FILE NO. 140-200116
SERVICE MANUAL
COLOR TELEVISION/
VIDEO CASSETTE RECORDER
MV20FL4
SERVICING NOTICES ON CHECKING
1. KEEP THE NOTICES
6. AVOID AN X-RAY
As for the places which need special attentions,
they are indicated with the labels or seals on the
cabinet, chassis and parts. Make sure to keep the
indications and notices in the operation manual.
2. AVOID AN ELECTRIC SHOCK
There is a high voltage part inside. Avoid an
electric shock while the electric current is
flowing.
3. USE THE DESIGNATED PARTS
The parts in this equipment have the specific
characters of incombustibility and withstand
voltage for safety. Therefore, the part which is
replaced should be used the part which has
the same character.
Especially as to the important parts for safety
which is indicated in the circuit diagram or the
table of parts as a
mark, the designated
parts must be used.
4. PUT PARTS AND WIRES IN THE
ORIGINAL POSITION AFTER
ASSEMBLING OR WIRING
There are parts which use the insulation
material such as a tube or tape for safety, or
which are assembled in the condition that
these do not contact with the printed board.
The inside wiring is designed not to get closer
to the pyrogenic parts and high voltage parts.
Therefore, put these parts in the original
positions.
5. TAKE CARE TO DEAL WITH THE
CATHODE-RAY TUBE
In the condition that an explosion-proof cathoderay tube is set in this equipment, safety is
secured against implosion. However, when
removing it or serving from backward, it is
dangerous to give a shock. Take enough care to
deal with it.
Safety is secured against an X-ray by considering about the cathode-ray tube and the high
voltage peripheral circuit, etc.
Therefore, when repairing the high voltage peripheral circuit, use the designated parts and
make sure not modify the circuit.
Repairing except indicates causes rising of high
voltage, and it emits an X-ray from the cathoderay tube.
7. PERFORM A SAFETY CHECK AFTER
SERVICING
Confirm that the screws, parts and wiring which
were removed in order to service are put in the
original positions, or whether there are the
portions which are deteriorated around the
serviced places serviced or not. Check the
insulation between the antenna terminal or
external metal and the AC cord plug blades.
And be sure the safety of that.
(INSULATION CHECK PROCEDURE)
1. Unplug the plug from the AC outlet.
2. Remove the antenna terminal on TV and turn
on the TV.
3. Insulation resistance between the cord plug
terminals and the eternal exposure metal
[Note 2] should be more than 1M ohm by
using the 500V insulation resistance meter
[Note 1].
4. If the insulation resistance is less than 1M
ohm, the inspection repair should be
required.
[Note 1]
If you have not the 500V insulation
resistance meter, use a Tester.
[Note 2]
External exposure metal: Antenna terminal
Earphone jack
HOW TO ORDER PARTS
Please include the following informations when you order parts. (Particularly the VERSION LETTER.)
1. MODEL NUMBER and VERSION LETTER
The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be
found at the end of the SERIAL NUMBER.
2. PART NO. and DESCRIPTION
You can find it in your SERVICE MANUAL.
GENERAL SPECIFICATIONS
G-1
TV
System
CRT
CRT Size / Visual Size
CRT Type
Deflection
Magnetic Field
BV/BH
Video Head
20 inch
/ 508.0 mmV
Flat
90
degree
+ 0.45 G
/ 0.18 G
NTSC
2 Speaker
Front
3 Inch
8
ohm
1.5W + 1.5W
1.5W + 1.5W
VHS Player / Recorder
NTSC
Yes
No
OVD-6S
Front
3
4 Head
FM Audio Head
2 Head
Color System
Speaker
Position
Size
Impedance
MAX
10%(Typical)
Sound Output
G-2
VCR
System
System
Video System
Hi-Fi STEREO
NTSC PB
Deck
Heads
DECK
Loading System
Motor
Audio /Control
Erase(Full Track Erase)
Tape
Rec
PAL
Speed
NTSC
Play
PAL
NTSC
Fast Forward / Rewind Time (Approx.)
with Cassette
G-3
Tuning
System
Forward/Reverse
Picture Search
Frame Advance
Slow Speed
Broadcasting System
Tuner and
Receive CH
NTSC or PAL-M
System
Destination
Tuning System
Input Impedance
CH Coverage
Intermediate
Frequency
G-4
Signal
Preset CH
Stereo/Dual TV Sound
Tuner Sound Muting
Video Signal
Audio Signal
(0dB=0.775Vrms)
Hi-Fi Audio Signal
G-5
Power
Power Source
Power Consumption
Protector
G-6
Regulation
G-7
Temperature
G-8
Operating Humidity
Picture(FP)
Sound(FS)
FP-FS
Input Level
Output Level
S/N Ratio (Weighted)
Horizontal Resolution at SP Mode
Input Level
Output Level
S/N Ratio at SP (Weighted)
Harmonic Distortion (1KHz)
Frequency Response
at SP
at LP
at SLP
Dynamic Range : More than
Wow And Flutter : Less than
Channel Separation : More than
Harmonic Distortion : Less than
AC
DC
at AC
at DC
Stand by (at AC)
Per Year
Power Fuse
Dew Sensor
Safety
Radiation
X-Radiation
Operation
Storage
Mono
/Yes
Yes
SP/SLP(EP)
SP/SLP(EP)
FF:4'50"/REW:2'30"
T-120
SP/SLP(EP) = 3x,5x / 9x,15x
1/10
1/10
US System M
1 Tuner
US(w/CATV)
F-Synth
VHF/UHF 75 ohm
2~69, 4A,A-5~A-1, A~I,
J~W,W+1~W+84
45.75MHz
41.25MHz
4.5MHz
No
US-ST
Yes
1 V p-p/75 ohm
1 V p-p/75 ohm
50
220Line
-8dB/50Kohm
-8dB/1Kohm
38
1.5
%
100Hz - 10kHz
100Hz - 4kHz
90
dB
0.01
%Wrms
60
dB
1.0
%
120V,60Hz
115 W at 120 V 60 Hz
5 W at 120 V 60 Hz
Yes
No
UL
FCC
DHHS
+5oC ~ +40oC
-20oC ~ +60oC
Less then 80% RH
GENERAL SPECIFICATIONS
G-9
On Screen
Display
Menu
Menu
Timer Rec Set
Channel Setup
Yes
Character
Yes
Yes
Yes
Yes
Yes
Type
TV/CATV
Auto CH Memory
Add/ Delete
Guide CH Set
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes (Calendar 12h)
Yes
Yes
Yes
Yes
No
No
No
No
No
No
No
No
No
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
TV Setup
V-chip Set
On/Off Timer Set
Picture
Audio
Sap On/Off
Auto Repeat On/Off
System Setup
Clock Set
Language
Auto Clock On/Off
Standard Time
Daylight Saving Time
Commercial Advance
Marking On/Off
Blueback On/Off
Playback Auto/Manual
Unmarked Tape
Movie Advance
Go To Movie
Go To Preview
G-CODE(or SHOWVIEW or PLUSCODE)No. Entry
Clock / Date
CH/AV
Tape Counter(Linear Counter)
Tape Speed
Sleep Time
Stereo/Audio Output
Bilingal
SAP
Control
Volume
Level
Bright / Contrast / Sharpness / Color
Tint
Bass/Treble/Balance
Manual Tracking
Play/Stop/FF/Rew/Rec/OTR/T-Rec/Pause/Eject/Tape In
Mark)
Auto Tracking/Manual Tracking
Caption / Text
Index
Muting
Hi-Fi
Repeat
Zero Return
DEW
G-10
OSD Language
G-11
Clock,Timer
and Timer
Back-up
(Symbol
OSD Language Setting
Calendar
Timer Events
One Touch Recording Max Time
OTPB Valid Time
Sleep Timer
Max Time
Step
On/Off Timer
Program(On Timer / Off Timer)
Auto Shut Off
No Signal
No Operation
Timer Back-up (at Power Off Mode)
Yes
Yes
Yes
No
Yes
Yes
Yes
No
No
English French Spanish
English
1990/1/1 ~ 2081/12/31
8 Program/ 1 Month
5 Hours
No
120
Min
10
Min
1
Program
15 Min
No
5
Sec
GENERAL SPECIFICATIONS
G-12
Remote
Control
Unit
Glow in Dark Remocon
Format
Custom Code
Power Source
Total Keys
Keys
G-13
Features
Voltage(D.C)
UM size x pcs
Power
1
2
3
4
5
6
7
8
9
0
CH Up
CH Down
Volume Up
Volume Down
Input Select
Play
F.Fwd
Rew
Pause/Still
Stop
Rec/OTR
Eject
Counter Reset
Speed
Timer Rec
TV Monitor
Quick View
Program
Slow
Auto Tracking
Set/Tracking+
Set/ Tracking Menu
Enter
Cancel
Call
TV/Caption/Text
Sleep Timer
Muting
Zero Return
CM Skip
Audio Select
Auto Head Cleaning
Auto Tracking
HQ (VHS Standard High Quality)
Auto Power On, Auto Play, Auto Rewind, Auto Eject
VIDEO PLUS+(SHOWVIEW,G-CODE)
Auto Clock
Forward / Reverse Picture Search
Reverse Slow
One Touch Playback
Auto CH Memory
Closed Caption
TV Auto Shut off Function
End Call
Index Search
SQPB
CATV
CM Skip(30sec x 6 Times)
Comb Filter
TV Monitor
Program Extend
Choke Coil
Energy Star
Protect of FBT Leak Curcuit
Dirty Head
V-chip
USA V-chip
CANADA V-chip
CM Advance
Movie Advance
RC-DQ
Yes
NEC
40-BFh,44-BBh
3V
UM-4 x 2 pcs
44
Keys
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes(2Keys)
Yes
Yes
Yes
Yes(2Keys)
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
No
No
Yes
Yes
Yes
No
No
No
Yes
Yes
Yes
No
No
No
Yes
Yes
No
Yes
No
No
No
GENERAL SPECIFICATIONS
G-14
Accessories
Owner's Manual
Language
w/Guarantee Card
Remote Control Unit
Battery
UM size x pcs
English
Yes
Yes
Yes
UM-4 x 2 pcs
No
No
Rod Antenna
Poles
Terminal
-
Terminal
-
Loop Antenna
G-15
Interface
G-16
G-17
Set Size
Weight
G-18
Carton
No
U/V Mixer
300 ohm to 75 ohm Antenna Adapter
Antenna Change Plug
DC Car Cord (Center+)
AC Plug Adapter
AC Cord
AV Cord (2Pin-1Pin)
Guarantee Card
Registration Card
ESP Card
Warning Sheet
Dew/AHC Caution Sheet
Quick Set-up Sheet
Circuit Diagram
Service Facility List
Important Safeguard
Switch
Power
Play
Pause/Still
System Select
One Touch Playback
Channel Up
Channel Down
F.FWD/Cue
Eject/Stop
Main Power SW
Volume Up
Volume Down
Rew/Rev
Rec/OTR
Input Select
Indicator
Power
Rec/OTR
T-Rec
On Timer
CS
Key Light up
Rec/OTR
One Touch Playback
Play
Terminals
Front
Video Input
Audio Input
Other Terminal
Rear
Video Input
Audio Input
Video Output
Audio Output
Euro Scart
Diversity
Ext Speaker
DC Jack 12V(Center +)
VHF/UHF Antenna Input
AC Inlet
Approx.
W x D x H (mm)
Net (Approx.)
Gross (Approx.)
Master Carton
Content
Material
Dimensions
W x D x H(mm)
Description of Origin
Gift Box
Material
Dimensions
W x D x H(mm)
Design
Description of Origin
Drop Test
Natural Dropping At
Height (cm)
Container Stuffing(40' container)
No
Yes
No
No
No
No
No
No
Yes
Yes
No
No
No
No
No
No
Yes
Yes
No
No
No
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
No
Red
Red
Red
No
No
No
No
No
RCAx1
RCA x 2(Stereo)
Head Phone(Stereo & Mono, 3.5mm)
RCAx1
RCA x 2(Stereo)
RCAx1
RCA x 2(Stereo)
No
No
No
No
F Type
No
574 x 483 x 514.5
26.5 kg( 58.5 lbs)
28.5 kg( 62.9 lbs)
No
Yes
DOUBLE/WHITE
647 x 627 x 625
As per Buyer's
Yes
1 Corner / 3 Edges / 6 Surfaces
31
171
Sets
GENERAL SPECIFICATIONS
G-19
Cabinet Material
Cabinet Front
Cabinet Rear
Jack Panel
PS 94V0
PS 94V0
PS 94V0
DECABROM
DECABROM
DISASSEMBLY INSTRUCTIONS
1. REMOVAL OF MECHANICAL PARTS
AND P.C. BOARDS
1-1: BACK CABINET (Refer to Fig. 1-1)
1. Remove the 6 screws 1.
2. Remove the 2 screws 2 which are used for holding the
Back Cabinet.
3. Remove the AC cord from the AC cord hook 3.
4. Remove the Back Cabinet in the direction of arrow.
1-3: TV/VCR BLOCK (Refer to Fig. 1-3)
1. Remove the 2 screws 1.
2. Disconnect the following connectors:
(CP401, CP502, CP4201 and CP4202).
3. Unlock the support 2.
4. Remove the TV/VCR Block in the direction of arrow.
1
Front Cabinet
Front Cabinet
1
1
2
UP TO
RELEASE
1
1
TV/VCR Block
1
Fig. 1-3
1
2
2
3
1-4: MAIN PCB (Refer to Fig. 1-4)
Back Cabinet
1
Fig. 1-1
1-2: CRT PCB (Refer to Fig. 1-2)
CAUTION: BEFORE REMOVING THE ANODE CAP,
DISCHARGE ELECTRICITY BECAUSE IT
CONTAINS HIGH VOLTAGE.
BEFORE ATTEMPTING TO REMOVE OR
REPAIR ANY PCB, UNPLUG THE POWER
CORD FROM THE AC SOURCE.
1. Remove the Anode Cap.
(Refer to REMOVAL OF ANODE CAP)
2. Disconnect the following connectors:
(CP801, CP802 and CP805).
3. Remove the CRT PCB in the direction of arrow.
Front Cabinet
1. Remove the screw 1.
2. Remove the Main PCB Holder.
3. Remove the 2 screws 2.
4. Remove the 3 screws 3.
5. Disconnect the following connectors:
(CP810A, CP820A and CP402).
6. Remove the Main PCB in the direction of arrow.
2
2
3
Main PCB
3
3
Main PCB Holder
1
CRT PCB
VCR Block
Fig. 1-4
Fig. 1-2
DISASSEMBLY INSTRUCTIONS
1-5: DECK SHIELD PLATE (Refer to Fig. 1-5)
1-7: JACK PLATE AND SYSCON PCB (Refer to Fig. 1-7)
1. Remove the 2 screws 1.
2. Remove the screw 2.
3. Remove the Deck Shield Plate in the direction of arrow.
1. Remove the screw 1.
2. Remove the Syscon PCB in the direction of arrow (A).
3. Remove the 2 screws 2.
4. Unlock the 2 supports 3.
5. Remove the Jack Plate in the direction of arrow (B).
Deck Shield Plate
2
Jack Plate
1
2
2
3
1
Syscon PCB
(B)
3
1
(A)
VCR Block
Fig. 1-5
1-6: DECK CHASSIS (Refer to Fig. 1-6)
1. Remove the 3 screws 1.
2. Disconnect the following connectors:
(CP1004, CP1005, CP1006, CP4001, CP4002 and
CP4003).
3. Remove the Deck Chassis in the direction of arrow.
1
1
1
Deck Chassis
Syscon PCB
Fig. 1-6
Deck Holder
Fig. 1-7
DISASSEMBLY INSTRUCTIONS
2. REMOVAL OF DECK PARTS
NOTE
2-1: TOP BRACKET (Refer to Fig. 2-1)
When you install the Tape Guide L, install as shown in the
circle of Fig. 2-3-B. (Refer to Fig. 2-3-B)
1. Remove the 2 screws 1.
2. Slide the 2 supports 2 and remove the Top Bracket.
NOTE
Tape Guide L
When you install the Top Bracket, install the screw (1)
first, then install the screw (2).
REC Lever
(2)
(1)
1
1
Top Bracket
Top Bracket
• The REC Lever is not installed on the Video Cassette Player.
Fig. 2-3-B
2-4: CASSETTE HOLDER ASS'Y (Refer to Fig. 2-4)
2
2
Main Chassis
Main Chassis
• Screw Torque: 5 ± 0.5kgf•cm
Fig. 2-1
2-2: FLAP LEVER/TAPE GUIDE R (Refer to Fig. 2-2)
1. Move the Cassette Holder Ass'y to the front side so that
the Link Ass'y doesn't slip out.
2. Push the Locker R to remove the Cassette Side R.
3. Remove the Cassette Side L.
Cassette Side R
Locker R
Main Chassis
1. Move the Cassette Holder Ass'y to the back side.
2. Remove the Polyslider Washer 1.
3. Remove the Flap Lever.
4. Unlock the 3 supports 2 and remove the Tape Guide R.
Tape Guide R
Flap Lever
Main Chassis
Cassette Side L
Fig. 2-4
2
2 2
2-5: CASSETTE SIDE L/R (Refer to Fig. 2-5)
1
Main Chassis
Fig. 2-2
1. Unlock the 4 supports 1 and then remove the Cassette
Side L/R.
2. Remove the Cassette Earth Spring.
NOTE
2-3: TAPE GUIDE L (Refer to Fig. 2-3-A)
1. Move the Cassette Holder Ass'y to the back side.
2. Unlock the 2 supports 1 and remove the Tape Guide L.
3. Remove the REC Lever. (Recorder only)
REC Lever
1. When you install the Cassette Side R, be sure to move
the Locker R after installing.
2. After the installation of the Cassette Holder, then install
the Cassette Earth Spring.
1
Cassette Holder
1
Tape Guide L
Locker R
1
1
1
Cassette Side R
Cassette Side L
1
Main Chassis
• The REC Lever is not installed on the Video Cassette Player.
Fig. 2-3-A
Cassette Earth Spring
Fig. 2-5
DISASSEMBLY INSTRUCTIONS
2-6: LINK UNIT (Refer to Fig. 2-6)
2-9: TENSION ASS'Y (Refer to Fig. 2-9-B)
1. Set the Link Unit to the Eject position.
2. Remove the (A) side of the Link Unit first, then remove
the (B) side.
1. Turn the Middle Gear clockwise so that the Tension
Holder hook, is set to the position of Fig. 2-9-A to more
the Tension Arm Ass'y.
2. Remove the Tension Spring.
3. Unlock the support 1 and remove the Tension Arm
Ass'y.
4. Remove the Tension Adjust.
5. Unlock the 2 supports 2 and remove the Tension Band
Ass'y.
6. Float the hook 3 and turn it clockwise then remove the
Tension Holder.
7. Remove the SS Brake Spring.
8. Remove the SS Arm Brake.
Link Unit
(B)
Link Unit
(A)
Main Chassis
Main Chassis
Tension Arm Ass'y
Fig. 2-6
2-7: LOADING MOTOR ASS'Y (Refer to Fig. 2-7)
1. Remove the Link Lever.
2. Remove the screw 1.
3. Remove the Loading Motor Ass'y.
4. Unlock the 2 supports 2 and remove the Deck PCB
(BOT).
Fig. 2-9-A
Tension Adjust
2
2
Tension Band Ass'y
Loading Motor Ass'y
Tension Spring
Tension Arm Ass'y
1
3
2
Tension Holder
SS Brake Spring
Main Chassis
SS Arm Brake
1
Deck PCB
(BOT)
Inclined S Ass'y
Link Lever
Fig. 2-9-B
• Screw Torque: 5 ± 0.5kgf•cm
Fig. 2-7
NOTE
When you install the Tension Adjust, install as shown in
Fig. 2-9-C. (Refer to Fig. 2-9-C)
2-8: SENSOR COVER L3 (Refer to Fig. 2-8)
1. Unlock the support 1 and remove the Sensor Cover L3.
Adjust the direction of the Marker to inside.
Main Chassis
Fig. 2-9-C
Sensor Cover L3
1
Fig. 2-8
DISASSEMBLY INSTRUCTIONS
2-10: T BRAKE ASS'Y (Refer to Fig. 2-10)
1
1. Remove the T Brake Spring.
2. Turn the T Brake Ass'y clockwise and bend the hook
section to remove it.
P5 Spring
2
Cassette Opener
2
P5-3 Arm Ass'y
T Brake Ass'y
Pinch Roller Block
Pinch Roller Arm Spring
Pinch Roller Lever Ass'y
Hook section
T Brake Spring
Main Chassis
• Screw Torque: 5 ± 0.5kgf•cm
Fig. 2-10
Fig. 2-12-A
NOTE
1. Do not touch the Pinch Roller. (Use gloves.)
2. When you install the Pinch Roller Block, install as shown
in the circle of Fig. 2-12-B. (Refer to Fig. 2-12-B)
2-11: S REEL/T REEL (Refer to Fig. 2-11)
1. Remove the S Reel and T Reel.
2. Remove the 2 Polyslider Washers 1.
NOTE
1. Take care not to damage the gears of the S Reel and T
Reel.
2. The Polyslider Washer may be remained on the back of
the reel.
3. Take care not to damage the shaft.
4. Do not touch the section "A" of S Reel and T Reel. (Use
gloves.) (Refer to Fig. 2-11) Do not adhere the stains
on it.
5. When you install the reel, clean the shaft and oil it. (If
you do not oil, noise may be heard in FF/REW mode.)
6. After installing the reel, adjust the height of the reel.
(Refer to MECHANICAL ADJUSTMENT)
S Reel
Fig. 2-12-B
2-13: A/C HEAD (Refer to Fig. 2-13-A)
1. Remove the screw 1.
2. Remove the A/C Head Base.
3. Remove the 3 screws 2.
4. Remove the A/C Head and A/C Head Spring.
NOTE
1. Do not touch the A/C Head. (Use gloves.)
2. When you install the A/C Head Spring, install as shown
in Fig. 2-13-B. (Refer to Fig. 2-13-B)
3. When you install the A/C Head, tighten the screw (1)
first, then tighten the screw (2), finally tighten the screw
(3).
(A)
1
T Reel
(A)
1
(1)
2
Fig. 2-11
(3)
2
2
(2)
A/C Head
2-12: PINCH ROLLER BLOCK/P5-3 ARM ASS'Y
(Refer to Fig. 2-12-A)
A/C Head Spring
1. Remove the P5 Spring.
2. Remove the screw 1.
3. Unlock the 2 supports 2 and remove the Cassette
Opener.
4. Remove the Pinch Roller Block, Pinch Roller Arm
Spring, Pinch Roller Lever Ass'y and P5-3 Arm Ass'y.
1
A/C Head Base
• Screw Torque: 5 ± 0.5kgf•cm (Screw 1)
Fig. 2-13-A
DISASSEMBLY INSTRUCTIONS
2-16: CAPSTAN DD UNIT (Refer to Fig. 2-16)
1. Remove the Capstan Belt.
2. Remove the 3 screws 1.
3. Remove the Capstan DD Unit.
Spring Position
Fig. 2-13-B
Capstan Belt
Capstan DD Unit
2-14: FE HEAD (RECORDER ONLY) (Refer to Fig. 2-14)
1. Remove the screw 1.
2. Remove the FE Head.
1
FE Head
1
1
1
• Screw Torque: 5 ± 0.5kgf•cm
• The FE Head is not installed on the Video Cassette Player.
• Screw Torque: 4 ± 0.5kgf•cm
Fig. 2-14
Fig. 2-16
2-17: MIDDLE GEAR/MAIN CAM (Refer to Fig. 2-17-A)
1. Remove the Polyslider Washer 1, then remove the
Middle Gear.
2. Remove the E-Ring, then remove the Main Cam, P5
Cam, Pinch Roller Cam and Joint Gear.
2-15: AHC ASS'Y/CYLINDER UNIT ASS'Y
(Refer to Fig. 2-15)
1. Unlock the support 1 and remove the AHC Ass'y.
2. Remove the 3 screws 2.
3. Remove the Cylinder Unit Ass'y.
1
Middle Gear
NOTE
E-Ring
When you install the Cylinder Unit Ass'y, tighten the
screws from (1) to (3) in order while pulling the Ass'y
toward the left front direction.
Main Cam
Pinch Roller Cam
Joint Gear
P5 Cam
AHC Ass'y
1
Cylinder Unit Ass'y
Fig. 2-17-A
NOTE
When you install the Pinch Roller Cam, P5 Cam and Main
Cam, align each marker. (Refer to Fig. 2-17-B)
Pinch Roller Cam
2 (1)
(2) 2
• Screw Torque: 3 ± 0.5kgf•cm
2
Check the hole of Main
Chassis can be seen.
(3)
P5 Cam
Fig. 2-15
Marker
Main Cam
Fig. 2-17-B
DISASSEMBLY INSTRUCTIONS
2-18: CLUTCH ASS'Y (Refer to Fig. 2-18)
NOTES
1. Remove the Capstan Brake Spring.
2. Remove the Polyslider Washer 1.
3. Remove the Clutch Ass'y, Ring Spring and Coupling
Gear.
4. Unlock the 2 supports 2 and remove the Clutch Lever.
1. When you install the Loading Arm S Ass'y, Loading Arm
T Ass'y and Main Loading Gear, align each marker.
(Refer to Fig. 2-19-B)
Marker
1
Main Loading Gear
Clutch Ass'y
Marker
Capstan Brake Spring
Ring Spring
Coupling Gear
Clutch Lever
2
Loading Arm T Ass'y
Loading Arm S Ass'y
2
Fig. 2-18
Fig. 2-19-B
2-19: LOADING GEAR S/T ASS'Y (Refer to Fig. 2-19-A)
2. When you install the Clutch Actuator, install as shown in
the circle of Fig. 2-19-C. (Refer to Fig. 2-19-C)
1. Remove the E-Ring 1 and remove the Main Loading
Gear.
2. Slide the Main Rod and remove the Spring Holder.
3. Remove the Main Rod, Tension Lever, Clutch Actuator,
Idler Arm Ass'y.
4. Remove the screw 2.
5. Remove the LED Reflecter.
6. Remove the Loading Arm S Ass'y and Loading Arm T
Ass'y.
7. Remove the Loading Gear S and Loading Gear T.
8. Remove the Loading Gear Spring.
Spring Holder
1
Main Loading Gear
Main Rod
Clutch Actuator
Fig. 2-19-C
2-20: INCLINED S/T ASS'Y (Refer to Fig. 2-20)
1. Remove the Cap P4.
2. Remove the screw 1.
3. Unlock the support 2 and remove the Loading Gear
Holder.
4. Remove the Inclined S Unit.
5. Remove the Inclined T Unit.
NOTE
Tension Lever
Loading Gear T
Do not touch the roller of Guide Roller.
Idler Arm Ass'y
1
LED Reflecter
2
Loading Gear
Spring
Loading Gear Holder
Loading Arm T Ass'y
Inclined S Unit
2
Loading Gear S
Clutch Actuator
Loading Gear
Spring
Inclined T Unit
Cap P4
Loading Arm S Ass'y
• Screw Torque: 5 ± 0.5kgf•cm
Fig. 2-19-A
• Screw Torque: 2.5 ± 0.5kgf•cm
Fig. 2-20
DISASSEMBLY INSTRUCTIONS
3. After one side is removed, pull in the opposite direction
to remove the other.
3. REMOVAL OF ANODE CAP
Read the following NOTED items before starting work.
* After turning the power off there might still be a potential
voltage that is very dangerous. When removing the
Anode Cap, make sure to discharge the Anode Cap's
potential voltage.
* Do not use pliers to loosen or tighten the Anode Cap
terminal, this may cause the spring to be damaged.
REMOVAL
1. Follow the steps as follows to discharge the Anode Cap.
(Refer to Fig. 3-1.)
Connect one end of an Alligator Clip to the metal part of a
flat-blade screwdriver and the other end to ground.
While holding the plastic part of the insulated Screwdriver,
touch the support of the Anode with the tip of the
Screwdriver.
A cracking noise will be heard as the voltage is discharged.
NOTE
Take care not to damage the Rubber Cap.
INSTALLATION
1. Clean the spot where the cap was located with a small
amount of alcohol. (Refer to Fig. 3-3.)
NOTE
Confirm that there is no dirt, dust, etc. at the spot where
the cap was located.
Location of Anode Cap
GND on the CRT
Fig. 3-3
2. Arrange the wire of the Anode Cap and make sure the
wire is not twisted.
3. Turn over the Rubber Cap. (Refer to Fig. 3-4.)
CRT
Screwdriver
Support
Alligator Clip
GND on the CRT
Fig. 3-4
Fig. 3-1
2. Flip up the sides of the Rubber Cap in the direction of
the arrow and remove one side of the support.
(Refer to Fig. 3-2.)
4. Insert one end of the Anode Support into the anode
button, then the other as shown in Fig. 3-5.
Rubber Cap
CRT
CRT
Support
Fig. 3-2
Support
Fig. 3-5
5. Confirm that the Support is securely connected.
6. Put on the Rubber Cap without moving any parts.
DISASSEMBLY INSTRUCTIONS
4. REMOVAL AND INSTALLATION OF
FLAT PACKAGE IC
REMOVAL
3. When IC starts moving back and forth easily after
desoldering completely, pickup the corner of the IC using
a tweezers and remove the IC by moving with the IC
desoldering machine. (Refer to Fig. 4-3.)
NOTE
1. Put the Masking Tape (cotton tape) around the Flat
Package IC to protect other parts from any damage.
(Refer to Fig. 4-1.)
Some ICs on the PCB are affixed with glue, so be
careful not to break or damage the foil of each IC
leads or solder lands under the IC when removing it.
NOTE
Masking is carried out on all the parts located within
10 mm distance from IC leads.
Masking Tape
(Cotton Tape)
Blower type IC
desoldering
machine
IC
Tweezers
Fig. 4-1
IC
Fig. 4-3
2. Heat the IC leads using a blower type IC desoldering
machine. (Refer to Fig. 4-2.)
4. Peel off the Masking Tape.
NOTE
Do not add the rotating and the back and forth
directions force on the IC, until IC can move back and
forth easily after desoldering the IC leads completely.
5. Absorb the solder left on the pattern using the Braided
Shield Wire. (Refer to Fig. 4-4.)
NOTE
Do not move the Braided Shield Wire in the vertical
direction towards the IC pattern.
Blower type IC
desoldering machine
Braided Shield Wire
Soldering Iron
IC
Fig. 4-2
IC pattern
Fig. 4-4
DISASSEMBLY INSTRUCTIONS
INSTALLATION
1. Take care of the polarity of new IC and then install the
new IC fitting on the printed circuit pattern. Then solder
each lead on the diagonal positions of IC temporarily.
(Refer to Fig. 4-5.)
4. When bridge-soldering between terminals and/or the
soldering amount are not enough, resolder using a Thintip Soldering Iron. (Refer to Fig. 4-8.)
Thin-tip Soldering Iron
IC
Soldering Iron
Fig. 4-8
Solder temporarily
Solder temporarily
Fig. 4-5
2. Supply the solder from the upper position of IC leads
sliding to the lower position of the IC leads.
(Refer to Fig. 4-6.)
Solder
IC
Soldering Iron
Supply soldering
from upper position
to lower position
Fig. 4-6
3. Absorb the solder left on the lead using the Braided
Shield Wire. (Refer to Fig. 4-7.)
NOTE
Do not absorb the solder to excess.
Soldering Iron
IC
Braided Shield Wire
Fig. 4-7
5. Finally, confirm the soldering status on four sides of the
IC using a magnifying glass.
Confirm that no abnormality is found on the soldering
position and installation position of the parts around the
IC. If some abnormality is found, correct by resoldering.
NOTE
When the IC leads are bent during soldering and/or
repairing, do not repair the bending of leads. If the
bending of leads are repaired, the pattern may be
damaged. So, be always sure to replace the IC in this
case.
KEY TO ABBREVIATIONS
A A/C
ACC
AE
AFC
AFT
AFT DET
AGC
AMP
ANT
A.PB
APC
ASS'Y
AT
AUTO
A/V
B BGP
BOT
BPF
BRAKE SOL
BUFF
B/W
C C
CASE
CAP
CARR
CH
CLK
CLOCK (SY-SE)
COMB
CONV
CPM
CTL
CYL
CYL-M
CYL SENS
D DATA (SY-CE)
dB
DC
DD Unit
DEMOD
DET
DEV
E E
EF
EMPH
ENC
ENV
EOT
EQ
EXT
F F
FBC
FE
FF
FG
FL SW
FM
FSC
FWD
G GEN
GND
H H.P.F
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Audio/Control
Automatic Color Control
Audio Erase
Automatic Frequency Control
Automatic Fine Tuning
Automatic Fine Tuning Detect
Automatic Gain Control
Amplifier
Antenna
Audio Playback
Automatic Phase Control
Assembly
All Time
Automatic
Audio/Video
Burst Gate Pulse
Beginning of Tape
Bandpass Filter
Brake Solenoid
Buffer
Black and White
Capacitance, Collector
Cassette
Capstan
Carrier
Channel
Clock
Clock (Syscon to Servo)
Combination, Comb Filter
Converter
Capstan Motor
Control
Cylinder
Cylinder-Motor
Cylinder-Sensor
Data (Syscon to Servo)
Decibel
Direct Current
Direct Drive Motor Unit
Demodulator
Detector
Deviation
Emitter
Emitter Follower
Emphasis
Encoder
Envelope
End of Tape
Equalizer
External
Fuse
Feed Back Clamp
Full Erase
Fast Forward, Flipflop
Frequency Generator
Front Loading Switch
Frequency Modulation
Frequency Sub Carrier
Forward
Generator
Ground
High Pass Filter
I
K
L
M
N
O
P
R
S
H.SW
Hz
IC
IF
IND
INV
KIL
L
LED
LIMIT AMP
LM, LDM
LP
L.P.F
LUMI.
M
MAX
MINI
MIX
MM
MOD
MPX
MS SW
NC
NR
OSC
OPE
PB
PB CTL
PB-C
PB-Y
PCB
P. CON
PD
PG
P-P
R
REC
REC-C
REC-Y
REEL BRK
REEL S
REF
REG
REW
REV, RVS
RF
RMC
RY
S. CLK
S. COM
S. DATA
SEG
SEL
SENS
SER
SI
SIF
SO
SOL
SP
STB
SW
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Head Switch
Hertz
Integrated Circuit
Intermediate Frequency
Indicator
Inverter
Killer
Left
Light Emitting Diode
Limiter Amplifier
Loading Motor
Long Play
Low Pass Filter
Luminance
Motor
Maximum
Minimum
Mixer, mixing
Monostable Multivibrator
Modulator, Modulation
Multiplexer, Multiplex
Mecha State Switch
Non Connection
Noise Reduction
Oscillator
Operation
Playback
Playback Control
Playback-Chrominance
Playback-Luminance
Printed Circuit Board
Power Control
Phase Detector
Pulse Generator
Peak-to Peak
Right
Recording
Recording-Chrominance
Recording-Luminance
Reel Brake
Reel Sensor
Reference
Regulated, Regulator
Rewind
Reverse
Radio Frequency
Remote Control
Relay
Serial Clock
Sensor Common
Serial Data
Segment
Select, Selector
Sensor
Search Mode
Serial Input
Sound Intermediate Frequency
Serial Output
Solenoid
Standard Play
Serial Strobe
Switch
KEY TO ABBREVIATIONS
S SYNC
SYNC SEP
T TR
TRAC
TRICK PB
TP
U UNREG
V V
VCO
VIF
VP
V.PB
VR
V.REC
VSF
VSR
VSS
V-SYNC
VT
X X'TAL
Y Y/C
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Synchronization
Sync Separator, Separation
Transistor
Tracking
Trick Playback
Test Point
Unregulated
Volt
Voltage Controlled Oscillator
Video Intermediate Frequency
Vertical Pulse, Voltage Display
Video Playback
Variable Resistor
Video Recording
Visual Search Fast Forward
Visual Search Rewind
Voltage Super Source
Vertical-Synchronization
Voltage Tuning
Crystal
Luminance/Chrominance
SERVICE MODE LIST
This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily.
To enter SERVICE MODE, unplug AC cord till lost actual clock time. Then press and hold Vol (-) button of main unit and
remocon key simultaneously.
The both pressing of set key and remote control key will not be possible if clock has been set. To reset clock, either unplug
AC cord and allow at least 5 seconds before Power On.
Set Key
Remocon Key
VOL. (-) MIN
0
Releasing of V-CHIP PASSWORD.
VOL. (-) MIN
1
Initialization of the factory.
NOTE: Do not use this for the normal servicing.
VOL. (-) MIN
2
Horizontal position adjustment of OSD.
NOTE: Also can be adjusted by using the Adjustment MENU.
Refer to the "ELECTRICAL ADJUSTMENT" (OSD HORIZONTAL).
VOL. (-) MIN
3
Adjust the PG SHIFTER automatically.
Refer to the "ELECTRICAL ADJUSTMENT" (PG SHIFTER).
VOL. (-) MIN
4
Adjust the PG SHIFTER manually.
Refer to the "ELECTRICAL ADJUSTMENT" (PG SHIFTER).
VOL. (-) MIN
5
Adjusting of the Tracking to the center position.
NOTE: Also can be adjusted by pressing the ATR button for more than 2 seconds
during PLAY.
VOL. (-) MIN
6
Operations
POWER ON total hours and PLAY/REC total hours are displayed on the screen.
Refer to the "PREVENTIVE CHECKS AND SERVICE INTERVALS" (CONFIRMATION
OF USING HOURS).
Can be checked of the INITIAL DATA of MEMORY IC.
Refer to the "NOTE FOR THE REPLACING OF MEMORY IC".
VOL. (-) MIN
8
Writing of EEPROM initial data.
NOTE: Do not use this for the normal servicing.
VOL. (-) MIN
9
Display of the Adjustment MENU on the screen.
Refer to the "ELECTRICAL ADJUSTMENT" (On-Screen Display Adjustment).
Method
Press the ATR button on the
remote control for more than
2 seconds during PLAY.
Make the short circuit between
the test point of SERVICE and
the GND.
Operations
Adjusting of the Tracking to the center position.
Refer to the "MECHANICAL ADJUSTMENT" (GUIDE ROLLER) and "ELECTRICAL
ADJUSTMENT" (PG SHIFTER).
The EOT/BOT/Reel sensor do not work at this moment.
Refer to the "PREPARATION FOR SERVICING"
PREVENTIVE CHECKS AND SERVICE INTERVALS
The following standard table depends on environmental conditions and usage. Unless maintenance is properly
carried out, the following service intervals may be quite shortened as harmful effects may be had on other parts.
Also, long term storage or misuse may cause transformation and aging of rubber parts.
Time
Parts Name
500
hours
1,000
hours
1,500
hours
2,000
hours
3,000
hours
Notes
Audio Control Head
Clean those parts in
contact with the tape.
Full Erase Head
(Recorder only)
Capstan Belt
Clean the rubber, and parts
which the rubber touches.
Pinch Roller
Capstan DD Unit
Loading Motor
Tension Band
Capstan Shaft
Tape Running
Guide Post
Replace when rolling
becomes abnormal.
Cylinder Unit
Clean the Head
: Clean
: Replace
CONFIRMATION OF USING HOURS
POWER ON total hours and PLAY/REC total hours can be checked on the screen.
Total hours are displayed in 16 system of notation.
NOTE: The confirmation of using hours will not be possible if clock has been set. To reset clock, either unplug
AC cord and allow at least 5 seconds before Power On.
1. Set the VOLUME to minimum.
2. While holding down VOLUME button on front cabinet, press key 6 on remote control simultaneously.
3. After the confirmation of using hours, turn off the power.
INIT
00
83
POWER ON 0010
PLAY/REC 0003
Initial setting content of MEMORY IC.
POWER ON total hours.
PLAY/REC total hours.
(16 x 16 x 16 x thousands digit value) + (16 x 16 x hundreds digit value) + (16 x tens digit value) + (ones digit value)
PREVENTIVE CHECKS AND SERVICE INTERVALS
CLEANING
NOTE
2. TAPE RUNNING SYSTEM
After cleaning the heads with isopropyl alcohol, do not
run a tape until the heads dry completely. If the heads
are not completely dry and alcohol gets on the tape,
damage may occur.
1. AUDIO CONTROL HEAD
Clean the Audio Control Head with the cotton stick
soaked by alcohol. Clean the full erase head in the
same manner. (Refer to the figure below.)
When cleaning the tape transport system, use the
gauze moistened with isopropyl alcohol.
3. CYLINDER
Wrap a piece of chamois around your finger. Dip it in
isopropyl alcohol. Hold it to the cylinder head softly.
Turn the cylinder head counterclockwise to clean it (in
the direction of the arrow). (Refer to the figure below.)
NOTE
Do not exert force against the cylinder head. Do not move
the chamois upward or downward on the head.
Use the chamois one by one.
Head
Head
Audio Control Head
Cylinder Head
NOTE FOR THE REPLACING OF MEMORY IC
If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to
ensure correct data settings while making reference to TABLE 1.
NOTE: Initial Data setting will not be possible if clock has been set. To reset clock, either unplug AC cord and allow
at least 5 seconds before Power On.
INI
+0
+1
+2
+3
+4
+5
+6
+7
+8
+9
+A
+B
+C
+D
+E
+F
00
88
1B
82
67
C3
15
34
0B
51
9A
3C
96
19
4F
28
1A
10
BD
A4
9C
94
0C
00
30
05
08
00
A9
54
04
3E
14
00
20
06
3A
01
15
10
60
32
3A
D5
D2
62
24
66
08
28
68
30
29
69
2A
6A
6B
6C
6D
6E
6F
50
70
70
71
71
52
52
40
72
72
53
73
54
74
74
55
55
75
75
56
56
56
76
76
50
57
57
77
77
58
58
78
78
59
59
79
79
5A
5A
7A
7A
60
5B
5B
5C
5C
5D
5D
5E
5E
7E
7E
---
---
---
---
---
---
Table 1
1. Enter DATA SET mode by setting VOLUME to minimum.
2. While holding down VOLUME button on front cabinet, press key 6 on remote control simultaneously.
ADDRESS and DATA should appear as FIG 1.
ADDRESS
INIT
00
DATA
83
POWER ON 0010
PLAY/REC 0003
Fig. 1
3. ADDRESS is now selected and should "blink". Using the SET + or - keys on the remote, step through the ADDRESS until
required ADDRESS to be changed is reached.
4. Press ENTER to select DATA. When DATA is selected, it will "blink".
5. Again, step through the DATA using SET + or - until required DATA value has been selected.
6. Pressing ENTER will take you back to ADDRESS for further selection if necessary.
7. Repeat steps 3 to 6 until all data has been checked.
8. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.
The unit will now have the correct DATA for the new MEMORY IC.
SERVICING FIXTURES AND TOOLS
Alignment Tape
Back tension cassette gauge
Torque cassette gauge
(KT-300NR)
Taper nut driver
ST-N5
ST-NF
70909103
70909199
70909228
VTR cleaning kit
VTR lubrication kit
Grease
JG002B Adapter
JG002E Dial Torque Gauge
(10~90gf•cm)
JG002F (60~600gf•cm)
JG022 Master Plane
JG024A Reel Disk Height
Adjustment Jig
JG153 X Value Adjustment
Screwdriver
JG154 Cable
JG162B Cable (9 Pins)
JG162F Cable (13 Pins)
JG162Y Cable (5 Pins)
Tentelometer
Ref. No.
Part No.
Parts Name
JG002B
APJG002B00
Adapter
VSR Torque, Brake Torque (S Reel/T Reel Ass'y)
JG002E
APJG002E00
Dial Torque Gauge (10~90gf•cm)
Brake Torque (T Reel Ass'y)
JG002F
APJG002F00
Dial Torque Gauge (60~600gf•cm)
VSR Torque, Brake Torque (S Reel)
JG022
APJG022000
Master Plane
Reel Disk Height Adjustment
JG024A
APJG024A00
Reel Disk Height Adjustment Jig
Reel Disk Height Adjustment
JG153
APJG153000
X Value Adjustment Screwdriver
X Value Adjustment
JG154
APJG154000
Cable
Used to connect the test point of SERVICE and GROUND
JG162B
APJG162B00
Cable
Used to connect the Syscon PCB and Main PCB
JG162F
APJG162F00
Cable
Used to connect the Syscon PCB and Main PCB
JG162Y
APJG162Y00
Cable
Used to connect the Syscon PCB and CRT PCB
Remarks
PREPARATION FOR SERVICING
How to use the Servicing Fixture
1. Unplug the connector CP4201 and CP4202, then remove the TV/VCR Block from the set.
2. Unplug the connector CP810A, CP820A and CP805, then remove the Main PCB from the VCR Block.
3. Connect as shown in the below figure using the Service Fixture.
• Connect the Syscon PCB to the Main PCB with the cable JG162B and JG162F.
• Connect the Syscon PCB to the CRT PCB with the cable JG162Y.
4. Remove the Operation PCB from the set, then connect it with the Syscon PCB.
If necessary, connect CD702 (Front A/V Jack Input Terminal)
5. Short circuit between TP1001 and Ground with the cable JG154.
(Refer to MAJOR COMPONENTS LOCATION GUIDE)
The EOT, BOT and Reel Sensor do not work at this moment.
6. At that time, the STOP/EJECT button is available to insert and eject the Cassette Tape.
Front Cabinet
CRT PCB
CP820A
CP805
Main PCB
CP810A
JG162Y
JG162F
CP850B
JG162B
CP820B
Syscon PCB
CD810B
JG154
TP1001
CP4201
To Ground
CD757
Operation PCB
CD702
MECHANICAL ADJUSTMENTS
1. CONFIRMATION AND ADJUSTMENT
Read the following NOTES before starting work.
• Place an object which weighs between 450g~500g on
the Cassette Tape to keep it steady when you want to
make the tape run without the Cassette Holder. (Do not
place an object which weighs over 500g.)
• When you activate the deck without the Cassette Holder,
short circuit between TP1001 and GND. (Refer to
ELECTRICAL ADJUSTMENT PARTS LOCATION
GUIDE) In this condition the BOT/EOT/Reel Sensor will
not function.
1-2: CONFIRMATION AND ADJUSTMENT OF TENSION
POST POSITION
1. Set to the PLAY mode.
2. Adjust the Tension Adjust until the edge of the Tension
Arm is positioning within 0.5mm range from the
standard line center of Main Chassis.
After this adjustment, confirm that the cut position is
located in "A" area as shown in Fig. 1-2-B. If it is
located in "B" area, adjust again.
3. While turning the S Reel clockwise, confirm that the
edge of the Tension Arm is located in the position
described above.
1-1: CONFIRMATION AND ADJUSTMENT OF REEL
DISK HEIGHT
Standard line of Main Chassis
1. Turn on the power and set to the STOP mode.
2. Set the master plane (JG022) and reel disk height
adjustment jig (JG024A) on the mechanism framework,
taking care not to scratch the drum, as shown in Fig. 11-A.
3. While turning the reel and confirm the following points.
Check if the surface "A" of reel disk is lower than the
surface "B" of reel disk height adjustment jig (JG024A)
and is higher than the surface "C". If it is not passed,
place the height adjustment washers and adjust to
10(+2, -0)mm.
4. Adjust the other reel in the same way.
Tension Arm
0.5mm (Adjusting range)
Standard line center of Main Chassis
Tension Adjust
Fig. 1-2-A
Master Plane (JG022)
(A)
Cut Position
Reel Disk Height Adjustment Jig
(JG024A)
(B)
Tension Adjust
Fig. 1-2-B
1-3: CONFIRMATION OF PLAYBACK TORQUE AND
BACK TENSION TORQUE DURING PLAYBACK
Fig. 1-1-A
Reel Disk Height
Adjustment Jig
(JG024A)
Reel Disk
Master Plane (JG022)
(B)
10(+0.2, -0)mm
(C)
1. Load a video tape (T-120) recorded in standard speed
mode. Set the unit to the PLAY mode.
2. Install the tentelometer as shown in Fig. 1-3. Confirm that
the meter indicates 20 ± 2gf in the beginning of playback.
• USING A CASSETTE TYPE TORQUE TAPE (KT-300NR)
1. After confirmation and adjustment of Tension Post
position (Refer to item 1-2), load the cassette type
torque tape (KT-300NR) and set to the PLAY mode.
2. Confirm that the right meter of the torque tape indicates
60~110gf•cm during playback in SP mode.
3. Confirm that the left meter of the torque tape indicates
25~40gf•cm during playback in SP mode.
Tentelometer
(A)
Video Tape
Height Adjustment
Washer
2.6x4.7xT0.13
2.6X4.7xT0.25
Fig. 1-1-B
P1 Post
Guide Roller
Fig. 1-3
MECHANICAL ADJUSTMENTS
1-4: CONFIRMATION OF VSR TORQUE
NOTE
1. Install the Torque Gauge (JG002F) and Adapter (JG002B)
on the S Reel. Set to the Picture Search (Rewind) mode.
(Refer to Fig.1-4)
2. Then, confirm that it indicates 120~180gf•cm.
If the torque is out of the range, replace the following
parts.
NOTE
Install the Torque Gauge on the reel disk firmly. Press the
REW button to turn the reel disk.
Check item
Replacement Part
1-4
Idler Ass'y/Clutch Ass'y
1-5
S Reel side: S Reel/Tension Band Ass'y/
Tension Arm Ass'y
T Reel side: T Reel/T Brake Spring/T Brake
Ass'y
1-5: CONFIRMATION OF REEL BRAKE TORQUE
(S Reel Brake) (Refer to Fig. 1-4-B)
1. Once set to the Fast Forward mode then set to the Stop
mode. While, unplug the AC cord when the Pinch Roller
Block is on the position of Fig. 1-4-A.
2. Move the Idler Ass'y from the S Reel.
3. Install the Torque Gauge (JG002F) and Adapter
(JG002B) on the S Reel. Turn the Torque Gauge
(JG002F) clockwise.
4. Then, confirm that it indicates 60~100gf•cm.
2. CONFIRMATION AND ADJUSTMENT
OF TAPE RUNNING MECHANISM
Tape Running Mechanism is adjusted precisely at the
factory. Adjustment is not necessary as usual. When you
replace the parts of the tape running mechanism because
of long term usage or failure, the confirmation and
adjustment are necessary.
(T Reel Brake) (Refer to Fig. 1-4-B)
2-1: GUIDE ROLLER
1. Once set to the Fast Forward mode then set to the Stop
mode. While, unplug the AC cord when the Pinch Roller
Block is on the position of Fig. 1-4-A.
2. Move the Idler Ass'y from the T Reel.
3. Install the Torque Gauge (JG002E) and Adapter
(JG002B) on the T reel. Turn the Torque Gauge
(JG002E) counterclockwise.
4. Then, confirm that it indicates 45~70gf•cm.
1. Playback the VHS Alignment Tape.
2. Connect CH-1 of the oscilloscope to TP4001 (Envelope)
and CH-2 to TP1002 (SW Pulse).
3. Press and hold the Tracking-Auto button on the remote
control more than 2 seconds to set tracking to center.
4. Trigger with SW Pulse and observe the envelope. (Refer
to Fig. 2-1-A)
5. When observing the envelope, adjust the Taper Nut
Driver slightly until the envelope will be flat.
Even if you press the Tracking Button, adjust so that
flatness is not moved so much.
6. Adjust so that the A : B ratio is better than 3 : 2 as shown
in Fig. 2-1-B, even if you press the Tracking Button to
move the envelope (The envelope waveform will begin to
decrease when you press the Tracking Button).
7. Adjust the PG shifter during playback.
(Refer to the ELECTRICAL ADJUSTMENTS)
The position at FF mode.
Pinch Roller Block
Stop at this position.
Cassette
Opener
The position at
STOP mode.
Capstan DD Unit
NOTE
Cassette Holder Ass'y
Fig. 1-4-A
Torque Gauge/Adapter
(JG002F/JG002B)
After adjustment, confirm and adjust A/C head.
(Refer to item 2-2)
CH-1
Envelope
(TP4001)
CH-1
Track
Torque Gauge/Adapter
(JG002E/JG002B)
CH-2
Track
CH-2
SW Pulse (TP1002)
Fig. 2-1-A
Entrance
S Reel
Max
T Reel
A
Exit
B
A:B≥3:2
Fig. 1-4-B
Max
Fig. 2-1-B
MECHANICAL ADJUSTMENTS
2-2: CONFIRMATION AND ADJUSTMENT OF AUDIO/
CONTROL HEAD
2-3: TAPE RUNNING ADJUSTMENT
(X VALUE ADJUSTMENT)
When the Tape Running Mechanism does not work well,
adjust the following items.
1. Confirm and adjust the height of the Reel Disk.
(Refer to item 1-1)
2. Confirm and adjust the position of the Tension Post.
(Refer to item 1-2)
3. Adjust the Guide Roller. (Refer to item 2-1)
4. Confirm and adjust the Audio/Control Head.
(Refer to item 2-2)
5. Connect CH-1 of the oscilloscope to TP4001, CH-2 to
TP1002 and CH-3 to HOT side of Audio Out Jack.
6. Playback the VHS Alignment Tape.
7. Press and hold the Tracking-Auto button on the remote
control more than 2 seconds to set tracking to center.
8. Set the X Value adjustment driver (JG153) to the 4 of
Fig. 2-2-B. Adjust X value so that the envelope waveform
output becomes maximum. Check if the relation between
Audio and Envelope waveform becomes (1) or (2) of Fig.
2-3.
1. Playback the VHS Alignment Tape.
2. Confirm that the reflected picture of stamp mark is
appeared on the tape prior to P4 Post as shown in Fig.
2-2-A.
a) When the reflected picture is distorted, turn the screw
1 clockwise until the distortion is disappeared.
b) When the reflected picture is not distorted, turn the
screw 1 counterclockwise until little distortion is
appeared, then adjust the a).
3. Turn the screw 2 to set the audio level to maximum.
4. Confirm that the bottom of the Audio/ Control Head and
the bottom of the tape is shown in Fig. 2-2-C.
c) When the height is not correct, turn the screw 3 to
adjust the height. Then, adjust the 1~3 again.
Audio/Control Head
Reflected picture of
Stamp Mark
Envelope
P4 Post
(1)
CH-3
Audio
(2)
Fig. 2-3
Stamp Mark
Fig. 2-2-A
Audio/Control Head
3
1
2
4
Fig. 2-2-B
Audio/Control Head
Tape
0.25±0.05mm
Fig. 2-2-C
MECHANICAL ADJUSTMENTS
3. MECHANISM ADJUSTMENT PARTS LOCATION GUIDE
5
6
4
3
7
2
1
8
10
1. Tension Adjust
2. Tension Arm
3. Guide Roller
4. P1 Post
5. Audio/Control Head
9
6. X value adjustment driver hole
7. P4 Post
8. T Brake Spring
9. T Reel
10. S Reel
ELECTRICAL ADJUSTMENTS
1. ADJUSTMENT PROCEDURE
2. BASIC ADJUSTMENTS
Read and perform these adjustments when repairing the
circuits or replacing electrical parts or PCB assemblies.
(VCR SECTION)
CAUTION
• Use an isolation transformer when performing any
service on this chassis.
• Before removing the anode cap, discharge electricity
because it contains high voltage.
• When removing a PCB or related component, after
unfastening or changing a wire, be sure to put the wire
back in its original position.
Inferior silicon grease can damage IC's and transistors.
• When replacing IC's and transistors, use only specified
silicon grease.
Remove all old silicon before applying new silicon.
On-Screen Display Adjustment
1. Unplug the AC plug for more than 5 seconds to set the
clock to the non-setting state. Then, set the volume
level to minimum.
2. Press the VOL. DOWN button on the set and the
channel button (9) on the remote control
simultaneously to display adjustment mode on the
screen as shown in Fig. 1-1.
2-1: PG SHIFTER
1. Connect CH-1 on the oscilloscope to TP1002 and CH-2
to TP4001.
2. Playback the alignment tape.
3. Press and hold the Tracking-Auto button on the remote
control more than 2 seconds to set tracking to center.
4. Press the VOL. DOWN button on the set and the
channel button (3) on the remote control simultaneously
until the indicator REC disappears. If the indicator REC
disappears, adjustment is completed.
(If the above adjustments doesn't work well:)
5. Press the VOL. DOWN button on the set and the
channel button (3) on the remote control simultaneously
until the indicator REC disappears.
6. When the REC indicator is blinking, press both VOL.
DOWN button on the set and the channel button (4) on
the remote control simultaneously and adjust the
Tracking +/- button until the arising to the down of Head
Switching Pulse becomes 6.5 ± 0.5H.
(Refer to Fig. 2-1-A, B)
7. Press the Tracking Auto button.
TV
CH-2
6.5H
00 OSD
15
CH-1
Fig. 1-1
Fig. 2-1-A
3. Use the Channel UP/DOWN button or Channel button
(0-9) on the remote control to select the options shown
in Fig. 1-2.
4. Press the MENU button on the remote control to end
the adjustments.
NO.
00
01
02
03
04
05
06
07
08
09
10
11
12
FUNCTION
OSD H
CUT OFF
RF AGC
VIF VCO
H VCO
H PHASE
V SIZE
V SHIFT
R DRIVE
B DRIVE
R CUT OFF
G CUT OFF
B CUT OFF
NO.
13
14
15
16
17
18
19
20
21
22
23
24
FUNCTION
BRIGHTNESS
CONTRAST
COLOR
TINT
SHARPNESS
FM LEVEL
LEVEL
SEPARATION 1
SEPARATION 2
TEST MONO
TEST STEREO
X-RAY TEST
Fig. 1-2
CH-2
CH-1
6.5H
Fig. 2-1-B
2-2: VCO FREERUN
1. Receive the VHF HIGH.
2. Place the set with Aging Test for more than 10 minutes.
3. Connect the digital voltmeter between the pin 7 of
CP602 and the pin 1 (GND) of CP602.
4. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (03) on the remote control to
select "VIF VCO".
5. Press the VOL. UP/DOWN button on the remote control
until the digital voltmeter is 2.5V.
ELECTRICAL ADJUSTMENTS
2-3: RF AGC
2-8: WHITE BALANCE
1. Receive the VHF HIGH (63dB).
2. Connect the digital voltmeter between the pin 5 of
CP602 and the pin 1 (GND) of CP602.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (02) on the remote control to
select "RF AGC".
4. Press the VOL. UP/DOWN button on the remote
control until the digital voltmeter is 2.8 ± 0.05V.
NOTE: Adjust after performing CUT OFF adjustment.
2-4: STEREO SEPARATION
1. Receive the stereo signal. (L=2KHz, R=400Hz)
2. Connect the AC voltmeter to AUDIO OUT L/R through
stereo filter (L=400Hz, R=2KHz).
3. Press the AUDIO SELECT button on the remote control
to set to the stereo mode.
4. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (18) on the remote control to
select "FM LEVEL".
5. Press the VOL. UP/DOWN button on the remote
control until the difference between with the stereo filter
and without the stereo filter is more than 23dB.
(TV SECTION)
2-5: CONSTANT VOLTAGE
1. Connect the digital voltmeter to the TP401.
2. Set condition is AV MODE without signal.
3. Adjust the VR502 until the DC voltage is 111 ± 0.5V.
2-6: OSD HORIZONTAL
1. Activate the adjustment mode display of Fig. 1-1.
2. Press the VOL. UP/DOWN button on the remote control
until the difference of A and B becomes minimum.
(Refer to Fig. 2-3)
1. Place the set with Aging Test for more than 15 minutes.
2. Receive the color bar pattern.
3. Using the remote control, set the brightness and contrast
to normal position.
4. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (10) on the remote control to
select "R CUT OFF".
5. Using the VOL. UP/DOWN button on the remote control,
adjust the R CUT OFF.
6. Press the CH. UP/DOWN button on the remote control to
select the "R DRIVE", "B DRIVE", "G CUT OFF" or "B
CUT OFF".
7. Using the VOL. UP/DOWN button on the remote control,
adjust the R DRIVE, B DRIVE, G CUT OFF or B CUT
OFF.
8. Perform the above adjustments 6 and 7 until the white
color is looked like a white.
2-9: FOCUS
1. Receive the monoscope pattern.
2. Turn the Focus Volume fully counterclockwise once.
3. Adjust the Focus Volume until picture is distinct.
2-10: HORIZONTAL PHASE
1. Receive the monoscope pattern.
2. Using the remote control, set the brightness and
contrast to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (05) on the remote control to
select "H PHASE".
4. Press the VOL. UP/DOWN button on the remote
control until the SHIFT quantity of the OVER SCAN on
right and left becomes minimum.
2-11: HORIZONTAL SIZE
TV
NOTE: Adjust after performing adjustments in section 2-10.
1. Receive the monoscope pattern.
2. Adjust the VR401 until the SHIFT quantity of the OVER
SCAN on right and left becomes 10 ± 2%.
00 OSD
2-12: VERTICAL SIZE
15
NOTE: Adjust after performing adjustments in section 2-11.
A
B
Fig. 2-3
2-7: CUT OFF
1. Adjust the unit to the following settings.
R CUT OFF=128, G CUT OFF=128, B CUT OFF=128,
R DRIVE=64, B DRIVE=64, BRIGHTNESS=100,
CONTRAST=85
2. Place the set with Aging Test for more than 15 minutes.
3. Set condition is AV MODE without signal.
4. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (01) on the remote control to
select "CUT OFF".
5. Adjust the Screen Volume until a dim raster is obtained.
1. Receive the cross hatch signal from the Pattern
Generator.
2. Using the remote control, set the brightness and
contrast to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (06) on the remote control to
select "V SIZE".
4. Press the VOL. UP/DOWN button on the remote
control until the rectangle on the center of the screen
becomes square.
5. Receive a broadcast and check if the picture is normal.
ELECTRICAL ADJUSTMENTS
2-13: VERTICAL SHIFT
White 0%
NOTE: Adjust after performing adjustments in section 2-12.
1. Receive the center cross signal from the Pattern
Generator.
2. Using the remote control, set the brightness and
contrast to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (07) on the remote control to
select "V SHIFT".
4. Please the VOL. UP/DOWN button on the remote
control until the horizontal line becomes fit to the notch
of the shadow mask.
"A"
Fig. 2-4
White 100%
2-14: SUB BRIGHTNESS
2-17: SUB COLOR
1. Receive the monoscope pattern. (RF Input)
2. Using the remote control, set the brightness and
contrast to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (13) on the remote control to
select "BRIGHTNESS".
4. Press the VOL. UP/DOWN button on the remote
control until the white 10% is starting to be visible.
5. Receive the monoscope pattern. (Audio Video Input)
6. Press the INPUT SELECT button on the remote control
to set to the AV mode. Then perform the above
adjustments 2~4.
1. Receive the color bar pattern. (RF Input)
2. Using the remote control, set the brightness, contrast,
color and tint to normal position.
3. Connect the oscilloscope to TP804.
4. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (15) on the remote control to
select "COLOR".
5. Adjust the VOLTS RANGE VARIABLE knob of the
oscilloscope until the range between white 100% and
0% is set to 4 scales on the screen of the oscilloscope.
6. Press the VOL. UP/DOWN button on the remote
control until the red color level is adjusted to 110 ± 5%
of the white level. (Refer to Fig. 2-5)
7. Receive the color bar pattern. (Audio Video Input)
8. Press the INPUT SELECT button on the remote control
to set to the AV mode. Then perform the above
adjustments 2~6.
2-15: SUB CONTRAST
1. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (14) on the remote control to
select "CONTRAST".
2. Press the VOL. UP/DOWN button on the remote
control until the contrast step No. becomes "85".
3. Receive the color bar pattern. (Audio Video Input)
4. Press the INPUT SELECT button on the remote control
to set to the AV mode. Then perform the above
adjustments 1, 2.
White 0%
0%
2-16: SUB TINT
1. Receive the color bar pattern. (RF Input)
2. Using the remote control, set the brightness, contrast,
color and tint to normal position.
3. Connect the oscilloscope to TP806.
4. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (16) on the remote control to
select "TINT".
5. Press the VOL. UP/DOWN button on the remote
control until the section "A" becomes a straight line.
(Refer to Fig. 2-4)
6. Receive the color bar pattern. (Audio Video Input)
7. Press the INPUT SELECT button on the remote control
to set to the AV mode. Then perform the above
adjustments 2~5.
100%
White 100%
Red Level
Fig. 2-5
2-18: PIN CUSHION (PCC)
1. Receive the color bar pattern.
2. Using the remote control, set the brightness and
contrast to normal position.
3. Adjust the VR402 until the right and left vertical line
becomes straight.
ELECTRICAL ADJUSTMENTS
3. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE
(VCR SECTION)
TP4001
TP1002
TP1001
CP602
TU601
J4202
J4201
TP4201
SYSCON PCB
ELECTRICAL ADJUSTMENTS
(TV SECTION)
TP806
TP804
VR402
VR401
J801
FB401
T501
FOCUS VOLUME
SCREEN VOLUME
CRT PCB
VR502
TP401
R449
MAIN PCB
ELECTRICAL ADJUSTMENTS
4. PURITY AND CONVERGENCE
ADJUSTMENTS
4-3: STATIC CONVERGENCE
NOTE
Adjust after performing adjustments in section 4-2.
NOTE
1. Turn the unit on and let it warm up for at least 30
minutes before performing the following adjustments.
2. Place the CRT surface facing east or west to reduce the
terrestrial magnetism.
3. Turn ON the unit and demagnetize with a Degauss Coil.
4-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT)
1. Tighten the screw for the magnet. Refer to the adjusted
CRT for the position. (Refer to Fig. 4-1)
If the deflection yoke and magnet are in one body,
untighten the screw for the body.
2. Receive the green raster pattern from the color bar
generator.
3. Slide the deflection yoke until it touches the funnel side
of the CRT.
4. Adjust center of screen to green, with red and blue on
the sides, using the pair of purity magnets.
5. Switch the color bar generator from the green raster
pattern to the crosshatch pattern.
6. Combine red and blue of the 3 color crosshatch pattern
on the center of the screen by adjusting the pair of 4
pole magnets.
7. Combine red/blue (magenta) and green by adjusting the
pair of 6 pole magnets.
8. Adjust the crosshatch pattern to change to white by
repeating steps 6 and 7.
4-2: PURITY
1. Receive the crosshatch pattern from the color bar
generator.
2. Combine red and blue of the 3 color crosshatch pattern
on the center of the screen by adjusting the pair of 4
pole magnets.
3. Combine red/blue (magenta) and green by adjusting the
pair of 6 pole magnets.
4-4: DYNAMIC CONVERGENCE
NOTE
Adjust after performing adjustments in section 4-3.
1. Adjust the differences around the screen by moving the
deflection yoke upward/downward and right/left.
(Refer to Fig. 4-2-a)
2. Insert three wedges between the deflection yoke and
CRT funnel to fix the deflection yoke.
(Refer to Fig. 4-2-b)
RGB
R
G
B
RGB
R
G
B
UPWARD/DOWNWARD SLANT
NOTE
RIGHT/LEFT SLANT
Fig. 4-2-a
Adjust after performing adjustments in section 4-1.
1. Receive the green raster pattern from color bar
generator.
2. Adjust the pair of purity magnets to center the color on
the screen.
Adjust the pair of purity magnets so the color at the
ends are equally wide.
3. Move the deflection yoke backward (to neck side)
slowly, and stop it at the position when the whole screen
is green.
4. Confirm red and blue colors.
5. Adjust the slant of the deflection yoke while watching
the screen, then tighten the fixing screw.
DEFLECTION YOKE
DEFLECTION YOKE SCREW
MAGNET SCREW
6 POLE MAGNETS
4 POLE MAGNETS
PURITY MAGNETS
Fig. 4-1
WEDGE
WEDGE
WEDGE
WEDGE POSITION
Fig. 4-2-b
MECHANICAL EXPLODED VIEW
201
201
201
201
205
201
132
116
J801
123
201
116
124
132
131
PCB110
(CRT PCB)
132
L503
213
V801
SP352
210
212
132
206
210
212
127
206
117
PCB070
(MAIN PCB)
207
119
207
206
207
122
206
212
207
114
212
SP351
206
121
A
202
120
PCB030
(OPERATION PCB)
B
118
101
MECHANICAL EXPLODED VIEW
209
126
211
A
205
203
203
203
205
125
130
103
202
109
201
212
PCB330
(COMB PCB)
112
208
TU601
207
201
PCB010
(SYSCON PCB)
133
B
106
128
102
111
204
CHASSIS EXPLODED VIEW (TOP VIEW)
503
300
352
510
503
M2003
UN4001
335
502
319
507
334
AA
H5001
502
318
H5002
314
321
501
506
349
348
328
305
356
347
310
336
301
512
304
512
355
313
303
315
338
317
361
316
AA
AA
AA
309
AA
AA
AA
320
AA
M101
359
360
357
329
364
BA
360
358
AA
330
AA
306
509
353
AA
508
PCB550
(DECK PCB ASS'Y)
502
AA
AA
363
351
362
323
365
324
AA
511
CLASS
MARK
GREASE
AA
OIL
BA
NOTE: Applying positions AA and BA for the grease or
oil are displayed for this section.
Check if the correct grease or oil is applied for
each position.
CHASSIS EXPLODED VIEW (BOTTOM VIEW)
302
300
M2001
511
AA
340
AA
505
AA
341
AA
344
503
AA
343
AA
346
505
339
AA
342
326
332
345
322
350
513
333
346
331
311
AA
AA
AA
307
AA
AA
312
AB
354
327
308
325
AA
AA
AA
337
AA
504
CLASS
MARK
GREASE
AA
OIL
BA
NOTE: Applying positions AA and BA for the grease or
oil are displayed for this section.
Check if the correct grease or oil is applied for
each position.
MECHANICAL REPLACEMENT PARTS LIST
Location No. TSB P/N
Reference No.
Description
101
102
103
106
109
BZ610242
BZ710248
BZ710328
BZ710249
BZ710250
A59504Q720
752WSAA028
752WSA0209
761WPA0198
771WPA0256
CABINET,FRONT ASSY
SHIELD,BOTTOM
SHIELD,CASE HEAD AMP
HOLDER,DECK
PLATE,JACK
111
112
114
116
117
118
119
BZ710252
BZ710178
BZ710459
BZ710259
BZ710260
BZ710453
BZ710463
800WFA0038
85OP700036
761WPA0223
762WPA0011
899HV3T000
701WPJB361
712WPJB161
CUSHION
HOLDER,EOT SENSOR
HOLDER,FBT
HOLDER,CRT WIRE
HOLDER,ANODE WIRE
CABINET,FRONT
FLAP
120
121
122
123
124
125
126
127
128
BZ710455
BZ710456
BZ710010
BZ710457
BZ610243
BZ710381
BZ710012
BZ710039
BZ710251
713WPA0165
735WPBA243
743WKA0032
702WPAA169
A59504Q740
752WSA0234
761WPA0151
8995034000
800WFA0037
GLASS,LED
BUTTON,FRAME
SPRING,FLAP
CABINET,BACK ASS'Y
CABINET,BACK ASSY
PLATE,DECK SHIELD ASS'Y
HOLDER,M/PCB
CORD CLIP UL CO.
CUSHION
130
131
132
133
BZ710331
BZ710258
BZ710275
BZ710235
753WUAA006
741WUA0001
8121J50B54
753WSA0120
SPRING,EARTH HEAD AMP
SPRING,EARTH
SCREW,TAPPING(B0) GW20
PLATE,BOTTOM-EARTH
201
202
203
204
205
206
207
208
209
BZ710036
BZ710031
BZ710034
BZ710158
BZ710032
BZ710030
BZ710239
BZ710028
BZ710018
8117540B04
8110630A04
8117140A24
8110630604
8110630A24
8110630804
8109I30A04
8110330804
8107630804
SCREW,TAPPING(B0) TRUSS
SCREW,TAP TITE(P) BRAZIER
SCREW,TAPPING(B0) PAN
SCREW,TAP TITE(P) BRAZIER
SCREW,TAP TITE(P) BRAZIER
SCREW,TAP TITE(P) BRAZIER
SCREW,TAP TITE(B) WH7
SCREW,TAP TITE(P) FLAT
SCREW,TAP TITE(S) BRAZIER
4x20
3x10
4x12
3x6
3x12
3x8
3x10
3x8
3x8
210
211
212
213
BZ710337
BZ710017
BZ710019
BZ710024
8107930604
8107226604
8109630802
810A130B04
SCREW,CUP(S)
SCREW,TAP TITE(S) BIND
SCREW,TAP TITE(B) BRAZIER
SCREW/WASHER(A)
3x6
2.6x6
3x8
M3x20
---------
BZ710410
BZ710411
BZ710458
BZ614286
792WHA0317
792WHA0318
793WCDB017
J5950401
PACKAGE,TOP
PACKAGE,BOTTOM
GIFT BOX
INSTRUCTION BOOK
10x10xT=2
15x5xT=6
5x28
CHASSIS REPLACEMENT PARTS LIST
Location No. TSB P/N Reference No.
Description
300
301
302
303
304
305
306
307
308
309
BZ610233
BZ710073
BZ710193
BZ710132
BZ710094
BZ710112
BZ710354
BZ710195
BZ710355
BZ710197
A59501A420A
85OA500022
85OP200290
85OP900710
85OP500083
85OP800324
85OA000449
85OA200082
85OA200088
85OP600556
DECK ASSY
AHC ASS'Y
BELT,CAPSTAN (S)
LEVER,REC
BASE,AC HEAD
SPRING,AC HEAD
MAIN CHASSIS ASS'Y (3V)
CLUTCH ASS'Y(S2)
ARM,IDLER ASS'Y 3V
ARM,SS BRAKE (S)
310
311
312
313
314
315
316
317
318
319
BZ710198
BZ710063
BZ710064
BZ710216
BZ710356
BZ710357
BZ710200
BZ710072
BZ710065
BZ710374
85OP200292
85OA300061
85OA300062
85OP900714
85OA400220
85OA400221
85OA400199
85OA400205
85OA400175
85OA400216
REEL,T (S)
LOADING ARM S ASS'Y
LOADING ARM T ASS'Y
COVER,SENSOR L3
INCLINED BASE S UNIT 3V
INCLINED BASE T UNIT 3V
P5-3 ARM ASS'Y(S)
PINCH ROLLER BLOCK
TENSION ARM ASS'Y
TENSION BAND ASS'Y 3V
320
321
322
323
324
325
326
327
328
329
BZ710067
BZ710375
BZ710359
BZ710360
BZ710361
BZ710204
BZ710205
BZ710206
BZ710207
BZ710362
85OA400178
85OA600197
85OP500087
85OA900223
85OP900716
85OP200284
85OP200285
85OP200298
85OP200291
85OP600566
PINCH ROLLER LEVER ASS'Y
BRAKE T ASS'Y 3V
HOLDER,SPRING(SV)
LINK UNIT(SV)
LEVER,LINK(SV)
LEVER,CLUTCH (S)
ACTUATOR,CLUTCH
GEAR,COUPLING(S2)
REEL,S (S)
WORM(SV)
330
331
332
333
334
335
336
337
338
339
BZ710363
BZ710364
BZ710087
BZ710088
BZ710365
BZ710090
BZ710093
BZ710092
BZ710366
BZ710097
85OP600567
85OP300193
85OP300179
85OP300180
85OP300189
85OP400472
85OP400492
85OP400490
85OP400520
85OP600543
BRACKET,MOTOR(SV)
GEAR,MAIN LOADING
GEAR,LOADING S
GEAR,LOADING T
HOLDER,LOADING GEAR (S-ZV)
ADJUST,TENSION
HOLDER,TENSION
LEVER,TENSION
CAP.P4
GEAR,JOINT
340
341
342
343
344
345
346
347
348
349
BZ710098
BZ710367
BZ710101
BZ710172
BZ710210
BZ710106
BZ710107
BZ710211
BZ710212
BZ710110
85OP600544
85OP600572
85OP600546
85OP600565
85OP600561
85OP700035
85OP800318
85OP800334
85OP800335
85OP800322
GEAR,MIDDLE
CAM,MAIN(S)
CAM,P5
CAM,PINCH ROLLER
ROD,MAIN(S)
REFLECTOR,LED
SPRING,LOADING GEAR
SPRING,P5 (S)
SPRING,BRAKE T (S)
SPRING,TENSION
350
351
352
353
354
355
356
357
358
359
BZ710213
BZ710118
BZ710128
BZ710217
BZ710115
BZ710214
BZ710119
BZ710368
BZ710369
BZ710314
85OP800336
85OP800342
85OP900695
85OP900713
85OP800330
85OP800337
85OP900680
85OP900722
85OP900723
85OP900728
SPRING,CAP BRAKE (S)
SPRING,LOCKER (S)
BRACKET,TOP
LOCKER,R2
SPRING,RING
SPRING,SS BRAKE (S)
OPENER,CASS
CASS SIDE L(SV)
CASS SIDE R(SV)
TAPE GUIDE L(P,R)
360
361
362
363
364
365
BZ710127
BZ710117
BZ710123
BZ710370
BZ710129
BZ710315
85OP900694
85OP800341
85OP900688
85OP900717
85OP900696
85OP900729
SPRING,PACK
SPRING,P/R ARM
LEVER,FLAP
CASS HOLDER(SV)
SPRING,CASS EARTH
TAPE GUIDE R
A59501A420A
CHASSIS REPLACEMENT PARTS LIST
Location No. TSB P/N Reference No.
!
!
!
!
Description
501
502
503
504
505
506
507
508
509
BZ710048
BZ710049
BZ710017
BZ710050
BZ710058
BZ710371
BZ710046
BZ710219
BZ710241
8107126A04
8107226804
8107226604
8109126604
83ETW30000
8107226404
8102120604
810A126504
810A130504
SCREW,TAP TITE(S) PAN
SCREW,TAP TITE(S) BIND
SCREW,TAP TITE(S) BIND
SCREW,TAP TITE(B) PAN
E-RING
SCREW,TAP TITE(S) BIND
SCREW,PAN
SCREW/WASHER(A)
SCREW/WASHER(A)
2.6x10
2.6x8
2.6x6
2.6x6
3.0
2.6x4
M2x6
M2.6x5
M3x5
510
511
512
513
BZ710390
BZ710055
BZ710218
BZ710054
8107226504
82P266005N
82Q2647C5N
82P184505N
SCREW,TAP TITE(S) BIND
POLYSLIDER WASHER(CUT)
POLYSLIDER WASHER
POLYSLIDER WASHER(CUT)
2.6x5
2.6x6.0xT0.5
2.6x4.7xT0.25
1.8x4.5xT0.5
CP101
H5001
H5002
M101
M2001
M2003
PCB550
Q101
UN4001
BZ614040
BZ710040
BZ710041
BZ710044
BZ710372
BZ710391
BZ610053
BZ410026
BZ610201
069R740018
1523D91034
1543D02013
1596P78001
1594S98001
1589S11015
A4C831B550
0000700320
A4E404B500
CONNECTOR PCB SIDE
HEAD (AUDIO CONTROL)
HEAD (FULL ERASE)
MOTOR (LOADING)
CAPSTAN DD UNIT
MICRO MOTOR
DECK PCB ASS'Y
TRANSISTOR,PHOTO
CYLINDER UNIT ASS'Y
52044-0445
HVMXA1072A
HVFHP0032A
MXN13FB11H
F2QSB36
I2OAL01
VE8851
RPT-38PB113
A4E404B500
ELECTRICAL REPLACEMENT PARTS LIST
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
Location No.
TSB P/N
Reference No.
RESISTORS
R402
R418
R436
R437
R439
R441
R443
R444
R447
R448
R449
R450
R452
R500
R501
R512
R517
R528
R529
R542
R543
R650
R804
R806
R808
R4068
BZ210165
BZ210150
BZ210054
BZ210039
BZ210151
BZ210013
BZ210198
BZ210056
BZ210021
BZ210153
BZ210057
BZ210079
BZ210059
BZ210001
BZ210043
BZ210061
BZ210199
BZ210062
BZ210084
BZ210200
BZ210064
BZ210126
BZ210050
BZ210050
BZ210050
BZ210118
R3X18AR56J
R002T2010J
R65582120J
R3X181010J
R4X5T4273F
R4X5T4104F
R4X5T4122F
R4X5T4123F
R65582680J
R3X181102J
R5X2CE272J
R6558A4R7J
R3X1812R2J
R21202275K
R5Y2CE2R2J
R3X28A103J
R3X18A010J
R3X28B223J
R4X5T4272F
R33681R13J
R63584681J
R002T4222J
R3X18A123J
R3X18A123J
R3X18A123J
R002T4473J
C321
C407
C413
C421
C423
C426
C427
C428
C430
C431
C433
C437
C443
C450
C502
C503
C505
C506
C507
C510
C514
C517
C520
C521
C523
C524
C529
C530
C531
C537
C664
C808
C1021
C5558
BZ110053
BZ110101
BZ110054
BZ110055
BZ110056
BZ110123
BZ110057
BZ110058
BZ110123
BZ110059
BZ110020
BZ110160
BZ110060
BZ110123
BZ110144
BZ110144
BZ110138
BZ110145
BZ110012
BZ110063
BZ110113
BZ110095
BZ110028
BZ110130
BZ110065
BZ110032
BZ110066
BZ110008
BZ110101
BZ110146
BZ110147
BZ110123
BZ110163
BZ210163
E02LF3102M
E5EZF3222M
P3N1F5333J
E5EZF4102M
P447F2474J
C0JLYR713K
E53FF56R8K
P4N8FJ123H
C0JLYR713K
E0ELTD100M
E5EZT8220M
E02LT5101M
P4N8FJ222H
C0JLYR713K
C13VB07H3K
C13VB07H3K
P2472B224M
P2472B104M
E51CGC471M
E5EZT5470M
C0JLYR7K3K
C0JLYR7E3K
E5EZT2102M
E62NFC221M
E5EZT4471M
E5EZF3102M
C034E0J13M
C034E0JH3M
E5EZF3222M
E02LU5R47M
P235WE105J
C0JLYR713K
E5EZT4330M
P1S3T0152J
D301
D302
D401
D403
D404
D406
D407
D408
D409
D410
D411
D412
D413
D414
D415
BZ410034
BZ410034
BZ410043
BZ410019
BZ410019
BZ410014
BZ410051
BZ410018
BZ410017
BZ410022
BZ410014
BZ410014
BZ410014
BZ410014
BZ410014
D97U01301B
D97U01301B
D2WT011E10
D97U03001B
D97U03001B
D2LTPG06J0
DCBFMV3FU0
D94TA27011
D94TA11B13
D97U06R81B
D2LTPG06J0
D2LTPG06J0
D2LTPG06J0
D2LTPG06J0
D2LTPG06J0
R,METAL OXIDE
RC
R,FUSE
R,METAL OXIDE
R,METAL
R,METAL
R,METAL
R,METAL
R,FUSE
R,METAL OXIDE
R,CEMENT
R,FUSE
R,METAL OXIDE
R,SOLID
R,CEMENT
R,METAL OXIDE
R,METAL OXIDE
R.METAL
R,METAL
R,METAL
R,FUSE
RC
R,METAL OXIDE
R,METAL OXIDE
R,METAL OXIDE
RC
Description
0.56 OHM 2W
1 OHM 1/2W
12 OHM 1/2W
1 OHM 1W
27K OHM 1/4W
100K OHM 1/4W
1.2K OHM 1/4 W
12K OHM 1/4W
68 OHM 1/2W
1K OHM 1W
2.7K OHM 7W
4.7 OHM 2W
2.2 OHM 1W
2.7M OHM 1/2W
2.2 OHM 7W
10K OHM 2W
1 OHM 2W
22K OHM 3W
2.7K OHM 1/4W
0.13OHM 1W
680 OHM 1/4W
2.2K OHM 1/4W
12K OHM 2W
12K OHM 2W
12K OHM 2W
47K OHM 1/4W
CAPACITORS
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
CE
CE
CPP
CE
CMPP
CC
CE
CMPP
CC
CE
CE
CE
CMPP
CC
CC
CC
CMP
CMP
CE
CE
CC
CC
CE
CE
CE
CE
CC
CC
CE
CE
CMP
CC
CE
CP
1000 UF 25V
2200 UF 25V
0.033 UF 630V
1000 UF 35V
0.47 UF 200V FHS
0.001 UF 2KV YR
6.8 UF 50V NP
0.012 UF 1.25KV
0.001 UF 2KV YR
10 UF 250V
22 UF 100V
100 UF 50V
0.0022UF 1.25KV
0.001 UF 2KV YR
0.0022UF 2KV B
0.0022UF 2KV B
0.22UF 275V PHE840
0.1 UF 275V PHE840
470 UF 200V
47 UF 50V
0.0027UF 2KV YR
0.0015UF 2KV YR
1000 UF 16V
220 UF 200V
470 UF 35V
1000 UF 25V
0.001 UF 125V MX
0.0022UF 125V MX
2200 UF 25V
0.47 UF 50V
1 UF 63V MKT
0.001 UF 2KV YR
33 UF 35V
0.0015UF 50V
DIODES
!
!
!
!
!
!
!
DIODE,ZENER
DIODE,ZENER
DIODE,SILICON
DIODE,ZENER
DIODE,ZENER
DIODE,SILICON
DIODE
DIODE,ZENER
DIODE,ZENER
DIODE,ZENER
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
MTZJ13B T-77
MTZJ13B T-77
11E1-EIC
MTZJ30B T-77
MTZJ30B T-77
RMPG06J-G3
FMV-3FULF027-102
HZ27-1L TD
HZ11B3L TD
MTZJ6.8B T-77
RMPG06J-G3
RMPG06J-G3
RMPG06J-G3
RMPG06J-G3
RMPG06J-G3
ELECTRICAL REPLACEMENT PARTS LIST
Location No.
TSB P/N
Reference No.
DIODES
! D501
! D503
! D505
D506
D507
! D508
! D509
! D510
! D511
! D512
! D514
! D515
D517
D518
! D519
D521
D523
D524
D525
D526
D528
D529
D530
! D533
D601
D602
D605
D607
D608
D609
D610
D612
D616
D617
D618
D791
D792
D793
D801
D802
D803
D1003
D1014
D4201
D4204
D4205
D4206
D5501
BZ410044
BZ410080
BZ410052
BZ410014
BZ410008
BZ410076
BZ410052
BZ410080
BZ410011
BZ410076
BZ410076
BZ410037
BZ410006
BZ410006
BZ410076
BZ410006
BZ410006
BZ410006
BZ410006
BZ410006
BZ410021
BZ410006
BZ410006
BZ410011
BZ410006
BZ410053
BZ410059
BZ410006
BZ410022
BZ410022
BZ410008
BZ410022
BZ410006
BZ410006
BZ410006
BZ410054
BZ410054
BZ410054
BZ410006
BZ410006
BZ410006
BZ410004
BZ410021
BZ410021
BZ410006
BZ410006
BZ410034
BZ410006
D4LZBL06L0
D2WXRU2AM0
D28F21DQN9
D2LTPG06J0
D23U1003A3
D2WXB290S0
D28F21DQN9
D2WXRU2AM0
D28TELS2N2
D2WXB290S0
D2WXB290S0
D97U03301B
D1VT001330
D1VT001330
D2WXB290S0
D1VT001330
D1VT001330
D1VT001330
D1VT001330
D1VT001330
D97U05R61B
D1VT001330
D1VT001330
D28TELS2N2
D1VT001330
D97U08R21C
D2WT11ES10
D1VT001330
D97U06R81B
D97U06R81B
D23U1003A3
D97U06R81B
D1VT001330
D1VT001330
D1VT001330
0021721150
0021721150
0021721150
D1VT001330
D1VT001330
D1VT001330
0010600060
D97U05R61B
D97U05R61B
D1VT001330
D1VT001330
D97U01301B
D1VT001330
DIODE
DIODE,SILICON
DIODE,SCHOTTKY
DIODE,SILICON
DIODE,SCHOTTKY
DIODE,SILICON
DIODE,SCHOTTKY
DIODE,SILICON
DIODE,RECTIFER
DIODE,SILICON
DIODE,SILICON
DIODE,ZENER
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
DIODE,ZENER
DIODE,SILICON
DIODE,SILICON
DIODE,RECTIFER
DIODE,SILICON
DIODE,ZENER
DIODE,SILICON
DIODE,SILICON
DIODE,ZENER
DIODE,ZENER
DIODE,SCHOTTKY
DIODE,ZENER
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
LED
LED
LED
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
LED
DIODE,ZENER
DIODE,ZENER
DIODE,SILICON
DIODE,SILICON
DIODE,ZENER
DIODE,SILICON
IC301
IC352
IC401
IC501
IC502
IC506
IC601
IC603
IC901
IC1001
IC1002
IC1004
IC1099
IC4001
IC5501
BZ611034
BZ611035
BZ611053
BZ611015
BZ611036
BZ410055
BZ611055
BZ611033
BZ611079
BZ611056
BZ611057
BZ611058
BZ610232
BZ611059
BZ611024
I06DF62420
I0FSP75220
I01TD55220
I1KA97805A
I2BT06624G
0002500450
I06FC61206
I1KA97809A
I05FE90A45
I56F57059A
IC7J0311A0
I03DQ18800
A59501B015
I03F3201M0
I01F62FBP0
IC
IC
IC
IC
IC
PHOTO COUPLER
IC
IC
IC
IC
IC
IC
IC
IC
IC
BZ510002
BZ510004
BZ510029
BZ510078
BZ510073
BZ510027
BZ510040
BZ510069
BZ510073
BZ510041
BZ510029
BZ510074
T8YJ2412K0
TA3T016240
TNYTD03001
TNATJ03003
TAATA12660
TC3Q026210
TDUU024990
TCATC31980
TAATA12660
TD30016670
TNYTD03001
TDAT00863Y
Description
GBL06L-6177
RU2AM-EIC
21DQ09N-FC4
RMPG06J-G3
SB10-03A3
SB290S
21DQ09N-FC4
RU2AM-EIC
10ELS2N-TA1B2
SB290S
SB290S
MTZJ33B T-77
1SS133T-77
1SS133T-77
SB290S
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
MTZJ5.6B T-77
1SS133T-77
1SS133T-77
10ELS2N-TA1B2
1SS133T-77
MTZJ8.2C T-77
11ES1-EIC
1SS133T-77
MTZJ6.8B T-77
MTZJ6.8B T-77
SB10-03A3
MTZJ6.8B T-77
1SS133T-77
1SS133T-77
1SS133T-77
SLR-342VCT32
SLR-342VCT32
SLR-342VCT32
1SS133T-77
1SS133T-77
1SS133T-77
SID1050CM
MTZJ5.6B T-77
MTZJ5.6B T-77
1SS133T-77
1SS133T-77
MTZJ13B T-77
1SS133T-77
ICS
!
!
!
!
M62420SP
AN7522
AN5522
KIA7805API
STR-G6624
TLP621(GR)
M61206FP
KIA7809API
TC90A45F
OEC7059A
R3111N311A/C-TR
LB11880
S-24C04BDP-LA
LA71201M-MPB
AN3662FBP
TRANSISTORS
Q350
! Q401
Q402
Q403
Q404
! Q405
! Q406
Q407
Q408
Q409
Q410
Q501
TRANSISTOR,SILICON
TRANSISTOR,SILICON
COMPOUND TRANSISTOR
COMPOUND TRANSISTOR
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
COMPOUND TRANSISTOR
TRANSISTOR,SILICON
2SC2412KT146 R,S
2SA1624-AA
DTC144ESTP
KRC111MAT
KTA1266-AT(Y,GR)
2SC2621(D,E)-RAC
2SD2499(LB0EC1)
KTC3198-AT(Y,GR)
KTA1266-AT(Y,GR)
2SD1667(R,S)
DTC144ESTP
KTD863_Y-AT
ELECTRICAL REPLACEMENT PARTS LIST
Location No.
TSB P/N
Q502
Q503
Q505
Q507
Q508
Q509
Q512
Q513
Q601
Q602
Q603
Q605
Q606
Q609
Q610
Q611
Q801
Q802
Q803
Q810
Q811
Q812
Q901
Q902
Q903
Q1002
Q1003
Q1004
Q1005
Q1009
Q1013
Q1023
Q4001
Q4002
Q4003
Q4005
Q4006
Q4007
Q4009
Q4010
Q4012
Q4013
Q4203
Q4204
Q4205
Q4206
Q4210
Q4211
Q4212
BZ510005
BZ510005
BZ510011
BZ510069
BZ510057
BZ510024
BZ510011
BZ510023
BZ510001
BZ510043
BZ510043
BZ510057
BZ510044
BZ510045
BZ510031
BZ510031
BZ510027
BZ510027
BZ510027
BZ510046
BZ510046
BZ510046
BZ510002
BZ510002
BZ510002
BZ510002
BZ410041
BZ510067
BZ410049
BZ410041
BZ410042
BZ510002
BZ510069
BZ510069
BZ510026
BZ510073
BZ510070
BZ510002
BZ510001
BZ510001
BZ510002
BZ510002
BZ510002
BZ510071
BZ510071
BZ510071
BZ510001
BZ510002
BZ510001
TA3T1371A0
TA3T1371A0
TC3T029090
TCATC31980
TAAT01281Y
TNYTJ03001
TC3T029090
TNYTB03001
T6YJ1037K0
TC10013840
TC10013840
TAAT01281Y
TC5T021204
TNYJD05001
TD3T007340
TD3T007340
TC3Q026210
TC3Q026210
TC3Q026210
TC7T1740S0
TC7T1740S0
TC7T1740S0
T8YJ2412K0
T8YJ2412K0
T8YJ2412K0
T8YJ2412K0
0002700530
TNAAC05002
0002700590
0002700530
0000100380
T8YJ2412K0
TCATC31980
TCATC31980
TPYJC05001
TAATA12660
TCAT032034
T8YJ2412K0
T6YJ1037K0
T6YJ1037K0
T8YJ2412K0
T8YJ2412K0
T8YJ2412K0
TNAAB05003
TNAAB05003
TNAAB05003
T6YJ1037K0
T8YJ2412K0
T6YJ1037K0
L301
L302
L401
! L402
L481
! L501
! L503
L603
L604
L605
L607
L608
L610
L613
L618
L621
L802
L804
L901
L902
L903
L904
L1001
L4001
L4003
L4004
L4005
BZ310005
BZ310005
BZ310004
BZ310063
BZ310064
BZ310115
BZ310066
BZ310101
BZ310002
BZ310112
BZ310058
BZ310002
BZ310005
BZ310136
BZ310117
BZ310118
BZ310070
BZ310070
BZ310138
BZ310139
BZ310140
BZ310141
BZ310009
BZ310039
BZ310002
BZ310039
BZ310040
02167D101K
02167D101K
021679472K
022100027A
02D8000012
029T000093
028R200024
0216A61R2K
021673101K
021LA61R2K
021LA6220K
021673101K
02167D101K
021LA63R3K
021LA6330K
02AHB9A972
02167D820K
02167D820K
021673821K
02167F151J
02167F150J
02167F100J
021LA62R2K
02167F220J
021673101K
02167F220J
02167F470J
!
!
!
!
!
!
!
!
!
!
!
!
Reference No.
TRANSISTORS
Description
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
COMPOUND TRANSISTOR
TRANSISTOR,SILICON
COMPOUND TRANSISTOR
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
COMPOUND TRANSISTOR
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
PHOTO COUPLER
COMPOUND TRANSISTOR
PHOTO COUPLER
PHOTO COUPLER
PHOTO TRANSISTOR
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
COMPOUND TRANSISTOR
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
COMPOUND TRANSISTOR
COMPOUND TRANSISTOR
COMPOUND TRANSISTOR
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
2SA1371(D,E)-AE
2SA1371(D,E)-AE
2SC2909(S,T)-AA
KTC3198-AT(Y,GR)
KTA1281_Y
DTC114TSTP
2SC2909(S,T)-AA
DTC114ESTP
2SA1037AKT146R,S
2SC13840W
2SC13840W
KTA1281_Y
2SC2120Y(TPE2)
DTC144EKAT146
2SD734(E,F)-AA
2SD734(E,F)-AA
2SC2621(D,E)-RAC
2SC2621(D,E)-RAC
2SC2621(D,E)-RAC
2SC1740SP(R,S) TP
2SC1740SP(R,S) TP
2SC1740SP(R,S) TP
2SC2412KT146 R,S
2SC2412KT146 R,S
2SC2412KT146 R,S
2SC2412KT146 R,S
RPI-352Q01R
KRC103RTK
RPI-301
RPI-352Q01R
PNA2604M010R
2SC2412KT146 R,S
KTC3198-AT(Y,GR)
KTC3198-AT(Y,GR)
DTA124EKAT146
KTA1266-AT(Y,GR)
KTC3203_Y-AT
2SC2412KT146 R,S
2SA1037AKT146R,S
2SA1037AKT146R,S
2SC2412KT146 R,S
2SC2412KT146 R,S
2SC2412KT146 R,S
KRC102RTK
KRC102RTK
KRC102RTK
2SA1037AKT146R,S
2SC2412KT146 R,S
2SA1037AKT146R,S
COILS &TRANSFORMERS
COIL
COIL
COIL
COIL,LINEARITY
TIB PIN PHASE COIL
COIL,LINE FILTER
COIL,DEGAUSS
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
CORE,FERRITE
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
100 UH
100 UH
4.7 MH
ELH5L4113
D8000012
1R5A472F24
8R200024
1.2 UH
100 UH
1.2 UH
22 UH
100 UH
100 UH
3.3 UH
33 UH
W5T29X7.5X19
82 UH
82 UH
820 UH
150 UH
15 UH
10 UH
2.2 UH
22 UH
100 UH
22 UH
47 UH
ELECTRICAL REPLACEMENT PARTS LIST
Location No.
TSB P/N
Reference No.
COILS & TRANSFORMERS
L4006
L4007
L4008
L4009
L4205
L5501
L5503
L5504
L5505
L5506
T401
! T501
T4001
BZ310040
BZ310024
BZ310002
BZ310039
BZ310002
BZ310002
BZ310071
BZ310039
BZ310039
BZ310041
BZ310072
BZ310073
BZ310114
02167F470J
0326230038
021673101K
02167F220J
021673101K
021673101K
021LA6820K
02167F220J
02167F220J
02167F101J
045013001J
0481350524
031626009R
! J351
J701
! J801
J4201
J4202
BZ614002
BZ614114
BZ614115
BZ614203
BZ614204
060G131014
0602431013
066C130017
060Q431018
060Q411015
SW751
SW791
SW792
SW793
SW794
SW795
SW796
SW797
SW798
SW799
SW1001
BZ612010
BZ612010
BZ612010
BZ612010
BZ612010
BZ612010
BZ612010
BZ612010
BZ612010
BZ612010
BZ612002
0504101T34
0504101T34
0504101T34
0504101T34
0504101T34
0504101T34
0504101T34
0504101T34
0504101T34
0504101T34
0508221001
VR401
VR402
VR404
VR502
BZ210101
BZ210101
BZ210068
BZ210109
V1163H4BTC
V1163H4BTC
V1163Q3BTC
V1163Q2BTC
PCB010
PCB030
PCB070
PCB110
PCB330
PCB550
BZ610247
BZ610228
BZ610229
BZ610230
BZ610231
BZ610053
A59501Q010
A59504B030
A59504B070
A59504B110
A59504B330
A4C831B550
B301
B502
B504
B505
BL001
CD355
CD356
! CD501
CD601
CD702
CD757
CD802
CD803
CD805
CD810
CD820
CF601
CF603
CF604
! CP401
CP402
! CP502
CP602
CP604
CP801
CP802
CP805
CY901
CD1002
CD4203
CD4206
CP1004
CP1005
BZ310121
BZ310122
BZ310121
BZ310122
BZ310014
BZ614205
BZ614205
BZ614197
BZ614059
BZ614206
BZ614207
BZ614122
BZ614233
BZ614267
BZ614210
BZ614211
BZ613014
BZ613015
BZ613016
BZ614020
BZ614016
BZ614283
BZ614039
BZ614284
BZ614058
BZ614269
BZ614212
BZ614285
BZ614198
BZ614124
BZ614060
BZ614010
BZ614086
024HT03553
024HT03563
024HT03553
024HT03563
023C00022A
06CU123201
06CU123201
1207414905
06CH01006A
06CU2B2801
06CU2A2501
06CP82035A
122Y054501
122Y054403
122Y094001
122Y0D2501
1022T45R72
1011T4R504
1011T4R517
069X450029
069W01001A
069S420110
069E270129
069J160048
069W010010
069S320010
069R250589
069J160038
122F071901
06CH01812A
06CH01388A
0697280590
069J770029
Description
COIL
COIL,TRAP
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
TRANS,HORIZONTAL DRIVE
TRANSFORMER,SWITCHING
COIL,BIAS OSC
47 UH
2623003
100 UH
22 UH
100 UH
100 UH
82 UH
22 UH
22 UH
100 UH
5013001
81350524
1626009
JACKS
RCA JACK
RCA JACK
SOCKET,CATHODE RAY TUBE
RCA JACK
RCA JACK
HTJ-035-28A
JPJ1187-010010
CVT3275-5101
AV3-19DS-1
AV3-19D-1
SWITCHES
SWITCH,TACT
SWITCH,TACT
SWITCH,TACT
SWITCH,TACT
SWITCH,TACT
SWITCH,TACT
SWITCH,TACT
SWITCH,TACT
SWITCH,TACT
SWITCH,TACT
SWITCH (LEAF)
EVQ21505R
EVQ21505R
EVQ21505R
EVQ21505R
EVQ21505R
EVQ21505R
EVQ21505R
EVQ21505R
EVQ21505R
EVQ21505R
SPVF130100
VARIABLE RESISTORS
VOLUME,SEMI FIXED
VOLUME,SEMI FIXED
VOLUME,SEMI FIXED
VOLUME,SEMI FIXED
EVNCYAA03BE4
EVNCYAA03BE4
EVNCYAA03BQ3
EVNCYAA03BQ2
P.C.BOARD ASSEMBLIES
PCB ASS'Y
VMA214A
PCB ASS'Y
TEXA33C
PCB ASS'Y
TMA506A
PCB ASS'Y
TCA362A
PCB ASS'Y
VEA943A
SEE CHASSIS REPLACEMENT PARTS LIST
MISCELLANEOUS
CORE,BEADS
CORE,BEADS
CORE,BEADS
CORE,BEADS
COIL BALUN
CORD,CONNECTOR
CORD,CONNECTOR
CORD,AC BUSH
CORD,CONNECTOR
CORD,CONNECTOR
CORD,CONNECTOR
CORD,CONNECTOR
CORD,JUMPER
CORD,JUMPER
CORD,JUMPER
CORD,CONNECTOR
FILTER,SAW
FILTER,CERAMIC
FILTER,CERAMIC
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
CORD,JUMPER
CORD, EIS CONNECTOR
CORD, EIS CONNECTOR
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
W5RH3.5X5X1.0
W4BRH3.5X6X1.0X2
W5RH3.5X5X1.0
W4BRH3.5X6X1.0X2
HPN-01
CU123201
CU123201
7414905
CH01006A
CU2B2801
CU2A2501
CP82035A
2Y054501
2Y054403
2Y094001
2Y0D2501
SAF45MFY220ZR
EFCT4R5YS5A
EFCT4R5MW5
B05B-DVS
003P-2100
A1561WV2-2P
8283_0712_00_000
IMSA-9130S-06L
005P-2100
A2361WV2-2P
52147-0510
IMSA-9130B-06
2F071901
CH01812A
CH01388A
TMC-J08P-B1
IMSA-9604S-07Z14
ELECTRICAL REPLACEMENT PARTS LIST
!
!
!
!
!
!
!
!
Location No.
TSB P/N
CP1006
CP4001
CP4002
CP4003
CP4201
CP4202
CP803A
CP803B
CP805B
CP810A
CP810B
CP820A
CP820B
CUS012
CUS013
BZ614014
BZ614011
BZ614050
BZ614009
BZ614213
BZ614214
BZ614006
BZ614006
BZ614215
BZ614216
BZ614217
BZ614218
BZ614219
BZ710148
BZ710149
BZ710002
BZ614043
BZ614044
BZ614125
BZ614126
BZ310131
BZ614005
BZ614005
BZ614005
BZ614005
BZ614127
BZ614016
BZ614016
BZ614253
BZ614253
BZ410079
BZ614221
BZ610125
BZ614130
BZ613004
BZ613002
BZ613006
BZ613017
069J740029
0697290620
069J760029
0697120320
069S2A0629
069S2B0629
067R105019
067R105019
067R005019
069R290589
067R009019
069R2D0589
067R013019
800WFAA007
800WFAA008
800WF00019
124116281A
124120301A
081PC6R304
081PC2R504
043221017R
06710T0006
06710T0006
06710T0006
06710T0006
077Q000019
069W01001A
069W01001A
070W546003
070W546003
DF5EL3R0A0
076N0DQ040
0145K00055
098W210419
100CT3R505
100CT01207
100DA32R01
100CT3R502
RC...................
CARBON RESISTOR
CC...................
CE...................
CP...................
CPP..................
CPL..................
CMP...................
CMPL................
CMPP................
CERAMIC CAPACITOR
ALUMI ELECTROLYTIC CAPACITOR
POLYESTER CAPACITOR
POLYPROPYLENE CAPACITOR
PLASTIC CAPACITOR
METAL POLYESTER CAPACITOR
METAL PLASTIC CAPACITOR
METAL POLYPROPYLENE CAPACITOR
EL001
EL002
F501
F502
FB401
FH501
FH502
FH503
FH504
OS753
PH001
PH002
SP351
SP352
TH501
TM101
TU601
V801
X602
X1001
X1002
X4001
Reference No.
MISCELLANEOUS
Description
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
WIRE HOLDER
WIRE HOLDER
WIRE HOLDER
CONNECTOR PCB SIDE
WIRE HOLDER
CONNECTOR PCB SIDE
WIRE HOLDER
CUSHION B
CUSHION C
CUSHION-C
EYE LET
EYE LET
FUSE
FUSE
TRANSFORMER,FLYBACK
HOLDER,FUSE
HOLDER,FUSE
HOLDER,FUSE
HOLDER,FUSE
REMOTE RECEIVER
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
SPEAKER
SPEAKER
DEGAUSS ELEMENT
TRANSMITTER
TUNER,VHF-UHF
CRT W/DY
CRYSTAL
CRYSTAL
CRYSTAL
CRYSTAL
RESISTOR
CAPACITORS
IMSA-9604S-04Z14
TOC-C09X-A1
IMSA-9604S-06Z14
TMC-T02X-E1
A2001WV2-10P
A2001WV2-11P
51052-0500
51052-0500
51048-0510
52147-0910
51048-0910
52147-1310
51048-1310
or
XRY16X28BD
XRY20X30BD
51MS063LCC
51MS025LCC
3221017R
EYF-52BC
EYF-52BC
EYF-52BC
EYF-52BC
PIC-28143TC5
003P-2100
003P-2100
MSF-18D5SB05-02
MSF-18D5SB05-02
ZPB45BL3R0A
VC-FL20S
TECC1040PG32D
A51LSH196X01(O)
HC-49/C
HC-49/U-S
DT-26
HC-49/U
TOSHIBA VIDEO PRODUCTS PTE. LTD.
438B ALEXANDRA ROAD, BLOCK B #06-01 ALEXANDRA TECHNOPARK SINGAPORE 119968
Download PDF
Similar pages