Operation and Maintenance Manual

Operation and
Maintenance Manual
Schrader - Air solutions since 1844
Model #:
Serial #:
SA2560V
SA2580V
SA27580V
SA788B
SA788BE
SA788H
SA6830B
SA6830H
SA61030B
SA61130H
SA27580V
SAFETY INSTRUCTIONS FOR ELECTRIC AND GAS AIR COMPRESSORS
When using air compressors and compressed air accessories,
basic safety rules and precautions should always be followed
including the following:
1. Read all instructions fully before operating this
compressor.
2. Never use a compressor that is defective, operating abnormally, making strange noises, or otherwise appears defective. Stop using compressor immediately and arrange for repairs by an authorized service center.
3. Do not modify compressor. Always contact the SchraderAir
authorized service center for any repairs.
4. Use only Manufacturer’s Air Compressor replace
ment parts.Replacement parts not manufactured by Manufacturermay void your warranty and can lead to compressor malfunction and personal injuries.
5. Wiring, starters, breakers and other related electrical equipment should conform to electrical codes when
operating any electric air compressors. Electrical
connections should be made by a competent electrician.
6. Always disconnect compressor from its power source and remove the compressed air from the tank before
servicing, inspecting, cleaning, replacing, or checking any parts.
7. Do not operate compressor without belt guard. If
maintenance or servicing requires the removal of a guard or safety feature, be sure to replace the guard or safety feature before resuming operation of the
compressor.
8. Do not use gasoline compressor if Load Genie does not operate properly. Have defective Load Genie replaced by an authorized service center.
9. Avoid unintentional starting. Do not move the
compressor while connected to its power source or when the air tank is filled with compressed air. Be sure the knob of the pressure switch is in the “OFF” position before connecting compressor to its power source.
10.Turn off the compressor when not in use. Then open the drain cock to discharge the compressed air from the air tank.
11. Do not expose compressor to rain. The compressor should be stored in a dry place.
12. Do not use compressor in the presence of flammable liquids or gases. Compressor can produce sparks during operation. Never use compressor in sites containing
lacquer, paint, benzine, thinner, gasoline, gases,
adhesive agents and other materials, which are
combustible or explosive.
2
13. Use only recommended air handling parts acceptable for minimum pressure. Never use pressurized air
accessories or parts in the air system that are not
suitable for the maximum air pressure involved. The risk of bursting exists with use of unsuitable equipment. Always maintain maximum pressure specified by the manufacturer is well above the working pressure of your compressor.
14.If your compressor is used for spraying, do not spray in vicinity of open flame or other sources of ignition. Always direct paint or sprayed material away from
compressor and locate compressor to minimize over spray accumulation on compressor or sprayer parts.
15. Do not wipe plastic parts with solvent. Solvents such as gasoline, thinner, benzine, carbon tetrachloride and alcohol may damage and crack plastic parts. Wipe
plastic parts with a soft cloth, lightly dampened with soapy water and dry thoroughly. When using cleaning solvent, follow the instructions provided by the solvent manufacturer.
16.Keep pressure relief devices free from paint or other accumulation. The motor air vent must be kept clean so that air can freely flow at all times. Check for dust build-
up frequently.
17. Do not install Shutoff valves in the discharge line between the compressor and the receiver unless a safety valve, with adequate flow capacity and pressure setting, is located between shutoff valve and the
compressor. Never operate a compressor without all guards or safety features in place and in proper working order.
18.Proper maintenance and care is necessary to ensure safe operation of air compressor. Check compressor according to the maintenance schedule provided in this manual. Maintain compressor with care. Follow
instructions for lubrication. Keep all screws, bolts, and plates tightly mounted. Check for damaged parts and air leaks, daily. Check for alignment of moving parts, binding of moving parts, guard, breakage of parts, and any other conditions that may affect the operation of compressor. Drain tank daily to prevent rust formation and damage.
19.Do not operate any compressor with damaged wiring or hosing, or after the compressor or air handling parts have been dropped, damaged or show signs of
deterioration, weakness or leakage. Do not use them if a deficiency is found. A unit that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this Instruction Manual.
20.Keep clear of compressor while operating It may become extremely hot during operation. To reduce the risk of burns, do not touch tubes, heads, cylinders or motors.
SAFETY INSTRUCTIONS (cont.)
21. Never touch moving parts. Always wear safety goggles or equivalent eye protection. Dress properly. Do not wear loose clothing or jewelry. These can be caught in moving parts. Wear protective hair covering to contain long hair.
22.Never aim compressed air at anyone or any part of the body.
23.Never operate a compressor in damp or wet location. Protect yourself against electric shock. Prevent body contact with grounded surfaces such as pipes, radiators, ranges and refrigeration enclosures.
­
INSTALLATION
UNPACKING INSTRUCTIONS
The two-stage compressor was inspected at the factory and
packaged to protect against shipping damage. When you unpack
your unit, inspect for damaged or missing parts. If there are
any damaged or missing parts, the transportation company’s
agent should make a notation to the effect on the Bill of Lading.
Claims, should be settled directly with the transportation
company.
INSTALLATION
The compressor must be placed in a clean and well-ventilated
room. Compressor should be located at least 12 to 18 inches
away from a wall or other obstruction so that the flow of air
through the flywheel will not be impeded. Rotation of the
flywheel must be in the direction of the arrow cast into the
flywheel.
Gas Compressors
Remove the shipping skid and place unit on a flat , level surface.
For truck mounting always use the same kind of rubber mounts
between frame and tank legs (4). This will allow truck frame or
bed to flex without damaging tank legs and also reduces engine
vibration transferring to truck. From battery to engine starter
use at least 4 AWG cable.
OPERATION
ROTATION OF FLYWHEEL
As the compressor starts, check the rotation of the flywheel.
Standard rotation is clockwise, viewing the compressor from
the side of the sight glass. A rotation arrow, is placed on the flywheel at the factory. Should the rotation be incorrect, disengage
the power and correct the motor wiring.
Electric Compressors
WARNING: After the compressor is started it will operate
automatically with the electric start-stop (pressure switch
control).
When the air pressure in the receiver reaches the preset high
pressure level the pressure switch opens, electrically stopping
the compressor driver motor. As the air is used from the receiver
the pressure drops closing the pressure switch at the preset low
pressure level, restarting the driver motor.
Gas Compressors
Gas Compressor will automatically idle down when it reaches a
maximum pressure and rethrottle at minimum pressure.
AIR INLET FILTER/SILENCER
Stationary Air Compressor Mounting Kit available,
Order 824678
It is very important that the air inlet filter/silencer be kept clean
at all times. A dirty inlet filter reduces the capacity of the compressor. Carefully clean the filter element by blowing the element clean with compressed air from the inside out.
The compressor should be as near as possible to air outlets to
avoid long pipe lines. Do not place compressor where heat is
excessive. Provide adequate fresh air to and exhaust ventilation
from area in which the compressor is located.
CAUTION! Cleaning process should be performed after every
300 hours of operation or more frequently if the compressor
is used in a dusty environment. Install a new air filter element
every two oil changes.
Electric Compressors
Remove wood shipping skid before installation.
Place compressor on a firm, level floor. Permanent installations
should be bolted to the floor. Bolting holes are provided in the
base feet. Shim compressor level before bolting down to floor.
Avoid putting stress on a foot by pulling it down to floor. This
may cause abnormal vibration.
3
LUBRICATION OF COMPRESSOR
Some compressors maybe shipped without oil. Fill crankcase
with oil to level on sight gauge before operating. DO NOT OVERFILL.
Use a high quality, non-detergent petroleum-based compressor oil
TABLE I: Service Conditions
Severity of Service
Maximum Ambient
Temperature (ºF)
Atmospheric
Contamination
Standard
104
Clean, Little
Severe
122
containing anti-oxidant and corrosion-inhibiting additives.
DO NOT USE DETERGENT OILS IN THE PUMP.
For normal ambient termperatures between 41˚F and 77˚F use oil
that meets ISO 100 viscosity requirements (high viscosity SAE 30W
Corrosion
Moderate Dirt,
Corrosion
to low viscosity SAE40W). For ambient temperatures below 41˚F
use oil that meets ISO 68 viscosity requirements (high viscosity SAE
Extreme
20W). For ambient temperatures above 77˚F use oil that meets ISO
150 viscosity requirements (high viscosity SAE 40W).
>122 Class
Severe Dirt,
H Insulation
Abrasive Dust,
Corrosion
Change oil after first 50 hours of use. Afterwards, change
petroleum-based oils and filter every 100 hours of operation.
Low Temperature
-22
TABLE II: Lubrication Interval Multiplier
Operating Condition
Multiplier
Standard
1.00
Severe
0.50
Extreme
0.10
Mounting for Stationary Air Compressor only.
Air Compressor Mounting Kit available, Order 824678.
All Vertical Compressors are top heavy and can easily tip over. Use appropriate lifting device for moving unit to desired location. When using air compressors and compressed air accessories, basic safety rules and precautions should always be followed. Read the compressor operating instruction before
attempting to assemble, install, operate, or maintain the product. Failure to comply with the safety instructions could result in personal injury and/or
property damage.
Disconnect power and release all air pressure before installing and/or performing any maintenance.
The compressor must be placed in a clean and well ventilated room. Compressor should be located at
least 12-18 inches away from a wall or other obstruction that will impede air flow through the fan-bladed
flywheel. Do not place compressor where heat is excessive. Provide adequate fresh air and exhaust ventilation from area in which the compressor is located.
1. Install ¾” NPT nipple into tank outlet hole
2. Install ¾” NPT Ball Valve.
3. Install ¾” x 36” Flexible Hose.
B
Note:
Teflon Tape should be used on all
thread connections.
C
Lag Screw
A
D
36" Flex Hose
A. Nipple
Warning: May bend & curve; do not kink.
B. Outlet Hole
C. Ball Valve
D. Flex Hose
Bushing
Tank Drain
Compressor Foot
Rubber Pad
Lag Shield
4
Concrete Floor
1. Select a location for mounting unit on a firm and level floor.
2. Position unit and mark feet location in center hole of each foot.
3. Prepare to drill holes by removing unit.
4. Drill each of the marked holes 3” in depth using a ¾” concrete drill bit. Blow out holes and insert lag shield making sure they are flush with the floor.
5. Position unit over drilled holes.
Correct
Wrong
6. Place one rubber isolation pad under each
foot.
7. Assemble 1 ½” metal/rubber washer and
lag bolt into each lag shield. Do not over tighten.
WIRING DIAGRAM SA2560V, SA2580V, & SA27580V
Installation Should Be Made By A Competent Electrician
Various national, local codes and standards have been assembled covering electrical apparatus and wiring. These should be consulted
and local ordinances observed. All wiring should be done by a competent electrician.
SA2560V/SA2580V
Pressure
Switch
M
L
L1
BREAKER SIZE (amps)
M
Single Phase
Single-Phase
Motor
L
HP
208V
230V
5
30
30
7 ½
50
50
L2
L1 & L2 indicate supply line terminals.
SA27580V Magnetic Starter 8215PW
MOTOR
INCOMING POWER
LINE
SINGLE PHASE
L1
L2
L3
T1
T2
T3
JUMPER
Pressure
Switch
MOTOR
5
MAINTENANCE
DAILY
•
•
•
Check compressor visually.
Drain moisture from system piping.
Turn power off and drain moisture from tank by opening
drain cock in bottom of tank.
WEEKLY
•
•
•
Check V-belts for tightness. Belt tension should be
adjusted to allow approximately ¼ - ½ inch deflection
with normal thumb pressure.
Check oil level and add oil as required.
Turn power off and clean dust and foreign material from
cylinder head, motor, flywheel blades, air lines, inter
cooler, aftercooler and tank.
MONTHLY
•
Turn power off, reduce receiver pressure to 25 PSI and
check operation of high pressure safety valve by pulling
ring.
Check flywheel and motor pulley bolts for tightness.
•
QUARTERLY
•
Every 90 days check entire system for air leakage around
fittings, etc. using a soap solution. Tighten nuts and cap
screws as required.
EVERY TWO YEARS
•
Clean the delivery and suction valves.
MAINTENANCE SCHEDULE - CHECK CHART
PROCEDURE
DAILY
Check Oil Level. Caution! Do
not overfill.
X
Perform visual check of compressor.
X
Drain moisture accumulation from
the air receiver and system piping.
X
WEEKLY
MONTHLY
QUARTERLY YEARLY
X
Check the air distribution system
for air leaks
Clean dust from all cooling surfaces
of compressor.
X
X
Operate safety valves (pressure
relief valve).
X
Check belts for correct tension and
alignment.
X
Check motor pulley and flywheel bolts
for tightness.
Inspect discharge line for excessive
carbon accumulations.
X
Inspect pressure switch diaphragm and
contact points for deterioration.
X
X
Inspect valve assemblies.
Change compressor oil.
‡
‡
‡
‡
‡
Replace or clean intake filter element.
‡
‡
‡
‡
‡
Service electric motor.
‡
‡
‡
‡
‡
X = Check more often if extremely dirty condition exists
‡ = Per manufacturer’s recommendations
6
TROUBLESHOOTING
PROBLEM
1.
Compressor will not operate.
2. Excessive noise in operation
POSSIBLE CAUSE
CORRECTIVE ACTION
1. No electrical power.
2. Pressure switch not making contact
1. Turn on power.
2. See pressure switch adjustment.
1. Loose pulley, flywheel, belt, beltguard,
cooler, clamps or accessories.
2. Lack of oil in crankcase.
1. Tighten.
4. Compressor floor mounting loose.
5. Defective crankcase.
6. Excessive crankshaft end play.
2. Check for possible damage to
bearings, replenish oil.
3. Remove the compressor cylinder
head and inspect for foreign
matter on top of the piston.
Add a new gasket and reassemble
the head.
4. Tighten.
5. Repair or replace.
6. Adjust and shim properly.
3. Knock - same cycle as R.P.M.
1. Main bearings.
1. Replace bearings.
4. Knock occurs while
compressor is loading.
1. Connecting rod bearings.
1. Replace rod bearing and examine
crankshaft.
2. Replace complete piston
assembly.
5. Milky oil in oil reservoir.
1. Water entering oil reservoir due
to compressor operating in high
humidity environment.
1. Pipe air intake to less humid air
source.
6. Excessive oil consumption.
1.
2.
3.
4.
1.
2.
3.
4.
3. Piston hitting the valve plate.
2. Wrist pins, wrist pin bearings.
Restricted air intake.
Oil leaks.
Worn piston rings.
Wrong oil viscosity.
5. Compressor titled excessively.
6. Scored cylinder.
7.
Oil in discharge air.
1. Compressor air intake restricted.
2. Worn piston rings.
3. Excessive oil in compressor.
4. Wrong oil viscosity.
5. Piston rings installed up-side down.
8. Compressor vibrates.
1. Mounting bolts loose.
2. Compressor not properly mounted.
3. Pulley and flywheel misaligned.
4. Belts loose.
5. Bent crankshaft.
Clean or replace air filter.
Tighten bolts or replace gasket.
Replace piston rings.
Drain oil, refill with oil of proper
viscosity. See Lubrication Section.
5. Level compressor.
6. Replace cylinder.
1. Clean air filter element and check
for other restrictions in the intake
system.
2. Replace rings.
3. Drain down to full mark on sight
gauge.
4. Drain oil, refill with oil of proper
viscosity. See Lubrication Section.
5. Install ring in proper position.
1. Tighten.
2. Level compressor so that all feet
touch the floor before tightening
down.
3. Realign.
4. Tighten belts. See Maintenance
Section.
5. Replace crankshaft.
7
TROUBLESHOOTING (continued)
PROBLEM
POSSIBLE CAUSE
CORRECTIVE ACTION
9. Air blowing out of inlet
1. Broken first stage inlet valve.
1. Replace valve assembly.
10. Insufficient pressure at point
of use.
1. Leaks or restrictions.
1. Check for leaks or restrictionsr
in piping. Repair.
2. Clean or replace air filter
element.
3. Tighten belts. See Maintenance
Section.
4. Replace with larger hose.
5. Limit air requirement to
compressor capacity.
2. Restricted air intake.
3. Slipping belts.
4. Service hose too small.
5. Excessive air requirement.
11. Receiver does not hold pressure
when compressor is unloaded.
1. Faulty check valve.
1. Bleed Tank! Disassemble check
valve assembly, clean or
replace faulty parts. DANGER:
Do not disassemble check valve with air in tank. NOTE: Check valve is always the first valve in the line leading from the tank to the compressor.
12. Excessive belt wear.
1. Pulley out of alignment.
1. Realign motor pulley with
compressor flywheel.
2. Adjust tension. See Maintenance
Section.
3. Adjust tension. See Maintenance
Section.
4. Check for worn crankshaft,
keyway or pulley bore, resulting
from running with loose pulleys.
Check for bent crankshaft.
5. File smooth.
2. Belts too tight.
3. Belts too loose.
4. Pulley or flywheel wobble.
5. Nick in belt grove of pulley or
flywheel.
13. Excessively hot discharge air
1. Dirty cooling surfaces.
2. Poor ventilation.
3. Blown head gasket.
4. Restricted air intake
5. Worn valves.
14. Receiver pressure builds
up slowly.
1. Dirty air filter.
2. Blown cylinder head gasket.
3. Worn or broken low pressure
intake or discharge valves.
4. Air leaks.
5. Loose belts.
6. Speed too slow.
8
1. Clean all surfaces of foreign
material.
2. Improve ventilation or relocate
compressor. See Installation.
3. Replace head gasket.
4. Clean or replace air filter element.
5. Repair or replace valves.
1. Clean or replace filter element.
2. Install new head gasket.
3. Install new valve assembly.
4. Tighten joints.
5. Tighten belts. See Maintenance
Section.
6. Check electric motor performance.
Load Genie Instructions
Installation
The Load Genie has 1/2 NPT “IN” and “OUT” ports and is suitable for compressor with discharge capacities of up to 32
SCFM . The Load Genie is typically installed onto the tank
with a short pipe nipple. The “OUT” port must be connected
directly to the tank with no other check valves in between
the tank and the Load Genie. (NOTE: On some retrofit applications, there may have been a type of check valve known
as an “In Tank” check valve previously installed. Make sure
there is a clear air path between the tanks and “OUT” port
before installing the Load Genie. The compressor discharge
line can now be routed into the “IN” port of the Load Genie.
The installation is now complete.
Inlet (Connected to Compressor)
Easy Start Lever
Range Adjustment Screw
Range Jam Nut
Differential Adjustment Screw
Differential Jam Nut
VENT
Vent Port
(See rear, open to
Atmosphere)
Regulator Adjustment
Cutout pressure is adjustable from 60 PSI to 175 PSI with
the standard silver spring. The differential (difference
between cut-out and cut-in pressures) is typically set at the
factory at approximatly 15% of the cut-out pressure. This is
usually a suitable differential and will not normally need to
be readjusted.
1. Loosen range screw jam nut first.
2. Turn range screw clockwise to raise cut-out and cut-in pressure levels and counter clockwise to decrease cut-
out and cut-in levels.
3. Start compressor and note cut-out and cut-in presures. Make adjustments as necessary using range
adjustment screw; when acceptable, tighten range adjustment screw jam nut.
4. Adjust the cut-in pressure to the desired level per steps #1, #2, and #3, as shown above.
5. Loosen differential screw jam nut and turn differential screw clockwise to raise cut-out pressure and counter clockwise to decrease the the cut-out
pressure.Tighten differential screw jam nut when desired cut-out pressure is set. Since step #5 should not change the desired cut-in pressure set in step #4,
adjustment is now complete.
1/8 NPT
Throttle Control Port
Out (Connected to Tank)
Starting Unit
Loadgenie3 112807.ai
Easy Start: Place Easy Start Lever in upright position. Start unit.
When running smoothly, flip lever to run position.
Start Position
Run Position
Use with Gasoline Engine
Throttle Controls
A 1/8 NPT tapped port in the end of the Load Genie allows
the use of a throttle control to slow down the driving engine
when in the cutout (venting) mode. The throttle control is
simply a small (e.g., 1/2” dia. X 1” stroke) single-acting, spring
return air cylinder which moves the throttle lever on the
engine to the idle position when the cylinder is pressurized
while in the cut-out mode. 709 Throttle control is specifically designed for this application. It is improtant that the
throttle control air cylinder is leak-tight and that all connections between that Load Genie and the air cylinder are
leak-tight.
9
COMPRESSOR SPECIFICATIONS
GENERAL SPECIFICATIONS
SA2560V
SA2580V
SA27580V
Height (in.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Width (in.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 3/8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 ½ . . . . . . . . . . . . . . . . . . . . . . . . . . 36 ½
Depth (in.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Motor Output (HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.5
Net Weight (lb.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 340 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 435 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 515
Tank Size (Gal.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
PUMP SPECIFICATIONS
Air Output (CFM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.5 CFM @ 175 PSI . . . . . . . . . . . . . 13.5 CFM @ 175 PSI . . . . . . . . . . 17.0 CFM @ 175 PSI
14.0 CFM @ 100 PSI . . . . . . . . . . . . 14.0 CFM @ 100 PSI . . . . . . . . . . 17.5 CFM @ 100 PSI
Number of Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Low-Pressure Bore Diameter (in.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.74 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.74 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1
Hi-Pressure Bore Diameter (in.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.05 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.05 . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.04
Piston Stroke (in.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.36 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.36 . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.95
Displacement (in.3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25.9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25.9 . . . . . . . . . . . . . . . . . . . . . . . . . . . 39.6
Air Input (CFM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.5 . . . . . . . . . . . . . . . . . . . . . . . . . . . 24.5
Speed @ 100 PSIG (RPM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1301 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1301 . . . . . . . . . . . . . . . . . . . . . . . . . . . 1065
Working Pressure (PSIG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
Flywheel Pitch Diameter (in.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.53 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.53 . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.53
Oil Capacity (qt.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.7
Length (in.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.7
Width (in.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.4
Height (in.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.9 . . . . . . . . . . . . . . . . . . . . . . . . . . . 20.5
GENERAL SPECIFICATIONS
SA788B (E) (H)
SA6830B (H)
SA61030B - SA61130H
Height (in.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29.5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Width (in.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Depth (in.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Motor Output (HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Net Weight (lb.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300
Tank Size (Gal.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Twin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
PUMP SPECIFICATIONS
Air Output (CFM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.5 CFM ­­@ 175 PSI . . . . . . . . . . . . . 13.5 CFM ­­@ 175 PSI . . . . . . . . . . 17.0 CFM ­­@ 175 PSI
14.0 CFM @ 100 PSI . . . . . . . . . . . . . 14.0 CFM @ 100 PSI......................17.5 CFM @ 100 PSI
Number of Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Low-Pressure Bore Diameter (in.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.74 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.74 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1
Hi-Pressure Bore Diameter (in.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.05 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.05 . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.04
Piston Stroke (in.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.36 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.36 . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.95
Displacement (in.3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25.9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25.9 . . . . . . . . . . . . . . . . . . . . . . . . . . . 39.6
Air Input (CFM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.5 . . . . . . . . . . . . . . . . . . . . . . . . . . . 24.5
Speed @ 100 PSIG (RPM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1301 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1301 . . . . . . . . . . . . . . . . . . . . . . . . . . . 1065
Working Pressure (PSIG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
Flywheel Pitch Diameter (in.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.53 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.53 . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.53
Oil Capacity (qt.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.7
Length (in.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.7
Width (in.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.4
Height (in.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.9 . . . . . . . . . . . . . . . . . . . . . . . . . . . 20.5
10
AIR CONSUMPTION CHART
SCFM
PSI
Air filer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.0*
Air filter cleaner. . . . . . . . . . . . . . . . . . . . . 70-100 . . . . . . . . . . . . . . 3.6*
Air motors
PSI
SCFM
Spray gun
Production . . . . . . . . . . . . . . . . . . . . . . . 90-100 . . . . . . . . . . . . . . . . 16.0*
Touchup . . . . . . . . . . . . . . . . . . . . . . . . . . 90-100 . . . . . . . . . . . . . . . . 8.0*
Undercoating . . . . . . . . . . . . . . . . . . . . 90-100 . . . . . . . . . . . . . . . . 19.0*
1 HP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.0
2 HP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.0
3 HP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.0
Tire bead breaker . . . . . . . . . . . . . . . . . 125-150 . . . . . . . . . . . . . . . . 12.0*
Air polisher. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.0
Tire hammer . . . . . . . . . . . . . . . . . . . . . . . 90-100 . . . . . . . . . . . . . . . . . 12.0
Blow gun. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90-100. . . . . . . . . . . . . . . . 2.4
Tire inflation line . . . . . . . . . . . . . . . . . 125-150 . . . . . . . . . . . . . . . . . 1.4
Brake tester. . . . . . . . . . . . . . . . . . . . . . . . . . 70-100. . . . . . . . . . . . . . . . . 3.6
Tire spreader . . . . . . . . . . . . . . . . . . . . . . 125-150 . . . . . . . . . . . . . . . . . 1.0
Caulking gun. . . . . . . . . . . . . . . . . . . . . . . . . . . 10-70. . . . . . . . . . . . . . . . . 2.2
Transmission flusher . . . . . . . . . . . . . 70-100 . . . . . . . . . . . . . . . . . 3.0
Circular saw. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.0
Carbon remover . . . . . . . . . . . . . . . . . . . .70-100 . . . . . . . . . . . . . . . . 3.0*
Die grinder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.0
Burring tool . . . . . . . . . . . . . . . . . . . . . . . . 90-100 . . . . . . . . . . . . . . . . 5.0*
Drill, 3/8 inch. . . . . . . . . . . . . . . . . . . . . . . . . 70-90. . . . . . . . . . . . . . . . 4.0*
Vacuum cleaner . . . . . . . . . . . . . . . . . . . 125-150 . . . . . . . . . . . . . . . . . 6.0
Engine cleaner. . . . . . . . . . . . . . . . . . . . . . . 90-100. . . . . . . . . . . . . . . . 5.0
Hydraulic floor jack . . . . . . . . . . . . . . 125-150 . . . . . . . . . . . . . . . . . 6.0
Fender hammer. . . . . . . . . . . . . . . . . . . . . . 70-100. . . . . . . . . . . . . . . 9.0*
Radiator tester . . . . . . . . . . . . . . . . . . . . 90-100 . . . . . . . . . . . . . . . . . . 1.1
Filing machine. . . . . . . . . . . . . . . . . . . . . . . 90-100. . . . . . . . . . . . . . . 5.0*
Air saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.0
Grease gun. . . . . . . . . . . . . . . . . . . . . . . . . . 120-150. . . . . . . . . . . . . . . 6.0*
Vertical air sanders
5” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.0
7” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.0
9” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.0
Hydraulic lift. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.0-12.0*
Impact wrench
3/8 inch . . . . . . . . . . . . . . . . . . . . 70-90. . . . . . . . . . . . . . . . 3.0*
½ inch . . . . . . . . . . . . . . . . . . . . 70-90. . . . . . . . . . . . . . . . 4.0*
5/8 inch . . . . . . . . . . . . . . . . . . . . 70-90. . . . . . . . . . . . . . . . 5.0*
¾ inch . . . . . . . . . . . . . . . . . . . . 70-90. . . . . . . . . . . . . . . . 8.0*
1 inch . . . . . . . . . . . . . . . . . . . . 70-90. . . . . . . . . . . . . . . 12.0*
Air hammer. . . . . . . . . . . . . . . . . . . . . . . . . . . 90-100. . . . . . . . . . . . . . . 7.0*
Orbital sander . . . . . . . . . . . . . . . . . . . . . . . 70-100. . . . . . . . . . . . . . . 12.0*
Tire changer . . . . . . . . . . . . . . . . . . . . . . . 125-150 . . . . . . . . . . . . . . . . 1.0
Vertical grinder
3” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.0
4” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.0
7” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24.0
Consult the spec. sheet supplied with your air tool or
equipment for the exact operating pressure and air volume requirements.
*Continuous Run Tools
Panel cutter. . . . . . . . . . . . . . . . . . . . . . . . . . 70-100. . . . . . . . . . . . . . . . 4.0
Nail hammer . . . . . . . . . . . . . . . . . . . . . . . . . 90-100. . . . . . . . . . . . . . . . 4.0
Rim stripper. . . . . . . . . . . . . . . . . . . . . . . . . 125-150. . . . . . . . . . . . . . . . 5.0
Spark plug cleaner . . . . . . . . . . . . . . . . . . 90-100. . . . . . . . . . . . . . . . 5.0
Air scaler. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.0
11
82289015 COMPRESSOR PUMP
For Compressors:
SA256V
SA258V
SA788B, SA788BE, SA788H
SA6830B, SA68030H
36
35
19
17
21
27
28
33
34
29
18
20
37
44
16
15
43
32
5
31
38
43
39
26
46
25
42
30
11 12 13 14
6
9
8
4
24
3
47
40
23
10
22
Head Bolt Torque: 33.2 ft-lbs
12
7
2
1
41
45
82-289015 / BK119
82-289015 / BK119
#
Part Number
Description
#
Part Number
Description
1
82-286932
Lower Cover
24
82-213141020
part of full gasket set - #45
2
82-213141020
part of full gasket set - #45
25
82-287077
Valve Holder Plate
3
82-286930
Vibration Damper
26
82-213141020
part of full gasket set - #45
4
82-286929
Casing
27
82-213141020
part of full gasket set - #45
5
82-213141020
part of full gasket set - #45
28
*GH
Screw
6
82-286945
Bearing
29
*GH
Screw
7
82-010008000
Seal
30
*GH
Screw
8
82-286947
Front Cover
31
82-047002000
Safety Valve (16,5 Bar)
9
82-013178007
B-Groove Flywheel
32
82-113163025
Final Manifold
10
82-286935
Oil Level Sight Glass
33
82-113179013
Head 1” NPT
11
82-286937
Rear Cover
34
82-047086000
Safety Valve (6 Bar)
12
82-286939
Oil Plug
35
82-113178004
Conveyor
13
82-213141020
part of full gasket set - #45
36
82-113178011
Eyebolt
14
82-286957
Bearing
37
82-013141039
Manifold
15
82-113178006
Crankshaft
38
82-213141020
part of full gasket set - #45
16
*GH
Feather
39
82-113141040
Manifold Cover
17
82-286956
Connecting Rod
40
*GH
Plug
18
82-213129002
Piston Ring Kit HP
41
*GH
Screw
19
82-286894
Complete Piston HP
43
*GH
Screw
20
82-286973
Piston Ring Kit LP
44
82-014005001
Washer
21
82-287071
Complete Piston LP
45
82-213141020
Full Gasket Set
22
82-213141020
part of full gasket set - #45
46
82-289017
Air Filter Assembly
23
82-113179001
Cylinder
47
82-288665
Air Filter Element
* General Hardware Part can be found at your local Auto
Parts/Hardware Store.
13
82-289016 COMPRESSOR PUMP
For Compressors:
SA27580V
SA61030B, SA61130H
38
19
21
37
20
30
31
35
39
34
18
45
23
5
33
29
46 45
16
15
36
32
17
18
22
40
28
48
41
44
11 12 13 14
6
27
9
8
4
26
3
49
42
25
10
24
Head Bolt Torque: 33.2 ft-lbs
14
7
2
1
43
47
82-289016 / BK119
82-289016 / BK119
#
Part Number
Description
#
Part Number
Description
1
82-286932
Lower Cover
26
82-213153020
part of full gasket set - #47
2
82-213153020
part of full gasket set - #47
27
82-287077
Valve Holder Plate
3
82-286930
Vibration Damper
28
82-213153020
part of full gasket set - #47
4
82-286860
Casing
29
82-213153020
part of full gasket set - #47
5
82-287095
part of full gasket set - #47
30
82-213153020
part of full gasket set - #47
6
82-286945
Bearing
31
*GH
Screw
7
82-010008000
Seal
32
*GH
Screw
8
82-286947
Front Cover
33
82-047002000
Safety Valve (16,5 Bar)
9
82-013178007
B-Groove Flywheel
34
82-113163025
Final Manifold
10
82-286935
Oil Level Sight Glass
35
82-113179013
Head 1” NPT
11
82-286937
Rear Cover
36
82-047086000
Safety Valve (6 Bar)
12
82-286939
Oil Plug
37
82-113178004
Conveyor
13
82-213153020
part of full gasket set - #47
38
82-113178011
Eyebolt
14
82-286957
Bearing
39
82-013141039
Manifold
15
82-286880
Crankshaft
40
82-113141040
Manifold Cover
16
*GH
Feather
41
*GH
Screw
17
82-286915
Connecting Rod HP
42
*GH
Plug
18
NA separate w/rod
Connecting Rod Bearing
43
*GH
Screw
19
82-286963
Piston Ring Kit 052 HP
44
*GH
Screw
20
82-413141029
Complete Piston HP
45
*GH
Screw
21
82-286901
Piston Ring Kit 095 HP
46
*GH
Washer
22
82-286904
Complete Piston LP
47
82-213153020
Full Gasket Set
23
82-286884
Connection Rod LP
48
82-289017
Air Filter Assembly
24
82-213153020
part of full gasket set - #47
49
82-288665
Air Filter Element
25
82-286908
Cylinder
* General Hardware Part can be found at your local Auto
Parts/Hardware Store.
15
AIR COMPRESSOR
SA2560V
SA2580V
SA27580V
1
3
2
17
16
19
15
4
5
6
14
13
8
7
9
18
Diagram
No.
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
16
Belt Guard
Belt
Support Bracket
Pump
Extension
Cap
Fitting
Check Valve
Tube
Gauge
Pressure Switch
Safety Valve
Fitting
Fitting
Tube
Fitting
Motor
Tank
Pulley
11
12
10
SA2560V
82-9004
82-9003
82-288602
82-289015
287104
287102
82-630
82-P7575
82-600-2560V
283495
82-779
283805
82-997
82-9011
82-604-356-VAT
82-9010
82-5000MD
82-9901R
82-9002
SA2580V
82-9004
82-9003
82-288602
82-289015
82-9031
287102
82-630
82-P7510
82-600-2580V
283495
82-779
283805
82-9022
82-9011
82-604-358-VAT
82-9010
82-5000MD
82-81R
82-9002
SA27580V
82-9004
82-9018
82-288602
82-289016
82-9031
287102
82-630
82-P7510
82-600-27580V
283495
82-779
283805
82-9022
82-9021
82-603-368-VAT
82-9020
82-6200MA
82-81R
82-9017
AIR COMPRESSOR
SA788B, SA788BE,
SA788H
Back Side of Gas Engine
18
17
19
3
2
1
4
INTEK I
5
IN
VENT
VENT
8
6
OUT
7
9
10
16
11
15
14
13
Diagram
No.
Part No.
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
82-288623
82-288618
82-289015
82-288624
82-205BN
82-604-788
82-625
82-709
283805
283495
82-651
82-29
82-650
82-288626
82-685
81287561
82-3804HI
82-288613
82-747
8.0 HP Briggs & Stratton Gas Engine
Belt Guard
Pump (See pages 11-12)
Fitting
Throttle Cable
Discharge Tube
90˚ Fitting
Load Genie (See page 8)
Safety Valve
Pressure Gauge
4 way cross
Handle grips
Drain
Tank
Rubber Feet
Wheel
Bushing
Belt
Sheave
12
17
AIR COMPRESSOR
SA6830B, SA6830H,
SA610030B, SA61130H
13
Back Side of
Gas Engine
14
15
16
1
2
3
4
INTEK I
IN
VENT
VENT
5
6
OUT
12
7
8
11
9
10
Diagram
No.
1
2
3
4
5
6
7
8
9
10
11
12
12
13
14
15
16
18
SA6830B, SA6830H
Part No.
82-288618
82-288614
82-604-6830
82-205BN
82-625
82-709
82-288610R
283805
82-652
82-650
283495
(8 HP) 82-288611
(GX240) 82-841E
82-3804HI
82-288613
82-747
82-289015
SA61030B, SA61130H
Part No.
Description
82-288618
82-288614
82-604-61130
82-205BN
82-625
82-709
82-288610R
283805
82-652
82-650
283495
(10 HP) 82-288619
(GX340) 82-842E
82-3804HI
82-288613
82-288620
82-289016
Belt Guard
Fitting
Discharge Tube
Throttle Control
90˚ Fitting
Load Genie (See page 8)
Tank
Safety Valve
1/4” Tee
Drain Cock
Pressure Gauge
Briggs & Stratton Gas Engine
Honda Gas Engine
Bushing
Belt
Sheave
Pump
(See pages 12-15)
Schrader International Inc.
Warranty Statement
For (1) one year from the date of purchase, Schrader International Inc. will replace or repair for the original purchaser
free of charge, any part or parts found upon examination
by manufacturer/any Authorized Service Center to be
defective in material or workmanship
or both. This warranty shall not be effective unless the
warranty registration certificate is completely filled out
and returned to Schrader International Inc. within thirty
(30) days from the delivery of the equipment to the original
end-user.
All transportation charges for parts submitted for replacement under this warranty must be borne by the purchaser.
There is no other express warranty. Implied warranties,
including those of merchantability and fitness for a
particular purpose are limited to one year from the date
of purchase and to the extent permitted by law, any and
all implied warranties are excluded. This is the exclusive
remedy, and liability for consequential damages under any
and all warranties are excluded to the extent exclusion is
permitted by law.
All claims pertaining to the merchandise in this schedule
must be filed with Schrader International Inc. within 12
months of the invoice date, and a registration card is on
file with Schrader, or they will not be honored. Prices,
discount, and terms are subject to change without notice
or as stipulated in specific product quotations. All agreements are contingent upon strikes, accidents, and other
causes beyond our control. All shipments are carefully
inspected and counted before leaving the factory. Please
inspect carefully any receipt of merchandise, noting any
discrepancy or damage on the carrier’s freight bill at time
of delivery. Discrepancies or damage, including hidden or
obvious that occurred in transit are the carrier’s responsibility and related claims should be made by the customer
directly with the carrier.
To locate the closest Authorized Service Center for service
assistance, resolution of a service problem or for product
information and operation, call or write to:
Schrader International Inc.
205 Frazier Road
Altavista, VA 24517
Email: TechSvc@SchraderIntl.com
1.800.288.1804
Tech Service, ext. 1577
What is not covered under this warranty:
• Electric motors or gasoline engines are covered by the
Original Manufacturer’s Warranty and should be returned
(by the customer) to their authorized service center for
service.
• Consumer compressors used in commercial, industrial or
rental purposes will be covered by warranty for (90)
ninety days from date of purchase only.
• Any failure that results from an accident, purchaser’s
abuse, neglect or failure to operate products in
accordance with instructions provided in the owner’s
manual(s) supplied with compressor.
• Pump or valve failure caused by rain, excessive humidity,
corrosive environments or other contaminants.
• Cosmetic defects that do not interfere with the
compressor’s functionality.
• Damage due to incorrect voltage or improper wiring.
• Pump wear or valve damage caused by any oil
contamination or by failure to follow proper oil
maintenance guidelines.
• This warranty is invalid if the factory-applied serial
number has been altered or removed from the product,
or an electric compressor has been used in conjunction
with a generator.
• Freight damage
19
S C H RA D ER – USA
2 0 5 F R AZI ER ROAD • A LTAV I STA , VA 2 4 5 1 7
CUSTOMER SUP P O RT LINE // 1.8 00.28 8 .18 04
S C H RAD E RI N TE RN ATI O N AL . C O M
performance manual SA - 011113
Download PDF
Similar pages