X-CM32BTD-K/-W X-CM325BTD-W X-CM42BTD-K - S-bol

X-CM32_VXE8_En.book
1 ページ
年
月
日 水曜日 午後
時
分
X-CM32BTD-K/-W
X-CM325BTD-W
X-CM42BTD-K/-W
CD Receiver System
Discover the benefits of registering your product online at
http://www.pioneer.co.uk (or http://www.pioneer.eu).
Operating Instructions
X-CM32_VXE8_En.book
2 ページ
年
月
日 水曜日 午後
CAUTION
TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
D3-4-2-1-1_B1_En
WARNING
This equipment is not waterproof. To prevent a fire or
shock hazard, do not place any container filled with
liquid near this equipment (such as a vase or flower
pot) or expose it to dripping, splashing, rain or
moisture.
時
分
CAUTION
The STANDBY/ON switch on this unit will not
completely shut off all power from the AC outlet.
Since the power cord serves as the main disconnect
device for the unit, you will need to unplug it from the
AC outlet to shut down all power. Therefore, make
sure the unit has been installed so that the power
cord can be easily unplugged from the AC outlet in
case of an accident. To avoid fire hazard, the power
cord should also be unplugged from the AC outlet
when left unused for a long period of time (for
example, when on vacation).
D3-4-2-2-2a*_A1_En
D3-4-2-1-3_A1_En
WARNING
To prevent a fire hazard, do not place any naked flame
sources (such as a lighted candle) on the equipment.
CAUTION
This product is a class 1 laser product classified
under the Safety of laser products, IEC 60825-1:2007.
D3-4-2-1-7a_A1_En
CLASS 1 LASER PRODUCT
VENTILATION CAUTION
When installing this unit, make sure to leave space
around the unit for ventilation to improve heat radiation
(at least 25 cm at top, 15 cm at rear, and 5 cm at each
side).
WARNING
Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the product,
and to protect it from overheating. To prevent fire
hazard, the openings should never be blocked or
covered with items (such as newspapers, table-cloths,
curtains) or by operating the equipment on thick carpet
or a bed.
D3-4-2-1-7b*_A1_En
D58-5-2-2a_A1_En
This product is for general household purposes. Any
failure due to use for other than household purposes
(such as long-term use for business purposes in a
restaurant or use in a car or ship) and which requires
repair will be charged for even during the warranty
period.
K041_A1_En
POWER-CORD CAUTION
Handle the power cord by the plug. Do not pull out the
plug by tugging the cord and never touch the power
cord when your hands are wet as this could cause a
short circuit or electric shock. Do not place the unit, a
piece of furniture, etc., on the power cord, or pinch the
cord. Never make a knot in the cord or tie it with other
cords. The power cords should be routed such that they
are not likely to be stepped on. A damaged power cord
can cause a fire or give you an electrical shock. Check
the power cord once in a while. When you find it
damaged, ask your nearest PIONEER authorized
service center or your dealer for a replacement.
S002*_A1_En
Operating Environment
Operating environment temperature and humidity:
+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH
(cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in
locations exposed to high humidity or direct sunlight (or
strong artificial light)
D3-4-2-1-7c*_A1_En
X-CM32_VXE8_En.book
3 ページ
年
月
日 水曜日 午後
時
分
Information for users on collection and disposal of old equipment and used batteries
Symbol for
equipment
These symbols on the products, packaging, and/or accompanying documents mean
that used electrical and electronic products and batteries should not be mixed with
general household waste.
For proper treatment, recovery and recycling of old products and used batteries,
please take them to applicable collection points in accordance with your national
legislation.
Symbol examples
for batteries
By disposing of these products and batteries correctly, you will help to save valuable
resources and prevent any potential negative effects on human health and the
environment which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products and batteries,
please contact your local municipality, your waste disposal service or the point of sale
where you purchased the items.
These symbols are only valid in the European Union.
Pb
For countries outside the European Union:
If you wish to discard these items, please contact your local authorities or dealer and
ask for the correct method of disposal.
K058a_A1_En
Radio wave caution
WARNING
This unit uses a 2.4 GHz radio wave frequency, which is
a band used by other wireless systems (Microwave
ovens and Cordless phones, etc.). In this event noise
appears in your television image, there is the possibility
this unit (including products supported by this unit) is
causing signal interference with the antenna input
connector of your television, video, satellite tuner, etc. In
this event, increase the distance between the antenna
input connector and this unit (including products
supported by this unit).
• Pioneer is not responsible for any malfunction of the
compatible Pioneer product due to communication
error/malfunctions associated with your network
connection and/or your connected equipment.
Please contact your Internet service provider or
network device manufacturer.
• A separate contract with/payment to an Internet
service provider is required to use the Internet.
Store small parts out of the reach of children and
infants. If accidentally swallowed, contact a doctor
immediately.
X-CM32_VXE8_En.book
4 ページ
年
月
日 水曜日 午後
時
分
Thank you for buying this Pioneer product.
Please read through these operating instructions so that you will know how to operate your model properly. After you
have finished reading the instructions, put them in a safe place for future reference.
Contents
01 Before you start
07 USB playback
What’s in the box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Loading the batteries in the remote control . . . . . . . . . . . . . .5
Using the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Playing USB storage devices . . . . . . . . . . . . . . . . . . . . . . . . .23
Repeat play. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Random play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Specify the folder to play. . . . . . . . . . . . . . . . . . . . . . . . . . 24
Switch the display contents . . . . . . . . . . . . . . . . . . . . . . . 24
Playing in the desired order (Programmed Play) . . . . . . . . .24
02 Part names and functions
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Speaker system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Detatching and replacing the front grille . . . . . . . . . . . . . . . .7
Attaching the Non-skid pads . . . . . . . . . . . . . . . . . . . . . . . 8
Rotating the Speaker Badge . . . . . . . . . . . . . . . . . . . . . . . 8
Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Top panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
03 Connections
Speaker connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Connecting antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Using external antennas. . . . . . . . . . . . . . . . . . . . . . . . . . 12
Plugging in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
04 Getting started
To turn the power on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
General control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Input function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Display brightness control . . . . . . . . . . . . . . . . . . . . . . . . 13
Volume auto set-in. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Volume control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Muting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Sound controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Equalizer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
P.bass control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Bass/treble control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Setting the wake-up timer . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Calling the wake-up timer. . . . . . . . . . . . . . . . . . . . . . . . . 15
Cancelling the wake-up timer. . . . . . . . . . . . . . . . . . . . . . 15
Using the wake-up timer. . . . . . . . . . . . . . . . . . . . . . . . . . 15
Using the sleep timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Using Headphones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
05 iPod/iPhone/iPad playback
Confirming what iPod/iPhone/iPad models are
supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Connecting your iPod/iPhone/iPad . . . . . . . . . . . . . . . . . . . .16
Connecting iPod/iPhone to the top panel
(X-CM42BTD only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Close the iPod/iPhone connector port
(X-CM42BTD only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Connecting iPod/iPhone/iPad using supplied stand. . . . 17
Playing iPod/iPhone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Playing iPad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
06 Disc playback
Playing discs or files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Advanced CD or MP3/WMA disc playback . . . . . . . . . . . . . .20
Direct track search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Repeat play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Random play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Programmed play (CD or MP3/WMA) . . . . . . . . . . . . . . . 21
About downloading MP3/WMA . . . . . . . . . . . . . . . . . . . . 21
About folder playback order . . . . . . . . . . . . . . . . . . . . . . . 21
Specify the folder to play. . . . . . . . . . . . . . . . . . . . . . . . . . 22
Switch the display contents . . . . . . . . . . . . . . . . . . . . . . . 22
4
En
08 Using the tuner
Listening to the radio broadcasts . . . . . . . . . . . . . . . . . . . . . .25
Tuning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Saving station presets. . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
To recall a memorised station . . . . . . . . . . . . . . . . . . . . . 26
To scan the preset stations. . . . . . . . . . . . . . . . . . . . . . . . 26
To erase entire preset memory. . . . . . . . . . . . . . . . . . . . . 26
Using the Radio Data System (RDS) . . . . . . . . . . . . . . . . . . .26
An introduction to RDS. . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Searching for RDS programs . . . . . . . . . . . . . . . . . . . . . . 26
Information provided by RDS . . . . . . . . . . . . . . . . . . . . . . 27
Using the Auto Station program Memory (ASPM). . . . . 27
Notes for RDS operation . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Listening to the DAB+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
About DAB+ (Digital Audio Broadcasting) . . . . . . . . . . 28
Auto Scan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Selecting a station in the station list . . . . . . . . . . . . . . . . 28
Manual tune. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Changing the information display . . . . . . . . . . . . . . . . . . 29
Memorising a station . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
DAB Frequency table (BAND III) . . . . . . . . . . . . . . . . . . . 29
09 Other connections
Connecting auxiliary components . . . . . . . . . . . . . . . . . . . . .30
10 Bluetooth® Audio playback
Music playback using Bluetooth wireless technology . . . . .31
Remote control operation . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Pairing with the unit (Initial registration) . . . . . . . . . . . . . . . .31
Listen to music on the unit from a Bluetooth capable
device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
BT STANDBY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Radio wave caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Scope of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Radio wave reflections . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Precautions regarding connections to products
supported by this unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
11 Additional information
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Playable discs and formats . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Regarding copy protected CDs . . . . . . . . . . . . . . . . . . . . 36
Supported audio file formats . . . . . . . . . . . . . . . . . . . . . . 36
Cautions on use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
When moving this unit . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Place of installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Do not place objects on this unit . . . . . . . . . . . . . . . . . . . 37
About condensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Cleaning the product. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Cleaning the lens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Handling discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Storing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Cleaning discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
About specially shaped discs . . . . . . . . . . . . . . . . . . . . . . 38
About iPod/iPhone/iPad . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Auto power off setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Restoring all the settings to the defaults . . . . . . . . . . . . . . . .38
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
X-CM32_VXE8_En.book
5 ページ
年
月
日 水曜日 午後
時
分
Before you start
01
English
Chapter 1:
Before you start
Loading the batteries in the
remote control
1 Open the rear lid and load the batteries as
illustrated below.
Español
Please confirm that the following accessories are in the box
when you open it.
• Remote Control
• AAA batteries (R03) x 2
• Power cord
• Speaker wire x 2
• DAB/FM wire antenna
• Non-skid pads x 8
• iPhone/iPad stand
• Warranty card
• Operating instructions (this document)
• Do not heat batteries, disassemble them, or throw them
into flames or water.
• Batteries may have different voltages, even if they are the
same size and shape. Do not use different types of
batteries together.
• To prevent leakage of battery fluid, remove the batteries
if you do not plan to use the remote control for a long
period of time (1 month or more). If the fluid should leak,
wipe it carefully off the inside of the case, then insert
new batteries. If a battery should leak and the fluid
should get on your skin, flush it off with large quantities
of water.
• When disposing of used batteries, please comply with
governmental regulations or environmental public
institution’s rules that apply in your country/area.
Français
What’s in the box
WARNING
• Do not use or store batteries in direct sunlight or other
excessively hot place, such as inside a car or near a
heater. This can cause batteries to leak, overheat,
explode or catch fire. It can also reduce the life or
performance of batteries.
Using the remote control
The remote has a range of about 7 m at an angle of about 30º
from the remote sensor.
30°
30°
STAND
CD

iPod
USB
E
AUDIO
TIMER

2
/CLOS
CLOCK/
TUNER
OPEN
AUDIO
1
BT
5
6
ER
EQUALIZ
AY
SLEEP
3
IN
8
DISPL
CLEAR
7
S
BASS/TR
T
EBLE
T
+
NO

R
+
DAB
ASPM
DIMME
E
VOLUM
RDS
RY
MEMO RAM
/PROG
MUTE
ST/MO

TUNE–
–

R
FOLDE
OM
R
ENTE
PRESE
RAND
MENU
TUNE+
REPEA
9
P.BAS
0
PTY
–

SCAN
Y
DISPLA
Y
DISPLA


ENTER
CAUTION
• Do not use any batteries other than the ones specified.
Also, do not use a new battery together with an old one.
• When inserting the batteries, make sure not to damage
the springs on the battery’s  terminals. This can cause
batteries to leak or over heat.
• When loading the batteries into the remote control, set
them in the proper direction, as indicated by the polarity
marks ( and ).
BY/ON
Close the rear lid.
4
2
7m
Keep in mind the following when using the remote control:
• Make sure that there are no obstacles between the
remote and the remote sensor on the unit.
• Remote operation may become unreliable if strong
sunlight or fluorescent light is shining on the unit’s
remote sensor.
• Remote controllers for different devices can interfere
with each other. Avoid using remotes for other
equipment located close to this unit.
• Replace the batteries when you notice a fall off in the
operating range of the remote.
5
En
X-CM32_VXE8_En.book
02
6 ページ
年
月
日 水曜日 午後
時
分
Part names and functions
Chapter 2:
Part names and functions
1
Remote control
2
1
2
STANDBY/ON
OPEN/CLOSE


CD
USB
TUNER
AUDIO IN
iPod
BT AUDIO
CLOCK/TIMER
SLEEP
2
3
3
iPod (X-CM42BTD only)
12
Use to switch between the iPod controls and the receiver
controls (page 16).
BT AUDIO
Use to play the audio file using the Bluetooth network
(page 31).
3
P.BASS
4
4
5
6
7
8
9
13
CLEAR
RANDOM
0
FOLDER
TUNE+
SLEEP
See Using the sleep timer on page 15.
REPEAT
DISPLAY
CD Receiver control buttons
CLOCK/TIMER
Use for setting the clock, as well as for setting and
checking the timers (page 13).
BASS/TREBLE
5
Input function buttons
Use to select the input source to this receiver (page 19).
EQUALIZER
1
 STANDBY/ON
Switches the receiver between standby and on (page 19).
14
4
15
Use to enter the number (page 20).
5
6
Numeric buttons (0 to 9)
CLEAR
Use to clear the programmed play (page 21).
6
7
ENTER
Press to change the display for songs playing back from
CD or USB (page 22).
MEMORY
/PROGRAM
MENU
CD Receiver control buttons
DISPLAY
FOLDER
PRESET
+
+
8
–

Use to access the menu.
–
DIMMER

10
MENU
16
MUTE
9
Use to select the folder of the MP3/WMA disc or USB
mass storage device (page 21).
VOLUME
TUNE–

ST/MONO RDS ASPM
MEMORY/PROGRAM



PTY
DISPLAY
11
DAB SCAN ENTER
DISPLAY
17
Use to memory or program the MP3/WMA disc
(page 21).
7
/// (TUNE +/–), ENTER
Use to select/switch system settings and modes, and to
confirm actions.
Use TUNE +/– can be used to find radio frequencies
(page 25).
8
PRESET control buttons
Use to select preset radio stations (page 25).
9
MUTE
Mutes/unmutes the sound (page 13).
6
En
X-CM32_VXE8_En.book
7 ページ
年
月
日 水曜日 午後
時
分
Part names and functions
02
10 Playback control buttons
Speaker system
11 Tuner control buttons
ST/MONO
Use to switch the sound mode between stereo and
monaural. (page 25)
3
2
4
Use to search for RDS Auto station program memory
(page 26).
1
Tweeter
Use to search for RDS program types (page 26).
2
Woofer
RDS DISPLAY
3
Bass Reflex Duct
Press to change the RDS display for information mode
(page 26).
4
Speaker Terminals
DAB SCAN
Use to scan for DAB radio station (page 28).
DAB ENTER
Use to confirm the DAB radio station (page 28).
DAB DISPLAY
Press to change the DAB display for information mode
(page 29).
12 OPEN/CLOSE
Use to open or close the disc tray (page 19).
13 Sound control buttons
Adjust the sound quality (page 14).
Important
Español
RDS PTY
Français
RDS ASPM
1
English
Use to control each function after you have selected it using
the input function buttons (page 19).
• Speaker grille can be removed.
• Make sure nothing comes into contact with the speaker
diaphragms when you remove the speaker grilles.
• Both speakers can be used on either the right or the left
side.
Detatching and replacing the front
grille
The front grille of this speaker system is removable. Proceed
as follows:
14 RANDOM
Press to randomize order play setting from a CD, iPod or USB
(page 20).
15 REPEAT
Press to change the repeat play setting from a CD, iPod or
USB (page 20).
16 Volume control buttons
Use to set the listening volume (page 13).
17 DIMMER
Dims or brightens the display. The brightness can be
controlled in four steps (page 13).
1 Grab the bottom of the grille, and gently
pull it toward you to remove the bottom
portion.
2 Next, grab the top part of the grille and
gently pull it toward you to remove the top
portion.
To install the grille, align the projections on the speaker with
the receptacles on the top and at the base of the grille and
push them into place.
7
En
X-CM32_VXE8_En.book
02
8 ページ
年
月
日 水曜日 午後
時
分
Part names and functions
Attaching the Non-skid pads
Rotating the Speaker Badge
Apply the accessory non-skid pads to the bottom surfaces of
the speakers.
The grill frame speaker badge can be rotated. Operate as
follows.
Important
• Use the speaker is usually in an upright position.
When placing speakers upright
1 Grasp the speaker badge (1), pull forward
(2), and turn left (3).
The speaker badge will rotate.
When placing the speakers vertically upright, attach the nonskid pads to the bottom surface of the speakers.
3
The bottom surface
of the speaker
2
1
If the speaker badge does not rotate doing the above step 1,
try the following steps 2 to 3.
When placing speakers horizontally
2
Detach the speaker grill.
When placing the speaker horizontally, attach the non-skid
pads to what will be the bottom surface of the speakers.
The bottom surface of
the speaker when
using it horizontally
3 Rotate the screws on the backside of the grill
in a clockwise direction using a plus driver.
Backside of speaker grill
Important
• Do not rotate the screw in a counter-clockwise direction
as it may cause the badge to fall off.
8
En
X-CM32_VXE8_En.book
9 ページ
年
月
日 水曜日 午後
時
分
Part names and functions
02
1
2
English
Front panel
3
Français
PHONES
AUDIO IN
4
5
1
Main display
2
Volume control
6
Use to set the listening volume (page 13).
3
Volume illumination
Light when the power on.
4
Headphone socket
Use to connect headphones. When the headphones are
connected, there is no sound output from the speakers.
5
AUDIO IN socket
7
8
6
VOLUME
Español
TIMER
9
Remote sensor
Receives the signals from the remote control.
7
Disc tray
Place the disc, label side up (page 19).
8
TIMER indicator
Lights when the receiver is power off with timer setting.
9
USB terminal
Use to connect your USB mass storage device or Apple iPod/
iPhone/iPad as an audio source (page 23).
Use to connect an auxiliary component using a stereo
minijack cable (page 30).
9
En
X-CM32_VXE8_En.book
02
10 ページ
年
月
日 水曜日 午後
時
分
Part names and functions
Top panel
1
PUSH OPEN

STANDBY/ON

2
1
iPod/iPhone connector port
(X-CM42BTD only)
To connect the iPod/iPhone, press the PUSH OPEN tab
(page 17).
2
 STANDBY/ON
Switches the receiver between standby and on (page 19).
3
Playback control buttons
Selects the desired track or file to be played back. Use to stop
the playback. Stops playback or resumes playback from the
pause point.
10
En



3
4
INPUT

4
5
INPUT
Selects the input source.
Long press to change to BT STANDBY settings.
5
Disc tray open/close button
Use to open or close the disc tray (page 19).
X-CM32_VXE8_En.book
11 ページ
年
月
日 水曜日 午後
時
分
Connections
03
English
Chapter 3:
Connections
Speaker connection
Left
speaker
Right
speaker
This unit’s rear panel
Español
• Push open the tabs and insert exposed wire.
• The provided speaker wire with red tube is for the (+)
terminal. Connect the wire with red tube the (+)
terminal, and other wire to the (–) terminal.
• Both speakers can be used on either the right or the left
side.
• Do not connect the supplied speakers to any amplifier
other than the one supplied with this system.
Connection to any other amplifier may result in
malfunction or fire.
• Do not attach these speakers to the wall or ceiling.
They may fall off and cause injury.
• Do not install your speakers overhead on the ceiling or
wall. The grill is designed to be detachable, and as
such it may fall and cause damage or personal injury if
installed overhead.
• These speakers are magnetically shielded. However,
depending on the installation location, color distortion
may occur if the speaker system is installed extremely
close to the screen of a television set. If this happens,
turn off the television set, and then turn it on after 15 to
30 minutes. If the problem persists, move the speaker
system away from the television set.
• Make sure that the speaker cable cores do not become
exposed and make contact with other cable cores. This
may cause malfunction of the product.
• Do not allow the speaker cable core to come into contact
with the receiver body.
Français
CAUTION
• Be sure to turn off the power and unplug the power cord
from the power outlet whenever making or changing
connections.
• Connect the power cord after all the connections
between devices have been completed.
SPEAKERS
ANTENNA
LINE
AC IN
IN
DAB/FM
R
R
L
L
1
2
• If the speaker cable core comes into contact with any
metal portion of the receiver’s body, it may damage the
speakers and cause smoke and fire.
Insert speaker cables securely into the terminals and
check that the cable does not come out of easily.
Red tube
Supplied
speaker wire
Note
• There is no difference between L and R speakers.
CAUTION
• These speaker terminals carry HAZARDOUS LIVE
voltage. To prevent the risk of electric shock when
connecting or disconnecting the speaker cables,
disconnect the power cord before touching any
uninsulated parts.
• Do not connect any speakers other than those supplied
to this system.
11
En
X-CM32_VXE8_En.book
03
12 ページ
年
月
日 水曜日 午後
時
分
Connections
Connecting antennas
Plugging in
• Connect the DAB/FM wire antenna as shown below.
• To improve reception and sound quality, connect
external antennas (see Using external antennas).
Before making or changing the connections, switch off the
power and disconnect the power cord from the AC outlet.
After you’ve finished making all connections, plug the unit
into an AC outlet.
This unit’s rear panel
SPEAKERS
LINE
AC IN
IN
R
L
R
L
ANTENNA
Power cord
To AC outlet
DAB/FM
1 Connect the DAB/FM wire antenna into the
DAB/FM antenna socket.
For best results, extend the DAB/FM antenna fully and fix to a
wall or door frame. Don’t drape loosely or leave coiled up.
Using external antennas
To improve DAB/FM reception
Use a PAL connector (not supplied) to connect an external
DAB/FM antenna.
One-touch PAL
connector
ANTENNA
75 coaxial
cable
12
En
DAB/FM
CAUTION
• Do not use any power cord other than the one supplied
with this unit.
• Do not use the supplied power cord for any purpose
other than that described above.
X-CM32_VXE8_En.book
13 ページ
年
月
日 水曜日 午後
時
分
Getting started
04
English
Chapter 4:
Getting started
General control
Press the  STANDBY/ON to turn the power on.
After use:
Input function
Press the  STANDBY/ON to enter the power stand-by mode.
When the INPUT on main unit is pressed, the current function
will change to different mode. Press the INPUT repeatedly to
select desired function.
Note
CD
LINE
DAB
FM
AUDIO IN
Setting the clock
STANDBY/ON
OPEN/CLOSE


CD
iPod
USB
TUNER
CLOCK/TIMER
DISPLAY
TUNE+
FOLDER
Display brightness control
SLEEP
MENU
2
IPOD
Press DIMMER to dims the display brightness. The
brightness can be controlled in four steps.
AUDIO IN
MEMORY
/PROGRAM
EQUALIZER
1
BT AUDIO
(X-CM42BTD only)
ENTER
BT AUDIO
USB/IPOD
Español
• In standby mode, if iPod/iPhone/iPad is connected, the
unit turns charge mode.
Français
To turn the power on
3
Volume auto set-in
1
Press  STANDBY/ON to turn the power on.
If you turn off and on the main unit with the volume set to 31
or higher, the volume starts at 30 and sets in to the last set
level.
2
Press CLOCK/TIMER on the remote control.
Volume control
P BASS
“CLOCK” is shown on the main display.
3
Press ENTER.
4
Press / to set the day, then press ENTER.
5 Press / to set the hour, then press
ENTER.
6 Press / to set the minute, then press
ENTER to confirm.
7 Press ENTER.
To confirm the time display:
Press the CLOCK/TIMER. The time display will appear for
about 10 seconds.
To readjust the clock:
Turn the volume knob towards VOLUME (on main unit) or
press VOLUME +/– (on remote control) to increase or
decrease the volume.
CAUTION
• The sound level at a given volume setting depends on
speaker efficiency, location, and various other factors. It
is advisable to avoid exposure to high volume levels. Do
not turn the volume on to full at switch on. Listen to
music at moderate levels. Excessive sound pressure
from earphones and headphones can cause hearing
loss.
Muting
The volume is muted temporarily when pressing the MUTE on
the remote control. Press again to restore the volume.
Perform “Setting the clock” from step 1.
Note
• When power supply is restored after unit is plugged in
again or after a power failure, reset the clock.
13
En
04_Getting_started_X-CM32.fm
04
14 ページ
4年4月8日 火曜日 午後8時
Getting started
Sound controls
Setting the wake-up timer
Equalizer
Used to change the existing timer setting, or to set a new
timer.
When the EQUALIZER is pressed, the current mode setting
will be displayed. To change to a different mode, press the
EQUALIZER repeatedly until the desired sound mode
appears.
FLAT
A flat and basic sound
Press  STANDBY/ON to turn the power on.
2
Press and hold CLOCK/TIMER.
3 Press / to select “ONCE” or “DAILY”,
then press ENTER.
ONCE – Once timer play works for one time only at a
preset time.
DAILY – Daily timer play works at the same preset time
and days of week.
A powerful sound that
emphasizes low and high tones
DIALOGUE
A sound that allows the radio or
vocals to be heard more easily
4 Press / to select “TIMER SET”, then
press ENTER.
NIGHT
A sound that can be enjoyed
at night even with lower volume
5 Press / to select the timer playback
source, then press ENTER.
CD, DAB, FM, USB/IPOD, IPOD (X-CM42BTD only), BT
AUDIO, AUDIO IN and LINE can be selected as the playback
source.
When the power is first turned on, the unit will enter the
P.bass mode which emphasises the bass frequencies. To
cancel the P.bass mode, press the P.BASS on the remote
control.
6 Press / to select the timer day, then
press ENTER.
Bass/treble control
7 Press / to set the hour, then press
ENTER.
Press the BASS/TREBLE, then press / to adjust the bass
or treble.
Note
• The EQUALIZER and P.BASS cannot operate
simultaneously. The most recently selected of these two
functions will be the one used.
• BASS/TREBLE can operate alongside either the
EQUALIZER or P.BASS.
When one of the above two functions is
selected, the function that is not selected will
be displayed as follows.
1
When P.BASS setting (ON/OFF) is changed
• EQUALIZER : FLAT
2
When EQUALIZER setting is changed
• P.BASS : OFF
En
1
ACTIVE
P.bass control
14
8分
8 Press / to set the minute, then press
ENTER.
Set the time to finish as in steps 7 and 8 above.
9 Adjust the volume press VOLUME +/– , then
press ENTER.
10 Press  STANDBY/ON to enter the power
standby mode.
The TIMER indicator lights up.
X-CM32_VXE8_En.book
15 ページ
年
月
日 水曜日 午後
時
分
Getting started
It can be used to re-use an existing timer setting.
Using Headphones
1 As well as steps 1 through 3 in “Setting the
wake-up timer”.
Connect to the jack plug of the headphones.
When the headphones are connected, there is no sound
output from the speakers.
Cancelling the wake-up timer
It can be used to turn off the timer setting.
1 As well as steps 1 through 3 in “Setting the
wake-up timer”.
TIMER
PHONES
VOLUME
AUDIO IN
Español
2 Press / to select “TIMER OFF”, then
press ENTER.
Using the wake-up timer
1 Press  STANDBY/ON to turn the power
off.
2 At the wake-up time, this unit will turn on
automatically and play the selected input
function.
Note
• If at the wake-up time iPod/iPhone/iPad is not connected
to this unit or a disc is not inserted, this unit will be
turned to on and not play back the track.
• If you set the timer, take one minute or more between the
start and end time.
Français
2 Press / to select “TIMER ON”, then press
ENTER.
English
Calling the wake-up timer
04
• Do not turn the volume on to full at switch on and listen
to music at moderate levels. Excessive sound pressure
from earphones and headphones can cause hearing
loss.
• Before plugging in or unplugging the headphone,
reduce the volume.
• Be sure your headphone has a 3.5 mm diameter plug
and impedance between 16  and 50 . The
recommended impedance is 32 .
Using the sleep timer
The sleep timer switches off the unit after a specified time so
you can fall asleep without worrying about it.
1 Press SLEEP repeatedly to select a switch off
time.
Choose between 10 min, 20 min, 30 min, 60 min, 90 min, 120
min, 150 min, 180 min or OFF. The newly set value displays for
5 seconds, and then the setting is completed.
Note
• After setting the sleep timer, pressing SLEEP will display
how much time is remaining.
• The sleep timer can be reset by pressing SLEEP while the
remaining time is displayed.
15
En
X-CM32_VXE8_En.book
05
16 ページ
年
月
日 水曜日 午後
時
分
iPod/iPhone/iPad playback
Chapter 5:
iPod/iPhone/iPad playback
Merely by connecting your iPod/iPhone/iPad to this unit, you
can enjoy high-quality sound from your iPod/iPhone/iPad.
Confirming what iPod/iPhone/iPad
models are supported
The iPod/iPhone/iPad playable on this unit are shown below.
iPod/iPhone/iPad
Lightning
connector
(X-CM42BTD only)
iPod nano 3G/4G/5G/6G
—

iPod nano 7G


iPod touch 1G/2G/3G/4G
—

iPod touch 5G


iPhone
—

iPhone 3G
—

iPhone 3GS
—

iPhone 4
—

iPhone 4s
—

iPhone 5


iPhone 5c


iPhone 5s


iPad mini
—

iPad mini with Retina
display
—

iPad
—

iPad 2
—

iPad (3rd generation)
—

iPad (4th generation)
—

iPad Air
—

USB Terminal
Note
• Pioneer does not guarantee that this unit plays iPod/
iPhone/iPad models other than the ones specified.
• Some functions may be restricted depending on the
model or software version.
• iPod/iPhone/iPad is licensed for reproduction of noncopyrighted materials or materials the user is legally
permitted to reproduce.
• Features such as the equalizer cannot be controlled
using this system, and we recommend switching the
equalizer off before connecting.
16
En
• Pioneer cannot under any circumstances accept
responsibility for any direct or indirect loss arising from
any inconvenience or loss of recorded material resulting
from iPod/iPhone/iPad failure.
• For detailed instructions on using the iPod/iPhone/iPad,
please refer to the manual supplied with the iPod/
iPhone/iPad.
• This system has been developed and tested for the
software version of iPod/iPhone/iPad indicated on the
website of Pioneer (http://pioneer.jp/homeav/support/
ios/eu/).
• Installing software versions other than indicated on the
website of Pioneer to your iPod/iPhone/iPad may result
in incompatibility with this system.
• This unit cannot be used to record CD, tuner or other
content on an iPod/iPhone/iPad.
Connecting your iPod/iPhone/iPad
CAUTION
• When connecting iPod/iPhone/iPad devices, use the
iPod/iPhone/iPad cable provided with iPod/iPhone/iPad
devices, or a commercially available iPod/iPhone/iPad
cable designed to support iPod/iPhone/iPad.
• An iPod/iPhone/iPad cable is not supplied with this unit.
Important
• If you are mounting the protective cover of a
commercially available iPod/iPhone/iPad, you may not
be able to connect iPod/iPhone/iPad to this unit.
X-CM32_VXE8_En.book
17 ページ
年
月
日 水曜日 午後
時
分
iPod/iPhone/iPad playback
1
Press the PUSH OPEN.
Close the iPod/iPhone connector port
(X-CM42BTD only)
• While pull the PULL CLOSE knob (1), close the iPod/
iPhone/iPad connector port firmly (2).
• When iPod/iPhone is not connected to the unit, close
the iPod/iPhone connector port firmly.
2
Open the iPod/iPhone connector port.
3
Connect your iPod/iPhone.
Español
1
Français
2
English
Connecting iPod/iPhone to the top
panel (X-CM42BTD only)
05
Connecting iPod/iPhone/iPad using
supplied stand
1 Connect the unit to an iPod/iPhone/iPad
with the iPod/iPhone/iPad cable.
iPod/iPhone/iPad
cable
17
En
X-CM32_VXE8_En.book
05
18 ページ
年
月
日 水曜日 午後
時
分
iPod/iPhone/iPad playback
2
Set up to stand the iPod/iPhone/iPad.
Playing iPad
When using an iPod/iPhone
Make sure the iPod/iPhone cable is aligned along the groove
for it on the back of the stand that comes with the unit.
Back of stand
1
Connect your iPad.
If an iPad is connected when this unit is on, playback of the
iPad will not begin.
2
Press USB as the input source.
“USB/IPOD” is shown on the main display.
3 When the recognition is completed, will
begin playing automatically.
CAUTION
• When your iPod/iPhone/iPad is connected to this unit
and you wish to operate the iPod/iPhone/iPad directly,
be sure to steady the iPod/iPhone/iPad with the other
hand to prevent malfunctions due to faulty contacts.
iPod/iPhone
cable
When using iPad
Make sure to place the iPad in a horizontal direction on the
stand.
Note
• iPod/iPhone/iPad recharging occurs whenever an iPod/
iPhone/iPad is connected to this unit. (This function is
supported in standby mode as well.)
• When input is switched from iPod to another function,
iPod/iPhone/iPad playback is temporarily stopped.
• When iPod/iPhone/iPad is not playing and no operations
have been performed for more than 20 minutes, the unit
will automatically power off.
• Auto power off can be switched to ON/OFF (page 38).
Important
Playing iPod/iPhone
1
Connect your iPod/iPhone.
If an iPod/iPhone is connected when this unit is on, playback
of the iPod/iPhone will not begin.
2
Press iPod or USB as the input source.
“IPOD” or “USB/IPOD” is shown on the main display.
3 When the recognition is completed, will
begin playing automatically.
18
En
• If this unit cannot play your iPod/iPhone/iPad, perform
the following troubleshooting checks:
- Check whether the iPod/iPhone/iPad is supported by
this unit.
- Reconnect the iPod/iPhone/iPad to the unit. If this
doesn’t seem to work, try resetting your iPod/iPhone/
iPad.
- Check the iPod/iPhone/iPad software is supported by
this unit.
• If the iPod/iPhone/iPad cannot be operated, check the
following items:
- Is the iPod/iPhone/iPad connected correctly?
Reconnect the iPod/iPhone/iPad to the unit.
- Is the iPod/iPhone/iPad experiencing a hangup? Try
resetting the iPod/iPhone/iPad, and reconnect it to the
unit.
06_DiscPlayback_X-CM32.fm
19 ページ
4年4月8日 火曜日 午後8時
分
Disc playback
06
English
Chapter 6:
Disc playback
MP3:
WMA:
WMA (Windows Media Audio) files are Advanced System
Format files that include audio files which are compressed
with Windows Media Audio codec. WMA is developed by
Microsoft as an audio format file for Windows Media Player.
• This system supports WMA (Sampling rates: 32 kHz/44.1
kHz/48 kHz; Bit rates: 64 kbps to 320 kbps).
• During VBR file playback, time counter in the display
may differ from its actual playback time.
Playing discs or files
1
Press  STANDBY/ON to turn the power on.
2 Press CD on the remote control or INPUT
repeatedly on the main unit to select CD input.
3
Press  OPEN/CLOSE to open the disc tray.
4
Place the disc on the disc tray, label side up.
Note
• Due to the structure of the disc information, it takes
longer to read an MP3/WMA disc than a normal CD
(approximately 20 to 90 seconds).
• When the beginning of the first track is reached during
fast reverse, the unit will enter the playback mode (only
for CD).
• If TV or radio interference occurs during CD operation,
move the unit away from the TV or radio.
Tip
• When no operation has done in CD mode and the audio
file is not played for more than 20 minutes, the power will
automatically turn off. In this case it is required that the
Auto power off is switched to ON.
• Auto power off can be switched to ON/OFF (page 38).
Various disc functions
Function
6
Press  to start playback.
Remote
control






Stop
Pause
Fast
forward/
reverse
Press  OPEN/CLOSE to close the disc tray.
Main
unit
Play
Track up/
down
5
Español
MP3 is a form of compression. It is an acronym which stands
for MPEG Audio Layer 3. MP3 is a type of audio code which is
processed by significant compression from the original audio
source with very little loss in sound quality.
• This system supports MPEG-1/2 Audio Layer 3 (Sampling
rates: 8 kHz to 48 kHz; Bit rates: 32 kbps to 320 kbps).
• During VBR file playback, time counter in the display
may differ from its actual playback time.
CAUTION
• Do not place two discs in one disc tray.
• Do not play discs of special shapes (heart, octagon, etc).
It may cause malfunctions.
• Do not push the disc tray whilst it is moving.
• If the power fails whilst the tray is open, wait until the
power is restored.
• Be sure to place 8 cm disc in the middle of the disc tray.
Français
This system can play back a standard CD, CD-R/RW in the CD
format and CD-R/RW with MP3 or WMA files, but cannot
record on them. Some audio CD-R and CD-RW discs may not
be playable due to the state of the disc or the device that was
used for recording.








Operation
Press in the stop mode.
Press in the playback mode.
Press in the playback mode.
Press  to resume
playback from the paused
point.
 Press in the playback or stop

mode.
If you press the button in the
stop mode, press  to
start the desired track.
 Press and hold down in the

playback mode.
Release the button to
resume playback.
After the last track is played, the unit will stop automatically.
19
En
X-CM32_VXE8_En.book
06
20 ページ
年
月
日 水曜日 午後
時
分
Disc playback
Advanced CD or MP3/WMA disc
playback
STANDBY/ON
OPEN/CLOSE


CD
USB
TUNER
AUDIO IN
iPod
BT AUDIO
CLOCK/TIMER
SLEEP
DISPLAY
FOLDER
TUNE+
MEMORY
/PROGRAM
MENU
EQUALIZER
2
4
5
PRESET
7
8
+
+
6
MUTE
–
9
REPEAT
VOLUME
TUNE–
BASS/TREBLE
CLEAR
RANDOM
0
To repeat one track:
Press REPEAT repeatedly until “RPT ONE” appears. Press
ENTER.
Press REPEAT repeatedly until “RPT ALL” appears. Press
ENTER.
To repeat desired tracks:
3
P.BASS
Repeat play can play one track, all tracks or a programmed
sequence continuously.
To repeat all tracks:
ENTER
1
Repeat play
–
DIMMER



ST/MONO RDS ASPM



PTY
DISPLAY
Direct track search
By using the numeric buttons, the desired tracks on the
current disc can be played.
Use the numeric buttons on the remote control to
select the desired track whilst playing the selected
disc.
Note
• A track number higher than the number of tracks on the
disc cannot be selected.
Perform steps 1 - 5 in “Programmed play” section on next
page and then press REPEAT repeatedly until “RPT ALL”
appears. Press ENTER.
To cancel repeat play:
Press REPEAT repeatedly until “RPT OFF” appears. Press
ENTER.
Note
• After performing repeat play, be sure to press .
Otherwise, the disc will play continuously.
• During repeat play, random play is not possible.
Random play
The tracks on the disc can be played in random order
automatically.
To random play all tracks:
To stop playback:
Press RANDOM repeatedly until “RDM ON” appears. Press
ENTER.
Press .
To cancel random play:
Press RANDOM repeatedly until “RDM OFF” appears. Press
ENTER.
Note
• If you press the  during random play, you can move
to the track selected next by the random operation.
• In random play, the unit will select and play tracks
automatically. (You cannot select the order of the
tracks.)
• During random play, repeat play is not possible.
20
En
X-CM32_VXE8_En.book
21 ページ
年
月
日 水曜日 午後
時
分
Disc playback
06
There are many music sites on the internet that you can
download MP3/WMA music files. Follow the instructions
from the website on how to download the music files. You can
then play back these downloaded music files by burning them
to a CD-R/RW disc.
• Your downloaded song/files are for personal use only.
Any other usage of the song without owner’s
permission, is against the law.
1 Whilst in the stop mode, press MEMORY/
PROGRAM on the remote control to enter the
programming save mode.
2 Press   or the numeric buttons on the
remote control to select the desired tracks.
3 Press ENTER to save folder and track
number.
• If you want to check the programmed tracks, press
MEMORY/PROGRAM.
• If you make a mistake, the last programmed tracks will
be canceled by pressing CLEAR.
5 Press  to start playback.
To cancel the programmed play mode:
To cancel the programmed play, press twice  on the remote
control. The display will show “PRG CLR” and all the
programmed contents will be cleared.
Adding tracks to the program:
Press the MEMORY/PROGRAM. Then follow steps 2 - 3 to
add tracks.
Note
• When a disc is ejected, the program is automatically
cancelled.
• If you press the  STANDBY/ON to enter the standby
mode or change the function from CD to another, the
programmed selections will be cleared.
• During the program operation, random play is not
possible.
If MP3/WMA files are recorded in several folders, a folder
number will be set to each folder automatically.
These folders can be selected by the FOLDER on the remote
control. If there is no supported file formats inside the
selected folder, the folder is skipped and the next folder will
be selected.
Example: How to set folder number if MP3/WMA format files
are recorded as below figure.
1
Español
4 Repeat steps 2 - 3 for other folder/tracks. Up
to 32 tracks can be programmed.
About folder playback order
Français
About downloading MP3/WMA
You can choose up to 32 selections for playback in the order
you like.
English
Programmed play (CD or MP3/WMA)
ROOT folder is set as folder 1.
2 As for folders inside ROOT folder (Folder A
and Folder B), the folder which is recorded
earlier on the disc will be set as folder 2 and
folder 3.
3 As for folder inside Folder A (Folder C and
Folder D), the folder which is recorded earlier on
the disc will be set as folder 4 and folder 5.
4 Folder E that is inside Folder D will be set as
folder 6.
• The folder and file order information which is recorded
on the disc depends on the writing software. There
maybe possibilities that this unit will playback the files
not according to our expected playback order.
• From a disc with MP3/WMA files up to 255 folders and
999 files (including non playable files) can be read.
ROOT
FOLDER A
(FOLDER 1) (FOLDER 2)
FOLDER B
(FOLDER 3)
FOLDER C
(FOLDER 4)
FILE 3
FILE 4
FILE 5
FOLDER D
(FOLDER 5)
FILE 6
FILE 7
FILE 8
FOLDER E
(FOLDER 6)
FILE 9
FILE 10
FILE 1
FILE 2
21
En
X-CM32_VXE8_En.book
06
22 ページ
年
月
日 水曜日 午後
Switch the display contents
Specify the folder to play, do the follwing steps.
STANDBY/ON
OPEN/CLOSE

DISPLAY
TUNE+
1
FOLDER

CD
USB
TUNER
iPod
BT AUDIO
CLOCK/TIMER
AUDIO IN
ENTER
SLEEP
MEMORY
/PROGRAM
MENU
EQUALIZER
1
2
3
P.BASS
4
5
6
7
8
9
PRESET
CLEAR
1
REPEAT
TUNE–
+
Title/Artist/Album display
–
Kind of file display
Number of folder/track
display
DIMMER
Press CD, and load an MP3/WMA disc.
2 Press FOLDER, and press / to select
desired playback folder.
3
Number of track, playback
time display
VOLUME
+
–
RANDOM
Press DISPLAY.
If the title, artist and album name has been written to the file,
that information will be displayed. (You can view this unit is
only alphanumeric characters. Non- alphanumeric character
are displayed in the ”*”.)
MUTE
BASS/TREBLE
Press ENTER.
Playback will start from the first song of the selected folder.
• In case of stop, press /, and the folder can be
selected.
En
分
Disc playback
Specify the folder to play
22
時
Note
• “Copyright protected WMA file” or “Not supported
playback file” can not be playback. In this case, will be
skipped automatically.
• There may be cases where no information can be
displayed.
• Displaying title, artist and album name is only supported
for MP3 files.
X-CM32_VXE8_En.book
23 ページ
年
月
日 水曜日 午後
時
分
USB playback
07
English
Chapter 7:
USB playback
Repeat play
1
Press USB as the input source.
To repeat one track:
Press REPEAT repeatedly until “RPT ONE” appears. Press
ENTER.
To repeat all tracks:
Press REPEAT repeatedly until “RPT ALL” appears. Press
ENTER.
To repeat desired tracks:
“USB/IPOD” is shown on the main display.
2
Repeat play can play one track, all tracks or a programmed
sequence continuously.
Connect the USB storage device.
The number of folders or files stored on the connected USB
storage device appear on the main display automatically.
• This receiver does not support a USB hub.
• If iPod/iPhone/iPad is connected, the unit will begin
charging.
Perform steps 1 - 5 in “Programmed play” section on page 21
and then press REPEAT repeatedly until “RPT ALL” appears.
Press ENTER.
Español
It is possible to listen to two-channel audio using the USB
interface on the front of this receiver.
• Pioneer does not guarantee that any file recorded on a
USB storage device will play or that power will be
supplied to a USB storage device. Also note that Pioneer
will accept no responsibility whatsoever for loss of files
on USB storage devices caused by connection to this
unit.
Français
Playing USB storage devices
To cancel repeat play:
Press REPEAT repeatedly until “RPT OFF” appears. Press
ENTER.
Note
TIMER
VOLUME
• After performing repeat play, be sure to press .
Otherwise, the file of USB storage device will play
continuously.
• During repeat play, random play is not possible.
Random play
The file of USB storage device can be played in random order
automatically.
USB storage device
(commercially available)
3 When the recognition is completed, press
 to start playback.
When changing to a different input source, stop the USB
memory playback first, before changing.
4 Disconnect USB storage device from the USB
terminal.
Turn the power off before removing the USB storage device.
Note
• This unit may not recognize a USB storage device, play
files or supply power to a USB storage device. For
details, see When a USB storage device is connected on
page 35.
• When a USB storage device is not playing and the unit
has not been operated for 20 minutes or more, the power
will automatically turn off. In this case it is required that
the Auto power off is switched to ON (page 38).
To random play all tracks:
Press RANDOM repeatedly until “RDM ON” appears. Press
ENTER.
To cancel random play:
Press RANDOM repeatedly until “RDM OFF” appears. Press
ENTER.
Note
• If you press the  during random play, you can move
to the track selected next by the random operation.
• In random play, the unit will select and play tracks
automatically. (You cannot select the order of the
tracks.)
• During random play, repeat play is not possible.
23
En
X-CM32_VXE8_En.book
07
24 ページ
年
月
日 水曜日 午後
時
分
USB playback
Specify the folder to play
Specify the folder to play, do the follwing steps.
1 Press USB, and connect the USB storage
device.
2 Press FOLDER, and press / to select
desired playback folder.
3
Press ENTER.
Playback will start from the first song of the selected folder.
• In case of stop, press /, and the folder can be
selected.
Switch the display contents
This unit can switch the information recorded in the USB
storage device. For details, see Switch the display contents on
page 22.
24
En
Playing in the desired order
(Programmed Play)
• This unit can play repeatedly folders stored in the USB
storage device.
• From a USB storage device with MP3/WMA files up to
255 folders and 999 files (including non playable files)
can be read.
X-CM32_VXE8_En.book
25 ページ
年
月
日 水曜日 午後
時
分
Using the tuner
08
English
Chapter 8:
Using the tuner
To receive an FM stereo transmission:
Listening to the radio broadcasts
OPEN/CLOSE


CD
USB
TUNER
AUDIO IN
iPod
BT AUDIO
CLOCK/TIMER
SLEEP
DISPLAY
FOLDER
TUNE+
ENTER
MEMORY
/PROGRAM
MENU
EQUALIZER
1
2
3
4
5
6
P.BASS
PRESET
8
+
CLEAR
–
9
REPEAT
RANDOM
0
DISPLAY
FOLDER
Saving station presets
If you often listen to a particular radio station, it’s convenient
to have the receiver store the frequency for easy recall
whenever you want to listen to that station (Preset tuning).
This saves the effort of manually tuning in each time. This unit
can memorize up to 40 stations.
(FM 30 stations/DAB 10 stations)
–
DIMMER


TUNE+
This will change the tuner from stereo to mono and usually
improve the reception.
MUTE
BASS/TREBLE
7
VOLUME
TUNE–
+
Improving poor FM reception:
1 Press ST/MONO repeatedly to select MONO.
Español
STANDBY/ON
Press ST/MONO to select stereo mode and “AUTO” will be
displayed.
Français
The following steps show you how to tune in to FM and DAB+
radio broadcasts using the automatic (search) and manual
(step) tuning functions. Once you are tuned to a station you
can memorize the frequency for recall later. See Saving
station presets below for more on how to do this.

ST/MONO RDS ASPM
0



PTY
DISPLAY
DISPLAY
CLEAR
TUNE+
REPEAT
RANDOM
0
FOLDER
DISPLAY
TUNE+
FOLDER
ENTER
Tuning
3 Press TUNE +/– on the remote control to
tune in to the desired station.
Automatic tuning:
MEMORY
/PROGRAM
MENU
PRESET
1 Press the  STANDBY/ON to turn the power
on.
2 Press TUNER repeatedly to select desired
frequency band (FM or DAB+).
ENTER
MEMORY
/PROGRAM
MENU
TUNE–
+
VOLUME
+
PRESET

1
–
DIMMER
TUNE–
+
MUTE
–
VOLUME
+
MUTE

–
–
Tune to a station you want to memorize.
See Tuning above for more on this.
2
Press MEMORY/PROGRAM.
The preset number will flash.
Press and hold TUNE +/–, scanning will start automatically
and the tuner will stop at the first receivable broadcast
station.
3 Press PRESET +/– to select the preset
channel number.
Manual tuning:
4 Press MEMORY/PROGRAM to store that
station in memory.
Press the TUNE +/– repeatedly to tune in to the desired
station.
Note
• When radio interference occurs, automatic tuning may
stop automatically at that point.
• Automatic tuning will skip weak signal stations.
• To stop the automatic tuning, press .
• When an RDS (Radio Data System) station is tuned in,
the frequency will be displayed first. Finally, the station
name will appear.
• Full auto tuning can be achieved for RDS stations using
Auto Station Program Memory (ASPM) mode, see
page 27.
If the preset number has changed from flashing to lighting,
before the station is memorised, repeat the operation from
step 2.
• Repeat steps 1 - 4 to set other stations, or to change a
preset station. When a new station is stored in the
memory, the station previously memorised for that
preset channel number will be erased.
Note
• The backup function protects the memorised stations for
a few hours should there be a power failure or the AC
power cord become disconnected.
25
En
X-CM32_VXE8_En.book
08
26 ページ
年
月
日 水曜日 午後
時
分
Using the tuner
To recall a memorised station
1 Press PRESET +/– to select the desired
station.
To scan the preset stations
The stations saved in the memory can be scanned
automatically. (Preset memory scan)
1
Press and hold PRESET +/–.
The preset number will appear and the programmed stations
will be tuned in sequentially, for 5 seconds each.
2 Press PRESET +/– again when the desired
station is located.
To erase entire preset memory
1
Press TUNER on the remote control.
2
Press CLEAR until “MEM CLR” appears.
Note
• All stations will be erased.
Using the Radio Data System (RDS)
An introduction to RDS
Radio Data System (RDS) is a system used by most FM radio
stations to provide listeners with various kinds of
information—the name of the station and the kind of show
they’re broadcasting, for example.
One feature of RDS is that you can search by type of program.
For example, you can search for a station that’s broadcasting
a show with the program type, JAZZ.
You can search the following program types:
NEWS – News
AFFAIRS – Current Affairs
INFO – General Information
SPORT – Sport
EDUCATE – Educational
DRAMA – Radio plays, etc.
CULTURE – National or
regional culture, theater, etc.
SCIENCE – Science and
technology
VARIED – Usually talk-based
material, such as quiz shows
or interviews.
POP M – Pop music
ROCK M – Rock music
EASY M – Easy listening
LIGHT M – ‘Light’ classical
music
CLASSICS – ‘Serious’ classical
music
OTHER M – Music not fitting
above categories
WEATHER – Weather reports
FINANCE – Stock market
reports, commerce, trading,
etc.
CHILDREN – Programs for
children
SOCIAL – Social affairs
RELIGION – Programs
concerning religion
PHONE IN – Public expressing
their views by Phone
TRAVEL – Holiday-type travel
rather than traffic
announcements
LEISURE – Leisure interests
and hobbies
JAZZ – Jazz
COUNTRY – Country music
NATION M – Popular music in
a language other than English
OLDIES – Popular music from
the ‘50s and’ 60s
FOLK M – Folk music
DOCUMENT – Documentary
TEST – Broadcasting when
testing emergency broadcast
equipment or receivers.
ALARM – Emergency
announcement made under
exceptional circumstances to
give warning of events causing
danger of a general nature.
Searching for RDS programs
You can search a program type listed above.
1
Press TUNER on the remote control.
RDS is only possible in the FM.
2
Press RDS PTY on the remote control.
“SELECT” will appear for about 6 seconds.
3 Press / to select the program type you
want to hear.
Each time the button is pressed, the program type will appear.
If the button is held down, the program type will appear
continuously.
4 Whilst the selected program type is
displayed (within 6 seconds), Press RDS PTY
again.
After the selected program type has been lit for 2 seconds,
“SEARCH” will appear, and the search operation will start.
Note
• If the display has stopped flashing, start again from step
2. If the unit finds a desired program type, the
corresponding channel number will lit for about 8
seconds, and then the station name will remain it.
• If you want to listen to the same program type of another
station, press the RDS PTY whilst the channel number or
station name is flashing. The unit will look for the next
station.
26
En
X-CM32_VXE8_En.book
27 ページ
年
月
日 水曜日 午後
時
分
Using the tuner
08
Information provided by RDS
Each time the RDS DISPLAY is pressed, the display will switch
as follows:
OPEN/CLOSE


DVD/CD
USB
iPod
BT AUDIO
SUBTITLE
ANGLE
1
2
3
ZOOM
MEMORY
PROGRAM
4
5
ENTER
SLEEP
EQUALIZER
PRESET
P.BASS
8
9
–
RPT/RDM DISPLAY
MENU/PBC
–
DIMMER


TUNE+
+
MUTE
0
TOP MENU
VOLUME
TUNE–
+
BASS/TREBLE

ST/MONO RDS ASPM

PTY
DISPLAY
DAB SCAN ENTER
Station name (PS)
Frequency


DISPLAY
Programme type (PTY)
Radio text (RT)
When tuning in to a station other than an RDS station or to an
RDS station which sends weak signal, the display will change
in the following order:
No RDS
FM 98.80 MHz
Using the Auto Station program
Memory (ASPM)
Whilst in the ASPM operation mode, the tuner will
automatically search for new RDS stations. Up to 30 stations
can be stored.
If you have already stored some stations in memory, the
number of new stations you can store will be less.
1
Notes for RDS operation
Español
A-B
MEMORY
/PROGRAM
MENU
6
ST/MONO VIDEO MODE
7
FOLDER
TUNE+
TUNER AUDIO IN/LINE
CLOCK/TIMER
AUDIO
CLEAR
DISPLAY
Français
STANDBY/ON
Note
• If the same station is broadcasting on different
frequencies, the strongest frequency will be stored in
memory.
• Any station which has the same frequency as the one
stored in memory will not be stored.
• If 30 stations have already been stored in memory, the
scan will be aborted. If you want to redo the ASPM
operation, erase the preset memory.
• If no station have been stored in memory, “END” will
appear for about 4 seconds.
• If the RDS signals are very weak, station names may not
be stored in memory.
• The same station name can be stored in different
channels.
• In a certain area or during certain time periods, the
station names may temporarily be different.
English
• If no station can be found, “NO FOUND” will appear for
4 seconds.
If any of the following events occur, it does
not mean that the unit is faulty:
• “PS”, “No PS” and a station name appear alternately,
and properly.
• If a particular station is not broadcasting properly or a
station is conducting tests, the RDS reception function
may not work properly.
• When you receive an RDS station whose signal is too
weak, information like the station name may not be
displayed.
• “No PS”, “No PYT” or “No RT” will flash for about 5
seconds, and then the frequency will be displayed.
Notes for radio text:
• The first 8 characters of the radio text will appear and
then they will scroll across the display.
• If you tune in to an RDS station which is not
broadcasting any radio text, “No RT” will be displayed
when you switch to the radio text position.
• Whilst radio text data is received or when the text
contents change, “RT” will be displayed.
Press TUNER on the remote control.
2 Press and hold down RDS ASPM on the
remote control.
After “ASPM” has flashed for about 4 seconds, scanning will
start (87.5 - 108 MHz).
After scanning, the number of stations stored in memory will
be displayed for 4 seconds, and then “END” will appear for 4
seconds.
To stop the ASPM operation before it is
complete:
Press  whilst it is scanning for stations. The stations which
are already stored in memory will be kept there.
27
En
X-CM32_VXE8_En.book
08
28 ページ
年
月
日 水曜日 午後
時
分
Using the tuner
After the scan:
Listening to the DAB+
About DAB+ (Digital Audio
Broadcasting)
Digital Audio Broadcasting is a digital transmission system
where audio signals are converted to digital signals for
broadcasting. DAB+ is broadcast as a group of data called
multiplex (ensemble) which may contain one or more stations
(services). Each station contains a primary service and there
may be one or more secondary services. This allows several
programmes or services to be transmitted on a single
frequency.
DAB + SIGNAL
The stations will be stored in alphanumeric order and the first
station on the list will be selected and you will hear it through
the speakers.
• To listen to other stations, see Selecting a station in the
station list below.
Note
• If no station is found, "NO SIG" appears.
• Up to 100 appears for total received stations.
Selecting a station in the station list
Once a DAB+ station is received, you can select stations in
the station list.
1 Press the TUNER until "DAB" appears on the
display.
MULTIPLEX
(ENSEMBLE)
2 Whilst receiving a DAB+ station, press the
TUNE +/– to select the desired station.
SERVICES
SERVICES
COMPONENTS
(STATIONS)
DISPLAY
FOLDER
TUNE+
MEMORY
/PROGRAM
PRESET
VOLUME
TUNE–
+
+
–
DIMMER



ST/MONO RDS ASPM



PTY
DISPLAY
DAB SCAN ENTER
DISPLAY
When turned on for the first time, the unit scans radio
stations automatically to create a station list. You can make
the auto scan again when you move the unit to other areas or
add multiplex channels to the station list.
1 Press the TUNER until "DAB" appears on the
display.
2 Press DAB SCAN on the remote control for
more than 3 seconds.
Auto Scan scanning begins.
Press the DAB SCAN once.
3 Within 10 seconds, press the TUNE +/– to
select the DAB+ frequency.
4
MUTE
–
1 Press the TUNER until "DAB" appears on the
display.
2
ENTER
MENU
En
Manual tune
You can manually store stations which Auto Scan cannot
find. If reception is poor, you can adjust the sensitivity.
Manual tune is only available after Auto tune. Perform Auto
Scan first.
Auto Scan
28
3 Within 10 seconds, press the DAB ENTER on
the remote control to tune into the desired
station.
Within 10 seconds, press the DAB ENTER.
• If the level is too low, move the aerial or unit to improve
reception.
X-CM32_VXE8_En.book
29 ページ
年
月
日 水曜日 午後
時
分
Using the tuner
You can switch DAB+ display information.
Press the DAB DISPLAY button.
Each time the button is pressed, the information display
changes in the following order.
When "NO SIG" appears, the DAB DISPLAY button does not
allow you to change the display.
DAB Frequency table (BAND III)
Frequency
Label
Frequency
Label
208.064 MHz
9D
176.640 MHz
5B
209.936 MHz
10A
178.352 MHz
5C
211.648 MHz
10B
Station name is displayed. (set by default)
180.064 MHz
5D
213.360 MHz
10C
[Scrolling text]
181.936 MHz
6A
215.072 MHz
10D
Information scrolls across the display when sent from the
station.
183.648 MHz
6B
216.928 MHz
11A
[Programme type]
185.360 MHz
6C
218.640 MHz
11B
A description of the type of content being broadcast by the
station.
187.072 MHz
6D
220.352 MHz
11C
[Multiplex name]
188.928 MHz
7A
222.064 MHz
11D
The name of the multiplex (ensemble) which provides the
current service.
190.640 MHz
7B
223.936 MHz
12A
[Frequency]
192.352 MHz
7C
225.648 MHz
12B
[Station Name]
The DAB+ frequency for the station.
194.064 MHz
7D
227.360 MHz
12C
Display stereo mode.
195.936 MHz
8A
229.072 MHz
12D
[Transfer speed]
197.648 MHz
8B
230.784 MHz
13A
[Signal quality]
199.360 MHz
8C
232.496 MHz
13B
The signal quality is displayed as a number (0 - 100).
[85-100: Good, 70-84: Fair, 0-69: Poor]
201.072 MHz
8D
234.208 MHz
13C
202.928 MHz
9A
235.776 MHz
13D
204.640 MHz
9B
237.488 MHz
13E
206.352 MHz
9C
239.200 MHz
13F
[Stereo mode]
Español
5A
Français
174.928 MHz
English
Changing the information display
08
The data transfer speed.
Memorising a station
You can store 10 DAB stations in memory and recall them at
the push of a button. (Preset tuning)
1
Tune to the desired DAB station.
2
Press the MEMORY/PROGRAM.
The preset number will flash.
Note
• Label is not displayed on the main display. Will displayed
only frequency.
3 Within 10 seconds, press the PRESET +/– to
select the preset channel number.
Store the stations in memory, in order, starting with preset
channel 1.
4 Within 10 seconds, press the MEMORY/
PROGRAM to store that station in memory.
If the preset number indicators disappear before the station is
memorised, repeat the operation from step 2.
5 Repeat steps 1 - 4 to set other stations, or to
change a preset station.
When a new station is stored in the memory, the station
previously memorised for that preset channel number will be
erased.
29
En
X-CM32_VXE8_En.book
09
30 ページ
年
月
日 水曜日 午後
時
分
Other connections
Chapter 9:
Other connections
CAUTION
• Before making or changing the connections, switch off
the power and disconnect the power cord from the AC
outlet.
Connect the rear panel LINE IN audio jacks to your auxiliary
playback component.
This unit’s rear panel
Connecting auxiliary components
Connect the front panel AUDIO IN mini-plug jack to your
auxiliary playback component.
• This method can be used to play music on this unit from
iPods/iPhones/iPads that do not support use of the iPod/
iPhone connector and USB terminal.
SPEAKER
TV
M
OOP
LINE
IN
M
NBAL 75 Ω
R
R
TIMER
PHONES
L
VOLUME
AUDIO IN
Audio cable
(commercially available)
PHONES
AUDIO IN
1
Portable audio player, etc.
Stereo mini-plug
cable (commercially
available)
1
Press AUDIO IN as the input source.
When AUDIO IN is selected, “AUDIO IN” is displayed on the
main display.
Note
• If the AUDIO IN mini-plug jack is connected to
auxiliary phones jack, the volume of the unit will be
adjusted by the volume on the playback component. If
the sound is distorted after you lower the volume of the
unit, try lowering the volume on the auxiliary playback
component.
30
En
Press AUDIO IN twice as the input source.
When LINE is selected, “LINE” is displayed on the main
display.
X-CM32_VXE8_En.book
31 ページ
年
月
日 水曜日 午後
時
分
Bluetooth® Audio playback
10
Bluetooth® Audio playback
Remote control operation
The remote control supplied with this unit allows you to play
and stop media, and perform other operations.
Note
Bluetooth wireless technology
enabled device:
Cell phone
Bluetooth wireless technology
enabled device:
Digital music player
Device not equipped with Bluetooth
wireless technology:
Digital music player
+
Bluetooth® audio transmitter
(commercially available)
Music data
TIMER
PHONES
VOLUME
AUDIO IN
STANDBY/ON
OPEN/CLOSE


CD
USB
iPod
BT AUDIO
TUNER
AUDIO IN
CLOCK/TIMER
SLEEP
EQUALIZER
1
2
3
P.BASS
4
5
6
BASS/TREBLE
7
8
CLEAR
9
REPEAT
RANDOM
0
DISPLAY
TUNE+
FOLDER
ENTER
MENU
MEMORY
/PROGRAM
The unit is capable of playing back music stored on Bluetooth
capable devices (cell phones, digital music players etc.)
wirelessly. You can also use a Bluetooth audio transmitter
(sold separately) to enjoy music from devices that do not have
Bluetooth functionality. Please refer to the user’s manual for
your Bluetooth capable device for more details.
Note
• The Bluetooth® word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any use of
such marks by PIONEER CORPORATION is under
license. Other trademarks and trade names are those of
their respective owners.
• The Bluetooth wireless technology enabled device must
support A2DP profiles.
• Pioneer does not guarantee proper connection and
operation of this unit with all Bluetooth wireless
technology enabled devices.
Pairing with the unit (Initial registration)
Español
• The Bluetooth wireless technology enabled device must
support AVRCP profiles.
• Remote control operations cannot be guaranteed for all
Bluetooth wireless technology enabled devices.
Français
Music playback using Bluetooth wireless
technology
English
Chapter 10:
In order for the unit to playback music stored on a Bluetooth
capable device, pairing must first be performed. Pairing
should be performed when first using the unit with the
Bluetooth capable device, or when the pairing data on the
device has been erased for any reason.
Pairing is a step required to allow communication using
Bluetooth wireless technology to be carried out.
• Pairing is only performed the first time that you use the
unit and the Bluetooth capable device together.
• In order to allow communication using Bluetooth
wireless technology to take place, pairing must be
performed on both the unit and the Bluetooth capable
device.
• After pressing the BT AUDIO and switching to BT
AUDIO input, perform the pairing procedure on the
Bluetooth capable device. If pairing has been performed
correctly, you will not need to perform the pairing
procedures for the unit as shown below.
Please refer to the user’s manual for your Bluetooth capable
device for more details.
1 Press the  STANDBY/ON and turn the
power to the unit on.
2
Press the BT AUDIO.
The unit switches to BT AUDIO and “PAIRING” will be
displayed.
3 Turn on the power to the Bluetooth capable
device that you wish to pair with, and perform
pairing procedure on it.
31
En
X-CM32_VXE8_En.book
10
32 ページ
年
月
日 水曜日 午後
Note
4 Confirm on the Bluetooth capable device
that pairing has been completed.
If pairing with the Bluetooth capable device has been
completed correctly, the name of the Bluetooth capable
device will be displayed on the front panel of the unit. (Only
single-byte alphanumeric characters can be displayed. Any
character that cannot be displayed will be indicated by a “*”.)
Listen to music on the unit from a
Bluetooth capable device
1
Press the BT AUDIO.
The unit will switch to BT AUDIO input.
2 A Bluetooth connection will be created
between the Bluetooth capable device and the
unit.
Procedures for connecting to the unit should be performed
from the Bluetooth capable device.
• Please refer to the user’s manual for your Bluetooth
capable device for details of the connection procedures.
3 Playback music from the Bluetooth capable
device.
Note
• When Bluetooth capable devise is not connected and no
operations have been performed for more than 20
minutes, the unit will automatically power off. In this
case it is required that the Auto power off is switched to
ON.
• Auto power off can be switched to ON/OFF (page 38).
En
分
Bluetooth® Audio playback
• This unit will be displayed as “X-CM32”, “X-CM325” or “XCM42” on all Bluetooth capable devices that you have.
Pairing will start.
• Place the Bluetooth capable device close to the unit.
• Please refer to the user’s manual for your Bluetooth
capable device for details on when pairing can be
performed and the procedures required for pairing.
• When PIN code entry is requested, enter “0000.” (This
unit does not accept any PIN code setting other than
“0000.”)
32
時
BT STANDBY
• The following can be done when the unit is on standby
with the BT STANDBY switched ON.
• By selecting a Bluetooth capable device that already has
a connection history (pairing has already been
conducted) with this unit, this unit will automatically
turn on with the BT AUDIO function.
BT STANDBY settings
• Switch ON/OFF by long pressing the INPUT button
located on the top of the unit for 3 seconds.
• When the power is ON, long press the INPUT button.
This cannot be operated if the power is not on.
• The setting operation can only be performed by using the
INPUT button on the unit. The setting cannot be
performed using the remote control.
Note
• When the BT STANDBY is ON, “BT STANDBY ON” is
displayed on the main display.
• When the BT STANDBY is OFF, “BT STANDBY OFF” is
displayed on the main display.
Connection while in BT STANDBY mode with
Bluetooth capable device
When connection history (pairing has already been
conducted) with a Bluetooth capable device exists for the unit
during BT STANDBY, the unit can receive a connection
request directly from the connection history.
The unit will start using the BT AUDIO function, and connect
with a Bluetooth capable device.
Even devices that have already been paired with this unit will
not connect during BT STANDBY in the following cases.
In such cases, delete pairing history from the Bluetooth
wireless technology device and perform pairing again.
• Up to 8 pairing history can be recorded with this unit. If
connecting to a Bluetooth wireless technology device
over 8 units, the oldest pairing history will be deleted.
• If the settings are reset to the factory setting, all pairing
history will be deleted.
X-CM32_VXE8_En.book
33 ページ
年
月
日 水曜日 午後
時
分
Bluetooth® Audio playback
The radio waves received by this unit include the radio wave
coming directly from the device equipped with Bluetooth
wireless technology (direct wave) and waves coming from
various directions due to reflections by walls, furniture and
building (reflected waves). The reflected waves (due to
obstacles and reflecting objects) further produce a variety of
reflected waves as well as variation in reception condition
depending on locations. If the audio cannot be received
properly due to this phenomenon, try moving the location of
the device equipped with Bluetooth wireless technology a
little. Also note that audio may be interrupted due to the
reflected waves when a person crosses or approaches the
space between this unit and the device equipped with
Bluetooth wireless technology.
Español
Note
• In the event noise appears in your television image, there
is the possibility that a Bluetooth wireless technology
enabled device or this unit (including products
supported by this unit) are causing signal interference
with the antenna input connector of your television,
video, satellite tuner, etc. In this event, increase the
distance between the antenna input connector and the
Bluetooth wireless technology enabled device or this
unit (including products supported by this unit).
• If there is something obstructing the path between this
unit (including devices supported by this unit) and the
device equipped with Bluetooth wireless technology
(such as a metal door, concrete wall, or insulation
containing tinfoil), you may need to change the location
of your system to prevent signal noise and interruptions.
Radio wave reflections
Français
This unit uses a 2.4 GHz radio wave frequency, which is a
band used by other wireless systems (see list below). To
prevent noise or interrupted communication, do not use this
unit nearby such devices, or make sure these devices are
switched off during use.
• Cordless phones
• Cordless facsimiles
• Microwave ovens
• Wireless LAN devices (IEEE802.11b/g)
• Wireless AV equipment
• Wireless controllers for game systems
• Microwave-based health aids
• Some baby monitors
Other, less common, equipment that may operate on the
same frequency:
• Anti-theft systems
• Amateur radio stations (HAM)
• Warehouse logistic management systems
• Discrimination systems for train or emergency vehicles
• If you live in a heavily populated residential area
(apartment, townhouse, etc.) and if your neighbor’s
microwave is placed near your system, you may
experience radio wave interference. If this occurs, move
your unit to a different place. When the microwave is not
in use, there will be no radio wave interference.
English
Radio wave caution
10
Precautions regarding connections to
products supported by this unit
• Complete connections for all devices supported by this
unit, including all audio cords and power cables before
connecting them to this unit.
• After completing connections to this unit, check the
audio and power cables to confirm that they not twisted
together.
• When disconnecting this unit, confirm that you have
sufficient working space in the surrounding area.
• When changing connections of audio or other cables for
products supported by this unit, confirm that you have
sufficient working space in the surrounding area.
Scope of operation
Use of this unit is limited to home use. (Transmission
distances may be reduced depending on communication
environment).
In the following locations, poor condition or inability to receive
radio waves may cause the audio to be interrupted or stopped:
• In reinforced concrete buildings or steel framed or ironframed buildings.
• Near large metallic furniture.
• In a crowd of people or near a building or obstacle.
• In a location exposed to the magnetic field, static
electricity or radio wave interference from radio
communication equipment using the same frequency
band (2.4 GHz) as this unit, such as a 2.4 GHz wireless
LAN device (IEEE802.11b/g) or microwave oven.
33
En
X-CM32_VXE8_En.book
11
34 ページ
年
月
日 水曜日 午後
時
分
Additional information
Chapter 11:
Additional information
Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this
component, check the points below. Sometimes the trouble may lie in another component. Investigate the other components
and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks listed below, ask your
nearest Pioneer authorized service center or your dealer to carry out repair work.
• If the unit does not operate normally due to external effects such as static electricity disconnect the power plug from the
outlet and insert again to return to normal operating conditions.
General problem
Problem
Check
Settings you have made have Was the power cord unplugged?
been cleared.
Remedy
When power cord is unplugged, the settings you have made is
cleared. Please set the clock again. If you do not want to clear the
settings, do not unplug the power cord.
Difference in volume
between CDs, MP3, WMA,
iPod/iPhone/iPad, Tuner,
AUDIO IN and LINE.
This is not a problem with this unit.
The volume may sound differently depending on the input source
and recording format.
This unit cannot be operated
with the remote control.
Are you operating from far away?
Operate within 7 m, 30º of the remote sensor on the front panel
(page 5).
Is the remote control sensor exposed The remote control signals may not be received properly if the
to direct sunlight or strong artificial remote control sensor is exposed to direct sunlight or strong
artificial light from a fluorescent bulb, etc.
light from a fluorescent bulb, etc.?
Are the batteries dead?
Disc cannot be played or disc Is the disc scratched?
is ejected automatically.
Is the disc dirty?
Folder or file names are not
recognized.
The unit turns off
automatically.
34
En
Replace the batteries (page 5).
Scratched discs may not play.
Wipe the dirt off the disc (page 38).
Is this unit placed in a humid
location?
There could be condensation inside. Wait a while for the
condensation to evaporate. Do not place this unit near an airconditioner, etc. (page 37).
Have you exceeded the maximum
number of folder or file names this
unit can recognize?
Up to 255 folders can be recognized on one disc. Up to 999 files can
be recognized within one folder. Depending on the folder structure,
however, this unit may not be able to recognize certain folders or
files.
If no play back and no operation has done for 20 minutes or more,
the unit turns off automatically.
In this case it is required that the Auto power off is switched to ON
(page 38).
X-CM32_VXE8_En.book
35 ページ
年
月
日 水曜日 午後
時
分
Additional information
11
When a USB storage device is connected
Check
Remedy
USB storage device is not
recognized.
Is the USB storage device properly
connected?
Connect the device securely (all the way in).
English
Problem
Is the USB storage device connected This unit does not support USB hubs. Connect the USB storage
via a USB hub?
device directly.
This unit supports portable flash memory and digital audio
playback devices.
Only the FAT16 and FAT32 file systems are supported. Other file
systems (exFAT, NTFS, HFS etc.) are not supported.
Turn the power off then back on.
Some USB storage devices may not be recognized properly.
File cannot be played.
Is the file copyright-protected (by
DRM)?
Copyright-protected files cannot be played.
This is not a problem with this unit.
Files stored on a computer cannot be played.
Folder or file names are not
displayed or are not properly
displayed.
Do the folder of file names contain
more than 30 characters?
The maximum number of characters displayable for the folder and
file names is 30.
Folder or file names are not
displayed in alphabetical
order.
This is not a problem with this unit.
The order of the folder and file names displayed depends on the
order in which the folders or files were recorded on the USB
storage device.
Much time is required to
recognize the USB storage
device.
What is the USB storage devices
capacity?
Some time may be required to load the data when large capacity
USB storage devices are connected (this could take several
minutes).
Power is not supplied to the
USB storage device.
Is “AUTH ERR” displayed on the front Turn the power off then back on.
panel display? No power is supplied if
the power consumption is too high. Turn the power off, then disconnect and reconnect the USB storage
device.
Español
This device does not support the use of external hard disc drives.
This is not a problem with this unit.
Français
This unit only supports USB mass storage class devices.
It may not be possible to play some files.
Press INPUT to switch to the other mode, then switch again to the
USB mode.
When an iPod/iPhone/iPad is connected
Problem
Remedy
Can’t operate the iPod/iPhone/iPad by the remote control.
Make sure the iPod/iPhone/iPad is connected correctly (page 17).
Can’t operate the iPod/iPhone/iPad.
Make sure the iPod/iPhone/iPad is connected correctly (page 17).
If the iPod/iPhone/iPad is experiencing a hangup, try resetting the
iPod/iPhone/iPad, and reconnect it to the unit.
35
En
X-CM32_VXE8_En.book
11
36 ページ
年
月
日 水曜日 午後
時
分
Additional information
When the Bluetooth wireless technology device is connected or operated
Problem
Remedy
The Bluetooth wireless technology device cannot be connected or
operated.
Sound from the Bluetooth wireless technology device is not emitted
or the sound is interrupted.
Check that no object that emits electromagnetic waves in the 2.4
GHz band (microwave oven, wireless LAN device or Bluetooth
wireless technology apparatus) is near the unit. If such an object is
near the unit, set the unit far from it. Or, stop using the object
emitting the electromagnetic waves.
Check that the Bluetooth wireless technology device is not too far
from the unit and that obstructions are not set between the
Bluetoothwireless technology device and the unit. Set the Bluetooth
wireless technology device and the unit so that the distance
between them is less than about 10 m* and no obstructions exist
between them.
* The distance given is to be used as a rough guide. The actual allowable
distance between devices may vary depending on conditions in the
surrounding environment.
The Bluetooth wireless technology device may not be set to the
communication mode supporting the Bluetooth wireless
technology. Check the setting of the Bluetooth wireless technology
device.
Playable discs and formats
Audio CD
• Commercially available audio CDs
• CD-R/ -RW/ -ROM discs containing music recorded in the CD-DA format
WMA
WMA files recorded on CD-R/ -RW/ -ROM discs or USB storage devices
MP3
MP3 files recorded on CD-R/ -RW/ -ROM discs or USB storage devices
• Only the discs that have been finalized can be
played.
• Discs recorded in packet write mode (UDF format) are
not compatible with this unit.
• Corporation and product names mentioned herein are
trademarks or registered trademarks of the respective
corporations.
• Only discs recorded in ISO9660 Level 1, Level 2 and Joliet
can be played.
• Files protected by DRM (Digital Rights Management)
cannot be played.
Note
• This unit does not support multisession discs or
multiborder recording.
• Multisession/multiborder recording is a method in
which data is recorded on a single disc in two or more
sessions/borders. A “session” or “border” is one
recording unit, consisting of a complete set of data from
lead-in to lead-out.
36
En
Regarding copy protected CDs
This unit is designed to conform to the specifications of the
audio CD format. This unit does not support the playback or
function of discs that do not conform to these specifications.
Supported audio file formats
This unit does not support lossless encoding.
X-CM32_VXE8_En.book
37 ページ
年
月
日 水曜日 午後
時
分
Additional information
When moving this unit
Place of installation
Avoid the following locations:
•
•
•
•
•
•
Places exposed to direct sunlight
Humid or poorly ventilated places
Extremely hot places
Places exposed to vibrations
Places in which there is much dust or cigarette smoke
Places exposed to soot, steam or heat (kitchens, etc.)
Do not place objects on this unit
Do not place any objects on top of this unit.
Do not obstruct the ventilation holes.
Do not use this unit on shaggy rugs, beds, sofas, etc., or
wrapped in cloth, etc. Doing so will prevent the heat from
dispersing, leading to damage.
Do not expose to heat.
Cleaning the product
• Unplug the power cord from the power outlet when
cleaning this unit.
• Clean this unit using a soft cloth. For tough dirt, apply
some neutral detergent diluted in 5 to 6 parts water to a
soft cloth, wring out thoroughly, wipe off the dirt, then
wipe again with a soft, dry cloth.
• Alcohol, thinner, benzene, insecticides, etc., could cause
the print or paint to peel off. Also, leaving rubber or vinyl
products in contact with this unit for long periods of time
could mar the cabinet.
• When using chemical-impregnated wipes, etc., read the
cautions included with the wipes carefully.
Español
• Choose a stable place near the TV or stereo system being
used with this unit.
• Do not place this unit on top of a TV or color monitor. Also
install it away from cassette decks and other devices
easily affected by magnetic forces.
If this unit is moved suddenly from a cold place into a warm
room (in winter, for example) or if the temperature in the room
in which this unit is installed rises suddenly due to heater
operation, etc., water droplets (condensation) may form
inside (on operating parts and the lens). When condensation
is present, this unit will not operate properly and playback is
not possible. Let this unit stand at room temperature for 1 or
2 hours with the power turned on (the time depends on the
extent of condensation). The water droplets will dissipate and
playback will become possible. Condensation can also occur
in the summer if this unit is directly exposed to the air flow
from an air-conditioner. If this happens, move this unit to a
different place.
Français
When moving this unit, be sure to first check that there is no
disc loaded and disconnect the iPod/iPhone/iPad. Then press
 STANDBY/ON, wait for “STANDBY” disappears on main
display to turn off, then unplug the power cord. Damage may
occur if the unit is transported or moved with a disc inserted,
or when another device is connected to the iPod/iPhone/iPad
connector port, USB terminal, or AUDIO IN mini-plug jack.
About condensation
English
Cautions on use
11
Cleaning the lens
This unit’s lens should not become dirty in normal use, but if
for some reason it should malfunction due to dust or dirt,
consult your nearest Pioneer authorized service center.
Although lens cleaners for players are commercially
available, we advise against using them since some may
damage the lens.
Do not place this unit on top of an amplifier or other
component that generates heat. When rack mounting it, to
avoid the heat given off by the amplifier or other audio
component, place it on a shelf below the amplifier.
• Turn off the unit’s power when not using it.
• Depending on signal conditions, striped patterns may
appear on a TV screen and noise may enter the sound of
radio broadcasts when the unit’s power is on. If this
happens, turn the unit’s power off.
37
En
X-CM32_VXE8_En.book
11
38 ページ
年
月
日 水曜日 午後
時
分
Additional information
Handling discs
About iPod/iPhone/iPad
Storing
• Always place discs in their cases and store them
vertically, avoiding hot, humid places, places exposed to
direct sunlight and extremely cold places.
• Be sure to read the cautions included with the disc.
Cleaning discs
• Discs may not play if there are fingerprints or dust on
them. In this case, use a cleaning cloth, etc., to gently
wipe the disc from the inside towards the outside. Do not
use dirty cleaning cloths.
“Made for iPod” and “Made for iPhone” and “Made for iPad”
mean that an electronic accessory has been designed to
connect specifically to iPod, iPhone, or iPad, respectively, and
has been certified by the developer to meet Apple
performance standards. Apple is not responsible for the
operation of this device or its compliance with safety and
regulatory standards. Please note that the use of this
accessory with iPod, iPhone or iPad may affect wireless
performance.
iPad, iPhone, iPod, iPod nano and iPod touch are trademarks of
Apple Inc., registered in the U.S. and other countries.
Lightning is a trademark of Apple Inc.
Auto power off setting
• Do not use benzene, thinner or other volatile chemicals.
Also do not use record spray or antistatic agents.
• For tough dirt, apply some water to a soft cloth, wring out
thoroughly, wipe off the dirt, then wipe off the moisture
with a dry cloth.
• Do not use damaged (cracked or warped) discs.
• Do not let the signal surface of discs get scratched or
dirty.
• Do not attach pieces of paper or stickers to discs. Doing
so could warp discs, making it impossible to play them.
Also note that rental discs often have labels attached to
them, and the label’s glue may have oozed out. Check
that there is no glue around the edges of such labels
before using rented discs.
Long press the  on the unit for 3 seconds to switch auto
power off setting ON/OFF.
• The operation can be conducted using only the  on the
unit.
• No need to set this using the remote control.
• Initial setting is set to ON.
Note
• When the auto power off is set to ON, “APD ON” will be
displayed on the main display.
• When the auto power off is set to OFF, “APD OFF” will be
displayed on the main display.
Restoring all the settings to the
defaults
Use the steps below to restore the all settings to their defaults.
About specially shaped discs
Specially shaped discs (heart-shaped, hexagonal, etc.)
cannot be played on this unit. Do not attempt to play such
discs, as they could damage this unit.
1
Press  STANDBY/ON to turn the power on.
2 Press CD on the remote control or INPUT
repeatedly on the main unit to select CD input.
3
Press  OPEN/CLOSE to open the disc tray.
4 Press  STANDBY/ON on the unit for 3
seconds while pressing .
• “DEFAULT” is displayed while the settings are being
restored. Power is turned off.
• No need to set this using the remote control.
38
En
X-CM32_VXE8_En.book
39 ページ
年
月
日 水曜日 午後
時
分
Additional information
•
Amplifier section
RMS Power Output: . . . . . . . . . . . . . . . . . . . . . . . 15 W + 15 W
(1 kHz, 10 %, T.H.D., 8 )
•
Tuner section
•
Bluetooth
Español
Version . . . . . . . . . . . . . . . . . . Bluetooth Specification Ver. 3.0
Output . . . . . . . . . . . . . . . . . . . Bluetooth Specification Class 2
Estimated line-of-sight transmission distance*
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . About 10 m
Frequency range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4 GHz
Modulation
. . . . . . . . . . . . FH-SS (Frequency Hopping Spread Spectrum)
Supported Bluetooth profiles. . . . . . . . . . . . . . . A2DP, AVRCP
Supported Codec . . . . . . . . . . . . . . . . . SBC (Subband Codec)
Supported contents protection . . . . . . . . . . . . . . . . . . SCMS-T
• iOS is a trademark on which Cisco holds the trademark
right in the US and certain other countries.
Français
Frequency Range (FM). . . . . . . . . . . . . . 87.5 MHz to 108 MHz
Frequency Range (DAB) . . . . . . 174.928 MHz to 239.200 MHz
Antenna Input (DAB/FM). . . . . . . . . . . . . . . . 75  unbalanced
Note
• The specifications are applicable when the power supply
is 230 V.
• Specifications and the design are subject to possible
modifications without notice, due to improvements.
English
Specifications
11
* The line-of-sight transmission distance is an estimate.
Actual transmission distances supported may differ
depending on surrounding conditions.
•
Miscellaneous
iPod/iPhone connector port . . . . . . . . . . . . . . . . . . . . .5 V, 1 A
USB terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 V, 2.1 A
Power source . . . . . . . . . . . . . AC 220 V to 240 V, 50 Hz/60 Hz
Power consumption
Power on (X-CM32BTD, X-CM325BTD) . . . . . . . . . . . .30 W
Power on (X-CM42BTD) . . . . . . . . . . . . . . . . . . . . . . . .37 W
Power stand-by . . . . . . . . . . . . . . . . . . . . . . . . 0.5 W or less
Power stand-by (BT STANDBY ON) . . . . . . . . 0.5 W or less
Dimensions . . . . 200 mm (W) x 123 mm (H) x 257 mm (D)
Weight (without package) . . . . . . . . . . . . . . . . . . . . . . . . 2.0 kg
•
Speaker
Enclosure . . . . . . . . . . . . . . . . . . . Bass-reflex, book-shelf type
(Magnetically shielded)
Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-way
Tweeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 cm cone
Woofer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9.4 cm cone
Maximum input power. . . . . . . . . . . . . . . . . . . . . . . . . . . .15 W
Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 
Dimensions. . . . . . . 121 mm (W) x 201 mm (H) x 235 mm (D)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.0 kg/each
•
Accessories
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
AAA batteries (R03) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
DAB/FM wire antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Non-skid pads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Power cord
Speaker wire
iPhone/iPad stand
Warranty card
Operating instructions (This document)
39
En
X-CM32_VXE8_En.book
11
40
En
40 ページ
年
月
Additional information
日 水曜日 午後
時
分
X-CM32_VXE8_En.book
41 ページ
年
Additional information
月
日 水曜日 午後
時
分
11
English
Français
Español
41
En
X-CM32_VXE8_En.book
40 ページ
年
月
日 水曜日 午後
時
分
Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC
Manufacturer:
PIONEER HOME ELECTRONICS
CORPORATION
1-1, Shin-ogura, Saiwai-ku,
Kawasaki-shi, Kanagawa
212-0031, Japan
EU Representative’s:
Pioneer Europe NV
Haven 1087, Keetberglaan 1,
9120 Melsele, Belgium
http://www.pioneer.eu
[*] X-CM32BTD-K, X-CM32BTD-W
X-CM325BTD-W
X-CM42BTD-K, X-CM42BTD-W
English:
Hereby, Pioneer, declares that this [*] is
in compliance with the essential
requirements and other relevant
provisions of Directive 1999/5/EC.
Suomi:
Pioneer vakuuttaa täten että [*]
tyyppinen laite on direktiivin 1999/5/EY
oleellisten vaatimusten ja sitä
koskevien direktiivin muiden ehtojen
mukainen.
Nederlands:
Hierbij verklaart Pioneer dat het toestel
[*] in overeenstemming is met de
essentiële eisen en de andere
relevante bepalingen van richtlijn
1999/5/EG
Français:
Par la présente Pioneer déclare que
l’appareil [*] est conforme aux
exigences essentielles et aux autres
dispositions pertinentes de la directive
1999/5/CE
Svenska:
Härmed intygar Pioneer att denna [*]
står I överensstämmelse med de
väsentliga egenskapskrav och övriga
relevanta bestämmelser som framgår
av direktiv 1999/5/EG.
Dansk:
Undertegnede Pioneer erklærer
herved, at følgende udstyr [*]
overholder de væsentlige krav og
øvrige relevante krav i direktiv 1999/5/EF
Deutsch:
Hiermit erklärt Pioneer, dass sich
dieses [*] in Übereinstimmung mit den
grundlegenden Anforderungen und den
anderen relevanten Vorschriften der
Richtlinie 1999/5/EG befindet". (BMWi)
Ελληνικά:
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Pioneer ΔΗΛΩΝΕΙ
ΟΤΙ [*] ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ
ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ
ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ
ΟΔΗΟΙΑΣ 1999/5/ΕΚ
Italiano:
Con la presente Pioneer dichiara che
questo [*] è conforme ai requisiti
essenziali ed alle altre disposizioni
pertinenti stabilite dalla direttiva
1999/5/CE.
Español:
Por medio de la presente Pioneer
declara que el [*] cumple con los
requisitos esenciales y cualesquiera
otras disposiciones aplicables o
exigibles de la Directiva 1999/5/CE
X-CM32_VXE8_En.book
41 ページ
年
月
日 水曜日 午後
Português:
Pioneer declara que este [*] está
conforme com os requisitos essenciais
e outras disposições da Directiva
1999/5/CE.
Čeština:
Pioneer tímto prohlašuje, že tento [*] je
ve shodě se základními požadavky a
dalšími příslušnými ustanoveními
směrnice 1999/5/ES
Eesti:
Käesolevaga kinnitab Pioneer seadme
[*] vastavust direktiivi 1999/5/EÜ
põhinõuetele ja nimetatud direktiivist
tulenevatele teistele asjakohastele
sätetele.
Magyar:
Alulírott, Pioneer nyilatkozom, hogy a
[*] megfelel a vonatkozó alapvetõ
követelményeknek és az 1999/5/EC
irányelv egyéb elõírásainak.
Latviešu valoda:
Ar šo Pioneer deklarē, ka [*] atbilst
Direktīvas 1999/5/EK būtiskajām
prasībām un citiem ar to saistītajiem
noteikumiem.
Lietuvių kalba:
Šiuo Pioneer deklaruoja, kad šis [*]
atitinka esminius
reikalavimus ir kitas 1999/5/EB
Direktyvos nuostatas.
Malti:
Hawnhekk, Pioneer jiddikjara li dan [*]
jikkonforma mal-ħtiġijiet essenzjali u ma
provvedimenti oħrajn relevanti li hemm
fid-Dirrettiva 1999/5/EC
Slovenčina:
Pioneer týmto vyhlasuje, že [*] spĺňa
základné požiadavky a všetky príslušné
ustanovenia Smernice
1999/5/ES.
時
分
Slovenščina:
Pioneer izjavlja, da je ta [*] v skladu z
bistvenimi zahtevami in ostalimi
relevantnimi določili direktive
1999/5/ES.
Română:
Prin prezenta, Pioneer declara ca acest
[*] este in conformitate cu cerintele
esentiale si alte prevederi ale Directivei
1999/5/EU.
български:
С настоящето, Pioneer декларира, че
този [*] отговаря на основните
изисквания и други съответни
постановления на Директива
1999/5/EC.
Polski:
Niniejszym Pioneer oświadcza, że
[*] jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi
postanowieniami
Dyrektywy 1999/5/EC
Norsk:
Pioneer erklærer herved at utstyret [*]
er i samsvar med de grunnleggende
krav og øvrige relevante krav i direktiv
1999/5/EF.
Íslenska:
Hér með lýsir Pioneer yfir því að
[*] er í samræmi við
grunnkröfur og aðrar kröfur, sem gerðar
eru í tilskipun 1999/5/EC
Hrvatski:
Ovime tvrtka Pioneer izjavljuje da je
ovaj [*] u skladu osnovnim zahtjevima i
ostalim odredbama Direktive
1999/5/EC.
R-TTE-24L_C1_En
X-CM32_VXE8_En.book
42 ページ
年
月
日 水曜日 午後
時
分
http://www.pioneer.co.uk
http://www.pioneer.eu
© 2014 PIONEER HOME ELECTRONICS CORPORATION.
All rights reserved.
PIONEER HOME ELECTRONICS CORPORATION
1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan
PIONEER ELECTRONICS (USA) INC.
P.O. BOX 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404
PIONEER ELECTRONICS OF CANADA, INC.
340 Ferrier Street, Unit 2, Markham, Ontario L3R 2Z5, Canada TEL: 1-877-283-5901, 905-479-4411
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
5 Arco Lane, Heatherton, Victoria, 3202, Australia, TEL: (03) 9586-6300
PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.
Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico, D.F. 11000 TEL: 55-9178-4270
K002_B3_En
Printed in China
<YOM200145-0018>
Y
O
M
2
0
0
1
4
5
-
0
0
1
8
Download PDF
Similar pages