trifix - Baby On The Move

PRODUCT OVERVIEW
13
03
04
14
06
15
07
05
16
08
09
17
10
11
02
TWO-YEAR WARRANTY
To ensure the full protective effect of the child safety seat:
• In the event of an accident with an impact speed above 10
km/h it is possible that the child safety seat may have been
damaged, but that the damage may not be immediately
obvious. In this case the child safety seat must be replaced.
Please dispose of it properly.
• Regularly check all important parts for damage. Make sure
that the mechanical components in particular are all in perfect working order.
• To prevent damage, ensure that the child safety seat does
not become jammed between hard objects (car door, seat
runners etc.).
• Always have the child safety seat checked if it has been damaged (e.g. if it is dropped).
• Never lubricate or oil parts of the child seat.
For this child safety seat we offer a 2-year warranty against manufacturing or
material defects. The warranty period is effective from the day of purchase.
The warranty covers only child safety seats which have been handled properly
and which have been sent to us in a clean and proper condition.
12
01
02
03
04
05
06
ISOFIX attachment points (car)
ISOFIX insert guides
Headrest
Harness retainer
Harness buckle
Shoulder pads
07
08
09
10
11
12
Tested and certified according
to ECE* R 44/04
BRITAX RÖMER
child safety seat
TRIFIX
Group
Body weight
1
9 bis 18 kg
Shoulder straps
Adjusting button
Adjustment strap
Recline handle
ISOFIX unlocking buttons
ISOFIX indicators
13
14
15
16
17
18
Please observe the waste disposal regulations in your country.
Adjusting ring of the headrest
Top Tether
User guide compartment
Fabric loop
ISOFIX locking arms
Seat shell
The child safety seat has been designed, tested and certified according to the requirements of the European
Standard for Child Safety Equipment (ECE R 44/04). The test mark E (in a circle) and the certification number
are located on the orange certification sticker (sticker on the child safety seat).
• This certification will be invalidated if you make any modifications to the child safety seat.
• The TRIFIX child safety seat must only be used to secure your child in the vehicle. It must never be used as a
seat or toy in the home.
Disposal of packaging
Container for cardboard
Cover
Residual waste, thermal utilisation
Plastic parts
In accordance with the labelling in the
designated container
Metal parts
Container for metals
Harness straps
Container for polyester
Buckle &latch
Residual waste
Care for the harness buckle
It is vital for the safety of your child that the harness buckle works correctly.
Malfunctions of the harness buckle are usually caused by accumulations of dirt
or foreign bodies:
• The buckle latches are ejected only slowly when the red release button is
pressed.
• The buckle latches will no longer lock home (i.e. they are ejected again if you
try to push them in).
• The buckle latches engage without an audible „click“.
• The buckle latches are difficult to insert (you feel resistance).
• The buckle only opens if extreme force is applied.
Remedy
wash out the harness buckle so that it functions properly once again:
washing machine‘s cycle for delicate items (30 °C). Please observe the
instructions on the washing label of the cover.
• The plastic parts can be cleaned using soapy water. Do not use harsh
cleaning agents (such as solvents).
• The harnesses can be washed in lukewarm soapy water.
Caution: Never remove the buckle latches 21 from the straps.
• The shoulder pads can be washed in lukewarm soapy water.
Removing the cover
03
31
05
Cleaning the harness buckle
20
10
22
Use, care and maintenance
The child safety seat must be used in accordance with the user instructions.
We point out expressly that only genuine accessories and replacement parts
must be used.
BRITAX EXCELSIOR LIMITED
1 Churchill Way West
Andover
Hampshire SP10 3UW
United Kingdom
t: +44 (0) 1264 333343
f: +44 (0) 1264 334146
e: helpline@uk.britaxeurope.com
www.britax.eu
t: +49 (0) 731 9345 0
f: +49 (0) 731 9345 210
e: info@de.britaxeurope.com
www.roemer.eu
USE IN THE VEHICLE
CARE AND MAINTENANCE
20
What is covered by the warranty?
Fabrics: All of our fabrics meet very high requirements with regard to colour
fastness when exposed to UV radiation. Nevertheless, all fabrics fade when
exposed to UV radiation. This is not a material defect, but rather a normal sign
of wear which is not covered by the warranty.
Buckle: Buckle malfunctions are often due to accumulations of dirt or foreign
bodies which may stop the buckle from working properly. If this happens, the
buckle can be cleaned, olease follow the procedure described in your user
instructions.
Please contact your retailer immediately in the event of a warranty claim. He or
she will give you the advice and support you need. When processing claims,
product-specific depreciation rates will be applied. Please refer to our General
Terms and Conditions which are available from your retailer.
BRITAX RÖMER
Kindersicherheit GmbH
Blaubeurer Straße 71
D-89077 Ulm
Germany
*ECE = European Standard for Child safety Equipment
05
The Warranty does not cover:
• natural signs of wear and damage resulting from excessive stress
• damage resulting from inappropriate or improper use
31
1. Open the harness buckle 05 (press the red button).
2. Pull the elastic loop over the harness buckle 05 .
2. Open the Velcro fastener on the crotch pad 20 and take off the crotch pad
from the cover.
3. Slide the metal plate 22 which is used to fasten the harness buckle 05 to
the seat shell up on its edge through the strap slot 31 .
4. Soak the harness buckle 05 in warm water with dishwashing liquid for at
least an hour. Then rinse and dry it thoroughly.
Cleaning
Please be sure to use only genuine Britax/RÖMER replacement seat covers,
as the seat cover is an integral part of the child safety seat which plays an
important role in ensuring that the system works properly. Replacement
seat covers are available from your retailer.
• The child seat must not be used without its cover.
• The cover can be removed and washed with a mild detergent using the
1. Press the recline handle 10 upwards and slide the seat shell 18 to the rear
into the upright position.
2. Loosen the harness straps as far as possible.
3. Open the harness buckle 05 (press the red button).
4. Open the Velcro fastener on the crotch pad 20 .
5. Slide the headrest 03 to its lowest position.
6. Remove the cover of the headrest 31 .
7. Open the poppers on the left and right of the rear part of the cover.
8. Fold the rear part of the cover onto the seat surface.
9. Thread the harness straps through the cutout in the cover.
10.Unhook both of the elastic hoops at the rear, upper edge of the seat shell.
11. Unhook the elastic seam of the cover under the edge of the seat shell.
TIP: Start at the handles on the side and at the upper edge of the seat shell.
12.Pull the cover up and over the bezel of the strap adjuster.
13.Feed out the harness buckle 05 and the end of the strap from the cover.
14.Pull the cover upwards a little and then put it with the cutout over the headrest 03 .
Re-fitting the Cover:
Simply follow the steps in the opposite order.
Caution: Check that the harness straps are not twisted and that they have
been correctly inserted in the belt slots on the cover.
Please observe the instructions on the use of child restraint systems described in
your vehicle owner’s manual.
9 - 18kg
The seat may be used in all vehicles equipped with the ISOFIX and Top Tether
anchoring systems. Please consult your vehicle owner’s manual for information
about the Top Tether anchoring points and the seats which are approved for child
safety seats in the weight class 9-18 kg.
In the direction of travel
Yes
Against the direction of travel
No 1)
TRIFIX
On seats featuring:
ISOFIX attachments (between
seat surface and backrest) and
Top Tether anchoring points (for Yes 2)
example on the parcel shelf, on
the floor or behind the backrest)
User Instructions
(Please observe the applicable regulations in your country)
1) Use is permitted on a rearward-facing vehicle seat (e.g. in a van or minibus)
only if the vehicle seat is also approved for use by adults. The seat must not be
positioned anywhere where it is in range of an airbag which is being deployed.
2) If there is a front airbag: Slide the passenger seat a long way back and refer to
any instructions in vehicle owner’s manual.
NEXT CHILD SAFETY SEATS
BRITAX RÖMER
Child safety seats
KID
KID plus
KIDFIX
KIDFIX SICT
Testing and certification in accordance with ECE R 44/04
Group
Body weight
2-3
2-3
2-3
2-3
15 - 36 kg
15 - 36 kg
15 - 36 kg
15 - 36 kg
GB
01
18
CARE INSTRUCTIONS
Take the time to carefully read through these instructions, and always keep them ready to hand in the designated pocket on the child seat.
For the protection of all vehicle occupants
In the case of an emergency stop or an accident, persons or objects which are not properly secured in the car can cause injury to other vehicle
occupants. For this reason, please always check that...
• the backrests of the vehicle seats are locked (e.g. that the latch on a folding rear seat bench is engaged).
• all heavy or sharp-edged objects in the vehicle (e.g. on the parcel shelf) are secured.
• all persons in the vehicle have their seatbelts fastened.
• the child safety seat is always secured in the car via the ISOFIX anchoring and the Top Tether, even when there is no child in the seat.
For the protection of your child
• The more snugly the harness fits over your child‘s body, the safer your child will be.
• Please do not ever leave your child unattended in the child safety seat in the vehicle.
A
INSTALLATION
• Use on the rear seat:
Move the front seat forward far enough that you child‘s feet cannot hit the backrest of the front seat (to prevent risk of injury).
• The child safety seat can get hot in direct sunshine. Caution: Children‘s skin is delicate and could be injured as a result. Protect the child
seat against intensive direct sunlight when it is not currently in use.
• Only allow your child to enter and exit the vehicle on the pavement side.
• Make stops during longer journeys to give your child an opportunity to run about and play.
To protect your vehicle
Some vehicle seat coverings made of more delicate materials (e.g. velour, leather, etc.) may develop wear marks when child seats are used.
For optimum protection of your seat covers, we recommend using the BRITAX RÖMER Car Seat Protector, which is available from our range
of accessories.
B
C
E
D
26
F
14
Preparatory work
14
01
02
28
1. If your vehicle is not equipped with the ISOFIX insert guides as
standard, clip the two insert guides 02 which are included with the
seat* with the cut-out facing upwards onto the two ISOFIX attachment points 01 of your vehicle.
TIP: The ISOFIX attachment points are located between the surface
and the backrest of the vehicle seat.
2. Move the head restraint on the vehicle seat to the upper position.
16 17
click!
1. Pull the grey fabric loop 16 to pull
out both locking arms 17 until you
hear a clicking sound which indicates they are fully engaged.
I
H
06
2. Take the Top Tether 14 from the
user guide compartment 15 and
lay it over the child safety seat.
4. Grasp the child safety seat with
both hands and slide the two
locking arms 17 firmly into the
insert guides 02 until the locking
arms engage with a clicking noise
on both sides.
Caution: The locking arms are
only correctly engaged if both
of the ISOFIX indicators 12 are
completely green.
K
J
08
1 cm
5. Push the child safety seat with a
substantial amount of force as far
back as it will go.
6. Shake the child safety seat to
make sure it is safely attached
and re-check to the ISOFIX indicators 12 to make sure that both
of them are completely green
L
7. Take the Top Tether 14 and press
the metal tongue 28 away from
the strap to lengthen the strap and
pull the Top Tether 14 by the snap
hook 26 until it makes a V-shape.
M
13
10. Tension the strap of the Top
Tether 14 until the tension
indicator 27 turns green and the
Top Tether 14 is tightly tensioned.
N
21
04
07
05
05
9. Hook the snap hook 26 into the
Top Tether anchoring point recommended in your vehicle owner‘s
guide.
8. Guide the Top Tether 14 on the
left and right-hand sides past the
headrest.
03
21
07
12
12
03
14
27
15
3. Place the child safety seat facing
in the direction of travel on the
vehicle seat.
* The insert guides make it easier to install the child safety seat with the aid of the ISOFIX attachment points and prevent damage to the seat covering. When not in use, they
should be removed and stored in a safe place. On vehicles with a folding backrest the
insert guides must be removed before the backrest is folded.
Any problems which occur are usually caused by dirt or foreign objects on the insert
guides and on the hooks. Clean off any dirt or foreign objects to remedy this type of
problem.
G
click!
14
Caution: Check that the child
safety seat is correctly attached
11. Press the adjusting button 08
and at the same time pull both
shoulder straps 07 forwards.
Caution: Do not pull on the shoulder pads 06 .
12. Open the harness buckle 05
(press the red button).
13. Pull the shoulder straps 07 to
one side and put the two buckle
latches 21 into the harness
retainer 04
14. Make sure that the buckle 05 is
folded forwards and place your
child in the child safety seat.
15. Put the shoulder straps 07 over
the shoulders of your child.
A correctly adjusted headrest 03
ensures optimal protection for your
child in the safety seat:
The headrest 03 must be adjusted
so that the shoulder straps 07 are at
the same level as your child’s shoulders or slightly above.
17. Pull the adjusting ring of the head
rest 13 upwards
18. Move the head rest 03 to the
correct shoulder strap height and
check that it is properly engaged
by lightly sliding the head rest 03
downwards.
28
19. Guide the two buckle latches 21
together and engage them before
putting them into the harness
buckle 05 - this should make a
clicking noise.
09
20. Pull on the adjusting strap 09
until the harness lies flat and
is close against your child‘s
body.
Caution: Pull out the adjusting strap to the front.
Caution: The hip straps 28
must be positioned as low as
possible over your child‘s hips.
Caution: The shoulder straps 07
must not be twisted or swapped.
For the safety of your child, before every journey in the car check that...
• the child safety seat is engaged on both sides with the ISOFIX locking arms 17 in the ISOFIX attachment points 01 and that both ISOFIX
indicators 12 are completely green;
• the child safety seat is securely fastened;
• the Top Tether 14 is tightly tensioned over the backrest of the car seat and the tension indicator 27 is green;
• the straps of the child safety seat are close to the body without constricting the child;
• the shoulder straps 07 are correctly adjusted and the straps are not twisted;
• the shoulder pads 06 are in the right position on your child‘s body;
• the buckle latches 21 are engaged in the harness buckle 05 .
Caution: If your child attempts to open the grey ISOFIX locking buttons 11 or the harness buckle 05 , make sure to stop at the earliest opportunity. Check that the child safety seat is correctly attached and make sure that your child is properly secured. Teach your child about the
dangers involved.
Removing the child safety seat with ISOFIX
1. Loosen the Top Tether 14
2. Unhook the snap hook 26 from the anchoring point and lay the Top Tether 14 to the front over the child safety seat
3. Press on the grey ISOFIX unlocking buttons on the left and right-hand side of the seat shell 18 .
The ISOFIX locking arms 17 will release and the two ISOFIX indicators 12 will change colour to red.
4. Pull the seat forwards and stow the Top Tether 14 back in the user guide compartment 15 .
5. Slide the ISOFIX locking arms 17 back into the seat shell 18
A rattling noise is produced when the locking arms are pushed back in.
TIP: The locking arms are protected against damage when they are pushed back into the seat base.
Caution: Remove the child safety seat from the vehicle.The child safety seat must never be transported in the car if it is not properly secured.
Download PDF
Similar pages