Cyrus Stereo 200
User Instructions
CONTENTS
IMPORTANT! Read before operating this equipment!....1
Power supply..............................................................................2
Servicing.....................................................................................2
Product service centres..............................................................2
FCC NOTICE.................................................................................3
Welcome to the world of Cyrus!........................................4
Preparations for Installation.......................................................4
Speaker detection......................................................................4
Installation................................................................................5
Key to the rear panel drawing....................................................5
Placement...................................................................................6
Important – read before making any audio connections...........6
Connecting a Pre-Amplifier, Streamer or DAC............................6
Connecting via phono (RCA) interconnects...........................6
Connecting using Balanced XLR cables..................................6
Connecting Loudspeakers...........................................................7
Choice of speaker cables.......................................................7
Speaker cable polarity...........................................................7
Cable termination..................................................................7
Connecting spade tags..........................................................7
Connecting bare wire terminations.......................................7
Connecting the cables to your speakers................................7
Input and speaker connections.............................................7
Chain Output..............................................................................8
Bi-Amplification.....................................................................8
Gain Matching.......................................................................8
Chain output and bi-amplified speaker connection..............8
Remote Power Control (MC-BUS or 12V Trigger).......................9
Connecting MC-BUS..............................................................9
Connecting to a 12V trigger equipped system......................9
Connecting to the AC Mains Supply.........................................10
OPERATION..................................................................................11
Power Control...........................................................................12
Power operation sequence.................................................12
Power control from the front panel....................................12
First use...............................................................................12
Music sensing automatic power control.............................12
Input Indicator..........................................................................12
Selecting an Input.....................................................................12
TROUBLESHOOTING GUIDE........................................................13
SPECIFICATIONS...........................................................................14
Power Supply.......................................................................14
Power Consumption............................................................14
Enclosure.............................................................................14
Audio Performance.............................................................14
WARRANTY...................................................................................14
WEEE.............................................................................................14
Cyrus Stereo 200
User Instructions
IMPORTANT! Read before operating this equipment!
CAUTION: The exclamation mark is to draw your
attention to important instructions and safety
procedures in this manual.
ATTENTION: The lightning flash warns you of the
risk of electrical shock presented by components
inside this product. Unauthorised personnel
must not open this unit. ATTACHMENTS: Do not use attachments not recommended
by the product manufacturer as they may cause hazards.
MOVING THE PRODUCT: A product and cart
combination should be moved with care. Sudden
stops, excessive force, and uneven surfaces may
cause the product and cart to overturn.
POWER SOURCES: This product should be operated only
from the type of power source indicated on the marking
label. If you are not sure of the type of power supply to your
home, consult your product dealer or local power company.
For products intended to operate from battery power, or
other sources, refer to the operating instructions.
OVERLOADING: Never overload wall outlets, extension
cords, or integral convenience receptacles. This can result in
an increased risk of fire or electric shock.
POWER CORD PROTECTION: Power supply cords should be
routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and
the point where they exit from the product.
NAKED FLAMES: No naked flame sources, such as candles,
must be placed on this product.
LIGHTNING: For added protection for this product during
a lightning storm, or when it is left unattended or unused
for long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line
surges.
BATTERIES: Warning : Batteries shall not be exposed to
excessive heat such as sunshine, fire or the like.
CAUTION! POLARISED CONNECTOR (CANADA and USA): To
prevent electrical shock, match wide blade of plug to wide
slot, fully insert.
Do not alter or remove this plug if it does not fit your
mains power socket. Have a suitable socket installed by a
competent electrician.
ACCESS TO THE MAINS PLUG: The means to disconnect this
product from the mains supply is the mains plug. Ensure
that the mains plug is accessible at all times.
WARNING: This appliance must be earthed.
WARNING: To reduce the risk of electrical shock do not
remove any unit covers or panels. There are no user
serviceable parts in this product.
WARNING: To reduce the risk of electric shock, do not
expose this equipment to rain or moisture.
HEED WARNINGS: All warnings on the product and in the
operating instructions should be adhered to.
READ ALL THE INSTRUCTIONS: All the safety and operating
instructions should be read before the product is operated.
RETAIN INSTRUCTIONS: The safety and operating
instructions should be retained for future reference.
FOLLOW INSTRUCTIONS: All operating and use instructions
should be followed.
CLEANING: Unplug this product from the mains before
cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth for cleaning.
WATER AND MOISTURE: Do not use this product near water
- for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub, in a wet basement; or near a swimming pool
and the like. The product must not be exposed to dripping
or splashing and no objects filled with liquids, such as vases,
shall be placed on the product.
HEAT: The product should be situated away from heat
sources such as radiators, stoves, or any other products
(including amplifiers) that produce heat.
VENTILATION: Slots and openings in the cabinet are
provided for ventilation, to ensure reliable operation of
the product and to protect it from overheating and these
openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed,
sofa, rug or similar surface. This product should not be
placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
OBJECT OR LIQUID ENTRY: Never push objects of any kind
into this product through openings as they may touch
dangerous voltage points or short-out parts that could
result in a fire or electric shock.
ACCESSORIES: Do not place this product on an unstable
cart, stand, tripod, bracket, or table. The product may fall,
causing serious injury to a child or adult, and serious damage
to the product. Use only with a cart, stand, tripod, bracket
or table recommended by the manufacturer, or sold with
the product. Any mounting of the product should follow
the manufacturer’s instructions, and should use a mounting
accessory recommended by the manufacturer.
1
Cyrus Stereo 200
User Instructions
Power supply
Servicing
The mains supply requirement for your Stereo 200 is marked
on a label on the rear panel. Before connecting power, check
that this voltage is the same as your mains supply.
230V Products: Voltage Range 220V-240V
115V Products: Voltage Range 110V-120V
If you move to an area with a different mains voltage,
contact your local Cyrus distributor to have your product
converted.
There are no user replaceable fuses in this unit.
Do not attempt to service this product yourself as opening
or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to qualified service
personnel.
CONDITIONS REQUIRING SERVICE: Unplug this product
from the wall outlet and refer servicing to qualified service
personnel when:
• When the power supply cord or plug is damaged.
• If liquid has been spilled, or objects have fallen into the
product.
• If the product has been exposed to rain or water.
• If the product has been dropped or damaged in any
way.
• If the product does not operate normally by following
the operating instructions. (Adjust only those controls
that are covered by the operating instructions. Improper
adjustment of other controls may result in damage
requiring extensive work by a qualified technician to
restore the product to its normal operation).
• When the product exhibits a distinct change in
performance.
REPLACEMENT PARTS: When replacement parts are
required, be sure the service technician has used
replacements specified by the manufacturer or have the
same characteristics as the original part. Unauthorised
substitutions may result in fire, electric shock, or other
hazards.
SAFETY CHECK: Upon completion of any service or repairs
to this product, ask the service technician to perform safety
checks to determine that the product is in proper operating
condition.
Product service centres
For product service or technical advice, contact only
authorised Cyrus service centres. Contact details for Cyrus
distributors may be found on the Cyrus website at www.
cyrusaudio.com.
2
Cyrus Stereo 200
User Instructions
FCC NOTICE*
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try and correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the manufacturer could void
the user’s authority to operate the equipment.
*115V products
3
Cyrus Stereo 200
User Instructions
Welcome to the world of Cyrus!
Preparations for Installation
Congratulations on your choice of Cyrus Hi-fi products. Our
state-of-the-art design technology and outstanding quality
of manufacture has won countless awards around the
world. We are confident that you will derive great pleasure
from owning a product from one of the most recognised and
respected manufacturers of hi-fi equipment.
Now is a good time to register your new Cyrus product.
Registration takes only a few minutes, brings the added
benefit of a full three year factory warranty and adds you to
our mailing list for future product updates and upgrades. To
register, visit www.cyrusaudio.com and click the ‘Register’
link.
Please read these instructions carefully before commencing
installation. They provide full guidance to help you install
your amplifier safely and correctly.
Before installing the Stereo 200 check that the following
items are included in the accessory box.
• Power Cable
• 2 MC-BUS cables
• Ferrite clamp
After removing these items, please retain the packaging.
Install the amplifier in a well ventilated location away from
sources of high temperature, dust or humidity. Never stand
the amplifier under another unit or on any surface likely to
hamper its cooling or ventilation.
Speaker detection
The Stereo 200 automatically measures the impedance of
your speakers and adjusts its performance accordingly. The
process takes a few seconds and only takes place on the first
occasion that the amplifier is switched on after connection
to the mains.
NOTE: A faint noise may be heard through the speakers
during optimisation. This is normal.
Once the speakers have been measured, the results are
stored until mains power is next disconnected.
To ensure that this speaker optimisation runs correctly,
follow these guidelines • Make all connections, including speakers, to the amplifier
before connecting mains power.
• Turn the system volume control to minimum when
speaker optimisation is running.
• If you change your speakers, disconnect the amplifier
from mains power and re-connect it once the new
speakers are connected.
NOTE: The amplifier will not be damaged if you switch on
before connecting the speakers, but performance may be
compromised.
4
Cyrus Stereo 200
User Instructions
Installation
a
b
c
a
d
e
f
SPEAKER
SPEAKER
RIGHT
INPUT
CHAIN
WARNING:
THIS APPLIANCE
MUST BE EARTHED
INPUT
TRIGGER
INPUT
ATTENTION:
CET APPAREIL DOIT
ÊTRE BRANCHÉ À
LA TERRE
OUT
h
i
IN
g
Key to the rear panel drawing
1.
2.
3.
4.
5.
6.
7.
8.
9.
ight speaker output
R
Right channel balanced input
Chain output
Unbalanced RCA (phono) Input
Left channel balanced input
Left speaker output
MC-BUS connections
12V trigger input
IEC Power Inlet
5
LEFT
INPUT
MC-BUS
MADE IN ENGLAND
Cyrus Stereo 200
User Instructions
Placement
Important – read before making any audio
connections
When installing a Stereo 200 amplifier, choose a position
where there is at least 3cm clearance from the sides and
top of the amplifier to allow cooling air to circulate. Never
stand the amplifier on a soft or carpeted surface or install
the amplifier in an enclosed space or cabinet where cool air
cannot enter.
To avoid possible damage to your amplifier, it is essential to
disconnect all system components from the mains supply
before connecting or disconnecting audio interconnects.
Connecting a Pre-Amplifier, Streamer or DAC
NOTE: When connecting a streamer or DAC to a Stereo
200, ensure that it includes a volume control and use the
‘variable’ or ‘preamp’ output.
Phono (RCA) d and Balanced input connectors b/e are
available to link the Stereo 200 to a pre-amplifier, streamer
or D/A converter etc.
If your amplifier is a long distance from the pre-amplifier/
DAC, or beside a loudspeaker, then balanced XLR connections
b/e may give improved performance.
Connecting via phono (RCA) interconnects
Connect a stereo phono interconnect from the output of
the preamplifier to the left and right inputs d of the Stereo
200. Be sure to observe colour coding of the plugs to keep
left and right channels correctly ordered.
Connecting using Balanced XLR cables
Connect a 3-pin XLR cable from the balanced outputs of the
preamplifier to the left e and right b balanced inputs of the
Stereo 200.
6
Cyrus Stereo 200
User Instructions
Connecting Loudspeakers
Connecting spade tags
• Unscrew the knobs on the four speaker terminals a
and f.
• Fit each spade terminal under the knob of the correct
terminal.
• Tighten the knob securely.
• Repeat these steps for the other terminals.
• Check carefully that channel and cable polarities are
correct.
Connecting bare wire terminations
• Unscrew the knobs on the four speaker terminals a
and f.
• If the cables are stranded, twist the cables before
fitting them to the terminals.
• Pass the cable ends through the cross-holes in
the terminals. Check that there are no loose wire
strands.
• Tighten the knob securely.
• Repeat these steps for the other terminals.
• Check carefully that channel and cable polarities are
correct.
Connecting the cables to your speakers.
• Refer to the speaker instructions for cable
connection.
Choice of speaker cables
When choosing speaker cables, avoid litz-wound cables with
a complex ‘plaited wire’ construction. These cables can be
highly reactive and may degrade the sound of your amplifier.
Always choose a cable of simple construction, manufactured
from high quality materials and priced sensibly within the
cabling budget of your system.
If in doubt about the correct cable to choose, any Cyrus
retailer will be able to advise.
CAUTION: The speaker outlets are only suitable for
connection directly to speakers. Never connect any switchbox or other device to the speaker outlets.
Speaker cable polarity
Speaker cables will always include polarising marks such as a
rib or stripe to indicate the ‘+’ wire and red/black identifiers
on the terminals. Ensure you connect the red terminal/
striped cable to the + terminals.
Cable termination
Speaker cables for use with the Stereo 200 may be terminated
with spade tags or bare wire ends.
Spade tags will give the best quality connection. Bare wire
ends may be used, but very thin or highly stranded cables
may be better with spade termination to protect the fragile
cable end.
Input and speaker connections
Preamplifier
OUT
L
MCBUS
Right
speaker
terminals
R
IN
PRE OUT 1 PRE OUT 2
ZONE 2
OUT
HEADPHONE
MADE IN ENGLAND
IN-6
IN-5
IN-4
IN-3
IN-2
IN-1
USE PSX-R ONLY
IN-7
IN-8
IN-9
IN-10
Left
speaker
terminals
IN-11
Stereo 200
L
SPEAKER
SPEAKER
R
RIGHT
WARNING:
THIS APPLIANCE
MUST BE EARTHED
ATTENTION:
CET APPAREIL DOIT
ÊTRE BRANCHÉ À
LA TERRE
INPUT
CHAIN
INPUT
TRIGGER
INPUT
OUT
7
LEFT
INPUT
MC-BUS
IN
MADE IN ENGLAND
Cyrus Stereo 200
User Instructions
Chain Output
Gain Matching
All Cyrus power amplifiers, and all power amplifier stages
in Cyrus integrated amplifiers have the same voltage gain
characteristics. This means that you can use the Stereo 200
in conjunction with any Cyrus amplifier for bi-amping, etc.
without any set-up adjustments being required.
Bi-Amplification
If your pre-amplifier only has a single set of pre outputs,
the Chain output c can be used to connect additional Cyrus
power amplifiers to each channel for Bi/Tri-amping. Such
a bi-amplified system provides the sonic benefits of totally
separate power amplification for the bass and treble units
of the loudspeakers.
Note: To set up bi-amplification, the loudspeakers must
have bi-wirable terminals to enable separate connection to
the bass and treble units.
In the bi-amplified system illustration below, a preamplifier
is connected to two Stereo 200 amplifiers, one to drive the
speaker bass (LF) units, and one to drive the treble (HF)
units. Phono input connections are shown.
Note: The Chain output is operational whether phono (RCA)
or Balanced XLR input connection is made to the Stereo
200.
Chain output and bi-amplified speaker connection
Preamplifier
OUT
L
IN
MCBUS
PRE OUT 1 PRE OUT 2
ZONE 2
OUT
HEADPHONE
R
MADE IN ENGLAND
IN-6
IN-5
IN-4
IN-3
IN-2
IN-1
USE PSX-R ONLY
IN-7
IN-8
IN-9
IN-10
IN-11
Stereo 200
L
SPEAKER
INPUT
L
RIGHT
SPEAKER
R
R
Right
speaker
terminals
WARNING:
THIS APPLIANCE
MUST BE EARTHED
ATTENTION:
CET APPAREIL DOIT
ÊTRE BRANCHÉ À
LA TERRE
CHAIN
LEFT
INPUT
INPUT
MC-BUS
TRIGGER
INPUT
OUT
IN
MADE IN ENGLAND
Stereo 200
L
SPEAKER
RIGHT
WARNING:
THIS APPLIANCE
MUST BE EARTHED
ATTENTION:
CET APPAREIL DOIT
ÊTRE BRANCHÉ À
LA TERRE
SPEAKER
R
INPUT
CHAIN
INPUT
TRIGGER
INPUT
OUT
8
LEFT
INPUT
MC-BUS
IN
MADE IN ENGLAND
Left
speaker
terminals
Cyrus Stereo 200
User Instructions
Remote Power Control (MC-BUS or 12V Trigger)
The Stereo 200 may be remotely switched to and from
Standby when used with other Cyrus components using the
Cyrus MC-BUS system.
Connecting MC-BUS
An MC-BUS (Master Control) loop is established by
connecting single phono cables from the MC-BUS output of
one unit to the MC-BUS input of another in a daisy-chain.
Complete the loop by returning the MC-BUS output of
the final component to the MC-BUS input of the first (see
example system connections below).
With MC-BUS established you can control the power function
of the system from the front panel or remote control of the
main Cyrus amplifier.
The Stereo 200 also includes a 12V trigger input for Home
Cinema, multi-room and other non-Cyrus systems that
use a 12V trigger signal to switch components to and from
Standby.
Connecting to a 12V trigger equipped system
A 3.5mm jack cable will be required to set up 12V trigger
operation. These are available in standard lengths or can be
made up to a custom length.
Once the cable is available, connect it between the 12V
Trigger input h on the back of the Stereo 200 and a 12V
trigger output on the Home Cinema receiver or other
component that is controlling system power.
Home Cinema receiver
Cyrus preamplifier
12V trigger output
MC-BUS out
MC-BUS in
Stereo 200
12V trigger input
Cyrus CD player
MC-BUS out
MC-BUS in
Cyrus streamer
MC-BUS out
MC-BUS in
Stereo 200
MC-BUS out
MC-BUS in
9
Cyrus Stereo 200
User Instructions
Connecting to the AC Mains Supply
To ensure your Stereo 200 power amplifier meets with
the requirements of the EMC directive(s), fit the supplied
ferrite clamp. The hinged clamp folds around the mains
lead and will lock together once you firmly close the shaped
channels.
20mm
Note. Fit the filter 20mm from the IEC plug as shown.
Connect the socket on the AC Power cable to the Power
inlet i on the rear panel of the amplifier. Now connect the
cable to a suitable AC power point.
The mains plug is the disconnect device for this product.
Ensure that the mains plug is always readily accessible.
10
Cyrus Stereo 200
User Instructions
OPERATION
a
b c
INPUT
Stereo 200
d
Key to the front panel drawing
1. Standby key
2. Standby indicator
3. Input indicator
4. Input selector key
11
Cyrus Stereo 200
User Instructions
Power Control
Input Indicator
When power is first applied, the amplifier will initialise, then
set to Standby.
Power operation sequence
It is always good practice to switch on the system control
amplifier (preamplifier, streamer or DAC) first, then wait for
a second before switching on the Stereo 200. This will avoid
any unwanted switch-on noise from the loudspeakers.
Follow the opposite sequence when switching off these
components, switching off the Stereo 200, then waiting a
second before switching off the control amplifier.
NOTE: The above does not apply if MC-BUS is connected for
automatic power control between Cyrus components.
Power control from the front panel
Press the STANDBY key a briefly to switch the amplifier
between operational and standby modes. The Standby
Indicator b will glow green when operational or red when
set to Standby.
First use
When the amplifier is first switched on after connection
to the mains, there will be a short delay while speaker
performance is optimised. During this time the Standby
Indicator will flash green. The indicator will stop flashing
when optimisation is complete.
NOTE: A faint noise may be heard through the speakers
during optimisation. This is normal.
Music sensing automatic power control
Music sense power control can be enabled if required.
To enable or disable Music sense, first set the amplifier
to Standby, then press and hold the STANDBY key for two
seconds. The Standby Indicator will flash red three times,
then change colour to show the status of Music sense –
orange when enabled or red when disabled.
When Music sense is enabled, the amplifier will switch on
automatically if a music signal is detected from the preamplifier, and set to Standby after 10 minutes of silence. The
STANDBY key may also be used to switch the amplifier on if
required, or to switch the amplifier back to Standby with
Music sense enabled (Standby indicator will glow orange).
A 12V trigger or any MC-BUS command cancels the Music
sense function.
The INPUT Indicator c will glow red when the output of the
Stereo 200 is muted. This occurs for a few seconds following
Standby operation or if a temporary overload condition
arises.
Selecting an Input
The front panel INPUT key d selects RCA Phono or Balanced
input connection. To change inputs, the amplifier must be
switched on.
Press and hold the INPUT key d until the INPUT indicator c
changes colour as shown.
INPUT Indicator colour Input selected
Green
Balanced
Orange
RCA Phono
NOTE: The input setting will be retained when mains power
is disconnected.
NOTE: The music sense setting will be retained when mains
power is disconnected.
12
Cyrus Stereo 200
User Instructions
TROUBLESHOOTING GUIDE
Your amplifier has a unique fault indication system to help
you to diagnose problems. Fault condition messages will be
displayed via the Standby indicator in the event of a system
fault.
If your Stereo 200 is not operating properly, disconnect
the power and check all connections using the notes in this
handbook. If problems persist, the checklist below may be
helpful.
If you are in doubt, consult your retailer.
STANDBY indicator flashing red/green
No sound from one or both speakers
Check that the preamplifier and the Stereo
200 are switched on.
Check that the correct
amplifier input is selected.
The standby lights should
be green.
The INPUT indicator will
glow green for balanced
input, orange for RCA/
phono.
Check that the
loudspeakers are
connected.
The connection at
the terminals of the
loudspeakers and the
Stereo 200 should be
checked.
The amplifier has
overheated.
STANDBY indicator flashing orange/green
The amplifier has been
overloaded or the speaker
connections have been
short-circuited.
NOTE: The Stereo 200
can detect a short-circuit
whether music is playing
or not.
Distorted sound at very low volume
The wrong input may be
selected.
The amplifier will mute
then set to Standby. The
error indication will clear
when the amplifier cools.
Press and hold the INPUT
button to change the input.
The input indicator will
light orange for phono
input or green for balanced
input.
Check that the speaker
connections are correctly
made with no possibility
of a short-circuit. To return
to normal operation, set
the amplifier to Standby to
clear the fault indication
and switch back on. If the
problem persists when
playing music, the speaker
impedance may be too low.
Ensure that only
speakers are connected
to the speaker outputs.
Switch boxes and other
accessories are not suitable
for connection.
STANDBY indicator flashing red, green or red/orange
The amplifier has detected
an error.
13
Switch off the amplifier,
disconnect it from the
mains, wait 10 seconds and
reconnect it. Check if the
problem has cleared.
If the fault indication
persists, disconnect the
amplifier and return it for
service.
Cyrus Stereo 200
User Instructions
SPECIFICATIONS
WARRANTY
Power Supply
Voltage............................................. As plate on rear of unit
The warranty should be registered on-line within 30 days
of purchase. No retailer or distributor may vary the terms
of this warranty, which is personal to the original Purchaser
and is not transferable.
Please retain the sales receipt as proof of purchase.
Warranty claims must wherever possible be made through
the retailer from whom the equipment was purchased.
This warranty excludes:
• Damage caused through neglect, accident, misuse, wear
and tear, or through incorrect installation, adjustment
or repair by unauthorised personnel. Any unauthorised
servicing will result in loss of warranty.
• Liability for damage or loss occurring in transit to or from
the purchaser.
• Consequential damage, loss or injury, arising from or in
conjunction with this equipment.
Equipment for attention under warranty should be consigned
return carriage paid. If returned equipment is found to
comply with the published specification, CYRUS reserves
the right to raise a charge.
The above conditions do not affect your statutory rights as
a consumer.
Power Consumption
Standby...................................................................... <0.5W
ON (No Signal)............................................................... 17W
Max.............................................................................. 500W
Safety Compliance.............................................................CE
EMC (230V)....................................................................... CE
EMC (115V)..................................................................... FCC
Enclosure
Dimensions (WxHxD)............................... 215 x 75 x 365mm
Weight.......................................................................... 6.9kg
Material........................................................ Die cast chassis
Audio Performance
Input Sensitivity (50W 8Ω) RCA................................. 381mV
Input Sensitivity (50W 8Ω) BAL................................. 775mV
Input Impedance (RCA)................................................ 33kΩ
Input Impedance (BAL)................................................. 33kΩ
Output Power (Continuous) 6Ω............................ 203Wrms
THD+N @1/3 full power (1kHz 8Ω)......................... <0.005%
Frequency Response (-3dB)................................<1Hz-50kHz
S/N Ratio (Ref. 170W / 8Ω)....................................... 100dBA
Chain Output (buffered)......................... (unity gain) 381mV
(ref. 381mV RCA input, 775mV Balanced input.)
WEEE
This logo means that this product is not to
be disposed of with your household waste.
This product should be handed over to a
designated collection point to be recycled.
Your cooperation in the correct disposal of this
product will contribute to the effective usage
of natural resources. For more information
on collection points, contact your disposal
service or local government administration.
Cyrus reserves the right to change all specifications without notice. E & OE
Stereo 200 English_v0.10
14
Cyrus Audio Ltd., Ermine Business Park, Huntingdon, PE29 6XY, U.K.