IGAR-2062-3G/4G series
IEEE 802.11 a/b/g/n Access Point Router
User ’s Manual
Version 1.3
Nov, 2014
www.oring-networking.com
COPYRIGHT NOTICE
Copyright © 2012 ORing Industrial Networking Corp.
All rights reserved.
No part of this publication may be reproduced in any form without the prior written consent of
ORing Industrial Networking Corp.
TRADEMARKS
is a registered trademark of ORing Industrial Networking Corp.
All other trademarks belong to their respective owners.
REGULATORY COMPLIANCE STATEMENT
Product(s) associated with this publication complies/comply with all applicable regulations.
Please refer to the Technical Specifications section for more details.
WARRANTY
ORing warrants that all ORing products are free from defects in material and workmanship for a
specified warranty period from the invoice date (5 years for most products). ORing will repair or
replace products found by ORing to be defective within this warranty period, with shipment
expenses apportioned by ORing and the distributor. This warranty does not cover product
modifications or repairs done by persons other than ORing-approved personnel, and this
warranty does not apply to ORing products that are misused, abused, improperly installed, or
damaged by accidents.
Please refer to the Technical Specifications section for the actual warranty period(s) of the
product(s) associated with this publication.
DISCLAIMER
Information in this publication is intended to be accurate. ORing shall not be responsible for its
use or infringements on third-parties as a result of its use. There may occasionally be
unintentional errors on this publication. ORing reserves the right to revise the contents of this
publication without notice.
CONTACT INFORMATION
ORing Industrial Networking Corp.
3F., No.542-2, JhongJheng Rd., Sindian District, New Taipei City 23148, Taiwan (R.O.C.)
Tel: +886-2-2218-1066 // Fax: +886-2-2218-1014
Website: www.oring-networking.com
Technical Support
E-mail: support@oring-networking.com
Sales Contact
E-mail: sales@oring-networking.com (Headquarters)
sales@oring-networking.com.cn (China)
Tables of Content
Getting to Know your Wireless AP Router .................................................. 1
1.1
Overview .......................................................................................................................... 1
1.2
Software Features ........................................................................................................... 1
1.3
Hardware Features .......................................................................................................... 1
Hardware Installation .................................................................................... 3
2.1
Installation Router on DIN-Rail ....................................................................................... 3
2.2
Wall Mounting Installation ............................................................................................... 4
Hardware Overview ....................................................................................... 6
3.1
Front Panel....................................................................................................................... 6
3.2
Front Panel LEDs ............................................................................................................ 8
Cables and Antenna ...................................................................................... 9
4.1
Ethernet Cables ............................................................................................................... 9
4.2
Wireless Antenna ............................................................................................................. 9
4.3
Cellular Antenna ............................................................................................................ 10
5.1
First-time Installation ..................................................................................................... 11
5.2
Configure the Wireless Router ..................................................................................... 14
5.3
Main Interface ................................................................................................................ 14
5.3.1
Basic Setting................................................................................................................ 15
WAN .................................................................................................................................... 15
LAN ..................................................................................................................................... 21
DHCP ................................................................................................................................... 22
Wireless................................................................................................................................ 24
DDNS .................................................................................................................................. 30
Date&Time ........................................................................................................................... 30
5.3.2
Networking Setting ...................................................................................................... 32
Wireless setting..................................................................................................................... 32
Extra parameters for Client Mode(X-Roaming) ..................................................................... 33
NAT Setting.......................................................................................................................... 35
Firewall Setting .................................................................................................................... 37
VPN Setting ......................................................................................................................... 39
VRRP ................................................................................................................................... 46
Routing Protocol (Routing Setting) ....................................................................................... 46
Load Balance Rule ................................................................................................................ 49
5.3.3
System Tools ............................................................................................................... 50
Login Setting ........................................................................................................................ 50
Router Restart ....................................................................................................................... 51
Firmware Upgrade ................................................................................................................ 51
Save/Restore Configurations ................................................................................................. 52
Miscellaneous (Ping) ............................................................................................................ 53
Even warning setting............................................................................................................. 54
DIDO ................................................................................................................................... 59
5.3.4
System Status .............................................................................................................. 59
System Info .......................................................................................................................... 59
System Log........................................................................................................................... 60
Traffic Statistics .................................................................................................................... 60
Wireless Link List ................................................................................................................. 60
Technical Specifications ............................................................................. 61
Compliance .................................................................................................. 63
IGAR-2062 Series User’s Manual
Getting to Know your Wireless AP
Router
1.1
Overview
The ORing IGAR-2062+-3G/4G wireless AP router is designed to
operate in industrial environment. The AP router provides a fast and
effective ways of communicating to the internet over wired or wireless
LAN.
In addition, multiple types of WAN connection are provided for
easily access to the internet.
The ORing IGAR-2062+-3G/4G wireless AP router is IEEE802.11
b/g/n, a/b/g/n wireless equipment.
It is easy for you to extend the
reach and number of computers connected to your wireless network.
With Dual 3G/4G WAN connection, the ORing IGAR-2062+-3G/4G
wireless AP router can be mounted in harsh environment easily to provide internet access
anytime and anywhere.
The ORing IGAR-2062+-3G/4G wireless AP router's VPN capability creates encrypted
"Virtual Tunnels" through the internet, allowing remote or traveling users for secured
connection with the network in your office.
1.2
Software Features
 Intuitive Web-based management user interface for simply and easily operation.
 Functions of firewall provides many security features such as blocking attacks from
hacker, especially IP Spoofing, Ping flood, Ping of Death, DOS, DRDOS, Stealth Scan,
ICMP flooding etc.
 Advanced firewall configuration to extend the capability and security, such as Virtual
Server, Port Trigger, DMZ host, UPnP auto Forwarding, IP Filter and MAC filter.
1.3
Hardware Features

Two 10/100/1000 Base-T(X) Ethernet ports for WAN / LAN connection individually.

Fully Compliant with IEEE802.3af (Power Device at ETH2, WAN port)

Redundant Power Inputs: 12~48 VDC on terminal block

Casing: IP-30

Dimensions(W x D x H) : 74.3(W) x 109.2(D) x 153.6(H) mm
ORing Industrial Networking Corp.
1
IGAR-2062 Series User’s Manual

Operating Temperature: -10 to 60oC

Storage Temperature: -40 to 85 C

Operating Humidity: 5% to 95%, non-condensing
o
ORing Industrial Networking Corp.
2
IGAR-2062 Series User’s Manual
Hardware Installation
2.1
Installation Router on DIN-Rail
Each Wireless AP router has a DIN-Rail kit on rear panel.
The DIN-Rail kit helps AP
router to fix on the DIN-Rail.
Step 1: Slant the router and mount the metal spring to DIN-Rail.
Step 2: Push the router toward the DIN-Rail until you heard a “click” sound.
ORing Industrial Networking Corp.
3
IGAR-2062 Series User’s Manual
2.2
Wall Mounting Installation
Each AP router has another installation method to fix the AP router. A wall mount
panel can be found in the package. The following steps show how to mount the AP router
on the wall:
Step 1: Remove DIN-Rail kit.
Step 2: Use 6 screws that can be found in the package to combine the wall mount panel.
Just like the picture shows below:
ORing Industrial Networking Corp.
4
IGAR-2062 Series User’s Manual
The screws specification shows in the following two pictures.
In order to prevent the
AP routers from any damage, the screws should not larger than the size that used in
IGAR-2062+ series.
Pozidrive
Step 3: Mount the combined AR on the wall.
ORing Industrial Networking Corp.
5
IGAR-2062 Series User’s Manual
Hardware Overview
3.1
Front Panel
The following table describes the labels that stick on the IGAR-2062+-3G/4G.
Port
Description
10/100/1000
10/100/1000Base-T(X) RJ-45 fast Ethernet ports support
Base-T(X) fast
auto-negotiation.
Default Setting :
Ethernet ports
Speed: auto
Duplex: auto
PoE PD Port
ETH2 (WAN port) of IGAR-2062+-3G/4G compliant with
IEEE802.3af PoE specifications and can be connected to PoE
switches.*
ANT.
Reversed SMA connector for external antenna.
(normal SMA connector for LTE antenna)
*Note: Please refer to the products of ORing IPS series for P.O.E. Ethernet switch.
ORing Industrial Networking Corp.
6
IGAR-2062 Series User’s Manual
IGAR-2062+
ORing Industrial Networking Corp.
7
IGAR-2062 Series User’s Manual
1. 2.4/5GHz antenna with typical 2 dBi antenna for 5GHz and 2.4GHz.
2. LED for PWR1 and system status. When the PWR1 links, the green LED will be light
on.
3. LED for PWR2 and system status. When the PWR2 links, the green LED will be light
on.
4. LED for Ethernet port1 status.
5. LED for Ethernet port2 status.
6. LED for WLAN link status.
7. LED for Fault Relay. When the fault occurs, the red LED will be light on.
8. Power Input port
9. Ethernet port1 connector
10. Ethernet port2 connector
11. Digital input
12. Digital output
13. Reset button
14. LED for P.O.E Status
15. LED for Wan status
16. Modem antenna
17. SIM card slot
3.2
Front Panel LEDs
LED
Color
Status
Description
PWR1
Green
Green On
DC power 1 activated.
PWR2
Green
Green On
DC power 2 activated.
Green/Amber
On
Port link up at 10Mbps /1000Mbps.
On
Port link up at 100Mbps.
Blinking
Data transmitted.
On
Port link up at 10Mbps/1000Mbps.
On
Port link up at 100Mbps.
Blinking
Data transmitted.
On
WLAN activated.
Blinking
WLAN Data transmitted.
Modem Ready
ETH1
Green
Green/Amber
ETH2
Green
WLAN
Green
WAN
Green
On
Fault
Red
On
ORing Industrial Networking Corp.
Fault relay.
Power failure or Port
down/fail.
8
IGAR-2062 Series User’s Manual
Cables and Antenna
4.1
Ethernet Cables
The IGAR-2062+-3G/4G WLAN AP has two 10/100/1000 Base-T(X) Ethernet ports.
According to the link type, the AP use CAT 3, 4, 5, 5e, 6 UTP cables to connect to any
other network device (PCs, servers, switches, routers, or hubs).
Please refer to the
following table for cable specifications.
Cable Types and Specifications
Cable
Type
Length
Connector
10Base-T
Cat.
3, 4, 5 100-ohm
UTP 100 m (328 ft)
RJ45
100Base-T(X)
Cat.
5 100-ohm UTP
UTP 100 m (328 ft)
RJ45
5e,6
UTP 100 m (328 ft)
RJ45
1000Base-T(X) Cat
4.2
Max.
Wireless Antenna
2.4GHz/5GHz antenna is used for IGAR-2062+-3G/4G and connected with a reversed
SMA connector. External RF cable and antenna also can be applied with this connector.
ORing Industrial Networking Corp.
9
IGAR-2062 Series User’s Manual
4.3
Cellular Antenna
850/900/1800/2100MHz antenna is used for built-in modem.
External RF cable and
antenna also can be applied with this connector.
Cellular Antenna
4G LTE Antenna
ORing Industrial Networking Corp.
10
IGAR-2062 Series User’s Manual
Management Interface
5.1
First-time Installation
Before installing IGAR-2062+-3G/4G WLAN AP router, you need to access the WLAN
AP router by a computer equipped with an Ethernet card or wireless LAN interface.
Using
an Ethernet card to connect to LAN port is easier and recommended.
Basic connection for IGAR-2062+-3G/4G
Step 1: Select the Power Source
IGAR-2062+-3G/4G AP router can be powered by +12~48V DC power input, or by
P.O.E. (Power over Ethernet) PSE Ethernet switch.
Step 2: Connect a computer to IGAR-2062+-3G/4G
Use either a straight-through Ethernet cable or cross-over cable to connect to ETH1 of
IGAR-2062+-3G/4G AP router to a computer. If the LED of the LAN port lights up, it
indicates the connection is established.
After that, the computer will initiate a DHCP
request to get an IP address from the AP router.
Step 3: Use the web-based manager to configure IGAR-2062+-3G/4G
The default gateway IP of IGAR-2062+-3G/4G AP router is 192.168.10.1.
Start the
web browser of your computer and type http://192.168.10.1 in the address box to access
the webpage.
A login window will popup, and then enter the default login name admin
and password admin.
ORing Industrial Networking Corp.
11
IGAR-2062 Series User’s Manual
Login screen
Step 4: Select WAN connection type
Click the Basic Setting in the top menu to enter the WAN configuration page, select the
proper connection type according to the information of your ISP.
If you use modem/3G as
WAN connection
WAN connection type
ORing Industrial Networking Corp.
12
IGAR-2062 Series User’s Manual
Step 5: Protect the wireless access in encryption mode
Click the Wireless in Basic Setting menu, default encryption mode is None, choose
WEP/WPA to enhance the security of wireless connection.
Wireless security option
Step 6: Review the router settings and check router status
Click the System Status in the top of the menu, the system info page will be shown.
You can check all the configuration and status of the router.
System status Screen
ORing Industrial Networking Corp.
13
IGAR-2062 Series User’s Manual
5.2
Configure the Wireless Router
In this section, the web management page will be explained in detail.
By default setting, you can type http://192.168.10.1 in the address box of web browser
to login the web management interface.
A login window will be prompted, enter username
admin & password admin to login.
Login screen
For security reasons, we strongly recommend you to change the password.
Click on
System Tools > Login Setting and change the password.
5.3
Main Interface
The Home screen will be shown when login successfully.
Main Interface
In the page, you can check the Firmware version, the router running time and the WAN
IP setting.
The following table describes the labels in this screen.
ORing Industrial Networking Corp.
14
IGAR-2062 Series User’s Manual
Label
Description
Firmware
Show the current firmware version.
Uptime
Show the elapsed time since the AP router is started.
Wan IP
Show the WAN IP address.
5.3.1
Basic Setting
WAN
The IGAR-2062+-3G/4G AP router provide four types of WAN connection.
1. WAN Connection Type: Dynamic/Static IP
Dynamic/Static IP
The following table describes the labels in this screen.
Label
Description
Obtain an IP address
Select this option if you would like to have an IP address assigned
automatically
automatically from the WAN port by DHCP server in your network.
Use the following IP
Select this option if you would like to assign an IP address to the
address
WAN port manually. You should set the IP Address, Subnet Mask
and Default gateway appropriately so that they comply with IP
rules.
ORing Industrial Networking Corp.
15
IGAR-2062 Series User’s Manual
Obtain DNS server
Obtain DNS server from DHCP server. If the above Obtain an
address
IP address automatically is selected, this option will be chosen
automatically
accordingly.
Use the following
Specify DNS server address manually.
DNS server
addresses
Use Modem/3G as
Enable this option if you want to use Modem/3G as a backup
backup connection
connection when normal connection is lost.
Phone Number, User Name and Password: Use these settings
to dial up the Modem/3G connection.
Ping Test Site: Use this site address to check if the connection is
alive or lost. Take www.google.com as an example.
2. WAN Connection Type: PPPoE
ORing Industrial Networking Corp.
16
IGAR-2062 Series User’s Manual
PPPoE Screen.
The following table describes the labels in this screen.
Label
Description
User Name /
Enter the username & password provided by your Internet
Password
Service Provider (ISP).
Service Name
Enter the service name provided by your ISP.
AC Name
Specify the IP & DNS
Enter the name of the access concentrator as provided by your
ISP.
Enter static IP and DNS address which may required by some ISP
provided by ISP
Auto: Connect automatically when the router boots up.
Connect on Demand: Select to disconnect the PPP session if
Connection Mode
the router has had no traffic for the specified amount of time.
Enter the Max Idle Time in minutes.
Manual: Select this option to use only the Connect/Disconnect
buttons to call up or close the connection.
Enable this option if you want to use Modem/3G as a backup
connection when PPPoE connection is lost.
Use Modem/3G as
Phone Number, User Name and Password: Use these settings
backup connection
to dial up the Modem/3G connection.
Ping Test Site: Use this site address to check if the connection is
alive or lost. Example is as www.google.com
ORing Industrial Networking Corp.
17
IGAR-2062 Series User’s Manual
3. WAN Connection Type: Modem / 3G/4G
Modem/3G/4G Screen
The following table describes the labels in this screen.
Label
Description
APN
Enter the APN value it is optional and 3 APN can be filled for
service roaming.
User Name
User name provided by your ISP.
Password
Password provided by your ISP.
PIN
Enter the PIN code if PIN check is required.
Auto Connect
If this option is enabled, the connection will be called up when
router boots up.
UIM Status
Show the status of SIM card.
Operations
Click “Connect” to call up the Modem/3G. Click "Disconnect" to
shut down the connection.
Link Status
Show the status of connection, up, down or connecting.
ORing Industrial Networking Corp.
18
IGAR-2062 Series User’s Manual
3G/4G backup function:
3G/4G Backup function screen
The following table describes the labels in this screen.
Label
Description
Mode
Select second Modem backup or both modem load balance,
advance load balance rule setting at Network setting Load
balance rule
WAN Priority
Specifies the ratio of packets for WAN 1 and WAN 2 (only when
Load Balance mode is supported) when several streams are sent
by user. The packets will be randomly assigned to WAN 1 and
WAN 2. If user wants to determine streams to go through certain
WAN interface, user can change setting on function tree:
Network Setting --> Load Balance Rule --> Rule Setting.
APN
Enter the APN value it is optional and 3 APN can be filled for
service roaming.
User Name
User name provided by your ISP.
Password
Password provided by your ISP.
Ping Test Site
Fill the check site
PIN
Enter the PIN code if PIN check is required.
UIM Status
Show the status of SIM card.
ORing Industrial Networking Corp.
19
IGAR-2062 Series User’s Manual
Link Status
Show the status of connection, up, down or connecting.
4. WAN Connection Type: Wireless client
Wireless Client on WAN
Label
Description
Obtain an IP
Select this option if you would like to have an IP address assigned
ORing Industrial Networking Corp.
20
IGAR-2062 Series User’s Manual
address
automatically from the WAN port by DHCP server in your network.
automatically
Use the following IP
Select this option if you would like to assign an IP address to the
address
WAN port manually. You should set the IP Address, Subnet Mask
and Default gateway appropriately so that they comply with IP
rules.
Obtain DNS server
Obtain DNS server from DHCP server.
If the above Obtain an IP
address
address automatically is selected, this option will be chosen
automatically
accordingly.
Use the following
Specify DNS server address manually.
DNS server
addresses
Peer AP SSID
Enter the other AP or AR SSID which you want to client
Site Scan
You can scan the SSIDs which used for AP mode in the certainty
Security Type
area
Set the same security with the Client unit which you want to
connect.
Use Modem/3G as
Enable this option if you want to use Modem/3G as a backup
backup connection
connection when normal connection is lost.
Phone Number, User Name and Password: Use these settings
to dial up the Modem/3G connection.
Ping Test Site: Use this site address to check if the connection is
alive or lost. Take www.google.com as an example.
LAN
These are the IP settings of the LAN interface for the IGAR-2062+-3G/4G
WLAN AP router. The LAN IP address is privately for your internal network and
can not be exposed on the Internet.
LAN Screen
ORing Industrial Networking Corp.
21
IGAR-2062 Series User’s Manual
The following table describes the labels in this screen.
Label
Description
IP Address
The IP address of the LAN interface, the default IP address is
192.168.10.1
Subnet Mask
The Subnet Mask of the LAN interface, the default Subnet mask
is 255.255.255.0
DHCP
DHCP stands for Dynamic Host Control Protocol. The IGAR-2062+-3G/4G AP
router with a built-in DHCP server.
The internal DHCP server will assign an IP
address to the computers (DHCP client) on the LAN automatically.
Set your computers to be DHCP clients by setting their TCP/IP settings to Obtain
an IP Address Automatically. The DHCP server will allocate an unused IP address
from the IP address pool to the requesting computer automatically.
The IP Allocation provides one-to-one mapping of MAC address to IP address.
When a computer with the MAC address requesting an IP from the IGAR-2062+-3G/4G
AP router, it will be assigned with the IP address according to the mapping.
You can
choose one from the client lists and add it to the mapping relationship.
1. DHCP Sever
ORing Industrial Networking Corp.
22
IGAR-2062 Series User’s Manual
DHCP Server Screen
The following table describes the labels in this screen.
Label
Description
DHCP Mode
Select built-in DHCP server or DHCP Forwarder
DHCP Server
Enable or Disable the DHCP Server.
The default setting is
Enable
Starting IP
The starting IP address of the IP range for the DHCP server
Ending IP
The ending IP address of the IP range for the DHCP server
Lease Time
The period of time for the IP to be leased.
Enter the Lease time.
The default setting is 48 hours.
Local Domain Name
Enter the local domain name of private network.
DNS Server 1&2
Enter the DNS Server. It is optional.
WINS Server
Enter the WINS Server. It is optional.
DHCP Relay start IP
Enter DHCP Relay starting IP
ORing Industrial Networking Corp.
It is optional.
23
IGAR-2062 Series User’s Manual
DHCP Relay end IP
Enter DHCP Relay Ending IP
Subnet Mask
Enter DHCP Relay IP Subnet mask
List of DHCP Range
for relay
List DHCP Relay IP range
Choose a Client to
The list shows the MAC addresses and IP addresses that are
Edit
already assigned by IGAR-2062+-3G/4G. Choose one from the
list and click Copy to button for editing.
MAC Address
The MAC addresses of the computer.
IP Address
The IP address to be related to the MAC address.
Static
DHCP
Client
List
The list shows the MAC address and IP address one-to-one
relationship.
Wireless
Wireless Screen
The following table describes the labels in this screen.
Label
Description
Service Set Identifier (SSID) is a unique name that identifies a
network.
SSID
All devices on the network must set the same SSID
name in order to communicate on the network.
If you change
the SSID from the default setting, input your new SSID name in
this field.
Channel 6 is the default channel. All devices on the network
Channel
must share the same channel.*
*Note: The wireless devices will automatically scan and match the
wireless setting of the AP router with the same SSID.
Security options
Select the type of security for WLAN connection:
ORing Industrial Networking Corp.
24
IGAR-2062 Series User’s Manual
None: NO encryption.
WEP: Wired Equivalent Privacy (WEP) is a wireless security
protocol for WLAN.
WEP provides data encryption for
communicating over the WLAN.
WPA/WPA2 Personal: WPA-Personal or WPA2-Personal with
a pre-shared key, each authorized computer is given the
same pass phrase.
WPA/WPA2 Enterprise: Wi-Fi Protected Access (WPA)
authentication in conjunction with a RADIUS server.
802.1x: Authentication through RADIUS server
Security Type – None
No security protection for WLAN.
Security Type – WEP
ORing Industrial Networking Corp.
25
IGAR-2062 Series User’s Manual
Wireless Security Type-WEP Screen
1.
Choose one of three Auth Modes: Open, Share and WEPAUTO
2.
WEP Encryption: Select 64 Bit or 128 Bit WEP encryption.
3.
Key Type: Select ASCII or Hex key type.
4.
Default Key Index: Select one of the keys to be the active key.
5.
Key 1-4: Input up to four encryption keys.
ASCII (American Standard Code for Information Interchange) is a code for
representing English letters as numbers from 0-127. Hex digits consist of the numbers
0-9 and the letters A-F.
Security Type – WPA/WPA2-Personal
ORing Industrial Networking Corp.
26
IGAR-2062 Series User’s Manual
Wireless Security Type WPA/WPA2 Personal Screen
1.
Security Type: Select WPA/WPA2 Personal.
2.
Choose one of three Auth Modes: WPAPSK, WPA2PSK, WPAPSK/WPA2PSK
mix
3.
Encryption Type: Select TKIP or AES or TKIP/AES mix.
4.
Share Key: Enter your pass phase. The pass phase should be between 8 and 64
characters.
Security Type – WPA /WPA2 Enterprise
Wireless Security Type-WPA/WPA2 Enterprise Screen
ORing Industrial Networking Corp.
27
IGAR-2062 Series User’s Manual
1.
Security Type: Select WPA/WPA2 Enterprise
2.
Auth Mode: Choose one of three Auth Modes: WPA, WPA2, WPA/WPA2 mix.
3.
Encryption Type: Choose one of three Encryption Types: TKIP, AES, TKIP/AES
mix.
4.
Radius Server IP: Enter the IP address of the RADIUS Server.
5.
Port: Enter the RADIUS port (1812 is default).
6.
Shared Secret: Enter the RADIUS password or key.
Security Type –802.1x
1. Security Type: Select 802.1X
2. WEP Encryption: Select 64 Bit or 128 Bit WEP encryption.
3. Key Type: Select ASCII or Hex key type.
4. Default Key Index: Select one of the keys to be the active key.
5. Key 1-4: Input up to four encryption keys.
6. Radius Server IP: Enter the IP address of the RADIUS Server.
7. Port: Enter the RADIUS port (1812 is default).
8. Shared Secret: Enter the RADIUS password or key.
ORing Industrial Networking Corp.
28
IGAR-2062 Series User’s Manual
RADIUS, or Remote Authentication Dial-In User Service, is a widely deployed
protocol that enables companies to authenticate, authorize and account for remote
users who want access to a system or service from a central network server.
Radius server validates your proof, also carry on the authorization. So the Radius
server received by ISA server responded (point out the customer carries proof to be not
granted) and it means that the Radius server did not authorize you to carry.
Even if
the proof has already passed an identify verification, the ISA server may also refuse
you to carry a claim according to the authorization strategy of the Radius server.
The principle of the Radius server is shown in the following pictures:
ORing Industrial Networking Corp.
29
IGAR-2062 Series User’s Manual
DDNS
Dynamic Domain Name System is a method of keeping a domain name linked to a
changing IP address.
DDNS Screen
For example, Choose DDNS Service: www.dyndns.org and configure the following
instructions:
The following table describes the labels in this screen.
Label
Description
User Name
Enter the user name for your DDNS account.
Password
Enter the password for your DDNS account.
Domain
Enter the domain names provided by your dynamic DNS service
provider.
Date&Time
In this page, you can set the date & time of the device. The correct date & time will
be helpful for logging of system events. A NTP (Network Time Protocol) client can be
used to synchronize date & time with NTP server through internet.
Date & Time Screen
ORing Industrial Networking Corp.
30
IGAR-2062 Series User’s Manual
The following table describes the labels in this screen.
Label
Description
Local Date
Set local date manually.
Local Time
Set local time manually.
Time Zone
Select the time zone manually
Get Current Date &
Click this button; you can set the time from your browser.
Time from Browser
NTP
Enable or disable NTP function to synchronize time from the NTP
server.
NTP Server 1
The primary NTP Server.
NTP Server 2
The secondary NTP Server.
Synchronize
This is the scheduled time when the NTP synchronization
performed.
ORing Industrial Networking Corp.
31
IGAR-2062 Series User’s Manual
5.3.2
Networking Setting
Wireless setting
1. Advanced
Wireless options interface
The following table describes the labels in this screen.
Label
Description
Radio Button
Enable or Disable Wireless function
Beacon Interval
The default value is 100.
The Beacon Interval value indicates
the frequency interval of the beacon.
A beacon is a packet
broadcast by the AP to synchronize the wireless network.
50 is
recommended in poor reception.
DTIM Interval
The default value is 1.
This value, between 1 and 255
milliseconds, indicates the interval of the Delivery Traffic
Indication Message (DTIM). A DTIM field is a countdown field
informing clients of the next window for listening to broadcast and
multicast messages. When the AP has buffered broadcast or
multicast messages for associated clients, it sends the next DTIM
with a DTIM Interval value. Its clients hear the beacons and
awaken to receive the broadcast and multicast messages.
Fragmentation
This value should remain at its default setting of 2346.
Threshold
range is 256-2346 bytes. It specifies the maximum size for a
packet before data is fragmented into multiple packets.
ORing Industrial Networking Corp.
The
If you
32
IGAR-2062 Series User’s Manual
experience a high packet error rate, you may slightly increase the
Fragmentation Threshold.
Setting the Fragmentation Threshold
too low may result in poor network performance. Only minor
modifications of this value are recommended.
RTS Threshold
This value should remain at its default setting of 2347.
range is 0-2347 bytes.
The
Should you encounter inconsistent data
flow, only minor modifications are recommended.
If a network
packet is smaller than the preset RTS threshold size, the
RTS/CTS mechanism will not be enabled.
The AP sends
Request to Send (RTS) frames to a particular receiving station
and negotiates the sending of a data frame.
After receiving an
RTS, the wireless station responds with a Clear to Send (CTS)
frame to acknowledge the right to begin transmission.
Wireless
Network
Mode
Preamble
You can select 802.11 b/g/n wireless mode mix or single
Values are Long and Short, default value is Long.
If your
wireless device supports the short preamble and you are having
trouble getting it to communicate with other 802.11b devices,
make sure that it is set to use the long preamble
Extra parameters for Client Mode(X-Roaming)
X-Roaming setting interface
The following table describes the labels in this screen
Label
Description
Roaming
Disable: Disable X-Roaming protocol.
X-roaming: Enable X-Roaming protocol
Scan channel
All: scan all support channel
Manual: only scan “channel select” value
Channel Select
Assign the roaming channel value
ORing Industrial Networking Corp.
33
IGAR-2062 Series User’s Manual
Sensitivity
Set the signal sensitivity
Scan interval
Set the scan interval
Wireless advance setting Screen
2. MAC Filter
Use MAC Filter to allow or deny wireless clients to associate with IGAR-2062+-3G/4G
AP router.
You can manually add a MAC address or select the MAC address from
Associated Clients that are currently associated with IGAR-2062+-3G/4G.
MAC Filter Screen
The following table describes the labels in this screen.
Label
Description
MAC Filter
Enable or disable the function of MAC filter.
MAC Filter List
This list shows the MAC addresses that are in the selected filter.
Connected Clients
This list shows the wireless MAC addresses that associated with
AP.
MAC Address
MAC addresses for editing.
Apply
Click Apply to activate the configurations.
ORing Industrial Networking Corp.
34
IGAR-2062 Series User’s Manual
NAT Setting
1. Virtual Server
Virtual Server is used for setting up public services on the LAN, such as DNS, FTP and
Email. Virtual Server is defined as a Local Port to the LAN servers, and all requests
from Internet to this Local port will be redirected to the computer specified by the Local IP.
Any PC that was used for a virtual server must have static or reserved IP Address
because its IP address may change when requesting IP by DHCP.
Virtual Server
The following table describes the labels in this screen.
Label
Description
Virtual Server
Enable or disable Virtual Server.
Description
Enter the description of the entry. Acceptable characters consist
of '0-9', 'a-z', 'A-Z'.
Public IP
This field accepts null value.
Enter the public IP that is allowed to access the virtual service, if
not specified, choose All.
Public Port
The port number on the WAN (Wide Area Network) side that will
be used to access the virtual service.
Protocol
The protocol used for the virtual service.
Local IP
The IP of the computer that will be providing the virtual service.
Local Port
The port number of the service used by the Private IP computer.
Enable Now
Enable the virtual server entry after adding it.
Virtual server list
Click Edit to edit the virtual service entry, Del to delete the entry.
ORing Industrial Networking Corp.
35
IGAR-2062 Series User’s Manual
2. DMZ
It allows a computer to be exposed to the Internet.
This feature is useful for gaming
purposes.
Enter the IP address of the internal computer that will be the DMZ host.
Adding a
client to the DMZ may expose your local network with variety of security risks, so only
use this option carefully.
DMZ Screen
The following table describes the labels in this screen.
Label
Description
DMZ
Enable or disable the DMZ.
Description
Description for the DMZ host entry.
DMZ Host IP
Enter the IP address of the computer to be in the DMZ.
3. UPnP
The UPnP (Universal Plug and Play) feature allows the devices, such as Internet
computers, to access the local host resources or devices as needed. UPnP devices can
be automatically discovered by the UPnP service application on the LAN.
UPnP Screen
ORing Industrial Networking Corp.
36
IGAR-2062 Series User’s Manual
The following table describes the labels in this screen.
Label
Description
UPnP
Enable or disable UPnP.
Enable NAT-PMP
NAT-PMP allows a computer in a private network (behind a NAT
router) to automatically configure the router to allow parties
outside the private network to contact with each other. NAT-PMP
operates with UDP. It essentially automates the process of port
forwarding.
UPnP List
Check the box to enable NAT-PMP.
This table lists the current auto port forwarding information.
Application: The application that generates this port forwarding.
Ext Port: The port opened on WAN side.
Protocol: The protocol type.
Int Port: The port redirected to the local computer.
IP Address: The IP address of local computer to be redirected to.
Status: This status shows if the entry is valid or not.
Firewall Setting
1. IP Filter
Filters are used to deny or allow LAN computers from accessing the internet. It also
allow or deny WAN hosts to access LAN computers.
IP Filter Screen
ORing Industrial Networking Corp.
37
IGAR-2062 Series User’s Manual
The following table describes the labels in this screen.
Label
Description
IP Filter
Enable or disable the IP Filter.
Description
Enter description for the entry.
Rule
Select DROP, ACCEPT and REJECT rule for the entry.
Direction
Specify the direction of the data flow that is to be filtered.
IP Address
Enter the IP address of the source and destination computer.
Protocol
Choose which protocol to be filtered.
Enable Now
Enable the entry after adding it.
IP filter list
Click edit for editing the entry, click Del to delete the entry.
2. MAC Filter
Filters are used to deny or allow LAN computers from accessing the internet, according to
their MAC address.
MAC Filter Screen
The following table describes the labels in this screen.
Label
Description
MAC Filter
Enable or disable the MAC Filter.
Description
Enter the description for the entry.
Rule
Select DROP, ACCEPT and REJECT rule for the entry.
MAC Address
Enter the MAC address to be filtered.
Enable Now
Enable the entry after adding it.
IP filter list
Click Edit for editing the entry, click Del to delete the entry.
ORing Industrial Networking Corp.
38
IGAR-2062 Series User’s Manual
VPN Setting
VPN Setting is settings that are used to create virtual private tunnels to remote VPN
gateways.
The tunnel technology supports data confidentiality, data origin,
authentication and data integrity of network information by utilizing encapsulation
protocols, encryption algorithms, and hashing algorithms.
1. Open VPN
Open VPN is a full-functioned SSL VPN solution which can accommodates a wide
range of configurations including remote access, site-to-site VPNs, WiFi security, and
enterprise-scale remote access solutions with load balancing, failover, and fine-grained
access-controls.
Open VPN Screen
ORing Industrial Networking Corp.
39
IGAR-2062 Series User’s Manual
The following topology shows the common use of VPN connection from WAN side.
1: Open VPN Server
Connection to Open VPN Server
Before connecting to the Openvpn server of IGAR-2062+-3G/4G AP routuer, please
install openvpn client software for your windows PC.
It can be download from
http://openvpn.net/download.html#stablel. The current version of Openvpn used in
IGAR-2062+-3G/4G is version 2.0.9. The corresponding software for client should be
installed.
The following table describes the labels in this screen.
Label
Description
Open VPN Server
Enable or disable the function of Open VPN Server.
Tunnel Protocol
Select UDP or TCP protocol.
Port
Input the number about the port, and the default is 1194.
LZO Compression
Enable or disable the function of LZO Compression.
Keys Setting
Select Auto to use the preset certificates, select Manual to paste
your certificates. Please install openvpn client software to
generate your certificates and paste them here. For more
information, please visit openvpn website.
ORing Industrial Networking Corp.
40
IGAR-2062 Series User’s Manual
2: Open VPN Client
Two routers are needed for creating site-to-site VPN connection using this mode.
The following table describes the labels in this screen.
Label
Description
Open VPN Client
Enable or disable the function of Open VPN Client.
You can
allow or deny the Open VPN Client with this option.
Server IP
Enter the Open VPN Server IP address.
Tunnel Protocol
Select UDP or TCP protocol.
Port
Enter the port number, default is 1194.
LZO Compression
Enable or disable the LZO Compression.
Keys Setting
Select Auto to use the preset certificates, select Manual to paste
your certificates.
Please install software for openvpn client to
generate your certificates and paste them here.
For more
information, please visit openvpn website.
3: Open VPN Server VS Client
ORing Industrial Networking Corp.
41
IGAR-2062 Series User’s Manual
The chart above displays the connection of Open VPN Server and Client. The Server
IP and Client IP address should configure with the same network domain.
2. PPTP VPN
The PPTP (Point to Point Tunneling Protocol) VPN feature allows PC connected to the
router from WAN port, just like connecting in the LAN.
To create a PPTP connection to the router, you should create a PPTP network
connection if you are using a window PC.
The steps are: Right click Network >
property > create a new connection > connect to my work space (VPN) > use VPN
to internet > enter the user name and password which are set in the page.
PPTP VPN Screen
ORing Industrial Networking Corp.
42
IGAR-2062 Series User’s Manual
The following topology shows the common use of PPTP connection from the internet.
Connection to PPTP VPN Server
The following table describes the labels in this screen.
Label
Description
PPTP Server
Enable or disable PPTP VPN Server.
Server IP
Enter the server side IP address, default is the LAN port IP.
Client IP
Enter the IP address range, format is as 192.168.10.xx-xx,
connected client will be assigned the IP address.
CHAP-Secrets
Enter the username and password pairs, format is as user * pass
*, multiple username password pairs are allowed.
ORing Industrial Networking Corp.
43
IGAR-2062 Series User’s Manual
3. PPTP Client
If the router A want to link with the others which is not in the same network with the router
A, the function of PPTP client should support in the router page.
PPTP VPN Line
ORing Industrial Networking Corp.
44
IGAR-2062 Series User’s Manual
Label
PPTP Client
Server
IP/Hostname
Username/Pass
word
Option
Description
Enable or disable PPTP Client.
Enter the server IP address or hostname.
Enter the username and password which is signed by PPTP server.
Reconnect on failure: Pitch on this option, it will be reconnect when
the link is on failure.
Require
MPPE:
Choose
Enable
Require
MPPE
(Microsoft
Point-to-Point Encryption) to encrypt data across Point-to-Point Protocol
(PPP) and Virtual Private Network links.
Operations
Click “Connect” to link the server, if or not, you can click “”Disconnect” to
break off from the server.
Link Status
Show the status about the link.
ORing Industrial Networking Corp.
45
IGAR-2062 Series User’s Manual
VRRP
Routing Protocol (Routing Setting)
This page shows the information of routing table. The initial state of the router connect to the
WAN, it will be based on the outside networks to access the routing table automatically. You
can refer the shows about the bellow page.
The table shows the normal routing table
ORing Industrial Networking Corp.
46
IGAR-2062 Series User’s Manual
1.
Use Dynamic Routing
Use the dynamic routing, you should not choose “Disable” about the RIPv1 & v2 in the
routers.
Click “Apply”, and you can see the more information in the Current Routing Table, which
shows the network segment of the other router.
Label
Description
Current Routing
Table
Static
Router
Entry
Mode
Show the current the routing information.
Not RIP and enter the right value in the textbox will be showing.
If you want to the PC in the router can visit the outside network, only
choose the Gateway Mode; if or not, you choose the Router Mode.
RIPv1 &v2
Telnet Setting
Choose “Disable” in the Static routing.
Only use in the Dynamic routing.
Simultaneously, only use the Telnet function in the dynamic routing. You can telnet the LAN
IP and there are many orders.
ORing Industrial Networking Corp.
47
IGAR-2062 Series User’s Manual
2.
Use Static Routing
Use the Static routing, you should choose “Disable” about the RIPv1 & v2 in the routers.
Click “Apply”, and you can see the more information in the Current Routing Table and Static
Route Entry, which shows the network segment of the other router.
Use the dynamic routing; it will have many ways such as RIP, OSPF.BGP. In this router, we
use the RIP Protocol to finish the dynamic routing table.
ORing Industrial Networking Corp.
48
IGAR-2062 Series User’s Manual
PC1
PC2
The Routing Topography
RIP, Routing Information Protocol, is a dynamic routing protocol used in local and wide
area networks. As such it is classified as an interior gateway protocol (IGP) using the
distance-vector routing algorithm.
After all settings, PC1 can visit PC2 which is different network segment of the PC1.
Load Balance Rule
Restrict specific Source IP stream via specific interface, this feature all affect at WAN  load
balance modem backup mode
ORing Industrial Networking Corp.
49
IGAR-2062 Series User’s Manual
5.3.3
System Tools
Login Setting
At this page, the administrator can change the login name and password.
The
default name and password is admin and admin.
Login Setting Screen
The following table describes the labels in this screen.
Label
Description
Old Name
This field shows the old login name.
Old Password
Before making a new setting, you should provide the old
password for verification.
Acceptable characters of this field
contains '0-9', 'a-z', 'A-Z' and must be between 0 to 15
characters in length. An empty password is also acceptable.
New Name
Enter a new login name.
Acceptable characters of this field
contains '0-9', 'a-z', 'A-Z' and must be between 1 to 15
characters in length. An empty name is not acceptable.
New Password
Enter a new login password.
Acceptable characters of this
field contains '0-9', 'a-z', 'A-Z' and must be between 0 to 15
characters in length.
Confirm New Password
Retype the password to confirm it. Acceptable inputs of this
field contains '0-9', 'a-z', 'A-Z' and must be between 0 to 15
characters in length.
Web Protocol
Choose the web management page protocol.
HTTP and
HTTPS are both supported.
ORing Industrial Networking Corp.
50
IGAR-2062 Series User’s Manual
Port
Choose the web management page port number. For HTTP,
default port is 80; For HTTPS, default port is 443.
HTTPS (HTTP over SSL) is a Web protocol which encrypts and decrypts user page
requests as well as the pages that are returned by the Web server.
Router Restart
If you want restart the router through the Warm Reset, click Restart Now to restart
the Wireless Router. Also, you can set a Scheduling time to make the router restart.
Router Restart Screen
Firmware Upgrade
Firmware Upgrade Screen
Newer firmware may provide better performance or function extensions.
To
upgrade the new firmware, you need a firmware file which matches the model of this
AP router. It will take several minutes to upload and update the firmware.
After the
upgrade is done successfully, reboot the router to utilized new firmware.
Important Notice:
DO NOT POWER OFF THE ROUTER OR PRESS THE RESET
BUTTON WHILE THE FIRMWARE IS BEING UPGRADED.
ORing Industrial Networking Corp.
51
IGAR-2062 Series User’s Manual
Save/Restore Configurations
Save/Restore Configurations Screen
Save:
The configuration file can be downloaded. (Internet Explorer user will need to
click on the protection bar on top and click choose “download files”)
The following table describes the labels in this screen.
Label
Description
Download
The current system settings can be saved as a file into your PC.
configuration
Upload configuration
The configuration can be restored to the router.
To reload a
system settings file, click on Browse to browse your local hard
drive and locate the system settings file previously saved.
Click
Upload when you have selected the file.
Restore Default
You may also reset the router to the factory settings by clicking on
Settings
Restore Default Settings.
The router will reboot to validate the
default settings.
ORing Industrial Networking Corp.
52
IGAR-2062 Series User’s Manual
Miscellaneous (Ping)
Miscellaneous Screen
The Ping Test is used to send Ping packets to test if a computer whether it is on the
Internet or test if the WAN connection is OK. Enter a domain or IP in the destination
box and click Ping to test.
ORing Industrial Networking Corp.
53
IGAR-2062 Series User’s Manual
Even warning setting
1. System Log
System Log setting interface
The following table describes the labels in this screen.
Label
Description
Syslog Server IP
Not only the syslog keeps the logs locally, it can also log to remote
server.
Specify the IP of remote server.
Leave it blank to
disable logging remotely.
Syslog Server Port
Specify the port of remote logging. Default port is 514.
ORing Industrial Networking Corp.
54
IGAR-2062 Series User’s Manual
2. E-Mail
E-Mail setting interface
The following table describes the labels in this screen.
Label
Description
SMTP Server
Simple Message Transfer Protocol, enter the backup host to use
if primary host is unavailable while sending mail by SMTP server.
Server Port
Specify the port where MTA can be contacted via SMTP server.
E-mail Address 1-4
Inputs specify the destination mail address.
ORing Industrial Networking Corp.
55
IGAR-2062 Series User’s Manual
3.SNMP
SNMP setting interface
ORing Industrial Networking Corp.
56
IGAR-2062 Series User’s Manual
The following table describes the labels in this screen.
Label
Description
SNMP Agent
SNMP (Simple Network Management Protocol) Agent is a service
program that runs on the access point.
The agent provides
management information to the NMS by keeping track of various
operational aspects of the AP system.
Turn on to open this
service and off to shutdown it.
SNMP
Trap
Server
Specify the IP of trap server, which is the address to which it will
1-4
send traps AP generates.
Community
Community is essentially password to establish trust between
managers and agents. Normally "public" is used for read-write
community.
SysLocation
Specify sysLocation string.
SysContact
Specify sysContact string.
4.Relay
Relay setting interface
ORing Industrial Networking Corp.
57
IGAR-2062 Series User’s Manual
5. SMS
SMS setting interface
ORing Industrial Networking Corp.
58
IGAR-2062 Series User’s Manual
DIDO
5.3.4
System Status
System Info
System Info Screen
This page displays the details information for the AP router including model name,
model description, firmware version, WAN, LAN and wireless settings.
ORing Industrial Networking Corp.
59
IGAR-2062 Series User’s Manual
System Log
System Log Screen
The router keeps a running log of events and activities occurring on the router,
several filters are provided for displaying related log entries.
Click the button 'Refresh' to refresh the page.
Click the button 'Clear Logs' to clear the log entries.
Traffic Statistics
Traffic Statistics Screen
This page displays the network traffic statistics for both received and transmitted
packets through the Ethernet port and wireless connections.
Wireless Link List
This page of the list displays the Mac Address of the wireless clients connected.
ORing Industrial Networking Corp.
60
IGAR-2062 Series User’s Manual
Technical Specifications
LAN Interface
Ethernet Ports
2 x 10/100/1000Base-T(X), Auto MDI/MDI-X
Protocols
IP, TCP, UDP, DHCP, BOOTP, ARP/RARP, DNS,
SNMP MIB II, HTTPS, SNMPV1/V2, Trap, Private
MIB
Cellular Interface
Cellular Standard
GSM / GPRS/ EGPRS/ EDGE / WCDMA / HSDPA /
HSUPA
Dual-band : HSUPA 1900/2100 MHz
3G Band Option
Quad-band : GSM/GPRS/EDGE 850/900/1800/1900
MHz
WCDMA/HSDPA 850/900/1900/2100 MHz
America(US)
LTE:
700/1700/2100/ MHz
UMTS/HSDPA/HSUPA/HSPA+/DC-HSPA+:
800/850/1900/2100 MHz
GSM/GPRS/EDGE:
4G LTE Band Option
850/900/1800/1900 MHz
Europe(EU)
LTE:
800/900/1800/2100/2600 MHz
UMTS/HSDPA/HSUPA/HSPA+/DC-HSPA+:
900/2100 MHz
GSM/GPRS/EDGE:
900/1800/1900 MHz
WLAN Interface
Operating Mode
AP/ Client /Bridge/ AP-Client
Antenna and Connector
2 antennas with 2dBi for 5GHz and 2.4GHz in
reverse SMA connector
Radio Frequency Type
DSSS, OFDM
Modulation
IEEE802.11b: CCK/DQPSK/DBPSK
IEEE802.11a/g: OFDM
IEEE802.11n: BPSK, QPSK, 16-QAM, 64-QAM
Frequency Band
ORing Industrial Networking Corp.
America / FCC :
2.412~2.462 GHz (11 channels)
61
IGAR-2062 Series User’s Manual
5.180~5.240 GHz & 5.745~5.825 GHz ( 9 channels )
Europe CE / ETSI : 2.412~2.472 GHz (13 channels)
5.180~5.240 GHz (4 channels)
Transmission Rate
IEEE 802.11b: 11, 5.5, 2, 1 Mbps;
IEEE 802.11a/g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps
IEEE 802.11n:
20 MHz BW: 130, 117, 104, 78, 52, 39, 26, 13
40 MHz BW: 270, 243, 216, 162, 108, 81, 54, 27
Transmit Power
802.11a: 12dBm ± 1.5dBm@54Mbps
802.11b: 17dBm ± 1.5dBm@11Mbps
802.11g: 16dBm ± 1.5dBm@54Mbps
802.11gn HT20: 15dBm ± 1.5dBm @MCS7
802.11gn HT40: 14dBm ± 1.5dBm @MCS7
802.11an HT20: 12dBm ± 1.5dBm @MCS7
802.11an HT40: 11dBm ± 1.5dBm @MCS7
Receiver Sensitivity
802.11a : -76dBm ± 2dBm@54Mbps
802.11b : -85dBm ± 2dBm@11Mbps
802.11g : -76dBm ± 2dBm@54Mbps
802.11gn HT20:-75dBm ± 2dBm@MCS7
802.11gn HT40:-72dBm ± 2dBm@MCS7
802.11an HT20:-74dBm ± 2dBm@MCS7
802.11an HT40:-71dBm ± 2dBm@MCS7
Encryption Security
WEP: (64-bit, 128-bit key supported)
WPA/WPA2:802.11i (WEP and AES encryption)
WPA-PSK (256-bit key pre-shared key supported)
TKIP encryption
Wireless Security
LED Indicators
SSID broadcast disable
3 x LEDs, PWR1(2)(PoE) / Ready:
1) Red On: Power is on and booting up.
2) Green On: Power is on and functioning
normally.
2 x LEDs, ETH1(2)
Speed: Green for port Link at 1000Mbps
Amber for port Link at 100Mbps.
Off for port Link at 10Mbps
WLAN Link/ACT:
Green for WLAN
ORing Industrial Networking Corp.
62
IGAR-2062 Series User’s Manual
Fault indicator:
Red On: Ethernet link down or power down
Power Requirements
Power Input Voltage
Dual DC inputs. 12~48VDC on 6-pin terminal block
Reverse Polarity Protection
Present
Power Consumption
8.3 Watts
Environmental
Operating Temperature
-25 to 70oC
Storage Temperature
-40 to 85oC
Operating Humidity
5% to 95%, non-condensing
Mechanical
Dimensions(W x D x H)
74.3(W) x 109.2(D) x 153.6(H) mm
Casing
IP-30 protection
Regulatory Approvals
EMI
FCC Part 15, CISPR (EN55022) class A
EN61000-4-2
EMS
EN61000-4-4
(ESD),
(EFT),
EN61000-4-3
EN61000-4-5
(RS),
(Surge),
EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11
Shock
IEC60068-2-27
Free Fall
IEC60068-2-32
Vibration
IEC60068-2-6
Rail Traffic
EN60950-1
Compliance
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference and (2) this device must accept any
interference received, including interference that may cause undesired operation.
RF exposure warning: The equipment complies with RF exposure limits set forth for an
uncontrolled environment. The antenna(s) used for this transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
You are cautioned that changes or modifications not expressly approved by the party
responsible for compliance could void your authority to operate the equipment. This device
ORing Industrial Networking Corp.
63
IGAR-2062 Series User’s Manual
should be operated with minimum distance 20cm between the device and all persons.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
Industry Canada Statement
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil
ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
Industry Canada - Class B This digital apparatus does not exceed the Class B limits for radio
noise emissions from digital apparatus as set out in the interference-causing equipment
standard entitled “Digital Apparatus,” ICES-003 of Industry Canada.
Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux
appareils numériques de Classe B prescrites dans la norme sur le matérial brouilleur:
“Appareils Numériques,” NMB-003 édictée par l’Industrie.
Operation is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
L'opération est soumise aux deux conditions suivantes: (1) cet appareil ne peut causer
d'interférences,et (2) cet appareil doit accepter toute interférence, y compris celles
susceptibles de provoquer fonctionnement du dispositif.
To reduce potential radio interference to other users, the antenna type and its gain should be
so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that
permitted for successful communication.
Afin de réduire les interférences radio potentielles pour les autres utilisateurs, le type
ORing Industrial Networking Corp.
64
IGAR-2062 Series User’s Manual
d'antenne et son gain doivent être choisie que la puissance isotrope rayonnée équivalente
(PIRE) est pas plus que celle premise pour une communication réussie
RF exposure warning: The equipment complies with RF exposure limits set forth for an
uncontrolled environment. The antenna(s) used for this transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
Avertissement d'exposition RF: L'équipement est conforme aux limites d'exposition aux RF
établies pour un incontrôlés environnement. L'antenne (s) utilisée pour ce transmetteur ne
doit pas être co-localisés ou fonctionner en conjonction avec toute autre antenne ou
transmetteur.
ORing Industrial Networking Corp.
65
Download PDF
Similar pages