User manual
Micro
Strike
AH057
Please read carefully before use
Unpacking: Thank you for purchasing the AH057.
JM-MS has been tested and
JM-MS. Every AH057
shipped in perfect operating condition. Carefully check the shipping carton for damage
that may have occurred during shipping. If the carton appears to be damaged, carefully
inspect your fixture for any damage and be sure all equipment necessary to operate the
unit has arrived intact. In the event damage has been found or parts are missing, please
contact our toll free customer support number for further instructions. Please do not
return this unit to your dealer without contacting customer support first.
JM-MS is one DMX mode. The fixture can operate in three different
Introduction: The AH057
operating modes; DMX contorl, sound-active, or in a Master/Slave configuration. The
JM-MS comes with several built in programs that can be used, while operating as a
AH057
dimmer unit or when used in multiples linked in a master/slave configuration. For best
results use fog or special effects smoke to enhance the beams projections.
Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit
to rain or moisture.
Warning! This may cause severe eye damage. Avoid looking directly into the light
source at all times!
1
6
DMX control mode
Features
of AE022-5K
Features
Micro
Strike
● Color Strobe Effect
Channel
Value
Function
CH 1
0--255
Red (0%--100%)
CH 2
0--255
Green (0%--100%)
CH 3
0--255
Blue (0%--100%)
CH 4
0--255
White (0%--100%)
● Color Mix Effect
● LED Chases (Adjustable Speeds)
● Electronic Dimming 0-100%
● Built in Microphone
Channel
Value
Function
● DMX-512 protocol
CH 1
0--255
Master dimmer (0%--100%)
● 3 Operating Modes - Sound Active, Maser/Slave Mode, and DMX Control
CH 2
0--255
Red (0%--100%)
CH 3
0--255
Green (0%--100%)
CH 4
0--255
Blue (0%--100%)
CH 5
0--255
White (0%--100%)
CH 6
0--255
Adjust Strode when CH 6<16, adjust speed when CH 6>95
CH 7
● DMX-512 Protocol Compatible
● Digital Display for Address and Function Setting
Model:Micro
AE022-5K
Model
Strike
0-15
Dimmer
16-31
Color mixing plus change 1
32-47
Color mixing plus change 2
48-63
Color mixing plus change 3
64-79
Color mixing plus change 4
● Life Time:80000-100,000 hours
80-95
Color mixing plus change 5
96-111
Color sync strobe
● Dimming 0-100%with regulated constant color control
112-127
Color fade
● Strobe: 10 Flashed per second (any color)
128-143
Color sync
144-159
Colors mixing & change then Shuter closing
● Operation Mode:DMX 512,Manual,sound,internal program
160-175
down-dimming plus color change
176-191
Up-dimming plus color change
192-207
Color Up-dimming then down-dimming
208-223
Color mix change
224-239
Run sound mode 1
● Max Power:12W
240-255
Run sound mode 2
● Maximum Ambient Temperature:40℃
● Light Source: 3*R, 3*G, 3*B, 3*W 1Watt LEDs
● Beam Angle:25°
● DMX control: 4/7 DMX mode
● Control panel: Digital 4 characters alphanumeric
● Input voltage: AC100-240V, 50-60HZ (Power supply switch)
● G.W:1.0kg
Please Note: Specifications and improvements in the design of this unit and
this manual are subject to change without any prior written notice.
5
2
On Board System
Addr - DMX Address Setting via control board
1. Tap the MENU button and UP button or DOWN button until “Addr” is displayed, press ENTER.
2. “Axxx” will now be displayed, “x” represents the displayed address. Press the UP or DOWN buttons
to find your desired address.
Chnd - This menu will let you select your desired DMX Channel mode.
1. Tap the MENU button and UP button or DOWN button until “Chnd” is displayed, then press
ENTER.
2. “X Ch” now is displayed, “X” represents the displayed DMX channel mode. Press the UP or DOWN
buttons to find your desired Channel mode.
Soun - This menu will let you select your desired sound mode
1. Tap the MENU button until “Soun” is displayed, press ENTER.
2. “Soux” will now be displayed, you can confirm eight modes by UP or DOWN for sound mode.
Auto -This menu will let you select your desired auto mode
1. Tap the MENU button and UP button or DOWN button until “Auto” is displayed, press ENTER.
2. “Autx” will now be displayed, You can confirm eight modes by UP or DOWN for auto mode.
Colo - This menu will let you select your desired sound mode
1. Tap the MENU button and UP button or DOWN button until “CoLo” is displayed, press ENTER.
2. .Either “CoL X”, “X” representing a number between 1-9 or “AtF” will be displayed. Press the
UP or DOWN buttons to select either a static color or “AtF” mode. If you select a static color press
ENTER and it will be confirmed. “AtF” Make your own color by mixing and adjusting the red, blue and
green manually. Select “AtF”, press ENTER,“Rxxx” “Gxxx” or “Bxxx” will be displayed. then you can
adjust it between 0-255, press ENTER ,you can select other color by UP or DOWN to adjust it.
SLav- This menu will let you select your desired Master/slave mode
1. Tap the MENU button until “SLav” is displayed, press ENTER.
2. “Sla ” will now be displayed, Slave mode is confirmed. It will be slaved by auto mode sound mode
and chase mode
uer-This will display the software version
1. Press the UP or DOWN button until "uer" is dispalyed, press ENTER.
2. The software version will be displayed.
3
4
Distributed by Just Music GmbH
PO Box 024676, 10128 Berlin/Germany
Download PDF
Similar pages