RTG-920VK Manual.qxd

TABLE OF CONTENTS
SPECIFICATIONS……………………………………….. Page 2
KNOW YOUR PRODUCT………………………………. Page 2
INTRODUCTION………………………………………..Page 3
ELECTRICAL SAFETY…………………………………… Page 3
GENERAL SAFETY INSTRUCTIONS…………………. Page 4
ADDITIONAL SAFETY INSTRUCTIONS FOR
THE GLUE GUN………………………………………… Page 6
OPERATION………………………………………………Page 7
MAINTENANCE………………………………………… Page 8
SPARE PARTS…………………………………………… Page 9
DESCRIPTION OF SYMBOLS…………………………. Page 9
PACK CONTENTS……………………………………….Page 10
WARRANTY……………………………………………… Page 11
1
SPECIFICATIONS MODEL NO. GGC-015
Motor:
Input:
Flow rate of glue:
Diameter of glue stick:
Length of glue stick:
Maximum temperature range:
Weight (tool only):
15W
220-240V~ 50Hz
14-16g/min
11.2mm
100mm
170°-190°C
0.45kgs
KNOW YOUR PRODUCT
3
2
4
5
6
1
7
1.
2.
3.
4.
Protective nozzle cover
Glue display
LED indicator lights
Ergonomic handle
8
5.
6.
7.
8.
Trigger flow control
Charging stand
Fold out metal stand
Power cord
2
INTRODUCTION
Congratulations on purchasing an Ozito Glue Gun. We aim
to provide quality tools at an affordable price.
We hope you will enjoy using this tool for many years. Your
Glue Gun GGC-015 has been designed for fastening various
materials such as fabric, wood, tiles, rubber, ceramics etc. It
is intended for DIY use only.
!
ELECTRICAL SAFETY
!
WARNING! When using mains-powered equipment, basic safety
precautions, including the following, should always be followed to reduce
risk of fire, electric shock, personal injury and material damage.
Read and understand the manual prior to operating this tool.
Save these instructions and other documents supplied with this tool for future reference.
The electric motor has been designed for 230V and 240V only. Always check that
the power supply corresponds to the voltage on the rating plate.
Note: The supply of 230V and 240V on Ozito tools are interchangeable for
Australia and New Zealand.
This tool is double insulated in accordance with 60335-1; therefore no earth
wire is required.
If the supply cord is damaged, it must be replaced by an electrician or a power tool
repairer in order to avoid a hazard.
If operating a power tool in a damp location is unavoidable use a residual current
device (RCD) protected supply
Use of an RCD reduces the risk of electric shock.
Note: Double insulation does not take the place of normal safety precautions when
operating this tool. The insulation system is for added protection against injury
resulting from a possible electrical insulation failure within the tool.
Using an Extension Lead
Always use an approved extension lead suitable for the power input of this tool.
Before use, inspect the extension lead for signs of damage, wear and ageing.
Replace the extension lead if damaged or defective. When using an extension lead
on a reel, always unwind the lead completely. Use of an extension lead not suitable
for the power input of the tool or which is damaged or defective may result in a
risk of fire and electric shock.
3
!
GENERAL SAFETY INSTRUCTIONS
!
WARNING! Read all instructions. Failure to follow all instructions listed
belowmay result in electric shock, fire and/or serious injury. The term "power
tool" in all of the warnings listed below refers to your mains-operated
(corded) power tool or battery-operated (cordless) power tool.
Save these instructions
1) Work area
a) Keep work area clean and well lit. Cluttered and dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions
can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded) power tools. Unmodified
plugs and matching outlets will reduce risk of electric shock
b) Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric shock if
your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging
the power tool. Keep cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when operating
a power tool. Do not use a power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention while operating power
tools may result in serious personal injury.
b) Use safety equipment. Always wear eye protection. Safety equipment such as
dust mask, non-skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c) Avoid accidental starting. Ensure the switch is in the off-position before
plugging in. Carrying power tools with your finger on the switch or plugging in
power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of the power tool may result in
personal injury.
4
! GENERAL SAFETY RULES (cont.)
e) Do not overreach. Keep proper footing and balance at all times. This enables
better control of the power tool in unexpected situations.
f)
Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of these
devices can reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the rate
for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and must
be repaired.
c) Disconnect the plug from the power supply and/or the battery pack from
the power tool before making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate
the power tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tools
operation. If damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
f)
Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these
instructions and in the manner intended for the particular type of power
tool, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended
could result in a hazardous situation.
5) Service
a) Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power tool
is maintained.
b) If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
5
! ADDITIONAL SAFETY INSTRUCTIONS FOR GLUE GUNS
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Recommendations for the use of a residual current device with a rated residual
current of 30mA or less.
Using an Extension Lead
Ensure the area is well ventilated.
Heating some materials can cause fumes.
Always use an approved extension lead suitable for the power input of this tool. Before
use, inspect the extension lead for signs of damage, wear and ageing. Replace the
extension lead if damaged or defective.
When using an extension lead on a reel, always unwind the lead completely. Use of an
extension lead not suitable for the power input of the tool or which is damaged or
defective may result in a risk of fire and electric shock.
It is recommended that the extension lead is a maximum of 25m in length. Do Not use
multiple extension leads.
Safety Tips
-
Do not touch hot glue.
-
Do not remove the glue from skin in the event of accidental contact. Immediately
run cold water over and seek medical advice.
-
Do not leave glue gun unattended while in use or directly after use.
-
Do not touch the nozzle end of the gun while in use or directly after use.
-
Do not inhale vapours generated while in use.
-
Do not attempt to feed any other materials through the glue gun, eg. crayons,
sealants, candles etc.
The appliance is not intended for use by young children or infirm persons unless they
have been adequately supervised by a responsible person to ensure that they can use
the appliance safety.
Young children should be supervised to ensure that they do not play with the appliance.
6
OPERATION
This glue gun has been designed so that it can be used as either a corded or cord
free unit.
The glue gun can be used continuously when
connected via the cord to a 240V power source (Fig.1).
Alternatively, placing the glue gun in the stand to heat
the element between 5-8 minutes, will allow you to use
the glue gun cord free for up to 5 minutes.
Fig. 1
Loading the Glue Stick
1. Insert the glue stick into the entry hole of the glue gun and squeeze the trigger
flow control (5) to further load the glue stick into the glue gun.
Note: If there is no glue released from the nozzle, you
may need to insert another glue stick.
2. The glue may stop flowing when there is
approximately a 1/4 left of the glue stick sitting out
of the entry hole (Fig. 2).
3. Insert another glue stick and push the existing one
in. Then push the trigger flow control (5).
Fig. 2
Heating the Glue Stick
1. Ensure the glue gun is sitting in the charging stand (6).
2. Connect the power cord to the glue gun (Fig. 3).
Then plug the cord to the mains power outlet. The
LED indicator lights (3) will turn red once it is
connected.
3. Allow the glue gun to heat up on the charging
stand (6) for 5 - 8 minutes before use.
Fig. 3
7
OPERATION (cont.)
Trigger Flow Control
The flow rate of the glue is dependent on how much pressure is applied to the trigger
flow control (5).
1. Squeeze the trigger flow control (5) to release the glue
(Fig. 4). Press surfaces to be glued together within 15
seconds for a strong bond.
Tip: Ensure the glue sticks are heated fully to allow an
even flow of glue.
2. To stop the flow of glue from the gun, release the
trigger flow control (6).
Fig. 4
3. Disconnect the glue gun or the charging stand (6) from the mains power outlet to
stop heating glue gun. The LED indicator light (3) will go off when power has been
switched off.
Caution: The protective nozzle (1) will remain hot for a few minutes. Do not store the
glue gun directly after use. Allow the nozzle to cool and the glue to solidify.
Fold Out Stand
The glue gun can be used upright, giving you extra stability when dealing with finer
applications.
1. Fold out the metal stand (7) and rest the glue gun
upright on a flat surface (Fig. 5).
Fig. 5
!
WARNING! The glue gun nozzle and heated glue become hot while in use.
In the event of accidental skin contact with the hot glue run under cold water
immediately. This glue gun must be placed on it’s stand when not in use.
MAINTENANCE
•
If the housing of the glue gun requires cleaning do not use solvents but a moist
soft cloth only. Never immerse any part of the glue gun into liquid.
Note: Ozito Industries will not be responsible for any damage or injuries caused by the
repair of the glue gun by an unauthorised person or by mishandling of the glue gun.
8
SPART PARTS
Limited spare parts are available subject to availability. Please contact your local
Bunnings Special Orders Desk to order the required spare parts.
Most common spare parts listed below
Spare Part
Part No.
Power Cord
SPGGC015-12
Base
SPGGC015-18
Socket
SPGGC015-24
DESCRIPTION OF SYMBOLS
V
Volts
Hz
Hertz
~
Alternating current
W
Watts
/min
Revolutions or
reciprocation per minute
no
No load speed
Diameter
ºC
Temperature
ø
Double insulated
9
Regulator compliance mark
CARING FOR THE ENVIRONMENT
Petrol tools that are no longer usable should not be disposed
of with household waste but in an environmentally friendly
way. Please recycle where facilities exist. Check with your
local council authority for recycling advice.
Recycling packaging reduces the need for landfill and raw
materials. Reuse of recycled material decreases pollution in the
environment. Please recycle packaging where facilities exist.
Check with your local council authority for recycling advice.
PACK CONTENTS
1 x Cordless Glue Gun GGC-015
1 x Charging stand
4 x Glue sticks
1 x Instruction manual
OZITO INDUSTRIES PTY LTD
AUSTRALIA (Head Office)
1 - 23 Letcon Drive, Bangholme, Victoria, Australia 3175
Telephone: 1800 069 486
Facsimile: +61 3 9238 5588
Website: www.ozito.com.au
Email: enquiries@ozito.com.au
10
WARRANTY
YOUR WARRANTY FORM SHOULD BE RETAINED BY YOU AT ALL TIMES. IN ORDER
TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO
YOUR NEAREST BUNNINGS WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT.
PRIOR TO RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR
CUSTOMER SERVICE HELPLINE:
`Australia 1800 069 486
New Zealand 0508 069 486
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
The benefits provided under this warranty are in addition to other rights and remedies which
are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You are entitled to a
replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if
the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Generally you will be responsible for all costs associated with a claim under this warranty,
however, where you have suffered any additional direct loss as a result of a defective product
you may be able to claim such expenses by contacting our customer service helpline above.
1 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 12 months from the original date of purchase
and is intended for DIY (Do It Yourself) use only. If a product is defective it will be replaced in
accordance with the terms of this warranty. Warranty excludes consumable parts, for example:
glue sticks.
WARNING
The following actions will result in the warranty being void.
•
•
•
•
•
Professional, Industrial or high frequency use.
If the tool has been operated on a supply voltage other than that specified on the tool.
If the tool shows signs of damage or defects caused by or resulting from abuse, accidents
or alterations.
Failure to perform maintenance as set out within the instruction manual.
If the tool is disassembled or tampered with in any way.
OZITO
Australia/New Zealand (Head Office)
1-23 Letcon Drive, Bangholme, Victoria, Australia 3175
OW14
Download PDF
Similar pages