22" FHD LED TV with DVB-T2/-S2 & DVD-Player
Model No.:LED-2208
Contents
Caution
1
Safety Information
2
Accessories
3
Product Introduction
4
Connections
5
Remote Control
6-7
Basic Operation
8
OSD Menu
1. Picture menu
2. Sound menu
3. Channel menu
4. Feature menu
5. Setup menu
9-17
9
10
11-14
15-16
17
Multimedia Operation
18-20
Recording Operation
21-23
DVD Operation
24-31
Simple Troubleshooting
32
Caution
The lightning flash with arrowhead symbol, within an equilateral triangle
is intended to alert the user to the presence of un-insulated “dangerous
voltage” within the products enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to the persons.
The exclamation point within an equilateral triangle is intend to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
Correct disposal of this Product
(Waste Electrical & Electronic Equipment (WEEE)
Your product is designed and manufactured with high quality materials and
components which can be recycled and reused.
This symbol means that electrical and electronic equipment, at their endof-life should be disposed of separately from your household waste.
Please dispose of this equipment at your local community waste collection/
recycling center.
In the USA there are separate collection systems for used electrical and
electronic products. Please help us to conserve the environment we live in!
directives.
This unit complies with The Restriction of the use of certain Hazardous
substances in Electnical and Electronic Equipment
1
Safety Information
To ensure reliable and safe operation of this equipment, please read carefully all the
instructions in this user guide, especially the safety information below.
Electrical safety
• To prevent overload, don't share the same mains supply socket with too many other
items of equipment.
- Do not place any connecting wires where they may be stepped on or tripped over.
- Do not place heavy items on the leads, which may damage them.
- Hold the Mains plug, not the wires, when removing from a socket.
- During a thunderstorm or while leaving the TV for long periods, disconnect the aerial
(if outdoor) and mains power from the supply.
- Do not allow water or moisture to enter the TV . Do NOT use in wet
or moist areas such as Bathrooms, steamy kitchens or near swimming pools.
• Pull the plug out immediately, and seek professional help if:
- the mains plug or cable is damaged.
- liquid is spilt onto the set, or if it is accidentally exposed to water or moisture.
- anything accidentally penetrates the ventilation slots.
- the set does not work normally.
- Do NOT remove the safety covers. There are no user serviceable parts inside.
You may invalidate the warranty. Qualified personnel only are permitted to service
this apparatus.
- To avoid battery leakage, remove exhausted batteries from the remote control
handset, or when not using for along period.
- Do NOT break open or throw exhausted batteries on a fire.
Physical safety
• Do NOT block ventilation slots in the back cover. You may place the TV in a cabinet,
but ensure at least 5cm (2") clearance all around the unit.
• Do NOT tap or shake the TV screen, you may damage the internal circuitry. Take good
care of the remote control, do not drop it or allow it to come into contact with liquids.
• To clean the TV use a soft dry cloth. Do NOT use solvents or petrol based fluids. For
stubborn stains, you may use a damp soft cloth with diluted detergent.
2
Accessories
PICTURE
ASPECT
SLEEP
SOUND
2
3
4
5
6
7
8
9
FAV
0
D
IS
PL
T
PU
IN
AY
1
EX
IT
U
EN
M
EPG
TV/RADIO
VOL
Adapter
CH
REC
SUBTITLE
CH.LIST
TV/TXT
D.PRO
CANCEL
D.REP
REVEAL
D.GOTO
INDEX
HOLD
SIZE
D.ZOOM
SUBPAGE
D.SET
D.MENU
D.SUB
D.LAN
REC.LIST
NICAM/A2
D.SLOW
D.TITLE
User’s Guide
Remote Control
E-35D
Mini YPbPr cable
Mini AV cable
Batteries
* Note: The configuration of the components may look different from the following illustration
Technical Specification
- TV System
- Screen Size
- Resolution
PAL BG/DK/I SECAM BG/DK L/L’
22 inch(diagonal)
1920x 1080
- Aerial input
- Audio output power
- Power Consumption
2x3W
12V
Remote Control
Type
Control distance
infrared
5m
Control angle
Batteries
30 0 (horizontal)
2 x 1.5V, size AAA
3A 36W
3
Product Introduction
Front View
Insert disc with label side towards back
Remote Control window
(IR) Infrared Receiver: Receives IR signals from the remote control.
(Power on/Standby) LED indicator: Press
to turn on and off.
Indicator on(Red)
Standby mode
Indicator on(Green)
Power on mode
The effective receiving range for the signal is 5-8 metres from the front of the remote
control window, and 300 to the left or right side and 200 above or below the control
window.
INPUT: Display the input source menu.
MENU: Display/exit the OSD menu.
CH+/-: Scan through channels.
VOL+/-: Adjust the volume.
PLAY: Play/pause the disc playing.
EJECT: Eject the disc
:Turn on/standby the TV set.
4
USB Headphone out
Mini YPbPr
Mini AV
Common Interface
Connections
POWER
VGA
PC in
SCART
DVB-S2
RF
COAX
HDMI
Main Power Switch
To switch on/off the TV
POWER: Connect to the mains adaptor.
VGA: For PC display.Connect it to the D-Sub 15 pins analog output connector of the PC.
PC in: Connect it to the audio output terminal of PC.
SCART: Connect them to the SCART video output terminal of DVD.
DVB-S2: Connect a Satellite signal.
RF: Connect antenna or cable 75 Ohm coaxial to receive TV signal.
Coax: Digital output to AV receiver.
HDMI: Connect it to the HDMI of DVD or other equipment.
USB: Connect to USB device for multimedia and PVR.
Headphone: Connect it to your headphone or other audio equipment.
Common Interface: CI slot.
Mini YPbPr: Connect it to the YPbPr video output terminal of DVD with the Converter cable.
Mini AV: Connect it to the audio & video output terminal of DVD with the Converter cable.
(Audio terminals are shared with YPbPr)
5
Remote Control
The remote control is using Infra-Red(IR). Point it towards the front of the LED TV. The remote
control may not work correctly if it is operated out of range or out of angle.
PICTURE
ASPECT
SLEEP
SOUND
2
3
4
5
6
7
8
9
FAV
0
PL
D
T
IS
PU
U
EX
EN
IT
M
EPG
TV/RADIO
VOL
CH
REC
SUBTITLE
CH.LIST
TV/TXT
D.PRO
CANCEL
D.REP
REVEAL
D.GOTO
INDEX
HOLD
SIZE
D.ZOOM
SUBPAGE
D.MENU
D.SUB
D.LAN
D.SET
NUMBER BUTTONS
Press 0-9 to select a TV channel directly when you
are watching TV.
Return to the previous channel viewed.
IN
AY
1
POWER: Turn the TV on/standby.
MUTE: Press to mute the sound, press again or press
VOL+ to unmute.
PICTURE: Select the picture mode.
ASPECT: Change the screen display mode.
SLEEP: Standby timer.
SOUND: Select the sound mode.
FAV: Display the favorite program list.
REC.LIST
DISPLAY: Press to display the current mode’s information.
INPUT: Press to display the input source menu.
MENU: System setup menu.
EXIT: Exit the OSD menu.
CURSOR KEYS
OK
Allows you to navigate the on-screen menus and adjust the
system settings to your preference.
VOL+/-: Adjust the volume.
CH / : Scan through channels.
EPG: To show the Electronic Program Guide during no-menu
state only in DTV mode.
TV/RADIO: Switch to TV/RADIO.
: Load/eject DVD disc.
NICAM/A2
D.SLOW
D.TITLE
6
Remote Control
PICTURE
ASPECT
SLEEP
SOUND
1
2
3
4
5
6
PVR/DVD
REC : Press to start record the program in DTV mode.
: Play/Pause program.
8
7
9
: Next chapter.
: Stop program.
: Fast reverse.
: Fast forward.
0
D
T
IS
PU
PL
IN
AY
FAV
U
EX
EN
IT
M
EPG
TV/RADIO
VOL
CH
REC
SUBTITLE
CH.LIST
TV/TXT
D.PRO
CANCEL
D.REP
REVEAL
D.GOTO
INDEX
HOLD
SIZE
D.ZOOM
SUBPAGE
D.MENU
D.SUB
D.LAN
D.SET
: Previous chapter.
REC.LIST
NICAM/A2
D.SLOW
D.TITLE
SUBTITLE: Turn on/off the subtitle display in DTV mode.
CH.LIST: Display the channel list.
REC.LIST:Record List.
TV.TXT:Turn off/on the Teletext display.
CANCEL: Cancel the Teletext display.
REVEAL: Reveal any hidden text.
NICAM/A2: TV Nicam/A2 select.
INDEX: Go to index.
HOLD: Hold or carry on the current subpage.
SIZE: Press to see top half of page double size,
Press again to see the bottom half of page
double size. Press again for normal size.
SUBPAGE: Press to enter subpages, pressagain to cancel.
D.PRO Edit the program and play.
D.REP Repeat playing the title or chapter.
D.GOTO Play your favorite title/chapter/track.
D.SLOW Play DVD programs at slow speed.
D.ZOOM: Adjust picture size in DVD mode.
D.TITLE:DVD title.
D.SET: DVD system setup.
D.MENU: DVD play list/Disc menu.
D.SUB: Turn on/off the subtitle display in DVD mode.
D.LAN: Select DVD disc language.
7
Basic Operation
Power on/off
1. Connect to the power supply with the adaptor.
2. -To turn on the TV
Press button on the TV or remote control.
-To turn off the TV
Press button on the TV or remote control.
Input Source select
Press INPUT button on the TV set or remote control to display the
input source menu, and use CH+/- button on the TV set or Ĥ0ĥ!button
on remote control to select the input source, press OK button on the
remote control to enter.
Note: Before you select the input source, make sure the
connections are prepared.
Basic OSD Menu operation
Press MENU button to display the OSD menu as below:
Main menu: Picture Sound Channel Feature Setup
Submenu
(Picture menu
for example)
ĥ
Hint---you should operate
the OSD menu according
to the hint.
Use Ĥ / ĥ button to select the main menu, and press
/ OK button to enter the submenu.
In the submenu, use Ĥ / ĥ button to select the function item, press / OK button to enter
the setup menu, then press / button to adjust, or press Ĥ / ĥ to select and press OK /
/ button to confirm.
* (Press MENU / button to return to the upper menu.)
* (Press EXIT button to exit the menu display.)
Note1: Only when you input the suitable signal, the relevant items can be activated
Note2: Please operating the OSD menu according to hint on the bottom of the banner.
8
OSD Menu
1. Picture menu
Description
Picture Mode: Select your desired picture mode from Dynamic, Standard, Mild and User.
Brightness: Adjust image black level.
Contrast: Adjust image contrast.
Sharpness: Adjust the sharpness(Gray and invalid in VGA/PC mode).
Colour: Adjust image colour from black and white.
Tint: Control the tint ( NTSC mode only).
Colour Temp.: Select an optimum color temperature mode to suit your eyes for viewing from
Warm, Cool, Standard.
Aspect Ratio: Change the aspect for the screen from 4:3,16:9,Zoom1,Zoom2 or Panorama etc....
Noise Reduction: If the broadcast signal received is weak, you can select the Noise Reduction
option to reduce the video noise level between Off, Low, Middle and High.
9
OSD Menu
2. Sound menu
Audio Description
ENTER
Description
Sound Mode: Select your desired sound mode from Standard, Movie, Music, Speech and User.
Bass: Adjust the level of the lower-pitched sounds.
Treble: Adjust the level of the higherpitched sounds.
Balance: Adjust the audio output between left and right speakers.
Surround: Turn on/off the surround sound function.
Auto Volume Level (AVL): The volumes of all sources will be maintained when the function’s on.
SPDIF: Select the spdif mode for the TV from off, PCM and Auto.
Audio Description: Enter the Audio Description menu to turn on / off the the
function and adjust the volume.
10
OSD Menu
3. Channel menu(In ATV/DTV mode)
OK
Channel Management: Enter the Channel management menu to edit the channels.
Move
Delete: Press RED button to sign the channels you want to delete, it will hint you when you exit.
Lock: User must set the “Lock enable”(Feature-Lock- Lock enable) at ON to active this function.
Press GREEN button to sign(lock) or cancel(unlock) the channel. And you have to enter the
password to view the program.
Skip: Press YELLOW button to skip the channel or cancel the setting, and the program will not be
programed by CH+/- button.
Swap: Press BLUE button to sign the channel, press /
button to move, and press OK button to
swap the position.
Favorite Management: Add or remove
favourite channels by the colour buttons.
Up to 4 favourite lists are available,
RED-Fav1, GREEN-Fav2, YELLOW-Fav3,
BLUE-Fav4.
11
OSD Menu
Country: Select the country.
TV Connection: Select DTV type, you can choose Air(DVB-T), Cable(DVB-C), Satellite(DVB-S2),
as you like.
Auto Search: Press OK button to enter the Auto Search menu, select search mode, and press
OK button to start auto search.
Note:
1. ALL: Auto search channels for DTV, ATV and
Radio.
DTV: Auto search channels for DTV and radio.
ATV: Auto search channels for ATV.
2. When the TV is auto tunning, you could
press MENU button to stop auto tunning and
return to preview menu.
DTV Manual Search : Enter the DTV Manual Search menu.
Press
button to select the “Channel” item, and press
then press
button to select the “Start” item, and press
DVB-T
ATV Manual Search : Enter the ATV Manual Search menu.
button to select the channel,
button to manual search.
DVB-C
Current Channel: Select the current channel for manual searching.
Search: Press OK button to enter the search menu, and manual search the frequency
by
button.
Fine Tune: Press OK button to enter the Fine tune menu, and fine tune the frequency
by
button.
Color/Sound System: Select the Color/Sound system for the program.
12
OSD Menu
Satellite System
Press
button to select the “TV Conection” , and set it on “Satellite”.
OK
Select “Auto Search” as follow:
Operations in satellite Auto Search menu are shown in the following table
Value
Option
Mode
Default,Network Search,Full Search
Satellite
65 satellite for searching(3 user edit satellite)
Service Type
All Services,Free Service
Channel Type
All, TV Only
13
OSD Menu
Satellite System
Press
button to select the “TV Conection” , and set it on “Satellite”.
OK
Press
button to select the “Satellite System” , show as follow:
Operations in Satellite List Menu are shown in the following table:
Key Stroke
KEY_UP
KEY_DOWN
KEY_LEFT
Action
use cursor to up
use cursor to down
KEY_RIGHT
switch operation to satellite system parameters setting list
switch operation to Transponder list
KEY_MENU
KEY_EXIT
Exit Main Menu.
KEY_GREEN
Enter satellite edit menu
Back to Main Menu.
Operations in Transponder List Menu are shown in the following table:
Key Stroke
Action
KEY_UP
KEY_DOWN
KEY_LEFT
KEY_RIGHT
KEY_ENTER
KEY_MENU
KEY_EXIT
KEY_RED
KEY_GREEN
KEY_YELLOW
KEY_BLUE
use cursor to up
use cursor to down
switch operation to Satellite list
switch operation to satellite system parameters setting list
Select/unselect cursor item Transponder.
Back to Satellite list.
Exit Main Menu.
Enter Transponder Add menu
Enter Transponder Edit menu
Enter Transponder Delete confirm menu
Enter Transponder scan menu
Operations in Setting Menu are shown in the following table:
Key Stroke
Action
KEY_UP
KEY_DOWN
use cursor to up
use cursor to down
KEY_MENU
Back to Transponder liat.
KEY_EXIT
Exit Main Menu.
Option
LNB Power
22KHz
DisEqC Mode
Off,LNB1,LNB2,LNB3,LNB4,Burst A,Burst B
Motor
None,DisEqC1.2,DisEqC1.3
LNB Type
5V antenna power
Turn on / off the 5V antenna power output.
Value
9750/10600,9750/10750,05150,05750,09750,
10600,10750,11300,11475,User Single,User
Dual
On,Off
Auto,off,on
14
OSD Menu
4. Feature menu
Lock: This menu allows you to lock certain features of the television so that they can not be used
or viewed. For example if you don’t want certain channels viewed by children or if the television
is to be used in a hotel and you want certain channels be locked.
When you enter the system lock menu you will be asked for a password. As default it is 0000.
Channel
Lock Channel - Turn on/off the Lock functions.
Note: When it is be turned on, the functions of Parental Guidance and Change Pin code
below will be locked, and the functions Lock(in Channel Management), Auto Search, DTV
Manual Search, ATV manual Search in Channel menu will also be locked.
Parental Guidance - Select the Parental Guidance mode, or turn off the function.
Change Pin Code – Press OK button to enter , first enter the current code, then enter your
new code and confirm your new code.
15
OSD Menu
Hotel Mode - Enter the Hotel Setting menu.
Hotel Lock: Turn on/off the Hotel Lock function.
Channel Lock: Disable the Channel menu in OSD.
Picture Lock: Disable the Picture menu in OSD.
Sound Lock: Disable the Sound menu in OSD.
Feature Lock: Disable the Feature menu in OSD.
Setup Lock: Disable the Setup menu in OSD.
Key Lock: Disable the buttons on the TV set.
Source Lock: Disable the input source you desired.
Set Source: Select the default source when you turn on the TV.
Channel Number: Select the default channel number when you
turn on the TV.
Max Volume: Set the Max volume for the TV.
Default Volume: Set the default volume when the program is on.
Clear Lock: Clear all the locks above, it means set all the locks to
OFF and max volume to 100.
Database Export: Export all Hotel Settings to the USB device.
Database Import: Import all Hotel Settings from the USB device.
Prevlous Page: Select Previous Page items, press the ok button to return to the previous page.
Language: Lets you adjust the different language options available.
Clock: Allows you to set the clock (as default the information is taken automatically from the
digital signal).
Sleep Timer: Lets you set the sleep timer so the television automatically switches off after a
certain amount of time.
Auto Power Off: The TV will switch off itself automatically if no change in status within the
time you select. You can choose 1H, 2H, 4H or off.
Hearing Impaired: You can switch on the hearing impaired feature, this provides additional
information and subtitles
CI Info: Pay per view services require a “smartcard” to be inserted into the TV.
If you subscribe to a pay per view service the provider will issue you with a ‘CAM’ and a
“smartcard”. The CAM can then be inserted into the COMMON INTERFACE PORT
(CI Card In).
PVR/Timeshift: Setup menu for recording, please see the Recording Operation section.
16
OSD Menu
5. Setup menu
OK
Description
OSD Timer: Lets you adjust the amount of time the On Screen Menu stays on the screen
before disappearing.
Auto SCART: The TV will be changed to SCART source automatically when you connect the
TV to the SCART device.
PC Setup: Change the PC Settings in PC mode.
Auto Adjust: Setup the parameter of the screen automatically.
H/V-Position: Adjust the transverse/vertical position of the screen.
Phase: Adjust the phase of the ADC sampling clock relative to the sync signal, until a
stable image is obtained.
Clock: Adjust the pixel clock frequency, until the image size is maximized for the screen.
Blue Screen: Changes the background when there is no input between clear and a blue
background (Only available in some sources).
Home Mode: Press to select from the following home modes:Home,Dynamic.
Reset TV Setting - This clears all the TV settings for the television.
Software Upgrade: From time to time we may release new firmware to improve the running
of the television (available to download). This menu lets you upgrade that software onto the
television. Further details of how to do this will be issued with the firmware. Contact the
helpline or refer to the ‘product support’ section of the website.
Load Default Database: Import the default satellites and channel, so that the user can watch
programs directly.
17
Multimedia Operation
Basic Operation
1). Press the INPUT button on the remote control to display the input source menu, select Media
source by the /
buttons, and press OK button to enter the Multimedia menu as shown below.
2). Insert USB device, and select the Media mode form Photo, Music, Movie and eBook, then you will
find the name of the device display on the screen as shown below.
Hints for operation
3). Press
/
button to select the USB device and press OK button to enter the file list as shown below.
Return to
device list
Preview
File list
Informations
Hints
Press
/
buttons to move (press OK button to select the file or unfold the folder);
Press RED button to delete the file; Press GREEN button to sign or cancel all the files to playlist;
Press OK button to sign or cancel the selected file to playlist.
Press
button to previous menu, Press EXIT button to select the file view type list( ) or thurnbnail(
Press Exit again to veturn to the root MENU.
Then press
button to program the files (be signed) you select or the files in the fold you select.
Press
button to stop and exit the full screen program, please notes the hints on the bottom.
18
).
Multimedia Operation
1. Photo
Play the photo
Press / button to select the option on the table, and press OK button to change.
Note: You could press OK button to display the option table when it disappears.
Play/Pause the photo playing.
Stop and exit the full screen program.
Play the previous or next file directly.
Ratate the picture(0, 90, 180, 270).
Zoom in/out the picture, you could move the picture by Cursor left/right/up/down button in Zoom mode.
Display the information of the current file.
Display the photo setup menu, and select the Repeat mode, Background Music, Slide Time, Effect.
Display the playing list.
2. Music
Play the music
Press / button to select the option on the table, and press OK button to change.
Play/Pause the music playing.
Stop and exit the music playing.
Play fast backword or forword.
Play the previous or next file directly.
ALL Select the repeat mode for playing music.
Switch the window between “Information” and “Playlist”.
Switch off the screen displaying (BLUE button as quick button), and it will be turned on by
exepet power button)..
19
Multimedia Operation
3. Movie
Play the movie
Press / button to select the option on the table, and press OK button to change.
Note: You could press OK button to display the option table when it disappears.
AB
Play/Pause the movie playing.
Stop and exit the full screen program.
Play fast backword or forword.
Play the movie in slow mode.
Play the movie in step mode.
Set the A-B repeat playing mode.
Play the previous or next file directly.
Display the playing list.
Display the information of the current file.
Display the movie setup menu, and setup the Program, Subtitle, Audio, Repeat mode.
Goto mode, Input the time and start playing directly.
4. eBook
Play the text
Turn to previous/next page of the text.
RED button: Add or delete the bookmark.
GREEN button: Goto the appoint page.
YELLOW button: Display the bookmark list.
BLUE button: Display the playlist.
20
Recording Operation
PVR settings
Press the MENU button select Feature-PVR/Timeshift menu, press OK button to enter the menu as below.
1). Record File Format
Select Record File Format mode from TS and PS for storing in the USB device.
2). Partition Select
USB device informations
Format: Press RED button to format the selected USB device.
Set Default Partition: Press GREEN button to set the focus partition as the
default partition .The recorders are stored in the default partition. It need to
be reset if the default partition is full in recording progress.
3). Timeshift Buffer
Set Timeshift Buffer mode: auto, 30Mins, 1hr, 2hr.
4). Timer
Enter the Timer menu to setup the timer recording settings.
Press yellow button to add.
Recorder: Turn on/off the recorder function.
Type: Select the type of the program you want to recording.
Channel: Select the channel you want to recording.
Start Time: Setup the start time for recording the program.
Duration: Setup the duration time for recording.
Date: Select the date for recording.
Mode: Select the mode for recording.
21
Recording Operation
5). Record List
Display the Record list menu.
Delete: Press RED button to delete the selected record plan.
6). Recorder Start
Press OK button to start recording, as the function of the REC button on the remote control.
EPG and Timer Record
Press EPG button on the remote control to display the EPG menu.
EPG mode: Press RED button to change the EPG display mode.
Daily mode: shows the information of the programs to be broadcasted in daily mode.
Weekly mode: shows the information of the programs to be broadcasted in weekly mode.
Reminder: Press GREEN button once to remind the program for watching, and press GREEN button again
to remind the program for recording. You could check it in Timer menu, and the TV will record the
program according to your settings automatically.
Previous/Next Day: Press YELLOW/BLUE button to display the programs on previous or next day.
22
Recording Operation
Recording
Press REC button on the remote control to start recording in DTV mode. Press
appears. Select “OK” item, and press OK to exit recording
a message window
Note:
a. Please make sure the USB device is on the TV.
b. Please mke sure the speed and free space of the USB is enough.
c. Press Recording list button to display the Recorder list, and you can play the program you selected.
d. You can also play the Recorded program in Multimedia mode.
Timeshift
Press
Press
button on the remote control to start timeshift in DTV mode.
to stop timeshift.
Note:
a. Please make sure the USB device is on the TV.
b. Please make sure the speed and free space of the USB is enough.
c. Press
button to pause the program you are watching, and the timeshift will start.
d. Timeshift time menu on the corner shows the time between the current picture and the
living broadcasting picture;
e. During the recoding progress, if the signal is missing, the recording process will take a pause until the
signal is stable again.
23
DVD Operation
Press the Power button on the TV or the remote control, then press the INPUT button to select DVD mode.
If there is no disc in the DVD player the screen will show "NO DISC".
Insert Disc according to picture next to disc slot.
Do not touch the playing surface.
Hold the disc around the outside with your fingers and place the disc into the slot. The player will
automatically draw the disc into the player.
To "Eject" the disc, press the EJECT button on the TV or the " " button on the remote control.
Audio
4:3 Pan Scan
4:3 Letter Box
Wide
4:3 Pan Scan
4:3 Letter Box
Wide
24
DVD Operation
25
DVD Operation
26
DVD Operation
Spdif Setup
27
DVD Operation
or NO disc
28
DVD Operation
29
DVD Operation
30
DVD Operation
PAL
31
Simple Troubleshooting
If the display fails or performance dramatically deteriorates check the Display in accordance
with the following instructions.Remember to check the peripherals topinpiont the source of the
failure.
If the display still fails to perform as expected,connect your helpline for assistance.
No power
- Check all connections to the TV.
- Press either the power button or the Standby button on the Remote control.
No picture or sound
- Ensure that the TV is plugged in and the power is on.
- Ensure that the aerial is connected.
- Try a different program.
Poor picture quality
- Check the aerial connections.
- Check that the channel is tuned in properly.
- Adjust the picture settings:brightness,color,sharpness,contrast,hue.
- Make sure that the TV is not located close to electrical appliances that may emit radio
frequency interference.
No colour
- Adjust the color setting.
- Check that the programme is broadcast in color.
- Check that the channel is tuned properly.
TV does not respond to remote control
- Check that there are no obstructions between the remote control and the unit.
- Check that the remote control is within range of the unit.
- Check that the batteries in the remote control and not weak or exhausted.
This TV is for household use and registered as harmless on electromagnetic waves.
Therefor,you can use it in every location as well as residential areas.
32
Download PDF
Similar pages