ENGLISH (Original instructions)
INSTRUCTION MANUAL
Cordless 4 Mode Impact Driver
DTP131
DTP141
012232
IMPORTANT: Read Before Using.
1
ENGLISH (Original instructions)
SPECIFICATIONS
Model
Fastening
Capacities
Impact driver
mode
DTP131
DTP141
Machine screw
4 mm - 8 mm
Standard bolt
5 mm - 14 mm
High tensile bolt
5 mm - 12 mm
No load speed (min-1) (Soft / Medium / Hard)
0 - 1,400 / 0 - 2,200 / 0 - 2,800
Impacts per minute (Soft / Medium / Hard)
0 - 1,300 / 0 - 2,200 / 0 - 2,700
0 - 1,200 / 0 - 2,400 / 0 - 3,200
Low (1) / High (2)
No load speed (min-1)
Hammer drill mode
0 - 700 / 0 - 2,800
Blows per minute (min-1)
0 - 700 / 0 - 2,700
0 - 8,400 / 0 - 32,400
Drilling Capacities / Concrete
8 mm
Steel
Drill mode
Drilling Capacities
10 mm / 6.5 mm
Wood
21 mm / 12 mm
No load speed (min-1)
0 - 700 / 0 - 2,800
Machine screw
Screwdriver mode
Fastening
Capacities
0 - 700 / 0 - 2,700
3.5 mm - 6 mm / 4 mm - 6 mm
Self drilling screw
4 mm, 5 mm / 4 mm (Thickness 3.2 mm max.)
No load speed
(min-1)
0 - 300 / 0 - 1,100 (depends on torque setting)
0 - 600 / 0 - 2,300 (P mode)
Battery cartridge
BL1415 /
BL1415N
BL1430 / BL1430B /
BL1440 / BL1450 /
BL1460B
BL1815 / BL1815N /
BL1820 / BL1820B
BL1830 / BL1830B /
BL1840 / BL1840B /
BL1850 / BL1850B /
BL1860B
Net weight
1.5 kg
1.7 kg
1.5 kg
1.8 kg
Rated voltage
D.C. 14.4 V
D.C. 18 V
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003
END004-6
ENE064-1
Intended use
The tool is intended for impact screw driving in wood and
for impact drilling in brick, concrete and stone as well as
for drilling and screw driving without impact in wood,
metal, ceramic and plastic.
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
Read instruction manual.
ENG905-1
Cd
Ni-MH
Li-ion
Only for EU countries
Do not dispose of electric equipment or
battery pack together with household
waste material!
In observance of the European
Directives, on Waste Electric and
Electronic Equipment and Batteries and
Accumulators and Waste Batteries and
Accumulators and their implementation
in accordance with national laws,
electric equipment and batteries and
battery pack(s) that have reached the
end of their life must be collected
separately and returned to an
environmentally compatible recycling
facility.
Noise
The typical A-weighted noise level determined according
to EN60745:
Model DTP131
Sound pressure level (LpA) : 85 dB (A)
Sound power level (LWA) : 96 dB (A)
Uncertainty (K) : 3 dB (A)
Model DTP141
Sound pressure level (LpA) : 85 dB (A)
Sound power level (LWA) : 96 dB (A)
Uncertainty (K) : 3 dB (A)
Wear ear protection
2
ENH101-18
For European countries only
ENG900-1
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
EC Declaration of Conformity
Makita declares that the following Machine(s):
Designation of Machine:
Cordless 4 Mode Impact Driver
Model No./ Type: DTP131, DTP141
Conforms to the following European Directives:
2006/42/EC
They are manufactured in accordance with the following
standard or standardized documents:
EN60745
The technical file in accordance with 2006/42/EC is
available from:
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
Model DTP131
Work mode: impact drilling into concrete
Vibration emission (ah,ID) : 13 m/s2
Uncertainty (K) : 1.5 m/s2
Work mode : impact tightening of fasteners of the
maximum capacity of the tool
Vibration emission (ah) : 8.5 m/s2
Uncertainty (K) : 2 m/s2
Work mode: drilling into metal
Vibration emission (ah,D) : 2.5 m/s2 or less
Uncertainty (K) : 1.5 m/s2
29.5.2015
Model DTP141
Work mode: impact drilling into concrete
Vibration emission (ah,ID) : 13 m/s2
Uncertainty (K) : 1.5 m/s2
000331
Yasushi Fukaya
Director
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
Work mode : impact tightening of fasteners of the
maximum capacity of the tool
Vibration emission (ah) : 10.5 m/s2
Uncertainty (K) : 1.5 m/s2
GEA006-2
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious injury.
Work mode: drilling into metal
Vibration emission (ah,D) : 2.5 m/s2 or less
Uncertainty (K) : 1.5 m/s2
ENG901-1
•
•
•
•
Save all warnings and
instructions for future reference.
The declared vibration emission value has been
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
The declared vibration emission value may also be
used in a preliminary assessment of exposure.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1.
Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2.
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
3.
Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
Electrical safety
4.
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
WARNING:
The vibration emission during actual use of the
power tool can differ from the declared emission
value depending on the ways in which the tool is
used.
Be sure to identify safety measures to protect the
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
3
5.
Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
6.
Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
7.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
8.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
9.
If operating a power tool in a damp location is
unavoidable, use a ground fault circuit
interrupter (GFCI) protected supply. Use of an
GFCI reduces the risk of electric shock.
Personal safety
10. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
11. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
12. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools
that have the switch on invites accidents.
13. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
14. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
15. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving
parts.
16. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
Power tool use and care
17. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
18. Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
19. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
20. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
21. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
22. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
23. Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.
Battery tool use and care
24. Recharge only with the charger specified by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of fire
when used with another battery pack.
25. Use power tools only with specifically
designated battery packs. Use of any other
battery packs may create a risk of injury and fire.
26. When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another. Shorting the battery
terminals together may cause burns or a fire.
27. Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water. If
liquid contacts eyes, additionally seek medical
help. Liquid ejected from the battery may cause
irritation or burns.
4
ENC007-10
Service
28. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
29. Follow instruction for lubricating and
changing accessories.
30. Keep handles dry, clean and free from oil and
grease.
IMPORTANT SAFETY
INSTRUCTIONS
FOR BATTERY CARTRIDGE
Before using battery cartridge, read all instructions
and cautionary markings on (1) battery charger, (2)
battery, and (3) product using battery.
2.
Do not disassemble battery cartridge.
3.
If operating time has become excessively shorter,
stop operating immediately. It may result in a risk of
overheating, possible burns and even an explosion.
4.
If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5.
Do not short the battery cartridge:
(1) Do not touch the terminals with any
conductive material.
(2) Avoid storing battery cartridge in a
container with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water or rain.
A battery short can cause a large current flow,
overheating, possible burns and even a breakdown.
6.
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 C (122 F).
7.
Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.
8.
Be careful not to drop or strike battery.
9.
Do not use a damaged battery.
10. Follow your local regulations relating to
disposal of battery.
1.
GEB078-2
CORDLESS 4 MODE IMPACT
DRIVER SAFETY WARNINGS
1.
Wear ear protectors when impact drilling.
Exposure to noise can cause hearing loss.
2.
Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.
3.
Hold power tool by insulated gripping
surfaces, when performing an operation where
the fastener may contact hidden wiring.
Fasteners contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
4. Hold power tool by insulated gripping surfaces,
when performing an operation where the
cutting accessory may contact hidden wiring.
Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
5.
Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
6.
Hold the tool firmly.
7.
Keep hands away from rotating parts.
8.
Do not leave the tool running. Operate the tool
only when hand-held.
9.
Do not touch the bit or the workpiece
immediately after operation; they may be
extremely hot and could burn your skin.
10. Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation and
skin contact. Follow material supplier safety data.
SAVE THESE INSTRUCTIONS.
CAUTION: Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that
have been altered, may result in the battery bursting
causing fires, personal injury and damage. It will also
void the Makita warranty for the Makita tool and charger.
Tips for maintaining maximum battery life
SAVE THESE INSTRUCTIONS.
1.
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this
instruction manual may cause serious personal
injury.
2.
3.
4.
5
Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the battery
cartridge when you notice less tool power.
Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
Charge the battery cartridge with room
temperature at 10 C - 40 C (50 F - 104 F). Let a
hot battery cartridge cool down before charging it.
Charge the battery cartridge if you do not use
it for a long period (more than six months).
Lithium-ion batteries with a star marking are equipped
with a protection system. This system automatically cuts
off power to the tool to extend battery life.
The tool will automatically stop during operation if the tool
and/or battery are placed under one of the following conditions:
•
Overloaded:
The tool is operated in a manner that causes
it to draw an abnormally high current.
In this situation, release the trigger switch on
the tool and stop the application that caused
the tool to become overloaded. Then pull the
trigger switch again to restart.
If the tool does not start, the battery is
overheated. In this situation, let the battery
cool before pulling the trigger switch again.
•
Low battery voltage:
The remaining battery capacity is too low and
the tool will not operate. In this situation,
remove and recharge the battery.
FUNCTIONAL DESCRIPTION
•
CAUTION:
Always be sure that the tool is switched off and the
battery cartridge is removed before adjusting or
checking function on the tool.
Installing or removing battery cartridge
1. Red indicator
2. Button
3. Battery cartridge
1
2
3
012233
CAUTION:
Always switch off the tool before installing or
removing of the battery cartridge.
•
Hold the tool and the battery cartridge firmly
when installing or removing battery cartridge.
Failure to hold the tool and the battery cartridge
firmly may cause them to slip off your hands and
result in damage to the tool and battery cartridge
and a personal injury.
To remove the battery cartridge, slide it from the tool
while sliding the button on the front of the cartridge.
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip it
into place. Insert it all the way until it locks in place with a
little click. If you can see the red indicator on the upper
side of the button, it is not locked completely.
Indicating the remaining battery capacity
•
•
•
(Only for battery cartridges with "B" at the end of the
model number.)
1. Indicator lamps
2. CHECK button
1
2
015659
Press the check button on the battery cartridge to
indicate the remaining battery capacity. The indicator
lamps light up for few seconds.
CAUTION:
Always install the battery cartridge fully until the red
indicator cannot be seen. If not, it may accidentally fall out
of the tool, causing injury to you or someone around you.
Do not install the battery cartridge forcibly. If the cartridge
does not slide in easily, it is not being inserted correctly.
Indicator lamps
Remaining
capacity
Lighted
Off
Blinking
75% to 100%
Battery protection system
(Lithium-ion battery with star marking)
50% to 75%
25% to 50%
1
1. Star marking
0% to 25%
Charge the
battery.
The battery
may have
malfunctioned.
012128
015658
6
With the lamp button in the ON status, pull the switch
trigger to turn on the lamp. To turn off, release it and the
lamp goes out approximately 10 seconds after releasing.
With the lamp button in the OFF status, even if the trigger
is pulled, the lamp will not light on.
NOTE:
•
Depending on the conditions of use and the
ambient temperature, the indication may differ
slightly from the actual capacity.
Switch action
NOTE:
•
To make sure the status of lamp, pull the trigger.
When the lamp lights up by pulling the switch
trigger, the lamp switch is in the ON status. When
the lamp does not come on, the lamp switch is in
the OFF status.
•
During the operation of switch trigger, the lamp
status cannot be changed.
•
For approximately 10 seconds after releasing the
switch trigger, the lamp status can be switched.
1. Switch trigger
1
012237
CAUTION:
Before installing the battery cartridge into the tool, always
check to see that the switch trigger actuates properly and
returns to the "OFF" position when released.
To start the tool, simply pull the switch trigger. The tool
speed is increased by increasing pressure on the switch
trigger. Release the switch trigger to stop.
Reversing switch action
•
1. Reversing switch
lever
A
NOTE:
•
The tool will stop three minutes after pulling the
switch trigger.
012238
This tool has a reversing switch to change the direction of
rotation. Depress the reversing switch lever from the A
side for clockwise rotation or from the B side for
counterclockwise rotation.
When the reversing switch lever is in the neutral position,
the switch trigger cannot be pulled.
Lighting up the front lamp
•
B
1
CAUTION:
Do not look in the lamp or see the source of lamp
directly.
1. Lamp
•
•
1
•
012231
1
CAUTION:
Always check the direction of rotation before
operation.
Use the reversing switch only after the tool comes
to a complete stop. Changing the direction of
rotation before the tool stops may damage the tool.
When not operating the tool, always set the
reversing switch lever to the neutral position.
Speed change
1. LED display
2. Lamp button
1
2
012249
Every time the lamp button
on the LED display is
pressed, the lamp status is alternatively changed from
the ON to the OFF and from the OFF to the ON.
012240
7
1. Speed change
lever
NOTICE:
•
Always set the speed change lever fully to the
correct position. If you operate the tool with the
speed change lever positioned halfway between the
"1" side and "2" side, the tool may be damaged.
•
Do not use the speed change lever while the tool is
running. The tool may be damaged.
•
Do not force the lever to "1" side with impact driver
mode. The tool may be damaged.
To change the speed, first switch off the tool and then
slide the speed change lever to the "2" side for high
speed or "1" side for low speed. Be sure that the speed
change lever is set to the correct position before
operation. Use the right speed for your job.
When turning the action mode changing ring to impact
driver mode, set the speed change lever to the "2" side.
Changing the impact force
(impact driver mode " ")
1
2
5
3
Selecting the action mode
1
2
4
1. Mode mark
2. Action mode
changing ring
3. Arrow
1. Changed in three steps
2. Hard
3. Medium
4. Soft
5. Control button
3
012244
012239
This tool employs an action mode changing ring. Select
one of the 4 modes suitable for your work need by turning
this ring.
When driving wood screws or bolts, point the arrow at the
mark for impact driver mode. The impact force can be
adjusted on the LED display.
When drilling into concrete or tiles, point the arrow at the
mark for hammer drill mode.
When drilling into wood or metal, point the arrow at the
mark for drill mode.
When driving small wood screws or machine screws,
point the arrow at the
mark for screwdriver mode. The
fastening torque can be adjusted on the LED display.
•
•
•
CAUTION:
Always set the arrow correctly to either mode mark.
If you operate the tool with the action mode
changing ring positioned halfway between the
mode marks, the tool may be damaged.
When turning the action mode changing ring, make
sure that the tool stops. If the ring does not easily
move, pull the switch trigger slightly to rotate the
spindle and then move the ring.
In the hammer drill mode or drill mode, the blowing
force or torque is not adjustable. In those modes,
the number on the LED display will be off.
8
Impact force grade
displayed on panel
Maximum blows
Application
Work
DTP131
DTP141
3,200
(min -1)
3,200
(min -1)
Tightening when force
and speed are desired.
Tightening in underwork
material/ Tightening long
screws/ Tightening bolts.
2,400
(min -1)
2,400
(min -1)
Tightening when a good
finishing is needed.
Tightening in the finishing
board, plaster board.
1,200
(min -1)
1,200
(min -1)
Tightening when excessive
tightening need to be avoided Tightening sash screw/
because of potentially clogged Tightening small screws
female screw and broken or
such as M6.
damaged screw head.
Hard
Medium
Soft
014262
The impact force can be changed in three steps: hard,
medium and soft.
This allows a tightening suitable to the work.
Every time the button is pressed, the impact force
grade changes in three steps.
For approximately one minute after releasing the switch
trigger, the impact force can be changed.
With speed change lever at "1" side, fastening max.
5 mm screw.
Before an actual operation, drive a trial screw into your
material or a piece of duplicate material to determine
which torque level is required for a particular application.
First, try to fasten the screw at "1". Then increase the
number to continue fastening. Hold the tool firmly during
operation.
•
NOTE:
During the operation of switch trigger, the impact force
grade cannot be changed.
CAUTION:
Don't fasten the machine screw on P mode. It may twist
your wrist suddenly and result in personal injury.
Changing the torque setting
(screwdriver mode " ")
NOTE:
•
Make sure to check the number on LED display
before operation. If the number is not indicated,
contact your nearest Makita service center.
•
When the remaining battery capacity gets low in the
screwdriver mode, the light flashes a few times
when fastening the screw completely. In this case,
recharge the battery. If you keep operating, you
may not obtain the desired torque.
•
During pulling the switch trigger, the torque setting
cannot be changed.
•
For approximately one minute after releasing the
switch trigger, the torque setting can be changed. if
you want to change the torque setting after that,
pull the switch trigger again.
•
The number of torque setting does not mean
specific torque rate.
The fastening torque can be adjusted by pressing the
button
in screwdriver mode.
The numbers on the LED display shows torque setting.
The fastening torque is minimum at the number 1 and
maximum at the number 9. The indication "P" is a special
mode for fastening self drilling screws.
Every time the button is pressed, the torque setting
changes from 1 to 9 and P, and then returns to 1.
The torque setting changes fast by keeping pressing the
button.
P mode is suitable for fastening self drilling screws into
steel plates in the following conditions.
•
With speed change lever at "2" side, fastening max.
4 mm screw into total max. 3.2 mm steel plates.
9
ASSEMBLY
Empty signal for remaining
battery capacity
(Country specific)
CAUTION:
Always be sure that the tool is switched off and the
battery cartridge is removed before carrying out
any work on the tool.
•
1. Battery capacity
Installing or removing driver/drill/socket bit
1
012241
The remaining battery capacity will be signaled on the
LED display when pulling the switch trigger.
The remaining battery capacity is shown as the following
table.
LED indicator status
004521
Use only the driver/drill/socket bit shown in the figure. Do
not use any other driver/drill/socket bit.
For tool with shallow bit hole
Remaining battery capacity
About 50% or more
A=12 mm Use only these type of bit. Follow the
procedure (1).
B=9 mm
(Note) Bit-piece is not necessary.
006348
About 20% - 50%
For tool with deep bit hole
About less than 20%
A=17 mm To install these types of bits, follow
B=14 mm the procedure (1).
012273
NOTE:
•
When the LED display goes off, the tool is turned
off to save the battery power. To check the
remaining battery capacity, slightly pull the switch
trigger.
•
The LED display goes off approximately one
minute after releasing the switch trigger.
•
When the temperature of the tool gets high, the
light flashes once per second for one minute, and
then the LED display goes off. In this case, cool
down the tool before operation.
To install these types of bits, follow
A=12 mm the procedure (2).
B=9 mm
(Note) Bit-piece is necessary for
installing the bit.
011405
1.
To install the bit, pull the sleeve and insert the bit
into the sleeve as far as it will go. Then release the
sleeve to secure the bit.
1. Bit
2. Sleeve
1
2
012234
10
2.
To install the bit, insert the bit-piece and bit into the
sleeve as far as it will go. The bit-piece should be
inserted into the sleeve with its pointed end facing
in. Then release the sleeve to secure the bit.
OPERATION
1. Bit
2. Bit-piece
3. Sleeve
1
2
012242
3
012235
•
To remove the bit, pull the sleeve in the direction of the
arrow and pull the bit out firmly.
•
CAUTION:
Do not touch the drill bit shortly after operating as it
gets hot. Replace the drill bit after cooling it down.
NOTE:
•
If the bit is not inserted deep enough into the sleeve,
the sleeve will not return to its original position and
the bit will not be secured. In this case, try
re-inserting the bit according to the instructions
above.
•
After inserting the bit, make sure that it is firmly
secured. If it comes out, do not use it.
•
Impact driver mode "
"
CAUTION:
When changing the action mode to the impact
driver mode, always check that the tool impacts
by tightening wood screws. If the action mode is
not changed completely, the tool twists the
operator's hand resulting injury.
Screwdriving
Hold the tool firmly and place the point of the driver bit in
the screw head. Apply forward pressure to the tool to the
extent that the bit will not slip off the screw and turn the
tool on to start operation.
Tightening bolts
The proper fastening torque may differ depending upon
the kind or size of the screw/bolt, the material of the
workpiece to be fastened, etc. The relation between
fastening torque and fastening time is shown in the
figures.
•
Hook (Optional accessory)
1
CAUTION:
Always insert the battery cartridge all the way until it
locks in place with a little click. If you can see the
red indicator on the upper side of the button, it is not
locked completely. Install it fully until the red
indicator cannot be seen. If not, it may accidentally
fall out of the tool, causing injury to you or someone
around you.
If the tool is operated continuously until the battery
cartridge has discharged, allow the tool to rest for
15 minutes before proceeding with a fresh battery.
1. Groove
2. Hook
3. Screw
2
3
012236
CAUTION:
When installing the hook, tighten the screw firmly.
Failure to do so may cause the breakage of the tool
or personal injury.
The hook is convenient for temporarily hanging the tool.
This can be installed on either side of the tool.
To install the hook, insert it into a groove in the tool
housing on either side and then secure it with a screw. To
remove, loosen the screw and then take it out.
•
11
NOTE:
•
When the action mode is set to impact driver mode,
make sure that the tool impacts properly by
fastening a wood screw before operation. If the tool
does not work properly, contact your nearest Makita
service center.
•
Hold the tool pointed straight at the screw.
•
Use the proper bit for the head of the screw/bolt
that you wish to use.
•
When fastening screw M8 or smaller, carefully
adjust pressure on the switch trigger so that the
screw is not damaged.
•
If you tighten the screw for a time longer than
shown in the figures, the screw or the point of the
driver bit may be overstressed, stripped, damaged,
etc. Before starting your job, always perform a test
operation to determine the proper fastening time for
your screw.
The fastening torque is affected by a wide variety of
factors including the following. After fastening, always
check the torque with a torque wrench.
1.
When the battery cartridge is discharged almost
completely, voltage will drop and the fastening
torque will be reduced.
2.
Driver bit or socket bit
Failure to use the correct size driver bit or socket
bit will cause a reduction in the fastening torque.
3.
Bolt
•
Even though the torque coefficient and the
class of bolt are the same, the proper fastening
torque will differ according to the diameter of
bolt.
•
Even though the diameters of bolts are the
same, the proper fastening torque will differ
according to the torque coefficient, the class of
bolt and the bolt length.
The manner of holding the tool or the material of
4.
driving position to be fastened will affect the torque.
5.
Operating the tool at low speed will cause a
reduction in the fastening torque.
Standard bolt
Nm
(kgf cm)
M14
100
(1,020)
80
(816)
M12
(M14)
60
(612)
40
(408)
(M12)
M10
(M10)
M8
20
(204)
(M8)
Proper fastening torque
Fastening torque
120
(1,224)
0
0
1.0
2.0
Fastening time
3.0
(S)
012423
High tensile bolt
Nm
(kgf cm)
M12
(M12)
100
(1,020)
80
(816)
M10
60
(612)
(M10)
M8
40
(408)
(M8)
20
(204)
Proper fastening torque
Fastening torque
120
(1,224)
Hammer drill mode "
CAUTION:
Always hold the tool firmly during operation. There
is a tremendous and sudden twisting force exerted
on the tool/bit at the time of hole break-through,
when the hole becomes clogged with chips and
particles, or when striking reinforcing rods
embedded in the concrete.
Be sure to use a tungsten-carbide tipped bit.
Position the bit at the desired location for the hole, then
pull the switch trigger. Do not force the tool. Light
pressure gives best results. Keep the tool in position and
prevent it from slipping away from the hole.
•
0
0
1.0
2.0
Fastening time
"
3.0
(S)
012425
12
Do not apply more pressure when the hole becomes
clogged with chips or particles. Instead, run the tool at an
idle, then remove the bit partially from the hole. By
repeating this several times, the hole will be cleaned out
and normal drilling may be resumed.
Drilling mode "
Screwdriver mode "
CAUTION:
Adjust the number on the LED display to the proper
torque level for your work.
•
Make sure that the driver bit is inserted straight in
the screw head, or the screw and/or bit may be
damaged.
•
Hold the tool firmly. When the clutch cuts in or
refastening, a sudden twisting force may occur and
it can twist your wrist.
Place the point of the driver bit in the screw head and
apply pressure to the tool. Start the tool slowly and then
increase the speed gradually.
•
"
CAUTION:
Pressing excessively on the tool will not speed up
the drilling. In fact, this excessive pressure will only
serve to damage the tip of your bit, decrease the
tool performance and shorten the service life of the
tool.
•
There is a tremendous force exerted on the tool/bit
at the time of hole break through. Hold the tool
firmly and exert care when the bit begins to break
through the workpiece.
•
A stuck bit can be removed simply by setting the
reversing switch to reverse rotation in order to back
out. However, the tool may back out abruptly if you
do not hold it firmly.
•
Always secure small workpieces in a vise or similar
hold-down device.
•
Do not pull the switch trigger repeatedly when the
motor is locked. It may damage the tool.
For drilling in wood, the best results are obtained with
wood drills equipped with a guide screw. The guide
screw makes drilling easier by pulling the bit into the
workpiece.
For drilling in metal, to prevent the bit from slipping when
starting a hole, make an indentation with a center-punch
and hammer at the point to be drilled. Place the point of
the bit in the indentation and start drilling.
Use a cutting lubricant when drilling metals. The
exceptions are iron and brass which should be drilled dry.
•
NOTE:
•
This tool employs an electronic clutch. The tool
stops automatically when the clutch cuts in. To keep
operating, release the switch trigger once.
•
When driving wood screws, predrill pilot holes to
make driving easier and to prevent splitting of the
workpiece. See the chart.
Nominal diameter of wood screw
(mm)
Recommended size of pilot hole
(mm)
3.1
3.5
3.8
4.5
4.8
5.1
5.5
5.8
6.1
2.0 - 2.2
2.2 - 2.5
2.5 - 2.8
2.9 - 3.2
3.1 - 3.4
3.3 - 3.6
3.7 - 3.9
4.0 - 4.2
4.2 - 4.4
006421
NOTE:
•
See the following chart for the relation between the
number of torque setting and fastening torque rate.
The fastening torque rate will be different depends
on materials. Make a test fastening to get the
desired torque before operation.
NOTE:
•
Choose suitable speed for the work load. Drilling
over the following capacity may damage the tool.
Number
on LED
Display
Drilling capacity
Steel
6.5 mm
High speed
1
Wood
12 mm
Steel
10 mm
Wood
21 mm
"
3
Low speed
5
7
012989
9
012276
13
Fastening torque rate
Low (1)
Approx. 2.5 N .m
(Approx. 25.5 kgf. cm)
Approx. 4.6 N .m
(Approx. 46.9 kgf. cm)
Approx. 8.1 N .m
(Approx. 82.6 kgf. cm)
Approx. 10.0 N.m
(Approx. 102.0 kgf. cm)
Approx. 11.5 N.m
(Approx. 117.3 kgf. cm)
High (2)
Approx. 1.1 N .m
(Approx. 11.2 kgf. cm)
Approx. 2.0 N. m
(Approx. 20.4 kgf. cm)
Approx. 3.0 N .m
(Approx. 30.6 kgf. cm)
Approx. 4.0 N. m
(Approx. 40.8 kgf. cm)
Approx. 5.8 N .m
(Approx. 59.1 kgf. cm)
MAINTENANCE
CAUTION:
Always be sure that the tool is switched off and the
battery cartridge is removed before attempting to
perform inspection or maintenance except for the
following troubleshooting related to the light.
•
Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may
result.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.
•
OPTIONAL ACCESSORIES
CAUTION:
These
accessories
or
attachments
are
recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or
attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
•
Screw bits
•
Hook
•
Plastic carrying case
•
Makita genuine battery and charger
•
NOTE:
•
Some items in the list may be included in the tool
package as standard accessories. They may differ
from country to country.
14
15
Makita Jan-Baptist Vinkstraat 2, 3070, Belgium
Makita Corporation Anjo, Aichi, Japan
885309D225
www.makita.com
16
Download PDF
Similar pages