Note: TEW-310APBX functions just like TEW-310APB and
the configuration procedures are the same as the TEW310APB. The only difference between the two models is the
TEW-310APBX comes with 2 detachable antennas. Below is
the antenna installation instruction.
Replacing the Antenna with High Gain Antenna
You can also replace one of the antennas with a higher gain
TRENDnet antenna (4dBi Indoor Omni Directional, 6dBi Indoor
Patch Directional, or 14dBi Outdoor Directional). At default,
both antennas are transmitting/receiving data. When installing
the high gain antenna, you can choose to install it on either the
left or right antenna position. After that, go to the Access
Point's configuration page, select "Advanced Settings", and at
the bottom of the page, select the desired antenna position.
TEW-310APB/TEW-310APBX
Wireless Access Point + Bridge
Quick User Installation Guide
This product can be set up using any current web browser, i.e., Internet
Explorer 5.x or above, Netscape Navigator 4.x or above.
Before You Begin
You can configure TEW-310APB with Web Browser or the included Windows Utility
(22M AP Utility).
It’s best to connect the TEW-310APB to an Ethernet Hub or Ethernet Switch and
then connect a computer (with an Ethernet adapter) to this Hub/Switch and perform
the configuration from the computer. The default IP address for the TEW-310APB is
192.168.1.1 with Subnet Mask 255.255.255.0. The DHCP Service is enabled and the
unit will distribute IP addresses to computers in the network that request IP addresses.
See the User’s Guide on the CD-ROM for detail information in setting IP address for
your network adapter.
If you already have a DHCP Server in the network (i.e., an Internet Router), please do
not connect TEW-310APB to the network, you must disable the TEW-310APB’s DHCP
service, enable its DHCP Client to request IP address, and the you can connect the TEW310APB to the network. To find out TEW-310APB’s IP address, you can simply run the
Windows 22M AP Utility software that is in the included CD-ROM.
If you have TEW-301PC or TEW-303PI wireless adapter installed in a computer, with the
default settings (ESSID: default), you will be able to connect and configure the TEW310APB (Note: you will still need to configure the TEW-301PC or TEW-303PI TCP/IP
settings to obtain IP address automatically).
Package Contents
• TEW-310APB/TEW-310APBX Wireless Access Point
• CD-ROM (containing Manual and Warranty)
Note: TEW-310APBX
• Quick Installation Guide
comes with two
• Ethernet (CAT5 UTP/Straight Through) Cable
detachable antennas.
• 5V DC, 2A Power Adapter
If any of the above items are missing, please contact your reseller.
Warning!
Using a power supply
with a different voltage rating will damage and
void the warranty for this product.
1. Connecting The TEW-310APB Wireless
Access Point To Your Network
a. First, connect the power adapter to the receptor at the back of the
TEW-310APB and then plug the other end of the power adapter to an
electrical outlet. The Power LED will light, indicating the unit is
receiving power.
b. Using the Straight-Through Ethernet cable (included), insert one end
of the cable to the Ethernet port on the back of the TEW-310APB
and the other end of the cable to Ethernet Hub or Switch. The Link
LED on the TEW-310APB will illuminate to indicate a proper Ethernet
connection. Also, connect the computer that you will be using to
configure the TEW-310APB to the Hub or Switch; the Hub/Switch’s
LEDs will display Link for the TEW-310APB and the computer’s
connections. (Note: you can also connect the computer’s Ethernet
card directly to the TEW-310APB’s Ethernet port using a crossover
UTP RJ-45 cable (not included)).
c.
Computers with 802.11b wireless adapters can connect to the TEW310APB. Simply set the wireless adapter to Infrastructure mode with
default as its ESSID and WEP (encryption) disabled. The TEW301PC Wireless CardBus Adapter and the TEW-303PI Wireless
PCI Adapter will connect, out of the box, with the TEW-310APB,
using their default wireless settings.
Diversity Antenna
Receptor for
Power Adapter
Reset button: Press this
button to reset all
configurations back to
factory default settings.
Ethernet Port (RJ-45 port):
Supports 10/100Mbps. Use
Ethernet cable to connect
this port to another Ethernet
port on the Ethernet Hub,
Switch, or Internet Router.
When you have completed the steps in the previous page, your
connected network should look similar to one of these:
* Configure with Ethernet networked
Computer via 5-Port Switch
** Configure with Computer with
Wireless Network Adapter
*** Configure with Ethernet networked
Computer via Crossover UTP RJ-45 cable
Application Diagram: Internet sharing
using wireless Access Point
2. Configure Network Card’s IP Address
Please follow the instructions below to
configure the computer’s network card’s
TCP/IP settings.
For Microsoft Windows XP: From the
Desktop, right click on My Network Places >
select Properties > double-click on the
Network Connection.
Click Internet Protocol (TCP/IP)
Click Properties
Obtain IP address Automatically
When you have a DHCP server (i.e. Router with
DHCP Server enabled) on the network
Select Obtain an IP address
automatically
Select Obtain DNS server
address automatically
Click OK
For Windows 2000:
From the Desktop, right click on My network
places and select Properties > Double-click on
the Local Area Connection associated
with the wireless adapter > select Properties.
Click Internet Protocol (TCP/IP)
Click Properties
Obtain IP address Automatically
When you have a DHCP server (i.e. Router with
DHCP Server enabled) on the network
Select Obtain an IP address
automatically
Select Obtain DNS server
address automatically
Click OK
Follow Windows prompt and restart the
computer.
For Windows Me and 98:
From the Desktop, right click on
Network Neighborhood > select Properties.
Click TCP/IP ? Network Adapter
Click Properties
Obtain IP address Automatically
When you have a DHCP server (i.e. Router with
DHCP Server enabled) on the network
Select Obtain an IP address
automatically (if the Wireless
Router or Access Point has DHCP
server enabled)
Click to check Detect connection to
network media
Click OK
Follow Windows prompt to restart the
computer.
For Macintosh OS:
After you have completed the hardware
installation, power on all the equipments,
and then power on your Macintosh.
In the Finder, go to the Apple menu in
the upper left hand corner of the screen
and select System Preferences.
Select Network
Click on TCP/IP tab
At the Configure drop-down menu,
select Using DHCP
Click on Save
Open the web browser and go to address
http://192.168.1.1 (default setting) to
enter the configuration page.
3. Configure TEW-310APB Using
Web Browser
Open your web browser, at the Address
box, type in http://192.168.1.1 and press
Enter or click on Go.
At Enter Network Password windows,
in User Name box, type in admin, in
Password box, also type in admin and
click Ok.
You will see the Status screen with
menu bar.
The Status screen displays wired LAN
(Local Area Network) and Wireless
network configurations.
Click on Basic Setting
AP Name: Enter a name for
this particular Access Point.
Channel: Displays the channel number
SSID: The Service Set
WEP Key: There are three levels of
Identifier is the name assigned
to the wireless network. The
factory SSID setting is set to
default. Make changes here to
match the SSID on existing
other wireless station.
the Access Point is using.
wireless encryption - 64-bit, 128-bit,
and 256-bit. By default the
encryption is disabled. You can
change the encryption settings for
more secure wireless communication.
Mode: Select HEX for entering HEX
numbers 0 ~ 9 and A ~ F. Or select ASCII for
entering any ACSII characters. The amount of
characters that you can enter is depends on
the level of WEP Key. The higher the WEP
key level, the more characters you need to
enter for the key. For 64-bit key, you need to
enter 10 HEX or 5 ASCII characters. 128-bit
requires 26 HEX or 13 ASCII characters. 256bit WEB key needs 58 HEX or 29 ASCII
characters.
Click Apply to save the configurations.
4. Configuration Completed!
For additional settings or information, refer to the IP Setting, Advance Setting,
Security, and Tools tabs on the Menu Bar; or to the User’s Guide located on the CDROM.
5. Install TEW-310APB 22M AP Windows
Configuration Utility
Install the Utility on a computer running Windows 98 or above by inserting the CDROM to the CD-ROM drive. The CD-ROM will Autorun and you will see the menu
screen.
Note: If the CD Autorun function on your computer does not automatically start, please
double click on My Computer on the desktop, right click on the
CD Drive, select Explore, double-click on 22M.EXE
Click on the model name
Click on Install
Note: If the utility has been installed on this
computer, the Install tab will not be active.
Click on Next
Click on Next
Click on Finish
6. Configure TEW-310APB Using 22M AP
Utility
Double click on the 22M AP Utility shortcut icon on the desktop.
Click on AP Settings to set the
unit’s ESSID and Channel
Click IP Settings to change the
IP address
Click WEP Settings to setup the
encryption
Click Apply at the bottom of
each setup screen to save the
settings.
Checking the Wireless Connection
For Windows XP and 2000, go
to Start > Run > type cmd and
click OK. A window similar to
the one on the right will appear.
Type ping xxx.xxx.xxx.xxx and
hit Enter key (where xxx… is
the IP address of the wireless
router or Access Point). A good
wireless connection will show
Reply from the wireless router
or access point.
To display the network adapter’s IP information, type in ipconfig/all and hit Enter.
For Windows Me and 98SE, go
to Start > Run > type
command and click OK. A
window similar to this will
appear. Type ping
xxx.xxx.xxx.xxx and hit Enter
key (where xxx… is the IP
address of the wireless router or
Access Point). A good wireless
connection will show the reply
from the wireless router or
access point.
Troubleshooting
Q1: I cannot connect to the access point or wireless router.
A: Make sure that the SSID on the Wireless Adapter is exactly the same as the SSID
on the Access Point or Wireless Router.
Q2: The TEW-310APB Power and Link lights are not on.
A: Check to see if the Power adapter is connected to the power receptor on the back
of the unit and if the power source is receiving power. Also, check the network
cable connecting to the Hub/Switch and make sure it is working properly.
Q3: I am unable to access the configuration page using web browser.
A1: Check that the LED on the unit, make sure they lights up according to the
instructions.
A2: Check that the TCP/IP settings of your network adapter and make sure it is set at
“obtain IP automatically”.
A3: If you have a computer running Windows in the network, install and run the 22M
AP Utility and configure the unit using the utility.
A4: Find the reset button on the back of the unit, press and hold it for 5 seconds,
release the button (the device will be restore its default settings), and reconfigure the
unit according to this instructions.
Q4: I forgot my Encryption key.
A: Find the reset button on the back of the unit, press and hold it for 5 seconds,
release the button (the device will be restore its default settings), and reconfigure the
unit according to this instructions.
Technical Support
You can find the most recent software and user documentation on the TRENDware
website. TRENDware provides free technical support for all customers for the
duration of the warranty period on this product.
TRENDware Technical Support
Tel: +1-310-891-1100
Fax: +1-310-8911111
E-mail: support@trendware.com
www.trendware.com