SDS1000X-E
Series
DataSheet-2017.09
Super Phosphor
Oscilloscope
SDS1000X-E Series Digital Oscilloscope
Key Features
100 MHz, 200 MHz bandwidth models
Two channel series have one 1 GSa/s ADC, four channel series have
SDS1104X-E
SDS1204X-E
SDS1202X-E
two 1 GSa/s ADCs. When all channels are enabled, each channel has a
maximum sample rate of 500 MSa/s. When a single channel per ADC is
active, it has sample rate of 1 GSa/s
The newest generation of SPO technology
• Waveform capture rate up to 100,000 wfm/s (normal mode), and 400,000 wfm/s (sequence mode)
• Supports 256-level intensity grading and color display modes
Record length up to 14 Mpts
• Digital trigger system
Product overview
SIGLENT’s new SDS1000X-E Super Phosphor Oscilloscopes feature two
channel and four channel models. The two channel model is available with a
200 MHz analog bandwidth, a single ADC with a 1 GSa/s maximum sample
rate, and a single memory module with 14 Mpts of sample memory. The
Intelligent trigger: Edge, Slope, Pulse Width, Window, Runt, Interval,
Time out (Dropout), Pattern
Serial bus triggering and decoding (Standard), supports protocols IIC,
SPI, UART, RS232, CAN, LIN
Video trigger, supports HDTV
four channel scope is available in 100 and 200 MHz models and incorporates
Low background noisewith voltage scales from 500 μV/div to 10 V/div
two 1 GSa/s ADCs and two 14 Mpts memory modules. When all channels
10 types of one-button shortcuts, supports Auto Setup, Default, Cursors,
are enabled, each channel has sample rate of 500 MSa/s and a standard
Measure, Roll, History, Display/Persist, Clear Sweep, Zoom and Print
record length of 7 Mpts. When only a single channel per ADC is active, the
Segmented acquisition (Sequence) mode, divides the maximum record
maximum sample rate is 1 GSa/s and the maximum record length is 14 Mpts.
length into multiple segments (up to 80,000), according to trigger
For ease -of -use, the most commonly used functions can be accessed with
conditions set by the user, with a very small dead time segment to capture
its user- friendly front panel design.
the qualifying event.
History waveform record (History) function, maximum recorded waveform
The SDS1000X-E series employs a new generation of SPO (Super -Phosphor
Oscilloscope) technology that provides excellent signal fidelity and
performance. The system noise is also lower than similar products in the
industry. It comes with a minimum vertical input range of 500 uV/div, an
innovative digital trigger system with high sensitivity and low jitter, and
a waveform capture rate of 400,000 frames/sec (sequence mode). The
SDS1000X-E also employs a 256-level intensity grading display function
and a color temperature display mode not found in other models in this
class. SIGLENT’s latest oscilloscope offering supports multiple powerful
triggering modes including serial bus triggering. Serial bus decoding for IIC,
length is 80,000 frames.
Automatic measurement function for 38 parameters as well as
Measurement Statistics, Zoom, Gating, Math, History and Reference
functions
1 Mpts FFT
Math and measurement functions use all sampled data points (up to
14 Mpts)
Math functions (FFT, addition, subtraction, multiplication,division,
integration, differential, square root)
SPI, UART, CAN, LIN bus types is included. The X-E models also include
Preset key can be customized for user settings or factory “defaults”
History waveform recording, and sequential triggering that enable extended
Security Erase mode
waveform recording and analysis. Another powerful addition is the new
High Speed hardware based Pass/ Fail function
1 million point FFT math function that gives the SDS1000X-E very high
frequency resolution when observing signal spectra. The new digital design
also includes a hardware co-processor that delivers measurements quickly
and accurately without slowing acquisition and front-panel response. The
features and performance of SIGLENT’s new SDS1000X-E cannot be matched
anywhere else in this price class.
MSO, 16 digital channels (four channel series only, option)
Bode plot (four channel series only)
Search and navigate (four channel series only)
USB AWG module (four channel series only, option)
USB WIFI adapter (four channel series only, option)
Web Browser based control (four channel series only)
The four channel series includes even more functions, including: searching
and navigating, on-screen Bode plot, 16 digital channels (Option), an external
USB powered 25 MHz AWG module (Option), a USB WIFI adapter (Option),
and an embedded application that allows remote control via web browser.
Large 7 inch TFT -LCD display with 800 * 480 resolution
Multiple interface types: USB Host, USB Device (USB -TMC), LAN Pass /
Fail, Trigger Out
Supports SCPI remote control commands
Supports Multi-language display and embedded online help
WWW.SIGLENT.COM
SDS1000X-E Series Digital Oscilloscope
Models and key Specification
Model
SDS1104X-E
SDS1204X -E
SDS1202X-E
Bandwidth
100 MHz
200 MHz
SamplingRate (Max.)
Two channel series have a single 1 GSa/s ADC, four channel series have two 1 GSa/s ADCs. When all
channels are enabled, each channel has a maximum sample rate of 500 MSa/s. When a single channel per
pair is active, that channel has sample rate of 1 GSa/s
Channels
4 (four channel series)
2+EXT (two channel series)
Memory Depth (Max.)
7 Mpts/CH (not interleave mode);
14 Mpts/CH (interleave mode)
Waveform Capture Rate (Max.)
100,000 wfm/s (normal mode), 400,000 wfm/s (sequence mode)
Trigger Type
Edge, Slope, Pulse Width, Window, Runt, Interval, Dropout, Pattern, Video
Serial Trigger and decoder (Standard)
IIC, SPI, UART/RS232, CAN, LIN
16 Digital Channels (four channel series only,
option)
Maximum waveform capture rate up to 1 GSa/s, Record length up to 14 Mpts/CH
USB AWG module (four channel series only, option)
One channel, 25 MHz, sample rate of 125 MHz, wave length of 16 kpts
Bode plot ( four channel series only)
Minimum start frequency of 10 Hz, minimum scan bandwith of 500 Hz, maximum scan bandwidth of 120
MHz (dependent on Oscilloscope and AWG bandwidth), 500 maximum scan frequency points
USB WIFI adapter (four channel series only, option)
802.11b/g/b, WPA-PSK, the adapter must be supplied by Siglent to ensure working
I/O
USB Host, USB Device, LAN, Pass/Fail, Trigger Out, Sbus (Siglent MSO)
Probe (Std)
4 pcs passive probe PP510
Display
7 inch TFT -LCD (800x480)
Weight
Four channel series: Without package 2.6 Kg; With package 3.8 Kg
Two channel series: Without package 2.5 Kg; With package 3.5 Kg
4/2 pcs passive probe PP215
Function & Characteristics
7 inch TFT-LCD display and 10 one-button menus
Front panel of the four channel series
Front panel of the two channel series
• 7 -inch TFT -LCD display with 800 * 480 resolution
• Most commonly used functions are accessible using 10 different one-button operation keys: Auto Setup, Default, Cursor, Measure, Roll, History, Persist, Clear
Sweep, Zoom, Print
WWW.SIGLENT.COM
SDS1000X-E Series Digital Oscilloscope
Function & Characteristics
When all channels are enabled, each channel has a maximum sample rate of 500 MSa/s. When a single
channel per pair is active, that channel has sample rate of 1 GSa/s
The four channel series has two 1 GSa/s ADC chips (channel 1 and 2 share one, channel 3 and 4 share another), so that each channel can achieve sample rates up
to 500 MSa/and work on bandwidths of 200 MHz when all channels are enabled.
Record Length of Up to 14 Mpts (single
channel/pair mode), 7 Mpts/CH (two channels/
pair mode)
Waveform Capture Rate Up to 400,000 wfm/s
Using hardware-based Zoom technologies and max record length of up to
With a waveform capture rate of up to 400,000 wfm/s (sequence mode),
14 Mpts, users are able to oversample to capture for longer time periods
the oscilloscope can easily capture the unusual or low-probability events.
at higher resolution and use the zoom feature to see more details within
each signal.
256 -Level Intensity Grading and Color Temperature Display
SPO display technology provides for fast refresh rates. The resulting
The color temperature display is similar to the intensity-graded trace
intensity-graded trace is brighter for events that occur with more
function, but the trace occurrence is represented by different colors (color
frequency and dims when the events occur with less frequency.
“temperature”) as opposed to changes in the intensity of one color. Red
colors represents the more frequent events, while blue is used to mark
points that occur lest frequently.
WWW.SIGLENT.COM
SDS1000X-E Series Digital Oscilloscope
Serial Bus Decoding Function (Standard)
History Waveforms (History) Mode and
Segmented Acquisition (Sequence)
SDS1000X-E displays the decoding through the events list. Bus protocol
Playback the latest triggered events using the history function.
information can be quickly and intuitively displayed in a tabular format.
Segmented memory collection will store trigger events into multiple
(Up to 80,000) memory segments, each segment will store triggered
waveforms and timestamp each frame.
True measurement to 14 M points
Gate and Zoom Measurement
At any one timebase, SDS1000X-E can measure using all 14 M sample
Through Gate and Zoom measurement, the user can specify an arbitrary
points. This ensures the accuracy of measurements while the math co-
interval of waveform data analysis and statistics. This helps avoid
processor decreases measurement time and increases ease-of-use.
measurement errors that can be caused by invalid or extraneous data,
greatly enhancing the measurements’ validity and flexibility.
1 M points FFT
Hardware-Based High Speed Pass/ Fail
function
The new math co-processor enables FFT analysis of incoming signals
The SDS1000X-E utilizes a hardware-based Pass/Fail function, performing
using up to 1 M samples per waveform. This provides high frequency
up to 40,000 Pass / Fail decisions each second. Easily generate user
resolution with a fast refresh rate. The FFT function also supports a
defined test templates provide trace mask comparison making it suitable
variety of window functions so that it can adapt to different spectrum
for long-term signal monitoring or automated production line testing.
measurement needs.
WWW.SIGLENT.COM
SDS1000X-E Series Digital Oscilloscope
Customizable Default Key
16 Digital Channels/MSO (four channel series
only, option)
The current parameters of the oscilloscope can be preset to Default Key
16 digital channels enables users to acquire and trigger on the
through the Save menu.
waveforms then analyze the pattern, simultaneously with one instrument.
Search and Navigate (four channel series only)
The SDS1000X-E can search events specified by the user in a frame. It can also navigate by time (delay position) and historical frames.
Bode Plot (four channel series only)
SDS1000X-E can control the USB AWG module, control an independent SIGLENT SDG instrument, scan an object’s amplitude and phase frequency response, and
display the data as a Bode Plot. It can also show the result lists, and export the data to a USB disk.
WWW.SIGLENT.COM
SDS1000X-E Series Digital Oscilloscope
USB WIFI Adapter (four channel series only,
USB 25 MHz AWG Module (four channel series
option)
only, option)
USB WIFI Adapter
WiFi control of instrumentation can provide a convenient and safe
The four channel series supports a USB 25 MHz function/arbitrary
method of configuring and collecting data. This new feature works
waveform generator that is operated from the USB host connection.
with a SIGLENT approved WiFi adapter to provide wireless control and
Functions include Sine, Square, Ramp, Pulse, Noise, DC and 45 built-in
communications with SIGLENT 4 channel scopes. The adapter must be
waveforms. The arbitrary waveforms can be accessed and edited by the
supplied by Siglent to ensure working.
SIGLENT EasyWave PC software.
Complete Connectivity
Back panel of the four channel series
SDS1000X -E supports USB Host, USB Device (USB -TMC), LAN(VXI -11), Pass/Fail and Trigger Out
Web control (four channel series only)
With the new embedded web server, users can control the 4 channel
scopes from a simple web page. This provides wonderful remote
troubleshooting and monitoring capabilities.
WWW.SIGLENT.COM
Back panel of the two channel series
SDS1000X-E Series Digital Oscilloscope
Specifications
Acquire System
Sampling Rate
1 GSa/s (single channel/pair), 500 MSa/s (two channels/pair)
Memory Depth
Max 14 Mpts/Ch (single channel/pair), 7 Mpts/Ch (two channels/pair)
Peak Detect
2 nsec (Four channel series)
4 nsec (Two channel series)
Average
Averages:4, 16, 32, 64, 128, 256, 512, 1024
Eres
Enhance bits:0.5, 1.5, 2, 2.5, 3; Selectable
Waveform interpolation
Sin(x)/x, Linear
Input
Channels
4 (Four channel series)
2+EXT (Two channel series)
Coupling
DC, AC, GND
Impedance
DC: (1 MΩ±2%) || (15 pF ±2 pF) (Four channel series)
DC: (1 MΩ±2%) || (18 pF ±2 pF) (Two channel series)
Max.Input voltage
1 MΩ ≤400 Vpk(DC + Peak AC <=10 kHz)
CH to CH Isolation
DC-Max BW >40 dB
Probe attenuation
0.1X, 0.2X, 0.5X, 1X, 2X, 5X, 10X……1000X, 2000X, 5000X, 10000X
Vertical System
Bandwidth ( -3 dB )
200 MHz (SDS1204X-E/SDS1202X-E)
100 MHz (SDS1104X-E)
Vertical Resolution
8-bit
Vertical Scale (Probe 1X)
500 μV/div - 10 V/div (1-2-5 sequence )
Offset Range (Probe 1X)
Bandwidth Limit
500 μV- 150 mV: ± 2 V
152 mV- 1.5 V: ± 20 V
20 MHz ±40%
DC- 10% (BW): ± 1 dB
Bandwidth Flatness
10%- 50% (BW): ± 2 dB
50%- 100% (BW): + 2 dB/-3 dB
Low Frequency Response (AC -3 dB)
≤10 Hz (at input BNC)
ST-DEV ≤0.5 division (<1 mV/div)
Noise
ST-DEV ≤0.2 division (<2 mV/div)
ST-DEV ≤0.1 division (≥2 mV/div)
SFDR including harmonics
DC Gain Accuracy
Offset Accuracy
Risetime
Overshoot (500 ps Pulse)
≥35 dB
≤±3.0%: 5 mV/div-10 V/div
≤±4.0%: ≤2 mV/div
±(1%* Offset+1.5%*8*div+2 mV): ≥2 mV/div
±(1%* Offset+1.5%*8*div+500 uV): ≤1 mv/div
Typical 1.8 ns (SDS1204X-E/SDS1202X-E)
Typical 3.5 ns (SDS1104X-E)
<10%
WWW.SIGLENT.COM
SDS1000X-E Series Digital Oscilloscope
Horizontal System
Timebase Scale
1.0 ns/div-100 s/div
Channel Skew
<100 ps
Waveform Capture Rate
Up to 100,000 wfm/s (normal mode), 400,000 wfm/s (sequence mode)
Intensity grading
256 Levels
Display Format
Y -T, X -Y,Roll
Timebase Accuracy
±25 ppm
Roll Mode
50 ms/div-100 s/div (1-2-5 step)
Trigger System
Trigger Mode
Auto, Normal, Single
Internal: ±4.5 div from the center of the screen
Trigger Level
EXT: ±0.6 V (Two channel series)
EXT/5: ±3 V (Two channel series)
Holdoff Range
80 ns- 1.5 s
Trigger Coupling
AC
DC
LFRJ
HFRJ
Noise RJ
DC: Passes all components of the signal
Coupling Frequency Response
AC: Blocks DC components and attenuates signals below 8 Hz
LFRJ: Blocks the DC component and attenuates the low-frequency components below 2 MHz
HFRJ: Attenuates the high-frequency components above 1.2 MHz
DC: Passes all components of the signal
Coupling Frequency Response
LFRJ: Blocks the DC component and attenuates the low-frequency components below 10 KHz
HFRJ: Attenuates the high-frequency components above 500 KHz
components below 10 KHz
Internal: ±0.2 div
EXT (Two channel series): ±0.4 div
DC - Max BW 0.6 div
EXT (Two channel series): 200 mVpp DC– 10 MHz
Trigger Sensitivity
300 mVpp 10 MHz - BW frequency
EXT/5 (Two channel series): 1 Vpp DC – 10 MHz
1.5 Vpp 10 MHz -BW frequency
Trigger Jitter
< 100 ps
Trigger Displacement
Pre-Trigger: 0 - 100% Memory
Delay Trigger: 0 to 10,000 div
Edge Trigger
Slope
Rising, Falling, Rising&Falling
Source
All channels/ EXT/ (EXT/5)/ AC Line (Two channel series)
All channels/ AC Line (Four channel series)
Slope Trigger
Slope
Rising, Falling
LimitRange
< , > , <> , ><
Source
All channels
TimeRange
2 ns- 4.2 s
Resolution
1 ns
WWW.SIGLENT.COM
SDS1000X-E Series Digital Oscilloscope
Pulse Trigger
Polarity
+wid , -wid
Limit Range
< , > , <> , ><
Source
All channels
Pulse Range
2 ns ~ 4.2 s
Resolution
1 ns
Video Trigger
Signal Standard
NTSC,PAL,720p/50,720p/60,1080p/50,1080p/60,1080i/50,1080i/60,Custom
Source
All channels
Sync
Any, Select
Trigger condition
Line, Field
Window Trigger
Window Type
Absolute, Relative
Source
All channels
Interval Trigger
Slope
Rising, Falling
Limit Range
< , > , <> , ><
Source
All channels
Time Range
2 ns ~ 4.2 s
Resolution
1 ns
Dropout Trigger
Timeout Type
Edge, State
Source
All channels
Slope
Rising, Falling
Time Range
2 ns ~ 4.2 s
Resolution
1 ns
Runt Trigger
Polarity
+wid , -wid
Limit Range
< , > , <> , ><
Source
All channels
Time Range
2 ns ~ 4.2 s
Resolution
1 ns
Pattern Trigger
Pattern Setting
Invalid, Low, High
Logic
AND, OR, NAND, NOR
Source
All channels
Limit Range
< , > , <> , ><
Time Range
2 ns ~ 4.2 s
Resolution
1 ns
WWW.SIGLENT.COM
SDS1000X-E Series Digital Oscilloscope
Serial Trigger
I2C Trigger
Condition
Start, Stop, Restart, No Ack, EEPROM, 7 bits Address & Data, 10 bits Address & Data, Data Length
Source (SDA/SCL)
All channels
Data format
Hex
Limit Range
EEPROM: =, >, <
Data Length
EEPROM: 1 byte
Addr & Data: 1 ~ 2 byte
Data Length: 1 ~ 12 byte
R/W bit
Addr & Data: Read, Write, Do not care
SPI Trigger
Condition
Data
Source (CS/CL/Data)
All channels
Data format
Binary
Data Length
4 ~ 96 bit
Bit Value
0, 1, X
Bit Order
LSB, MSB
UART/ RS232 Trigger
Condition
Start, Stop, Data, Parity Error
Source (RX/TX)
All channels
Data format
Hex
Limit Range
=, >, <
Data Length
1 byte
Data Width
5 bit, 6 bit, 7 bit, 8 bit
Parity Check
None, Odd, Even
Stop Bit
1 bit, 1.5 bit, 2 bit
Idle Level
High, Low
Baud (Selectable)
600/1200/2400/4800/960019200/38400/57600/115200 bit/s
(Custom)
300 bit/s ~ 334000 bit/s
CAN Trigger
Condition
All, Remote, ID, ID + Data, Error
Source
All channels
ID
STD (11 bit), EXT (29 bit)
Data Format
Hex
Data Length
1~2 byte
Baud Rate (Selectable)
5 k/10 k/20 k/50 k/100 k/125 k/250 k/500 k/800 k/1 M bit/s
Baud Rate (Custom)
5 kbit/s~1 Mbit/s
LIN Trigger
Condition
Break, Frame ID, ID+Data, Error
Source
All channels
ID
1 byte
Data Format
Hex
Data Length
1 ~ 2 byte
Baud Rate (Selectable)
600/1200/2400/4800/9600/19200 bit/s
Baud Rate (Custom)
300 bit/s ~ 20 kbit/s
WWW.SIGLENT.COM
SDS1000X-E Series Digital Oscilloscope
Serial Decoder
I2C Decoder
Signal
SCL, SDA
Address
7 bits, 10 bits
Threshold
-4.5 ~ 4.5 div
List
1 ~ 7 lines
SPI Decoder
Signal
SCL,MISO, MOSI, CS *NOTE 2 channel scopes can only use 2 signal identifiers
Edge Select
Rising, Falling
Idle Level
Low, High
Bit Order
MSB, LSB
Threshold
-4.5 ~ 4.5 div
List
1 ~ 7 lines
UART/ RS232 Decoder
Signal
RX, TX
Data Width
5 bit,6 bit,7 bit,8 bit
Parity Check
None, Odd, Even
Stop Bit
1 bit, 1.5 bit, 2 bit
Idle Level
Low, High
Threshold
-4.5 ~ 4.5 div
List
1 ~ 7 lines
CAN Decoder
Signal
CAN_H, CAN_L
Source
CAN_H, CAN_L, CAN_H-CAN_L
Threshold
-4.5 ~ 4.5 div
List
1 ~ 7 lines
LIN Decoder
LIN Specification Package Revision
Ver1.3, Ver2.0
Threshold
-4.5 ~ 4.5 div
List
1 ~ 7 lines
WWW.SIGLENT.COM
SDS1000X-E Series Digital Oscilloscope
Measurement
Source
All channels, All channels in Zoom, Math, All References, History
Number of Measurements
Display 5 measurements at the same time
Measurement Range
Screen region, Gate region
Measurement Parameters ( 38 Types )
Vertical(Voltage)
Horizontal(Time)
Delay
WWW.SIGLENT.COM
Max
Highest value in input waveform
Min
Lowest value in input waveform
Pk-Pk
Difference between maximum and minimum data values
Ampl
Difference between top and base in a bimodal signal, or between max and min in an unimodal signal
Top
Value of most probable higher state in a bimodal waveform
Base
Value of most probable lower state in a bimodal waveform
Mean
Average of all data values
Cmean
Average of data values in the first cycle
Stdev
Standard deviation of all data values
Cstd
Standard deviation of all data values in the first cycle
VRMS
Root mean square of all data values
Crms
Root mean square of all data values in the first cycle
FOV
Overshoot after a falling edge; (base-min)/Amplitude
FPRE
Overshoot before a falling edge; (max-top)/Amplitude
ROV
Overshoot after a rising edge; (max-top)/Amplitude
RPRE
Overshoot before a rising edge; (base-min)/Amplitude
Level@X
the voltage value of the trigger point
Period
Period for every cycle in waveform at the 50% level, and positive slope
Freq
Frequency for every cycle in waveform at the 50% level, and positive slope
+Wid
Width measured at 50% level and positive slope
-Wid
Width measured at 50% level and negative slope
Rise Time
Duration of rising edge from 10-90%
Fall Time
Duration of falling edge from 90-10%
Bwid
Time from the first rising edge to the last falling edge, or the first falling edge to the last rising edge at the 50%
crossing
+Dut
Ratio of positive width to period
-Dut
Ratio of negative width to period
Delay
Time from the trigger to the first transition at the 50% crossing
Time@Level
Time from the trigger to each rising edge at the 50% crossing.
When Statistics is Off, it shows the time from the trigger to the last rising edge at the 50% crossing.
When Statistics is On, it shows the Current, Mean, Min, Max, Standard Deviation of time from the trigger to each
rising edge at the 50% crossing in multiple frames (number = Count).
Phase
Calculate the phase difference between two edges
FRR
Time between the first rising edges of the two channels
FRF
Time from the first rising edge of channel A to the first falling edge of channel B
FFR
Time from the first falling edge of channel A to the first rising edge of channel B
FFF
Time from the first falling edge of channel A to the first falling edge of channel B
LRR
Time from the first rising edge of channel A to the last rising edge of channel B
LRF
Time from the first rising edge of channel A to the last falling edge of channel B
LFR
Time from the first falling edge of channel A to the last rising edge of channel B
LFF
Time from the first falling edge of channel A to the last falling edge of channel B
Skew
Time of source A edge minus time of nearest source B edge
SDS1000X-E Series Digital Oscilloscope
Measurement
Cursors
Manual : Time X1, X2, (X1-X2), (1/ΔT)
Track: Time X1, X2, (X1-X2)
Voltage Y1, Y2, (Y1-Y2)
Statistics
Current, Mean, Min, Max, Stdev, Count
Counter
Hardware 6 bit counter(channels are selectable)
Math Function
Operation
+ , - , * , / , FFT , d/dt , ∫dt , √
FFT window
Rectangular, Blackman, Hanning, Hamming, Flattop
FFT display
Full Screen, Split, Exclusive
Number of Decoders
2
USB AWG Module (four channel series only, option)
Channel
1
Max. Output Frequency
25 MHz
Sampling Rate
125 MSa/s
Frequency Resolution
1 μHz
Frequency Accuracy
±50 ppm
Vertical Resolution
14-bits
AmplitudeRange
-1.5 ~ +1.5 V (50Ω)
-3 ~ +3 V (High-Z)
Waveform Type
Sine, Square, Ramp, pulse, Noise, DC and 45 built-in waveforms
Output impedance
50 Ω±2%
Protection
Over-Voltage Protection, Current-Limiting Protection
Sine
Frequency
1 μHz ~ 25 MHz
Offset Accuracy (10 kHz)
±(1%*Offset Setting Value +1 mVpp)
Amplitude flatness
(10 kHz, 5 Vpp)
±0.3 dB
DC ~ 1 MHz
SFDR
-60 dBc
1 MHz ~ 5 MHz -55 dBc
5 MHz ~ 25 MHz -50 dBc
HD
DC ~ 5 MHz
-50 dBc
5 MHz ~ 25 MHz -45 dBc
Square/Pulse
Frequency
1 μHz ~ 10 MHz
Duty Cycle
1% ~ 99%
Rise/Fall time
< 24 ns (10% ~ 90%)
Overshoot (1 kHz,1 Vpp, Typical)
< 3% (typical 1 kHz, 1 Vpp)
Pulse Width
> 50 ns
Jitter
< 500 ps + 10 ppm
Ramp
Frequency
1 μHz ~ 300 kHz
Linearity (Typical)
< 0.1% of Pk-Pk (Typical, 1 kHz, 1 Vpp, 100% Symmetry)
Symmetry
0% ~ 100% (Adjustable)
WWW.SIGLENT.COM
SDS1000X-E Series Digital Oscilloscope
DC
Offset range
Accuracy
±1.5 V (50 Ω)
±3 V (High-Z)
±(|offset|*1%+3 mV)
Noise
Bandwidth
>25 MHz (-3 dB)
Arbitrary Wave
Frequency
1 μHz ~ 5 MHz
Wave Length
16 kpts
Sampling Rate
125 MSa/s
Lead in
EasyWave and U-Disk
Digital Channels (four channel series only, option)
No. of Channels
16
Max. Sampling Rate
1 GSa/s
Memory Depth
14 Mpts/CH
Min. Detectable Pulse Width
4 ns
Level Group
D0~D7, D8~D15
Level Range
-3 V ~ 3 V
Logic Type
TTL, CMOS, LVCMOS3.3, LVCMOS2.5, custom
Skew[2]
D0~D15: ±1 sampling interval
Digital to Analog: ± (1 sampling interval +1 ns)
I/O
Standard
USB Host, USB Device, LAN, Pass/Fail, Trigger Out
Pass/Fail
3.3 V TTL Output
Display (Screen)
Display Type
7-inch TFT LCD
Display Resolution
800×480
Display Color
24 bit
Contrast (Typical)
500:1
Backlight
300 nit
Range
8 x 14 divisions
Display (Waveform)
Display Mode
Dot, Vector
Persist Time
Off, 1 Sec, 5 Sec, 10 Sec, 30 Sec, Infinite
Color Display
Normal, Color
Screen Saver
1 min, 5 min, 10 min, 30 min, 1 hour, Off
Language
Simplified Chinese, Traditional Chinese, English, French, Japanese, Korean, German, Russian, Italian, Portuguese
WWW.SIGLENT.COM
SDS1000X-E Series Digital Oscilloscope
Environments
Temperature
Operating: 10℃ ~ +40℃
Non-operating: -20℃ ~ +60℃
Humidity
Operating: 85% RH, 40℃ , 24 hours
Non-operating: 85% RH, 65℃ , 24 hours
Height
Operating: ≤3000 m
Non-operating: ≤15,266 m
Electromagnetic Compatibility
2004/108/EC)
Execution Standard EN 61326-1:2006
EN 61000-3-2:2006 + A2:2009, EN 61000-3-3:2008
Safety
2006/95/EC
Execution Standard EN 61010-1:2010/
EN 61010-2-030:2010
Power Supply
Input Voltage
100 ~ 240 VAC, CAT II, Auto selection
Frequency
50/60/400 Hz
Power
25 W Max
Mechanical (Four channel series)
Length: 312 mm
Dimensions
Width: 132.6 mm
Height: 151 mm
Weight
N.W: 2.6 kg; G.W: 3.8 kg
Mechanical (Two channel series)
Length: 312 mm
Dimensions
Width: 134 mm
Height: 150 mm
Weight
N.W: 2.5 Kg; G.W: 3.5 Kg
WWW.SIGLENT.COM
SDS1000X-E Series Digital Oscilloscope
Probes and Accessories
Probe
Passive
Picture
Model
Description
PB470
Bandwidth: 70 MHz, 1X/10X, 1M/10 Mohm, 300 V/600 V
PP510
Bandwidth: 100 MHz, 1X/10X, 1M/10 Mohm,300 V/600 V
PP215
Bandwidth: 200 MHz, 1X/10X, 1M/10 Mohm, 300 V/600 V
Bandwidth: 100 KHz, Max. continuous current: 20 Arms, Peak current: 60 A
CP4020
Switch Ratio: 50 mV/A, 5 mV/A, Accuracy: 50 mV/A (0.4 A-10 Apk)±2%, 5
mV/A (1 A-60 Apk) ±2%, 9 V battery source
CP4050
Bandwidth: 1 MHz, Max. continuous current: 50 Arms, Peak current: 140 A
Switch Ratio: 500 mV/A, 50 mV/A
Accuracy: 500 mV/A (20 mA-14 ApK )±3% ±20 mA , 50 mV/A (200 mA100 ApK) ±4%±200 mA, 50 mV/A (100 A-140 ApK) ±15% max, 9V battery
source
Bandwidth: 150 KHz, Max. continuous current: 70 Arms, Peak current: 200 A
CP4070
Switch Ratio: 50 mV/A, 5 mV/A, Accuracy: 50 mV/A (0.4 A-10 ApK)±2% , 5
mV/A (1 A-200 ApK) ±2%, 9V battery source
CP4070A
Bandwidth: 300 KHz, Max. continuous current: 70 Arms, Peak current: 200 A
Switch Ratio: 100 mV/A, 10 mV/A, Accuracy: 100 mV/A (50 m A-10
ApK)±3%±50 mA , 10 mV/A (500 mA-40 ApK)±4%±50 mA, 10 mV/A (40
A-200 ApK)±15% max, 9 V battery source
Current Probe
CP5030
Bandwidth: 50 MHz, Max. continuous current: 30 Arms, Peak current: 50 A
Switch Ratio: 100 mV/A, 1 V/A, Accuracy: 1 V/A (±1%±1 mA), 100 mV/A
(±1%±10 mA), DC 12 V/ 1.2 A power adapter
Bandwidth: 100 MHz, Max. continuous current: 30 Arms, Peak current: 50 A
CP5030A
Switch Ratio: 100 mV/A, 1 V/A, Accuracy: 1 V/A (±1%±1 mA), 100 mV/A
(±1%±10 mA), DC 12V/1.2A power adapter
CP5150
Bandwidth: 12 MHz, Max. continuous current: 150 Arms, Peak current: 300 A
Switch Ratio: 100 mV/A, 10 mV/A, Accuracy: 100 mV/A (±1%±10 mA), 10
mV/A (±1%±100 mA), DC 12 V/1.2 A power adapter
Bandwidth: 5 MHz, Max. continuous current: 500 Arms, Peak current: 750 A
CP5500
Switch Ratio: 100 mV/A, 10 mV/A, Accuracy: 100 mV/A (±1%±10 mA), 10
mV/A (±1%±100 mA), DC 12 V/1.2 A power adapter
Differential Probe
DPB4080
WWW.SIGLENT.COM
Bandwidth: 50 MHz, Differential Range: 800 V (DC + Peak AC),
100 X/200 X/500 X/1000 X, Accuracy: ±1%, DC 9 V/1 A power adapter
SDS1000X-E Series Digital Oscilloscope
Probe
Picture
DPB5150
DPB5150A
Model
Description
Bandwidth: 70 MHz, Differential Range: 1500 V (DC + Peak AC),50 X/500 X
Accuracy: ±2%, DC 5 V/1 A USB adapter
Bandwidth: 100 MHz, Differential Range: 1500 V (DC + Peak AC),
50X/500X , Accuracy: ±2% DC 5 V/1 A USB adapter
Differential Probe
Bandwidth: 70 MHz, Differential Range: 7000 V (DC + Peak AC),
DPB5700
100X/1000X , Accuracy: ±2%,
DC 5 V/1 A USB adapter
Bandwidth: 100 MHz
Differential Range: 7000 V (DC + Peak AC),
DPB5700A
100X/1000X
Accuracy: ±2%
DC 5 V/1 A USB adapter
Bandwidth: 40 MHz
High Voltage
HPB4010
Differential Range: DC 10 KV, AC (rms): 7 KV (sine), AC (Vpp): 20 KV (Pulse)
1000X
Accuracy: ≤3%
The USB Device interface allows a connection into the GPIB interface. USB-
Isolated front end
ISFE
GPIB adapter allows the oscilloscope to easily send and receive commands
through the GPIB. USB follows the USB2.0 specification. GPIB follows the
IEEE488.2 standard.
Demo Board
STB-3
USB AWG Module
SAG1021
Output signals include square waves, sine, AM, fast edge , pulse, PWM, I2C,
CAN, LIN etc. Used in teaching and demonstrations.
Output Sine, Square, Ramp, pulse, Noise, DC and 45 built-in waveforms.
The arbitrary waveforms can be accessed and edited by the EasyWave PC
software
WWW.SIGLENT.COM
SDS1000X-E Series Digital Oscilloscope
Ordering information
SDS1000X-E Series Digital Oscilloscope
Product Name
SDS1104X-E 100 MHz Four Channels
SDS1204X-E 200 MHz Four Channels
SDS1202X-E 200 MHz Two Channels
USB Cable -1
Quick Start -1
Standard Accessories
Passive Probe -4/2
Certification -1
Power Cord -1
Optional Accessories
16 Channels MSO Software (four channel series only)
SDS1000X-E-16LA
16 Channels Logic Analyzer (four channel series only)
SLA1016
AWG Software (four channel series only)
SDS1000X-E-FG
USB AWG Module Hardware (four channel series only)
SAG1021
WIFI Software (four channel series only)
SDS1000X-E-WIFI
USB WIFI Adapter (four channel series only)
TL_WN725N
Isolated Front End
ISFE
STB Demo Source
STB-3
High Voltage Probe
HPB4010
Current Probes
Differential Probes
WWW.SIGLENT.COM
CP4020/CP4050/CP4070/CP4070A/CP5030/CP5030A/
CP5150/CP5500
DPB4080/DPB5150/DPB5150A/DPB5700/DPB5700A
SDS1000X-E
Series
Super Phosphor
Oscilloscope
About SIGLENT
SIGLENT is an international high-tech company, concentrating on R&D, sales,
production and services of electronic test & measurement instruments.
SIGLENT first began developing digital oscilloscopes independently in 2002. After
more than a decade of continuous development, SIGLENT has extended its
product line to include digital oscilloscopes, function/arbitrary waveform
generators, digital multimeters, DC power supplies, spectrum analyzers, isolated
handheld oscilloscopes and other general purpose test instrumentation. Since its
first oscilloscope, the ADS7000 series, was launched in 2005, SIGLENT has
become the fastest growing manufacturer of digital oscilloscopes. We firmly
believe that today SIGLENT is the best value in electronic test & measurement.
Headquarter:
SIGLENT TECHNOLOGIES CO., LTD.
Add: Bldg No.4 & No.5, Antongda Industrial
Zone, 3rd Liuxian Road, Bao'an District,
Shenzhen, 518101, China.
Tel: + 86 755 3661 5186
Fax: + 86 755 3359 1582
Email: sales@siglent.com;
Website: http://www.siglent.com/ens/
USA:
SIGLENT Technologies America, Inc
6557 Cochran Rd Solon, Ohio 44139
Tel: 440-398-5800
Toll Free: 877-515-5551
Fax: 440-399-1211
Email: info@siglent.com
Website: www.siglentamerica.com
Europe:
SIGLENT TECHNOLOGIES EUROPE GmbH
ADD: Liebigstrasse 2-20,
Gebaeude 14,
22113 Hamburg Germany
Tel: +49(0)-819-95946
Fax: +49(0)-819-95947
Email: info-eu@siglent.com
Website: www.siglenteu.com
Follow us on
Facebook: SiglentTech
Download PDF
Similar pages