM/DD
•
MM/DD/YYYY
•
DD/MM/YYYY
•Time Format:
Use the pull-down list to choose Time Format.
•
12 Hrs
•
24 Hrs
•Position:
Use the pull-down list to choose Position.
•
Lower-left corner
•
Lower-right corner
•
Upper-left corner
•
Upper-right corner
INM MTL RugiCAM-IP rev 4
17
5.5.4 Area Mask
There are two ways to select the area mask. Quick select and Value input select
Up to 4 area masks can be set on the video.
• Quick select:
1 Click “Enable” check box and click “Edit” on the right.
2 Drag mouse on the video to select the area mask.
3 Click “Apply”.
• Value input select:
1 Click “Enable” check box.
2 Input the values of X, Y, Width and Height, then click “Edit”.
3 Click “Apply”.
• Clean area mask:
1 Click “Edit” of the area mask you want to remove.
2 Click “Reset”.
3 Click “Apply”.
5.5.5 Analog Video
Not applicable
5.5.6 Encoding Parameter
Select a Profile, click check box to select and save the selected profile.
•
BaseLine Profile
•
Main Profile
•
High Profile
18
INM MTL RugiCAM-IP rev 4
5.6
Video Analytics
5.6.1 Face Recognition (Optional):
Use the pull-down list to choose Face Recognition options.
•Off
•Detect
• Enhanced Detect
• Region of Interest (ROI):
• X: Enter the x-axis value of the starting pixel for ROI
• Y: Enter the y-axis value of the starting pixel for ROI
• W: Enter the width of the ROI
• H: Enter the height of the ROI
• Confidence Level:
Use the slide bar list to adjust the accuracy of the face detection algorithm.
The value ranges from 1 (lowest) to 100 (highest). The default value is 75.
• Direction:
Use the pull-down list to choose Direction options.
•Up
•Left
•Right
INM MTL RugiCAM-IP rev 4
19
• Privacy Mask:
Use the pull-down list to choose Privacy Mask options.
• Enable Privacy Mask: OFF/ON
• Mask Option: Choose privacy mask pattern.
The default value is Black Box.
5.6.2 Motion Detection
• Click on the video interface or click “Select All” to select
region of interest.
• Click “Clear All” to clear the region of interest.
• Sensitivity:
Use the pull-down list to choose Sensitivity options.
•Low
•Medium
•High
NOTE
See “5.10.1 Alarm Inputs” for information on how to enable motion
detection alarm.
20
INM MTL RugiCAM-IP rev 4
5.7
Audio Setting (Not Supported)
5.8
Time Setting
• Time Zone:
Use the pull-down list to choose required Time Zone.
• Time Setting:
Click buttons to make the appropriate selection.
INM MTL RugiCAM-IP rev 4
• Synchronize with computer time.
• Synchronize with SNTP server.
21
5.9
Network Setting
5.9.1 LAN Setting
• Enable DHCP:
Click buttons to make the appropriate DHCP selection.
•On
•Off
• IP address:
If you disable DHCP, you can set static IP address.
• Netmask
• Gateway
• DNS Server
22
INM MTL RugiCAM-IP rev 4
5.9.2 WIFI Access
• Enable WIFI:
Click buttons to make the appropriate WIFI selection.
•On
•Off
• SSID:
Use the pull-down list to choose your wireless network.
• Password:
Enter the password for your wireless network.
5.9.3 WIFI Setting
• Enable DHCP:
Click buttons to make the appropriate DHCP selection.
•On
•Off
• IP address:
If you disable DHCP, you can set static IP address.
• Netmask
• Gateway
• DNS Server
INM MTL RugiCAM-IP rev 4
23
5.9.4 Streaming Media
• Specify Address : ON/OFF
• Service Address : IP address
5.10 Alarm Setting
5.10.1 Alarm Input
24
INM MTL RugiCAM-IP rev 4
• Enable Alarm: check tick box to Enable Alarm Function
• Motion Detection: Close/Open
• Ethernet Lost Alarm: Close/Open
• Audio Alarm: Close/Open (Not supported)
• External Triggers: Close/Open (Not supported)
• Mask Alarm: Close/Open
5.10.2 Alarm Action
• Voice Play: (Not supported)
OFF/ON
Use the pull-down list to select
• Short Type
• Long Type
• IO Output: (Not supported)
OFF/ON
• 5 s
• 10 s
•always
• UDP report:
OFF/ON
• Alarm Video Recording:
OFF/ON
• Stream Selection:
Use the pull-down list to select
• Main Stream
• Sub Stream
• Video Length:
Use the pull-down list to select
• 5s
•10s
•30s
Storage Location: SD Card/FTP/Shared Folder/ USB Drive
INM MTL RugiCAM-IP rev 4
25
• Alarm snapshot:
OFF/ON
• Quantity of Image:
Use the pull-down list to select
• One
•Two
•Three
5.10.3 Alarm video
5.10.4 Alarm snapshot
26
INM MTL RugiCAM-IP rev 4
5.11
RsPort - (Not used at present)
5.11.1 RsPort Setting
• Enable RS485: select On/Off
•Baud Rate
Use the pull-down list to select options
•
19200
•
9600
•
4800
•
2400
•
1200
•Data Bit
Use the pull-down list to select options
•
8
•
7
•
6
•
5
INM MTL RugiCAM-IP rev 4
27
•Parity Check
Use the pull-down list to select options
•
None
•
Odd
•
Even
•
Space
•Stop Bits
Use the pull-down list to select options
•
1
•
2
•PTZ Protocol
Use the pull-down list to select options
•
Pelco-d
•
Pelco-e
28
•
User-Defined
INM MTL RugiCAM-IP rev 4
5.12 System Maintenance
5.12.1 Device Upgrade
5.12.2 Restart Device
Click “Restart” button to restart camera
5.12.3 Restore to factory settings
Click “Submit” button to reset the camera
5.12.4 Event Log
You can check the system log in this section
INM MTL RugiCAM-IP rev 4
29
5.12.5 SNMP Setting
• Function On/Off: Enable/Disable
• Server IP
•Port
•Interval
5.12.6 Edit User
• Add new user: Click “Add new user”, you will get following window.
• User: Enter the new user name
30
INM MTL RugiCAM-IP rev 4
•Authority
Use the pull-down list to select options
•Admin
•Operator
•Viewer
• Password: Enter the password of new user
•Edit User: Click “Edit” to edit user
•Delete User: Click “Delete” to delete user
5.13 Recording Management
5.13.1 Recording Schedule
INM MTL RugiCAM-IP rev 4
31
• SD Storage:
OFF / ON
Use the pull-down list to select options
•Image
•Video
• Snapshot Plan:
OFF / ON
5.13.2 Alarm Videos
5.13.3 Alarm Snapshot
5.13.4 SD Management
After plugging in the SD card, you can manage or format the SD card in
this interface.
32
INM MTL RugiCAM-IP rev 4
5.14 About Product
5.14.1 Camera Information
•Camera Name
•Product Model
•Hardware Version
•Software Version
•Sensor
INM MTL RugiCAM-IP rev 4
33
6
MECHANICAL DETAILS
All values are approximate.
Camera Unit
Width
Height
Depth
Weight
87mm
79mm
165mm
AA* = 1.5Kg
CS* = 3.5Kg
Width
Height
Depth
Weight
87mm
79mm
105mm
AA* = 1.5Kg
CS* = 3.5Kg
LED Lighting Unit
*Enclosure Material
7
AA = Anodised Aluminium
CS = Coated / Painted Steel
ENVIRONMENTAL
Operating Temperature
-20°C…+60°C
Storage Temperature
-20°C…+60°C
Humidity
0…95% RH, non-condensing
Ingress Protection
IP66
NOTE
The MTL RugiCAM-IP Camera unit and LED Lighting unit are certified for use in an ambient
temperature of -40ºC to +60ºC, the reduced operating range specified in the above table
(Environmental) is guaranteed by design; operation over the full certified range should only be
undertaken after careful consideration and in agreement with the manufacturer.
34
INM MTL RugiCAM-IP rev 4
8
WASTE REMOVAL INFORMATION
The electronic equipment within must not be treated as general
waste. By ensuring that this product is disposed of correctly you will
be helping to prevent potentially negative consequences for the
environment and human health, which could otherwise be caused by
incorrect waste handling of this product.
For more detailed information about take-back and equipment recycling please contact
your local Eaton MTL representative.
9
MAINTENANCE
No routine maintenance is required other than cleaning the glass window.
Any damage that may affect the safe operation of the unit, e.g. – damage to the
enclosure, glass window, connectors or cables should be corrected by replacing the
unit / part / cable with manufacturer approved spares. There are no user serviceable
parts inside and to maintain dust/water seals the unit should not be disassembled by
the end user other than to access the SD card if required.
All screws must be fitted to ensure the integrity of the sealing O-rings.
NOTE
The complete Camera/LED sub-assembly is encapsulated
INM MTL RugiCAM-IP rev 4
35
10
CERTIFICATION
Ex ia I Ma, Category M1
Ex ia IIB T4 Ga
Ex ia IIIC T135°C Da
CML 15ATEX2016X
IECEx CML 15.0008X
See certificates for further information.
10.1 Marking Details
Part No.
9456-ET-xx
IP Camera
Part No.
9459-ET-xx
IP WiFi Camera
Part No.
9457-IR-xx
IR LED Unit
Part No.
9457-WH-xx
White LED Unit
Part No.
9457-GR-xx
Green LED Unit
Part No.
9457-RD-xx
Red LED Unit
xx relates to the enclosure material
AA = Anodised Aluminium
CS = Coated/Painted Steel
36
INM MTL RugiCAM-IP rev 4
11
ORDERING INFORMATION
Camera and LED Units
9456-ET-AA
IP-CAMERA – ALUMINIUM ENCLOSURE
9459-ET-AA
IP-CAMERA (WITH WIFI) – ALUMINIUM ENCLOSURE
9457-IR-AA
IR LED UNIT – ALUMINIUM ENCLOSURE
9457-WH-AA
WHITE LED UNIT – ALUMINIUM ENCLOSURE
9457-GR-AA
GREEN LED UNIT – ALUMINIUM ENCLOSURE*
9457-RD-AA
RED LED UNIT – ALUMINIUM ENCLOSURE*
* Subject to MOQ
9456-ET-CS
IP-CAMERA – STEEL ENCLOSURE
9459-ET-CS
IP-CAMERA (WITH WIFI) – STEEL ENCLOSURE
9457-IR-CS
IR LED UNIT – STEEL ENCLOSURE
9457-WH-CS
WHITE LED UNIT – STEEL ENCLOSURE
9457-GR-CS
GREEN LED UNIT – STEEL ENCLOSURE*
9457-RD-CS
RED LED UNIT – STEEL ENCLOSURE*
* Subject to MOQ
Accessories
9409-ET5
Camera Ethernet Cat6a Cable 5m
(M12 connector 8-pole ⇔ RJ45)
9409-PWR5
Camera/LED Power Cable 5m
(M12 connector 4-pole ⇔ Free end)
9409-LED06
LED-Camera Link Cable 0.6m
(M12 connector 4-pole⇔ M12 connector 4-pole)
Note: The Red and Green LED units are intended for use in other applications – e.g.: Stop/Go Indication for zones and areas etc.
INM MTL RugiCAM-IP rev 4
37
12
APPENDIX A Install Active-X add-on to the IE Interface
Open IE, Go to Internet Options Security Trusted sites.
Click Sites, uncheck Require server verification (https:) for all sites in this zone and add
the IP address of camera to Websites.
For example: http://192.168.0.*
Click Custom level, enable Download unsigned ActiveX controls and Initialize and
script ActiveX controls not marked as safe for scripting.
38
INM MTL RugiCAM-IP rev 4
under Advanced tab, tick the setting “Allow software to run or install even if the
signature is invalid”
On IE interface (after login), reload the page
If you get a message above, click Install.
After installation of the ActiveX control, you will see the live video
INM MTL RugiCAM-IP rev 4
39
13
APPENDIX B How to use WIFI
1. For the first time you use the WIFI function, you need to enter IE interface with
network cable and go to Network Setting > WIFI Access to enable the WIFI. Then
select the WIFI ID and enter password.
Click Save, the camera will reboot.
2. After the camera boots up, you can get the IP address from the serial log screen
(the WIFI IP address is behind the IP address from network cable) or the
UPnP device.
NOTE
Please make sure the camera module and your PC (which access the camera via
WIFI) are in the same network (wifi router)
3. You can also set the static IP of WIFI.
Go to WIFI Settings.
Select Static IP, enter the static IP address and click submit.
The IP camera will reboot in next step. After the camera boots up, the static IP address can be used to open the IE interface.
Select IP Address, enter the IP address, and click save.
The IP camera will reboot . After the camera boots up, the static IP address can be
used to open the IE interface.
40
INM MTL RugiCAM-IP rev 4
14
APPENDIX C Streaming video via RTSP on VLC
Open VLC media player.
Click the Media tab.
Open Network Stream.
In the next window, enter the URL rtsp://<IP_address>:554/0 for main stream or
rtsp://<IP_address>:554/1 for sub stream, then click Play, you will get the video
INM MTL RugiCAM-IP rev 4
41
15
APPENDIX D - MILESTONE XPROTECT SURVEILLANCE SOFTWARE
Milestone XProtect is a surveillance software program. You can try it
free for 30 days and need to purchase a license if you wish to keep
using it.
This guide just briefly illustrates the procedure to run a RugiCAM-IP
camera with Milestone XProtect. If you want more information, please
refer to the user guide of Milestone XProtect, which will come with
the software you download with the link below.
15.1 Download Milestone Protect
Please use the following link to download Milestone XProtect
https://www.milestonesys.com/our-products/xprotect-softwaresuite/xprotect-enterprise/
There are different versions in the download list, and we use the
Milestone XProtect Enterprise in this user guide.
Install Milestone XProtect
15.2 Run Milestone XProtect
After installation, you will get two icons on your desktop
(Milestone XProtect Management Application and Milestone
XProtect Smart Client).
Run Management Application
Open Milestone XProtect Management Application.
15.3 Add Hardware Device
When you get the interface, click Add Hardware Device.
NOTE
Before this step, the IP camera must be running.
Then you will get the following window:
42
INM MTL RugiCAM-IP rev 4
Select and click Scan for Hardware.
NOTE
Please refer to the user guide of Milestone XProtect if you want to use
other ways to add hardware device.
Select Scan local network and click next.
INM MTL RugiCAM-IP rev 4
43
Select all manufacturers (default), then click Next.
NOTE
If the auto-scan cannot get the device, please click Rescan to scan it
again, or you can also use other ways in last window to get the device.
Select LI-M38 Camera and deselect the USB Driver and click next.
44
INM MTL RugiCAM-IP rev 4
The following screen appears:
click OK.
The following screen appears:
From the left panel click on Hardware Device 1 and then select
camera 1. The folowing screen appears:
INM MTL RugiCAM-IP rev 4
45
Select Open to select Camera properties and the following screen appears:
46
INM MTL RugiCAM-IP rev 4
15.4 Manage the functions
Motion Detction can be selected as shown below:
Sensitivity and Motion can be used to adjust the level.
INM MTL RugiCAM-IP rev 4
When the green bar is over the line, the video from the camera
will be recorded.
47
You can also check Show grid to set the detection regions.
Set Privacy Masking
48
The blocks you select will be a black area in video you get from camera. After you set the properties, click OK to save it.
INM MTL RugiCAM-IP rev 4
15.5 Open Milestone XProtect Smart Client
This allows you to view all cameras and view recorded video.
NOTE
If you want to know more about the functions and settings, please refer to
the user guide of Milestone XProtect.
INM MTL RugiCAM-IP rev 4
49
16 GLOSSARY OF TERMS
• Alert: An alert can be in the form of an e-mail or an ftp upload of an
image, that occurs when a sensor is triggered, or motion is detected.
• AVI: Audio Video Interleaved. A Windows multimedia video format
from Microsoft.
• CIF: Common Interface Format. A standard video resolution format used in video conferencing. CIF resolution is 352x288 and bit rate is
36.5 Mbps (at 30fps).
• DHCP: Dynamic Host Configuration Protocol. A system by which each piece of equipment on a network is allocated an address
IP dynamically.
• Ethernet: The most widely used local area network (LAN) access method, defined by the IEEE as the 802.3 standard.
• FTP: File Transfer Protocol. A standard protocol designed for transferring files over a TCP/IP net-work.
•
IP: Internet Protocol. The network layer protocol in the TCP/IP communications protocol suite (the “IP” in TCP/IP). IP contains a network address and allows messages to be routed to a different network or subnet.
• LED: Light Emitting Diode. A semiconductor device that emits light when a voltage is applied.
• Motion detection: Camera function that causes an alert to be triggered when movement is detected in the field of view.
• Protocol: Standards governing the transmission and reception
of data.
• Resolution: Screen resolution is expressed as a matrix of dots. For
example, the VGA resolution of 640x480 means 640 dots (pixels)
across each of the 480 lines.
• RJ-45: Registered Jack 45. RJ-45 type connections are used in
Ethernet devices.
• SNTP: Simple Network Time Protocol. A protocol that allows devices
to update internal clocks using a standard source available on
a network.
• Static IP address: A static IP address that is assigned manually and
never changes.
• TCP/IP: Transmission Control Protocol/Internet Protocol.
A communications protocol developed under contract from the U.S.
•VGA: Video Graphic Array. The video display standard for the PC.
50
INM MTL RugiCAM-IP rev 4
THIS PAGE IS LEFT INTENTIONALLY BLANK
INM MTL RugiCAM-IP rev 4
51
NORWAY
Norex AS
Fekjan 7c, Postboks 147,
N-1378 Nesbru, Norway
AUSTRALIA
MTL Instruments Pty Ltd,
10 Kent Road, Mascot, New South Wales, 2020, Australia
Tel: +61 1300 308 374 Fax: +61 1300 308 463
E-mail: mtlsalesanz@eaton.com
Tel: +47 66 77 43 80 Fax: +47 66 84 55 33
E-mail: info@norex.no
BeNeLux
MTL Instruments BV
Ambacht 6, 5301 KW Zaltbommel
The Netherlands
RUSSIA
Cooper Industries Russia LLC
Elektrozavodskaya Str 33
Building 4
Moscow 107076, Russia
Tel: +31 (0) 418 570290 Fax: +31 (0) 418 541044
E-mail: mtl.benelux@eaton.com
Tel: +7 (495) 981 3770 Fax: +7 (495) 981 3771
E-mail: mtlrussia@eaton.com
CHINA
Cooper Electric (Shanghai) Co. Ltd
955 Shengli Road, Heqing Industrial Park
Pudong New Area, Shanghai 201201
SINGAPORE
Cooper Crouse-Hinds Pte Ltd
No 2 Serangoon North Avenue 5, #06-01 Fu Yu Building
Singapore 554911
Tel: +86 21 2899 3817 Fax: +86 21 2899 3992
E-mail: mtl-cn@eaton.com
Tel: +65 6645 9864 / 9865 Fax: +65 6 645 9865
E-mail: sales.mtlsing@eaton.com
FRANCE
MTL Instruments sarl,
7 rue des Rosiéristes, 69410 Champagne au Mont d’Or
France
SOUTH KOREA
Cooper Crouse-Hinds Korea
7F. Parkland Building 237-11 Nonhyun-dong Gangnam-gu,
Seoul 135-546, South Korea.
Tel: +33 (0)4 37 46 16 53 Fax: +33 (0)4 37 46 17 20
E-mail: mtlfrance@eaton.com
Tel: +82 6380 4805 Fax: +82 6380 4839
E-mail: mtl-korea@eaton.com
GERMANY
MTL Instruments GmbH,
Heinrich-Hertz-Str. 12, 50170 Kerpen, Germany
UNITED ARAB EMIRATES
Cooper Industries/Eaton Corporation
Office 205/206, 2nd Floor SJ Towers, off. Old Airport Road,
Abu Dhabi, United Arab Emirates
Tel: +49 (0)22 73 98 12 - 0 Fax: +49 (0)22 73 98 12 - 2 00
E-mail: csckerpen@eaton.com
INDIA
MTL India,
No.36, Nehru Street, Off Old Mahabalipuram Road
Sholinganallur, Chennai - 600 119, India
Tel: +971 2 44 66 840 Fax: +971 2 44 66 841
E-mail: mtlgulf@eaton.com
Tel: +91 (0) 44 24501660 /24501857 Fax: +91 (0) 44 24501463
E-mail: mtlindiasales@eaton.com
ITALY
MTL Italia srl,
Via San Bovio, 3, 20090 Segrate, Milano, Italy
Tel: +39 02 959501 Fax: +39 02 95950759
E-mail: chmninfo@eaton.com
JAPAN
Cooper Crouse-Hinds Japan KK,
MT Building 3F, 2-7-5 Shiba Daimon, Minato-ku,
Tokyo, Japan 105-0012
UNITED KINGDOM
Eaton Electric Limited,
Great Marlings, Butterfield, Luton
Beds LU2 8DL
Tel: +44 (0)1582 723633 Fax: +44 (0)1582 422283
E-mail: mtlenquiry@eaton.com
AMERICAS
Cooper Crouse-Hinds MTL Inc.
3413 N. Sam Houston Parkway W.
Suite 200, Houston TX 77086, USA
Tel: +1 281-571-8065 Fax: +1 281-571-8069
E-mail: mtl-us-info@eaton.com
Tel: +81 (0)3 6430 3128 Fax: +81 (0)3 6430 3129
E-mail: mtl-jp@eaton.com
Eaton Electric Limited,
Great Marlings, Butterfield, Luton
Beds, LU2 8DL, UK.
Tel: + 44 (0)1582 723633 Fax: + 44 (0)1582 422283
E-mail: mtlenquiry@eaton.com
www.mtl-inst.com
© 2017 Eaton
All Rights Reserved
Publication No. INM MTL RugiCAM-IP rev 4 020517
May 2017
EUROPE (EMEA):
+44 (0)1582 723633
mtlenquiry@eaton.com
THE AMERICAS:
+1 800 835 7075
mtl-us-info@eaton.com
ASIA-PACIFIC:
+65 6645 9864 / 9865
sales.mtlsing@eaton.com
The given data is only intended as a product
description and should not be regarded as a legal
warranty of properties or guarantee. In the interest
of further technical developments, we reserve the
right to make design changes.
Download PDF
Similar pages