RS2315K - Supercheap Auto

Cordless Drill
EN
RS2315K
RS2315K
1
2
8
3
7
4
5
6
A
a
c
b
B
C
A
D1
F
G
a
c
5
RS2315K
6
b
B
C
D2
E
Cordless Drill
EN
COMPONENT LIST
.
1
Keyless chuck
2
Variable clutch
3
Forward and reverse rotation selector
4
Soft grip handle
5
Battery
pack latch
6
Battery
pack
7
On/Off
switch with variable speed control
8
Sight light
Not all the accessories illustrated or described are included in standard delivery.
ACCESSORIES
1500mAh Ni-Cd battery pack
double ended bits
1h charger
1
1
1
Use good quality accessories marked with a
well-known brand name. Choose the type according
to the work you intend to undertake. Refer to the
accessory packaging for further details. Store
personnel can assist you and offer advice.
General Power Tool Safety
Warnings
WARNING: Read all safety warnings and all
instructions. Failure to follow the warnings
and instructions may result in electric shock, fire and/
or serious injury.
Save all warnings and instructions for future
reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or batteryoperated (cordless) power tool.
1. Work Area safety
a) Keep your work area clean and well lit. Cluttered
or dark areas invite accidents.
b)Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
c) Keep bystanders, children, and visitors away
while operating a power tool. Distractions can
cause you to lose control.
2.Electrical Safety
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools.Unmodified plugs and matching outlets will
reduce risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges
and refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
5
Cordless Drill
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
3. Personal Safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
b) Use personal protective equipment. Always
wear eye protection. Protective equipment
such as dust mask, non-skid safety shoes, hard
hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energising power
tools that have the switch on invites accidents.
d) Remove adjusting keys or wrench before
turning the tool on. A wrench or a key left
attached to a rotating part of the power tool
may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery
or long hair can be caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
these devices can reduce dust-related hazards.
4. Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
6
EN
controlled with the switch is dangerous and must
be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions
to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tools operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions and
in the manner intended for the particular type
of power tool, taking into account the working
conditions and the work to be performed. Use of
the power tool for operations different from those
intended could result in a hazardous situation.
5. Battery tool use and care
a) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one
type of battery pack may create a risk of fire when
used with another battery pack.
b) Use power tools only with specifically
designated battery packs. Use of any other
battery packs may create a risk of injury and fire.
c)When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal
to another. Shorting the battery terminals
together may cause burns or a fire.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical
help. Liquid ejected from the battery may cause
irritation or burns.
Cordless Drill
6. Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that that safety of the
power tool is maintained.
Drill Safety Warnings
1.Wear ear protectors when impact drilling.
Exposure to noise can cause hearing loss.
2.Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
3.Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting
accessory contacting a “live” wire may make
exposed metal parts of the power tool “live” and
could give the operator an electric shock.
General Safety Warnings for your Battery Charger
WARNING: Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future
reference.
- This appliance is not intended for use by persons
(including children) with reduced physical,
sensory or mental capabilities, or lack of
experience and knowledge, unless they have been
given supervision or instruction concerning use
of the appliance by a person responsible for their
safety.
- Children should be supervised to ensure that they
do not play with the appliance.
Additional safety instructions for your Battery
Charger
1. Before charging, read the instructions.
2. For charge Ni-Cd battery pack only.
3. If the supply cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
4. The battery terminal not connected to the chassis
has to be connected first. The other connection is
to be made to the chassis, remote from the battery
and fuel line. The battery charger is then to be
connected to the supply mains.
5. After charging, disconnect the battery charger
from the supply mains. Then remove the chassis
EN
connection and then the battery connection.
6.Do not charge a leaking battery.
7.Do not use chargers for works other than those for
which they are designed.
8. Before charging, ensure your charger is matching
the local AC supply.
9. The charging device must be protected from
moisture.
10.Do not use the charging device in the open.
11.Do not short out the contacts of battery or
charger.
12.Respect the polarity “+/-“ when charging.
13.Do not open the unit and keep out of the reach of
children.
14.Do not charge the batteries of other manufactures
or ill-suited models.
15.Ensure that the connection between the battery
charger and battery is correctly positioned and is
not obstructed by foreign bodies.
16.Keep battery charger’s slots are free of foreign
objects and protect against dirt and humidity.
Store in a dry and frost-free place.
17. When charging batteries, ensure that the battery
charger is in a well-ventilated area and away from
inflammable materials. Batteries can get hot
during charging. Do not overcharge any batteries.
Ensure that batteries and chargers are not left
unsupervised during charging.
18.Do not recharge non-rechargeable batteries, as
they can overheat and break.
19.Longer life and better performance can be
obtained if the battery pack is charged when the
air temperature is between 18oC and 24oC. Do not
charge the battery pack in air temperatures below
4.5oC, or above 40.5oC. This is important as it can
prevent serious damage to the battery pack.
20.Charge only battery pack of the same model
provided by manufacturer and of models
recommended by manufacturer.
7
Cordless Drill
Symbols
To reduce the risk of injury, user must read in struction manual
Warning
Wear ear protection
Wear eye protection
Wear dust mask
C-Tick approval mark
Do not burn
Do not expose to rain or water
Indoor use only
Positive terminal
Negative terminal
8
EN
Technical data
Charge voltage
Battery voltage
Rated No load speed
Max. torque
Number of clutch position
Chuck capacity
Max. drilling capacity
Steel
Wood
Weight
220-240V-50/60Hz
18V
0-550/min
17N.m
20+1
Ø10mm
10mm
22mm
1.7kg
CHARGING PROCEDURE
NOTE: Before using the tool, read the
instruction book carefully.
1. CHARGING YOUR BATTERY PACK
Warning: The charger and battery pack are
specifically designed to work together so do
not attempt to use any other devices. Never insert or
allow metallic objects into your charger or battery
pack connections because an electrical failure and
hazard will occur.
2. BEFORE USING YOUR CORDLESS DRILL
Your battery pack is UNCHARGED and you must
charge once before use. Your battery pack will not be
fully charged until you have performed several charge
and discharge operations by charging & working with
your drill. After this your battery pack performance
will improve.
2) To charge the battery (See Fig. A)
• Insert the charger plug into a suitable mains
socket. Insert the battery pack (6) into the charger,
the power indicator (green) (a) will illuminate.
• Press the charging start button (c) on the charger
station. The green light (a) will switch off while the
red light (b) will illuminate to indicate that charging
is taking place.
• When fully charged, the red light (b) will go out
while the green light (a) switches back on. Unplug
the charger and remove the battery pack.
WARNING: When battery charge runs out
after continuously use or exposure to direct
sunlight or heat, allow time for the tool to cool down
before re-charging to achieve the full charge.
NOTE: A fully-discharged battery will take
Cordless Drill
approximately 60 minutes to become fully charged.
After 60 minutes, a timer circuit inside the charger will
activate to switch off the charging system. When a
partly discharged battery is charged, it may become
fully charged before the timer circuit is activated. In
this case, a safety cutout inside the battery pack will
terminate the charging process. The safety cutout
will also terminate the charging process if the internal
temperature of the battery pack gets too high.
4. TO REMOVE OR INSTALL BATTERY PACK (See Fig.B)
Locate latches on side of battery pack and depress
both sides to release battery pack from your drill.
After recharge, insert the battery pack into drill’s
battery port. A simple push and slight pressure will
be sufficient.
OPERATING INSTRUCTIONS
Intended Use
The machine is intended for driving in and loosening
screws as well as for drilling in wood, metal and
plastic.
1. ON/OFF SWITCH
Depress to start and release to stop your drill. The on/
off switch is fitted with a brake function which stops
your chuck immediately when you quickly release the
switch.
It is also a variable speed switch that delivers higher
speed and torque with increased trigger pressure.
Speed is controlled by the amount of switch trigger
depression.
Warning: Do not operate for long periods
at low speed because excess heat will be
produced internally.
2. SWITCH LOCK (See Fig. C)
The switch trigger can be locked in the OFF position.
This helps to reduce the possibility of accidental
starting when not in use. To lock the switch trigger,
place the direction of rotation selector in the center
position.
3. REVERSIBLE (See Fig. D1, D2)
For drilling and screw driving use forward rotation
marked “
” (lever is moved to the left). Only
use reverse rotation marked “
” (lever is
moved to the right) to remove screws or release a
EN
jammed drill bit.
Warning: Never change the direction of
rotation when the chuck is rotating. Wait until it
has stopped.
4. CHUCK ADJUSTMENT (See Fig. E)
To open the chuck jaws rotate the front section of
the chuck. Insert the drill bit between the chuck jaws
and rotate the front section in the opposite direction.
Ensure the drill bit is in the center of the chuck jaws.
Finally, firmly rotate the front chuck section in the
opposite directions. Your drill bit is now clamped in
the chuck.
5. TORQUE ADJUSTMENT (See Fig. F)
(Screw driving force of your drill driver)
The torque is adjusted by rotating the torque
adjustment ring. The torque is greater when the
torque adjustment ring is set on a higher setting. The
torque is less when the torque adjustment ring is set
on a lower setting.
Make the setting as follows:
1 - 4 for driving small screws
5 - 9 for driving screws into soft material
10 - 14 for driving screws into soft and hard
material
15 - 19 for driving screws into hard wood
20
for driving larger screws
for heavy drilling
7. DRILLING
When drilling hard smooth surfaces, use a center
punch to mark the desired hole location. This will
prevent the drill bit from slipping off center as the
hole is started. Hold the tool firmly and place the tip
of the bit at the point to be drilled. Depress the switch
trigger to start the tool. Move the drill bit into the
work-piece, applying only enough pressure to keep
the bit drilling. Do not force or apply side pressure to
elongate a hole.
WARNING: Tungsten carbide drill bits should
always be used for concrete and masonry.
When drilling in metal, only use HSS drill bits in
good condition. Always use a magnetic bit holder
when using short screwdriver bits. When
screw-driving, apply a small quantity of liquid soap
or similar to the screw threads to ease insertion.
7. USING THE SIGHT LIGHT
9
Cordless Drill
The sight light allows you to keep a clear view under
less illuminated circumstances. To turn on the light
simply press the on/off switch. When you release the
on/off switch, the light will be off.
PROBLEM SOLUTION
1. WHY DOES THE DRILL NOT TURN ON WHEN YOU PRESS
THE SWITCH?
The forward/reverse rotation control, which is on
top of the trigger, is positioned in the lock function.
Unlock the forward/reverse rotation control by putting
it into the required rotation position. Push the trigger
and the drill will start to rotate.
2. THE DRILL STOPS BEFORE THE SCREW IS COMPLETELY
TIGHTENED. WHY?
Verify the torque position of the variable clutch, you
can find the variable clutch between the chuck and
the drill body. Position 1 is the lowest torque (screw
driving force) and position 20 is the highest torque
(screw driving force). Position 21 is for drill operation.
Regulate the variable clutch to a higher position to
reach the best result.
3. I CANNOT FIT THE BATTERY INTO THE BATTERY
CHARGER. WHY?
The battery can be inserted into the charger only in
one direction. Turn the battery around until it can be
inserted into the slot, the red LED light should turn on
when the battery is charging.
4. REASONS FOR DIFFERENT CHARGING TIMES.
Your charge time can be affected by many reasons,
which are not defects in your product. If the battery
pack is only partly discharged it may be re-charged
in less than 1 hour. If the battery pack and ambient
temperature are very cold then re-charging may take
1 to 1-1/2 hours. If the battery pack is very hot it will
not re-charge because the internal temperature safety
cutout will prevent it. If the battery pack is very hot
you must remove your battery pack from the charger
and allow your battery pack to cool first to ambient
temperature and then recharging can be started. If
you charge a second battery pack immediately after
the first then the charger can be overheated. Always
allow at least 15 minutes rest between battery pack
charging.
10
EN
5. REASONS FOR DIFFERENT BATTERY PACK WORKING
TIMES.
Charging time issues, as above, and having not used
a battery pack for a prolonged time will reduce the
working life of the battery pack. This can be corrected
after several charge and discharge operations by
charging & working with your drill. Heavy working
conditions such as large screws into hard wood will
use up the battery pack energy faster than lighter
working conditions. Do not re-charge your battery
pack below 0oC and above 30oC as this will affect
performance.
MAINTENANCE
Remove the battery pack from the tool before
carrying out any adjustment, servicing or
maintenance.
Your tool requires no additional lubrication or maintenance.
There are no user serviceable parts in your tool,
battery pack or charger. Never use water or chemical cleaners to clean your tool. Wipe clean with a dry
cloth. Always store your tool in a dry place. Keep the
motor ventilation slots clean.
Staple your purchase receipt here
Before returning this product for
warranty or any other reason, please call.
POSITEC AUSTRALIA PTY LIMITED
ABN 14 101 682 357
Unit 15, 23 Narabang Way Belrose 2085 NSW
Australia
FREE CALL 1300 889 028
EMAIL:office.sales@positec.com.au
Copyright © 2013, Positec. All Rights Reserved.
Made In PRC
Download PDF
Similar pages