32VDC ESL600 Series Brushless Screwdrivers

32VDC ESL600 Series Brushless Screwdrivers & Controllers
Operation Manual
CAUTION - Please read, understand, and follow all operating and safety instructions in
this manual before using the Tools and Controllers.
The 32VDC 600 Series tools are designed for exclusive use with specific Delta Regis
controllers as defined in this manual. Do not attempt to use the tools and/or controllers in
with any products other than as specified in this manual.
If you have any questions or concerns, please contact us at:
Delta Regis Tools, Inc.
3315 Industrial 25th St.
Ft. Pierce FL 34946
USA
Doc. 32V_Brushless_Series_Manual_R2
Copyright © 2011 Delta Regis Tools, Inc
Ph +1-772-465-4302
Fx +1-772-465-4368
E-mail: sales@deltaregis.com
Website: www.deltaregis.com
ESL600 Series
Operation Manual
Important - Installation and Safety
Warning - Failure to understand and follow proper installation guidelines, safety requirements,
and operating instructions may result in malfunction, component damage, property damage,
shock hazard, fire hazard, injury or death.
1. Please read and understand the operation manual and follow all safety and operation instructions.
2. Use these products in a suitable dry, indoor location. Do not use the tools and controllers in damp,
wet or high temperature environments. Do not use in the presence of flammable liquids or gases.
3. Ensure that the controller has proper ventilation. Do not expose the tools and controllers to areas
subject to airborne contaminants (eg. dust, metal filings).
4. Use only a properly grounded electrical outlet of the correct supply voltage to power the screwdriver
controller. Ensure that the supply outlet is overload protected and of sufficient amperage capacity.
5. Use only the correct plug for the controller and outlet. Hold the plug of the power cord when
connecting or disconnecting. Do not pull on the cable.
6. Do not expose the cable, tool or controller to oil, chemicals, or heat. Ensure that the cable is routed
and used in such a manner as to not be subject to sharp objects that may abrade or cut the cable.
7. Locate the controller in a suitable, safe location on a steady surface. Do not place in a high location
where there may be a risk of it falling. Secure the controller in position to prevent possible movement
caused by pulling on the power or tool cables.
8. Do not cover the controller or stack any objects on top of or near the controller. Ensure that adequate
clearance and ventilation is provided around the perimeter of the controller.
9. The ‘BECT6’ series controllers are for use exclusively with Delta Regis brand ‘ESL6’ series
screwdrivers as specified on the following pages. Use of the controller (or screwdriver) with any
other screwdriver (or controller) may result in malfunction, damage, or injury.
10.In the event that the controller is overloaded beyond the maximum current rating, an internal fuse will
disrupt power. Should the controller stop functioning, or exhibit abnormal or intermittent operation,
please discontinue use immediately and send the controller to an authorized service centre for
troubleshooting and repair.
11. Excessive duty cycle will cause the tool and/or controller to overheat. If this occurs, discontinue use
until cooled down and reduce cycle rate. As a general rule, do not exceed 10-15 screws/minute.
12.The ‘ESL6’ series screwdrivers incorporate a protection circuit which stops the electric screwdriver
if the tool is switched from forward to reverse while running. Should this happen, the operator must
release the tool trigger and restart the fastening cycle.
13.Turn the main power switch off when the controller is not being used. Unplug the controller if it is not
being used on a regular basis.
14.Do not attempt to disassemble or repair the screwdriver or controller. Repairs should only be
performed by qualified technicians properly trained in the safe operation, troubleshooting, and repair
of these devices. Please consult Delta Regis for the location of the nearest service depot.
15.Use only the factory specified Delta Regis brand replacement parts and accessories with these tools
and controllers.
16.Any damage to the tool and/or controller resulting from misuse, abuse, or failure to follow these
guidelines will void the limited product warranty.
Grounding - This controller (and AC power cord) is equipped with a 3-prong electrical receptacle/plug
with ground pin. The controller must be connected to a properly grounded AC electrical outlet. Do not
attempt to use this controller without a properly functioning ground connection. Never connect a live
circuit to the ground pin or internal yellow-green ground wire.
www.deltaregis.com
Page 2
ESL600 Series
Operation Manual
Inserting / Removing Bits
Push the bit retainer inwards and it will release. The bit can now be inserted or removed.
Adjusting Torque
1. Determine the torque output of the tool by checking a tightened
fastener with a torque wrench.
2. Increase or decrease the torque by rotating the Torque Adjustment
Ring.
3. Rotating the Ring clockwise increases torque output.
4. Rotating the Ring counterclockwise decreases torque output.
5. Check the adjustment with a torque wrench. A number of factors
will affect torque output from one application to another. Final
torque adjustment should be made on the application through a of
series of gradual increases. Always start below the desired torque
and work upward.
6. Remove the housing nut from the electric screwdriver after setting
the desired torque and attach the torque locking sleeve. This will
help avoid accidental torque adjustment.
Note: The numbers on the torque scale are for reference only and do
not indicate actual torque value.
Proper Grip
To prevent damage to your investment, it is essential that all users have a proper
and secure grip on the screwdriver at all times. As shown, the user has a firm grip
on the screwdriver with the FWD/REV switch easily reached with the thumb and
the start lever with the index finger.
Note: A firm grip is required to prevent the tool from spinning and possibly
damaging the unit.
Operation
1. Insert the power plug into a receptacle and set the FWD/REV switch to the “F” position.
2. Apply the bit to the screw head and press the lever or push the tool downward, the start switch will be
turned ON and the motor will start running.
3. Once the screw has tightened and reached the torque you had set, the tool will shutoff automatically.
4. To reset the tool, release the lever or release the bit from the screw head.
5. To remove the screw, set the FWD/REV switch to the “R” position.
www.deltaregis.com
Page 3
ESL600 Series
Operation Manual
Specifications
• Precise Torque Control, Low Torque Reaction.
600 Series
• Quiet, Brushless DC motor means no carbon dust.
• Compact body design results in exceptional
manouverability and operator comfort.
• Less heat build-up and higher duty cycle capabilities than
conventional brush motors. 3 year motor warranty.
• Brushless design results in low maintenance.
• 32VDC Screwdrivers feature ESD safe housings.
• CE, RoHS Compliant.
32VDC Brushless Screwdrivers
Model Number (1)
Start
Type
Range
(In.Lbs)
Range
(Nm)
Speed
(RPM) Hi
Speed
(RPM) Lo
(C)ESL610-ESD
Lever
0.2 - 3.1
0.02 - 0.35
1000
700
(C)ESL611-ESD
Lever
0.4 - 6.2
0.05 - 0.69
1000
(C)ESL612-ESD
Lever
0.9 - 8.7
0.10 - 0.98
(C)ESL623-ESD
Lever
1.3 - 10.5
0.15 - 1.18
Lever
1.3 - 10.5
(C)ESL623P-ESD
Push
(C)ESL623PF-ESD (2)
Push
(C)ESL624-ESD
(C)ESL624P-ESD
(C)ESL623F-ESD
(2)
Screwdriver
Bit Type
Length
(mm)
Diameter
(mm)
Weight
(g)
4mm
185
32
385
700
4mm
185
32
385
1000
700
4mm
185
32
385
1000
650
1/4” hex
245
36
520
0.15 - 1.18
2000
---
1/4” hex
245
36
520
1.3 - 10.5
0.15 - 1.18
1000
650
1/4” hex
245
36
520
1.3 - 10.5
0.15 - 1.18
2000
---
1/4” hex
245
36
520
Lever
2.6 - 16.5
0.29 - 1.86
1000
650
1/4” hex
245
36
520
Push
2.6 - 16.5
0.29 - 1.86
1000
650
1/4” hex
245
36
520
Screwdriver models with a ‘C’ prefix have a 6-pin cable connector for use with BECT620C and BECT620IC controllers, or for use with
the BECT626-SSO Counting Controller. Refer to BECT626-SSO manual for counting controller operation and use.
(2)
For fast screwdriver models ESL623F-ESD and ESL623PF-ESD, use controller model BECT620I (4 pin controller).
For fast screwdriver models CESL623F-ESD and CESL623PF-ESD, use controller model BECT620IC (6 pin controller).
(1)
32VDC Brushless Power Controller
The BECT620 and BECT620I Controllers are designed specifically to run our 32V Brushless Screwdrivers. These
compact, lightweight controllers accepts input voltages of 100-240VAC, 50/60Hz (1.2A). Output voltage to the
driver is 32VDC on the high speed setting and 24 or 20VDC on low speed. CE/RoHS/ETL Approved.
Model Number Outlets
Speeds
Tool
Connector
Output
Input
Dimensions
L x W x H (mm)
Weight
(g)
BECT620
1
Hi/Lo
4 pin
32/20V DC
100-240VAC, 50/60 Hz, 1.2A
145 x 60 x 35
250
BECT620I
1
Hi/Lo
4 pin
32/24V DC
100-240VAC, 50/60 Hz, 1.2A
195 x 76 x 56
450
BECT620C
1
Hi/Lo
6 pin
32/20V DC
100-240VAC, 50/60 Hz, 1.2A
145 x 60 x 35
250
BECT620IC
1
Hi/Lo
6 pin
32/24V DC
100-240VAC, 50/60 Hz, 1.2A
195 x 76 x 56
450
Power supply shipped with standard North American cordset. For EU cord, add suffix ‘E’ ; for UK cord add suffix ‘UK’ to part number.
www.deltaregis.com
Page 4
ESL600 Series
Operation Manual
Torque Adjusting Nut
Turn to adjust torque. Higher values on scale
indicate higher torque. Numbers on the scale
are for reference only and are not a torque
indication.are not a torque indication.
Trigger
Bit Holder
Retract sleeve to
insert/remove bits.
Suspension Ring
Use to suspend the tool.
Housing Nut
Remove housing nut to
install torque locking sleeve.
Forward/Reverse Switch
Three position switch with center position
being OFF. The OFF position is recommended
when changing bits.
Service
The ‘BECT6’ Series Controllers are not user serviceable. Any repairs must be performed by a Delta Regis
authorized service center. Please consult Delta Regis Tools for further information and the location of the
nearest authorized service center.
Repairs to ‘ESL6’ series screwdrivers must be performed by trained personnel, knowledgeable and
qualified in the repair of DC electric screwdrivers. Use only genuine Delta Regis parts when servicing
these products.
Do not attempt to modify the tools or controllers.
Warranty
The ESL600 Series Tools and Controllers are warranted for one year from the date of purchase against
defects in material and workmanship. In addition, the brushless motor in the ESL600 Series Screwdrivers is warranted for three years from the date of purchase against defects in material and workmanship.
This warranty does not cover damage due to transportation, abuse, misuse, or improper service. Our sole
remedy is to repair or replace (at our discretion) any unit found to be defective due to defects in material
or workmanship. It is the responsibility of the user to return any product thought to be defective, freight
prepaid, to our warehouse for inspection and evaluation.
There is no warranty of merchantability or fitness of purpose. In no event will Delta Regis Tools, Inc.
be liable for business interruptions, loss of profits, harm, injury, damage, personal injury, cost of delay,
or any other special, indirect, incidental, or consequential losses, costs, or damages.
www.deltaregis.com
Page 5
Download PDF
Similar pages