huperVision 4000 Vento2 DSS Server Board
Quick Guide
Vento2 516Q / 532Q
Quick Guide
Version 1.0
Published November 2011
Copyright©2011 NEXCOM International Co., Ltd. All rights reserved.
Copyright©2011 Huper Laboratories CO., LTD. All rights reserved.
-1-
huperVision 4000 Vento2 DSS Server Board
Quick Guide
Copyright Notice:
No part of this manual may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means without the written
consent of huperLab and NEXCOM except duplication of documentation by
the purchaser for backup purpose.
Products and corporate names appearing in this manual may or may not be
registered trademarks or copyrights of their respective companies, and are
used only for identification or explanation and to the owners’ benefit without
intent to infringe.
Disclaimer:
Specifications and information contained in this manual are provided for
informational use only. It is subject to change without notice and should not be
recognized as a commitment by huperLab. huperLab assume no responsibility
for any errors or omissions that may appear in this manual. With respect to the
contents of this manual, huperLab and NEXCOM do not provide any kind of
warranty, either expressed or implied.
In no event should huperLab, its directors, officers, employees, or agents be
liable for any indirect, special, incidental, or consequential damages (including
damages for loss of profits, loss of business, loss of data, interruption of
business and the like).
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
-2-
huperVision 4000 Vento2 DSS Server Board
Quick Guide
CALIFORNIA, USA ONLY
The Lithium battery adopted on this motherboard contains Perchlorate, a toxic
substance controlled in Perchlorate Best Management Practices (BMP)
regulations passed by the California Legislature. When you discard the
Lithium battery in California, USA, please follow the related regulations in
advance. “Perchlorate Material-special handling may apply, see
www.dtsc.ca.gov/hazardouswaste/perchlorate”
For more product details, please visit huperLab’s website at
www. huperlab.com
-3-
huperVision 4000 Vento2 DSS Server Board
Quick Guide
huperVision 4000 Vento2 516Q/532Q
Quick Guide
Published on November 2011
Table of Contents
Copyright Notice ........................................................................................... 1 Chapter 1 Introduction ................................................................................. 5
1.1 Package Contents ..................................................................................... 5 1.2 Hardware Specifications ........................................................................... 6 1.3 I/O Panel ................................................................................................... 9
Chapter 2 Installation ................................................................................. 11
2.1 Installing the CPU ................................................................................... 11 2.2 Installing the Fan and Heat Sink ............................................................. 13 2.3 Jumpers and Connectors ........................................................................ 15 Locations of the Jumpers and Connectors .................................................... 17 Chapter 3 BIOS SETUP ............................................................................... 29 3.1 About BIOS Setup ................................................................................... 29 3.2 When to Configure the BIOS................................................................... 29 3.3 BIOS Setup Utility ................................................................................... 30
3.4 Main ........................................................................................................ 30
3.5 Advanced ................................................................................................ 31
3.6 Chipset .................................................................................................... 43
3.7 Boot ........................................................................................................ 47
3.8 Security ................................................................................................... 49
3.9 Save & Exit ............................................................................................. 50
Chapter 4 huperVision Software Installation .......................................... 51
4.1 Easy Steps to Install Software ................................................................ 51 4.2 Simple Steps to Start Recording ............................................................. 55 4.3 Simple Steps to Playback Recordings .................................................... 59 -4-
huperVision 4000 Vento2 DSS Server Board
Quick Guide
Chapter 1 Introduction
Thank you for purchasing huperLab Vento2 516Q / Vento2 532Q DSS Server
Board, a reliable surveillance motherboard produced under huperLab’s
consistently stringent quality control. It delivers excellent performance with
robust design conforming to huperLab’s commitment to quality and endurance.
In this manual, chapter 1 and 2 contain introduction of the motherboard and
introduction of the motherboard and step-by-step guide to the hardware
installation. Chapter 3 and 4 contain the configuration guide to BIOS setup and
information of the Support CD.
1.1 Package Contents
z
huperLab Vento2 516Q / Vento2 532Q Motherboard
(Micro-ATX Form Factor: 9.6-in x 9.6-in, 24.4 cm x 24.4 cm)
z
z
z
huperLab Vento2 516Q / Vento2 532Q Quick Installation Guide
huperLab Vento2 516Q / Vento2 532Q Support CD
huperVision 4000 Software CD
Motherboard Accessories
Vento 516Q: One 16CH Video in Cable
Vento 532Q: Two 16CH Video in Cable & One DB25 Bracket
Audio in cable with bracket (Optional)
TV-Out cable with bracket (Optional)
Audio in / TV-Out cable with bracket (Optional)
One I/O Panel shield
Two Serial ATA (SATA) Data Cable (Optional)
-5-
huperVision 4000 Vento2 DSS Server Board
Quick Guide
1.2 Hardware Specifications
CPU
®
™
™
•Intel Socket 1155 for 2nd Generation Core i7 / Core i5 /
Core™ i3 Processors, Pentium® processor, and Celeron® processor
Chipset
• Intel® Q67 Platform Controller Hub
Main Memory
• 4x 240-pin DDR3 DIMM sockets
• Supports up to 16GB 1066/1333 dual channel DIMM
• Supports non-ECC unbuffered DIMM
Onboard LAN
• 1x Intel® 82579LM PHY for Intel AMT 7.0
• 1x Intel® 82583 PCI Express Gigabit Ethernet
• Supports boot from LAN (PXE)
• 2x RJ45 with LED
Display
• Integrated HD graphics
• 1x VGA
• 1x DVI-D
• 1x HDMI
Note: Vento2 DSS Server Board allows dual display interface
Expansion
• 1x PCIe x16 slot
• 1x Mini PCIe slot
-6-
huperVision 4000 Vento2 DSS Server Board
Quick Guide
Edge I/O Interfaces
• 1x VGA port
• 1x DVI-D port
• 1x HDMI port
• 2x LAN ports
• 4x USB 2.0 ports
• 1x DB25 (Audio/Video input connector)
• 1x Line-in, 1x Line-out(Speaker-out), 1x Mic-in
I/O Interfaces
• 2x SATA III connectors
• 4x SATA II connectors
• 6x USB 2.0 connectors
• 2x RS232/422/485 COM connectors
• 2x 8-pin GPIO connectors
• 2x 20-pin Audio input connector (supports 16CH audio-in)
• 2x 34-pin Video-in connector
• CPU and Chassis fan connectors
• 24-pin ATX power connector
BIOS
• AMI BIOS
• Plug and play support
System Monitor
• 4 Voltages (+3.3V, +5V, +12V, Vcore)
• 3 Temperatures
• 3 FAN speed monitors (1 for CPU and 2 for System FAN)
Power Input
• Supports ATX power supply
• Standard ATX 24-pin connector for +12V/ +5V/ +3.3V/ +5Vsb/ -12V
Dimensions
• microATX
• 244mm (L) x 244mm (W)
-7-
huperVision 4000 Vento2 DSS Server Board
Quick Guide
Environment
• Board level operating temperatures: 0°C to 60°C
• Storage temperature: -20°C to 70°C
• Relative humidity: 10% to 90%, (Non-condensing)
Certifications
• CE approval
• FCC Class A
-8-
huperVision 4000 Vento2 DSS Server Board
Quick Guide
1.3 I/O Panel
1. Line In (Light Blue)
2. Line Out (Green)
3. Microphone (Pink)
7.
8.
9.
USB 2.0 Ports (USB 2/3)
HDMI
Audio/Video Input Port
4. LAN RJ-45 Port (LAN 1)
5. USB 2.0 Ports (USB 0/1)
6. LAN RJ-45 Port (LAN 2)
10. VGA/D-Sub Port
11. DVI-D Port
* There are two LED next to the LAN port. Please refer to the table below for
the LAN port LED indications.
LAN Port LED Indications
Activity / Link LED
Status
Description
Off
No Link
Blinking
Data Activity
SPEED LED
Status
Description
Off
10Mbps connection
Orange
100Mbps connection
Green
1Gbps connection
* To enable Multi-Streaming function, you need to connect a front panel audio
cable to the front panel audio header. Please refer to below steps for the
software setting of Multi-Streaming.
For Windows® XP:
After restarting your computer, you will find “Mixer” tool on your system.
Please select “Mixer ToolBox”
, click “Enable playback multi-streaming”,
and click “ok”. Choose “2CH” or“4CH” and then you are allowed to select
“Realtek HDA Primary output” to use Rear Speaker and Front Speaker, or
-9-
huperVision 4000 Vento2 DSS Server Board
Quick Guide
select “Realtek HDA Audio 2nd output” to use front panel audio. Then
reboot your system.
For Windows® 7 / VistaTM:
After restarting your computer, please double-click “Realtek HD Audio
Manager” on the system tray. Set “Speaker Configuration” to “Quadraphonic”
or “Stereo”. Click “Device advanced settings”, choose “Make front and rear
output devices playbacks two different audio streams simultaneously”, and
click “ok”. Then reboot your system.
- 10 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
Chapter 2 Installation
2.1 Installing the CPU
Before you proceed, make sure (1) the CPU socket comes with a
protective cap, (2) the cap is not damaged and (3) the socket’s
contact pins are not bent.
•
• Make sure all power cables are unplugged before you install the
CPU.
• The CPU socket must not come in contact with anything other
than the CPU. Avoid unnecessary exposure. Remove the protective
cap only when you are about to install the CPU.
1. Unlock the socket by pushing the load lever down (1), moving it
side-ways (2) until it is released from the retention tab; then lift the load
lever up.
2. Lifting the load lever will at the same time lift the load plate. Lift the load
lever up to the angle shown on the photo.
- 11 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
3. Remove the protective cap
from the CPU socket. The cap
is used to protect the CPU
socket against dust and harmful
particles. Remove the protective
cap only when you are about to
install the CPU.
4. Insert the CPU into the socket. The gold triangular mark on the CPU must
align with the corner of the CPU socket shown on the photo.
• Handle the CPU by its edges and avoid touching the pins.
• The CPU will fit in only one orientation and can easily be
inserted without exerting any force.
- 12 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
5.
Close the load plate and then push the load lever down.
While closing the load plate, make sure the front edge of the load plate slides
under the retention knob.
Do not force the CPU into the socket. Forcing the CPU into the socket
may bend the pins and damage the CPU.
6. Hook the load lever under the retention tab.
2.2 Installing the Fan and Heat Sink
T
The CPU must be kept cool by using a CPU fan with heat
sink. Without sufficient air circulation across the CPU and
heat sink, the CPU will over-heat damaging both the CPU and
system board.
1. Before you install the fan / heat sink, you must apply a thermal paste onto the
top of the CPU. The thermal paste is usually supplied when you purchase the
fan / heat sink assembly. Do not spread the paste all over the surface. When
- 13 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
you later place the heat sink on top of the CPU, the compound will disperse
evenly.
Some heat sinks come with a patch of pre-applied thermal paste. Do not apply
thermal paste if the fan / heat sink already has a patch of thermal paste on its
underside. Peel the strip that covers the paste before you place the fan / heat
sink on top of the CPU.
2. Place the heat sink on top of the CPU. The 4 pushpins around the heat sink,
which are used to secure the heat sink onto the system board, must match the
4 mounting holes around the socket.
3. Orient the heat sink such that the CPU fan’s cable is nearest the CPU fan
connector.
4. Rotate each push-pin according to the direction of the arrow shown on top of
the pin.
Push down two pushpins that are diagonally across the heat sink. Perform the
same procedure for the other two push-pins.
5. Connect the CPU fan’s cable to the CPU fan connector on the system board.
- 14 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
2.3 Jumpers and Connectors
Before you Begin
z Ensure you have a stable, clean working environment. Dust and dirt can get
into components and cause a malfunction. Use containers to keep small
components separated.
z Adequate lighting and proper tools can prevent you from accidentally
damaging the internal components. Most of the procedures that follow require
only a few simple tools, including the following:
• A Philips screwdriver
• A flat-tipped screwdriver
• A set of jewelers Screwdrivers
• A grounding strap
• An anti-static pad
• Using your fingers can disconnect most of the connections. It is recommended
that you do not use needle-nosed pliers to disconnect connections as these can
damage the soft metal or plastic parts of the connectors.
• Before working on internal components, make sure that the power is off. Ground
yourself before touching any internal components, by touching a metal object.
Static electricity can damage many of the eletronic components. Humid
environment tend to have less static electricity than dry environments. A
grounding strap is warranted whenever danger of static electricity exists.
Precautions
Computer components and electronic circuit boards can be damaged by
discharges of static electricity. Working on the computers that are still connected
to a power supply can be extremely dangerous. Follow the guidelines below to
avoid damage to your computer or yourself:
• Always disconnect the unit from the power outlet whenever you are working
inside the case.
• If possible, wear a grounded wrist strap when you are working inside the
computer case. lternatively, discharge any static electricity by touching the bare
metal chassis of the unit case, or the bare metal body of any other grounded
appliance.
- 15 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
• Hold electronic circuit boards by the edges only. Do not touch the components
on the board unless it is necessary to do so. Don’t flex or stress the circuit board.
• Leave all components inside the static-proof packaging that they shipped with
until they are ready for installation
• Use correct screws and do not over tighten screws.
Jumper Settings
A jumper is the simplest kind of electric switch. It consists of two metal pins and a
cap. When setting the jumpers, ensure that the jumper caps are placed on the
correct pins. When the jumper cap is placed on both pins, the jumper is short. If
you remove the jumper cap, or place the jumper cap on just one pin, the jumper
is open.
Refer to the illustrations below for examples of what the 2-pin and 3-pin jumpers
look like when they are short (on) and open (off).
Two-Pin Jumpers: Open (Left) and Short (Right)
Three-Pin Jumpers: Pins 1 and 2 Are Short
- 16 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
Locations of the Jumpers and Connectors
Jumpers
CMOS Clear Select
Connector type: 1x3 3-pin header
Connector location: JP7
- 17 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
ME Clear Select
Connector type: 1x3 3-pin header
Connector location: JP8
Watchdog Enable
Connector type: 1x3 3-pin header
Connector location: JP15
Power Mode Select
Connector type: 1x3 3-pin header
Connector location: JP18
- 18 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
Internal Connectors
SATA DOM Power Connector
Connector type: 1x2 2-pin boxed header
Connector location: J1
USB Connectors
Connector type: 2x5 10-pin header
Connector location: JP6 (USB6, USB7), JP3 (USB8, USB9), JP9 (USB4, USB5)
- 19 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
FP Control Connector
Connector type: 2x5 10-pin header
Connector location: JP11
External PS/2 Keyboard/Mouse Connector
Connector size: 1x6 6-pin header
Connector location: J2
- 20 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
System Fan Connectors
Connector type: 1x3, 3-pin Wafer
Connector location: J3, J4
CPU Fan Connector
Connector type: 1x4, 4-pin Wafer
Connector location: FAN1
- 21 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
ATX Power Connector
Connector type: 2x12 24-pin connector
Connector location:
COM1 and COM2 Connectors
Connector type: 2x5, 10-pin header, 2.0mm -M-180
Connector location: CN11 (COM1) and CN12 (COM2)
- 22 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
TV-Out Connectors
Connector type: 2x3, 6-pin header
Connector location: JP1 (TV-Out 7,8) , JP2 (TV-Out 5,6) ,
JP4 (TV-Out 3,4) , JP5 (TV-Out 1,2)
JP5
Pin
Definition
Pin
Definition
1
TV OUT 1
2
GND
3
TV OUT 2
4
GND
5
N/A
6
GND
Pin
Definition
Pin
Definition
1
TV OUT 3
2
GND
3
TV OUT 4
4
GND
5
N/A
6
GND
Pin
Definition
Pin
Definition
1
TV OUT 5
2
GND
3
TV OUT 6
4
GND
5
N/A
6
GND
Pin
Definition
Pin
Definition
1
TV OUT 7
2
GND
3
TV OUT 8
4
GND
5
N/A
6
GND
JP4
JP2
JP1
- 23 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
GPIO Connector 1
Connector type: 2x8, 16-pin header
Connector location: CN5
Pin
Definition
Pin
Definition
1
GPIO 1
2
GND
3
GPIO 2
4
GND
5
GPIO 3
6
GND
7
GPIO 4
8
GND
9
GPIO 5
10
GND
11
GPIO 6
12
GND
13
GPIO 7
14
GND
15
GPIO 8
16
GND
GPIO Connector 2
Connector type: 2x8, 16-pin header
Connector location: CN4
Pin
Definition
Pin
Definition
1
GPIO 9
2
GND
3
GPIO 10
4
GND
5
GPIO 11
6
GND
7
GPIO 12
8
GND
9
GPIO 13
10
GND
11
GPIO 14
12
GND
13
GPIO 15
14
GND
15
GPIO 16
16
GND
- 24 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
GPIO Connector 3
Connector type: 2x6 12-pin header
Connector location: JP12
Pin
Definition
Pin
Definition
1
GP11
2
GP12
3
GP13
4
GP14
5
GPO 1
6
GPO 2
7
GPO 3
8
GPO 4
9
+ 3.3V
10
+ 3.3V
11
GND
12
GND
Camera Audio-in Connector (Rows A and B)
Connector type: 2x10 20-pin header
Connector location: JP17
Pin
Definition
Pin
Definition
1
AUDIO IN 1
2
AUDIO IN 9
3
AUDIO IN 2
4
AUDIO IN 10
5
AUDIO IN 3
6
AUDIO IN 11
7
AUDIO IN 4
8
AUDIO IN 12
9
AUDIO IN 5
10
AUDIO IN 13
11
AUDIO IN 6
12
AUDIO IN 14
13
AUDIO IN 7
14
AUDIO IN 15
15
AUDIO IN 8
16
AUDIO IN 16
17
GND
18
GND
19
N/A
20
GND
- 25 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
Camera Audio-in Connector (Rows C and D)
Connector type: 2x10 20-pin header
Connector location: JP10
Pin
Definition
Pin
Definition
1
AUDIO IN 17
2
AUDIO IN 25
3
AUDIO IN 18
4
AUDIO IN 26
5
AUDIO IN 19
6
AUDIO IN 27
7
AUDIO IN 20
8
AUDIO IN 28
9
AUDIO IN 21
10
AUDIO IN 29
11
AUDIO IN 22
12
AUDIO IN 30
13
AUDIO IN 23
14
AUDIO IN 31
15
AUDIO IN 24
16
AUDIO IN 32
17
GND
18
GND
19
N/A
20
GND
- 26 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
Camera Video-in Connector
Connector type: 2x17 34-pin header
Connector location: CN13
Pin
Definition
Pin
Definition
1
VIDEO IN 1
2
GND
3
VIDEO IN 2
4
GND
5
VIDEO IN 3
6
GND
7
VIDEO IN 4
8
GND
9
VIDEO IN 5
10
GND
11
VIDEO IN 6
12
GND
13
VIDEO IN 7
14
GND
15
VIDEO IN 8
16
GND
17
VIDEO IN 9
18
GND
19
VIDEO IN 10
20
GND
21
VIDEO IN 11
22
GND
23
VIDEO IN 12
24
GND
25
VIDEO IN 13
26
GND
27
VIDEO IN 14
28
GND
29
VIDEO IN 15
30
GND
31
VIDEO IN 16
32
GND
33
GND
34
GND
- 27 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
Camera Video-in Connector
Connector type: 2x17 34-pin header
Connector location: CN9
Pin
Definition
Pin
Definition
1
VIDEO IN 17
2
GND
3
VIDEO IN 18
4
GND
5
VIDEO IN 19
6
GND
7
VIDEO IN 20
8
GND
9
VIDEO IN 21
10
GND
11
VIDEO IN 22
12
GND
13
VIDEO IN 23
14
GND
15
VIDEO IN 24
16
GND
17
VIDEO IN 25
18
GND
19
VIDEO IN 26
20
GND
21
VIDEO IN 27
22
GND
23
VIDEO IN 28
24
GND
25
VIDEO IN 29
26
GND
27
VIDEO IN 30
28
GND
29
VIDEO IN 31
30
GND
31
VIDEO IN 32
32
GND
33
GND
34
GND
- 28 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
Chapter 3 BIOS SETUP
This chapter describes how to use the BIOS setup program for the NEX 881. The
BIOS screens provided in this chapter are for reference only and may change if the
BIOS is updated in the future.
3.1 About BIOS Setup
The BIOS (Basic Input and Output System) Setup program is a menu driven utility
that enables you to make changes to the system configuration and tailor your
system to suit your individual work needs. It is a ROM-based configuration utility
that displays the system’s configuration status and provides you with a tool to set
system parameters.
These parameters are stored in non-volatile battery-backed-up CMOS RAM that
saves this information even when the power is turned off. When the system is
turned back on, the system is configured with the values found in CMOS.
„
Hard drives, diskette drives, and peripherals
„
Video display type and display options
„
Password protection from unauthorized use
„
Power management features
3.2 When to Configure the BIOS
This program should be executed under the following conditions:
„
When changing the system configuration
„
When a configuration error is detected by the system and you are prompted
to make changes to the Setup program
„
When resetting the system clock
„
When redefining the communication ports to prevent any conflicts
„
When making changes to the Power Management configuration
„
When changing the password or making other changes to the security setup
Normally, CMOS setup is needed when the system hardware is not consistent
with the information contained in the CMOS RAM, whenever the CMOS RAM has
lost power, or the system features need to be changed.
- 29 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
3.3 BIOS Setup Utility
Once you enter the AMI BIOS Setup Utility, the Main Menu will appear on
the screen. The main menu allows you to select from several setup functions
and one exit. Use arrow keys to select among the items and press <Enter> to
accept or enter the submenu.
3.4 Main
The Main menu is the first screen that you will see when you enter the
BIOS Setup Utility.
BIOS Information
Displays the detected BIOS information.
Memory Information
Displays the detected system memory information.
System Date
The date format is <day>, <month>, <date>, <year>. Day displays a day, from
Sunday to Saturday. Month displays the month, from January to December. Date
displays the date, from 1 to 31. Year displays the year, from 1999 to 2099.
- 30 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
System Time
The time format is <hour>, <minute>, <second>. The time is based on the
24-hour military-time clock. For example, 1 p.m. is 13:00:00. Hour displays hours
from 00 to 23. Minute displays minutes from 00 to 59. Second displays seconds
from 00 to 59.
3.5 Advanced
The Advanced menu allows you to configure your system for basic operation.
Some entries are defaults required by the system board, while others, if enabled,
will improve the performance of your system or let you set some features
according to your preference.
Setting incorrect field values may cause the system to malfunction.
Launch PXE OpROM
Enables or disables the boot option for legacy network devices.
- 31 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
CPU Configuration
This section is used to configure the CPU.
CPU Configuration
Displays the detected CPU information.
Active Processor Cores
This field is used to enter the number of cores to enable in each rocessorpackage.
Limit CPUID Maximum
The CPUID instruction of some newer CPUs will return a value greater than 3.
The default is Disabled because this problem does not exist in the Windows
series operating systems. If you are using an operating system other than
Windows, this problem may occur. To avoid this problem, enable this field to limit
the return value to 3 or lesser than 3.
Execute Disable Bit
When this field is set to Disabled, it will force the XD feature flag to always return
to 0. XD can prevent certain classes of malicious buffer overflow attacks when
combined with a supporting OS (Windows Server 2003 SP1, Windows XP SP2,
SuSE Linux 9.2, RedHat Enterprise 3 Update 3.)
- 32 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
Hardware Prefetcher
Tuns on or off the Mid level Cache (L2) streamer prefetcher. The options are
Enabled and Disabled.
Adjacent Cache Line Prefetch
Turns on or off prefetching of adjacent cache lines. The options are Enabled and
Disabled.
Intel Virtualization Technology
When this field is set to Enabled, the VMM can utilize the additional hardware
capabilities provided by Vanderpool Technology.
Power Technology
Configures the power management features.
Local x2APIC
Enables or disables the Local x2APIC. Some OSes doesn’t support this feature.
Long Duration Power Limit
Configures the long duration power limit in Watts.
Long Duration Maintained
Time window when the long duration power is maintained.
Short Duration Power Limit
Configures the short duration power limit in Watts.
- 33 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
SATA Configuration
This section is used to configure SATA.
SATA Mode
IDE Mode
This option configures the Serial ATA drives in IDE mode.
RAID Mode
This option enables the RAID function for Serial ATA drives.
AHCI Mode
This option configures the Serial ATA drives in AHCI mode.
Serial-ATA Controller 0 / Serial-ATA Controller 1
Configures the Serial ATA controller to Compatible or Enhanced mode.
- 34 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
IDE Mode
RAID Mode
HOT Plug
SATA Ports Hot Plug Support.
- 35 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
AHCI Mode
Aggressive Link Power Management Support
For Cougar Point B0 stepping onwards.
Staggered Spin-up
AHCI Supports Staggered Spin-up.
External SATA Port
eSATA Ports Support.
HOT Plug
SATA Ports Hot Plug Support.
- 36 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
Intel IGD SWSCI OpRegion
This section is used to configure the Intel graphics display.
DVMT Mode Select
Selects the DVMT mode used by the internal graphics device.
DVMT/FIXED Memory
Selects the DVMT/FIXED mode memory size used by the internal graphics
device.
IGD - Boot Type
Selects the video device that will be activated during POST. This will not
affect any external graphics that may be present.
- 37 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
USB Configuration
This section is used to configure the USB
USB Configuration
Displays the detected USB devices.
Legacy USB Support
Enable
Enables Legacy USB
Auto
Disables support for Legacy when no USB devices are connected
Disable
Keeps USB devices available only for EFI applications.
EHCI Hand-Off
This is a workaround for OSes that does not support EHCI hand-off. The EHCI
ownership change should be claimed by the EHCI driver.
Device Reset Timeout
Selects the USB mass storage device’s start unit command timeout.
- 38 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
Super IO 2 Configuration
This section is used to configure the serial and parallel ports.
Super IO Chip 2
Displays the Super I/O chip used on the board
Serial Port 0/1 Configuration
This section is used to configure the serial ports.
- 39 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
Serial Port
Enables or disables the serial port.
Change Settings
Selects an optimal settings for the Super IO device.
Onboard Serial Port 0/1 Mode
Change the serial port mode.
Select <RS232> or <RS422> or <RS485> mode.
Onboard Serial Port Max Baud Rate
Selects the maximum baud rate of the serial port.
- 40 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
H/W Monitor
This section is used to configure the hardware monitoring events such as
temperature, fan speed and voltages.
FAN Setting
Configures the cooling fan.
System Temperature 1 to CPU Temperature
Detects and displays the internal temperature of the system and the current
temperature of the CPU
CPU Fan Speed to System Fan2 Speed
Detects and displays the current fan speed in RPM (Revolutions Per
Minute).
CPU:Vcore to +3.3V
Detects and displays the output voltages.
- 41 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
AMT Configuration
This section is used to configure AMT.
AMT
Enables or disables the AMT function.
Unconfigure AMT/ME
Select Enabled to unconfigure the AMT/ME function without the need for a
password.
Watchdog Timer
Enables or disables the Watchdog Timer function.
OS Watchdog Timer
Selects the time interval of the OS Watchdog Timer.
BIOS Watchdog Timer
Selects the time interval of the BIOS Watchdog Timer.
- 42 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
3.6 Chipset
This section gives you functions to configure the system based on the specific
features of the chipset. The chipset manages bus speeds and access to
system memory resources.
North Bridge
This section is used to configure the north bridge features.
- 43 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
VT-d
The options are Enabled and Disabled.
IGD Memory
Selects the internal graphics device’s shared memory size.
South Bridge
This section is used to configure the south bridge features.
SMBus Controller
Enables or disables the SMBus controller.
GbE Controller
Enables or disables the Gigabit LAN controller.
Wake On Lan From S5
When enabled, it allows the system to wake up from S5 via the network
LAN.
- 44 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
Restore AC Power Loss
Power Off
When power returns after an AC power failure, the system’s
power is off. You must press the Power button to power-on the
system.
Power On
When power returns after an AC power failure, the system will
automatically power-on.
Last State
When power returns after an AC power failure, the system will
return to the state where you left off before power failure occurs.
If the system’s power is off when AC power failure occurs, it will
remain off when power returns. If the system’s power is on when
AC power failure occurs, the system will power-on when power
returns.
Azalia HD Audio
Enables or disables the Azalia HD audio.
Azalia Internal HDMI Codec
Enables or disables the HDMI feature.
High Precision Timer
Enables or disables the high precision event timer.
USB Configuration
- 45 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
All USB Devices
Enables or disables all USB devices.
EHCI Controller 1 and EHCI Controller 2
Enables or disables the Enhanced Host Controller Interface (USB 2.0).
Intel ME Configuration
ME Subsystem
The options are Enabled and Disabled.
ME Temporary Disable
The options are Enabled and Disabled.
End of the POST Message
The options are Enabled and Disabled.
Execute MEBx
The options are Enabled and Disabled.
MEBx Mode
The options are Normal, Hidden Ctrl + P and Enter MEBx Setup.
- 46 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
3.7 Boot
Setup Prompt Timeout
Selects the number of seconds to wait for the setup activation key.
65535(0xFFFF) denotes indefinite waiting.
Bootup NumLock State
This allows you to determine the default state of the numeric keypad. By
default, the system boots up with NumLock on wherein the function of the
numeric keypad is the number keys. When set to Off, the function of the
numeric keypad is the arrow keys.
Quiet Boot
Enabled
Displays OEM logo instead of the POST messages.
Disabled
Displays normal POST messages.
Fast Boot
Enables or disables the fast boot.
- 47 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
Gate A20 Active
Upon Request
GA20 can be disabled using BIOS services.
Always
Does not allow disabling GA20. This option is useful when an
RT code is executed above 1MB.
Option ROM Messages
Selects the display mode for Option ROM. The options are Force BIOS and
Keep Current.
Interrupt 19 Capture
When enabled, it allows the optional ROM to trap interrupt 19.
- 48 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
3.8 Security
Administrator Password
Sets the administrator password.
User Password
Sets the user password.
- 49 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
3.9 Save & Exit
Save Changes and Exit
To save the changes and exit the Setup utility, select this field then press <Enter>.
A dialog box will appear. Confirm by selecting Yes. You can also press <F10> to
save and exit Setup.
Discard Changes and Exit
To exit the Setup utility without saving the changes, select this field then press
<Enter>. You may be prompted to confirm again before exiting. You can also
press <ESC> to exit without saving the changes.
Save Changes and Reset
To save the changes and reset, select this field then press <Enter>. A dialog box
will appear. Confirm by selecting Yes.
Discard Changes and Reset
To exit the Setup utility without saving the changes, select this field then press
<Enter>. You may be prompted to confirm again before exiting.
Discard Changes
To discard the changes, select this field then press <Enter>. A dialog box will
appear. Confirm by selecting Yes to discard all changes made and restore the
previously saved settings.
- 50 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
Chaper 4 huperVision Software Installation
4.1 Easy Steps to Install Software
Installation
1. Insert CDROM You will see the Auto Run start up like following Picture
2. Press [huperVision] Button
Now start huperVision installation program, The first dialogue box pop-out
and please select your installation languages and press [OK] button
- 51 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
Please wait until the following dialogue appears. Please press [Next]
button to proceed.
3. Now you see the License agreement, Please take a look if you want, or
directly select [I accept the terms in the license agreement] then press
[Next] button to proceed.
- 52 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
4. The destination folder selection appears. Please directly press [Next]
button to use the default folder.
5. Selection of interface type and channel version.
Select black (default) to use huperVision new interface style or silver to use
huperVision traditional interface style.
Please select 16ch version to fit all series of huperVision capture cards. If
you want to setup a 32CH machine, please select 32ch version which will
use dual VGA output.
Meanwhile, select correct Video standard (NTSC/PAL) and press [Next] to
proceed. (This option can be adjusted after setup)
- 53 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
6. Now Press the [Install] button to start full installation with capture card
driver setup.
Press [Finish] to end installation. Please press [Yes] to initial huperVision site
server program when the installer asking for a reboot.
- 54 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
4.2 Simple Steps to Start Recording
Please follow the steps below to start recording.
1. After reboot (Manually), huperVision site server program is launching.
You will see a pop-up warning message; this is a notification that you have
not specified a recording path to record.
2. You can press the [Hammer] Button
to display the general page of
preference.
3. Press the [Add…] button to add a new folder to store your recording data
files.
- 55 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
4. Press [Browser…] button in the Add Storage dialogue box.
5. You can create a new folder in drive E; e.g. E:\DATA (D:\DATA indicates
there is a DATA folder under Drive D.)
So, you select the Drive E icon and press the button [Make New Folder]
And input the new folder name “DATA”, then press [OK].
- 56 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
6. The result will be shown when back to the Add Storage dialogue box.
Please press [OK] button to save the decision.
Note:
Please keep the all 16 cameras be checked even if you don’t have that much
cameras.
Please also do NOT change the Allocated record space value by its automatic
decision.
- 57 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
7. After Create the folder and press the [OK] button of the Preference page.
Congratulations! You start to record videos.
8. The R LED turns green at upper right side, indicates that available
channels are recording now.
- 58 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
4.3 Simple Steps to Playback Recordings
1. Launch the huperVision Record Player program by clicking the icon
2. You will see the following full screen program to cover the current
huperVision Live view. Don’t worry. The Live View and recording task are
still working at the background.
3. You have to select which channel you want to playback with, or select All
Channels to playback all available channels at the same time.
- 59 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
4. After you select the channel you want to playback, it shows a list of time
mark for today’s recording. Please select a Time mark to load the Video
records.
5. All the video available channels will show the first Image in the Video split
area, after the video load progress bar running to the end.
You can now press the Play Button to start playback selected channel
recordings.
6. If you want to select different Channel to playback, please repeat from Step
3 to Step 5.
7. You can press the [Power off]
button to Exit this Playback program
any time.
Note:
Press this Power off button will NOT close the running huperVision site server.
There is also a protection for accident press the huperVision site server power
button, a Confirm dialogue box will show before it really shut down the
huperVision site server main program.
- 60 -
huperVision 4000 Vento2 DSS Server Board
Quick Guide
Now you are ready to use huperVision IVS system, for more operation guide on
Intelligent Video Functions, please refer to full Users Manual.
Press the [Document] on the Installation CDROM autorun program.
You will be able to open the Document. Before you load this document, please
ensure your system have already Acrobat Reader program installed.
The Acrobat Reader program is included in the Installation CDROM
E:\English\Doc\aar.exe
- 61 -
Download PDF
Similar pages