Disclaimer - FixYourDLP.com

Disclaimer
This user manual is provided as a free service by FixYourDLP.com. FixYourDLP is in no way responsible
for the content of this manual, nor do we guarantee its accuracy. FixYourDLP does not make any claim
of copyright and all copyrights remain the property of their respective owners.
About FixYourDLP.com
FixYourDLP.com (http://www.fixyourdlp.com) is the World’s #1 resource for media product news,
reviews, do-it-yourself guides, and manuals.
Informational Blog: http://www.fixyourdlp.com
Video Guides: http://www.fixyourdlp.com/guides
User Forums: http://www.fixyourdlp.com/forum
FixYourDLP’s Fight Against Counterfeit Lamps:
http://www.fixyourdlp.com/counterfeits
Sponsors:
RecycleYourLamp.org – Free lamp recycling services for used lamps:
http://www.recycleyourlamp.org
Lamp Research - The trusted 3rd party lamp research company:
http://www.lampresearch.com
Discount-Merchant.com – The worlds largest lamp distributor:
http://www.discount-merchant.com
Sponsored by DM
IN5302, IN5304 User’s Guide
5300
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Regulatory models: F5300
010-0652-00
Declaration of Conformity
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Manufacturer: InFocus Corporation, 27500 SW Parkway Ave. Wilsonville,
Oregon 97070 USA
We declare under our sole responsibility that this projector conforms to the
following directives and norms:
EMC Directive 2004/108/EC
EuP Directive 2005/32/EC
EMC: EN 55022
EN 55024
EN 61000-3-2
EN 61000-3-3
Low Voltage Directive 2006/95/EC
Safety: IEC 60950-1:2005, MOD
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by InFocus Corporation
may void authority to operate the equipment.
Trademarks
DisplayLink is a trademark of DisplayLink Corporation.
Apple, Macintosh, and PowerBook are trademarks or registered trademarks
of Apple Computer, Inc. IBM is a trademark or registered trademark of
International Business Machines, Inc. Microsoft, PowerPoint, and Windows
are trademarks or registered trademarks of Microsoft Corporation. Adobe
and Acrobat are trademarks or registered trademarks of Adobe Systems
Incorporated. DLP® and the DLP logo are registered trademarks of Texas
Instruments and BrilliantColor™ is a trademark of Texas Instruments.
InFocus, In Focus, and INFOCUS (stylized) are either registered trademarks
or trademarks of InFocus Corporation in the United States and other
countries.
Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
Agency Approvals
UL, cUL
Other specific Country Approvals may apply. Please see product
certification label.
This document applies to regulatory model M5300.
FCC Warning
Input ratings: AC 100-240V, 4.8-1.7A,50-60Hz
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
InFocus reserves the right to alter product offerings and specifications at
interference, and (2) this device must accept any interference received,
any
without
notice.
T
H
E
T
R
U
S
T
E
D
S
O
U
R
C
E
F
O
R
P
R
O
J
E
C
T
ORtime
L
AMP
SANDA
CCE
S
S
ORI
E
S
including interference that may cause undesired operation.
1
Table of Contents
Introduction
Positioning the projector
Ceiling Mount
Cable management
Connecting power
Connecting a computer source
Optional computer connections
Displaying an image
Adjusting the image
Connecting a video device
Video device connections
Shutting down the projector
Troubleshooting your setup
Using the remote control
Using the audio
Using the keypad buttons
Optimizing computer images
Presentation features
Optimizing video images
Customizing the projector
Dynamic Messaging
Using the menus
Basic Picture menu
Advanced Picture menu
Setup menu
Status and Service menu
Help
Using Network Functions
Using LitePort
Maintenance
Cleaning the lens
Replacing the projection lamp
Using the security lock
Appendix
SplitScreen Compatibility
RS232 Commands
Index
5
7
8
9
10
10
11
12
13
14
14
16
16
24
25
26
26
26
27
27
27
28
29
30
31
34
34
35
40
43
43
44
45
46
47
T
HET
RUS
T
E
DS
OU
RCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
47
54
2
Important Operating Considerations for Safety
•
Refer to this guide for proper startup and shutdown procedures.
•
Follow all warnings and cautions in this manual and on the projector.
•
Place the projector in a horizontal position no greater than 8 degrees off
axis.
•
Locate the projector at least 4' (1.2m) away from any heating or cooling
vents.
•
Do not block ventilation openings. Locate the projector in a wellventilated area without obstructions to intake or exhaust vents. Do not
place the projector on a tablecloth or other soft covering that may block
the vents.
•
Do not place the projector in direct sunlight, humid, greasy or dusty
places or in places where the projector may come into contact with
smoke or steam.
•
Do not look directly into the lens while the projector is being used.
•
Do not drop the projector.
•
Do not spill liquid on the projector. Spilled liquid may damage the
projector.
•
Use the power cord provided. Connect the power cord to a receptacle
with a protective safety (earth) ground terminal. A surge-protected
power strip is recommended.
•
Do not overload wall outlets.
•
When disconnecting the power cord, hold the plug, not the cord.
•
When the projector is ceiling mounted, wear protective eyewear to
prevent eye injury before opening lamp door.
•
The projector must be installed by a qualified professional in order to
ensure proper operation and reduce the risk of hazards or injury. It is
not recommended you install the projector yourself.
•
Refer all service to qualified service personnel. Servicing your own
projector can be dangerous to you and will void the warranty.
•
Only use replacement parts specified by InFocus. Unauthorized
substitutions may result in fire, electrical shock, or injury, and may
void the warranty
•
Only genuine InFocus lamps are tested for use in this projector. Use of
non InFocus lamps may cause electrical shock and fire, and may void
the projector warranty.
•
Hg – Lamp contains mercury. Manage in accordance with local
disposal laws. See www.lamprecycle.org.
•
The projector uses a high-pressure mercury glass lamp. The lamp may
fail prematurely, or it may rupture with a popping sound if jolted,
scratched, or handled while hot. The risk of lamp failure or rupture
also increases as the lamp age increases; please replace the lamp when
you see the “Replace Lamp” message.
•
In the unlikely event of a lamp rupture, particles may exit through the
projector vents. Keep people, food, and drinks out of the "keep out"
area under and around the projector, as indicated by the "X" areas
below.
•
Wash hands after handling the cables supplied with this product.
•
The projector remote control uses batteries. Make sure the batteries’
polarity (+/-) is aligned correctly. Dispose of used batteries in
accordance with local disposal laws.
•
Use an InFocus approved ceiling mount kit for proper fitting,
m
ventilation and installation. The warranty does not cover any damage
8P
’ /S
1.5R
2.4A
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AM
NDACCE
S
S
I
E
S
/O
m
5’
caused by use of non-approved ceiling mount kits or by installing in an
improper location.
3’ / 1
3
m
2’ /
0.6
m
Follow these instructions to help ensure image quality and lamp life over
the life of the projector. Failure to follow these instructions may affect the
warranty. For complete details of the warranty, see the Warranty Booklet
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
4
Introduction
Optional Accessories
Optional accessories include optional top covers in a variety of finishes, the
Commander-2 remote, ceiling mount, DisplayLink Extender, DisplayLink
Wireless Adapter, and LiteShow II. These items and other accessories can be
found on our website at www.infocus.com or at your local dealer.
Your new digital projector is simple to connect, easy to use, and
straightforward to maintain. It is a versatile projector that is flexible enough
for business presentations and home video viewing, too. The IN5302 has
native XGA 1024x768 resolution, and the IN5304 has WXGA 1280x800
resolution. This guide applies to both products. They are compatible with a
wide variety of computers and video devices.
Top rear cover
LiteTouch keypad
Top front cover
Product specifications
To read the latest specifications on your multimedia projector, be sure to
visit our support website at www.infocus.com/support, as specifications are
subject to change.
Online registration
Register your projector on our website at www.infocus.com/register to
activate your warranty and receive product updates, announcements, and
registration incentives.
Lamp access
panel
Included Items
Lens
Remote control
receiver (IR)
Power cord
connector
Projector
VGA Computer cable
Remote Control
Power Cord
Documentation
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Connector panel
USB cable
5
Connector panel
The projector provides both computer and video connection options,
including:
the Always-On Functions submenu are set to Yes. It is designed to provide
power to an InFocus LiteShow II wireless device or InFocus DisplayLink
Extender device.
•
VGA computer (2)
12V Screen Trigger output
•
HDMI (2)
•
S-video
•
Composite video
The 3.5mm mini-jack screen trigger provides a 12 volt, 0.25 amp DC output.
It turns on when the lamp is lighted. If you connect your projection screen
to this output using the cable that came with your screen, the screen will
move down when the lamp is turned on and the screen will return to its
storage position, when the lamp is turned off.
•
Component video
•
BNC RGBHV and YPbPr for RGBHV, EDTV and HDTV
•
Separate audio inputs for video and computer
•
USB DisplayLink connector, for computer audio/video input. This
USB connection also provides power out for the DisplayLink Wireless
Adapter.
Audio out /
IR repeater
Security lock
LAN/ Liteport
Screen
Trigger/5V
RS-232
Monitor out
DisplayLink
connector
The projector also provides the following connectors:
•
Monitor out, to provide an image on your desktop computer as well as
on the projection screen.
•
LAN port for network control and web server.
•
LitePort, for connecting a USB flash drive containing JPEG images.
•
Audio out, to provide sound for external speakers.
•
5 volt DC output
•
12V screen trigger output
•
Wired remote jack (for use with optional Commander 2 remote)
•
IR repeater jack
•
RS-232 connector for serial control. Command control codes are in the
Appendix and on our support website at www.infocus.com/support.
Composite
video
S-video
audio 4
L
L
audio 3
L
audio 1
audio out
R
R
R
audio 2
IR
screen trigger
12V DC
250 mA
wireless
ready
DisplayLink
TM
serial
video 4
LAN
monitor out
H
computer 1
DisplayLink
video 3
B
G
R
computer 2
computer 3
Y
Pb
Pr
remote
VGA
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
6
LitePort
computer 4
V
Cable cover
The coaxial 6.4mm x 2.2mm jack provides a constant 5 volt, 2 amp DC
output when the projector is on, and will also provide power when the
projector is in standby (powered off) if Network and DisplayLink items in
certified
+5V DC; 2A
video 5
RGBHV
YPbPr
NOTE: Only VGA video is sent to the Monitor out connector.
5 volt DC output
audio 5
Audio in
HDMI Component
video
Wired
remote
Positioning the projector
•
To determine where to position the projector, consider the size and shape of
your screen, the location of your power outlets, and the distance between the
projector and the rest of your equipment. Here are some general guidelines:
•
Maximum Shift
5%
Distance (L)
Distance (L)
Horizontal Image Offset +/-15%
If the image is square but not centered on the screen or viewing area,
adjust it by using the lens shift dials. Use the Horizontal dial to shift the
lens left or right. Use the Vertical dial to shift the lens up or down.
NOTE: As the lens is shifted away from the lens centerline, the horizontal shift range is reduced. To adjust lens shift efficiently we suggest you
follow these steps:
1 Use vertical lens shift to move the image closer to the lens centerline
than the final vertical position.
2 Use horizontal lens shift to determine the center horizontal position,
then move image to the center horizontal position.
3 Use vertical lens shift to move the image away from the lens centerline
to the final vertical position.
4 Use horizontal lens shift to move the image to the final horizontal position.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
5 If lens shift is unable to move the image far enough, move the projector
(preferable) or tilt the projector and then use vertical and horizontal keystone to re-position the image.
20%
Maximum Shift
5%
100% (H)
20%
Screen Height
100% (H)
Position the projector to the desired distance from the screen. The
distance from the lens of the projector to the screen, the zoom setting,
and the video format determine the size of the projected image.
25%
•
Screen
100% (H)
Position the projector within 10’ (3m) of your power source and within
6’ (1.8m) of your video device (unless you purchase extension cables).
To ensure adequate cable access, do not place the projector within 6”
(.15m) of a wall or other object.
Screen
25%
•
(IN5304)
(IN5302)
Position the projector on a flat surface at a right angle to the screen. The
projector must be at least 4.9’ (1.5m) from the projection screen.
Screen Height
100% (H)
•
The vertical image offset range is 105%~130% for the IN5302 and
105%~125% for the IN5304 (default for both is 105%). The default
horizontal image offset is +/-15%, however at maximum vertical image
offset, there is no horizontal lens shift.
7
Ceiling Mount
Table 1: IN5302 (XGA)
Range of distance to the screen for a given screen size
If you wish to install the projector on the ceiling:
•
The projector must be installed by a qualified professional in order to
ensure proper operation and reduce the risk of hazards or injury. It is
not recommended you install the projector yourself.
•
We strongly recommend using InFocus approved ceiling mounts for
proper fitting, ventilation and installation. Refer to the installation
guide that comes with the InFocus Ceiling Mount Kit (p/n SP-CEILINSTALL) for more information. The warranty does not cover any
damage caused by use of non-approved ceiling mount kits or by
installing in an improper location.
•
The ceiling must be strong enough to support the projector and the
installation must be in accordance with any local building codes. Consult your dealer for more information.
Distance to screen
•
Maximum supported physical pitch is +/-8º.
Diagonal Screen
Size (inches/m)
Minimum distance
(feet/m)
Maximum Distance
(feet/m)
•
Maximum supported physical horizontal roll is +/-8º.
•
60/1.524
80/2.032
90/2.286
150/3.810
6.66/2.03
8.92/2.72
10.07/3.07
16.93/5.16
10.20/3.11
13.71/4.18
15.45/4.71
25.85/7.88
Keep all adjacent surfaces 3” (76mm) from sides, front and rear and
.87” (22mm) from the bottom of projector to preserve required airflow
around the projector.
Distance to screen
Diagonal Screen
Size (inches/m)
Minimum distance
(feet/m)
Maximum Distance
(feet/m)
60/1.524
80/2.032
90/2.286
150/3.810
6.43/1.96
8.63/2.63
9.71/2.96
16.34/4.98
10.63/3.24
14.21/4.33
16.01/4.88
26.77/8.16
Table 2: IN5304 (WXGA)
Range of distance to the screen for a given screen size
8º
audio 5
audio 4
L
L
R
R
audio 3
L
audio 1
R
audio 2
audio out
screen trigger
12V DC
250 mA
IR
wireless
ready
TM
DisplayLink
certified
+5V DC; 2A
video 5
serial
video 4
LAN
monitor out
LitePort
computer 4
V
H
computer 1
DisplayLink
video 3
B
G
R
computer 2
computer 3
Y
Pb
Pr
remote
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
8
Cable management
The integrated cable management system allows you to keep the cables
organized. To use the cable management system, thread the cables into the
slots as shown in the illustration.
cable management system
Using the cable management
system provides you with a
clean, professional-looking
installation.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
9
Connecting power
RGBHV connection
Connect one end of the BNC cable to the computer and the other end of the
cable into the BNC connectors on the projector.
Connect the black power cord to the Power connector on the rear of the
projector and to your electrical outlet. The Power light on the Status
Indicator Panel (page 16) turns amber.
NOTE: Always use the power cord that shipped with the projector.
Connect power cord
audio 5
audio 4
L
audio 3
L
L
audio 1
R
audio 2
audio out
screen trigger
12V DC
250 mA
R
R
IR
wireless
ready
DisplayLink
TM
certified
+5V DC; 2A
video 5
serial
video 4
LAN
monitor out
LitePort
computer 1
DisplayLink
computer 4
V
video 3
B
H R
G
computer 2
computer 3
Y
Pb Pr
remote
Connecting a computer source
DisplayLink
If you have a Windows or Macintosh computer, connect the USB cable
between your computer's USB port and the projector's DisplayLink
connector*. Then to begin installation of the DisplayLink software:
Connect USB cable
audio 5
audio 4
L
L
R
R
audio 3
L
audio 1
R
audio 2
audio out
screen trigger
12V DC
250 mA
Windows: Follow the instructions on the screen.
IR
wireless
ready
DisplayLink
serial
video 4
LAN
monitor out
LitePort
computer 4
V
H TM
certified
+5V DC; 2A
video 5
computer 1
DisplayLink
video 3
B
G
R
computer 2
computer 3
Y
Pb Pr
remote
Macintosh: A folder will open containing a file named DisplayLink
Installer.pkg. Open that file and follow the instructions on the screen.
MOLEX
MOLEX
* For detailed DisplayLink instructions and troubleshooting, and to download the
latest DisplayLink software, go to www.infocus.com/support/displaylink.
VGA connection
audio 5
L
Connect computer cable
Connect one end of the provided computer cable to the VGA 1 or VGA 2
connector on the projector and the other to the VGA connector on your
computer. If you are using a desktop computer, you will need to disconnect
the monitor cable from the computer’s video port first (you can connect this
monitor cable to the Monitor Out connector on the projector, see next page).
audio 4
L
audio 3
L
audio 1
R
audio 2
audio out
screen trigger
12V DC
250 mA
R
R
IR
wireless
ready
DisplayLink
TM
certified
+5V DC; 2A
video 5
serial
video 4
LAN
monitor out
LitePort
computer 4
V
H computer 1
DisplayLink
video 3
B
G
R
computer 2
computer 3
Y
Pb Pr
remote
HDMI 1.3 connection
HDMI is a standard, uncompressed, all-digital audio/video interface.
HDMI provides an interface between sources, such as set-top boxes, DVD
players, and receivers and your projector. Plug an HDMI cable into the
video out connector on the video device and into either the HDMI 1 or HDMI
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
2 connector on the projector.
To take advantage of HDMI 1.3 Deep Color (30 bit) you must have a 1.3compatible source.
10
Optional computer connections
Connect monitor cable
To get sound from the projector, connect an audio cable (optional cable, not
included) to your computer and to the Audio 1 (used with VGA 1) or Audio 2
(used with VGA 2) connector on the projector. You can also assign a your
source to a different audio in connector, see page 25 and page 32. You may
also need an adapter.
audio 5
audio 4
L
L
R
R
audio 3
L
audio 1
R
audio 2
audio out
screen trigger
12V DC
250 mA
IR
wireless
ready
DisplayLink
TM
certified
+5V DC; 2A
video 5
serial
video 4
LAN
monitor out
LitePort
computer 4
V
H computer 1
DisplayLink
video 3
B
R
G
computer 2
computer 3
Y
Pb Pr
remote
If you are using a desktop computer and want to see the image on your
computer screen as well as on the projection screen, connect the computer’s
monitor cable to the Monitor Out connector on the projector.
Connect audio cable
audio 5
L
audio 4
L
audio 3
L
audio 1
R
audio 2
audio out
screen trigger
12V DC
250 mA
R
R
IR
wireless
ready
DisplayLink
TM
certified
+5V DC; 2A
NOTE: Only VGA video is sent to the Monitor out connector.
video 5
serial
video 4
LAN
monitor out
LitePort
computer 4
V
H computer 1
DisplayLink
video 3
B
G
R
computer 2
computer 3
Y
Pb Pr
remote
To display a presentation from a USB flash drive, see the Using LitePort section on page 40. This feature converts presentations to JPEG images and
eliminates the need for a computer source. It can also be integrated with
common wall plates and conference room input/output panels.
To advance slides in a PowerPoint presentation using the remote control,
plug the USB cable between the projector’s DisplayLink connector and your
computer. Then press the up and down arrow buttons on the remote control
to move through your slides.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
11
Displaying an image
Press Power button
Touch the Power button on the keypad or the remote.
The Power button blinks green and the fans start to run. When the lamp
turns on, the start up screen will display and the Power button will become
solid green. It can take a minute for the image to achieve full brightness.
hori
zon
tal
zoo
m
focu
s
vert
ical
No start up screen? Get help on page 17.
Turn on computer or
video device
Turn on your computer or video device.
The image should appear on the projection screen. If it doesn’t, press the
Source button on the projector’s keypad or remote.
If you are using a VGA cable to connect your computer to the projector (instead
of DisplayLink):
If using a laptop, make sure its external video port is active.
Many laptops do not automatically turn on their external video port when a
projector is connected. Usually a key combination like Fn + F8 or CRT/LCD
key turns the external display on and off. Locate a function key labeled
CRT/LCD or a function key with a monitor symbol. Press Fn and the
labeled function key simultaneously.
Activate laptop’s external port
Monitor key or
LCD/CRT key
Refer to your laptop’s documentation for more information about your laptop’s key combination or go to the InFocus website at: http://www.infocus.com/Support/LaptopActivation.aspx.
Fn key
No laptop image? Try pressing the Auto Image button on the keypad or
remote.
Is your laptop connected to the projector's DisplayLink connector? See the
InFocus DisplayLink Software User's Guide (available on the InFocus
website at www.infocus.com/displaylink) for troubleshooting information.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
12
Adjusting the image
Adjust distance
Position the projector to the desired distance from the screen at a 90 degree
angle to the screen. See page 8 for a table listing of screen sizes and
distances.
Remove cover
Remove the projector top cover
(b)
a. Slide the tabs on the side toward the rear of the projector to unlock
the projector top cover.
(a)
hor
izo
nta
l
zoo
m
foc
us
ver
tica
l
b. Slide the top toward the front of the projector to unhook it from the
projector body.
(a)
(c)
c. Lift off.
Adjust the zoom or focus.
Adjust zoom, focus and lens
shift
If the image is square but not centered on the screen or viewing area, adjust
it by using the lens shift dials. See page 7 for details.
Rotate the elevator feet for granular adjustment of the projector’s height.
Avoid placing your hands near the hot exhaust vent at the side of the
projector.
focus
zoom
horizontal
Adjust height
Adjust the Contrast or Brightness in the Basic Picture menu. See page 29 for
help with these menu adjustments.
Release button
foot
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDElevator
ACCE
S
S
ORI
E
S
13
vertical
Connecting a video device
HDMI 1.3 connection
HDMI is a standard, uncompressed, all-digital audio/video interface.
HDMI provides an interface between sources, such as set-top boxes, DVD
players, and receivers and your projector. Plug an HDMI cable into the
video out connector on the video device and into either the HDMI 1 or HDMI
2 connector on the projector.
You can connect video devices such as VCRs, DVD players, camcorders,
digital cameras, video game consoles, HDTV receivers, and TV tuners to the
projector. You can connect the audio directly to the projector to get sound
from the built-in speaker, or you can bypass the projector’s audio system
and connect the audio directly from your source to a stereo or home theater
system.
To take advantage of HDMI 1.3 Deep Color (30 bit) you must have a 1.3compatible source.
You can connect the projector to most video devices that can output video.
You cannot directly connect the coaxial cable that enters your house from a
cable or satellite company; the signal must pass through a tuner first.
Examples of tuners are digital cable boxes, VCRs, digital video recorders,
and satellite TV boxes. Basically, any device that can change channels is
considered a tuner.
S-video connection
If your video device uses a round, four-prong S-video connector, plug an Svideo cable into the S-video connector on your video device and into the Svideo connector on the projector. Use the audio cable as described above.
Keep in mind that S-video delivers higher quality video output than
composite.
Although the aspect ratio is automatically selected by the projector based on
the signal input, you can change the aspect ratio, if desired. The projector’s
Aspect Ratio setting is accessed through the Resize button on the remote or
through the projector’s Basic Picture Menu. See page 29 for more
information.
VGA connection
If your video device has a 15-pin VGA output, plug one end of the included
computer cable into the VGA connector on your video source. This
connector may be labeled “To Monitor” on the video source. Plug the
computer cable into the VGA 1or VGA 2 connector on the projector.
Video device connections
Component video connection
Plug the component cable into the video device. Plug the other end of the
component cable into the Component connectors (or if using BNC connectors, plug into the YPbPr connectors).
No video cables are provided with the projector. You can order cables from
InFocus or use your own.
Composite video connection
In addition, a Component to VGA adapter can be used in conjunction with
the VGA connectors. Plug the component cable into the video device. Plug
the other end of the component cable into the adapter and plug the adapter
into the VGA 1 or VGA 2 connector.
Plug the composite video cable’s yellow connector into the video out
connector on the video device. Plug the other yellow connector into the
yellow Composite connector on the projector.
Plug the white connector of a Mini-plug audio Y-cable into the left audio
Component offers the highest quality analog video output.
out connector on the video device and plug the red connector into the right
audio out connector on the video device. Plug the other end of the cable into
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
the associated audio in connector on the projector.
Keep in mind that video output from composite connections is not as high
quality as S-video.
14
What is Aspect Ratio?
4:3 screen
Aspect ratio is the ratio of the image width to image height. Standard TV
screens and older laptops are 4:3; HDTV and most DVDs are 16:9; and
widescreen computers are 16:10. If you are projecting onto a screen, the
size/shape of the screen will influence the aspect ratio you decide to use. If
you are projecting onto a blank wall, there are no screen size restrictions.
What you plan to project will also help you choose between 4:3, 16:9 or
16:10. Many TV shows are 4:3, while most movies are 16:9.
16:9 screen
4:3
mode
If you have a 16:9 screen then you should select an aspect ratio of 16:9 for
widescreen movies or HDTV, and Native for 4:3 content. If you have a 4:3
screen you should still use 16:9 for widescreen movies or HDTV, but you
also have the option of using either 4:3 (to fill the screen) or Native (for
direct pixel mapping) for 4:3 content. Force Wide can also be enabled to
automatically resize less common aspect ratios to 16:10.
16:9
mode
Native
mode
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
15
Shutting down the projector
Troubleshooting your setup
Screen Save Time
The Status Indicator Panel on top of the projector indicates the state of the
projector and is a helpful when troubleshooting.
You can make the black screen appear after a preset number of minutes by
turning on the Screen Save Time feature in the Setup menu. See page 31.
Auto Off Time
The projector has an Auto Off Time feature that automatically turns the
projector off if no active sources are detected and no user interaction with
the projector is performed for 30 minutes. By default, this feature is off. You
can change the length of time, see page 31.
Table 3: Status indicator light behavior and meaning
Turning off the projector
To turn the projector off, press the Power button on the remote or keypad.
The lamp turns off and the LED blinks amber for 10 seconds while the fans
continue to run to cool the lamp. When the lamp has cooled, the LED lights
amber and the fans stop. Unplug the power cable to completely power off
the projector.
Icon
Meaning
Power, solid amber
The projector is plugged in.
Power, blinking green
The power button has been pressed and
the software is initializing.
Power, solid green
The projector is on and initialized.
Power, blinking amber
The power button has been pressed to
turn the projector off and the fans are
running to cool the projector.
Temperature
The projector is too hot. Make sure the
vents aren’t blocked (see page 22). Turn
the projector off and wait one minute,
then turn the projector on again. Contact
Technical Support if the problem persists.
Visit www.infocus.com/support to contact
service.
Lamp
Turn the projector off and wait one
minute, then turn the projector on again.
If the lamp light turns on again, replace the
lamp and reset the lamp timer (page 45).
Wrench/Service
Turn the projector off and wait one
minute, then turn the projector on again.
If the service lamp turns on again, service
is required. Visit www.infocus.com/
support to contact service.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
16
Problem
Solution
Result
No start up screen
Plug power cord into the projector then
Correct image
audio 5
audio 4
audio 3
L
L
L
audio 1
audio out
R
R
R
audio 2
IR
screen trigger
12V DC
250 mA
wireless
ready
DisplayLink
TM
certified
+5V DC; 2A
video 5
serial
video 4
LAN
monitor out
LitePort
computer 4
V
H computer 1
DisplayLink
video 3
B
G
R
computer 2
computer 3
Y
Pb Pr
remote
audio 5
audio 5
audio 4
audio 3
L
L
L
L
audio 1
audio out
audio 4
L
audio 3
L
audio 1
R
audio 2
audio out
screen trigger
screen trigger
R
R
R
IR
audio 2
R
IR
DisplayLink
wireless
ready
DisplayLink
TM
TM
certified
+5V DC; 2A
certified
video 5
serial
video 4
R
ready
+5V DC; 2A
video 5
serial
video 4
LAN
monitor out
LAN
monitor out
LitePort
LitePort
computer 1
DisplayLink
computer 1
DisplayLink
computer 4
computer 4
V
V
video 3
H B
G
R
Startup
Screen
12V DC
250 mA
12V DC
250 mA
wireless
computer 3
computer 2
Y
Pb H video 3
B
G
R
computer 3
computer 2
Y
Pb Pr
remote
Pr
remote
press power button
If your computer is using the projector's DisplayLink
connector, see the DisplayLink Software User's
Guide for troubleshooting information.
Only start up screen appears
Computer image projected
Press the Source button
Activate the laptop’s external port
audio 5
L
audio 4
L
audio 3
L
audio 1
R
audio 2
audio out
screen trigger
audio 5
12V DC
250 mA
R
R
IR
wireless
ready
DisplayLink
TM
certified
+5V DC; 2A
video 5
serial
video 4
LAN
monitor out
LitePort
computer 4
V
H computer 1
DisplayLink
video 3
B
G
R
computer 2
computer 3
Y
Pb Pr
remote
A
L
Startup
Screen
audio 4
L
audio 3
L
audio 1
R
audio 2
audio out
screen trigger
12V DC
250 mA
R
R
IR
wireless
ready
DisplayLink
TM
certified
+5V DC; 2A
video 5
serial
video 4
LAN
monitor out
LitePort
computer 4
V
H computer 1
DisplayLink
video 3
B
G
R
computer 2
computer 3
Y
Pb Pr
remote
A
Restart laptop
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
17
Problem
Solution
Result
No computer image, just the words “Signal out of
range”
Press the Auto Image button on the keypad or remote. To
adjust computer refresh rate, go to Control Panel > Display >
Settings > Advanced > Adapter (location varies by operating
system).
Computer image projected
audio 5
audio 4
L
audio 3
L
L
audio 1
R
audio 2
audio out
screen trigger
12V DC
250 mA
R
audio 5
audio 4
L
L
R
R
R
IR
wireless
ready
DisplayLink
L
audio 1
R
audio 2
audio out
screen trigger
video 5
IR
TM
serial
video 4
LAN
monitor out
ready
computer 4
DisplayLink
TM
certified
+5V DC; 2A
LAN
LitePort
computer 1
DisplayLink
computer 4
video 3
H B
G
R
LitePort
computer 1
DisplayLink
wireless
serial
video 4
monitor out
V
certified
+5V DC; 2A
audio 3
12V DC
250 mA
video 5
computer 2
computer 3
Y
Pb Pr
remote
A
V
Signal out of
the range
video 3
H B
G
R
computer 2
computer 3
Y
Pb Pr
remote
You may also need to set a different resolution on your
computer, as shown in the following problem, “image fuzzy or
cropped”
Only my laptop’s background appears, not the
Desktop icons
audio 5
L
audio 4
L
DisplayLink - Use DisplayLink software to change the display
mode from Extended Desktop to Duplicated Desktop.
Windows - Disable “Extend my Windows Desktop” in Control
Panel > Display > Settings > Display 2 (location varies by
operating system)
Background and Desktop projected
audio 3
L
audio 1
R
audio 2
audio out
screen trigger
12V DC
250 mA
R
R
IR
wireless
audio 5
ready
DisplayLink
L
TM
audio 4
L
audio 3
L
audio 1
R
audio 2
audio out
screen trigger
certified
+5V DC; 2A
video 5
12V DC
250 mA
serial
video 4
LAN
monitor out
R
LitePort
R
computer 1
DisplayLink
IR
wireless
ready
DisplayLink
TM
certified
+5V DC; 2A
computer 4
V
H video 3
B
G
R
computer 2
computer 3
Y
Pb Pr
video 5
remote
serial
video 4
LAN
monitor out
A
LitePort
computer 4
V
H computer 1
DisplayLink
video 3
B
G
R
computer 2
computer 3
Y
Pb Pr
remote
A
Uncheck this
option, then
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
click
Apply
18
Problem
Solution
Result
Image fuzzy or cropped
Set your computer’s display resolution to the native
resolution of the projector (Start > Settings > Control
Panel > Display > Settings tab)
Image clear and not cropped
A
A
A
For a laptop,
disable laptop
monitor or turnon dual-display
mode
Image not centered on screen
Move projector, adjust zoom and lens shift
Correct image
ho
riz
on
tal
zo
om
foc
us
ve
rtic
L
audio 4
L
audio 5
al
audio 5
audio 3
L
audio 1
R
audio 2
audio out
L
audio 4
L
audio 3
L
audio 1
R
audio 2
audio out
screen trigger
screen trigger
12V DC
250 mA
12V DC
250 mA
R
R
IR
R
wireless
IR
DisplayLink
wireless
ready
DisplayLink
TM
TM
video 5
serial
video 4
LAN
LAN
monitor out
certified
+5V DC; 2A
certified
serial
video 4
R
ready
+5V DC; 2A
video 5
monitor out
LitePort
LitePort
H video 3
B
G
R
computer 2
computer 3
computer 1
DisplayLink
computer 1
DisplayLink
computer 4
computer 4
V
Y
V
Pb Pr
H video 3
B
G
R
computer 2
computer 3
Y
Pb Pr
remote
remote
A
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
19
Problem
Solution
Result
Image not square
Adjust Keystone in the Basic Picture menu
Square image
Image not sharp
Adjust Sharpness in the Basic Picture menu
Correct image
Image does not fit 4:3 or 16:9 screen
Change aspect ratio to 4:3 or 16:9 in Basic
Picture>Aspect Ratio menu
Correct image
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
20
Problem
Image upside down
A
Image reversed left to right
Solution
Result
Turn off Ceiling Mount in Setup menu
Correct image
Turn off Rear Project in Setup menu
Correct image
Adjust color, tint, brightness, contrast in the Basic
Picture menu and/or color space in the Advanced
Picture menu
Correct image
A
Projected colors don’t match source
COLOR
COLOR
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
21
Problem
Solution
Result
The video embedded in my PowerPoint presentation
does not play on the screen
If your computer is using the projector's DisplayLink
connector, see the DisplayLink Software User's Guide
for video troubleshooting information.
Turn off the internal LCD display on your laptop
Embedded video plays correctly
audio 5
audio 4
L
audio 5
L
audio 4
L
L
audio 3
L
audio 1
R
audio 2
audio out
screen trigger
12V DC
250 mA
audio 3
L
audio 1
R
audio 2
audio out
screen trigger
R
R
wireless
ready
IR
DisplayLink
TM
12V DC
250 mA
certified
+5V DC; 2A
R
R
IR
wireless
ready
DisplayLink
TM
serial
LAN
monitor out
LAN
LitePort
computer 1
DisplayLink
computer 4
monitor out
H video 4
serial
video 4
LitePort
V
computer 1
DisplayLink
computer 4
V
video 5
certified
+5V DC; 2A
video 5
G
R
computer 3
computer 2
Y
Pb H video 3
B
G
R
computer 3
computer 2
Y
Pb Pr
remote
video 3
B
A
Pr
remote
A
B
B
Lamp won’t turn on, Temperature light is on
Make sure vents aren’t blocked, turn the projector off
and allow it to cool for one minute.
Lamp turns on
Temperature light
audio 5
L
audio 5
L
audio 4
L
R
L
audio 1
R
audio 2
audio out
IR
audio 3
L
audio 1
R
audio 2
audio out
screen trigger
12V DC
250 mA
audio 5
audio 4
L
L
R
R
audio 3
L
audio 1
R
audio 2
audio out
screen trigger
wireless
R
DisplayLink
IR
LitePort
computer 1
DisplayLink
video 5
ready
TM
computer 3
Y
Pb computer 4
G
R
computer 2
computer 3
Y
Pb Pr
remote
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
22
H DisplayLink
TM
certified
LAN
LitePort
computer 1
DisplayLink
video 3
B
G
R
computer 2
computer 3
Y
Pb Pr
remote
video 3
B
ready
monitor out
computer 1
DisplayLink
remote
H serial
computer 4
V
LitePort
Pr
V
video 4
certified
LAN
monitor out
computer 2
video 5
DisplayLink
serial
video 4
video 3
R
wireless
+5V DC; 2A
wireless
+5V DC; 2A
LAN
G
IR
TM
certified
+5V DC; 2A
B
R
12V DC
250 mA
ready
monitor out
H L
screen trigger
serial
video 4
computer 4
V
audio 4
audio 3
12V DC
250 mA
R
video 5
Startup
Screen
Problem
Solution
Result
“Replace lamp” message appears at startup, lamp
won’t turn on, Lamp light is turned on
Lamp must be replaced (see page 44)
Lamp turns on
Lamp light
audio 5
L
audio 4
L
audio 3
L
audio 1
R
audio 2
audio out
screen trigger
12V DC
250 mA
R
audio 5
audio 4
L
L
R
R
R
IR
audio 3
wireless
ready
DisplayLink
TM
certified
+5V DC; 2A
L
audio 1
R
audio 2
audio out
screen trigger
12V DC
250 mA
video 5
serial
video 4
LAN
monitor out
IR
LitePort
computer 1
DisplayLink
wireless
ready
DisplayLink
TM
computer 4
certified
+5V DC; 2A
V
H video 3
B
G
R
computer 2
computer 3
Y
Pb Pr
remote
video 5
serial
video 4
LAN
monitor out
LitePort
computer 4
V
H computer 1
DisplayLink
video 3
B
G
R
computer 2
computer 3
Y
Pb Pr
remote
Replace lamp
Lamp door
Still need assistance?
If you need assistance, visit our support website at www.infocus.com/support
or call us. Check out the How To section for additional information on using
this projector for home theater or gaming applications.
This product is backed by a limited warranty. An extended warranty plan
may be purchased from your dealer. When sending the projector in for
repair, we recommend shipping the unit in its original packing material, or
having a professional packaging company pack the unit. Please insure your
shipment for its full value.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
23
Startup
Screen
Using the remote control
•
•
•
•
The remote uses two (2) provided AA batteries. You can install the batteries
by removing the cover from the remote’s back, aligning the + and - ends of
the batteries, sliding them into place, and then replacing the cover.
Caution:
•
When replacing the batteries, be aware that using batteries other than
the type provided with the projector may risk severe damage to the
remote. When disposing of the batteries, be sure to do so in an environmentally proper manner.
•
If the remote control gets wet, wipe it dry immediately.
•
Avoid excessive heat and humidity.
•
Ensure the batteries’ polarity (+/-) is aligned correctly.
•
Do not mix new and old batteries together, or different types of batteries together.
•
Replace the batteries as soon as they run out.
•
Remove batteries from the remote control when storing or not in use
for a prolonged period.
Presets button to select stored settings (see page 29).
Mute button to silence the audio.
Auto Image button to resynchronize the projector to the source.
Resize button to switch among aspect ratios (see page 29).
Wired Remote Option
If the wireless range of the standard remote is not sufficient, an optional
Commander-2 remote can be wired directly into the projector’s Wired
Remote connector.
Troubleshooting the remote
•
•
To operate, point the remote at the front of the projector (not at the
computer). The range of optimum operation is about 30’ (9m).
Make sure the batteries are installed in the proper orientation and are
not dead.
Make sure you’re pointing the remote at the projector or the screen, not
the computer, and are within the remote range of 30’ (9m). For best
results, point the remote at the projector.
Navigation
buttons
Press the remote’s Power button to turn the projector on and off (see page 16
for shutdown information).
Press the remote’s Menu button to open the projector’s menu system. Use
the arrow buttons to navigate, and the Select button to select features and
adjust values in the menus. See page 28 for more information on the menus.
The remote also has:
•
•
•
•
•
Source button to switch between sources.
Volume buttons to adjust the sound.
Custom button that can be assigned to a special function, like Blank
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Screen or Freeze (see page 31).
Help button to access the projector’s help feature (see page 34).
Blank button to blank the screen.
24
Using the audio
system and connect the audio directly from your source to a stereo or home
theater system.
Using the projector’s speakers
NOTE: DisplayLink and HDMI audio are passed to the Audio Out
connector.
When the computer is using the DisplayLink or HDMI connectors, both
audio and video are sent over the respective cable to the projector and audio
will play from the projector's speakers.
For inputs other than DisplayLink and HDMI, connect the audio source to
the associated audio connectors in order to use the projector's speakers.
Connect audio cable
audio 5
To adjust the volume, press the Volume buttons on the keypad or remote.
audio 4
L
L
R
R
audio 3
L
audio 1
R
audio 2
audio out
screen trigger
12V DC
250 mA
IR
wireless
ready
DisplayLink
TM
certified
+5V DC; 2A
video 5
serial
video 4
LAN
monitor out
Troubleshooting Audio
If you aren’t hearing the audio, check the following:
•
If your computer is using the projector's DisplayLink connector, see the
InFocus DisplayLink Software User's Guide on the website at
www.infocus.com/displaylink for audio troubleshooting information.
•
Make sure the audio cable is connected to the correct audio in
connector, Computer or Video.
•
Make sure the volume is turned up enough. Press the Volume button on
the keypad or remote.
•
Make sure you are connected to the corresponding audio in for your
source. By default, Audio 1 corresponds to VGA 1, Audio 2 corresponds
to VGA 2, Audio 3 corresponds to Component, Audio 4 corresponds to Svideo and Composite, and Audio 5 corresponds to RGBHV/YPbPr. You
can change these assignments, see page 32.
•
Make sure that you are connected to an audio out connector on the
source as opposed to a line in or microphone connector.
•
Adjust the audio source.
•
If playing a video, make sure the playback has not been paused.
LitePort
computer 1
DisplayLink
computer 4
V
video 3
H B
G
R
computer 3
computer 2
Y
Pb Pr
remote
Adjust volume
External speakers
with own power
source
Connecting external speakers
The projector can be attached to external amplified
speakers
connecting
T
HET
RU
S
T
E
DS
Oby
URC
EF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
a 3.5mm stereo audio cable from the Audio Out connector on the projector to
the amplified speakers. Alternatively, you can bypass the projector’s audio
25
audio 5
audio 4
L
L
R
R
audio 3
L
audio 1
R
audio 2
audio out
screen trigger
12V DC
250 mA
IR
wireless
ready
DisplayLink
TM
certified
+5V DC; 2A
video 5
serial
video 4
LAN
monitor out
LitePort
computer 4
V
H computer 1
DisplayLink
video 3
B
G
R
computer 2
computer 3
Y
Pb Pr
remote
Speaker
cable
Using the keypad buttons
Optimizing computer images
Most buttons are described in detail in other sections, but here is an
overview of their functions:
After the projector is running and the image is on the screen, you can
optimize the image using the onscreen menus. For general information on
using the menus, see page 28.
Power–turns the projector on and off (page 10).
Auto Image–resynchronize the projector to the source.
Presets–cycles through the available preset settings (page 29).
Menu–opens the onscreen menus (page 28).
Select–confirms choices made in the menus (page 28).
Up/Down/Left/Right arrows–navigates to and adjusts settings in the menus
(page 28).
Source–changes the active source (page 10).
•
Adjust the Keystone, Contrast, or Brightness in the Basic Picture menu
(page 29).
•
Change the Aspect Ratio. Choose the option that best fits your input
source (page 29).
•
Adjust the Color Temperature in the Advanced Picture menu
(page 30).
•
Adjust the Phase, Tracking, or Horizontal or Vertical position in the
Advanced Picture menu (page 30).
•
Once you have optimized the image for a particular source, you can
save the settings using Presets. This allows you to quickly recall these
settings later (page 29).
•
If your computer is using the projector's DisplayLink connector, see the
InFocus DisplayLink Software User's Guide for information about
optimizing images.
Help–button to access the projector’s help feature (page 34)
Presentation features
Several features are provided to make giving presentations easier. Here is
an overview, details are found in the menu section.
Menu navigation
buttons
•
The Custom key allows you to assign various features to the button.
The default effect is Source Info, which displays information about the
projector and current source. See page 31 for details.
•
The Search Screen option lets you change the appearance of the blank
screen and start up screen (page 32).
•
Two options, Auto Off and Screen Save Time, are provided to
automatically shut down the projector after several minutes of
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
inactivity or display a black screen. This helps preserve lamp life
(page 31).
26
Optimizing video images
Dynamic Messaging
After your video device is connected properly and the image is on the
screen, you can optimize the image using the onscreen menus. For general
information on using the menus, see page 28.
Using command codes, text messages can be sent for display by the
projector (and all other InFocus projectors with the Dynamic Messaging
feature) over a network or serial connection. Text is shown on top of
whatever else is being displayed, and can be shown in ticker tape format or
in a box, with optional beep tone alert. This is a great way to display urgent
alert messages to employees, and simply requires a connection to the
projector’s RS-232 serial control or LAN connector. Command codes for
executing Dynamic Messaging are in the Appendix and available on our
website at www.infocus.com/support.
•
•
•
•
Adjust the Keystone, Contrast, Brightness, Color, Tint or Sharpness in
the Basic Picture menu (page 29).
Change the Aspect Ratio. Choose the option that best fits your input
source (page 29).
Adjust the Color Temperature. Select a listed warmth value (page 30).
Turn on Overscan to remove noise on the edges of the image (page 30).
Customizing the projector
You can customize the projector for your specific setup and needs. See
page 31 to page 32 for details on these features.
•
•
•
•
•
•
•
•
For rear projection, turn Rear Project on in the Setup menu.
For ceiling mounted projection, turn Ceiling Mount on in the Setup
menu.
Specify which source the projector checks first for active video during
power-up.
Specify the function of the Custom key on the remote.
Turn the projector’s display messages on and off.
Turn on power saving features.
Specify appearance of blank screen and startup screen.
Specify the language viewed on the menus.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
27
Using the menus
To open the menus, press the Menu button on the keypad or remote. (The
menus automatically close after 60 seconds if no buttons are pressed.) Use
the arrow buttons to move up and down to highlight the desired menu,
then press the Select button.
To change a menu setting, highlight it, press Select, then use the arrow
buttons to adjust the value or select an option or turn the feature on or off.
Press Select to confirm your changes. Use the arrow buttons to navigate to
another setting. When your adjustments are complete, press Menu to access
a different menu; press the Menu button at any time to navigate to the
higher-level menu and ultimately close the menus.
Menu navigation
buttons
The menus are grouped by usage:
•
The Basic Picture menu provides common image adjustments.
•
The Advanced Picture menu provides more complex image
adjustments.
•
The Setup menu provides set-up type adjustments that are not changed
often.
•
The Status and Service menu provides information about the projector
and source.
Basic Picture menu
Setup
menu
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPS
AND
ACCE
S
S
ORI
E
S
28
Advanced Picture menu
Status and Service menu
Basic Picture menu
Horz/Vert Keystone: Adjusts the image horizontally or vertically and makes
a squarer image.
To adjust the following settings, highlight the setting, press Select, use the
arrow buttons to adjust the values, then press Select to confirm the changes.
Digital Zoom: Changes the size of projector’s display area. If the display area
has been resized by this setting, it can be moved by changing the Horz Shift
and Vert Shift settings.
Brightness: Changes the intensity of the image.
Contrast: Controls the degree of difference between the lightest and darkest
parts of the picture and changes the amount of black and white in the
image.
Horz Shift/Vert Shift: Moves the display area horizontally or vertically if its
size has been changed by the Digital Zoom setting.
Sharpness: Changes the clarity of the edges of a video image. Select a
sharpness setting.
Color: Adjusts a video image from black and white to fully saturated color.
The color setting applies to video sources only.
Tint: Adjusts the red-green color balance in the image of NTSC video
images. The tint setting applies to NTSC video sources only.
SplitScreen: Allows two distinct sources to be displayed simultaneously.
Switch primary sources, make picture adjustments and choose one of
multiple display options: either two side by side horizontal or vertical
source regions, or a small secondary source image displayed on top of the
primary source in one of four placement options. See page 46 for display
options.
Basic Picture menu
Auto Image: Forces the projector to reacquire and lock to the input signal.
This is useful when signal quality is marginal.
Aspect Ratio: Aspect ratio is the ratio of the image width to image height. TV
screens are usually 4:3. HDTV and most DVDs are 16:9.
Aspect ratio
Select Auto to have the projector choose the ratio. Choose Native to see the
unmodified input with no resizing by the projector. Select 16:9 to watch
enhanced widescreen DVDs.
For more information regarding Aspect Ratio, see page 15.
Apply Preset...: Presets are provided that optimize the projector for
displaying computer presentations and video images under certain
conditions.
There is also a user-definable preset. To set this
preset,
adjust
the
image
T
HE
T
RUS
T
E
DS
OU
RC
EF
ORand
PROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
select Save User in the Presets menu. You can recall these settings in the
future by selecting the User preset.
Increasing keystone
29
Decreasing keystone
Advanced Picture menu
Set Black Level...: Analyzes the current input image and calculates an offset
value which is then added to the analog to digital converter black level
value. This ensures optimum black level for each analog source.
BrilliantColor™: Produces an expanded onscreen color spectrum that
delivers enhanced color saturation for bright, true-to-life images. Choose
Normal Look for most video sources and Bright Look for most computer
sources.
Detect Film: Controls film mode detection, and determines whether the
original source of the input video was film or video.
White Peaking: (video sources only) Increases the brightness of whites that
are near 100%.
Gamma: Select the appropriate gamma from among Video, Film, Bright, and
CRT.
Color Temperature: Changes the intensity of the colors. Select a listed
relative warmth value.
Color Gamut: Sets the color gamut of the input signal.
Force Wide: When this is off, the analog locking algorithms choose the
standard mode resolution (4:3) as the preferred default resolution. When
this is on, the analog locking algorithms choose wide mode resolution
(16:10) as the preferred default resolution.
Color Offset: Adjusts the offset of the red, green, or blue channel of the
image.
Overscan: Removes noise around the video image.
Horizontal/Vertical Pincushion: Correct optical pincushion distortion.
Phase: Adjusts the horizontal phase of a computer source.
.
Color Gain: Adjusts the gain of the red, green, or blue channel of the image.
Horizontal/Vertical Position: Adjusts the position of a computer source.
Sync Threshold: (progressive signals only) If a hardware device, such as a
DVD player, is not syncing properly with the projector, select this option to
help it to sync when connected to the projector.
Tracking: Adjusts the vertical scan of a computer source.
Color Space: This option applies to computer and component video sources.
It allows you to select a color space that has been specifically tuned for the
input signal. When Auto is selected, the projector automatically determines
the standard. To choose a different setting, turn off Auto, then choose RGB
for computer sources or choose either REC709 or REC601 for component
video sources.
Advanced Picture menu
Noise Reduction: Reduces temporal and/or spatial noise in the image.
Flesh Tone Correction: Controls the amount of flesh tone correction applied
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
to the image.
30
Setup menu
AV Mute: Enables or disables AV Mute function.
Source: Cycles through available sources.
Closed Captions: Enables or disables Closed Captions.
SplitScreen: Enables or disables SplitScreen. Before using this for the
first time, configure SplitScreen sources and layout using the
SplitScreen menu (page 29).
Blank Key: Select what to display when the blank key on the remote is
pressed: your custom snapshot, a solid color screen (blue, black or white),
the factory logo screen, a timer, or test patterns. The timer option is useful
for classroom tests or break times during meetings.
•
•
•
•
Language: Allows you to select a language for the onscreen display.
Network: Allows you to setup network settings. See page 35 for details on
network configuration and operation.
•
DHCP: Turns the DHCP on or off.
•
IP Address: Assign Network IP Address.
•
Subnet Mask: Assign Network Subnet Mask.
•
Default Gateway: Assign Network Default Gateway.
•
WINS Host Name Lookup: Turns WINS Host Name Lookup on or off.
•
Host Name: Displays the host name.
•
MAC Address: Displays network MAC Address value.
•
Show Network Messages: Turns network messages on or off. Network
messages display the projector’s IP address (and host name if enabled)
when the projector is also displaying source messages.
•
Restart Network…: Restarts the network.
•
Network Factory Reset…: Performs factory reset.
Source Key Enable: Enables or disables Source Keys on the optional
Commander-2 remote.
AC Power On: When this feature is on, the projector automatically turns on
when electrical power is connected. This allows control of ceiling mounted
projectors with a wall power switch.
Auto Off Time: Automatically turns the projector off after no signals are
detected for a preset number of minutes. If an active signal is received
before the projector powers down, the image will be displayed.
Key Click: Turns the key click sound on or off. When this setting is on,
pressing keys on the keypad causes the projector’s speaker to play a “click”
sound.
Screen Save Time: Automatically blanks the screen with a black color after no
signals are detected for a preset number of minutes. The image returns
when an active source is detected or a remote or keypad button is pressed.
Custom Key: Allows you to assign a different function to the Custom button,
allowing you to quickly and easily use the effect. Highlight an effect and
press Select to choose a different one.
Sleep Timer: Allows the projector to automatically power off after it has been
on for a specified amount of time.
•
•
•
•
•
•
•
•
Always-On Functions: Allows you to control which projector functions will
work even when the projector is in standby (powered off but connected to
Source Info: The default action. Shows the Source Info menu.
AC Power). Press Up or Down to highlight the function you want to
Projector Info: Shows the Projector Info menu.
change, then press select or left and right to change the function to either
Aspect Ratio: Sets the ratio of image width to image height (see page 15
Yes or No. Press menu when done. Note that some functions must always
and page 29).
have the same value; in this case when you change one value, other values
in the submenu may also change automatically.
Auto Image: Resynchronizes the projector to the source (page 26).
Overscan: Removes noise around the image.
Lamp
Low
Power:
between
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMP
SANDToggles
ACCE
S
S
O
RI
E
S on and off. Turn it on to lower the light
output of the lamp. This also lowers the fan speed, making the projector
Blank Screen: Displays an empty screen.
quieter.
Freeze Screen: Pauses the projected image.
Mute: Turns off all sound.
31
Power Sounds: Controls whether the projector makes a sound when
powered on and off.
Auto Keystone: Automatically adjusts vertical keystoning.
Prevent PC Screen Saver: Prevents your computer from going into Screen
Save mode. The projector must be connected to the PC via a USB cable for
this feature to work.
Internal Speakers: Allows the user to turn on and off the internal speakers.
Audio Inputs: Assign an audio input to a specific video/computer source
input. (Default settings are as follows: Audio 1 is used with VGA 1; Audio 2
is used with VGA 2; Audio 3 is used with Component; Audio 4 is used with
S-video and composite; Audio 5 is used with RGBHV/YPbPr.)
Search Screen: Allows you to display a blank screen instead of the default
screen at startup, and when no source is detected. Options include the
factory logo screen, a custom Snapshot, or a blue, black or white screen.
Press up or down to highlight the source you want to change, then press
select or the left and right arrow keys to change that source’s audio input.
Press menu when done changing audio inputs.
Take Snapshot...: Captures the current image and allows it to be used as the
search screen image.
Disable Snapshot: Allows the user to disable the snapshot capability.
Auto Source: When this feature is On, the projector automatically finds the
active source, checking the selected Power-up Source first. When this feature is Off, the projector defaults to the source selected in Power-up Source.
To display another source, you must manually select one by pressing the
Source button on the remote or keypad.
Show Messages: Displays status messages (such as “Searching”) in the lowerleft corner of the screen.
Menu Offset: Allows you to change the position of the On Screen Display
items.
Power-up Source: Determines which source the projector checks first for
active video during power-up.
Menu Transparency: Allows you to change how much of the projected image
behind the menu you can see. As the value increases, more of the image
behind the menu is visible.
Fast Color Refresh: Controls color wheel speed.
Video Standard: When this feature is set to Auto, the projector attempts to
automatically pick the video standard based on the input signal it receives.
(The video standard options may vary depending on your region of the
world.) If the projector is unable to detect the correct standard, the colors
may not look right or the image may appear “torn.” If this happens,
manually select a video standard by selecting NTSC, PAL, or SECAM from
the Video Standard menu.
Magnify Controls: Allows you to change the function of the arrow buttons
when the menu is not shown. By default, the arrow buttons allow you to
advance slides while in PowerPoint’s SlideShow mode. To make the arrow
buttons also adjust magnify settings, choose Magnify Controls to turn
magnify controls on. Now when the menu is not shown, you can press the
Select button to switch between the magnification settings (Magnify Level,
Magnify Horizontal Position and Magnify Vertical Position), then press
Select again to turn off magnify controls and use the arrow buttons to
advance slides.
Closed Captions: Controls closed caption display while audio is not muted. If
this setting is not off, and audio is not muted, and the source is NTSC and
contains captions on the selected channel, then the projector must display
caption text overlaid on the image.
Lens Adjust Enable: When turned on, digital keystone, auto keystone and
pincushion adjustments can be made. When the product has been mounted,
Ceiling Mount: Turns the image upside downT
for
ceiling-mounted
projection.
H
ET
RUS
T
E
DS
OURCE
F
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
installers can turn this feature off to prevent changes to keystone and
Rear Project: Reverses the image so you can project from behind a
pincushion settings.
translucent screen.
Keypad Enable: Enables or disables keypad.
32
Glow Ring: Controls the brightness level of the glow ring status indicator.
PIN Protect: The PIN (personal identification number) feature allows you to
password protect your projector. Once you enable the PIN feature, you
must enter the PIN before you can project an image. The default PIN on this
projector is Menu-Up-Down-Select-Source. Use the navigation buttons on the
remote or keypad to enter the correct 5-button press sequence. When all 5
numbers are entered correctly, press the Select button on the remote or keypad to select OK. If the message “Wrong PIN” appears, verify the code and
re-enter it. If you mis-enter a number, you must enter 5 numbers and press
the Select button in order to access the “Wrong PIN” message and re-enter
the code.
Setup menu
To enter the PIN at projector startup:
Power up the projector. The “Enter PIN” dialog box appears after the
startup screen. Enter the PIN. Use the navigation buttons on the remote or
keypad to enter the correct button press sequence. See the description above
for instructions.
To change the PIN:
Select “Change PIN...” in the Setup menu. Enter the existing PIN. Enter the
new PIN. You can navigate between OK and Cancel by pressing the arrow
buttons on the keypad. Select OK or Cancel by pressing the Select button.
Verify the new PIN.
If you lose or forget your custom PIN:
Contact InFocus support at www.infocus.com/support.
Serial Port, Baud Rate: Selects the serial port and baud rate.
Serial Port Echo: Controls whether the serial port echoes characters.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
33
Status and Service menu
Help
Source Info: Displays current source settings (read-only).
Press Help (on the keypad or remote) at any time to get interactive help for
solving common, picture, sound, and cabling problems.
Projector Info: Displays current projector settings (read-only).
Reset Lamp Hours: Resets the lamp hours used counter in the Projector Info
menu to zero. Do this only after changing the lamp.
Factory Reset: Restores all settings to their default.
Service Code: Only used by authorized service personnel.
NOTE: The projector can be re-programmed to display a custom (non-interactive) screen when Help is pressed. To do this: Create your custom screen
on a computer and display it on the projector, then use the Take Snapshot
command in the Setup menu. When you see the Snapshot Successful message, hold down the Help button until the message is removed.
To revert a customized Help screen back to the InFocus default Help screen,
a Factory Reset will be needed.
Status and Service menu
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
34
Using Network Functions
NOTE: If you still don’t see the IP address, go to the projector’s Setup menu,
select Network, then turn on Show Network Messages. After exiting the
menu press the Source button again.
IMPORTANT: To enable network functions at all times (even when the projector is powered off), the Network item in the Always-On Functions submenu in the Setup menu must be set to Yes (not No).
3 Select IP Address. This will highlight the first of the four octets in the IP
address. Press Up or Down to change the value, then press Select or Right
when done to move to the next octet. Repeat until you have changed all
four octets in the IP address.
Projector network functions include:
•
Configuring and controlling the projector via a web browser.
•
Failure and warning alerts via email.
•
Projector Management via SNMP.
•
Controlling the projector via Scheduling.
4 Repeat the above for Subnet Mask, Default Gateway, and other settings
that are in IP address format (to assign or change the Host Name, see
Network Settings Page below).
Configuring and Controlling the Projector via a Web Browser
NOTE: Projector web pages and emails sent by the projector are always displayed in English language.
You can adjust or control the projector via a network from a web browser
on a computer that is connected to the same network as the projector.
Before using the network functions
NOTES:
To use the network functions of the projector, the projector must be configured to suit your network. Consult with your network administrator before
connecting the projector to your network; incorrect network configuration
of the projector may cause problems on your network.
Connect the Network Cable
Properly connect projector to the network, then configure the following settings.
If Using a Network with DHCP Enabled:
1 Use the projector's remote control or keypad to select the Network item
in the projector's Setup menu.
•
To access the projector’s web pages, the projector must be connected to
the network and connected to AC power (and if you want to access the
web pages even when the projector is powered off, make sure that the
Network item in the Always-On Functions submenu is set to Yes).
•
JavaScript must be enabled in your browser to use the projector web
pages properly. If JavaScript is disabled, see the Help files for your web
browser for details on how to enable it.
•
If no operations are performed in the web browser for approximately
ten minutes, the system will automatically log you off.
Logging in
To log into the projector web pages, follow these steps:
2 If DHCP is off, select it to turn it on.
1 Make sure the projector is connected to the network and connected to
If Using a Network that Does Not have DHCP Enabled:
AC power.
1 Use the projector's remote control or keypad to select the Network item
2RIfL
you
don't
know
the
projector's
IP
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
O
A
MP
SAND
ACCE
S
S
O
RI
E
S
in the projector's Setup menu.
address, turn on the projector. After the
projector starts up, if its IP address is not
shown, press the Source button to view the IP address.
2 If DHCP is on, select it to turn it off.
35
3 Start a web browser on your computer.
NOTE: Unlike other pages, changes you make to Projector Control settings
are applied immediately.
4 Enter the projector's IP address or host name (preceded by http://) into
•
To change an on/off setting (e.g. Power): Click the corresponding On or
Off button.
•
To change a multi-value setting (e.g. Sharpness): Select a value from the
drop-down menu.
6 Select Access type: Basic User or Administrator.
•
7 Click Log In.
To change a numeric setting (e.g. Brightness): Click the corresponding +
or - button, or select a value from the drop-down menu.
•
To perform a command (e.g. Auto Image): Click the corresponding Execute button.
the web browser's address bar. Example: If the IP address is
192.168.1.10, enter http://192.168.1.10 into the browser's address bar.
5 The Log In to Projector Control page will be shown in the browser.
Navigating Projector Web Pages
Network Settings Page (administrators only)
The left side of every page shows a navigation bar. Click the links in the
navigation bar to go to different projector web pages.
This page lets you view and change the projector's network settings. Consult with your network administrator before making any changes on this
page; incorrect network configuration of the projector may cause problems
on your network.
NOTE: If a Basic User is logged in, no links are shown.
The top of the navigation bar shows the projector name, model, and serial
number.
Projector Name: The name of the projector shown in the projector's web
pages.
The web pages also include the following options:
•
Log Off: Logs off and returns to the Log In page (see above).
•
Refresh: Reloads the page with current status.
•
Defaults: Displays default (factory settings) values (to save these values
click Apply).
•
Apply: Saves the values that are currently shown on the page.
IP Address: These settings control the projector's network configuration.
Enter the appropriate settings required for your specific network.
Advanced Network Settings: Click this link to show advanced settings.
802.1x Authentication: If your network requires 802.1x authentication, enter
the user name and password that the projector should use, and select the
authentication type.
Projector Controls Page (All users)
This page lets you control the same settings that are available via the projector's main menu and remote control. The Controls tab includes basic remote
control functions; other tabs correspond to the projector's menus.
SNMP: If your network uses SNMP, enter necessary SNMP information
here.
Command and Control Pass-Through: This setting allows you to send and
receive projector commands over the network. For command codes, see the
Appendix or visit the InFocus website at: www.infocus.com/support.
NOTE: If a Basic User is logged in, only the Controls, Basic Picture, and
Advanced Picture tabs are shown.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
In each tab, the current value of each setting is shown in blue color.
36
Event Notifications Page (administrators only)
Daylight Savings Settings: Click this link to show daylight savings settings:
This page lets you configure the projector to automatically send email when
specific events occur.
Start: Select when daylight savings starts.
End: Select when daylight savings ends.
E-Mail Settings tab: In the Account Used… section, enter the information
needed for your projector to connect to an email sending (SMTP) server.
Then in the Recipient E-Mail Addresses section, enter the email addresses of
people who will receive emails, and for each address, select whether that
address receives reminders and/or warnings and errors (enter only one
address per line). After you have completed this page, click Send Test to
make sure that email is correctly set up.
Automatically adjust…: Check this to have the projector automatically update
time and date when daylight savings starts and ends.
Scheduled Tasks Page (administrators only)
This page lets you configure the projector to perform tasks automatically on
specific days and times. You can set up a maximum of three different scheduled tasks; each tab corresponds to a task. Each scheduled task can perform
different commands on different days and times. Each tab contains the following items:
Reminders tab: Select which types of reminders to send. For most reminders,
you can adjust the frequency or date/duration associated with the
reminder.
Warnings & Errors tab: Select which warnings and errors to send.
On/Off: Select whether or not this scheduled task will run on the days and
times shown.
Date/Time Settings Page (administrators only)
Description: Explanation of what the task does.
This page lets you configure the projector to read the time and date from an
SNTP server on your network. NOTE: The projector does not have a built-in
clock. If the projector is unable to access the SNTP server, or no SNTP server
is defined, functions that rely on the time and date may not work correctly.
Run Every: Select the days of the week when the scheduled task should run.
At Time(s): Select the times of day when the scheduled task should run (the
task will run at the indicated times on every one of the days checked above).
Current Date and Time: Shows the current date and time read from the SNTP
server.
Command Sequence and Available Commands: The Command Sequence list on
the left shows commands currently performed by the scheduled task (each
task can include up to 20 commands). The Available Commands list on the
right shows all commands that can be added to a scheduled task.
Synchronize the system clock…: Select how often the projector should check
the SNTP server to get the time and date. Between checks, the projector will
keep track of the amount of time elapsed, allowing it to maintain the correct
time and date.
<< Add: Adds the command selected in the Available Commands list to the
Command Sequence list.
SNTP Server: The address of the time and date server on your network.
>> Remove: Removes the command selected in the Command Sequence list.
Time Zone: The projector's time zone (if you are in a different time zone
Move Up: Moves up the command selected in the Command Sequence list.
from the projector, make sure this is the time zone of the region where the
Move Down: Moves down the command selected in the Command Sequence
projector is located).
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
box list.
Set Now: Click this to immediately set the time and date based on the above
Clear All: Erases all commands in the Command Sequence list.
information.
37
Custom: Click this link to show custom command entry options. With custom commands, you can perform additional commands not shown in the
Available Commands list. The RS-232 command codes are available in the
Appendix and on our website at www.infocus.com/support.
This lets you quickly 'clone' network settings from one projector to other
projectors.
Upgrade Projector Network Firmware: Upgrades the firmware for the projector's network and LitePort features (this firmware is separate from the regular projector firmware).
NOTE: Custom commands you enter here should be in write format (do not
include '?'), and should use '<' and '>' instead of '(' and ')'. Example: to turn
on the ceiling mount setting, use the custom command <CEL1>.
Restart Projector Network Subsystem: Restarts the projector network subsystem; does not change any projector settings.
User Access and Security Page (administrators only)
Network Subsystem Factory Reset: Returns all network and LitePort settings
to default values and then restarts the projector network subsystem.
This page lets you configure security options for the projector, including log
in passwords and projector access restrictions.
Troubleshooting Network Functions
Web Access - Administrator tab: Select whether or not Administrators must
enter a password to log into the projector's web pages. If a password is
required, click create or change password to update the administrator password.
Web Access - Basic User tab: Select whether or not Basic Users must enter a
password to log into the projector's web pages. If a password is required,
click create or change password to update the basic user password.
Projector PIN tab: Allows you to turn projector PIN protection on or off, or
change the PIN. When PIN protection is on, the current PIN must be
entered when the projector is powered on, otherwise the projector will not
operate. NOTE: PIN protection only applies to projector operation via the
projector's keypad and remote control; it does not affect the projector's web
pages.
System Log Page (administrators only)
This page shows a log of the 100 most recent projector events.
Erase Log…: Click this to erase all events in the log.
•
If network status is shown as Not Connected in the projector's Network
menu, or the projector does not display its IP address, check the cable
or the network configuration.
•
If your web browser displays Page Not Found or a similar error when
you try to access the projector's web pages, verify that the
projector is connected to the network (select the Network item in the
projector's Setup menu and verify that Network Status shows as
Connected); if there is no connection refer to the troubleshooting item
above for more help.
•
Make sure the Network item in the Always-On Functions submenu in
the Setup menu is set to Yes (if it is set to No, the projector web pages
will only be available when the projector is powered on).
•
If scheduled tasks are not performed, check if the SNTP is set up correctly and is online. Also check if the Command sequence is correct.
•
If automatic emails are not sent, check if SMTP is set up correctly and is
online.
To manually restart the projector network subsystem: Use the projector's
remote control or keypad to select the Network item in the projector's Setup
This page lets you perform various network-related projector tasks.
menu. Then scroll down and select either Restart Network (to restart the
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMsubsystem
PSANDAC
CE
S
S
ORI
E
S
network
without
changing
any settings), or Network Factory
Save and Load Projector Configuration: These functions save and load all netReset
(to
return
all
network
settings
back
to default values, and then restart
work-related projector settings into/from a file stored on your computer.
the network subsystem). If the manual restart procedure does not work: To
Network Utilities Page (administrators only)
38
force the network subsystem to restart, disconnect the projector from AC
power, wait 10 seconds, then reconnect AC power.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
39
Using LitePort
lighted to start the slide show, or press Select when a folder is highlighted to
open that folder.
LitePort displays a slide show of JPEG images stored on a USB flash drive
connected to the projector. This can eliminate the need for a computer
source.
To start the slide show: While viewing thumbnails, press the arrow buttons
to highlight a thumbnail, then press the Select button to start the slide show
at the highlighted image.
Image File Types
To change the image during the slide show: Press the Down or Right button to
go to the next image, or press the Up or Left arrow button to go to the previous image (the slide show may also advance automatically depending on
the value of the Next Slide setting; see the LitePort Menu section below for
details).
LitePort displays image files in JPEG format only (file extensions .JPEG and
.JPG). Other file types including PDF, BMP, TIFF, PNG, GIF, etc. are
ignored.
Viewing a Slide Show
To view your pictures as a slide show, follow these steps:
To change to a different folder: While viewing thumbnails, press the arrow
buttons to highlight the desired folder icon, then press the Select button (to
go to the higher-level folder, select the folder icon labeled "Up").
1 Connect a USB flash drive to your computer and copy JPEG files from
your computer to the USB flash drive.
2 Turn on your projector if needed.
To change LitePort settings: Press the Menu button during the slide show, or
while viewing thumbnails (see the LitePort Menu section below for details).
3 Remove the USB flash drive from your computer and plug it into the
Using the LitePort Menu
LitePort connector on the rear of the projector.
To show the LitePort menu, press the Menu button on the keypad or remote
during the slide show, or while viewing thumbnails. To highlight a menu
item, press arrow buttons. Then to do the action or change the setting, press
Select. To remove the menu, press the Menu button again.
4 The projector will start a slide show of the images found (if you see
image thumbnails instead, see To Start the Slide Show section below).
5 To go to the next image in the slide show, press the Down or Right
Rotate Picture: Rotates the current image by 90 degrees clockwise (rotation is
temporary; the image returns to its original orientation when the USB flash
drive is removed from the projector or when the projector is turned off).
arrow button on the projector keypad or remote. To go to the previous
image, press the Up or Left arrow button.
Controlling LitePort
Stop/Start Slideshow: Stops the slide show, or starts it at the selected thumbnail (when the menu is not visible, you can also stop or start the slide show
by pressing the Select button).
When you plug a USB flash drive into the projector's LitePort connector, the
projector will scan the drive and then either start a slide show or show
image thumbnails.
Go to Projector Main Menu: Removes the LitePort menu and displays the
projector's main menu, where you can adjust the picture or change other
To stop the slide show and view thumbnails: Press the Select button during the
projector
settings.
slide show. In Thumbnails view, the name of
the
current
the
current
T
H
ET
RUS
T
E
Dfolder,
S
OURC
EF
ORPROJ
E
CT
ORL
AMP
SANDACCE
S
S
ORI
E
S
image number, and the total number of images in that folder are shown at
(For remaining items below, highlight the setting, then press Select one or
the bottom of the screen. While viewing thumbnails, press the arrow butmore times to change the setting value.)
tons to scroll through the thumbnails, or press Select when an image is high-
40
4 Click the Office button in the upper left corner of the PowerPoint docu-
Auto Start: Select On to have the player start the slide show when the USB
flash drive is first connected. Select Off to have the player display thumbnails when the USB flash drive is first connected.
ment window.
5 Point to Save As, then click Other Formats.
Show All Folders: Select On to have the slide show display all images in all
folders. Select Off to have the slide show display images only from the current folder.
6 In the Save As dialog box, click the Save as type drop-down menu. Scroll
through the menu and select JPEG File Interchange Format.
Fill Screen: Select On to have the slide show expand small images to fill the
screen. Select Off to have the slide show display small images at their original size.
7 Make sure the contents of your USB flash drive are visible in the Save As
dialog box before you continue - to view your USB flash drive in the
Save As dialog box, first click My Computer, then double-click the USB
flash drive's icon (make sure you do both of these in the Save As dialog
box, not on your computer's desktop).
Next Slide: Select Manual to disable automatic slide advance in the slide
show. Select other values to make the slide show advance to the next image
automatically (regardless of this setting, manual advance is always available by pressing the arrow buttons).
8 Click Save. PowerPoint will ask if you want to export every slide or only
the current slide; click Every Slide. PowerPoint will save each slide in
your presentation as a separate JPEG file. These files are saved in a new
folder that has the same name as the original document.
Effect: Select Off to have no transition effect when changing between images
during the slideshow. Select Random to use a different random effect for
each transition. Select other values to use a specific effect.
9 Remove the USB flash drive from your computer and plug it into the
Show Info: Select On to show the name of the current file and folder, the current image number, and the total number of images in the slide show at the
bottom of the screen. Select Off to hide this information.
projector's LitePort connector.
10 On the projector, navigate to the folder created in step 8 and then start
Displaying PowerPoint Slides
the slide show (for instructions on navigating and controlling the slide
show, see the Controlling LitePort section above).
Follow the steps below to display PowerPoint slides using LitePort (these
instructions apply to PowerPoint 2007 in Windows; for other presentation
programs refer to the program's instructions or help file for the steps
needed to save a presentation as separate JPEG files):
NOTE: PowerPoint embedded videos, transition effects, and animations are
not included when saving as JPEG. However, you can select a LitePort
slideshow transition effect by changing the Effect in the LitePort menu.
1 Connect the USB flash drive to your computer.
2 Open your PowerPoint document.
3 This step is optional but improves image quality: Click the Design tab
near the top of the PowerPoint document
window,
then
click
Page
T
H
ET
RUS
T
E
DS
O
URC
EF
OSetup.
RPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Click the Slides sized for drop-down menu and select Custom. Change
both Width and Height to double their previous values, then click OK.
41
Troubleshooting LitePort
•
If images load slowly: Make sure you are using a newer USB 2.0compatible (high speed) USB flash drive. Larger image file sizes may
also slow down the player; to reduce file size, use an image editing program on your computer to resize images smaller; for the best balance
between image quality and speed, resize images to be 1024 pixels wide.
•
If no images are found, or some images are not shown, or you only see
folder thumbnails but no images: Make sure that images are JPEG file
type (file extensions .JPEG and .JPG); other file types are not supported
and will be ignored.
•
If you see a blank screen, or a logo, or the wrong input source (computer, video, etc.) instead of your images: Keep pressing the Source
button on the keypad or remote until the LitePort message is displayed
(if you still don't see any images, make sure the USB flash drive is correctly and completely plugged into the projector's LitePort connector).
•
If nothing happens when you connect your USB flash drive, and you
cannot select the LitePort input source as described above: Check the
format of your USB storage device. LitePort only supports USB storage
devices formatted as FAT32. Devices formatted as NTFS, and non-storage devices (such as cameras) are not supported.
•
If images saved by PowerPoint are low quality: Make sure to do step 3
when following the steps in the Displaying PowerPoint Slides section
above.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
42
Maintenance
Cleaning the lens
1 Turn the projector off and unplug the power cord.
2 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
• Avoid using an excessive amount of cleaner, and don’t apply the
cleaner directly to the lens. Abrasive cleaners, solvents or other harsh
chemicals might scratch the lens.
3 Lightly wipe the cleaning cloth over the lens in a circular motion.
WARNINGS:
•
Turn the projector off and unplug power cord before cleaning any part
of the projector.
•
Do not open any cover on the projector, except the lamp cover or
projector top cover.
•
Do not attempt to service this product yourself as opening and removing covers may expose you to dangerous voltage and other hazards.
Refer all servicing to qualified service personnel.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
43
Replacing the projection lamp
1 Turn the projector off and unplug the power cord.
The Lamp Hours timer in the Projector Info menu counts the number of
hours the lamp has been in use. Twenty hours before the lamp life expires,
the message “Replace lamp” appears on the screen at startup.
2 Wait 60 minutes to allow the projector to cool thoroughly.
•
3 Remove the lamp door by removing the screws on the side of the lamp
door, and lifting the door off.
NOTE: Be sure to use the InFocus lamp module designed for this
projector. You can order new lamps from www.infocus.com (in select
areas), your retailer or your dealer. Only genuine InFocus lamps are tested
for use in this projector. Use of non InFocus lamps may cause electrical
shock and fire, and may void the projector warranty. InFocus is not
liable for the performance, safety or certification of any other lamps.
Turn off and
unplug projector
audio 5
L
audio 4
L
audio 3
L
audio 1
R
audio 2
audio out
screen trigger
12V DC
250 mA
R
R
IR
wireless
ready
DisplayLink
TM
certified
+5V DC; 2A
video 5
serial
video 4
LAN
monitor out
LitePort
computer 4
V
H computer 1
DisplayLink
video 3
B
G
R
computer 2
computer 3
Y
Pb Pr
remote
WARNINGS:
•
•
•
•
•
•
•
•
•
The projector uses a high-pressure mercury glass lamp. The lamp may
fail prematurely, or it may rupture with a popping sound if jolted,
scratched, or handled while hot. The risk of lamp failure or rupture
also increases as the lamp age increases; please replace the lamp when
you see the “Replace Lamp” message.
To avoid burns, allow the projector to cool for at least 60 minutes before
you replace the lamp.
Unplug the power cord before replacing the lamp.
Do not drop the lamp module. The glass may shatter and cause injury.
Do not touch the glass surface of the lamp module. Fingerprints can
obscure projection sharpness and may cause the glass to shatter.
Be extremely careful when removing the lamp housing. In the unlikely
event that the lamp ruptures, small glass fragments may be generated.
The lamp module is designed to contain most of these fragments, but
use caution when removing it.
Before replacing a ruptured lamp, clean the lamp compartment and
dispose of cleaning materials. Wash hands after lamp replacement.
When replacing the lamp while the projector is ceiling-mounted, wear
protective eyewear to prevent eye injury.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Hg – Lamp contains mercury. Manage in accordance with local
disposal laws. See www.lamprecycle.org.
44
Wait 60
minutes
4 Loosen the captive screws that attach the lamp housing to the projector.
5 Using the handle, carefully remove the lamp housing. Dispose of the
lamp in an environmentally proper manner in accordance with local
disposal laws.
6 Install the new lamp housing, pressing the lamp into place.
7 Tighten the captive screws.
8 Replace the lamp door and tighten both screws.
9 Plug in the power cord and press the Power button to turn the projector
back on.
10 To reset the lamp hour timer, navigate to the Status and Service menu and
select Reset Lamp Hours. See page 34 for details.
Using the security lock
The projector has a security lock for use with a Cable Lock System. Refer to
the information that came with the lock for instructions on how to use it.
Security lock
audio 5
audio 4
audio 3
L
L
L
audio 1
audio out
R
R
R
audio 2
IR
screen trigger
12V DC
250 mA
wireless
ready
DisplayLink
TM
certified
+5V DC; 2A
video 5
serial
video 4
LAN
monitor out
LitePort
computer 4
V
H
computer 1
DisplayLink
video 3
B
G
R
computer 2
computer 3
Y
Pb
Pr
remote
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
45
Appendix
SplitScreen Compatibility
Splitscreen allows two distinct sources to be displayed simultaneously. Switch primary sources, make picture adjustments and choose one of multiple display options: either two side by side horizontal or vertical source regions, or a small secondary source image displayed on top of the primary source in one
of four placement options.lets you show two different sources at the same time. See page 29 for details. The following source combinations are supported:
Table 4:
HDMI1
HDMI1
HDMI2
VGA1
VGA2
BNC
Component
S-video
Composite
DOUSB
LitePort
HDMI2
X
X
VGA1
X
X
X
RGBHV
X
S-video
X
Composite
X
DOUSB
X
LitePort
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Component
X
X
X
X
X
X
X
X
X
VGA2
X
X
X
X
X
X
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
46
RS-232 commands
(AAA?) where
(starts the command
AAA denotes the command
? denotes the read request
) ends the command
IMPORTANT: When formatting commands sent from a control system or
computer, enclose commands in parentheses “(“ and “)”. When entering
custom commands into Scheduled Tasks in the projector’s web interface,
enclose commands in less than/greater than symbols “<” and “>” instead.
A read command returns the range and the current setting, for example:
Communication Configuration
Visit our website for additional RS-232 settings and information.
Read Command Examples
To control this projector via RS-232, connect a null modem cable and set the
control system serial port settings to match the following communication
configuration:
Function
Brightness
(BRT?)
(96-160,128)
RS-232 Port Settings
Volume
(VOL?)
(0-32, 0)
Setting
Value
Bits per second
115,200
Data bits
8
Parity
None
Stop bits
1
Flow control
None
Emulation
VT100
Lamp Hours
(LMP?)
Response
(0-32766, 42)
A write request example:
(AAA####) where
(starts the command
AAA denotes the command
#### denotes the value to be written
(leading zeros not necessary)
) ends the command
Some commands have ranges, while others are absolute. If a number
greater than the maximum range is received, it is automatically set to the
maximum number for that function. If a command is received that is not
understood, a "?" is returned. With absolute settings, "0" is off, 1-9999 is on.
The one exception is the Power command, where 0 is off and 1 is on.
Command Format
All commands consist of 3 alpha characters followed by a request, all
enclosed in parentheses. The request can be a read request (indicated by
a"?") or a write request (indicated by 1 to 4 ASCII digits).
A read request example:
Command
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
OR
L
AMP
SAprojector
NDACCE
S
S
OR
I
E
S a command, wait 3 seconds before enterTo
assure
the
can
process
ing the next command.
47
Read Command Examples
Function
Command
Response
Brightness
(BRT140)
Sets the brightness to
140
Power
(PWR0)
Turns power on
Power
(PWR1)
Turns power off
Error Conditions
Not all commands are supported for all projectors. If an unsupported command is issued, the command will be ignored. If a command is received that
is not understood, a ‘?’ character will be returned indicating the commandwas not understood.
Limitations
The projector cannot respond to commands coming in at a high-rate. Therefore, a delay must occur between commands to ensure that the command
gets properly executed. To assure the projector can process a command,
wait 3 seconds before entering the next command.
The Step column refers to increasing or decreasing the menu bar position
since the On-screen Display is not an exact match of values. For example,
Step 2 changes the data by 2 through the CLI (Command Line Interface).
The menu bar is up (or down) by 1.
Function
Command
Min
Max
Default
About (Source Info)
0: n/a
1: enable
ABT at W
0
1
n/a
Aspect Ratio
0: Native
1: 16:9
2: 4:3
ARZ at RW
0
2
2
Auto Image
0: n/a
1: enable
AIM at W 0
0
1
n/a
Auto Power
0: disable
1: enable
APO at RW
0
1
0
Auto Source
0: disable
1: enable
ASC at RW
0
1
1
Blank
0: off
1: on
BLK at RW
0
1
0
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
48
Step
Blank Screen
0: black
1: blue
2: white
BSC at RW
0
2
1
Blue Gain
BCG at RW
64
192
128
1
Brightness
BRT at RW
96
160
128
1
Ceiling
0: disable
1: enable
CEL at RW
0
1
0
1
Color
CLR at RW
96
160
128
1
Color Space
0: Auto
1: RGB
2: REC709
3: REC601
4: RGB Video
CSM at RW
0
4
0
Color Temp
0: 9300K
1: 6500K
2: 7200K
3: User
TMP at RW
0
3
2 (computer
2,3)
0 (other)
Contrast
CON at RW
96
160
128
Custom Key
(Effect)
0: blank
1: mute
2: aspect ratio
3: source
4: auto image
5: freeze
6: zoom
7: Source Info
8: Service Info
15: AV Mute
17: SplitScreen
EFK at RW
0
15
7
Display Messages
0: disable
1: enable
DMG at RW
0
1
1
Factory Reset
0: not reset
1: reset
RST at W
0
1
n/a
Freeze
0: disable
1: enable
FRZ at RW
0
1
0
Green Gain
GCG at RW
64
192
28
1
Horizontal
Keystone
DKH at RW
38
218
128
1
HDMI Noise
Cancel
HNC at RW
0
1
1
Horizontal Position
HPS at RW
def: -128
def:+128
auto
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
49
1
Internal Sound
Enable
0: disable
1: enable
INT at RW
0
1
1
IR Receiver front
0: disable
1: enable
IRF at RW
0
1
1
IR Receiver rear
0: disable
1: enable
IRR at RW
0
1
1
IR Receiver top
0: disable
1: enable
IRT at RW
0
1
0
Language
0: English
1: French
2: German
3: Italian
5: Korean
6: Norwegian
7: Portuguese
8: Russian
9: Simplified
Chinese
10: Spanish
11: Traditional
Chinese
12: Swedish
13: Dutch
14: Polish
15: Turkish
16: Danish
17: Finnish
LAN at RW
0
17
0
Lamp Hours
LMP at R
Lamp Lit
0: not lit
1: lit
LML at R
0
1
Reset Lamp Hours
0: not reset
1: reset
LRT at W
0
1
n/a
Number of Lamp
Resets
LMR at R
0
32766
0
Lamp Total On
Time (All Bulbs)
LMT at R
0
21474
83646
0
Time In Hours Last
Bulb1 Lasted
LB1 at R
0
32766
0
Time In Hours Last
Bulb2 Lasted
LB2 at R
0
32766
0
Time In Hours Last
Bulb3 Lasted
LB3 at R
0
32766
0
Low Power
0: disable
1: enable
LPE at RW
0
1
0
Magnify
MAG at RW
0
48
0
Magnify Enable
0: disable
1: enable
MGE at RW
0
1
0
Magnify Position
Horizontal
MPH at RW
0
64
32
1
Magnify Position
Vertical
MPV at RW
0
64
32
1
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
0
32766
0
1
50
1
Menu
0: disable
1: enable
MNU at RW
0
1
0
Menu Navigation
0: up
1: down
4: select
NAV at W
0
4
n/a
Mute
0: disable
1: enable
MTE at RW
0
1
0
Network Restart
0: not restart
1: restart
NTR at W
0
1
n/a
NND (PC Screen
Saver Off)
0: disable
1: enable
NND at RW
0
1
1
Overscan
0: disable
1: enable
OVS at RW
0
1
0
Phase
MSS at RW
0
31
0
Power
0: disable
1: enable
PWR at RW
0
1
0
Power Save
0: disable
1: enable
PSV at RW
0
1
0
1
Power-up Source
0: DisplayLink
1: VGA 1
2: VGA 2
3: RGBHV
4: HDMI 1
5: HDMI 2
6: Component
7: S-video
8: Composite
DSC at RW
0
5
1
Presets
0: user 1
1: user 2
2: user 3
3: Presets Off
5: presentation
7: video
10: bright
11: whiteboard
PST at RW
0
11
computer
2,3:5
computer 1,
video:7
Rear
0: disable
1: enable
REA at Rw
0
1
0
Red Gain
RCG at RW
64
192
128
Reset Filter Hours
0: not reset
1: reset
FRT at W
0
1
n/a
Save User Presets 1
0: not saved
1: saved
USI at W
0
1
n/a
0
1
n/a
Save User Presets 2
US2 at W
0: not saved
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
OR
L
AMPSANDACCE
S
S
ORI
E
S
1: saved
51
1
Save User Presets 3
0: not saved
1: saved
US3 at W
0
1
n/a
Screen Save
0: 5 minutes
1: 10 minutes
2: 15 minutes
3: 20 minutes
4: 25 minutes
5: 30 minutes
SSV at RW
0
5
0
Sharpness
5: Sharpest
6: Sharper
7: Standard
8: Softer
9: Softest
SHP at RW
Source
0: DisplayLink
1: VGA 1
2: VGA 2
3: RGBHV
4: HDMI 1
5: HDMI 2
6: Component
7: S-video
8: Composite
SRC at RW
0
5
0
Source 1
0: DisplayLink
1: VGA 1
2: VGA 2
3: RGBHV
4: HDMI 1
5: HDMI 2
6: Component
7: S-video
8: Composite
SR1 at RW
Source
2:SR2
Source
3:SR3
0
5
0
1
3
4
5
9
7 (computer
and video 1)
6 (video 2
Audio for Source 0
0: audio 1
1: audio 2
2: audio 3
3: audio 4
4: HDMI Internal
SA0 at RW
0
5
4
Audio for Source 1
0: audio 1
1: audio 2
2: audio 3
3: audio 4
SA1 at RW
Source
2:SA2
Source
3:SA3
Source
4:SA4
0
5
0
1
3
2
2
SplitScreen Enable
0: off
1: on
SSC at RW
0
1
0
SplitScreen Second
Source
0: off
1: DisplayLink
2: VGA 1
3: VGA 2
4: RGBHV
5: HDMI 1
6: HDMI 2
7: Component
8: S-video
9: Composite
SSL at RW
0
6
0
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
52
SplitScreen Second
Source Location
0: right
1: bottom
2: left
3: top
4: bottom right
5: bottom left
6: top left
7: top right
SSY at RW
SplitScreen Second
Source Size
0: small
1: medium
2: large
SSZ at RW
0
2
2
SplitScreen Swap
0: n/a
1: enable
SSS at W
0
1
n/a
Startup Logo
0: blank screen
1: default
2: captured
SHP at RW
5
9
Tint
TNT at RW
96
160
128
1
Tracking
MTS at RW
def: -384
def:+384
auto
1
Unit Total Time On
ONL at R
0
21474
83646
0
Vertical Keystone
DKC at RW
38
0
7
0
Vertical Position
VPS at RW
if def <
128:0
else: def
- 128
def +128
auto
Video Standard
0: Auto
1: NTSC
2: PAL
3. SECAM
VSU at RW
0
3
0
Volume
VOL at RW
0
32
16
Sync on Green
0: Sunc on G off
1: Auto
T
H218
ET
RUS
T
E
D
S
OURCEF
ORP
OJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
128
1R
53
1
1
INDEX
Numerics
16x9 vs 4x3 15
A
Aspect Ratio 15
Audio In Computer connector 11
Audio Out connector 25
C
Cable box 14
Computer In connector 10
Connecting
external speakers 25
Connecting
computer 10
video device 14
Connecting a computer source 10
Contacting InFocus 23
Customer service contact information 23
D
Digital Zoom 29
Displaying an image 12
Dynamic Messaging 27
F
Focus 13
H
HDTV 4
Help 34
K
Keypad buttons 26
Keystone 20
L
Laptop video port activation 12
LitePort
Using LitePort 40
M
Menu usage 28
Monitor Out connector 11
N
Network
Using Network Functions 35
O
Optimizing computer image 26
Optimizing video images 27
P
Position the projector 7
Power connector 10
Power cord 10
Presentation features 26
Projector
keypad buttons 26
menus 28
Projector
connecting computers 10
connecting video devices 14
positioning 7
setting up 7
shutting down 16
troubleshooting problems 16
R
Remote control 24
S
Scheduled Tasks Page 37
Screen Aspect 15
Screen Save 16
Shutting down the projector 16
Speakers, connecting external 25
S-video connector 14
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
AMPSANDACCE
S
S
ORI
E
S
TORL
Troubleshooting Network Functions 38
TV tuner 14
54
U
USB 11
User Access and Security Page 38
V
Viewing a Slide Show 40
Volume button 25
W
Warranty 23
Z
Zoom 13
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
55
Disclaimer
This user manual is provided as a free service by FixYourDLP.com. FixYourDLP is in no way responsible
for the content of this manual, nor do we guarantee its accuracy. FixYourDLP does not make any claim
of copyright and all copyrights remain the property of their respective owners.
About FixYourDLP.com
FixYourDLP.com (http://www.fixyourdlp.com) is the World’s #1 resource for media product news,
reviews, do-it-yourself guides, and manuals.
Informational Blog: http://www.fixyourdlp.com
Video Guides: http://www.fixyourdlp.com/guides
User Forums: http://www.fixyourdlp.com/forum
FixYourDLP’s Fight Against Counterfeit Lamps:
http://www.fixyourdlp.com/counterfeits
Sponsors:
RecycleYourLamp.org – Free lamp recycling services for used lamps:
http://www.recycleyourlamp.org
Lamp Research - The trusted 3rd party lamp research company:
http://www.lampresearch.com
Discount-Merchant.com – The worlds largest lamp distributor:
http://www.discount-merchant.com
Sponsored by DM
Download PDF
Similar pages