SUPER STORAGE SYSTEM
6048R-E1CR24H
USER’S MANUAL
1.0a
Preface
The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and documentation, is the property of Supermicro and/or its licensors, and is supplied only under a license.
Any use or reproduction of this product is not allowed, except as expressly permitted by the terms
of said license.
IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class A
digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the manufacturer’s instruction manual, may cause harmful interference
with radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference, in which case you will be required to correct the interference at your own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to the
State of California to cause birth defects and other reproductive harm.
Manual Revision 1.0a
Release Date: May 13, 2016
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Preface
About This Manual
This manual is written for professional system integrators and PC technicians. It
provides information for the installation and use of the 6048R-E1CR24H. Installation
and maintainance should be performed by experienced technicians only.
The 6048R-E1CR24H is a high-end storage system based on the SC846BE1CR920B 4U rackmountable chassis and the X10DRH-iT dual processor serverboard.
Manual Organization
Chapter 1: Introduction
The first chapter provides a checklist of the main components included with the
system and describes the main features of the X10DRH-iT serverboard and the
SC846BE1C-R920B chassis.
Chapter 2: Server Installation
This chapter describes the steps necessary to install the 6048R-E1CR24H into a
rack and check out the server configuration prior to powering up the system. If your
server was ordered without processor and memory components, this chapter will
refer you to the appropriate sections of the manual for their installation.
Chapter 3: System Interface
Refer here for details on the system interface, which includes the functions and
information provided by the control panel on the chassis as well as other LEDs
located throughout the system.
Chapter 4: Standardized Warning Statements
You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
6048R-E1CR24H.
Copyright © 2016 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America
iii
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Chapter 5: Advanced Serverboard Setup
Preface
Notes
Chapter 5 provides detailed information on the X10DRH-iT serverboard, including
the locations and functions of connections, headers and jumpers. Refer to this
chapter when adding or removing processors or main memory and when reconfiguring the serverboard.
Chapter 6: Advanced Chassis Setup
Refer to Chapter 6 for detailed information on the SC846BE1C-R920B chassis.
You should follow the procedures given in this chapter when installing, removing
or reconfiguring hard drives and when replacing system power supply units and
cooling fans.
Chapter 7: BIOS
The BIOS chapter includes an introduction to BIOS and provides detailed information on running the CMOS Setup Utility.
Appendix A: BIOS Error Beep Codes
Appendix B: System Specifications
iv
v
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Table of Contents
Table of Contents
Chapter 3 System Interface
3-1Overview.......................................................................................................... 3-1
3-2
Chapter 1 Introduction
1-2
1-3
1-4
Power............................................................................................................... 3-1
Serverboard Features...................................................................................... 1-2
Processors....................................................................................................... 1-2
Control Panel Buttons...................................................................................... 3-1
Reset................................................................................................................ 3-1
1-1Overview.......................................................................................................... 1-1
3-3
Control Panel LEDs......................................................................................... 3-1
Memory............................................................................................................ 1-2
Power Fail........................................................................................................ 3-2
Main Storage Controller................................................................................... 1-2
Information LED............................................................................................... 3-2
Serial ATA......................................................................................................... 1-2
NIC1................................................................................................................. 3-2
PCI Expansion Slots........................................................................................ 1-2
NIC2................................................................................................................. 3-3
Rear I/O Ports.................................................................................................. 1-2
HDD.................................................................................................................. 3-3
Onboard Graphics............................................................................................ 1-3
Power............................................................................................................... 3-3
Server Chassis Features................................................................................. 1-3
3-4
System Power.................................................................................................. 1-3
Chapter 4 Standardized Warning Statements for AC Systems
Drive Carrier LEDs........................................................................................... 3-3
Hard Drives...................................................................................................... 1-3
4-1
About Standardized Warning Statements........................................................ 4-1
Front Control Panel.......................................................................................... 1-3
Warning Definition............................................................................................ 4-1
Cooling System................................................................................................ 1-3
Installation Instructions..................................................................................... 4-4
Contacting Supermicro..................................................................................... 1-5
Circuit Breaker................................................................................................. 4-5
Power Disconnection Warning......................................................................... 4-6
Chapter 2 Server Installation
2-1Overview.......................................................................................................... 2-1
Equipment Installation...................................................................................... 4-8
2-2
Unpacking the System..................................................................................... 2-1
Restricted Area................................................................................................. 4-9
2-3
Preparing for Setup.......................................................................................... 2-1
Battery Handling............................................................................................. 4-10
Choosing a Setup Location.............................................................................. 2-1
Redundant Power Supplies........................................................................... 4-12
Warnings and Precautions............................................................................... 2-2
Backplane Voltage......................................................................................... 4-13
Rack Precautions............................................................................................. 2-2
Comply with Local and National Electrical Codes......................................... 4-14
Server Precautions........................................................................................... 2-2
Product Disposal............................................................................................ 4-15
Rack Mounting Considerations........................................................................ 2-3
Hot Swap Fan Warning.................................................................................. 4-16
Ambient Operating Temperature................................................................. 2-3
Power Cable and AC Adapter ....................................................................... 4-18
2-4
Reduced Airflow.......................................................................................... 2-3
Chapter 5 Advanced Serverboard Setup
Mechanical Loading.................................................................................... 2-3
5-1
Precautions...................................................................................................... 5-1
Circuit Overloading...................................................................................... 2-3
Reliable Ground.......................................................................................... 2-3
2-5
Handling the Serverboard................................................................................ 5-1
5-2
Connecting Cables........................................................................................... 5-2
Installing the System into a Rack.................................................................... 2-4
Connecting Data Cables.................................................................................. 5-2
Separating the Sections of the Rack Rails...................................................... 2-4
Connecting Power Cables............................................................................... 5-2
Connecting the Control Panel.......................................................................... 5-2
Installing the Inner (Chassis) Rails.................................................................. 2-5
Installing the Outer (Rack) Rails...................................................................... 2-6
5-3
Rear I/O Ports.................................................................................................. 5-3
Installing the Sytem into a Rack...................................................................... 2-7
5-4
Installing the Processor and Heatsink............................................................. 5-4
Installing the Chassis into a Rack................................................................... 2-8
vi
Installing an LGA2011 Processor..................................................................... 5-4
vii
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Table of Contents
Installing a Passive CPU Heatsink.................................................................. 5-7
7-3 Advanced Setup Configurations...................................................................... 7-4
Removing the Heatsink.................................................................................... 5-7
7-4 Event Logs..................................................................................................... 7-40
Installing Memory............................................................................................. 5-8
7-5 IPMI................................................................................................................ 7-42
Memory Support............................................................................................... 5-8
7-6
Security Settings............................................................................................ 7-44
DIMM Installation............................................................................................. 5-8
7-7
Boot Settings.................................................................................................. 7-45
5-6
Adding PCI Expansion Cards.........................................................................5-11
7-8 Save & Exit.................................................................................................... 7-46
5-7
Serverboard Details....................................................................................... 5-12
Appendix A BIOS POST Error Codes
5-5
X10DRH-iT Quick Reference......................................................................... 5-13
5-8
Connector Definitions .................................................................................... 5-14
5-9
Jumper Settings............................................................................................. 5-21
Appendix B System Specifications
5-10 Onboard Indicators......................................................................................... 5-24
5-11 SATA Ports..................................................................................................... 5-25
5-12 Installing Software.......................................................................................... 5-26
SuperDoctor® 5............................................................................................. 5-27
5-13 Onboard Battery............................................................................................. 5-28
Chapter 6 Advanced Chassis Setup
6-1
Static-Sensitive Devices................................................................................... 6-1
Precautions...................................................................................................... 6-1
6-2
Control Panel................................................................................................... 6-2
6-3
Removing the Chassis Cover.......................................................................... 6-3
6-4
System Fans.................................................................................................... 6-4
System Fan Failure.......................................................................................... 6-4
Replacing System Fans................................................................................... 6-4
Rear Exhaust Fans.......................................................................................... 6-4
6-5
Drive Bay Installation/Removal........................................................................ 6-5
Accessing the Drive Bays................................................................................ 6-5
SATA Drive Installation..................................................................................... 6-6
Hard Drive Backplane................................................................................. 6-7
Removing the Air Shroud................................................................................. 6-8
6-6
Power Supply................................................................................................... 6-9
Power Supply Failure....................................................................................... 6-9
6-7
Attaching a JBOD Expansion Chassis........................................................... 6-10
Chapter 7 BIOS
7-1 Introduction....................................................................................................... 7-1
Starting BIOS Setup Utility............................................................................... 7-1
How To Change the Configuration Data.......................................................... 7-1
How to Start the Setup Utility.......................................................................... 7-2
7-2 Main Setup....................................................................................................... 7-2
viii
ix
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Notes
x
Chapter 1: Introduction
Chapter 1
Introduction
1-1Overview
The 6048R-E1CR24H is a high-end storage system comprised of two main subsystems: the SC846BE1C-R920B 4U/rack mount chassis and the X10DRH-iT dual
processor serverboard. Please refer to our website for information on operating
systems that have been certified for use with the system (www.supermicro.com).
In addition to the serverboard and chassis, various hardware components have
been included with the 6048R-E1CR24H, as listed below:
•Two passive CPU heatsinks (SNK-P0048PS)
•Three 8-cm system fans (FAN-0127L4)
•Two 8-cm exhaust fans (FAN-0125L4)
•One air shroud (MCP-310-49003-0N)
•SATA accessories
One SAS3/SATA3 backplane (BPN-SAS3-846EL1)
Twenty-four drive carriers (MCP-220-00075-0B)
•Hardware RAID controller ( AOC-S3108L-H8IR)
•JBOD expansion port (AOM-SAS3-8I8E-LP)
•One rackmount kit (MCP-290-00057-0N)
Note: For your system to work properly, please follow the links below to download
all necessary drivers/utilities and the user’s manual for your server.
•Supermicro product manuals: http://www.supermicro.com/support/manuals/
•Product drivers and utilities: ftp://ftp.supermicro.com
•Product safety info: http://www.supermicro.com/about/policies/safety_information.cfm
•If you have any questions, please contact our support team at:
support@supermicro.com
1-1
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
1-2 Serverboard Features
The 6048R-E1CR24H is built around the X10DRH-iT, a dual processor serverboard
based on the Intel C612 chipset. Below are the main features of the X10DRH-iT.
(See Figure 1-1 for a block diagram of the chipset.)
Chapter 1: Introduction
JBOD expansion ports. A UID (Unit Identifier) button and LED are also located
beside the VGA port.
Onboard Graphics
Graphics are provided by an onboard ASpeed AST 2400 BMC, which supports IPMI.
Processors
The X10DRH-iT supports single or dual Intel® Xeon E5-2600 (v3/v4) Series processors. Please refer to the serverboard description pages on our website for a
complete listing of supported processors (www.supermicro.com).
1-3 Server Chassis Features
The SC846BE1C-R920B is a 4U form factor chassis designed to be used in a
storage configuration. The following is a general outline of the main features of the
SC846BE1C-R920B chassis.
Memory
The X10DRH-iT has 16 DIMM slots that can support up to 2 TB of Load Reduced
(LRDIMM) or 1 TB of Registered (RDIMM) ECC DDR4-2400/2133/1866/1600
memory. See Chapter 5 for details.
System Power
The SC846BE1C-R920B features a redundant (two separate power modules) 920W
high-efficiency power supply with I2C. This power redundancy feature allows you to
replace a failed power supply without shutting down the system.
Main Storage Controller
An LSI 3108 controller card is included in the system to support up to 240 SATA
3.0/SAS 3.0 hard drives. (RAID 0, 1, 5, 6, 10, 50 and 60 supported). The SATA/
SAS drives are hot-swappable units.
Serial ATA
A SATA controller is integrated into the chipset to provide 10 SATA 3.0 (6/Gbps)
ports (I-SATA0-5 supported by the Intel PCH and a vertical 4-port S-SATA connection supported by the Intel SCU), which are RAID 0, 1 and 10 supported. The
SATA drives are hot-swappable units. (RAID 5 supported with Windows OS only.)
Hard Drives
The SC846BE1C-R920B chassis was designed to support 24 SAS/SATA hard
drives, which are hot-swappable units.
Front Control Panel
The control panel provides you with system monitoring and control. LEDs indicate
system power, HDD activity, network activity, system overheat/fan fail and power
supply failure. A main power button and a system reset button are also included.
In addition, two USB ports and a COM port have been incorporated into the front
of the chassis for convenient access.
PCI Expansion Slots
The X10DRH-iT has three PCI-Express 3.0 x8 slots (CPU2 Slot1/Slot2/Slot6), two
PCI-Express 3.0 x16 slots (CPU1 Slot3/ CPU2 Slot5) and one PCI-Express 2.0 x4
in x8 slot (CPU2 Slot4). With the RAID controller card and JBOD ports occupying
two of these slots, one PCI-E 3.0 x16 and three PCI-E 3.0 x8 expansion cards may
be added to the system
Cooling System
The SC846BE1C-R920B chassis includes three 8-cm hot-plug system cooling fans
located in the middle section of the chassis. Two additional 8-cm fans are located
at the back of the chassis to expel hot air from the system. An air shroud channels
the airflow from the system fans to efficiently cool the processors and memory. Each
power supply module also includes a cooling fan.
Rear I/O Ports
The I/O ports include one COM port, a VGA port, four USB (two USB 3.0 and two
USB 2.0), two 10G (TLAN) Ethernet ports, a dedicated IPMI LAN port and dual
1-2
1-3
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Chapter 1: Introduction
1-4 Contacting Supermicro
Figure 1-1. Intel C612 Chipset:
System Block Diagram
Headquarters
Address:
Note: This is a general block diagram. Please see Chapter 5 for details.
980 Rock Ave.
X10DRH-C/i (T)
San Jose, CA 95131 U.S.A.
VR12.5
5 PHASE
145W
DDR4
1333/2133
CPU1
#2
P1
#3
DMI 2
QPI
9.6G
QPI
9.6G
P1
CPU2
P0
#1
#2
#3
DMI 2
PVCCIO
(1.05/0.95)
from 3.3v
2 x PCI-E X8 G3
PCI-E X8 G3 (LAN REVERSE)
#9
#8
#7
#6
#5
#4
#3
#2
#1
#0
RMII/NCSI
PCH 612
SPI
AST2400
USB 3.0
SPI
TPM HEADER
COM1
Connector
Temp Sensor
Europe
Address:
PCI-E X8
SLOT 7
S-SATA 7,8,9,10
Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel:
+31 (0) 73-6400390
Fax:
+31 (0) 73-6416525
Email:
sales@supermicro.nl (General Information)
support@supermicro.nl (Technical Support)
EMC1402-1 *2 at diff SMBUS
USB2
USB 0/1, 2/3
COM2
Header
Website:
USB 4/5, 6, 7/8
Address:
www.supermicro.nl
Debug Card
Zhonghe Dist., New Taipei City 235
BIOS
HEADER
Taiwan (R.O.C)
SYSTEM POWER
FRONT PANEL
1-4
Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
SPI
LPC
VGA CONN
SATADOM 5,6
www.supermicro.com
Asia-Pacific
SPI
BIOS
I-SATA 0,1,2,3
USB 2.0
USB3
BMC Boot Flash
USB 2.0
PCI-E X1 G2
BMC
DDR3
marketing@supermicro.com (General Information)
rma@supermicro.nl (Customer Support)
RGRMII
LAN3
PCI-E X8
SLOT 5
PCI-E X8
SLOT 2
PCI-E X8 G3
X540/I350
RTL8211E-VB-CG
+1 (408) 503-8008
Email:
PCI-E X8 G2
LAN1,2
6.0 Gb/S
RJ45
Fax:
SATA
SLOT 3
PCI-E X8
SLOT 1
PCI-E X8
2 x PCI-E X8 G3 (LAN REVERSE)
PCI-E X16 G3
PCI-E X8
SLOT 6
PCI-E X8 G3
+1 (408) 503-8000
Website:
PCI-E X16
SLOT 4
3108
Tel:
support@supermicro.com (Technical Support)
DDR4
P0
#1
#2-8
#2-7
#2-6
#2-5
#2-4
#2-3
#2-2
#2-1
VCCP1 12v
VR12.5
5 PHASE
145W
1333/2133
#1-8
#1-7
#1-6
#1-5
#1-4
#1-3
#1-2
#1-1
LSI
Super Micro Computer, Inc.
FAN SPEED
CTRL
Tel:
+886-(2) 8226-3990
Fax:
+886-(2) 8226-3992
Email:
support@supermicro.com.tw
Website:
www.supermicro.com.tw
1-5
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Notes
1-6
Chapter 2: Server Installation
Chapter 2
Server Installation
2-1Overview
This chapter provides a quick setup checklist to get your SuperServer up and
running. Following these steps in the order given should enable you to have the
system operational within a minimum amount of time. This quick setup assumes
that your system has come to you with the processors and memory preinstalled. If
your system is not already fully integrated with a serverboard, processors, system
memory etc., please turn to the chapter or section noted in each step for details on
installing specific components.
2-2 Unpacking the System
You should inspect the box the 6048R-E1CR24H was shipped in and note if it was
damaged in any way. If the server itself shows damage you should file a damage
claim with the carrier who delivered it.
Decide on a suitable location for the rack unit that will hold the 6048R-E1CR24H.
It should be situated in a clean, dust-free area that is well ventilated. Avoid areas
where heat, electrical noise and electromagnetic fields are generated. You will also
need it placed near a grounded power outlet. Read the Rack and Server Precautions in the next section.
2-3 Preparing for Setup
The box the 6048R-E1CR24H was shipped in should include two sets of rail assemblies, two rail mounting brackets and the mounting screws you will need to install the
system into the rack. Follow the steps in the order given to complete the installation
process in a minimum amount of time. Please read this section in its entirety before
you begin the installation procedure outlined in the sections that follow.
Choosing a Setup Location
•Leave enough clearance in front of the rack to enable you to open the front door
completely (~25 inches) and approximately 30 inches of clearance in the back
of the rack to allow for sufficient airflow and ease in servicing.
•This product is for installation only in a Restricted Access Location (dedicated
equipment rooms, service closets and the like).
2-1
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
•This product is not suitable for use with visual display work place devices
acccording to §2 of the the German Ordinance for Work with Visual Display Units.
Chapter 2: Server Installation
Rack Mounting Considerations
Ambient Operating Temperature
2-4 Warnings and Precautions
Rack Precautions
•Ensure that the leveling jacks on the bottom of the rack are fully extended to
the floor with the full weight of the rack resting on them.
•In single rack installation, stabilizers should be attached to the rack. In multiple
rack installations, the racks should be coupled together.
•Always make sure the rack is stable before extending a component from the
rack.
•You should extend only one component at a time - extending two or more simultaneously may cause the rack to become unstable.
If installed in a closed or multi-unit rack assembly, the ambient operating temperature of the rack environment may be greater than the ambient temperature of the
room. Therefore, consideration should be given to installing the equipment in an
environment compatible with the manufacturer’s maximum rated ambient temperature (Tmra).
Reduced Airflow
Equipment should be mounted into a rack so that the amount of airflow required
for safe operation is not compromised.
Mechanical Loading
Equipment should be mounted into a rack so that a hazardous condition does not
arise due to uneven mechanical loading.
Circuit Overloading
Server Precautions
•Review the electrical and general safety precautions in Chapter 4.
•Determine the placement of each component in the rack before you install the
Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on overcurrent protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.
rails.
•Install the heaviest server components on the bottom of the rack first, and then
work up.
•Use a regulating uninterruptible power supply (UPS) to protect the server from
power surges, voltage spikes and to keep your system operating in case of a
power failure.
•Allow any hot plug drives and power supply modules to cool before touching
them.
•Always keep the rack's front door and all panels and components on the servers
closed when not servicing to maintain proper cooling.
Reliable Ground
A reliable ground must be maintained at all times. To ensure this, the rack itself
should be grounded. Particular attention should be given to power supply connections other than the direct connections to the branch circuit (i.e. the use of power
strips, etc.).
Warning! To prevent bodily injury when mounting or servicing this unit in a
rack, you must take special precautions to ensure that the system remains
stable. The following guidelines are provided to ensure your safety:
•This unit should be mounted at the bottom of the rack if it is the only unit in
the rack.
•When mounting this unit in a partially filled rack, load the rack from the bottom
to the top with the heaviest component at the bottom of the rack.
•If the rack is provided with stabilizing devices, install the stabilizers before
mounting or servicing the unit in the rack.
2-2
2-3
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Chapter 2: Server Installation
2-5 Installing the System into a Rack
Installing the Inner (Chassis) Rails
This section provides information on installing the S846 chassis into a rack unit with
Installing the Inner Rails
the quick-release rails provided. There are a variety of rack units on the market,
which may mean the assembly procedure will differ slightly. You should also refer
1. Extend the inner rail toward the front of the rail assembly as far as possible,
then depress the locking tab to pull it completely out.
to the installation instructions that came with the rack unit you are using.
2. Place the inner rail on the side of the chassis aligning the hooks of the chassis with the rail extension holes.
Separating the Sections of the Rack Rails
The chassis package includes two rail assemblies in the rack mounting kit. Each
assembly consists of two sections: an inner fixed chassis rail that secures directly to
the server chassis and an outer fixed rack rail that secures directly to the rack itself.
3. Slide the extension toward the front of the chassis.
4. You may secure the chassis with screws if desired.
Separating the Inner and Outer Rails
5. Repeat steps 1-3 for the other inner rail.
1. Locate the rail assembly in the chassis packaging.
2. Extend the rail assembly by pulling it outward.
3. Press the quick-release tab.
4. Separate the inner rail extension from the outer rail assembly.
Figure 2-1. Separating the Rack Rails
1
F.
Rail Assembly
SCREW
12
Extending the Rails
12
13
2
13
Quick-Release
Tab
1
Figure 2-2. Installing the Inner Rails
Note: 3U system shown above, rails are common to the SC846 also.
14
Separating the Inner
Rail Extension
2-4
Warning: do not pick up the server with the front handles. They are designed to pull the system from a rack only.
2-5
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Installing the Outer (Rack) Rails
Outer rails attach to the server rack and hold the server in place. The outer rails
for the chassis extend between 30 inches and 33 inches.
Installing the Outer Rails
1. Attach the right outer rail to the rack by inserting the hooks included on the
rails into the holes provided on the rack.
2. If desired, screw the rails to the chassis for added support.
3. Repeat these steps for the left outer rail.
Chapter 2: Server Installation
Installing the Sytem into a Rack
Installing into a Rack
1. Confirm that the inner and outer rails are properly installed.
2. Line up the inner (chassis) rails with the front of the outer (rack) rails.
3. Slide the chassis rails into the rack rails, keeping the pressure even on both
sides (you may have to depress the locking tabs when inserting). When the
server has been pushed completely into the rack, you should hear the locking
tabs "click" into position.
4. (Optional) Insert and tighten the thumbscrews that hold the front of the server
to the rack.
Warning: Slide rail mounted equipment is not to be used as a shelf or a
work space.
Figure 2-3. Outer Rails
Warning: In any instance of pulling the system from the rack, always use
a rack lift and follow all associated safety precautions.
Warning: Stability hazard. The rack stabilizing mechanism must be in
place, or the rack must be bolted to the floor before you slide the unit out
for servicing. Failure to stabilize the rack can cause the rack to tip over.
Figure 2-4. Installing the Outer Rails
Warning: When initially installing the server to a rack, test that the rail
locking tabs engage to prevent the server from being overextended. Have
a rack lift in place as a precaution in case the test fails.
2-6
2-7
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
1B
1A
Figure 2-5. Installing the Rack Rails
Installing the Chassis into a Rack
Installing the Chassis into a Rack
1. Confirm that chassis includes the inner rails (A), also confirm that the outer
rails (B) are installed on the rack.
2. Align chassis rails (A) with the front of the rack rails (B).
3. Slide the chassis rails into the rack rails, keeping the pressure even on both
sides (you may have to depress the locking tabs when inserting). When the
server has been pushed completely into the rack, you should hear the locking
tabs "click" into the locked position.
4. Tighten up all the screws on the front side and rear side of both outer rails.
5. (Optional) Insert and tightening the thumbscrews that hold the front of the
server to the rack.
2-8
Chapter 3: System Interface
Chapter 3
System Interface
3-1Overview
There are several LEDs on the control panel as well as others on the hard drive
carriers to keep you constantly informed of the overall status of the system as well
as the activity and health of specific components. There are also two buttons on
the chassis control panel.
3-2 Control Panel Buttons
The two push-buttons located on the front of the chassis are (in order from left to
right) a reset button and a power on/off button.
Reset
Use the reset button to reboot the system.
Power
This is the main power button, which is used to apply or turn off the main system
power. Turning off system power with this button removes the main power but keeps
standby power supplied to the system. Therefore, the system power cord should
be unplugged before performing service.
3-3 Control Panel LEDs
The control panel located on the front of the chassis has several LEDs. These
LEDs provide you with critical information related to different parts of the system.
This section explains what each LED indicates when illuminated and any corrective
action you may need to take.
3-1
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Chapter 3: System Interface
2
NIC2
Power Fail
Indicates a power supply module has failed. The second power supply module will
take the load and keep the system running but the failed module will need to be
replaced. Refer to Chapter 6 for details on replacing the power supply. This LED
should be off when the system is operating normally.
Indicates network activity on the LAN2 port when flashing.
HDD
Indicates IDE channel activity. On the SuperServer 6048R-E1CR24H, this LED
indicates hard and/or DVD-ROM drive activity when flashing.
Information LED
The Information LED provides alerts for several states, as noted in the table below.
Information LED
Status
Description
Continuously on and red
An overheat condition has occured.
(This may be caused by cable congestion.)
Blinking red (1Hz)
Fan failure, check for an inoperative fan.
Blinking red (0.25Hz)
Power failure, check for a non-operational power supply.
Solid blue
Local UID has been activated. Use this function to locate
the server in a rack mount environment.
Blinking blue
Remote UID is on. Use this function to identify the
server from a remote location.
Power
Indicates power is being supplied to the system's power supply units. This LED
should normally be illuminated when the system is operating.
3-4 Drive Carrier LEDs
The chassis includes externally accessible SAS/SATA drives. Each drive carrier
displays two status LEDs on the front of the carrier.
LED
1
Activity LED
NIC1
Indicates network activity on the LAN1 port when flashing.
Status LED
3-2
LED Color
State
Status
Blue
Solid On
SAS drive installed
Blue
Blinking
I/O activity
Blue
Dark/off
SATA drive installed or empty
(run I/O to verify)
Red
Solid On
Failed drive for SAS/SATA
Red
Blinking at 1 Hz
Rebuild drive for SAS/SATA
Red
Blinking with two
blinks and one stop
at 1 Hz
Hot spare for SAS/SATA
Red
On for five
seconds, then off
Power on for SAS/SATA
Red
Blinking at 4 Hz
Identify/locate drive for SAS/
SATA
3-3
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Notes
3-4
Chapter 4: Warning Statements for AC Systems
Chapter 4
Standardized Warning Statements for AC Systems
4-1 About Standardized Warning Statements
The following statements are industry standard warnings, provided to warn the user
of situations which have the potential for bodily injury. Should you have questions
or experience difficulty, contact Supermicro's Technical Support department
for assistance. Only certified technicians should attempt to install or configure
components.
Read this appendix in its entirety before installing or configuring components in the
Supermicro chassis.
These warnings may also be found on our web site at http://www.supermicro.com/
about/policies/safety_information.cfm.
Warning Definition
Warning!
This warning symbol means danger. You are in a situation that could cause bodily
injury. Before you work on any equipment, be aware of the hazards involved with
electrical circuitry and be familiar with standard practices for preventing accidents.
警告の定義
この警告サインは危険を意味します。
人身事故につながる可能性がありますので、いずれの機器でも動作させる前に、
電気回路に含まれる危険性に注意して、標準的な事故防止策に精通して下さい。
此警告符号代表危险。
您正处于可能受到严重伤害的工作环境中。在您使用设备开始工作之前,必须充分
意识到触电的危险,并熟练掌握防止事故发生的标准工作程序。请根据每项警告结
尾的声明号码找到此设备的安全性警告说明的翻译文本。
此警告符號代表危險。
您正處於可能身體可能會受損傷的工作環境中。在您使用任何設備之前,請注意觸
電的危險,並且要熟悉預防事故發生的標準工作程序。請依照每一注意事項後的號
碼找到相關的翻譯說明內容。
4-1
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Warning Statements for AC Systems
Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu
Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den
Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung
vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen
Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
. ‫تحذٌز!هذا الزهز ٌعًٌ خطز اًك فً حالة ٌوكي أى تتسبب فً اصابة جسذٌة‬
‫كي على علن بالوخاطز الٌاجوة عي الذوائز‬،‫قبل أى تعول على أي هعذات‬
‫الكهزبائٍة‬
‫وكي على دراٌة بالووارسات الىقائٍة لوٌع وقىع أي حىادث‬
‫استخذم رقن البٍاى الوٌصىص فً ًهاٌة كل تحذٌز للعثىر تزجوتها‬
안전을 위한 주의사항
BEWAHREN SIE DIESE HINWEISE GUT AUF.
경고!
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes
de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y
familiarícese con los procedimientos estándar de prevención de accidentes. Al
final de cada advertencia encontrará el número que le ayudará a encontrar el texto
traducido en el apartado de traducciones que acompaña a este dispositivo.
이 경고 기호는 위험이 있음을 알려 줍니다. 작업자의 신체에 부상을 야기 할 수
있는 상태에 있게 됩니다. 모든 장비에 대한 작업을 수행하기 전에 전기회로와
관련된 위험요소들을 확인하시고 사전에 사고를 방지할 수 있도록 표준
작업절차를 준수해 주시기 바랍니다.
GUARDE ESTAS INSTRUCCIONES.
해당 번역문을 찾기 위해 각 경고의 마지막 부분에 제공된 경고문 번호를
참조하십시오
IMPORTANTES INFORMATIONS DE SÉCURITÉ
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une
situation pouvant entraîner des blessures ou des dommages corporels. Avant
de travailler sur un équipement, soyez conscient des dangers liés aux circuits
électriques et familiarisez-vous avec les procédures couramment utilisées pour
éviter les accidents. Pour prendre connaissance des traductions des avertissements
figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.
Dit waarschuwings symbool betekent gevaar. U verkeert in een situatie die
lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken,
dient u zich bewust te zijn van de bij een elektrische installatie betrokken risico's
en dient u op de hoogte te zijn van de standaard procedures om ongelukken te
voorkomen. Gebruik de nummers aan het eind van elke waarschuwing om deze te
herleiden naar de desbetreffende locatie.
BEWAAR DEZE INSTRUCTIES
CONSERVEZ CES INFORMATIONS.
‫תקנון הצהרות אזהרה‬
‫ על מנת להזהיר את המשתמש מפני חבלה‬,‫הצהרות הבאות הן אזהרות על פי תקני התעשייה‬
‫ יש ליצור קשר עם מחלקת תמיכה‬,‫ במידה ויש שאלות או היתקלות בבעיה כלשהי‬.‫פיזית אפשרית‬
.‫ טכנאים מוסמכים בלבד רשאים להתקין או להגדיר את הרכיבים‬.‫טכנית של סופרמיקרו‬
.‫יש לקרוא את הנספח במלואו לפני התקנת או הגדרת הרכיבים במארזי סופרמיקרו‬
4-2
4-3
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Installation Instructions
Chapter 4: Warning Statements for AC Systems
Circuit Breaker
Warning!
Warning!
Read the installation instructions before connecting the system to the power source.
設置手順書
This product relies on the building's installation for short-circuit (overcurrent)
protection. Ensure that the protective device is rated not greater than: 250 V, 20 A.
サーキット・ブレーカー
システムを電源に接続する前に、設置手順書をお読み下さい。
この製品は、短絡(過電流)保護装置がある建物での設置を前提としています。
警告
将此系统连接电源前,请先阅读安装说明。
警告
將系統與電源連接前,請先閱讀安裝說明。
Warnung
保護装置の定格が250 V、20 Aを超えないことを確認下さい。
警告
此产品的短路(过载电流)保护由建筑物的供电系统提供,确保短路保护设备的额定电
流不大于250V,20A。
Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen
lesen.
警告
此產品的短路(過載電流)保護由建築物的供電系統提供,確保短路保護設備的額定電
流不大於250V,20A。
¡Advertencia!
Warnung
Lea las instrucciones de instalación antes de conectar el sistema a la red de
alimentación.
Dieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschlussbzw. Überstromschutz installiert ist. Stellen Sie sicher, dass der Nennwert der
Schutzvorrichtung nicht mehr als: 250 V, 20 A beträgt.
Attention
Avant de brancher le système sur la source d'alimentation, consulter les directives
d'installation.
.‫יש לקרוא את הוראות התקנה לפני חיבור המערכת למקור מתח‬
‫اقر إرشادات التركيب قبل توصيل النظام إلى مصدر للطاقة‬
시스템을 전원에 연결하기 전에 설치 안내를 읽어주십시오.
Waarschuwing
Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron
aansluit.
4-4
¡Advertencia!
Este equipo utiliza el sistema de protección contra cortocircuitos (o sobrecorrientes)
del edificio. Asegúrese de que el dispositivo de protección no sea superior a: 250
V, 20 A.
Attention
Pour ce qui est de la protection contre les courts-circuits (surtension), ce produit
dépend de l'installation électrique du local. Vérifiez que le courant nominal du
dispositif de protection n'est pas supérieur à :250 V, 20 A.
‫ יש לוודא כי‬.‫מוצר זה מסתמך על הגנה המותקנת במבנים למניעת קצר חשמלי‬
60VDC, 20A-‫המכשיר המגן מפני הקצר החשמלי הוא לא יותר מ‬
‫هذا المنتج يعتمد على معداث الحمايت مه الدوائرالقصيرة التي تم تثبيتها في‬
‫المبنى‬
20A, 250VDC :‫تأكد من أن تقييم الجهاز الوقائي ليس أكثر من‬
4-5
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Chapter 4: Warning Statements for AC Systems
경고!
¡Advertencia!
이 제품은 전원의 단락(과전류)방지에 대해서 전적으로 건물의 관련 설비에
El sistema debe ser disconnected de todas las fuentes de energía y del cable
eléctrico quitado de los módulos de fuente de alimentación antes de tener acceso
el interior del chasis para instalar o para quitar componentes de sistema.
의존합니다. 보호장치의 정격이 반드시 250V(볼트), 20A(암페어)를 초과하지
않도록 해야 합니다.
Attention
Waarschuwing
Dit product is afhankelijk van de kortsluitbeveiliging (overspanning) van
uw electrische installatie. Controleer of het beveiligde aparaat niet groter
gedimensioneerd is dan 220V, 20A.
Power Disconnection Warning
Warning!
The system must be disconnected from all sources of power and the power cord
removed from the power supply module(s) before accessing the chassis interior to
install or remove system components.
電源切断の警告
システムコンポーネントの取り付けまたは取り外しのために、
シャーシー内部にアクセス
するには、
Le système doit être débranché de toutes les sources de puissance ainsi que de
son cordon d'alimentation secteur avant d'accéder à l'intérieur du chassis pour
installer ou enlever des composants de systéme.
‫אזהרה מפני ניתוק חשמלי‬
!‫אזהרה‬
‫יש לנתק את המערכת מכל מקורות החשמל ויש להסיר את כבל החשמלי מהספק‬
.‫לפני גישה לחלק הפנימי של המארז לצורך התקנת או הסרת רכיבים‬
‫يجب فصم اننظاو من جميع مصادر انطاقت وإزانت سهك انكهرباء من وحدة امداد‬
‫انطاقت قبم‬
‫انىصىل إنى انمناطق انداخهيت نههيكم نتثبيج أو إزانت مكىناث الجهاز‬
システムの電源はすべてのソースから切断され、電源コードは電源モジュールから取り
外す必要があります。
경고!
警告
시스템에 부품들을 장착하거나 제거하기 위해서는 섀시 내부에 접근하기 전에
반드시 전원 공급장치로부터 연결되어있는 모든 전원과 전기코드를 분리해주어야
합니다.
在你打开机箱并安装或移除内部器件前,必须将系统完全断电,并移除电源线。
Waarschuwing
警告
在您打開機殼安裝或移除內部元件前,必須將系統完全斷電,並移除電源線。
Warnung
Voordat u toegang neemt tot het binnenwerk van de behuizing voor het installeren
of verwijderen van systeem onderdelen, dient u alle spanningsbronnen en alle
stroomkabels aangesloten op de voeding(en) van de behuizing te verwijderen
Das System muss von allen Quellen der Energie und vom Netzanschlusskabel
getrennt sein, das von den Spg.Versorgungsteilmodulen entfernt wird, bevor es
auf den Chassisinnenraum zurückgreift, um Systemsbestandteile anzubringen oder
zu entfernen.
4-6
4-7
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Equipment Installation
Chapter 4: Warning Statements for AC Systems
Waarschuwing
Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door
geschoold en gekwalificeerd personeel.
Warning!
Only trained and qualified personnel should be allowed to install, replace, or service
this equipment.
Restricted Area
Warning!
機器の設置
トレーニングを受け認定された人だけがこの装置の設置、交換、
またはサービスを許可
されています。
警告
只有经过培训且具有资格的人员才能进行此设备的安装、更换和维修。
This unit is intended for installation in restricted access areas. A restricted access
area can be accessed only through the use of a special tool, lock and key, or other
means of security. (This warning does not apply to workstations).
アクセス制限区域
このユニットは、
アクセス制限区域に設置されることを想定しています。
警告
只有經過受訓且具資格人員才可安裝、更換與維修此設備。
アクセス制限区域は、特別なツール、鍵と錠前、その他のセキュリティの手段を用いての
み出入りが可能です。
Warnung
警告
此部件应安装在限制进出的场所,限制进出的场所指只能通过使用特殊工具、锁和
钥匙或其它安全手段进出的场所。
Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem,
qualifiziertem Personal gestattet werden.
¡Advertencia!
Solamente el personal calificado debe instalar, reemplazar o utilizar este equipo.
警告
此裝置僅限安裝於進出管制區域,進出管制區域係指僅能以特殊工具、鎖頭及鑰匙
或其他安全方式才能進入的區域。
Warnung
Attention
Il est vivement recommandé de confier l'installation, le remplacement et la
maintenance de ces équipements à des personnels qualifiés et expérimentés.
!‫אזהרה‬
.‫ להחליף את הציוד או לתת שירות עבור הציוד‬,‫צוות מוסמך בלבד רשאי להתקין‬
‫يجب أن يسمح فقط للمىظفيه المؤهليه والمدربيه لتزكيب واستبدال أو خدمة هذا الجهاس‬
경고!
Diese Einheit ist zur Installation in Bereichen mit beschränktem Zutritt vorgesehen.
Der Zutritt zu derartigen Bereichen ist nur mit einem Spezialwerkzeug, Schloss und
Schlüssel oder einer sonstigen Sicherheitsvorkehrung möglich.
¡Advertencia!
Esta unidad ha sido diseñada para instalación en áreas de acceso restringido.
Sólo puede obtenerse acceso a una de estas áreas mediante la utilización de una
herramienta especial, cerradura con llave u otro medio de seguridad.
Attention
훈련을 받고 공인된 기술자만이 이 장비의 설치, 교체 또는 서비스를 수행할 수
있습니다.
4-8
Cet appareil doit être installée dans des zones d'accès réservés. L'accès à une
zone d'accès réservé n'est possible qu'en utilisant un outil spécial, un mécanisme
de verrouillage et une clé, ou tout autre moyen de sécurité.
4-9
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
‫אזור עם גישה מוגבלת‬
!‫אזהרה‬
‫ הגישה ניתנת בעזרת‬.‫יש להתקין את היחידה באזורים שיש בהם הגבלת גישה‬
.)'‫ מנעול וכד‬,‫כלי אבטחה בלבד (מפתח‬
Chapter 4: Warning Statements for AC Systems
Warnung
Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die
Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp.
Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.
Attention
. ‫تم تخصيص هذه انىحذة نتركُبها فٍ مناطق محظورة‬
،‫َمكن انىصىل إنً منطقت محظورة فقط من خالل استخذاو أداة خاصت‬
‫قفم ومفتاح أو أٌ وسُهت أخري نالمألما‬
경고!
Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer
que par une pile de type semblable ou équivalent, recommandée par le fabricant.
Jeter les piles usagées conformément aux instructions du fabricant.
¡Advertencia!
이 장치는 접근이 제한된 구역에 설치하도록 되어있습니다. 특수도구, 잠금 장치 및
키, 또는 기타 보안 수단을 통해서만 접근 제한 구역에 들어갈 수 있습니다.
Waarschuwing
Dit apparaat is bedoeld voor installatie in gebieden met een beperkte toegang.
Toegang tot dergelijke gebieden kunnen alleen verkregen worden door gebruik te
maken van speciaal gereedschap, slot en sleutel of andere veiligheidsmaatregelen.
Existe peligro de explosión si la batería se reemplaza de manera incorrecta.
Reemplazar la batería exclusivamente con el mismo tipo o el equivalente
recomendado por el fabricante. Desechar las baterías gastadas según las
instrucciones del fabricante.
!‫אזהרה‬
‫ יש להחליף‬.‫קיימת סכנת פיצוץ של הסוללה במידה והוחלפה בדרך לא תקינה‬
.‫את הסוללה בסוג התואם מחברת יצרן מומלצת‬
Battery Handling
.‫סילוק הסוללות המשומשות יש לבצע לפי הוראות היצרן‬
Warning!
There is the danger of explosion if the battery is replaced incorrectly. Replace the
battery only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's instructions
‫هناك خطر من انفجار في حالة اسحبذال البطارية بطريقة غير صحيحة فعليل‬
‫اسحبذال البطارية‬
‫فقط بنفس النىع أو ما يعادلها مما أوصث به الشرمة المصنعة‬
‫جخلص من البطاريات المسحعملة وفقا لحعليمات الشرمة الصانعة‬
電池の取り扱い
電池交換が正しく行われなかった場合、破裂の危険性があります。交換する電池はメー
カーが推奨する型、
または同等のものを使用下さい。使用済電池は製造元の指示に従
って処分して下さい。
警告
电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更
换原有电池。请按制造商的说明处理废旧电池。
경고!
배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와
동일하거나 제조사에서 권장하는 동등한 종류의 배터리로만 교체해야 합니다.
제조사의 안내에 따라 사용된 배터리를 처리하여 주십시오.
Waarschuwing
警告
電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有
電池。請按照製造商的說明指示處理廢棄舊電池。
4-10
Er is ontploffingsgevaar indien de batterij verkeerd vervangen wordt. Vervang de
batterij slechts met hetzelfde of een equivalent type die door de fabrikant aanbevolen
wordt. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften afgevoerd
te worden.
4-11
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Chapter 4: Warning Statements for AC Systems
Redundant Power Supplies
경고!
Warning!
This unit might have more than one power supply connection. All connections must
be removed to de-energize the unit.
冗長電源装置
このユニットは複数の電源装置が接続されている場合があります。
ユニットの電源を切るためには、すべての接続を取り外さなければなりません。
警告
此部件连接的电源可能不止一个,必须将所有电源断开才能停止给该部件供电。
警告
此裝置連接的電源可能不只一個,必須切斷所有電源才能停止對該裝置的供電。
.‫قد يكون لهذا الجهاز عدة اتصاالت بوحدات امداد الطاقة‬
‫يجب إزالة كافة االتصاالت لعسل الوحدة عن الكهرباء‬
이 장치에는 한 개 이상의 전원 공급 단자가 연결되어 있을 수 있습니다. 이 장치에
전원을 차단하기 위해서는 모든 연결 단자를 제거해야만 합니다.
Waarschuwing
Deze eenheid kan meer dan één stroomtoevoeraansluiting bevatten. Alle
aansluitingen dienen verwijderd te worden om het apparaat stroomloos te maken.
Backplane Voltage
Warning!
Hazardous voltage or energy is present on the backplane when the system is
operating. Use caution when servicing.
バックプレーンの電圧
Warnung
Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass
der Einheit kein trom zugeführt wird, müssen alle Verbindungen entfernt werden.
¡Advertencia!
Puede que esta unidad tenga más de una conexión para fuentes de alimentación.
Para cortar por completo el suministro de energía, deben desconectarse todas las
conexiones.
システムの稼働中は危険な電圧または電力が、バックプレーン上にかかっています。
修理する際には注意ください。
警告
当系统正在进行时,背板上有很危险的电压或能量,进行维修时务必小心。
警告
當系統正在進行時,背板上有危險的電壓或能量,進行維修時務必小心。
Attention
Warnung
Cette unité peut avoir plus d'une connexion d'alimentation. Pour supprimer toute
tension et tout courant électrique de l'unité, toutes les connexions d'alimentation
doivent être débranchées.
Wenn das System in Betrieb ist, treten auf der Rückwandplatine gefährliche
Spannungen oder Energien auf. Vorsicht bei der Wartung.
‫אם קיים יותר מספק אחד‬
!‫אזהרה‬
‫ יש להסיר את כל החיבורים על מנת לרוקן‬.‫ליחדה יש יותר מחיבור אחד של ספק‬
.‫את היחידה‬
¡Advertencia!
Cuando el sistema está en funcionamiento, el voltaje del plano trasero es peligroso.
Tenga cuidado cuando lo revise.
Attention
Lorsque le système est en fonctionnement, des tensions électriques circulent sur
le fond de panier. Prendre des précautions lors de la maintenance.
4-12
4-13
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Chapter 4: Warning Statements for AC Systems
‫מתח בפנל האחורי‬
!‫אזהרה‬
‫ יש להיזהר במהלך‬.‫קיימת סכנת מתח בפנל האחורי בזמן תפעול המערכת‬
.‫העבודה‬
‫هناك خطز مه التيار الكهزبائي أوالطاقة المىجىدة على اللىحة‬
‫عندما يكىن النظام يعمل كه حذرا عند خدمة هذا الجهاس‬
Attention
L'équipement doit être installé conformément aux normes électriques nationales
et locales.
‫תיאום חוקי החשמל הארצי‬
!‫אזהרה‬
.‫התקנת הציוד חייבת להיות תואמת לחוקי החשמל המקומיים והארציים‬
‫تركيب المعدات الكهربائية يجب أن يمتثل للقىاويه المحلية والىطىية المتعلقة‬
‫بالكهرباء‬
경고!
시스템이 동작 중일 때 후면판 (Backplane)에는 위험한 전압이나 에너지가 발생
합니다. 서비스 작업 시 주의하십시오.
경고!
현 지역 및 국가의 전기 규정에 따라 장비를 설치해야 합니다.
Waarschuwing
Een gevaarlijke spanning of energie is aanwezig op de backplane wanneer het
systeem in gebruik is. Voorzichtigheid is geboden tijdens het onderhoud.
Comply with Local and National Electrical Codes
Warning!
Installation of the equipment must comply with local and national electrical codes.
地方および国の電気規格に準拠
機器の取り付けはその地方および国の電気規格に準拠する必要があります。
警告
设备安装必须符合本地与本国电气法规。
Waarschuwing
Bij installatie van de apparatuur moet worden voldaan aan de lokale en nationale
elektriciteitsvoorschriften.
Product Disposal
Warning!
Ultimate disposal of this product should be handled according to all national laws
and regulations.
製品の廃棄
この製品を廃棄処分する場合、国の関係する全ての法律・条例に従い処理する必要が
あります。
警告
設備安裝必須符合本地與本國電氣法規。
Warnung
警告
本产品的废弃处理应根据所有国家的法律和规章进行。
Die Installation der Geräte muss den Sicherheitsstandards entsprechen.
警告
本產品的廢棄處理應根據所有國家的法律和規章進行。
¡Advertencia!
Warnung
La instalacion del equipo debe cumplir con las normas de electricidad locales y
nacionales.
Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen
des Landes erfolgen.
4-14
4-15
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Chapter 4: Warning Statements for AC Systems
¡Advertencia!
Al deshacerse por completo de este producto debe seguir todas las leyes y
reglamentos nacionales.
警告
當您從機架移除風扇裝置,風扇可能仍在轉動。小心不要將手指、螺絲起子和其他
物品太靠近風扇。
Warnung
Attention
La mise au rebut ou le recyclage de ce produit sont généralement soumis à des
lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de
l'organisme compétent.
‫סילוק המוצר‬
!‫אזהרה‬
.‫סילוק סופי של מוצר זה חייב להיות בהתאם להנחיות וחוקי המדינה‬
‫عند التخلص النهائي من هذا المنتج ينبغي التعامل معه وفقا لجميع القىانين واللىائح الىطنية‬
경고!
이 제품은 해당 국가의 관련 법규 및 규정에 따라 폐기되어야 합니다.
Waarschuwing
De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming
met alle nationale wetten en reglementen.
Hot Swap Fan Warning
Die Lüfter drehen sich u. U. noch, wenn die Lüfterbaugruppe aus dem Chassis
genommen wird. Halten Sie Finger, Schraubendreher und andere Gegenstände
von den Öffnungen des Lüftergehäuses entfernt.
¡Advertencia!
Los ventiladores podran dar vuelta cuando usted quite ell montaje del ventilador
del chasis. Mandtenga los dedos, los destornilladores y todos los objetos lejos de
las aberturas del ventilador
Attention
Il est possible que les ventilateurs soient toujours en rotation lorsque vous retirerez
le bloc ventilateur du châssis. Prenez garde à ce que doigts, tournevis et autres
objets soient éloignés du logement du bloc ventilateur.
!‫אזהרה‬
‫ יש‬.‫ יתכן והמאווררים עדיין עובדים‬,‫כאשר מסירים את חלקי המאוורר מהמארז‬
‫להרחיק למרחק בטוח את האצבעות וכלי עבודה שונים מהפתחים בתוך המאוורר‬
‫مه انممكه أن انمراوح ال تسال تدورعند إزانة كتهة انمروحة مه انهيكم يجب إبقاء‬
‫األصابع ومفكات انبراغي‬
.‫وغيرها مه األشياء بعيدا عه انفتحات في كتهة انمروحة‬
Warning!
The fans might still be turning when you remove the fan assembly from the chassis.
Keep fingers, screwdrivers, and other objects away from the openings in the fan
assembly's housing.
ファン・ホットスワップの警告
シャーシから冷却ファン装置を取り外した際、
ファンがまだ回転している可能性がありま
す。ファンの開口部に、指、
ドライバー、およびその他のものを近づけないで下さい。
警告
当您从机架移除风扇装置,风扇可能仍在转动。小心不要将手指、螺丝起子和其他
物品太靠近风扇
4-16
경고!
섀시로부터 팬 조립품을 제거할 때 팬은 여전히 회전하고 있을 수 있습니다. 팬
조림품 외관의 열려있는 부분들로부터 손가락 및 스크류드라이버, 다른 물체들이
가까이 하지 않도록 배치해 주십시오.
Waarschuwing
Het is mogelijk dat de ventilator nog draait tijdens het verwijderen van het
ventilatorsamenstel uit het chassis. Houd uw vingers, schroevendraaiers
en eventuele andere voorwerpen uit de buurt van de openingen in de
ventilatorbehuizing.
4-17
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Power Cable and AC Adapter
Chapter 4: Warning Statements for AC Systems
Attention
Lors de l'installation du produit, utilisez les bables de connection fournis ou désigné.
L'utilisation d'autres cables et adaptateurs peut provoquer un dysfonctionnement
Warning!
When installing the product, use the provided or designated connection cables,
power cables and AC adaptors. Using any other cables and adaptors could cause
a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the
use of UL or CSA -certified cables (that have UL/CSA shown on the code) for any
other electrical devices than products designated by Supermicro only.
電源コードとACアダプター
製品を設置する場合、提供または指定された接続ケーブル、電源コードとACアダプター
を使用下さい。他のケーブルやアダプタを使用すると故障や火災の原因になることがあ
ります。電気用品安全法は、ULまたはCSA認定のケーブル(UL/CSEマークがコードに表
記)を Supermicroが指定する製品以外に使用することを禁止しています。
警告
安装此产品时,请使用本身提供的或指定的连接线,电源线和电源适配器.使用其它线
材或适配器可能会引起故障或火灾。除了Supermicro所指定的产品,电气用品和材
料安全法律规定禁止使用未经UL或CSA认证的线材。(线材上会显示UL/CSA符号)。
警告
安裝此產品時,請使用本身提供的或指定的連接線,電源線和電源適配器.使用其它線
材或適配器可能會引起故障或火災。除了Supermicro所指定的產品,電氣用品和材
料安全法律規定禁止使用未經UL或CSA認證的線材。(線材上會顯示UL/CSA符號)。
Warnung
Bei der Installation des Produkts, die zur Verfügung gestellten oder benannt
Anschlusskabel, Stromkabel und Netzteile. Verwendung anderer Kabel und Adapter
kann zu einer Fehlfunktion oder ein Brand entstehen. Elektrische Geräte und
Material Safety Law verbietet die Verwendung von UL-oder CSA-zertifizierte Kabel,
UL oder CSA auf der Code für alle anderen elektrischen Geräte als Produkte von
Supermicro nur bezeichnet gezeigt haben.
¡Advertencia!
Al instalar el producto, utilice los cables de conexión previstos o designados, los
cables y adaptadores de CA. La utilización de otros cables y adaptadores podría
ocasionar un mal funcionamiento o un incendio. Aparatos Eléctricos y la Ley de
Seguridad del Material prohíbe el uso de UL o CSA cables certificados que tienen
UL o CSA se muestra en el código de otros dispositivos eléctricos que los productos
designados por Supermicro solamente.
4-18
ou un incendie. Appareils électroménagers et de loi sur la sécurité Matériel interdit
l'utilisation de UL ou CSA câbles certifiés qui ont UL ou CSA indiqué sur le code
pour tous les autres appareils électriques que les produits désignés par Supermicro
seulement.
AC
‫חשמליים ומתאמי‬
!‫אזהרה‬
‫ אשר‬AC ‫ ספקים ומתאמים‬,‫ יש להשתמש בכבלים‬,‫כאשר מתקינים את המוצר‬
‫ שימוש בכל כבל או מתאם אחר יכול לגרום לתקלה או‬.‫נועדו וסופקו לשם כך‬
‫ קיים איסור‬,‫ על פי חוקי שימוש במכשירי חשמל וחוקי בטיחות‬.‫קצר חשמלי‬
‫ (כשאר מופיע עליהם קוד של‬CSA -‫ או ב‬UL -‫להשתמש בכבלים המוסמכים ב‬
.‫) עבור כל מוצר חשמלי אחר שלא צוין על ידי סופרקמיקרו בלבד‬UL/CSA
‫والكابالث الكهربائيت‬،‫عىذ تركيب الجهاز يجب استخذام كابالث التىصيل‬
‫ومحىالث التيار المتردد‬
.‫ أن استخذام أي كابالث ومحىالث أخري يتسبب في حذوث عطل أو حريق‬. ‫التي‬
‫تم تىفيرها لك مع المىتج‬
UL ‫ أو‬CSA ‫األجهسة الكهربائيت ومىاد قاوىن السالمت يحظر استخذام الكابالث‬
‫معتمذة مه قبل‬
Supermicro ‫ألي أجهسة كهربائيت أخري غير المىتجاث المعيىت مه قبل‬
(UL/CSA ‫)التي تحمل عالمت‬
경고!
제품을 설치할 때에는 제공되거나 지정된 연결케이블과 전원케이블, AC어댑터를
사용해야 합니다. 그 밖의 다른 케이블들이나 어댑터들은 고장 또는 화재의 원인이
될 수 있습니다. 전기용품안전법 (Electrical Appliance and Material Safety
Law)은 슈퍼마이크로에서 지정한 제품들 외에는 그 밖의 다른 전기 장치들을
위한 UL또는 CSA에서 인증한 케이블(전선 위에 UL/CSA가 표시)들의 사용을
금지합니다.
Waarschuwing
Bij het installeren van het product, gebruik de meegeleverde of aangewezen kabels,
stroomkabels en adapters. Het gebruik van andere kabels en adapters kan leiden
tot een storing of een brand. Elektrisch apparaat en veiligheidsinformatiebladen wet
verbiedt het gebruik van UL of CSA gecertificeerde kabels die UL of CSA die op
de code voor andere elektrische apparaten dan de producten die door Supermicro
alleen.
4-19
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Notes
4-20
Chapter 5: Advanced Serverboard Setup
Chapter 5
Advanced Serverboard Setup
This chapter is provided as a reference and describes the data and power cable
connections and add-on cards. All serverboard jumpers and connections are also
described. A layout and quick reference chart are included in this chapter for your
reference. Remember to completely close the chassis when you have finished
working with the serverboard to better cool and protect the system.
5-1 Handling the Serverboard
Electrostatic Discharge (ESD) can damage electronic com­ponents. To prevent damage to any printed circuit boards (PCBs), it is important to handle them very carefully
(see previous chapter). To prevent the serverboard from bending, keep one hand
under the center of the board to support it when handling. The following measures
are generally sufficient to protect your equipment from electric static discharge.
Precautions
•Use
a grounded wrist strap designed to prevent Electrostatic Discharge
(ESD).
•Touch a grounded metal object before removing any board from its antistatic
bag.
•Handle a board by its edges only; do not touch its components, peripheral chips,
memory modules or gold contacts.
•When handling chips or modules, avoid touching their pins.
•Put the serverboard, add-on cards and peripherals back into their antistatic
bags when not in use.
•For grounding purposes, make sure your computer chassis provides excellent
conductivity between the power supply, the case, the mounting fasteners and
the serverboard.
5-1
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Chapter 5: Advanced Serverboard Setup
5-2 Connecting Cables
Figure 5-1. Control Panel Header Pins
Several cables need to be connected to the serverboard. These include the data
1
cables for the peripherals and control panel and the power cables.
Ground
Reset Button
Ground
Connecting Data Cables
The cables used to transfer data from the peripheral devices have been carefully
routed to prevent them from blocking the flow of cooling air that moves through
the system from front to back. If you need to disconnect any of these cables, you
should take care to keep them routed as they were originally after reconnecting
them (make sure the red wires connect to the pin 1 locations). See the layout on
page 5-10 for connector locations.
2
Power Button
3.3V
Power Fail LED
UID LED
OH/Fan Fail/
PWR Fail LED)
NIC2 Activity LED
NIC2 Link LED
NIC1 Activity LED
NIC1 Link LED
UID Switch
HDD LED
FP PWRLED
3.3 V
X
X
Connecting Power Cables
The X10DRH-iT has a 24-pin primary power supply connector (J24) for connection
to the ATX power supply. In addition, there are two 8-pin 12V processor power connectors (JPWR1 and JPWR2) that must be connected to your power supply. See
Section 5-9 for power connector pin definitions.
Ground
NMI
19
20
5-3 Rear I/O Ports
See Figure 5-2 below for the locations of the various I/O ports.
Connecting the Control Panel
JF1 contains header pins for various front control panel connectors. See Figure 5-1
for the pin locations of the various front control panel buttons and LED indicators.
Figure 5-2. Rear I/O Ports
All JF1 wires have been bundled into a single cable to simplify this connection. Make
sure the red wire plugs into pin 1 as marked on the board. The other end connects
to the Control Panel PCB board, located just behind the system status LEDs on
the chassis. See Chapter 5 for details and pin descriptions.
2
3
4
18
7
5
6
9
1
Rear I/O Ports
1
COM Port 1
6
USB Port 4
2
Dedicated IPMI LAN
7
TLAN Port 1
3
USB Port 1
8
TLAN Port 2
4
USB Port 0
9
VGA Port
5
USB Port 5
Note: a UID (Unit Identifier) button and LED is located to the right of the VGA port
(not pictured).
5-2
5-3
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Chapter 5: Advanced Serverboard Setup
5-4 Installing the Processor and Heatsink
Warning: When handling the processor package, avoid placing direct pressure on the
label area of the fan.
Notes:
Always connect the power cord last and always remove it before adding, removing or changing any hardware components. Make sure that you install the
processor into the CPU socket before you install the CPU heatsink.
•
•If you buy a CPU separately, make sure that you use an Intel-certified multidirectional heatsink only.
•Make sure to install the serverboard into the chassis before you install the CPU
heatsinks.
•When receiving a serverboard without a processor pre-installed, make sure that
the plastic CPU socket cap is in place and none of the socket pins are bent;
otherwise, contact your retailer immediately.
•Refer to the Supermicro web site for updates on CPU support.
Installing an LGA2011 Processor
Press down on the lever labeled
'Close 1st'
1. There are two levers on the
LGA2011 socket. First press and
release the load lever labeled
'Open 1st'.
WA
R
NI
OP
2. Press the second load lever
labeled 'Close 1st' to release the
load plate from its locked position.
EN
NG
3. With the lever labeled 'Close 1st'
fully retracted, gently push down
on the 'Open 1st' lever to open the
load plate. Lift the load plate to
open it completely.
NI
OP
EN
NG
!
1st
Gently push
down to pop
the load plate
open.
4. Using your thumb and the index
finger, remove the 'WARNING'
plastic cap from the socket.
5. Use your thumb and index finger
to hold the CPU by its edges. Align
the CPU keys, which are semicircle cutouts, against the socket
keys.
WA
R
NI
NG
!
6. Once they are aligned, carefully
lower the CPU straight down into
the socket. (Do not drop the CPU
on the socket. Do not move the
CPU horizontally or vertically and
do not rub the CPU against any
pins of the socket, which may
damage the CPU or the socket.)
Socket Keys
!
1st
CPU Keys
Pull lever away
from the socket
WA
R
NI
OP
EN
5-4
WA
R
NG
!
1st
5-5
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Chapter 5: Advanced Serverboard Setup
Warning: You can only install the CPU to the socket in one direction. Make sure that
the CPU is properly inserted into the socket before closing the load plate. If it doesn't
close properly, do not force it as it may damage your CPU. Instead, open the load
plate again and double-check that the CPU is aligned properly.
Installing a Passive CPU Heatsink
1. Do not apply any thermal grease to the heatsink or the CPU die. The required
amount has already been applied.
2. Place the heatsink on top of the CPU so that the four mounting holes are
aligned with those on the serverboard and the heatsink bracket underneath.
7. With the CPU in the socket, inspect the four corners of the CPU
to make sure that they are flush
with the socket.
8. Close the load plate. Lock the
lever labeled 'Close 1st', then lock
the lever labeled 'Open 1st'. Use
your thumb to gently push the
load levers down until the lever
locks.
3. Screw in two diagonal screws (i.e., the #1 and the #2 screws) until just snug
(do not over-tighten the screws to avoid possible damage to the CPU.)
Gently close
the load plate.
4. Finish the installation by fully tightening all four screws.
Figure 5-3. Installing a Heatsink
Screw#1
Screw#4
Screw#3
Screw#2
Push down and lock the
level labeled 'Close 1st'.
OP
EN
1st
Removing the Heatsink
Warning: We do not recommend that the CPU or the heatsink be removed. However,
if you do need to uninstall the heatsink, please follow the instructions below to uninstall
the heatsink to prevent damage done to the CPU or the CPU socket.
Lever Lock
1. Unscrew the heatsink screws from the serverboard in the sequence as shown
in the illustration above.
OP
EN
2. Gently wriggle the heatsink to loosen it from the CPU. (Do not use excessive
force when wriggling the heatsink!)
1st
Push down
and lock the
lever labeled
'Open 1st'.
3. Once the heatsink is loose, remove it from the CPU.
4. Remove the used thermal grease and clean the surface of the CPU and the
heatsink, Reapply the proper amount of thermal grease on the surface before
reinstalling the heatsink.
Warning: Do not reuse old thermal grease!
5-6
5-7
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
5-5 Installing Memory
Chapter 5: Advanced Serverboard Setup
Processor & Memory Module Population Configuration
For the memory to work properly, follow the tables below for correct installation.
Caution: Exercise extreme care when installing or removing DIMM modules to prevent
Processors and their Corresponding Memory Modules
any possible damage.
CPU#
Memory Support
The X10DRH-iT has 16 DIMM slots that can support up to 2 TB of Load Reduced
(LRDIMM) or 1 TB of Registered (RDIMM) ECC DDR4-2400/2133/1866/1600
memory. For best performance, install pairs of memory modules of the same type
and speed. Please refer to our website for any updates to supported memory. All
channels will run at the fastest common frequency.
DIMM Installation
Installing Memory Modules
1. Insert the desired number of DIMMs into the memory slots starting with P1DIMMA1. See the Memory Installation Tables on the following pages.
2. Insert each DIMM module vertically into its slot. Pay attention to the notch
along the bottom of the module to avoid installing incorrectly (see Figure 5-3).
3. Use your thumbs to gently press down on both ends of the DIMM module
until it snaps into place in the slot. Repeat for all modules.
4. Press the release tabs to the locked positions to secure the DIMM module
into the slot.
Figure 5-4. DIMM Installation
Corresponding DIMM Modules
CPU 1
P1DIMMA1
P1DIMMB1
P1DIMMC1
P1DIMMD1
P1DIMMA2
P1DIMMB2
P1DIMMC2
P1DIMMD2
CPU2
P2DIMME1
P2DIMMF1
P2DIMMG1
P2DIMMH1
P2DIMME2
P2DIMM F2
P2DIMMG2
P2DIMMH2
Processor and Memory Module Population for Optimal Performance
Number of
CPUs+DIMMs
CPU and Memory Population Configuration Table
(For memory to work properly, please follow this table.)
1 CPU &
2 DIMMs
CPU1
P1-DIMMA1/P1-DIMMB1
1 CPU &
4 DIMMs
CPU1
P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1
1 CPU &
6 or 8 DIMMs
CPU1
P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1 + any pair of P1-DIMMA2/P1DIMMB2/P1-DIMMC2/P1-DIMMD2 slots
2 CPUs &
4 DIMMs
CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1, P2-DIMME1/P2-DIMMF1
2 CPUs &
6 DIMMs
CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1
2 CPUs &
8 DIMMs
CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2DIMMG1/P2-DIMMH1
2 CPUs &
10~16 DIMMs
CPU1/CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2DIMMG1/P2-DIMMH1 + any pair of P1, P2 DIMM slots
2 CPUs &
16 DIMMs
CPU1/CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-DIMMG1/P2-DIMMH1,P1-DIMMA2/P1-DIMMB2/P1-DIMMC2/P1-DIMMD2, P2-DIMME2/
P2-DIMMF2/P2-DIMMG2/P2-DIMMH2
Note: see layout diagrams on following page, which display the order of populating DIMMs.
Release Tab
Socket Key
Release Tab
5-8
5-9
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
1 CPU, 2 DIMMs
1 CPU, 4 DIMMs
Chapter 5: Advanced Serverboard Setup
1 CPU, 6 or 8 DIMMs
Populating RDIMM/LRDIMM DDR4 Memory Modules
Speed (MT/s); Voltage (V); Slots per Channel (SPC) and
DIMMs per Channel (DPC)
BAR CODE
MAC CODE
BAR CODE
MAC CODE
X10DRH-C/i(T)
Rev. 1.00
BIOS
LICENSE
BIOS
LICENSE
X10DRH-C/i(T)
Rev. 1.00
BAR CODE
MAC CODE
BIOS
Type
X10DRH-C/i(T)
Rev. 1.00
7LICENSE8
6
5
Ranks
Per DIMM
and Data
Width
BAR CODE
MAC CODE
2 CPUs, 6 DIMMs
BAR CODE
MAC CODE
X10DRH-C/i(T)
Rev. 1.00
BIOS
LICENSE
BIOS
LICENSE
X10DRH-C/i(T)
Rev. 1.00
2 CPUs, 8 DIMMs
BAR CODE
MAC CODE
BIOS
LICENSE
2 Slots per Channel
1 DPC
2 DPC
E5-2600 V3
E5-2600 V4
E5-2600 V3
E5-2600 V4
4 Gb
8 Gb
1.2 V
1.2 V
1.2 V
1.2 V
SRx4
8 GB
16 GB
2133
2400
1866
2133
RDIMM
SRx8
4 GB
8 GB
2133
2400
1866
2133
RDIMM
DRx8
8 GB
16 GB
2133
2400
1866
2133
RDIMM
DRx4
16 GB
32 GB
2133
2400
1866
2133
LRDIMM
QRx4
32 GB
64 GB
2133
2400
2133
2400
LRDIMM 3DS
8Rx4
64 GB
128 GB
2133
2400
2133
2400
RDIMM
2 CPUs, 4 DIMMs
DIMM Capacity
(GB)
5-6 Adding PCI Expansion Cards
X10DRH-C/i(T)
Rev. 1.00
The 6048R-E1CR24H can accommodate up to five PCI expansion cards in the PCI
slots on the serverboard. Note that two of the seven PCI slots on the serverboard
are already populated with the Hardware RAID controller card and the JBOD expansion card.
Installing an Add-on Card
2 CPUs, 10-16 DIMMs
13 14
BAR CODE
MAC CODE
BIOS
11LICENSE
12
1. Begin by removing the shield for the PCI slot you wish to populate. Make sure
that the card you are installing is supported by the slot (see table below).
16 15
2. Fully seat the card into the slot, pushing down with your thumbs evenly on
both sides of the card.
X10DRH-C/i(T)
Rev. 1.00
10 9
3. Finish by using a screw to secure the top of the card shield to the chassis.
The PCI slot shields protect the serverboard and its components from EMI
and aid in proper ventilation, so make sure there is always a shield covering
each unused slot.
5-10
Expansion Slot
Description
Slot1 (CPU1)
JBOD Expansion
Slot2 (CPU1)
HW RAID Controller
Slot3 (CPU1)
PCI-Express 3.0 x8 slot from CPU1
Slot4 (CPU2)
PCI-Express 3.0 x16 slot from CPU2
Slot5 (CPU2)
PCI-Express 3.0 x8 slot from CPU2
Slot6 (CPU2)
PCI-Express 3.0 x8 slot from CPU2
Slot7 (CPU2)
PCI-Express 3.0 x8 slot from CPU2
5-11
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Chapter 5: Advanced Serverboard Setup
5-7 Serverboard Details
X10DRH-iT Quick Reference
Figure 5-5. X10DRH-iT Layout
LE1
USB0/1
LAN CTRL
USB4/5
(3.0)
FAN5
CPU2 SLOT7 PCI-E 3.0 X8
CPU2 SLOT6 PCI-E 3.0 X8
CPU2 SLOT5 PCI-E 3.0 X8
CPU2 SLOT4 PCI-E 3.0 X16
CPU1 SLOT3 PCI-E 3.0 X8
Controller Card
USB2/3 I-SATA0 I-SATA2
(2.0)
LEDM1
CPU1 SLOT2 PCI-E 3.0 X8
COM1
CPU2
CLOSE 1st
OPEN 1st
P2 DIMMF2
P2 DIMMF1
P2 DIMME2
P2 DIMME1
BAR CODE
Battery MAC CODE
BIOS
Rev. 1.00
BIOS
LICENSE
PCH
S-SATA
JPI2C1
JPWR1 PWR I2C
P1 DIMMD2
P1 DIMMD1
P1 DIMMC2
P1 DIMMC1
I-SGPIO2
I-SGPIO1
USB6
(3.0)
P1 DIMMA1
P1 DIMMA2
P1 DIMMB1
P1 DIMMB2
I-SATA4
X10DRH-C/i(T)
BT1
JI2C2
JPME2
J23
JI2C1
CPU1 SLOT1 PCI-E 3.0 X8
JBR1
JBOD ExpansionPort
I-SATA5
I-SATA1 I-SATA3 USB7/8
(3.0)
JPG1
IPMI_LAN P2 DIMMG1
P2 DIMMG2
P2 DIMMH1
P2 DIMMH2
JTPM1
TPM/PORT80 JPL1 JPB1 COM2
JIPMB1
LAN1
VGA
FAN6
BMC
LAN2
UID
CPU1
CLOSE 1st
LEDS6
LEDS5
JBT1
JPWR2
DS13
TFM
SAS0-3 SAS4-7
FAN1
FAN2
FAN3
FANA
FAN4
JOH1
JS1
JL1
JS39
JSTBY1
JD1
LE2
FANB
SP1
JF1
LSI 3108
SAS CTRL
J24
JPS7
JPS1 JWD1
OPEN 1st
Notes
Jumper
Description
Default Setting
JBT1
Clear CMOS/Reset BIOS Configuration
See Section 5-9
JI2C1/JI2C2
SMB to PCI-E Slots
Pins 2-3 (Disabled)
JPB1
BMC Enable/Disable
Pins 1-2 (Enabled)
JPG1
VGA Enable/Disable
Pins 1-2 (Enabled)
JPL1
TLAN1/TLAN2 Enable/Disable
Pins 1-2 (Enabled)
JPME2
Manufacture (ME) Mode Select
Pins 1-2 (Normal)
JWD1
Watch Dog Timer
Pins 1-2 (Reset)
Connector
Description
COM1/COM2
Backplane COM Port1/Front accessible COM2 header
FAN1-6,A, B
Fan Headers
J24
24-pin ATX Main Power Connector
JD1
Speaker/Power LED Header
JF1
Front Control Panel Header
JIPMB1
4-pin External BMC I2C Header (for an IPMI card)
JL1
Chassis Intrusion Header
JPI2C1
Power Supply SMBbus I2C Header
JPWR1/JPWR2
12V 8-pin Power Connectors
JSTBY1
Standby Power Connector
JTPM1
TPM (Trusted Platform Module)/Port 80 Header
LAN1/LAN2
10G-bit Ethernet (TLAN) Ports
IPMI_LAN
Dedicated IPMI LAN (supported by the ASpeed controller)
I-SATA 0-5
SATA 3.0 Ports (supported by Intel PCH)
S-SATA
SATA 3.0 4-port Vertical Connector (supported by Intel SCU)
(I-)SGPIO1/2
Serial Link General Purpose I/O Headers
UID
UID (Unit Identification) Button
USB 0/1 (2.0)
USB 2.0 Ports (rear I/O)
Jumpers not indicated are for test purposes only.
USB 2/3 (2.0)
USB 2.0 Headers
Note that the PCI slots are enabled when their corresponding processors are installed. "CPU2 Slot 4" indicates that a second CPU must be installed in the CPU2
socket to enable this PCI slot.
USB 4/5 (3.0)
USB 3.0 Ports (rear I/O)
USB 7/8 (3.0)
USB 3.0 Header
USB 6 (3.0)
Type A USB 3.0 Connector
LED
Description
State
Status
LE1
Rear UID LED
Blue: On
Unit Identified
LE2
Onboard PWR LED
On
Power On
LEDM1
BMC Heartbeat LED
Green: Blinking
BMC Normal
" " indicates the position of pin 1.
The 6048R-E1CR24H comes pre-installed with a Hardware RAID controller installed
in PCI-E slot 2 and a JBOD expansion port installed in PCI-E slot 1.
5-12
5-13
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
5-8 Connector Definitions
Chapter 5: Advanced Serverboard Setup
ATX Power 24-pin Connector
Pin Definitions
Pin#
Definition
Power Connectors
13
+3.3V
1
+3.3V
A 24-pin main power supply connector (J24) and two 8-pin CPU power
connectors (JPWR1/JPWR2) must be
connected to the power supplyto provide adequate power to the system.
These power connectors meet the SSI
EPS 12V specification. See the table
on the right for pin definitions.
14
-12V
2
+3.3V
15
COM
3
COM
16
PS_ON
4
+5V
17
COM
5
COM
18
COM
6
+5V
19
COM
7
COM
20
Res (NC)
8
PWR_OK
21
+5V
9
5VSB
22
+5V
10
+12V
23
+5V
11
+12V
24
COM
12
+3.3V
Secondary Power Connector
JPWR1 and JPWR2 must also be
connected to the power supply. See
the table on the right for pin definitions.
Pin #
Definition
+12V 8-pin Power
Pin Definitions
Pins
Definition
1-4
Ground
5-8
+12V
Required Connection
Warning: To provide adequate power supply to the serverboard, be sure to connect
J24 and both JPWR1 and JPWR2 to the power supply. Failure to do so will void
the manufacturer warranty on your power supply and serverboard.
Power Fail LED
PWR Fail LED
Pin Definitions (JF1)
The Power Fail LED connection is
located on pins 5 and 6 of JF1. Refer to the table on the right for pin
definitions.
Definition
5
3.3V
6
PWR Supply Fail
OH/Fan Fail/ PWR Fail/Blue_UID
LED Pin Definitions (JF1)
Overheat, Fan/Power Fail/UID LED
Connect an LED cable to pins 7 and
8 of the front control panel to use the
Overheat/Fan Fail/Power Fail and
UID LED connections. The red LED
on pin 8 provides warnings of overheat, fan failure or power failure. The
blue LED on pin 7 works as the front
panel UID LED indicator. Refer to the
table on the right for pin definitions.
Pin#
Pin#
Definition
7
Blue_UID LED
8
OH/Fan Fail/Power Fail
OH/Fan Fail/PWR Fail
LED Status (Red LED)
State
Definition
Off
Normal
On
Overheat
Flashing
Fan Fail
NIC2 (LAN2) LED
The LED connections for LAN2 are
on pins 9 and 10 of JF1. Attach an
LED cable to display network activity. See the table on the right for pin
definitions.
NIC2 LED
Pin Definitions (JF1)
Pin#
Definition
9
Activity
10
Link
Power Button
The Power On connection is on pins
1 and 2 of JF1. These should be connected to the chassis power button.
Momentarily contacting both pins will
power on/off the system. To turn off
the power when the system is on,
press the button for 4 seconds or
longer. See the table on the right for
pin definitions.
NIC1 (LAN1) LED
Power Button
Pin Definitions (JF1)
Pin#
Definition
1
Power Signal
2
Ground
5-14
NIC1 LED
Pin Definitions (JF1)
Pin#
Definition
11
Activity
12
Link
HDD LED/UID Switch
Reset Button
The Reset Button connection is
located on pins 3 and 4 of JF1 and
attaches to the reset switch on the
computer chassis. See the table on
the right for pin definitions.
The LED connections for LAN1 are
on pins 11 and 12 of JF1. Attach an
LED cable to display network activity. See the table on the right for pin
definitions.
Reset Button
Pin Definitions (JF1)
Pin#
Definition
3
Reset
4
Ground
The HDD LED connection is located
on pins 13 and 14 of JF1. Attach a
cable to pin 14 to show HDD activity
status. Attach a cable to pin 13 to use
UID switch. See the table on the right
for pin definitions.
5-15
HDD LED
Pin Definitions (JF1)
Pin#
Definition
13
UID Switch
14
HD Active
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Power On LED
The Power On LED connector is located on pins 15 and 16 of JF1 (use
JLED for a 3-pin connector). This
connection is used to provide LED
indication of power being supplied to
the system. See the table on the right
for pin definitions.
Chapter 5: Advanced Serverboard Setup
Power LED
Pin Definitions (JF1)
Internal Speaker
Pin#
Definition
The internal speaker, located at SP1,
15
3.3V
16
PWR LED
can be used to provide audible indications for various beep codes. See the
table on the right for pin definitions..
Internal Buzzer (SP1)
Pin Definition
Pin#
Pin 1
Pos. (+)
Beep In
Pin 2
Neg. (-)
Alarm
Speaker
PWR LED Connector
Pin Definitions
Pin Setting
Power LED/Speaker
NMI Button
The non-maskable interrupt button
header is located on pins 19 and 20
of JF1. Refer to the table on the right
for pin definitions.
Definitions
NMI Button
Pin Definitions (JF1)
Pin#
Definition
19
Control
20
Ground
On the JD1 header, pins 1-3 are for
a power LED and pins 4-7 are for the
speaker. Close pins 4-7 with a jumper
to use an external speaker. If you wish
to use the onboard speaker, please
close pins 6-7. See the table on the
right for speaker pin definitions.
JD1_PIN1
2
FP_PWR_LED
3
FP_PWR_LED
Speaker Connector
Pin Definitions
Pin Setting
Fan Headers
There are eight fan headers on the
serverboard, all of which are 4-pin
headers. Pins 1-3 are backward compatible with the traditional 3-pin fans.
(Fan speed control is supported with
4-pin fans only.) See the table on the
right for pin definitions. The onboard
fan speeds are controlled by Thermal
Management (via IPMI).
Fan Header
Pin Definitions
(FAN1-6, FAN A, FAN B)
Pin#
Definition
1
Ground (Black)
2
+12V (Red)
3
Tachometer
4
PWR Modulation
Chassis Intrusion
The Chassis Intrusion header is designated JL1. Attach an appropriate
cable from the chassis to inform you
of a chassis intrusion when the chassis is opened
5-16
Chassis Intrusion
Pin Definitions
Pin#
Definition
1
Intrusion Input
2
Ground
Definition
1
Definition
4
P5V
5
Key
6
R_SPKPIN_N
7
R_SPKPIN
SGPIO Headers
The SGPIO (Serial General Purpose
Input/Output) headers are used to
communicate with the enclosure
management chip on the backplane.
T-SGPIO1/2 support the I-SATA ports
and S-SGPIO1 supports the S-SATA
ports. See the table on the right for
pin definitions.
SGPIO Header
Pin Definitions
Pin#
Definition
Pin
Definition
1
NC
2
NC
3
Ground
4
DATA Out
5
Load
6
Ground
7
Clock
8
NC
NC = No Connection
PWR SMBus Header
Pin Definitions
Power Supply SMBus I2C Header
The power System Management Bus
header at JPI2C1 is used to monitor
the status of the power supply, fan and
system temperature. See the table on
the right for pin definitions.
5-17
Pin#
Definition
1
Clock
2
Data
3
PWR Fail
4
Ground
5
+3.3V
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Chapter 5: Advanced Serverboard Setup
Back Panel USB 0/1 (2.0)
Pin Definitions
Pin# Definition
Pin#
Definition
1
+5V
5
+5V
2
USB_PN1
6
USB_PN0
3
USB_PP1
7
USB_PP0
4
Ground
8
Ground
DOM Power Connectors
Two power connectors for SATA DOM
(Disk On Module) devices are located
at JSD1/JSD2. Connect appropriate
cables here to provide power support
for your DOM devices.
DOM PWR
Pin Definitions
Pin#
Definition
1
+5V
2
Ground
3
Ground
Front Panel USB 2/3 (2.0)
Pin Definitions
Universal Serial Bus (USB)
Two USB 3.0 and two USB 2.0 ports
are located on the rear I/O panel. In
addition, two USB 3.0 headers are
provided on the serverboard for three
front accessible USB 3.0 connections
(USB6, USB 7/8). A USB 2.0 header
is also located on the serverboard
to provide two USB 2.0 connections
(USB 2/3) for front access(cables not
included). See the tables on the right
for pin definitions.
Pin #
Definition
Pin #
Definition
1
+5V
2
+5V
3
USB_PN2
4
USB_PN3
5
USB_PP2
6
USB_PP3
7
Ground
8
Ground
9
Key
10
Ground
Back Panel USB 4/5 (3.0), Front Panel
USB 7/8 (3.0), Type A USB 6 (3.0)
Pin Definitions
Pin#
Description
1
VBUS
2
SSRX-
3
SSRX+
4
Ground
5
SSTX-
6
SSTX+
7
GND_DRAIN
8
D-
9
D+
A System Management Bus header
for IPMI 2.0 is located at JIPMB1.
Connect the appropriate cable here
to use the IPMB I2C connection on
your system.
5-18
The +5V Standby Power header is
located at JSTBY1. See the table
on the right for pin definitions. (You
must also have a card with a Standby
Power connector and a cable to use
this feature.)
Standby PWR
Pin Definitions
Pin#
Definition
1
+5V Standby
2
Ground
3
No Connection
Unit Identifier Switch
The rear UID button and LED are located next to the VGA port. The front
IPMB Header
Pin Definitions
IPMB
Standby Power Header
Pin#
Definition
1
Data
2
Ground
3
Clock
4
No Connection
UID LED is located next to the UID
switch. The front UID switch is located
on pin 13 on JF1 and the front UID
LED is located on pin 7 on JF1. When
you press the front or rear UID switch,
both front and rear UID LEDs will be
turned on. Press the UID switch again
to turn off the LED indicators.These
indicators provide easy identification
of a system unit that may be in need
of service.
UID Switch
Pin#
Definition
1
Ground
2
Ground
3
Button In
4
Button In
UID LED
Status
Color/State Status
Blue: On
Unit Identified
Note: UID can also be triggered via IPMI. For more information on IPMI, please
refer to the IPMI User's Guide posted on our website at http://www.supermicro.com.
5-19
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Chapter 5: Advanced Serverboard Setup
5-9 Jumper Settings
TPM/Port 80 Header
Pin Definitions
Pin #
TPM Header/Port 80
A Trusted Platform Module/Port 80
header is located at JTPM1 to provide
TPM support and a Port 80 connection. Use this header to enhance
system performance and data security. See the table on the right for pin
definitions.
Definition
Pin #
Definition
1
LCLK
2
GND
3
LFRAME#
4
<(KEY)>
5
LRESET#
6
+5V (X)
7
LAD 3
8
LAD 2
9
+3.3V
10
LAD1
11
LAD0
12
GND
13
SMB_CLK4
14
SMB_DAT4
15
+3V_DUAL
16
SERIRQ
17
GND
18
CLKRUN# (X)
19
LPCPD#
20
LDRQ# (X)
Serial Ports
Two serial ports are included on the serverboard. COM1 is a rear I/O port and
COM2 is a header located near PCI-E slot 1, which may be used front front access..
Ethernet Ports
Two 10Gb Ethernet (LAN) ports are located on the I/O backplane. A dedicated IPMI
LAN port is also included. These ports accept RJ45 type cables.
Explanation of Jumpers
To modify the operation of the
serverboard, jumpers can be used
to choose between optional settings.
Jumpers create shorts between two
pins to change the function of the connector. Pin 1 is identified with a square
solder pad on the printed circuit board.
See the serverboard layout pages for
jumper locations.
Note: On a two-pin jumper, "Closed"
means the jumper is on both pins and
"Open" means the jumper is either on
only one pin or completely removed.
Connector
Pins
3
2
1
3
2
1
Jumper
Setting
CMOS Clear
JBT1 is used to clear CMOS (which will also clear any passwords). Instead of pins,
this jumper consists of contact pads to prevent accidentally clearing the contents
of CMOS.
To clear CMOS,
1. First power down the system and unplug the power cord(s).
2. With the power disconnected, short the CMOS pads with a metal object such
as a small screwdriver.
3. Remove the screwdriver (or shorting device).
4. Reconnect the power cord(s) and power on the system.
Note: Do not use the PW_ON connector to clear CMOS.
VGA Enable/Disable
JPG1 allows you to enable or disable
the VGA port. The default position is on
pins 1 and 2 to enable VGA. See the
table on the right for jumper settings.
5-20
5-21
VGA Enable/Disable
Jumper Settings
Jumper Setting
Definition
Pins 1-2
Enabled
Pins 2-3
Disabled
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Chapter 5: Advanced Serverboard Setup
Watch Dog Enable/Disable
LAN Enable/Disable
JPL1 enables or disables the Gb LAN
ports on the serverboard. See the
table on the right for jumper settings.
The default setting is Enabled.
GLAN Enable
Jumper Settings
Jumper Setting Definition
Pins 1-2
Enabled
Pins 2-3
Disabled
I2C Bus to PCI-Exp. Slots
Jumpers JI2C1 and JI2C2 allow you
to connect the System Management
Bus (I2C) to the PCI-Express slots to
improve PCI performance. The default
setting is Enabled. Both jumpers must
be set to the same setting See the
table on the right for jumper settings.
I2C to PCI-E Slots
Jumper Settings
Jumper Setting
Definition
Pins 1-2
Enabled
Pins 2-3
Disabled
Jumper JWD1 controls the Watch
Dog function. Watch Dog is a system monitor that can reboot the
system when a software application
hangs. Jumping pins 1-2 will cause
WD to reset the system if an application hangs. Jumping pins 2-3 will
generate a non-maskable interrupt
signal for the application that hangs.
See the table on the right for jumper
settings. Watch Dog must also be
enabled in BIOS.
Watch Dog
Jumper Settings
Jumper Setting
Note: When enabled, the user
needs to write their own application software in order to disable the
Watch Dog Timer.
Manufacturer's Mode
Jumper JPME2 allows the user to
flash the system firmware from a
host server in order to modify system
settings. Close this jumper to bypass
SPI flash security, and force ME into
recovery mode in order to use recovery jumpers. See the table on the right
for jumper settings.
ME Mode Select
Jumper Settings
Jumper Setting
Definition
Pins 1-2
Normal
Pins 2-3
Manufacture's Mode
BMC Enable
Jumper JPB1 allows you to enable
the embedded the ASpeed AST 2400
BMC (Baseboard Management) Controller to provide IPMI 2.0/KVM support on the serverboard. The default
setting is Enabled. See the table on
the right for jumper settings.
5-22
BMC Enable
Jumper Settings
Jumper Setting
Definition
Pins 1-2
Enabled
Pins 2-3
Disabled
5-23
Definition
Pins 1-2
Reset
Pins 2-3
NMI
Open
Disabled
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Chapter 5: Advanced Serverboard Setup
5-10 Onboard Indicators
5-11 SATA Ports
LAN LEDs
The Ethernet ports (located beside the
VGA port) have two LEDs. On each
port, the green LED flashes to indicate
activity while the other LED may be
green, amber or off to indicate the
speed of the connection. See the table
on the right for the functions associated with the connection speed LED.
LAN1/2 LED
(Connection Speed Indicator)
LED Color
No connection, 10 or 100 Mbps
Green
10 Gbps
Amber
1 Gbps
Dedicated IPMI LAN LEDs
A dedicated IPMI LAN is also located
on the I/O backplane. The amber LED
on the right indicates activity, while
the green LED on the left indicates
the speed of the connection. See the
table at right for more information.
Definition
Off
SATA Ports
There are ten SATA 3.0 ports included on the serverboard. Six ports (I-SATA 0-5)
are supported by the Intel PCH C612 while the other four are supported by the
Intel SCU and are located on a vertical S-SATA connector.
Note: For more information on SATA HostRAID configuration, please refer to the
Intel SATA HostRAID User's Guide posted on our website at http://www.supermicro.
com..
IPMI LAN Link LED (Left) &
Activity LED (Right)
Link (Left)
Activity (Right)
Color/State
Definition
Green: Solid
100 Mbps
Amber: Solid
1 Gbps
Amber: Blinking
Active
Onboard Power LED
An Onboard Power LED is located at
LE2. This LED indicator is lit when the
system is on. Be sure to unplug the
power cable before removing or adding any components. See the table on
the right for more details.
BMC Heartbeat LED
A BMC Heartbeat LED is located at
LEDM1 on the serverboard. When
blinking, the BMC is functioning normally.
5-24
Onboard PWR LED Indicator
LED States
Color/State
Definition
Off
System Power Off
Green: On
System Power On
BMC Heartbeat LED
States
Color/State
Definition
Green: Blinking
BMC Normal
5-25
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
5-12 Installing Software
Chapter 5: Advanced Serverboard Setup
SuperDoctor® 5
The Supermicro FTP site contains drivers and utilities for your system at ftp://ftp.
supermicro.com. Some of these must be installed, such as the chipset driver.
After accessing the FTP site, go into the CDR_Images directory and locate the ISO
file for your serverboard. Download this file to create a CD/DVD of the drivers and
utilities it contains. (You may also use a utility to extract the ISO file if preferred.)
Another option is to go to the Supermicro website at http://www.supermicro.com/
products/. Find the product page for your serverboard here, where you may download individual drivers and utilities.
After creating a CD/DVD with the ISO files, insert the disk into the CD/DVD drive
on your system and the display shown in Figure 5-6 should appear.
The Supermicro SuperDoctor 5 is a program that functions in a command-line or
web-based interface in Windows and Linux operating systems. The program monitors system health information such as CPU temperature, system voltages, system
power consumption, fan speed, and provides alerts via email or Simple Network
Management Protocol (SNMP).
SuperDoctor 5 comes in local and remote management versions and can be used
with Nagios to maximize your system monitoring needs. With SuperDoctor 5 Management Server (SSM Server), you can remotely control power on/off and reset
chassis intrusion for multiple systems with SuperDoctor 5 or IPMI. SD5 Management Server monitors HTTP, FTP, and SMTP services to optimize the efficiency of
your operation.
Note: The default User Name and Password for SuperDoctor 5 is admin / admin.
Figure 5-7. SuperDoctor 5 Interface Display Screen (Health Information)
Figure 5-6. Driver/Tool Installation Display Screen
Note: Click the icons showing a hand writing on paper to view the readme files
for each item. Click the computer icons to the right of these items to install each
item (from top to the bottom) one at a time. After installing each item, you must
re-boot the system before moving on to the next item on the list. The bottom
icon with a CD on it allows you to view the entire contents.
5-26
Note: The SuperDoctor 5 program and User’s Manual can be downloaded from
the Supermicro website at http://www.supermicro.com/products/nfo/sms_sd5.cfm.
5-27
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
5-13 Onboard Battery
Care must be taken to assure that the chassis cover is in place when the system
is operating to assure proper cooling. Out of warranty damage to the system can
occur if this practice is not strictly followed.
Figure 5-8. Installing the Onboard Battery
OR
Please handle used batteries carefully. Do not damage the battery in any way; a
damaged battery may release hazardous materials into the environment. Do not
discard a used battery in the garbage or a public landfill. Please comply with the
regulations set up by your local hazardous waste management agency to dispose
of your used battery properly.
5-28
Chapter 6: Advanced Chassis Setup
Chapter 6
Advanced Chassis Setup
This chapter covers the steps required to install components and perform maintenance on the SC846BE1C-R920B chassis. For component installation, follow the
steps in the order given to eliminate the most common problems encountered. If
some steps are unnecessary, skip ahead to the step that follows.
Tools Required: The only tool you will need to install components and perform
maintenance is a Philips screwdriver.
6-1 Static-Sensitive Devices
Electrostatic discharge (ESD) can damage electronic com­
ponents. To prevent
damage to any printed circuit boards (PCBs), it is important to handle them very
carefully. The following measures are generally sufficient to protect your equipment
from ESD damage.
Precautions
•Use a grounded wrist strap designed to prevent static discharge.
•Touch a grounded metal object before removing any board from its antistatic bag.
•Handle a board by its edges only; do not touch its components, peripheral chips,
memory modules or gold contacts.
•When handling chips or modules, avoid touching their pins.
•Put the serverboard, add-on cards and peripherals back into their antistatic
bags when not in use.
•For grounding purposes, make sure your computer chassis provides excellent
conductivity between the power supply, the case, the mounting fasteners and
the serverboard.
6-1
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Chapter 6: Advanced Chassis Setup
Figure 6-1. Front and Rear Chassis Views
5
11
17
23
4
10
16
22
3
9
15
21
2
8
14
20
1
7
13
19
0
6
12
18
Control Panel
6-3 Removing the Chassis Cover
13
1
1
12
Hard Drives (24)
Note: numbers indicate the logical drive bay locations.
Remove this screw
(if necessary)
Power Supplies (2)
Hardware RAID Add-on Card
JBOD Expansion Ports
Release Tab
Figure 6-2. Removing the Chassis Cover
Removing the Chassis Cover
Optional Rear Hot-Swap Drive Bays
I/O Ports
PCI Expansion Slots
You may need to gain access to the inside of the server to perform various maintenance tasks.
1. Press the release tabs to remove the cover from the locked position. Press
both tabs at the same time.
6-2 Control Panel
The control panel (located on the front of the chassis) must be connected to the
JF1 connector on the serverboard to provide you with system status indications. A
ribbon cable has bundled these wires together to simplify the connection.
Connect the cable from JF1 on the serverboard to the Control Panel PCB (printed
circuit board). Make sure the red wire plugs into pin 1 on both connectors. Pull all
excess cabling out of the airflow path. The LEDs inform you of system status. See
Chapter 3 for details on the LEDs and the control panel buttons. Details on JF1
can be found in Chapter 5.
6-2
2. Once the top cover is released from the locked position, slide the cover
toward the rear of the chassis.
3. Lift the cover off the chassis.
Warning: Except for short periods of time, do NOT operate the server without the
cover in place. The chassis cover must be in place to allow proper airflow and prevent
overheating.
6-3
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
6-4 System Fans
Chapter 6: Advanced Chassis Setup
Figure 6-3. Replacing System Cooling Fans
Three 8-cm hot-swap chassis fans and two 8-cm exhaust fans provide the cooling
for the SuperServer 6048R-E1CR24H. It is very important that the chassis top cover
is properly installed and making a good seal in order for the cooling air to circulate
properly through the chassis and cool the components. See Figure 6-3.
System Fan Failure
Fan speed is controlled by system temperature via IPMI. If a fan fails, the remaining
fans will ramp up to full speed and the overheat/fan fail LED on the control panel will
turn on. Replace any failed fan at your earliest convenience with the same type and
model (the system can continue to run with a failed fan). Remove the top chassis
cover while the system is still running to determine which of the fans has failed.
Replacing System Fans
Removing a Fan
1. Remove the top chassis cover while the system is still running to determine
which of the fans has failed.
2. Depress the tab on the side of the fan to unlock and remove the fan along
with its housing. The fan's power connections will automatically detach.
3. System power does not need to be shut down since the fans are hot-pluggable.
4. Replace the failed fan with an identical 8-cm, 12 volt fan (available from
Supermicro).
5. Position the new fan into the space vacated by the failed fan previously removed. A "click" can be heard when the fan is fully installed in place and the
power connections are made.
6. If the system power is on, the hot-plug feature will cause the fan to start immediately upon being connected to its header on the serverboard.
6-5 Drive Bay Installation/Removal
Accessing the Drive Bays
SATA Drives: You do not need to access the inside of the chassis or remove power
to replace or swap SATA drives. Proceed to the next step for instructions.
Note: You must use standard 1" high, drives in the SuperServer 6048R-E1CR24H.
Warning: Use caution when working around the backplane. Do not touch the backplane with any metal objects and make sure no ribbon cables touch the backplane or
obstruct the holes, which aid in proper airflow.
Rear Exhaust Fans
The two rear exhaust fans are also hot-swappable. To remove, depress the tab on
the side of the fan to unlock it, then pull it staight up and out of the chassis.
6-4
6-5
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Chapter 6: Advanced Chassis Setup
SATA Drive Installation
Figure 6-4. Mounting a SATA Drive in a Carrier
Mounting a SATA Drive in a Drive Carrier
The SATA drives are mounted in drive carriers to simplify their installation and
removal from the chassis. These carriers also help promote proper airflow for the
drives. For this reason, even empty carriers without SATA drives installed must remain in the chassis. To add a new SATA drive, install a drive into the carrier with the
printed circuit board side facing down so that the mounting holes align with those in
the carrier. Secure the drive to the carrier with four screws, as shown in Figure 6-3.
1
1
Installing/Removing SATA Drives
1. To remove a SATA drive carrier, first push the release button located beside
the drive's LEDs.
2. Swing the handle fully out and use it to pull the drive carrier straight out.
Warning: Regardless of how many hard drives are installed, all drive carriers must
remain in the drive bays to maintain proper airflow.
Installing a Hard Drive to the Hard Drive Tray
1. Remove the two screws securing the dummy drive to the drive tray and
remove the dummy drive.Place the hard drive tray on a flat surface such as a
desk, table or work bench (see Figure 6-4).
Figure 6-5. Installing a Drive Carrier
2. Slide the hard drive into the tray with the printed circuit board side facing
down.
3. Carefully align the mounting holes in both the drive tray and the hard drive.
4. Secure the hard drive to the tray using six screws.
5. Replace the drive tray into the chassis. Make sure to close the drive tray
handle to lock the drive tray into place (see Figure 6-5)..
15
Warning: Enterprise level hard disk drives are recommended for use in Supermicro
chassis and servers. For information on recommended HDDs, visit the Supermicro Web
site at http://www.supermicro.com/products/nfo/files/storage/SAS-1-CompList-110909.
Hard Drive Backplane
pdf
The hard drives plug into a backplane that provides power, drive ID and bus termination. A RAID controller can be used with the backplane to provide data security.
The operating system you use must have RAID support to enable the hot-swap
capability of the SATA drives. The backplane is already preconfigured, so there are
no jumpers or switches present on it.
6-6
6-7
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Removing the Air Shroud
Under most circumstances you will not need to remove the air shroud to perform
any service on the system. However, if you need to temporarily remove it (the air
shroud sould always be in place when the system is operating), please follow this
procedure.
Air shrouds concentrate airflow to maximize fan efficiency. The SC846 chassis air
shroud does not require screws to set up
Installing the Air Shroud
1. Confirm that your air shroud matches your chassis model. Each shroud is
labeled SC846LP, SC846RC, or SC846U.
2. Place the air shroud in the chassis. The air shroud fits behind the two fans
closest to the power supply.
Chapter 6: Advanced Chassis Setup
6-6 Power Supply
The SuperServer 6048R-E1CR24H has a 920 watt redundant, hot-plug power
supply consisting of two power modules. Each power supply module has an autoswitching capability, which enables it to automatically sense and operate at a 100V
- 240V input voltage.
Power Supply Failure
If either of the two power supply modules fail, the other will take the full load and
allow the system to continue operation without interruption. The Power Fail LED will
illuminate and remain on until the failed module has been replaced. Replacements
can be ordered directly from Supermicro (see contact information in the Preface).
The power supply modules have a hot-swap capability, meaning you can replace
the failed module without powering down the system.
Removing/Replacing the Power Supply
1. First unplug the power cord from the failed power supply module.
Figure 6-6. Removing the Air Shroud
2. Push the release tab on the back of the power supply as illustrated
3. Pull the power supply out using the handle provided.
4. Replace the failed power module with another of the same model.
5. Push the new power supply module into the power bay until it clicks into the
locked position.
6. Plug the AC power cord back into the module.
6-8
6-9
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Chapter 6: Advanced Chassis Setup
Figure 6-8. JBOD Expansion Port
JBOD OUT
(downstream port)
Figure 6-7. Replacing a Power Supply Module
Release
Tab
6-7 Attaching a JBOD Expansion Chassis
The SSG-6048R-E1CR24H features dual JBOD expansion ports. Figure 6-8 illustrates the recommended expansion strategy. JBOD attachment will vary depending
on the specific JBOD chassis that is being connected. Please follow the instructions
provided with the JBOD.
Note: the use of two cables (8x SAS lanes) is recommended.
6-10
6-11
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Notes
6-12
Chapter 7: BIOS
Chapter 7
BIOS
7-1 Introduction
This chapter describes the AMI BIOS setup utility for the X10DRH-C/CT/i/iT. The
ROM BIOS is stored in a Flash EEPROM and can be easily updated. This chapter
describes the basic navigation of the AMI BIOS setup utility screens.
Starting BIOS Setup Utility
To enter the AMI BIOS setup utility screens, press the <Delete> key while the
system is booting up.
Note: In most cases, the <Delete> key is used to invoke the AMI BIOS
setup screen.
Each main BIOS menu option is described in this manual. The AMI BIOS setup
menu screen has two main frames. The left frame displays all the options that can
be configured. Grayed-out options cannot be configured. Options in blue can be
configured by the user. The right frame displays the key legend. Above the key
legend is an area reserved for a text message. When an option is selected in the
left frame, it is highlighted in white. Often a text message will accompany it.
Note: the AMI BIOS has default text messages built in. Supermicro retains
the option to include, omit, or change any of these text messages.
The AMI BIOS setup utility uses a key-based navigation system called "hot keys."
Most of the AMI BIOS setup utility "hot keys" can be used at any time during the
setup navigation process. These keys include <F1>, <F4>, <Enter>, <Esc>, arrow
keys, etc.
Note: Options printed in Bold are default settings.
How To Change the Configuration Data
The configuration data that determines the system parameters may be changed by
entering the AMI BIOS setup utility. This setup utility can be accessed by pressing
<Del> at the appropriate time during system boot.
7-1
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
How to Start the Setup Utility
Normally, the only visible Power-On Self-Test (POST) routine is the memory test.
As the memory is being tested, press the <Delete> key to enter the main menu of
the AMI BIOS setup utility. From the main menu, you can access the other setup
screens. An AMI BIOS identification string is displayed at the left bottom corner of
the screen, below the copyright message.
Warning: Do not upgrade the BIOS unless your system has a BIOS-related issue.
Flashing the wrong BIOS can cause irreparable damage to the system. In no event shall
Supermicro be liable for direct, indirect, special, incidental, or consequential damages
arising from a BIOS update. If you have to update the BIOS, do not shut down or reset
the system while the BIOS is updating to avoid possible boot failure.
Chapter 7: BIOS
The following Main menu items will be displayed:
System Date/System Time
Use this option to change the system date and time. Highlight System Date or
System Time using the arrow keys. Enter new values using the keyboard. Press the
<Tab> key or the arrow keys to move between fields. The date must be entered in
Day MM/DD/YYYY format. The time is entered in HH:MM:SS format.
Note: The time is in the 24-hour format. For example, 5:30 P.M. appears
as 17:30:00.
Supermicro X10DRH-C/i
Version: This item displays the version of the BIOS ROM used in the system.
7-2 Main Setup
When you first enter the AMI BIOS setup utility, you will enter the Main setup screen.
You can always return to the Main setup screen by selecting the Main tab on the
top of the screen. The Main BIOS setup screen is shown below.
Build Date: This item displays the date when the version of the BIOS ROM used
in the system was built.
Memory Information
Total Memory: This item displays the total size of memory available in the system.
Memory Speed: This item displays the default speed of the memory modules
installed in the system.
7-2
7-3
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
7-3 Advanced Setup Configurations
Use the arrow keys to select Advanced setup and press <Enter> to access the
submenu items:
Chapter 7: BIOS
Wait For 'F1' If Error
Select Enabled to force the system to wait until the <F1> key is pressed if an error
occurs. The options are Disabled and Enabled.
Interrupt 19 Capture
Interrupt 19 is the software interrupt that handles the boot disk function. When this
item is set to Immediate, the ROM BIOS of the host adaptors will "capture" Interrupt
19 at bootup immediately and allow the drives that are attached to the host adaptors to function as bootable disks. If this item is set to Postponed, the ROM BIOS
of the host adaptors will not capture Interrupt 19 immediately to allow the drives
attached to the adaptors to function as bootable devices at bootup. The options
are Immediate and Postponed.
Re-try Boot
Select EFI Boot to allow the BIOS to automatically reboot the system from an EFI
boot device after its initial boot failure. Select Legacy Boot to allow the BIOS to
automatically reboot the system from a Legacy boot device after its initial boot
failure. The options are Disabled, Legacy Boot, and EFI Boot.
Warning: Use caution when changing the Advanced settings. An incorrect value, a
very high DRAM frequency or an incorrect BIOS timing setting may cause the system
to malfunction. If this occurs, restore the setting to the manufacture default setting.
Boot
Power Configuration
Watch Dog Function
Select Enabled to allow the Watch Dog timer to reboot the system when it is inactive for more than 5 minutes. The options are Enabled and Disabled.
Feature
Quiet Boot
Power Button Function
Use this feature to select the screen display between POST messages or the OEM
logo at bootup. Select Disabled to display the POST messages. Select Enabled
to display the OEM logo instead of the normal POST messages. The options are
Enabled and Disabled.
This feature controls how the system shuts down when the power button is pressed.
Select 4 Seconds Override for the user to power off the system after pressing and
holding the power button for 4 seconds or longer. Select Instant Off to instantly
power off the system as soon as the user presses the power button. The options
are 4 Seconds Override and Instant Off.
AddOn ROM Display Mode
Use this item to set the display mode for the Option ROM. Select Keep Current to
use the current AddOn ROM display setting. Select Force BIOS to use the Option
ROM display mode set by the system BIOS. The options are Force BIOS and
Keep Current.
Bootup Num-Lock State
Restore on AC Power Loss
Use this feature to set the power state after a power outage. Select Power Off for
the system power to remain off after a power loss. Select Power On for the system
power to be turned on after a power loss. Select Last State to allow the system
to resume its last power state before a power loss. The options are Power On,
Stay Off, and Last State.
Use this item to set the Power-on state for the Numlock key. The options are Off
and On.
7-4
7-5
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
CPU Configuration
This submenu displays the following CPU information as detected by the BIOS. It
also allows the user to configure CPU settings.
Chapter 7: BIOS
illegal codes to overwhelm the processor to damage the system during an attack.
The options are Enable and Disable. (Refer to Intel's and Microsoft's websites for
more information.)
•Processor Socket
PPIN Control
•Processor ID
Select Unlock/Enable to use the Protected-Processor Inventory Number (PPIN)
control in the system. The options are Unlock/Enable and Unlock/Disable.
•Processor Frequency
Hardware Prefetcher (Available when supported by the CPU)
•Processor Max Ratio
If set to Enable, the hardware prefetcher will prefetch streams of data and instructions from the main memory to the L2 cache to improve CPU performance. The
options are Disable and Enable.
•Processor Min Ratio
Adjacent Cache Prefetch (Available when supported by the CPU)
•Microcode Revision
Select Enable for the CPU to prefetch both cache lines for 128 bytes as comprised.
Select Disable for the CPU to prefetch both cache lines for 64 bytes. The options
are Disable and Enable.
•L1 Cache RAM
•L2 Cache RAM
Note: Please reboot the system for changes on this setting to take effect.
Please refer to Intel’s website for detailed information.
•L3 Cache RAM
•CPU 1 Version
DCU (Data Cache Unit) Streamer Prefetcher (Available when supported by
the CPU)
•CPU 2 Version
If set to Enable, the DCU Streamer prefetcher will prefetch data streams from the
cache memory to the DCU (Data Cache Unit) to speed up data accessing and
processing to enhance CPU performance. The options are Disable and Enable.
Clock Spread Spectrum
Select Enabled to allow the BIOS to monitor and attempt to reduce the level of
Electromagnetic Interference caused by the components whenever needed. The
options are Disabled and Enabled.
Hyper-Threading (All)
Select Enable to support Intel's Hyper-threading Technology to enhance CPU performance. The options are Enable and Disable.
Cores Enabled
This feature allows the user to determine the number of CPU cores to enable.
Enter "0" to enable all cores. The default setting is 0, which enables all CPU cores
in the system.
Execute Disable Bit (Available if supported by the OS & the CPU)
Select Enable for Execute Disable Bit Technology support, which will allow the
processor to designate areas in the system memory where an application code
can execute and where it cannot, thus preventing a worm or a virus from flooding
7-6
DCU IP Prefetcher
If set to Enable, the IP prefetcher in the DCU (Data Cache Unit) will prefetch IP
addresses to improve network connectivity and system performance. The options
are Enable and Disable.
Direct Cache Access (DCA)
Select Enable to use Intel DCA (Direct Cache Access) Technology to improve the
efficiency of data transferring and accessing. The options are Auto, Enable, and
Disable.
X2 APIC (Advanced Programmable Interrupt Controller)
Based on Intel's Hyper-Threading architecture, each logical processor (thread) is
assigned 256 APIC IDs (APIDs) in 8-bit bandwidth. When this feature is set to Enable, the APIC ID will expand(X2) from 8 bits to 16 bits to provide 512 APIDs to each
thread for CPU performance enhancement. The options are Disable and Enable.
7-7
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
AES-NI
Select Enable to use the Intel Advanced Encryption Standard (AES) New Instructions (NI) to ensure data security. The options are Enable and Disable.
Intel Virtualization Technology
Select Enable to use Intel Virtualization Technology support for Direct I/O VT-d support by reporting the I/O device assignments to the VMM (Virtual Machine Monitor)
through the DMAR ACPI tables. This feature offers fully-protected I/O resource
sharing across Intel platforms, providing greater reliability, security and availability
in networking and data-sharing. The options are Enable and Disable.
 Advanced Power Management Configuration
Advanced Power Management Configuration
Power Technology
Select Energy Efficient to support power-saving mode. Select Custom to customize system power settings. Select Disabled to disable power-saving settings. The
options are Disable, Energy Efficient, and Custom.
CPU P State Control (Available when Power Technology
is set to Custom)
EIST (P-States)
EIST (Enhanced Intel SpeedStep Technology) allows the system to automatically
adjust the processor voltage and core frequency to reduce power consumption
and heat dissipation. The options are Disable and Enable.
Turbo Mode
Select Enabled to use the Turbo Mode to boost system performance. The options
are Enable and Disable.
Chapter 7: BIOS
CPU C State Control (Available when Power Technology
is set to Custom)
Package C State limit
Use this item to set the limit on the C-State package register. The options are
C0/1 state, C2 state, C6 (non-Retention) state, C6 (Retention) state, and No
Limit.
CPU C3 Report
Select Enable to allow the BIOS to report the CPU C3 State (ACPI C2) to the
operating system. During the CPU C3 State, the CPU clock generator is turned
off. The options are Enable and Disable.
CPU C6 Report (Available when Power Technology is set to Custom)
Select Enable to allow the BIOS to report the CPU C6 state (ACPI C3) to the
operating system. During the CPU C6 state, power to all cache is turned off.
The options are Enable and Disable.
Enhanced Halt State (C1E)
Select Enabled to use Enhanced Halt-State technology, which will significantly
reduce CPU power consumption by reducing CPU clock cycles and voltages
during a Halt-state. The options are Disable and Enable.
CPU T State Control (Available when Power Technology
is set to Custom)
ACPI (Advanced Configuration Power Interface) T-States
Select Enable to support CPU throttling by the operating system to reduce power
consumption. The options are Enable and Disable.
Socket RAPL (Running Average Power Limit) Config.
P-State Coordination
(Configuration)
This feature is used to change the P-state (Power-Performance State) coordination type. P-state is also known as "SpeedStep" for Intel processors. Select
HW_ALL to change the P-state coordination type for hardware components only.
Select SW_ALL to change the P-state coordination type for all software installed
in the system. Select SW_ANY to change the P-state coordination type for a software program in the system. The options are HW_All, SW_ALL, and SW_ANY.
FAST_RAPL_NSTRIKE_PL2_DUTY_CYCLE
7-8
This feature displays the value of the item above within the range between 25
(10%) and 64 (25%). The default setting is 64.
Turbo Power Limit Lock
Select Enable to set the power use limit for the machine when it is running in
the turbo mode. The options are Enable and Disable.
7-9
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Chapter 7: BIOS
Long Pwr (Power) Limit Ovrd (Override)
Override BW_LIMIT_TF (BW_limit_tf )
Select Enable to support long-term power limit override. If this feature is disabled,
BIOS will set the default value. The options are Enable and Disable.
This feature allows the user to turn off the "Override BW_Limit_TF (Time Frame)"
setting when the item--the "Running Average Power Limit for DRAM modules"
(DRAM RAPL) is set to Enabled so that the DRAM RAPL setting can work
properly. The default setting is 1.
Long Dur (Duration) Power Limit
This item displays the power limit set by the user during which long duration
power is maintained. The default setting is 0.
DRAM RAPL (Running Average Power Limit) Extended Range
Long Dur (Duration) Time Window
Select Enable to extend the RAPL range for the DRAM modules. The options
are Disable and Enable.
Use this item to set the time window value (in seconds) over which the TDP
(Thermal Design Point) should be maintained. The default setting is 1, which will
allow the value to be automatically programed by the system.
Pkg (Package) Clmp (Clamping) Limit1
Use this item to set the limit on power performance states for the runtime processor, with P0 being the state with the highest frequency (clock speed) and power
(consumption), and P1, a step lower in performance than P0, with its frequency
and voltage scaled back a notch. The options are Between P1/P0 and Below P1.
Short Dur (Duration) Pwr (Power) Limit En (Enable)
Select Enable to support Short Duration Power Limit (Power Limit 2). The options
are Enable and Disable.
Short Dur (Duration) Pwr (Power) Limit
This item displays the time period during which short duration power is maintained. The default setting is 0.
Pkg (Package) Clmp (Clamping) Lim2
Use this item to set the limit on power performance states for the processor
operating in turbo mode, with P0 being the state with the highest frequency
(clock speed) and power (consumption), and P1, a step lower in performance
than P0, with its frequency and voltage scaled back a notch. The options are
Between P1/P0 and Below P1.
DRAM RAPL (Running Average Power Limit) Configuration
DRAM RAPL (Running Average Power Limit) Baseline
Use this item to set the run-time power-limit baseline for DRAM modules. The
options are Disable, DRAM RAPL Mode 0, and DRAM RAPL Mode 1.
7-10
Chipset Configuration
Warning! Please set the correct settings for the items below. A wrong configuration
setting may cause the system to become malfunction.
North Bridge
This feature allows the user to configure the settings for the Intel North Bridge.
IIO Configuration
EV DFX (Device Function On-Hide) Features
When this feature is set to Enable, the EV_DFX Lock Bits that are located on a
processor will always remain clear during electric tuning. The options are Disable and Enable.
IIO0 Configuration
IOU2 (II0 PCIe Port 1)
This item configures the PCI-E port Bifuraction setting for a PCI-E port specified
by the user. The options are x4x4, x8, and Auto.
IOU0 (II0 PCIe Port 2)
This item configures the PCI-E port Bifuraction setting for a PCI-E port specified
by the user. The options are x4x4x4x4, x4x4x8, x8x4x4, x8x8, x16, and Auto.
IOU1 (II01 PCIe Port 3)
This item configures the PCI-E port Bifuraction setting for a PCI-E port specified
by the user. The options are x4x4x4x4, x4x4x8, x8x4x4, x8x8, x16, and Auto..
7-11
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Chapter 7: BIOS
No PCIe Port Active ECO (Engineer Change Order)
L0s Support
This feature provides a work-around solution when there is no active PCI device
detected by the BIOS. The options are PCU Squelch Exit Ignore Option and
Reset the SQ FLOP by CSR Option.
When this item is set to Disable, IIO will not put its transmitter in the L0s state.
The default setting is Disable.
Socket 0 PCIeD00F0 - Port 0/DMI
Socket 0 PCIeD01F0 - Port 1A/Socket 0 PCIeD02F0
- Port 2A/Socket 0 PCIeD20F2 - Port 2C/Socket 0
PCIeD03F0 - Port 3A/Socket 0 PCIeD03F2 - Port 3C
Link Speed
This item configures the link speed of a PCI-E port specified by the user. The
options are Gen 1 (Generation 1) (2.5 GT/s), Gen 2 (Generation 2) (5 GT/s),
and Auto.
PCI-E Port
PCI-E Port DeEmphasis
Hot Plug Capable
This item configures the De-Emphasis Control (LANKCON2 [6]) setting for this
computer. The options are -6.0 dB and -3.5 dB.
Select Enable to enable hot-plugging support for the PCI-E port specified by the
user to allow the user to replace the device installed on the port without shutting
down the system. The options are Disable and Enable.
The following items will be display:
•PCI-E Port Link Status
Select Enable to enable the PCI-E port specified by the user. The options are
Auto, Enable, and Disable.
PCI-E Port Link
•PCI-E Port Link Max
Select Disable to disable the link that is not involved in training activities, but its
CFG is still active. The options are Enable and Disable.
•PCI-E Port Link Speed
Link Speed
PCI-E Port L0s Exit Latency
Use this item to set the length of time required for the port specified by the user
to complete the transition from L0s to L0. The default setting is 4uS - 8uS.
PCI-E Port L1 Exit Latency
Use this item to set the length of time required for the port specified by the user
to complete the transition from L1 to L0. The default setting is <1uS, 1uS - 2uS,
2uS - 4uS, 4uS - 8uS, 8uS - 16uS, 16uS - 32uS, 32uS - 64uS, and >64uS.
Use this item to select the link speed for the PCI-E port specified by the user.
The options are GEN1 (2.5 GT/s), GEN2 (5 GT/s), GEN3 (8 GT/s), and Auto.
PCI-E Port DeEmphasis
Use this item to select the De-Emphasis control setting for a PCI-E port specified
by the user. The options are -6.0 dB and -3.5 dB.
The following items will be display:
•PCI-E Port Link Status
Fatal Err (Error) Over
•PCI-E Port Link Max
Select Enable to force fatal error prorogation to the IIO core error logic for the
port specified by the user. The options are Disable and Enable.
•PCI-E Port Link Speed
Non-Fatal Err (Error) Over
PCI-E Port L0s Exit Latency
Select Enable to force non-fatal error prorogation to the IIO core error logic for
the port specified by the user. The options are Disable and Enable.
Use this item to set the length of time required for the port specified by the user
to complete the transition from L0s to L0. The default setting is 4uS - 8uS.
Corr Err (Correctable Error) Over
Select Enable to force correctable error prorogation to the IIIO core error logic
for the port specified by the user. The options are Disable and Enable.
7-12
7-13
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
PCI-E Port L1 Exit Latency
Use this item to set the length of time required for the port specified by the user
to complete the transition from L1 to L0. The default setting is <1uS, 1uS - 2uS,
2uS - 4uS, 4uS - 8uS, 8uS - 16uS, 16uS - 32uS, 32uS - 64uS, and >64uS.
Chapter 7: BIOS
dB), P5 (0.0/2.0 dB), P6 (0.0/2.5 dB), P7 (-6.0 /3.5 dB), P8 (-3.5/3.5 dB), and
P9 (0.0/3.5 dB).
Gen3 (Generation 3) DN RX Preset Hint
Select Enable to force fatal error prorogation to the IIO core error logic for the
port specified by the user. The options are Disable and Enable.
Use this item to set the Preset Hint mode for PCI-E Gen3 downstream receiving
(RX) from the master device to a slave device. The options are Auto, P0 (-6.0
dB), P1 (-7.0 dB), P2 (-8.0 dB), P3 (-9.0 dB), P4 (-10.0 dB) P5 (-11.0 dB), and
P6 (-12.0 dB).
Non-Fatal Err (Error) Over
Gen3 (Generation 3) Up TX Preset
Select Enable to force non-fatal error prorogation to the IIO core error logic for
the port specified by the user. The options are Disable and Enable.
Corr Err (Correctable Error) Over
Use this item to set the Preset mode for PCI-E Gen3 upstream transmitting (TX)
from a slave device to the master device.The options are Auto, P0 (-6.0/0.0 dB),
P1 (-3.5/0.0 dB), P2 (-4.5/0.0 dB), P3 (-2.5/0.0 dB), P4 (0.0/0.0 dB), P5 (0.0/2.0
dB), P6 (0.0/2.5 dB), P7 (-6.0/3.5 dB), P8 (-3.5/3.5 dB), and P9 (0.0/3.5 dB).
Select Enable to force correctable error prorogation to the IIIO core error logic
for the port specified by the user. The options are Disable and Enable.
Non-Transparent Bridge PCIe Port Definition (Available on the Socket 0
PCIeD03F0 - Port 3A only)
Fatal Err (Error) Over
L0s Support
When this item is set to Disable, IIO will not put its transmitter in the L0s state.
The default setting is Disable.
Select Transparent Bridge to enable Transparent Bridge support for the PCI-E
port specified by the user. Please do not select NTB-RP for a legacy IIO device.
The options are Transparent Bridge, NTB to NTB, and NTB to RP.
Hide Port?
PM ACPI Support
Select Enable to generate an _HPGPE message on a PM ACPI event. Select
Disable to generate an MSI message. The options are Disable and Enable.
Select Yes to hide the PCI-E port specified from the OS. The options are No
and Yes.
This feature allows the user to configure the settings for the Intel North Bridge.
Gen3 (Generation 3) Eq (Equalization) Mode
Use this item to set the "Adaptive Equalization" mode for PCI-E Generation 3
devices. The options are Auto, Enable Phase 0, 1, 2, 3; Disable Phase 0, 1,
2, 3; Enable Phase 1 Only, Enable Phase 0, 1 Only, Enable MMM Offset West,
and Advanced.
Gen3 (Generation 3) Spec (Specifics) Mode
Use this item to set the Specifics mode for PCI-E Generation 3 devices. The
options are Auto, 0.70 July, 0.70 Sept and 071 Sept.
Gen3 (Generation 3) Phase2 Mode
Use this item to set the PCI-E Generation 3 Phase 2 mode. The options are
Hardware Adaptive and Manual.
Gen3 (Generation 3) DN TX Preset
IIO1 Configuration
IOU2 (II0 PCIe Port 1)
This item configures the PCI-E port Bifuraction setting for a PCI-E port specified
by the user. The options are x4x4, x8, and Auto.
IOU0 (II0 PCIe Port 2)
This item configures the PCI-E port Bifuraction setting for a PCI-E port specified
by the user. The options are x4x4x4x4, x4x4x8, x8x4x4, x8x8, x16, and Auto.
IOU1 (II01 PCIe Port 3)
This item configures the PCI-E port Bifuraction setting for a PCI-E port specified
by the user. The options are x4x4x4x4, x4x4x8, x8x4x4, x8x8, x16, and Auto..
Use this item to set the Preset mode for PCI-E Gen3 downstream transmitting (TX) from the master device to a slave device. The options are Auto, P0
(-6.0/0.0 dB), P1 (-3.5/0.0 dB), P2 (-4.5/0.0 dB), P3 (-2.5/0.0 dB), P4 (0.0/0.0
7-14
7-15
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Chapter 7: BIOS
No PCIe Port Active ECO (Engineer Change Order)
PCI-E Port L1 Exit Latency
This feature provides a work-around solution when there is no active PCI device
detected by the BIOS. The options are PCU Squelch Exit Ignore Option and
Use this item to set the length of time required for the port specified by the user
to complete the transition from L1 to L0. The default setting is <1uS, 1uS - 2uS,
Reset the SQ FLOP by CSR Option..
Socket 1 PCIeD00F0 - Port 0/DMI/Socket 1 PCIeD01F0
- Port 1A/Socket 1 PCIeD02F0 - Port 2A/Socket 1
PCIeD20F2 - Port 2C/Socket 1 PCIeD03F0 - Port 3A
PCI-E Port
Select Enable to enable the PCI-E port specified by the user. The options are
Auto, Enable, and Disable.
2uS - 4uS, 4uS - 8uS, 8uS - 16uS, 16uS - 32uS, 32uS - 64uS, and >64uS.
Fatal Err (Error) Over
Select Enable to force fatal error prorogation to the IIO core error logic for the
port specified by the user. The options are Disable and Enable.
Non-Fatal Err (Error) Over
Select Enable to force non-fatal error prorogation to the IIO core error logic for
the port specified by the user. The options are Disable and Enable.
Corr Err (Correctable Error) Over
Hot Plug Capable
Select Enable to enable hot-plugging support for the PCI-E port specified by the
user to allow the user to replace the device installed on the port without shutting
down the system. The options are Disable and Enable.
PCI-E Port Link
Select Disable to disable the link that is not involved in training activities, but its
CFG is still active. The options are Enable and Disable.
Link Speed
Use this item to select the link speed for the PCI-E port specified by the user.
The options are GEN1 (2.5 GT/s), GEN2 (5 GT/s), GEN3 (8 GT/s), and Auto.
PCI-E Port DeEmphasis
Use this item to select the De-Emphasis control setting for a PCI-E port specified
by the user. The options are -6.0 dB and -3.5 dB.
The following items will be display:
•PCI-E Port Link Status
Select Enable to force correctable error prorogation to the IIIO core error logic
for the port specified by the user. The options are Disable and Enable.
L0s Support
When this item is set to Disable, IIO will not put its transmitter in the L0s state.
The default setting is Disable.
PM ACPI Support
Select Enable to generate an _HPGPE message on a PM ACPI event. Select
Disable to generate an MSI message. The options are Disable and Enable.
Gen3 (Generation 3) Eq (Equalization) Mode
Use this item to set the "Adaptive Equalization" mode for PCI-E Generation 3
devices. The options are Auto, Enable Phase 0, 1, 2, 3; Disable Phase 0, 1,
2, 3; Enable Phase 1 Only, Enable Phase 0, 1 Only, Enable MMM Offset West,
and Advanced.
Gen3 (Generation 3) Spec (Specifics) Mode
Use this item to set the Specifics mode for PCI-E Generation 3 devices. The
options are Auto, 0.70 July, 0.70 Sept and 071 Sept.
•PCI-E Port Link Max
•PCI-E Port Link Speed
Gen3 (Generation 3) Phase2 Mode
Use this item to set the PCI-E Generation 3 Phase 2 mode. The options are
Hardware Adaptive and Manual.
PCI-E Port L0s Exit Latency
Use this item to set the length of time required for the port specified by the user
to complete the transition from L0s to L0. The default setting is 4uS - 8uS.
7-16
Gen3 (Generation 3) DN TX Preset
Use this item to set the Preset mode for PCI-E Gen3 downstream transmitting (TX) from the master device to a slave device. The options are Auto, P0
(-6.0/0.0 dB), P1 (-3.5/0.0 dB), P2 (-4.5/0.0 dB), P3 (-2.5/0.0 dB), P4 (0.0/0.0
7-17
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
dB), P5 (0.0/2.0 dB), P6 (0.0/2.5 dB), P7 (-6.0 /3.5 dB), P8 (-3.5/3.5 dB), and
P9 (0.0/3.5 dB).
Gen3 (Generation 3) DN RX Preset Hint
Chapter 7: BIOS
 Intel VT for Directed I/O (VT-d)
Intel® VT for Directed I/O (VT-d)
Use this item to set the Preset Hint mode for PCI-E Gen3 downstream receiving
(RX) from the master device to a slave device. The options are Auto, P0 (-6.0
dB), P1 (-7.0 dB), P2 (-8.0 dB), P3 (-9.0 dB), P4 (-10.0 dB) P5 (-11.0 dB), and
P6 (-12.0 dB).
Select Enable to use Intel Virtualization Technology for Direct I/O VT-d support
by reporting the I/O device assignments to the VMM (Virtual Machine Monitor)
through the DMAR ACPI tables. This feature offers fully-protected I/O resource
sharing across Intel platforms, providing greater reliability, security and availability in networking and data-sharing. The options are Enable and Disable.
Gen3 (Generation 3) Up TX Preset
Interrupt Remapping
Use this item to set the Preset mode for PCI-E Gen3 upstream transmitting (TX)
from a slave device to the master device.The options are Auto, P0 (-6.0/0.0 dB),
P1 (-3.5/0.0 dB), P2 (-4.5/0.0 dB), P3 (-2.5/0.0 dB), P4 (0.0/0.0 dB), P5 (0.0/2.0
dB), P6 (0.0/2.5 dB), P7 (-6.0/3.5 dB), P8 (-3.5/3.5 dB), and P9 (0.0/3.5 dB).
Select Enable for Interrupt Remapping support to enhance system performance.
The options are Enable and Disable.
Non-Transparent Bridge PCIe Port Definition (Available on the Socket 1
PCIeD03F0 - Port 3A only)
Select Transparent Bridge to enable Transparent Bridge support for the PCI-E
port specified by the user. Please do not select NTB-RP for a legacy IIO device.
The options are Transparent Bridge, NTB to NTB, and NTB to RP.
QPI (Quick Path Interconnect) Configuration
QPI General Configuration
QPI Status
The following information will display:
Hide Port?
•Number of CPU
Select Yes to hide the PCI-E port specified from the OS. The options are No
and Yes.
•Number of II0
IOAT (Intel® IO Acceleration) Configuration
•Current QPI Link Speed
•Current QPI Link Frequency
Enable IOAT
Select Enable to enable Intel I/OAT (I/O Acceleration Technology) support, which
significantly reduces CPU overhead by leveraging CPU architectural improvements and freeing the system resource for other tasks. The options are Enable
and Disable.
No Snoop
Select Enable to support no-snoop mode for each CB device. The options are
Disable and Enable.
Relaxed Ordering
Select Enable to enable Relaxed Ordering support which will allow certain
transactions to violate the strict-ordering rules of PCI bus for a transaction to
be completed prior to other transactions that have already been enqueued. The
options are Disable and Enable.
7-18
•QPI Global MMIO Low Base/Limit
•QPI Global MMIO High Base/Limit
•QPI PCIe Configuration Base/Size
Link Frequency Select
Use this item to select the desired frequency for QPI Link connections. The options are 6.4GB/s, 8.0GB/s, 9.6GB/s, Auto, and Auto Limited.
Link L0p Enable
Select Enable for Link L0p support to reduce power consumption. The options
are Enable and Disable.
7-19
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Chapter 7: BIOS
Link L1 Enable
Set Throttling Mode
Select Enable for Link L1 support to reduce power consumption. The options
are Enable and Disable.
Throttling improves CPU reliability and reduces power consumption via automatic-voltage control during CPU idle states. The options are Disabled and CLTT
(Closed Loop Thermal Throttling).
COD Enable (Available when the OS and the CPU support this feature)
Select Enable for Cluster-On-Die support to enhance system performance in
cloud computing. The options are Enable and Disable.
Early Snoop (Available when the OS and the CPU support this feature)
Select Enable for Early Snoop support to enhance system performance. The
options are Enable, Disable, and Auto.
Isoc Mode
Select Enable for Isochronous support to meet QoS (Quality of Service) requirements. This feature is especially important for Intel Virtualization Technology. The
options are Enable and Disable.
Socket Interleave Below 4GB
Select Enable for the memory above the 4G Address space to be split between
two sockets. The options are Enable and Disable.
A7 Mode
Select Enable to support the A7 (Addressing) mode to improve memory performance. The options are Enable and Disable.
DIMM Information
This item displays the status of a DIMM module as detected by the AMI
BIOS.
•P1 DIMMA1
Memory Configuration
This submenu allows the user to configure Integrated Memory Controller (IMC)
settings.
Enforce POR
Select Enabled to enforce POR restrictions on DDR4 frequency and voltage
programming. The options are Enabled and Disabled.
•P2 DIMME1
Memory RAS (Reliability_Availability_Serviceability) Configuration
Use this submenu to configure the following Memory RAS settings.
RAS Mode
Memory Frequency
Use this feature to set the maximum memory frequency for onboard memory
modules. The options are Auto, 1333, 1400, 1600, 1800, 1867, 2000, 2133,
2200, 2400, 2600, 2667, 2800, 2993, 3000, 3200, and Reserved (Do not select
Reserved).
Data Scrambling
Select Enabled to enable data scrambling to enhance system performance and
data integrity. The options are Auto, Disabled and Enabled.
DRAM RAPL (Running Average Power Limit) Baseline
Use this feature to set the run-time power-limit baseline for DRAM modules. The
options are Disable, DRAM RAPL Mode 0, and DRAM RAPL Mode 1.
7-20
When Disable is selected, RAS is not supported. When Mirror is selected, the
motherboard maintains two identical copies of all data in memory for data backup.
When Lockstep is selected, the motherboard uses two areas of memory to run
the same set of operations in parallel to boost performance. The options are
Disable, Mirror, and Lockstep Mode.
Memory Rank Sparing
Select Enable to enable memory-sparing support for memory ranks to improve
memory performance. The options are Disabled and Enabled.
Patrol Scrub
Patrol Scrubbing is a process that allows the CPU to correct correctable memory
errors detected on a memory module and send the correction to the requestor
(the original source). When this item is set to Enable, the IO hub will read and
write back one cache line every 16K cycles, if there is no delay caused by internal
processing. By using this method, roughly 64 GB of memory behind the IO hub
will be scrubbed every day. The options are Enable and Disable.
7-21
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Chapter 7: BIOS
Patrol Scrub Interval
Port 60/64 Emulation
This feature allows you to decide how many hours the system should wait before
the next complete patrol scrub is performed. Use the keyboard to enter a value
from 0-24. The Default setting is 24.
Select Enabled to support I/O port 60h/64h emulation, which will provide complete
legacy USB keyboard support for the operating systems that do not support legacy
USB devices. The options are Disabled and Enabled.
Demand Scrub
USB 3.0 Support
Demand Scrubbing is a process that allows the CPU to correct correctable
memory errors found on a memory module. When the CPU or I/O issues a
demand-read command, and the read data from memory turns out to be a
correctable error, the error is corrected and sent to the requestor (the original
source). Memory is updated as well. Select Enable to use Demand Scrubbing
for ECC memory correction. The options are Enable and Disable.
Select Enabled for USB 3.0 support. The options are Smart Auto, Auto, Enabled,
and Disabled.
Device Tagging
Select Enable to support device tagging. The options are Disable and Enable.
South
Bridge Configuration
The following South Bridge information will display:
USB
EHCI1
Select Enabled to enable EHCI (Enhanced Host Controller Interface) support on
USB 2.0 connector #1 (-at least one USB 2.0 connector should be enabled for EHCI
support.) The options are Disabled and Enabled.
EHCI2
Select Enabled to enable EHCI (Enhanced Host Controller Interface) support on
USB 2.0 connector #2 (-at least one USB 2.0 connector should be enabled for EHCI
support.) The options are Disabled and Enabled.
Configuration
•USB Module Version
•USB Devices
Legacy USB Support
Select Enabled to support onboard legacy USB devices. Select Auto to disable
legacy support if there are no legacy USB devices present. Select Disabled to
have all USB devices available for EFI applications only. The options are Enabled,
Disabled and Auto.
XHCI Hand-Off
This is a work-around solution for operating systems that do not support XHCI (Extensible Host Controller Interface) hand-off. The XHCI ownership change should be
claimed by the XHCI driver. The settings are Enabled and Disabled.
EHCI Hand-Off
This item is for operating systems that do not support Enhanced Host Controller
Interface (EHCI) hand-off. When this item is enabled, EHCI ownership change will
be claimed by the EHCI driver. The settings are Enabled and Disabled.
7-22
7-23
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
SATA
Configuration
When this submenu is selected, AMI BIOS automatically detects the presence of
the SATA devices that are supported by the Intel PCH chip and displays the following items:
Chapter 7: BIOS
*If the item above "Configure SATA as" is set to IDE, the following items will
display:
SATA Port 0~ Port 5
This item displays the information of a SATA device installed on the SATA port
specified by the user.
SATA Controller
Select Enabled to enable the onboard SATA controller supported by the Intel PCH
chip. The options are Enabled and Disabled.
•Software Preserve
SATA Device Type (Available when a SATA port is detected)
Configure SATA as
Select IDE to configure a SATA drive specified by the user as an IDE drive. Select
AHCI to configure a SATA drive specified by the user as an AHCI drive. Select
RAID to configure a SATA drive specified by the user as a RAID drive. The options
are IDE, AHCI, and RAID.
*If the item above "Configure SATA as" is set to AHCI, the following items will display:
Support Aggressive Link Power Management
When this item is set to Enabled, the SATA AHCI controller manages the power
usage of the SATA link. The controller will put the link to a low power state when
the I/O is inactive for an extended period of time, and the power state will return
to normal when the I/O becomes active. The options are Enabled and Disabled.
Use this item to specify if the SATA port specified by the user should be connected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk
Drive and Solid State Drive.
*If the item above "Configure SATA as" is set to RAID, the following items will
display:
Support Aggressive Link Power Management
When this item is set to Enabled, the SATA AHCI controller manages the power
usage of the SATA link. The controller will put the link to a low power state when
the I/O is inactive for an extended period of time, and the power state will return
to normal when the I/O becomes active. The options are Enabled and Disabled.
SATA RAID Option ROM/UEFI Driver
SATA Port 0~ Port 5
This item displays the information of a SATA device installed on the SATA port
specified by the user.
Select EFI to load the EFI driver for system boot. Select Legacy to load a legacy
OPROM for system boot. The options are Disabled, EFI, and Legacy.
•Model number of drive and capacity
SATA/sSATA RAID Boot Select
•Software Preserve
Select SATA Controller to boot the system from a SATA RAID device. Select sSATA
Controller to boot the system from a sSATA RAID device. Select Both to boot the
system either from a SATA RAID device or from an sSATA RAID device. Please
note that the option-Both is not supported by the Windows Server 2012/R2 OS. The
options are None, Both, SATA Controller, and sSATA Controller.
Port 0~ Port 5
Select Enabled to enable a SATA port specified by the user. The options are Disabled and Enabled.
Spin Up Device
On an edge detect from 0 to 1, set this item to allow the PCH to initialize the
device. The options are Enabled and Disabled.
Serial ATA Port 0~ Port 5
This item displays the information of a SATA device installed on the SATA port
specified by the user.
•Model number of drive and capacity
•Software Preserve
SATA Device Type
Use this item to specify if the SATA port specified by the user should be connected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk
Drive and Solid State Drive.
7-24
7-25
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Chapter 7: BIOS
Port 0~ Port 5
sSATA Port 0~ Port 3
Select Enabled to enable a SATA port specified by the user. The options are
Disabled and Enabled.
Select Enabled to enable an sSATA port specified by the user. The options are
Disabled and Enabled.
Spin Up Device
Spin Up Device
On an edge detect from 0 to 1, set this item to allow the PCH to start a COMRESET initialization to the device. The options are Enabled and Disabled.
On an edge detect from 0 to 1, set this item to allow the PCH to start a COMRESET initialization to the device. The options are Enabled and Disabled.
SATA Device Type
Device Type
Use this item to specify if the SATA port specified by the user should be connected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk
Drive and Solid State Drive.
Use this item to specify if the sSATA port specified by the user should be connected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk
Drive and Solid State Drive.
sSATA
*If the item above "Configure sSATA as" is set to IDE, the following items will
display:
Configuration
When this submenu is selected, AMI BIOS automatically detects the presence of
the SATA devices that are supported by the PCH-sSATA controller and displays
the following items:
sSATA Controller
This item enables or disables the onboard SATA controller supported by the Intel
PCH-sSATA controller. The options are Enabled and Disabled.
Configure sSATA as
Select IDE to configure an sSATA drive specified by the user as an IDE drive. Select
AHCI to configure an sSATA drive specified by the user as an AHCI drive. Select
RAID to configure an sSATA drive specified by the user as a RAID drive. The options are IDE, AHCI, and RAID.
*If the item above "Configure sSATA as" is set to AHCI, the following items will
display:
Support Aggressive Link Power Management
When this item is set to Enabled, the SATA AHCI controller manages the power
usage of the SATA link. The controller will put the link to a low power state when
the I/O is inactive for an extended period of time, and the power state will return
to normal when the I/O becomes active. The options are Enabled and Disabled.
sSATA Port 0~ Port 3
This item indicates that an sSATA port specified by the user is installed (present)
or not.
sSATA Device Type (Available when a sSATA port is detected)
Use this item to specify if the sSATA port specified by the user should be connected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk
Drive and Solid State Drive.
*If the item above "Configure sSATA as" is set to RAID, the following items will
display:
Support Aggressive Link Power Management
When this item is set to Enabled, the SATA AHCI controller manages the power
usage of the sSATA link. The controller will put the link to a low power state when
the I/O is inactive for an extended period of time, and the power state will return
to normal when the I/O becomes active. The options are Enabled and Disabled.
sSATA RAID Option ROM/UEFI Driver
Select EFI to load the EFI driver for system boot. Select Legacy to load a legacy
OPROM for system boot. The options are Disabled, EFI, and Legacy.
sSATA Port 0~ Port 3
SATA/sSATA RAID Boot Select
This item displays the information detected on the installed on the sSATA port.
specified by the user.
Select SATA Controller to boot the system from a SATA RAID device. Select sSATA
Controller to boot the system from a sSATA RAID device. Select Both to boot the
system either from a SATA RAID device or from an sSATA RAID device. Please
note that the option-Both is not supported by the Windows Server 2012/R2 OS. The
options are None, Both, SATA Controller, and sSATA Controller.
•Model number of drive and capacity
7-26
7-27
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Chapter 7: BIOS
sSATA Port 0~ Port 3
PCIe/PCI/PnP Configuration
Select Enabled to enable an sSATA port specified by the user. The options are
Disabled and Enabled.
PCI Latency Timer
Spin Up Device
On an edge detect from 0 to 1, set this item to allow the PCH to start a COMRESET initialization to the device. The options are Enabled and Disabled.
Device Type
Use this item to specify if the sSATA port specified by the user should be connected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk
Drive and Solid State Drive.
Server ME (Management Engine) Configuration
Use this item to configure the PCI latency timer for a device installed on a PCI bus.
Select 32 to set the PCI latency timer to 32 PCI clock cycles. The options are 32,
64, 96, 128, 160, 192, 224, and 248 (PCI Bus Clocks).
PERR# Generation
Select Enabled to allow a PCI device to generate a PERR (PCI/PCI-E Parity Error)
number for a PCI bus error event. The options are Enabled and Disabled.
SERR# Generation
Select Enabled to allow a PCI device to generate an SERR (System Error) number
for a PCI bus error event. The options are Enabled and Disabled.
This feature displays the following system ME configuration settings.
PCI PERR/SERR Support
•General ME Configuration
Select Enabled to support PERR (PCI/PCI-E Parity Error)/SERR (System Error)
runtime error reporting for a PCI/PCI-E slot. The options are Enabled and Disabled.
•Operational Firmware Version
Above 4G Decoding (Available if the system supports 64-bit PCI decoding)
•Recovery Firmware Version
Select Enabled to decode a PCI device that supports 64-bit in the space above 4G
Address. The options are Enabled and Disabled.
•ME Firmware Features
SR-IOV (Available if the system supports Single-Root Virtualization)
•ME Firmware Status #1
Select Enabled for Single-Root IO Virtualization support. The options are Enabled
and Disabled.
•ME Firmware Status #2
Maximum Payload
•Current State
Select Auto for the system BIOS to automatically set the maximum payload value for
a PCI-E device to enhance system performance. The options are Auto, 128 Bytes,
256 Bytes, 512 Bytes, 1024 Bytes, 2048 Bytes, and 4096 Bytes.
•Error Code
Altitude
Maximum Read Request
This item indicates the altitude of this machine that is above the sea level. The
value is shown in meters. If the value is unknown, enter the number "80000000".
Select Auto for the system BIOS to automatically set the maximum size for a read
request for a PCI-E device to enhance system performance. The options are Auto,
128 Bytes, 256 Bytes, 512 Bytes, 1024 Bytes, 2048 Bytes, and 4096 Bytes.
MCTP (Management Component Transport Protocol) Bus Owner
This item indicates the location of the MCTP Bus owner. Enter 0's to all fields to
disable the MCTP Bus owner.
ASPM Support
Use this item to set the Active State Power Management (ASPM) level for a PCI-E
device. Select Auto for the system BIOS to automatically set the ASPM level based
on the system configuration. Select Disabled to disable ASPM support. The options
are Disabled and Auto.
Warning: Enabling ASPM support may cause some PCI-E devices to fail!
7-28
7-29
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Chapter 7: BIOS
MMIOHBase
Super
Use this item to select the I/O base memory size according to memory-address
mapping for the PCH chip. The base memory size must be between 4032G to
4078G. The options are 56T, 48T, 24T, 2T, 512G, and 256G.
Super IO Chip AST2400
MMIO High Size
Serial Port 1/Serial Port 2
Use this item to select the high I/O memory size according to memory-address
mapping for the PCH chip. The options are 256G, 128G, 512G, and 1024G.
Select Enabled to enable the onboard serial port specified by the user. The options
are Enabled and Disabled.
PCI Devices Option ROM Setting
Device Settings
CPU1 Slot1 PCI-E x8 OPROM/CPU1 Slot2 PCI-E x16 OPROM/CPU1 Slot3
PCI-E x8 OPROM/CPU2 Slot4 PCI-E x16 OPROM/CPU2 Slot5 PCI-E x8
OPROM/CPU2 Slot6 PCI-E x16 OPROM/CPU2 Slot7 PCI-E x16 OPROM/
Onboard Video Option ROM
Select Enabled to enable Option ROM support to boot the computer using a device installed on the slot specified by the user. The options are Disabled, Legacy,
and EFI.
Onboard LAN Option ROM Type
Select Enabled to enable Option ROM support to boot the computer using a device
installed on the slot specified by the user. The options are Legacy and EFI.
VGA Priority
Use this item to select the graphics device to be used as the primary video display
for system boot. The options are Onboard and Offboard.
Onboard LAN1 Option ROM/Onboard LAN2 Option ROM
Use this option to select the type of device installed in LAN Port1 or LAN Port2
for system boot. The default setting for LAN1 Option ROM is PXE, and for LAN2
Option ROM is Disabled.
Network Stack
Select Enabled to enable PXE (Preboot Execution Environment) or UEFI (Unified Extensible Firmware Interface) for network stack support. The options are
Enabled and Disabled.
IO Configuration
Serial Port 1 Configuration/Serial Port 2 Configuration
This item displays the base I/O port address and the Interrupt Request address for
a serial port specified by the user. The default setting for Serial Port 1 is IO=3F8h
IRQ=4; for Serial Port 2 is IO=2F8h, IRQ=3.
Change Port 1 Settings/Change Port 2 Settings
This feature specifies the base I/O port address and the Interrupt Request address
of Serial Port 1 or Serial Port 2. Select Auto for the BIOS to automatically assign
the base I/O and IRQ address to a serial port specified.
The options for Serial Port 1 are Auto, (IO=3F8h; IRQ=4), (IO=3F8h; IRQ=3, 4, 5,
6, 7, 10, 11, 12), (IO=2F8h; IRQ=3, 4, 5, 6, 7, 10, 11, 12); (IO=3E8h; IRQ=3, 4, 5,
6, 7, 10, 11, 12), and (IO=2E8h; IRQ=3, 4, 5, 6, 7, 10, 11, 12).
The options for Serial Port 2 are Auto, (IO=2F8h; IRQ=3), (IO=3F8h; IRQ=3, 4, 5,
6, 7, 10, 11, 12), (IO=2F8h; IRQ=3, 4, 5, 6, 7, 10, 11, 12); (IO=3E8h; IRQ=3, 4, 5,
6, 7, 10, 11, 12), and (IO=2E8h; IRQ=3, 4, 5, 6, 7, 10, 11, 12).
Device Mode
Use this item to select the SUART Clock source for a serial port specified by the
user. The options are 24MHz/13 and 24MHz.
Serial Port 2 Attribute
Select SOL to use COM Port 2 as a Serial_Over_LAN (SOL) port for console redirection. The options are COM and SOL.
Serial
Port Console Redirection
COM 1
COM 1 Console Redirection
Select Enabled to enable COM Port 1 Console Redirection, which will allow a client
machine to be connected to a host machine at a remote site for networking. The
options are Disabled and Enabled.
7-30
7-31
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
*If the item above set to Enabled, the following items will become available for
configuration:
COM1 Console Redirection Settings
Terminal Type
Use this item to select the target terminal emulation type for Console Redirection. Select VT100 to use the ASCII Character set. Select VT100+ to add color
and function key support. Select ANSI to use the Extended ASCII Character set.
Select VT-UTF8 to use UTF8 encoding to map Unicode characters into one or
more bytes. The options are ANSI, VT100, VT100+, and VT-UTF8.
Chapter 7: BIOS
VT-UTF8 Combo Key Support
Select Enabled to enable VT-UTF8 Combination Key support for ANSI/VT100
terminals. The options are Enabled and Disabled.
Recorder Mode
Select Enabled to capture the data displayed on a terminal and send it as text
messages to a remote server. The options are Disabled and Enabled.
Resolution 100x31
Select Enabled for extended-terminal resolution support. The options are Disabled and Enabled.
Legacy OS Redirection Resolution
Bits Per second
Use this item to set the transmission speed for a serial port used in Console
Redirection. Make sure that the same speed is used in the host computer and the
client computer. A lower transmission speed may be required for long and busy
lines. The options are 9600, 19200, 38400, 57600 and 115200 (bits per second).
Data Bits
Use this item to set the data transmission size for Console Redirection. The
options are 7 (Bits) and 8 (Bits).
Parity
A parity bit can be sent along with regular data bits to detect data transmission
errors. Select Even if the parity bit is set to 0, and the number of 1's in data bits
is even. Select Odd if the parity bit is set to 0, and the number of 1's in data bits
is odd. Select None if you do not want to send a parity bit with your data bits
in transmission. Select Mark to add a mark as a parity bit to be sent along with
the data bits. Select Space to add a Space as a parity bit to be sent with your
data bits. The options are None, Even, Odd, Mark and Space.
Stop Bits
A stop bit indicates the end of a serial data packet. Select 1 Stop Bit for standard
serial data communication. Select 2 Stop Bits if slower devices are used. The
options are 1 and 2.
Use this item to select the number of rows and columns used in Console Redirection for legacy OS support. The options are 80x24 and 80x25.
Putty KeyPad
Use this item to select Function Keys and KeyPad settings for Putty, which is a
terminal emulator designed for the Windows OS. The options are VT100, LINUX,
XTERMR6, SCO, ESCN, and VT400.
Redirection After BIOS Post
Use this item to enable or disable legacy Console Redirection after BIOS POST
(Power-On Self-Test). When "Bootloader" is selected, legacy Console Redirection is disabled before booting the OS. When "Always Enable" is selected, legacy
Console Redirection remains enabled while the OS boots up. The options are
Always Enable and Bootloader.
SOL/COM2
SOL/COM2 Console Redirection
Select Enabled to use the SOL port for Console Redirection. The options are Enabled and Disabled.
*If the item above set to Enabled, the following items will become available for
user's configuration:
Flow Control
Use this item to set the flow control for Console Redirection to prevent data
loss caused by buffer overflow. Send a "Stop" signal to stop sending data when
the receiving buffer is full. Send a "Start" signal to start sending data when the
receiving buffer is empty. The options are None and Hardware RTS/CTS.
7-32
7-33
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Chapter 7: BIOS
SOL/COM2 Console Redirection Settings
VT-UTF8 Combo Key Support
Use this feature to specify how the host computer will exchange data with the client
computer, which is the remote computer used by the user.
Select Enabled to enable VT-UTF8 Combination Key support for ANSI/VT100
terminals. The options are Enabled and Disabled.
Terminal Type
Recorder Mode
Use this feature to select the target terminal emulation type for Console Redirection. Select VT100 to use the ASCII Character set. Select VT100+ to add color
and function key support. Select ANSI to use the Extended ASCII Character Set.
Select VT-UTF8 to use UTF8 encoding to map Unicode characters into one or
more bytes. The options are ANSI, VT100, VT100+, and VT-UTF8.
Select Enabled to capture the data displayed on a terminal and send it as text
messages to a remote server. The options are Disabled and Enabled.
Bits Per second
Use this feature to set the transmission speed for a serial port used in Console
Redirection. Make sure that the same speed is used in the host computer and the
client computer. A lower transmission speed may be required for long and busy
lines. The options are 9600, 19200, 38400, 57600 and 115200 (bits per second).
Data Bits
Resolution 100x31
Select Enabled for extended-terminal resolution support. The options are Disabled and Enabled.
Legacy OS Redirection Resolution
Use this feature to select the number of rows and columns used in Console
Redirection for legacy OS support. The options are 80x24 and 80x25.
Putty KeyPad
Use this feature to set the data transmission size for Console Redirection. The
options are 7 (Bits) and 8 (Bits).
This feature selects Function Keys and KeyPad settings for Putty, which is a
terminal emulator designed for the Windows OS. The options are VT100, LINUX,
XTERMR6, SCO, ESCN, and VT400.
Parity
Redirection After BIOS Post
A parity bit can be sent along with regular data bits to detect data transmission
errors. Select Even if the parity bit is set to 0, and the number of 1's in data bits
is even. Select Odd if the parity bit is set to 0, and the number of 1's in data bits
is odd. Select None if you do not want to send a parity bit with your data bits
in transmission. Select Mark to add a mark as a parity bit to be sent along with
the data bits. Select Space to add a Space as a parity bit to be sent with your
data bits. The options are None, Even, Odd, Mark and Space.
Use this feature to enable or disable legacy Console Redirection after BIOS
POST (Power-On Self-Test). When this feature is set to Bootloader, legacy
Stop Bits
A stop bit indicates the end of a serial data packet. Select 1 Stop Bit for standard
serial data communication. Select 2 Stop Bits if slower devices are used. The
options are 1 and 2.
Flow Control
Use this feature to set the flow control for Console Redirection to prevent data
loss caused by buffer overflow. Send a "Stop" signal to stop sending data when
the receiving buffer is full. Send a "Start" signal to start data-sending when the
receiving buffer is empty. The options are None and Hardware RTS/CTS.
7-34
Console Redirection is disabled before booting the OS. When this feature is set
to Always Enable, legacy Console Redirection remains enabled upon OS boot.
The options are Always Enable and Bootloader.
Legacy Console Redirection
The submenu allows the user to configure Legacy Console Redirection settings so
that legacy devices can be used for Console Redirection.
Legacy Console Redirection Settings
Use this feature to specify how the host computer will communicate with the client
compute at a remote site via legacy devices.
Legacy Serial Redirection Port
The feature selects a legacy serial port to be used for Console Redirection. The
options are COM1 Console Redirection and COM2/SOL Console Redirection.
7-35
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Serial Port for Out-of-Band Management/Windows Emergency Management
Services (EMS)
The submenu allows the user to configure Console Redirection settings to support
Out-of-Band Serial Port management.
(EMS) Console Redirection
Select Enabled to use a COM port selected by the user for EMS Console Redirection. The options are Enabled and Disabled.
*If the item above set to Enabled, the following items will become available for
user's configuration:
EMS Console Redirection Settings (Available when EMS
Console Redirection is enabled)
Use this feature to specify how the host computer will exchange data with the client
computer, which is the remote computer used by the user.
Out-of-Band Management Port
The feature selects a serial port in a client server to be used by the Windows
Emergency Management Services (EMS) to communicate with a remote host
server. The options are COM1 (Console Redirection) and COM2/SOL (Console
Redirection).
Chapter 7: BIOS
The following settings will be displayed:
Data Bits, Parity, Stop Bits
Enabling TPM in the BIOS
The steps below describe the proper procedure on how to enable the TPM in the
BIOS. This process is necessary to activate support in the system before you can
start using the TPM.
1. Enter the BIOS setup screen. You may do this either from the IPMI remote
console or from the server directly using KVM. Reboot the system and press
the <Del> key as the system boots until you reach the BIOS screen.
2. You will be presented with the BIOS setup main screen. Using the arrow
keys, navigate to the Advanced tab. From there, navigate down and select the
"CPU Configuration" option as shown below. Press <Enter>.
3. You will be taken to the CPU Configuration page. Using the arrow keys, navigate down to the "Intel Virtualization Technology" option and press <Enter>.
Select "Enable" and press <Enter>.
Terminal Type
Use this feature to select the target terminal emulation type for Console Redirection. Select VT100 to use the ASCII character set. Select VT100+ to add color
and function key support. Select ANSI to use the extended ASCII character set.
Select VT-UTF8 to use UTF8 encoding to map Unicode characters into one or
more bytes. The options are ANSI, VT100, VT100+, and VT-UTF8.
Bits Per Second
This item sets the transmission speed for a serial port used in Console Redirection. Make sure that the same speed is used in both host computer and the client
computer. A lower transmission speed may be required for long and busy lines.
The options are 9600, 19200, 57600, and 115200 (bits per second).
Flow Control
Use this item to set the flow control for Console Redirection to prevent data
loss caused by buffer overflow. Send a "Stop" signal to stop data-sending when
the receiving buffer is full. Send a "Start" signal to start data-sending when
the receiving buffer is empty. The options are None, Hardware RTS/CTS, and
Software Xon/Xoff.
7-36
4. Once you have enabled virtualization support, press your <Esc> key until you
are back to the Advanced tab. Navigate down to the "Trusted Computing"
option and press <Enter>.
5. The Trusted Computing window will appear. Select "TPM State" and press
<Enter>.
7-37
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
6. From the window that pops up, select "Enabled" and press <Enter>.
Chapter 7: BIOS
ACPI
Settings
WHEA Support
Select Enabled to support the Windows Hardware Error Architecture (WHEA) platform and provide a common infrastructure for the system to handle hardware errors
within the Windows OS environment to reduce system crashes and to enhance
system recovery and health monitoring. The options are Enabled and Disabled.
High Precision Event Timer
Select Enabled to activate the High Precision Event Timer (HPET) that produces
periodic interrupts at a much higher frequency than a Real-time Clock (RTC) does in
synchronizing multimedia streams, providing smooth playback and reducing the dependency on other timestamp calculation devices, such as an x86 RDTSC Instruction embedded in the CPU. The High Performance Event Timer is used to replace
the 8254 Programmable Interval Timer. The options are Enabled and Disabled.
NUMA (Available when the OS supports this feature)
7. You must save your changes and reset for the changes to take effect. Scroll
to the Save & Exit tab and select "Save Changes and Reset." The TPM is
now enabled.
Select Enabled to enable Non-Uniform Memory Access support to enhance system
performance. The options are Enabled and Disabled.
iSCSI Configuration
Intel
TXT (LT-SX) Configuration
This submenu allows the user to configure the following TXT settings.
TXT Support
Select Enabled to enable Intel Trusted Execution Technology (TXT) support. The
options are Disabled and Enabled.
Note: If the option for this item (TXT Support) is set to Enabled, be sure
to disable EV DFX (Device Function On-Hide) support for the system to
work properly. (EV DFX is under "IIO Configuration" in the "Chipset/North
Bridge" submenu on Page 4-11).
Note: For more information on TPM, please refer to the TPM manual at
http://www.supermicro.com/manuals/other/AOM-TPM-9655V_9655H.pdf
7-38
This item displays iSCSI configuration information:
iSCSI Initiator Name
Use this item to enter the name of the iSCSI Initiator, which is a unique name
used in the world. The name must in the IQN format. The following submenu
will be available for configuration:
Add an Attempt
Delete Attempts
Change Attempt Order
7-39
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
7-4 Event Logs
Chapter 7: BIOS
When Log is Full
This submenu allows the user to configure Event Log settings.
Select Erase Immediately to immediately erase all errors in the SMBIOS event log
when the event log is full. Select Do Nothing for the system to do nothing when
the SMBIOS event log is full. The options are Do Nothing and Erase Immediately.
SMBIOS Event Log Standard Settings
Log System Boot Event
Select Enabled to log system boot events. The options are Disabled and Enabled.
MECI (Multiple Event Count Increment)
Enter the increment value for the multiple event counter. Enter a number between
1 to 255. The default setting is 1.
METW (Multiple Event Count Time Window)
This item is used to determine how long (in minutes) the multiple event counter
should wait before generating a new event log. Enter a number between 0 to 99.
The default setting is 60.
Change SMBIOS Event Log Settings
Note: Please reboot the system for the changes to take effect.
This feature allows the user to configure SMBIOS Event settings.
View SMBIOS Event Log
Enabling/Disabling Options
This item allows the user to view the event in the SMBIOS event log. The following
categories are displayed:
SMBIOS Event Log
Select Enabled to enable SMBIOS (System Management BIOS) Event Logging
during system boot. The options are Enabled and Disabled.
Date/Time/Error Code/Severity
BMC (Baseboard Management Controller) Firmware Revision
This item indicates the BMC firmware revision used in your system.
Runtime Error Logging Support
Select Enable to support Runtime Error logging. The options are Enabled and
Disabled. If this item is set to Enabled, the following item will be available for
configuration:
Status of BMC
This item indicates the status of the onboard BMC chip installed in your system.
Erasing Settings
Erase Event Log
Select Yes to erase all error events in the SMBIOS (System Management BIOS)
log before an event logging is initialized at bootup. The options are No, Yes, Next
reset, and Yes, every reset.
7-40
7-41
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
7-5 IPMI
Chapter 7: BIOS
BMC Network Configuration
This submenu allows the user to configure Intelligent Platform Management Interface (IPMI) settings.
The following items will be displayed:
•IPMI LAN Selection
•IPMI Network Link Status
Update IPMI LAN Configuration
Select Yes for the system BIOS to automatically reset the following IPMI settings
upon next system boot. The options are Yes and No.
Configuration Address Source (Available when the item above - Update
IPMI LAN Configuration is set to Yes)
Use this item to select the IP address source for this computer. If Static is selected,
you will need to know the IP address of this computer and enter it to the system
manually in the field. If DHCP is selected, AMI BIOS will search for a DHCP (Dynamic Host Configuration Protocol) server attached to the network and request
the next available IP address for this computer. The options are DHCP and Static.
Station IP Address
System Event Log
This item displays the Station IP address for this computer. This should be in decimal
and in dotted quad form (i.e., 192.168.10.253).
Enabling/Disabling Options
Subnet Mask
SEL Components
This item displays the sub-network that this computer belongs to. The value of each
three-digit number is separated by dots and it should not exceed 255.
Select Enabled to enable all system event logging support at bootup. The options
are Enabled and Disabled.
Station MAC Address
This item displays the Station MAC address for this computer. Mac addresses are
6 two-digit hexadecimal numbers.
Erasing Settings
Erase SEL
Select Yes, On next reset to erase all system event logs upon next system reboot.
Select Yes, On every reset to erase all system event logs upon each system reboot.
Select No to keep all system event logs after each system reboot. The options are
No, Yes, On next reset, and Yes, On every reset.
Gateway IP Address
This item displays the Gateway IP address for this computer. This should be in
decimal and in dotted quad form (i.e., 192.168.10.253).
When SEL is Full
This feature allows the user to determine what the AMI BIOS should do when the
system event log is full. Select Erase Immediately to erase all events in the log when
the system event log is full. The options are Do Nothing and Erase Immediately.
Note: After making changes on a setting, be sure to reboot the system for
the changes to take effect.
7-42
7-43
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
7-6 Security Settings
Chapter 7: BIOS
7-7 Boot Settings
This submenu allows the user to configure the following security settings for the
system.
This submenu allows the user to configure Boot settings for this system:
Boot Configuration
Administrator Password
Boot Mode Select
Use this feature to set the administrator password which is required before entering
the BIOS setup utility. The length of the password should be from 3 characters
to 20 characters long.
Use this item to select the type of device to be used for system boot. The options
are Legacy, UEFI, and Dual.
User Password (Available after an Administrator Password is entered)
Use this feature to set the user password which is required to enter the BIOS
setup utility. The length of the password should be from 3 characters to 20 characters long.
Fixed Boot Order Priorities
This option prioritizes the order of bootable devices from which the system will boot.
Press <Enter> on each entry from top to bottom to select devices.
When the item above -"Boot Mode Select" is set to Dual (default), the following
items will be displayed for configuration:
•Boot Option
#1 - Boot Option #15
When the item above -"Boot Mode Select" is set to Legacy, the following items will
be display for configuration:
•Boot Option
#1 - Boot Option #7
When the item above -"Boot Mode Select" is set to UEFI, the following items will
be display for configuration:
•Boot Option #1 - Boot Option
#8
Delete Boot Option
Use this item to select a boot device to delete from the boot priority list.
7-44
7-45
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Chapter 7: BIOS
Delete Boot Option
Discard Changes and Exit
Select the target boot device to delete from the boot priority list.
Select this item to exit from the BIOS setup without making any permanent changes
to the system configuration, and reboot the computer.
Delete Driver Option
Use this item to select a driver to delete from the boot priority list.
Delete Boot Option
Select the target boot drive to delete from the boot priority list.
Hard Disk Drive BBS Priorities
•Boot Option #1
Save Changes and Reset
When you have completed the system configuration changes, select this item to
leave the BIOS setup utility and reboot the computer for the new system configuration parameters to take effect. Select Yes and press <Enter> to save the changes
you've made and reboot the system.
Save Options
Save Changes
Network Drive BBS Priorities
When you have completed the system configuration changes, select this item to
save all changes made. This will not reset (reboot) the system.
•Boot Option #1
Discard Changes
UEFI Application Boot Priorities
Select this item to discard all the changes and return to the AMI BIOS setup utility.
Select Yes and press <Enter> to discard all changes made.
•UEFI Boot Option #1
Restore Defaults
7-8 Save & Exit
This submenu allows the user to configure the following Save & Exit settings:
Select this item and press <Enter> to load the manufacture default settings which
are designed for maximum system performance but not for maximum stability.
Save As User Defaults
Select this item and press <Enter> to save the current BIOS settings as user's
default settings for future use.
Restore User Defaults
Select this item and press <Enter> to retrieve the user-defined default settings that
were previously saved to be used as current default settings.
Boot Override
This feature allows the user to override the boot priority sequence in the Boot submenu and immediately boot the system with another device specified by the user.
This is a one-time override.
7-46
7-47
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Notes
7-48
Appendix A: BIOS POST Error Codes
Appendix A
BIOS POST Error Codes
During the POST (Power-On Self-Test) routines, which are performed upon each
system boot, errors may occur.
Non-fatal errors are those which, in most cases, allow the system to continue to
boot. These error messages normally appear on the screen.
Fatal errors will not allow the system to continue with bootup. If a fatal error occurs,
you should consult with your system manufacturer for possible repairs.
These fatal errors are usually communicated through a series of audible beeps.
The numbers on the fatal error list correspond to the number of beeps for the corresponding error.
Motherboard BIOS Error Beep Codes
Beep Code/LED
Error Message
Description
1 beep
Refresh
Ready to boot
5 short beeps + 1 long beep
Memory error
No memory detected in the
system
5 beeps
1 beep per device
No con-in or con-out
devices
Con-in includes USB or PS/2
keyboard, PCI or serial console
redirection, and IPMI KVM or
SOL.
Con-out includes the video
controller, PCI or serial console
redirection, and IPMI SOL.
1 beep for each USB device
detected
Refresh
IPMI Error Codes
1 Continuous beep
System OH
A-1
System overheat
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Notes
A-2
Appendix B: System Specifications
Appendix B
System Specifications
Processors
Single or dual Intel® Xeon E5-2600 (v3/v4) Series processors
Note: Please refer to our web site for a complete listing of supported processors.
Chipset
Intel C612 chipset
BIOS
16 Mb AMI® SPI Flash ROM
Memory Capacity
Sixteen DIMM sockets supporting up to 2 TB of Load Reduced (LRDIMM) or 1
TB of Registered (RDIMM) ECC DDR4-2400/2133/1866/1600 memory
Note: see Section 5-6 for details.
Drive Bays
Twenty-four hot-swap drive bays to house SATA or SAS hard drives
Expansion Slots
Six PCI-Express 3.0 x8 slots and one PCI-Express 3.0 x16 slot
Serverboard
X10DRH-iT (Extended ATX form factor)
Dimensions: 13.68 x 13.05 in (347.5 x 331.5 mm)
Chassis
SC846BE1C-R920B (4U rackmount)
Dimensions: (WxHxD) 17.2 x 7 x 26.5 in. (437 x 178 x 673 mm)
B-1
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
Appendix B: System Specifications
Notes
Weight
Gross Weight: 52 lbs. (23.6 kg.)
System Cooling
Three 8-cm system fans and two 8-cm exhaust fans
System Input Requirements
AC Input Voltage: 100 - 240V AC auto-range
Rated Input Current: 10.7 - 4.2A max
Power Supply
Rated Output Power: 920W (Part# PWS-920P-1R)
Rated Output Voltages: +12V (75A), +5Vsb (4A)
Operating Environment
Operating Temperature: 10º to 35º C (50º to 95º F)
Non-operating Temperature: -40º to 70º C (-40º to 158º F)
Operating Relative Humidity: 8% to 90% (non-condensing)
Non-operating Relative Humidity: 5% to 95% (non-condensing)
Regulatory Compliance
Electromagnetic Emissions: FCC Class A, EN 55022 Class A, EN 61000-3-2/-3-3,
CISPR 22 Class A
Electromagnetic Immunity: EN 55024/CISPR 24, (EN 61000-4-2, EN 61000-4-3,
EN 61000-4-4, EN 61000-4-5, EN 61000-4-6, EN 61000-4-8, EN 61000-4-11)
Safety: CSA/EN/IEC/UL 60950-1 Compliant, UL or CSA Listed (USA and
Canada), CE Marking (Europe)
California Best Management Practices Regulations for Perchlorate Materials:
This Perchlorate warning applies only to products containing CR (Manganese
Dioxide) Lithium coin cells. “Perchlorate Material-special handling may apply. See
www.dtsc.ca.gov/hazardouswaste/perchlorate”
B-2
B-3
SUPERSTORAGESYSTEM 6048R-E1CR24H User's Manual
(continued from front)
The products sold by Supermicro are not intended for and will not be used in life support systems,
medical equipment, nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency communication devices or other critical systems whose failure to perform be reasonably expected to
result in significant injury or loss of life or catastrophic property damage. Accordingly, Supermicro disclaims any and all liability, and should buyer use or sell such products for use in such ultra-hazardous
applications, it does so entirely at its own risk. Furthermore, buyer agrees to fully indemnify, defend
and hold Supermicro harmless for and against any and all claims, demands, actions, litigation, and
proceedings of any kind arising out of or related to such ultra-hazardous use or sale.
B-4
Download PDF
Similar pages