For Intermediate & Advanced Fliers.
SAFETY PRECAUTIONS
This radio control model is not a toy!
Fist-time builders should seek advice from people having building
Experience in order to assemble the model correctly and to produce
Its performance to full extent.
Assemble this kit only in places out of children’s reach!
Take enough safety precautions prior to operating this model.
You are responsible for this model’s assembly and safe operation!
Always keep this instruction manual ready at hand for quick
reference, even after completing the assembly.
Notice:
**This manual included Specification, Parts list in paper and CD full instruction manual.**
Before you read the CD. Please install Acrobat Reader. First.
“Acrobat Reader” logo are trademarks of Adobe Systems Incorporated
01
01
Find a pair of tail control wire as show.
Before you install this control wire please clean it with
alcohol.
02
Install tail control wire as show.
03
Two control wire after install.
04
Trim off cover film and Install control horn and glue it
with Epoxy or mid CA.
05
Made sure the contort horn was vertical when the tail
surface was install.
06
Drill some hole under the tail surface angle block to
made the tail surface glue more secure.
07
Drill some hole under the tail surface angle block to
made the tail surface glue more secure.
08
03
Drill some hole on top of the tail surface to made the
tail surface glue more secure.
09
Install the both tail surface at the tail and fix them with
Epoxy.
10
Before you install the tail surface you must install the
“ Z” push rod with control horn first.
11
Made sure the control surface was free before you
glue the control horn.
12
Cut off Servo bay center parts very carefully.
13
05
Install the mini servo the servo bay as show in both
side.
14
Hook on receiver and tail control servo and turn on the
radio then neutral both tail servo and fix the control
wire as show.
15
Place a 3-4cm long sticker Hook on tip end of servo
tray for receiver mounting.
16
06
Place stick Loop on the under side of receiver.
17
Mount the receiver at the end of the servo tray as
Before you install the servo tray inside the Fuse. You
need to hookup the tail control servo and three-6in
servo extension wire for Ailerons and throttle control.
18
Place double stick Velcro at font end of battery tray
for battery mounting as show.
19
07
Install the battery tray in to holding ply.
20
Fix the battery tray with a 2X12 TP. Screw as show.
21
Place the ESC. understand the battery tray.
22
08
Mount the battery on the battery tray in vertical and
check the battery will not hit any servo arm.
23
You can let the Antenna out from air exit.
We don’t suggest you made the Antenna out from
bottom because it is easy to cut the antenna when you
landing.
24
If you choice deluxe kit that with power set together.
The motor, spinner and prop. Already install before
ship.
If you choice other motor please follow you motor
mount bolt pattern to open nose.
25
Check the center point before you drill any hole for
the motor install. You may need to use power tool to
make big hole for spinner and motor ball bearing.
26
After you drill four holes for motor mount bolt you
may need use bigger drill bit to made the hole out side
a bit bigger. Because you need use countersink screw
for motor mounting.
27
11
Use power tool to open the cooling air intake as show.
28
Use power tool to open the cooling air exit as show.
29
Fix motor with four-countersink screw as show.
30
Check the center when you mount the motor.
31
the Alum. Spinner and carbon prop. That supply with
deluxe kit. If you choice an ARF. Kit .please use a
40mm diameter spinner.
32
Please check tighten spinner lock screw before your
hookup the power.
33
the ultra cooling 70AMP. ESC.
The motor plug was already installed if you choice the
ESC. Supply with deluxe kit.
You just need to install battery plug only.
If you choice other motor and ESC. Please 4.5mm
good quality plug that can be handle 100AMP. only.
34
Trim off covering from wing bolthole at both wings
penal as show.
35
13
Drill a 2mm hole at root of both sides as show
Then install 2mm wire at one side.
Notice you must make sure the wire anti roll pin
match both side wings penal.
36
Drill a 2mm hole at root of both sides of fuse.
37
Join wing penal together with solid carbon wing join
that supply with the kit.
38
Mount both wings penal on to the Fus. With 3mm
wing bolt.
39
14
Trim of covering from Ailerons servo bay.
40
Use a thin wire to lead out the servo extend wire as
show.
41
42
Hack up servo lead and secure plug then put all wire
in side wing panel.
43
15
Install plastic servo tray to servo bay.
Fix servo tray to the servo bay with CA. glue or
epoxy.
44
Install control push rob as show.
45
After you final adjust all control push rod,
servo hatch with TP screw as show.
46
fix the
16
Check max low Ailerons and servo control horn as
show.
Notice: All control throw information you can find in
SEP. sheet.
47
Adjust Ailerons max low throw with gage as show.
Notice: All control throw information you can find in
SEP. sheet.
48
Check Ailerons center and servo control as show.
49
Check Ailerons max up and servo control horn as
show.
Notice: All control throw information you can find in
SEP. sheet.
50
17
Adjust Ailerons max up throw with gage as show.
Notice: All control throw information you can find in
SEP. sheet.
65
Install CG. Check tray as show.
Please find the ply parts
The recommend C.G. point was 75mm from LE. At
Root but you can adjust differ C.G. point for your own
fly style. From 8mm forward to 5mm backward from
this point.
66
Use CG. Checking tray to check and adjust correct CG.
67
Use battery to adjust CG. Point is it necessarily.
68
Find the carbon canopy parts.
69
Install the lock wire inside the tube then glue it
together with Epoxy.
SPECIFICATION
Description
WING SPAN
WING AREA
FUS. LENGTH
TOTAL LENGTH
CODE:G007
2240mm
36.85sq dm.
1052.5mm
1086mm
RUDDER AREA
STAB.AREA
ELEVATOR AREA
ROOT AIRFOIL
TIP AIRFOIL
AILERON
Elevator
Rudder
5.64dm2
2
1.42dm
11.4% Symmetrical
ITEM:
Description
Suggest:ENGINES CLASS
Suggest:Motor/ESC
RTF. WEIGHT GP.Setup
RTF. WEIGHT EP.Setup
CENTER OF GRAVITY
WING INCIDENCE
WING DIHEDRAL
STAB. INCIDENCE
RIGHT THRUST
DOWN THRUST
ENGINE OFFSET
X 40 L B.L,motor
1.7KG-2.0KG
75MM at root
1.5 °
2.4 °
0°
3°
7 °
CONTRL THROWS
LOW RATE
UP
DOWN
30Degree 30Degree
HIGH RATE
Aieron breaking
UP
DOWN UP
DOWN
20Degree
20Degree 35Degree
30Degree 30Degree
Left
Right
30degree 30Degree
25Degree
Left
35degree
25Degree adjust in fly
Right
Left
35Degree
Right
Wing
hardware
pack
Elevator
hardware
pack
Description
CARBON WING JOIN
WIRE ANTI ROLL PIN
WING BOLT
SERVO BAY & FAIRING
WING BOLT
WING BOLT Washer
Aileron push rod
clevis
Aileron contorl horn
servo hactch mount screw
Tail plane contorl push rod
contorl wire Adjuster
Canopy
Hardware
pack
size
QUT′Y REMARK
¢10x268
1PC
¢2x25mm
1PC
¢5x25
2PCS
1pair
¢3X10
2PCS
3X8
2PCS
¢1.7x50
2PCS
¢2
2PCS
1.5mm
2PCS
¢2x10
8PCS
¢1x915
¢2
2PCS
2PCS
1.5mmGRP
2PCS
ply battery tray parts
battery tray mount screw
3mm
2X12
1set
1PC
canopy lock wire
Carbon canopy
GRP. Fuse.
duoble layer Obechi molded wing
balsa tail plane
¢1.7x175
1PC
1PC
1PC
1pair
1pair
Tail plane contorl horn
Fuselage
hardware
pack
code
Date: 15/01/2011
Deluxe kit contents
X 40 L B.L,motor
40mm Alum. Spinner
14 X 9 carbon folding prop.
1.5mm
1pc
1pc
1set
Download PDF
Similar pages