PBS Pro Administrator Guide - UBC Physics: Numerical Relativity

Release 5.2
Administrator Guide
Portable Batch SystemTM Administrator Guide
PBS-3BA01, Release: PBS ProTM 5.2, Updated: March 27, 2002
Edited by: James Patton Jones
Contributing authors include: Albeaus Bayucan, Robert L. Henderson, James
Patton Jones, Casimir Lesiak, Bhroam Mann, Bill Nitzberg, Tom Proett.
Copyright (c) 2000-2002 Veridian Systems, Inc.
All rights reserved under International and Pan-American Copyright Conventions. All
rights reserved. Reproduction of this work in whole or in part without prior written permission of Veridian Systems is prohibited.
Veridian Systems is an operating company of the Veridian Corporation. For more information about Veridian, visit the corporate website at: www.veridian.com.
Trademarks: OpenPBS, “PBS Pro”, “Portable Batch System” and the PBS Juggler logo
are trademarks of Veridian Systems, Inc. All other trademarks are the property of their
respective owners.
For more information, redistribution, licensing, or additional copies of this
publication, contact:
Veridian Systems
PBS Products Dept.
2672 Bayshore Parkway, Suite 810
Mountain View, CA 94043
Phone: +1 (650) 967-4675
FAX: +1 (650) 967-3080
URL: www.pbspro.com
Email: sales@pbspro.com
For online purchases, visit: store.pbspro.com
PBS Pro 5.2 vi
Administrator Guide
Table of Contents
Acknowledgements ........................................................... ix
Preface ............................................................................... xi
1 Introduction................................................................. 1
Book Organization....................................................1
What is PBS Pro? .....................................................2
About Veridian .........................................................4
2 Concepts and Terms ................................................... 5
PBS Components......................................................6
Defining PBS Terms.................................................8
3 Pre-Installation Planning ......................................... 13
New Features in PBS Pro 5.2 .................................13
Server - MOM Protocol Change.............................15
Changes to Time-shared and Cluster Nodes ..........15
Interfacing with Globus..........................................16
Single Execution System........................................17
Multiple Execution Systems...................................18
4 Installation ................................................................. 19
Overview ................................................................19
Media Setup............................................................20
Default Install Options ...........................................21
Installation on UNIX/Linux Systems .....................21
Installation on Windows 2000 Systems .................24
Installing the PBS License......................................25
Using Floating Licenses .........................................26
Installing Multiple PBS Licenses ...........................27
5 Installation from Source........................................... 29
Tar File ...................................................................29
Optional Components.............................................30
Build Steps..............................................................30
Building PBS ..........................................................31
Overview ................................................................32
Build Details...........................................................35
vii Table of Contents
Make File Targets .................................................. 44
Machine Dependent Build Instructions ................. 44
Install Options....................................................... 51
6 Upgrading PBS ..........................................................53
Overlay Upgrade.................................................... 53
Migration Upgrade................................................. 54
Alternate Test Systems .......................................... 57
Dependent Jobs and Test Systems ......................... 59
7 Configuring the Server .............................................61
Network Addresses and Ports ................................ 61
qmgr ....................................................................... 62
Default Configuration ............................................ 66
Server Attributes .................................................... 66
Queue Attributes .................................................... 72
Nodes ..................................................................... 78
Node Attributes...................................................... 82
SGI Weightless CPU Support................................ 86
Job Attributes ......................................................... 87
PBS Resources ....................................................... 87
Advanced Configuration Options .......................... 90
8 Configuring MOM ....................................................93
MOM Config File .................................................. 93
Job Memory Limit Enforcement.......................... 100
SGI Non-cpuset Memory Enforcement ............... 101
Job NCPUS Limit Enforcement .......................... 101
Enhanced SGI “cpusets” Support ........................ 103
Static Resources ................................................... 105
Dynamic Resources ............................................. 106
Idle Workstation Cycle Harvesting...................... 107
MOM Globus Configuration ............................... 109
Example: Single Server ....................................... 109
Example: Cluster.................................................. 109
9 Configuring the Scheduler .....................................111
Default Configuration .......................................... 111
New Scheduler Features ...................................... 113
Tunable Parameters.............................................. 115
10 Example Configurations .........................................133
Single Node Time-sharing System ...................... 134
Single Timesharing Node with Separate Server .. 135
Multi-node Timesharing Cluster.......................... 136
Multi-node Space-sharing Cluster ....................... 138
PBS Pro 5.2 viii
Administrator Guide
11 Administration.........................................................139
/etc/pbs.conf ......................................................... 139
Starting PBS Daemons......................................... 140
Stopping PBS ....................................................... 146
Checkpoint/Restart Under PBS ........................... 148
Start/Stop/Enable/Disable Queues ...................... 149
Security ................................................................ 150
Internal Security................................................... 150
External Security.................................................. 153
Root Owned Jobs ................................................. 154
Managing PBS and Multi-node Parallel Jobs ...... 154
SGI Job Container / Limits Support .................... 155
Job Prologue/Epilogue Scripts............................. 155
Use and Maintenance of Logfiles ........................ 158
Interpreting PBS Exit Codes................................ 166
PBS tracejob Command....................................... 166
Handling Jobs on Failed Nodes ........................... 168
xPBS GUI Configuration..................................... 168
xpbsmon GUI Configuration ............................... 170
pbsnodes Command ............................................. 171
Using Job Comments ........................................... 172
PBS Pro on Scyld Beowulf Clusters.................... 173
12 Problem Solving ......................................................175
Clients Unable to Contact Server......................... 175
Nodes Down ........................................................ 176
Requeueing a Job “Stuck” on a Down Node ....... 177
Non Delivery of Output ....................................... 177
Job Cannot be Executed....................................... 178
Running Jobs with No Active Processes ............. 178
Getting Help......................................................... 178
13 Customizing PBS .....................................................181
Shell Invocation ................................................... 181
Additional Build Options..................................... 183
Site Modifiable Source Files................................ 185
Implementing a Custom Scheduler...................... 187
14 Appendix A: Error Codes ......................................195
15 Index .........................................................................199
PBS Pro 5.2 ix
Administrator Guide
PBS Pro is the enhanced commercial version of the PBS software originally developed for
NASA. The NASA version had a number of corporate and individual contributors over the
years, for which the PBS developers and PBS community are most grateful. Below we
provide formal legal acknowledgements to corporate and government entities, then special
thanks to individuals.
The NASA version of PBS contained software developed by NASA Ames Research Center, Lawrence Livermore National Laboratory, and MRJ Technology Solutions. In addition, it included software developed by the NetBSD Foundation, Inc., and its contributors,
as well as software developed by the University of California, Berkeley and its contributors.
Other contributors to the NASA version of PBS include Bruce Kelly and Clark Streeter of
NERSC; Kent Crispin and Terry Heidelberg of LLNL; John Kochmar and Rob Pennington of Pittsburgh Supercomputing Center; and Dirk Grunwald of University of Colorado,
Boulder. The ports of PBS to the Cray T3e and the IBM SP SMP were funded by DoD
USAERDC, Major Shared Research Center; the port of PBS to the Cray SV1 was funded
by DoD MSIC.
No list of acknowledgements for PBS would possibly be complete without special recognition of the first two beta test sites. Thomas Milliman of the Space Sciences Center of the
University of New Hampshire was the first beta tester. Wendy Lin of Purdue University
was the second beta tester and holds the honor of submitting more problem reports than
anyone else outside of NASA.
x Acknowledgements
PBS Pro 5.2 xi
Administrator Guide
Intended Audience
This document provides the system administrator with the information required to install,
configure, and manage the Portable Batch System (PBS). PBS is a workload management
system from Veridian that provides a unified batch queuing and job management interface
to a set of computing resources.
Related Documents
The following publications contain information that may also be useful in the management and administration of PBS.
PBS Pro User Guide: Provides an overview of PBS Pro and serves
as an introduction to the software, explaining how to use the user
commands and graphical user interface to submit, monitor, track,
delete, and manipulate jobs.
PBS External Reference Specification: Discusses in detail the
PBS application programming interface (API), security within PBS,
and intra-daemon communication.
xii Preface
Ordering Software and Publications
To order additional copies of this manual and other PBS publications, or to purchase additional software licenses, contact the PBS Products Department of Veridian (or visit the
PBS Online Store). Full contact information is included on the copyright page of this document.
Document Conventions
PBS documentation uses the following typographic conventions.
If a PBS command can be abbreviated (such as subcommands
to qmgr) the shortest acceptable abbreviation is underlined.
This fixed width font is used to denote literal commands, filenames, error messages, and program output.
Literal user input is shown in this bold, fixed-width font.
Following UNIX tradition, manual page references include the
corresponding section number in parentheses appended to the
manual page name.
Words or terms being defined, as well as variable names, are in
PBS Pro 5.2 1
Administrator Guide
Chapter 1
This book, the Administrator Guide to the Portable Batch System, Professional Edition
(PBS Pro) is intended as your knowledgeable companion to the PBS Pro software. The
information herein pertains to PBS in general, with specific information for PBS Pro 5.2.
It covers both the standard binary distribution of PBS Pro, as well as the optional source
code distribution.
1.1 Book Organization
This book is organized into 13 chapters, plus an appendix. Depending on your intended
use of PBS, some chapters will be critical to you, and others can be safely skipped.
Chapter 1
Introduction: Gives an overview of this book, PBS, and the PBS
Products Department of Veridian.
Chapter 2
Concepts and Terms: Discusses the components of PBS and how
they interact, followed by definitions of terms used in PBS.
Chapter 3
Pre-Installation Planning: Helps the reader plan for a new installation of PBS.
Chapter 4
Installation: Covers the installation of the binary distribution of
2 Chapter 1
PBS and software licenses.
Chapter 5
Installation from Source: Covers the installation of PBS from
source code. This chapter can be skipped if you are installing
the binary distribution.
Chapter 6
Upgrading PBS: Provides important information for sites that
are upgrading from a previous version of PBS.
Chapter 7
Configuring the Server: Describes how to configure the PBS
Server daemon.
Chapter 8
Configuring MOM: Describes how to configure the PBS
MOM daemons.
Chapter 9
Configuring the Scheduler: Describes how to configure the
PBS Scheduler daemon.
Chapter 10
Example Configurations: Provides examples and sample configurations.
Chapter 11
Administration: Discusses PBS management and administration.
Chapter 12
Problem Solving: Discusses how to trouble-shoot PBS problems, and describes the tools provided by PBS to assist with
problem solving.
Chapter 13
Customizing PBS: Provides information on customizing PBS.
This chapter can be skipped by most sites.
Appendix A
Error Codes: Provides a listing and description of the PBS
error codes.
1.2 What is PBS Pro?
PBS Pro is the professional version of the Portable Batch System (PBS), a flexible
resource and workload management system, originally developed to manage aerospace
computing resources at NASA. PBS has since become the leader in supercomputer workload management and the de facto standard on Linux clusters.
PBS Pro 5.2 3
Administrator Guide
Today, growing enterprises often support hundreds of users running thousands of jobs
across different types of machines in different geographical locations. In this distributed
heterogeneous environment, it can be extremely difficult for administrators to collect
detailed, accurate usage data or to set system-wide resource priorities. As a result, many
computing resource are left under-utilized, while others are over-utilized. At the same
time, users are confronted with an ever expanding array of operating systems and platforms. Each year, scientists, engineers, designers, and analysts must waste countless hours
learning the nuances of different computing environments, rather than being able to focus
on their core priorities. PBS Pro addresses these problems for computing-intensive enterprises such as science, engineering, finance, and entertainment.
Now you can use the power of PBS Pro to take better control of your computing resources.
This product enables you to unlock the potential in the valuable assets you already have.
By reducing dependency on system administrators and operators, you will free them to
focus on other actives. PBS Pro can also help you to efficiently manage growth by tracking real usage levels across your systems and by enhancing effective utilization of future
1.2.1 History of PBS
In the past, UNIX systems were used in a completely interactive manner. Background jobs
were just processes with their input disconnected from the terminal. However, as UNIX
moved onto larger and larger processors, the need to be able to schedule tasks based on
available resources increased in importance. The advent of networked compute servers,
smaller general systems, and workstations led to the requirement of a networked batch
scheduling capability. The first such UNIX-based system was the Network Queueing System (NQS) from NASA Ames Research Center in 1986. NQS quickly became the de facto
standard for batch queueing.
Over time, distributed parallel systems began to emerge, and NQS was inadequate to handle the complex scheduling requirements presented by such systems. In addition, computer system managers wanted greater control over their compute resources, and users
wanted a single interface to the systems. In the early 1990’s NASA needed a solution to
this problem, but found nothing on the market that adequately addressed their needs. So
NASA lead an international effort to gather requirements for a next-generation resource
management system. The requirements and functional specification were later adopted as
an IEEE POSIX standard (1003.2d). Next, NASA funded the development of a new
resource management system compliant with the standard. Thus the Portable Batch System (PBS) was born.
4 Chapter 1
PBS was quickly adopted on distributed parallel systems and replaced NQS on traditional
supercomputers and server systems. Eventually the entire industry evolved toward distributed parallel systems, taking the form of both special purpose and commodity clusters.
Managers of such systems found that the capabilities of PBS mapped well onto cluster
The latest chapter in the PBS story began when Veridian (the R&D contractor that developed PBS for NASA) released the Portable Batch System Professional Edition (PBS Pro),
a complete workload management solution.
1.3 About Veridian
The PBS Pro product is brought to you by the same team that originally developed PBS
for NASA. In addition to the core engineering team, the Veridian PBS Products department includes individuals who have supported PBS on computers all around the world,
including the largest supercomputers in existence. The staff includes internationally-recognized experts in resource- and job-scheduling, supercomputer optimization, messagepassing programming, parallel computation, and distributed high-performance computing.
In addition, the PBS team includes co-architects of the NASA Metacenter (the first fullproduction geographically distributed meta-computing environment), co-architects of the
Department of Defense MetaQueueing Project, co-architects of the NASA Information
Power Grid, and co-chair of the Grid Forum’s Scheduling Group. Veridian staff are routinely invited as speakers on a variety of information technology topics.
Veridian is an advanced information technology company delivering trusted solutions in
the areas of national defense, critical infrastructure, and essential business systems. A private company with annual revenues of $670 million, Veridian operates at more than 50
locations in the US and overseas, and employs nearly 5,000 computer scientists and software development engineers, systems analysts, information security and forensics specialists, and other information technology professionals. The company is known for building
strong, long-term relationships with a highly sophisticated customer base.
PBS Pro 5.2 5
Administrator Guide
Chapter 2
Concepts and Terms
PBS is a distributed workload management system. As such, PBS handles the management and monitoring of the computational workload on a set of one or more computers.
Modern workload/resource management solutions like PBS include the features of traditional batch queueing but offer greater flexibility and control than first generation batch
systems (such as the original batch system NQS).
Workload management systems have three primary roles:
The collecting together of work or tasks to be run on a computer.
Users submit tasks or “jobs” to the resource management system
where they are queued up until the system is ready to run them.
The process of selecting which jobs to run when and where, according to a predetermined policy. Sites balance competing needs and
goals on the system(s) to maximize efficient use of resources (both
computer time and people time).
The act of tracking and reserving system resources and enforcing
usage policy. This covers both user-level and system-level monitoring as well as monitoring of the scheduling algorithms to see how
well they are meeting the stated goals
6 Chapter 2
Concepts and Terms
2.1 PBS Components
PBS consist of two major component types: user-level commands and system daemons. A
brief description of each is given here to help you make decisions during the installation
PBS supplies both command line programs that are POSIX
1003.2d conforming and a graphical interface. These are used
to submit, monitor, modify, and delete jobs. These client commands can be installed on any system type supported by PBS
and do not require the local presence of any of the other components of PBS.
There are three classifications of commands: user commands
(which any authorized user can use), operator commands, and
Manager (or administrator) commands. Operator and Manager
commands require specific access privileges, as discussed in
section 11.6 “Security” on page 150.
PBS Pro 5.2 7
Administrator Guide
Job Server
The Job Server daemon is the central focus for PBS. Within this
document, it is generally referred to as the Server or by the execution name pbs_server. All commands and daemons communicate
with the Server via an Internet Protocol (IP) network. The Server’s
main function is to provide the basic batch services such as receiving/creating a batch job, modifying the job, protecting the job
against system crashes, and running the job. Typically there is one
Server managing a given set of resources.
Job Executor
The Job Executor is the daemon that actually places the job into
execution. This daemon, pbs_mom, is informally called MOM as it
is the mother of all executing jobs. (MOM is a reverse-engineered
acronym that stands for Machine Oriented Miniserver.) MOM
places a job into execution when it receives a copy of the job from a
Server. MOM creates a new session that is as identical to a user
login session as is possible. For example, if the user’s login shell is
csh, then MOM creates a session in which .login is run as well
as .cshrc. MOM also has the responsibility for returning the
job’s output to the user when directed to do so by the Server. One
MOM daemon runs on each computer which will execute PBS jobs.
A special version of MOM, called the Globus MOM, is available if
it is enabled during the installation of PBS. It handles submission of
jobs to the Globus environment. Globus is a software infrastructure
that integrates geographically distributed computational and information resources. Globus is discussed in more detail in the “Globus
Support” section of the PBS User Guide.
Job Scheduler
The Job Scheduler daemon, pbs_sched, implements the site’s policy controlling when each job is run and on which resources. The
Scheduler communicates with the various MOMs to query the state
of system resources and with the Server to learn about the availability of jobs to execute. The interface to the Server is through the
same API as used by the client commands. Note that the Scheduler
interfaces with the Server with the same privilege as the PBS Manager.
8 Chapter 2
Concepts and Terms
2.2 Defining PBS Terms
The following section defines important terms and concepts of PBS. The reader should
review these definitions before beginning the planning process prior to installation of
PBS. The terms are defined in an order that best allows the definitions to build on previous
A node to PBS is a computer system with a single operating
system (OS) image, a unified virtual memory space, one or
more CPUs and one or more IP addresses. Frequently, the term
execution host is used for node. A computer such as the SGI
Origin 3000, which contains multiple CPUs running under a
single OS, is one node. Systems like the IBM SP and Linux
clusters, which contain separate computational units each with
their own OS, are collections of nodes. Nodes can be defined as
either cluster nodes or timeshared nodes, as discussed below.
Nodes & Virtual
A node may be declared to consist of one or more virtual processors (VPs). The term virtual is used because the number of
VPs declared does not have to equal the number of real processors on the physical node. The default number of virtual processors on a node is the number of currently functioning
physical processors; the PBS Manager can change the number
of VPs as required by local policy.
Cluster Node
A node whose purpose is geared toward running parallel jobs is
called a cluster node. If a cluster node has more than one virtual
processor, the VPs may be assigned to different jobs (jobshared) or used to satisfy the requirements of a single job
(exclusive). This ability to temporally allocate the entire node
to the exclusive use of a single job is important for some multinode parallel applications. Note that PBS enforces a one-to-one
allocation scheme of cluster node VPs ensuring that the VPs
are not over-allocated or over-subscribed between multiple
Timeshared Node
In contrast to cluster nodes are hosts that always service multiple jobs simultaneously, called timeshared nodes. Often the
term host rather than node is used in conjunction with timeshared, as in timeshared host. A timeshared node will never be
allocated exclusively or temporarily-shared. However, unlike
cluster nodes, a timeshared node can be over-committed if the
local policy specifies to do so.
PBS Pro 5.2 9
Administrator Guide
This is any collection of nodes controlled by a single instance of
PBS (i.e., by one PBS Server).
Exclusive VP
An exclusive VP is one that is used by one and only one job at a
time. A set of VPs is assigned exclusively to a job for the duration
of that job. This is typically done to improve the performance of
message-passing programs.
Temporarilyshared VP
A temporarily-shared node is one where one or more of its VPs are
temporarily shared by jobs. If several jobs request multiple temporarily-shared nodes, some VPs may be allocated commonly to both
jobs and some may be unique to one of the jobs. When a VP is allocated on a temporarily-shared basis, it remains so until all jobs
using it are terminated. Then the VP may be re-allocated, either
again for temporarily-shared use or for exclusive use.
If a host is defined as timeshared, it will never be allocated exclusively or temporarily-shared.
Load Balance
A policy wherein jobs are distributed across multiple timeshared
hosts to even out the workload on each host. Being a policy, the distribution of jobs across execution hosts is solely a function of the
Job Scheduler.
A queue is a named container for jobs within a Server. There are
two types of queues defined by PBS, routing and execution. A routing queue is a queue used to move jobs to other queues including
those that exist on different PBS Servers. Routing queues are similar to the old NQS pipe queues. A job must reside in an execution
queue to be eligible to run and remains in an execution queue during the time it is running. In spite of the name, jobs in a queue need
not be processed in queue order (first-come first-served or FIFO).
Node Attribute
Nodes have attributes associated with them that provide control
information. The attributes defined for nodes are: state, type
(ntype), the list of jobs to which the node is allocated, properties,
max_running, max_user_run, max_group_run, and both assigned
Node Property
A set of zero or more properties may be given to each node in order
to have a means of grouping nodes for allocation. The property is
nothing more than a string of alphanumeric characters (first charac-
10 Chapter 2
Concepts and Terms
ter must be alphabetic) without meaning to PBS. The PBS
administrator may assign to nodes whatever property names
desired. Your choices for property names should be relayed to
the users.
Portable Batch
PBS consists of one Job Server (pbs_server), one or more Job
Scheduler (pbs_sched), and one or more execution servers
(pbs_mom). The PBS System can be set up to distribute the
workload to one large timeshared system, multiple time shared
systems, a cluster of nodes to be used exclusively or temporarily-shared, or any combination of these.
The remainder of this chapter provides additional terms, listed in alphabetical order.
An account is arbitrary character string, which may have meaning to one or more hosts in the batch system. Frequently,
account is used as a grouping for charging for the use of
See Manager.
PBS provides an Application Programming Interface (API)
which is used by the commands to communicate with the
Server. This API is described in the PBS External Reference
Specification. A site may make use of the API to implement
new commands if so desired.
An attribute is an inherent characteristic of a parent object
(Server, queue, job, or node). Typically, this is a data item
whose value affects the operation or behavior of the object and
can be set by the owner of the object. For example, the user can
supply values for attributes of a job.
Batch or Batch
This refers to the capability of running jobs outside of the
interactive login environment.
A complex is a collection of hosts managed by one batch system. It may be made up of nodes that are allocated to only one
job at a time or of nodes that have many jobs executing at once
on each node or a combination of these two scenarios.
This is the location within PBS where a job is sent for
processing. A destination may uniquely define a single queue
at a single Server or it may map into many locations.
PBS Pro 5.2 11
Administrator Guide
This is a string that names the destination. It is composed two parts
and has the format queue@server where server is the name of a
PBS Server and queue is the string identifying a queue on that
File Staging
File staging is the movement of files between a specified location
and the execution host. See “Stage In” and “Stage Out” below.
Group ID (GID)
This numeric identifier is uniquely assigned to each group (see
Group refers to collection of system users (see Users). A user must
be a member of a group and may be a member of more than one.
Within UNIX and POSIX systems, membership in a group
establishes one level of privilege. Group membership is also often
used to control or limit access to system resources.
An artificial restriction which prevents a job from being selected
for processing. There are three types of holds. One is applied by the
job owner, another is applied by the operator or administrator, and
a third applied by the system itself or the PBS administrator.
Job or Batch Job
The basic execution object managed by the batch subsystem. A job
is a collection of related processes which is managed as a whole. A
job can often be thought of as a shell script running in a POSIX
session. (A session is a process group the member processes cannot
leave.) A non-singleton job consists of multiple tasks of which each
is a POSIX session. One task will run the job shell script.
The manager is the person authorized to use all restricted
capabilities of PBS. The Manager may act upon the Server, queues,
or jobs. The Manager is also called the administrator.
A person authorized to use some but not all of the restricted
capabilities of PBS is an operator.
The owner is the user who submitted the job to PBS.
This acronym refers to the various standards developed by the
“Technical Committee on Operating Systems and Application
Environments of the IEEE Computer Society” under standard
12 Chapter 2
Concepts and Terms
If a PBS job can be terminated and its execution restarted from
the beginning without harmful side effects, the job is rerunable.
Stage In
This process refers to moving a file or files to the execution
host prior to the PBS job beginning execution.
Stage Out
This process refers to moving a file or files off of the execution
host after the PBS job completes execution.
Each system user is identified by a unique character string (the
user name) and by a unique number (the user id).
Task is a POSIX session started by MOM on behalf of a job.
User ID (UID)
Virtual Processor
Privilege to access system resources and services is typically
established by the user id, which is a numeric identifier
uniquely assigned to each user (see User).
See Cluster Node.
PBS Pro 5.2 13
Administrator Guide
Chapter 3
Pre-Installation Planning
This chapter presents two sets of information needed prior to installing PBS. First, a summary of new features in this release of PBS Pro, version 5.2, is provided. Next is the information necessary to make certain planning decisions.
Be sure to read the Release Notes included in the PBS Pro distribution, as it contains information that was unavailable when this book
went to press.
3.1 New Features in PBS Pro 5.2
The following is a list of major new features in release 5.2 of PBS Pro. Full descriptions
are given in the referenced sections of the PBS Pro documentation:
MOM restart notice is now sent to Server immediately, rather than
waiting for the next polling cycle from Server.
New floating license feature has been added to the PBS Pro license
manager. See “Using Floating Licenses” on page 26.
Option to relax password requirements for sites with common user
namespace is now available. See “User Authorization” on page 151.
14 Chapter 3
Pre-Installation Planning
New per-user (hard and soft) resource run limits have been
added. See “max_user_res.RES” on page 69.
Support for SGI Job Container and Limits. See “SGI Job Container / Limits Support” on page 155.
Optional Support for DCE. See “Compiling in DCE Support”
on page 50.
Enforcement of the "ncpus" (number of CPUs) resource usage
is now available on all platforms. See “Job NCPUS Limit
Enforcement” on page 101.
Enforcement of the "mem" (physical memory) resource usage is
now available on all platforms. See “Job Memory Limit
Enforcement” on page 100.
Support for SGI “weightless” CPUs has been added. See “SGI
Weightless CPU Support” on page 86.
Enhanced SGI memory usage calculations now performed. See
“SGI Non-cpuset Memory Enforcement” on page 101.
Enhanced support for SGI “cpusets”. See “Enhanced SGI
“cpusets” Support” on page 103.
Support for suspension and checkpoint of multi-node jobs. See
“Suspending/Checkpointing Multi-node Jobs” on page 148.
Optional checkpointing support prior to IRIX OS upgrades. See
“Checkpointing Jobs Prior to SGI IRIX Upgrade” on page 149.
“Cycle Harvesting” of otherwise unused workstations (also
known as “cycle stealing” has been added. See “Idle Workstation Cycle Harvesting” on page 107.
Enhancements to fairshare scheduling. See “Site-Specified
Fairshare Resources” on page 114.
Enhanced job preemption features. See “Preemption Enhancement” on page 113.
PBS Pro 5.2 15
Administrator Guide
New node/resource specification language. See “New Resource
Specification” in the PBS User Guide.
New temporary scratch directory created automatically for jobs. See
“TMPDIR” in the PBS User Guide.
Features for using PBS within a DCE environment. See “Using PBS
with DCE” in the PBS User Guide.
Server - MOM Protocol Change
The Server - MOM protocol has changed in release 5.2. Therefore a 5.2 Server cannot
communicate with a MOM from a prior version, nor can a 5.2 MOM communicate with a
Scheduler of an earlier version.
Changes to Time-shared and Cluster Nodes
For planning purposes, note PBS Pro 5.1 reduced the differences between time-shared and
cluster nodes to:
Time-shared nodes are first choice for jobs that do not have a node
Time-shared nodes may not be requested for exclusive use with the
#excl suffix.
More processes than CPUs can be run on time-shared nodes but not
on cluster nodes.
If load balancing by "load average" is activated in the Job Scheduler, it applies only to time-shared nodes.
Allocation of cluster nodes remains based on the number of (virtual) processors.
PBS is able to support a wide range of configurations. It may be installed and used to control jobs on a single system or to load balance jobs on a number of systems. It may be used
to allocate nodes of a cluster or parallel system to both parallel and serial jobs. It can also
deal with a mix of these situations.
16 Chapter 3
Pre-Installation Planning
3.4.1 Single Timesharing System
If PBS is to be installed on a time-sharing system, all three daemons may reside on that
system; or you may place the Server (pbs_server) and/or the Scheduler
(pbs_sched) on a “front end” system. MOM (pbs_mom) must run on the system where
jobs are to be executed.
3.4.2 Timesharing Cluster
If PBS is to be installed on a collection of time-sharing systems, a MOM must be on each
execution host and the Server and Scheduler may be installed on one of the systems or on
a front end system.
3.4.3 Large SMP systems
For large SMP systems (e.g. SGI Origin or Cray vector systems) it is best to plan on treating these as “time-shared” systems rather than “cluster nodes”, in order to maximize the
scheduling efficiency on these systems. In fact, to use the “cpuset” feature of an SGI Origin 2000/3000 system, you must declare the node as “time-shared”.
3.4.4 Running on Scyld Beowulf Clusters
If installing PBS on a Scyld Beowulf cluster, note that the cluster is controlled by a central
"master node" which will run a single MOM. There is no need to have PBS installed on
any of the compute nodes of a Scyld Beowulf cluster.
Interfacing with Globus
If Globus support is enabled, then a separate pbs_mom_globus must be run on the
same host where the pbs_server is running. Globus-specific configuration information
is given throughout the PBS documentation. Specifically, the following sections should be
reviewed by any site wishing to deploy PBS with Globus support enabled.
“Globus Toolkit” on page 30
“Server Support for Globus” on page 92
“MOM Globus Configuration” on page 109
“Manually Starting Globus MOM” on page 146
“Globus Support” in the PBS User Guide.
PBS Pro 5.2 17
Administrator Guide
Single Execution System
If you are installing PBS on a single system, you are ready to install, configure the daemons, and select your scheduling policy.
All daemons on a single host.
If you wish, the PBS Server and Scheduler, pbs_server and pbs_sched, can run on
one system and jobs can execute on another. This is a trivial case of multiple execution
systems discussed in the next section.
Single execution host.
18 Chapter 3
Pre-Installation Planning
Multiple Execution Systems
If you are planning to run PBS on more than one computer, you will need to install the
execution daemon (pbs_mom) on each system where jobs are expected to execute. The
following diagram illustrates this for an eight node cluster.
Execution Host
Execution Host
Execution Host
Execution Host
Execution Host
Execution Host
Execution Host
Execution Host
PBS Pro 5.2 19
Administrator Guide
Chapter 4
This chapter discusses the installation procedures for the PBS binary distribution package.
This is the normal installation method for most sites. However, if you intend to install
from the source code package, you should skip this chapter and read Chapter 5 “Installation from Source” on page 29.
Be sure to read the Release Notes included in the PBS Pro distribution, as it will contain any information that was unavailable when
this book went to press. The Release Notes also contain a detailed
description of all new features in a given release.
4.1 Overview
The PBS software can be installed from the PBS CD-ROM or downloaded from the PBS
website. The installation procedure is slightly different depending on the distribution
source. However, the basic steps of PBS installation are:
Step 1
Step 2
Step 3
Step 4
Prepare distribution media
Extract and install the software
Acquire a PBS license
Install the license
20 Chapter 4
4.2 Media Setup
If installing from the PBS CD-ROM, follow these instructions, with superuser privilege to
set up the media for installation:
Step 1
Step 2
Insert the PBS CD into the system CD-ROM drive
If your systems doesn’t run an automounter daemon for the CDROM drive, then you’ll need to manually mount the CD-ROM
onto the system:
# mount /cdrom
Step 3
Change directory to the mount point
# cd /cdrom
If not installing from CD-ROM, follow these instructions:
Step 1
Step 2
Download the distribution file from the PBS website. (Follow
the instructions you received with your order confirmation.)
Move distribution file to /tmp on the system on which you
intend to install PBS,
then, as superuser:
Step 3
Step 4
Step 5
Step 6
Create a temporary location under /tmp from which to install
the distribution
Change directory to the temporary installation directory
Uncompress the distribution file
Extract the distribution file
mkdir /tmp/pbs_tmp
cd /tmp/pbs_tmp
gunzip /tmp/pbspro_5_2.tgz
tar -xvf /tmp/pbspro_5_2.tar
cd PBSPro_5_2
PBS Pro 5.2 21
Administrator Guide
4.3 Default Install Options
The installation program installs the various PBS components into specific locations on
the system. The installation program allows you to override these default locations if you
wish. (Note that some operating systems’ software installation programs do not permit
software relocation, and thus you are not able to override the defaults on those systems.)
The locations are written to the /etc/pbs.conf file created by the installation process.
For details see the description of “/etc/pbs.conf” on page 139.
4.4 Installation on UNIX/Linux Systems
For a given system, the PBS install script uses the native package installer provided with
that system. This means that the PBS package should install into what is considered the
“normal” location for third-party software. The following examples shows a typical installation under the Sun Solaris operating system. The process is very similar for other operating systems, but may vary depending on the native package installer on each system.
Installation of PBS
The following directory will be the root of the
installation. Several subdirectories will be created
if they don't already exist: bin, sbin, lib, man and
Execution directory? [/opt/pbs]
PBS needs to have a private directory (referred to as
"PBS_HOME" in the documentation) where it can permanently
store information.
Home directory? [/usr/spool/PBS]
/usr/spool/PBS does not exist, I'll make it.
[ Description of the different configuration options ]
PBS Installation:
1. Server, execution and commands
2. Execution only
3. Commands only
22 Chapter 4
You need to decide what kind of PBS installation you want for each machine in your cluster. There are three possibilities: a Server node, an execution node, or a client host. If you
are going to run PBS on a single timesharing host, install the full Server package (option
1). If you are going to have a cluster of machines, you need to pick one to be the front end
and install the Server package (option 1) there. Then, install the execution package (option
2) on all the compute nodes in the cluster. The client package (option 3) is for hosts which
will not be used for execution but need to have access to PBS. It contains the commands,
the GUIs and man pages. This gives the ability to submit jobs and check status.
The following sections illustrate the differences between installation on a single server
system versus a cluster of workstations.
4.4.1 Installation on a Single UNIX Server
For the following examples, we will assume that you are installing PBS on a single large
Server/execution host, on which all the daemons will run, and from which users will submit jobs. Example of such a system might be an SMP system such as an SGI Origin3000
or a Cray T90.
To achieve this, we select option 1 to the question shown in the example above, followed
by “all” when asked which packages to add, as shown:
(1|2|3)? 1
Installing PBS for a Server Host.
The following packages are available:
1 pbs64
(sparc) 5.0
Select package(s) you wish to process (or 'all' to process
all packages). (default: all) [?,??,q]: all
Veridian Systems PBS department
## Processing package information.
## Processing system information.
## Verifying disk space requirements.
## Checking for conflicts with packages already installed.
## Checking for setuid/setgid programs.
Next the installation program will ask you to confirm that it is acceptable to install setuid/
setgid programs as well as to run installation sub-programs as root. You should answer yes
(or “y”) to both of these questions, as shown below.
PBS Pro 5.2 23
Administrator Guide
## Checking for setuid/setgid programs.
The following files are being installed with setuid and/or
setgid permissions:
/opt/pbs/sbin/pbs_iff <setuid root>
/opt/pbs/sbin/pbs_rcp <setuid root>
Do you want to install these as setuid/setgid files
[y,n,?,q] y
This package contains scripts which will be executed with
super-user permission during the process of installing
this package.
Do you want to continue with the installation of <pbs64>
[y,n,?] y
Next, the installation program will proceed to extract and install the PBS package(s) that
you selected above. The process should look similar to the example below.
Installing pbs64 as <pbs64>
## Installing part 1 of 1.
[ listing of files not shown for brevity ]
## Executing postinstall script.
*** PBS Installation Summary
*** The PBS Server has been installed in /opt/pbs/sbin.
*** The PBS commands have been installed in /opt/pbs/bin.
*** This host has the PBS Server installed, so
*** the PBS commands will use the local server.
*** The PBS command server host is mars
*** PBS Mom has been installed in /opt/pbs/sbin.
*** The PBS Scheduler has been installed in /opt/pbs/sbin.
Installation of <pbs64> was successful.
24 Chapter 4
4.4.2 Installing MOM with SGI “cpuset” Support
PBS Pro for SGI IRIX systems provides optional (site-selectable) support for IRIX
“cpusets”. A cpuset is a named region of the SGI system which contains a specific set of
CPUs and associated memory. PBS has the ability to use the cpuset feature to “fence” PBS
jobs into their own cpuset. This helps to prevent different jobs from interfering with each
other. To enable use of this feature, a different PBS MOM binary needs to be installed, as
/etc/init.d/pbs stop
cd /usr/pbs/sbin
rm pbs_mom
ln -s pbs_mom.cpuset pbs_mom
Additional information on configuring and using IRIX cpusets is discussed later in this
manual. For scheduler configuration details, see section 9.3.1 “Scheduler Support for SGI
IRIX cpusets” on page 122.
4.5 Installation on Windows 2000 Systems
When PBS is installed on a cluster, a MOM daemon must be on each execution host, and
the Server and Scheduler should be installed on one of the systems or on a front-end system.
For Windows 2000 clusters, PBS is provided in a single package that contains:
the PBS Administrator Guide in PDF form,
the PBS User Guide in PDF form,
the PBS Pro software, and
supporting text files (software license, README, release notes, etc.)
The PBS Pro install program will walk you through the installation process. If you are
installing from the PBS Pro CD-ROM, insert the CD-ROM into your computer’s CDROM drive, browse to your CD-ROM drive, and double-click on the Install program icon.
Alternatively, you can download the latest PBS Pro package from the PBS Pro Web site,
and save it to your hard drive. From there you can manually run the self-extracting
pbspro.exe package, and then the installation program, as shown below.
PBS Pro 5.2 25
Administrator Guide
C:\> pbspro.exe
C:\> install.bat
Note that you must be logged in as Administrator to run the PBS
installation program.
The installation program will prompt you for the names of directories for the different
parts of PBS and the type of installation (full, server-only, execution host only). Next, you
will be prompted for your software license key(s), as discussed in the following section.
4.6 Installing the PBS License
The PBS license manager can handle multiple license keys in the PBS license file. This is
useful when you expand your PBS configuration, you can simply add the additional
licenses. This section describes adding a single license (such as following an initial installation of PBS Pro). The next section discusses adding multiple licenses.
Note that when requesting or generating your license key(s), the number of CPUs field
should correspond with the total number of actual CPUs on which you wish to run PBS
When the installation of PBS is complete, you will need to install your PBS license key. If
you already have your PBS license key, type it in when prompted by the license installation program, as shown below.
26 Chapter 4
PBS license installation
Using /usr/spool/PBS as PBS_HOME
To get a license, please visit
or call PBSpro toll free at 877-905-4PBS
and have the following information handy:
host name:
host id:
site id from the PBSPro package
number of cpus you purchased
Please enter the license string(s) (^d to end).
? 5-00020-99999-0044-PfV/fjuivg-5Jz
Installing: 5-00020-99999-0044-PfV/fjuivg-5Jz
Please enter the next license string(s) (^d to end).
Would you like to start PBS now (y|[n])? n
To start PBS, type '/etc/init.d/pbs start'
At this point, you can probably safely skip forward to Chapter 7 “Configuring the Server”
on page 61.
However, if you have not yet received your PBS license key, follow the instructions
printed by the installation program (see example above) to receive your key. Then rerun
the PBS license key installation program as root:
# /usr/pbs/etc/pbs_setlicense
4.7 Using Floating Licenses
New in release 5.2, PBS can use a feature called floating licenses. With floating licenses,
you may have more CPUs configured online than the number of CPUs licensed. Nodes
become licensed as needed to run jobs up to the number of floating licenses. The licenses
are released from a node when no jobs remain running on the node.
The Server attribute "Licenses" shows the number of floating licenses currently available.
PBS Pro 5.2 27
Administrator Guide
A node attribute "pcpus" show the number of physical CPUs on the node, which determines the number of licenses required for that node. Another node attribute "license"
shows the node "license state":
licensed with a node-lock or fixed license
licensed with a floating license
4.8 Installing Multiple PBS Licenses
As mentioned earlier, it is possible to add multiple licenses to the PBS License file. This
can be done during installation of PBS Pro, or at some future time. If the installation program detects that you already have a PBS license file, it will prompt you as to what you
want done: keep the file, replace the file, or append to it. Specify the option that corresponds to the action you wish to take.
Then, if you have multiple license keys, simply type them in when prompted by the
license installation program, as shown in the example below.
Note that you can invoke the license key installation program directly (as may be needed
following an increase in the size of the system or cluster managed by PBS), using the “-a”
(append) option:
# /usr/pbs/etc/pbs_setlicense -a
28 Chapter 4
PBS license installation
Using /usr/spool/PBS as PBS_HOME
A license already exists in
Would you like to (k)eep it, (r)replace it, (a)ppend to
it, or (q)uit
([k]|a|q)? a
To get a license, please visit
or call PBSpro toll free at 877-905-4PBS
and have the following information handy:
host name:
host id:
site id from the PBSPro package
number of cpus you purchased
Please enter the license string(s) (^d to end).
? 5-00020-99999-0044-PfV/fjuivg-5Jz
Installing: 5-00020-99999-0044-PfV/fjuivg-5Jz
Please enter the next license string(s) (^d to end).
? 5-00020-99999-0010-XdsXdfssf-5Xj
Installing: 5-00020-99999-0010-XdsXdfssf-5Xj
Please enter the next license string(s) (^d to end).
Would you like to start PBS now (y|[n])? n
To start PBS, type '/etc/init.d/pbs start'
PBS Pro 5.2 29
Administrator Guide
Chapter 5
Installation from Source
This chapter explains how to build and install PBS from the source code distribution. If
you are installing from the binary distribution package, you should skip this chapter, and
continue with Chapter 7 “Configuring the Server” on page 61.
5.1 Tar File
The PBS source distribution is provided as a single tar file. The tar file contains:
This document in both postscript and PDF form.
A “configure” script, and all source code, header files, and
make files required to build and install PBS.
A full set of manual page sources. These are troff input files.
When the PBS tar file is extracted, a subtree of directories is created
in which all the above mentioned files are created. The name of the
top level directory of this subtree will reflect the release version and
patch level of the version of PBS being installed. For example, the
directory for PBS Pro 5.2 will be named pbspro_5_2_0.
30 Chapter 5
Installation from Source
5.2 Optional Components
To build PBS from source and to include support for optional features, several third party
applications are required. This section describes these additional requirements.
5.2.1 POSIX make
PBS uses a configure script, generated by GNU’s autoconf facility, to produce
makefiles. If you have a POSIX-compliant make program then the makefiles generated
by configure will try to take advantage of POSIX make features. If the make program
that exists on your system is unable to process the makefiles, try using GNU’s make program.
5.2.2 tcl/tk
If the Tcl/tk based GUI (xpbs and xpbsmon) or a Tcl based custom Scheduler is used,
the Tcl header files and libraries are required. Versions of Tcl prior to 8.0 cannot be used
with PBS. The official site for Tcl is:
5.2.3 Globus Toolkit
If the Globus feature is to be enabled, ensure that Globus clients and libraries are installed.
Check the following site for obtaining the Globus software:
5.3 Build Steps
To generate a usable PBS installation, the following steps are required. Each step is
explained in detail in the subsequent sections of this book.
Step 1
Read this guide and plan a general configuration of hosts and
Step 2
Decide where the PBS source and objects are to go. See also
section 3.4 “Planning” on page 15.
PBS Pro 5.2 31
Administrator Guide
Step 3
Unzip and untar the distribution file into the source tree. See section
5.5 “Overview” on page 32.
Step 4
Change the current working directory to that directory which is to
be the top of the object tree. See section 5.5 “Overview” on page 32.
Step 5
Select “configure” options and run configure from the top of the
object tree. See section 5.6 “Build Details” on page 35.
Step 6
Compile the PBS modules by typing make at the top of the object
tree. See section 5.7 “Make File Targets” on page 44.
Step 7
As superuser, change directory to the top of the object tree, and
install the PBS modules by typing make install.
Step 8
As superuser, complete the installation of PBS and set up license
key file by typing make postinstall.
Step 9
Choose and follow a method for installing MOM. See section 5.9
“Install Options” on page 51.
Details of building PBS are given below. After installation, you can continue with Chapter
7 “Configuring the Server” on page 61 of this manual. If, however, you are planning to use
an alternate scheduler you may wish to read section 13.4 “Implementing a Custom Scheduler” on page 187 before continuing with the configuration of PBS.
5.4 Building PBS
This section explains in detail the steps to build and install PBS. In the following descriptions, the source tree is the subtree that gets created when the PBS tarfile is extracted. The
target tree is the subtree of parallel directories in which the object modules are actually
compiled. This tree may (and generally should) be separate from the source tree. So it is
recommended that you create a separate directory to be the top of the target tree. The target tree is fleshed out with subdirectories and makefiles when configure is run.
The PBS build and installation process is accomplished using the make file and subdirectories that got created by running configure, a script created for PBS using GNU’s
32 Chapter 5
Installation from Source
autoconf facility. You should change directory to the top level of the PBS target tree when
doing the build and subsequent installation of PBS. This installation procedure requires
more manual configuration than is “typical” for many packages. There are a number of
options which involve site policy and therefore cannot be determined automagically.
5.5 Overview
The normal PBS build procedure is to separate the source tree from the target tree. This
allows the placement of a single copy of the source on a shared file system from which
multiple different target systems can be built. Also, the source can be protected from accidental destruction or modification by making the source read-only. However, if you
choose, objects may be made within the source tree.
An overview of the “configure”, compile, installation and PBS configuration steps is
listed here. Detailed explanation of symbols will follow. It is recommended that you read
completely through these instructions before beginning the installation. To install PBS:
Step 1
Place the tar file on the system where you would like to maintain the source.
Step 2
Untar the tar file. For example:
# cd /usr/local/src
# tar xpf /CDROM/PBSPro_5.2.tar
It will untar in the current directory producing a single directory
named for the current release and patch number. Under that
directory will be several files and subdirectories. This directory
and the subdirectories make up the source tree. You may writeprotect the source tree at this point should you so choose.
In the top directory are two files, named Release_Notes
and INSTALL. The Release_Notes file contains information about the release contents, changes since the last release
and a reference to this guide for installation instructions. The
INSTALL file consists of standard notes about the use of
GNU’s configure.
PBS Pro 5.2 33
Administrator Guide
Step 3
If you choose (as recommended) to have separate target and source
trees, then create the top level directory of what will become the target tree at this time. The target tree must reside on a file system
mounted on the same architecture as the target system for which you
are generating the PBS binaries. This may be the same system that
holds the source or it may not. Change directory to the top of the target tree. For example,
cd /usr/local/pbs/obj
Step 4
Make a job Scheduler choice. A unique feature of PBS is its external Scheduler module. This allows a site to implement any policy of
its choice. To provide even more freedom in implementing policy,
PBS provides two Scheduler frameworks. Schedulers may be developed in the C language, or the Tcl scripting language.
As distributed, configure will default to a C language based
Scheduler known as Standard. This Scheduler can be configured to
several common scheduling policies. When this Scheduler is
installed, certain configuration files are installed in
/usr/spool/PBS/sched_priv/. You will need to modify
these files for your site. These files are discussed in Chapter 9 “Configuring the Scheduler” on page 111.
To change the selected Scheduler, see the two configure options
--set-sched and --set-sched-code in the Features and
Package Options section of this chapter. Additional information on
the use and configuration of other Schedulers can be found in section 13.4 “Implementing a Custom Scheduler” on page 187.
Step 5
Read section 5.6 “Build Details” on page 35 then, from within the
top of the target tree created in step 3, type the following command
# /usr/local/src/pbspro_52/configure [options]
If you are building at the top of the source tree, type
./configure [options]
This will generate the complete target tree (starting with the current
working directory), a set of header files, and all the make files
34 Chapter 5
Installation from Source
needed to build PBS. Re-running the configure script will
only need to be done if you choose to change options specified
on the configure command line. See section 5.6 “Build Details”
on page 35 for information on the configure options, or type
./configure --help
No options are absolutely required. Note that while GNU’s C
compiler (gcc) will work with PBS, the vendor supplied C compiler is usually preferable. If you wish to build the GUI to PBS,
and the Tcl libraries are not in the normal place (/usr/
local/lib) then you will need to specify --withtcl=directory giving the path to the Tcl libraries. If you
want to enable Globus support within PBS, then you will need
to specify the definitions for SSL_DIR and LDAP_DIR directories using --with-globus=DIR.
Running configure without any (other) options will prepare
the build process to produce a working PBS system with the
following defaults (which can be overridden as described
User commands are installed in /usr/local/bin.
Daemons and administrative commands are installed in
Working directory for the daemons is /usr/spool/PBS
C-based Standard Scheduler will be selected
Because the number of options you select may be large and
because each option is rather wordy you may wish to create a
shell script consisting of the configure command and the
selected options.
Step 6
After running the configure script, the next step is to compile PBS by typing
from the top of the target tree.
Step 7
To install PBS you must be running with root privileges. As
root, type
make install
PBS Pro 5.2 35
Administrator Guide
from the top of the target tree. This generates the working directory
structures required for running PBS and installs the programs in the
proper executable directories.
When the working directories are made, they are also checked to see
that they have been setup with the correct ownership and permissions. This is performed to ensure that files are not tampered with
and the security of PBS and your system are not compromised.
Running make install will create the /etc/pbs.conf file,
or if it already exists then /etc/pbs.conf.new containing the
locations for the executables and PBS_HOME set to what was specified on the configure options. (For details, see “/etc/pbs.conf” on
page 139.)
Step 8
Complete the installation of PBS and set up the license key file by
typing, as root:
make postinstall
First the postinstall program will create the PBS Server database (if it doesn’t already exist). When complete, it will contain the
default queue and Server configuration described throughout this
Next, postinstall will run pbs_setlicense which will
prompt you for your PBS license key(s). For a full description of the
license key installation process, with examples, see “Installing the
PBS License” on page 25.
5.6 Build Details
While the overview gives sufficient information to build a basic PBS system, there are lots
of options available to allow you to custom tailor PBS to suite your specific environment.
The following tables list detailed information on the options to the configure script.
This information is broken into three separate tables: generic configure options, directory and file options, and feature-specific options.
36 Chapter 5
Installation from Source
The table below lists the generic configure options available. These alter the behavior of
configure itself, and therefore do not affect the functionality of PBS.
Generic Configure Options
Description and Defaults
Cache the system configuration test results in file
Default: config.cache
Prints out information on the available options.
Do not create output files.
Do not print “checking” messages.
Print the version of autoconf that created configure.
Turn on configure’s ability to cache makedepend
information across runs of configure. This can be
bad if the user makes certain configuration changes
and reruns configure, but it can save time in the
hands of experienced developers.
Default: disabled
This second table lists configure options which allow you to specify the directories in
which the PBS objects will be placed, as well as the location of specific files.
Directory and File Options
Description and Defaults
Install files in subdirectories of directory PREFIX
Default: /usr/local
Install architecture dependent files in subdirectories
of EPREFIX. The value specified will be written to
the /etc/pbs.conf file.
Default: PREFIX (/usr/local)
Install user executables (commands) in subdirectory
Default: EPREFIX/bin (/usr/local/bin)
Install System Administrator executables in subdirectory DIR. This includes certain administrative
commands and the daemons.
Default: EPREFIX/sbin (/usr/local/sbin)
PBS Pro 5.2 37
Administrator Guide
Directory and File Options
Description and Defaults
Object code libraries are placed in DIR. This
includes the PBS API library, libpbs.a.
Default: PREFIX/lib (/usr/local/lib
C language header files are installed in DIR.
Default: PREFIX/include (/usr/local/include)
Install man pages in DIR.
Default: PREFIX/man (/usr/local/man)
PBS sources can be found in directory TREE.
Default: location of the configure script.
X11 header files are in directory DIR.
Default: attempts to autolocate the header files
X11 libraries are in directory DIR.
Default: attempts to autolocate the libraries
Adding this option will enable Globus support
within PBS. This will search DIR for the Globus
makefile_header. This option will cause a separate pbs_mom_globus daemon to be compiled and
directories created.
Searches SSLDIR for the SSL include files and
libraries. Use this option only if --with-globus
could not expand SSL_DIR.
Searches DIR for the OpenLDAP include files and
libraries. Use this option only if --with-globus
could not expand LDAP_DIR.
This third table lists the feature-specific options to configure. In general, these options
take the following forms:
Do not compile for FEATURE, same as
Compile for FEATURE
Compile to include PACKAGE
Do not compile to include PACKAGE, same as
Set the value of OPTION
38 Chapter 5
Installation from Source
The recognized feature/package specific options of PBS are:
Feature Option
Description and Default
Build (or not build) the PBS Job Server, pbs_server.
Normally all components (Commands, Server, MOM,
and Scheduler) are built.
Default: enabled
Build (or not build) the PBS job execution daemon,
Default: enabled
Build (or not build) the PBS commands.
Default: enabled
Set the name of the file that will contain global information about the PBS installation including paths and
port numbers. This value may be overridden at runtime
by setting the PBS_CONF_FILE environment variable.
If a full path is not provided, the filename is relative to
the server home directory.
Default value is /etc/pbs.conf.
Define machine type to build PBS for, if not the same
as returned by uname.
Use this to specify the root directory where DCE is
Use this to set the root directory where the DES crypto
package is installed. This package needs to be available
if --with-dce is specified.
Use this option if you wish Tcl based PBS features
compiled and the Tcl libraries are not in /usr/
local/lib. These Tcl based features include the
GUI interface, xpbs and xpbsmon. If the following
option, --with-tclx, is set, use this option only if
the Tcl libraries are not co-located with the Tclx libraries. When set, TDIR must specify the absolute path of
the directory containing the Tcl Libraries.
Default: if --enable-gui is enabled, Tcl utilities
are built; otherwise they are not built.
PBS Pro 5.2 39
Administrator Guide
Feature Option
Description and Default
Use this option if you wish the Tcl based PBS features
to be based on Tclx.
This option implies --with-tcl.
Default: Tclx is not used.
Build the xpbs and xpbsmon GUI. Only valid if -with-tcl is set.
Default: enabled
Specify which C compiler should be used. This will
override the CC environment setting. If only --setcc is specified, then CC will be set to cc
Default: gcc (after all, configure is from GNU also)
Set the compiler flags. This is used to set the CFLAGS
variable. If only --set-cflags is specified, then
CFLAGS is set to “”.
Default: CFLAGS is set to a best guess for the system
Builds PBS with debug features enabled. This causes
the daemons to remain attached to standard output and
produce vast quantities of messages.
Default: disabled
Set the temporary directory in which pbs_mom will
create temporary scratch directories for jobs. Used on
Cray systems only.
Default: /tmp
Set the name of the host that clients will contact when
not otherwise specified in the command invocation. It
must be the primary network name of the host. The
value specified will be written to /etc/pbs.conf.
Default: the name of the host on which PBS is being
40 Chapter 5
Installation from Source
Feature Option
Description and Default
Sets the top level directory name for the PBS working
directories, PBS_HOME. This directory MUST reside
on a file system which is local to the host on which
any of the daemons are running. That means you must
have a local file system on any system where a
pbs_mom is running as well as where pbs_server and/
or pbs_sched is running. PBS uses synchronous writes
to files to maintain state. We recommend that the file
system has the same mount point and path on each
host, that enables you to copy daemons from one system to another rather than having to build on each system. The value specified will be written to /etc/
Default: /usr/spool/PBS
Set the file name which will contain the name of the
default Server. This file is used by the commands to
determine which Server to contact. If FILE is not an
absolute path, it will be evaluated relative to the value
of --set-server-home, PBS_HOME. The value
specified will be written to the /etc/pbs.conf file.
Default: server_name
Set the path name of the file containing the environment variables used by the daemons and placed in the
environment of the jobs. For AIX based systems, we
suggest setting this option to /etc/environment.
Relative path names are interpreted relative to the
value of --set-server-home, PBS_HOME. The
value specified will be written to /etc/pbs.conf.
Default: the file pbs_environment in the directory
Enable the use of syslog for error reporting. This is in
addition to the normal PBS logs.
Default: disabled
PBS Pro 5.2 41
Administrator Guide
Feature Option
Description and Default
Enable daemons to lock themselves into memory to
improve performance. The argument WHICH is the bitwise-or of 1 for pbs_server, 2 for pbs_sched, and 4 for
pbs_mom (7 is all three daemons). This option is recommended for Unicos systems. It must not be used for
AIX systems. Note, this feature uses the plock() system
call which is not available on Linux and bsd derived
systems. Before using this feature, check that plock(3)
is available on the system.
Default: disabled.
Set the Scheduler (language) type. If set to cc a C
based Scheduler will be compiled. If set to tcl, a Tcl
based Scheduler will be used. If set to no, no Scheduler will be compiled.
Default: cc
Sets the name of the file or directory containing the
source for the Scheduler. This is only used for C
Schedulers, where --set-sched is set to cc. For C
Schedulers, this should be a directory name. If the path
is not absolute, it will be interpreted relative to
Default: standard (C based Scheduler)
Builds qstat with the Tcl interpreter extensions. This
allows site and user customizations. Only valid if
--with-tcl is already present.
Default: disabled
Set the character to be used as the separator character
between attribute and resource names in Tcl/Tclx
Default: “.”
42 Chapter 5
Installation from Source
Feature Option
Description and Default
Set the character to be used as the man page section
suffix letter. For example, the qsub man page is
installed as man1/qsub.1B. To install without a suffix, --set-mansuffix=””.
Default: “B”
Set the name of the file that qstat will use if there is no
.qstatrc file in the user’s home directory. This option is
only valid when --enable-tcl-qstat is set. If
FILE is a relative path, it will be evaluated relative to
the PBS Home directory, see --set-server-home.
Default: PBS_HOME/qstatrc
Directs PBS to attempt to use the Secure Copy Program scp when copying files to or from a remote host.
This option cause PBS_SCP to be set in /etc/
pbs.conf with the indicated path.
Default: sbindir/pbs_rcp
When enabled, pbs_mom passes the name of the job
script to the top level shell via a pipe. If disabled, the
script file is the shell’s standard input file.
Default: enabled
Use the Reliable Packet Protocol, RPP, over UDP for
resource queries to MOM by the Scheduler. If disabled,
TCP is used instead.
Default: enabled
Build PBS with support for SGI Origin2000 nodemask.
Requires Irix 6.x.
Default: disabled
Build PBS on Cray T3e with support for Scheduler
controlled pe-specific job placement. Requires Unicos/
Default: disabled
This option has been removed.
PBS Pro 5.2 43
Administrator Guide
Feature Option
Description and Default
Turn on special features for the IBM SP. This option is
only valid when the PBS machine type is aix4. The
PBS machine type is automatically determined by the
configure script.
With PSSP software before release 3.1, access to two
IBM supplied libraries, libjm_client.a and libSDR.a,
are required. These libraries are installed when the
ssp.clients fileset in installed, and PBS will expect to
find them in the normal places for libraries.
With PSSP 3.1 and later, libjm_client.a and libSDR.a
are not required, instead libswitchtbl.a is used to load
and unload the switch. See the discussion under the
sub-section IBM SP in section 5.8 “Machine Dependent Build Instructions” on page 44.
Default: disabled
Setting this under Irix 6.x forces the use of cpusets.
Cpuset is a named set of CPUs where member processes are to be run. Enabling this feature does not use
Array Session tracking; instead, jobs are tracked by
session ids.
Default: disabled
Setting this option will send pbs_rcp file transfer statistics to the system’s log file. pbs_rcp is the default
file transfer utility used by PBS to deliver user’s input/
output/error files. In order for this option to work,
ensure that LOG_INFO, LOG_DELAY, or
LOG_LOCAL4 messages are enabled for your syslog.
Default: disabled
44 Chapter 5
Installation from Source
5.7 Make File Targets
The following target names are applicable for make:
The default target, it compiles everything.
Same as all.
Builds the header file dependency rules.
Installs everything.
Removes all object and executable files in the current subtree.
Leaves the object tree very clean. It will remove all files that
were created during a build.
Runs the script that installs the PBS license key(s).
5.8 Machine Dependent Build Instructions
There are a number of possible variables that are only used for a particular type of
machine. If you are not building for one of the following types, you may ignore this section.
5.8.1 Linux
Redhat Linux version 4.x-7.x are supported with no special configure options
5.8.2 Sun Solaris Systems
On Solaris systems, if the system has more than 2GB of physical memory, PBS must be
built with --set-cflags="-g -xarch=v9", in order to correctly calculate memory
5.8.3 Digital UNIX
The following is the recommended value for CFLAGS when compiling PBS under Tru64
4.0D: --set-cflags="-std1", that is s-t-d-one.
5.8.4 HP-UX
When building from source under HPUX, the following environment variables must be
defined before running "configure":
PBS Pro 5.2 45
Administrator Guide
setenv CC cc
setenv AR ar
CC=cc; export CC
AR=ar; export AR
For HP-UX 11.x, pbs_mom must be built as a 64 bit object, i.e.:
The libraries must match of course. If you desire, you may rebuild the rest of PBS as a 32
bit object.
Under HP-UX 11.x, Tcl and Tk are not located in the directory expected by PBS’s configure script. You will need to make a common directory for Tcl and Tk and point to it by setting
If building for a V2500 or N4000 system with PA8500 processors, also set the following
variable for performance reasons:
CCOPTS=+DA2.0 ; export CCOPTS
If building for a PA2 system on which you may run 64 bit programs, you must build PBS
with the following option added to CFLAGS so that PBS can correctly monitor memory
use of 64 bit programs:
--set-cflags="-D_PSTAT64 -Ae"
The following is the recommended value for CFLAGS when compiling PBS under HPUX 10.x:
5.8.5 IBM Workstations
PBS supports IBM workstations running AIX 4.x, however the AIX man(1) command has
difficulty with the PBS man pages. When man pages are installed in mandir the default
man page file name suffix, “B”, must be removed. This can be accomplished with the con-
46 Chapter 5
Installation from Source
figure option --set-mansuffix=””. Also, do not use the configure option:
on AIX workstations as it will crash the system by reserving all system memory.
5.8.6 IBM SP
Everything under the discussion about IBM Workstations also applies to the IBM SP
series. Be sure to read the section 3.7 “Multiple Execution Systems” on page 18 before
configuring the Server.
Set the special SP option, --enable-sp2 to compile special code to deal with the SP
high speed switch.
If the library libswitchtbl.a is not detected, it is assumed that you are running with
PSSP software prior to 3.1. In this case, the IBM poe command sets up the high speed
switch directly and PBS interfaces with the IBM Resource (Job) Manager to track which
nodes jobs are using. PBS requires two libraries, libjm_client.a and libSDR.a,
installed with the ssp.clients fileset.
If the library libswitchtbl.a is detected, it is assumed you are running with PSSP
3.1 or later software. In this case, PBS takes on the responsibility of loading the high speed
switch tables to provide node connectivity.
The PBS_HOME directory, see --set-server-home, used
by the pbs_mom located on each node, must be on local storage and must have an identical path on each node. If the directory is setup in a different path, then MOM will not be able to
initialize the SP switch correctly.
The node names provided to the Server must match the node
names shown by the st_status command. This should be the
“reliable” node name.
Regardless of the number of real processors per node, the number of virtual processors that may be declared to the Server is
limited to the number of Switch windows supported by the
PSSP software. At the present time, this is eight (8). Therefore
only eight virtual processors may be declared per node.
With PSSP 3.1, two additional items of information must be passed to the job: the switch
window id (via a file whose name is passed), and a job key which authorizes a process to
use the switch. As poe does not pass this information to the processes it creates, an under-
PBS Pro 5.2 47
Administrator Guide
handed method had to be created to present them to the job. Two new programs are compiled and installed into the bindir directory, pbspoe and pbspd.
pbspoe is a wrapper around the real poe command. pbspoe must be used by the user in
place of the real poe. pbspoe modifies the command arguments and invokes the real
poe, which is assumed to be in /usr/lpp/ppe.poe/bin. If a user specifies:
pbspoe a.out args
that command is converted to the effective command:
/usr/lpp/ppe.poe/bin/poe pbspd job_key \
winid_file a.out args -hfile $PBS_NODEFILE
PBS_NODEFILE of course contains the nodes allocated by pbs. The pbs_mom on those
nodes have loaded the switch table with the user’s uid, the job key, and a window id of
zero. pbspd places the job key into the environment as MP_PARTITION and the window
id as MP_MPI_NETWORK pbspd then exec’s a.out with the remaining arguments.
If the user specified a command file to pbspoe with -cmdfile file then pbspoe
prefixes each line of the command file with pbspd job_key and copies it into a temporary file. The temporary file is passed to poe instead of the user’s file.
pbspoe also works with /usr/lpp/ppe.poe/bin/pdbx and /usr/lpp/
ppe.poe/bin/xpdbx. This substitution is done to make the changes as transparent to
the user as possible.
Not all poe arguments or capabilities are supported. For example,
poe job steps are not supported.
For transparent usage, it is necessary that after PBS is installed that you perform these
additional steps:
Step 1
Remove IBM’s poe, pdbx, and xpdbx from /usr/bin or any
directory in the user’s normal path. Be sure to leave the commands
in /usr/lpp/ppe.poe/bin which should not be in the user’s
path, or if in the user’s path must be after
Step 2
Create a link named /usr/bin/poe pointing to{bindir}/
48 Chapter 5
Installation from Source
pbspoe. Also make links for /usr/bin/pdbx and /usr/
bin/xpdbx which point to {bindir}/pbspoe.
Step 3
Be sure that pbspd is installed in a directory in the user’s normal path on each and every node.
5.8.7 SGI Systems Running IRIX 6
If built for Irix 6.x, pbs_mom will track which processes are part of a PBS job using
POSIX session numbers. The PBS machine type (PBS_MACH) is set to irix6.
If you are compiling on an SGI system, you must have C compiler Version or later to prevent a compiler introduced
bug dealing with _MIPS_SYMBOL_PRESENT().
PBS can be built with cpuset support by setting --enable-cpuset. A cpuset names a
set of CPUs for a job. Processes spawned for a job will be restricted to this set (both cpuwise and memory-wise).
Specifically, PBS sets the following flags during cpuset creation:
See cpusetCreate(3) for more details.
The PBS machine type (PBS_MACH) is set to irix6cpuset. Note, if a Globus MOM
(pbs_mom_globus) is being built, it will always have PBS_MACH set to “irix6”.
A special job attribute ssinodes is expected to be set by the Scheduler, in order for
pbs_mom to determine the list of CPUs to assign. ssinodes refers the number of singlesystem-image nodes to be assigned to a job. Another attribute, nodemask is set by
pbs_mom to a hexadecimal string showing the nodes/CPUs assigned to a job-- 1 bit represents 1 node.
Finally, a special job attribute hpm can be used in a scheduler to take into account SGI’s
Hardware Performance Monitor (HPM). This is an attribute that allows users to take
PBS Pro 5.2 49
Administrator Guide
advantage of such software as perfex. SGI Origin2000’s only allow one global counter
at a time, so when the system is using it, users are unable to do so and vice versa. Specifying “hpm” in the job submission, specifies if it is to use the HPM counters.
The Standard Scheduler supports cpusets, as does one of the alternate schedulers:
sgi_origin_cpuset. If you wish to use this alternate scheduler, review the configuration information in the documentation for this scheduler in the following directory of the
source tree: src/scheduler.cc/samples/sgi_origin_cpuset. To enable this
scheduler, be sure to specify these configure options:
IRIX 6 supports both 32 and 64 bit objects. In prior versions, PBS
was typically built as a 32 bit object. Because of changes in structure sizes, PBS will not be able to recover any Server, queue, or job
information recorded by a PBS Server built with 32 bit objects, or
vice versa. Please read Chapter 6 “Upgrading PBS” on page 53 for
instructions on dealing with this incompatibility.
5.8.8 Cray C90, J90, and T90 Systems
On the traditional Cray systems such as the C90, PBS supports Unicos versions 8, 9 and
10. The directory for TMPDIR will default to that defined by JTMPDIR in Unicos’s /
usr/include/tmpdir.h. MOM under Unicos will create a temporary job scratch
directory. By default, this is placed in /tmp. The location can be changed via --settmpdir=DIR
5.8.9 Unicos 10 with MLS
If you are running Unicos MLS, required in Unicos 10.0 and later, the following action is
required after the system is built and installed. MOM updates ue_batchhost and
ue_batchtime in the UDB for the user. In an MLS system, MOM must have the security
capability to write the protected UDB. To grant this capability, change directory to wherever pbs_mom has been installed and type:
spset -i 16 -j daemon -k exec pbs_mom
You, the administrator, must have capabilities secadm and class 16 to issue this command.
You use the setucat and setucls commands to get to these levels if you are autho-
50 Chapter 5
Installation from Source
rized to do so. The UDB reclsfy permission bit gives a user the proper authorization to use
the spset command.
5.8.10 Cray T3E
On the Cray T3E MPP systems, PBS supports the microkernal-based Unicos/MK version
2. On this system PBS “cooperates” with the T3E Global Resource Manager (GRM) in
order to run jobs on the system. This is needed primarily since jobs on the T3E must be
run on physically contiguous processing elements (PEs). Previous discussions regarding
the changing of TMPDIR are also applicable to the Cray T3E.
5.8.11 Compiling in DCE Support
Release 5.2 of PBS Pro introduced various code additions to support PBS in a DCE environment. As far as the administrator and/or user are concerned, these additions include:
Two new option arguments to the configure script
A new option argument to client qsub
Generation of a per job "credential" (.CR) file in both mom/jobs
and server/jobs directories
Generation of a per job security context "export" file (.XP suffix) in mom/jobs.
To build for DCE support, one must have the DCE libraries and the DES encryption
library available. The latter is part of the SSI cryptography package. One possible download site is:
There are two DCE-specific PBS configure options:
--with-des - the base directory where the des crypto package is installed.
--with-dce - the base directory for the installed DCE libraries.
Currently, the credential refresh interval for the job is not determined from information in the security service's registry. It is
instead a constant value chosen by the administrator. This value
(number of seconds between refresh attempts) is set via the
MOM’s config file parameter $dce_refresh_delta. If the
parameter is not specified, the value will default to the compiled
in value of 18000 (5 hours).
PBS Pro 5.2 51
Administrator Guide
5.9 Install Options
There are four ways in which a MOM may be installed on each of the various execution
Step 1
The first method is to do a full install of PBS on each host. While
this works, it is a bit wasteful.
Step 2
The second way is to rerun configure with the following options:
--disable-server --set-sched=no
You may also choose --disable-clients but users often use
the PBS commands within a job script so you will likely want to
build the commands. You will then need to recompile and then do
an install on each execution host.
Step 3
The third way is to install just MOM (and maybe the commands) on
each system. If the system will run the same binaries as where PBS
was compiled, then as root:
cd src/resmom
make install
cd ../cmds
make install#
If the system requires recompiling, do so at the top level to recompile the libraries and then proceed as above.
Step 4
The fourth requires that the system be able to execute the existing
binaries and that the directories sbindir and bindir in which
the PBS daemons and commands were installed during the initial
full build be available on each host. These directories, unlike the
PBS_HOME directory can reside on a network file system. If the
target tree is accessible on the host, as root execute the following
commands on each execution host:
52 Chapter 5
Installation from Source
sh {target_tree}/buildutils/pbs_mkdirs [-d new_dir] mom
sh {target_tree}/buildutils/pbs_mkdirs [-d new_dir] aux
sh {target_tree}/buildutils/pbs_mkdirs [-d new_dir] default
This will build the required portion of PBS_HOME on each
host. Use the -d option if you wish to place PBS_HOME in a
different place on the node. This directory must be on local storage on the node, not on a shared file system. If you use a different path for PBS_HOME than was specified when configure
was run, you must also start pbs_mom with the corresponding
-d option so she knows where PBS_HOME is located.
If the target tree is not accessible, copy the pbs_mkdirs shell script to each execution
host and, again as root, execute it with the above operands.
Note that the initial run of the Server or any first time run after recreating the home directory must be with the -t create option. This option directs the Server to create a new
Server database. This is best done by hand.
If a database is already present, it is discarded after receiving a positive validation
response. At this point it is necessary to configure the Server. See Chapter 7 “Configuring
the Server” on page 61 for details. The create option leaves the Server in a “idle” state. In
this state the Server will not contact the Scheduler and jobs are not run, except manually
via the qrun(1B) command.
Once the Server is up and configured, it can be placed in the “active” state by setting the
Server attribute scheduling to a value of true:
# qmgr -c “set server scheduling=true”
The value of scheduling is retained across Server terminations/starts. After the Server
is configured it may be placed into service.
You will now need to configure the PBS daemons as discussed in Chapter 7, Chapter 8,
and Chapter 9.
PBS Pro 5.2 53
Administrator Guide
Chapter 6
Upgrading PBS
This chapter provides important information on upgrading from a previous version of
PBS. If you are not currently running PBS, you can safely skip this chapter at this time.
However, be sure to refer to it before preforming a future upgrade of PBS.
There are two types of PBS upgrades: an overlay upgrade (in which you simply install the
new binaries on top of the old ones) and a migration upgrade (in which you must transfer
the jobs between the old and new versions). The difference depends on if the underlying
job data structures changed between the releases.
The Release Notes will indicate whether a migration upgrade is
required or not.
6.1 Overlay Upgrade
Most new releases of PBS (especially minor versions and patch releases) will allow you to
upgrade quickly. If the Release Notes so indicate, then follow these simple steps:
Shutdown PBS
Backup the Server’s job directory
Install the new version
Restart PBS
54 Chapter 6
Upgrading PBS
You may use tar to perform the backup of the jobs directory. (This step is only precautionary, just in case something goes wrong, you will not loose the jobs in the system, and
can restore them if needed.)
# cd /usr/spool/PBS/server_priv
# tar -cf /tmp/pbs_jobs_save jobs
Follow the normal installation procedures for installing the new version. The installation
program will pick up your existing installation parameters from the /etc/pbs.conf
file, and prompt you to confirm that you wish to use them.
6.2 Migration Upgrade
A migration upgrade is more complicated, and is needed when the PBS job structure is
different between your currently installed version, and the new version.The release notes
will indicate if you need to migrate (or move) jobs from the old version to the new.
PBS allows you to run two instances of PBS on the same system, by specifying alternative
daemon directories and port numbers. When the new version is ready to be placed into service, you will probably want to move jobs from the old system to the new. The following
procedure is suggested. All Servers must be run by root. The qmgr and qmove commands should be run by a PBS administrator (likely, root is good).
Step 1
With the old PBS daemons running, disable the queues by setting each queue’s enabled attribute to false, and stop any further scheduling by setting the Server’s scheduling attribute
to false. This will prevent any new jobs from being accepted or
started by PBS.
# qmgr
Qmgr: set queue workq enabled = false
Qmgr: set server scheduling = false
Qmgr: quit
Step 2
Backup this Server’s jobs directory, /usr/spool/PBS/
server_priv/jobs -- tar may used for this.
PBS Pro 5.2 55
Administrator Guide
# cd /usr/spool/PBS/server_priv
# tar -cf /tmp/pbs_jobs_save jobs
If the job structure has changed, you will need to move the jobs from
the old system to the new. The release notes will contain a warning
if the job structure has changed or the move is required for other
You may find it useful to set the PBS environment variable
PBS_DEFAULT (as discussed in the PBS User Guide) to either the
old or new Server, with the port numbers specified, to avoid having
to type them on the command lines as described below.
To move the jobs, continue with the following steps:
Step 3
Start the new PBS Server in its new PBS_HOME (e.g. /usr/
local/PBS) directory. If the new PBS_HOME is different from
the directory when it was compiled, use the -d option to specify the
new location. Use the -t option if the Server has not been configured for the new directory. Also start with an alternative port using
the -p option. Turn off attempts to schedule with the -a option:
# pbs_server -t create -d new_home -p 13001 -a false
Remember, you will need to use the :port syntax when commanding the new Server.
Step 4
Duplicate on the new Server the current queues and Server
attributes (assuming you wish to do so). Enable each queue which
will receive jobs at the new Server.
qmgr -c “print server" > /tmp/q_config
qmgr host:13001 < /tmp/q_config
qenable workq@host:13001
qenable someq@host:13001
56 Chapter 6
Upgrading PBS
Step 5
Now list the jobs at the original Server and move a few jobs one
at a time from the old to the new Server:
# qstat
# qmove workq@host:13001 job_id
# qstat @host:13001
If all is going well, move the remaining jobs a queue at a time:
# qmove
# qstat
# qmove
# qstat
Step 6
workq@host:13001 ‘qselect -q workq‘
someq@host:13001 ‘qselect -q someq‘
At this point, all of the jobs should be under control of the new
Server and located in the new Server’s home. If the new
Server’s home is a temporary directory, shut down the new
Server with qterm and move everything to the real home as
# cp -R new_home real_home
or, if the real (new) home is already set up, do the following to
copy just the jobs from the jobs subdirectory:
# cd new_home/server_priv/jobs
# cp * real_home/server_priv/jobs
or, as a third alternative, if the real (new) PBS_HOME exists
(including the *_priv directories), you may leave the new
Server directory where it is, and update the reference to it in the
/etc/pbs.conf file.
Now you are ready to start and enable the new batch system.
You should be aware of one quirk when using qmove. If you wish to move a job from a
Server running on a test port to the Server running on the normal port (15001), you may
PBS Pro 5.2 57
Administrator Guide
attempt, unsuccessfully to use the following command:
# qmove workq@host 123.job.host:13001
However, doing so will only serve to move the job to the end of the queue it is already in.
The Server receiving the move request (e.g. the Server running on port 13001), will compare the destination Server name, host, with its own name only, not including the port.
Hence it will match and it will not send the job where you intended. To get the job to move
to the Server running on the normal port you have to specify that port in the destination:
# qmove workq@host:15001 123.job.host:13001
6.3 Alternate Test Systems
Running an alternate or test version of PBS requires a couple extra steps. In particular, the
alternate version will need a separate PBS directory structure to run from, which must be
created before attempting to start the alternate version.
If working from the standard binary distribution, you can copy your existing PBS directory tree to the new location. (Tar may be used for this.) However you will want to ensure
that you delete any job data that might have been copied to the alternate location.
If building PBS from source code, the easiest manner to create the alternate directory
structure is to rerun the configure command with the --set-server-home option set the
desired value for the alternate PBS_HOME. Next, rebuild and install PBS. (See Chapter 5
for additional information on building from source.)
58 Chapter 6
Upgrading PBS
cd existing_PBS_HOME
tar -cvf /tmp/pbs_tree.tar .
mkdir /path/to/alternate_PBS_HOME
cd /path/to/alternate_PBS_HOME
tar -xvf /tmp/pbs_tree.tar
/bin/rm server_priv/jobs/* mom_priv/jobs/*
Alternate or test copies of the various daemons may be run through the use of the command line options which set their home directory and service port. For example, the following commands would start the three daemons with a home directory of /tmp/
altpbs and four ports around 13001, the Server on 13001, MOM on 13002 and 13003,
optional MOM Globus on 13004, 13005, and the Scheduler on 13004.
# pbs_server -t create -d /tmp/altpbs -p 13001 -M 13002 \
-R 13003 -S 13004 -g 13005 -G 13006
# pbs_mom -d /tmp/altpbs -M 13002 -R 13003
# pbs_sched -d /tmp/altpbs -S 13004 -r script_file
# pbs_mom_globus -d /tmp/altpbs -M 13005 -R 13006
Note that when the Server is started with a non-standard port number (i.e. with the -p
option as shown above) the Server “name” becomes host_name.domain:port where port is
the numeric port number being used.
Jobs may now be directed to the test system by using the -q option to qsub with the
server:port syntax. Status is also obtained using the :port syntax. For example, to
submit a job to the default queue on the above test Server, request the status of the test
Server, and request the status of jobs at the test Server:
# qsub -q @host:13001 jobscript
# qstat -Bf host:13001
# qstat @host:13001
If using job dependencies on or between test systems, there are
minor problems of which you (and the users) need to be aware.
The syntax of both the dependency string and the job
host:port syntax use colons in an indistinguishable manner.
PBS Pro 5.2 59
Administrator Guide
6.4 Dependent Jobs and Test Systems
If you have users running on a test batch system using an alternative port number, -p
option to pbs_server, problems may occur with job dependency if the following
requirements are not observed:
For a test system, the job identifier in a dependency specification must include at least the
first part of the host name.
The colon in the port number specification must be escaped by a back-slash. This is true
for both the Server and current Server sections. For example:
On a shell line, the back slash itself must be escaped from the shell, so the above become:
These rules are not documented on the qsub/qalter man pages since the likelihood of the
general user community finding themselves setting up dependencies with jobs on a test
system is small and the inclusion would be generally confusing.
60 Chapter 6
Upgrading PBS
PBS Pro 5.2 61
Administrator Guide
Chapter 7
Configuring the Server
Now that PBS has been installed, the Server and MOMs can be configured and the scheduling policy selected. The next three chapters will walk you through this process.
If you installed PBS from the binary distribution, then further configuration may not be
required as the default configuration may completely meet your needs. However, you are
advised to read this chapter to determine if the default configuration is indeed complete
for you, or if any of the optional setting may apply.
7.1 Network Addresses and Ports
PBS makes use of fully qualified host names for identifying the jobs and their location. A
PBS installation is known by the host name on which the Server is running. The name
used by the daemons, or used to authenticate messages is the canonical host name. This
name is taken from the primary name field, h_name, in the structure returned by the
library call gethostbyaddr(). According to the IETF RFCs, this name must be fully
qualified and consistent for any IP address assigned to that host.
The daemons and the commands will attempt to use /etc/services to identify the
standard port numbers to use for communication. The port numbers need not be below the
magic 1024 number. The service names that should be added to /etc/services are:
62 Chapter 7
Configuring the Server
15001/tcp #
15002/tcp #
15003/tcp #
15003/udp #
15004/tcp #
15005/tcp #
15006/tcp #
15006/udp #
Server (pbs_server)
to/from Server
RM requests
RM requests
Globus RM requests
Globus RM requests
The port numbers listed are the default numbers used by this version of PBS. If you
change them, be careful to use the same numbers on all systems. Note, the name
pbs_resmon is a carry-over from early versions of PBS when there existed separate daemons for job execution (pbs_mom) and resource monitoring (pbs_resmon). The two
functions were combined into pbs_mom though the term "resmom" might be found referring to the combined functions. If the services cannot be found in /etc/services, the
PBS components will default to the above listed port numbers.
7.2 qmgr
The PBS manager command, qmgr, provides a command-line administrator interface to
the PBS Server. There are several command line options to qmgr.
-c command
Abort qmgr on any syntax errors or any requests rejected by a
Execute a single command and exit qmgr. The command must be
enclosed in quote marks, e.g. qmgr -c "print server"
Echo all commands to standard output.
No commands are executed, syntax checking only is performed.
No errors are written to standard error.
If qmgr is invoked without the -c option and standard output is connected to a terminal,
qmgr will write a prompt to standard output and read a directive from standard input.
A command is terminated by a new line character or a semicolon (";”) character. Multiple
PBS Pro 5.2 63
Administrator Guide
commands may be entered on a single line. A command may extend across lines by escaping the new line character with a back-slash (“\”). Comments begin with the “#” character
and continue to end of the line. Comments and blank lines are ignored by qmgr. The syntax of each directive is checked and the appropriate request is sent to the Server(s). A
qmgr directive takes one of the following forms:
command server [names] [attr OP value[,...]]
command queue [names] [attr OP value[,...]]
command node
[names] [attr OP value[,...]]
Where command is the sub-command to perform on a object. Commands are:
Sets the active objects. If the active objects are specified, and the
name is not given in a qmgr command the active object names
will be used.
Create a new object, applies to queues and nodes.
Destroy an existing object, applies to queues and nodes.
Prints command specific help and usage information
List the current attributes and associated values of the object.
Print all the queue and Server attributes in a format that will be
usable as input to the qmgr command.
Define or alter attribute values of the object.
Clear the value of the attributes of the object. Note, this form
does no accept an OP and value, only the attribute name.
64 Chapter 7
Configuring the Server
Other qmgr syntax definitions follow:
qmgr Variable/Syntax Description
The list of one or more names of specific objects. The name list
is in the form:
with no intervening white space. The name of an object is
declared when the object is first created. If the name is
@server, then all the object of specified type at the Server
will be effected.
Specifies the name of an attribute of the object which is to be
set or modified. The attributes of objects are described in section 2 of the PBS ERS. If the attribute is one which consists of
a set of resources, then the attribute is specified in the form:
An operation to be performed with the attribute and its value:
= Set the value of the attribute. If the attribute has an existing
value, the current value is replaced with the new value.
+= Increase the current value of the attribute by the amount in the
new value.
-= Decrease the current value of the attribute by the amount in the
new value.
The value to assign to an attribute. If value includes white
space, commas, or other special characters, such as “#”, the
value string must be inclosed in quote marks (“ ”).
The help, list and print sub-commands of qmgr can be executed by the general
user. Creating or deleting a queue requires PBS Manager privilege. Setting or unsetting
Server or queue attributes requires PBS Operator or Manager privilege.
The qmgr built-in help function, invoked using the “help” sub-command, is illustrated by
the next example.
PBS Pro 5.2 65
Administrator Guide
% qmgr
Qmgr: help
To get help on any topic, type help <topic>
Help is available on all commands and topics.
Available commands:
active, create, delete, set, unset, list, print, quit
Other topics: attributes, operators, names, and values
For example, requesting usage information on the “set” sub-command of qmgr would
produce the following output.
% qmgr
Qmgr: help set
set object [name][,name...] attribute[.resource] OP value
Objects can be "server" or "queue", "node"
The "set" command sets the value for an attribute on the specified object. If the object is "server" and name is not specified, the attribute will be set on all the servers specified
on the command line. For multiple names, use a comma separated
list with no intervening whitespace.
set server s1 max_running = 5
set server managers = root
set server managers += susan
set node n1,n2 state=down
set queue q1@s3 resources_max.mem += 5mb
set queue @s3 default_queue = batch
Here are several more examples that illustrate using the qmgr command. Full explanation
of these and other qmgr commands are given below in explanation of the specific tasks
they accomplish.
% qmgr
Qmgr: create node mars ntype=cluster
Qmgr: set node mars resources_available.ncpus=2
Qmgr: create node venus properties=”inner,moonless”
Qmgr: set node mars properties = inner
Qmgr: set node mars properties += haslife
Qmgr: delete node mars
Qmgr: d n venus
66 Chapter 7
Configuring the Server
Commands can be abbreviated to their minimum unambiguous
form (as shown in the last line in the example above).
7.3 Default Configuration
Server management consists of configuring the Server attributes, defining nodes, and
establishing queues and their attributes. The default configuration from the binary installation sets the minimum Server settings, and some recommended settings for a typical PBS
cluster. (The default Server configuration is shown below.) The subsequent sections in this
chapter list, explain, and provide the default settings for all the Server’s attributes for the
default binary installation.
% qmgr
Qmgr: print server
# Create queues and set their attributes.
# Create and define queue workq
create queue workq
set queue workq queue_type = Execution
set queue workq enabled = True
set queue workq started = True
# Set server attributes.
set server scheduling = True
set server default_queue = workq
set server log_events = 511
set server mail_from = adm
set server query_other_jobs = True
set server scheduler_iteration = 600
7.4 Server Attributes
This section explains all the available Server attributes and gives the default values for
each. Note that the possible values for the “boolean” format are any of: “TRUE”, “True”,
“true”, “Y”, “y”, “1”; “FALSE”, “False”, “false”, “N”, “n”, “0”.
The privilege required to set or change some Server attributes has changed since the previous release. Specifically, mail_from, resources_cost, and system_cost now
require Manager privilege. comment requires at least operator privilege.
PBS Pro 5.2 67
Administrator Guide
When true directs the Server to use the acl_hosts access control lists. Requires full Manager privilege to set or alter.
Format: boolean
Default value: false = disabled
Qmgr: set server acl_hosts_enable=true
List of hosts which may request services from this Server. This list
contains the fully qualified network name of the hosts. Local
requests, i.e. from the Server’s host itself, are always accepted even
if the host is not included in the list. Wildcards (“*”) may be used in
conjunction with host names and host.subdomain names.
Format: “[+|-]hostname.domain[,...]”.
Default value: all hosts
Qmgr: set server acl_hosts=*.pbspro.com
Attribute which when true directs the Server to use the Server level
acl_users access list. Requires full Manager privilege to set or
Format: boolean (see acl_group_enable).
Default value: disabled
Qmgr: set server acl_user_enable=true
List of users allowed or denied the ability to make any requests of
this Server. Requires full Manager privilege to set or alter.
Format: “[+|-]user[@host][,...]”.
Default value: all users allowed
Qmgr: set server acl_users=bob,tom@sol,sue@sol
List of superusers who may submit to and execute jobs at this
Server. If the job execution id would be zero (0), then the job owner,
root@host, must be listed in this access control list or the job is
Format: “[+|-]user[@host][,...]”.
Default value: no root jobs allowed
Qmgr: set server acl_roots=host
A text string which may be set by the scheduler or other privileged
client to provide information to PBS users.
Format: any string.
Default value: none
Qmgr: set server comment=”Planets Cluster”
A node specification to use if there is no other supplied specification. The default value allows jobs to share a single node.
Format: a node specification string.
Default value: 1#shared
Qmgr: set server default_node=”1#shared”
68 Chapter 7
Configuring the Server
The queue which is the target queue when a request does not
specify a queue name.
Format: a queue name.
Default value: none, must be set to an existing queue
Qmgr: set server default_queue=workq
Attribute which directs the Server to automatically grant authorization for a job to be run under the user name of the user who
submitted the job even if the job was submitted from a different
host. If not set true, then the Server will check the authorization of the job owner to run under that name if not submitted
from the Server's host. See section 11.7.4 “User Authorization”
on page 151.
Format: boolean
Default value: False
Qmgr: set server flatuid=True
A bit string which specifies the type of events which are logged,
(see also section 11.13 “Use and Maintenance of Logfiles” on
page 158).
Format: integer.
Default value: 511, all events
Qmgr: set server log_events=255
The uid from which Server generated mail is sent to users.
Format: integer uid
Default value: 0 for root
Qmgr: set server mail_uid=1264
List of users granted PBS Manager privileges.
The host, sub-domain, or domain name may be wild carded by
the use of an * character. Requires Manager privilege to set or
Format: “user@host.sub.domain[,user@host.sub.domain...]” .
Default value: root on the local host
Qmgr: set server managers+=boss@sol.pbspro.com
The maximum number of jobs allowed to be selected for execution at any given time. Advisory to the Scheduler, not enforced
by the Server.
Format: integer.
Default value: none
Qmgr: set server max_running=24
The maximum number of jobs owned by any users in a single
group that are allowed to be running from this queue at one
time. This attribute is advisory to the Scheduler, it is not
enforced by the Server.
PBS Pro 5.2 69
Administrator Guide
Format: integer
Default value: none
Qmgr: set server max_group_run=16
The maximum number of jobs owned by a single user that are
allowed to be running from this queue at one time. This attribute is
advisory to the Scheduler, it is not enforced by the Server.
Format: integer
Default value: none
Qmgr: set server max_user_run=6
The maximum amount of resource RES that any single user may
consume. RES can be any valid PBS resource, such as “ncpus”,
“mem”, “pmem”, etc. This limit can be specified as both a hard and
soft limit. Most limits under PBS are hard limits (i.e. they cannot be
exceeded by the job). However, a soft limit is a limit which can be
exceeded, if nothing else is queued.
Format: resource specific
Default value: none
Qmgr: set server max_user_res.ncpus=3
Qmgr: set server max_user_res_soft.ncpus=6
The first line in the example above sets a normal (e.g. hard) limit of
3 CPUs as a maximum that any single user may consume. The second line in the example illustrates setting a soft limit of 6 CPUs on
the same resource.
Controls how multiple processor nodes are allocated to jobs. If this
attribute is set to true, jobs will be assigned to the multiple processor
nodes with the fewest free processors. This packs jobs into the fewest possible nodes leaving multiple processor nodes free for jobs
which need many processors on a node. If set to false, jobs will be
scattered across nodes reducing conflicts over memory between
jobs. If unset, the jobs are packed on nodes in the order that the
nodes are declared to the Server (in the nodes file).
Format: boolean
Default value: unset (assigns nodes in order declared)
Qmgr: set server node_pack=true
List of users granted batch operator privileges.
Format of the list is identical with managers above. Requires full
Manager privilege to set or alter.
Default value: root on the local host.
Qmgr: set server operators=sue,bob,joe,tom
The setting of this attribute controls whether or not general users,
other than the job owner, are allowed to query the status of or select
70 Chapter 7
Configuring the Server
the job. Requires Manager privilege to set or alter (see
Format: boolean
Default value: false (users may not query or select jobs owned
by other users.)
Qmgr: set server query_other_jobs=true
The list of resources and amounts available to jobs run by this
Server. The sum of the resources of each type used by all jobs
running by this Server cannot exceed the total amount listed
here. Advisory to the Scheduler, not enforced by the Server.
Format: “resources_available.resource_name=value[,...]”.
Qmgr: set server resources_available.ncpus=16
Qmgr: set server resources_available.mem=400mb
The cost factors of various types of resources. These values are
used in determining the order of releasing members of synchronous job sets. For the most part, these values are purely arbitrary and have meaning only in the relative values between
systems. The cost of the resources requested by a job is the sum
of the products of the various resources_cost values and the
amount of each resource requested by the job. It is not necessary to assign a cost for each possible resource, only those
which the site wishes to be considered in synchronous job
Format: “resources_cost.resource_name=value[,...]”
Default value: none (cost of resource is not computed)
Qmgr: set server resources_cost.mem=100
The list of default resource values that are set as limits for a job
executing on this Server when the job does not specify a limit,
and there is no queue default.
Format: “resources_default.resource_name=value[,...]
Default value: no limit
Qmgr: set server resources_default.mem=8mb
Qmgr: set server resources_default.ncpus=1
The maximum amount of each resource which can be requested
by a single job executing on this Server if there is not a
resources_max valued defined for the queue in which the job
Format: “resources_max.resource_name=value[,...]
Default value: infinite usage
Qmgr: set server resources_max.mem=1gb
Qmgr: set server resources_max.ncpus=32
The time, in seconds, between iterations of attempts by the
Server to schedule jobs. On each iteration, the scheduler exam-
PBS Pro 5.2 71
Administrator Guide
ines the available resources and runnable jobs to see if a job can be
initiated. This examination also occurs whenever a running job terminates or a new job is placed in the queued state in an execution
Format: integer seconds
Default value: 10 minutes
Qmgr: set server scheduler_iteration=300
Controls if the Server will request job scheduling by the PBS
Scheduler. If true, the scheduler will be called as required; if false,
the Scheduler will not be called and no job will be placed into execution unless the Server is directed to do so by a PBS operator or
Manager. Setting or resetting this attribute to true results in an
immediate call to the Scheduler.
Format: boolean (see acl_host_enable)
Default value: value of -a option when Server is invoked, if -a is
not specified, the value is recovered from the prior Server run. If it
has never been set, the value is “false”.
Qmgr: set server scheduling=true
An arbitrary value factored into the resource cost of any job managed by this Server for the purpose of selecting which member of a
synchronous set is released first.
Default value: none, cost of resource is not computed
Qmgr: set server system_cost=7
The following attributes are read-only: they are maintained by the Server and cannot be
changed by a client.
Shows the number of floating licenses currently available.
The release version number of the Server.
The total amount of certain resources allocated to running jobs.
The name of the Server, which is the same as the host name. If the
Server is listening to a non-standard port, the port number is
appended, with a colon, to the host name. For example:
The total number of jobs managed by the Server currently in each
The current state of the Server. Possible values are:
72 Chapter 7
Configuring the Server
The Server is running and will invoke the Scheduler as
required to schedule jobs for execution.
The Server is running but will not invoke the Scheduler
The Server is running and there is an outstanding request
to the job scheduler
The Server is terminating. No additional jobs will be
The Server is terminating in delayed mode. The Server
will not run any new jobs and will shutdown when the last
currently running job completes.
The total number of jobs currently managed by the Server.
7.5 Queue Attributes
Once you have the Server attributes set the way you want them, you will next want to
review the queue attributes. The default (binary) installation creates one queue with the
required attributes, as shown in the example below.
You may wish to change these settings or add other attributes or add additional queues.
The following discussion will be useful in modifying the PBS queue configuration to best
meet your specific needs.
% qmgr
Qmgr: print queue work
# Create and define queue workq
create queue workq
set queue workq queue_type = Execution
set queue workq enabled = True
set queue workq started = True
PBS Pro 5.2 73
Administrator Guide
There are two types of queues defined by PBS: routing and execution. A routing queue is
a queue used to move jobs to other queues including those which exist on different PBS
Servers. Routing queues are similar to the old NQS pipe queues. A job must reside in an
execution queue to be eligible to run. The job remains in the execution queue during the
time it is running. In spite of the name, jobs in a queue need not be processed in queueorder (first-come first-served or FIFO). A Server may have multiple queues of either or
both types, but there must be at least one queue defined. Typically it will be an execution
queue; jobs cannot be executed while residing in a routing queue.
Queue attributes fall into three groups: those which are applicable to both types of queues,
those applicable only to execution queues, and those applicable only to routing queues. If
an “execution queue only” attribute is set for a routing queue, or vice versa, it is simply
ignored by the system. However, as this situation might indicate the administrator made a
mistake, the Server will issue a warning message about the conflict. The same message
will be issued if the queue type is changed and there are attributes that do not apply to the
new type.
Queue public attributes are alterable on request by a client. The client must be acting for a
user with Manager or Operator privilege. Certain attributes require the user to have full
administrator privilege before they can be modified. The following attributes apply to both
queue types:
Attribute which when true directs the Server to use the queue’s
group access control list acl_groups.
Default value: false = disabled
Qmgr: set queue QNAME acl_group_enable=true
List which allows or denies enqueuing of jobs owned by members
of the listed groups. The groups in the list are groups on the Server
host, not submitting host.
Format: “[+|-]group_name[,...]”
Default value: all groups allowed
Qmgr: set queue QNAME acl_groups=math,physics
Attribute which when true directs the Server to use the acl_hosts
access list.
Format: boolean
Default value: disabled
Qmgr: set queue QNAME acl_host_enable=true
74 Chapter 7
Configuring the Server
List of hosts which may enqueue jobs in the queue.
Format: “[+|-]hostname[...]”
Default value: all hosts allowed
Qmgr: set queue QNAME acl_hosts=sol,star
Attribute which when true directs the Server to use the
acl_users access list for this queue.
Format: boolean (see acl_group_enable);
Default value: disabled
Qmgr: set queue QNAME acl_user_enable=true
List of users allowed or denied the ability to enqueue jobs in
this queue.
Format: “[+|-]user[@host][,...]”
Default value: all users allowed
Qmgr: set queue QNAME acl_users=sue,bob@star
Queue will or will not accept new jobs. When false the queue is
disabled and will not accept jobs.
Format: boolean
Default value: disabled
Qmgr: set queue QNAME enabled=true
When true, this queue will accept jobs only when being routed
by the Server from a local routing queue. This is used to force
user to submit jobs into a routing queue used to distribute jobs
to other queues based on job resource limits.
Default value: disabled
Qmgr: set queue QNAME from_route_only=true
The maximum number of jobs allowed to reside in the queue at
any given time.
Default value: infinite
Qmgr: set queue QNAME max_queuable=200
The maximum number of jobs allowed to be selected from this
queue for routing or execution at any given time. For a routing
queue, this is enforced by the Server, if set.
Qmgr: set queue QNAME max_running=16
The maximum amount of resource RES that any single user
may consume. RES can be any valid PBS resource, such as
“ncpus”, “mem”, “pmem”, etc. This limit can be both hard and
soft. (See “max_user_res.RES” on page 69 for discussion of
PBS Pro 5.2 75
Administrator Guide
hard vs. soft limits.)
Format: resource specific
Default value: none
Qmgr: set queue QNAME max_user_res.ncpus=3
Qmgr: set queue QNAME max_user_res_soft.ncpus=6
The priority of this queue against other queues of the same type on
this Server. May affect job selection for execution/routing.
Qmgr: set queue QNAME priority=123
The type of the queue: execution or route. This attribute must be
explicitly set.
Format: “execution”, “e”, “route”, “r”.
Qmgr: set queue QNAME queue_type=route
Qmgr: set queue QNAME queue_type=execution
The maximum amount of each resource which can be requested by
a single job in this queue. The queue value supersedes any Server
wide maximum limit.
Qmgr: set queue QNAME resources_max.mem=2gb
Qmgr: set queue QNAME resources_max.ncpus=32
The minimum amount of each resource which can be requested by a
single job in this queue.
Qmgr: set queue QNAME resources_min.mem=1b
Qmgr: set queue QNAME resources_min.ncpus=1
The list of default resource values which are set as limits for a job
residing in this queue and for which the job did not specify a limit.
If not set, the default limit for a job is determined by the first of the
following attributes which is set: Server’s resources_default,
queue’s resources_max, Server’s resources_max. An unset
resource is viewed as unlimited.
Format: “resources_default.resource_name=value”
Default value: none
Qmgr: set queue QNAME resources_default.mem=1b
Qmgr: set queue QNAME resources_default.ncpus=1
Jobs may be scheduled for execution from this queue. When false,
the queue is considered stopped.
Qmgr: set queue QNAME started=true
76 Chapter 7
Configuring the Server
The following attributes apply only to execution queues:
Specifies the minimum interval of cpu time, in minutes, which
is allowed between checkpoints of a job. If a user specifies a
time less than this value, this value is used instead.
Qmgr: set queue QNAME checkpoint_min=5
The amount of the time delay between the sending of SIGTERM and SIGKILL when a qdel command is issued against
a running job.
Format: integer seconds
Default value: 2 seconds
Qmgr: set queue QNAME kill_delay=5
If true, indicates that the queue has nodes associated with it.
Format: boolean
The maximum number of jobs owned by a single user that are
allowed to be running from this queue at one time.
Qmgr: set queue QNAME max_user_run=5
The maximum number of jobs owned by any users in a single
group that are allowed to be running from this queue at one
Qmgr: set queue QNAME max_group_run=20
The list of resource and amounts available to jobs running in
this queue. The sum of the resource of each type used by all
jobs running from this queue cannot exceed the total amount
listed here.
Qmgr: set queue QNAME resources_available.mem=1gb
The following attributes apply only to route queues:
If true, a site-supplied alternative job router function is used to
determine the destination for routing jobs from this queue. Otherwise, the default, round-robin router is used.
Qmgr: set queue QNAME alt_router= true
The list of destinations to which jobs may be routed.
Default value: none, should be set to at least one destination.
Qmgr: set queue QNAME route_destinations=QueueTwo
PBS Pro 5.2 77
Administrator Guide
If true, jobs with a hold type set may be routed from this queue. If
false, held jobs are not to be routed.
Qmgr: set queue QNAME route_held_jobs=true
The maximum time a job is allowed to exist in a routing queue. If
the job cannot be routed in this amount of time, the job is aborted. If
unset or set to a value of zero (0), the lifetime is infinite.
Format: integer seconds
Default infinite
Qmgr: set queue QNAME route_lifetime=600
Time delay between route retries. Typically used when the network
between servers is down.
Format: integer seconds
Default value: PBS_NET_RETRY_TIME (30 seconds)
Qmgr: set queue QNAME route_retry_time=120
If true, jobs with a future execution_time attribute may be
routed from this queue. If false, they are not to be routed.
Qmgr: set queue QNAME route_waiting_jobs=true
The following data items are read-only attributes of the queue. They are visible to client
commands, but cannot be changed by them.
The number of jobs currently residing in the queue.
Total number of jobs currently residing in the queue in each state.
The total amount of certain types of resources allocated to jobs running from this queue.
Note, an unset resource limit for a job is treated as an infinite limit.
The privilege required to set or change some queue attributes has
alt_router now require Manager privilege.
78 Chapter 7
Configuring the Server
7.6 Nodes
Where jobs will be run is determined by an interaction between the Scheduler and the
Server. This interaction is affected by the contents of the PBS nodes file, and the system
configuration onto which you are deploying PBS. Without this list of nodes, the Server
will not establish a communication stream with the MOM(s) and MOM will be unable to
report information about running jobs or notify the Server when jobs complete.
If the PBS configuration consists of a single timeshared host on which the Server and
MOM are running, all the jobs will run there. The Scheduler only needs to specify which
job it wants run.
If you are running a timeshared complex with one or more execution hosts, where MOM
is on a different host than the Server, then distributing jobs across the various hosts is a
matter of the Scheduler determining on which host to place a selected job.
If your cluster is made up of cluster nodes and you are running distributed (multi-node)
jobs, as well as serial jobs, the Scheduler typically uses the Query Resource or Avail
request to the Server for each queued job under consideration. The Scheduler then selects
one of the jobs that the Server replied could run, and directs that the job should be run. The
Server will then allocate one or more virtual processors on one or more nodes as required
to the job.
By setting the Server’s default_node specification to one temporarily-shared node
(e.g. 1#shared) jobs which do not request nodes will be placed together on a few temporarily-shared nodes.
If your system contains both cluster nodes and one timeshared node, the situation is like
the above, except you may wish to change the value of default_node to be that of the
timeshared host. Jobs that do not ask for nodes will end up running on the timeshared host.
If you have a configuration supporting both cluster nodes and multiple time shared hosts,
you have a complex system. The Scheduler must recognize which jobs request nodes and
use the Avail request to the Server. It must also recognize which jobs are to be balanced
among the timeshared hosts, and provide the host name to the Server when directing that
the job be run. The Standard scheduler does this.
Regardless of node type, each node must be defined in the
Server’s nodes file, /usr/spool/PBS/server_priv/
nodes. Time-shared nodes have :ts appended to their node
name. Cluster nodes have no name suffix.
PBS Pro 5.2 79
Administrator Guide
In PBS, allocation of cluster nodes (actually the allocation of virtual processors, VPs, of
the nodes) to a job is handled by the Server. Each node must have its own copy of MOM
running on it. If only timeshared hosts are to be served by the PBS batch system, the Job
Scheduler must direct where the job should be run. If unspecified, the Server will execute
the job on the host where it is running.
7.6.1 PBS Nodes File
A basic nodes file is created for you by the install procedure. This file contains only the
name of the host from which the install was run and set as a time-shared host. If you have
more than one host in your PBS cluster or you are not planning on running jobs on the
Server’s host, you need to edit the list of nodes to reflect your site.
You may edit the nodes list in one of two ways. If the Server is not running, you may
directly edit the nodes file with a text editor. If the Server is running, you should use
qmgr to edit the list of nodes.
The node list is defined to the Server in the file /usr/spool/PBS/server_priv/
nodes. This is a simple text file with the specification of a single node per line in the file.
The format of each line in the file is:
node_name[:ts] [attributes]
The node name is the network name of the node (host name), it does not have to be fully
qualified (in fact it is best if it is as short as possible). The optional :ts appended to the
name indicates that the node is a timeshared node.
Nodes can have attributes associated with them. Attributes come in three types: properties,
name=value pairs, and name.resource=value pairs.
Zero or more properties may be specified. The property is nothing more than a string of
alphanumeric characters (first character must be alphabetic) without meaning to PBS.
Properties are used to group classes of nodes for allocation to a series of jobs.
Any legal node name=value pair may be specified in the node file in the same format as on
a qsub directive: attribute.resource=value. For example:
NodeA resource_available.ncpus=3 max_running=1
80 Chapter 7
Configuring the Server
resources_available.ncpus=NUMBER, which can be added to declare the number of virtual processors (VPs) on the node. NUMBER is a numeric string, for example
np=4. This expression will allow the node to be allocated up to NUMBER times to one
job or more than one job. If np=NUMBER is not specified for a cluster node, it is assumed
to have one VP.
Note that if these values are not explicitly set, they will take the
value provided by MOM. But if they are explicitly set, that set
value will be carried forth even across Server restarts.
These include:
Each item on the line must be separated by white space. The items may be listed in any
order, except that the host name must always be first. Comment lines may be included if
the first non-white space character is the pound sign ’#’.
The following is an example of a possible nodes file for a cluster called “planets”:
# The first set of nodes are cluster nodes.
# Note that the properties are provided to
# logically group certain nodes together.
# The last node is a timeshared node.
inner moonless
inner moonless np=1
inner np=1
inner np=2
outer np=18
outer np=16
outer np=14
outer np=12
PBS Pro 5.2 81
Administrator Guide
7.6.2 Creating or Adding nodes:
After pbs_server is started, the node list may be entered or altered via the qmgr command:
create node node_name [attribute=value]
where the attributes and their associated possible values are shown in the table below.
The busy state is set by the execution daemon, pbs_mom, when a load-average threshold
is reached on the node. See max_load in MOM’s config file (“Static Resources” on
page 105). The job-exclusive and job-sharing states are set when jobs are running on the node.
All comma separated strings must be enclosed in quotes.
Below are several examples of setting node attributes via qmgr.
% qmgr
Qmgr: create node mars np=2,ntype=cluster
Qmgr: create node venus properties=”inner,moonless”
Modify nodes:
Once a node has been created, its attributes and/or properties can be
modified using the following qmgr syntax:
set node node_name [attribute[+|-]=value]
where attributes are the same as for create. For example:
% qmgr
Qmgr: set node mars properties=inner
Qmgr: set node mars properties+=haslife
Delete nodes:
Nodes can be deleted via qmgr as well, using the delete node
syntax, as the following example shows:
% qmgr
Qmgr: delete node mars
Qmgr: delete node pluto
82 Chapter 7
Configuring the Server
7.7 Node Attributes
A node has the following public attributes:
The state of the node, one of: free, down, offline
Format: string
Qmgr: set node MyNode state=offline
Any alphanumeric string or comma separated set of strings,
starting with an alphabetic character.
Format: string
Qmgr: set node MyNode properties=”red,blue”
The type of the node, one of : cluster, time-shared
Format: string
Qmgr: set node MyNode ntype=cluster
List of resources available on node.
Format: resource list
Abbreviation for resources_available.ncpus. A number of virtual processors greater than zero.
Format: integer > 0
Qmgr: set node MyNode np=12
List of resources in use on node.
Format: resource list
Maximum number of running jobs; advisory to scheduler.
Format: integer
Qmgr: set node MyNode max_running=22
Maximum number of running jobs per user; advisory.
Format: integer
Qmgr: set node MyNode max_user_run=4
Maximum number of running jobs per group; advisory.
Format: integer
Qmgr: set node MyNode max_group_run=8
PBS Pro 5.2 83
Administrator Guide
Name of an execution queue (if any) associated with the node. Only
jobs from the named queue will be run on associated node.
Format: queue specification
Qmgr: set node MyNode queue=MyQueue
List of reservations pending on the node; read-only.
Format: reservation specification
General comment, e.g. the reason the node is marked down or offline; can be set by Manager or Operator.
Format: string
Qmgr: set node MyNode comment=”Down until 5pm”
A node has the following read-only attributes:
Shows the number of physical CPUs on the node, which determine
the number of licenses required for that node.
Indicates the node "license state" as a single character, according to
the following table:
licensed with a node lock or fixed license
licensed with a floating license
7.7.1 Setting Node Limits
It is possible to set limits on queues (and the Server) as to how many nodes a job can
request. The nodes resource itself is a text string and difficult to limit. However, two
additional Read-Only resources exist for jobs. They are nodect and neednodes.
Nodect (node count) is set by the Server to the integer number of nodes desired by the
user as declared in the “nodes” resource specification. That declaration is parsed and the
resulting total number of nodes is set in nodect. This is useful when an administrator
wishes to place an integer limit, resources_min or resources_max on the number
of nodes used by a job entering a queue.
Based on the earlier example of declaring nodes, if a user requested a nodes specification
of: 3:inner+2:outer, then nodect would get set to 5 (i.e. 3+2). Neednodes is initially set by the Server to the same value as nodes. Neednodes may be modified by the
84 Chapter 7
Configuring the Server
job Scheduler for special policies. The contents of neednodes determines which nodes
are actually assigned to the job. Neednodes is visible to the Manager but not to an
unprivileged user.
If you wish to set up a queue default value for “nodes” (a value to which the resource is
set if the user does not supply one), corresponding default values must be set for
“nodect” and “neednodes”. For example:
% qmgr
Qmgr: set queue small resources_default.nodes=1:inner
Qmgr: set queue small resources_default.nodect=1
Qmgr: set queue small resources_default.neednodes=1:inner
Minimum and maximum limits are set for “nodect” only. For example:
% qmgr
Qmgr: set queue small resources_min.nodect=1
Qmgr: set queue small resources_max.nodect=15
Minimum and maximum values must not be set for either
nodes or neednodes as their value are strings.
7.7.2 Nodes Specification Information
This section provides additional information about working with the PBS nodes file and
nodes specification.
Step 1
If a single specific host is named in the Run Job request and the
host is specified in the nodes file as a timeshared host, the
Server will attempt to run the job on that host.
Step 2
If either:
(a) a specific host is named in the Run Job and the named node
does not appear in the Server’s nodes file as a timeshared host;
(b) a “+” separated list of hosts [or node properties] is specified
in the Run Job request;
then, the Server attempts to allocate one (or more as requested)
virtual processor on the named cluster node(s)named in the job.
PBS Pro 5.2 85
Administrator Guide
All of the named nodes have to appear in the Server’s nodes
file. If the allocation succeeds, the job [shell script] is run on the
first of the nodes allocated.
Step 3
If no location was specified on the Run Job request, but the job
requests nodes, then the required number of virtual processors
on cluster nodes which match the request are allocated if possible. If the allocation succeeds, the job is run on the node allocated to match the first specification in the node request. Note,
the Scheduler may modify the job’s original node request, see
the job attribute neednodes
For SMP nodes, where multiple virtual processors have been
declared, the order of allocation of processors is controlled by
the setting of the Server attribute node_pack
If set true, VPs will first be taken from nodes with the fewest
free VPs. This packs jobs into the fewest possible nodes, leaving nodes available with many VPs for those jobs that need
many VPs on a node.
If node_pack is set false, VPs are allocated from nodes with
the most free VPs. This scatters jobs across the nodes to minimize conflict between jobs. If node_pack is not set to either
true or false, i.e. unset then the VPs are allocated in the order
that the nodes are declared in the Server’s nodes file.
Be aware that if node_pack is set, the internal order of nodes
is changed. If node_pack is later unset, the order will no
longer be changed, but it will not be in the order originally
established in the nodes file.
Step 4
If the Server attribute default_node is set, its value is used.
If this matches the name of a time-shared node, the job is run on
that node. If the value of default_node can be mapped to a
set of one or more free cluster nodes, they are allocated to the
Step 5
If default_node is not set, and at least one time-shared
node is defined, that node is used. If more than one is defined,
the first is selected for the job.
86 Chapter 7
Configuring the Server
Step 6
The last choice is to act as if the job has requested 1#shared.
The job will have allocated to it an existing job-shared VP, or if
none exists, then a free VP is allocated as job-shared.
The exec_host string and the runjob destination string is now of the form:
where P is the process index ranging from 0 to P-1, the number of requested processes on
the node; and C is the number of CPUs per process. For example, a request of
-l nodes=alpha:ppn=2:ncpus=2+beta
would result in a execution host string of
7.7.3 Node Comments
Nodes have a "comment" attribute which can be used to display information about that
node. If the comment attribute has not be explicitly set by the PBS Manager and the node
is down, it will be used by the PBS Server to display the reason the node was marked
down. If the Manager has explicitly set the attribute, the Server will not overwrite the
comment. The comment attribute may be set via the qmgr command:
% qmgr
Qmgr: set node pluto comment=”node will be up at 5pm”
SGI Weightless CPU Support
Submitting a job and requesting -l ncpus=0 is now legal. In an non-cpuset SGI Irix 6.x
environment, the job's kernel scheduling priority will be set "weightless". There will no
allocation at the Server, Queue, or Node level of CPUs; i.e.
resources_assigned.ncpus will not be incremented for this job.
Because ncpus=0 has no useful effect on any other system
and can result in allowing too many jobs to be run, it is strongly
recommended that jobs not be allowed to be submitted with
ncpus=0. This may be done by setting a Server level resource
PBS Pro 5.2 87
Administrator Guide
default and a resources minimum via the qmgr command:
set server resources_default.ncpus=1
set queue q1 resources_min.ncpus=1
set queue q2 resources_min.cnpus=1
7.9 Job Attributes
Tabular listing of attributes of a PBS job are given in the PBS User Guide under the heading “Job Attributes”.
7.10 PBS Resources
PBS has a standard set of "resources" which may be specified as a job requirement. Common examples of the predefined standard resources are:
amount of CPU time
amount of real memory
number of CPUs
number and type of execution nodes
amount of real clock time
Complete listing of available PBS resources is given in Chapter
4 of the PBS User Guide.
Depending on site policy, the required resources may be considered against the availability of the resources to determine ordering of jobs for execution and placement of jobs on
an execution host.
7.10.1 Defining New Resources
It is possible for the PBS Manager to define new resources within PBS. Once created, jobs
may request these new resources and the Scheduler can be directed to consider the new
resources in the scheduling policy. (See section “Dynamic Consumable Resources” on
page 126 for instructions on how to configure the Scheduler to use the new resources you
create.) To define one or more new resources, the Administrator creates a file,
88 Chapter 7
Configuring the Server
(PBS_HOME)/server_priv/resourcedef. Each line in the file defines a
resource. The format of each line is:
RESOURCE_NAME is any string made up of alphanumeric characters, starting with a
alphabetic character. The underscore character, “_”, and the hyphen, “-”, are also allowed.
RTYPE is the type of the resource value, one of the following key words:
the value is a long integer
the value is a floating point number
the value is a integer number following by a suffix denoting
magnitude k, m, g, t and b for bytes or w for words.
a null terminated string
If not specified, the resource will default to type long.
FLAGS is a set of characters which indicate if the Server should accumulate the requested
amounts of the resource in the attribute resources_assigned when the job is run.
The value of flag is the concatenation of one or more of the following letters:
the amount is tracked at the Queue and Server level
the amount is tracked at the Node level, for all nodes assigned
to the job
the amount is tracked at the Node level for only the first node
allocated to the job
If not specified, the resource will not be accumulated in resources_assigned. For
example, if the Administrator created the following lines in /usr/spool/pbs/
A user may specify any of these resources on job submission, as the following example
PBS Pro 5.2 89
Administrator Guide
% qsub -l kolas=4,pandas=10gb,wombat=brown \
-l kiwi=3kb -lnodes=2 script
If the job resides in the execution queue "workq" and is executing on nodes NodeA and
NodeB, then
queue "workq" would show:
node NodeA, the first node allocated, would show:
node NodeB would show:
7.10.2 Resource Min/Max Attributes
Minimum and maximum queue and Server limits work with numeric valued resources,
including time and size values. Generally, they do not work with string valued resources
because of character comparison order. However, setting the min and max to the same
value to force an exact match will work even for string valued resources.
% qmgr
Qmgr: set queue big resources_max.arch=unicos8
Qmgr: set queue big resources_min.arch=unicos8
The above example can be used to limit jobs entering queue big to those specifying
arch=unicos8. Again, remember that if arch is not specified by the job, the tests pass
automatically and the job will be accepted into the queue.
90 Chapter 7
Configuring the Server
7.11 Advanced Configuration Options
This section discusses several advanced configuration options, and provides, supplemental information for configuration of the PBS Server.
7.11.1 Selective Routing of Jobs into Queues
Often it is desirable to route jobs to various queues on a Server, or even between Servers,
based on the resource requirements of the jobs. The queue resources_min and
resources_max attributes discussed above make this selective routing possible. As an
example, let us assume you wish to establish two execution queues, one for short jobs of
less than one minute cpu time, and the other for long running jobs of one minute or longer.
Call them short and long. Apply the resources_min and resources_max
attribute as follows:
% qmgr
Qmgr: set queue short resources_max.cput=59
Qmgr: set queue long resources_min.cput=60
When a job is being enqueued, it’s requested resource list is tested against the queue limits: resources_min <= job_requirement <= resources_max. If the resource test
fails, the job is not accepted into the queue. Hence, a job asking for 20 seconds of cpu time
would be accepted into queue short but not into queue long.
Note, if the min and max limits are equal, only that exact value
will pass the test.
You may wish to set up a routing queue to direct jobs into the queues with resource limits.
For example:
% qmgr
Qmgr: create queue funnel queue_type=route
Qmgr: set queue funnel route_destinations =”short,long”
Qmgr: set server default_queue=funnel
A job will end up in either short or long depending on its cpu time request.
You should always list the destination queues in order of the most restrictive first as the
PBS Pro 5.2 91
Administrator Guide
first queue which meets the job’s requirements will be its destination (assuming that queue
is enabled). Extending the above example to three queues:
% qmgr
Qmgr: set queue short resources_max.cput=59
Qmgr: set queue long resources_min.cput=1:00
Qmgr: set queue long resources_max.cput=1:00:00
Qmgr: create queue huge queue_type=execution
Qmgr: set queue funnel route_destinations=”short,long,huge”
Qmgr: set server default_queue=funnel
A job asking for 20 minutes (20:00) of cpu time will be placed into queue long. A job
asking for 1 hour and 10 minutes (1:10:00) will end up in queue huge by default.
If a test is being made on a resource as shown with cput
above, and a job does not specify that resource item (it does not
appear in the -l resource=valuelist on the qsub command, the test will pass. In the above case, a job without a cpu
time limit will be allowed into queue short. For this reason,
together with the fact that an unset limit is considered to be an
infinite limit, you may wish to add a default value to the queues
or to the Server.
% qmgr
Qmgr: set queue short resources_default.cput=40
Qmgr: set server resources_default.cput=40
Either of these examples will ensure that a job without a cpu
time specification is limited to 40 seconds. A
resources_default attribute at a queue level only applies
to jobs in that queue.
Be aware of several important facts:
If a default value is assigned, it is done so after the tests against
min and max. Default values assigned to a job from a queue
resources_default are not carried with the job if the job
moves to another queue. Those resource limits becomes unset
92 Chapter 7
Configuring the Server
as when the job was specified. If the new queue specifies
default values, those values are assigned to the job while it is in
the new queue. Server level default values are applied if there is
no queue level default.
7.11.2 Recording Server Configuration
If you should you wish to record the configuration of a PBS Server for re-use later, you
may use the print subcommand of qmgr(8B). For example,
% qmgr -c "print server" > /tmp/server.con
will record in the file /tmp/server.con the qmgr subcommands required to recreate
the current configuration including the queues. The commands could be read back into
qmgr via standard input:
% qmgr < /tmp/server.con
Node configuration information is not printed. To save the current node configuration
information, make a copy of the server_priv/nodes file.
7.11.3 Server Support for Globus
If Globus support is enabled, then an entry must be made in the PBS node file with :gl
appended to the name. This is the only case in which two nodes may be defined with the
same node name. One may be a Globus node (MOM), and the other a non-Globus node.
PBS Pro 5.2 93
Administrator Guide
Chapter 8
Configuring MOM
The execution server daemons, MOMs, require much less configuration than does the
Server. The installation process creates a basic MOM configuration file which contains the
minimum entries necessary in order to run PBS jobs. This chapter describes the MOM
configuration file, and explains all the options available to customize the PBS installation
to your site.
8.1 MOM Config File
The behavior of MOM is controlled via a configuration file which is read upon daemon
initialization (start-up) and upon re-initialization (when pbs_mom receives a SIGHUP
If the -c option is not specified when MOM is started, she will open /usr/spool/
PBS/mom_priv/config if it exists. If it does not, MOM will continue anyway. This
file may be placed elsewhere or given a different name, in which case pbs_mom must be
started with the -c option with the new file name and path specified.
The configuration file provides several types of run time information to MOM: access
control, static resource names and values, external resources provided by a program to be
run on request via a shell escape, and values to pass to internal functions at initialization
(and re-initialization).
94 Chapter 8
Configuring MOM
Each configuration entry is on a single line with the component parts separated by white
space. If the line starts with a pound sign (“#”), the line is considered to be a comment and
is ignored.
The installation process creates a MOM configuration file with the following entries,
which are explained in detail in the subsequent sections of this chapter.
$logevent 0x1ff
$clienthost server-hostname
8.1.1 MOM Initialization Values
An initialization value directive has a name which starts with a dollar sign (“$”) and must
be known to MOM via an internal table. Currently the permitted entries in this table are:
On cpuset-enabled SGI systems, requests to allocate nodes
close together (1) or anywhere (0, the default).
alloc_nodes_greedy 1
If present, causes PBS to pass a special upgrade checkpoint flag
to the SGI IRIX checkpoint system for use immediately prior to
an Irix operating system upgrade. For details on use, see
“Checkpointing Jobs Prior to SGI IRIX Upgrade” on page 149.
Causes a host name to be added to the list of hosts which will be
allowed to connect to MOM. Two host names are always
allowed to connect to MOM: “localhost” and the name returned
by the system call gethostname(). These names need not be
specified in the configuration file.
The Server’s host must be either the same as MOM or be listed
as a clienthost entry in each MOM’s config file. Upon
startup, MOM will send a restart notice to the Server.
The IP addresses of all the hosts (nodes) in the Server nodes
file will be forwarded by the Server to the MOM on each host
listed in the nodes file. These hosts need not be in the various
MOM’s configuration file as they will be added internally when
PBS Pro 5.2 95
Administrator Guide
the list is received from the Server.
The hosts which are provided by the Server to MOM comprise a sisterhood of hosts. Any one of the sisterhood will accept connections
from a Scheduler [Resource Monitor (RM) requests] or Server [jobs
to execute] from within the sisterhood. They will also accept Internal MOM (IM) messages from within the sisterhood. For a sisterhood to be able to communicate IM messages to each other, they
must all share the same RM port. For example, here are two lines
for the configuration file which will allow the hosts “phobos” and
“deimos” to connect to MOM:
$clienthost phobos
$clienthost deimos
Sets a factor used to adjust cpu time used by a job. This is provided
to allow adjustment of time charged and limits enforced where the
job might run on systems with different cpu performance. If MOM’s
system is faster than the reference system, set $cputmult to a
decimal value greater than 1.0. If MOM’s system is slower, set
$cputmult to a value between 1.0 and 0.0. The value is given by
value = speed_of_this_system / speed_of_reference_system
For example:
$cputmult 1.5
$cputmult 0.75
cpuset_create_flags arg
On cpuset-enabled SGI systems, defines whether to allocate either
memory or CPUs in an exclusive fashion.
cpuset_create_flags CPUSET_CPU_EXCLUSIVE
cpuset_create_flags CPUSET_MEMORY_EXCLUSIVE
cpuset_destroy_delay seconds
On cpuset-enabled SGI systems, specifies the number of seconds to
wait before tearing down (deleting) a cpuset.
96 Chapter 8
Configuring MOM
cpuset_small_mem arg
On cpuset-enabled SGI systems, disables running jobs on
shared cpusets when set to “0”.
cpuset_small_ncpus arg
On cpuset-enabled SGI systems, disables running jobs on
shared cpusets when set to “0”.
$enforce arg
Specifies site-specific resource enforcement behavior of mem or
ncpus. (See the pbs_mom manual page for details.) Arguments to the enforce directive include the following:
if present, enforce this limit; default: off
if present, enforce this limit; default: off
if present, enforce this limit; default: off
minimum walltime before enforcement; default: 120 seconds
percentage over the limit to allow;
default: 50
ncpus factor to allow; default: 1.025
if present, enforce this limit; default: off
percentage over the limit to allow;
default: 50
ncpus factor to allow; default: 1.5
weighting when average is moving up;
default: 0.4
weighting when average is moving
down; default: 0.1
Declares the low water mark for load on a node. It works in
conjunction with a $max_load directive. When the load average on the node drops below the ideal_load, MOM on that
PBS Pro 5.2 97
Administrator Guide
node will inform the Server that the node is no longer busy. For
$ideal_load 2.0
$max_load 3.5
Enables support for “idle workstation cycle harvesting” as
described later in this chapter. Details are provided on page 107.
$kdb_idle 1800 10 5
Sets the mask that determines which event types are logged by
pbs_mom. For example:
$logevent 0x1ff
$logevent 255
The first example would set the log event mask to 0x1ff (511) which
enables logging of all events including debug events. The second
example would set the mask to 0x0ff (255) which enables all events
except debug events. The values of events are listed in section 11.13
“Use and Maintenance of Logfiles” on page 158.
Declares the high water mark for load on a node. It is used in conjunction with a $ideal_load directive. When the load average
exceeds the high water mark, MOM on that node will notify the
Server that the node is busy. The state of the node will be shown as
busy. A busy cluster node will not be allocated to jobs. This is useful in preventing allocation of jobs to nodes which are busy with
interactive sessions.
A busy time-shared node may still run new jobs under the direction of the Scheduler. Both the $ideal_load and $max_load
directives add a static resource, ideal_load and max_load,
which may be queried by the Scheduler. These static resources are
supported by the Standard scheduler when load-balancing jobs.
98 Chapter 8
Configuring MOM
Specifies the number of nodes should be allocated to shared
jobs with cpuset-enabled SGI IRIX systems.
Causes a host name to be added to the list of hosts which will be
allowed to connect to MOM without needing to use a privileged
port. The means for name specification allows for wildcard
matching. Connections from the specified hosts are restricted in
that only internal queries may be made. Only static resources
from the config file will be reported and no control requests can
be issued. This is to prevent any shell commands from being
run by a non-root process.
This type of entry is typically used to specify hosts on which a
monitoring tool, such as xpbsmon, can be run. Xpbsmon will
query MOM for general resource information.
For example, here is a configuration file line which will allow
queries from any host from the domain “pbspro.com”:
$restricted *.pbspro.com
Directs MOM to use /bin/cp instead of rcp or scp for
delivery of output files. If MOM is to move a file to a host other
than her own, MOM normally uses a remote copy command
(scp or rcp) to transfer the file. This applies to stage-in/out
and delivery of the job’s standard output/error. The destination
is recorded as hostx:/full/path/name. So if hostx is
not the same system on which MOM is running, she uses scp
or rcp; if it is the same system, MOM uses /bin/cp.
However, if the destination file system is NFS mounted among
all the systems in the PBS environment (cluster), cp may work
better than scp/rcp. One or more $usecp directives in the
config file can be used to inform MOM about those file systems
where the cp command should be used instead of scp/rcp.
The $usecp entry has the form:
$usecp hostspec:path_prefix new_prefix
The hostspec is either a fully qualified host–domain name or
a wild-carded host–domain specification as used in the Server’s
host ACL attribute. The path_prefix is the leading (root)
PBS Pro 5.2 99
Administrator Guide
component of the fully qualified path for the NFS files as visible on
the specified host. The new_prefix is the initial components of
the path to the same files on MOM’s host. If different mount points
are used, the path_prefix and the new_prefix will be different. If the same mount points are used for the cross mounted file
system, then the two prefixes will be the same.
When given a file destination, MOM will:
Step 1
Match the hostspec against her host name. If they match, MOM
will use the cp command to move the file. If the hostspec is
“localhost” then MOM will also use cp.
Step 2
If the match in step one fails, MOM will match the host portion of
the destination against each $usecp hostspec in turn. If the host
matches, MOM matches the path_prefix against the initial segment of the destination name. If this matches, MOM will discard the
host name, replace the initial segment of the path that matched
against path_prefix with the new_prefix and use cp with
the resulting destination.
Step 3
If the host is neither the local host nor matches any of the $usecp
directives, MOM will use the scp or rcp command to move the
For example, a user named Beth on host phobos.pbspro.com submits a job while her current working directory is:
The destination for her output would be given by PBS as:
The job runs on node jupiter.pbspro.com which has the user’s home
file system cross mounted as /r/home/beth. Either of the following entries in the config file on node jupiter will result in a cp
copy to /r/home/beth/proj/123.OU instead of an rcp copy
to phobos.pbspro.com:/u/wk/beth/proj/123.OU
$usecp phobos.pbspro.com:/u/wk/ /r/home/
$usecp *.pbspro.com:/u/wk/ /r/home/
100 Chapter 8
Configuring MOM
Note that the destination is matched against the $usecp entries
in the order listed in the config file. The first match of host and
file prefix determines the substitution. Therefore, if you have
the same physical file system mounted as /scratch on node
mars and as /workspace on every other host, then the entries
in the config file on jupiter should be in the following order:
$usecp mars.pbspro.com:/scratch /workspace
$usecp *.pbspro.com:/workspace /workspace
Sets the time-out period in seconds for the prologue and epilogue scripts. (See discussion of the prologue and epilogue in
section 11.12 “Job Prologue/Epilogue Scripts” on page 155.)
An alarm is set to prevent the script from locking up the job if
the script hangs or takes a very long time to execute. The
default value is 30 seconds. An example:
$prologalarm 60
Sets a factor used to adjust wall time usage by a job to a common reference system. The factor is used for walltime calculations and limits in the same way as $cputmult is used for cpu
In the above listing of MOM configuration parameters, only
those that apply solely to SGI IRIX systems do not have a “$”
prepended to the name.
Job Memory Limit Enforcement
Enforcement of the "mem" (physical memory) resource usage is available on all platforms. Enforcement is configurable by a entry in MOM’s config file. By default,
enforcement is off. If a $enforce mem statement appears in the config file, then jobs
that exceed their specified amount of physical memory will be killed. There are two items
to be aware of:
"mem" is a per job/ per node limit.
"mem" enforcement is polled, therefore a job may exceed its
limit for up to two minutes before it is detected.
PBS Pro 5.2 101
Administrator Guide
SGI Non-cpuset Memory Enforcement
Under Irix 6.5.x, there are two ways to determine the amount of real memory a set of processes are using. The "simple" way, as used by the ps(1) command, looks solely at the
pr_rssize field of the /proc/pinfo/* entry for each process. The "complex"
method uses special SGI calls to determine the "shared" state of each memory segment in
each process.
The "simple" method is quick and clean. However, this method does not factor in shared
memory segments, so the resulting usage figure for processes that are started by the
sproc(2) call is too high. The shared segments are counted fully against each process.
This "apparent" over usage can result in under loading of the physical memory in the system.
The "complex" method correctly factors in the shared memory segments and yields a more
accurate report on the amount of physical memory used. However, the SGI
ioctl(PIOCMAP_SGI) call requires that the kernel look at each memory segment.
This can result in the calling program, pbs_mom, being blocked for an extended period of
time on larger systems. Systems smaller than 32 CPUs are not likely to see a problem.
Earlier versions of PBS shipped with the "simple" memory calculation compiled; the
"complex" option was only available if you recompiled from source. In PBS Pro 5.2, the
memory calculation option is run-time selectable. By default, the "simple" option is
enabled. With the addition of a $enforce complexmem statement in MOM’s config file, the "complex" memory usage calculation is selected.
If the "complex" method is selected, the administrator needs to
monitor the MOM logs for a warning of the form "time lag N secs"
where N is a number of seconds greater than five. If this message
appear frequently, it means the Irix kernel is taking that long to
respond to the ioctl call and the performance of pbs_mom may
suffer. In that case, it is recommended that the site revert to the
"simple" calculation or run the cpuset version of MOM.
Job NCPUS Limit Enforcement
Enforcement of the ncpus (number of CPUs used) is now available on all platforms.
Enforcement is configurable by a set of entries in MOM's config file. By default,
102 Chapter 8
Configuring MOM
enforcement is off since it has not been enforced in the past.
Associated with this enforcement is a new read-only resource cpupercent. This is a
report of the average percentage usage of one CPU. For example, a value of 50 means that
during a certain period, the job used 50 percent of one CPU. A value of 300 means over
the period, the job used an average of three CPUs. Enforcement is based on two separate
checks. The first check is based on the polled sum of CPU time for all processes in the job.
Each poll period, the total CPU time used, divided by the total walltime, is checked
against the value specified for ncpus * 100. If this "average" value exceeds the number
of CPUs requested and if the cpuaverage enforcement is turned on, the job is aborted.
The second check during each poll period looks for sudden bursts of CPU activity. cpupercent is a moving weighted average based on the prior cpupercent and the
amount of new CPU time used divided by the walltime for this period. This value can be
weighted to ignore or punish sudden bursts of CPU activity. This enforcement is available
if cpuburst is set in MOM’s config file.
The following parameters, set via a $enforce statement in the config file, control the
enforcement, weighting, and allowed overrun. (Types and description of each are given in
the discussion of $enforce under “MOM configuration options” on page 104 above.
For the absolute cpu time / walltime calculation, the following enforce arguments are
used: cpuaverage, average_trialperiod, average_percent_over,
average_cpufactor. Given the default values, a job will be killed if:
(cput / walltime) > ((ncpus * 100 * average_cpufactor) + average_percent_over
This enforcement only occurs after the job has had average_trialperiod seconds
of walltime.
For the weighted moving average, the following enforce arguments are used: cpuburst, delta_percent_over,
The new reported cpupercent value is determined by weighing the new cput/walltime
for the last measurement period and the old cpupercent:
new_percent = change_in_cpu_time / change_in_walltime
weight = delta_weight[up|down] * walltime/max_poll_period
new_cpupercent = (new_percent * weight) + (old_cpupercent * (1-weight))
delta_weight_up is used if the new_percent is higher than the old cpupercent
PBS Pro 5.2 103
Administrator Guide
value and delta_weight_down is used if new_percent is lower than the old value.
If delta_weight_[up|down] is 0.0, then the value for cpupercent will not change
with time. If it is 1.0, cpupercent will become the new_percent for the poll period;
that means cpupercent changes quickly. (max_poll_period is the maximum time
between samples, set to 120 seconds.) The job will be killed if
new_cpupercent > ((ncpus * 100 * delta_cpufactor) + delta_percent_over)
The following entries in MOM’s config file would turn on enforcement of both average
and burst with the default values:
delta_percent_over 50
delta_cpufactor 1.05
delta_weightup 0.4
delta_weightdown 0.1
average_percent_over 50
average_cpufactor 1.025
average_trialperiod 120
Enhanced SGI “cpusets” Support
PBS Pro version 5.2 introduced numerous enhancements for running PBS in conjunction
with SGI “cpusets”. (An IRIX “cpuset” is a named region of an SGI Origin system composed of one or more nodeboards, and associated memory and CPUs.) This section discusses these new features, and changes from the previous version’s support for “cpusets”.
8.5.1 New Job Classes for IRIX cpusets
MOM now has a concept of two classes of jobs: a small job and a multi-cpu job. The small
job, which is usually a single CPU job with memory requirements such that it will fit on a
single nodeboard, will allow itself to be run within a cpuset where other similar jobs run.
The multi-cpu jobs are those that require more resources than available on a single nodeboard or which would want to run exclusively within a cpuset for repeatability of performance. The small job runs on a shared cpuset whereas the multi-cpu job runs on an
exclusive cpuset. A special job resource, ssinodes, if set, will force any job to be allo-
104 Chapter 8
Configuring MOM
cated exclusive cpusets. Also, up to max_shared_nodes (set in MOM’s config file)
will be allowed to be assigned to shared cpusets. To find out which cpuset is assigned to a
running job, the alt_id job attribute has a field called cpuset that will show this information.
To set a threshold as to the number of nodeboards that can be assigned to shared cpusets,
set the following in MOM’s config file:
<# of nodeboards>
If you don't want MOM to run small jobs within a shared cpuset, set the following in
MOM’s config file:
cpuset_small_ncpus 0
cpuset_small_mem 0
8.5.2 MOM configuration options
In order to make MOM config file options consistent, the format of
cpuset_create_flags for specifying the flags to pass to cpusetCreate() is
now changed from
$cpuset_create_flags <flags>
cpuset_create_flags <flags>
Similarly, the format for cpuset_destroy_delay for setting the number of seconds
to sleep before tearing down (deleting) a cpuset is changed from
$cpuset_destroy_delay <secs>
cpuset_destroy_delay <secs>
In addition, a new option is available:
alloc_nodes_greedy <0 or 1>
PBS Pro 5.2 105
Administrator Guide
If set to 0, for job requests of 64 or fewer ssinodes, MOM will only allocate eligible
nodes that are within one router hop in the hypercube architecture, that is, those nodes that
are physically sitting close to each other. Otherwise if set to 1, MOM will allocate nodes
from all those available regardless of the distance (number of router hops) between them.
This latter case is the default behavior.
Upon daemon startup, MOM will not remove any cpusets that it
did not create. The nodes in these cpusets will be removed from
MOM’s available nodepool.
8.5.3 Enhanced cpuset Resource Reporting
MOM will now report to the Server the actual number of CPUs and memory that are under
the control of PBS. This allows the node's resources_available.{ncpus,mem}
to reflect the amount of resources that come from nodeboards that are not part of the
reserved, system cpusets (e.g. boot) and stuck cpusets. Be sure to unset any manual
settings of resources_available.{ncpus,mem} in both the node and the Server
to get this count automatically updated by MOM. Manual settings (i.e. those either put in
the server's nodes file or via the qmgr set node construct) take precedence.
8.5.4 Node Allocation Rules within MOM
Some special node and CPU allocation rules are now enforced by MOM:
If cpuset_create_flags set during cpusetCreate() contains a flag for
be allowed to be part of a cpuset.
During allocation of nodes, nodeboard 0 will only be allocated if no other nodes are available to satisfy the request. Use of node 0 for jobs can be a source of performance degradation as the kernel heavily uses this node for system daemons.
Static Resources
To identify static resource names and values, the MOM configuration file can contain a
list of resource name/value pairs, one pair per line, separated by white space. These are
most often used by the alternate schedulers, but are listed here for completeness. The
names can be anything and are not restricted to actual hardware. For example the entry
“pongsoft 1” could be used to indicate to the Scheduler that a certain piece of soft-
106 Chapter 8
Configuring MOM
ware (“pong”) is available on this system. Another example could be the number of tape
drives of different types.
pongsoft 1
tapedat 1
tape8mm 1
Dynamic Resources
PBS provides the ability to extend the resource query capabilities of MOM by adding shell
escapes to the MOM configuration file. While this feature is most often used by the alternate and site-customized schedulers, the functionality is described in full here. Another
use is to add site-specific information to the PBS monitoring tool, xpbsmon.
If the first character of the value portion of a name/value pair is the exclamation mark
(“!”), the entire rest of the line is saved to be executed through the services of the system(3) standard library routine. The first line of output from the shell command is
returned as the response to the resource query.
The shell escape provides a means for the resource monitor to yield arbitrary information
to the Scheduler and other client commands. Parameter substitution is done such that the
value of any qualifier sent with the resource query, as explained below, replaces a token
with a percent sign (%) followed by the name of the qualifier. For example, here is a configuration file line which gives a resource name of “echotest”:
echotest !echo %xxx %yyy
If a query for “echotest” is sent with no qualifiers, the command executed would be
“echo %xxx %yyy”. If one qualifier is sent, “echotest[xxx=hi]”, the command
executed would be “echo hi %yyy”. If two qualifiers are sent, “echotest
[xxx=hi] [yyy=there]”, the command executed would be “echo hi there".
If a qualifier is sent with no matching token in the command line, “echotest
[zzz=snafu]”, an error is reported.
Another example would allow the Scheduler to have MOM query the existence of a file.
The following entry would be placed in MOM’s config file:
PBS Pro 5.2 107
Administrator Guide
file_test !if test -f %file; then echo yes; else echo no; fi
The query string
file_test [file=/tmp/lockout]
would return “yes” if the file exists and “no” if it did not.
Another possible use of the shell command configuration entry is to provide a means by
which the use of floating software licenses may be tracked. If a program can be written to
query the license server, the number of available licenses could be returned to tell the
Scheduler if it is possible to run a job that needs a certain licensed package.
Idle Workstation Cycle Harvesting
“Harvesting” of idle workstations is a method of expanding the available computing
resources of your site by automatically including in your cluster unused workstations that
otherwise would have sat idle. This is particularly useful for sites that have a significant
number of workstation that sit on researchers desks and are unused during the nights and
weekends. With this feature, when the “owner” of the workstation isn’t using it, the
machine can be configured to be used to run PBS jobs.
If a system is configured for cycle harvesting, it becomes available for batch usage by PBS
if its keyboard and mouse remain unused or idle for a certain period of time. The workstation will be shown in state "free" when the status of the node is queried. If the keyboard or
mouse is used, the workstation becomes unavailable for batch work and PBS will suspend
any running jobs on that workstation and not attempt to schedule any additional work on
that workstation. The workstation will be shown in state "busy", and any suspended jobs
will be shown in state "U", a new state.
Jobs on workstations that become busy will not be migrated;
they remain on the workstation until they complete execution,
are rerun, or are deleted.
The cycle harvesting feature is enabled via a single entry in pbs_mom's config file,
$kdb_idle, and takes up to three parameters, as shown below.
108 Chapter 8
Configuring MOM
$kdb_idle idle_available [ idle_busy [ idle_poll ] ]
These three parameters, representing time specified in seconds, control the transitions
between free and busy states. Definitions follow.
is the time that the workstation keyboard and mouse must be
idle before the workstation is available to PBS.
is a time period which the keyboard or mouse must remain busy
before the workstation "stays" unavailable. This is used to keep
a single key stroke or mouse movement from keeping the workstation busy.
is how often the state of the keyboard and mouse are checked.
Let us consider the following example.
$kdb_idle 1800 10 5
Adding the above line to MOM’s config file directs PBS to mark the workstation as free if
the keyboard and mouse are idle for 30 minutes (1800 seconds), to mark the workstation
as busy if the keyboard or mouse are used for 10 consecutive seconds, and the state of the
keyboard/mouse is to be checked every 5 seconds.
The default value of idle_busy is 10 seconds, the default for idle_poll is 1 second. There is
no default for idle_available; setting it to non-zero is required to activate the cycle harvesting feature.
Elaborating on the above example will help clarify the roll of the various times. Lets start
with a workstation that has been in use for some time by its owner. The workstation is
shown in state busy. Now the owner goes to lunch. After 1800 seconds (30 minutes), the
system will change state to free and PBS may start assigning jobs to run on the system. At
some point after the workstation has become free and a job is started on it, someone walks
by and moves the mouse or enters a command. Within the next 5 seconds, pbs_mom
notes the activity. The job is suspended and shown being in state "U" and the workstation
is marked busy. If, after 10 seconds have passed and there is no addition keyboard/mouse
activity, the job is resumed and the workstation again is shown as free. However, if key-
PBS Pro 5.2 109
Administrator Guide
board/mouse activity continued during that 10 seconds, then the workstation would
remain busy and the job would remain suspended for at least the next 1800 seconds.
MOM Globus Configuration
For the optional Globus MOM, the same configuration mechanism applies as with the regular MOM except only three initiation value directives are applicable: $clienthost,
$restricted, $logevent.
8.10 Example: Single Server
The following examples are for a site called “The WyeWidget Company” whose domain
name is “wyewidget.com”. The following is an example of a config file for pbs_mom
where the batch system is a single large multi-processor server. We want to log most
records and specify that the system has one 8mm tape drive. In addition, the Scheduler
runs on a front end machine named front.widget.com.
$logevent 0x0ff
$clienthost front.wyewidget.com
tape8mm 1
8.11 Example: Cluster
Now the WyeWidget Computer Center has expanded to two large systems. The new system has two tape drives and is 30% faster than the old system. The PBS Manager wishes
to charge the users the same regardless of where their job runs. Basing the charges on the
old system, she will need to multiple the time used on the new system by 1.3 to charge the
same as on the old system. The config file for the “old” system stays the same. The config
file for the “new” system is:
$logevent 0x0ff
$clienthost front.wyewidget.com
$cputmult 1.3
$wallmult 1.3
tape8mm 2
110 Chapter 8
Configuring MOM
Now the WyeWidget Company has decided to assemble a cluster of PCs running Linux
named “bevy”, as in a bevy of PCs. The Scheduler and Server are running on bevyboss.wyewidget.com which also has the user’s home file systems mounted under
The nodes in the cluster are named bevy1.wyewidget.com, bevy2.wyewidget.com, etc.
The user’s home file systems are NFS mounted as /r/home/... The administrator’s
personal workstation, adm.wyewidget.com, is where she plans to run xpbsmon to do
cluster monitoring. The config file for each MOM would look like:
$logevent 0x0ff
$clienthost bevyboss.wyewidget.com
$restricted adm.wyewidget.com
$usecp bevyboss.wyewidget.com:/u/home /r/home
PBS Pro 5.2 111
Administrator Guide
Chapter 9
Configuring the Scheduler
Now that the Server and MOMs have been configured, we turn our attention to the Scheduler. As mentioned previously, the Scheduler is responsible for implementing the local site
policy by which jobs are run, and on what resources. This chapter discusses the default
configuration created in the installation process, and describes the full list of tunable
parameters available for the PBS Standard Scheduler.
9.1 Default Configuration
This Standard Scheduler provides a wide range of scheduling policies. It provides the ability to sort the jobs in several different ways, in addition to FIFO order. It also has the ability to sort on user and group priority, as well as many other features. As distributed, it is
configured with the following options (which are described in detail below).
Three specific system resources are checked to make sure they are
not exceeded: mem (memory requested), ncpus (number of CPUs
requested) and arch (architecture requested).
Queues are sorted by queue priority attribute to determine the order
in which they are to be considered.
All jobs in the current queue will be considered for execution before
112 Chapter 9
Configuring the Scheduler
considering any jobs from the next queue.
The jobs within each queue are sorted by requested cpu time
(cput). The shortest job is placed first.
Jobs which have been queued for more than one day will be
considered starving and extra measures will be taken to attempt
to run them.
Any queue whose name starts with “ded” is treated as a dedicated time queue (see discussion below). Sample dedicated time
file (/var/spool/sched_priv/dedicated_time) is
included in the installation.
Prime time is set to 6:00 AM - 5:30 PM. Any holiday is considered non-prime. Standard U.S. federal holidays for the year
2001 are provided in the file /var/spool/PBS/
sched_priv/holidays. These dates should be adjusted
yearly to reflect your local holidays.
In addition, the scheduler utilizes the following attributes/
resources in making scheduling decisions:
>= resources requested by job
& queue
>= number of jobs running
& queue
>= number of jobs running for a user
& queue
>= number of jobs running for a group
& queue
>= usage of specified resource by user
& queue
>= usage of specified resource by user
(see discussion of soft limits)
PBS Pro 5.2 113
Administrator Guide
& queue
>= maximum running jobs for a user
(see discussion of soft limits)
& queue
>= maximum running jobs for a group
(see discussion of soft limits)
= true
= execution
= queued
< configured limit
= type requested by job
= name or property requested by job
>= number of jobs running
>= number of jobs running for a user
>= number of jobs running for a group
>= resources requested by job
9.2 New Scheduler Features
With each PBS Pro release, new features are added to the Standard Scheduler. This section
discusses the new scheduler features available in PBS Pro 5.2, and how you may best take
advantage of these changes.
9.2.1 Preemption Enhancement
There are now multiple preemption levels. Three completely new levels, plus the existing
high priority queue, and starving jobs. There is now a concept of a user being over it's fairshare usage. The other two levels are queue and server soft limits. Before you could set a
limit on the number of jobs run. Those were hard limits and some of the system could be
held idle if those limits were met. Now you can set soft limits. If a user/group hits a soft
limit, they are allowed to temporarily exceed it. If another job which isn't over a limit,
over-limit jobs can be preempted to allow the more deserving jobs to run.
114 Chapter 9
Configuring the Scheduler
The preempt_prio parameter provides a means of specifying the order of precedence
that preemption should take. The ordering is evaluated from left to right. One special
name (normal_jobs) this is the default. If you want normal jobs to preempt other lower
priority jobs put normal_job in the middle of the preempt_prio list. If two or more
levels are desired for one priority setting, the multiple levels may be indicated by putting a
'+' between them. A complete listing of the preemption levels is provided in the scheduler
tunable parameters section below.
Two preemption levels can be turned on and off by specific sched_config parameters:
preempt_fairshare to enable preemption by fairshare; and preempt_starving
to have starving jobs preempt other jobs.
Soft run limits can be set or unset via qmgr. If unset, any job that would have been subject to this limits will instead be considered a "normal job". (Likewise, if
preempt_fairshare or preempt_starving are set to false, applicable jobs
will instead be treated as “normal jobs” too.) A new job sort has been added
(preempt_priorty) which will sort jobs by their preemption priority.
Note that any queue with a priority 150 (default value) is treated
as an express queue.
9.2.2 Site-Specified Fairshare Resources
The fairshare code has been enhanced to allow an administrator to set which PBS resource
is collected for fairshare usage. Previously it was always set to cput. If unspecified, the
default it is still cput. The resource to use is specified in the sched_config file with the
parameter: fairshare_usage_res.
9.2.3 Fairshare entity
An Admin can now change what the fairshare "entity” is. Previously it was always set to
the user. Now it can be set to any PBS job attribute (i.e. euser, egroup,
Account_Name, etc). The fairshare entity is set in the sched_config file with the
parameter: fairshare_entity.
9.2.4 Hierarchical Fairshare
New in release 5.2 is the change from a flat fairshare tree to a hierarchical fairshare tree.
This permits enforcing fairshare across groups of people rather than just individuals. Previously, the fairshare tree was used to create an initial hierarchy of percentages for sorting
PBS Pro 5.2 115
Administrator Guide
and running jobs, but the enforcement was flat (i.e. per-user). Now the hierarchy is
extended to include enforcement as well. For example, consider a situation where Sally
and Bob are both in group A and Mark is in group B and Sally uses 100% of the machine
for a month. In prior releases of PBS Pro, Bob and Mark would compete for cycles since
neither of them had any usage (i.e. comparison of individuals within the fairshare tree).
Now, with a hierarchal fairshare tree, since group A has all of Sally’s usage, group B has
much higher priority. Thus Mark's jobs would run before Bob’s.
9.3 Tunable Parameters
To tune the behavior of the Standard Scheduler, change directory to /var/spool/PBS/
sched_priv and edit the scheduling policy configuration file sched_config or use
the default values. This file controls the scheduling policy (the order in which jobs run).
The format of the sched_config file is:
name: value [prime | non_prime | all | none]
name can not contain any whitespace, but value may if the string is double-quoted.
value can be: true | false | number | string. Any line starting with a “#” is a comment, and
is ignored. A blank third word is equivalent to “all” which is both prime and non-primetime.
The available options for the Standard Scheduler, and the default values, are as follows.
boolean: If true, will enable ssinode-based scheduling (i.e. support for IRIX cpusets), including updating the ncpus and memory
resources to match the maximum amounts available on a given ssinode. If false, cpuset support is disabled. For more information see
section 9.3.1 “Scheduler Support for SGI IRIX cpusets” on page
Default: false
boolean: Instead of draining the system until the starving job runs,
the Scheduler will attempt to backfill smaller jobs around the starving jobs. It will first attempt to schedule other starving jobs around
it, before moving onto normal jobs. The help_starving_jobs
attribute needs to be on in conjunction with this attribute.
Default: true all
116 Chapter 9
Configuring the Scheduler
boolean: Directs the scheduler not to run jobs which will overlap into primetime or non-primetime. This will drain the system
before primetime or non-primetime starts, assisting with the
problem where a large job is run in non-primetime right before
non-primetime ends. See also prime_spill.
Default: false all
boolean: If true, the jobs will be run queue by queue; if
false, the entire job pool in the Server is looked at as one
large queue.
Default: true all
Obsolete. See “Scheduler Support for SGI IRIX cpusets” on
page 122 below.
string: Queue names with this prefix will be treated as dedicated
queues, meaning jobs in that queue will only be considered for
execution if the system is in dedicated time as specified in the
configuration file sched_priv/dedicated_time.
Default: ded
boolean: This will enable the fair share algorithm. It will also
turn on usage collecting and jobs will be selected based on a
function of their recent usage and priority(shares). See also section 9.3.7 “Defining Fair Share” on page 127.
Default: false all
string: Specifies the resource to collect and use in fairshare calcuations. (Can be any valid PBS resource.)
Default: cput
string: Specifies the job attribute to use as the fairshare “entity”.
(Can be any valid PBS job attribute, such as “euser”, “egroup”,
“Account_Name”, or “queue” ).
Default: euser
time: The half life for fair share usage. Requires fair_share
to be enabled. See also section 9.3.7 “Defining Fair Share” on
page 127.
Default: 24:00:00
PBS Pro 5.2 117
Administrator Guide
boolean: Setting this option will enable starving jobs support. Once
jobs have waited for the amount of time given by max_starve
they are considered starving. If a job is considered starving, then no
jobs will run until the starving job can be run, unless backfilling is
also specified. To use this option, the max_starve configuration
attribute needs to be set as well. See also backfill.
Default: true all
boolean: If set, the Scheduler will load balance the jobs across the
nodes. The load balancing takes into consideration the load on each
node as well as all resources specified in the “resource” list. See
Default: false all
Obsolete. To duplicate this setting, enable load_balancing and
set smp_cluster_dist to round_robin.
integer: Defines which event types to filter from the daemon logfile.
The value should be set to the bitwise OR of the event classes which
should be filtered. See also section 11.13 “Use and Maintenance of
Logfiles” on page 158.
Default: 256 (DEBUG2)
time: The amount of time before a job is considered starving. This
variable is used only if help_starving_jobs is set.
Default: 24:00:00
Obsolete. See “Scheduler Support for SGI IRIX cpusets” on
page 122 below.
string: Queue names which start with this prefix will be treated as
non-primetime queues. Jobs within these queues will only run during non-primetime. Primetime and nonprimetime are defined in the
holidays file.
Default: np_
string: Queue names which start with this prefix will be treated as
primetime queues. Jobs will only run in these queues during prime-
118 Chapter 9
Configuring the Scheduler
time. Primetime and non-primetime are defined in the holidays file.
Default: p_
string: Enable job preemption. See “Preemptive Scheduling” on
page 124 for details.
Default: true all
boolean: Specifies if preemptable jobs should be checkpointed
(if supported by underlying operating system).
Default: true
boolean: Specifies if jobs over their “fairshare” limits should be
treated as preemptable or not.
Default: false
quoted list: Defines the order in which the scheduler will
attempt to preempt jobs. This order can change depending on
the percentage of time remaining on the job. The ordering can
be any combination of S C and R (for suspend, checkpoint, and
requeue). The usage is an ordering (SCR) optionally followed
by a percentage of time remaining and another ordering. Note,
this has to be a quoted list("").
Default: SCR
preempt_order: "SR"
# or
preempt_order: "SCR 80 SC 50 S"
The first example above specifies that PBS should first attempt
to use suspension to preempt a job, and if that is unsuccessful,
then requeue the job. The second example says if the job has
between 100-81% of requested time remaining, first try to suspend the job, then try checkpoint then requeue. If the job has
between 80-51% of requested time remaining, then attempt suspend then checkpoint; and between 50% and 0% time remaining just attempt to suspend the job.
quoted list: Specifies the ordering of priority of different preemption levels. Two or more job types may be combined at the
same priority level with a “+” between them. Otherwise,
comma-separated preemption levels are evaluation left to right,
with each having lower priority than the preemption level preceding it. The table below lists the six preemption levels.
Default: “express_queue, normal_jobs”
PBS Pro 5.2 119
Administrator Guide
jobs in the preemption queue(s) preempt
when a job becomes starving it can preempt
when a job uses too much of it's fairshare
jobs who are over their queue soft limits
jobs who are over their server soft limits
default for normal jobs
preempt_prio "starving_jobs, normal_jobs, fairshare"
# or
"starving_jobs, normal_jobs, starving_jobs+fairshare"
integer: Specifies the minimum queue priority required for a queue
to be classified as an express queue.
Default: 150
boolean: Specifies if preemptable jobs should be requeued.
Default: true
boolean: Specifies if “starving” jobs should be treated as preemptable or not.
Default: true
boolean: Specifies if preemptable jobs should be suspended.
Default: true
time: Specifies the amount of time a job can "spill" over from nonprimetime into primetime or from non-primetime into primetime.
For example, if a job is in a primetime queue and it is currently
primetime, but the job would cross over into non-primetime by one
hour, the job would not run if prime_spill were set to less than
one hour. Note, this option is only meaningful if
backfill_prime is true. Also note that this option can be sepa-
120 Chapter 9
Configuring the Scheduler
rately specified for prime- and non-primetime.
Default: 00:00:00
string: Specifies the resources by which to schedule the system.
Limits are set by setting resources_available.resourceName on
the Server objects (nodes, queues, and servers). The scheduler
will consider numeric (int or float) items as consumable
resources and ensure that no more are assigned than are available (e.g. ncpus or mem). Any string resources will be compared using string comparisons (e.g. arch). See the description
of the Server attribute resources; see also section “Dynamic
Consumable Resources” on page 126.
Default: “ncpus, mem, arch” (number CPUs, memory,
boolean: If true, the queues will be cycled through in a circular fashion, attempting to run one job from each queue. If
false, attempts to run all jobs from the current queue before
processing the next queue. See by_queue.
Default: false all
string: Specifies how jobs should be distributed to all nodes of
the cluster. Options are: pack, round_robin, and
lowest_load. pack means keep putting jobs onto one node
until it is “full” and then move onto the next. round_robin is
to put one job on each node in turn before cycling back to the
first one. lowest_load means to put the job on the lowest
loaded node.
Default: pack all
string: Selects how the jobs should be sorted. sort_by can be
set to a single sort type or to multi_sort. If set to
multi_sort, multiple key fields are used. Each key field will
be a key for the multi_sort. The order of the key fields
decides which sort type is used first. Each sorting key is listed
on a separate line starting with the word key
Default: shortest_job_first all
PBS Pro 5.2 121
Administrator Guide
Sort Keys
Sort based on the values in the resource
group file. This should only used if strict
priority sorting is needed. Do not enable
fair_share sorting if using the
fair_share scheduling option.
Descending by the job priority attribute
Descending by job walltime attribute
Descending by the mem attribute
Descending by the cput attribute
Ascending by the job priority attribute
Sort on multiple keys.
Do not sort the jobs
sort jobs by preemption priority
Ascending by the cput attribute
Ascending by the walltime attribute
Ascending by the mem attribute
The following example illustrates how to define a multi-sort
using three of the above sort keys:
sort_by: multi_sort
key: sortest_job_first
key: smallest_memory_first
key: high_priority_first
boolean: If true, jobs will be run in a strict FIFO order. This
means if a job fails to run for any reason, no more jobs will run
from that queue/Server during that scheduling cycle. If
strict_fifo is not set, large jobs can be starved, i.e., not
122 Chapter 9
Configuring the Scheduler
allowed to run because a never ending series of small jobs use
the available resources. Also see the Server attribute
help_starving_jobs and backfill above.
Default: false all
time: The amount of time between writing the fair share usage
data to disk. Requires fair_share to be enabled.
Default: 1:00:00
integer: The amount of shares for the "unknown" group.
Requires fair_share to be enabled. See also section 9.3.7
“Defining Fair Share” on page 127.
Default: 10
9.3.1 Scheduler Support for SGI IRIX cpusets
As discussed earlier in this manual, PBS Pro supports the use of SGI IRIX “cpusets” (or
named regions of an SGI IRIX system containing specific CPUs and associated memory).
If support for SGI cpusets is desired, it needs to be enabled in the Scheduler. (See also section 4.4.2 “Installing MOM with SGI “cpuset” Support” on page 24).
In the Scheduler, cpuset support is accomplished by setting assign_ssinodes:true
in the Scheduler’s configuration file. The number of CPUs and amount of memory per
node board within the system are queried directly from the MOM local to that system.
This permits running clusters of SGI Origin systems with different hardware configurations managed by a single PBS Scheduler. The Scheduler will modify the mem and/or
ncpus request of jobs into values that corresponds to nodeboard multiples (i.e. adjusting
upward to the fewest number of entire nodeboards necessary to fill both the memory and
CPU request of the job). The Scheduler also sets the ssinodes resource used by MOM.
9.3.2 SMP Cluster Support
The Standard Scheduler schedules SMP clusters in an efficient manner. Instead of scheduling only via load average of nodes, it takes into consideration the resources specified at
the server, queue, and node level. Furthermore, the administrator can explicitly select the
resources to be considered in scheduling via an option in the Scheduler’s configuration file
(resources). The configuration parameter smp_cluster_dist allows you to specify how nodes are selected. The available choices are pack (pack one node until full),
round_robin (put one job on each node in turn), or least_loaded (put one job on
the least loaded node).
PBS Pro 5.2 123
Administrator Guide
To use these features requires two steps: setting resource limits via the Server, and specifying the scheduling options. Resource limits are set using the resources_available
attribute of nodes via qmgr just like on the server or queues. For example, to set maximum limits on a node called “node1” to 10 CPUs and 2 GB of memory:
Qmgr>set node node1 resources_available.ncpus = 10
Qmgr>set node node1 resources_available.mem=2GB
Note that by default both resources_available.ncpus
and resources_available.mem are set to the physical
number reported by MOM on the node. Typically, you do not
need to set these values, unless you do not want to use the actual
values reported by MOM.
Next, the Scheduler options need to be set. For example, to enable SMP cluster scheduler
to use the “round robin” algorithm during primetime, and the “pack” algorithm during
non-primetime, set the following in the Scheduler’s configuration file:
smp_cluster_dist: round_robin prime
smp_cluster_dist: pack
Finally, specify the resources to use during scheduling (also in the Scheduler’s configuration file):
resources: “ncpus, mem”
9.3.3 Enhanced Load Balancing
The load balancing feature of PBS Pro changed with release 5.1 to allow load-balancing
without oversubscribing memory. If you wish to schedule via load and not over-allocate
memory, then remove "ncpus" from the Scheduler’s resources parameter (i.e. set
resources: “mem”). The load_balancing scheduling parameter needs to be set
124 Chapter 9
Configuring the Scheduler
like before. The following example illustrates this:
smp_cluster_dist: pack
The load_balancing_rr parameter has been obsoleted (although it has been retained
for backward compatibility). If you wish to load balance via the round robin algorithm, set
the following in the Scheduler’s configuration file:
smp_cluster_dist: round_robin
9.3.4 Preemptive Scheduling
PBS provides the ability to preempt currently running jobs in order to run higher priority
work. Preemptive scheduling is enabled by setting several parameters in the Scheduler’s
configuration file (discussed below, and in “Tunable Parameters” on page 115). Jobs utilizing advance reservations are not preemptable. If priority jobs (as defined by your settings on the above parameters) can not run immediately, the scheduler looks for jobs to
preempt, in order to run the higher priority job. A job can be preempted in several ways.
The scheduler can suspend the job (i.e. sending a SIGSTOP signal), checkpoint the job (if
supported by the underlying operating system), or requeue the job. (The administrator can
choose the order of these attempts via the preempt_order parameter.)
There are eight Scheduler parameters to control preemption. The preemptive_sched
parameter turns preemptive scheduling on and off. You can specify the relative priority
between different types of jobs using preempt_prio. You set what queue priority is
preemptive with the preempt_queue_prio parameter. The preempt_fairshare
parameter indicates whether jobs that are “over” their fairshare limits should be treated as
preemptable or not.
The last four set how you want to preempt work: preempt_suspend,
preempt_checkpoint, preempt_requeue and preempt_order The first three
indicate which preemption methods you wish to enable, and the last allows you to specify
the order in which these methods should be applied. If one preemption method fails, the
Scheduler tries the next. If the scheduler cannot find enough work to preempt in order to
run a given job, it will not preempt any work.
PBS Pro 5.2 125
Administrator Guide
If using cpusets on an Origin 2K/3K, set preempt_suspend
to False. If set to True, the job will be suspended, but the
cpuset will not be freed, leaving the resource unavailable to
other jobs.
Below is an example of (part of) the Scheduler’s configuration file showing how to enable
preeptive scheduling and related parameters. Explantory comments preceed each configuration parameter.
# turn on preemptive scheduling
# set the queue priority level for express queues
# enable all three methods of preemption
# allow jobs marked starving to preempt
# disable preemption based on fairshare
# specifiy the priority of jobs as: express queue (highest)
# then starving jobs, then normal jobs, followed by jobs
# who are staving but the user/group is over a soft limit,
# followed by users/groups over their soft limit but not
# starving
preempt_prio: "express_queue, starving_jobs, normal_jobs,
starving_jobs+over_server_limit, over_server_limit"
# specify when to each preemption method. If the first
# method fails, try the next method. If a job is has
# between 100-81% time remaining, try to suspend, then
# checkpoint then requeue. From 80-51% suspend and then
# checkpoint, but don't requeue. If between 50-0% time
# remaining, then just suspend it.
preempt_order: "SCR 80 SC 50 S"
126 Chapter 9
Configuring the Scheduler
9.3.5 Dynamic Consumable Resources
It is possible to schedule resources where the number of available resources are outside of
PBS's control. The Scheduler will perform a resource query to MOM to get the current
availability for the resource and use that value for scheduling. These resources are specified in the Scheduler’s configuration file using the parameter, mom_resources. These
resources are queried from every MOM in the cluster and if the MOM returns a value it
will replace the resources_available value reported by the Server. If the MOM
returns no value, the value from the Server is kept. If neither specify a value, the Scheduler
sets the resource value to 0. To use this feature, follow these steps:
Step 1
Create new resources on the Server (.../server_priv/
resourcedef file). See also “Defining New Resources” on
page 87
Step 2
Set resource queries in MOM config files. See also
“Dynamic Resources” on page 106.
Step 3
Set mom_resources parameter to these new resources. See
As an illustrative example, suppose your company has ten licenses to an expensive Astrology program, but its use is limited to a single node (named “twinkie”). Things are further
complicated by the marketing department demanding you reserve two licenses for their
business planning seances. You’ve been told to limit everyone else to at most eight
licenses. You decide that PBS should do this, so you write a quick shell script (called
count_astro_licenses) to query the license manager and report the total number
of licenses that you want PBS to manage. (This could be useful, for example, if there are
other programs outside of PBS that may use these licenses. Your script can detect this, and
reduce the number that PBS should manage.). Now you are ready to configure PBS.
First you edit the Server’s resource file (.../server_priv/resourcedef) adding
a definition for your new resource. Let’s call it “astrology”:
type=long flag=qn
Note that the n flag is important in order to have the Server calculate values of
resources_assigned for this new resource.
PBS Pro 5.2 127
Administrator Guide
Next, you configure MOM to use your little shell script to query the Astrology licenses, by
entering one line into the mom_priv/config file:
astrology !/usr/local/bin/count_astro_licenses
And finally, you edit the Scheduler configuration file, specifying this new resource that
you want queried and used for scheduling:
mom_resources: “astrology”
9.3.6 Defining Dedicated Time
The file /usr/spool/PBS/sched_priv/dedicated_time defines the dedicated times for the scheduler. During dedicated time, only jobs in the dedicated time
queues can be run (see dedicated_prefix above). The format of entries is:
# From Date-Time
To Date-Time
# For example
04/15/2001 12:00 04/15/2001 15:30
9.3.7 Defining Fair Share
PBS fairshare is similar to the UNICOS implementation of fairshare. Users are put in a
fairshare group file. The file is read in and a tree is created. The tree consists of groups
(nodes) and entities (leaves). Groups can contain groups. Every node and leaf has a number of shares associated with it. Priorities can be derived from these shares by taking a
ratio of them to all the rest of the shares.
For example, say you have three nodes/leaves at one level with shares of 10, 20, and 10.
The first user/group has a priority of 25% or 10/40, the second has 50% or 20/40 and so
on. A node with children can establish priorities among them via shares. So if in the example above the second group (50%) is actually a group with 4 users and all the users have
equal shares, then each user has 1/4 of 50% or 12.5% of the machine.
If fair share or strict priority is going to be used, the resource group file /var/spool/
PBS/sched_priv/resource_group may need to be edited. (If all users are consid-
128 Chapter 9
Configuring the Scheduler
ered equal, this file doesn’t need to be edited.) Each line of the file should use the following format:
name unique_ID parent_group shares
The name of the specified entity or group
A unique numeric identifier for the group or entity
The name of the parent resource group to which this user/group
belongs. The root of the share tree is called root and is added
automatically to the tree by the Scheduler.
The number shares (or priority) the user/group has in the specified resource group.
If you wish to specify how individual users should be ranked against each other, only user
entries are required in the resources_group file, as shown the following example:
Another option is to divide shares into “groups”, and then name the users who are members of each group. The following example illustrates this configuration:
The above example shows three top level groups (whose parent is the root group), three
PBS Pro 5.2 129
Administrator Guide
sub-groups (whose parent is a user-defined group), and 10 users belonging to different
groups. The box below shows how the individual shares or percentages are calculated for
groups and users, using the values from the above example. First we start with the root
group as having 100% of the machine, but it has three member groups and one user, with
share values of 10, 20, 10, and 5, respectively, for a total of 45 shares. The second line
below shows calculating the actual percentage of the resources that group grp1 has. Specifically, the specified 10 shares are out of a total of 45 specified shares, or 22% of the
total. The members of group grp1 (i.e. user usr2 and groups grp4 and grp5) each have specific shares of their group, all of which together total 40 shares specified for this group
(i.e. 10+20+10). Thus their specified shares are of this total, resulting in these three entities having 25%, 50%, and 25%, respectively, of group grp1. We can further calculate how
these share convert into shares of the total system by multiplying against the total percentage possessed by their group, grp1.
root 100%
grp1 10 10/45 = 100% * 22% = 22%
usr2 10 10/40 (25%) * 22% = 5.5%
grp4 20 20/40 (50%) * 22% = 11%
usr8 10 10/20 (50%) * 11% = 5.5%
usr9 10 10/20 (50%) * 11% = 5.5%
grp5 10 10/40 (25%) * 22% = 5.5%
usr10 10 100% * 5.5% = 5.5%
grp2 20 20/45 = 100% * 44% = 44%
usr3 10 10/30 (33%) * 44% = 14.5%
grp6 20 20/30 (66%) * 44% = 29%
usr4 10 10/40 (25%) * 29% = 7.2%
usr5 10 10/40 (25%) * 29% = 7.2%
usr6 20 20/40 (50%) * .29% = 14.5%
grp3 10 10/45 = 22%
usr7 10 100% * 22% = 22%
usr1 5 5/45 = 11%
9.3.8 Defining Strict Priority
Not to be confused with fair share (which considers past usage of each entity in the selection of jobs), the Standard Scheduler offers a sorting key called “fair_share”. Selecting this option enables the sorting of jobs based on the priorities specified in the fair share
tree (as defined above in the resource_group file). A simple share tree will suffice.
130 Chapter 9
Configuring the Scheduler
Every user’s parent_group should be root. The amount of shares should be their
desired priority. unknown_shares (in the scheduler’s configuration file) should be set
to one. Doing so will cause everyone who is not in the tree to share one share between
them, making sure everyone else in the tree will have priority over them. Lastly,
sort_by must be set to fair_share.This will sort by the fair share tree which was
just set up. For example:
9.3.9 Defining Primetime and Holidays
To have the scheduler utilize and enforce holidays, edit the /usr/spool/PBS/
sched_priv/holidays file to handle prime time and holidays. The holidays file
should use the UNICOS 8 holiday format. The ordering is important. Any line that begins
with a "*" is considered a comment. The format of the holidays file is:
This is the current year.
<day> <prime> <nonprime>
<day> <prime> <nonprime>
Day can be weekday, saturday, or sunday
Prime and nonprime are times when prime or non-prime time start. Times can either be
HHMM with no colons(:) or the word "all" or "none"
<day> <date> <holiday>
Day is the day of the year between 1 and 365 ( e.g. “1”)
Date is the calendar date (e.g. “Jan 1”)
Holiday is the name of the holiday (e.g. “New Year’s Day”)
PBS Pro 5.2 131
Administrator Guide
* Day
* Day of
* Year
Jan 1
Jan 21
Feb 18
May 27
Jul 4
Sep 2
Oct 7
Nov 11
Nov 28
Dec 25
Company Holiday
New Year's Day
Martin Luther King Day
President's Day
Memorial Day
Independence Day
Labor Day
Columbus Day
Veteran's Day
Christmas Day
PBS Pro 5.2 132
Administrator Guide
PBS Pro 5.2 133
Administrator Guide
Chapter 10
Example Configurations
Up to this point in this manual, we have seen many examples of how to configure the individual PBS daemons, set limits, and otherwise tune a PBS installation. Those examples
were used to illustrate specific points or configuration options. This chapter pulls these
various examples together into configuration-specific scenarios which will hopefully clarify any remaining configuration questions. Four configuration models are discussed, each
more complex than the one before it:
Single Node Time-sharing System
Single Node System with Separate PBS Server
Multi-node Time-sharing Cluster
Multi-node Space-sharing Cluster
For each of these possible configuration models, the following information is provided:
General description for the configuration model
Type of system the model is well suited for
Graphic illustration of the model
Contents of Server nodes file
Any required settings in Server
Contents of MOM configuration file
Required settings in Scheduler configuration file
134 Chapter 10
Example Configurations
10.1 Single Node Time-sharing System
Running PBS on a single node/host as a standalone time-sharing system is the least complex configuration. This model is most applicable to sites who have a single large Server
system, or even a vector supercomputer. In this model, all three PBS daemons run on the
same host, which is the same host on which jobs will be executed, as shown in the figure
All daemons on a single host.
For this example, lets assume we have a 32-CPU server machine named “mars”. We want
users to log into “mars” and jobs will be run via PBS on mars.
In this configuration, the default PBS nodes file (which should contain the name of the
host on which the Server was installed) is sufficient. Our example nodes file would contain only one entry: mars:ts
The default MOM and Scheduler config files, as well as the default queue/Server limits
are also sufficient. No changes are required from the default configuration.
PBS Pro 5.2 135
Administrator Guide
10.2 Single Timesharing Node with Separate Server
A variation on this model would be to provide a “front-end” system that ran the PBS
Server and Scheduler, and from which users submitted their jobs. Only the MOM daemon
would run on our execution server, mars. This model is recommended when the user load
would otherwise interfere with the computational load on the Server.
execution host, mars
In this case, the PBS server_priv/nodes file would contain the name of our execution server mars, but this may not be what was written to the file during installation,
depending on which options were selected. It is possible the hostname of the machine on
which the Server was installed was added to the file, in which case you would need to
either manually edit the nodes file, or use qmgr(1B) to manipulate the contents to contain one node: mars:ts. If the default scheduling policy, based on available CPUs and
memory, meets your requirements, then no changes are required in either the MOM or
Scheduler configuration files.
However, if you wish the execution node (mars) to be scheduled based on load average,
the following changes are needed. Edit MOM’s mom_priv/config file so that it contains the target and maximum load averages, e.g.:
$ideal_load 30
$max_load 32
136 Chapter 10
Example Configurations
In the scheduler sched_priv/config file, the following options would need to be set:
load_balancing: true all
10.3 Multi-node Timesharing Cluster
The multi-node time-sharing cluster model is a very common configuration for PBS. In
this model, there is typically a “front-end” system as we saw in the previous example, with
a number of ‘back-end” compute nodes. The PBS Server and Scheduler are typically run
on the front-end system, and a MOM daemon is run on each of the execution nodes, as
shown in the diagram to the right.
In this model, the PBS nodes file will need to contain the list of all the nodes in the cluster, with the timesharing attribute :ts appended:
The MOM config file on each node will need two static resources added, to specify the
target load for each node. If we assume each of the nodes in our planets cluster is a 32-processor system, then the following example shows what might be desirable values to add to
the MOM config files:
$ideal_load 30
$max_load 32
Furthermore, suppose we want the Scheduler to load balance the workload across the
available nodes, making sure not to run two job in a row on the same node (round robin
node scheduling). We accomplish this by editing the Scheduler configuration file and
enabling load_balancing:
PBS Pro 5.2 137
Administrator Guide
load_balancing: true all
smp_cluster_dist: round_robin
Execution Host
Execution Host
Execution Host
Execution Host
Execution Host
Execution Host
Execution Host
Execution Host
This diagram illustrates multi-node cluster configurations wherein the Scheduler and
Server communicate with the MOMs on the execution nodes. Jobs are submitted to the
138 Chapter 10
Example Configurations
Server, scheduled for execution by the Scheduler, and then transferred to a MOM when
it’s time to be run. MOM periodically sends status information back to the Server, and
answers resource requests from the Scheduler.
10.4 Multi-node Space-sharing Cluster
A variation on the time-sharing cluster is the “space-shared” cluster. In this context, spacesharing refers to assigning an entire node (or set of nodes) to a single job at a time, for the
duration of the job. This is usually done in order to achieve high-throughput and predictability of runtimes for a specific application (such as message passing parallel jobs).
In this model, the PBS nodes file would not have the :ts appended to the node names,
There would be no edits required to either the Scheduler or the MOM config files.
Lastly, since in this model users specify their job resource requirements using the “-l
nodes=...” syntax of qsub, we need to set node-specific limits in the Server:
# qmgr
Qmgr: set server resources_default.nodes = 1
Qmgr: set server resources_default.nodect = 1
Qmgr: set server resources_default.neednodes = 1
PBS Pro 5.2 139
Administrator Guide
Chapter 11
This chapter covers information on the maintenance and administration of PBS, and as
such is intended for the PBS Manager. Topics covered include: starting and stopping PBS,
security within PBS, prologue/epilogue scripts, PBS accounting, configuration of the PBS
GUIs, and using PBS with other products such as Globus.
11.1 /etc/pbs.conf
During the installation of PBS Pro, the following /etc/pbs.conf file was created:
This configuration file controls which daemons are to be running on the local system,
directory tree location, and various runtime configuration options. Each node in a cluster
should have its own /etc/pbs.conf file. The following table describes the available
parameters as of the current version of PBS Pro:
140 Chapter 11
set to 1 if Server is to run on this host
set to 1 if a MOM is to run on this host
set to 1 if Scheduler is to run on this node
location of PBS working directories
location of PBS bin and sbin directories
hostname of host running the Server
location of scp command if scp is used
location of pbs_environment file
Port Server listens on
DIS Port Server listens on
Port MOM listens on
Port MOM Manager listens on
Port Scheduler listens on
Port Globus MOM listens on
Port Globus Manager listens on
11.2 Starting PBS Daemons
The daemon processes, Server, Scheduler, MOM and the optional MOM Globus, must run
with the real and effective uid of root. Typically the daemons are started automatically by
the system upon reboot. The boot-time start/stop script for PBS is /etc/init.d/pbs.
This script reads the /etc/pbs.conf file to determine which daemons should be
The startup script can also be run by hand to get status on the PBS daemons, and to start/
stop all the PBS daemons on a given host. The command line syntax for the startup script
/etc/init.d/pbs [ status | stop | start ]
PBS Pro 5.2 141
Administrator Guide
Alternately, you can start the individual PBS daemons manually, as discussed in the following sections. Furthermore, you may wish to change the options specified to various
daemons, as discussed below.
11.2.1 Manually Starting MOM
MOM should be started at boot time. Typically there are no required options. It works best
if MOM is started before the Server so she will be ready to respond to the Server’s “are
you there?” ping. Start MOM with the command line:
/usr/pbs/sbin/pbs_mom [options]
If MOM is taken down and the host system continues to run, MOM should be restarted
with either of the following options:
This directs MOM to let running jobs continue to run. Because
MOM is no longer the parent of the jobs, she will not be notified
(SIGCHLD) when they die and so must poll to determine when the
jobs complete. The resource usage information therefore may not
be completely accurate.
This directs MOM to kill off any jobs which were left running.
Without either the -p or the -r option, MOM will assume the jobs’ processes are nonexistent due to a system restart, a cold start. She will not attempt to kill the processes and
will request that any jobs which where running before the system restart be requeued.
Other command line options for MOM include:
-a alarm
Used to specify the alarm timeout in seconds for computing a
resource. Every time a resource request is processed, an alarm is set
for the given amount of time. If the request has not completed
before the given time, an alarm signal is generated. The default is 5
-C chkdir
Specifies the path of the directory used to hold checkpoint files.
[Currently this is only valid on Cray and SGI systems.] The default
directory is PBS_HOME/spool/checkpoint, see the -d
option. The directory specified with the -C option must be owned
142 Chapter 11
by root and accessible (rwx) only by root to protect the security
of the checkpoint files.
-c config
Specifies an alternative configuration file, see description
below. If this is a relative file name it will be relative to
PBS_HOME/mom_priv, see the -d option. If the specified
file cannot be opened, pbs_mom will abort. If the -c option is
not supplied, pbs_mom will attempt to open the default configuration file "config" in PBS_HOME/mom_priv. If this file is
not present, pbs_mom will log the fact and continue.
-d directory
Specifies the path of the directory which is the home of the
servers working files, PBS_HOME. This option is typically used
along with -M when debugging MOM. The default directory is
given by PBS_HOME which is typically /usr/spool/PBS.
-L logfile
Specify an absolute path name for use as the log file. If not
specified, MOM will open a file named for the current date in
the PBS_HOME/mom_logs directory, see the -d option.
-M port
Specifies the port number on which MOM will listen for batch
-n nice_val
Specifies the priority value of the daemon when it executes.
-R port
Specifies the port number on which MOM will listen for
resource monitor requests, task manager requests and interMOM messages. Both a UDP and a TCP port of this number
will be used.
Disables the check for privileged port resource monitor connections. This is used mainly for testing since the privileged port is
the only mechanism used to prevent any ordinary user from
11.2.2 Manually Starting the Server
Normally the PBS Server is started from the system boot file via a line such as:
/usr/pbs/sbin/pbs_server [options]
PBS Pro 5.2 143
Administrator Guide
The command line options for the Server include:
-a active
Specifies if scheduling is active or not. This sets the server attribute
scheduling. If the option argument is "true" ("True", "t", "T", or
"1"), the server is active and the PBS job scheduler will be called. If
the argument is "false" ("False", "f", "F", or "0), the server is idle,
and the scheduler will not be called and no jobs will be run. If this
option is not specified, the server will retain the prior value of the
scheduling attribute.
-d config
Specifies the path of the directory which is home to the Server’s
configuration files, PBS_HOME. A host may have multiple Servers.
Each Server must have a different configuration directory. The
default configuration directory is PBS_HOME which is typically set
to /usr/spool/PBS.
-e mask
Specifies a log event mask to be used when logging. See
“log_events” on page 68.
-p port
Specifies the port number on which the Server will listen for batch
requests. If multiple Servers are running on a single host, each must
have its own unique port number. This option is for use in testing
with multiple PBS systems on a single host.
-A acctfile
Specifies an absolute path name of the file to use as the accounting
file. If not specified, the file is named for the current date in the
PBS_HOME/server_priv/accounting directory.
-L logfile
Specifies an absolute path name of the file to use as the log file. If
not specified, the file is one named for the current date in the
PBS_HOME/server_logs directory, see the -d option.
-M mom_port
Specifies the host name and/or port number on which the server
should connect to the MOMs. The option argument, mom_port, is
one of the forms: host_name, [:]port_number, or
host_name:port_number. If host_name not specified, the
local host is assumed. If port_number is not specified, the
default port is assumed. See the -M option for pbs_mom.
144 Chapter 11
-R RPPport
Specifies the port number on which the Server should query the
status of MOM. See the -R option for pbs_mom.
-g globus_port
Specifies the host name and/or port number on which the Server
should connect the PBS MOM Globus daemon. The option
argument, globus_port, is one of the forms: host_name,
[:]port_number, or host_name:port_number. If
host_name not specified, the local host is assumed. If
port_number is not specified, the default port is assumed.
-G globus_RPP
Specifies the port number on which the Server should query the
status of PBS MOM Globus daemon.
-S sched_port
Specifies the port number to which the Server should connect
when contacting the Scheduler. The option argument,
sched_port, is of the same syntax as under the -M option.
-t type
Specifies the impact on jobs when the Server restarts. type argument is:
Effect Upon Job Running Prior to Server Shutdown
All jobs in the Running state are retained in that state. Any job that was
requeued into the Queued state from the Running state when the server last
shut down will be run immediately, assuming the required resources are
available. This returns the server to the same state as when it went down.
After those jobs are restarted, then normal scheduling takes place for all
remaining queued jobs. All other jobs are retained in their current state.
If a job cannot be restarted immediately because of a missing resource,
such as a node being down, the server will attempt to restart it periodically
for up to 5 minutes. After that period, the server will revert to a normal
state, as if warm started, and will no longer attempt to restart any remaining
jobs which were running prior to the shutdown.
All jobs in the Running state are retained in that state. All other jobs are
maintained in their current state. The job scheduler will typically make new
selections for which jobs are placed into execution. Warm is the default if
-t is not specified.
PBS Pro 5.2 145
Administrator Guide
Effect Upon Job Running Prior to Server Shutdown
All jobs are purged. Positive confirmation is required before this direction
is accepted.
The server will discard any existing configuration files: server, nodes,
queues and jobs, and initialize configuration files to the default values. The
server is idled (scheduling set false).
11.2.3 Manually Starting the Scheduler
The Scheduler should also be started at boot time. If starting by hand, use the following
command line:
/usr/pbs/sbin/pbs_sched [options]
There are no required options for the Standard Scheduler. Available options are listed
-a alarm
This specifies the time in seconds to wait for a schedule run to finish. If a script takes too long to finish, an alarm signal is sent, and
the scheduler is restarted. If a core file does not exist in the current
directory, abort() is called and a core file is generated. The default
for alarm is 180 seconds.
-d home
This specifies the PBS home directory, PBS_HOME. The current
working directory of the scheduler is PBS_HOME/sched_priv.
If this option is not given, PBS_HOME defaults to PBS_HOME as
defined in the /etc/pbs.conf file.
-L logfile
Specifies an absolute path name of the file to use as the log file. If
not specified, the scheduler will open a file named for the current
date in the PBS_HOME/sched_logs directory; see the -d
-p file
This specifies the "print" file. Any output from the Scheduler which
is written to standard out or standard error will be written to this file.
If this option is not given, the file used will be PBS_HOME/
sched_priv/sched_out. See the -d option.
146 Chapter 11
-S port
This specifies the port to use. If this option is not given, the
default port for the PBS Scheduler is used.
-R port
This specifies the resource monitor port to use. If this option is
not given, the default port for the PBS MOM is used.
-c file
Specify a configuration file. If this is a relative file name it will
be relative to PBS_HOME/sched_priv, see the -d option. If
the -c option is not supplied, pbs_sched will not attempt to
open a configuration file.
The options that specify file names may be absolute or relative. If they are relative, their
root directory will be PBS_HOME/sched_priv.
11.2.4 Manually Starting Globus MOM
The optional Globus MOM should be started at boot time if Globus support is desired.
Note that the provided startup script does not start the Globus MOM. There are no
required options. If starting manually, run it with the line:
/usr/pbs/sbin/pbs_mom_globus [options]
If Globus MOM is taken down and the host system continues to run, the Globus MOM
should be restarted with the -r option. This directs Globus MOM to kill off processes
running on behalf of a Globus job. See the PBS External Reference Specificiation (or
the pbs_mom_globus(1B) manual page) for a more complete explanation.
If the pbs_mom_globus daemon is restarted without the -r option, the assumption that
will be made is that jobs have become disconnected from the Globus gatekeeper due to a
system restart (cold start). Consequentially, pbs_mom_globus will request that any
Globus jobs that were being tracked and which where running be canceled and requeued.
11.3 Stopping PBS
PBS Pro version 5.1 introduced additional options to the qterm command that enable the
administrator to shutdown, selectively, or inclusively, the various PBS daemons.
directs that all pbs_moms should be shutdown
directs that the pbs_sched should be shut down
PBS Pro 5.2 147
Administrator Guide
Thus, the following command will bring down the entire PBS complex:
# qterm -s -m
There is a third option (“-t type”) available for the qterm command, which takes one
of three arguments for the type of shutdown you wish to perform.
type of
All running jobs are to immediately stop execution. If checkpoint is
supported, running jobs that can be checkpointed are checkpointed, terminated, and requeued. If checkpoint is not supported or the job cannot
be checkpointed, running jobs are requeued if the rerunable attribute is
true. Otherwise, jobs are killed. Normally the Server will not shutdown
until there are no jobs in the running state. If the Server is unable to
contact the MOM of running job, the job is still listed as running. The
Server may be forced down by a second ‘‘qterm -t immediate’’
If checkpoint is supported, running jobs that can be checkpointed are
checkpointed, terminated, and requeued. If a job cannot be checkpointed, but can be rerun, the job is terminated and requeued. Otherwise, running jobs are allowed to continue to run. Note, the operator or
administrator may use the qrerun and qdel commands to remove
running jobs.
This is the default action if the -t option is not specified. This option
is used when you wish that running jobs be left running when the
Server shuts down. The Server will cleanly shutdown and can be
restarted when desired. Upon restart of the Server, jobs that continue to
run are shown as running; jobs that terminated during the Server’s
absence will be placed into the exiting state.
Note that qterm now defaults to qterm -t quick. Also, note
that the Server now does a quick shutdown upon receiving SIGTERM.
148 Chapter 11
Should you ever have the need to stop a MOM daemon but
leave jobs managed by her running, the only way to do this is to
kill MOM with a SIGKILL (-9).
11.4 Checkpoint/Restart Under PBS
PBS Pro supports operating system level checkpoint-restart where provided by the system.
Currently both SGI IRIX and Cray UNICOS provide OS-level checkpoint packages,
which PBS uses. (User’s may optionally manage their own checkpointing from within
their application. This is discussed further in the PBS User Guide.)
11.4.1 Manually Checkpointing a Job
On systems which provide OS-level checkpointing, the PBS administrator may manually
force a running job to be checkpointed. This is done by using the qhold command. (discussed in detail in the PBS Users Guide).
11.4.2 Checkpointing Jobs During PBS Shutdown
As installed, the /etc/init.d/pbs script will not result in PBS checkpointing jobs
(on systems which provide OS-level checkpointing). This behavior allows for a faster shut
down of the batch system at the expense of rerunning jobs from the beginning. If you prefer jobs to be checkpointed, then append the -t immediate option to the qterm statement in the script.
11.4.3 Suspending/Checkpointing Multi-node Jobs
The PBS suspend/resume and checkpoint/restart capabilities now work for multi-node
jobs. With checkpoint (on systems which provide OS-level checkpointing), the system
must be able to save the complete session state in a file. This means any open socket will
cause the operation to fail. PBS normally sets up a socket connection to a process
(pbs_demux) which collects stdio streams from all tasks. If this is not turned off, the
checkpoint cannot work. Therefore, a new job attribute has been added:
no_stdio_sockets. See the pbs_job_attributes manual page for more
details. If this attribute is true, the pbs_demux process will not be started and no open
socket will prevent the checkpoint from working. The other place where PBS will use a
socket that must be addressed is if the program pbsdsh is used to spawn tasks. There is a
new option for pbsdsh '-o' that is used to prevent it from waiting for the spawned tasks
to finish. This is done so no socket will be left open to the MOM to receive task manager
events. If this is used, the shell must use some other method to wait for the tasks to finish.
PBS Pro 5.2 149
Administrator Guide
11.4.4 Checkpointing Jobs Prior to SGI IRIX Upgrade
Under the SGI Irix operating system, the normal checkpoint procedure does not save
shared libraries in the restart image in order to reduce the image size and time required to
write it. This type of image cannot be restarted following a Irix operating system upgrade.
In order to produce an image which can be restarted following an upgrade, a special flag is
required when calling checkpoint. With PBS Pro 5.2, pbs_mom has a new config file
option $checkpoint_upgrade which if present causes PBS to use the special
upgrade checkpoint flag. It is recommended that this flag be set (and pbs_mom be
restarted via SIGHUP) only when shutting down PBS just prior to upgrading your system.
11.5 Start/Stop/Enable/Disable Queues
In addition to the functionality offered by qmgr, PBS provides separate commands for
manipulating the status of queues. This section briefly describes the four commands. See
the corresponding manual pages for details of use.
The qstart command directs that a destination should process batch jobs. If the destination is an execution queue, the Server will begin to schedule jobs that reside in the queue
for execution. If the destination is a routing queue, the Server will begin to route jobs from
that queue
The qstop command directs that a destination should stop processing batch jobs. If the
destination is an execution queue, the Server will cease scheduling jobs that reside in the
queue for execution. If the destination is a routing queue, the Server will cease routing
jobs from that queue.
The qenable command directs that a destination should accept batch jobs. This command sends a Manage request to the batch Server specified on the command line. If the
command is accepted, the destination will accept Queue Job requests which specify the
The qdisable command directs that a destination should no longer accept batch jobs. If
the command is accepted, the destination will no longer accept Queue Job requests which
specified the disabled queue. Jobs which already reside in the queue will continue to be
processed. This allows a queue to be "drained."
150 Chapter 11
11.6 Security
There are three parts to security in the PBS system:
Internal security
Can the daemons be trusted?
How do we believe a client about who it is.
Is the client entitled to have the requested action performed.
11.7 Internal Security
A significant effort has been made to insure the various PBS daemon themselves cannot
be a target of opportunity in an attack on the system. The two major parts of this effort is
the security of files used by the daemons and the security of the daemons environment.
Any file used by PBS, especially files that specify configuration or other programs to be
run, must be secure. The files must be owned by root and in general cannot be writable by
anyone other than root.
A corrupted environment is another source of attack on a system. To prevent this type of
attack, each daemon resets its environment when it starts. The source of the environment
is a file named by PBS_ENVIRONMENT set by the configure option --set-environ, defaulting to PBS_HOME/pbs_environment. If it does not already exists, this
file is created during the install process. As built by the install process, it will contain a
very basic path and, if found in root’s environment, the following variables: TZ, LANG,
LC_TIME. The environment file may be edited to include the other variables
required on your system.
Please note that PATH must be included. This value of PATH
will be passed on to batch jobs. To maintain security, it is
important that PATH be restricted to known, safe directories.
Do NOT include “.” in PATH. Another variable which can be
dangerous and should not be set is IFS.
The entries in the PBS_ENVIRONMENT file can take two possible forms:
PBS Pro 5.2 151
Administrator Guide
In the later case, the value for the variable is obtained from the daemons environment
before the environment is reset.
11.7.1 Host Authentication
PBS uses a combination of information to authenticate a host. If a request is made from a
client whose socket is bound to a privileged port (less than 1024, which requires root privilege), PBS believes the IP (Internet Protocol) network layer as to whom the host is. If the
client request is from a non-privileged port, the name of the host which is making a client
request must be included in the credential sent with the request and it must match the IP
network layer opinion as to the host’s identity.
11.7.2 Host Authorization
Access to the Server from another system may be controlled by an access control list
Access to pbs_mom is controlled through a list of hosts specified in the pbs_mom’s configuration file. By default, only “localhost” and the name returned by gethostname(2)
are allowed. See the man pages pbs_mom(8B) for more information on the configuration
Access to pbs_sched is not limited other than it must be from a privileged port.
11.7.3 User Authentication
The PBS Server authenticates the user name included in a request using the supplied PBS
credential. This credential is supplied by pbs_iff.
11.7.4 User Authorization
PBS as shipped does not assume a consistent user name space within the set of systems
which make up a PBS cluster. However, the administrator can enable this assumption, if
desired. By default, the routine site_map_user() is called twice, once to map the
name of the requester and again to map the job owner to a name on the Server’s (local)
system. If the two mappings agree, the requester is considered the job owner.
If running PBS in an environment that does have a flat user namespace, the administrator
can disable these checks by setting the flatuid Server attribute to True via qmgr:
152 Chapter 11
# qmgr
Qmgr: set server flatuid=True
If flatuid is set to true, a UserA on HostX who submits a job to the PBS Server on
HostY will not require an entry in the /etc/passwd file, nor a .rhosts entry on HostY for
HostX, nor must HostX appear in HostY's /etc/hosts.equiv file.
In either case, if a job is submitted by UserA@hostA PBS will allow the job to be deleted
or altered by UserA@hostB
If flatuid is NOT set to true, a user may supply a name under which the job is to be
executed on a certain system. If one is not supplied, the name of the job owner is chosen to
be the execution name-- see the -u user_list option of the qsub(1B) command.
Authorization to execute the job under the chosen name is granted under the following
The job was submitted on the Server’s (local) host and the submitter’s name is the same as the selected execution name.
The host from which the job was submitted is declared trusted
by the execution host in the /etc/hosts.equiv file or the
submitting host and submitting user’s name are listed in the
execution users’ .rhosts file. The system supplied library
function, ruserok(), is used to make these checks.
If the above test to determine authorization are not sufficient to a site, the routine
site_check_user_map() in the file src/server/site_check_u.c may be
In addition to the above checks, access to a PBS Server and queues within that Server may
be controlled by access control lists. (For details see “Server Attributes” on page 66 and
“Queue Attributes” on page 72.)
11.7.5 Group Authorization
PBS allows a user to submit jobs and specify under which group the job should be executed. The user specifies a group_list attribute for the job which contains a list of
group@host similar to the user list. See the group_list attribute under the -W option
of qsub(1B). The PBS Server will ensure that the user is a member of the specified group
PBS Pro 5.2 153
Administrator Guide
Checking if the specified group is the user’s primary group in the
password entry on the execution host. In this case the user’s name
does not have to appear in the group entry for his primary group.
Checking on the execution host for the user’s name in the specified
group entry in /etc/group.
The job will be aborted if both checks fail. The checks are skipped if the user does not supply a group list attribute. In this case the user’s primary group from the password file will
be used.
When staging files in or out, PBS also uses the selected execution group for the copy operation. This provides normal UNIX access security to the files. Since all group information
is passed as a string of characters, PBS cannot determine if a numeric string is intended to
be a group name or GID. Therefore when a group list is specified by the user, PBS places
one requirement on the groups within a system: each and every group in which a user
might execute a job MUST have a group name and an entry in /etc/group. If no
group_list are ever used, PBS will use the login group and will accept it even if the
group is not listed in /etc/group. Note, in this latter case, the egroup attribute value
is a numeric string representing the GID rather than the group “name”.
11.8 External Security
In addition to the security measures discussed above, PBS provides three levels of privilege: user, operator, and Manager. Users have user privilege which allows them to manipulate their own jobs. Manager or Operator privilege is required to set or unset attributes of
the Server, queues, nodes, other peoples jobs, with the following exceptions:
Manager privilege is required to create and delete queues or nodes, and set/alter/unset:
node properties
server acl_host_enable
server acl_host_list
server acl_user_enable
server acl_users
server acl_roots
server managers
server operators
154 Chapter 11
server query_other_jobs
server comment
server default_node
server node_pack
11.9 Root Owned Jobs
The Server will reject any job which would execute under the UID of zero unless the
owner of the job, typically root on this or some other system, is listed in the Server
attribute acl_roots.
11.10 Managing PBS and Multi-node Parallel Jobs
Many customers use PBS Pro in cluster configurations for the purpose of managing multinode parallel applications. This sections provides the PBS administrator with information
specific to this situation.
11.10.1 Interfacing MPICH with PBS Pro
If you are running an open source version of MPI, such as MPICH, then the mpirun
command can be modified to check for the PBS environment and use the PBS supplied
host file.
In the case of MPICH, this is easily done by editing the .../mpich/bin/
mpirun.args file and adding the following near line 40 (depending on the version
being used):
if [ "$PBS_NODEFILE" != "" ]
Additional information regarding checkpointing of parallel jobs
is given in “Suspending/Checkpointing Multi-node Jobs” on
page 148.
PBS Pro 5.2 155
Administrator Guide
11.11 SGI Job Container / Limits Support
SGI Job Container/Limit support has been added to PBS Pro. Each PBS job is placed in its
own SGI Job container. Limits on the job are set as the MIN(ULDB limit, PBS
resource_list limit). The ULDB domains are set in the following order:
PBS_{queue name}
Limits are set for the following resources: "cput" and "vmem". A job limit is NOT set for
"mem" because the kernel does not factor in shared memory segments among sproc()
processes, thus the system report usage is too high.
11.12 Job Prologue/Epilogue Scripts
PBS provides the ability for the administrator run a site supplied script (or program)
before (prologue) and/or after (epilogue) each job runs. This provides the capability
to perform initialization or cleanup of resources, such as temporary directories or scratch
files. The scripts may also be used to write “banners” on the job’s output files. When multiple nodes are allocated to a job, these scripts are only run by the “Mother Superior”, the
pbs_mom on the first node allocated. This is also where the job shell script is run. Note
that both the prologue and epilogue are run with root privilege (not as the user), and neither are included in the job session, thus the prologue cannot be used to modify the job
environment or change limits on the job.
If a prologue or epilogue script is not present, MOM continues in a normal manner.
If present, the script is run with root privilege. In order to be run, the script must adhere to
the following rules:
The script must be in the /usr/spool/PBS/mom_priv directory with the name prologue for the script to be run before the
job and the name epilogue for the script to be run after the job.
The script must be owned by root.
The script must be readable and executable by root.
The script cannot be writable by anyone but root.
The “script” may be either a shell script or an executable object file. Typically, a shell
156 Chapter 11
script should start with a line of the form:
#! /path/interpreter
For more information, see the rules described under execve(2) or exec(2) on your system.
11.12.1 Prologue and Epilogue Arguments
When invoked, the prologue is called with the following arguments:
the job id.
the user name under which the job executes.
the group name under which the job executes.
The epilogue is called with the above, plus:
the job name.
the session id.
the requested resource limits (list).
the list of resources used
the name of the queue in which the job resides.
the account string, if one exists.
For both the prologue and epilogue:
The environment passed to the script is null.
The current working directory is the user’s home directory.
When invoked, both scripts have standard input connected to a
system dependent file. Currently, this file is /dev/null.
With one exception, the standard output and standard error of
the scripts are connected to the files which contain the standard
output and error of the job. If a job is an interactive PBS job, the
standard output and error of the epilogue is pointed to /dev/
null because the pseudo terminal connection used was
released by the system when the job terminated.
PBS Pro 5.2 157
Administrator Guide
11.12.2 Prologue Epilogue Time Out
To prevent an error condition within the prologue or epilogue from delaying PBS, MOM
places an alarm around the scripts execution. This is currently set to 30 seconds. If the
alarm sounds before the scripts has terminated, MOM will kill the script. The alarm value
can be changed by changing the define of PBS_PROLOG_TIME within src/resmom/prolog.c.
11.12.3 Prologue Error Processing
Normally, the prologue script should exit with a zero exit status. MOM will record in her
log any case of a non-zero exit from a script. Exit status values and their impact on the job
-4 The script timed out (took too long). The job will be requeued.
The wait(2) call waiting for the script to exit returned with an
error. The job will be requeued.
The input file to be passed to the script could not be opened. The job
will be requeued.
The script has a permission error, it is not owned by root and or is
writable by others than root. The job will be requeued.
The script was successful. The job will run.
The script returned an exit value of 1, the job will be aborted.
The script returned a value greater than one, the job will be
The above apply to normal batch jobs. Interactive-batch jobs (-I option) cannot be
requeued on a non-zero status. The network connection back to qsub is lost and cannot be
re-established. Interactive jobs will be aborted on any non-zero prologue exit.
The administrator must exercise great caution in setting up the prologue to prevent jobs from being flushed from the system.
Epilogue script exit values which are non-zero are logged, but have no impact on the state
of the job.
158 Chapter 11
11.13 Use and Maintenance of Logfiles
The PBS system tends to produce lots of logfile entries. There are two types of logfiles:
the event logs which record events from each PBS daemon (pbs_server, pbs_mom,
and pbs_sched) and the PBS accounting log.
11.13.1 PBS Events
The amount of output in the PBS event logfiles depends on the selected events to log (and
the presence of debug writes, turned on by compiling with -DDEBUG). All three PBS daemons can be directed to record only messages pertaining to certain event types. The specified events are logically “or-ed” to produce a mask representing the events the local site
wishes to have logged. The available events, and corresponding decimal and hexidecimal
values are show below.
Event Description
Internal PBS Errors.
System (OS) Errors, such as malloc failure.
Administrator related events, such as changing queue attributes.
Job related events: submitted, ran, deleted, ...
Job Resource Usage.
Security related events, such as attempts to connect from an
unknown host.
When the scheduler was called and why.
First level, common, debug messages.
Second level, more rare, debug messages.
Everything turned on is of course 511. 127 is a good value to use. The event logging mask
is controlled differently for the different daemons. The following table shows the log
event attribute for each daemon, and page reference for details.
PBS Pro 5.2 159
Administrator Guide
Attribute and Reference
See “log_events” on page 68.
Takes effect immediately with qmgr
See “$logevent” on page 97.
Requires SIGHUP to MOM
See “log_filter” on page 117.
Requires SIGHUP to Scheduler
11.13.2 The Event Logfiles
Each PBS daemon maintains separate event logfiles. The logfiles default to a file with the
current date as the name in the /usr/spool/PBS/(daemon)_logs directory. This
location can be overridden with the "-L pathname" option where pathname must be an
absolute path.
If the default logfile name is used (no -L option), the log will be closed and reopened with
the current date daily. This happens on the first message after midnight. If a path is given
with the -L option, the automatic close/reopen does not take place. All daemons will close
and reopen the same named log file on receipt of SIGHUP. The process identified (PID)
of the daemon is available in its lock file in its home directory. Thus it is possible to move
the current log file to a new name and send SIGHUP to restart the file:
# cd /usr/spool/PBS/DAEMON_logs
# mv current archive
# kill -HUP ‘cat ../DAEMON_priv/daemon.lock‘
11.13.3 Event Logfile Format
The daemon event logfile is a text file with each entry terminated by a new line. The format of an entry is:
The date-time field is a date and time stamp in the format:
mm/dd/yyyy hh:mm:ss.
160 Chapter 11
The event_code is the type of event which triggered the event logging. It corresponding to the bit position, 0 to n, in the event mask (discussed above) of the daemon writing
the event record.
The server_name is the name of the Server which logged the message. This is recorded
in case a site wishes to merge and sort the various logs in a single file.
The object_type is the type of object which the message is about:
for server
for queue
for job
for request
for file.
The object_name is the name of the specific object. message_text field is the text
of the log message.
11.13.4 The Accounting Log
The PBS Server daemon maintains an accounting log. The log name defaults to /usr/
spool/PBS/server_priv/accounting/yyyymmdd where yyyymmdd is the
date. The accounting log files may be placed elsewhere by specifying the -A option on the
pbs_server command line. The option argument is the full (absolute) path name of the
file to be used. If a null string is given, then the accounting log will not be opened and no
accounting records will be recorded. For example
# pbs_server -A ""
The accounting file is changed according to the same rules as the log files. If the default
file is used, named for the date, the file will be closed and a new one opened every day on
the first event (write to the file) after midnight. With either the default file or a file named
with the -A option, the Server will close the accounting log and reopen it upon the receipt
of a SIGHUP signal. This allows you to rename the old log and start recording again on
an empty file. For example, if the current date is February 9, 2001 the Server will be writing in the file 20010209. The following actions will cause the current accounting file to
be renamed feb9 and the Server to close the file and starting writing a new 20010209.
PBS Pro 5.2 161
Administrator Guide
# mv 20010209 feb9
# kill -HUP 1234
(the Server’s pid)
11.13.5 Accounting Log Format
The PBS accounting file is a text file with each entry terminated by a new line. The format
of an entry is:
date time;record_type;id_string;message_text
The date time field is a date and time stamp in the format:
mm/dd/yyyy hh:mm:ss
The id_string is the job, reservation, or reservation-job identifier. The
messge_text is ascii text. The content depends on the record type. The message text
format is blank separated keyword=value fields. The record_type is a single character indicating the type of record. The types are:
Job was aborted by the server.
Beginning of reservation’s period. The message_text field
contains details about the specified advance reservation. Possible attributes include
name of party who submitted the resources
reservation request.
if submitter supplied a name string for the
if submitter supplied a to be recorded in
162 Chapter 11
the name of the instantiated reservation
queue if this is a general resources reservation. If the resources reservation is for a
reservation job, this is the name of the
queue to which the reservation-job
time at which the resources reservation got
created, seconds since the epoch.
time at which the reservation period is to
start, in seconds since the epoch.
time at which the reservation period is to
end, seconds since the epoch.
the duration specified or computed for the
resources reservation, in seconds.
if nodes with specified properties are
required, this string is the allocated set.
the list of acl_users on the queue that is
instantiated to service the reservation.
if specified, the list of acl_groups on the
queue that is instantiated to service the reservation.
if specified, the list of acl_hosts on the
queue that is instantiated to service the reservation.
list of resources requested by the reservation. Resources are listed individually as,
for example: resource_list.ncpus=16
Job was checkpointed and held.
Job was deleted by request. The message_text will contain
requestor=user@host to identify who deleted the job.
PBS Pro 5.2 163
Administrator Guide
Job ended (terminated execution). The message_text field
contains detailed information about the job. Possible attributes
the user name under which the job executed.
the group name under which the job executed.
if job has an "account name" string.
the name of the job.
the name of the queue from which the job is
if job draws its resources from a resources
reservation and that reservation has a name.
if job draws its resources from a resources
if job is as a "reservation-job" (advance reservation of resources).
time in seconds when job was created (first
time in seconds when job was queued into
current queue.
time in seconds when job became eligible to
run; no holds, etc.
time in seconds when job execution started.
name of host on which the job is being executed.
list of the specified resource limits.
session number of job.
164 Chapter 11
Optional alternate job identifier. Included
only for certain systems: Irix 6.x with Array
Services - The alternate id is the Array Session Handle (ASH) assigned to the job.
time in seconds when job ended execution.
the exit status of the job. If the value is less
than 10000 (decimal) it is the exit value of
the top level process of the job, typically the
shell. If the value is greater than 10000, the
top process exited on a signal whose number
is given by subtracting 10000 from the exit
list of the specified resource limits.
Resources reservation period finished.
Scheduler or server requested removal of the reservation. The
message_text field contains: requestor=user@host
to identify who deleted the resources reservation.
Resources reservation terminated by ordinary client - e.g. an
owner issuing a pbs_rdel command. The message_text
field contains: requestor=user@host to identify who
deleted the resources reservation.
Job entered a queue. The message_text contains queue=name
identifying the queue into which the job was placed. There will
be a new Q record each time the job is routed or moved to a new
(or the same) queue.
Job was rerun.
Job execution started. The message_text field contains:
PBS Pro 5.2 165
Administrator Guide
the user name under which the job executed.
the group name under which the job executed.
the name of the job.
the name of the queue from which the job is executed.
time in seconds when job was created (first submitted).
time in seconds when job was queued into current queue.
time in seconds when job became eligible to run;
no holds, etc.
time in seconds when job execution started.
name of host on which the job is being executed.
list of the specified resource limits.
session number of job.
Job was restarted from a checkpoint file.
Created unconfirmed resources reservation on Server. The
message_text field contains requestor=user@host to
identify who requested the resources reservation.
Resources reservation confirmed by the scheduler. The
message_text field contains the same item (items) as in a U
record type.
For Resource_List and Resources_used, there is one entry per resource.
166 Chapter 11
11.14 Interpreting PBS Exit Codes
The PBS Server logs and accounting logs record an “exit status” of jobs. Zero or positive
exit status is the status of the top level shell. Certain negative exit status are used internally
and will never be reported to the user. The positive exit status values indicate which signal
killed the job. Depending on the system, values greater than 128 (or on some systems 256,
see wait(2) or waitpid(2) for more information) are the value of the signal that killed the
job. To interpret (or “decode”) the signal contained in the exit status value, subtract the
base value from the exit status. For example, if a job had an exit status of 143, that indicates the jobs was killed via a SIGTERM (e.g. 143 - 128 = 15, signal 15 is SIGTERM).
See the kill(1) manual page for a mapping of signal numbers to signal name on your operating system.
11.15 PBS tracejob Command
PBS includes tracejob utility to extract log messages for a particular job (from all log
files available on the local host) and print them sorted into chronological order. Usage for
the tracejob command is:
tracejob [-a|s|l|m|v] [-w size] [-p path] [-n days] [-f filter]
The available options, and description of each follows.
Don't use accounting log files
What message count is considered excessive
Filter out types of log entries, multiple -f's can be specified error,
system, admin, job, job_usage, security, sched, debug, debug2, or
absolute numeric equiv
Don't use scheduler log files
Don't use mom log files
Number of days in the past to look for job(s) [default 1]
Don't use server log files
PBS Pro 5.2 167
Administrator Guide
Number of columns of your terminal
Verbose mode - show more error messages
Toggle filtering excessive messages
Following example request all log message for a particular job from today’s (the default
date) log file.
% tracejob 475
Job: 475.riverside.pbspro.com
03/10/2002 14:29:15 S enqueuing into workq, state 1 hop 1
03/10/2002 14:29:15 S Job Queued at request of jjones, owner =
jjones@mars.pbspro.com, job name = STDIN
03/10/2002 15:06:30 S Job Modified at request of Scheduler
03/10/2002 15:06:30 L Considering job to run
03/10/2002 15:06:30 S Job Run at request of Scheduler
03/10/2002 15:06:32 L Job run on node mars
03/10/2002 15:06:32 M Started, pid = 25282
03/10/2002 15:06:32 M Terminated
03/10/2002 15:06:32 M task 1 terminated
03/10/2002 15:06:32 M kill_job
03/10/2002 15:06:32 S Obit received
03/10/2002 15:06:32 S dequeuing from workq, state 5
03/10/2002 15:06:32 S Exit_status=0
Note that third column of the body of the display contains a single letter abbreviation (S,
M, A, or L) which corresponds to the source of the log message (Server, MOM, Accounting, or Local-policy Scheduler log files).
168 Chapter 11
11.16 Handling Jobs on Failed Nodes
If a job is running and the first node assigned to the job goes down, the job can be requeued (qrerun) or deleted (qdel). Neither of these actions are performed automatically because (1) it might be the network rather than the node that actually went down and
the job is still running correctly, or (2) it might be that the pbs_mom on the node went
down and the job is still running correctly. In either case, rather than waste the cycles
spent so far, the administrator or user can allow the job to continue and when the network
or pbs_mom is restarted, the work will not have been lost.
However, if the node is truly down, the administrator or user can delete the job or requeue
it for execution later, by using the “-W force” option to qdel and qrerun, as shown
Note, in either case, the output created by the job before the
node went down will be discarded.
% qdel -W force 1123.veridian.com
% qrerun -W force 1124.veridian.com
11.17 xPBS GUI Configuration
PBS currently provides two Graphical User Interfaces (GUIs): xpbs (intended primarily
for users) and xpbsmon (intended for PBS operators and managers). Both are built using
the Tool Control Language Toolkit (TCL/tk). The first section below discusses the user
GUI, xpbs. The following section discusses xpbsmon.
11.17.1 xpbs
xpbs provides a user-friendly point-and-click interface to the PBS commands. To run
xpbs as a regular, non-privileged user, type:
% setenv DISPLAY your_workstation_name:0
% xpbs
PBS Pro 5.2 169
Administrator Guide
To run xpbs with the additional purpose of terminating PBS Servers, stopping and starting queues, or running/rerunning jobs, then run:
% xpbs -admin
Running xpbs will initialize the X resource database from various sources in the following order:
The RESOURCE_MANAGER property on the root window
(updated via xrdb) with settings usually defined in the .Xdefaults file
170 Chapter 11
Preference settings defined by the system administrator in the
global xpbsrc file
User’s ~/.xpbsrc file-- this file defines various X resources
like fonts, colors, list of PBS hosts to query, criteria for listing
queues and jobs, and various view states.
The system administrator can specify a global resources file to be read by the GUI if a personal .xpbsrc file is missing: /usr/pbs/lib/xpbs/xpbsrc. Keep in mind that
within an Xresources file (Tk only), later entries take precedence. For example, suppose in
your .xpbsrc file, the following entries appear in order:
xpbsrc*backgroundColor: blue
*backgroundColor: green
The later entry "green" will take precedence even though the first one is more precise and
longer matching. The things that can be set in the personal preferences file are fonts, colors, and favorite Server host(s) to query.
xpbs usage, command correlation, and further customization information is provided in
the PBS Pro User Guide, Chapter 5, “Using the xpbs GUI”.
11.18 xpbsmon GUI Configuration
xpbsmon is the node monitoring GUI for PBS. It is used for graphically displaying information about execution hosts in a PBS environment. Its view of a PBS environment consists of a list of sites where each site runs one or more Servers, and each Server runs jobs
on one or more execution hosts (nodes).
The system administrator needs to define the site’s information in a global X resources
file, /usr/pbs/lib/xpbsmon/xpbsmonrc which is read by the GUI if a personal
.xpbsmonrc file is missing. A default xpbsmonrc file usually would have been created already during installation, defining (under *sitesInfo resource) a default site name,
list of Servers that run on a site, set of nodes (or execution hosts) where jobs on a particular Server run, and the list of queries that are communicated to each node’s pbs_mom. If
node queries have been specified, the host where xpbsmon is running must have been
given explicit permission by the pbs_mom daemon to post queries to it. This is done by
including a $restricted entry in the MOM’s config file.
PBS Pro 5.2 171
Administrator Guide
It is not recommended to manually update the *sitesInfo value in the xpbsmonrc file as
its syntax is quite cumbersome. The recommended procedure is to bring up xpbsmon,
click on "Pref.." button, manipulate the widgets in the Sites, Server, and Query Table dialog boxes, then click "Close" button and save the settings to a .xpbsmonrc file. Then
copy this file over to the /usr/pbs/lib/xpbsmon/ directory.
11.19 pbsnodes Command
The pbsnodes command is used to query the status of nodes, or mark nodes down, free
or off-line. Node information is obtained by sending a request to the PBS Server.
pbsnodes Usage
(no option)
Prints the command usage syntax
node1 node2
Prints the status of nodes node1 and node2
172 Chapter 11
pbsnodes Usage
-d node1
The nodes specified as operands are marked DOWN and unavailable to run jobs. It is important that all the nodes known to be
down are given as arguments on the command line. This is
because nodes which are not listed are assumed to be UP and will
be indicated as such if they were previously marked DOWN. I.e.,
"pbsnodes -d" will mark all nodes as free.
-c node2
All nodes and all their attributes are listed.
Clear OFFLINE or DOWN from listed nodes. The listed nodes
are "free" to be allocated to jobs.
List all nodes marked in any way.
-o node3
Mark listed nodes as OFFLINE even if currently in use. This is
different from being marked DOWN. An automated script that
checks nodes being up or down and calls pbsnodes with a list
of nodes down will not change the status of nodes marked
OFFLINE. This gives the administrator a tool to hold a node out
of service without changing the automatic script.
-r node3
Clear OFFLINE from listed nodes.
Specify the PBS Server to which to connect.
Only the -d option will change the marking for nodes which
are not given on the command line.
11.20 Using Job Comments
Users tend to want to know what is happening to their job. PBS provides a special job
attribute, comment which is available to the operator, manager, or the Scheduler program. This attribute can be set to a string to pass information to the job owner. It might be
used to display information about why the job is not being run or why a hold was placed
on the job. Users are able to see this attribute, when set, by using the -f and -s option
of the qstat command. (For details see “Job Comments” in the PBS User Guide.) Operators and managers may use the -W option of the qalter command, for example
qalter -W comment="some text" job_id
PBS Pro 5.2 173
Administrator Guide
11.21 PBS Pro on Scyld Beowulf Clusters
Running PBS Pro under Scyld Computing Corporation’s Beowulf operating system is a
bit different from normal clusters. Given Scyld’s single system image, there needs to be
only a single MOM running within the cluster, rather than on each node. When pbs_mom
starts on the master node, the ownership of all the compute nodes is changed to 'root'. Each
time a job runs, the ownership of the nodes chosen for the job will be changed to the user
running the job.
The Scyld kernel allows processes running on the compute nodes to be tracked on the
master node so pbs_mom can directly set limits and track usage. The ncpus resource is
reported as the total number of CPUs reported on all the compute nodes configured. The
actual number of CPUs available will vary as nodes run jobs, go down or otherwise
become unavailable. Since ownership is assigned on a node rather than cpu basis, if you
have multi-cpu nodes, there may be unused CPUs if a job asks for a number of nodes that
is not an even multiple of the number of CPUs per node. The physmem resource is the
sum of physical memory on all the compute nodes.
Information on running jobs on Scyld Beowulf clusters is given in section “Running Jobs
on Scyld Beowulf Clusters” of the PBS User Guide.
PBS Pro 5.2 174
Administrator Guide
PBS Pro 5.2 175
Administrator Guide
Chapter 12
Problem Solving
The following is a list of common problems and recommended solutions. Additional
information is always available online at the PBS website, www.pbspro.com. The last section in this chapter gives important information on how to get additional assistance from
the PBS Support staff.
12.1 Clients Unable to Contact Server
If a client command (such as qstat or qmgr) is unable to connect to a Server there are
several possibilities to check. If the error return is 15034, “No server to connect
to”, check (1) that there is indeed a Server running and (2) that the default Server information is set correctly. The client commands will attempt to connect to the Server specified on the command line if given, or if not given, the Server specified by SERVER_NAME
in /etc/pbs.conf.
If the error return is 15007, “No permission”, check for (2) as above. Also check
that the executable pbs_iff is located in the search path for the client and that it is setuid root. Additionally, try running pbs_iff by typing:
pbs_iff -t server_host 15001
Where server_host is the name of the host on which the Server is running and 15001
176 Chapter 12
Problem Solving
is the port to which the Server is listening (if started with a different port number, use that
number instead of 15001). Check for an error message and/or a non-zero exit status. If
pbs_iff exits with no error and a non-zero status, either the Server is not running or was
installed with a different encryption system than was pbs_iff.
12.2 Nodes Down
The PBS Server determines the state of nodes (up or down), by communicating with
MOM on the node. The state of nodes may be listed by two commands: qmgr and pbsnodes.
% qmgr
Qmgr: list node @active
% pbsnodes -a
Node jupiter
state = down, state-unknown
properties = sparc, mine
ntype = cluster
A node in PBS may be marked “down” in one of two substates. For example, the state
above of node “jupiter” shows that the Server has not had contact with MOM since the
Server came up. Check to see if a MOM is running on the node. If there is a MOM and if
the MOM was just started, the Server may have attempted to poll her before she was up.
The Server should see her during the next polling cycle in 10 minutes. If the node is still
marked “down, state-unknown” after 10+ minutes, either the node name specified
in the Server’s node file does not map to the real network hostname or there is a network
problem between the Server’s host and the node.
If the node is listed as
% pbsnodes -a
Node jupiter
state = down
properties = sparc, mine
ntype = cluster
Then the Server has been able to ping MOM on the node in the past, but she has not
responded recently. The Server will send a “ping” PBS message to every free node each
ping cycle, 10 minutes. If a node does not acknowledge the ping before the next cycle,
the Server will mark the node down.
PBS Pro 5.2 177
Administrator Guide
On an IBM SP, a node may also be marked down if MOM on the node believes that the
node is not connected to the high speed switch. When the Server receives an acknowledgment from MOM on the node, the node will again be marked up (free).
12.3 Requeueing a Job “Stuck” on a Down Node
Once a job is "running" it will be in that state until the Server hears otherwise from MOM.
However, if the (first) node for a job fails/crashes/hangs, then MOM cannot tell the Server
that the job is done. You have two options of how to handle this situation.
If you wish to have PBS simply remove the hung job from the system, use the “Wforce” option to qdel:
% qdel -Wforce jobID
If instead you want PBS to requeue the job, and have it immediately eligible to run again,
use the “-Wforce” option to qrerun:
% qrerun -Wforce jobID
The -Wforce option is required as a safe-guard since both actions are extraordinary.
12.4 Non Delivery of Output
If the output of a job cannot be delivered to the user, it is saved in a special directory:
/usr/spool/PBS/undelivered and mail is sent to the user. The typical causes of
non-delivery are:
1. The destination host is not trusted and the user does not have a .rhosts file.
2. An improper path was specified.
3. A directory in the specified destination path is not writable.
4. The user’s .cshrc on the destination host generates output when executed.
5. The path specified by PBS_SCP in /etc/pbs.conf is incorrect.
6.The /usr/spool/PBS/spool directory on the execution host does not have the
correct permissions. This directory must have mode 1777 (drwxrwxrwxt).
These are explained in the “Delivery of Output Files” section of the PBS User Guide.
178 Chapter 12
Problem Solving
12.5 Job Cannot be Executed
If a user receives a mail message containing a job id and the line “Job cannot be
executed”, the job was aborted by MOM when she tried to place it into execution. The
complete reason can be found in one of two places, MOM’s log file or the standard error
file of the user’s job.
If the second line of the message is “See Administrator for help”, then MOM
aborted the job before the job’s files were set up. The reason will be noted in MOM’s log.
Typical reasons are a bad user/group account, checkpoint/restart file (Cray or SGI), or a
system error.
If the second line of the message is “See job standard error file”, then MOM
had created the job’s file and additional messages were written to standard error. This is
typically the result of a bad resource request.
12.6 Running Jobs with No Active Processes
On very rare occasions, PBS may be in a situation where a job is in the Running state but
has no active processes. This should never happen as the death of the job’s shell should
trigger MOM to notify the Server that the job exited and end of job processing should
begin. If this situation is noted, PBS offers a way out. Use the qsig command to send
SIGNULL, signal 0, to the job. If MOM finds there are no processes then she will force
the job into the exiting state.
12.7 Getting Help
If the material in the PBS manuals is unable to help you solve a particular problem, you
may need to contact the PBS Support team for assistance. First, be sure to check the Customer Login area of the PBS Pro website, which has a number of ways to assist you in
resolving problems with PBS. The two most frequently used are: the Tips & Advice page
and the Submit Problem Report page.
The PBS Pro support team can also be reached directly via email and phone (contact information on the inside front cover of this manual).
When contacting PBS Pro Support, please provide as much of
the following information as possible:
PBS Pro 5.2 179
Administrator Guide
Output of the following commands:
qstat -Bf
qstat -Qf
pbsnodes -a
If the question pertains to a certain type of job, include:
qstat -f job_id
If the question is about scheduling, also send your:
(PBS_HOME)/sched_priv/sched_config file.
To expand, renew, or change your PBS support contract, contact our Sales Department.
(See contact information on the inside front cover of this manual.)
180 Chapter 12
Problem Solving
PBS Pro 5.2 181
Administrator Guide
Chapter 13
Customizing PBS
This chapter addresses several ways that PBS can be customized for your site. While having the source code is the first step, there are specific actions other than modifying the
code you can take.
13.1 Shell Invocation
When PBS starts a job, it invokes the user’s login shell (unless the user submitted the job
with the -S option). PBS passes the job script which is a shell script to the login process in
one of two ways depending on how PBS was installed.
Name of Script on Standard Input
The default method (PBS built with --enable-shell-pipe) is to pass
the name of the job script to the shell program. This is equivalent to
typing the script name as a command to an interactive shell. Since
this is the only line passed to the script, standard input will be empty
to any commands. This approach offers both advantages and disadvantages:
Any command which reads from standard input without redirection
will get an EOF.
The shell syntax can vary from script to script, it does not have to
match the syntax for the user’s login shell. The first line of the
182 Chapter 13
Customizing PBS
script, even before any #PBS directives, should be
#!/shell where shell is the full path to the shell of choice,
/bin/sh, /bin/csh, ...
The login shell will interpret the #! line and invoke that shell to
process the script.
An extra shell process is run to process the job script.
If the script does not include a #! line as the first line, the
wrong shell may attempt to interpret the script producing syntax
If a non-standard shell is used via the -S option, it will not
receive the script, but its name, on its standard input.
Script as Standard Input
The alternative method for PBS (built with --disableshell-invoke), is to open the script file as standard input
for the shell. This is equivalent to typing:
% /path/shell < script
This also offers advantages and disadvantages:
The user’s script will always be directly processed by the user’s
login shell.
If the user specifies a non-standard shell (any old program) with
the -S option, the script can be read by that program as its input.
If a command within the job script reads from standard input, it
may read lines from the script depending on how far ahead the
shell has buffered its input. Any command line so read will not
be executed by the shell. A command that reads from standard
input with out explicit redirection is generally unwise in a batch
The choice of shell invocation methods is left to the site. It is recommended that all PBS
execution servers (pbs_mom) within that site be built to use the same shell invocation
PBS Pro 5.2 183
Administrator Guide
13.2 Additional Build Options
Two header files within the subdirectory src/include provide additional configuration
control over the Server and MOM. The modification of any symbols in the two files
should not be undertaken lightly.
13.2.1 pbs_ifl.h
This header file contains structures, symbols and constants used by the API, libpbs.a, and
the various commands as well as the daemons. Very little here should ever be changed.
Possible exceptions are the following symbols. They must be consistent between all batch
systems which might interconnect.
Defines the length of the maximum possible host name. This should
be set at least as large as MAXHOSTNAME which may be defined
in sys/params.h.
Defines the maximum possible length of a user login name.
Defines the maximum possible length of a maximum possible group
Defines the maximum possible length of a maximum possible PBS
queue name.
If this symbol is set to zero (0), before the library and commands are
built, the API routine pbs_connect() will not attempt to invoke
the program pbs_iff to generate a secure credential to authenticate the user. Instead, a clear text credential will be generated. This
credential is completely subject to forgery and is useful only for
debugging the PBS system. You are strongly advised against using a
clear text credential.
Defines the port number at which the Server listens.
184 Chapter 13
Customizing PBS
Defines the port number at which MOM, the execution miniserver, listens.
Defines the port number at which the Scheduler listens.
13.2.2 server_limits.h
This header file contains symbol definitions used by the Server and by MOM. Only those
that might be changed are listed here. These should be changed with care. It is strongly
recommended that no other symbols in server_limits.h be changed. If
server_limits.h is to be changed, it may be copied into the include directory of the target
(build) tree and modified before compiling.
If defined, directs MOM to not use a spool directory for the job
output, but to place it in the user’s home directory while the job
is running. This allows a site to invoke quota control over the
output of running batch jobs.
This is the service name used by the Server to determine to
which port number it should listen. It is set to pbs in quotes as
it is a character string. Should you wish to assign PBS a service port in /etc/services change this string to the service
Defined to the name of the default administrator, typically
“root”. Generally only changed to simplify debugging.
Set to user name from which mail will be sent by PBS. The
default is "adm". This is overridden if the Server attribute
mail_from is set.
The length of the job id string used as the basename for job
associated files stored in the spool directory. It is set to 11,
which is 14 minus the 3 characters of the suffixes like .JB and
.OU. Fourteen is the guaranteed length for a file name under
PBS Pro 5.2 185
Administrator Guide
Used to limit the number of hops taken when being routed from
queue to queue. It is mainly to detect loops.
The maximum number of open file descriptors and sockets supported by the Server.
The limit on retrying requests to remote Servers.
The time between network routing retries to remote queues and for
requests between the Server and MOM.
To refrain from over burdening any given MOM, the Server will
wait this amount of time (default 30 seconds) between asking her
for updates on running jobs. In other words, if a user asks for status
of a running job more often than this value, the prior data will be
If defined (set to 1), “root” is an administrator of the batch system
even if not listed in the managers attribute.
The default value for the elapsed time between scheduling cycles
with no change in jobs queued. This is the initial value used by the
Server, but it can be changed via qmgr(1B).
13.3 Site Modifiable Source Files
It is safe to skip this section until you have played with PBS for a while and want to start
Certain functions of PBS appear to be likely targets of widespread modification by sites
for a number of reasons. When identified, the developers of PBS have attempted to
improve the easy of modification in these areas by the inclusion of special site specific
modification routines The distributed default version of these files build a private library,
libsite.a, which is included in the linking phase for the Server and for MOM.
186 Chapter 13
Customizing PBS
13.3.1 Server Modifiable Files
The routine in this file, site_allow_u() provides an additional point at which a user can be denied access to the batch
system (Server). It may be used instead of or in addition to the
Server acl_user list.
The function site_alt_router() allows a site to add decision capabilities to job routing. This function is called on a perqueue basis if the queue attribute alt_router is true. As provided, site_alt_router() just invokes the default router,
There are two routines in this file.
The routine site_check_user_map() provides the service
of authenticating that the job owner is privileged to run the job
under the user name specified or selected for execution on the
Server system.
The routine site_acl_check() provides the site with the
ability to restrict entry into a queue in ways not otherwise covered. For example, you may wish to check a bank account to see
if the user has the funds to run a job in the specific queue.
For sites without a common user name/uid space, this function,
site_map_user() provides a place to add a user name mapping function. The mapping occurs at two times. First to determine if a user making a request against a job is the job owner,
see “User Authorization”. Second, to map the submitting user
(job owner) to an execution uid on the local machine.
These files provide a site with the ability to add local attributes
to the Server, queues, and jobs. The files are installed into the
target tree “include” subdirectory during the first make. As
delivered, they contain only comments. If a site wishes to add
attributes, these files can be carefully modified.
The files are in three groups, by Server, queue, and job. In each
group are site_*_attr_def.h files which are used to
defined the name and support functions for the new attribute or
attributes, and site_*_attr_enum.h files which insert a
enumerated label into the set for the corresponding parent
object. For Server, queue, node attributes, there is also an addi-
PBS Pro 5.2 187
Administrator Guide
tional file that defines if the qmgr(1) command will include the
new attribute in the set “printed” with the print server,
print queue, or print nodes sub-commands.
This file allows a site to add local resources. It is included into the
Server’s resc_def_all.c file at compile time.
You should note that just adding attributes will have no effect on
how PBS processes jobs. The main usage for new attributes would
be in providing new Scheduler controls and/or information. The
scheduling algorithm will have to be modified to use the new
attributes. If you need MOM to do something different with a job,
you will still need “to get down and dirty” with her source code.
13.3.2 MOM Modifiable Files
If a Server is sending jobs to more than one MOM, additional
checking for execution privilege may be required at MOM’s level. It
can be added in this function site_mom_chkuser().
Provide post-checkpoint, site_mom_postchk() and pre-restart
site_mom_prerst() “user exits” for the Cray and SGI systems.
The function site_job_setup() allows a site to perform specific actions once the job session has been created and before the
job runs.
13.4 Implementing a Custom Scheduler
PBS provides a separate process to determine which jobs should be placed into execution.
This is a flexible mechanism by which you may implement a very wide variety of policies.
The Scheduler uses the standard PBS API to communicate with the Server and an additional API to communicate with the PBS resource monitor, pbs_mom. Should the provided Schedulers be insufficient to meet your site’s needs, it is possible to implement a
replacement Scheduler using the provided APIs which will enforce the desired policies.
188 Chapter 13
Customizing PBS
13.4.1 Scheduling Theory
The first generation UNIX batch system, NQS, and many of the other workload management systems use various queue-based controls to limit or schedule jobs. Queues would be
turned on and off to control job ordering over time or have a limit of the number of running jobs in the queue. While PBS supports multiple queues and the queues have some of
the “job scheduling” attributes used by other batch systems, the PBS Server does not by
itself run jobs or enforce any of the restrictions implied by these queue attributes. In fact,
the Server will happily run a held job that resides in a stopped queue with a zero limit on
running jobs, if it is directed to do so. The direction may come from the operator, administrator, or the Scheduler. In fact, the Scheduler is nothing more than a client with administrator privilege.
If you chose to implement your site scheduling policy using a multiple-queue queue-based
scheme, you may do so. The Server and queue attributes used to control job scheduling
may be adjusted by a client with privilege, such as qmgr(8B), or by a program of your
own creation. However, the controls are actually used by in the Scheduler, not the Server.
The Scheduler must check the status of the Server and queues, as well as the jobs, determining the setting of the Server and queue controls. It then must use the settings of those
controls in its decision making. Another possibility is the “whole pool” approach, wherein
all jobs are in a single pool (single queue). The Scheduler evaluates each job on its merits
and decides which, if any, to run. The policy can easily include factors such as time of day,
system load, size of job, etc. Ordering of jobs in the queue need not be considered. The
PBS team believes that this approach is superior for two reasons:
Users are not tempted to lie about their requirements in order to
“game” the queue policy.
The scheduling can be performed against the complete set of
current jobs resulting in better fits against the available
13.4.2 Scheduler – Server Interaction
In developing a scheduling policy, it may be important to understand when and how the
Server and the Scheduler interact. The Server always initiates the scheduling cycle. When
scheduling is active within the Server, the Server opens a connection to the Scheduler and
sends a command indicating the reason for the scheduling cycle. The reasons or events
that trigger a cycle are defined in include/sched_cmd.h. A description of each follows.
PBS Pro 5.2 189
Administrator Guide
A job newly becomes eligible to execute. The job may be a new
job in an execution queue, or a job in an execution queue that
just changed state from held or waiting to queued.
An executing job terminates.
The time interval since the prior cycle specified by the Server
attribute schedule_iteration is reached.
The Server attribute scheduling is set or reset to true. If set
true, even if it’s previous value was true, the Scheduler will be
cycled. This provides the administrator/operator a means to
force a scheduling cycle.
If the Scheduler was cycled and it requested one and only one
job to be run, then the Scheduler will be recycled by the Server.
This event is a bit abstruse. It exists to “simplify” a Scheduler.
The Scheduler only need worry about choosing the one best job
per cycle. If other jobs can also be run, it will get another
chance to pick the next job. Should a Scheduler run none or
more than one job in a cycle it is clear that it need not be
recalled until conditions change and one of the other events
trigger the next cycle.
If the Server recently recovered, the first scheduling cycle,
resulting from any of the above, will be indicated uniquely.
Once the Server has contacted the Scheduler and sent the reason for the contact, the
Scheduler then becomes a privileged client of the Server. As such, it may command the
Server to perform any action allowed to a Manager.
When the Scheduler has completed all activities it wishes to perform in this cycle, it will
close the connection to the Server. While a connection is open, the Server will not attempt
to open a new connection.
Note that the Server contacts the Scheduler to begin a scheduling cycle only if scheduling
is active in the Server. This is controlled by the value of the Server attribute schedul-
190 Chapter 13
Customizing PBS
ing. If set true, scheduling is active and qstat -B will show the Server status as
Active. If scheduling is set false, then the Server will not contact the Scheduler and
the Server’s status is shown as Idle. When started, the Server will recover the value for
scheduling as it was set when the Server shut down. The value may be changed in
two ways: the -a option on the pbs_server command line, or by setting scheduling to
true or false via qmgr.
One point should be clarified about job ordering: Queues “are” and “are not” FIFOs. What
is meant is that while jobs are ordered first in – first out in the Server and in each queue.
That fact does not imply that running them in that order is mandated, required, or even
desirable. That is a decision left completely up to site policy and implementation. The
Server will maintain the order across restarts solely as a aid to sites that wish to use a FIFO
ordering in some fashion.
13.4.3 Creating a New Scheduler
PBS provides two different interfaces for creating custom scheduler modules: the C programming language, and the Tool Command Language (TCL). This sections gives a highlevel overview of each. For detailed information, consult the PBS External Reference
13.4.4 Tcl-Based Scheduling
The provided Tcl based Scheduler framework uses the basic Tcl interpreter with some
extra commands for communicating with the PBS Server and Resource Monitor. The
scheduling policy is defined by a script written in Tcl. A number of sample scripts are provided in the source directory src/scheduler.tcl/sample_scripts. The Tcl
based Scheduler works, very generally, as follows:
On start up, the Scheduler reads the initialization script (if specified with the -i option) and executes it. Then, the body script is
read into memory. This is the file that will be executed each
time a “schedule” command is received from the Server. It then
waits for a “schedule” command from the Server.
When a schedule command is received, the body script is executed. No special processing is done for the script except to provide a connection to the Server. A typical script will need to
retrieve information for candidate jobs to run from the Server
using pbsselstat or pbsstatjob. Other information
from the Resource Monitor(s) will need to be retrieved by opening connections with openrm(3B) and submitting queries with
PBS Pro 5.2 191
Administrator Guide
addreq(3B) and getting the results with getreq(3B). The
Resource Monitor connections must be closed explicitly with
closerm(3B) or the Scheduler will eventually run out of file
descriptors. When a decision is made to run a job, a call to
pbsrunjob(3B) must be made.
When the script evaluation is complete, the Scheduler will close
the TCP/IP connection to the Server.
13.4.5 Tcl-Based Scheduling Advice
The Scheduler does not restart the Tcl interpreter for each cycle. This gives the ability to
carry information from one cycle to the next. It also can cause problems if variables are
not initialized or "unset" at the beginning of the script when they are not expected to contain any information later on.
System load average is frequently used by a script. This number is obtained from the system kernel by pbs_mom. Most systems smooth the load average number over a time
period. If one scheduling cycle runs one or more jobs and the next scheduling cycle occurs
quickly, the impact of the newly run jobs will likely not be reflected in the load average.
This can cause the load average to shoot way up especially when first starting the batch
system. Also when jobs terminate, the delay in lowering the load average may delay the
scheduling of additional jobs. The Scheduler redirects the output from “stdout” and
“stderr” to a file. This makes it easy to generate debug output to check what your script is
doing. It is advisable to use this feature heavily until you are fairly sure that your script is
working well.
13.4.6 Implementing a Tcl Scheduler
The best advice is study the examples found in src/scheduler.tcl/sample_scripts. Then
once you have modified or written a Scheduler body script and optionally an initialization
script, place them in the directory /usr/spool/PBS/sched_priv and invoke the
Scheduler by typing:
pbs_sched [-b script] [-i init_script]
See the pbs_sched_tcl(8B) man page for more information.
192 Chapter 13
Customizing PBS
13.4.7 C-Based Scheduling
The C based Scheduler is similar in structure and operation to the Tcl Scheduler except
that C functions are used rather than Tcl scripts:
On start up, the Scheduler calls schedinit(argc, argv)
one time only to initialize whatever is required to be initialized.
When a schedule command is received, the function schedule(cmd, connector) is invoked. All scheduling activities
occur within that function. The values of cmd are discussed in
“Scheduler – Server Interaction” on page 188.
Upon return to the main loop, the connection to the Server is
Several working Scheduler code examples are provided in the samples subdirectory. The
following sections discuss certain of the sample schedulers including the default Scheduler Standard. The sources for the samples are found in src/scheduler.cc/samples under the scheduler type name, for example src/scheduler.cc/samples/
13.4.8 Scheduling and File Staging
A decision must be made about when to begin to stage-in files for a job. The files must be
available before the job executes. The amount of time that will be required to copy the
files is unknown to PBS, that being a function of file size and network speed. If file instaging is not started until the job has been selected to run when the other required
resources are available, either those resources are “wasted” while the stage-in occurs, or
another job is started which takes the resources away from the first job, and might prevent
it from running. If the files are staged in well before the job is otherwise ready to run, the
files may take up valuable disk space need by running jobs.
PBS provides two ways that file in-staging can be initiated for a job. If a run request is
received for a job with a requirement to stage in files, the staging operation is begun and
when completed, the job is run. Or, a specific stage-in request may be received for a job,
see pbs_stagein(3B), in which case the files are staged in but the job is not run. When
the job is run, it begins execution immediately because the files are already there.
In either case, if the files could not be staged-in for any reason, the job is placed into a wait
state with a “execute at” time PBS_STAGEFAIL_WAIT 30 minutes in the future. A
mail message is sent to the job owner requesting that s/he look into the problem. The rea-
PBS Pro 5.2 193
Administrator Guide
son the job is changed into wait state is to prevent the Scheduler from constantly retrying
the same job which likely would keep on failing.
Figure 5.0 in Appendix B of the PBS ERS shows the (sub)state changes for a job involving file in staging. The Scheduler may note the substate of the job and chose to perform
pre-staging via the pbs_stagein() call. The substate will also indicate completeness or failure of the operation. The Scheduler developer should carefully chose a stage-in approach
based on factors such as the likely source of the files, network speed, and disk capacity.
194 Chapter 13
Customizing PBS
PBS Pro 5.2 195
Administrator Guide
Appendix A: Error Codes
The following table lists all the PBS error codes, their textual names, and a description of
Error Name
Error Code
No error
Unknown Job Identifier
Undefined Attribute
Attempt to set READ ONLY attribute
Invalid request
Unknown batch request
Too many submit retries
No permission
Access from host not allowed
Job already exists
System error occurred
Internal Server error occurred
196 Appendix A
PBS Error Codes
Error Name
Error Code
Parent job of dependent in route queue
Unknown signal name
Bad attribute value
Cannot modify attrib in run state
Request invalid for job state
Unknown queue name
Invalid Credential in request
Expired Credential in request
Queue not enabled
No access permission for queue
Bad user - no password entry
Max hop count exceeded
Queue already exists
Incompatible queue attribute type
Queue Busy (not empty)
Queue name too long
Feature/function not supported
Cannot enable queue, needs add def
Protocol (ASN.1) error
Bad attribute list structure
No free connections
No Server to connect to
Unknown resource
Job exceeds Queue resource limits
No Default Queue Defined
PBS Pro 5.2 197
Administrator Guide
Error Name
Error Code
Job Not Rerunnable
Route rejected by all destinations
Time in Route Queue Expired
Request to MOM failed
(qsub) Cannot access script file
Stage In of files failed
Resources temporarily unavailable
Bad Group specified
Max number of jobs in queue
Checkpoint Busy, may be retries
Limit exceeds allowable
Bad Account attribute value
Job already in exit state
Job files not copied
Unknown job id after clean init
No Master in Sync Set
Invalid dependency
Duplicate entry in List
Bad DIS based Request Protocol
Cannot execute there
Sister rejected
Sister could not communicate
Request rejected -server shutting down
Not all tasks could checkpoint
198 Appendix A
PBS Error Codes
Error Name
Error Code
Named node is not in the list
Node-attribute not recognized
Server has no node list
Node name is too big
Node name already exists
Bad node-attribute value
State values are mutually exclusive
Error(s) during global mod of nodes
Could not contact MOM
No time-shared nodes
Resource monitor specific error codes
Resource unknown
Parameter could not be used
A parameter needed did not exist
Something specified didn't exist
A system error occurred
Only part of reservation made
PBS Pro 5.2 199
Administrator Guide
account 10
accounting log 158, 160
administration 139
administrator 10
aerospace 2
AIX 45
alternate or test version 57
API 10
comment 172
defined 10
reference 87
comment 83
license 83
max_group_run 82
max_running 82
max_user_run 82
np 82
ntype 82
pcpus 83
properties 82
queue 83
reservations 83
resources_assigned 82
resources_available 82
state 82
acl_group_enable 73
acl_groups 73
acl_host_enable 73
acl_hosts 74
acl_user_enable 74
acl_users 74
alt_router 76
checkpoint_min 76
enabled 74
from_route_only 74
hasnodes 76
kill_delay 76
max_group_run 76
max_queuable 74
max_running 74
max_user_res 74
max_user_run 76
priority 75
queue_type 75
resources_assigned 77
resources_available 76
resources_default 75
resources_max 75
resources_min 75
200 Index
route_destinations 76
route_held_jobs 77
route_lifetime 77
route_retry_time 77
route_waiting_jobs 77
started 75
state_count 77
total_jobs 77
acl_host_enable 67
acl_hosts 67
acl_roots 67
acl_user_enable 67
acl_users 67
comment 67
default_node 67
default_queue 68
flatuid 68
licenses 71
log_events 68
mail_uid 68
managers 68
max_group_run 68
max_running 68
max_user_res 69
max_user_run 69
node_pack 69
operators 69
PBS_version 71
query_other_jobs 69
resources_assigned 71
resources_available 70
resources_cost 70
resources_default 70
resources_max 70
scheduler_iteration 70
scheduling 71
server_name 71
server_state 71
state_count 71
system_cost 71
total_jobs 72
autoconf 30
batch or batch processing 10
building PBS 31
during shutdown 148
multi-node jobs 148
prior to SGI IRIX upgrade 149
cluster 9
commands 6
complex 10
MOM 93
Scheduler 111
Server 92
xpbs 168
xpbsmon 170
configure 30
cpusets 24, 48, 103, 105, 122
Cray 49
T3E 50
credential 151
overview 181
site_map_user 151
cycle-stealing 107
Dedicated Time 127
default configuration 66
Defining Holidays 130
destination 10
identifier 11
Dynamic Consumable Resources 126
ncpus 101
epilogue 155, 156
error codes 195
PBS Pro 5.2 201
Administrator Guide
event log 159
examples 133
exclusive VP 9
External Reference Specification xi
Failed Nodes 168
fairshare 127
file staging 11
flat user namespace 151
flatuid 151
floating software licenses 107
Globus 16, 30, 48
Toolkit 30
Globus MOM 109
GNU 30
Grid Forum 4
group 11
authorization 152
ID (GID) 11
high-throughput 138
hold 11
holidays 130
HP-UX 45
IBM 45
SP 46
idle workstations 107
Information Power Grid 4
overview 19
source code 29
Unix/Linux 21
Windows 2000 24
Internal Security 150
Irix 48
comment 172
using comments 172
Job Executor (MOM) 7
job or batch job 11
Job Scheduler 7
Job Server 7
floating 26
keys 25
manager 25
multiple keys 27
pbs_setlicense 27
Linux clusters 2
load balance 9, 123
logfiles 158, 159
maintenance 139
manager 11
Manager privilege 153
message passing 138
meta-computing 4
configuration 93
dynamic resources 126
alloc_nodes_greedy 94
checkpoint_upgrade 94
clienthost 94
cpuset_create_flags 95
cpuset_destroy_delay 95
cpuset_small_mem 96
cpuset_small_ncpus 96
cputmult 95
enforce 96
ideal_load 96
kdb_idle 97
logevent 97
max_load 97
max_shared_nodes 98
prologalarm 100
202 Index
restricted 98
usecp 98
wallmult 100
starting 140
MOM configuration 93
MOM Globus 109
starting 140
monitoring 5
MPI 154
name 128
NASA ix, 2
Ames Research Center 3
Information Power Grid 4
Metacenter 4
addresses 61
ports 61
services 61
Network Queueing System (NQS) 3
New Features in PBS Pro 5.2 13
New Scheduler Features 113
node 8
attribute 9
cluster 8
property 9
timeshared 8
Nodes 78
and virtual processors 8
Nodes File 79
NQS 3, 5
operator 11
privilege 153
owner 11
package installer 21
parallel jobs 138
parent_group 128
pbs_iff 151, 175
pbs_mom 7, 18, 93
pbs_mom_globus 146
pbs_sched 7, 17
pbs_server 7, 17
pbsnodes 171
pbspoe 47
poe 47
Portable Batch System 10
defined 11
make 30
standard 3
predictability 138
preemption 113
Preemptive scheduling 124
preemptive scheduling 124
privilege 153
manager 153
Problem Report 178
prologue 155, 156, 157
qalter 172
qdel 168
qdisable 149
qenable 149
qmgr 52, 54, 62, 175
qmove 54
qrerun 168
qrun 52
qstart 149
qstat 175
qstop 149
qterm 56, 146
queue 9
attributes 72
queuing 5
Redhat Linux 44
rerunable 12
PBS Pro 5.2 203
Administrator Guide
cput 87
defining new 87
listing 87
mem 87
ncpus 87
nodes 87
walltime 87
Resources 87
Root Owned Jobs 154
configuration 111
dynamic resources 126
assign_ssinodes 115
backfill 115
backfill_prime 116
by_queue 116
cpus_per_ssinode 116
dedicated_prefix 116
fair_share 116
fairshare_entity 116
fairshare_usage_res 116
half_life 116
help_starving_jobs 117
load_balancing 117
load_balancing_rr 117
log_filter 117
max_starve 117
mem_per_ssinode 117
nonprimetime_prefix 117
preempt_checkpoint 118
preempt_fairshare 118
preempt_order 118
preempt_prio 118
preempt_queue_prio 119
preempt_requeue 119
preempt_starving 119
preempt_suspend 119
preemptive_sched 118
prime_spill 119
primetime_prefix 117
resources 120
round_robin 120
smp_cluster_dist 120
sort_by 120
strict_fifo 121
sync_time 122
unknown_shares 122
starting 140
scheduling 5
scheduling policies 111
Scyld Beowulf 16
security 139, 150
selective routing 90
attributes 66
recording configuration 92
starting 140
setlicense 26
shares 128
site-customized schedulers 106
software upgrade 53
Solaris 44
source code 29
build procedure 32
distribution 29
Space-sharing Cluster 138
stage in 12
stage out 12
Standard Scheduler 111
Globus MOM 146
MOM 141
Scheduler 145
Server 142
Starting PBS 140
Stopping PBS 146
Support team 178
204 Index
task 12
Tcl 30
tcl/tk 30
temporarily-shared VP 9
Tips & Advice 178
tracejob 166
Tru64 44
Tunable Parameters 115
Unicos 49
Unicos MLS 49
unique_id 128
migration 53
overlay 53
user 12
ID (UID) 12
privilege 153
Veridian 4
virtual processor (VP) 12
Windows 2000 24
workload management 2, 5
xpbs 30, 168
configuration 168
xpbsmon 30, 106, 168, 170
Download PDF
Similar pages