Correcting Misalignment for Printing and Cutting When Using

Thank you very much for purchasing this product.
 To ensure correct and safe usage with a full understanding of this product's performance, please be
sure to read through this manual completely and store it in a safe location.
 Unauthorized copying or transferral, in whole or in part, of this manual is prohibited.
 The contents of this document and the specifications of this product are subject to change without
notice.
 The documentation and the product have been prepared and tested as much as possible. If you find any
misprint or error, please inform us.
 Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage which may occur
through use of this product, regardless of any failure to perform on the part of this product.
 Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage which may occur
with respect to any article made using this product.
For EU Countries
Manufacturer:
ROLAND DG CORPORATION
1-6-4 Shinmiyakoda, Kita-ku, Hamamatsu-shi, Shizuoka-ken, 431-2103 JAPAN
The authorized representative in the EU:
Roland DG Corporation, German Office Halskestr. 7, 47877 Willich, Germany
1
For the USA
FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE
STATEMENT
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated
in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference
to radio communications.
Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Unauthorized changes or modification to this system can void
the users authority to operate this equipment.
NOTICE
Grounding Instructions
In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce
the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a
grounding plug. The plug must be plugged into a matching
outlet that is properly installed and grounded in accordance
with all local codes and ordinances.
Do not modify the plug provided - if it will not fit the outlet,
have the proper outlet installed by a qualified electrician.
Check with a qualified electrician or service personnel if the
grounding instructions are not completely understood, or if in
doubt as to whether the tool is properly grounded.
Use only 3-wire extension cords that have 3-prong grounding
plugs and 3-pole receptacles that accept the tool's plug.
Repair or replace damaged or worn out cord immediately.
Operating Instructions
KEEP WORK AREA CLEAN. Cluttered areas and benches
invites accidents.
For Canada
CLASS A
NOTICE
DON’T USE IN DANGEROUS ENVIRONMENT. Don’t
use power tools in damp or wet locations, or expose them to
rain. Keep work area well lighted.
This Class A digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
DISCONNECT TOOLS before servicing; when changing
accessories, such as blades, bits, cutters, and like.
CLASSE A
REDUCE THE RISK OF UNINTENTIONAL STARTING.
Make sure the switch is in off position before plugging in.
AVIS
Cet appareil numérique de la classe A respecte toutes les
exigences du Règlement sur le matériel brouilleur du
Canada.
USE RECOMMENDED ACCESSORIES. Consult the
owner’s manual for recommended accessories. The use of
improper accessories may cause risk of injury to persons.
NEVER LEAVE TOOL RUNNING UNATTENDED. TURN
POWER OFF. Don’t leave tool until it comes to a complete
stop.
For California
WARNING
This product contains chemicals known to cause cancer, birth defects and other reproductive harm,
including lead.
For EU Countries
WARNING
This is a Class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
This product is using GNU General Public License (GPL) / GNU Lesser General Public License (LGPL) software. You have the right to acquire, modify, and distribute the source code for this GPL/LGPL software. You
can obtain the GPL/LGPL source code used in this product by downloading it from the following website.
URL: http://www.rolanddg.com/gpl/
Roland DG Corp. has licensed the MMP technology from the TPL Group.
2
Contents
To Ensure Safe Use.................................................................................................................... 6
Pour utiliser en toute sécurité................................................................................................. 13
Important Notes on Handling and Use .......................................................................................... 20
Printer Unit................................................................................................................................. 20
Ink Cartridges............................................................................................................................. 21
Chapter 1 Introduction..................................................................................................................... 23
1-1 Introduction.......................................................................................................................... 24
Machine Features.........................................................................................................................................................................24
About the Notation Used in This Manual............................................................................................................................24
1-2 Part Names and Functions.................................................................................................. 25
Printer Unit......................................................................................................................................................................................25
Operation Panel............................................................................................................................................................................27
Chapter 2 Operation......................................................................................................................... 29
2-1 Switching the Power On and Off.......................................................................................... 30
Switching the Power On and Off............................................................................................................................................30
The Power-saving Feature.........................................................................................................................................................31
2-2 Loading and Cutting Off Media............................................................................................ 32
Loading Media...............................................................................................................................................................................32
Cutting Off the Media.................................................................................................................................................................38
2-3 Settings for the Media Heating System................................................................................ 39
What Is the Media Heating System?......................................................................................................................................39
Making the Temperature Setting for the Media Heating System...............................................................................39
General Guide for the Preset Temperatures........................................................................................................................40
2-4 Starting Output..................................................................................................................... 41
Getting Ready to Receive Data from a Computer............................................................................................................41
Printing Tests and Cleaning......................................................................................................................................................42
2-5 If Ink Runs Out..................................................................................................................... 43
Checking for Remaining Ink.....................................................................................................................................................43
If Ink Runs Out...............................................................................................................................................................................44
2-6 Performing Cutting .............................................................................................................. 45
To Perform Cutting .....................................................................................................................................................................45
Performing a Cutting Test..........................................................................................................................................................46
Making the Setting for Blade Force ......................................................................................................................................47
Chapter 3 Maintenance and Adjustment................................................................................................................................................49
3-1 Daily Care and Maintenance................................................................................................ 50
Disposing of Discharged Ink....................................................................................................................................................50
Cleaning...........................................................................................................................................................................................52
Care and Maintenance of the Print Heads...........................................................................................................................52
3-2 When Head Cleaning Is Not Effective.................................................................................. 53
Performing More Powerful Cleaning....................................................................................................................................53
When Powerful Cleaning Is Not Effective............................................................................................................................53
3-3 Cleaning the Heads Using the Cleaning Kit......................................................................... 54
When the Cleaning Kit Becomes Necessary.......................................................................................................................54
How to Perform Cleaning..........................................................................................................................................................54
3-4 Replacing Consumable Parts.............................................................................................. 58
Replacing the Wipers..................................................................................................................................................................58
Replacing the Blade.....................................................................................................................................................................61
Replacing the Separating Knife...............................................................................................................................................64
3-5 When Not in Use for a Prolonged Period............................................................................. 66
Keep Performing Maintenance...............................................................................................................................................66
3
Contents
Chapter 4 Feature Reference........................................................................................................... 67
4-1 Pausing or Canceling Output............................................................................................... 68
Canceling Output Before It Finishes......................................................................................................................................68
4-2 Setting the Location for Starting Output............................................................................... 69
Setting the Output-start Location..........................................................................................................................................69
4-3 Saving the Printer Settings to Match the Media................................................................... 70
Saving Optimized Media Settings As Preset Values.........................................................................................................70
Loading a Saved Preset..............................................................................................................................................................71
Assigning a Name to a Preset...................................................................................................................................................71
4-4 Optimizing Printing or Cutting to Match Media Thickness................................................... 72
Adjusting Head Height to Match Media Thickness (54-inch Model Only)...............................................................72
Correcting for Misalignment in Bidirectional Printing....................................................................................................73
Correcting for Misalignment in Bidirectional Printing More Precisely......................................................................74
Performing Feed Correction to Alleviate Horizontal Bands and the Like................................................................76
Performing Distance Correction During Cutting . ...........................................................................................................77
4-5 Accommodating Various Kinds of Media.............................................................................. 78
Using Transparent Media...........................................................................................................................................................78
Printing Hard-to-dry Media......................................................................................................................................................78
Preventing Media from Coming Loose.................................................................................................................................79
Speeding Up Output for Narrow Media...............................................................................................................................79
Preventing Soiling of the Media and Dot Drop-out During Printing........................................................................80
Printing Media That Warps Easily . .........................................................................................................................................81
How to Load Sheet Media ........................................................................................................................................................82
4-6 Changing How the Printer Operates.................................................................................... 84
Executing Environment Matching Automatically.............................................................................................................84
Determining What Happens When Ink Runs Out.............................................................................................................84
Setting the Interval until Activation of the Sleep Mode.................................................................................................85
Deactivating the Sleep Mode..................................................................................................................................................85
Changing the Menu Language and the Units of Measurement.................................................................................86
Returning All Settings to Their Initial Values......................................................................................................................86
4-7 Changing the Ink-drying Method.......................................................................................... 87
Switching Off the Print Heater and Dryer............................................................................................................................87
Determining How the Media Heating System Operates................................................................................................87
Drying the Trailing Edge of the Printing Area on the Dryer..........................................................................................88
4-8 Making Various Adjustments for Cutting.............................................................................. 89
Making the Cutting Conditions Set on the Machine Take Precedence.....................................................................89
Fine-tuning the Cutting Conditions .....................................................................................................................................89
Accurately Adjusting the Cutting-in Amount ...................................................................................................................91
Preventing Pulling of the Media with Undue Force When Performing Cutting Only . .......................................91
Correcting Misalignment of the Printing and Cutting Positions .................................................................................92
4-9 Performing Printing and Cutting Separately......................................................................... 95
To Perform Printing and Cutting Separately.......................................................................................................................95
Printing with Crop Marks...........................................................................................................................................................95
Aligning Automatically and Cutting......................................................................................................................................96
Aligning Manually and Cutting...............................................................................................................................................97
Correcting Misalignment for Printing and Cutting When Using Crop Marks.........................................................98
4-10 Making the Network Settings........................................................................................... 101
Setting the IP Address, Subnet Mask, Etc......................................................................................................................... 101
4-11 Viewing Information about the Media and the System..................................................... 102
Displaying the Amount of Media Remaining.................................................................................................................. 102
Verifying the Setting for the Amount Remaining Every Time the Media Is Changed...................................... 102
Printing the Amount of Remaining Media....................................................................................................................... 103
Viewing the Serial Number, Firmware Version, and Other Information................................................................ 104
Viewing the Network Settings.............................................................................................................................................. 104
Printing a System Report........................................................................................................................................................ 105
4
Contents
4-12 Performing Maintenance.................................................................................................. 106
Draining Ink and Performing Internal Washing.............................................................................................................. 106
Draining Ink Remaining Inside the Machine................................................................................................................... 106
4-13 Menu List......................................................................................................................... 108
Main Menu................................................................................................................................................................................... 108
Language and Unit Menu....................................................................................................................................................... 112
Function Menu........................................................................................................................................................................... 113
Chapter 5 What to Do If.................................................................................................................. 115
5-1 The Machine Doesn't Run.................................................................................................. 116
The Printer Unit Doesn't Run................................................................................................................................................. 116
The Media Heating System Doesn't Warm Up................................................................................................................ 116
5-2 Attractive Printing or Cutting Is Impossible........................................................................ 117
Printed Results Are Coarse or Contain Horizontal Stripes.......................................................................................... 117
Colors Are Unstable or Uneven............................................................................................................................................ 117
The Media Becomes Soiled When Printed........................................................................................................................ 118
Cutting Is Misaligned or Skewed......................................................................................................................................... 118
5-3 The Media Jams................................................................................................................ 119
The Media Jams.......................................................................................................................................................................... 119
5-4 Media Wrinkles or Shrinks, or Feed Is Unstable................................................................ 120
Media Wrinkles or Shrinks...................................................................................................................................................... 120
Media Feed Is Not Straight..................................................................................................................................................... 120
Media Feed Is Not Smooth..................................................................................................................................................... 120
5-5 The Print Heads Stopped Moving...................................................................................... 121
What to Do First......................................................................................................................................................................... 121
If the Heads Still Do Not Move.............................................................................................................................................. 121
5-6 If a Message Appears........................................................................................................ 122
5-7 If an Error Message Appears............................................................................................. 123
Chapter 6 Specifications................................................................................................................ 125
6-1 Usable Media..................................................................................................................... 126
Conditions for Usable Media................................................................................................................................................. 126
6-2 Printing/Cutting Area.......................................................................................................... 127
Maximum Area........................................................................................................................................................................... 127
Maximum Area When Using Crop Marks.......................................................................................................................... 127
The Media-cutoff Location During Continuous Printing............................................................................................ 128
6-3 About the Blade ................................................................................................................ 129
6-4 Locations of the Power Rating and Serial Number Labels................................................ 130
6-5 Specifications..................................................................................................................... 131
Company names and product names are trademarks or registered trademarks of their respective holders.
Copyright © 2008 Roland DG Corporation
http://www.rolanddg.com/
5
To Ensure Safe Use
Improper handling or operation of this machine may result in injury or damage to property. Points which
must be observed to prevent such injury or damage are described as follows.
About
WARNING and
WARNING
CAUTION
CAUTION Notices
Used for instructions intended to alert the user to the risk of death or severe
injury should the unit be used improperly.
Used for instructions intended to alert the user to the risk of injury or material
damage should the unit be used improperly.
Note: Material damage refers to damage or other adverse effects caused
with respect to the home and all its furnishings, as well to domestic
animals or pets.
About the Symbols
The symbol alerts the user to important instructions or warnings. The specific meaning
of the symbol is determined by the design contained within the triangle. The symbol at
left means "danger of electrocution."
The
symbol alerts the user to items that must never be carried out (are forbidden).
The specific thing that must not be done is indicated by the design contained within the
circle. The symbol at left means the unit must never be disassembled.
The
symbol alerts the user to things that must be carried out. The specific thing that
must be done is indicated by the design contained within the circle. The symbol at left
means the power-cord plug must be unplugged from the outlet.
6
To Ensure Safe Use
Incorrect operation may cause injury.
WARNING
Be sure to follow the operation procedures described in this documentation.
Never allow anyone unfamiliar with the
usage or handling of the machine to
touch it.
Incorrect usage or handling may lead to an
accident.
Keep children away from the machine.
The machine includes areas and components
that pose a hazard to children and may result
in injury, blindness, choking, or other serious
accident.
Never operate the machine while tired or
after ingesting alcohol or any medication.
Operation requires unimpaired judgment. Impaired judgment may result in an accident.
Never use the machine for any purpose
for which it is not intended, or use the
machine in an undue manner that exceeds its capacity.
Doing so may result in injury or fire.
For accessories (optional and consumable items, power cord, and the like), use
only genuine articles compatible with
this machine.
Incompatible items may lead to an accident.
CAUTION
Exercise caution to avoid being pinched
or becoming caught.
Inadvertent contact with certain areas may
cause the hand or fingers to be pinched or
become caught. Use care when performing
operations.
Never attempt operation while wearing a
necktie, necklace, or loose clothing. Bind
long hair securely.
Such items may become caught in the machine, resulting in injury.
Conduct operations in a clean, brightly lit
location.
Working in a location that is dark or cluttered
may lead to an accident, such as becoming
caught in the machine as the result of an inadvertent stumble.
Never climb or lean on the machine.
The machine is not made to support a person. Climbing or leaning on the machine may
dislodge components and cause a slip or fall,
resulting in injury.
Caution: cutting tool
This machine has an internal tool. To avoid injury, handle the tool with care.
Before attempting cleaning, maintenance,
or attachment or detachment of optional
items, disconnect the power cord.
Attempting such operations while the machine
is connected to a power source may result in
injury or electrical shock.
Never attempt to disassemble, repair, or
modify the machine.
Doing so may result in fire, electrical shock,
or injury. Entrust repairs to a trained service
technician.
7
To Ensure Safe Use
Danger of electrical short, shock, electrocution, or fire
WARNING
Connect to an electrical outlet that complies with this machine’s ratings (for voltage, frequency, and current).
Incorrect voltage or insufficient current may
cause fire or electrical shock.
Ratings
WARNING
Handle the power cord, plug, and electrical outlet correctly and with care. Never
use any article that is damaged.
Using a damaged article may result in fire or
electrical shock.
When using an extension cord or power
strip, use one that adequately satisfies
the machine’s ratings (for voltage, frequency, and current).
Use of multiple electrical loads on a single
electrical outlet or of a lengthy extension cord
may cause fire.
Connect to ground.
This can prevent fire or electrical shock due to
current leakage in the event of malfunction.
Never use out of doors or in any location
where exposure to water or high humidity may occur. Never touch with wet
hands.
Doing so may result in fire or electrical
shock.
Never allow any foreign object to get
inside. Never expose to liquid spills.
Inserting objects such as coins or matches
or allowing beverages to be spilled into the
ventilation ports may result in fire or electrical
shock. If anything gets inside, immediately
disconnect the power cord and contact your
authorized Roland DG Corp. dealer.
Never place any flammable object nearby.
Never use a combustible aerosol spray
nearby. Never use in any location where
gases can accumulate.
Combustion or explosion may be a danger.
8
Position so that the power plug is within
immediate reach at all times.
This is to enable quick disconnection of the
power plug in the event of an emergency.
Install the machine next to an electrical outlet.
Also, provide enough empty space to allow
immediate access to the electrical outlet.
If sparking, smoke, burning odor, unusual sound, or abnormal operation occurs,
immediately unplug the power cord.
Never use if any component is damaged.
Continuing to use the machine may result in
fire, electrical shock, or injury. Contact your
authorized Roland DG Corp. dealer.
To Ensure Safe Use
Important notes about the power cord, plug, and electrical outlet
Never place any object on top or
subject to damage.
Never allow to get wet.
Never bend or twist with undue force.
Never make hot.
Never pull with undue force.
Dust may cause fire.
Never bundle, bind, or roll up.
9
To Ensure Safe Use
Ink, cleaning fluid, and discharged fluid are flammable and toxic.
WARNING
CAUTION
If you’re using a model that uses ECOSOL MAX ink, keep open flame away
from the work area. Keep open flame
away from the work area.
Ink and discharged fluid are flammable.
Ensure adequate ventilation for the work
area.
Failing to perform ventilation may result in a
health hazard or danger of combustion due
to ink fumes.
Never store ink, cleaning fluid, or discharged fluid in any of the following
locations.
 Any location exposed to open flame
 Any location where high temperature
may occur
 Near bleach or any other such oxidizing agent or explosive material
 Any location within the reach of children
Fire may be a danger. Accidental ingestion by
children may pose a health hazard.
Never allow an ink cartridge to be subjected to impact, and never attempt to
disassemble.
Ink may leak.
Never place an ink cartridge in fire.
Ink may flow out, catch fire, and spread fire to
other nearby objects.
Never drink or sniff ink, cleaning fluid, or
discharged fluid, or allow them to come
in contact with the eyes or skin.
Doing so may be hazardous to the health.
In the event of ingestion or physical distress
 In the event of contact with the eyes, immediately flush with water for at least 15 minutes. If eye irritation continues, seek
treatment by a physician.
 In the event of contact with skin, immediately wash with soap. If irritation or inflammation occurs, seek treatment by a
physician.
 In the event of ingestion, do not induce vomiting, and immediately seek treatment by a physician. Forcibly inducing
vomiting may lead to danger of choking.
 If odor leads to physical distress, move to a well-ventilated location and rest quietly. If dizziness or nausea persists, seek
treatment by a physician.
10
To Ensure Safe Use
This machine weighs 160 kg (353 lb.). Media weighs 30 kg (66 lb.).
WARNING
WARNING
Install the machine in a location that is
level, stable, and able to bear the weight
of the machine.
The total weight of the machine may reach 160
kg (353 lb.) or more (120 kg (265 lb.) or more for
the 30-inch model). Installation in an unsuitable
location may cause a major accident, including
tipover, fall, or collapse.
Unloading and emplacement are operations
that must be performed by six persons or
more (by four persons or more for the 30inch model).
Tasks that require undue effort when
performed by a small number of persons may
result in physical injury. Also, if dropped, such
items may cause injury.
Be sure to lock the stand's casters.
If the machine should begin to topple, a
major accident may result, including crushing
of the appendages or the body.
When storing roll media, implement
adequate safety measures to ensure
that the stored media will not roll, fall, or
topple over.
Danger exists of becoming pinned under the
media and suffering serious injury.
Handling roll media is an operation that
must be performed by two persons or
more, and care must be taken to prevent
falls.
Attempting to lift heavy media in a manner that
taxes your strength may cause physical injury.
Danger of fire, burns, or toxic gas emissions
WARNING
Caution: high temperatures
Areas such as the dryer become hot. Exercise
caution to avoid fire or burns.
When printing is not being performed,
remove any loaded media or switch off
the power.
The continued application of heat at a single
location may cause the release of toxic gases
from the media or pose a fire hazard.
WARNING
Never use media that cannot withstand
heat.
Doing so may degrade the media, or may
result in fire or the release of toxic gases.
11
To Ensure Safe Use
Warning Labels
Warning labels are affixed to make areas of danger immediately clear. The meanings of these labels are as
follows. Be sure to heed their warnings.
Also, never remove the labels or allow them to become obscured.
Caution: Pinching Hazard
Be careful not to allow the fingers to
become pinched when loading media or
closing covers.
Caution: Moving Print Heads
The print heads inside the cover move
at high speed and pose a hazard. Never
insert the hand or fingers into the gap.
Flammable
Ink and discharged fluid are flammable.
Keep away from open flame.
Ink Is Toxic
Ink and discharged fluid are toxic. Avoid
contact with the body. Use only in a wellventilated area.
Caution: High Temperature
The platen and dryer become hot. Exercise caution to avoid fire or burns.
Flammable
Ink and discharged fluid are flammable.
Keep away from open flame.
Ink Is Toxic
Ink and discharged fluid are toxic. Avoid
contact with the body. Use only in a wellventilated area.
12
Pour utiliser en toute sécurité
La manipulation ou l'utilisation inadéquates de cet appareil peuvent causer des blessures ou des dommages matériels. Les précautions à prendre pour prévenir les blessures ou les dommages sont décrites
ci-dessous.
Avis sur les avertissements
ATTENTION
PRUDENCE
Utilisé pour avertir l'utilisateur d'un risque de décès ou de blessure grave en
cas de mauvaise utilisation de l'appareil.
Utilisé pour avertir l'utilisateur d'un risque de blessure ou de dommage matériel en cas de mauvaise utilisation de l'appareil.
* Par dommage matériel, il est entendu dommage ou tout autre effet indésirable sur la maison, tous les meubles et même les animaux domestiques.
À propos des symboles
Le symbole
attire l'attention de l'utilisateur sur les instructions importantes ou les
avertissements. Le sens précis du symbole est déterminé par le dessin à l'intérieur du
triangle. Le symbole à gauche signifie "danger d'électrocution."
Le symbole avertit l'utilisateur de ce qu'il ne doit pas faire, ce qui est interdit. La chose
spécifique à ne pas faire est indiquée par le dessin à l'intérieur du cercle. Le symbole à
gauche signifie que l'appareil ne doit jamais être démonté.
Le symbole
prévient l'utilisateur sur ce qu'il doit faire. La chose spécifique à faire
est indiquée par le dessin à l'intérieur du cercle. Le symbole à gauche signifie que le fil
électrique doit être débranché de la prise.
Ce document est le guide d’installation pour les appareils VP-540i et VP-300i. Dans le document, les noms suivants sont
utilisés pour établir la différence entre le deux modèles, lorsque c’est nécessaire.
VP-540i
VP-300i
—
—
Modèle de 54 po
Modèle de 30 po
13
Pour utiliser en toute sécurité
L’utilisation incorrecte peut causer des blessures
ATTENTION
S’assurer de suivre les procédures
d’utilisation décrites dans la documentation. Ne jamais permettre à quiconque ne
connaît pas le fonctionnement ou la
manutention de l’appareil de le toucher.
L’utilisation ou la manutention incorrectes
peuvent causer un accident.
Garder les enfants loin de l’appareil.
L’appareil comporte des zones et des
composants qui présentent un danger pour les
enfants et qui pourraient causer des blessures,
la cécité, la suffocation ou d’autres accidents
graves.
Ne jamais faire fonctionner l’appareil
après avoir consommé de l’alcool ou des
médicaments, ou dans un état de fatigue.
L’utilisation de l’appareil exige un jugement
sans faille. L’utilisation avec les facultés
affaiblies pourrait entraîner un accident.
Ne jamais utiliser l'appareil à des fins
autres que celles pour lesquelles il est
conçu. Ne jamais l'utiliser de manière
abusive ou d'une manière qui dépasse sa
capacité.
Le non-respect de cette consigne peut causer
des blessures ou un incendie.
Utiliser uniquement des accessoires
d'origine (accessoires en option, articles
consommables, câble d'alimentation et
autres articles semblables), compatibles
avec l'appareil.
Les articles incompatibles risquent de causer
des accidents.
Débrancher le câble d'alimentation avant
de procéder au nettoyage ou à l'entretien
de l'appareil, et avant d'y fixer ou d'en
retirer des accessoires en option.
Tenter ces opérations pendant que l'appareil
est branché à une source d'alimentation peut
causer des blessures ou un choc électrique.
Ne jamais tenter de démonter, de réparer
ou de modifier l'appareil.
Le non-respect de cette consigne risque de
provoquer un incendie, un choc électrique ou
des blessures. Confier les réparations à un
technicien ayant la formation requise.
14
PRUDENCE
Faire preuve de prudence pour éviter
l'écrasement ou le coincement.
La main ou les doigts peuvent être écrasés ou
coincés s'ils entrent en contact avec certaines
surfaces par inadvertance. Faire preuve de
prudence pendant l'utilisation de l'appareil.
Ne jamais faire fonctionner l'appareil si
on porte une cravate, un collier ou des
vêtements amples. Bien attacher les
cheveux longs.
Ces vêtements ou ces objets peuvent être
coincés dans l'appareil, ce qui causerait des
blessures.
Utiliser l'appareil dans un endroit propre
et bien éclairé.
Travailler dans un endroit sombre ou
encombré peut causer un accident;
l'utilisateur risque, par exemple, de trébucher
malencontreusement et d'être coincé par une
partie de l'appareil.
Ne jamais grimper ni s'appuyer sur la
machine.
La machine n'est pas conçue pour supporter
le poids d'une personne. Grimper ou s'appuyer
sur la machine peut déplacer des éléments
et causer un faux pas ou une chute, ce qui
causerait des blessures.
Attention : outil de coupe.
Cet appareil contient un outil interne. Pour
éviter les blessures, manipuler l'outil avec
soin.
Pour utiliser en toute sécurité
Risque de décharge ou de choc électrique,
d’électrocution ou d’incendie
ATTENTION
Brancher à une prise électrique conforme
aux caractéristiques de cet appareil
(tension, fréquence et courant).
Une tension incorrecte ou un courant insuffisant peuvent causer un incendie ou un choc
électrique.
Caractéristiques
ATTENTION
Manipuler le câble d’alimentation, la fiche
et la prise électrique correctement et
avec soin.
Ne jamais utiliser un article endommagé, car
cela pourrait causer un incendie ou un choc
électrique.
Si une rallonge ou une bande
d’alimentation électrique sont utilisées,
s’assurer qu’elles correspondent aux
caractéristiques de l’appareil (tension,
fréquence et courant).
L’utilisation de plusieurs charges électriques
sur une prise unique ou une longue rallonge
peut causer un incendie.
Mise à la terre.
La mise à la terre peut prévenir un incendie ou
un choc électrique dus à une fuite de courant
en cas de défaillance.
Ne jamais utiliser à l'extérieur ni à un
endroit où l'appareil risque d'être exposé
à de l'eau ou à une humidité élevée. Ne
jamais toucher l'appareil avec des mains
mouillées.
Le non-respect de cette consigne risque
de provoquer un incendie ou un choc électrique.
Ne jamais insérer d’objet étranger dans
l’appareil. Ne jamais exposer l’appareil
aux déversements de liquides.
L'insertion d'objets comme des pièces de
monnaie ou des allumettes, ou le déversement de liquides dans les orifices de ventilation peuvent causer un incendie ou un choc
électrique. Si un objet ou du liquide s'infiltre
dans l'appareil, débrancher immédiatement le
câble d'alimentation et communiquer avec le
représentant Roland DG Corp. autorisé.
Placer l'appareil de façon à ce que la
fiche soit facile d'accès en tout temps.
Ainsi, l'appareil pourra être débranché rapidement en cas d'urgence. Installer l'appareil
près d'une prise électrique. En outre, prévoir
suffisamment d'espace pour que la prise électrique soit facile d'accès.
S'il se produit des étincelles, de la fumée,
une odeur de brûlé, un bruit inhabituel ou
un fonctionnement anormal, débrancher
immédiatement le câble d'alimentation.
Ne jamais utiliser si un composant est
endommagé.
Continuer à utiliser l'appareil peut causer un
incendie, un choc électrique ou des blessures.
Communiquer avec le représentant Roland
DG Corp. Autorisé.
Ne jamais placer d’objet inflammable à
proximité de l’appareil. Ne jamais utiliser de produit inflammable en aérosol à
proximité de l’appareil. Ne jamais utiliser
l’appareil dans un endroit où des gaz
peuvent s’accumuler.
Une combustion ou une explosion pourraient
se produire.
15
Pour utiliser en toute sécurité
Remarques importantes à propos du câble d'alimentation, de la fiche et de la prise électrique
Ne jamais déposer aucun objet sur le câble, sur la fiche
ou sur la prise car cela risque de les endommager.
Ne jamais laisser l'eau toucher le câble, la
fiche ou la prise.
Ne jamais plier ni tordre le câble avec une
force excessive.
Ne jamais chauffer le câble, la fiche ou la
prise.
Ne jamais tirer sur le câble ou la fiche avec
une force excessive.
La poussière peut causer un incendie.
Ne jamais plier ni enrouler le câble.
16
Pour utiliser en toute sécurité
L'encre, les liquides nettoyants et les liquides
usées sont inflammables et toxiques
ATTENTION
S’il s’agit d’un modèle qui utilise l’encre
ECO-SOL MAX, ne pas approcher une
flamme nue de l’espace de travail.
L'encre et les liquides usés sont inflammables.
Ne jamais entreposer d'encre, de liquide
de nettoyage ou des liquides usés dans
les endroits suivants :
 un endroit exposé à une flamme nue;
 un endroit où il y a risque de température élevée;
 près d'eau de Javel, d'un autre agent
d'oxydation ou de matériel explosif;
 tout endroit à la portée d'enfants.
Il y a risque d'incendie. L'ingestion accidentelle
par un enfant peut présenter un risque pour
la santé.
PRUDENCE
S'assurer que le lieu de travail est bien
aéré.
L'absence d'aération adéquate peut créer
une situation dangereuse pour la santé ou un
risque de combustion à cause des vapeurs
qui émanent de l'encre.
Ne jamais soumettre une cartouche
d'encre à des chocs. Ne jamais tenter
d'ouvrir une cartouche d'encre.
De l'encre pourrait s'échapper.
Ne jamais incinérer une cartouche
d'encre.
De l'encre pourrait couler, s'enflammer et le
feu se répandre à des objets proches.
Ne jamais boire l'encre, le liquide de
nettoyage ni les liquides usés, ne pas en
respirer les vapeurs et ne pas laisser les
produits entrer en contact avec les yeux
ou la peau.
Cela est dangereux pour la santé.
En cas d'ingestion ou de trouble physique
 En cas de contact avec les yeux : rincer immédiatement et abondamment à l'eau courante pendant au moins 15 minutes.
Si les yeux sont toujours irrités, consulter un médecin.
 En cas de contact avec la peau : laver immédiatement à l'eau et au savon. En cas d’irritation ou d’inflammation de la peau
: consulter un médecin.
 En cas d'ingestion : ne pas provoquer le vomissement et demander immédiatement l'aide d'un médecin. Provoquer le
vomissement peut créer un risque de suffocation.
 Si l'odeur cause un trouble physique, amener la personne dans un endroit bien aéré et la faire se reposer. Si l'étourdissement
ou la nausée persistent, consulter un médecin.
17
Pour utiliser en toute sécurité
Le poids de cet appareil est de 160 kg (353 lb.)
Le poids du support est de 30 kg (66 lb.)
ATTENTION
Installer l'appareil à un endroit stable et
plat et capable de supporter son poids.
Le poids total de l’appareil peut être de 160
kg (353 lb.) ou plus (120 kg (265 lb.) ou plus
pour le modèle de 30 po). Installer l'appareil
à un endroit inapproprié peut provoquer un
accident grave comme le renversement, la
chute ou l'écrasement.
Le déchargement et la mise en place
doivent être faits par au moins six personnes (quatre personnes ou plus pour
le modèle de 30 po).
Les tâches qui exigent un effort trop grand si
elles sont exécutées par un petit nombre de
personnes peuvent être cause de blessures.
La chute d'articles très lourds peut aussi
causer des blessures.
ATTENTION
S'assurer de verrouiller les roulettes de
la base.
Si l'appareil devait commencer à basculer, il
s'ensuivrait un accident grave, par exemple
l'écrasement de membres ou du corps.
Prendre les mesures de sécurité adéquates pour l'entreposage des rouleaux
de support pour s'assurer qu'ils ne
rouleront pas, ne tomberont pas et ne se
renverseront pas.
Il y a risque d'être écrasé par le support et de
subir des blessures graves.
La manutention du support en rouleau
doit être faite par deux personnes ou
plus et il faut prendre des précautions
pour éviter les chutes.
Tenter de soulever des objets trop lourds peut
causer des blessures.
Risque d'incendie, de brûlures ou d'émissions de gaz toxiq
ATTENTION
Attention : températures élevées.
Les zones comme le séchoir chauffent. Faire
preuve de prudence pour éviter un incendie
ou des brûlures.
Quand aucun travail d'impression
n'est en cours, retirer tout support de
l'appareil ou couper l'alimentation électrique.
L'application continue de chaleur à un point
unique peut causer l'émission de gaz toxiques
ou créer un risque d'incendie.
18
ATTENTION
Ne jamais utiliser un support qui ne peut
pas supporter la chaleur.
L'utilisation d'un support qui ne supporte pas
la chaleur peut détériorer le support, créer un
risque d'incendie ou causer l'émission de gaz
toxiques.
Pour utiliser en toute sécurité
Vignettes d'avertissement
Des vignettes d'avertissement sont apposées pour qu'il soit facile de repérer les zones
dangereuses. La signification des vignettes est donnée ci-dessous. Respecter les avertissements.
Ne jamais retirer les vignettes et ne pas les laisser s'encrasser.
Attention : Risque de pincement
Faire attention de ne pas coincer les
doigts pendant le chargement du support
ou lors de la fermeture du couvercle.
Attention : Têtes d'impression mobiles
Les têtes d'impression sous le couvercle
se déplacent à haute vitesse et représentent un danger.Ne jamais insérer la main
ou les doigts dans l'ouverture.
Inflammable
L'encre et les liquides usés sont inflammables. Les garder loin de toute flamme
nue.
L'encre est toxique
L'encre et les liquides usés sont toxiques. Éviter tout contact avec le corps.
Utiliser uniquement dans un endroit bien
aéré.
Attention : Température élevée
La platine et la surface de séchage atteignent des températures élevées.
Être prudent pour éviter un incendie ou
des brûlures.
Inflammable
L'encre et les liquides usés sont inflammables. Les garder loin de toute flamme
nue.
L'encre est toxique
L'encre et les liquides usés sont toxiques. Éviter tout contact avec le corps.
Utiliser uniquement dans un endroit bien
aéré.
19
Important Notes on Handling and Use
This machine is a precision device. To ensure the full performance of this machine, be sure to observe the
following important points. Failure to observe them may not only result in loss of performance, but may also
cause malfunction or breakdown.
Printer Unit
This machine is a precision device.
Handle carefully, and never subject the machine to impact or excessive force.
Never needlessly put your hand or fingers inside the cover, the ink-cartridge ports, or other internal
areas of the machine.
Install in a suitable location.
Install in a location having the specified temperature and relative humidity.
Install in a quiet, stable location offering good operating conditions.
The print heads are delicate.
Never needlessly touch or allow media to scrape them. Failure to handle with care may cause damage.
The print heads may be damaged if allowed to dry out. The machine prevents desiccation automatically, but improper operation may render this feature inoperative. Operate properly, as specified in this
manual.
Never allow the machine to stand with an ink cartridge removed. Remaining ink in the printer may
harden and clog the print heads.
The print heads are components that wear out. Periodic replacement is required, with the frequency
of replacement depending on use.
This machine becomes hot.
Never cover the ventilation holes with cloth, tape, or anything else.
20
Important Notes on Handling and Use
Ink Cartridges
Ink cartridges come in various types.
Use a type that is compatible with the printer. Also, be sure to use only genuine items from Roland DG
Corp.
Never subject to impact or attempt to disassemble.
Never drop or shake forcefully. The impact may rupture the internal pouch and cause the ink to leak.
Never attempt to disassemble.
Never attempt to refill the ink.
If ink gets on your hands or clothing, wash it off as soon as possible. Removal may become difficult if
allowed to stand.
Storage
Store unopened in a well-ventilated location at a temperature of -20 to 40°C (-4 to 104°F).
21
22
1
Introduction
2
Operation
Chapter 1
Introduction
3
Part Names and Functions...................................................................................25
Maintenance and
Adjustment
Introduction...........................................................................................................24
4
Feature
Reference
5
What to Do If
6
Specifications
23
1-1 Introduction
1
Machine Features
Introduction
This is a signmaking machine that adds cutting features to a printer capable of high image quality, for a machine that
can accommodate a wide variety of uses, ranging from the creation of stickers and cut-out text and small-lot label
printing to the production of panels, outdoor signs, and more.
This makes possible not only use as either a printer or a cutting machine, but also enables consecutive
printing and cutting. Using the crop-mark feature makes it possible to perform alignment and carry out
cutting when you want to reload printed media that has been detached for lamination or the like.
2
A built-in print server enables direct connection to a network.
Operation
This machine has a built-in media heating system composed of a print heater to improve ink adhe-
sion and speed up drying and a dryer to speed up drying of the media after printing. This enhances
productivity by enabling support for more types of media.
A software raster image processor (RIP) is included as a standard feature. It takes output data such
as a PostScript file received from a program, performs raster image processing on the computer, and
outputs the data to the machine.
3
Installing a media take-up system (available separately) enables automatic take-up of the media
Maintenance and
Adjustment
during printing. This enables unattended operation at night and lengthy printing to be accomplished
efficiently.
About the Notation Used in This Manual
4
This document is the user's manual for both the VP-540i and the VP-300i. This document uses the following notation to
distinguish between the two models where necessary.
Feature
Reference
VP-540i
VP-300i
—
—
54-inch model
30-inch model
Also, most of the figures in this document depict the VP-540i.
5
What to Do If
6
Specifications
24
1-2 Part Names and Functions
You operate this when you
load media.
Front cover
Be sure to close this when
you perform output.
Side cover
Introduction
Loading lever
1
Printer Unit
Operation panel
You use this to perform variYou remove this when you ous operations.
perform maintenance.
 P. 27, "Operation Panel"
2
Operation
Drain bottle
Maintenance cover
3
This collects drained ink
and other such fluids. Dis­
card any collected fluid
before it overflows.
You remove this when
you perform cleaning the
print head.
Maintenance and
Adjustment
4
Status LED
Main power switch
This lights up green when the con­
nection to the network is correct.
Power-cord connector
This supplies power to the printer.
Connector
Feature
Link LED
Reference
This flashes yellow while data is being
received from the network.
Ethernet connector
This is employed when you’re
us­ing the media take-up system
available separately.
This is used to connect the printer to a network.
5
These indicate the locations of the grit rollers. You
use them as guides for positioning the left and right
sides when loading media.
What to Do If
Grit patterns
Cartridge slots
There are where ink cartridges are installed.
6
Specifications
25
1-2 Part Names and Functions
1
Grit patterns
Introduction
These indicate the locations of the grit
rollers. The pinch rollers must always
be placed within the area indicated by
each of these patterns.
Grit rollers
Left and right pinch
rollers
These rollers feed out media toward
the front of the machine.
These clamp the media when
the loading lever is lowered.
Middle pinch rollers
2
These are detachable and
remountable pinch rollers.
The number that can be used
varies according to the width
of the media.
Print-head carriage
Operation
The print heads are inside
this.
3
Maintenance and
Adjustment
Cutting carriage
The blade and the separating knife are inside here.
Blade protector
Media clamps
This protects the tip of the
blade during cutting.
Platen
4
This is the path over which the
media passes. A suction fan that
keeps the media from coming
loose and print heater that helps
fix the ink are built in.
Feature
Reference
5
What to Do If
6
Specifications
26
Apron
These keep the media from
coming loose and prevent
fuzz on the cut edge of the
media from touching the
print heads.
This has a built-in dryer to
speed up drying of the ink.
1-2 Part Names and Functions
1
Operation Panel
Introduction
HEATER light
Display screen
This flashes while the media
heating system is warming up,
changing to a steadily lighted
state when the pre­set temperature is reached.
This displays various setting
menus and other informa­tion.
BASE POINT light
This lights up when the base
point (the output-start loca­tion)
has been set.
2
PAUSE key
FUNCTION key
You press this when entering
the setting menu for clean­ing
of the print heads, print­ing tests,
and so on.
Operation
This pauses printing opera­
tion. This lights up when op­
eration is paused.
ENTER key
Cursor keys
You use this for such tasks as
enabling setting values.
You use these to select settings for menu items, to move
the media, and for other such
operations.
BUSY light
Sub power switch
This switches the printer on and off.
(To switch the printer off, you hold
down the switch for one second or
longer). The light flashes slowly when
the machine is in the sleep mode.
SETUP light
This lights up when media has
been loaded correctly.
4
Panel Notation
Feature
Cursor keys
5
What to Do If
SETUP light
BUSY light
BASE POINT light
HEATER light
Reference
In this document, the keys and lights on the operation panel are indicated by the following images.
MENU key
FUNCTION key
ENTER key
PAUSE key
Maintenance and
You press this to enter the
menus for various settings.
Adjustment
MENU key
3
This lights up during print­
ing, cutting and other such
operations.
6
Specifications
27
28
1
Introduction
2
Operation
Chapter 2
Operation
3
Loading and Cutting Off Media.............................................................................32
Settings for the Media Heating System................................................................39
Starting Output......................................................................................................41
If Ink Runs Out......................................................................................................43
Maintenance and
Adjustment
Switching the Power On and Off...........................................................................30
Performing Cutting ...............................................................................................45
4
Feature
Reference
5
What to Do If
6
Specifications
29
2-1 Switching the Power On and Off
1
Switching the Power On and Off
Introduction
This machine has a main power switch and a sub power switch. When using the machine, you switch both on in this sequence:
first the main power, then the sub power.
Whenever output is finished, switch off the sub power. Also, raise the loading lever.
Leave the main power switch
on at all times, never switching it off.
WARNING
When output is not being performed, remove any loaded media or switch off the
sub power.
2
The continued application of heat at a single location may cause the release of toxic
gases from the media or pose a fire hazard.
Operation
Main power switch Be sure to leave
switched on at
all times.
3
Maintenance and
Adjustment
Keep the loading lever raised
when the machine is not in use.
4
Sub power switch Turn this switch on after
closing the front cover.
To turn it off, hold down
the switch for one second or longer.
Feature
Reference
5
Important Note on Switching Off the Power
What to Do If
Never switch off the main power or unplug the power cord suddenly while operation is in progress. Doing
so may damage the print heads. Be sure to first switch off the sub power.
If the main power is accidentally switched off, immediately turn the power back on.
6
Specifications
30
2-1 Switching the Power On and Off
1
The Power-saving Feature
Introduction
This machine is provided with a power-saving feature that switches to a low-power "sleep mode" when a fixed interval passes
with no operation. The factory default for the time after which the machine switches to the sleep mode is 30 minutes.
You can change the setting for the time of the shift to the sleep mode. You can also switch off the power-saving feature.
P. 85, "Setting the Interval until Activation of the Sleep Mode," p. 85, "Deactivating the Sleep Mode"
2
When the machine is in the sleep mode, the sub power switch flashes slowly and the media heating system stops.
Using the operation panel or performing operations such as sending output data from the computer (when media is loaded)
restores the machine to its normal mode.
Operation
To reduce power consumption and prevent problems such as overheating, we recommend leaving the power-saving feature
on and setting the activation time for the sleep mode to 30 minutes or less.
3
Maintenance and
Adjustment
4
Feature
Reference
5
What to Do If
6
Specifications
31
2-2 Loading and Cutting Off Media
1
Loading Media
Introduction
Media may be of one of two types: media wound onto a paper tube (called “roll media”) and media not rolled in this way
(called “sheet media”). This section explains how to load media, using roll media as an example. For information on how to
load sheet media, refer to the page indicated below.
P. 82, "How to Load Sheet Media"
CAUTION
Load roll media correctly.
Otherwise the media may fall and cause injury.
2
Operation
CAUTION
Roll media weighs about 30 kg (66 lb.). To avoid injury, handle with care.
CAUTION
Never load media that weighs more than 30 kg (66 lb.) (or, for the 30-inch model,
more than 20 kg (44 lb.)).
The machine may fail to withstand the weight and tip over or cause the media to
fall.
1. Pass the media through the machine and position it correctly on the left and right.
3
 Open the front cover.
Move the media clamps to the sides.
Maintenance and
Adjustment
Media clamps
4
Feature
Reference
 Attach the media flanges to the roll media.
5
If the inner diameter of the roll-media core measures 3 inches, fit the media flanges onto the core, then turn each
knob clockwise all the way to keep the media flanges from falling out.
What to Do If
2 inches
3 inches
Match to the inner
diameter of the rollmedia core.
Press in to
fit on securely.
6
Roll-media
Specifications
Knob
32
Turn until the knob
stops rotating.
2-2 Loading and Cutting Off Media
1
 Place the roll media on the shafts and position its left and right edges to match the grit
patterns.
Introduction
Be sure to ensure the
media is within this range.
20 mm or more
20 mm or more
2
Operation
 Secure the stoppers in place in alignment with the width of the media.
Make sure the media flanges are straight. Correct media feed is impossible if either of the media flanges is at an
angle.
3
4
Screws
Not OK
 Pass the leading edge of the media between the grit rollers and the pinch rollers, and feed
5
it out as far as the platen.
Feature
Reference
OK
Maintenance and
Adjustment
Stoppers
What to Do If
Pinch roller
Platen
6
Grit roller
Specifications
33
2-2 Loading and Cutting Off Media
1
 Make sure both edges of the media are above the grit rollers, then place pinch rollers over
all grit rollers covered by the media.
Introduction
Placing the pinch rollers inside each of the grit patterns ensures that they are positioned above the grit rollers.
Be sure to place the left and right pinch rollers (affixed with blue stickers) at the edges of the media. Arrange the middle
pinch rollers above all the grit rollers that lie between the left and right pinch rollers.
Be sure to remove any extra middle pinch rollers, leaving only the same number of middle pinch rollers as the number
of grit rollers.
Place the pinch
roller inside the
grit pattern.
Left pinch roller
Affixed with a blue sticker.
2
Right pinch roller
Affixed with a blue
sticker.
Operation
Grit pattern
Position this at
locations that is not
overly close to the
edge of the media.
About
10 mm
Position this at
locations that is
not overly close
About to the edge of
10 mm the media.
3
Maintenance and
Adjustment
4
Be sure to place the right edge of
the media on these grit rollers.
Feature
Reference
Attaching and Detaching Middle Pinch Rollers
Perform attachment or detachment at the location shown in the figure.
Slide along the rail.
Attachment/
detachment location
5
What to Do If
Insert all the way.
6
Specifications
34
Pull back and out.
2-2 Loading and Cutting Off Media
1
2. Secure the media in place so that it is without slack.
Introduction
 Hold the media at the center and pull it out, being sure to keep it straight.
Make sure all areas of the media are taut.
2
Operation
3
 Lower the loading lever to hold the media in place.
starts to flash, and then the screen shown in the figure appears.
Maintenance and
Not OK
Adjustment
OK
4
Feature
Reference
Operation
Panel
5
What to Do If
Flashing
Loading lever
6
Specifications
35
2-2 Loading and Cutting Off Media
1
3. Clamp the edges of the media with the media clamp.
Introduction
 Move the media clamps as shown in the figure below.
2
Operation
3
Maintenance and
Adjustment
Left media clamps
Right media clamps
Line up the edge of the media
with the centers of the holes.
Line up the edge of the media
with the centers of the holes.
4
Feature
Reference

Close the front cover.
5
What to Do If
W1200mm
When initialization ends,
is displayed.
remains steadily lighted, and the printable width
6
This completes loading of the media.
Specifications
36
2-2 Loading and Cutting Off Media
Important Note When Using the Media Clamps
1
Set the media clamps at the correct locations. If they are not set at the correct locations, the media
Introduction
may catch, preventing successful printing.
As printing proceeds, the media may move to the left or right and touch or come loose from the media
2
clamps. After about 1 m (3 ft.) of media has been fed, check the positioning of the media clamps. If
the media looks like it may come loose from the media clamps, adjust the positioning of the media
clamps.
Moving a media clamp to the right edge of the platen as shown in the figure below may cause it to be
hidden by the cutting carriage and make it impossible to detach the media clamp without further action.
If this happens, first load the media, then lower the loading lever. After
lights up, use
to
move the cutting carriage to a location where it doesn’t obstruct the media clamp, then detach or move
the media clamp.
Operation
Rightmost grit
pattern
Pinch roller
Media clamp
3
Cutting carriage
4
If the message shown in the figure appears when you close the front cover, check the positions of the pinch rollers and the
middle pinch rollers. These must be placed over the grit rollers. Also, if the number of middle pinch rollers installed is greater
than the number of grit rollers used, then detach the extra middle pinch rollers.
Maintenance and
Adjustment
Position the pinch rollers over the grit rollers.
Feature
Reference
Pinch rollers
Either RIGHT or
LEFT is displayed.
5
What to Do If
Middle pinch rollers
This indicates which pinch roller, counting
from the right as viewed from the front, is
displaced. (The right pinch roller is included
in the count.)
The number displayed may be from the second ("2ND") to the sixth ("6TH"), depending
on the number used.
6
Remove when not using roll media.
Specifications
If roll media is allowed to stand unused in a loaded state for an extended period, the media may sag. This can cause
poor printing quality and motor errors, so be sure to remove and store such media when not in use.
37
2-2 Loading and Cutting Off Media
1
Cutting Off the Media
Introduction
Procedure
 Close the front cover.
lights up.
Make sure
 FUNCTION
SHEET CUT
2
 Press
Press
Press
.
several times.
.
Operation
The media is cut off.
The cutoff location on the media is as shown in the figure below.
Blade protector The media is fed
to the front.
3
Press
Blade protector
The media is
cut off here.
.
Maintenance and
Adjustment
Printed portion
You can make the setting in the software RIP for automatic media cutoff after printing or cutting has finished. For
information on how to make the setting, refer to the documentation for the software RIP you're using.
4
Important Notes on Using the Long Media Clamps
Feature
Reference
When you're using the long media clamps, be sure to set the [MEDIA CLAMP] menu item to [LONG]
to disable media cutoff. Performing cutting the media when the long media clamps are installed causes
interference with the separating knife, which may result in malfunction or damage to the machine.
If you want to separate the media after printing has finished, be sure to first detach the long media clamps,
then set the [MEDIA CLAMP] menu item to a setting other than [LONG].
 P. 81, "Printing Media That Warps Easily"
5
Give Attention to Media Composition
What to Do If
For some types of media, cutoff is not possible.
Some types of media may remain on the platen after cutoff. If the media remains on the platen, remove
it by hand.
When you cut off media while using the short media clamps, then depending on the media, it may
come loose from the media clamps. After you cut off the media, check to make sure that the media
has not come loose from the media clamps.
Before you're performing cutoff, never use
to pull the media back.
6
Specifications
Unless the end of the media has been pulled out to a location to the front of the platen, cutoff may not
be performed smoothly.
38
2-3 Settings for the Media Heating System
1
What Is the Media Heating System?
Introduction
This machine is equipped with a media heating system that warms the media. You use this mainly to improve ink adhesion
and dry the ink. You can adjust the temperature settings to match the type of media and the printing speed.
Print heater
This heater is used mainly to improve ink
adhesion.
Dryer
You use this to speed up drying of the ink.
2
WARNING
Operation
WARNING
Caution: high temperatures
The platen and dryer become hot. Exercise caution to avoid fire or burns.
Remove any loaded media or switch off the sub power when printing is not being
performed.
Doing so may result in fire or the release of toxic gases, or may degrade the media.
Never use the platen or dryer for any purpose for which they are not intended,
such as to dry clothing.
Doing so may cause overheating, resulting in fire or accident.
Maintenance and
WARNING
Never use media that cannot withstand the heat.
Adjustment
WARNING
3
The continued application of heat at a single location may cause fire or produce
toxic gases.
4
Procedure

FUNCTION
HEATER CONFIG
Press
Press
.

HEATER CONFIG
DRYER
34 C
Press
Use
(dryer).
.
Press
Use
Press
.
Press
to go back to the original screen.

W1200mm
SETUP SHEET
40 C
to make the setting.
to enable the setting.
6
DRYER
35 C
to select [PRINT] (print heater) or [DRYER]
What to Do If

several times.
5
Present dryer temperature
Feature
Reference
Making the Temperature Setting for the Media Heating System
Specifications
By default, simply switching on the power does not make the media heating system warm up to the preset temperature.
When media is loaded correctly and
comes on, warm-up to the preset temperature occurs.
39
2-3 Settings for the Media Heating System
1
General Guide for the Preset Temperatures
Introduction
The optimal temperature for the media heating system varies according to such factors as the type of media and differences
in the print mode. Use the following as a general guide and adjust accordingly.
General Guide for Adjustment
Print heater
2
You use this mainly to improve ink adhesion and inhibit smudging.
If the ink forms lumps or smudges, raise the temperature. Note, however, that a temperature that is too high may degrade
the media or cause it to wrinkle.
Operation
Dryer
When ink drying is poor, raise the temperature. Note, however, that a temperature that is too high may degrade the media
or cause it to wrinkle.
The relationship between the print mode and temperature
If smudging or poor drying occur even after raising the temperature, try using a print mode offering higher image quality.
Conversely, when you want to use a faster print mode, raise the temperature.
3
Amount of ink
Maintenance and
Adjustment
When you change the amount of ink using the settings for your software RIP, adjusting this may yield better results. If problems such as smudging persist even after raising the temperature, try reducing the amount of ink.
When suggested settings for temperature, print mode, and other values are given, use the suggested
settings.
Use at an ambient temperature of 20 to 32°C (68 to 90°F).
4
Feature
Reference
If the machine is used at an ambient temperature lower than 20°C (68°F), then depending on the type or width of the media,
wrinkling or temperature-caused unevenness may occur. If this happens, try lowering the temperature of the media heating
system by about 2°C.
To obtain stable printing results, however, the machine should be used at an ambient temperature of 20 to 32°C (68 to
90°F).
5
What to Do If
6
Specifications
40
2-4 Starting Output
1
Getting Ready to Receive Data from a Computer
Introduction
When you have finished loading media and making the temperature settings for the media heating system, then follow the
steps below. This procedure enables the machine to receive data from the computer and perform output. When printing
data that includes cutting paths is received, you can also carry out cutting immediately after performing printing.
Note, however, that when you want to perform only cutting, operation that differs from the following procedure is required.
 P. 45, "To Perform Cutting"
Never touch the print heads while output is in progress.
2
CAUTION
Operation
The print heads move at high speed. Contact may cause injury.
Procedure
 Close the front cover.
stays steadily lit.
 Make sure
If the light does not come on, lower the loading lever.
.
Flashing
Top menu
Steadily lighted
Maintenance and
, then press
Adjustment
If the top menu is not displayed, press
3
stops flashing and stays steadily lit.
 Wait until
 Make sure the top menu is displayed.
4
5
Output Is Not Possible in These Situations
Feature
Reference
Steadily lighted
What to Do If
The machine does not run when the front cover is open. Also, never open it when printing is in progress.
Doing so interrupts printing.
Data from the computer is not accepted when
is dark.
Printing does not start until
lights up.
Data from the computer is not accepted when you are not at the top menu.
Points Which Must Be Observed
6
Be sure to set the media clamps during printing. Otherwise the edges of the media may warp and
catch on the print heads.
Specifications
During output, never touch the media that's already been discharged. Doing so may obstruct media
feed or cause the media to rub against the heads, which may result in a paper jam or damage to the
heads.
41
2-4 Starting output
1
Printing Tests and Cleaning
Introduction
Before you carry out actual printing, we recommend performing a printing test to ensure no dot drop-out occurs. If dot
drop-out occurs, perform cleaning.
How to Perform a Printing Test
2
Operation
 FUNCTION
CLEANING
Press
Press
.
.
 CLEANING
TEST PRINT
Press
.

Dot drop-out
Press
.
A test pattern is printed.
You can freely set the location for printing the test
pattern.
 P. 69, "Setting the Output-start Location"
3
Maintenance and
Adjustment
How to Perform Cleaning
4
Feature
Reference
 FUNCTION
CLEANING
Press
Press
.
.
 CLEANING
NORMAL
Press
Press
.
.
 CLEANING...
>>
Press
.
5
CLEANING
NORMAL
What to Do If
 W1200mm
Cleaning starts.
When it finishes, the screen shown in the figure appears again.
Press
to go back to the original screen.
SETUP SHEET
 Perform a printing test again to make sure the dot drop-out has been corrected.
6
If the problem persists, try performing cleaning a second time.
If the problem doesn't go away even after performing cleaning two or three times, then try cleaning using a different
method.
 P. 53, "When Head Cleaning Is Not Effective"
Specifications
42
2-5 If Ink Runs Out
1
Checking for Remaining Ink
 MENU
INK REMAINING
1
2
3
4
Press
Press
.
Press
.
Press
to go back to the original screen.
several times.
2
Operation
 W1200mm
Introduction
Procedure
SETUP SHEET
Amount of ink remaining
Much
Cartridge slot number
1
2
3
4
3
Maintenance and
Adjustment
Little
The display shows an approximate guide to the amount of remaining ink, which may differ somewhat
from the actual amount remaining.
4
Feature
Reference
5
What to Do If
6
Specifications
43
2-5 If Ink Runs Out
1
If Ink Runs Out
Introduction
When ink runs out, a warning beep sounds and printing pauses (unless the default settings have been changed). Pull out
the empty cartridge and insert a new one. Printing resumes.
Procedure
1
2
3
4
2
Operation

The slot number for the empty cartridge flashes.
Gently shake the new cartridge.
 Pull out the empty cartridge and immediately insert the new one.
3
Maintenance and
Adjustment
Replace with an item of identical type
and color.
4
Feature
Reference
○ Keep the labeled side face up.
○ Insert and remove slowly, one at a time.
○ Insert firmly, as far as it will go.
Important Notes on Replacing Cartridges
5
What to Do If
Be sure to replace with an item of identical type. Never mix items of different types.
Never allow the machine to stand with an ink cartridge removed. The print heads may become
clogged.
Never insert or remove a partially used ink cartridge.
Never remove an ink cartridge suddenly while the printer is in operation.
When printing is paused, the coloring at the seam may be altered when printing resumes. Before you
perform lengthy printing, check the amount of ink remaining in the ink cartridges.
6
WARNING
Specifications
44
If you’re using a model that uses ECO-SOL MAX ink, never store ink, cleaning
fluid, or discharged fluid in any of the following locations.
Any location exposed to open flame
Any location where high temperature may occur
Near bleach or any other such oxidizing agent or explosive material
Any location within the reach of children
Fire may be a danger. Accidental ingestion by children may pose a health hazard.
2-6 Performing Cutting
1
To Perform Cutting
Introduction
To perform cutting, carry out the procedure described below.
Move
the media clamps to locations where they don’t clamp the media. Alternatively,
remove the media clamps.
Media clamps
2
Operation
3
you're performing cutting only, then if you're cutting roll media, allow the media to
hang down from the rear of the machine.
If cutting is started without doing this first, a motor error may occur or the roll may fall because the media is pulled
with excessive force.
Maintenance and
Adjustment
When
4
Feature
Reference
Turn the media flanges by
hand to pull out the necessary length from the roll.
5
What to Do If
Important Notes on Cutting
Never use the media clamps. You can also detach them when not in use.
 P. 81, "Printing Media That Warps Easily"
6
When you’re performing printing followed immediately by cutting, then before you start cutting, allow
Specifications
the ink to dry sufficiently. Use your software RIP to make the setting for the drying time. For information
on how to make the setting, refer to the documentation for the software RIP you're using. The drying
time varies according to the media.
45
2-6 Performing Cutting
1
Hints and Tips for Cutting
Setting the [PREFEED] menu item to “ENABLE” makes the machine automatically feed out media and
Introduction
take it up again before cutting. This makes it unnecessary to run out media to the rear of the machine
before the operation.
 P. 91, "Preventing Pulling of the Media with Undue Force When Performing Cutting Only"
When you're performing cutting, switching off the print heater and dryer and allowing the temperature
to cool before performing cutting can yield results that are more stable.
 P. 87, "Switching Off the Print Heater and Dryer"
The end of the cap for the blade holder may scrape or damage the printed surface. If this happens,
2
increase the amount of blade extension.
Operation
 P. 91, "Accurately Adjusting the Cutting-in Amount"
Performing a Cutting Test
3
For high-quality cutting, then before you perform actual cutting, we recommend carrying out a cutting test to check the
cutting quality for the media.
Maintenance and
Adjustment
Performing a Cutting Test
 Use
to carry out the cutting test.
to move the cutting carriage to the location where you want
You can freely set the location for the cutting test.
4
Feature
Reference
 FUNCTION
CUT CONFIG
Press
Press
.
several times.
CONFIG
 CUT
TEST CUT
Press
.

Rectangle
Close the front cover.
.
Press
The test pattern is cut.
Circle
5
What to Do If
 Peel off the cut shapes to verify the cutting quality.
If two shapes peel off together, make the setting for blade force.
 P. 47, "Making the Setting for Blade Force"
6
Specifications
46
2-6 Performing Cutting
1
Making the Setting for Blade Force
 FUNCTION
CUT CONFIG
Press
Press
.
CONFIG
 CUT
FORCE
Press
Press
.
 FORCE
50 gf
60 gf
Press
Use
.
 FORCE
60 gf
60 gf
several times.
several times.
2
Operation
 W1200mm
Press
Introduction
Procedure
to enter the value.
.
This completes the settings.
Press
to go back to the original screen.
SETUP SHEET
3
Maintenance and
Adjustment
At the [CUT CONFIG] menu, you can also make settings for other cutting conditions in addition to the blade force. Refer to
the following pages.
 P. 89, "Fine-tuning the Cutting Conditions"
4
Feature
Reference
5
What to Do If
6
Specifications
47
48
1
Introduction
2
Operation
Chapter 3
Maintenance and Adjustment
3
When Head Cleaning Is Not Effective...................................................................53
Cleaning the Heads Using the Cleaning Kit..........................................................54
Replacing Consumable Parts...............................................................................58
When Not in Use for a Prolonged Period..............................................................66
Maintenance
and Adjustment
Daily Care and Maintenance................................................................................50
4
Feature
Reference
5
What to Do If
6
Specifications
49
3-1 Daily Care and Maintenance
1
Disposing of Discharged Ink
Introduction
The drain bottle collects discharged fluid. Dispose of collected material before the bottle becomes full. The message shown
in the figure appears when a certain amount of discharged fluid has collected in the bottle. Follow the procedure below to
discard the discharged fluid.
CHECK
DRAIN BOTTLE
Resetting the discharged-fluid counter after disposal makes the message shown in
the figure disappear.
2
Press
Operation
1. Choose the "DRAIN BOTTLE" menu item.
3
Maintenance
and Adjustment
 MENU
SUB MENU
Press
Press
.
several times.
MENU
 SUB
MAINTENANCE
Press
Press
.
.
 MAINTENANCE
DRAIN BOTTLE
Press
Press
.
.
 EMPTY
Press
.
DRAIN BOTTLE
Preparations are complete when this screen appears.
2. Empty the bottle by discarding the discharged fluid.
4
CAUTION
Feature
Reference
Before you detach the drain bottle, be sure to wait for the screen to display "EMPTY
DRAIN BOTTLE."
Failing to follow this procedure may cause discharged fluid to flow out of the tube
and spill, soiling your hands or the floor.
5
What to Do If
Upper limit
Discard before this line
is passed.
6
Specifications
50
3-1 Daily Care and Maintenance
Press
.
 MAINTENANCE
DRAIN BOTTLE
Press
a second time.
 W1200mm
Press
to go back to the original screen.
Introduction
 RESET DRAIN
COUNTER
1
3. Attach the emptied bottle and reset the discharged-fluid count.
The screen shown in the figure appears.
CAUTION
Operation
WARNING
2
SETUP SHEET
Never place discharged fluid near open flame.
Doing so may cause fire.
To store discharged fluid temporarily, place it in the included drain bottle or in
a durable sealed container such as a metal can or polyethylene tank, and cap
tightly.
Any spillage or vapor leakage may cause fire, odor, or physical distress.
3
Maintenance
and Adjustment
Dispose of discharged fluid properly, in accordance with the laws in effect in your locale.
Discharged fluid is flammable and contains toxic ingredients. Never attempt to incinerate discharged fluid
or discard it with ordinary trash. Also, do not dispose of it in sewer systems, rivers, or streams. Doing so
may have an adverse impact on the environment.
4
Feature
Reference
5
What to Do If
6
Specifications
51
3-1 Daily Care and Maintenance
1
Cleaning
Introduction
Pinch rollers
Periodically wipe away any grime. Failure
to clean properly may result in the transfer of grime to the surface of media.
Grit rollers
2
Remove buildup of media and other
material using a brush. Never use a
metal brush.
Operation
Wipe away any buildup of ink or grime
on the media path.
3
WARNING
Maintenance
and Adjustment
CAUTION
Never use gasoline, alcohol, thinner, or any other flammable material.
Doing so may cause fire.
Before attempting cleaning, switch off the sub power and wait until the platen and
dryer cool (approximately 30 minutes).
Sudden movement of the machine may cause injury, or hot components may cause
burns.
This machine is a precision device, and is sensitive to dust and dirt. Perform cleaning on a daily ba-
sis.
4
Clean by wiping with a cloth moistened by neutral detergent diluted with water then wrung dry.
Never attempt to oil or lubricate the machine.
Feature
Reference
Care and Maintenance of the Print Heads
Daily Care and Maintenance
5
Perform maintenance using the machine's head cleaning feature.
 P. 42, "Printing Tests and Cleaning," p. 53, "When Head Cleaning Is Not Effective"
What to Do If
Periodic Care and Maintenance
Periodic care is essential to ensuring optimal printing at all times. Based on your frequency of use, periodically clean the
heads using a cleaning kit.
P. 54, "Cleaning the Heads Using the Cleaning Kit"
Note: The print heads are components that wear out. Periodic replacement is required depending on the
frequency of use. Purchase them from your authorized Roland DG Corp. dealer.
6
Specifications
52
3-2 When Head Cleaning Is Not Effective
1
Performing More Powerful Cleaning
Introduction
When the problems such as dot drop-out are not cleared up by the "normal cleaning," try the more forceful "medium cleaning" or the even more forceful "powerful cleaning." Note, however, that this consumes more ink than "normal cleaning," and
too-frequent use may damage the print heads themselves. Avoid using it more than necessary.
1. Choose "medium cleaning" or "powerful cleaning."
.
several times.
 CLEANING
MEDIUM CL.
Press
Use
CL."
.
Operation
Press
Press
2
 FUNCTION
CLEANING
to choose "MEDIUM CL." or "POWERFUL
2. Start cleaning.
.
CHECK
DRAIN BOTTLE
The screen shown in the figure appears, then cleaning starts.
When it finishes, the screen shown in the figure appears. Go on to Step.
If You Chose "POWERFUL CL."
The screen shown in the figure appears. Go on to Step.
4
 Check the drain bottle.
 P. 50, "Disposing of Discharged Ink," step 2.
When it finishes, the screen shown in the figure appears again. Go on to Step.
Press
to go back to the original screen.
What to Do If
 W1200mm
.
The screen shown in the figure appears, then cleaning starts.
5
CLEANING
POWERFUL CL.
Press
Feature
Reference
If the amount of discharged fluid is near the upper-limit line, then remove the bottle, discard
the collected fluid, and reattach the bottle.
 CLEANING...
>>
Maintenance
CLEANING
MEDIUM CL.
If You Chose "MEDIUM CL."
and Adjustment
CLEANING...
>>
3
 Press
SETUP SHEET
When Powerful Cleaning Is Not Effective
6
Specifications
If problems such as dot drop-out persist even after you have performed powerful cleaning several times, then use the cleaning kit to clean the heads. Such cleaning can be effective when carried out periodically, according to the frequency of use.
 P. 54, "Cleaning the Heads Using the Cleaning Kit"
53
3-3 Cleaning the Heads Using the Cleaning Kit
1
When the Cleaning Kit Becomes Necessary
Introduction
Periodic Care and Maintenance
Use the cleaning kit to perform head-cleaning periodically, according to the frequency of use.
When Dot Drop-out or the Like Occur Frequently
When the machine's head-cleaning feature does not correct the problem, clean the heads using the cleaning kit.
2
If you use up the cleaning kit, purchase a new one from your authorized Roland DG Corp. dealer.
The print heads are components that wear out. Periodic replacement is required, with the frequency
of replacement depending on use. Purchase them from your authorized Roland DG Corp. dealer.
Operation
How to Perform Cleaning
Important Notes on This Procedure
3
To prevent the heads from drying out, finish this procedure in 30 minutes or less.
A warning beep sounds after 30 minutes. At this time, stop work, and follow the procedure in step 4. on
Maintenance
and Adjustment
page 57 to attach the side cover and the maintenance cover, then close the front cover. Press
to quit the manual-cleaning mode. After that, restart the procedure from the beginning.
Never use any implement other than the included cleaning stick. Cotton swabs or other lint-producing
items may damage the heads.
Never touch the nozzle surface of the heads.
Stroke the sponges very gently, applying as little pressure as possible. Never rub, scrape, or crush
them.
4
CAUTION
Be sure to perform operations as specified by the instructions above, and never
touch any area not specified in the instructions.
Sudden movement of the machine may cause injury.
Feature
Reference
1. Change to the print-head manual-cleaning mode.
 Remove any media.
 MENU
SUB MENU
Press
Press
.
MENU
 SUB
MAINTENANCE
Press
Press
.
.
 MAINTENANCE
CLEANING
Press
.
MAINTE OPEN
NANCE COVER
Press
.
several times.
5
What to Do If
6
Specifications
54
3-3 Cleaning the Heads Using the Cleaning Kit
Introduction
Screw
Open the front cover and remove the
maintenance cover.
1

2
Maintenance
cover
Operation
Screw
 NOW PROCESSING..
Close the front cover and press
.
Open the front cover.
Preparations are complete when this screen appears.
2. Remove the side cover.
Screws
Remove the side cover.
4

Maintenance
and Adjustment
 FINISHED?
3
The print-head carriage moves to the left side of the machine, and then the screen
shown in the figure appears.
CLOSE FRONT
COVER
Feature
Reference
Side cover
5
What to Do If
Hook
6
Specifications
55
3-3 Cleaning the Heads Using the Cleaning Kit
Touch the location shown in the figure
to discharge any static electricity.
1

Introduction
2
Operation
3. Clean using the cleaning stick. Be especially careful to clean away any fibrous dust (lint).
3
Clean in the sequence shown in the figure below.
Maintenance
and Adjustment
Cleaning stick
Be sure to clean using one of the included cleaning sticks.
4
Feature
Reference
Never touch the nozzle
surface.
Clean only the metal frame.
Gently stroke the sponge.
Never rub with force.
5
What to Do If
Area to clean
6
Specifications
56
Area to clean
Area to clean
3-3 Cleaning the Heads Using the Cleaning Kit
Attach the side cover.
Screws
Introduction

1
4. Reattach the side cover and the maintenance cover and quit the manual-cleaning mode.
Side cover
2
Operation
Hook
 CLEANING...
>>
3
Close the front cover.
.
Press
Open the front cover and attach the
maintenance cover.
Screw
Maintenance

and Adjustment
The print-head carriage moves to the right side of the machine, and then the screen
shown in the figure appears.
CLOSE MAINTENANCE COVER
4
Feature
Reference
Maintenance
cover
Screw
5
 Close the front cover.
 SETUP SHEET
.
Press
What to Do If
Press
to go back to the original screen.
5. Perform a printing test to verify the results of the procedure.
6
Specifications
Perform a printing test to check the results.
Perform cleaning using the machine’s cleaning feature several times when necessary.
 P. 42, "Printing Tests and Cleaning"
57
3-4 Replacing Consumable Parts
1
Replacing the Wipers
Introduction
The wipers are components that you use when cleaning the print heads. When the
screen displays a message like the one shown, it means the item needs to be replaced.
Replace with new items.
MAINTENANCE
REPLACE WIPER
Press
CAUTION
Be sure to perform operations as specified by the following instructions, and
never touch any area not specified in the instructions.
2
Sudden movement of the machine may cause injury.
Operation
1. Display the [REPLACE WIPER] menu.
 Remove any media from the platen.
Press
 MENU
SUB MENU
3
Maintenance
and Adjustment
Press
.
several times.
MENU
 SUB
MAINTENANCE
Press
Press
.
.
 MAINTENANCE
REPLACE WIPER
Press
Press
.
.
OPEN SIDE
The print-head carriage moves to a location where wiper replacement is possible, and
then the screen shown in the figure appears.
COVER
4

Screws
Feature
Reference
Side cover
5
What to Do If
Hook
6
Specifications
58
Remove the side cover.
3-4 Replacing Consumable Parts

1
Touch the location shown in the figure
to discharge any static electricity.
Introduction
2
Operation
 FINISHED?
Preparations are complete when this screen appears.
Detach the old wipers.
Detach the hook and pull up and out.
Maintenance
and Adjustment

3
2. Replace the wipers. Use the included tweezers.
4
5
Insert the new wipers.
Felt surface toward
the rear
Feature
Reference

What to Do If
6
Rubber surface
toward the front
Specifications
59
3-4 Replacing Consumable Parts
1

Attach the hook.
Introduction
Hook
2
Operation
3. Reattach the side cover, and quit the wiper replacement mode.

Screws
Attach the side cover.
3
Side cover
Maintenance
and Adjustment
4
Hook
Feature
Reference
 CLEANING...
>>
MAINTENANCE
REPLACE WIPER
Press
.
After the process to quit the wiper replacement mode, the screen shown in the figure
appears.
5
What to Do If
 SETUP SHEET
Press
to go back to the original screen.
 Perform a printing test to verify the results of the procedure.
 P. 42, "Printing Tests and Cleaning"
6
Specifications
60
3-4 Replacing Consumable Parts
1
Replacing the Blade
Introduction
If the blade becomes dull, replace it with the included replacement blade.
CAUTION
Be sure to perform operations as specified by these instructions, and never touch
any area not specified in the instructions.
Sudden movement of the machine may cause injury.
CAUTION
Never touch the tip of the blade with your fingers.
2
Doing so may result in injury.
Press
Press
.
several times.
MENU
 SUB
MAINTENANCE
Press
Press
.
.
 MAINTENANCE
REPLACE KNIFE
Press
Press
.
several times.

Press
.
3
 MENU
SUB MENU
Operation
1. Enter the blade replacement mode.
Maintenance
and Adjustment
The cutting carriage moves to a location where blade replacement is possible, and
then the screen shown in the figure appears.
4
Preparations are complete when this screen appears.
2. Replace the blade.

Feature
Open the front cover.
Reference
 FINISHED?
Remove the blade holder.
5
What to Do If
6
Specifications
61
3-4 Replacing Consumable Parts
1

Introduction
Remove the old blade.
Install a new blade.
Press this pin.
Pin
Blade holder
2
Blade holder
Operation
New blade
Old blade

Support the screw from below and
insert the blade holder.
3
Maintenance
and Adjustment
Insert until the collar is flush with the
surface.
4
Screw
Feature
Reference

5
What to Do If
6
Specifications
62
Tighten the screw.
Tug the blade holder upward to make sure it does
not come loose.
3-4 Replacing Consumable Parts
SETUP SHEET
Close the front cover.
.
Press
to go back to the original screen.
Press
Introduction
 W1200mm
1
3. Quit the blade replacement mode.
2
Operation
3
Maintenance
and Adjustment
4
Feature
Reference
5
What to Do If
6
Specifications
63
3-4 Replacing Consumable Parts
1
Replacing the Separating Knife
Introduction
If the separating knife becomes dull, replace it with the included replacement knife.
CAUTION
Be sure to perform operations as specified by these instructions, and never touch
any area not specified in the instructions.
Sudden movement of the machine may cause injury.
CAUTION
Never touch the tip of the separating knife with your fingers.
2
Doing so may result in injury.
Operation
1. Enter the blade replacement mode.
3
Maintenance
and Adjustment
 MENU
SUB MENU
Press
Press
.
several times.
MENU
 SUB
MAINTENANCE
Press
Press
.
.
 MAINTENANCE
REPLACE KNIFE
Press
Press
.
several times.

Press
.
The cutting carriage moves to a location where blade replacement is possible, and
then the screen shown in the figure appears.
4
 FINISHED?
Feature
Reference
Open the front cover.
Preparations are complete when this screen appears.
2. Replace the separating knife.

Remove the separating knife.
5
Loosen the screw until it slips out.
Grasp the screw portion, and slowly pull it out
in the direction of the arrow. When doing this, do
not pull it back toward you.
What to Do If
6
Specifications
64
3-4 Replacing Consumable Parts

1
Install a new knife.
Magnet
The knife is secured in place by the magnet.
Introduction
2
Positioning
groove

Tighten the screw.
Operation
Slowly insert it into the groove.
3

Maintenance
and Adjustment
4
Feature
Reference
Take care to ensure that the knife does not slip out
of position at this time.
5
What to Do If
3. Quit the blade replacement mode.
SETUP SHEET
Close the front cover.
.
Press
to go back to the original screen.
Press
6
 W1200mm
Specifications
65
3-5 When Not in Use for a Prolonged Period
1
Keep Performing Maintenance
Introduction
Switch On the Power Once a Month
Switch on the sub power once a month. When you turn on the power, the machine automatically performs some operations
such as those to keep the print heads from drying out. Allowing the machine to stand completely unused for a prolonged
period may damage the print heads, so be sure to switch on the power to perform these automatic operations.
Keep at a Constant Temperature and Relative Humidity
2
Even when the machine is not in use, keep it at a temperature of 5 to 40°C (41 to 104°F) and a relative humidity of 20 to 80%
(with no condensation). Temperatures that are too high may degrade the ink and cause malfunction. Temperatures that are
too low may cause the ink to freeze and damage the heads.
Operation
 The Setup Guide also describes what to do when the machine will be out of use for a prolonged period. Be sure to refer to it as well.
3
Maintenance
and Adjustment
4
Feature
Reference
5
What to Do If
6
Specifications
66
1
Introduction
2
Operation
Chapter 4
Feature Reference
3
Setting the Location for Starting Output................................................................69
Saving the Printer Settings to Match the Media....................................................70
Optimizing Printing or Cutting to Match Media Thickness....................................72
Accommodating Various Kinds of Media..............................................................78
Maintenance and
Adjustment
Pausing or Canceling Output................................................................................68
Changing How the Printer Operates.....................................................................84
4
Changing the Ink-drying Method...........................................................................87
Performing Printing and Cutting Separately.........................................................95
Making the Network Settings..............................................................................101
Viewing Information about the Media and the System........................................102
Feature
Reference
Making Various Adjustments for Cutting...............................................................89
Performing Maintenance.....................................................................................106
Menu List............................................................................................................108
5
What to Do If
6
Specifications
67
4-1 Pausing or Canceling Output
1
Canceling Output Before It Finishes
Introduction
Procedure
CANCEL, HOLD
 TODOWN
PAUSE KEY
Press
.
The screen shown in the figure appears.
2
for one second or longer.
 Hold down
 Stop sending output data from the computer.
Operation
Description
pauses printing and cutting.
Pressing
a second time here makes output resume, but in the case of printing, horizontal bands are produced
at the place where output stopped. We do not recommend resuming printing.
3
Maintenance and
Adjustment
4
Feature
Reference
5
What to Do If
6
Specifications
68
4-2 Setting the Location for Starting Output
1
Setting the Output-start Location

Use
the cutting carriage.
Introduction
Procedure
to move
Align the center of the blade with the new outputstart location.
2
Operation
Printing area
Output-start
location
Feed-direction
start location
Scan-direction
start location
3
.
 W1100mm
B
Press
to save.
4
This indicates that the
output-start location has
been set.
Feature
Reference
Feed-direction
Maintenance and
Press
Adjustment
 FUNCTION
BASE POINT
Scan-direction
5
What to Do If
Description
Specifications
If you’re using the separately available media take-up unit, never use
force, resulting in an error or malfunction.
6
You can set the output-start location at any location you prefer. Note, however, that this setting must be made for each individual page. When the printing of one page finishes, the output-start location returns to its default value. When the start
location has been set,
lights up and screen displays the character “B” together with the output-possible width at
the location.
This feature is also available when you're printing or cutting various test patterns, and can help you use media with less waste.
Note, however, that the left and right positions are not restored to their defaults for test patterns.
. Doing so may pull the media with undue
69
4-3 Saving the Printer Settings to Match the Media
1
Saving Optimized Media Settings As Preset Values
Introduction
Procedure
2
Operation
 MENU
PRESET
Press
.
 PRESET
SAVE
Press
Press
.
.
 SAVE
NAME1
Press
Use
"NAME8."
Press
.
Press
to go back to the original screen.
to select any one from "NAME1" to
to save.
The present menu settings are saved in the preset you chose in step.
 W1200mm
SETUP SHEET
3
Description
Maintenance and
Adjustment
Using the [PRESET] menu lets you easily change a wide variety of settings to optimize them for the media.
Making changes for each menu item every time you change the media can be troublesome. That's why it can be useful to
save the menu-item settings optimized for an often-used type of media as a preset. The next time you use the media, you
can change the menu-item settings to the optimal values for the media simply by loading the preset you saved.
Menu items that can be saved in presets are listed below.
[PRINT] (Print heater), [DRYER]
4
 P. 39, "Settings for the Media Heating System"
Feature
Reference
[EDGE DETECTION]
 P. 78, "Using Transparent Media"
[SCAN INTERVAL]
 P. 79, "Preventing Media from Coming Loose"
[FULL WIDTH S]
 P. 79, "Speeding Up Output for Narrow Media"
[FEED FOR DRY]
5
 P. 88, "Drying the Trailing Edge of the Printing Area
What to Do If
on the Dryer"
[CALIBRATION]
(in the [CUTTING MENU])
[ADJUST BI-DIR SIMPLE SETTING]
 P. 73, "Correcting for Misalignment in Bidirectional
Printing"
[ADJUST BI-DIR DETAIL SETTING]
 P. 74, "Correcting for Misalignment in Bidirectional Printing More Precisely"
[CALIBRATION]
 P. 76, "Performing Feed Correction to Alleviate Horizontal
Bands and the Like"
[PRINT-CUT ADJ.]
 P. 92, "Correcting Misalignment of the Printing and
Cutting Positions"
[CROP-CUT ADJ.]
 P. 77, "Performing Distance Correction During Cut-
 98, "Correcting Misalignment for Printing and Cutting
ting"
When Using Crop Marks"
[FORCE], [SPEED], [OFFSET], [UP-SPEED]
6
 P. 89, "Fine-tuning the Cutting Conditions"
[PREHEATING]
 P. 87, "Determining How the Media Heating System
Operates"
Specifications
Up to eight types of presets can be saved. You can assign a name to each one. Using media names for these may aid recognition and clarity.
 P. 71, "Loading a Saved Preset," "Assigning a Name to a Preset"
70
4-3 Saving the Printer Settings to Match the Media
1
Loading a Saved Preset
Introduction
Procedure
 MENU
PRESET
Press
.
 LOAD
NAME1
Press
Use
load.
twice.
 SETUP SHEET
Press
to load.
to select the name of a preset you want to
2
Operation
The settings are changed and the screen shown in the figure appears.
Description
3
This loads a saved preset. You can select any one of eight types of presets. (When no names have been assigned, you select from
among NAME1 through NAME8.) If you load a preset while
is illuminated,
goes dark. If this happens, raise
the loading lever, make sure the media is loaded straight, then lower the loading lever again to make output possible.
Procedure
.
.
twice.

NAME
NAME1
Press
Use
Press
.
.
to select any one from NAME1 to NAME8.
Use
Press

NAME
SAMPLE_
Use
to enter the next character.
Enter the following characters in the same way. When you're fin.
ished entering text, press

W1200mm
SETUP SHEET
Press
.
to enter a character.
What to Do If
NAME
S_
5

Feature
Press
Press
Press
Reference
PRESET
NAME
4

Maintenance and
Adjustment
Assigning a Name to a Preset
to go back to the original screen.
6
Description
Specifications
This assigns a name to a saved preset. Using media names may aid recognition and clarity.
The characters you can enter are "A" through "Z," "0" through "9," and the "-" character. You can enter up to 15 characters,
including spaces.
71
4-4 Optimizing Printing or Cutting to Match Media Thickness
1
Adjusting Head Height to Match Media Thickness (54-inch Model Only)
Introduction
Procedure
 MENU
HEAD HEIGHT
Press
Press
.
several times.
HEIGHT
 HEAD
LOW
LOW
Press
.
2

Operation
High
Low (Standard)
Open the front cover.
Move the height-adjustment lever to adjust
the head height.
3
Maintenance and
Adjustment
Height-adjustment lever
Move firmly, until it stops.
4
 MENU
HEAD HEIGHT
Close the front cover.
 W1200mm
Press
The print-head carriage moves to the original position, and then the screen shown
in the figure appears.
to go back to the original screen.
Feature
Reference
SETUP SHEET
Description
5
Depending on the media, media may wrinkle or come loose from the platen during printing, increasing the chance of contact
with the print heads. When you are using such media, adjust the head height to "HIGH." (On the 30-inch model, the head
height cannot be changed.)
Printing quality when the head height is set to “HIGH” may be coarser or otherwise lower than when set to “LOW.” If this happens, refer to the pages indicated below.
 P. 73 "Correcting for Misalignment in Bidirectional Printing," p. 74, "Correcting for Misalignment in Bidirectional Printing More
What to Do If
Precisely," p. 80, "Preventing Soiling of the Media and Dot Drop-out During Printing"
6
Specifications
72
4-4 Optimizing Printing or Cutting to Match Media Thickness
1
Correcting for Misalignment in Bidirectional Printing
Introduction
Procedure
1. Print a test pattern.
.
.
BI-DIR
 ADJUST
TEST PRINT
Press
Press
.
to start printing.
Operation
Press
Press
2
 MENU
ADJUST BI-DIR
2. Read the correction values from the test pattern.
Choose the value that produces
the least misalignment.
Test pattern
3
Correction-value scale
Current correction value
.
SETTING
 SIMPLE
-6
0
Press
Use
Press
.
to set the correction values.
to enable the setting.
Press
to go back to the original screen.
What to Do If
W1200mm
5
4. Go back to the original screen.
Feature
Press
Reference
BI-DIR
 ADJUSUT
SIMPLE SETTING
4
3. Enter the correction values that you read.
Maintenance and
Adjustment
Simple
Description
6
The bidirectional-printing mode (in which the heads perform printing during both their outbound pass and return pass)
offers the advantage of being able to shorten output times, but subtle misalignment occurs during the outbound and return passes. The procedure to correct this and eliminate misalignment is bidirectional correction. This misalignment varies
according to the head height and the thickness of the media, so we recommend performing correction to match the media
you're using.
This settings also serves to correct for misalignment of the printing and cutting positions. In such cases, check or adjust
this setting.
Specifications
P. 92, "Correcting Misalignment of the Printing and Cutting Positions," p. 98, "Correcting Misalignment for Printing and Cutting
When Using Crop Marks"
73
4-4 Optimizing Printing or Cutting to Match Media Thickness
1
Correcting for Misalignment in Bidirectional Printing More Precisely
Introduction
Procedure
1. Print a test pattern.
2
Operation
 MENU
ADJUST BI-DIR
Press
Press
.
.
BI-DIR
 ADJUST
DETAIL SETTING
Press
Press
.
.
BI-DIR
 ADJUST
TEST PRINT
Press
Press
.
to start printing.
2. Read the correction values from the test pattern.
3
Test pattern
Choose the value that produces
the least misalignment.
Maintenance and
Adjustment
H4
H3
H2
H1
NO.4
H4
H3
H2
H1
NO.3
H1
NO.1
H4
H3
H2
H1
NO.2
4
H4
H3
H2
Feature
Reference
5
What to Do If
6
Specifications
74
H1
NO.1
Correction-value scale
Current correction value
4-4 Optimizing Printing or Cutting to Match Media Thickness
1
3. Enter the correction values that you read.
SETTING
 DETAIL
SETTING NO.1
 H10
H2
0
Press
H3
0
 H10
H2
0
Press
H3
0
Press
H3
0
H2
0
Press
.
to select. Use
to set the corUse
rection value.
to finish making the settings for [SETTING NO.4].
Press
5
H4
0
H3
0
.
What to Do If
4. Go back to the original screen.
W1200mm
Press
Feature
 H10
Press
Reference
SETTING
 DETAIL
SETTING NO.4
Press
.
to select. Use
to set the corUse
rection value.
to finish making the settings for [SETTING NO.3].
Press
4
H4
0
.
Maintenance and
H2
0
Press
.
to select. Use
to set the corUse
rection value.
to finish making the settings for [SETTING NO.2].
Press
Adjustment
SETTING
 DETAIL
SETTING NO.3
.
3
H4
0
 H10
Press
.
to select. Use
to set the corUse
rection value.
to finish making the settings for [SETTING NO.1].
Press
Operation
SETTING
 DETAIL
SETTING NO.2
.
2
H4
0
Introduction
Enter the corresponding correction values for H1 through H4.
to go back to the original screen.
6
Description
Specifications
This corrects, for each head, the minute misalignment that occurs in the bidirectional-printing mode. When further correction is required, such as when adjustment made using [SIMPLE SETTING] does not enhance printing, use [DETAIL SETTING]
to make corrections for each head.
75
4-4 Optimizing Printing or Cutting to Match Media Thickness
1
Performing Feed Correction to Alleviate Horizontal Bands and the Like
Introduction
Procedure
1. Print a test pattern.
2
Operation
 MENU
CALIBRATION
Press
Press
.
several times.
 CALIBRATION
TEST PRINT
Press
Press
.
to start printing.
2. Check the test pattern you printed.
Overlap
Gap present
3
Maintenance and
Adjustment
Current correction
value
Choose the one that
has the smallest gap
and the least amount of
overlap.
4
3. Enter the correction value.
Feature
Reference
SETTING
0.00%
-0.40%
Press
Press
Use
Press
.
.
to make the setting for the correction value.
to enable the setting.
4. Go back to the original screen.
5
W1200mm
Press
to go back to the original screen.
What to Do If
Description
6
The movement distance of media experiences subtle changes due to the thickness of the media and the temperature of the
media heating system. When the movement distance becomes discrepant, horizontal stripes are more likely to occur during
printing. We recommend performing correction to match the media you're using and the media heating system. Repeat the
process of printing a test pattern and entering a correction value several times to find the optimal value.
You can also make this setting on the computer (by, for example,choosing the media type in the software RIP you are using).
When you have made the setting on the computer, the computer's setting is used and the printer's setting is ignored.
Specifications
76
4-4 Optimizing Printing or Cutting to Match Media Thickness
1
Default Setting
[SETTING]: 0.00%
Introduction
Performing Distance Correction During Cutting
Procedure
MENU
 CUTTING
CALIBRATION
Press
Press
.
several times.
 CALIBRATION
FEED SETTING
Press
.
SETTING
 FEED
0.00%
0.00%
Press
Use
Press
.
 CALIBRATION
SCAN SETTING
Press
Press
.
.
SETTING
 SCAN
0.00%
0.00%
Press
Use
Press
.
 W1200mm
Press
to go back to the original screen.
3
to make the setting for the correction value.
to enable the setting for [FEED SETTING].
Adjustment
to make the setting for the correction value.
to enable the setting for [SCAN SETTING].
Maintenance and
.
.
Operation
Press
Press
2
 MENU
CUTTING MENU
4
Description
5
The movement distance of the media changes subtly depending on the media's thickness. This means that the length of a
line when cut may differ from the length setting in the data. You enter a correction value when you want to align the lengths
of cut lines precisely.
However, when you’re performing printing followed by cutting, be sure to set the correction value to “0.00%.” Otherwise the
printing and cutting positions may become misaligned.
Feature
Reference
SETUP SHEET
What to Do If
Default Setting
[FEED SETTING]: 0.00%
[SCAN SETTING]: 0.00%
6
Specifications
77
4-5 Accommodating Various Kinds of Media
1
Using Transparent Media
Introduction
Procedure
2
 MENU
SUB MENU
Press
Press
.
several times.
DETECTION
 EDGE
ENABLE
DISABLE
Press
Use
twice.
 SETUP SHEET
Press
to enable the setting.
to select "DISABLE."
Operation
The settings are changed and the screen shown in the figure appears.
Description
3
This setting enables or disables detection of the leading and trailing edges of the media. It is normally set to "ENABLE."
When transparent media is loaded, set it to "DISABLE."
When [EDGE DETECTION] is set to "DISABLE," printing operation does not stop when the media runs out. If media runs out
while printing is in progress, immediately press
to quit printing. Otherwise, there is a chance that the platen or the
like may become soiled by ink or that ink may get inside and damage the machine.
Maintenance and
Adjustment
Default Setting
[EDGE DETECTION]: ENABLE
Printing Hard-to-dry Media
4
Feature
Reference
Procedure
 MENU
SUB MENU
Press
Press
.
several times.
MENU
 SUB
SCAN INTERVAL
Press
Press
.
.
Press
Use
Press
.
Press
to go back to the original screen.
5
 SCAN INTERVAL
OFF
What to Do If
 W1200mm
1.0 sec
.
to set the value.
SETUP SHEET
6
Description
Specifications
You use this when ink dries poorly even when the media heating system is used. Larger values produce progressively slower
movement of the media, enabling you to extend the drying time accordingly. Printing time takes correspondingly longer.
You can also make this setting on the computer. When you have made the setting on the computer, the computer's setting
is used and the printer's setting is ignored.
78
4-5 Accommodating Various Kinds of Media
1
Default Setting
[SCAN INTERVAL]: OFF
Introduction
Preventing Media from Coming Loose
Procedure
.
several times.
MENU
 SUB
VACUUM POWER
Press
Press
.
twice.
POWER
 VACUUM
AUTO
90%
Press
Use
Press
.
 W1200mm
Press
to go back to the original screen.
Operation
Press
Press
2
 MENU
SUB MENU
to set the value.
to enable the setting.
3
Description
4
The platen uses suction to grip the media and keep it stable. When media comes loose from the platen because it is warped
or wrinkled, increasing the suction force may help correct the problem. Conversely, when the media is flimsy and cannot
move smoothly, reducing the suction force may help.
When set to "AUTO," the suction force is automatically adjusted to the optimal level for the media width.
You can also make this setting on the computer. When you have made the setting on the computer, the computer's setting
is used and the printer's setting is ignored.
Maintenance and
Adjustment
SETUP SHEET
Feature
Reference
Default Setting
[VACUUM POWER]: AUTO
5
Speeding Up Output for Narrow Media
What to Do If
Procedure
.
several times.
MENU
 SUB
FULL WIDTH S
Press
Press
.
several times.
WIDTH S
 FULL
FULL
OFF
Press
Use
Press
.
Specifications
Press
Press
6
 MENU
SUB MENU
to select "SHEET" or "OFF."
to enable the setting.
79
4-5 Accommodating Various Kinds of Media
1
 W1200mm
Press
to go back to the original screen.
SETUP SHEET
Introduction
Description
2
This shortens output time by reducing the width of head movement to the minimum necessary. This is effective when the
width of the media or the output data is narrow.
"SHEET" matches the range of head movement to the width of the media.
"OFF" matches the range of head movement to the output data. Movement is limited to the minimum amount necessary,
and this can be expected to yield the fastest output. Note, however, that because the speed of media movement is no
longer constant, colors may be uneven.
"FULL" makes the speed of media movement constant at all times.
Operation
Default Setting
[FULL WIDTH S]: FULL
3
Preventing Soiling of the Media and Dot Drop-out During Printing
Maintenance and
Adjustment
Procedure
4
Feature
Reference
 MENU
SUB MENU
Press
Press
.
several times.
MENU
 SUB
PERIODIC CL.
Press
Press
.
several times.
CL .
 PERIODIC
NONE
10 min
Press
Use
or "PAGE."
Press
.
Press
to go back to the original screen.
 W1200mm
to select a value from "10 min" to "990 min,"
to enable the setting.
SETUP SHEET
5
What to Do If
Description
6
Ink tends to collect on the surface of the heads when you use media prone to buildup of static charge, when the ambient
temperature is low, or when the head height is set to “HIGH.” Under some conditions, this ink may be transferred to the media
or cause dot drop-out. Use this feature at such times. The ink buildup is removed as printing is performed.
When this is set to "PAGE," automatic cleaning is performed every time before printing starts.
When this is set to a value from "10 min" to "990 min," automatic cleaning is performed when the cumulative printing time
reaches the value you set here.
When this is set to "NONE," no automatic cleaning is performed.
Using "PAGE" or a value from "10 min" to "990 min," results in longer printing times. Also, when this is set to a value from "10
min" to "990 min," printing pauses and so colors may be uneven.
 P. 72, "Adjusting Head Height to Match Media Thickness (54-inch Model Only)"
Specifications
80
4-5 Accommodating Various Kinds of Media
1
Default Setting
[PERIODIC CL.]: NONE
Introduction
Printing Media That Warps Easily
Procedure
Press
Press
.
several times.
CLAMP
 MEDIA
SHORT
LONG
Press
Use
Press
.
 W1200mm
Press
to go back to the original screen.
Operation
 MENU
MEDIA CLAMP
2
1. Change the setting for the [MEDIA CLAMP] menu item to [LONG].
to select "LONG."
to enable the setting.
3
SETUP SHEET
Maintenance and
Adjustment
2. Replace the short media clamps with the long ones.
 Remove the short media clamps.
Pull back while holding
down the area.
4
Feature
Reference
Push here.
5
What to Do If
6
Specifications
81
4-5 Accommodating Various Kinds of Media
1
 Attach the long media clamps.
Introduction
Insert until it clicks
into place.
2
Operation
Description
3
When you want to hold the media in place more securely, such as when you're printing media that warps easily, use the long
media clamps to secure the edges of the media in place.
Note that when you're attaching the long media clamps, be sure to make the setting described above so that the mediacutoff operation cannot be performed. Performing media cutoff with the long media clamps installed may cause the long
media clamps to touch the separating knife, resulting in damage or malfunction.
When the [MEDIA CLAMP] menu item is set to [LONG], media cutoff is not performed.
 P. 38, "Cutting Off the Media"
Maintenance and
Adjustment
How to Load Sheet Media
4
Feature
Reference
When you’re loading standard-size media or other such media that is not rolled (sheet media), follow the procedure below.
Procedure

5
What to Do If
6
Specifications
82
Remove both shafts.
If roll media is loaded, then remove the media
first.
4-5 Accommodating Various Kinds of Media

Align the front edge of the media with
the location shown in the figure.
Introduction
Pass the media through the machine.
1

2
Operation
3
4
 Lower the loading lever to secure the media in place.
 If you're performing printing, attach the media clamps and close the front cover.
Maintenance and
Adjustment
Align here
 P. 32, "Loading Media," step 3.
Feature
Reference
See also the following pages.
5
What to Do If
6
Specifications
83
4-6 Changing How the Printer Operates
1
Executing Environment Matching Automatically
Introduction
Procedure
2
Operation
 MENU
CUTTING MENU
Press
Press
.
.
MENU
 CUTTING
AUTO ENV. MATCH
Press
Press
.
.
ENV. MATCH
 AUTO
ENABLE
DISABLE
Press
Use
Press
.
 Press
to select "ENABLE."
to enable the setting.
to go back to the original screen.
Description
3
Maintenance and
Adjustment
This setting enables or disables the feature for automatic adjustment to optimize the state of the machine to the environment
where it is used (temperature and humidity). Performing automatic adjustment can reduce misalignment in the scanning
direction (the direction of carriage movement) during printing or cutting. It is normally set to "ENABLE."
Default Setting
[AUTO ENV. MATCH]: ENABLE
4
Feature
Reference
Determining What Happens When Ink Runs Out
Procedure
5
What to Do If
 MENU
SUB MENU
Press
Press
.
several times.
MENU
 SUB
INK CONTROL
Press
Press
.
twice.
MODE
 EMPTY
STOP
CONT.
Press
Use
Press
twice.
 Press
to make the setting.
to enable the setting.
to go back to the original screen.
Description
6
Specifications
This lets you change, according to your purpose, the operation that takes place when an ink cartridge is empty.
"STOP" immediately pauses operation when a cartridge becomes empty. Because pausing printing in progress may make
colors uneven, it is best to ensure a sufficient amount of remaining ink before you begin printing.
"CONT." (continue) is a mode in which operation is not automatically stopped. When a cartridge becomes empty, a warning
84
4-6 Changing How the Printer Operates
1
beep sounds but printing does not stop. To replace the cartridge, you must either wait until printing ends or press
to pause printing. Note that operation does not stop even if ink runs out completely.
Introduction
Default Setting
[EMPTY MODE]: STOP
Setting the Interval until Activation of the Sleep Mode
2
Procedure
.
several times.

SUB MENU
SLEEP
Press
Press
.
several times.

INTERVAL
30min
Press
Use
Press
twice.

W1200mm
SETUP SHEET
Press
to go back to the original screen.
15min
Adjustment
to make the setting.
to enable the setting.
Maintenance and
Press
Press
Operation
MENU
SUB MENU
3

Default Setting
4
[INTERVAL]: 30min
Feature
Reference
Deactivating the Sleep Mode
Procedure
.
several times.
MENU
 SUB
SLEEP
Press
Press
.
several times.
 SLEEP
SETTING
Press
Press
.
.
Press
Use
Press
.
Press
to go back to the original screen.
to select "DISABLE."
to enable the setting.
Specifications
 W1200mm
DISABLE
6
 SETTING
ENABLE
What to Do If
Press
Press
5
 MENU
SUB MENU
SETUP SHEET
85
4-6 Changing How the Printer Operates
1
Default Setting
[SETTING]: ENABLE
Introduction
Changing the Menu Language and the Units of Measurement
Procedure
2
LANGUAGE
 MENU
ENGLISH
Operation
Hold down
Use
Press
.
UNIT
 LENGTH
INCH
mm
Use
Press
.
UNIT
 TEMP.
C
Use
perature.
Press
F
and switch on the sub power.
to select the display (menu) language.
to select the measurement unit for length.
to select to the measurement unit for tem-
3
.
Maintenance and
Adjustment
Description
This sets the language and units of measurement displayed on the display screen of the operation panel.
Default Setting
4
[MENU LANGUAGE]: ENGLISH
[LENGTH UNIT]: mm
[TEMP. UNIT]: °C
Feature
Reference
Returning All Settings to Their Initial Values
Procedure
5
What to Do If
 MENU
SUB MENU
Press
Press
.
several times.
MENU
 SUB
FACTORY DEFAULT
Press
Press
Press
.
several times.
to execute.
Description
This menu returns all settings to the same as their factory defaults. However, the settings for [LANGUAGE], [LENGTH UNIT],
and [TEMP. UNIT] are not returned to the factory defaults.
6
Specifications
86
4-7 Changing the Ink-drying Method
1
Switching Off the Print Heater and Dryer
 FUNCTION
HEATER CONFIG
Press
Press
.
several times.
CONFIG
 HEATER
DRYER
34 C
Press
Use
(dryer).
.
Press
Use
Press
.
Press
to go back to the original screen.
OFF
Current preset temperature
 W1200mm
Operation
 DRYER
35 C
to select [PRINT] (print heater) or [DRYER]
2
Current temperature
of the dryer
Introduction
Procedure
to select “OFF.”
to enable the setting.
3
SETUP SHEET
This menu is used to make the temperature settings for the print heater and dryer, and you can also use it to turn these off.
When set to "OFF," the print heater and dryer do not operate at all.
Note, however, that you can also make this setting on the computer. When you have made the setting on the computer, the
computer's setting is used and the printer's setting is ignored.
4
Default Setting
Maintenance and
Adjustment
Description
Determining How the Media Heating System Operates
Feature
Reference
[PRINT] (print heater) : 35°C (94°F)
[DRYER] (dryer) : 40°C (104°F)
Procedure
5
Press
Press
.
several times.
MENU
 HEATER
PREHEATING
Press
Press
.
.
 PREHEATING
30 C
MENU
Press
Use
Press
.
 W1200mm
Press
to go back to the original screen.
What to Do If
 MENU
HEATER MENU
6
to make the setting.
to enable the setting.
Specifications
SETUP SHEET
87
4-7 Changing the Ink-drying Method
1
Description
Introduction
This feature controls the temperature of the media heating system automatically when
is dark.
"MENU" performs heating to the preset temperature at all times, without lowering the temperature when
"30°C" lowers the temperature of the media heating system to a fixed temperature (30°C) when
is dark.
"OFF" switches off the media heating system when
is dark.
is dark.
Default Setting
[PREHEATING]: 30°C
2
Operation
Drying the Trailing Edge of the Printing Area on the Dryer
Procedure
3
Maintenance and
Adjustment
 MENU
HEATER MENU
Press
Press
.
several times.
FOR DRY
 FEED
DISABLE
ENABLE
Press
Use
Press
twice.
 W1200mm
Press
to go back to the original screen.
to select "ENABLE."
to enable the setting.
SETUP SHEET
4
Description
Feature
Reference
When this menu item is set to "ENABLE," additional media feed is performed until the trailing edge of the printing area is
positioned directly on the dryer.
The margin between the print-end position and the next print-start position is set to a value of 100 millimeters.
When a margin setting of less than 100 millimeters has been made on the computer, that setting is ignored and a margin
value of 100 millimeters is used.
However, when a margin setting of greater than 100 millimeters has been made on the computer, the computer's setting is
used for the margin value.
When this is set to "DISABLE," media feed stops simultaneously when printing ends. This means that the trailing edge of the
printing area is not fed to the dryer unless you continue with a subsequent printing operation.
5
Default Setting
What to Do If
[FEED FOR DRY]: DISABLE
6
Specifications
88
4-8 Making Various Adjustments for Cutting
1
Making the Cutting Conditions Set on the Machine Take Precedence
Introduction
Procedure
Press
Press
.
.
MENU
 CUTTING
CUTTING PRIOR
Press
Press
.
several times.
PRIOR
 CUTTING
COMMAND MENU
Press
Use
Press
.
 W1200mm
Press
to go back to the original screen.
2
 MENU
CUTTING MENU
Operation
to select "MENU."
to enable the setting.
SETUP SHEET
3
Description
Default Setting
[CUTTING PRIOR]: COMMAND
Maintenance and
Adjustment
You can also make the settings for the cutting conditions using the computer. By default, the settings made with the computer
take priority. To make the cutting conditions set on the machine take priority, either turn off the settings of the computer or
make the setting described above.
4
Procedure
Press
Press
.
several times.
CONFIG
 CUT
FORCE
Press
Use
set.
.
 FORCE
50 gf
Press
Use
Press
.
Press
to choose the cutting condition you want to
What to Do If
 W1200mm
60 gf
5
 FUNCTION
CUT CONFIG
Feature
Reference
Fine-tuning the Cutting Conditions
to enter the value.
to enable the setting.
to go back to the original screen.
6
SETUP SHEET
Specifications
89
4-8 Making Various Adjustments for Cutting
1
Description
Introduction
This enables you to check and verify the settings for the cutting conditions using cutting-test results.
 P. 46, "Performing a Cutting Test"
2
[FORCE]: This sets the force (pressure) of the blade.
[SPEED]: This sets the speed of cutting.
[OFFSET]: This makes the blade-offset setting for the blade. Enter the listed offset value for the blade. (The offset value for
the included blade is 0.25 mm.)
[UP-SPEED]: This sets the blade's up speed during cutting (the speed at which the blade travels when it moves to the next
cutting line after cutting one cutting line). If the media comes loose during no-load feed and the blade damages the surface
of the media, reduce the speed.
Operation
Evaluating the Results of a Cutting Test
 Check the shape of the test pattern.
The cut shape is distorted.
Reduce the cutting speed.
3

Peel off circle 1.
Rectangle 2 also peels off.
Circle 1
Maintenance and
Adjustment
Increase the blade force.
Some uncut areas remain.
Reduce the cutting speed.
Rectangle 2
4
 Peel off rectangle 2.
Feature
Reference
The blade should leave faint traces on the backing paper.
The blade trace is indistinct.
Increase the blade force.
The blade trace is too deep and cuts into the backing paper.
Reduce the blade force.

5
Check the shape of rectangle 2.
A. The shape is correct.
B. The corners are rounded.
What to Do If
Increase the amount of blade offset.
C. The corners have "horns."
Reduce the amount of blade offset.
A
6
Specifications
90
B
C
4-8 Making Various Adjustments for Cutting
Introduction
Min. 0 mm
1
Accurately Adjusting the Cutting-in Amount
Operation
Amount of blade
extension
2
When you want to perform accurate and fine adjustment
of the cutting-in amount, such as when cutting media
with thin backing paper, you can obtain good results by
adjusting the tip of the blade.
Turn the cap portion of the blade holder to adjust the
amount of blade extension. Each indicator tick corresponds to 0.1 millimeters, and adjustment for 0.5 millimeters can be made by rotating the cap one full turn.
Note that making the amount of blade extension too
small may cause the end of the cap for the blade holder
to touch and damage the printed surface. It's important to
be especially careful about this when you're using media
that has poor ink-adhesion properties.
Max. 2.5 mm
Rough Estimate for the Amount of Blade Extension
Use the following dimension as a rough estimate for setting the amount of blade extension.
3
Half of the
backing paper
Amount of blade extension
is approximately equal to
the cutting-in amount.
5
Procedure
Feature
Reference
Preventing Pulling of the Media with Undue Force When Performing Cutting Only
Press
Press
.
.
MENU
 CUTTING
PREFEED
Press
Press
.
 PREFEED
DISABLE
Press
Use
Press
.
to select "ENABLE."
to enable the setting.
Press
to go back to the original screen.
ENABLE
What to Do If
 MENU
CUTTING MENU
several times.
6
Specifications
 W1200mm
Maintenance and
Blade
Blade holder
4
Backing paper
portion
Adjustment
Thickness of the
Amount of blade Thickness of the
=
+ backing paper
material portion
extension
2
Material
portion
SETUP SHEET
91
4-8 Making Various Adjustments for Cutting
1
Description
Introduction
When you're performing cutting only, it may be convenient to set this feature to "ENABLE." This feeds out media according to
the size of the data sent from the computer before performing cutting. This makes it unnecessary to turn the media flanges
by hand to feed out media every time you perform cutting. Note, however, that this feeds out media even when you're
performing printing only, so set it to "DISABLE" when not needed.
Default Setting
[PREFEED]: DISABLE
2
Operation
Correcting Misalignment of the Printing and Cutting Positions
Procedure
1. Check the setting for the [AUTO ENV. MATCH] menu item.
3
Make sure the [AUTO ENV. MATCH] menu item is set to "ENABLE."
 P. 84, "Executing Environment Matching Automatically"
Maintenance and
Adjustment
2. Execute the [ADJUST BI-DIR] menu item.
 Load the media.
 P. 32, "Loading Media"
 P. 82, "How to Load Sheet Media"
 Perform bidirectional adjustment.
4
 P. 73, "Correcting for Misalignment in Bidirectional Printing"
 P. 74, "Correcting for Misalignment in Bidirectional Printing More Precisely"
Feature
Reference
3. Print a test pattern and cut it.
5
What to Do If
 MENU
CUTTING MENU
Press
Press
.
.
MENU
 CUTTING
PRINT - CUT ADJ.
Press
.
- CUT ADJ.
 PRINT
TEST PRINT
Press
Press
.
.
The test pattern is printed at three locations: at the two edges and in the center.
When adjustment is needed, go on to the steps below.
6
Specifications
92
4-8 Making Various Adjustments for Cutting
1
Cutting
position
Printing
position
Printing
position
Cutting position and printing
position are misaligned.
Introduction
Cutting
position
Cutting position and printing position are aligned.
2
Operation
4. Print and cut a test pattern for setting the correction values.
PRINT - CUT ADJ.
TEST PRINT 2
Press
Press
.
to execute.
Cutting line
Correction-value scale
4
Scan direction
The point where the cutting line
intersects the correction-value
scale is the correction value. In this
figure, the value is "-0.3." Use the
same method to read the value on
the [FEED] side.
5
Press
.
0.30
 FS :-: 0.00
Press
Use
tion).
Use
direction).
Press
.
Press
.
- 0.30mm
- 0.20mm
to set the correction value for [F] (the feed directo set the correction value for [S] (the scanning
6
to enable the setting.
Specifications
- CUT ADJ.
 PRINT
SETTING
What to Do If
6. Enter the correction value you read.
- CUT ADJ.
 PRINT
SETTING
Feature
Cutting line
Reference
Check the value on
the [FEED] side.
Maintenance and
Check the value on
the [SCAN] side.
Adjustment
Test pattern
3
5. From the test pattern, read the value at the location.
93
4-8 Making Various Adjustments for Cutting
1
7. Check the results of adjustment.
Introduction
PRINT - CUT ADJ.
TEST PRINT
Press
Press
.
to execute.
Cutting position
If the printing and cutting lines are aligned, adjustment
is complete.
If further adjustment is needed, go back to step
and
fine-tune the adjustment.
2
Operation
Printing position
Cutting position and printing
position are aligned.
3
Description
Maintenance and
Adjustment
You perform this when printing followed immediately by cutting yields positioning for printing and cutting that is slightly
misaligned. You print alignment marks, perform detection of the printed marks, and correct the discrepancy.
Subtle misalignment between the printing and cutting positions may occur due to the thickness of the media or the head
height. We recommend making correction to match the media you're using.
Default Setting
[F] (feed direction): 0.00 mm
[S] (scanning direction): 0.00 mm
4
Feature
Reference
5
What to Do If
6
Specifications
94
4-9 Performing Printing and Cutting Separately
1
To Perform Printing and Cutting Separately
Introduction
When you remove printed media and then reload it and perform cutting, you carry out alignment to prevent misalignment
of the printing results and the cut lines. You do this at times such as when, for example, you perform lamination or other
processing after printing, then reload the media and perform cutting. At such times, you perform printing with crop marks.
You can perform automatic alignment with detection of the printed crop marks when you perform cutting.
2
Printing with Crop Marks
Operation
Use your software RIP to make the settings for printing crop marks. For information on how to make the setting, refer to the
documentation for the software RIP you're using. Alignment marks and symbols drawn using a graphics program cannot
be used as crop marks.
Crop Mark
(Align point 2)
Crop Mark
(Align point 1)
Crop Mark
(Base point)
The crop marks are printed as shown
in the figure.
3
Crop Mark
(Align point 3)
4
5
Pinch rollers
What to Do If
Where to cut the media off
1.5 mm (about 0.06 in.)
90 mm (3.5 in.) or
more
Feature
Reference
When you are printing with crop marks, set a margin of at least 90 mm (3.5 in.) before the next print-start position.
You can set the margin value with the software RIP you're using. For information on how to make the setting, refer to the
documentation for the software RIP you're using.
Crop marks
Maintenance and
Adjustment
Media Sizes Allowing Automatic Crop Mark Detection
1.5 mm (about 0.06 in.)
6
22.5 mm (0.89 in.)
The actual size where
output is possible
22.5 mm (0.89 in.)
Specifications
80 mm (3.2 in.) or more
95
4-9 Performing Printing and Cutting Separately
1
Aligning Automatically and Cutting
Introduction
When you make the setting for reading crop marks when sending cutting data from the computer, alignment is performed
with the presence or absence of crop marks determined automatically.
For information on how to make the setting, refer to the documentation for the software RIP you're using.
Procedure

Load the media.
2
Operation
3
Crop marks
Blade protection
Maintenance and
Adjustment
Angled no more than 5 degrees.
Otherwise alignment becomes impossible.
5 degrees
or more
4
Feature
Reference
5 degrees
or more
 Send the cutting data.
Alignment is performed automatically, then cutting starts.
5
If Automatic Alignment Cannot Be Performed
What to Do If
CROPMARK ERROR
NOT FOUND
If the machine fails to detect the crop marks, the screen shown in the figure appears
and operation stops.
If this happens, press
, then take action as follows.
 Reload the media, then send the data again.
 If this does not resolve the problem, then perform alignment manually.
 P. 97, "Aligning Manually and Cutting"
6
Specifications
If the crop marks cannot be detected easily because of the effects of media warping or the like, then perform alignment
manually. When you want to perform automatic alignment with lengthy media, we recommend performing output with the
data separated into sizes that are as short as possible. With large sizes, error due to warping and the like increases, making
smooth detection impossible.
96
4-9 Performing Printing and Cutting Separately
 Press
Press
.
Introduction
 CANCEL CROPMARK
DETECTION?
1
To Quit Detection and Start Cutting
Crop-mark detection stops. Depending on the content of the data, some time may
pass before detection actually stops.
.
This stops detection and starts cutting.
2
in step
, resuming detection or canceling output is also possible.
Note: After pressing
 P. 68, "Pausing or Canceling Output"
Operation
Aligning Manually and Cutting
Depending on the type of media, it may not be possible to detect crop marks automatically. When crop marks cannot be
detected automatically, you perform alignment manually.
3
Procedure
Use
to align the
center of the blade with the location shown
in the figure.
Maintenance and

Adjustment
1. Set the base point.
4
.
.
5
Press
Press
What to Do If
2. Set the align points.

Feature
Reference
 W1100mm
B
Use
to align the
center of the blade with the location shown
in the figure.
6
Specifications
97
4-9 Performing Printing and Cutting Separately
1
POINT
 BASE
ALIGN POINT 1
Press
Press
.
.
Press
Press
.
to go back to the original screen.
Introduction
The number of the align point you set is automatically determined.
mm
 W1100
B1
This indicates that the base point and
align point 1 have been set.
2
 Repeat steps through to specify other align points as required.
 Send the cutting data and perform cutting.
Operation
About Align Points
The numbers for align points are determined with reference to the location of the base point. You cannot set an align point
unless you specify a base point. Redoing the setting for the base point clears any align points that have been set.
3
Correcting Misalignment for Printing and Cutting When Using Crop Marks
Maintenance and
Adjustment
Procedure
1. Check the setting for the [AUTO ENV. MATCH] menu item.
Make sure the [AUTO ENV. MATCH] menu item is set to "ENABLE."
 P. 84, "Executing Environment Matching Automatically"
4
Feature
Reference
2. Execute the [ADJUST BI-DIR] menu item.
 Load the media.
 P. 32, "Loading Media"
 P. 82, "How to Load Sheet Media"
 Perform bidirectional adjustment.
5
 P. 73, "Correcting for Misalignment in Bidirectional Printing"
 P. 74, "Correcting for Misalignment in Bidirectional Printing More Precisely"
What to Do If
6
Specifications
98
4-9 Performing Printing and Cutting Separately
1
3. Print a test pattern and cut it.
.
.
MENU
 CUTTING
CROP - CUT ADJ.
Press
Press
.
.
- CUT ADJ.
 CROP
TEST PRINT
Press
Press
.
.
Introduction
Press
Press
2
 MENU
CUTTING MENU
Cutting
position
Printing
position
Printing
position
Cutting position and printing
position are aligned.
3
Cutting position and printing
position are misaligned.
Operation
Cutting
position
4. Print and cut a test pattern for adjustment.
Press
Press
.
to execute.
4
CROP - CUT ADJ.
TEST PRINT 2
Check the value on
the [SCAN] side.
Cutting line
5
Correction-value scale
What to Do If
Check the value on
the [FEED] side.
Feature
Reference
5. From the test pattern, read the correction value at the location.
Test pattern
Maintenance and
Adjustment
When adjustment is needed, go on to the steps below.
Scan direction
Cutting line
The point where the cutting line
intersects the correction-value
scale is the correction value. In this
figure, the value is "-0.3." Use the
same method to read the value on
the [FEED] side.
6
Specifications
99
4-9 Performing Printing and Cutting Separately
1
6. Enter the correction value you read.
Introduction
- CUT ADJ.
 CROP
SETTING
Press
.
0.30
 FS :-: 0.00
Press
Use
tion).
Use
direction).
Press
.
to enable the setting.
Press
.
- 0.30mm
- 0.20mm
2
Operation
- CUT ADJ.
 CROP
SETTING
to set the correction value for [F] (the feed directo set the correction value for [S] (the scanning
7. Check the results of adjustment.
3
CROP - CUT ADJ.
TEST PRINT
Press
Press
.
to execute.
Maintenance and
Adjustment
Cutting position
If the printing and cutting lines are aligned, adjustment is
complete.
If further adjustment is needed, go back to step and finetune the adjustment.
Printing position
Cutting position and printing
position are aligned.
4
Feature
Reference
Description
Depending on the composition of the media, the positioning of printing and cutting may be misaligned even when you're
using crop marks. Make corrections for misaligned printing and cutting for the media you're using.
Default Setting
5
[F] (feed direction): 0.00 mm
[S] (scanning direction): 0.00 mm
What to Do If
6
Specifications
100
4-10 Making the Network Settings
1
Setting the IP Address, Subnet Mask, Etc.
Press
Press
.
several times.
INFO.
 SYSTEM
NETWORK
Press
Press
.
.
 NETWORK
IP ADDRESS
Press
Use
to make.
.
 IP000.ADDRESSS
000. 000. 000
Press
Use
twice.
 IP192.ADDRESS
000. 000. 000
Press
.
 IP192.ADDRESS
168. 000. 003
Repeat  and  to set all the address numbers.
When you have finished making the setting, press
 W1200mm
Press
2
 MENU
SYSTEM INFO.
Introduction
Procedure
Operation
to choose the item whose setting you want
to select the address number.
3
to go back to the original screen.
SETUP SHEET
4
Description
Maintenance and
Adjustment
.
[IP ADDRESS]: IP address
[SUBNET MASK]: Subnet mask
[GATEWAY ADDR.]: Gateway address
Feature
Reference
Make sure the machine is connected to the network by an Ethernet cable.
For detailed information about the settings, consult your network administrator.
5
What to Do If
6
Specifications
101
4-11 Viewing Information about the Media and the System
1
Displaying the Amount of Media Remaining
Introduction
Procedure
2
Operation
 MENU
SHEET REMAIN
Press
Press
.
REMAIN
 SHEET
SET LENGTH
Press
Press
.
.

Press
Use
Press
.
Press
to go back to the original screen.
SET LENGTH
0.0 m
25.0 m
 W1200 mm
L 25.0 m
twice.
to set the amount of media remaining.
to enable the setting.
This display is updated.
SETUP SHEET
3
L 25.0 m
Maintenance and
Adjustment
If setup has not been performed,
the set value flashes.
Description
4
Feature
Reference
You can display how much of the media in use is left. Once you set the amount of media remaining, the amount remaining is
displayed at the top menu until it reaches zero. If you cancel the setup such as by removing the media or raising the loading
lever, the amount remaining at that time flashes on the screen. The amount of media remaining is not updated automatically
when you change the media. Redo the setting whenever you change the media.
You can also make the setting display this menu automatically whenever you change the media. See the next section, "Verifying the Setting for the Amount Remaining Every Time the Media Is Changed."
Note: The remaining amount that is displayed is only an estimate, and its accuracy is not assured.
Verifying the Setting for the Amount Remaining Every Time the Media Is Changed
Procedure
5
What to Do If
 MENU
SHEET REMAIN
Press
Press
.
.
REMAIN
 SHHET
AUTO DISPLAY
Press
Press
.
twice.

Press
Use
Press
.
Press
to go back to the original screen.
AUTO DISPLAY
DISABLE
ENABLE
6
 W1200mm
SETUP SHEET
Specifications
102
to select "ENABLE."
to enable the setting.
4-11 Viewing Information about the Media and the System
1
Description
Introduction
Setting this to "ENABLE" automatically displays [SHEET REMAIN] whenever you change the media and finish setup.
This makes it impossible to go on to the next operation unless you redo the setting for the amount remaining. This can be
useful for keeping you from forgetting to redo the setting when you change the media.
When you set this to "ENABLE," however, be sure also to set the [EDGE DETECTION] menu item to "ENABLE." When [EDGE
DETECTION] is set to "DISABLE," then [SHEET REMAIN] is not displayed automatically, regardless of the setting for [AUTO
DISPLAY].
 P. 78, "Using Transparent Media"
Default Setting
2
[AUTO DISPLAY]: DISABLE
Operation
Printing the Amount of Remaining Media
Procedure
.
REMAIN
 SHHET
PRINT MEMO
Press
Press
.
to perform printing.
 W1200mm
Press
to go back to the original screen.
twice.
Adjustment
SETUP SHEET
Maintenance and
Press
Press
3
 MENU
SHEET REMAIN
4
Description
Feature
Reference
5
This prints the amount of media remaining that is displayed at the top menu. You use this when you want to make a record
of the remaining length of the media now in use. Printing the amount of media remaining before you change the media
enables you to refer to the printed record and use the value to make the setting for the remaining amount the next time
you use the media.
Note, however, that continuing by performing the next output starts the output on top of the portion where the amount of
remaining media is printed. After printing the amount remaining, then before you perform the next output operation, we
recommend cutting off the media.
 P. 38, "Cutting Off the Media"
What to Do If
6
Specifications
103
4-11 Viewing Information about the Media and the System
1
Viewing the Serial Number, Firmware Version, and Other Information
Introduction
Procedure
2
Operation
 MENU
SYSTEM INFO.
Press
Press
.
several times.
INFO.
 SYSTEM
SERIAL NO.
Press
Use
.
NO.
 SERIAL
ZS00001
Press
.
 W1200mm
Press
to go back to the original screen.
to choose the information you want to view.
SETUP SHEET
3
Description
Maintenance and
Adjustment
You can view the following information.
[MODEL]: Model name
[SERIAL NO.]: Serial number
[INK]: Ink type
[FIRMWARE]: Firmware version
Viewing the Network Settings
4
Feature
Reference
Procedure
5
What to Do If
 MENU
SYSTEM INFO.
Press
Press
.
several times.
INFO.
 SYSTEM
NETWORK
Press
Press
.
.
 NETWORK
IP ADDRESS
Press
Use
.
 IP192.ADDRESS
168. 000. 003
Press
.
 W1200mm
Press
to go back to the original screen.
SETUP SHEET
6
Specifications
104
to choose the information you want to view.
4-11 Viewing Information about the Media and the System
1
Description
Introduction
You can view the following information.
[IP ADDRESS]: IP address
[SUBNET MASK]: Subnet mask
[GATEWAY ADDR.]: Gateway address
[MAC ADDRESS]: MAC address
2
Printing a System Report
Operation
Procedure
 Press
Press
.
several times.
 W1200mm
Press
to go back to the original screen.
SETUP SHEET
Description
4
This prints system information, including a list of setting values.
Maintenance and
.
several times.
to start printing.
Adjustment
Press
Press
Press
3
MENU
 SUB
SYSTEM REPORT
Feature
Reference
5
What to Do If
6
Specifications
105
4-12 Performing Maintenance
1
Draining Ink and Performing Internal Washing
Introduction
Procedure
2
Operation
 MENU
SUB MENU
Press
Press
.
several times.
MENU
 SUB
INK CONTROL
Press
Press
.
twice.
CONTROL
 INK
HEAD WASH
Press
Press
Press
.
twice.
to execute.
Description
3
This drains the ink inside the printer and washes the interior using cleaning cartridges as a preliminary for moving the printer
or conducting maintenance. This operation requires four unused cleaning cartridges. The screen displays information such
as instructions to insert and remove cartridges. Follow these instructions to carry out the procedure. After finishing washing,
the sub power is automatically switched off.
You do not need to carry this out as part of your daily maintenance activities.
Maintenance and
Adjustment
Draining Ink Remaining Inside the Machine
Procedure
4
Feature
Reference
 MENU
SUB MENU
Press
Press
.
several times.
MENU
 SUB
INK CONTROL
Press
Press
.
twice.
CONTROL
 INK
PUMP UP
Press
Press
Press
.
.
to execute.
5
Description
What to Do If
This removes ink inside the printer as a preliminary procedure for performing maintenance. The screen displays information
such as instructions to insert and remove cartridges. Follow these instructions to carry out the procedure. After finishing the
procedure, the sub power is automatically switched off.
You do not need to carry this out as part of your daily maintenance activities.
6
Specifications
106
107
4-13 Menu List
1
Main Menu
Introduction
Press
To the [CUTTING MENU] menu
 P. 71
MENU
PRESET
To the [NAME] menu
PRESET
LOAD
To the [NAME8] menu
LOAD
NAME1
2
Operation
LOAD
NAME2
LOAD
NAME3
LOAD
NAME4
3
LOAD
NAME5
Maintenance and
Adjustment
LOAD
NAME6
LOAD
NAME7
LOAD
NAME8
4
To the [NAME1] menu
To the [NAME8] menu
Feature
Reference
 P. 70
SAVE
NAME1
PRESET
SAVE
SAVE
NAME2
SAVE
NAME3
5
SAVE
NAME4
What to Do If
SAVE
NAME5
SAVE
NAME6
SAVE
NAME7
6
Specifications
SAVE
NAME8
To the [NAME1] menu
Continue
108
Continue
Continue
4-13 Menu List
Continue
Continue
Continue
1
To the [NAME8] menu
 P. 71
PRESET
NAME
NAME
_
NAME
NAME2
NAME
_
NAME
NAME3
NAME
_
NAME
NAME4
NAME
_
NAME
NAME5
NAME
_
NAME
NAME6
NAME
_
NAME
NAME7
NAME
_
NAME
NAME8
NAME
_
Introduction
NAME
NAME1
To the [LOAD] menu
2
Operation
3
 P. 73
To the [NAME1] menu
ADJUST BI-DIR
TEST PRINT
ADJUST BI-DIR
SIMPLE SETTING
SIMPLE SETTING
0
0
ADJUST BI-DIR
DETAIL SETTING
DETAIL SETTING
TEST PRINT
Maintenance and
MENU
ADJUST BI-DIR
Adjustment
 P. 73, 74
To the [DETAIL SETTING] menu
To the [SETTING No.4] menu
4
 P. 74
H2
0
H3
0
H4
0
DETAIL SETTING
SETTING NO.2
H1
0
H2
0
H3
0
H4
0
DETAIL SETTING
SETTING NO.3
H1
0
H2
0
H3
0
H4
0
DETAIL SETTING
SETTING NO.4
H1
0
H2
0
H3
0
H4
0
5
H1
0
Feature
DETAIL SETTING
SETTING NO.1
Reference
To the
[TEST PRINT] menu
 P. 76
MENU
CALIBRATION
What to Do If
To the [TEST PRINT] menu
To the [SETTING] menu
CALIBRATION
TEST PRINT
CALIBRATION
SETTING
SETTING
0.00%
0.00%
To the [TEST PRINT] menu
6
Continue
Specifications
109
4-13 Menu List
Continue
1
 P. 72
Introduction
MENU
HEAD HEIGHT
HEAD HEIGHT
HIGH
HIGH
(*1)
 P. 78
To the [MAINTENANCE] menu
MENU
SUB MENU
 P. 78
2
 P. 79
Operation
 P. 79
 P. 80
 P. 86
SUB MENU
EDGE DETECTION
EDGE DETECTION
ENABLE
ENABLE
SUB MENU
SCAN INTERVAL
SCAN INTERVAL
OFF
OFF
SUB MENU
VACUUM POWER
VACUUM POWER
AUTO
AUTO
SUB MENU
FULL WIDTH S
FULL WIDTH S
FULL
FULL
SUB MENU
PERIODIC CL.
PERIODIC CL.
NONE
NONE
SUB MENU
FACTORY DEFAULT
3
To the [SETTING] menu
 P. 85
Maintenance and
Adjustment
SUB MENU
SLEEP
 P. 85
SLEEP
INTERVAL
INTERVAL
30min
30min
SLEEP
SETTING
SETTING
ENABLE
ENABLE
To the [INTERVAL] menu
 P. 105
SUB MENU
SYSTEM REPORT
To the [HEAD WASH] menu
4
 P. 84
SUB MENU
INK CONTROL
Feature
Reference
 P. 106
INK CONTROL
EMPTY MODE
EMPTY MODE
STOP
STOP
INK CONTROL
PUMP UP
 P. 106
INK CONTROL
HEAD WASH
To the [EMPTY MODE] menu
To the [DRAIN BOTTLE] menu
 P. 54
MAINTENANCE
CLEANING
To the [EDGE DETECTION]
menu
MAINTENANCE
REPLACE WIPER
5
SUB MENU
MAINTENANCE
 P. 58
What to Do If
MAINTENANCE
REPLACE KNIFE
MAINTENANCE
DRAIN BOTTLE
To the [CLEANING] menu
6
Continue
Specifications
(*1) This is displayed only on the 54-inch model.
110
4-13 Menu List
Continue
1
 P. 104
To the [NETWORK] menu
 P. 104
 P. 104
SYSTEM INFO.
SERIAL NO.
SERIAL NO .
ZS00001
SYSTEM INFO.
INK
INK
E-SOL Max 4COLOR
SYSTEM INFO.
FIRMWARE
FIRMWARE
Ver.1.00
SYSTEM INFO.
NETWORK
NETWORK
IP ADDRESS
Operation
MODEL
VP-540
2
 P. 104
SYSTEM INFO.
MODEL
Introduction
MENU
SYSTEM INFO.
To the [MAC ADDRESS] menu
 P. 104
IP ADDRESS
2 5 5. 2 5 5. 2 5 5. 2 5 5
IP ADDRESS
2 5 5. 2 5 5. 2 5 5. 2 5 5
To the [MODEL] menu
SUBNET MASK
2 5 5. 2 5 5. 2 5 5. 2 5 5
 P. 104
NETWORK
GATEWAY ADDRESS
GATEWAY ADDRESS
2 5 5. 2 5 5. 2 5 5. 2 5 5
GATEWAY ADDRESS
2 5 5. 2 5 5. 2 5 5. 2 5 5
NETWORK
MAC ADDRESS
MAC ADDRESS
000086148C5F
 P. 104
 P. 88
To the [PREHEATING] menu
MENU
HEATER MENU
 P. 87
To the [IP ADDRESS] menu
HEATER MENU
FEED FOR DRY
FEED FOR DRY
DISABLE
DISABLE
HEATER MENU
PREHEATING
PREHEATING
30 C
30 C
Maintenance and
SUBNET MASK
2 5 5. 2 5 5. 2 5 5. 2 5 5
Adjustment
NETWORK
SUBNET MASK
3
 P. 104
To the [FEED FOR DRY] menu
MENU
INK REMAINING
1
MENU
SHEET REMAIN
SHEET REMAIN
PRINT MEMO
2
3
4
To the [AUTO DISPLAY] menu
 P. 102
SHEET REMAIN
AUTO DISPLAY
AUTO DISPLAY
DISABLE
DISABLE
What to Do If
Continue
SET LENGTH
0.0 m
0.0 m
5
 P. 102
SHEET REMAIN
SET LENGTH
Feature
 P. 103
MEDIA CLAMP
SHORT
SHORT
Reference
 P. 43
MENU
MEDIA CLAMP
4
 P. 81
To the [PRINT MEMO] menu
6
Specifications
111
4-13 Menu List
Continue
1
To the [TEST PRINT 2] menu
To the [AUTO ENV. MATCH] menu
 P. 92
MENU
CUTTING MENU
CUTTING MENU
PRINT-CUT ADJ.
PRINT-CUT ADJ.
TEST PRINT
Introduction
To the
[PRESET] menu
PRINT-CUT ADJ.
SETTING
F : +0.00
S : +0.00
0.00m
0.00m
PRINT-CUT ADJ.
TEST PRINT 2
To the [TEST PRINT] menu
To the [TEST PRINT 2] menu
 P. 99
2
CUTTING MENU
CROP-CUT ADJ.
CROP-CUT ADJ.
TEST PRINT
Operation
CROP-CUT ADJ.
SETTING
F : +0.00
S : +0.00
0.00m
0.00m
CROP-CUT ADJ.
TEST PRINT2
To the [TEST PRINT] menu
To the [SCAN SETTING] menu
 P. 77
CUTTING MENU
CALIBRATION
FEED SETTING
0.00%
0.00%
CALIBRATION
SCAN SETTING
SCAN SETTING
0.00%
0.00%
3
CALIBRATION
FEED SETTING
Maintenance and
Adjustment
To the [FEED SETTING] menu
 P. 91
 P. 89
4
 P. 84
CUTTING MENU
PREFEED
PREFEED
DISABLE
CUTTING MENU
CUTTING PRIOR
CUTTING PRIOR
COMMAND COMMAND
CUTTING MENU
AUTO ENV. MATCH
AUTO ENV. MATCH
ENABLE
ENABLE
To the [PRINT-CUT ADJ .] menu
Feature
Reference
Language and Unit Menu
While holding down
, switch on the sub power.
5
What to Do If
 P. 86
 P. 86
 P. 86
6
Specifications
112
MENU LANGUAGE
ENGLISH
LENGTH UNIT
mm
mm
TEMP UNIT
C
C
DISABLE
4-13 Menu List
1
Function Menu
Introduction
Press
 P. 69
BASE POINT
ALIGN POINT 1
(*2)
To the [POWERFUL CL.] menu
FUNCTION
CLEANING
2
 P. 42
To the [CUT CONFIG] menu
FUNCTION
BASE POINT
(*2)
CLEANING
TEST PRINT
Operation
CLEANING
NORMAL CL.
CLEANING
MEDIUM CL.
3
CLEANING
POWERFUL CL.
To the [TEST PRINT] menu
HEATER CONFIG
DRYER
40 C
DRYER
40 C
40 C
FUNCTION
CUT CONFIG
CUT CONFIG
TEST CUT
(*2)
FORCE
50gf
50gf
CUT CONFIG
SPEED
SPEED
30cm/s
30cm/s
CUT CONFIG
OFFSET
OFFSET
0.250mm
0.250mm
CUT CONFIG
UP-SPEED
UP-SPEED
30cm/s
30cm/s
5
CUT CONFIG
FORCE
Feature
 P. 89
30 C
Reference
 P. 89
PRINT
30 C
To the [PRINT] menu
To the [UP-SPEED] menu
To the [BASE POINT] menu
 P. 47, 89
HEATER CONFIG
PRINT
35 C
4
 P. 46
To the [DRYER] menu
FUNCTION
HEATER CONFIG
Maintenance and
 P. 39
FUNCTION
SHEET CUT
(*2)
Adjustment
 P. 38
What to Do If
To the [TEST CUT] menu
(*2) This is not displayed when no media is loaded (that is, when
is dark).
6
Specifications
113
114
1
Introduction
2
Operation
3
Chapter 5
What to Do If
Attractive Printing or Cutting Is Impossible......................................................... 117
The Media Jams................................................................................................. 119
Media Wrinkles or Shrinks, or Feed Is Unstable.................................................120
Maintenance and
Adjustment
The Machine Doesn't Run.................................................................................. 116
The Print Heads Stopped Moving.......................................................................121
4
If a Message Appears.........................................................................................122
If an Error Message Appears..............................................................................123
Feature
Reference
5
What to Do If
6
Specifications
115
5-1 The Machine Doesn't Run
1
The Printer Unit Doesn't Run
Introduction
Switch on the printer's main power, then press the sub power
switch and make sure the sub power switch lights up.
device on the network, that the port setting for the software
RIP specifies the IP address set on the machine, that the settings
have no typing errors, and for other such problems.
 Setup Guide
 P. 104, "Viewing the Network Settings"
Is
Did the software RIP end abnormally?
Is the power switched on?
illuminated?
Output is not performed when
Lower the loading lever.
is not illuminated.
Make sure the software RIP is running correctly, then switch the
sub power switch off and back on.
Is the front cover open?
2
Close the front cover.
The Media Heating System Doesn't Warm Up
Operation
Is the top menu displayed?
W1200mm
Top menu
If the top menu isn't displayed,
output doesn't start even when
data is sent from the computer.
To go to the top menu, press
, then press
.
 P. 41, "Getting Ready to Receive Data from a Computer"
3
Is
illuminated?
When
Maintenance and
Adjustment
.
lights up, operation is paused. To resume, press
goes dark and outputting resumes.
Has ink run out?
4
When printing data is sent while
the screen shown in the figure is
displayed, a message appears and
a warning beep sounds. At the same time, operation pauses.
When the ink cartridge is replaced with a new one, printing or
cutting starts.
1
2
3
4
 P. 44, "If Ink Runs Out"
Feature
Reference
 P. 84, "Determining What Happens When Ink Runs Out"
Is a message displayed on the screen?
 P. 122, "If a Message Appears"
 P. 123, "If an Error Message Appears"
Is the cable connected?
Connect the cable securely.
5
What to Do If
Is the Link LED lighted?
If the Link LED for the Ethernet connector is not lighted, it means
that a correct connection to the network has not been made.
Make sure the network routing is suitable. Try connecting the
computer and the machine to the same hub, or connecting
them directly using a crossover cable. If this makes it possible to
perform output, it means the problem is in the network itself.
Are the network settings correct?
6
Specifications
If output is not possible even though the Link LED is lighted,
check to make sure the IP address and other such settings are
correct. The settings on both the machine and the computer
must be appropriate. Redo the settings, checking to ensure that
the IP address doesn’t conflict with the IP address for another
116
Is media loaded?
The media heating system does not warm up to the preset
temperature when
is dark (by default). Load media
and wait for the machine to warm up.
 P. 87, "Determining How the Media Heating System Operates"
Is the temperature of the room too low?
Use the machine in an environment where the temperature is
20 to 32°C (68 to 90°F).
5-2 Attractive Printing or Cutting Is Impossible
Do the print heads show dot drop-out?
Is the head height appropriate?
Have you carried out feed correction?
If the media is not loaded and set up correctly, media feed may
not be smooth, or printing may be adversely affected. Make sure
the media is loaded and set up correctly.
 P. 120, "Media Wrinkles or Shrinks, or Feed Is Unstable"
Are the settings for the [PRESET] menu item appropriate?
If the settings selected with the [PRESET] menu item are not suitable for the type of media, printing may be adversely affected.
Choose settings optimized to the media you're using.
 P. 70, "Saving Optimized Media Settings As Preset Values"
 P. 71, "Loading a Saved Preset"
Is the media wrinkled?
If the media is wrinkled and comes loose from the platen, colors
may be uneven or printing quality may suffer.
 P. 120, "Media Wrinkles or Shrinks, or Feed Is Unstable"
If the ink forms lumps or smudges, raise the temperature. Note,
however, that a temperature that is too high may degrade the
media or cause it to wrinkle.
 P. 39, "Settings for the Media Heating System"
Is the media sagging?
Is the temperature of the room too low?
When printing is paused, the coloring at the seam may be altered
when printing resumes. Avoid pausing printing. By default,
printing pauses when ink remaining inside the machine runs
out. Before you perform lengthy printing, check the amount of
ink remaining in the ink cartridges.
Printing may also pause when data is not sent from the computer
quickly enough. We recommend not performing any other tasks
with the computer while printing is in progress.
Is the printer installed in a level and stable location?
117
Specifications
Never install the machine in a location where it is tilted or where
it may wobble or experience vibration. Also make sure that the
print heads are not exposed to moving air. These factors may
lead to missing dots or reduced printing quality.
6
If attractive printing is impossible even when the media heating system is at a high temperature, try using a higher-quality
print mode. Depending on the media, smudging may occur
when using a high-quality print mode, and results may also vary
greatly depending on the settings of your software RIP (such as
the color-profile selection). Make settings suited to the media
Was printing paused partway through?
What to Do If
Is the print mode suitable?
Performing printing using sagging roll media makes uneven
colors more likely.
5
The media heating system may not warm up sufficiently when
the ambient temperature is less than 20°C (68°F). Also, even
when the media heating system reaches its preset temperatures,
adequate effectiveness may not be apparent if the media is
thoroughly chilled. Before printing, allow the media to come to
room temperature.
Feature
Is the print heater at a suitable temperature?
If you’re using a model that uses ECO-SOL MAX ink, then shake
new cartridges gently before you install them.
Reference
Precisely"
Did you shake the ink cartridges gently before installing them?
4
When you are performing bidirectional printing, use the [ADJUST
BI-DIR] menu item to carry out correction. The optimal adjustment value may vary, depending mainly on the thickness of
the media. Set or select an adjustment value that is suited to
the media.
 P. 73, "Correcting for Misalignment in Bidirectional Printing"
 P. 74, "Correcting for Misalignment in Bidirectional Printing More
Colors Are Unstable or Uneven
Maintenance and
Have you carried out bidirectional correction?
Adjustment
the Like"
3
Large misalignment in the amount of feed of the media may
result in printing that seems coarse or contains horizontal
stripes. Either make the setting on the computer to match the
type of media you're using, or make the setting for correction
on the printer.
 P. 76, "Performing Feed Correction to Alleviate Horizontal Bands and
Is the media loaded and set up correctly?
Operation
Model Only)"
Never install the machine in a location where it is tilted or where
it may wobble or experience vibration. Also make sure that the
print heads are not exposed to moving air. These factors may
lead to missing dots or reduced printing quality.
2
Printing when the [HEAD HEIGHT] menu item is set to "HIGH" is
coarser than when set to "LOW." Keep this set to "LOW" except
when changing it is necessary, such as when you're using thick
media.
 P. 72, "Adjusting Head Height to Match Media Thickness (54-inch
Is the printer installed in a level and stable location?
Introduction
Carry out a printing test and make sure no dot drop-out occurs.
If dot drop-out is present, perform head cleaning.
 P. 42, "Printing Tests and Cleaning"
 P. 53, "When Head Cleaning Is Not Effective"
you're using.
1
Printed Results Are Coarse or Contain Horizontal Stripes
5-2 Attractive Printing Is Impossible
1
Are the operating parameters set to appropriate
values?
Introduction
Depending on the settings for such menu items as [FULL WIDTH
S] and [PERIODIC CL.], uneven colors may occur. If the settings
have been changed, try restoring them to their default values.
 P. 79, "Speeding Up Output for Narrow Media"
 P. 80, "Preventing Soiling of the Media and Dot Drop-out During Printing”
Are the settings for the [PRESET] menu item appropriate?
2
Operation
If the settings selected with the [PRESET] menu item are not suitable for the type of media, printing may be adversely affected.
Choose settings optimized to the media you're using.
 P. 70, "Saving Optimized Media Settings As Preset Values"
 P. 71, "Loading a Saved Preset"
The Media Becomes Soiled When Printed
Do the print heads contact the media?
3
Maintenance and
Adjustment
The height of the print heads may be too low. Also, if the media
is not loaded and set up correctly, it may wrinkle or come loose
and strike the heads.
 P. 120, "Media Wrinkles or Shrinks, or Feed Is Unstable"
 P. 72, "Adjusting Head Height to Match Media Thickness (54-inch Model
Only)"
Are the print heads dirty?
4
Feature
Reference
The following may cause ink to drip on the media during printing.
 Buildup of fibrous dust (lint) around the heads.
 Ink transferred to the heads due to rubbing against the media.
If this happens, clean the heads using the cleaning kit. We recommend carrying out periodic head cleaning.
 P. 54, "Cleaning the Heads Using the Cleaning Kit"
Are the pinch rollers or the media clamps dirty?
Periodically clean them.
 P. 52, "Cleaning"
5
What to Do If
Cutting Is Misaligned or Skewed
Is the media loaded and set up correctly?
If the media is not loaded and set up correctly, or media feed is
not smooth, cutting may be adversely affected. Make sure the
media is loaded and set up correctly.
 P. 120, "Media Wrinkles or Shrinks, or Feed Is Unstable"
6
Are the settings for the cutting conditions appropriate?
Specifications
Misalignment or skewing may occur if the cutting speed is too
fast or the blade force is too high. Try changing the cutting conditions. With media having a strong adhesive layer, the adhesive
layer reattaches to itself immediately after cutting. However, if a
118
cutting test shows that the peeling of the media and the blade
traces on the backing paper are optimal, then the media is being
cut properly. Be careful not to make the blade force too high.
Is the length of output too long?
For printing followed immediately by cutting in particular, the
longer the page length (that is, the longer the distance the media
is returned after printing), the greater is the chance of misalignment occurring. It is a good idea to keep the size of each single
page to the minimum necessary.
Are you using media that exhibits large expansion
and contraction?
When you're performing printing followed immediately by cutting, misalignment occurs if the media expands or contracts.
If this happens, try performing printing with crop marks, then
setting the base point and one or more align points and performing cutting. This corrects for expansion and contraction of
the media.
Is [AUTO ENV. MATCH] set to the "DISABLE" setting?
The printing and cutting positions may become misaligned due
to ambient temperature or humidity. Setting [AUTO ENV. MATCH]
to "ENABLE" performs matching to the environment to correct
for misalignment.
 P. 84, "Executing Environment Matching Automatically"
Are the settings for the [CALIBRATION] menu item (in
the [CUTTING MENU] menu item) correct?
When you're performing printing followed immediately by cutting, go to [CUTTING MENU] and set the [CALIBRATION] value
to "0.00."
 P. 77, "Performing Distance Correction During Cutting"
5-3 The Media Jams
1
The Media Jams
Introduction
If an error message is displayed because the media
has jammed, immediately correct the problem. Failure
to do so may damage the print heads.
 P. 123, [MOTOR ERROR TURN POWER OFF]
Is the media warped or wrinkled?
Many factors can cause warping or wrinkling. Refer to the following and correct the problem.
 P. 120, "Media Wrinkles or Shrinks, or Feed Is Unstable"
2
Is the height of the print heads too low?
Operation
Try raising the heads higher. Media may inevitably warp or
wrinkle slightly, so adjust the height of the heads to take this
into account.
 P. 72, "Adjusting Head Height to Match Media Thickness (54-inch Model
Only)"
3
Maintenance and
Adjustment
4
Feature
Reference
5
What to Do If
6
Specifications
119
5-4 Media Wrinkles or Shrinks, or Feed Is Unstable
1
Introduction
A variety of problems can occur if the media feed is
not smooth. This can cause such problems as poor
printing quality, contact with the media by the print
heads, misaligned positioning, or media jams. Take
action as follows.
Media Wrinkles or Shrinks
Is the media loaded and set up straight and securely?
2
Feed is not smooth when the media is not straight or is tensioned
unevenly on the left and right. Reload the media.
Operation
Was loaded media allowed to stand for some time?
Media may shrink or wrinkle if it is heated for an extended time.
When printing ends, switch off the sub power or remove the
media.
Are the media clamps mounted?
3
When you're performing printing, be sure to attach the media
clamps.
Maintenance and
Adjustment
Was the media loaded while the print heater was
hot?
Loading media after the print heater has warmed up causes the
temperature of the media to rise suddenly, which may cause the
media to shrink or wrinkle during printing. Before loading media,
switch off the sub power and allow the platen to cool.
4
Is the temperature of the media heating system too
high?
Feature
Reference
Set the temperature to suitable values for the type of media.
 P. 39, "Settings for the Media Heating System"
Is the temperature of room too low?
5
What to Do If
Use this machine in an environment having an ambient temperature of 20 to 32°C (68 to 90°F). If the machine is used at an
ambient temperature less than 20°C, then depending on the type
or width of the media, wrinkling or temperature-caused unevenness may occur. If this happens, try lowering the temperature of
the media heating system by about 2°C.
To obtain stable printing results, however, the machine should
be used at an ambient temperature of 20 to 32°C(68 to 90°F).
Media Feed Is Not Straight
Is the media loaded and set up straight and securely?
6
Feed is not smooth when the media is not straight or is tensioned
unevenly on the left and right. Reload the media.
Specifications
Media Feed Is Not Smooth
120
Do the media or the shafts strike some other object?
Make sure the media and the shafts do not touch anything
else. This may affect output, even when feed appears to be
smooth.
Is the media too thick?
Media that is too thick may not only cause unstable feed, but
may scrape the print heads, resulting in malfunction. Never use
such media.
Are the grit rollers dirty?
Check to make sure the grit rollers are free of buildup of foreign
material such as media scraps.
5-5 The Print Heads Stopped Moving
1
If the print-head carriage stops over the platen, take
action immediately to prevent the heads from drying
out.
Introduction
What to Do First
2
Switch the sub power off, then back on again. (If the media is
jammed, then also remove the media.) If the print-head carriage
move to the standby position (inside the side cover), it means
the operation has ended successfully.
If the print-head carriage did not move, try switching off the
main power, then again switching on the main power, followed
by the sub power.
Operation
If the Heads Still Do Not Move
If the heads still do not move, carry out the following emergency
response measure, then contact your authorized Roland DG
Corp. dealer.
3
Maintenance and
Adjustment
1. Switch off the main power and open the front cover.
2. Detach the side cover.
3.Gently move the print heads to the standby position.
4.Stopping at the place where the audible click is heard locks
the print heads in place.
4
Feature
Reference
5
5.Gently apply pressure from the right side to make sure the
heads don't move to the left.
What to Do If
If the print heads move to the left, again move them slowly by
applying pressure from the left side and make sure they lock
in place.
6
Specifications
121
5-6 If a Message Appears
1
Introduction
These are the main messages that appear on the
machine's display to prompt correct operation. They
do not indicate any error. Follow the prompts and take
action accordingly.
[1■ 2■ 3■ 4■]
Only a small amount of ink remains. Replace the cartridge indicated by the flashing number with a new cartridge.
[PRESS THE POWER KEY TO CLEAN]
2
If you're using ECO-SOL MAX ink, this appears when the machine
has been unused for about one month. Switch on the sub power
once a month.
Operation
 P. 66, "When Not in Use for a Prolonged Period"
[CLOSE THE COVER (FRONT COVER, SIDE COVER
or MAINTENANCE COVER]
Close the front cover, side cover, or maintenance cover. For safety,
the carriage does not operate while a cover is open.
3
[SHEET NOT LOADED SETUP SHEET]
Load media. This message appears when an attempt to perform
a printing test was made while no media was loaded.
Maintenance and
Adjustment
[CHECK DRAIN BOTTLE]
This appears when a certain amount of discharged fluid collects
in the drain bottle. To clear the message, press
. If this
screen appears, go to the [DRAIN BOTTLE] menu and discard the
discharged fluid in the bottle.
 P. 50, "Disposing of Discharged Ink"
4
[INSTALL DRAIN BOTTLE]
Feature
Reference
Check whether the drain bottle is installed. Install the drain
bottle, then press
.
[NOW HEATING...]
5
Wait until the media heating system reaches the preset temperature. Printing starts when
lights up. You can stop
printing by holding down
for one second or longer
while this is displayed. Pressing
makes printing start
immediately, without waiting to reach the preset temperature.
What to Do If
[TIME FOR MAINTENANCE]
It is time to clean the heads using the cleaning kit. After verifying, press
.
 P. 54, "Cleaning the Heads Using the Cleaning Kit"
[TIME FOR WIPER REPLACE]
It is time to replace the wipers. After verifying, press
 P. 58, "Replacing the Wipers"
6
Specifications
122
.
5-7 If an Error Message Appears
[AVOIDING DRY-UP TURN POWER OFF]
The size of the data including the crop marks is
larger than the printing or cutting area of the loaded
media.
[MOTOR ERROR TURN POWER OFF]
A motor error occurred.
Operation cannot be continued. Switch off the sub power. Next,
eliminate the cause of the error, then immediately switch on the
sub power. If the machine is allowed to stand with the error uncorrected, the print heads may dry out and become damaged.
This error may be caused by such factors as a mistake in loading
the media, a media jam, or an operation that pulls the media
with excessive force.
The media has jammed.
123
Specifications
Carefully remove the jammed media. The print heads may also
be damaged. Perform head cleaning, then perform a printing
test and check the results.
6
A problem such as a media jam occurred, impeding correct operation. Operation cannot be continued. Switch the sub power
off, then back on.
To prevent malfunction or damage to the machine, media-cutoff
operations are not performed when [MEDIA CLAMP] is set to
“LONG.” Use
to go back to the original screen, then either
detach the media clamps, or replace them with short media
clamps and set [MEDIA CLAMP] to “SHORT.”
 P. 38, "Cutting Off the Media"
Feature
The cutting carriage and the print-head carriage were
improperly disconnected.
Media cutoff was attempted even though [MEDIA
CLAMP] is set to “LONG.”
What to Do If
[CARRIAGES ARE SEPARATED]
[LONG MEDIA CLAMP IS INSTALLED]
5
Make the scanning-direction size of the data at least 65 mm
(2.6 in).
To continue performing output without correcting this, press
. At this time, the data is output without printing the
crop marks. To stop output, stop sending data from the computer, then raise the loading lever. Change the size of the data,
then send the data again. There is no limitation in the size of the
data in the media-feed direction.
This occurs because the temperature of the location where the
machine is installed is too low. We recommend raising the temperature. To continue waiting for the temperature to rise, press
. To start printing immediately, press
.
Reference
The size of the data being output is too small.
The print heater or dryer did not reach the preset
temperature.
4
To continue performing output without correcting this, press
. At this time, the portion extending beyond the printing or cutting area and the crop marks are not printed. To stop
output, stop sending data from the computer, then raise the
loading lever. Make the printing or cutting area wider, such as by
replacing the media with a larger piece of media or by changing
the positions of the pinch rollers, then send the data again.
[HEATING TIMEOUT CONTINUE?]
Maintenance and
[CAN'T PRINT CROP CONTINUE?]
Operation cannot be continued. Check for a problem with the
connector cable or the computer, and redo the operation from
the step of loading the media.
Adjustment
Operation cannot be continued. Switch the sub power off, then
back on.
Output was stopped because a problem was found
in the data received.
3
The print heads were forced to standby position to
prevent them from drying out.
[DATA ERROR CANCELING...]
Operation
No align point can be set when the angle of the base point and
the align point is too large.
Reload the media correctly, so that the angle is minimized, then
set the base point and the align point again to match the crop
marks.
 P. 96, "Aligning Automatically and Cutting"
Load the media at the correct position and perform detection of
crop marks again. Depending on the media, it may not be possible to detect crop marks automatically. If repeating automatic
crop-mark detection results in an error again, then perform
manual crop-mark detection.
 P. 97, "Aligning Manually and Cutting"
2
An attempt was made to set an align point at a location where the setting cannot be made.
Automatic detection of crop marks could not be accomplished.
Introduction
[ALIGN POINT POSITION INVALID]
[CROPMARK ERROR NOT FOUND]
1
This describes the error messages that may appear
on the machine's display, and how to take action to
remedy the problem. If the action described here
does not correct the problem, or if an error message
not described here appears, contact your authorized
Roland DG Corp. dealer.
5-7 If an Error Message Appears
The media was pulled with excessive force.
1
Introduction
Excessive tension was applied to the media, and additional
action is necessary to recover from this state. First, move the
loading lever to the rear and adjust the media to create a small
amount of slack, then switch on the sub power.
[PINCHROLL ERROR INVALID RIGHT POS]
The right pinch roller is positioned at a location where
it does not pinch the media.
2
Raise the loading lever and move the right pinch roller to the
correct location.
 P. 32, "Loading and Cutting Off Media"
Operation
[PINCHROLL ERROR INVALID LEFT POS]
The left pinch roller is positioned at a location where
it does not pinch the media.
Raise the loading lever and move the left pinch roller to the
correct location.
 P. 32, "Loading and Cutting Off Media"
3
[PINCHROLL ERROR XXX FROM RIGHT]
Maintenance and
Adjustment
The middle pinch rollers are positioned at locations
where they do not pinch the media.
Raise the loading lever and move the middle pinch rollers to
the correct location.
 P. 32, "Loading and Cutting Off Media"
Too many middle pinch rollers are installed.
4
Feature
Reference
Raise the loading lever, then remove all middle pinch rollers that
are not positioned above grit rollers. The number of middle pinch
rollers used varies according to the width of the loaded media.
 P. 32, "Loading and Cutting Off Media"
[SERVICE CALL xxxx]
5
An unrecoverable error occurred, or part replacement
that must be performed by a service technician is
required.
What to Do If
Note the number displayed, then switch off the sub power. After
you switch off the power, inform your authorized Roland DG
Corp. dealer of the number that appeared on the display.
[SHEET TOO SMALL CONTINUE?]
The size of the data is larger than the printing or cutting area of the loaded media.
6
Specifications
To continue performing output without correcting this, press
. At this time, the portion extending beyond the printing or cutting area is not output. To stop output, stop sending
data from the computer, then raise the loading lever. Make the
printing or cutting area wider, such as by replacing the media
with a larger piece of media or by changing the positions of the
pinch rollers, then send the data again.
124
[SHEET SET ERROR SET AGAIN]
The loading lever was lowered while no media was
loaded.
Raise the loading lever, place media at the correct location, then
lower the lever again.
 P. 32, "Loading and Cutting Off Media"
[EDGE DETECTION] is set to "ENABLE," but transparent media was loaded.
Raise the loading lever, set the [EDGE DETECTION] menu item
to "DISABLE," then reload the media.
 P. 78, "Using Transparent Media"
The loaded media is too small.
Press any key to clear the error. Replace with media of usable
size.
[TEMPERATURE IS TOO HIGH **°C]
The temperature of the location where the machine
is installed has risen above the ambient temperature
at which the machine can operate.
Operation cannot be continued. Switch off the sub power. The
displayed temperature is the current ambient temperature of the
installation location. Bring the installed location to a temperature
at which operation is possible (15 to 32°C) and allow the machine
to come to room temperature, then turn on the power.
[TEMPERATURE IS TOO LOW **°C]
The temperature of the location where the machine
is installed has fallen below the ambient temperature
at which the machine can operate.
Operation cannot be continued. Switch off the sub power. The
displayed temperature is the current ambient temperature of the
installation location. Bring the installed location to a temperature
at which operation is possible (15 to 32°C) and allow the machine
to come to room temperature, then turn on the power.
[SET HEAD HEIGHT TO xxx] (54-inch model only)
The height of the print heads is lower than the height
specified on the computer.
This warning indicates that the height of the print heads is too
low for the media thickness specified on the computer.
The heads move to a location where you can operate the
height-adjustment lever. Adjust to the displayed height, then
press
.
 P. 72, "Adjusting Head Height to Match Media Thickness (54inch Model Only)"
[WRONG CARTRIDGE]
A cartridge that cannot be used was installed.
Remove the cartridge to clear the error. Use a cartridge of the
specified type.
1
Introduction
2
Operation
Chapter 6
Specifications
3
Printing/Cutting Area...........................................................................................127
About the Blade .................................................................................................129
Locations of the Power Rating and Serial Number Labels.................................130
Specifications......................................................................................................131
Maintenance and
Adjustment
Usable Media......................................................................................................126
4
Feature
Reference
5
What to Do If
6
Specifications
125
6-1 Usable Media
1
Conditions for Usable Media
Introduction
Media width
54-inch model
210 to 1,371 mm (8.3 to 54 inches)
30-inch model
182 to 762 mm (7.2 to 30 inches)
Cuttable media thickness (A)
2
0.08 to 0.22 mm (3.2 to 8.6 mil)
(depending on media composition)
Operation
Maximum media thickness (including backing paper) (B)
Printing only: 1.0 mm (39 mil)
When performing cutting: 0.4 mm (15 mil)
Roll outer diameter (C)
180 mm (7 in.)
3
Paper tube (core) inner diameter (D)
50.8 mm or 76.2 mm (2 inches or 3 inches)
Maintenance and
Adjustment
Roll weight
54-inch model
30 kg (66 lb.)
30-inch model
20 kg (44 lb.)
Other conditions
4
Media such as the following cannot be used.
Media having an inward curl (i.e., media whose print surface is on the inner side of the roll)
Media whose end is attached to the paper tube (core)
Media which is severely warped or which has a strong tendency to reroll
Media that cannot withstand the heat of the media heating system
Media whose paper tube (core) is bent or crushed
Media that bends under its own weight when loaded
Media on a sagging roll
Media that is rolled unevenly
Feature
Reference
5
This machine cannot necessarily print every kind of media. When selecting media, be sure to carry out
testing in advance to make sure that satisfactory printing quality is obtained.
What to Do If
6
Specifications
126
6-2 Printing/Cutting Area
1
Maximum Area
Max. 1,346 mm (54-inch model)
746 mm (30-inch model)
Introduction
The printing or cutting area along the horizontal plane (the direction in which the carriages move) is determined by the
position of the pinch rollers.
90 mm
Operation
Max. 24,998 mm
2
Printing or cutting area
10 mm 1.5 mm
1.5 mm 10 mm
Pinch roller
3
Printing or cutting coordinates origin (0,0)
4
Maximum Area When Using Crop Marks
Feature
Reference
When crop marks are used, the printing or cutting area is reduced from the maximum area by an amount equal to the crop
marks.
12.5 mm
Maintenance and
75 mm
Adjustment
75 mm
12.5 mm
10 mm
10 mm
5
What to Do If
Printing or cutting area
10 mm
10 mm
12.5 mm
12.5 mm
6
Specifications
Maximum area
Crop mark
127
6-2 Printing/Cutting Area
1
The Media-cutoff Location During Continuous Printing
Introduction
When a media-cutoff command is sent from the computer, the cutoff location on the media is as shown in the figure below.
2
Second page
Operation
75 mm
Location where
separated
Margin
(setting on the computer)
First page
3
Maintenance and
Adjustment
4
Feature
Reference
5
What to Do If
6
Specifications
128
6-3 About the Blade
Media
ZEC-U1005
General signage vinyl
ZEC-U5025
General signage vinyl
Blade force
Amount of blade
offset
Introduction
Blade
Blade life*
(general guide)
50 to 150 gf
0.25 mm
8,000 m
0.25 mm
4,000 m
120 to 200 gf
0.25 mm
4,000 m
Reflective vinyl
100 to 200 gf
0.25 mm
4,000 m
2
30 to 100 gf
Fluorescent vinyl
1
The cutting conditions and the service life of the blade change according to the media and the operating environment,
even when you're using identical blades. The service life also differs according to the type of blade. A rough guide is shown
below.
Operation
When uncut areas remain even when the blade force is increased to a value that is higher by 50 to 60 gf than the values
shown in this chart, then replace the blade.
*The values for "Blade life" are estimates for when an identical type of media is used.
3
Maintenance and
Adjustment
4
Feature
Reference
5
What to Do If
6
Specifications
129
6-4 Locations of the Power Rating and Serial Number Labels
1
Introduction
Serial Number
This is required when you seek maintenance, servicing,
or support. Never peel off the label or let it get dirty.
2
Power Rating
Use an electrical outlet that meets the requirements for
voltage, frequency, and amperage given here.
Operation
3
Maintenance and
Adjustment
4
Feature
Reference
5
What to Do If
6
Specifications
130
6-5 Specifications
Maximum 736 mm (29 in.)
220-cc cartridge / 440-cc cartridge
Four colors (cyan, magenta, yellow, and black)
Maximum 1,440 dpi
10 to 300 mm/s
30 to 300 gf
Roland CAMM-1 series compatible
0 to 1.5 mm (0 to 0.059 in)
0.025 mm/step
Error of less than ±0.3% of distance traveled, or ±0.3 mm, whichever is greater
±0.1 mm or less
±0.5 mm or less
Error of less than ±0.5% of distance traveled, or ±3 mm, whichever is greater
Ethernet (10BASE-T/100BASE-TX, automatic switching)
Automatic sleep feature
AC 100 to 120 V ±10%, 5.5 A, 50/60 Hz or
AC 220 to 240 V ±10%, 2.8 A, 50/60 Hz
Approx. 1030W
Approx. 730W
Approx. 17W
Approx. 17W
64 dB (A) or less (according to ISO 7779)
64 dB (A) or less (according to ISO 7779)
40 dB (A) or less (according to ISO 7779)
40 dB (A) or less (according to ISO 7779)
2,310 (W) x 740 (D) x 1,125 (H) mm
(90.9 (W) x 29.1 (D) x 44.3 (H) in.)
1,700 (W) x 740 (D) x 1,125 (H) mm
(66.9 (W) x 29.1 (D) x 44.3 (H) in.)
112 kg (247 lb.)
89 kg (196 lb.)
Feature
Print heater, setting range for the preset temperature: 30 to 45°C (86 to 112°F)
Dryer, setting range for the preset temperature: 30 to 50°C (86 to 122°F)
AC 100 to 120 V ±10%, 7.6 A, 50/60 Hz or
AC 220 to 240 V ±10%, 3.9 A, 50/60 Hz
Maintenance and
Error of less than ±0.4% of distance traveled, or ±0.3 mm, whichever is greater
When distance correction has been performed (when the setting for [CUTTING
MENU] - [CALIBRATION] has been made): Error of less than ±0.2% of distance traveled, or ±0.1 mm, whichever is greater
What to Do If
Temperature: 15 to 32°C (59 to 90°F) (20°C [68°F] or more recommended), humidity:
35 to 80%RH (non-condensing)
Temperature: 5 to 40°C (41 to 104°F), humidity: 20 to 80%RH (non-condensing)
131
Specifications
Exclusive stands, power cord, blade, blade holder, media clamps, media flanges, replacement blade for separating knife, cleaning kit, software RIP, User's Manual, etc.
6
Accessories
Maximum 1,346 mm (53 in.)
5
Power off
50.8 mm (2 in.) or 76.2 mm (3 in.)
Reference
Weight (with stand)
Environmental
Power on (*9)
Maximum 20 kg (44 lb.)
4
During operation
Sleep mode
Acoustic noise
During operation
level
During standby
Dimensions (with stand) (*8)
Maximum 30 kg (66 lb.)
Adjustment
Power
Maximum 180 mm (7 in.)
3
Connectivity
Power-saving function
Power requirements
Maximum 1.0 mm (39 mil) with liner, for printing
Maximum 0.4 mm (16 mil) with liner and 0.22 mm (9 mil) without liner, for cutting
Operation
Repeatability (when cutting) (*3) (*4)
Alignment accuracy for printing
and cutting (*3) (*5)
Alignment accuracy for printing
and cutting when reloading media
(*3) (*6)
Media heating system (*7)
182 to 762 mm (7.2 to 30 in.)
2
Roll outer diameter
Roll weight
Core diameter
Printing/cutting width (*1)
Ink cartridges
Types
Colors
Printing resolution (dots per inch)
Cutting speed
Blade force
Cutting blade
Type
Blade offset
Software resolution (when cutting)
Distance accuracy (when printing)
(*2) (*3)
Distance accuracy (when cutting)
(*3)
Piezoelectric inkjet
210 to 1,371 mm (8.3 to 54 in.)
Introduction
Printing technology
Media
Width
Thickness
VP-300i
1
VP-540i
6-5 Specifications
1
*1
The length of printing or cutting is subject to the limitations of the program.
Introduction
*2
○ With Roland PET film, print travel: 1 m
○ Temperature: 25°C (77°F), humidity: 50%
*3
Not assured when the print heater or dryer is used.
2
Operation
3
*4
The following conditions must be met:
○ Media type: Media specified by Roland DG Corp.
○ Roll media must be loaded on the shaft.
○ [PREFEED] menu item must be set to "ENABLE."
○ Side margins: 25 mm or more for both the left and right margins
○ Front margin: 35 mm or more
○ Excluding expansion/contraction of the media
Range for assured repetition accuracy
○ 54-inch model
For media with a width exceeding 610 mm: Length 4,000 mm
For media with a width of 610 mm or less: Length 8,000 mm
○ 30-inch model
Length 3,000 mm
Maintenance and
Adjustment
*5
○ Provided that media length is under 3,000 mm
○ Temperature: 25°C (77°F)
○ Excluding possible shift caused by expansion/contraction of the media and/or by reloading the media.
*6
4
○ Media type : Roland PET film
○ Data size: 1,000 mm in the media-feed direction, 1,346 mm (54-inch model) or 736 mm (30-inch model) in the carriage-movement
direction
Feature
Reference
○ No lamination
○ Automatic detection of crop marks at 4 points when media is reloaded.
○ During cutting, [PREFEED] menu item must be set to "ENABLE."
○ Temperature: 25°C (77°F)
○ Excludes the effects of slanted movement and of expansion and contraction of the media.
*7
5
○ Warm-up is required after powerup. This may require 5 to 20 minutes, depending on the operating environment.
○ Depending on the ambient temperature and media width, the preset temperature may fail to be reached.
What to Do If
*8
○ Depth when the included ink-cartridge tray is installed is 1,000 mm.
*9
Operating environment
6
Use in an operating environment
with this range.
Specifications
132
133
134
R1-081212
Download PDF
Similar pages