projector pj200/250 ust dlp

PROJECTOR PJ200/250
UST DLP
English
Table of Contents
Table of Contents ............................1
Usage Notice ...................................2
Safety Information ...............................2
Precautions .........................................3
Eye Safety Warnings ..........................5
Product Features ................................5
Introduction ......................................6
Package Overview ..............................6
Product Overview ...............................7
Main Unit.............................................. 7
Control Panel ....................................... 8
Input/Output Connections .................... 9
Remote Control.................................. 10
Installation ..................................... 11
Connecting the Projector ..................11
Removing and Attaching the
Cable Cover ....................................... 11
Connect to Computer/Notebook ........ 12
Connect to Video Sources ................. 13
Powering the projector On / Off ........14
Powering On the Projector................. 14
Powering Off the Projector................. 15
Warning Indicator............................... 15
SETUP | Security ............................... 40
SETUP | Advanced ............................ 42
SETUP | Network ............................... 43
OPTIONS........................................... 46
OPTIONS | Advanced ........................ 48
OPTIONS | Lamp Settings................. 49
Appendices ....................................50
Troubleshooting ................................50
Replacing the lamp ...........................55
Replacing and cleaning the
dust filter ...........................................57
Compatibility Modes .........................58
Computer Compatibility ..................... 58
Video Compatibility ............................ 59
RS232 Commands and Protocol
Function List .....................................60
RS232 Pin Assignments .................... 60
RS232 Protocol Function List ............ 61
Wall Mount Installation ......................65
Regulation & Safety Notices .............66
Repair Service and Contacts ........... 68
Adjusting the Projected Image ..........16
Adjusting the Projector’s Height ........ 16
Adjusting the Projector’s Focus ......... 17
Adjusting Projection Image Size ........ 17
User Controls ................................19
Control Panel & Remote Control ......19
Control Panel ..................................... 19
Remote Control.................................. 20
On-screen Display Menus ................25
How to operate ................................. 25
Menu Tree.......................................... 26
IMAGE ............................................... 28
IMAGE | Advanced ............................ 30
DISPLAY ............................................ 32
DISPLAY | 3D ................................... 35
SETUP ............................................... 36
SETUP | Signal (RGB) ....................... 39
1
English
Usage Notice
Safety Information
The lightning flash with arrow head within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH
VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE
CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
Class B emissions limits
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Important Safety Instruction
1. Do not block any ventilation openings. To ensure reliable operation of
the projector and to protect from over heating, it is recommended to
install the projector in a location that does not block ventilation. As an
example, do not place the projector on a crowded coffee table, sofa,
bed, etc. Do not put the projector in an enclosure such as a book case
or a cabinet that restricts air flow.
2. Do not use the projector near water or moisture. To reduce the risk
of fire and/or electric shock, do not expose the projector to rain or
moisture.
3. Do not install near heat sources such as radiators, heaters, stoves or
any other apparatus such as amplifiers that emits heat.
4. Clean only with dry cloth.
5. Only use attachments/accessories specified by the manufacturer.
6. Do not use the unit if it has been physically damaged or abused.
Physical damage/abuse would be (but not limited to):
 Unit has been dropped.
 Power supply cord or plug has been damaged.
 Liquid has been spilled on to the projector.
 Projector has been exposed to rain or moisture.
 Something has fallen in the projector or something is loose inside.
Do not attempt to service the unit yourself. Opening or removing covers
may expose you to dangerous voltages or other hazards. Please call
Optoma before you send the unit for repair.
7. Do not let objects or liquids enter the projector. They may touch
dangerous voltage points and short out parts that could result in fire or
electric shock.
8. See projector enclosure for safety related markings.
9. The unit should only be repaired by appropriate service personnel.
English
2
Usage Notice
Precautions
Please follow all warnings, precautions and
maintenance as recommended in this user’s
guide.
▀■ Warning- Do not look into the projector’s lens when the lamp is
on. The bright light may hurt and damage your eyes.
▀■ Warning- To reduce the risk of fire or electric shock, do not
expose this projector to rain or moisture.
▀■ Warning- Please do not open or disassemble the projector as
this may cause electric shock.
▀■ Warning- When replacing the lamp, please allow the unit to
cool down. Follow instructions as described on pages
57-58.
▀■ Warning- This projector will detect the life of the lamp itself.
Please be sure to change the lamp when it shows
warning messages.
▀■ Warning- Reset the “Lamp Reset” function from the on-screen
display “OPTIONS | Lamp Settings” menu after
replacing the lamp module (refer to page 51).
▀■ Warning- When switching the projector off, please ensure
 When the lamp
reaches the end
of its life, the projector will not turn
back on until the
lamp module has
been replaced.
To replace the
lamp, follow the
procedures listed
under “Replacing
the Lamp” section
on pages 57-58.
the cooling cycle has been completed before
disconnecting power. Allow 90 seconds for the
projector to cool down.
▀■ Warning- Do not use lens cap when projector is in operation.
▀■ Warning- When the lamp is approaching the end of its lifetime,
the message “Lamp Warning: Lamp life exceeded.”
will show on the screen. Please contact your local
reseller or service center to change the lamp as soon
as possible.
▀■ Warning- Do not look into or point the laser pointer on your
remote control into your or someone’s eyes. Laser
pointer can cause permanent damage to eyesight.
3
English
Usage Notice
Do:
 Turn off and unplug the power plug from the AC outlet before
cleaning the product.
 Use a soft dry cloth with mild detergent to clean the display
housing.
 Disconnect the power plug from AC outlet if the product is
not being used for a long period of time.
Do not:
 Block the slots and openings on the unit provided for
ventilation.
 Use abrasive cleaners, waxes or solvents to clean the unit.
 Use under the following conditions:
- In extremely hot, cold or humid environments.
 Ensure that the ambient room temperature is within
5 - 35°C.
 Relative Humidity is 5 - 35°C, 80% (Max.),
non-condensing.
- In areas susceptible to excessive dust and dirt.
- Near any appliance generating a strong magnetic field.
- In direct sunlight.
English
4
Usage Notice
Eye Safety Warnings
▀■ Avoid staring/facing directly into the projector beam at all
times. Keep your back to the beam as much as possible.
▀■ When projector is used in a classroom, adequately supervise
students when they are asked to point out something on the
screen.
▀■ In order to minimize the lamp power, use room blinds to
reduce ambient light levels.
Product Features
▀■ XGA (1024x768) Native resolution /
WXGA (1280x800) Native resolution
▀■ HD compatible – 1080p supported
 Monitor loop
through only support in VGA1-In/
SCART/YPbPr.
▀■ VGA monitor loop through
(works on standby mode > 1W)
▀■ BrilliantColorTM Technology
▀■ Security Bar and Kensington Lock
▀■ RS232 control
▀■ Rapid shutdown
▀■ Built-in speakers
▀■ Network support
5
English
Introduction
Package Overview
Unpack and inspect the box contents to ensure
all parts listed below are in the box. If something
is missing, please contact your nearest customer
service center.
Projector with lens cap
 Due to different
applications in
each country,
some regions
may have
different
accessories.
2 × AAA Batteries
Documentation :
 User’s Manual
 Warranty Card
 Quick Start Card
 WEEE Card
(for EMEA only)
English
6
Power Cord 1.8m
IR Remote Control
VGA Cable 1.8m
Introduction
Product Overview
Main Unit
12
1
3
11
2
4
5
7
6
AUDIO1-IN
(VGA1/VGA2)
RS-232
12V OUT
VIDEO
L
S-VIDEO
VGA1-IN / SCART / YPbPr
VGA-OUT
HDMI
SERVICE
RJ-45
R
AUDIO OUT
MIC
AUDIO2-IN (S-VIDEO/VIDEO)
VGA2-IN / YPbPr
15
5
9
5
8
10
2
13 14
1.
2.
3.
4.
5.
6.
7.
8
Control Panel
IR Receivers
Cable Cover
Speaker
Tilt-Adjustment Feet
Mirror Cover
Input / Output Connections
Power Socket
9.
10.
11.
12.
13.
14.
15.
Focus Lever
Lens
Ventilation (inlet)
Ventilation (outlet)
KensingtonTM Lock Port
Security Bar
Dust filter
7
English
Introduction
Control Panel
1
6
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
English
8
2
3
4
7
8
Lamp LED
Temp LED
Source
Re-Sync
Help
Power/Standby button and LED
Enter
Keystone Correction
Four Directional Select Keys
Menu
9
5
10
Introduction
Input/Output Connections
1
12V OUT
2
3
4
5
AUDIO1-IN
(VGA1/VGA2)
RS-232
VIDEO
S-VIDEO
12V OUT
L
6
7
VGA1-IN / SCART / YPbPr
VGA-OUT
8
HDMI
9
SERVICE
RJ-45
R
AUDIO OUT
10
MIC
11
AUDIO2-IN (S-VIDEO/VIDEO)
VGA2-IN / YPbPr
14
12
15
13
 Monitor loop
through only support in VGA1-In/
SCART/YPbPr.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
12V Trigger Relay (12V, 250mA)
3.5mm Mini Jack Audio1 Input for VGA1/VGA2
3pin Mini-din RS232
Composite Video Input
S-Video Input
VGA1/SCART/YPbPr Input
VGA-Out (monitor loop through)
HDMI v1.3 Input
5pin Mini-USB for firmware upgrade
3.5mm Audio Output (Variable)
3.5mm Microphone Input
Left/Right RCA Audio2 Input
Power Socket
VGA2/YPbPr Input
RJ45
9
English
Introduction
Remote Control
1
2
 The interface
is subject to
model’s specifications.
24
12
3
13
4
14
5
15
6
16
7
17
8
18
9
19
10
20
11
21
English
10
22
23
1. LED Indicator
2. Power On/Off
3. Four Directional
Select Keys
4. Mouse Right Click
5. Page Up
6. Re-Sync
7. Page Down
8. Volume +/9. 3D
10. AV mute
11. Video
12. PC/Mouse control
13. Mouse Left Click
14. Enter/Help
15. Source
16. Keystone +/17. Menu
18. Brightness
19. HDMI
20. S-Video
21. Numbered keypad
(for password input)
22. Freeze
23. VGA
24. Laser Pointer
Installation
Connecting the Projector
Removing and Attaching the Cable Cover
Cable Cover
2
1
Procedure for Removing and Attaching
the Cable Cover:
1. Unscrew the screw on the cable cover. 1
2. Lift up and remove the cable cover. 2
Install the cable cover by reversing the previous steps.
11
English
Installation
Connect to Computer/Notebook
+12V Output
3
4
Audio Output
MOLEX
10
5
6
7
2
molex
AUDIO1-IN
(VGA1/VGA2)
RS-232
12V OUT
VGA1-IN / SCART / YPbPr
VGA-OUT
HDMI
SERVICE
RJ-45
R
AUDIO OUT
MIC
AUDIO2-IN (S-VIDEO/VIDEO)
VGA2-IN / YPbPr
PS50426E
 (*) Optional
accessory
1
S-VIDEO
R
 Due to the
difference in
applications
for each
country, some
regions may
have different
accessories.
VIDEO
L
8
9
1....................................................................................................Power Cord
2......................................................................................*Audio Output Cable
3.........................................................................................*Audio Input Cable
4................................................................................................*RS232 Cable
5.....................................................................................................VGA Cable
6..................................................................................................*HDMI Cable
7....................................................................................................*USB Cable
8..............................................................................................*Network Cable
9........................................................................................*VGA Output Cable
10.............................................................................................. *12V DC Plug
English
12
Installation
Connect to Video Sources
S-Video Output
Composite Video Output
4
DVD Player, Set-top Box,
HDTV receiver
+12V Output
12
1
5
6
Audio Output
7
AUDIO1-IN
(VGA1/VGA2)
3
VIDEO
L
S-VIDEO
VGA1-IN / SCART / YPbPr
VGA-OUT
HDMI
SERVICE
RJ-45
R
AUDIO OUT
MIC
AUDIO2-IN (S-VIDEO/VIDEO)
9
VGA2-IN / YPbPr
E62405SP
R
2
RS-232
12V OUT
8
10
 Due to the
difference in
applications
for each
country, some
regions may
have different
accessories.
 (*) Optional
accessory
DVD Player,
Set-top Box,
HDTV receiver
11
1.................................................................................*Audio Cable RCA/RCA
2........................................................................................ *Microphone Cable
3.................................................................................*Audio Cable Jack/RCA
4................................................................................*Composite Video Cable
5.............................................................................................. *S-Video Cable
6................................................................................... *SCART/VGA Adaptor
7.....................................................................................................VGA Cable
8..................................................................................................*HDMI Cable
9....................................................................................................Power Cord
10..............................................*15-Pin to 3 RCA Component/HDTV Adaptor
11. ..........................................................................*3 RCA Component Cable
12.............................................................................................. *12V DC Plug
13
English
Installation
Powering the projector On / Off
Powering On the Projector
 When Power mode
(Standby) is set
to Eco (<1W), the
VGA output, Audio
pass-through
and RJ45 will be
deactivated when
the projector is in
standby.
1. Securely connect the power cord and signal cable. When
connected, the POWER/STANDBY LED will turn Amber.
2. Turn on the lamp by pressing “ ” button either on the top of
the projector or on the remote. The POWER/STANDBY LED
will now turn Green.
The startup screen will display in approximately 10 seconds.
The first time you use the projector, you will be asked to
select the preferred language and power saving mode.
3. Turn on and connect the source that you want to display
on the screen (computer, notebook, video player, etc). The
projector will detect the source automatically. If not, push
menu button and go to “OPTIONS”.
Make sure that the “Source Lock” has been set to “Off”.
 If you connect multiple sources at the same time, press the
“SOURCE” button on the control panel or direct source keys
on the remote control to switch between inputs.
 Turn on the
projector first and
then select the
signal sources.
English
14
or
Installation
Powering Off the Projector
1. Press the “ ” button on the remote control or
on the control panel to turn off the projector.
The following message will be displayed on the screen.
Press the “ ” button again to confirm otherwise the
message will disappear after 15 seconds. When you
press the “ ” button for the second time, the projector will
display countdown timer and will shut down.
2. The cooling fans continue to operate for about 10 seconds
for cooling cycle and the POWER/STANDBY LED will
Flash Green. When the POWER/STANDBY LED lights
solid Amber, the projector has entered standby mode.
If you wish to turn the projector back on, you must wait
until the projector has completed the cooling cycle and
has entered standby mode. Once in standby mode, simply
press “ ” button to restart the projector.
3. Disconnect the power cord from the electrical outlet and
the projector.
4. Do not turn on the projector immediately following a power
off procedure.
Warning Indicator
When the warning indicators (see below) come on,
the projector will automatically shutdown:
 Contact the
nearest service
center if the
projector displays
these symptoms.
See pages
68-69 for more
information.
 “LAMP” LED indicator is lit red and if “POWER/STANDBY”
indicator flashes amber.
 “TEMP” LED indicator is lit red and if “POWER/STANDBY”
indicator flashes amber. This indicates the projector has
overheated. Under normal conditions, the projector can be
switched back on.
 “TEMP” LED indicator flashes red and if “POWER/STANDBY” indicator flashes amber.
Unplug the power cord from the projector, wait for 30 seconds
and try again. If the warning indicator light up again, please
contact your nearest service center for assistance.
15
English
Installation
Adjusting the Projected Image
Adjusting the Projector’s Height
The projector is equipped with elevator feet for adjusting
the image height.
1. Locate the adjustable foot you wish to modify on the
underside of the projector.
2. Rotate the adjustable ring clockwise to raise the projector
or counter clockwise to lower it. Repeat with the remaining
feet as needed.
Tilt-Adjustment Feet
Tilt-Adjustment Ring
English
16
Installation
Adjusting the Projector’s Focus
To focus the image, rotate the focus ring until the image is clear.
 XGA series: The projector will focus at distances from 1.58
to 2.17 feet (475 to 662 mm).
 WXGA series: The projector will focus at distances from 1.58
FOCUS
to 2.17 feet (495 to 661 mm).
Focus Ring
Adjusting Projection Image Size
 XGA series: Projection Image Size from 63” to 85” (1.60 to
2.16 meters).
 WXGA series: Projection Image Size from 77” to 100” (1.96
to 2.54 meters).
17
English
Installation
(W)
B=>Vertical distance between lens
center and screen center
C,E=>Throw distance
D=>Vertical distance between lens
center and bottom of screen (top of
screen for ceiling mount)
α=>Throw angle
(H)
Screen Center
Sc
ree
nD
iag
ona
l
(B)
Throw Angle (α)
(D)
Lens Center
(C)
(E)
XGA
Screen Size
Diagonal
Width (W)
(B)
Height (H)
(C)
(D)
(α)
(E)
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
63
1600
50
1280
38
960
29
749
5
133
11
269
19
475
degree
55.3
65
1651
52
1321
39
991
30
773
6
150
11
277
19
492
55.3
70
1778
56
1422
42
1067
33
832
8
192
12
299
21
534
55.3
75
1905
60
1524
45
1143
35
892
9
235
13
320
23
577
55.3
77
1956
62
1565
46
1173
36
915
10
251
13
329
23
594
55.3
80
2032
64
1626
48
1219
37
951
11
277
13
341
24
619
55.3
85
2159
68
1727
51
1295
40
1010
13
320
14
363
26
662
55.3
WXGA
Screen Size
Diagonal
Width (W)
(B)
Height (H)
(C)
(D)
(α)
(E)
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
77
1956
65
1659
41
1037
31
777
6
153
10
259
19
495
degree
55.3
80
2032
68
1723
42
1077
32
808
7
174
11
269
20
516
55.3
85
2159
72
1831
45
1144
34
858
8
214
11
286
22
568
55.3
87.2
2215
74
1878
46
1174
35
880
9
226
12
293
22
569
55.3
90
2286
76
1939
48
1212
36
909
10
246
12
303
23
588
55.3
95
2413
81
2046
50
1279
38
959
11
283
13
320
25
625
55.3
100
2540
85
2154
53
1346
40
1010
13
319
13
337
26
661
55.3
 This table is for user’s reference only.
English
18
User Controls
Control Panel & Remote Control
Control Panel
Using the Control Panel
Power/
Standby button and LED
Refer to the “Power On/Off the Projector” section on
pages 14-15.
Indicate the projector’s status.
RE-SYNC
Automatically synchronize the projector to the input
source.
Enter
Confirm your item selection.
SOURCE
Press “SOURCE” to select an input signal.
Menu
Press “Menu” to launch the on-screen display
(OSD) menu. To exit OSD, Press “Menu” again.
Four Directional
Select Keys
Use
to select items or make adjustments to your selection.
Keystone
Use
to adjust image distortion caused by
tilting the projector. (±40 degrees)
HELP
Help Menu (refer to page 22).
Lamp LED
Indicate the projector’s lamp status.
Temp LED
Indicate the projector’s temperature status.
19
English
User Controls
Remote Control
Using the Remote Control
Power
Refer to the “Power On/Off the Projector”
section on pages 14-15.
L Button
Mouse left click.
R Button
Mouse right click.
Page +
Use this button to page up.
Page -
Use this button to page down.
Enter
English
20
/ Help
Confirm your item selection.
Help Menu (refer to page 22).
Source
Press “Source” to select an input signal.
Re-SYNC
Automatically synchronizes the projector to
the input source.
Four Directional
Select Keys
Use
to select items or make
adjustments to your selection.
Keystone +/-
Adjust image distortion caused by tilting the
projector.
Volume +/-
Adjust to increase / decrease the volume.
Brightness
Adjust the brightness of the image.
3D
Press the “3D” to turn the 3D OSD menu
on/off.
Menu
Press “Menu” to launch the on-screen
display (OSD) menu. To exit OSD, press
“Menu” again.
HDMI
Press “HDMI” to choose HDMI source.
Freeze
Press “Freeze” to pause the screen image.
Press this button again to unlock.
User Controls
Using the Remote Control
AV mute
Momentarily turns off/on the audio and
video.
S-Video
Press “S-Video” to choose S-Video source.
VGA
Press “VGA” to choose VGA sources.
Video
Press “Video” to choose Composite video
source.
21
English
User Controls
Using the HELP button
The HELP function ensures easy setup and operation.
 Press the “?” button on the remote control or press the
“HELP” button on the control panel to open the Help Menu.
English
22
User Controls
 Help menu button functions only when no input source
is detected.
 Please refer to the
“Troubleshooting”
section on pages
52-56 for more
details.
 If input source is detected and help button is pressed, the
following pages will appear to help diagnose any problems.
23
English
User Controls
English
24
User Controls
On-screen Display Menus
The Projector has multilingual On-screen Display menus that
allow you to make image adjustments and change a variety of
settings.
How to operate
1. To open the OSD menu, press “Menu” on the Remote Control or
Projector Keypad.
2 When OSD is displayed, use
keys to select any item in the
main menu. While making a selection on a particular page, press
or “Enter” key to enter sub menu.
3. Use
using
keys to select the desired item and adjust the settings
key.
4. Select the next item to be adjusted in the sub menu and adjust as
described above.
5. Press “Enter” to confirm, and the screen will return to the main
menu.
6. To exit, press “MENU” again. The OSD menu will close and the
projector will automatically save the new settings.
Main Menu
Sub Menu
Settings
25
English
User Controls
Menu Tree
Main Menu
Sub Menu
Image
Display Mode
Settings
Brightness
Presentation / Bright / Movie / sRGB /
Blackboard / Classroom / User / 3D
-50~50
Contrast
-50~50
Sharpness
1~15
#1
Color
-50~50
#1
Tint
-50~50
Advanced
Display
Gamma
Film / Video / Graphics / PC
BrilliantColor™
0~10
Color Temp.
Warm / Medium / Cold
Color Settings
Color Space
Red Gain / Green Gain / Blue Gain / Red
Bias / Green Bias / Blue Bias / Cyan /
Magenta / Yellow / Reset / Exit
AUTO / RGB / YUV
Input Source
VGA1 / VGA2 / Video / S-Video / HDMI
Image AI
Exit
On / Off
Format
#2
#3
Edge Mask
Zoom
H Image Shift
V Image Shift
V Keystone
3D
#4
Setup
#3
3D
3D Sync. Invert
Exit
4:3 / 16:9-I / 16:9-II / Native / AUTO
4:3 / 16:9 or 16:10 / LBX / Native / AUTO
0~10
-5~25 (80%~200%)
-50~50
-50~50
-40~40
Off / DLP-Link / IR
On / Off
Language
English / Deutsch / Français / Italiano /
Español / Português / Svenska /
Nederlands / Norsk/Dansk / Polski /
/
/ Magyar /
Suomi /
/
/
eština /
/
/
/
/ Türkçe / Vi t /
Bahasa Indonesia
Screen Type
Projection
16:10 / 16:9
Menu Location
#5
Signal
Security
English
26
Automatic
Phase (VGA)
Frequency (VGA)
H. Position (VGA)
V. Position (VGA)
Exit
Security
Security Timer
Change Password
Exit
On / Off
0~31
-5~5
-5~5
-5~5
On / Off
Month / Day / Hour
User Controls
Main Menu
Sub Menu
Setup
Projector ID
Mute
Volume
Audio Input
Advanced
Network
Options
Source Lock
High Altitude
Information Hide
Keypad Lock
Background Color
IR Receiver
Advanced
Lamp Settings
Settings
Logo
Logo Capture
Closed Captioning
Exit
Network State
DHCP
IP Address
Subnet mask
Gateway
DNS
Apply
Exit
Front Receiver
Top Receiver
Direct Power On
Auto Power Off (min.)
Sleep Timer (min.)
Power Mode (Standby)
Exit
Lamp Hours
Lamp Reminder
Brightness Mode
Lamp Reset
Exit
Reset Dust Filter
Reset
0~99
On / Off
0~10
#6
Default / Audio1(Phone jack) / Audio2
(RCA R/L)
Optoma / Neutral / User
Off / CC1 / CC2
Yes / No
On / Off
On / Off
On / Off
On / Off
Black / Red / Blue / Green / White
On / Off
On / Off
On / Off
0~180
0~995
Eco. / Active
On / Off
STD / Bright / Image AI
Yes / No
Yes / No
 Please note that the on-screen display (OSD) menus vary according to the
signal type selected and the projector model you are using.
 (#1) “Color” and “Tint” are only supported in Video mode.
 (#2) For XGA model only.
 (#3) For WXGA model only. 16:9 or 16:10 depend on “Screen Type” setting.
 (#4) “3D Sync Invert” is only available when 3D is enabled.
 (#5) “Signal” is only supported in Analog VGA (RGB) signal.
 (#6) MIC volume can also be controlled by “Setup  Volume” in OSD.
27
English
User Controls
IMAGE
Display Mode
There are many factory presets optimized for various types of
images.
 Presentation: Good color and brightness from PC input.
 Bright: Maximum brightness from PC input.
 Movie: For home theater.
 sRGB: Standardised accurate color.
 Blackboard: This mode should be selected to achieve optimum
color settings when projecting onto a blackboard (green).
 Classroom: This mode is recommended for projecting in a
classroom.
 User: User’s settings.
 3D: Recommand setting for 3D mode enabled. Any further ad-
justments by the user in 3D will be saved in this mode for further
use.
Brightness
Adjust the brightness of the image.
 Press the
 Press the
Contrast
to darken image.
to lighten the image.
The contrast controls the degree of difference between the lightest
and darkest parts of the picture.
 Press the
 Press the
English
28
to decrease the contrast.
to increase the contrast.
User Controls
Sharpness
Adjust the sharpness of the image.
 Press the
 Press the
Color
 “Color” and “Tint”
functions are only
supported under
Video mode.
to decrease the sharpness.
to increase the sharpness.
Adjust a video image from black and white to fully saturated color.
 Press the
 Press the
Tint
to decrease the amount of saturation in the image.
to increase the amount of saturation in the image.
Adjust the color balance of red and green.
 Press the
 Press the
to increase the amount of green in the image.
to increase the amount of red in the image.
29
English
User Controls
IMAGE | Advanced
Gamma
This allows you to choose a degamma table that has been
fine-tuned to bring out the best image quality for the input.
 Film: for home theater.
 Video: for video or TV source.
 Graphics: for image source.
 PC: for PC or computer source.
BrilliantColor™
This adjustable item utilizes a new color-processing algorithm and
system level enhancements to enable higher brightness while
providing true, more vibrant colors in picture. The range is from
“0” to “10”. If you prefer a stronger enhanced image, adjust toward
the maximum setting. For a smoother, more natural image, adjust
toward the minimum setting.
Color Temp
If set to cold temperature, the image looks more blue. (cold image)
If set to warm temperature, the image looks more red.
(warm image)
Color Settings
Press
into the next menu as below and then use
select item.
or
 Red Gain/Green Gain/Blue Gain/Red Bias/Green Bias/Blue
Bias/Cyan/Magenta/Yellow: Use or to select Red, Green,
Blue, Cyan, Magenta and Yellow Colors.
 Reset: Choose “Yes” to return the factory default settings for
color adjustments.
English
30
to
User Controls
Color Space
Select an appropriate color matrix type from AUTO, RGB or YUV.
Input Source
Use this option to enable / disable input sources. Press
to enter
the sub menu and select which sources you require. Press “Enter”
to finalize the selection. The projector will not search for inputs that
are not selected.
Image AI
Image AI improves the contrast of the picture by optimizing the
brightness of the lamp according to the picture content.
On: The dynamic image performance manager is active in
making sure your greatest pleasure from seeing a movie
dynamically with the most dark details revealed, vivid and
bright image performed all the way.
 Off: The dynamic image performance manager is on standby.
31
English
User Controls
DISPLAY
Format
Use this function to choose your desired aspect ratio.
XGA
 4:3: This format is for 4×3 input sources.
 16:9-I: This format is for 16×9 input sources, like HDTV and
DVD enhanced for Wide screen TV. (576i/p)
 16:9-II: This format is for 16×9 input sources, like HDTV and
DVD enhanced for Wide screen TV. (480i/p)
 Native: This format displays the original image without any
scaling.
 AUTO: Automatically selects the appropriate display format.
When input is 4:3, the image is displayed as 4:3. When input is
16:9 above, the image is displayed as 16:9- I
English
32
Aspect ratio
(source detected)
Resize image
4:3
1024 x 768 center
16:9-I
1024 x 576 center
XGA model
16:9-II
854 x 480 center
Native
No resize image, 1:1 mapping and
centered. This format shows the
original image without scaling.
User Controls
WXGA
 4:3: This format is for 4×3 input sources.
 16:9: This format is for 16×9 input sources, like HDTV and DVD
enhanced for Wide screen TV.
 16:9 or 16:10
depend on “Screen
Type” setting.
 16:10: This format is for 16×10 input sources, like widescreen
laptops.
 LBX: This format is for non-16x9, letterbox source and for users
who use external 16x9 lens to display 2.35:1 aspect ratio using
full resolution.
 Native: This format displays the original image without any
scaling.
 AUTO: Automatically selects the appropriate display format.
16:10 Screen
480i/p
576i/p
4:3
1080i/p
720p
PC
1066 x 800 center
16:10
1280 x 800 center
LBX
1280 x 960 center, then get the central 1280 x 800 image
to display
Native
16:9 Screen
1:1 mapping
centered.
480i/p
576i/p
4:3
1:1 mapping (960 x
540) display
1280 x 800
1280 x 720
center
1:1
mapping
centered.
1080i/p
720p
PC
960 x 720 center
16:9
1280 x 720 center
LBX
1280 x 960 center, then get the central 1280 x 720 image
to display
Native
1:1 mapping
centered.
1:1 mapping (960 x
540) display
1280 x 720
1280 x 720
center
33
1:1
mapping
centered.
English
User Controls
Edge Mask
 Each I/O has
different setting of
“Edge mask”.
 “Edge mask” and
“Zoom” can’t work at
same time.
Edge mask function removes the noise in a video image. Edge
mask the image to remove video encoding noise on the edge of
video source.
Zoom
 Press the to reduce the size of an image.
 Press the to magnify an image on the projection screen.
H Image Shift
Shift the projected image position horizontally.
V Image Shift
Shift the projected image position vertically.
V Keystone
Press the or to adjust image distortion vertically. If the image
looks trapezoidal, this option can help make the image rectangular.
English
34
User Controls
DISPLAY | 3D
3D
 “IR” options may
vary according to
model.
 “3D Sync Invert” is
only available when
3D is enabled and
this mode 3D is for
DLP link glass only.
 Off: Select “Off” to turn 3D settings off for 3D images.
 DLP Link: Select “DLP Link” to use optimized settings for DLP
Link 3D images.
 IR: Select “IR” to use optimized settings for IR-based 3D
images.
3D Sync. Invert
 Press the “On” to invert left and right frame contents.
 Press the “Off” for default frame contents.
 Compatible 3D
source, 3D content
and active shutter
glasses are required
for 3D viewing.
35
English
User Controls
SETUP
Language
Choose the multilingual OSD menu. Press or into the sub
or
key to select your preferred
menu and then use the
language. Press “Enter” to finalize the selection.
 “Screen Type” is for
WXGA only.
Screen Type
Choose the screen type from16:10 or 16:9.
Projection

Front-Desktop
This is the default selection. The image is projected straight on
the screen.
 Rear-Desktop and
Rear-Ceiling are
to be used with a
translucent screen.

Rear-Desktop
When selected, the image will appear reversed.

Front-Ceiling
When selected, the image will turn upside down.
English
36
User Controls

Rear-Ceiling
When selected, the image will appear reversed in upside down
position.
Menu Location
Choose the menu location on the display screen.
Projector ID
ID definition can be set up by menu (range 0~99), and allow user
control an individual projector by RS232. Refer to page 62~66 for
the complete list of RS232 commands.
Mute
 Choose the “On” to turn mute on.
 Choose the “Off” to turn mute off.
37
English
User Controls
SETUP
Volume
 Volume adjustment
can also control MIC
volume.
 Press the
 Press the
to decrease the volume.
to increase the volume.
Audio Input
The default audio settings are on the back panel of the
projector. Use this option to reassign any of the Audio Inputs
(1 or 2) to the current image source. Each Audio input can be
assigned to more than one video source.
 Audio 1: VGA 1 and VGA 2.
 Audio 2: S-Video/Video.
 MIC: (No default video source)
English
38
User Controls
SETUP | Signal
(RGB)
 “Signal” is only
supported in Analog
VGA (RGB) signal.
Automatic
Automatically selects the signal. If you use this function, the
Phase, frequency items are grayed out, and if Signal is not automatic, the phase, frequency items will appear for user to manually
tune and saved in settings after that for next time projector turns
off and on again.
Phase
Synchronize the signal timing of the display with the graphic card.
If the image appears to be unstable or flickers, use this function to
correct it.
Frequency
Change the display data frequency to match the frequency of
your computer’s graphic card. Use this function only if the image
appears to flicker vertically.
H. Position
 Press the
 Press the
to move the image left.
to move the image right.
V. Position
 Press the
 Press the
to move the image down.
to move the image up.
39
English
User Controls
SETUP | Security
Security
 On: Choose “On” to use security verification when the turning
on the projector.
 Off: Choose “Off” to be able to switch on the projector without
password verification.
Security Timer
 Password default
value is “1234” (first
time).
Use this function to set the how long (Month/Day/Hour) the
projector can be used. Once this time has elapsed you will be
requested to enter your password again.
Change Password
 First time:
1. Press “
” to set the password.
2. The password has to be 4 digits.
3. Use number button on the remote to enter your new
password and then press “ ” key to confirm your
password.
 Change Password:
1. Press “
” to input old password.
2. Use number button to enter current password and then
press “ ” to confirm.
3. Enter new password (4 digits in length) using the number
buttons on the remote, then press “ ” to confirm.
4. Enter new password again and press “
English
40
” to confirm.
User Controls
 If the incorrect password is entered 3 times, the projector will
automatically shut down.
 If you have forgotten your password, please contact your local
office for support.
41
English
User Controls
SETUP | Advanced
Logo
Use this function to set the desired startup screen. If changes are
made they will take effect the next time the projector is powered
on.
 Neutral: Logo is not displayed on startup screen.
 User: Use stored picture from “Logo Capture” function.
 For successful logo
capture, please
ensure that the onscreen image does
not exceed the projector’s native resolution. (XGA:1024x768
or WXGA:1280x800).
Logo Capture
Press
to capture an image of the picture currently displayed
on screen.
Closed Captioning
Use this function to set the desired startup screen. If changes are
made they will take effect the next time the projector is powered
on.
 Off: select “off” to turn off the closed captioning feature.
 CC1:CC1 language: American English.
 CC2:CC2 language (depending on the TV channel of the
user):Spanish, French, Portuguese, German, Danish.
English
42
User Controls
SETUP | Network
Network State
Display the network connection status.
DHCP
Use this function to select your desired startup screen. If you
change the setting from one to another, when you exit the OSD
menu, the new setting will take effect on next open.
 On: Assign an IP address to the projector from an external
DHCP server automatically.
 Off: Assign an IP address manually.
IP Address
Select an IP address.
Subnet Mask
Select subnet mask number.
Gateway
Select the default gateway of the network connected to the
projector.
DNS
Select DNS number.
Apply
Press “
” and then choose “Yes” to apply the selection.
43
English
User Controls
Crestron RoomView Control Tool
Crestron RoomView™ provides a central monitoring station for 250+
control systems on a single Ethernet network (more are possible,
the number depends on the combination of IP ID and IP address).
Crestron RoomView monitors each projector, including projector’s
online status, system power, lamp life, network setting and hardware
faults, plus any custom attribute as defined by the Administrator.
The Administrator can add, delete, or edit room information, contact
information and events, which are logged automatically by the
software for all users. (Operation UI as following image)
1. Main Screen
2. Edit Room
 Crestron RoomView function support is dependent
on models.
English
44
User Controls
3. Edit Attribute
4. Edit Event
For more information, please visit
http://www.crestron.com & www.crestron.com/getroomview.
45
English
User Controls
OPTIONS
Source Lock
 On: The projector will only search current input connection.
 Off: The projector will search for other signals if the current
 With dust filter
installed, High
Altitude mode must
be turned on. Dust
filter is Optional and
may not be required
in some regions.
input signal is lost.
High Altitude
When “On” is selected, the fans will spin faster. This feature is
useful in high altitude areas where the air is thin.
Information Hide
 On: Choose “On” to hide the info message.
 Off: Choose “Off” to show the “searching” message.
Keypad Lock
 To turn off the keypad lock, press and
hold “Enter” key on
top of the projector
for 5 seconds.
When the keypad lock function is “On”, the control panel will be
locked however, the projector can be operated by the remote
control. By selecting “Off”, you will be able to reuse the control
panel.
Background Color
Use this feature to display a “Black”, “Red”, “Blue”, “Green” or
“White”, screen when no signal is available.
IR Receiver
 Front Receiver: Choose “On” to start the receiver. Choose “Off”
to close the receiver.
 Top Receiver: Choose “On” to start the receiver. Choose “Off”
to close the receiver.
English
46
User Controls
Reset Dust Filter
Choose “Yes” to show or “No” to hide the warning message when
the changing filter message is displayed.
Reset
Choose “Yes” to return the display parameters on all menus to the
factory default settings.
47
English
User Controls
OPTIONS |
Advanced
Direct Power On
Choose “On” to activate Direct Power mode. The projector will
automatically power on when AC power is supplied, without
pressing the “ ” key on the projector control panel or on the
remote control.
Auto Power Off (min)
Sets the countdown timer interval. The countdown timer will start,
when there is no signal being sent to the projector. The projector
will automatically power off when the countdown has finished (in
minutes).
Sleep Timer (min)
 When Power mode
(Standby) is set
to Eco (<1W), the
VGA output, Audio
pass-through
and RJ45 will be
deactivated when
the projector is in
standby.
English
48
Sets the countdown timer interval. The countdown timer will start,
with or without a signal being sent to the projector. The projector
will automatically power off when the countdown has finished (in
minutes).
Power Mode (Standby)
 Eco.: Choose “Eco.” to save power dissipation further < 1W.
 Active: Choose “Active” to return to normal standby and the
VGA out port will be enabled.
User Controls
OPTIONS |
Lamp Settings
Lamp Hours
Display the projection time.
Lamp Reminder
Choose this function to show or to hide the warning message
when the changing lamp message is displayed.
The message will appear 30 hours before suggested replacement
of lamp.
Brightness Mode
 When ambient temperature is over 35°C
in operating, the
projector will switch
to STD automatically.
 STD: Choose “STD” to dim the projector lamp which will lower
power consumption and extend the lamp life.
 BRIGHT: Choose “BRIGHT” to increase the brightness.
 Image AI: Choose “Image AI” to improve the contrast of the
picture.
Lamp Reset
Reset the lamp hour counter after replacing the lamp.
49
English
Appendices
Troubleshooting
If you experience a problem with your projector,
please refer to the following information. If a
problem persists, please contact your local
reseller or service center.
No image appears on-screen
 Ensure all the cables and power connections are correctly and
securely connected as described in the “Installation” section.
Ensure all the pins of connectors are not bent or broken.

 Check if the projection lamp has been securely installed. Please
refer to the “Replacing the lamp” section.

Make sure you have removed the lens cap and the projector is
switched on.
 Ensure that the “AV mute” feature is not turned on.
Partial, scrolling or incorrectly displayed image
 Press “Re-SYNC” on the remote.
 If you are using a PC:
For Windows 95, 98, 2000, XP, Windows 7:
1. Open the “My Computer” icon, the “Control Panel” folder, and
then double click on the “Display” icon.
2. Select the “Settings” tab.
3. Verify that your display resolution setting is lower than or equal
to UXGA (1600 × 1200).
4. Click on the “Advanced Properties” button.
If the projector is still not projecting the whole image, you will also
need to change the monitor display you are using. Refer to the
following steps.
5. Verify the resolution setting is lower than or equal to UXGA
(1600 × 1200).
6. Select the “Change” button under the “Monitor” tab.
English
50
Appendices
7. Click on “Show all devices”. Next, select “Standard monitor
types” under the SP box; choose the resolution mode you need
under the “Models” box.
8. Verify that the resolution setting of the monitor display is lower
than or equal to UXGA (1600 × 1200).
 If you are using a Notebook:
1. First, follow the steps above to adjust resolution of the
computer.
2. Press the appropriate keys listed below for your notebook
manufacturer to send signal out from notebook to projector.
Example: [Fn]+[F4]
Acer 
Asus 
Dell 
Gateway 
[Fn]+[F5]
[Fn]+[F8]
[Fn]+[F8]
[Fn]+[F4]
IBM/Lenovo 
HP/Compaq 
NEC 
Toshiba 
[Fn]+[F7]
[Fn]+[F4]
[Fn]+[F3]
[Fn]+[F5]
Mac Apple:
System Preference  Display  Arrangement  Mirror
display
 If you experience difficulty changing resolutions or your monitor
freezes, restart all equipment including the projector.
The screen of the Notebook or PowerBook computer is not
displaying your presentation
 If you are using a Notebook PC
Some Notebook PCs may deactivate their own screens when a
second display device is in use. Each has a different way to be
reactivated. Refer to your computer’s manual for detailed
information.
Image is unstable or flickering
 Use “Phase” to correct it. See page 39 for more information.
 Change the monitor color setting on your computer.
Image has vertical flickering bar
 Use “Frequency” to make an adjustment. See page 39 for more

information.
Check and re-configure the display mode of your graphic card to
make it compatible with the projector.
51
English
Appendices
Image is out of focus
 Make sure the lens cap is removed.
 Adjust the Focus Ring on the projector lens.
 Make sure the projection screen is between the required distance.
See page 17.
The image is stretched when displaying 16:9 DVD title
 When you play anamorphic DVD or 16:9 DVD, the projector will
show the best image when the projector display mode is set to
16:9 in the OSD.
 If you play 4:3 format DVD titles, please change the format to 4:3
in the projector OSD.
 If the image is still stretched, you will also need to adjust the
aspect ratio by referring to the following:
 Please setup the display format as 16:9 (wide) aspect ratio type
on your DVD player.
Image is too small or too large
 Move the projector closer to or further from the screen.
 Press “Menu” button on the remote control or projector panel, go
to “DISPLAY  Format” and try the different settings.
Image is reversed
 Select “SETUP  Projection” from the OSD and adjust the
projection direction.
The projector stops responding to all controls
 If possible, turn off the projector, then unplug the power cord and
wait at least 60 seconds before reconnecting power.
 Check that “Keypad Lock” is not activated by trying to control the
projector with the remote control.
English
52
Appendices
Lamp burns out or makes a popping sound
 When the lamp reaches its end of life, it will burn out and may
make a loud popping sound. If this happens, the projector will not
turn on until the lamp module has been replaced. To replace the
lamp, follow the procedures in the “Replacing the Lamp” section on
pages 57-58.
LED lighting message
Message
Standby State
(Input power cord)
Power on (Warming)
Lamp lighting
Steady light 
No light 
POWER/STANDBY LED
Temp-LED
Lamp-LED
(Green/Amber)
(Red)
(Red)
Amber
Flashing
Green
Green
Power off (Cooling)
Flashing
Green
Error (Over Temp.)
Flashing
Amber
Error (Fan fail)
Flashing
Amber
Error (Lamp fail)
Flashing
Amber
Flashing
* POWER/STANDBY LED be ON when OSD appears, be OFF when OSD disappears.
53
English
Appendices
On Screen Messages
 Temperature warning:
 Fan failed:
 Lamp warning:
 Out of display range:
 Filter warning:
If the remote control does not work
 Check the operating angle of the remote control is within ±15°
both horizontally and vertically of one of the IR receivers on the
projector.
 Make sure there are not any obstructions between the remote
control and the projector. Move to within 7 m (±0°) of the projector.
 Make sure the batteries are inserted correctly.
 Replace batteries if they are exhausted.
English
54
Appendices
Replacing the lamp
The projector automatically detects the lamp life. When the
lamp life is nearing the end of use, you will receive a warning
message.
When you see this message, please contact your local reseller
or service center to change the lamp as soon as possible.
Make sure the projector has been cooled down for at least 30
minutes before changing the lamp.
Warning: If ceiling mounted, please use caution when
opening the lamp access panel. It is recommended to wear
safety glasses if changing the bulb when ceiling mounted.
“Caution must be used to prevent any loose parts from falling out of projector.”
Warning: Lamp compartment may be hot! Allow it to cool
down before changing the lamp!
Warning: To reduce the risk of personal injury, do not drop
the lamp module or touch the lamp bulb. The bulb may shatter and cause injury if it is dropped.
55
English
Appendices
 The screws on the
lamp cover and the
lamp cannot be
removed.
1
2
 The projector
cannot be turned
on if the lamp
cover has not been
placed back on the
projector.
3
4
 Do not touch the
glass area of the
lamp. Hand oil can
cause the lamp to
shatter. Use a dry
cloth to clean the
lamp module if it
was accidentally
touched.
Lamp Replacement Procedure:
1.
2.
3.
4.
5.
6.
7.
Switch off the power to the projector by pressing the “ ” button.
Allow the projector to cool down for at least 30 minutes.
Disconnect the power cord.
Unscrew the one screw on the cover. 1
Lift up and remove the cover. 2
Unscrew the three screws on the lamp module. 3
Lift up the lamp handle and remove the lamp module slowly and carefully. 4
To replace the lamp module, reverse the previous steps.
8. Turn on the projector and use “Lamp Reset” after the lamp module is
replaced.
Lamp Reset: (i) Press “Menu”  (ii) Select “OPTIONS”  (iii) Select
“Lamp Settings”  (iv) Select “Lamp Reset”  (v) Select “Yes”.
English
56
Appendices
Replacing and cleaning the dust
filter
We recommend cleaning the dust filter after every 300 hours
of use, clean it more often if the projector is used in a dusty
environment.
 If dust builds up
on the filter is
not cleaned, the
projector will overheat and cause
problems with
the operation and
shorten the life of
the product.
When you see this message, please find following steps for
cleaning procedure:
2
2
1
4
4
3
5
Cleaning the Dust Filter Procedure:
5 to the projector by pressing the “ ” button.
1. Switch off the power
3
2. Disconnect the power cord.
3. Unscrew the one screw on the cable cover. 1
4. Lift up and remove the cable cover. 2
5. Push the latch by the arrow direction. 3
6. Remove the dust filter slowly and carefully. 4
7. Clean or replace the dust filter. 5
To install the dust filter, reverse the previous steps.
8. Turn on the projector and use “Reset Dust Filter” after the dust filter is
replaced.
Filter Reset: (i) Press “Menu”  (ii) Select “OPTIONS”  (iii) Select
“Reset Dust Filter”  (iv) Select “Yes”.
57
English
Appendices
Compatibility Modes
 Computer Compatibility
Mode
 For widescreen
resolution
(WXGA), the
compatibility
support is
dependent on
Notebook/PC
models.
 120Hz input
signals may be
dependent on
graphics cards
support.
 Please note that
using resolutions
other than native
1024 x 768 (XGA
model), 1280
x 800 (WXGA
model) may result
in some loss of
image clarity.
 For WXGA model
only.
English
58
Resolution
V-Sync (Hz)
Analog
Digital
H-Sync (KHz)
Analog
Digital
VGA
640 × 350
70
70
31.50
31.50
VGA
640 × 350
85
85
37.90
37.90
VGA
640 × 400
85
85
37.90
37.90
VGA
640 × 480
60
60
31.50
31.50
VGA
640 × 480
67
67
-
-
VGA
640 × 480
72
72
37.90
37.90
VGA
640 × 480
75
75
37.50
37.50
VGA
720 × 400
70
70
31.50
31.50
VGA
720 × 400
85
85
37.90
37.90
SVGA
800 × 600
56
56
35.20
35.20
SVGA
800 × 600
60
60
37.90
37.90
SVGA
800 × 600
72
72
48.10
48.10
SVGA
800 × 600
75
75
46.90
46.90
SVGA
800 × 600
120
120
-
-
832 × 624
75
75
-
-
XGA
1024 × 768
60
60
48.40
48.40
XGA
1024 × 768
70
70
56.50
56.50
XGA
1024 × 768
75
75
60.00
60.00
XGA
1024 × 768
120
120
-
-
1152 × 870
75
75
-
-
WXGA
1280 × 800
60
60
49.68
49.64
WSXGA+(*)
1680 × 1050
60
60
65.00
65.00
SXGA
1280 × 1024
60
60
63.98
63.98
UXGA
1600 × 1200
60
60
75.00
75.00
HD
1280 × 720
60
60
45.00
45.00
HD
1280 × 720
120
120
-
-
HD
1920 × 1080
30
30
33.80
33.80
Appendices
 Computer Compatibility
Mode
Resolution
V-Sync (Hz)
H-Sync (KHz)
MAC LC 13”
640 × 480
66.66
34.98
MAC II 13”
640 × 480
66.68
35.00
MAC 16”
832 × 624
74.55
49.73
MAC 19”
1024 × 768
75
60.24
MAC
1152 × 870
75.06
68.68
MAC G4
640 × 480
60
31.35
i MAC DV
1024 × 768
75
60.00
i MAC DV
1152 × 870
75
68.49
 Video Compatibility
NTSC
M (3.58MHz), 4.43 MHz
PAL
B, D, G, H, I, M, N
SECAM
B, D, G, K, K1, L
SDTV
480i/p, 576i/p,
HDTV
720p@50Hz/60Hz, 1080i@50Hz/60Hz, 1080p@24Hz/50Hz/60Hz
59
English
Appendices
RS232 Commands and Protocol
Function List
RS232 Pin Assignments
1
2
3
 RS232 shell is
grounded.
English
60
Pin no.
Spec.
(from projector side)
1
TXD
2
RXD
3
GND
Appendices
RS232 Protocol Function List
XX=00-99, projector's ID,
Baud Rate : 9600
XX=00 is for all projectors
Data Bits: 8
Parity: None
RS232 Command Table v1.2
1.Optoma
There isEX665UT/EW675UT/EX565UT
a <CR> after Stop Bits: 1
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------all Rate
ASCII
Baud
: 9600commands.
Note : There is a <CR> after all ASCII commands
Flow Control : None
Data Bits: 8
0D is the HEX code for <CR> in ASCII code
Parity: None
UART16550 FIFO: Disable
2.Stop
0DBits:
is 1the HEX code
Flow
: None
forControl
<CR>
in ASCII
Projector Return (Pass): P
UART16550 FIFO: Disable
code.Return (Pass): P
Projector
Projector Return (Fail): F
Projector Return (Fail): F
XX=01 99, projector's ID, XX=00 is for all projectors
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SEND to projector
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------232 ASCII Code HEX Code
Function
Description
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX00 1
7E 30 30 30 30 20 31 0D
Power ON
~XX00 0
7E 30 30 30 30 20 30 0D
Power OFF
~XX00 1 ~nnnn
7E 30 30 30 30 20 31 20 a 0D Power ON with Password
~nnnn = ~0000 (a=7E 30 30 30 30) - ~9999(a=7E 39 39 39 39)
~XX01 1
7E 30 30 30 31 20 31 0D
Resync
~XX02 1
7E 30 30 30 32 20 31 0D
AV Mute
On
7E 30 30 30 32 20 30 0D
Off
~XX02 0
~XX03 1
7E 30 30 30 33 20 31 0D
Mute
On
~XX03 0
7E 30 30 30 33 20 30 0D
Off
~XX04 1
7E 30 30 30 34 20 31 0D
Freeze
~XX04 0
7E 30 30 30 34 20 30 0D
Unfreeze
~XX05 1
7E 30 30 30 35 20 31 0D
Zoom Plus
~XX06 1
7E 30 30 30 36 20 31 0D
Zoom Minus
~XX07 1
7E 30 30 30 37 20 31 0D
Up (Pan under zoom)
~XX08 1
7E 30 30 30 38 20 31 0D
Down (Pan under zoom)
~XX09 1
7E 30 30 30 39 20 31 0D
Left (Pan under zoom)
~XX10 1
7E 30 30 31 30 20 31 0D
Right (Pan under zoom)
~XX12 1
7E 30 30 31 32 20 31 0D
Direct Source Command
HDMI
~XX12 5
7E 30 30 31 32 20 35 0D
VGA 1
~XX12 6
7E 30 30 31 32 20 36 0D
VGA 2
~XX12 9
7E 30 30 31 32 20 39 0D
S-Video
~XX12 10
7E 30 30 31 32 20 31 30 0D
Video
~XX12 11
7E 30 30 31 32 20 31 31 0D
Flash Drive
~XX12 12
7E 30 30 31 32 20 31 32 0D
Presenter
~XX12 13
7E 30 30 31 32 20 31 33 0D
USB Display
Display Mode
Presentation
~XX20 1
7E 30 30 32 30 20 31 0D
~XX20 2
7E 30 30 32 30 20 32 0D
Bright
~XX20 3
7E 30 30 32 30 20 33 0D
Movie
~XX20 4
7E 30 30 32 30 20 34 0D
sRGB
~XX20 5
7E 30 30 32 30 20 35 0D
User
~XX20 7
7E 30 30 32 30 20 37 0D
Blackboard
~XX20 8
7E 30 30 32 30 20 38 0D
Classroom
~XX20 9
7E 30 30 32 30 20 39 0D
3D
~XX21 n
7E 30 30 32 31 20 a 0D
Brightness
n = 0 (a=30) ~ 100 (a=31 30 30)
~XX22 n
7E 30 30 32 32 20 a 0D
Contrast
n = 0 (a=30) ~ 100 (a=31 30 30)
~XX23 n
7E 30 30 32 33 20 a 0D
Sharpness
n = 0 (a=30) ~ 31 (a=33 31)
~XX24 n
7E 30 30 32 34 20 a 0D
Color
Red Gain
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX25 n
7E 30 30 32 35 20 a 0D
Green Gain
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX26 n
7E 30 30 32 36 20 a 0D
Blue Gain
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX27 n
7E 30 30 32 37 20 a 0D
Red Bias
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX28 n
7E 30 30 32 38 20 a 0D
Green Bias
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX29 n
7E 30 30 32 39 20 a 0D
Blue Bias
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX30 n
7E 30 30 33 30 20 a 0D
Cyan
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX31 n
7E 30 30 33 31 20 a 0D
Yellow
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX32 n
7E 30 30 33 32 20 a 0D
Magenta
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX33 1
7E 30 30 33 33 20 31 0D
Reset
TM
~XX34 n
7E 30 30 33 34 20 a 0D
BrilliantColor
n = 0 (a=30) ~ 10 (a=31 30)
~XX35 1
7E 30 30 33 35 20 31 0D
Degamma
Film
~XX35 2
7E 30 30 33 35 20 32 0D
Video
~XX35 3
7E 30 30 33 35 20 33 0D
Graphics
~XX35 4
7E 30 30 33 35 20 34 0D
PC
~XX36 1
7E 30 30 33 36 20 31 0D
Color Temp.
Warm
~XX36 2
7E 30 30 33 36 20 32 0D
Medium
~XX36 3
7E 30 30 33 36 20 33 0D
Cold
~XX37 1
7E 30 30 33 37 20 31 0D
Color Space
Auto
* HDMI w/o Color Space item
~XX37 2
7E 30 30 33 37 20 32 0D
RGB
~XX37 3
7E 30 30 33 37 20 33 0D
YUV
~XX39 5
7E 30 30 33 39 20 35 0D
Input Source
VGA1
~XX39 6
7E 30 30 33 39 20 35 0D
VGA2
~XX39 9
7E 30 30 33 39 20 39 0D
S-Video
~XX39 10
7E 30 30 33 39 20 31 30 0D
Video
~XX39 1
7E 30 30 33 39 20 31 0D
HDMI
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
61
English
Appendices
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX39 11
7E 30 30 33 39 20 31 31 0D
Flash Drive
~XX39 12
7E 30 30 33 39 20 31 32 0D
Presenter(LAN+Wireless)
~XX39 13
7E 30 30 33 39 20 31 33 0D
USB Display
~XX44 n
7E 30 30 34 34 20 a 0D
Tint
n = 0 (a=30) ~ 100 (a=31 30 30)
~XX45 n
7E 30 30 34 35 20 a 0D
Color (Saturation)
n = 0 (a=30) ~ 100 (a=31 30 30)
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------(EW675UT/UTi only)
~XX60 1
7E 30 30 36 30 20 31 0D
Format
4:3
~XX60 2
7E 30 30 36 30 20 32 0D
16:9/16:10
~XX60 5
7E 30 30 36 30 20 35 0D
LBX
~XX60 6
7E 30 30 36 30 20 36 0D
Native
~XX60 7
7E 30 30 36 30 20 37 0D
AUTO
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------(EX665UT/UTi only)
~XX60 1
7E 30 30 36 30 20 31 0D
Format
4:3
~XX60 2
7E 30 30 36 30 20 32 0D
16:9-I
~XX60 3
7E 30 30 36 30 20 35 0D
16:9-II
~XX60 6
7E 30 30 36 30 20 36 0D
Native
~XX60 7
7E 30 30 36 30 20 37 0D
AUTO
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX61 n
7E 30 30 36 31 20 a 0D
Edge Mask
n = 0 (a=30) ~ 10(a=31 30)
~XX62 n
7E 30 30 36 32 20 a 0D
Zoom
n = -5 (a=2D 35) ~ 25 (a=32 35)
~XX63 n
7E 30 30 36 33 20 a 0D
H Image Shift
n = -50 (a=2D 35 30) ~ +50 (a=35 30)
~XX64 n
7E 30 30 36 34 20 a 0D
V Image Shift
n = -50 (a=2D 35 30) ~ +50 (a=35 30)
~XX66 n
7E 30 30 36 36 20 a 0D
V Keystone
n = -40 (a=2D 34 30) ~ 40 (a=34 30)
~XX230 1
7E 30 30 32 33 30 20 31 0D
3D Mode
On
~XX230 0
7E 30 30 32 33 30 20 30 0D
3D Mode
Off
~XX231 1
7E 30 30 32 33 31 20 31 0D
3D Sync Invert
On
~XX231 0
7E 30 30 32 33 31 20 30 0D
3D Sync Invert
Off
~XX70 1
7E 30 30 37 30 20 31 0D
Language
English
~XX70 2
7E 30 30 37 30 20 32 0D
German
~XX70 3
7E 30 30 37 30 20 33 0D
French
~XX70 4
7E 30 30 37 30 20 34 0D
Italian
~XX70 5
7E 30 30 37 30 20 35 0D
Spanish
~XX70 6
7E 30 30 37 30 20 36 0D
Portuguese
~XX70 7
7E 30 30 37 30 20 37 0D
Polish
~XX70 8
7E 30 30 37 30 20 38 0D
Dutch
~XX70 9
7E 30 30 37 30 20 39 0D
Swedish
~XX70 10
7E 30 30 37 30 20 31 30 0D
Norwegian/Danish
~XX70 11
7E 30 30 37 30 20 31 31 0D
Finnish
~XX70 12
7E 30 30 37 30 20 31 32 0D
Greek
~XX70 13
7E 30 30 37 30 20 31 33 0D
Traditional Chinese
~XX70 14
7E 30 30 37 30 20 31 34 0D
Simplified Chinese
~XX70 15
7E 30 30 37 30 20 31 35 0D
Japanese
~XX70 16
7E 30 30 37 30 20 31 36 0D
Korean
~XX70 17
7E 30 30 37 30 20 31 37 0D
Russian
~XX70 18
7E 30 30 37 30 20 31 38 0D
Hungarian
~XX70 19
7E 30 30 37 30 20 31 39 0D
Czechoslovak
~XX70 20
7E 30 30 37 30 20 32 30 0D
Arabic
~XX70 21
7E 30 30 37 30 20 32 31 0D
Thai
~XX70 22
7E 30 30 37 30 20 32 32 0D
Turkish
~XX70 23
7E 30 30 37 30 20 32 33 0D
Farsi
~XX70 25
7E 30 30 37 30 20 32 35 0D
Vietnamese
~XX70 26
7E 30 30 37 30 20 32 36 0D
Romanian
~XX70 27
7E 30 30 37 30 20 32 37 0D
Indonesia
~XX71 1
7E 30 30 37 31 20 31 0D
Projection
Front-Desktop
~XX71 2
7E 30 30 37 31 20 32 0D
Rear-Desktop
~XX71 3
7E 30 30 37 31 20 33 0D
Front-Ceiling
~XX71 4
7E 30 30 37 31 20 34 0D
Rear-Ceiling
~XX72 1
7E 30 30 37 32 20 31 0D
Menu Location
Top Left
~XX72 2
7E 30 30 37 32 20 32 0D
Top Right
~XX72 3
7E 30 30 37 32 20 33 0D
Centre
~XX72 4
7E 30 30 37 32 20 34 0D
Bottom Left
~XX72 5
7E 30 30 37 32 20 35 0D
Bottom Right
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------(EW675UT/UTi only)
~XX90 1
7E 30 30 39 31 20 31 0D
Screen Type
16:10
~XX90 0
7E 30 30 39 31 20 30 0D
16:9
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX91 1
7E 30 30 39 31 20 31 0D
Signal
Automatic
On
~XX91 0
7E 30 30 39 31 20 30 0D
Automatic
Off
~XX73 n
7E 30 30 37 33 20 a 0D
Frequency
n = -5 (a=2D 35) ~ 5 (a=35) By signal
~XX74 n
7E 30 30 37 34 20 a 0D
Phase
n = 0 (a=30) ~ 31 (a=33 31) By signal
~XX75 n
7E 30 30 37 35 20 a 0D
H. Position
n = -5 (a=2D 35) ~ 5 (a=35) By timing
~XX76 n
7E 30 30 37 36 20 a 0D
V. Position
n = -5 (a=2D 35) ~ 5 (a=35) By timing
~XX77 n
7E 30 30 37 37 20 aabbcc 0D Security
Security Timer
Month/Day/Hour
n = mm/dd/hh
mm = 00 (aa=30 30) ~ 12 (aa=31 32)
dd = 00 (bb=30 30) ~ 30 (bb=33 30)
hh = 00 (cc=30 30) ~ 24 (cc=32 34)
~XX78 1
7E 30 30 37 38 20 31 0D
Security
On
~XX78 0
7E 30 30 37 38 20 32 0D
Off (0/2 for backward compatible)
~XX79 n
7E 30 30 37 39 20 a 0D
Projector ID
n = 00 (a=30 30) ~ 99 (a=39 39)
~XX80 1
7E 30 30 38 30 20 31 0D
Mute
On
~XX80 0
7E 30 30 38 30 20 30 0D
Off
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
62
English
V1.2 2011-03-23
Appendices
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX81 n
7E 30 30 38 31 20 a 0D
Volume
n = 0 (a=30) ~ 20 (a=32 30)
~XX82 1
7E 30 30 38 32 20 31 0D
Logo
Optoma
~XX82 2
7E 30 30 38 32 20 32 0D
User
~XX83 1
7E 30 30 38 33 20 31 0D
Logo Capture
~XX88 0
7E 30 30 38 38 20 30 0D
Closed Captioning
Off
~XX88 1
7E 30 30 38 38 20 31 0D
cc1
cc2
~XX88 2
7E 30 30 38 38 20 32 0D
~XX100 1
7E 30 30 31 30 30 20 31 0D
Source Lock
On
~XX100 0
7E 30 30 31 30 30 20 30 0D
Off
~XX100 3
7E 30 30 31 30 30 20 33 0D
Next Source
~XX101 1
7E 30 30 31 30 31 20 31 0D
High Altitude
On
~XX101 0
7E 30 30 31 30 31 20 30 0D
Off
~XX102 1
7E 30 30 31 30 32 20 31 0D
Information Hide
On
~XX102 0
7E 30 30 31 30 32 20 30 0D
Off
~XX103 1
7E 30 30 31 30 33 20 31 0D
Keypad Lock
On
~XX103 0
7E 30 30 31 30 33 20 30 0D
Off
~XX104 1
7E 30 30 31 30 34 20 31 0D
Background Color
Blue
~XX104 2
7E 30 30 31 30 34 20 32 0D
Black
~XX104 3
7E 30 30 31 30 34 20 33 0D
Red
~XX104 4
7E 30 30 31 30 34 20 34 0D
Green
~XX104 5
7E 30 30 31 30 34 20 35 0D
White
7E 30 30 31 30 35 20 31 0D
Advanced
Direct Power On
On
~XX105 1
~XX105 0
7E 30 30 31 30 35 20 30 0D
Off
~XX106 n
7E 30 30 31 30 36 20 a 0D
Auto Power Off (min) n = 0 (a=30) ~ 180 (a=31 38 30) , step=1
~XX107 n
7E 30 30 31 30 37 20 a 0D
Sleep Timer (min)
n = 0 (a=3 0) ~ 995 (a=39 39 35) , step=5
~XX114 1
7E 30 30 31 31 34 20 31 0D
Power Mode(Standby) Eco.(<=1W)
~XX114 0
7E 30 30 31 31 34 20 30 0D
Active
~XX109 1
7E 30 30 31 30 39 20 31 0D
Lamp Reminder
On
~XX109 0
7E 30 30 31 30 39 20 30 0D
Off
~XX110 0
7E 30 30 31 31 30 20 31 0D
Brightness Mode
STD
~XX110 1
7E 30 30 31 31 30 20 30 0D
Bright
~XX110 2
7E 30 30 31 31 30 20 30 0D
ImageAI
~XX111 1
7E 30 30 31 31 31 20 31 0D
Lamp Reset
Yes
No
~XX111 0
7E 30 30 31 31 31 20 30 0D
~XX112 1
7E 30 30 31 31 32 20 31 0D
Reset
Yes
~XX120 0
7E 30 30 31 32 30 20 30 0D
Point Blank
Interactive
Off
~XX120 1
7E 30 30 31 32 30 20 31 0D
On
~XX121 0
7E 30 30 31 32 31 20 30 0D
Dual Pen
Off
~XX121 0
7E 30 30 31 32 31 20 31 0D
On
~XX122 0
7E 30 30 31 32 32 20 30 0D
Pointer Motion
Draw
~XX122 1
7E 30 30 31 32 32 20 31 0D
Normal
~XX122 2
7E 30 30 31 32 32 20 32 0D
Stable
~XX123 0
7E 30 30 31 32 33 20 30 0D
Click Speed
Fast
~XX123 1
7E 30 30 31 32 33 20 31 0D
Medium
~XX123 2
7E 30 30 31 32 33 20 32 0D
Slow
~XX124 0
7E 30 30 31 32 34 20 30 0D
Set Function
Pointer Motion
~XX124 1
7E 30 30 31 32 34 20 31 0D
PowerPoint Annotation
~XX124 2
7E 30 30 31 32 34 20 32 0D
Switch Window
~XX124 3
7E 30 30 31 32 34 20 33 0D
Esc
~XX124 4
7E 30 30 31 32 34 20 34 0D
Show Desktop
~XX124 5
7E 30 30 31 32 34 20 35 0D
Open Windows Explorer
~XX124 6
7E 30 30 31 32 34 20 36 0D
Middle Click
~XX124 7
7E 30 30 31 32 34 20 37 0D
Double Click
~XX124 8
7E 30 30 31 32 34 20 38 0D
Disable
~XX125 n
7E 30 30 31 32 35 20 a 0D
Channel
n=0 (a:0x30) , Auto
n=1~30 (a:0x31 ~ 0x33 0x30) , Channel number
~XX126 1
7E 30 30 31 32 36 20 31 0D
Information
~XX127 1
7E 30 30 31 32 37 20 31 0D
Reset Dust Filter
~XX128 0
7E 30 30 31 32 38 20 30 0D
IR Receiver
Top Receiver
Off
~XX128 1
7E 30 30 31 32 38 20 31 0D
On
~XX129 0
7E 30 30 31 32 39 20 30 0D
Front Receiver
Off
~XX129 1
7E 30 30 31 32 39 20 31 0D
On
~XX130 0
7E 30 30 31 33 30 20 30 0D
Audio Input
Default
~XX130 1
7E 30 30 31 33 31 20 31 0D
AUDIO1
~XX130 2
7E 30 30 31 33 32 20 32 0D
AUDIO2
~XX210 n
7E 30 30 32 30 30 20 n 0D
Display message on the OSD
n: 1-30 characters
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SEND as Remote Control Key
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX140 1
7E 30 30 31 34 30 20 31 0D
Power
~XX140 3
7E 30 30 31 34 30 20 33 0D
Mouse Up
~XX140 4
7E 30 30 31 34 30 20 34 0D
Mouse Left
~XX140 5
7E 30 30 31 34 30 20 35 0D
Mouse Enter
~XX140 6
7E 30 30 31 34 30 20 36 0D
Mouse Right
Mouse Down
~XX140 7
7E 30 30 31 34 30 20 37 0D
~XX140 8
7E 30 30 31 34 30 20 38 0D
Mouse Left Click
~XX140 9
7E 30 30 31 34 30 20 39 0D
Mouse Right Click
~XX140 10
7E 30 30 31 34 30 20 31 30 0D
Up/Page +
~XX140 11
7E 30 30 31 34 30 20 31 31 0D
Left/Source
~XX140 12
7E 30 30 31 34 30 20 31 32 0D
Enter (for projection MENU)
~XX140 13
7E 30 30 31 34 30 20 31 33 0D
Right/Re-SYNC
~XX140 14
7E 30 30 31 34 30 20 31 34 0D
Down/Page ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
V1.2 2011-03-23
63
English
Appendices
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX140 15
7E 30 30 31 34 30 20 31 35 0D
Keystone +
~XX140 16
7E 30 30 31 34 30 20 31 36 0D
Keystone ~XX140 17
7E 30 30 31 34 30 20 31 37 0D
Volume ~XX140 18
7E 30 30 31 34 30 20 31 38 0D
Volume +
~XX140 19
7E 30 30 31 34 30 20 31 39 0D
Brightness (1)
Menu (2)
~XX140 20
7E 30 30 31 34 30 20 32 30 0D
~XX140 21
7E 30 30 31 34 30 20 32 31 0D
3D(3)
~XX140 22
7E 30 30 31 34 30 20 32 32 0D
HDMI (4)
~XX140 23
7E 30 30 31 34 30 20 32 33 0D
Freeze (5)
~XX140 24
7E 30 30 31 34 30 20 32 34 0D
AV Mute (6)
~XX140 25
7E 30 30 31 34 30 20 32 35 0D
S-Video (7)
~XX140 26
7E 30 30 31 34 30 20 32 36 0D
VGA (8)
~XX140 27
7E 30 30 31 34 30 20 32 37 0D
Video (9)
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SEND from projector automatically
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------232 ASCII Code HEX Code
Function
Projector Return
Description
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------System status
INFOn
n : 0/1/2/3/4/6/7/8 = Standby/Warming/Cooling/Out of Range/
Lamp fail/Fan Lock/Over Temperature/Lamp Hours Running Out
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------READ from projector
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------232 ASCII Code HEX Code
Function
Projector Return
Description
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX121 1
7E 30 30 31 32 31 20 31 0D
Input Source
OKn
n : 0/1/2/3/4/5/6/7/8 = None / VGA1 / VGA2 / S-Video /
Video / HDMI / Flash Drive/Presenter/USB Display
~XX122 1
7E 30 30 31 32 32 20 31 0D
Sofware Version
OKdddd
dddd: FW version
~XX123 1
7E 30 30 31 32 33 20 31 0D
Display Mode
OKn
n : 0/1/2/3/4/5/6/7/8 = None/Presentation/Bright/Movie/sRGB/
User/Blackboard/Classroom/3D
~XX124 1
7E 30 30 31 32 34 20 31 0D
Power State
OKn
n : 0/1 = Off/On
~XX125 1
7E 30 30 31 32 35 20 31 0D
Brightness
OKn
~XX126 1
7E 30 30 31 32 36 20 31 0D
Contrast
OKn
~XX127 1
7E 30 30 31 32 37 20 31 0D
Aspect Ratio
OKn
(EW675UT/UTi) n: 0/1/2/3/4 = 4:3 / 16:9 or 16:10 * / LBX /
Native / AUTO
(EX665UT/UTi) n: 0/1/2/3/4 = 4:3 / 16:9-I / 16:9-II / Native /
AUTO
* 16:9 or 16:10 depend on Screen Type setting
~XX128 1
7E 30 30 31 32 38 20 31 0D
Color Temperature
OKn
n : 0/1/2 = Warm/Medium/Cold
~XX129 1
7E 30 30 31 32 39 20 31 0D
Projection Mode
OKn
n : 0/1/2/3 = Front-Desktop/Rear-Desktop/Front-Ceiling/
Rear-Ceiling
~XX150 1
7E 30 30 31 35 30 20 31 0D
Information
OKabbbbccdddde
a : 0/1 = Off/On
bbbb: LampHour
cc: source 00/01/02/03/04/05/06/07/08= None/VGA1/
VGA2/S-Video/Video/HDMI/Flash Drive/
Presenter/USB Display
dddd: FW version
e : Display mode 0/1/2/3/4/5/6/7/8
None/Presentation/Bright/Movie/sRGB/User/
Blackboard/Classroom/3D
~XX151 1
7E 30 30 31 35 31 20 31 0D
Model name
OKn
n: 17/18/19=EX665UT(UTi) / EW675UT(UTi) / EX565UT
~XX108 1
7E 30 30 31 30 38 20 31 0D
Lamp Hours
OKbbbb
bbbb: LampHour
OKbbbbb
bbbbb: (5 digits) Total Lamp Hours
~XX108 2
7E 30 30 31 30 38 20 31 0D
Cumulative Lamp Hours
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
64
English
V1.2 2011-03-23
Appendices
Wall Mount Installation
1. To prevent damage to your projector, please use the
Triumph Board ceiling mount.
2. If you wish to use a third party ceiling mount kit, please
ensure the screws used to attach a mount to the projector
meet the following specifications:
407
146
109.4
Warning:
1. If you buy a ceiling
mount from another
company, please
be sure to use the
correct screw size.
Screw size will vary
depending on the
thickness of the
mounting plate.
2. Be sure to keep
at least 10 cm gap
between the ceiling
and the bottom of the
projector.
3. Avoid installing the
projector near a heat
source.
426.2
151.3
112.5
 Please note that
damage resulting
from incorrect
installation will void
the warranty.
 Screw type: M4*4
 Maximum screw length: 11mm
 Minimum screw length: 8mm
43
Lens
163
Unit: mm
65
English
Appendices
Regulation & Safety Notices
This appendix lists the general notices of your projector.
FCC notice
This device has been tested and found to comply with the
limits for a Class B digital device pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This device generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this device does cause
harmful interference to radio or television reception, which can
be determined by turning the device off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the device and receiver.
• Connect the device into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/television
technician for help.
Notice: Shielded cables
All connections to other computing devices must be
made using shielded cables to maintain compliance with
FCC regulations.
Caution
Changes or modifications not expressly approved by the
manufacturer could void the user’s authority, which is
granted by the Federal Communications Commission, to
operate this projector.
English
66
Appendices
Operation conditions
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
1. This device may not cause harmful interference and
2. This device must accept any interference received,
including interference that may cause undesired
operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian
ICES-003.
Remarque à l’intention des utilisateurs
canadiens
Cet appareil numerique de la classe B est conforme a la
norme NMB-003 du Canada.
Declaration of Conformity for EU
countries
• EMC Directive 2004/108/EC (including amendments)
• Low Voltage Directive 2006/95/EC
• R & TTE Directive 1999/5/EC (if product has RF function)
Disposal instructions
Do not throw this electronic device into the
trash when discarding. To minimize pollution
and ensure utmost protection of the global
environment, please recycle it.
67
English
Repair Service
Repair Service and Contacts
Please contact your local supplier for the warranty and technical
service or find all warranty conditions and service partners on
our website www.triumphboard.com .
For any questions please email us to info@triumphboard.com
TRIUMPH BOARD a.s.
Neklanova 122/15
128 00 Praha 2
Czech Republic
EU
Phone: +420 224910221
Fax: +420 224910218
E-mail: info@triumphboard.com
www.triumphboard.com
Notices
Every effort has been made to ensure all information contained in this
user guide is correct, but the accuracy or completeness is not guaranteed.
Before using this product, you must evaluate it and determine if it is suitable
for your intended application. You assume all risks and liability associated
with such use. Any statements related to this product which is not contained
in this manual or any contrary statements contained on your purchase order
shall have no force of effect unless expressly agreed upon, in writing, by
this company.
Without this company permission, reproduction or reprinting this user guide
or any part is prohibited.
The contents of this user guide are subject to change without prior notice.
PLEASE see our website www.triumphboard.com for updates
and fresh product information in the product and support
sections.
68
English
Download PDF
Similar pages