Installation/Operation for Clothes Dryer

Installation/Operation
Clothes Dryer
Electric and Gas Models
TIONS
INSTRUC
ING
)
OPERAT
(heat setting,
PRESS
Fabric Type
PERM
heat)
1. Select
NORMAL, FLUFF (no
DELICATE,
Clothes.
2. Load
.
Start.
Coin(s)/Card
and Push
3. Insert
Close Door
Dryer Open Door.
4. To Start
Cycle Dryer During
Push Start.
5. To Stop
Door and
- Close
t Dryer
When
6. To Restar
Complete
Cycle is Goes Off.
Drying
Panel Light
ATE
DELIC
PERM
PRESS
AL
NORM
FLUFF
(NO HEAT)
IN USE
CLEA
SELECTOR
FABRIC
PUSH
N LINT
FILTE
R AFTE
R EACH
LOAD
504210
T
TO STAR
D709I
Para bajar una copia de estas instrucciones en español, visite www.comlaundry.com.
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
www.comlaundry.com
Part No. 510977R7
January 2009
WARNING
FOR YOUR SAFETY, the information in this manual must be followed to minimize
the risk of fire or explosion or to prevent property damage, personal injury or
death.
W033
• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or
any other appliance.
• WHAT TO DO IF YOU SMELL GAS:
– Do not try to light any appliance.
– Do not touch any electrical switch; do not use any phone in your building.
– Clear the room, building or area of all occupants.
– Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s
instructions.
– If you cannot reach your gas supplier, call the fire department.
• Installation and service must be performed by a qualified installer, service agency or the gas
supplier.
W052
•
IMPORTANT: Purchaser must consult the local gas supplier for suggested instructions to be followed if the
dryer user smells gas. The gas utility instructions plus the SAFETY and WARNING note directly above
must be posted in a prominent location near the dryer for customer use.
WARNING
• Installation of unit must be performed by a qualified installer.
• Install clothes dryer according to manufacturer’s instructions and local codes.
• DO NOT install a clothes dryer with flexible plastic venting materials. If flexible metal (foil
type) duct is installed, it must be of a specific type identified by the appliance manufacturer
as suitable for use with clothes dryers. Refer to section on connecting exhaust system.
Flexible venting materials are known to collapse, be easily crushed, and trap lint. These
conditions will obstruct clothes dryer airflow and increase the risk of fire.
W729R1
FOR YOUR SAFETY
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or
any other appliance.
W053
The following information applies to the state of Massachusetts, USA.
●
This appliance can only be installed by a Massachusetts licensed plumber or gas fitter.
●
This appliance must be installed with a 36 inch (91 cm) long flexible gas connector.
●
A “T-Handle” type gas shut-off valve must be installed in the gas supply line to this appliance.
This appliance must not be installed in a bedroom or bathroom.
510977
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
1
Table of
Contents
Safety Information..............................................................................
Explanation of Safety Messages...........................................................
Important Safety Instructions ...............................................................
4
4
4
Installation...........................................................................................
Dimensions ...........................................................................................
Additional Security...............................................................................
Slide Extension .....................................................................................
Timer Cams ..........................................................................................
Coin Slide Guards.................................................................................
Before You Start ...................................................................................
Tools ................................................................................................
Installing the Dryer ...............................................................................
Step 1: Position and Level the Dryer ...............................................
Step 2: Connect Dryer Exhaust System ...........................................
Exhaust Direction.............................................................................
Exhaust System ................................................................................
Multi-Dryer Installation Exhaust Requirements ..............................
Step 3: (Gas Dryer Only) Connect Gas Supply Pipe .......................
Step 4: (Electric Dryer Only) Connect Electrical Plug ....................
Step 5: Reverse Door, if Desired .....................................................
Step 6: Wipe Out Inside of Dryer ....................................................
Step 7: Plug In the Dryer .................................................................
Step 8: Recheck Steps 1-7................................................................
Step 9: Check Heat Source ..............................................................
6
6
7
7
7
8
9
9
9
9
11
12
13
14
16
17
23
24
24
25
25
Operation.............................................................................................
Operation Instructions for Electromechanical Dryers ..........................
Step 1: Clean Lint Filter...................................................................
Step 2: Load Laundry.......................................................................
Step 3: Close Loading Door.............................................................
Step 4: Set Fabric Selector ...............................................................
Step 5: Start Dryer ...........................................................................
Operation Instructions for Electronic Display Control Dryers.............
Step 1: Clean Lint Filter...................................................................
Step 2: Load Laundry.......................................................................
Step 3: Close Loading Door.............................................................
Step 4: Set Fabric Selector ...............................................................
Step 5: Insert Coin(s) or Card ..........................................................
Step 6: Start Dryer ...........................................................................
Indicator Lights ................................................................................
Operation Instructions for MDC Dryers...............................................
Step 1: Clean Lint Filter...................................................................
Step 2: Load Laundry.......................................................................
Step 3: Close Loading Door.............................................................
Step 4: Set Fabric Selector ...............................................................
Step 5: Insert Coin(s) or Card ..........................................................
Step 6: Start Dryer ...........................................................................
Indicator Lights ................................................................................
27
27
27
27
27
28
28
29
29
29
29
30
30
30
31
32
32
32
32
33
33
33
34
© Copyright 2009, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
2
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
510977
Operation Instructions for NetMaster Dryers .......................................
Step 1: Clean Lint Filter...................................................................
Step 2: Load Laundry.......................................................................
Step 3: Close Loading Door.............................................................
Step 4: Set Fabric Selector ...............................................................
Step 5: Insert Coin(s) or Card ..........................................................
Step 6: Start Dryer ...........................................................................
Indicator Lights ................................................................................
35
35
35
35
36
36
36
37
Maintenance ........................................................................................
Lubrication............................................................................................
Care of Your Dryer...............................................................................
Dryer Interior ...................................................................................
Cabinet .............................................................................................
Control Panel ...................................................................................
Exhaust System ................................................................................
Lint Filter ..............................................................................................
Motor Overload Protector.....................................................................
For Energy Conservation......................................................................
38
38
38
38
38
38
38
38
39
39
Troubleshooting .................................................................................. 40
Contact Information........................................................................... 41
Installer Checklist...............................................................
510977
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Back Cover
3
Safety Information
Explanation of Safety Messages
Important Safety Instructions
Throughout this manual and on machine decals, you
will find precautionary statements (“DANGER,”
“WARNING,” and “CAUTION”) followed by specific
instructions. These precautions are intended for the
personal safety of the operator, user, servicer, and
those maintaining the machine.
Save These Instructions
DANGER
Indicates an imminently hazardous
situation that, if not avoided, will cause
severe personal injury or death.
WARNING
Indicates a hazardous situation that, if not
avoided, could cause severe personal
injury or death.
CAUTION
WARNING
To reduce the risk of fire, electric shock,
or injury to persons when using your
dryer, follow these basic precautions:
W034
1. Read all instructions before using the dryer.
2. Refer to the GROUNDING INSTRUCTIONS in
the INSTALLATION manual for the proper
grounding of the dryer.
3. Do not dry articles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, dry-cleaning solvents, other flammable
or explosive substances as they give off vapors
that could ignite or explode.
4. Do not allow children to play on or in the dryer.
Close supervision of children is necessary when
the dryer is used near children. This is a safety
rule for all appliances.
Indicates a hazardous situation that, if not
avoided, may cause minor or moderate
personal injury or property damage.
5. Before the dryer is removed from service or
discarded, remove the door to the drying
compartment.
Additional precautionary statements (“IMPORTANT”
and “NOTE”) are followed by specific instructions.
6. Do not reach into the dryer if the cylinder is
revolving.
IMPORTANT: The word “IMPORTANT” is used
to inform the reader of specific procedures where
minor machine damage will occur if the procedure
is not followed.
7. Do not install or store the dryer where it will be
exposed to water and/or weather.
NOTE: The word “NOTE” is used to communicate
installation, operation, maintenance or servicing
information that is important but not hazard
related.
8. Do not tamper with the controls.
9. Do not repair or replace any part of the dryer, or
attempt any servicing unless specifically
recommended in the user-maintenance
instructions or in published user-repair
instructions that you understand and have the
skills to carry out.
10. Do not use fabric softeners or products to
eliminate static unless recommended by the
manufacturer of the fabric softener or product.
11. To reduce the risk of fire, DO NOT DRY plastics
or articles containing foam rubber or similarly
textured rubberlike materials.
12. ALWAYS clean the lint filter after every load. A
layer of lint in the filter reduces drying efficiency
and prolongs drying time.
4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
510977
Safety Information
13. Keep area around the exhaust opening and
adjacent surrounding area free from the
accumulation of lint, dust and dirt.
14. The interior of the dryer and the exhaust duct
should be cleaned periodically by qualified
service personnel.
15. If not installed, operated and maintained in
accordance with the manufacturer’s instructions
or if there is damage to or mishandling of this
product’s components, use of this product could
expose you to substances in the fuel or from fuel
combustion which can cause death or serious
illness and which are known to the State of
California to cause cancer, birth defects or other
reproductive harm.
16. Dryer will not operate with the loading door
open. DO NOT bypass the door safety switch by
permitting the dryer to operate with the door
open. The dryer will stop tumbling when the door
is opened. Do not use the dryer if it does not stop
tumbling when the door is opened or starts
tumbling without pressing the START
mechanism. Remove the dryer from use and call
the service person.
17. Do not put articles soiled with vegetable or
cooking oil in the dryer, as these oils may not be
removed during washing. Due to the remaining
oil, the fabric may catch on fire by itself.
18. To reduce the risk of fire, DO NOT put clothes
which have traces of any flammable substances
such as machine oil, flammable chemicals,
thinner, etc., or anything containing wax or
chemicals such as in mops and cleaning cloths, or
anything dry-cleaned at home with a drycleaning solvent in the dryer.
19. Use the dryer only for its intended purpose,
drying clothes.
20. Always disconnect the electrical power to the
dryer before attempting service. Disconnect the
power cord by grasping the plug, not the cord.
21. If supply cord is damaged, it must be replaced by
a special cord or assembly available from the
manufacturer or its service agent.
22. Install this dryer according to the
INSTALLATION INSTRUCTIONS. All
connections for electrical power, grounding and
gas supply must comply with local codes and be
made by licensed personnel when required. Do
not do it yourself unless you know how!
23. Remove laundry immediately after the dryer
stops.
24. Always read and follow manufacturer’s
instructions on packages of laundry and cleaning
aids. Heed all warnings or precautions. To reduce
the risk of poisoning or chemical burns, keep
them out of reach of children at all times
(preferably in a locked cabinet).
25. Do not tumble fiberglass curtains and draperies
unless the label says it can be done. If they are
dried, wipe out the cylinder with a damp cloth to
remove particles of fiberglass.
26. ALWAYS follow the fabric care instructions
supplied by the garment manufacturer.
27. Never operate the dryer with any guards and/or
panels removed.
28. DO NOT operate the dryer with missing or
broken parts.
29. DO NOT bypass any safety devices.
30. Failure to install, maintain, and/or operate this
machine according to the manufacturer’s
instructions may result in conditions which can
produce bodily injury and/or property damage.
IMPORTANT: Solvent vapors from dry-cleaning
machines create acids when drawn through the
heater of the drying unit. These acids are corrosive
to the dryer as well as to the laundry load being
dried. Be sure make-up air is free of solvent vapors.
IMPORTANT: Have your dryer installed properly.
Don’t do it yourself unless you know how!
NOTE: The WARNING and IMPORTANT
SAFETY INSTRUCTIONS appearing in this
manual are not meant to cover all possible
conditions and situations that may occur. Common
sense, caution and care must be exercised when
installing, maintaining, or operating the dryer.
Always contact your dealer, distributor, service agent
or the manufacturer about any problems or conditions
you do not understand.
510977
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5
Installation
Dimensions
*4.0 in. (10.2 cm)
8.0 in.
(20.3 cm)
23.5 in.
(59.7 cm)
28 in.
(71.1 cm)
*15.44 in.
(39.2 cm)
*43.2 in. (109.7 cm)
*4.5 in. (11.4 cm)
2.0 in.
(5.1 cm)
15.4 in.
(39.1 cm)
0.4 in.
(1.0 cm)
*Electromechanical Models 39.38 in. (100 cm)
*Electronic Control Models 36.94 in. (93.83 cm)
26.9 in.
(68.3 cm)
ELECTRIC MODELS
DRY2222N
DRY2222N
*With leveling legs turned into base.
8.0 in.
(20.3 cm)
0.4 in.
(1.0 cm)
28 in.
(71.1 cm)
*Electromechanical Models 39.38 in. (100 cm)
*Electronic Control Models 36.94 in. (93.83 cm)
2.3 in.
(6 cm)
15.4 in.
(39.1 cm)
23.5 in.
(59.7 cm)
*15.44 in. (39.2 cm)
*2.8 in. (7 cm)
*4.0 in. (10.2 cm)
*4.5 in. (11.4 cm)
*43.2 in. (109.7 cm)
2.0 in.
(5.1 cm)
1
26.9 in.
(68.3 cm)
DRY2251N
GAS MODELS
DRY2251N
*With leveling legs turned into base.
1
3/8" NPT Gas Connection
NOTE: Side, rear and bottom exhaust openings are
4 inch (10.2 cm) ducting. Gas models cannot be
vented out left side of cabinet because of burner
housing.
6
IMPORTANT: The dryer should have sufficient
clearance around it for needed ventilation and for
the ease of installation and servicing. For maximum
drying performance, we recommend that more
clearance be allowed around the dryer than the
clearances that are listed throughout this manual.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
510977
Installation
Additional Security
Torx security screws are available (as optional
equipment at extra cost) for securing lower access
panel to dryer base. Order part number 62853.
NOTE: Adjust ratchet wheel and timing cam to
“OFF” position prior to putting dryer into use.
Refer to Figure 1 for proper position.
1
A Torx bit, part number 282P4, is available (as
optional equipment at extra cost) for installing the
Torx security screws.
A Torx bit holder, part number 24161, is available (as
optional equipment at extra cost) to be used with the
Torx bit.
6
Slide Extension
5
(Coin Slide Models Only)
4
Remove slide extension, screws and lockwashers from
the accessories bag and install the extension on the top
of the coin slide.
IMPORTANT: Slide extension must be attached to
top side of the coin slide to make it long enough to
activate the accumulator.
NOTE: This dryer, as shipped from the factory,
does not include the coin slide, coin drawer, lock or
keys. This coin slide kit (or parts) must be ordered,
at extra cost, according to the purchaser’s
requirements direct from the coin kit manufacturer
of your choice.
Timer Cams
(Coin Slide Models Only)
The dryer timers are factory equipped with a 45
minute timing cam. If this drying time is not suitable
to your installation, the following cams can be found
in the accessories bag.
2
3
D775I
7
D775I
1
2
3
4
5
6
7
Retaining Prongs
Timing Cam
Notch
Levers
Off Position
Ratchet Wheel
On Position
Figure 1
ELECTRIC DRYERS
1-53242 Cam (30 Minutes)
1-53240 Cam (60 Minutes)
GAS DRYERS
1-53242 Cam (30 Minutes)
A 60 minute timing cam, Part No. 53240, is available
for the gas dryer as optional equipment at extra cost.
To change the timing cam:
1. Align notch in cam with a tooth on ratchet wheel.
2. Squeeze the ends of the two timing cam prongs
together.
3. Carefully lift timing cam off post.
510977
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
7
Installation
Coin Slide Guards
(Coin Slide Models Only)
Using sheet metal screws from accessories bag, install
coin slide guard, to front of control cabinet. Refer to
Figure 2.
1
OPERATING INSTRUCTIONS
PERM PRESS
1. Select Fabric Type (heat setting)
NORMAL, PERM PRESS,
DELICATE, FLUFF (no heat)
DELICATE
2. Load Clothes.
FLUFF
(NO HEAT)
NORMAL
3. Insert Coin(s)/Card.
IN USE
FABRIC SELECTOR
4. To Start Dryer - Close Door and Push Start.
5. To Stop Dryer During Cycle - Open Door.
6. To Restart Dryer - Close Door and Push Start.
Drying Cycle is Complete When
Panel Light Goes Off.
PUSH TO START
CLEAN LINT FILTER AFTER EACH LOAD
504210
2
D789I
1
Coin Slide Guard
2
D789I
Sheet Metal Screws
Figure 2
NOTE: Coin slides and coin drawers are shown for
illustration only. You must obtain them locally.
8
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
510977
Installation
Before You Start
No other fuel burning appliance should be installed in
the same closet with the dryer.
Tools
For most installations, the basic tools you will need
are:
1
2
The dryer must not be installed or stored in an area
where it will be exposed to water and/or weather.
The dryer needs sufficient clearance and an adequate
air supply for proper operation and ventilation, and for
easier installation and servicing. (Minimum clearances
are shown in Figure 4).
Place the dryer in position, and adjust the legs until the
dryer is level from side to side and front to back.
Leveling legs can be adjusted from inside the dryer
with a 1/4 in. driver. All four legs must rest firmly on
the floor so the weight of the dryer is evenly
distributed. The dryer must not rock.
3
5
1
4
2
3
D818I
1
2
3
4
5
Wrench
Screwdrivers
Level
Teflon Tape
Duct Tape
CTIONS
ING INSTRU
OPERAT
(heat setting)
PRESS,
Fabric Type
PERM
heat)
1. Select
NORMAL, FLUFF (no
DELICATE,
Clothes.
2. Load
.
Start.
Coin(s)/Card
and Push
3. Insert
Close Door
Dryer Open Door.
Cycle Start.
Dryer During
and Push
Close Door
Dryer When
Complete
Cycle is Goes Off.
Drying
Panel Light
4. To Start
5. To Stop
6. To Restart
DELICATE
PERM
PRESS
FLUFF
(NO HEAT)
NORMAL
FABRIC
PUSH
IN USE
CLEAN
R
SELECTO
LINT FILTER
AFTER
EACH
LOAD
504210
TO START
Figure 3
NOTE: An 8 in. (20.32 cm) coin drawer is required
for coin operated MDC and NetMaster models.
D710I
4
WARNING
D710I
1
2
3
4
Any disassembly requiring the use of
tools must be performed by a suitably
qualified service person.
Dryer Base
Leveling Leg
Level
Rubber Cup
W299
Figure 4
Installing the Dryer
Install the four rubber feet (in accessories bag).
IMPORTANT: In mobile home installations, gas
dryers MUST be permanently attached to the floor
at the time of installation. Order No. 526P3 Hold
Down Kit (available at extra cost) for a
manufactured (mobile) home installation. Follow
the instructions supplied with the kit.
Select a location with a solid floor. Dryers installed in
residential garages must be elevated 18 inches (46 cm)
above the floor.
Installation of unit must conform to the Manufactured
Home Construction and Safety Standards, Title 24
CF4, Part 32-80 or Standard CAN/CSA-Z240 MH.
Step 1: Position and Level the Dryer
Install dryer before washer. This allows room for
attaching exhaust duct.
510977
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9
Installation
B
E
D
A
A
*42"
(107 cm)
C
A
1
SIDE VIEW
FRONT VIEW
(w/o Closet Door)
Area
Description
Free Standing/Alcove Installation
A
Dryer sides and rear clearance
0 in. (0 cm)
B
Dryer top clearance
12 in. (30.5 cm)
C
Dryer front clearance
Not Applicable
D
Exhaust duct clearance to combustible material
2 in. (5.1 cm)
E
Weather hood to ground clearance
12 in. (30.5 cm)
(Minimum clearances are shown.)
D817I
* NOTE: For new installations, locate top of wall vent 42 inches (107 cm) above floor to make venting easier
to connect.
1
Outer wall of enclosure
Figure 5
10
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
510977
Installation
Step 2: Connect Dryer Exhaust System
WARNING
To reduce the risk of fire and combustion
gas accumulation the dryer MUST be
exhausted to the outdoors.
IMPORTANT: Installing in-line filters or lint
collectors will cause increased static pressure.
Failure to maintain the secondary lint system will
decrease dryer efficiency and may void machine
warranty.
●
DO NOT use plastic or thin foil ducting. Rigid
metal duct is recommended.
W604
To reduce the risk of fire and the
accumulation of combustion gases, DO NOT
exhaust dryer air into a window well, gas
vent, chimney or enclosed, unventilated
area, such as an attic, wall, ceiling, crawl
space under a building or concealed space
of a building.
W045
WARNING
D740I
This gas appliance contains or produces a
chemical or chemicals which can cause
death or serious illness and which are
known to the State of California to cause
cancer, birth defects, or other reproductive
harm. To reduce the risk from substances in
the fuel or from fuel combustion, make sure
this appliance is installed, operated, and
maintained according to the instructions in
this manual.
DO
D740I
Figure 6
●
Locate dryer so exhaust duct is as short as
possible.
●
Be certain old ducts are cleaned before installing
your new dryer.
●
Use 4 inch (10.2 cm) diameter rigid or flexible
metal duct.
●
The male end of each section of duct must point
away from the dryer.
●
Use as few elbows as possible.
●
Use duct tape or pop-rivets on all duct joints. DO
NOT use sheet metal screws or fasteners on
exhaust pipe joints which extend into the duct
and catch lint.
●
Ductwork that runs through unheated areas must
be insulated to help reduce condensation and lint
build-up on pipe walls.
●
Install backdraft dampers in multi-dryer
installations.
●
In mobile home installations, dryer exhaust duct
must be secured to mobile home structure.
●
Dryer exhaust duct MUST NOT terminate under
mobile home.
●
Dryer exhausts 220 cfm (measured at back of
dryer).
●
DO NOT install flexible duct in concealed
spaces, such as a wall or ceiling.
W115
To reduce the risk of fire, DO NOT use
plastic or thin foil ducting to exhaust the
dryer.
W354
To reduce the risk of fire, the exhaust duct
and weather hood MUST be fabricated of a
material that will not support combustion.
Rigid or flexible metal pipe is recommended
for a clothes dryer.
W048
WARNING
To reduce the risk of fire due to increased
static pressure, we do not recommend
installation of in-line secondary lint filters
or lint collectors. If secondary systems
are mandated, frequently clean the
system to assure safe operation.
W749
510977
DON’T
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
11
Installation
●
Static pressure in exhaust duct should not be
greater than .6 inches water column (1.5 cm),
measured with manometer placed on exhaust
duct two feet (61 cm) from dryer (check with
dryer running and no load). In multi-dryer
installations, all dryers connected to the main
collector duct should be operating when pressure
is checked.
●
Exhausting dryer in hard-to-reach locations can
be done by installing 521P3 Flexible Metal Vent
Kit (available as optional equipment at extra
cost).
●
Sufficient make-up air must be supplied to
replace the air exhausted by the dryer. The free
area of any opening for outside air must be at
least 40 in.2 (260 cm2).
●
Energy efficient buildings with low air
infiltration rates should be equipped with an air
exchanger that can accommodate on demand
make-up air needs in the laundry room. These
devices can be obtained through your building
contractor or building material suppliers.
●
Do not draw make-up air from a room containing
a gas fired water heater, a dry cleaner or a hair
salon.
●
Failure to exhaust dryer properly will void
warranty.
Exhaust Direction
The dryer can be exhausted to the outdoors through the
back, left, right or bottom of the dryer. EXCEPTION:
Gas dryers cannot be vented out the left side
because of the burner housing.
Dryer is shipped from factory ready for rear exhaust.
Exhausting the dryer through sides or bottom can be
accomplished by installing a Directional Exhaust Kit,
528P3, available as optional equipment at extra cost.
NOTE: Venting materials are not supplied with the
dryer (obtain locally).
IMPORTANT: DO NOT block the airflow at the
bottom of the dryer’s front panel with laundry,
rugs, etc. Blockage will decrease airflow through
the dryer, thus reducing the efficiency of the dryer.
12
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
510977
Installation
Exhaust System
NOTE: Weather hood should be installed at least
12 inches (30.5 cm) above the ground. Larger
clearances may be necessary for installations where
heavy snowfall can occur.
For best drying results, recommended maximum
length of exhaust system is shown in Table 1.
To prevent backdraft when dryer is not in operation,
outer end of exhaust pipe must have a weather hood
with hinged dampers (obtain locally).
Number of
90° Elbows
Weather Hood Type
Use Only for Short Run Installations
Recommended
4 in.
(10.2 cm)
4 in.
(10.2 cm)
D673I
0
1
2
3
4
2-1/2 in.
(6.35 cm)
D802I
Maximum length of 4 in. (10.2 cm) diameter rigid metal duct.
65 feet (19.8 m)
55 feet (16.8 m)
55 feet (16.8 m)
47 feet (14.3 m)
36 feet (11.0 m)
28 feet (8.5 m)
47 feet (14.3 m)
41 feet (12.5 m)
30 feet (9.1 m)
22 feet (6.7 m)
NOTE: Deduct 6 feet (1.8 m) for each additional elbow.
Table 1
NOTE: The maximum length of a 4 in. (10.2 cm)
diameter flexible metal duct must not exceed
7.87 ft. (2.4 m), as required to meet UL2158, clause
7.3.2.A.
510977
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
13
Installation
Multi-Dryer Installation Exhaust
Requirements
Figure 7 shows a typical example of a multiple dryer
installation. Note how each dryer has its own exhaust
system vented to the central exhaust duct.
2
1
S
TION
RUC
INST )
S,
ING (heat setting
heat)
RAT Type PRES
(no
OPE FabricAL, PERM
FLUFF
1.
2.
3.
4.
5.
6.
SelectNORMATE,
DELIC
Start.
s.
Push
.
Clothe
and
)/Card Door
Door.
Coin(s Close
Start.
- Open
Push
Cycle
Dryer
and
During Door
Dryer Close
When
lete
rt Dryer is Comp Off.
LOAD
Goes
CycleLight
EACH
R
DryingPanel
AFTE
Load
Insert
To
To
To
Start
Stop
Resta
R
FILTE
N
LINT
CLEA
504210
CATE
DELI
S
IN
USE
F )
FLUFHEAT
(NO
PRES
PERM
OR
ECT
SEL
MAL
NOR
RIC
FAB
RT
H TO
STA
PUS
S
TION
RUC
INST )
S,
ING (heat setting
heat)
RAT Type PRES
(no
OPE FabricAL, PERM
FLUFF
1.
2.
3.
4.
5.
6.
SelectNORMATE,
DELIC
Start.
s.
Push
.
Clothe
and
)/Card Door
Door.
Coin(s Close
Start.
- Open
Push
Cycle
Dryer
and
During Door
Dryer Close
When
lete
rt Dryer is Comp Off.
LOAD
Goes
CycleLight
EACH
R
DryingPanel
AFTE
Load
Insert
To
To
To
Start
Stop
Resta
R
FILTE
N
LINT
CLEA
504210
CATE
DELI
S
IN
USE
F )
FLUFHEAT
(NO
PRES
PERM
OR
ECT
MAL
SEL
NOR
RIC
FAB
RT
H
TO
STA
PUS
S
TION
RUC
INST )
S,
ING (heat setting
heat)
RAT Type PRES
(no
OPE FabricAL, PERM
FLUFF
1.
2.
3.
4.
5.
6.
SelectNORMATE,
DELIC
Start.
s.
Push
.
Clothe
and
)/Card Door
Door.
Coin(s Close
Start.
- Open
Push
Cycle
Dryer
and
During Door
Dryer Close
When
lete
rt Dryer is Comp Off.
LOAD
Goes
CycleLight
EACH
R
DryingPanel
AFTE
Load
Insert
To
To
To
Start
Stop
Resta
R
FILTE
N
LINT
CLEA
504210
24" (61 cm)
MINIMUM
CLEARANCE TO
ROOF/GROUND
CATE
DELI
S
USE
OR
ECT
MAL
NOR
IN
F )
FLUFHEAT
(NO
PRES
PERM
SEL
RIC
FAB
H TO
PUS
RT
STA
METERED MODELS
ILLUSTRATED
3
D711I
1
2
58786 Backdraft Damper (Available through
your local authorized parts source)
Clean Out Cover must be provided.
Inspect monthly.
3
Weather Hood or Sweep Elbow
(No cap or screen)
Figure 7
14
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
510977
Installation
1
A
B
C
D
E
F
G
H
I
J
2
K
5
3
AIR
FLOW
4
EXHAUST AIR FLOW
MAXIMUM LENGTH OF DUCT
30 feet (9.1 m)
30°
EXHAUST
OUTLET
24 in. (61 cm)
MINIMUM
CLEARANCE TO
ROOF/GROUND
D686I
HORIZONTAL EXHAUST INSTALLATION
D686I
1
2
NOTE: Where the exhaust duct pierces a
combustible wall or ceiling, the opening must be
sized per local codes.
Wall
3
4
5
2 in. (5 cm) Minimum or Clearance per Local
Codes
No Screen or Cap
Clean Out Cover – Inspect Monthly
Figure 8
WARNING
2
24 in. (61 cm)
MINIMUM
CLEARANCE TO
ROOF/GROUND
To reduce the risk of fire and the
accumulation of combustion gases, DO NOT
exhaust dryer air into a window well, gas
vent, chimney or enclosed, unventilated
area, such as an attic, wall, ceiling, crawl
space under a building or concealed space
of a building.
3
1
W045
CONNECT TO DRYER
4
5
VERTICAL EXHAUST INSTALLATION
D753I
1
2
3
4
5
Roof
No Screen or Cap
Wall
2 in. (5 cm) Minimum
NOTE: Where the exhaust duct pierces a
combustible wall or ceiling, an opening must
be sized as shown or per local codes.
Figure 9
510977
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
15
Installation
Duct Station
Minimum Diameter of
Collector Duct
A
4 inches (10.2 cm)
B
8 inches (20.3 cm)
C
9 inches (22.9 cm)
D
10 inches (25.4 cm)
E
11 inches (27.9 cm)
F
12 inches (30.5 cm)
G
13 inches (32.6 cm)
H
14 inches (35.6 cm)
I
15 inches (38.1 cm)
J
15 inches (38.1 cm)
K
16 inches (40.6 cm)
1. Make certain your dryer is equipped for use with
the type of gas in your laundry room. Dryer is
equipped at the factory for Natural Gas with a
3/8 inch NPT gas connection.
NOTE: The gas service to a gas dryer must
conform with the local codes and ordinances, or in
the absence of local codes and ordinances, with the
latest edition of the National Fuel Gas Code ANSI
Z223.1/NFPA 54 or the CAN/CSA-B149.1 Natural
Gas and Propane Installation Code.
Natural Gas, 1000 Btu/ft3 (37.3 MJ/m3), service must
be supplied at minimum 5.0 inch water column
pressure to maximum 10.5 inch water column
pressure.
A Backdraft Damper, Part No. 58786 (obtain locally),
should be installed in a 4 inch (10.2 cm) diameter
VERTICAL duct system. This will prevent a backdraft
when dryer is not in use, and will keep the exhaust air
in balance within the central exhaust system.
For proper operation at altitudes above 2000 feet
(610 m) the natural gas valve spud orifice size must be
reduced to ensure complete combustion. Refer to
Table 2.
Natural Gas Altitude Adjustments
Altitude
Step 3: (Gas Dryer Only) Connect Gas
Supply Pipe
WARNING
To reduce the risk of gas leaks, fire or
explosion:
• The dryer must be connected to the type
of gas as shown on nameplate located in
the door recess.
• Use a new flexible stainless steel
connector.
• Use pipe joint compound insoluble in L.P.
(Liquefied Petroleum) Gas, or Teflon tape,
on all pipe threads.
• Purge air and sediment from gas supply
line before connecting it to the dryer.
Before tightening the connection, purge
remaining air from gas line to dryer until
odor of gas is detected. This step is
required to prevent gas valve
contamination.
• Do not use an open flame to check for gas
leaks. Use a non-corrosive leak detection
fluid.
• Any disassembly requiring the use of
tools must be performed by a suitably
qualified service person.
Orifice Size
feet
m
#
inches
mm
Part
Number
2,000
610
41
0.0960
2.44
503776
3,000
915
42
0.0935
2.37
503777
5,500
1,680
43
0.0890
2.26
503778
7,000
2,135
44
0.0860
2.18
58719
9,000
2,745
45
0.0820
2.08
503779
10,500
3,200
46
0.0810
2.06
503780
Table 2
2. Remove the shipping cap from the gas
connection at the rear of the dryer. Make sure you
do not damage the pipe threads when removing
the cap.
3. Connect to gas supply pipe.
W316
16
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
510977
Installation
NOTE: When connecting to a gas line, an
equipment shut-off valve must be installed within
6 feet (1.8 m) of the dryer. An 1/8 in. NPT pipe plug
must be installed as shown for checking inlet
pressure. Refer to Figure 10.
1
3
Step 4: (Electric Dryer Only) Connect
Electrical Plug
Dryer requires 120/240 Volt or 120/208 Volt, 60 Hertz,
3 or 4 wire electrical supply. Refer to serial plate for
specific electrical requirements.
4
D233I
D233I
5
503785
58755
503786
NOTE: DO NOT connect the dryer to L.P. Gas
Service without converting the gas valve. Install
L.P. Gas Conversion Kit 458P3, available at extra
cost.
2
2
3
4
Part No.
Table 3
5
1
L.P. Altitude Adjustments
Altitude
Orifice Size
feet
m
No.
inches
mm
3500
1070
54
0.0550
1.40
7500
2290
55
0.0520
1.32
11000
3355
56
0.0465
1.18
New Stainless Steel Flexible Connector –
(Use design CSA certified connector)
Use only if allowed by local codes
1/8 in. NPT Pipe Plug
Equipment Shut Off Valve
Black Iron Pipe
Shorter than 20 ft. (6.1 m) – Use 3/8 in.
(9.5 mm) pipe.
Longer than 20 ft. (6.1 m) – Use 1/2 in.
(12.7 mm) pipe.
3/8 in. NPT Gas Connection
Figure 10
4. Tighten all connections securely. Turn on gas and
check all pipe connections (internal & external)
for gas leaks with a non-corrosive leak detection
fluid.
NOTE: The wiring diagram is located inside the
control hood.
WARNING
To reduce the risk of fire, electric shock,
serious injury or death, all wiring and
grounding MUST conform with the latest
edition of the National Electrical Code,
ANSI/NFPA 70, or the Canadian Electrical
Code, CSA C22.1, and such local
regulations as might apply. It is the
customer’s responsibility to have the wiring
and fuses installed by a qualified electrician
to make sure adequate electrical power is
available to the dryer.
W521
NOTE: The dryer and its appliance main gas valve
must be disconnected from the gas supply piping
system during any pressure testing of that system
at test pressures in excess of 1/2 psi (3.45 kPa).
Refer to Step 9 (Check Heat Source).
L.P. (Liquefied Petroleum) Gas, 2500 Btu/ft.3
(93.1 MJ/m3), service must be supplied at 10 ± 1.5
inch water column pressure.
For proper operation at altitudes above 3500 feet
(1070 m) the L.P. gas valve spud orifice size must be
reduced to ensure complete combustion. Refer to
Table 3.
510977
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
17
Installation
Grounding Information
●
●
18
This dryer must be connected to a grounded
metal, permanent wiring system; or an
equipment-grounding conductor must be run
with the circuit conductors and connected to the
equipment-grounding terminal or lead on the
dryer.
The dryer has its own terminal block that must be
connected to a separate branch, 60 Hertz, single
phase circuit, AC (alternating current) circuit,
fused at 30 Amperes (the circuit must be fused
on both sides of the line). Electrical service for
the dryer should be of maximum rated voltage
(208 or 240 Volt, depending on heating
element) listed on the nameplate. Do not
connect dryer to 110, 115, or 120 Volt circuit.
●
Heating elements are available for field
installation in dryers which are to be connected to
electrical service of different voltage than that
listed on nameplate, such as 208 Volt.
NOTE: Branch circuit wire size requirements to
laundry room outlet are shown in Table 4.
Wire Length
Dryer
Less than
15 ft. (4.5 m)
Longer than
15 ft. (4.5 m)
Listed No. 10 AWG
Copper wire only
Listed No. 8 AWG
Copper wire only
Table 4
●
The power cord connection between wall
receptacle and dryer terminal block IS NOT
supplied with dryer. Type of power cord and
gauge of wire must conform to local codes.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
510977
Installation
IMPORTANT: Use only a new U.L. listed No. 10
(copper wire only) three conductor power supply
cord kit rated 240 Volts (minimum) 30 Amperes
and labeled as suitable for use in a clothes dryer.
1
1
2
3
8
7
2
4
3
5
4
6
THREE-WIRE
D679I
THREE-WIRE CONNECTION
D275I
D679I
2
8
1
1
3
3
7
4
1
4
FOUR-WIRE
9
D006I
1
2
3
4
Typical Receptacle
Power Cord
Strain Relief Nut
Strain Relief
10
11
6
FOUR-WIRE CONNECTION
Figure 11
D680I
D680I
NOTE: Dryer is shown with access cover removed for
illustration purposes only. NEVER operate the dryer
with access cover removed.
1
Ground Wire
2
Ground to Neutral Wire
3
Neutral Terminal
4
“L2” Terminal
5
Center Wire (Neutral)
6
Strain Relief (Not supplied with dryer)
7
Ground Screw
8
“L1” Terminal
9
Black Wire
10
White Wire (Neutral)
11
Red Wire
Figure 12
510977
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
19
Installation
Connecting Power Cord with Three-Wire Plug
NOTE: Four-wire cord is required for mobile
homes or where codes do not permit grounding
through neutral.
NOTE: The power cord is NOT supplied with the
electric dryer. Type of power cord and gauge of wire
must conform to local codes and instructions.
POWER SUPPLY
POWER SUPPLY
1
The method of wiring the dryer is optional and subject
to local code requirements.
2
NOTE: Connect the dryer to the power supply with the
MAXIMUM RATED VOLTAGE listed on the nameplate.
A typical
30-Amp
Three-Wire
Receptacle
NEMA Type
10-30R
3
INTERMEDIATE
FUSE BOX (may
be omitted if
service entrance
box is fused)
4
WALL
RECEPTACLE
5
120 ± 12
V.A.C.
120 ± 12
V.A.C.
INTERMEDIATE
SHUT-OFF BOX
(may or may not
be fused)
6
7
240 ± 12
V.A.C.
NOTE: Use COPPER WIRE only.
Shorter than 15 ft. (4.5 m) – use 10 AWG
Longer than 15 ft. (4.5 m) – use 8 AWG
L1
L2
L1
POWER CORD CONNECTION
L2
DIRECT CONNECTION
D816I
1
3 Wire Grounded Neutral 120/240 Volt, 60 Hertz
AC 1 Phase Service Entrance Switch Box
(Refer to NOTE above)
2
3
30 Ampere Fuses or Circuit Breaker
Neutral Wire
4
5
6
7
Metallic or Non-Metallic Sheathed Cable
(Copper Wire Only)
Power Cord (Not supplied with dryer)
Neutral
Terminal Block in Dryer
Figure 13
1. Disconnect power to dryer.
3. Use a strain relief and insert end of power cord
through power supply hole.
2. Remove access cover from rear of dryer.
D696I
D695I
Figure 14
20
Figure 15
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
510977
Installation
4. Use the three screws from the accessories bag to
attach the power cord wires to the terminal block.
Refer to Figure 16.
1
2
1
3
2
12
V. 0 ±
A 1
.C 2
.
4
12
V. 0 ±
A 1
.C 2
.
240 ± 12
V.A.C.
12
V. 0 ±
A 1
.C 2
.
12
V. 0 ±
A 1
.C 2
.
3
0
V.A.C.
D286I
1
2
3
“L1” Terminal
Neutral Terminal
“L2” Terminal
Figure 16
5. Tighten all screws firmly.
IMPORTANT: Failure to tighten these screws
firmly may result in wire failure at the terminal
block.
DRY2016N
1
2
3
4
Typical Four-Wire Receptacle
Power Cord – Not Supplied with Dryer
Strain Relief Nut
Strain Relief
Figure 17
1. Disconnect power to dryer.
2. Remove access cover from rear of dryer.
6. Secure the strain relief to the power cord, or
wires, where they enter the dryer cabinet.
7. Check the continuity of the ground connection
before plugging the cord into an outlet. Use an
acceptable indicating device connected to the
center grounding pin of the plug and the green
screw on the back of the cabinet.
8. Reinstall access cover and screw.
Connecting Power Cord with Four-Wire Plug
NOTE: Four-wire cord is required for mobile
homes or where codes do not permit grounding
through neutral.
510977
D695I
Figure 18
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
21
Installation
3. Remove ground screw and save for use in Step 5.
Remove wire and use in Step 6.
5. Attach power cord ground (green) wire to rear
bulkhead using ground screw removed in Step 3.
1
1
7
6
5
2
4
D697I
D697I
1
Ground Screw
3
DRY1920N
DRY1920N
Figure 19
4. Use a strain relief and insert end of power cord
through power supply hole.
1
2
3
4
5
6
7
White
“L2” Terminal
Black
Green
Red
Neutral Terminal
“L1” Terminal
Figure 21
6. Use the three screws from the accessories bag to
attach the remaining power cord wires to the
terminal block as follows:
a. Red wire to “L1” terminal.
D696I
Figure 20
b. Black wire to “L2” terminal.
c. White wire to Neutral terminal.
NOTE: When installing the white wire, loop the
free eyelet end of the ground wire (removed in
Step 3) and attach along with the white wire to the
neutral (center) terminal on the terminal block.
7. Tighten all screws firmly.
IMPORTANT: Failure to tighten these screws
firmly may result in wire failure at the terminal
block.
8. Secure the strain relief to the power cord, or
wires, where they enter the dryer cabinet.
9. Check the continuity of the ground connection
before plugging the cord into an outlet. Use an
acceptable indicating device connected to the
center grounding pin of the plug and the green
screw on the back of the cabinet.
10. Reinstall access cover and screw.
22
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
510977
Installation
Step 5: Reverse Door, if Desired
4. Rotate door panel 180 degrees as shown.
The door on this dryer is completely reversible. To
reverse door proceed as follows:
1. Remove four hinge attaching screws.
S
ON
CTI
TRU
INS g)
ING (heat settinS,
heat)
RATc Type PRES
F (no
OPE t Fabri PERM
FLUF
1.
2.
3.
4.
5.
6.
MAL, ,
SelecNORCATE
DELI
Start.
es.
Push
Cloth
rd.
and
Load
Door.
s)/Ca
Door
t Coin( - Close
Start.
- Open
Inser
Push
Dryer
g Cycle and
Start
Durin
Door
Dryer Close
When
Stop
lete
D
rt Dryer is Comp Off.
LOA
H
Goes
Resta
EAC
g Cycle
l Light
R
DryinPane
AFTE
To
To
To
ER
FILT
AN
LINT
CLE
0
50421
D273P
Figure 25
5. Remove door strike from door liner and reinstall
on opposite side.
D661I
D661I
Figure 22
2. Remove all nine screws.
DRY1917N
DRY1917N
Figure 26
6. Insert liner under flange on bottom of door, then
push top of door liner into place.
D272P
Figure 23
3. Pull bottom of door liner out, then pull down,
removing door liner from door panel.
B
A
DRY1918N
DRY1918N
Figure 27
B
7. Reinstall nine screws removed in Step 2.
A
DRY1916N
DRY1916N
Figure 24
DRY1919N
DRY1919N
Figure 28
510977
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
23
Installation
8. Using screwdriver, remove two door plugs, and
reinstall on opposite side of door opening.
INS
Electric Dryer
Connect the dryer to an electrical power source. Refer
to Step 4 for information on connecting power cord.
NS
TIO
TR
Step 7: Plug In the Dryer
UC
g)
ING (heat settin
SS, )
AT
heat
M PRE
(no
ER ic Type
, PER F
ct FabrMAL FLUF
Sele NORICATE,
.
DEL
Start
es.
Push
Cloth
.
and
ard.
Load
Door
(s)/C
.
e Door
Open
t Coin - Clos
Start
er
Inser
Push
Drye
g Cycl and
Start
r Durin e Door
n
Drye
Whe
Clos
rStop
D
Drye Complete
Off.
art
H LOA
e is Goes
Rest
EAC
g Cycll Light
ER
DryinPane
AFT
OP
1.
2.
3.
4.
5.
6.
To
To
To
ER
FILT
AN
CLE
LINT
0
50421
TE
ICA
DEL
M
PER
SS
PRE
IN
USE
FF T)
FLU HEA
(NO
EC
MAL
NOR
TO
R
SEL
RIC
FAB
RT
PU
SH
TO
STA
D385i
Connect to 30 Amp circuit.
D385I
D275I
Figure 29
9. Reinstall four hinge attaching screws, removed in
Step 1.
Figure 32
Gas Dryer
Dryer requires 120 Volt, 60 Hertz electrical supply and
comes equipped with a 3-prong grounding plug. Refer
to serial plate for specific electrical requirements.
NOTE: The wiring diagram is located inside the
control hood.
D606I
Figure 30
Step 6: Wipe Out Inside of Dryer
Before using dryer for the first time, use an all-purpose
cleaner, or a detergent and water solution, and a damp
cloth to remove shipping dust from inside dryer drum.
CTI
ON
S
TRU
INS g)
G
settinS,
TIN (heatPRESheat)
(no
ERA c Type
PERM F
t Fabri
MAL, , FLUF
SelecNORCATE
DELI
Start.
es.
Push
Cloth
rd.
.
and
Door
Load
s)/Ca
Door
Start.
t Coin( - Close
- Open
Inser
Push
Dryer
g Cycle and
Start
Durin
Door
Dryer Close
When
Stop
lete
D
rt Dryer is Comp Off.
LOA
H
Goes
Resta
EAC
g Cycle
l Light
ER
DryinPane
AFT
OP
1.
2.
3.
4.
5.
6.
To
To
To
ER
FILT
AN
CLE
WARNING
D606I
LINT
To reduce the risk of fire, electric shock,
serious injury or death, all wiring and
grounding MUST conform with the latest
edition of the National Electrical Code,
ANSI/NFPA 70, or the Canadian Electrical
Code, CSA C22.1, and such local
regulations as might apply. It is the
customer’s responsibility to have the wiring
and fuses installed by a qualified electrician
to make sure adequate electrical power is
available to the dryer.
W521
0
50421
E
ICAT
DEL
SS
M
IN
USE
FF T)
FLU HEA
(NO
PRE
PER
OR
ECT
MAL
SEL
NOR
RIC
FAB
RT
H
TO
STA
PUS
When plugging in the dryer:
D621I
●
Do not overload circuits.
●
Do not use an adapter.
●
Do not use an extension cord.
●
Do not operate both a washer and gas dryer on
the same circuit. Use separately fused 15 Amp
circuits.
D621I
Figure 31
24
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
510977
Installation
The dryer is designed to be operated on a separate
branch, polarized, three-wire, effectively grounded,
120 Volt, 60 Hertz, AC (alternating current) circuit
protected by a 15 Ampere fuse, equivalent fusetron or
circuit breaker.
The three-prong grounding plug on the power cord
should be plugged directly into a polarized three-slot
effectively grounded receptacle rated 120 Volts AC
(alternating current) 15 Amps. Refer to Figure 33 to
determine correct polarity of the wall receptacle.
WARNING
To reduce the risk of an electric shock or
fire, DO NOT use an extension cord or an
adapter to connect the dryer to the electrical
power source.
W037
M
Grounding Information
The dryer must be grounded. In the event of
malfunction or breakdown, grounding will reduce the
risk of electric shock by providing a path of least
resistance for electric current. The dryer is equipped
with a cord having an equipment-grounding conductor
and a three-prong grounding plug. The three-prong
grounding plug on the power cord should be plugged
directly into a polarized three-slot effectively
grounded receptacle rated 110/120 Volts AC
(alternating current) 15 Amps.
2
3
1
120±12
V.A.C
0 V.A.C
D254I
120±12
V.A.C
4
WARNING
This dryer is equipped with a three-prong
(grounding) plug for your protection against
shock hazard and should be plugged
directly into a properly grounded threeprong receptacle. Do not cut or remove the
grounding prong from this plug.
W036
WARNING
Improper connection of the equipmentgrounding conductor can result in a risk of
electric shock. Check with a qualified
electrician or service person if you are in
doubt as to whether the dryer is properly
grounded.
W038
Do not modify the plug provided with the dryer – if it
will not fit the outlet, have a proper outlet installed by
a qualified electrician.
NOTE: Have a qualified electrician check the
polarity of the wall receptacle. If a voltage reading
is measured other than that illustrated, the
qualified electrician should correct the problem.
5
Plug cord into separately fused 15 Amp circuit.
DRY2
DRY2022N
1
2
3
4
5
L1
Ground
Neutral
Neutral Side
Round Grounding Prong
Figure 33
Step 8: Recheck Steps 1-7
Refer to Installer Checklist on the back cover of this
manual and make sure that dryer is installed correctly.
Step 9: Check Heat Source
Electric Dryers
Close the loading door and start the dryer in a heat
setting (refer to the Operation section). After the dryer
has operated for three minutes, the exhaust air or
exhaust pipe should be warm.
Do not operate other appliances on the same circuit
when this appliance is operating.
510977
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
25
Installation
Gas Dryers
After the dryer has operated for approximately five
minutes, observe burner flame through lower front
panel. Adjust the air shutter to obtain a soft, uniform
blue flame. (A lazy, yellow-tipped flame indicates lack
of air. A harsh, roaring, very blue flame indicates too
much air.) Adjust the air shutter as follows:
IMPORTANT: This operation is to be conducted
by qualified personnel only.
To view the burner flame, remove the lower front
panel of the dryer.
Close the loading door, start the dryer in a heat setting
(refer to the Operation section). The dryer will start,
the igniter will glow red and the main burner will
ignite.
IMPORTANT: If all air is not purged out of gas
line, gas igniter may go off before gas is ignited. If
this happens, after approximately two minutes
igniter will again attempt gas ignition.
1. Loosen the air shutter lockscrew.
2. Turn the air shutter to the left to get a luminous
yellow-tipped flame, then turn it back slowly to
the right to obtain a steady, soft blue flame.
3. After the air shutter is adjusted for proper flame,
tighten the air shutter lockscrew securely.
4. Reinstall the lower front panel.
WARNING
IMPORTANT: If igniter does not light, make sure
gas is turned on.
For personal safety, lower front panel must
be in place during normal operation.
W046
After the dryer has operated for approximately three
minutes, exhaust air or exhaust pipe should be warm.
ELECTRONIC DISPLAY CONTROL, MDC AND NETMASTER
MODELS THROUGH SERIAL NO. 0803, AND
ELECTROMECHANICAL MODELS
ELECTRONIC DISPLAY CONTROL, MDC AND NETMASTER
MODELS STARTING SERIAL NO. 0804
2
2
1
1
6
6
3
3
4
5
4
5
D700I
1
2
3
4
Closed Position
Shut-Off Valve Handle
Air Shutter Lockscrew
Air Shutter
DRY2235N
5
6
1/8 in. (3.1 mm) Pipe Plug
(For checking manifold pressure)
Open Position
Figure 34
26
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
510977
Operation
Operation Instructions for
Electromechanical Dryers
Step 2: Load Laundry
Load clothes loosely into dryer drum. Add fabric
softener sheet if desired.
WARNING
To reduce the risk of fire, electric shock, or
injury to persons, read the IMPORTANT
SAFETY INSTRUCTIONS before operating
this appliance.
OPERATING INSTRUCTIONS
PERM PRESS
NORMAL
1. Select Fabric Type (heat setting)
NORMAL, PERM PRESS,
DELICATE, FLUFF (no heat)
DELICATE
2. Load Clothes.
FLUFF
(NO HEAT)
3. Insert Coin(s)/Card.
IN USE
FABRIC SELECTOR
4. To Start Dryer - Close Door and Push Start.
5. To Stop Dryer During Cycle - Open Door.
6. To Restart Dryer - Close Door and Push Start.
Drying Cycle is Complete When
Panel Light Goes Off.
PUSH TO START
CLEAN LINT FILTER AFTER EACH LOAD
504210
W727
IMPORTANT: Before using dryer for the first time,
use an all-purpose cleaner, or a detergent and
water solution, and a damp cloth to remove
shipping dust from inside of dryer drum.
IMPORTANT: Remove all sharp objects from
laundry to avoid tears and rips to items during
normal machine operation.
D626I
Step 1: Clean Lint Filter
D626I
Figure 36
Clean lint filter before each use.
Step 3: Close Loading Door
Close loading door. Dryer will not operate with the
door open.
S
ON
CTI
TRU
INS g)
ING (heat settinS,
heat)
RATc Type PRES
F (no
OPE t Fabri PERM
FLUF
MAL, ,
SelecNORCATE
DELI
Start.
es.
Push
Cloth
rd.
and
Load
Door.
s)/Ca
Door
t Coin( - Close
Start.
- Open
Inser
Push
Dryer
g Cycle and
Start
Durin
Door
To
4.
Dryer Close
When
Stop
lete
D
To
rt Dryer is Comp Off.
5.
H LOA
Goes
Resta
To
g Cycle
l Light
R EAC
6.
DryinPane
AFTE
1.
2.
3.
ER
FILT
AN
CLE
LINT
0
50421
E
ICAT
DEL
M
PER
SS
PRE
MAL
NOR
IN
USE
FF T)
FLU HEA
(NO
OR
ECT
SEL
RIC
FAB
H TO
PUS
RT
STA
TR
UC
NS
TIO
INS ng)
ING (heat settiSS, )
AT
heat
M PRE
(no
ER ic Type
, PER FF
ct FabrMAL FLU
Sele NORICATE,
t.
DEL
Star
es.
Push
Cloth
r.
ard.
r and
Load
(s)/C
n Doo
t.
e Doo
Ope
Star
rt Coin - Clos
er
Inse
Push
Cycl
t Drye
ng
r and
Star
r Duri e Doo
n
Drye
Whe
Clos
rStop
D
To
Drye Complete
5.
s Off.
art
LOA
H
e is t Goe
Rest
To
EAC
g Cycll Ligh
6.
ER
DryinPane
AFT
OP
1.
2.
3.
4.
To
ER
FILT
AN
LINT
CLE
10
5042
TE
ICA
DEL
M
PER
SS
PRE
MAL
NOR
IC
BR
FA
SH
PU
IN
USE
FF T)
FLU HEA
(NO
R
TO
LEC
SE
TO
RT
STA
D625I
D625I
Figure 35
D712I
D712I
Figure 37
510977
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
27
Operation
Step 4: Set Fabric Selector
Step 5: Start Dryer
Select NORMAL for cottons, PERM PRESS for
permanent press, DELICATE for sensitive items or
FLUFF (NO HEAT) for items that require no heat.
Place coin(s) in slide and carefully push in as far as
possible and then pull slide out as far as possible. After
IN USE light comes on (indicating start of cycle),
press the PUSH-TO-START button.
NOTE: Always follow manufacturer’s care label
instructions.
PERM PRESS
DELICATE
FLUFF
(NO HEAT)
NORMAL
FABRIC SELECTOR
D363I
CPD104B
CPD104B
Figure 39
Figure 38
28
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
510977
Operation
Operation Instructions for
Electronic Display Control Dryers
Step 2: Load Laundry
Load clothes loosely into dryer drum. Add fabric
softener sheet if desired.
WARNING
To reduce the risk of fire, electric shock, or
injury to persons, read the IMPORTANT
SAFETY INSTRUCTIONS before operating
this appliance.
OPERATING INSTRUCTIONS
1. Select Fabric Type (heat setting)
NORMAL, PERM PRESS,
DELICATE, FLUFF (no heat)
2. Load Clothes.
3. Insert Coin(s)/Card.
4. To Start Dryer - Close Door and Push Start.
5. To Stop Dryer During Cycle - Open Door.
HIGH
TEMP
START
LOW
6. To Restart Dryer - Close Door and Push Start.
TEMP
MED
NO
TEMP
HEAT
Drying Cycle is Complete When
Panel Light Goes Off.
CLEAN LINT FILTER AFTER EACH LOAD
505605
W727
IMPORTANT: Before using dryer for the first time,
use an all-purpose cleaner, or a detergent and
water solution, and a damp cloth to remove
shipping dust from inside of dryer drum.
IMPORTANT: Remove all sharp objects from
laundry to avoid tears and rips to items during
normal machine operation.
D628I
D628I
Step 1: Clean Lint Filter
Figure 41
Clean lint filter before each use.
Step 3: Close Loading Door
Close loading door. Dryer will not operate with the
door open.
TR
UC
TIO
NS
INS g)
ING (heat settin
SS, )
AT
heat
M PRE
(no
ER ic Type
, PER FF
ct FabrMAL FLU
Sele NORICATE,
.
DEL
Start
es.
Push
Cloth
.
and
ard.
Load
(s)/C
n Door
.
e Door
Ope
Start
rt Coin - Clos
er
Inse
Push
Drye
g Cycl and
Start
r Durin e Door
To
n
Drye
Whe
Clos
rStop
D
To
Drye Complete
s Off.
art
LOA
H
e is t Goe
Rest
EAC
g Cycll Ligh
ER
DryinPane
AFT
OP
1.
2.
3.
4.
5.
6.
To
ER
FILT
AN
LINT
CLE
7
50561
S
CATE
TEMP
DELI
NS
TIO
UC
LOW
MAL
NORTEMP
T
AR
ST
TR
BLE
TUMHEAT
NO
HIGH
INS ng)
ING (heat settiSS, )
AT
heat
M PRE
(no
ER ic Type
, PER FF
ct FabrMAL FLU
Sele NORICATE,
t.
DEL
Star
es.
Push
Cloth
r.
ard.
r and
Load
(s)/C
n Doo
t.
e Doo
Ope
Star
rt Coin - Clos
er
Inse
Push
Cycl
t Drye
ng
r and
Star
r Duri e Doo
To
n
Drye
Whe
Clos
rStop
D
Drye Complete
s Off.
art
H LOA
e is t Goe
Rest
To
EAC
g Cycll Ligh
ER
DryinPane
AFT
OP
PERMS
TEMP
PRES
1.
MED
2.
3.
4.
5.
6.
To
ER
FILT
AN
LINT
CLE
7
50561
ES
CAT
DELI
TEMP
LOW
MAL
NORTEMP
ST
AR
T
BLE
TUMHEAT
NO
HIGH
M
PERSS
PRETEMP
MED
D627I
D794I
D627I
D794I
Figure 40
Figure 42
510977
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
29
Operation
Step 4: Set Fabric Selector
To Insert Card
Select HIGH TEMP, MED TEMP, LOW TEMP
or NO HEAT by pushing touchpad.
Insert card into opening. Follow directions on display.
DO NOT REMOVE THE CARD UNTIL DISPLAY
READS “Remove Card”.
NOTE: Always follow manufacturer’s care label
instructions.
HIGH
TEMP
START
MED
TEMP
LOW
TEMP
NO
HEAT
M330I
M330I
D452I
Figure 45
D452I
If Additional Time Feature is turned on, additional
dryer time may be purchased at cycle start or while
dryer is running.
Figure 43
Step 5: Insert Coin(s) or Card
To Insert Money
Insert coin(s) in coin slot. Check pricing as seen on
digital display.
Remove knits when slightly damp because overdrying
may cause shrinkage. Do not tumble dry knit woolens.
Step 6: Start Dryer
To start dryer, push START pad.
To stop dryer at any time, open the door. To restart the
dryer, close door and push START pad.
Cycle is completed when time remaining reaches
00 minutes.
HIGH
TEMP
MED
TEMP
START
LOW
TEMP
NO
HEAT
W387I
Figure 44
D451I
D451I
Figure 46
30
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
510977
Operation
Indicator Lights
DOOR OPEN
INSERT COINS
DOOR OPEN is lit and flashes at one-second intervals
whenever the dryer door is open.
INSERT COINS is lit to prompt the user to insert coins
or card to satisfy the vend price for the chosen cycle.
When INSERT COINS is lit, the three digits and
decimal point will display the vend price remaining to
be satisfied.
COOL DOWN
COOL DOWN is lit whenever the COOL DOWN
portion of a heated cycle is active. It is also lit when
the NO HEAT cycle is in operation.
PUSH START
PRICE
PUSH START is lit whenever the dryer is not in a
cycle, the full vend price has been satisfied and the
dryer door is closed. When the START pad is pressed,
the cycle will begin or resume. The PUSH START
status word flashes at one-second intervals when
activated.
PRICE is lit to indicate that the value displayed is the
vend pricing remaining to be satisfied. Once the vend
price is satisfied, the word PRICE will go off.
DRYING
DRYING is lit to indicate that one of the heated cycles
(HIGH TEMP, MED TEMP, LOW TEMP) is currently
in operation. The status word DRYING goes off at the
end of a heated cycle or when the COOL DOWN cycle
begins.
510977
TIME REMAINING
TIME REMAINING is lit to indicate that the time
displayed by two digits and the colon is the time
remaining (in minutes) in the active cycle. The colon
flashes at one-second intervals and time continually
counts down in an active cycle.
Should dryer stop before cycle is completed, the motor
overload protector may have cycled. Refer to
Maintenance section.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
31
Operation
Operation Instructions for
MDC Dryers
Step 2: Load Laundry
Load clothes loosely into dryer drum. Add fabric
softener sheet if desired.
WARNING
To reduce the risk of fire, electric shock, or
injury to persons, read the IMPORTANT
SAFETY INSTRUCTIONS before operating
this appliance.
OPERATING INSTRUCTIONS
1. Select Fabric Type (heat setting)
NORMAL, PERM PRESS,
DELICATE, FLUFF (no heat)
2. Load Clothes.
3. Insert Coin(s)/Card.
4. To Start Dryer - Close Door and Push Start.
5. To Stop Dryer During Cycle - Open Door.
6. To Restart Dryer - Close Door and Push Start.
Drying Cycle is Complete When
Panel Light Goes Off.
CLEAN LINT FILTER AFTER EACH LOAD
W727
IMPORTANT: Before using dryer for the first time,
use an all-purpose cleaner, or a detergent and
water solution, and a damp cloth to remove
shipping dust from inside of dryer drum.
IMPORTANT: Remove all sharp objects from
laundry to avoid tears and rips to items during
normal machine operation.
D795I
D795I
Step 1: Clean Lint Filter
Figure 48
Clean lint filter before each use.
Step 3: Close Loading Door
Close loading door. Dryer will not operate with the
door open.
TR
UC
TIO
NS
INS g)
ING (heat settin
SS, )
AT
heat
M PRE
(no
ER ic Type
, PER FF
ct FabrMAL FLU
Sele NORICATE,
.
DEL
Start
es.
Push
Cloth
.
and
ard.
Load
(s)/C
n Door
.
e Door
Ope
Start
rt Coin - Clos
er
Inse
Push
Drye
g Cycl and
Start
r Durin e Door
n
Drye
Whe
Clos
rStop
D
To
Drye Complete
5.
s Off.
art
LOA
H
e is t Goe
Rest
To
EAC
g Cycll Ligh
6.
ER
DryinPane
AFT
OP
1.
2.
3.
4.
To
ER
FILT
AN
LINT
CLE
NS
TIO
UC
TR
INS ng)
ING t settiSS, t)
AT e (hea
PRE hea
Typ M (no
ER
FF
OP Fabric , PER
FLU
1.
2.
3.
4.
5.
6.
ct MAL
Sele NORICATE,
t.
DEL
h Star
hes.
Pus
r.
ard.
d Clot
r and
Loa
(s)/C
n Doo
t.
e Doo
Ope
rt Coin - Clos
h Star
le r
Inse
Pus
Cyc
t Drye
ng
r and
Star
r Duri e Doo
To
n
Drye
Whe
Clos
rStop
D
To
Drye Complete
s Off.
LOA
tart
H
le is t Goe
Res
Cyc
To
EAC
ng el Ligh
ER
Dryi Pan
AFT
AN
CLE
TER
T FIL
LIN
D796I
D796I
D793I
Figure 47
D793I
Figure 49
32
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
510977
Operation
Step 4: Set Fabric Selector
To Insert Card
Select HIGH TEMP, MED TEMP, LOW TEMP or
DELICATES by pushing touchpad.
Insert card into opening.
NOTE: Always follow manufacturer’s care label
instructions.
DRY1926N
DRY1926N
DRY1927N
Figure 50
Figure 52
Step 5: Insert Coin(s) or Card
If Additional Time Feature is turned on, additional
dryer time may be purchased at cycle start or while
dryer is running.
To Insert Money
Insert coin(s) in coin slot. Check pricing as seen on
digital display.
Remove knits when slightly damp because overdrying
may cause shrinkage. Do not tumble dry knit woolens.
Step 6: Start Dryer
To start dryer, push START pad.
To stop dryer at any time, open the door. To restart the
dryer, close door and push START pad.
Cycle is completed when time remaining reaches
00 minutes.
W387I
Figure 51
DRY19
DRY1928N
Figure 53
510977
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
33
Operation
Indicator Lights
START
START is lit whenever the dryer is not in a cycle, the
full vend price has been satisfied and the dryer door is
closed. When the START pad is pressed, the cycle will
begin or resume.
DRYING
DRYING is lit to indicate that one of the heated cycles
(HIGH TEMP, MED TEMP, LOW TEMP or
DELICATES) is currently in operation. DRYING will
turn off at the end of a heated cycle or when the COOL
DOWN cycle begins.
COOL DOWN
COOL DOWN is lit whenever the COOL DOWN
portion of a heated cycle is active. It is also lit when no
heat is programmed for a cycle in operation.
34
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
510977
Operation
Operation Instructions for
NetMaster Dryers
Step 2: Load Laundry
Load clothes loosely into dryer drum. Add fabric
softener sheet if desired.
WARNING
To reduce the risk of fire, electric shock, or
injury to persons, read the IMPORTANT
SAFETY INSTRUCTIONS before operating
this appliance.
OPERATING INSTRUCTIONS
1. Select Fabric Type (heat setting)
NORMAL, PERM PRESS,
DELICATE, FLUFF (no heat)
2. Load Clothes.
3. Insert Coin(s)/Card.
4. To Start Dryer - Close Door and Push Start.
5. To Stop Dryer During Cycle - Open Door.
6. To Restart Dryer - Close Door and Push Start.
Drying Cycle is Complete When
Panel Light Goes Off.
CLEAN LINT FILTER AFTER EACH LOAD
W727
IMPORTANT: Before using dryer for the first time,
use an all-purpose cleaner, or a detergent and
water solution, and a damp cloth to remove
shipping dust from inside of dryer drum.
IMPORTANT: Remove all sharp objects from
laundry to avoid tears and rips to items during
normal machine operation.
D795I
D795I
Step 1: Clean Lint Filter
Figure 55
Clean lint filter before each use.
Step 3: Close Loading Door
Close loading door. Dryer will not operate with the
door open.
INS
TR
UC
TIO
NS
g)
ING (heat settin
SS, )
AT
heat
M PRE
(no
ER ic Type
, PER FF
ct FabrMAL FLU
Sele NORICATE,
.
DEL
Start
es.
Push
Cloth
.
and
ard.
Load
(s)/C
n Door
.
e Door
Ope
Start
rt Coin - Clos
er
Inse
Push
Drye
g Cycl and
Start
r Durin e Door
To
n
Drye
Whe
Clos
rStop
D
To
Drye Complete
5.
s Off.
art
LOA
H
e is t Goe
Rest
To
EAC
g Cycll Ligh
6.
ER
DryinPane
AFT
OP
1.
2.
3.
4.
ER
FILT
AN
LINT
CLE
NS
TIO
UC
TR
INS ng)
ING t settiSS, t)
AT e (hea
PRE hea
Typ M (no
ER
FF
OP Fabric , PER
FLU
1.
2.
3.
4.
5.
6.
ct MAL
Sele NORICATE,
t.
DEL
h Star
hes.
Pus
r.
ard.
d Clot
r and
Loa
(s)/C
n Doo
t.
e Doo
Ope
rt Coin - Clos
h Star
le r
Inse
Pus
Cyc
t Drye
ng
r and
Star
r Duri e Doo
To
n
Drye
Whe
Clos
rStop
D
To
Drye Complete
s Off.
LOA
tart
H
le is t Goe
Res
Cyc
To
EAC
ng el Ligh
ER
Dryi Pan
AFT
AN
CLE
TER
T FIL
LIN
D796I
D796I
D793I
Figure 54
D793I
Figure 56
510977
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
35
Operation
Step 4: Set Fabric Selector
To Insert Card
Select HIGH TEMP, MED TEMP, LOW TEMP or
NO HEAT by pushing touchpad.
Insert card into opening. DO NOT REMOVE THE
CARD UNTIL THE REMOVE CARD LED IS LIT.
NOTE: Always follow manufacturer’s care label
instructions.
D777I
M343I
M343I
D777I
Figure 59
Figure 57
If Additional Time Feature is turned on, additional
dryer time may be purchased at cycle start or while
dryer is running.
Step 5: Insert Coin(s) or Card
To Insert Money
Insert coin(s) in coin slot. Check pricing as seen on
digital display.
Remove knits when slightly damp because overdrying
may cause shrinkage. Do not tumble dry knit woolens.
Step 6: Start Dryer
To start dryer, push START pad.
To stop dryer at any time, open the door. To restart the
dryer, close door and push START pad.
Cycle is completed when time remaining reaches
00 minutes.
W387I
Figure 58
D778I
Figure 60
36
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
510977
Operation
Indicator Lights
COOL DOWN
INSERT COINS/CARD
COOL DOWN is lit whenever the COOL DOWN
portion of a heated cycle is active. It is also lit when
the NO HEAT cycle is in operation.
INSERT COINS/CARD is lit to prompt the user to
insert coins or a card to satisfy the vend price. When
INSERT COINS/CARD is lit, the three digits and
decimal point will display the vend price remaining to
be satisfied.
START
START is lit whenever the dryer is not in a cycle, the
full vend price has been satisfied and the dryer door is
closed. When the START pad is pressed, the cycle will
begin or resume.
DRYING
DRYING is lit to indicate that one of the heated cycles
(HIGH TEMP, MED TEMP, or LOW TEMP) is
currently in operation. DRYING will turn off at the end
of a heated cycle or when the COOL DOWN cycle
begins.
510977
ADD TIME (Card Models Only)
ADD TIME flashes when a card is inserted while a
cycle is running or when a card is left in the reader for
at least five seconds after a cycle has started.
REMOVE CARD (Card Models Only)
REMOVE CARD flashes when a card is inserted or left
in the reader after a transaction is complete. It will also
flash alternately with ADD TIME when a card is
inserted while a cycle is running or when a card is left
in the reader.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
37
Maintenance
Lubrication
Exhaust System
All moving parts are sealed in a permanent supply of
lubricant or are equipped with oilless bearings.
Additional lubrication will not be necessary.
WARNING
To reduce the risk of electric shock,
disconnect the electrical service to the
dryer before cleaning.
Care of Your Dryer
WARNING
W043
To reduce the risk of an electric shock,
serious injury or death, disconnect the
electrical service to the dryer before
cleaning the interior.
W132
Dryer Interior
Wipe the surfaces using a soft cloth and household
cleaner or a non-abrasive paste of powdered laundry
detergent and hot water, followed by a short heat cycle
with a load of rags.
To remove crayon or ball point ink off the dryer drum,
put the heat on high and use old rags in the dryer to
absorb the crayon or ink. If unsuccessful, contact the
appliance dealer. DO NOT use any chemicals in the
dryer.
IMPORTANT: The use of chlorine bleach for
removing any discolorations should be avoided
because bleach could damage the finish.
Cabinet
Wipe the dryer cabinet as needed. If detergent, bleach
or other washing products have been spilled on the
dryer, wipe immediately. Some products will cause
permanent damage if spilled on the cabinet.
Control Panel
The exhaust duct should be inspected after one year of
use and cleaned if necessary by a qualified service
person to remove any lint build-up. Inspect and clean
exhaust duct every one to two years as required
thereafter.
The weather hood should be checked frequently to
make sure the dampers move freely, dampers are not
pushed in and that nothing has been set against them.
Keep dryer area clear and free from combustible
materials, gasoline and other flammable vapors and
liquids.
Do not obstruct the flow of combustion and ventilation
air.
NOTE: Verify proper operation after servicing.
Lint Filter
CLEAN THE LINT FILTER BEFORE DRYING
EACH LOAD. (Refer to Figure 61 for lint filter
location.) Cleaning the lint filter is important because
a layer or pad of lint on the filter will block the flow of
air through the dryer, thus reducing the efficiency of
the dryer. The clothes will take longer to dry and
energy will be wasted.
The lint filter may be washed if needed. Annually
remove lint filter and screw to vacuum the duct under
it.
Use only a damp or sudsy cloth for cleaning the
control panel. Some spray pretreat products may harm
the finish on the control panel.
S
TION
RUC
INST
)
S,
ING (heat setting
heat)
RAT Type PRES
(no
PERM
FabricAL, FLUFF
SelectNORMATE,
DELIC
OPE
1.
2.
3.
4.
5.
6.
Start.
s.
Push
.
Clothe
and
)/Card Door
Door.
Coin(s Close
Start.
- Open
Push
Cycle
Dryer
and
During Door
Dryer Close
When
lete
t Dryer Comp Off.
LOAD
is Goes
CycleLight
EACH
R
DryingPanel
AFTE
Load
Insert
To
To
To
Start
Stop
Restar
R
FILTE
N
LINT
CLEA
504210
ATE
DELIC
S
PRES
IN
USE
F )
FLUFHEAT
(NO
PERM
OR
AL
ECT
SEL
NORM
RIC
FAB
RT
NOTE: The wiring diagram is located inside the
control panel.
H TO
STA
PUS
1
WARNING
Label all wires prior to disconnection
when servicing controls. Wiring errors
can cause improper and dangerous
operation.
D625I
D625I
1
Lint Filter
W049
Figure 61
38
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
510977
Maintenance
Motor Overload Protector
The dryer’s motor overload protector stops the motor
automatically in the event of an overload. After
cooling, the overload protector will reset itself. Dryer
can be restarted by pressing the PUSH-TO-START
button or START pad. If overload protector cycles
again, remove the dryer from use and call the service
person to correct the problem.
510977
For Energy Conservation
●
Make sure the lint filter is always clean.
●
Do not overload dryer.
●
Do not overdry clothes.
●
Remove items to be ironed while still damp.
●
Large loads of similar fabrics dry the most
efficiently. However, dry permanent press in
smaller loads to prevent wrinkling.
●
Use the correct temperature FABRIC
SELECTOR setting for the type of fabric being
dried.
●
Locate your dryer so the exhaust duct is as short
and straight as possible.
●
Do not open the door during the drying cycle.
●
Plan to do your laundry on low humidity days;
your clothes will dry faster.
●
Should you plan to dry several loads, do them
one after another, then you do not have to reheat
the dryer unit’s interior parts each time.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39
Troubleshooting
Try these troubleshooting tips before making a service call. They may save you time and money.
Dryer Symptom
Possible Cause/Solution
•
•
•
•
Dryer won’t start
•
•
•
•
•
•
•
Dryer won’t heat
•
•
•
•
Dryer doesn’t dry clothes
satisfactorily
•
•
•
•
•
•
Dryer is noisy
•
•
Nonmetered models - Turn timer knob further into cycle.
Metered models - Insert coin(s) or card.
Metered models - Activate timer. Push coin slide all the way in.
For dryers equipped with a power cord, make sure the power cord is plugged all
the way into the electrical outlet.
Make sure loading door is closed.
Press PUSH-TO-START button or START pad.
Make sure the laundry room fuse(s) isn’t blown or loose, or circuit breakers
aren’t open. The dryer itself does not have an electrical fuse. An electric dryer
has an electrical circuit with two fuses.
Check if motor overload protector has cycled. Wait 10 minutes and try again.
Nonmetered models - Turn timer knob further into cycle.
Metered models - Activate timer. Push coin slide all the way in.
Make sure the laundry room fuse(s) isn’t blown or loose, or circuit breakers
aren’t open. The dryer itself does not have an electrical fuse. An electric dryer
has an electrical circuit with two fuses.
Make sure controls are in a HEAT setting.
Gas dryer only – Make sure equipment and main gas line valve is turned on.
Check exhaust duct to outside to see if it is kinked, blocked or needs cleaning.
Check weather hood to make sure flapper moves freely, has not been pushed in
or has not been blocked.
Check exhaust duct to outside to see if it is kinked, blocked or needs cleaning.
Check weather hood to make sure flapper moves freely, has not been pushed in
or has not been blocked.
Clean the lint filter.
Make sure the load isn’t too small. Small loads may not tumble properly or dry
evenly.
Check load being dried. Heavy items dried with lightweight items will not dry as
quickly as the rest of the load.
Check dryer for foreign objects (nails, coins, bobby pins, metal, plastic toys,
etc.). Remove items from dryer.
Make sure dryer is level. Uneven leveling can cause vibration.
Normal operating sounds include the tick of timer advancing, heat source going
on and off, and humming of air moving through the dryer and exhaust system.
Clothes are too wrinkled
•
•
Check heat setting. Overdrying can cause wrinkling.
Check load size. Large loads may not tumble properly and may cause wrinkling.
Clothes have odor
•
Check room for odors before drying clothes. Any odor (fried foods, paint,
varnish, cleaners, burning wood, etc.) will transfer to clothing as the dryer draws
air from the room. Ventilate room before drying clothes.
40
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
510977
Contact Information
If service is required, contact the nearest Factory
Authorized Service Center.
WARNING
If you are unable to locate an authorized service center
or are unsatisfied with the service performed on your
dryer, contact:
Alliance Laundry Systems
Shepard Street
P. O. Box 990
Ripon, WI 54971-0990
U.S.A.
www. comlaundry. com
Phone: (920) 748-3121
To reduce the risk of serious injury or
death, DO NOT repair or replace any part
of the dryer or attempt any servicing
unless specifically recommended in the
user-maintenance instructions or in
published user-repair instructions that
you understand and have the skills to
carry out.
W133
Date Purchased___________________________
Model Number____________________________
Serial Number____________________________
When calling or writing about your dryer, PLEASE
GIVE THE MODEL AND SERIAL NUMBERS. The
model and serial numbers are located on the
nameplate. The nameplate will be in the location
shown in the illustration below. Please include a copy
of your bill of sale and any service receipts you have.
If replacement parts are required, contact the source
from which you purchased your dryer or contact us at
(920) 748-3950 for the name and address of the
nearest authorized parts distributor.
1
D063K
1
Nameplate
Figure 62
510977
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
41
Installer Checklist
Fast Track for Installing the Dryer
(Refer to the manual for more detailed information)
1
6
• Position and Level
the Dryer.
• Wipe Out Inside
of Dryer.
setting)
(heatPRESS,
heat)
Type
(no
PERM
Fabric FLUFF
,
1.SelectNORMAL,
DELICATE
Start.
Push
Clothes. rd.
and
Door.
Door
Coin(s)/CaClose
Start.
- Open
Push
When
3.Insert Dryer
Cycle
and
Start
During Door
4.To
is Complete
Off.
Dryer Close
CycleGoes
Stop
Dryer DryingLight
5.To
Restart
Panel
6.To
2.Load
504210
TE
DELICA
PRESS
PERM
HEAT)
FLUFF
(NO
IN
USE
TOR
C SELEC
L
NORMA
FABRI
TO
START
PUSH
LEVEL
D255I
D255I
D256I
CHECK
2
D662I
D662I
CHECK
D259I
7
• Connect Dryer Exhaust System.
• Plug In the Dryer.
Gas
Electric
D275I
D740I
CHECK
3
GAS ONLY
• Connect Gas
Supply Pipe.
• Check for Gas
Leaks.
8
D258I
ELECTRIC ONLY
• Connect
Electrical Cord.
D699I
W315IE0A
• Reverse Door,
if Desired.
S
TION
RUC
INST
ING (heat setting),
heat)
RAT Type PRESS
(no
OPE FabricAL, PERM
FLUFF
1.
2.
3.
4.
5.
6.
SelectNORM TE,
DELICA
Start.
.
Push
Clothes
and
/Card.
Load
Door.
Door
Coin(s) Close
Start.
- Open
Insert
Push
Cycle
Dryer
and
Start
During Door
To
Dryer Close
te When
Stop
To
Dryer CompleOff.
LOAD
is Goes
Restart
CycleLight
EACH
DryingPanel
AFTER
To
R
FILTE
N LINT
CLEA
504210
D661I
CHECK
9
• Check Heat Source.
CHECK
CHECK
5
• Recheck Steps 1-7.
CHECK
CHECK
4
CHECK
D740I
W661I
D254I
D254I
Download PDF
Similar pages