Network Video Recorder User'

NVR-ELE4ME-WS
PTZ
Control
1
yr
Motion
Activated
Recording
Warranty
View From
Anywhere
1080p
Resolution
Table of Contents
1
Features and Specifications
1.1
Overview
Features
1.2
1.3
Specifications
2
Front Panel and Rear Panel
2.1
Front Panel
2.2
Rear Panel
2.3
Alarm Connection
2.3.1
Alarm Port
2.3.2
Alarm input port
2.3.3
Alarm input and output port
2.3.4
Alarm relay specifications
2.4
Bidirectional talk
2.4.1
Device-end to PC-end
2.4.2
PC-end to the device-end
2.5
Mouse Operation
2.6
Remote Control
3 Device Installation
3.1
Check Unpacked NVR
3.2
About Front Panel and Rear Panel
3.3
HDD Installation
3.4
3.5
4
CD-ROM Installation
Connection Sample
Local Basic Operation
4.1
Getting Started
4.1.1
Boot up and Shut down
4.1.2
Device Initialization
4.1.3
Reset Password
4.1.4
Startup Wizard
4.2
Camera
4.2.1
Connection
4.2.2
Remote Device Initialization
4.2.3
Short-Cut Menu to Add Camera
4.2.4
Image
4.2.5
Encode
4.2.6
Channel Name
4.2.7
Remote Upgrade
4.2.8
Remote Device Info
4.3
Preview
4.3.1
Preview
4.3.2
Navigation bar
Preview Control Interface
4.3.3
4.3.4
Right Click Menu
4.3.5
Edit View (Sequence)
4.3.6
Preview Display Effect Setup
Fisheye (Optional)
4.3.7
4.4
PTZ
4.4.1
PTZ Settings
4.4.2
PTZ Control
4.5
Record File
Playback and Search
4.6
4.6.1
Instant Playback
4.6.2
Search Interface
4.6.3
Smart Search Playback
4.6.4
Mark Playback
Playback Image
4.6.5
4.6.6
Splice Playback
Smart Playback
4.6.7
4.6.8
File List
Other Aux Functions
4.6.9
4.7
Event Manager
Video Detect
4.7.1
4.7.2
Smart Plan
4.7.3
IVS (Optional)
IVS (Behavior Analytics) (Optional)
4.7.4
4.7.5
Face Detect (Optional )
People Counting (Optional)
4.7.6
4.7.7
Heat Map
4.7.8
Plate Recognition
Audio Detect (Optional)
4.7.9
4.7.10 Alarm Settings
4.7.11 Abnormality
4.7.12 Alarm output
4.8
Network
Network Settings
4.8.1
4.8.2
Network Test
4.9
HDD Setup
4.9.1
Format
4.9.2
HDD Information
4.9.3
Advanced
4.9.4
HDD Detect
4.9.5
RAID Manager
4.10 Device Maintenance and Manager
4.10.1 Account
4.10.2 System Info
4.10.3 Voice
5
4.10.4 RS232
4.10.5 POS
4.10.6 Broadcast
4.10.7 Auto Maintain
4.10.8 Backup
4.10.9 Default
4.10.10
Update
4.11 Logout /Shutdown/Restart
5 Web Operation
5.1
General Introduction
Preparation
5.1.1
5.2
Device Initialization
5.2.1
Log in
5.3
Reset Password
5.4
LAN Mode
Real-time Monitor
5.5
5.6
PTZ
Image/Alarm-out
5.7
5.7.1
Image
Alarm output
5.7.2
5.8
Zero-channel Encode
WAN Login
5.9
5.10 Setup
5.10.1 Camera
5.10.2 Network
5.10.3 Event
5.10.4 Storage
5.10.5 Setting
5.11 Information
5.11.1 Version
5.11.2 Log
5.11.3 Online User
5.11.4 People Counting
5.11.5 Heat Map
5.11.6 HDD
5.12 Playback
5.12.1 Search Record
5.12.2 File List
5.12.3 Playback
5.12.4 Download
5.12.5 Load more
5.13 Smart Playback
5.13.1 IVS (Behavior Analytics)
5.13.2 Plate recognition
5.13.3 Human Face
5.14 Alarm
6
6
7
8
9
5.15 Log out
5.16 Un-install Web Control
Glossary
FAQ
Appendix A HDD Capacity Calculation
Appendix B Compatible Network Camera List
7
Copyrights


Any or full contents of the user’s manual cannot be copied, transmitted, distributed, partially or wholly,
by any means, without the prior written notice of us.
We or the third party may reserve the right of the product described in this user’s manual. Without the
prior written approval of the corresponding party, any person cannot (including but not limited to)
copy, distribute, amend, reverse compile, disassemble, engineering, rent, reverse engineer, reverse
compile or disassemble the software.
Trademark
 The trademarks and registered trademarks mentioned are the properties of their respective owners.
Legal Disclaimer
EXCEPT AS PROVIDED HEREIN, THE NETWORK VIDEO RECORDER (HEREIN AFTER
“NVR”,”PRODUCT”,”DEVICE”,”EQUIPMENT”,’SYSTEM’) IS PROVIDED “AS IS”, WITH ALL FAULTS
AND ERRORS, AND WE MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING (BUT NOT
LIMITED TO) MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR
PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL WE, ITS DIRECTORS,
OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE FOR ANY SPECIAL, CONSEQUENTIAL,
INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING (BUT NOT LIMITED TO) DAMAGES FOR LOSS
OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN
CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF WE HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Legal Considerations
Video and audio surveillance can be regulated by laws that vary from country to country. Check the laws
in your local region before using this product for surveillance purposes.
Standards Approvals
For our Wi-Fi series product, please refer to the following important notices.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the
8
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
RF exposure warning
This equipment must be installed and operated in accordance with provided instructions and the
antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm
from all persons and must not be co-located or operating in conjunction with any other antenna or
transmitter. End-users and installers must be provided with antenna installation instructions and
transmitter operating conditions for satisfying RF exposure compliance.
IEEE 802.11b, 802.11g or 802.11n (20MHz) operation of this product in the U.S.A. is firmware-limited to
channels 1 through 11. IEEE 802.11n (40MHz) operation of this product in the U.S.A. is firmware-limited
to channels 3 through 9.
Safety Instruction
Icon
Note
DANGER
Indicates a hazard with a high level of risk, which if not avoided, will
result in death or serious injury.
WARNING
Indicates a potentially hazardous situation, which if not avoided,
could result in device damage, data loss, performance degradation,
or unexpected results.
Indicates it is the static sensitive device.
Anti-static
Eletric shock
Indicates presence of dangerous high voltage. There is a risk of
electric shock to persons.
risk
High
power
Indicates presence of high power laser radiation.
laser radiation risk
Tips
It is intended to help you to fix a problem or save your time.
Note
Provides additional information to emphasize or supplement
important points of the main text.
9
Welcome
Thank you for purchasing our network video recorder!
This user’s manual is designed to be a reference tool for your system.
Please open the accessory bag to check. Contact your local retailer ASAP if something is missing or
damaged in the bag.
Important Safeguards and Warnings
1.Electrical safety





All installation and operation here should conform to your local electrical safety codes.
An apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a
protective earthing connection.
Use a power supply which meets the requirements for SELV (Safety Extra Low Voltage) and
complies with Limited Power Source according to IEC 60950-1. Refer to the device label for detailed
information.
The product must be grounded to reduce the risk of electric shock.
We assume no liability or responsibility for all the fires or electric shock caused by improper handling
or installation.
2.Transportation security

Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3.Installation



Keep upwards. Handle with care.
Do not apply power to the NVR before completing installation.
Do not place objects on the NVR.
4.Qualified engineers needed


All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5.Environment





The NVR should be installed in a cool, dry place away from direct sunlight, inflammable, explosive
substances and etc.
This series product shall be transported, storage and used in the specified environments.
Environment which needs to comply with the following conditions:
The function of the ITE being investigated to IEC 60950-1 is considered not likely to require
connection to an Ethernet network with outside plant routing, including campus environment.
The installation instructions clearly state that the ITE is to be connected only to PoE networks without
routing to the outside plant.
6. Accessories
 Be sure to use all the accessories recommended by manufacturer.
10


Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
7. Lithium battery
 Improper battery use may result in fire, explosion, or personal injury!
 When replace the battery, please make sure you are using the same model!
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
11
1 Features and Specifications
1.1 Overview
This series NVR is a high performance network video recorder. This series product support local preview,
multiple-window display, recorded file local storage, remote control and mouse shortcut menu operation,
and remote management and control function.
This series product supports center storage, front-end storage and client-end storage. The monitor zone
in the front-end can be set in anywhere. Working with other front-end devices such as IPC, NVS, this
series product can establish a strong surveillance network via the CMS. In the network system, there is
only one network cable from the monitor center to the monitor zone in the whole network. There is no
audio/video cable from the monitor center to the monitor zone. The whole project is featuring of simple
connection, low-cost, low maintenance work.
This series NVR can be widely used in many areas such as public security, water conservancy,
transportation and education.
1.2 Features

Real-time
Surveillance



Playback


User
Management
Storage
Alarm


VGA, HDMI port. Connect to monitor to realize real-time surveillance.
Some series support TV/VGA/HDMI output at the same time.
Short-cut menu when preview.
Support popular PTZ decoder control protocols. Support preset, tour
and pattern.
Support each channel real-time record independently, and at the same
time it can support search, forward play, network monitor, record search,
download and etc.
Support various playback modes: slow play, fast play, backward play
and frame by frame play.
Support time title overlay so that you can view event accurate occurred
time
Support specified zone enlargement.
Each group has different management powers that can be edited freely.
Every user belongs to an exclusive group.

Via corresponding setup (such as alarm setup and schedule setup), you
can backup related audio/video data in the network video recorder.

Support Web record and record local video and storage the file in the
client end.

Respond to external alarm simultaneously (within 200MS), based on
user’s pre-defined relay setup, system can process the alarm input
correctly and prompt user by screen and voice (support pre-recorded
audio).

Support central alarm server setup, so that alarm information can
remotely notify user automatically. Alarm input can be derived from
various connected peripheral devices.
Alert you via email/sms.

12
Network
Monitor

Through network, sending audio/video data compressed by IPC or NVS
to client-ends, then the data will be decompressed and display.


Support max 128 connections at the same time.
Transmit audio/video data by HTTP, TCP, UDP, MULTICAST,
RTP/RTCP and etc.


Transmit some alarm data or alarm info by SNMP.
Support WEB access in WAN/LAN.

Adopt the video compression and digital process to show several
windows in one monitor. Support 1/4/8/9/16/ 25/36-window display when
preview and 1/4/9/16-window display when playback.
Support normal/motion detect/alarm record function. Save the recorded
files in the HDD, USB device, client-end PC, or network storage server.
You can search or playback the saved files at the local-end or via the
Web/USB device.
Support network backup, USB2.0 record backup function, the recorded
files can be saved in network storage server, peripheral USB2.0
device, burner and etc.
Supervise NVR configuration and control power via Ethernet.
Support management via WEB.
Support peripheral equipment management such as protocol setup and
port connection.
Support transparent data transmission such as RS232 (RS-422), RS485
(RS-485).
Support switch between NTSC and PAL.
Support real-time system resources information and running statistics
display.
Support log file.
Local GUI output. Shortcut menu operation via mouse.
IR control function (For some series product only.). Shortcut menu
operation via remote control.
Support IPC or NVS remote video preview and control.
Window Split

Record

Backup
Network
Management
Peripheral
Equipment
Management






Auxiliary




13
1.3 Specifications
Technical Specification
Audio and Video
System
IP Camera Input
4 Channel
N/A
Main Processor
Dual-core embedded processor
Two-way Talk
Operating System
Embedded LINUX
Recording
Display
Interface
1 HDMI, 1 VGA
Resolution
1920 × 1080 , 1280 × 1024, 1280 × 720 , 1024 × 768
Multi-screen Display
1/4
OSD
Camera title, Time, Video loss, Camera lock,
Motion detection, Recording
Video Detection and Alarm
Compression
H.264/MJPEG
Resolution
5MP/ 4MP/ 3MP/ 1080P/ 1.3MP/ 720P etc.
Record Rate
80Mbps
Bit Rate
16Kbps ~ 20Mbps Per Channel
Record Mode
Manual, Schedule (Regular, Continuous), MD
(Video detection: Motion Detection, Camera Blank,
Video Loss), Stop
Record Interval
1 ~ 120 min (default: 60 min), Pre-record:
1 ~ 30 sec, Post-record: 10 ~ 300 sec
Trigger Events
Recording, PTZ, Tour, Video Push, Email, FTP,
Snapshot, Buzzer and Screen Tips
Video Detection
Motion Detection, MD Zones: 396 (22 × 18),
Video Loss and Camera Blank
Interface
1 RJ-45 Port (10/100Mbps)
Alarm input
N/A
Ethernet Port
1 Independent 100Mbps Ethernet Port
Relay Output
N/A
PoE
N/A
Network Function
HTTP, TCP/IP, IPv4/IPv6, UPnP, RTSP, UDP, SMTP,
NTP, DHCP, DNS, IP Filter, PPPoE,DDNS, FTP,
IP Search (Support Dahua IP camera, DVR, NVS,
etc.)
Max. User Access
128 users
Smart Phone
iPhone, iPad, Android
Interoperability
ONVIF 2.4, CGI Conformant
Playback and Backup
Playback
1/4
Search Mode
Time /Date, MD and Exact Search
(accurate to second), Smart search
Playback Function
Play, Pause, Stop, Rewind, Fast play, Slow Play,
Next File, Previous File, Next Camera,
Previous Camera, Full Screen, Repeat, Shuffle,
Backup Selection, Digital Zoom
Backup Mode
USB Device/Network
Storage
Internal HDD
1 SATA III Ports, Up to 6 TB capacity for each HDD
HDD Mode
Single
eSATA
N/A
Network
Electrical
Power Supply
Single, DC12V/2A
Power Consumption
<10W (Without HDD)
Environmental
Operating Conditions
-10°C ~ +55°C (+14°F ~ +131°F), 86 ~ 106kpa
Storage Conditions
-20°C ~ +70°C (-4°F ~ +158°F), 0 ~ 90% RH
Construction
Auxiliary Interface
USB
2 USB Ports (2 USB2.0)
Dimensions
260mm x 246.4mm x 47.6mm
(10.24" x 9.7" x 1.87")
RS232
N/A
Net Weight
0.5kg (1.1 lb) (Without HDD)
RS485
N/A
Gross Weight
2.0kg (4.4 lb)(Without HDD)
Certifications
Third-party Support
Third-party Support
Dahua, Arecont Vision, AXIS, Bosch, Brickcom,
Canon, CP Plus, Dynacolor, Honeywell, Panasonic,
Pelco, Samsung, Sanyo, Sony, Videotec, Vivotek,
and more
CE
Coming soon
FCC
Coming soon
2 Front Panel and Rear Panel
2.1 Front Panel
Figure 2-4
Please refer to the following sheet for front panel button information.
Icon
Name
Function
HDD
HDD status indicator
light
The blue light is on when the HDD is malfunction.
NET
Network status indicator
light
The blue light is on when the network connection is
abnormal.
POWER
Power status indicator light
The blue light is on when the power connection is
OK.
USB2.0 port
Connect to peripheral USB 2.0 storage device,
mouse, burner and etc.
78
2.2.8 Compact 1U Wireless Series
The rear panel is shown as below. See Figure 2-35.
Figure 2-35
Please refer to the following sheet for detailed information.
Icon
Name
Power
socket.
Function
input
Power socket. Input DC12V/2A.
Network port
10M/100Mbps self-adaptive Ethernet port. Connect to
the network cable.
USB2.0 port
USB2.0 port. Connect to mouse, USB storage device,
and etc.
HDMI
High
Definition
Media Interface
High definition audio and video signal output port. It
transmits uncompressed high definition video and
multiple-channel data to the HDMI port of the display
device. HDMI version is 1.4.
VGA
VGA video output
port
VGA video output port. Output analog video signal. It
can connect to the monitor to view analog video.
GND
Ground end
Wireless AP
Support wireless hotspot function. Use WIFI to
connect to the network camera when there is a
hotspot.
103
2.3 Alarm Connection
2.3.1 Alarm Port
The alarm port is shown as below. See Figure 2-81. The following figure is based on the professional 2U
series.
Figure 2-81
Icon
Function
1~16
ALARM1~ALARM16. The alarm becomes activated in the
low level.
NO1 C1,NO2 C2,NO3 C3,NO4
C4
Four NO activation output groups. (On-off button).
NO5 C5 NC5
One NO/NC activation output group. (On-off button).
CTRL 12V
Control power output. Disable power output when alarm is
canceled. Current is 500mA.
+12V
Rated current output. Current is 500mA.
GND
A/B
485 communication port. They are used to control devices
such as PTZ. Please parallel connect 120TΩ between A/B
cables if there are too many PTZ decoders.
Note
 Different models support different alarm input ports. Please refer to the specifications sheet for
detailed information.
 Slight difference may be found on the alarm port layout.
2.3.2
Alarm input port
Connect the positive end (+) of the alarm input device to the alarm input port (ALARM IN 1~16) of the
NVR. Connect the negative end (-) of the alarm input device to the ground end (
) of the NVR.
145
Figure 2-82
Note
 There are two alarm input types: NO/NC.
 When connect the ground port of the alarm device to the NVR, you can use any of the GND ports
).
(


Connect the NC port of the alarm device to the alarm input port (ALARM) of the NVR.
When there is peripheral power supplying for the alarm device, please make sure it is earthed with
the NVR.
2.3.3



Alarm input and output port
There is peripheral power supplying for the external alarm device.
In case overload may result in NVR damage, please refer to the following relay specifications for
detailed information.
A/B cable of the RS485 is for the A/B cable connection of the speed PTZ.
2.3.4
Alarm relay specifications
Model:
JRC-27F
Material of the
touch
Silver
Rating
(Resistance
Load)
Rated switch capacity
30VDC 2A, 125VAC 1A
Maximum switch power
125VA 160W
Maximum switch voltage
250VAC, 220VDC
Maximum switch currency
1A
Between touches with same
polarity
1000VAC 1minute
Insulation
146
Surge voltage
Between touches with different
polarity
1000VAC 1minute
Between touch and winding
1000VAC 1minute
Between touches with same
polarity
1500V (10×160us)
Length of open
time
3ms max
Length of close
time
3ms max
Longevity
Mechanical
50×106 MIN (3Hz)
Electrical
200×103 MIN (0.5Hz)
Temperature
-40℃ ~+70℃
2.4 Bidirectional talk
2.4.1
Device-end to PC-end
Device Connection
Please connect the speaker or the pickup to the first audio input port in the device rear panel. Then
connect the earphone or the sound box to the audio output port in the PC.
Login the Web and then enable the corresponding channel real-time monitor.
Please refer to the following interface to enable bidirectional talk. See Figure 2-83.
Figure 2-83
Listening Operation
At the device end, speak via the speaker or the pickup, and then you can get the audio from the earphone
or sound box at the pc-end. See Figure 2-84.
Figure 2-84
2.4.2 PC-end to the device-end
Device Connection
Connect the speaker or the pickup to the audio output port in the PC and then connect the earphone or
the sound box to the first audio input port in the device rear panel.
147
Login the Web and then enable the corresponding channel real-time monitor.
Please refer to the above interface (Figure 2-83) to enable bidirectional talk.
Listening Operation
At the PC-end, speak via the speaker or the pickup, and then you can get the audio from the earphone or
sound box at the device-end. See Figure 2-85.
Figure 2-85
2.5 Mouse Operation
Please refer to the following sheet for mouse operation instruction.
Left
click
mouse
When you have selected one menu item, left click mouse to view menu content.
Modify checkbox or motion detection status.
Click combo box to pop up dropdown list
In input box, you can select input methods. Left click the corresponding button
on the panel you can input numeral/English character (small/capitalized). Here
← stands for backspace button. _ stands for space button.
In English input mode: _stands for input a backspace icon and ← stands for
deleting the previous character.
In numeral input mode: _ stands for clear and
previous numeral.
Double left
click mouse
← stands for deleting the
Implement special control operation such as double click one item in the file list
to playback the video.
148
In multiple-window mode, double left click one channel to view in full-window.
Double left click current video again to go back to previous multiple-window
mode.
Right click
mouse
In real-time monitor mode, pops up shortcut menu.
Press middle
button
In numeral input box: Increase or decrease numeral value.
Exit current menu without saving the modification.
Switch the items in the check box.
Page up or page down
Move mouse
Select current control or move control
Drag mouse
Select motion detection zone
Select privacy mask zone.
2.6 Remote Control
The remote control interface is shown as in Figure 2-86.
Please note remote control is not our standard accessory and it is not included in the
accessory bag.
Figure 2-86
Serial Number
Name
Function
1
Power button
Click it to boot up or shut down
the device.
2
Address
Click it to input device number, so
that you can control it.
149
3
Forward
Various forward speeds
normal speed playback.
4
Slow play
Multiple slow play speeds or
normal playback.
Next record
In playback mode, playback the
next video.
Previous record
In playback mode, playback the
previous video.
Play/Pause
In pause mode, click this button
to realize normal playback.
5
6
7
and
In normal playback click this
button to pause playback.
In real-time monitor mode, click
this button to enter video search
menu.
Reverse/pause
8
Reverse playback pause mode,
click this button to realize normal
playback.
In reverse playback click this
button to pause playback.
Esc.
Go back to previous menu or
cancel current operation (close
upper interface or control)
10
Record
Start or stop record manually
In record interface, working with
the direction buttons to select the
record channel.
Click this button for at least 1.5
seconds, system can go to the
Manual Record interface.
11
Direction keys
Switch current activated control,
go to left or right.
In playback mode, it is to control
the playback process bar.
Aux function(such as switch the
PTZ menu)
12
Enter /menu key
go to default button
go to the menu
13
Multiple-window switch
Switch between multiple-window
and one-window.
14
Fn
In 1-ch monitor mode: pop up
assistant function : PTZ control
and Video color.
9
Switch the PTZ control menu in
PTZ control interface.
150
In motion detection interface,
working with direction keys to
complete setup.
In text mode, click it to delete
character.
15
0-9 number key
Input password,
switch channel.
channel
or
Shift is the button to switch the
input method.
151
3 Device Installation
Note: All the installation and operations here should conform to your local electric safety rules.
3.1 Check Unpacked NVR
When you receive the NVR from the forwarding agent, please check whether there is any visible damage.
The protective materials used for the package of the NVR can protect most accidental clashes during
transportation. Then you can open the box to check the accessories.
Please check the items in accordance with the list. Finally you can remove the protective film of the NVR.
3.2 About Front Panel and Rear Panel
The model number in the stick on the bottom of NVR is very important; please check according to your
purchase order.
The label in the rear panel is very important too. Usually we need you to represent the serial number
when we provide the service after sales.
3.3 HDD Installation
Important:
Please turn off the power before you replace the HDD.
The pictures listed below for reference only.
For the first time install, please be aware that whether the HDDs have been installed.
You can refer to the Appendix for HDD space information and recommended HDD brand. Please use
HDD of 7200rpm or higher. Usually we do not recommend the PC HDD.
Please follow the instructions below to install hard disk.
3.3.1 Smart Box Series
Please make sure the metal surface of the HDD is facing up when you are installing!
This series NVR has only one 2.5-inch SATA HDD.
Please follow the instructions below to install HDD.
1 Draw out the HDD bracket
○
2 Make
○
sure the HDD metal
3 Put the HDD into the device.
○
surface is facing up and then put
the
HDD
into
the
bracket
152
horizontally. After the HDD is in
the proper position, the columns
on the two sides can lock the
screw holes of the HDD to secure
it.
When you remove the HDD, please refer to the following figure to pull the spring up and then remove the
HDD.
3.3.2 Smart 1U Series
Note
Connect cable and then secure the HDD on the NVR if it is not convenient to connect the HDD data cable
and power cable at first.
1 . Loosen the screws of the bottom of ○
2
○
the chassis.
4
○
Connect the HDD cable and power
Place
the
HDD
in
3
○
Turn the device upside
accordance with the four holes in
down
the bottom.
screws firmly.
5
○
and
then
secure
the
Put the cover back and then
cable to the HDD and the mainboard
fix the screws of the rear panel.
respectively.
The installation is complete.
153
3.3.3 Mini 1U/Compact 1U Series
1 . Loosen the screws of the upper ○
2
○
cover and side panel.
4
○
Place the HDD in accordance
Connect the one end of the
3
○
Connect the other end of the
HDD data cable and the power
HDD data cable and the power
cable to the mainboard.
cable to the HDD.
5
○
6
○
Turn the device upside down;
Put the cover in accordance
with the four holes on the bottom of
fix the screws to secure the HDD
with the clip and then fix the
the chassis.
on the bottom of the chassis.
screws on the rear panel and side
panel.
3.3.4 1U Series
The following figures are based on the professional 1U with 8 PoE ports series.
Note
Connect cable and then secure the HDD on the NVR if it is not convenient to connect the HDD data cable
and power cable at first.
1 Loosen the screws of the rear
○
②Place the HDD in accordance with
③Turn the device upside down and
panel and side panel.
the four holes in the bottom.
then secure the screws firmly. It is to
fix the HDD on the chassis.
154
④Connect the HDD cable and power
⑤ Put the cover in accordance with
cable.
the clip and then fix the screws on the
rear panel and side panel.
3.3.5 1.5U Series
①
Use the screwdriver to loose the screws of the rear
panel and then remove the front cover.
③ Connect to the HDD data cable to the main board
and the HDD port respectively. Loosen the power
cable of the chassis and connect another end of the
power cable to the HDD port.
②
Put the HDD to the HDD bracket in the chassis
and then line up the four screws to the four holes
in the HDD. Use the screwdriver to fix the screws
firmly to secure HDD on the HDD bracket
④ After connect the cable, put the front cover back to
the device and then fix screws of the rear panel.
3.3.6 General 2U Series
The following figures are based on the Professional 2U series.
155
① ①Use the screwdriver to loose the screws
of the rear panel and then remove the front
cover.
② ②Put the HDD to the HDD bracket in
the chassis and then line up the four
screws to the four holes in the HDD.
Use the screwdriver to fix the screws
firmly to secure HDD on the HDD
bracket
③Connect to the HDD data cable to the main board
④After connect the cable, put the front cover
and the HDD port respectively. Loosen the power cable
back to the device and then fix screws of the rear
of the chassis and connect another end of the power
panel.
cable to the HDD port.
3.3.7 Professional 2U with RAID series
①Turn the key into the hole in the front
panel.
②Open the front panel.
156
③ Put the HDD to the slot and adjust the
handle to secure it.
④Put the front panel back and use the key to fix
firmly.
HDD Handle Installation
①Line up the handle to the HDD side (without
the interface)
②Use the screwdriver to fix the handle on the
HDD.
3.3.8 3U Series
①Use four screws to secure the HDD.
②Put the HDD to the HDD box at the front
panel of the device. .
157
③Please pull the handle up when you are
inputing the HDD box in case the the handle
collides with the front panel
④Put the HDD to the HDD box at the front
panel of the device. .
3.3.9 Beneficio Vertical 1U Series
①Use 4 screws to secure the HDD
②Put the HDD to the HDD box at the front.
③Pull the HDD knob up when you put the HDD
④Put the knob back after you insert the HDD
into the box in case the knob buckle may strike
to the SATA board.
the front panel.
.
3.4 CD-ROM Installation
Please follow the steps listed below.
158
① Open top cover and then remove the
HDD bracket
② Take off the bottom of the HDD bracket and CD-ROM
bracket.
③ Fix the CD-ROM bracket at the HDD
bracket.
④ Install a pair of the CD-ROM bracket. Please make
sure the reverse side is secure too.
⑤ Install SATA burner. Line up the SATA
burner to the hole positions.
⑥
User screwdriver to fix the screws.
159
⑦ Put the bracket back. Please adjust the
CD-ROM to the proper position so that
the button of the front panel is directly
facing the pop-up button of the CD-ROM.
⑧ Connect the SATA cable and power wire.
⑨ Secure the HDD bracket and put the top
cover back.
3.5 Connection Sample
3.5.1 Smart box/Smart box with 1 PoE port Series
Please refer to Figure 3-1 for connection sample.
Here we take smart box with 1 PoE port as an example.
160
Figure 3-1
3.5.2 Entry-level smart 1U/ Entry-level smart 1U with 1 PoE port / Beneficio smart 1U
/ Beneficio smart 1U with 1 PoE port / Beneficio smart 1U with 8 PoE ports /
Beneficio smart 1U with wireless/ Beneficio Smart 1U(S2)/ 4K smart 1U (S2)
Series
Please refer to Figure 3-2 for connection sample.
Here we take Beneficio smart 1U as an example.
161
Figure 3-2
3.5.3 Entry-level mini 1U / Entry-level mini 1U with 1 PoE port/ Beneficio mini 1U /
Beneficio mini 1U with 1 PoE port / Beneficio mini 1U with 8 PoE ports Series
Please refer to Figure 3-3 for connection sample.
Here we take beneficio mini 1U as an example.
162
Figure 3-3
3.5.4 Compact 1U Series
Please refer to Figure 3-4 for connection sample.
163
Figure 3-4
3.5.5 Compact 1U Wireless Series
Please refer to Figure 3-5 for connection sample.
164
Figure 3-5
3.5.6 Compact 1U(S2)/4K compact 1U (S2) Series
Please refer to Figure 3-6 for connection sample.
Please note the following figure is based on the compact 1U (S2) with 8 PoE ports series.
165
Figure 3-6
3.5.7 Beneficio 1U (S2) Series
Please refer to Figure 3-7 for connection sample.
Please note the following figure is based on the 8 PoE ports series.
166
Figure 3-7
3.5.8 Beneficio Entry-level 1U Series
Please refer to Figure 3-8 for connection sample.
Figure 3-8
167
3.5.9 Beneficio 1U / Beneficio 1U with 1 PoE port / Beneficio 1U with 8 PoE ports/
Beneficio 1U with 16 PoE ports/ Professional 4K 1U/ Professional 4K 1U with 8
PoE ports/ Professional 4K 1U with 16 PoE ports Series
Please refer to Figure 3-9 for connection sample.
The following figure is based on our beneficio 1U with 8 PoE ports product.
Figure 3-9
3.5.10 Beneficio 4K 1U/General 4K 1U (S2) Series
Please refer to Figure 3-10 for connection sample.
The following figure is based on our beneficio 4K series product.
168
Figure 3-10
3.5.11 Beneficio 4K 1U with 8 PoE ports/4K 1U (S2) with 4 PoE ports/4K 1U (S2) with 8
PoE ports/4K 1U (S2) with 16 PoE ports Series
Please refer to Figure 3-11 for connection sample.
The following figure is based on our beneficio 4K 1U with 8 PoE ports series product.
Figure 3-11
169
3.5.12 Beneficio 4K 1.5U / Beneficio 4K 2U/ Professional 4K 1.5U/ Professional 4K
1.5U with 16 PoE ports/ Professional 4K 2U / Professional 4K 2U with 16 PoE
ports Series
Please refer to Figure 3-11 for connection sample.
The following interface is based on the beneficio 4K 1.5U series product.
Figure 3-12
3.5.13 Beneficio 1.5U / Beneficio 1.5U with 8 PoE ports / Beneficio 1.5U with 16 PoE
ports/4K 1.5U (S2) Series
Please refer to Figure 3-13 for connection sample.
The following interface is based on the beneficio 1.5U with 8 PoE ports series product.
170
Figure 3-13
3.5.14 Beneficio 2U / Beneficio 2U with 16 PoE ports/4K 2U (S2) Series
Please refer to Figure 3-14 for connection sample.
The following interface is based on the beneficio 2U with 16PoE ports series product.
Figure 3-14
171
3.5.15 Professional 1U Series
Please refer to Figure 3-15 for connection sample.
Figure 3-15
3.5.16 Professional 1U with 8 PoE ports Series
Please refer to Figure 3-16 for connection sample.
172
Figure 3-16
3.5.17 Professional 1.5U Series
Please refer to Figure 3-17 for connection sample.
173
Figure 3-17
3.5.18 Professional 1.5U with 8 PoE ports / Professional 1.5U with 16 PoE ports Series
Please refer to Figure 3-18 for connection sample.
The following figure is based on the professional 1.5U with 8 PoE ports series product.
174
Figure 3-18
3.5.19 Professional 2U Series
Please refer to Figure 3-19 for connection sample.
175
Figure 3-19
3.5.20 Professional 2U with 16 PoE ports Series
Please refer to Figure 3-20 for connection sample.
176
Figure 3-20
3.5.21 Professional 2U with RAID series
Please refer to Figure 3-21 for connection sample.
177
Figure 3-21
3.5.22 Professional 3U Series
Please refer to Figure 3-22 for connection sample.
178
Figure 3-22
3.5.23 Professional 3U with two HDMI ports Series
Please refer to Figure 3-23 for connection sample.
179
Figure 3-23
3.5.24 Beneficio Vertical 1U Series
Please refer to Figure 3-24 for connection sample.
180
Figure 3-24
181
4 Local Basic Operation
4.1 Getting Started
4.1.1 Boot up and Shut down
4.1.1.1 Boot up
Warning
Before the boot up, please make sure:
 For device security, please connect the NVR to the power adapter first and then connect the device
to the power socket.
 The rated input voltage matches the device power on-off button. Please make sure the power wire
connection is OK. Then click the power on-off button.
 Always use the stable current, if necessary UPS is a best alternative measure.
Please follow the steps listed below to boot up the device.
 Connect the device to the monitor and then connect a mouse.
 Connect power cable.
 Click the power button at the front or rear panel and then boot up the device. After device booted up,
the system is in multiple-channel display mode by default.
4.1.1.2 Shutdown
Note


When you see corresponding dialogue box “System is shutting down…” Do not click power on-off
button directly.
Do not unplug the power cable or click power on-off button to shutdown device directly when device
is running (especially when it is recording.)
There are three ways for you to log out.
a) Main menu (RECOMMENDED)
From Main Menu->Shutdown, select shutdown from dropdown list.
Click OK button, you can see device shuts down.
b) From power on-off button on the front panel or remote control.
Press the power on-off button on the NVR front panel or remote control for more than 3 seconds to
shut down the device.
c)
From power on-off button on the rear panel.
4.1.2 Device Initialization
If it is your first time to use the device, please set a login password admin (system default user).
Note
For your device safety, please keep your login password of admin well after the initialization steps, and
change the password regularly.
Please follow the steps listed below.
182
Step 1
Boot up NVR.
Device displays device initialization interface. See Figure 4-1.
Figure 4-1
Step 2



Set login password of admin.
User name: The default user name is admin.
Password/confirm password: The password ranges from 8 to 32 digitals. It can contain letters,
numbers and special characters (excluding “'”,“"”,“;”,“:”,“&”) . The password shall
contain at least two categories. Usually we recommend the strong password.
Prompt question: If you set the prompt question here. On the login interface, click
, device
can display the corresponding prompt question for you to remind the password.
WARNING
Step 3
STRONG PASSWORD RECOMMENDED-For your device own safety, please create a
strong password of your own choosing. We also recommend you change your password
periodically especially in the high security system.
Click Next, device goes to the following interface. See Figure 4-2.
183
Figure 4-2
Step 4
Set unlock pattern.
After set unlock pattern, device goes to password protection interrface. See Figure 4-3.
Note


Device adopts unlock pattern to login by default if you have set pattern here. If there is no
unlock pattern, please input the password to login.
Click Skip if there is no need to set unlock pattern.
184
Figure 4-3
Step 5
Set security questions.
Note




After setting the security questions here, you can use the email you input here or answer the
security questions to reset admin password. Refer to chapter 4.1.3 Reset password for detailed
information.
Cancel the email or security questions box and then click Next button to skip this step.
Email: Input an email address for reset password purpose. In case you forgot password in the
future, input the security code you got on the assigned email to reset the password of admin. If
you have not input email here or you need to update the email information, please go to the
main menu->Setting->System->Account to set. Refer to chapter 4.10.1 for detailed information.
Security question: Set security questions and corresponding answers. Properly answer the
questions to reset admin password. In case you have not input security question here or you
need to update the security question information, please go to the main
menu->Setting->System->Account->Security question to set. Refer to chapter 4.10.1.1.5
Security question for detailed information.
Note
Step 6
If you want to reset password by answering security questions, please go to the local menu
interface.
Click OK to complete the device initialization setup.
185
Device goes to startup wizard interface. Refer to chapter 4.1.4 Startup wizard for detailed
information.
4.1.3
Reset Password
If you forgot admin password, you can reset the password by email or by answering the security
questions.
Please follow the steps listed below.
Step 1 Go to the device login interface. See Figure 4-4 or Figure 4-5. .
 If you have set unlock pattern, device displays unlock pattern login interface. See Figure 4-4.
Click “Forgot unlock pattern”, device goes to Figure 4-5.
 If you have not set unlock pattern, device displays password interface. See Figure 4-5.
Note
Click Switch user button or click the user name and then select a user from the dropdown list, you
can login via other account.
Figure 4-4
186
Figure 4-5
Step 2


Click
.
If you have not input email address information when you are initializing the device, the interface
is shown as in Figure 4-6. Please input an email address and then click Next button, devices
goes to Figure 4-7.
If you have input email when you are initializing the device, device goes to Figure 4-7.
Figure 4-6
187
Figure 4-7
Step 3
Reset login password.
There are two ways to reset the password: Scan QR code and reset by email/security questions
(local menu only)
 Email
In Figure 4-7, follow the prompts on the interface to scan the QR code, and then input the
security code you get via the assigned email.
Warning


For the same QR code, max scan twice to get two security codes. Refresh the QR
code if you want to get security code again.
 The security code on your email is only valid for 24 hours.
Security questions
In Figure 4-6., select security question from the drop down list. Device displays security
question interface. See Figure 4-8. Please input the correct answers here.
188
Figure 4-8
Step 4
Click Next button.
Device displays reset password interface. See Figure 4-9.
Figure 4-9
Step 5
Input new password and then confirm.
WARNING
STRONG PASSWORD RECOMMENDED-For your device own safety, please create a
strong password of your own choosing. The password shall be at least 8-digit containing
at least two types of the following categories: letters, numbers and symbols. We also
189
Step 6
recommend you change your password periodically especially in the high security
system.
Click OK button to complete the setup.
4.1.4 Startup Wizard
After you successfully initialize the device, it goes to startup wizard. Here you can quickly configure your
device. It includes smart add, general setup, basic network setup, camera registration, P2P, and schedule
interface.
Please follow the steps listed below.
Step 1 Boot up the device.
Device goes to startup wizard if you have successfully initialized the device. See Figure 4-10.
Note



Check the Startup button here, device goes to startup wizard again when it boots up the
next time. Cancel the Startup button, device goes to the login interface directly when it
boots up the next time.
Check the box to enable smart add function, and then click the Next button. Device now
adds the camera. Refer to chapter 4.1.4.1 Smart Add for detailed information. Please note
this function is for some series product only.
Click the Cancel button, device goes to login interface. Device is in multiple-window preview
mode by default. Refer to chapter 4.3 Preview for detailed information.
Figure 4-10
Step 2
Click Next button.
 Device displays unlock pattern login interface if you have set unlock pattern. See Figure
4-11. Click forgot pattern, device goes to password login interface. See
190

If you have not set unlock pattern, device displays password login interface. See Figure
4-12.
Figure 4-11
Figure 4-12
Step 3
Draw unlock pattern or input login password.
Warning

The account becomes locked after five times login failure by default. After each login failure,
191
Step 4
you can see the remaining login attempts.
 Refer to chapter 4.7.11 (Main menu->Setting->Event->Abnormality->User) to set login
attempt times (1-10) and account lock time (1 to 30 minutes).
Click OK button.
Device goes to startup wizard, now you can quickly configure the device.
4.1.4.1 Smart Add
When the network camera(s) and the device are in the same router or switch, you can use smart add
function to add network cameras to the device.
Please follow the steps listed below.
Step 1 There are two ways to go to the smart add interface. See Figure 4-15.
 From the startup wizard, click Smart add button and then click Next. See Figure 4-13.
Figure 4-13

On the preview interface, right click mouse and then select Smart add. See Figure 4-14.
192
Figure 4-14
Figure 4-15
Step 2
Set network camera login password.
WARNING
193
Step 3
STRONG PASSWORD RECOMMENDED-For your device own safety, please create a
strong password of your own choosing. The password shall be at least 8-digit
containing at least two types of the following categories: letters, numbers and
symbols. We also recommend you change your password periodically especially in
the high security system.
Click Next button to continue.
1) Device now enable DHCP function. It says it is DHCP now, please wait. See Figure 4-16.
Figure 4-16
2)
Device goes to change IP address interface. Please change IP address if necessary and
then click OK button. See Figure 4-17. Please note this step is optional.
Note
Please make sure there are several IP segments in the LAN. Otherwise, you can skip this
step.
194
Figure 4-17
3)
After complete DHCP function, device is automatically adding network camera to the
corresponding channels. See Figure 4-18.
Figure 4-18
195
4)
Step 4
Device pops up following dialog box after it successfully added network cameras. See
Figure 4-19.
Figure 4-19
Click YES button to complete smart add operation.
4.1.4.2 General
After you successfully logged in the startup wizard, device goes to General interface. Here you can set
NVR basic information.
4.1.4.2.1
General
It is to set device basic information such as device name, serial number and etc.
Please follow the steps listed below.
Step 1 Click General button.
The interface is shown as below. See Figure 4-20.
Note
Step 2
From Main menu->Setting->System->General->General, you can go to the general
interface.
Set parameters.
 Device ID: Please input a corresponding device name here.
 Device No: When you are using one remote control (not included in the accessory bag) to
control several NVRs, you can give a name to each NVR for your management.
 Language: System supports various languages: Chinese (simplified), Chinese (Traditional),
English, Italian, Japanese, French, Spanish (All languages listed here are optional. Slight
difference maybe found in various series.)
 Video standard: There are two formats: NTSC and PAL.
 HDD full: Here is for you to select working mode when hard disk is full. There are two
options: stop recording or rewrite old files.
 Pack duration: Here is for you to specify record duration. The value ranges from 1 to 120
minutes. Default value is 60 minutes.
 Realtime play: It is to set playback time you can view in the preview interface. The value
ranges from 5 to 60 minutes.
 Auto logout: Here is for you to set auto logout interval once login user remains inactive for a
specified time. Value ranges from 0 to 60 minutes.
196

Monitor channels when logout: Here you can set channels you want to view when your
account has logged out. Click the button and then cancel the channel name box, you need
to login to view the corresponding video. The channel window displays




in preview
interface.
Navigation bar: Check the box here, system displays the navigation bar on the interface.
IPC Time Sync: You can input an interval here to synchronize the NVR time and IPC time.
Startup wizard: Once you check the box here, system will go to the startup wizard directly
when the system restarts the next time. Otherwise, it will go to the login interface.
Mouse sensitivity: You can set double click speed via dragging the slide bard. You can Click
Default button to restore default setup.
Figure 4-20
Step 3
4.1.4.2.2
Click Apply button to save settings.
Date and Time
Here you can set device time. You can enable NTP function so that the device can sync time with the
NTP.
Step 1 Click Date and time button. See Figure 4-21.
197
Note
From Main menu->Setting->System->General->Date and time, you can go to the date and
time interface.
 System time: Here is for you to set system time
 Date format: There are three types: YYYYY-MM-DD: MM-DD-YYYYY or DD-MM-YYYY.
 Date separator: There are three denotations to separate date: dot, beeline and solidus.
 DST: Here you can set DST time and date by week or by date. Please enable DST function
and then select setup mode. Please input start time and end time and click Save button.
 Time format: There are two types: 24-hour mode or 12-hour mode.
 NTP: It is to set NTP server, port and interval.
Warning


System time is very important; do not modify time casually unless there is a must!
Before your time modification, please stop record operation first!
Figure 4-21
Step 4
Click Apply button to save settings.
198
4.1.4.2.3
Holiday
Here you can add, edit, delete holiday. After you successfully set holiday information, you can view
holiday item on the record and snapshot period.
Step 1 Click Holiday button. See Figure 4-22.
Note
From Main menu->Setting->System->General->Holiday, you can go to the holiday interface.
Figure 4-22
Step 2
Click Add new holiday button, device displays the following interface. See Figure 4-23.
199
Figure 4-23
Step 3
Set holiday name, repeat mode and holiday mode.
Note
Step 4
Click Add more to add new holiday information.
Click Add button, you can add current holiday to the list.
Note
Step 5

Click the dropdown list of the state; you can enable/disable holiday date.

Click
to change the holiday information. Click
to delete current date.
Click Apply button to save settings.
4.1.4.3 Basic Network Settings
Set device IP address, DNS information so that the device can connect to other devices.
Preparation
Make sure the device has properly connected to the network.
Step 1 Click Next button, device goes to TCP/IP interface. See Figure 4-24.
Note


From Main menu->Setting->Network->TCP/IP, you can go to the TCP/IP interface.
Different series products have different Ethernet adapter amount and type. Please refer to
the actual product.
200
Figure 4-24
Step 2
Click
, device display edit interface. See Figure 4-25.
201
Figure 4-25
Step 3



Set parameters.
 Network Mode : Includes multiple access, fault tolerance, and load balancing
Multiple-address mode: eth0 and eth1 operate separately. You can use the services such as
HTTP, RTP service via etho0 or the eth1. Usually you need to set one default card (default
setup is etho) to request the auto network service form the device-end such as DHCP, email,
FTP and etc. In multiple-address mode, system network status is shown as offline once one
card is offline.
Network fault-tolerance: In this mode, device uses bond0 to communicate with the external
devices. You can focus on one host IP address. At the same time, you need to set one master
card. Usually there is only one running card (master card).System can enable alternate card
when the master card is malfunction. The system is shown as offline once these two cards are
both offline. Please note these two cards shall be in the same LAN.
Load balance: In this mode, device uses bond0 to communicate with the external device. The
eth0 and eth1 are both working now and bearing the network load. Their network load are
general the same. The system is shown as offline once these two cards are both offline. Please
note these two cards shall be in the same LAN.
 Main Network Card: Please select eth0/eth1 (optional).after enable multiple access
function.
Note
The dual-Ethernet port series support the above three configurations and supports
functions as multiple-access, fault-tolerance and load balancing.


MAC address: The host in the LAN can get a unique MAC address. It is for you to access in
the LAN. It is read-only.
IP address: Here you can use up/down button () or input the corresponding number to
input IP address. Then you can set the corresponding subnet mask the default gateway.
202

Step 4
Default gateway: Here you can input the default gateway. Please note system needs to
check the validity of all IPv6 addresses. The IP address and the default gateway shall be in
the same IP section. That is to say, the specified length of the subnet prefix shall have the
same string.
 DHCP: It is to auto search IP. When enable DHCP function, you cannot modify IP/Subnet
mask /Gateway. These values are from DHCP function. If you have not enabled DHCP
function, IP/Subnet mask/Gateway display as zero. You need to disable DHCP function to
view current IP information. Besides, when PPPoE is operating, you cannot modify
IP/Subnet mask /Gateway.
 MTU: It is to set MTU value of the network adapter. The value ranges from 1280-7200 bytes.
The default setup is 1500 bytes. Please note MTU modification may result in network
adapter reboot and network becomes off. That is to say, MTU modification can affect
current network service. System may pop up dialog box for you to confirm setup when you
want to change MTU setup. Click OK button to confirm current reboot, or you can click
Cancel button to terminate current modification. Before the modification, you can check the
MTU of the gateway; the MTU of the NVR shall be the same as or is lower than the MTU of
the gateway. In this way, you can reduce packets and enhance network transmission
efficiency.
The following MTU value is for reference only.
 1500: Ethernet information packet max value and it is also the default value. It is the typical
setup when there is no PPPoE or VPN. It is the default setup of some router, switch or the
network adapter.
 1492: Recommend value for PPPoE.
 1468: Recommend value for DHCP.
 Transfer mode: Here you can select the priority between fluency/video qualities.
 LAN download: System can process the downloaded data first if you enable this function.
The download speed is 1.5X or 2.0X of the normal speed.
Click OK to NIC settings.
Device goes back to TCP/IP interface.
Note
Click
Step 5
Step 6
to cancel NIC bonding. Please note device needs to reboot to activate new setup.
Set network parameters.
 IP Version: There are two options: IPv4 and IPv6. Right now, system supports these two IP
address format and you can access via them.
 Preferred DNS server: DNS server IP address.
 Alternate DNS server: DNS server alternate address.
 Default Network Card: Please select eth0/eth1/bond0(optional) after enable multiple-access
function
Click Next to complete the settings.
4.1.4.4 P2P
Click Next button, you can set P2P function. Scan the QR code, download the App to the cell phone, you
can use the smart phone to add the device.
203
Warning
Before use the P2P function, make sure the device has connected to the WAN.
Please follow the steps listed below.
Step 1 Click Next button.
Enter P2P interface. See Figure 4-26.
Note
From main menu->Setting->Network->P2P, you can go to P2P interface.
Figure 4-26
Step 2 Check the box to enable P2P function.
Step 3 Click Next button to complete setup.
The status is online if the P2P registration is successful.
Client Operation
Please follow the steps listed below.
Step 1 Use the cell phone to scan the QR code on the interface and then download and install the cell
phone app.
Step 2
Open App; tap
to go to the Live preview.
204
Step 3
Tap
at the top left corner, you can see the main menu.
Step 4
Tap Device manager button, you can use several modes (P2P/DDNS/IP and etc.) to add the
device. Click
to save current setup. Tap Start Live preview to view all-channel video from
the connected device. See Figure 4-27.
Figure 4-27
Step 5
Click Start live preview to view real-time video.
4.1.4.5 Registration
Here you can add network camera, change network camera IP address and etc.
Step 1 Click Next button.
Enter remote device interface. See Figure 4-28.
Note


There are two ways to go to Registration interface.
From main menu->Setting->Camera->Registration, you can go to the registration interface.
On the preview interface, right click mouse and then select Registration.
205
Figure 4-28
Step 2
Set parameters
 Channel: It is the device channel number. If you have not added the network camera, the
channel number is shown as .

Status: Red circle (


current channel has video.
IP address: It is to display network camera IP address.
Type: There are two connection types. You can use the network to connect to the camera or
use the WIFI. The
) means current channel has no video, green circle (
) means
means current network camera connection mode is general; the
means current network camera mode is hotspot.
Step 3
 Add/Delete: Click
to delete the device, click
to add the device to the NVR.
Add network camera.
 Device search: Click the button; you can search all network cameras in the same network
segment. See Figure 4-29. Double click a camera or check the camera box and then click
Add button, you can add a device to the list.
Note
The device in the added device list is not shown in the search result column.
206
Figure 4-29

Manual Add: Click Manual Add button, you can set the corresponding network camera
information and then select the channel you want to add. See Figure 4-30.
 Manufacturer: Please select from the dropdown list.
Note
Different series products may support different manufactures, please refer to the actual
product.
 IP address: Input remote device IP address.
 RTSP port: Input RTSP port of the remote device. The default setup is 554.
Note
Skip this item if the manufacture is private or customize.
 HTTP port: Input HTTP port of the remote device. The default setup is 80.
Note
Skip this item if the manufacture is private or customize.
 TCP port: Input TCP port of the remote device. The default setup is 37777.
 User name/password: The user name and password to login the remote device.
207
 Channel No.: Input channel amount or click the Connect button to get the channel
amount of the remote device.
Note
We recommend click Connect button to get remote device channel amount, the manual add
operation may result in failure if the input channel amount is not right.
 Remote channel No.: After getting the remote device channel amount, click Setup to
select a channel.
Note
Click to select one or more remote channel numbers here.
 Channel: The local channel number you want to add. One channel name has
corresponding one channel number.
 Decode buffer: There are three items: realtime,local,fluent.
 Service type: There are four items: auto/TCP/UDP/MULTICAST(ONVIF device only)
Note
 The default connection mode is TCP if the connection protocol is private.
 There are three items:TCP/UDP/MULTICAST if the connection protocol is ONVIF.
 There are two items: TCP/UDP if the connection protocol is from the third-party.
Figure 4-30
Step 4
Click OK to add the camera to the device.
Note
Click
to change the remote device information. Click
to delete remote device. .
208
4.1.4.6 Schedule
4.1.4.6.1
Schedule Record
All channels are record continuously by default. You can set customized record period and record type.
Step 1 Click Next button.
Enter schedule interface. See Figure 4-31.
Note
From main menu->Setting->Schedule->Record, you can go to the record interface.
Figure 4-31
Step 2
Set parameters.
 Channel: Please select the channel number first. You can select “all” if you want to set for
the whole channels.

: Sync connection icon. Select icon
edited or together. Now the icon is shown as




of several dates, all checked items can be
.
: Click it to delete a record type from one period.
Record Type: Please check the box to select corresponding record type. There are five
types: Regular/MD (motion detect)/Alarm/MD&Alarm/IVS.
Week day: There are eight options: ranges from Saturday to Sunday and all.
Holiday: It is to set holiday setup. Please note you need to go to the General interface (Main
Menu->Setting->System->General) to add holiday first. Otherwise you cannot see this item.
209




Pre-record: System can pre-record the video before the event occurs into the file. The value
ranges from 1 to 30 seconds depending on the bit stream.
Redundancy: System supports redundancy backup function. It allows you backup
recorded file in two disks. You can highlight Redundancy button to activate this function.
Please note, before enable this function, please set at least one HDD as redundant. (Main
menu->Setting->Storage->HDD Manager). Please note this function is null if there is only
one HDD.
ANR: It is to save video to the SD card of the network camera in case the network
connection fails. The value ranges from 0s~43200s. After the network connection resumed,
the system can get the video from the SD card and there is no risk of record loss.
Period setup: Click button
after one date or a holiday, you can see an interface shown
as in Figure 4-32.There are five record types: regular, motion detection (MD), Alarm, MD &
alarm and IVS.
Figure 4-32
Please following the steps listed below to draw the period manually.
a) Select a channel you want to set. See Figure 4-33.
Figure 4-33
b)
Set record type. See Figure 4-34.
Figure 4-34
210
Note


When the record type is MD (motion detect), alarm, MD&Alarm, IVS, please enable the
channel record function when corresponding alarm occurs. For example, when the alarm
type is MD, from main menu->Setting->Event->Video Detect->Motion Detect, please select
the record channel and enable record function. See Figure 4-35.
When the record type is MD (motion detect), alarm, MD&Alarm, IVS, refer to chapter 4.7.1
Video detect, chapter 4.7.10 Alarm Settings, and chapter 4.7.3 IVS.
Figure 4-35
c)
Please draw manually to set record period. There are six periods in one day. See Figure 4-36.
Note
If you have added a holiday, you can set the record period for the holiday.
211
Figure 4-36
Step 3
Click Apply button to save schedule record settings.
Note
Please enable auto record function so that the record plan can become activated. Refer to chapter
4.1.4.6.3 Record control for detailed information.
4.1.4.6.2
Schedule Snapshot
It is to set schedule snapshot period.
Step 1 Click Snapshot button, device goes to following interface. See Figure 4-37.
Note
From main menu->Setting->Schedule->Snapshot, you can go to the snapshot interface.
212
Figure 4-37
Step 2
Step 3
Step 4
Select a channel to set schedule snapshot.
Set snapshot type as schedule. Refer to chapter 4.2.5.3 Snapshot for detailed information.
Check the box to set alarm type. See Figure 4-38.
Figure 4-38
Note


When the record type is MD (motion detect), alarm, MD&Alarm, IVS, please enable the
channel snapshot function when corresponding alarm occurs. For example, when the alarm
type is MD, from main menu->Setting->Event->Video Detect->Motion Detect, please select
the snapshot channel and enable snapshot function. See Figure 4-39.
When the snapshot type is MD (motion detect), alarm, MD&Alarm, IVS, refer to chapter 4.7.1
Video detect, chapter 4.7.10 Alarm Settings, and chapter 4.7.3 IVS.
213
Step 5
Step 6
Figure 4-39
Refer to chapter 4.1.4.6.1 to set snapshot period.
Click Apply button to save snapshot plan.
Note
Step 7
Please enable auto snapshot function so that the snapshot plan can become activated. Refer to
chapter 4.1.4.6.3 Record control for detailed information.
Click Finish button, system pops up a dialogue box. Click the OK button, the startup wizard is
complete. See Figure 4-40.
Figure 4-40
4.1.4.6.3
Record Control
Note:
214
You need to have proper rights to implement the following operations. Please make sure the HDD
has been properly installed.
There are three ways for you to go to manual record menu.
 Right click mouse and then select Manual->Record.
 In the main menu, from Setting->Storage->Record.
 In live viewing mode, click record button in the front panel or record button in the remote control.
System supports main stream and sub stream. There are three statuses: schedule/manual/stop. See
Figure 4-41. Please highlight icon“○” to select corresponding channel.
 Manual: The highest priority. After manual setup, all selected channels will begin ordinary recording.
 Schedule: Channel records as you have set in recording setup (Main
Menu->Setting->System->>Schedule)
 Stop: Current channel stops recording.
 All: Check All button after the corresponding status to enable/disable all-channel schedule/manual
record or enable/disable all channels to stop record.
Figure 4-41
4.2 Camera
4.2.1 Connection
Device can connect to camera remotely, and can change IP address, import/export IP and etc. Refer to
chapter 4.1.4.5 Registration to add a camera.
4.2.1.1 Change IP address
Step 1
From Main menu->Setting->Camera->Registration, check the box before the camera name and
then click Change IP or click the
before the camera name.
215
Enter change IP interface. See Figure 4-42.
Note
Check the box before several cameras, change the IP addresses of several cameras at the
same time.
Figure 4-42
Step 2
Select IP mode.
Check DHCP, there is no need to input IP address, subnet mask, and default gateway. Device
automatically allocates the IP address to the camera.
Check Static, and then input IP address, subnet mask, default gateway and incremental value.
Note
Step 3
Step 4
If it is to change several devices IP addresses at the same time, please input incremental value.
Device can add the fourth address of the IP address one by one to automatically allocate the IP
addresses.
If there is IP conflict when changing static IP address, device pops up IP conflict dialogue box. If
batch change IP address, device automatically skips the conflicted IP and begin the allocation
according to the incremental value
Input remote device user name and password.
Click OK button to save settings.
After the changing operation, search again, device displays new IP address.
Note
216
When change IP addresses of several devices at the same time, make sure the cameras user
name and passwords are the same.
4.2.1.2 IP Export
Device can export the Added device list to your local USB device.
Step 1 Insert the USB device and then click the Export button.
Enter the following interface. See Figure 4-43.
Figure 4-43
Step 2
Step 3
Select the directory address and then click the OK button.
Device pops up a dialogue box to remind you successfully exported. Please lick OK button to
exit.
Note
The exported file extension name is .CVS. The file information includes IP address, port, remote
channel number, manufacturer, user name and password.
4.2.1.3 IP Import
Step 1
Click Import button.
Enter the following interface. See Figure 4-44.
217
Figure 4-44
Step 2
Step 3
Select the import file and then click the OK button. System pops up a dialogue box to remind you
successfully imported.
Click OK button to exit.
Note
Step 4
If the imported IP has conflicted with current added device, system pops up a dialogue box to
remind you. You have two options:
Click OK button, system uses the imported setup to overlay current one.
Important



You can edit the exported .CVS file. Do not change the file format; otherwise it may result in
import failure.
Does not support customized protocol import and export.
The import and export device shall have the same language format.
4.2.2 Remote Device Initialization
Remote device initialization can change remote device login password and IP address.
Note


When connect a camera to the device via PoE port, device automatically initialize the camera. The
camera adopts device current password and email information by default.
When connect a camera to the device via PoE port, the device may failed to initialize the camera.
Please go to the Registration interface to initialize the camera.
Step 1
From main menu->Setting->Camera->Registration.
Enter Registration interface.
218
Step 2
Step 3
Click Device Search and then click Uninitialized.
Device displays camera(s) to be initialized.
Select a camera to be initialized and then click Initialize.
Device displays password setup interface. See Figure 4-45 and Figure 4-46.
Figure 4-45
219
Step 4
Figure 4-46
Set camera password.
 Using NVR password and email: Check the box to use NVR current admin account and
email information. There is no need to set password and email. Please go to step 7.
 User name/password: The user name is admin. The password ranges from 8 to 32 digitals.
It can contain letters, numbers and special characters (excluding “'”,“"”,“;”,“:”,“&”) . The password
shall contain at least two categories. Usually we recommend the strong password.
WARNING
Step 5
STRONG PASSWORD RECOMMENDED-For your device own safety, please create a
strong password of your own choosing. We also recommend you change your password
periodically especially in the high security system.
Click Next button.
Enter input email interface. See Figure 4-47.
220
Figure 4-47
Step 6
Set email information.
Email: Input an email address for reset password purpose.
Note
Step 7
Cancel the box and then click Next or Skip if you do not want to input email information here.
Click Next button.
Enter Change IP address interface. See Figure 4-48.
221
Figure 4-48
Step 8
Set camera IP address
Check DHCP, there is no need to input IP address, subnet mask, and default gateway. Device
automatically allocates the IP address to the camera.
Check Static, and then input IP address, subnet mask, default gateway and incremental value.
Note

Step 9
If it is to change several devices IP addresses at the same time, please input incremental
value. Device can add the fourth address of the IP address one by one to automatically
allocate the IP addresses.
 If there is IP conflict when changing static IP address, device pops up IP conflict dialogue
box. If batch change IP address, device automatically skips the conflicted IP and begin the
allocation according to the incremental value
Click Next button.
Device begins initializing camera. See Figure 4-49.
222
Figure 4-49
Step 10 Click Finish to complete the setup.
4.2.3 Short-Cut Menu to Add Camera
In the preview interface, for the channel of no IPC connection, you can click the icon “+” in the center of
the interface to quickly go to the registration interface (Figure 4-42.). See Figure 4-50.
Figure 4-50
4.2.4 Image
From main menu->setting->camera->image, you can see the image interface is shown as below. See
Figure 4-51.
 Channel: Select a channel from the dropdown list.
 Saturation: It is to adjust monitor window saturation. The value ranges from 0 to 100. The default
value is 50. The larger the number, the strong the color is. This value has no effect on the general
brightness of the whole video. The video color may become too strong if the value is too high. For
the grey part of the video, the distortion may occur if the white balance is not accurate. Please note
the video may not be attractive if the value is too low. The recommended value ranges from 40 to 60.
223

Brightness: It is to adjust monitor window bright. The value ranges from 0 to 100. The default value is
50. The larger the number is, the bright the video is. When you input the value here, th e bright
section and the dark section of the video will be adjusted accordingly. You can use this function
when the whole video is too dark or too bright. Please note the video may become hazy if the value
is too high. The recommended value ranges from 40 to 60.
 Contrast: It is to adjust monitor window contrast. The value ranges from 0 to 100. The default value
is 50. The larger the number is, the higher the contrast is. You can use this function when the whole
video bright is OK but the contrast is not proper. Please note the video may become hazy if the value
is too low. If this value is too high, the dark section may lack brightness while the bright section may
over exposure .The recommended value ranges from 40 to 60.
 Auto Iris: It is for the device of the auto lens. You can check the box before ON to enable this
function. The auto iris may change if the light becomes different. When you disable this function, the
iris is at the max. System does not add the auto iris function in the exposure control. This function is
on by default.
 Mirror: It is to switch video up and bottom limit. This function is disabled by default.
 Flip: It is to switch video left and right limit. This function is disabled by default.
 BLC: It includes several options: BLC/WDR/HLC/OFF.
 BLC: The device auto exposures according to the environments situation so that the darkest area of
the video is cleared
 WDR: For the WDR scene, this function can lower the high bright section and enhance the
brightness of the low bright section. So that you can view these two sections clearly at the same time.
The value ranges from 1 to 100. When you switch the camera from no-WDR mode to the WDR mode,
system may lose several seconds record video.
 HLC: After you enabled HLC function, the device can lower the brightness of the brightest section
according to the HLC control level. It can reduce the area of the halo and lower the brightness of the
whole video.
 OFF: It is to disable the BLC function. Please note this function is disabled by default.
 Profile: It is to set the white balance mode. It has effect on the general hue of the video. This function
is on by default. You can select the different scene mode such as auto, sunny, cloudy, home, office,
night, disable and etc to adjust the video to the best quality.
 Auto: The auto white balance is on. System can auto compensate the color temperature to make
sure the vide color is proper.
 Sunny: The threshold of the white balance is in the sunny mode.
 Night: The threshold of the white balance is in the night mode.
 Customized: You can set the gain of the red/blue channel. The value reneges from 0 to 100.
 Day/night. It is to set device color and the B/W mode switch. The default setup is auto.
 Color: Device outputs the color video.
 Auto: Device auto select to output the color or the B/W video according to the device feature (The
general bright of the video or there is IR light or not.)
 B/W: The device outputs the black and white video.
 Sensor: It is to set when there is peripheral connected IR light.
Please note some non-IR series product support sensor input function.
224
Figure 4-51
4.2.5 Encode
4.2.5.1 Encode
Encode setting is to set IPC encode mode, resolution, bit stream type and etc
From Main menu->Setting->System->Encode, you can see the following interface. See Figure 4-52.
 Channel: Select the channel you want.
 Type: Please select from the dropdown list. There are three options: regular/motion detect/alarm.
You can set the various encode parameters for different record types.
 Compression: System supports H.264, MPEG4, MJPEG and etc.
 Resolution: The mainstream resolution type is IPC’s encoding config. Generally there is
D1/720P/1080P. For some series product, the main stream supports 2048×1536(3M),1920×1080
(1080P), 1280×1024(S×GA), 1280×960(1.3M),1280×720(720P),704×576(D1)and
the sub stream supports 704×576(D1),352×288(CIF).
 Frame rate: It ranges from 1f/s to 25f/s in NTSC mode and 1f/s to 30f/s in PAL mode.
 Bit rate type: System supports two types: CBR and VBR. In VBR mode, you can set video quality.
 Quality: There are six levels ranging from 1 to 6. The sixth level has the highest image quality.
 Video/audio: You can enable or disable the video/audio. Please note, once you enable audio
function for one channel, system may enable audio function of the rest channels by default.
 Copy:After you complete the setup, you can click Copy button to copy current setup to other
channel(s). You can see an interface is shown as in Figure 4-55. You can see current channel
number is grey. Please check the number to select the channel or you can check the box ALL.
Please click the OK button in Figure 4-55 and Figure 4-53 respectively to complete the setup. Please
note, once you check the All box, you set same encode setup for all channels. Audio/video enable
box, overlay button and the copy button is shield.
225
Please highlight icon
to select the corresponding function.
Figure 4-52
4.2.5.2 Overlay
Click overlay button, you can see an interface is shown in Figure 4-53.
 Cover area: Here is for you to cover area section. You can drag you mouse to set proper section size.
In one channel video, system max supports 4 zones in one channel. You can set with Fn button or
direction buttons.
 Preview/monitor: The cover area has two types. Preview and Monitor. Preview means the privacy
mask zone cannot be viewed by user when system is in preview status. Monitor means the privacy
mask zone cannot be view by the user when system is in monitor status.
 Time display: You can select system displays time or not when you playback. Please click set button
and then drag the title to the corresponding position in the screen.
 Channel display: You can select system displays channel number or not when you playback. Please
click set button and then drag the title to the corresponding position in the screen.
226
Figure 4-53
4.2.5.3 Snapshot
Here you can set snapshot mode, picture size, quality and frequency. See Figure 4-54.
 Snapshot mode: There are two modes: regular and trigger. If you set regular mode, you need to set
snapshot frequency. If you set trigger snapshot, you need to set snapshot activation operation.
 Image size: Here you can set snapshot picture size.
 Image quality: Here you can set snapshot quality. The value ranges from 1 to 6.
 Interval: It is for you to set timing (schedule) snapshot interval.
227
Figure 4-54
Figure 4-55
4.2.6 Channel Name
From main menu->Setting->Camera-Channel name, you can see an interface shown as in Figure 4-56.
It is to modify channel name. It max supports 31-character.
Please note you can only modify the channel name of the connected network camera.
228
Figure 4-56
4.2.7 Remote Upgrade
Note
Right now, the NVR can upgrade the IPC via the USB device or WEB. You can upgrade 8 network
cameras of the same model (or the NVR supported) at the same time.
It is to update the network camera.
From main menu->setting->camera->remote, the interface is shown as below. See Figure 4-57.
Click Browse button and then select the upgrade file. Then select a channel (or you can select device
type filter to select several devices at the same time.)
Click Begin button to upgrade. You can see the corresponding dialogue once the upgrade is finish.
229
Figure 4-57
4.2.8 Remote Device Info
4.2.8.1 Device Status
Here you can view the IPC status of the corresponding channel such as motion detect, video loss,
tampering, alarm and etc. See Figure 4-58.

IPC status:
: Front-end does not support.
event from current front-end.
: Front-end supports.

Connection status:
: Connection failed.

Refresh: Click it to get latest front-end channel status.
: Connection succeeded.
: There is alarm
230
Figure 4-58
4.2.8.2 Firmware
It is to view channel, IP address, manufacturer, type, system version, SN, video input, audio input,
external alarm and etc. See Figure 4-59.
Figure 4-59
231
4.3 Preview
After device booted up, the system is in multiple-channel display mode. See Figure 4-60.Please note the
displayed window amount may vary. The following figure is for reference only. Please refer to chapter 1.3
Specifications for the window-amount your product supported.
Figure 4-60
4.3.1 Preview
If you want to change system date and time, you can refer to general settings (Main
Menu->Setting->System->General). If you want to modify the channel name, please refer to the
display settings (Main Menu->Camera->CAM name)
Please refer to the following sheet for detailed information.
1
Recording status
3
Video loss
2
Motion detection
4
Camera lock
Tips
 Preview drag: If you want to change position of channel 1 and channel 2 when you are
previewing, you can left click mouse in the channel 1 and then drag to channel 2, release mouse
you can switch channel 1 and channel 2 positions.
 Use mouse middle button to control window split: You can use mouse middle button to switch
window split amount.
4.3.2 Navigation bar
On the preview interface, left click mouse, you can view the navigation bar. See Figure 4-61 or Figure
4-62.
Note


Different series products may display different navigation bar icons. Refer to the actual product
for detailed information.
Go to the Main menu->Setting->System->General to enable navigation bar function; otherwise
232
you cannot see the following interface.
Figure 4-61
Figure 4-62
4.3.2.1 Main Menu
Click button
to go to the main menu interface.
4.3.2.2 Dual-screen operation
Important
This function is for some series only.
Click
to select screen 2, you can view an interface shown as below. See Figure 4-63. It is a
navigation bar for screen 2.
Figure 4-63
Click any screen split mode; HDMI2 screen can display corresponding screens. Now you can control two
screens. See Figure 4-64.
Figure 4-64
Note
 Screen 2 function is null if tour is in process. Please disable tour function first,
 Right now, the screen 2 operation can only be realized on the navigation bard. The operations on the
right-click menu are for screen 1 only.
4.3.2.3 Output Screen
Click
to select corresponding window-split mode and output channels.
4.3.2.4 Previous screen/next screen
Click
to go back to the previous screen, click
to go to the next screen.
4.3.2.5 Tour
233
Click button
to enable tour, the icon becomes
, you can see the tour is in process.
Note
Close the tour or the triggered tour operation has cancelled, device restore the previous preview video.
4.3.2.6 PTZ
Click
, system goes to the PTZ control interface. Please refer to chapter 4.4.2 PTZ for detailed
information.
4.3.2.7 Color
Click button
, system goes to the color interface. Please refer to chapter 4.3.6.1 Color for detailed
information.
Please make sure system is in one-channel mode.
4.3.2.8 Image
Click
to go to the image interface. Please refer to chapter 4.2.4 Image for detailed information.
Please make sure system is in one-channel mode.
4.3.2.9 Search
Click button
, system goes to search interface. Please refer to chapter 4.6.2 Search for detailed
information.
4.3.2.10 Broadcast
Click
to go to broadcast interface. Select a group name and then click
to begin
broadcast. Please refer to chapter 4.10.6 Broadcast for detailed information.
4.3.2.11 Alarm Status
Click button
, system goes to alarm status interface. It is to view device status and channel status.
Please refer to chapter 4.10.2.4 Alarm status for detailed information.
4.3.2.12 Channel Info
Click button
, system goes to the channel information setup interface. It is to view information of the
corresponding channel. See Figure 4-65.
234
Figure 4-65
4.3.2.13 Registration
Click
, system goes to the registration interface. Please refer to chapter 4.1.4.6.3 Registration for
detailed information.
4.3.2.14 Network
Click
, system goes to the network interface. It is to set network IP address, default gateway and etc.
Please refer to chapter 4.8 Network for detailed information.
4.3.2.15 HDD Manager
Click
, system goes to the HDD manager interface. It is to view and manage HDD information.
Please refer to chapter 4.9.1 HDD manager for detailed information.
4.3.2.16 USB Manager
Click
, system goes to the USB Manager interface. It is to view USB information, backup and update.
Please refer to chapter 4.10.8.1 File backup, chapter 4.10.8.3 Backup log, chapter4.10.8.2 Import/export,
and chapter 4.10.5 Upgrade for detailed information.
4.3.3 Preview Control Interface
Move you mouse to the top center of the video of current channel, you can see system pops up the
preview control interface. See Figure 4-66. If your mouse stays in this area for more than 6 seconds
and has no operation, the control bar automatically hides.
235
Figure 4-66
1) Instant playback
It is to playback the previous 5-60 minutes record of current channel.
Please go to the Main menu->Setting->->System->General to set real-time playback time.
System may pop up a dialogue box if there is no such record in current channel.
2) Digital zoom
It is to zoom in specified zone of current channel. It supports zoom in fu nction of multiple-channel.
Click button
, the button is shown as
.
There are two ways for you to zoom in.
 Drag the mouse to select a zone, you can view an interface show as Figure 4-67.

Figure 4-67
Put the middle button at the center of the zone you want to zoom in, and move the mouse, you
can view an interface shown as in Figure 4-68.
236
Figure 4-68
Right click mouse to cancel zoom and go back to the original interface.
3) Manual record function
It is to back up the video of current channel to the USB device. System cannot backup the vide o of
multiple-channel at the same time.
Click button
, system begins recording. Click it again, system stops recoridng. You can find the record
file on the flash disk.
4)
Manual Snapshot
Click
to snapshot 1-5 times. The snapshot file is saved on the USB device or HDD. You can go to
the Search interface (chapter 4.5) to view.
5) Bidirectional talk
If the connected front-end device supports bidirectional talk function, you can click this button. Click
button
to start bidirectional talk function the icon now is shown as
. Now the rest
bidirectional talk buttons of digital channel becomes null too.
Click
again, you can cancel bidirectional talk and the bidirectional talk buttons of other digital
channels become as
.
6) Registration
Shortcut menu. Click it to go to the registration interface to add/delete remote device or view its
corresponding information. Please refer to chapter4.2.2 for detailed information.
7)
Switch bit streams
Click


to switch the bit stream type of the main stream and sub stream.
M: Main stream.
S: Sub stream. Some series products support two sub streams (S1, S2). Refer to chapter 4.2.5.1
Encode for detailed information.
4.3.4 Right Click Menu
After you logged in the device, right click mouse, you can see the short cut menu. Please see Figure 4-69
or Figure 4-70.
237






Window split mode: You can select window amount and then select channels.
Edit view (Sequence): Change channel display sequence on the preview window.
Customized screen: Set customized screen split mode.
PTZ: Click it to go to PTZ interface.
Fisheye (optional): It is to realize fish eye operation.
Auto focus: It is to set auto focus function. Please make sure the connected network camera
supports this function.
 Color setting: Set video corresponding information.
 Search: Click it to go to Search interface to search and playback a record file.
 Record control: Enable/disable record channel.
 Alarm output: It is to set alarm output mode.
 Camera registration: Search and add a remote device.
 Alarm output: Generate alarm output signal manually.
 Main menu: Go to system main menu interface.
Tips:
Right click mouse to go back to the previous interface.
Figure 4-69
238
Figure 4-70
4.3.5 Edit View (Sequence)
It is to set customized view layout.
Warning
The preview layout restores
menu->Setting->General->Default).
Step 1
default
channel
layout
after
Default
operation.
(Main
On the preview interface, right click mouse and then click Edit view.
Enter edit view interface. See Figure 4-71.
Note
Enter edit view interface, device automatically switches to the max split amount mode.
The channel list on the edit view interface displays the added camera channel number and
channel name.
means camera is online.
means camera is offline.
In case the channel amount has exceeded the device max split amount, the edit view interface
can display the max screen number amount and current screen number. In Figure 4-71, click
or
, switch the video from other channel.
239
Figure 4-71
Step 2
On the edit view interface, drag the channel to the desired window, or drag on the preview
window to switch the position.
Check the channel number at the right bottom corner to view the current channel sequence. See
Figure 4-72.
240
Step 3
Figure 4-72
Click Apply to save current channel sequence.
After you change the channel sequence, click Cancel button or right click mouse, device pops
up the dialogue box. See Figure 4-73.
 Click OK to save current settings.
 Click Cancel to exit without saving the settings.
Figure 4-73
4.3.6 Preview Display Effect Setup
4.3.6.1 Video Color
Here you can set hue, brightness, contrast, saturation, gain, white level, color mode and etc. See
Figure 4-74.
241
Figure 4-74
Please refer to the following sheet for detailed information.
Item
Note
Period
There are two periods in one day. You can set different
sharpness, brightness, and contrast setup for different periods.
Effective Time
Check the box here to enable this function and then set period
time.
Sharpness
Brightness
The value here is to adjust the edge of the video. The value
ranges from 0 to 100. The larger the value is, the clear the edge
is and vice versa. Please note there is noise if the value here is
too high. The default value is 50 and the recommended value
ranges from 40 to 60.
It is to adjust monitor window bright. The value ranges from 0 to
100. The default value is 50.
The larger the number, the bright the video is. When you input
the value here, the bright section and the dark section of the
video will be adjusted accordingly. You can use this function
when the whole video is too dark or too bright. Please note the
video may become hazy if the value is too high. The
recommended value ranges from 40 to 60.
Contrast
It is to adjust monitor window contrast. The value ranges from 0
to 100. The default value is 50.
The larger the number, the higher the contrast is. You can use
this function when the whole video bright is OK but the contrast
is not proper. Please note the video may become hazy if the
value is too low. If this value is too high, the dark section may
lack brightness while the bright section may over exposure .The
recommended value ranges from 40 to 60.
Saturation
It is to adjust monitor window saturation. The value ranges from
242
Item
Note
0 to 100. The default value is 50.
The larger the number, the strong the color is. This value has
no effect on the general brightness of the whole video. The
video color may become too strong if the value is too high. For
the grey part of the video, the distortion may occur if the white
balance is not accurate. Please note the video may not be
attractive if the value is too low. The recommended value
ranges from 40 to 60.
Gain
The gain adjust is to set the gain value. The default value may
vary due to different device models. The smaller the value, the
low the noise. But the brightness is also too low in the dark
environments. It can enhance the video brightness if the value
is high. But the video noise may become too clear.
Color mode
It includes several modes such as standard, color, bright,
gentle. Select a color mode, the sharpness, brightness,
contrast and etc can automatically switch to corresponding
setup.
4.3.6.2 Display
From Main Menu->Setting->System->Display->Display, you can go to the following interface. See Figure
4-75.
Here you can set menu and video preview effect. All you operation here does not affect the record file and
playback effect.
Figure 4-75
243
Now you can set corresponding information.
 Display the intelligent rule(s): Check the box to enable IVS function, system can display IVS rule on
the preview interface. Please note this function is for some series only.
 Resolution: There are five options: 1280×1024 (Default), 1280×720, 1920×1080, 1024×768 and
3840×2160. Please note the system needs to reboot to activate current setup. Please note
3840×2160 is for some series only.
 VGA+HDMI2: It is for dual-screen operation. Please select from the dropdown list according to your
actual situation. Click Apply button, system needs to restart to activate new setup. For example,
32+4 means for VGA, system max supports 32-window split and for HDMI2, system max supports
4-window split. Please note this function is for some series only.
 Color mode: Please select from the dropdown list. It is to set video color mode.
 Transparency: Here is for you to adjust menu transparency. The higher the value is, the better
transparent the menu is.
 Channel name: Here is for you to modify channel name. System max support 25-digit (The value
may vary due to different series). Please note all your modification here only applies to NVR local
end. You need to open web or client end to refresh channel name.
 Time display: You can select to display time or not when system is playback.
 Channel display: You can select to channel name or not when system is playback.
 Image enhance: Check the box; you can optimize the margin of the preview video.
 Original scale: Check the box here to select a corresponding channel; it can restore video original
scale.
 Preview mode: Please select preview mode from the dropdown list. It includes two options:
 General: There is no information on the preview window.
 Human face: System displays human face information on the right pane of the preview window.
 POS Info: Check the box to overlay POS information on the video.
Click OK button to save current setup.
4.3.6.3 TV adjust
Note
Some series product supports TV adjust function. This function is disabled by default.
From Main Menu->Setting->System->Display->TV adjust; you can go to the following interface. See
Figure 4-75. Here you can set margins and brightness.
244
Figure 4-76
4.3.6.4 Preview Tour Parameters
Set preview display mode, channel display sequence and tour setup.
 Set preview display mode: On the preview interface, right click mouse, you can view right-click menu.
Now you can select preview window amount and channel.
 Set channel display mode: On the preview interface, if you want to change channel 1 and channel 16
position, please right click channel 1 video window and then drag to the channel 16 video window,
release button, you can change channel 1 and channel 16 position.
 Tour setup: Here you can set preview window channel display mode and interval. Please follow the
steps listed below.
From Main menu->Setting->System->Display->Tour, you can see an interface shown as in Figure 4-77.
Here you can set tour parameter.
 Enable tour: Check the box here to enable tour function. The general tour supports all types of
window split mode.
 Interval: Input proper interval value here. The value ranges from 1-120 seconds.
 Motion tour type: System support 1/8-window tour. Please note you need to go to the main
menu->Setting->Event->Video detect->Motion detect to enable tour function.
 Alarm tour type: System support 1/8-window tour. Please note you need to go to the main
menu->Setting->Event->Alarm to enable tour function.
 Window split: It is to set window split mode.
245
Figure 4-77
Tips
On the navigation bar, click
/
to enable/disable tour.
Click Save button to save current setup.
4.3.6.5 Customized split
It is to set customized video split mode.
Note
 This function is for some series products. Please refer to the actual product for detailed information.
 Device max supports 5 customized videos.
From Main menu->Setting->System->Display->Custom split, you can see an interface shown as in Figure
4-78.
246
Figure 4-78
Click
and then click
to select basic mode
In regular mode, drag the mouse in the preview frame; you can merge several small windows to one
window so that you can get you desired split mode.
After the setup, the selected window has the red frame. See Figure 4-79.
Figure 4-79
247
Select the merging window, the frame is red; you can click
to cancel the merge to restore regular
mode.
Click Save to exit.
After the setup, you can go to the preview window, right click mouse and then select custom split. See
Figure 4-80.
Figure 4-80
4.3.7 Fisheye (Optional)
Please note this function is for some series only.
4.3.7.1 Fisheye de-warp during preview interface
On the preview interface, select fisheye channel and then right click mouse, you can select fish eye. See
Figure 4-81.
248
Figure 4-81
Now you can see an interface shown as in Figure 4-82. You can set fish eye installation mode and display
mode.
Note:
 For the non-fish eye channel, system pops up dialogue box to remind you it is not a fish eye channel
and does not support de-warp function.
 If system resources are insufficient, system pops up the corresponding dialogue box too.
Figure 4-82
249
There are three installation modes: ceiling mount/wall mount/ground mount. The different
installations modes have different de-warp modes.
Please refer to the following sheet for detailed information.
Installation modes
Icon
Note
360°panorama original view
(Ceiling mount)
1 de-warp window+1 panorama stretching
(Ground mount)
2 panorama stretching view
1 360°panorama view+3 de-warp windows
1 360°panorama view+4 de-warp windows
4 de-warp windows+1 panorama stretching
1 360°panorama view+8 de-warp windows
360°panorama original view
(Wall mount)
Panorama stretching
1 panorama unfolding view+3 de-warp windows
1 panorama unfolding view +4 de warp windows
1 panorama unfolding view +8 de warp windows
Figure 4-83
In Figure 4-83, you can adjust the color pane on the left pane or use your mouse to change the
position of the small images on the right pane to realize fish eye de-warp.
250
4.3.7.2 Fish eye de-warp during playback
On the main menu, click search button.
Select 1-window playback mode and corresponding fish eye channel, click
Right click the
to play.
, you can go to the de-warp playback interface. For detailed information, please
refer to chapter 4.3.7.1.
4.4 PTZ
Note:
Before you control the PTZ, please make sure the PTZ decoder and the NVR network
connection is OK and the corresponding settings are right.
4.4.1 PTZ Settings
Cable Connection
Please follow the procedures below to go on cable connection
 Connect the dome RS485 port to NVR RS485 port.
 Connect dome video output cable to NVR video input port.
 Connect power adapter to the dome.
In the main menu, from Setting->System->PTZ, you can see an interface is shown as in Figure 4-84.
Here you can set the following items:
 Channel: Select the current camera channel.
 PTZ type: There are two types: local/remote. Please select local mode if you are connec t RS485
cable to connect to the Speed dome (PTZ). Please select remote mode if you are connecting to the
network PTZ camera.
 Protocol: Select corresponding PTZ protocol(such as PELCOD)
 Address: Default address is 1.
 Baud rate: Select corresponding baud rate. Default value is 9600.
 Data bit: Select corresponding data bits. Default value is 8.
 Stop bit: Select corresponding stop bits. Default value is 1.
 Parity: There are three options: odd/even/none. Default setup is none.
251
Figure 4-84
If you are connecting to network PTZ, the PTZ type shall be remote. See Figure 4-85.
Figure 4-85
4.4.2 PTZ Control
After completing all the setting please click save button. Right click mouse (click “Fn” Button in the
front panel or click “Fn” key in the remote control). The interface is shown as in Figure 4-86. Please
note you can only go to the PTZ control interface when you are in 1-window display mode.
252
Figure 4-86
The PTZ setup is shown as in See Figure 4-87.
Please note the commend name is grey once device does not support this function.
The PTZ operation is only valid in one-window mode.
Here you can control PTZ direction, speed, zoom, focus, iris, preset, tour, scan, pattern aux function, light
and wiper, rotation and etc.
Speed is to control PTZ movement speed. The value ranges from 1 to 8.The speed 8 is faster than speed
1. You can use the remote control to click the small keyboard to set.
You can click
and
of the zoom, focus and iris to zoom in/out, definition and brightness.
The PTZ rotation supports 8 directions. If you are using direction buttons on the front panel, there are only
four directions: up/down/left/right.
Figure 4-87
In the middle of the eight direction arrows, there is a 3D intelligent positioning key. See Figure 4-88.
Please make sure your protocol supports this function and you need to use mouse to control.
Click this key, system goes back to the single screen mode. Drag the mouse in the screen to adjust
section size. The dragged zone supports 4X to 16X speeds. It can realize PTZ automatically. The smaller
253
zone you dragged, the higher the speed.
Figure 4-88
Name
Function
key
function
Zoom
Near
Focus
Near
Iris
close
In Figure 4-87, click
Shortcut
key
Function
key
function
Far
Shortcut
key

│
Far
►│

Open

to open the menu, you can set preset, tour, pattern, scan and etc. See
Figure 4-89.
Figure 4-89
Please refer to the following sheet for detailed information.
Please note the above interface may vary due to different protocols. The button is grey and cannot be
selected once the current function is null.
Right click mouse or click the ESC button at the front panel to go back to the Figure 4-87.
Icon
Function
Icon
Function
Preset
Flip
Tour
Reset
Pattern
Aux
Scan
Aux
on-off
button
Rotate
Go to menu
4.4.2.1 PTZ Function Setup
254
Click
, you can go to the following interface to set preset, tour, pattern, and scan. See Figure 4-90.
Figure 4-90
Preset Setup
In Figure 4-90, click preset button and use eight direction arrows to adjust camera to the proper position.
The interface is shown as in Figure 4-91.
Click Set button and then input preset number.
Click Set button to save current preset.
Figure 4-91
Tour Setup
In Figure 4-90, click tour button.
Input tour value and preset No. Click Add preset button to add current preset to the tour. See Figure 4-92.
Tips
Repeat the above steps to add more presets to the tour. Click Del preset button to remove it from the tour.
Please note some protocols do not support delete preset function.
255
Figure 4-92
Pattern Setup
In Figure 4-90, click Pattern button and input pattern number.
Click Begin button to start direction operation. Or you can go back to Figure 4-87 to operate
zoom/focus/iris/direction operation.
In Figure 4-90, click End button.
Figure 4-93
Scan Setup
In Figure 4-90, click Scan button.
Use direction buttons to set camera left limit and then click Left button.
Use direction buttons to set camera right limit and then click Right button. Now the scan setup process is
complete.
256
Figure 4-94
4.4.2.2 Call PTZ Function
Call Preset
In Figure 4-89, input preset value and then click
to call a preset. Click
again to stop call.
Call Pattern
In Figure 4-89, input pattern value and then click
call.
to call a pattern. Click
again to stop
Call Tour
In Figure 4-89, input tour value and then click
to call a tour. Click again
to stop call.
Call Scan
In Figure 4-89, input Scan value and then click
to call a tour. Click again
to stop call.
Rotate
In Figure 4-89, click
to enable the camera to rotate.
System supports preset, tour, pattern, scan, rotate, light and etc function.
Note:
 Preset, tour and pattern all need the value to be the control parameters. You can define it as yo u
require.
 You need to refer to your camera user’s manual for Aux definition. In some cases, it can be used for
special process.
Aux
Click
, system goes to the following interface. The options here are defined by the protocol. The aux
number is corresponding to the aux on-off button of the decoder. See Figure 4-95.
257
Figure 4-95
4.5 Record File
Device adopts 24-hour continuous record by default. It supports customized record period and record
type. Refer to chapter 4.1.4.6 Schedule for detailed information.
4.6 Playback and Search
4.6.1 Instant Playback
Please refer to chapter 4.3.2 for real-time playback information.
4.6.2 Search Interface
From Main menu->Search, or on the preview interface right click mouse and then select search item, you
can go to the following interface. See Figure 4-96 or Figure 4-97.
Figure 4-96
258
Figure 4-97
Please refer to the following sheet for more information.
SN
1
Name
Display
window
Function


Here is to display the searched picture or file.
Support 1/4/9/16-window playback. (It depends on the product channel
amount).
Search
type
 Here you can select to search the picture or the recorded file.
 You can select to play from the read-write HDD, from peripheral device or from
redundancy HDD.
 Before you select to play from the peripheral device, please connect the
corresponding peripheral device. You can view all record files of the root directory
of the peripheral device. Click the Browse button; you can select the file you want to
play.
Important
 Redundancy HDD does not support picture backup function, but it
supports picture playback function. You can select to play from redundancy
HDD if there are pictures on the redundancy HDD.
3
Calendar
 The blue highlighted date means there is picture or file. Otherwise, there is no
picture or file.
 In any play mode, click the date you want to see, you can see the
corresponding record file trace in the time bar.
4
Playback
mode
and
2


Playback mode:1/4/9/16. (It may vary due to different series.)
In 1-window playback mode: you can select 1-X channels (X depends on the
product channel amount).
259
5
6
7
8
channel
selection
pane.

Card
number
search
The card number search interface is shown as below. Here you can view card
number/field setup bar. You can implement advanced search. Current series
product supports this function.
Face list
Mark file
list button
File
list
switch
button
In 4-window playback mode: you can select 4 channels according to your
requirement.
 In 9-window playback mode, you can switch between 1-8, 9-16 and etc
channels.
 In 16-window playback mode, you can switch between1-16, 17-32 and etc
channels.
 The time bar will change once you modify the playback mode or the channel
option.
You can search when it is in 1-channel playback mode. Click it, system can filter all
human faces and generate human face list. Double click the file; system begins
playback the record or image of the corresponding human face.
Click it to go to mark file list interface. You can view all mark information of current
channel by time. Please refer to chapter 4.6.4 for detailed information.
Please note only the product of this icon supports mark function.
 Double click it, you can view the picture/record file list of current day.
 The file list is to display the first channel of the record file.
 The system can display max 128 files in one time. Use the │and │ or the
mouse to view the file. Select one item, and then double click the mouse or click the
ENTER button to playback.
 You can input the period in the following interface to begin accurate search.
 File type:R—regular record; A—external alarm record;M—Motion detect
record.

Lock file. Click the file you want to lock and click the button
to lock. The
file you locked will not be overwritten.

Search locked file: Click the button
to view the locked file.
Play/Pause
Return:
buttonways ,for
system
back
to the calendar and channel setup
ThereClick
are three
you togoes
begin
playback.
 The play button
interface.
►/
 Double click the valid period of the time bar.
Please note:
the item
in the file list.
 Forthe Double
file that click
is writing
or overwriting,
it cannot be locked.
In slow play mode, click it to switch between play/pause.

9
Playback
control
pane.
■
Stop

Backward play
In normal play mode, left click the button, the file begins backward play.
Click it again to pause current play.
In backward play mode, click ►/ to restore normal play.
│/
│
In playback mode, click it to play the next or the previous section. You can
click continuously when you are watching the files from the same channel.
In normal play mode, when you pause current play, you can click │ and
260
│ to begin frame by frame playback.
In frame by frame playback mode, click ►/ to restore normal playback.
►

Slow play
In playback mode, click it to realize various slow play modes such as slow
play 1, slow play 2, and etc.
Fast forward
In playback mode, click to realize various fast play modes such as fast
play 1,fast play 2 and etc.
Note: The actual play speed has relationship with the software version.
Smart search
The volume of the playback
Click the snapshot button in the full-screen mode, the system can snapshot
1 picture.
System supports custom snap picture saved path. Please connect the
peripheral device first, click snap button on the full-screen mode, you can
select or create path. Click Start button, the snapshot picture can be saved
to the specified path.
Mark button.
Please note this function is for some series product only. Please make sure
there is a mark button in the playback control pane.
You can refer to chapter 4.6.4 for detailed information.
In 1-channel playback mode, click it to enable/disable display IVS rule
information on the video.
10
Time bar
 It is to display the record type and its period in current search criteria.
 In 4-window playback mode, there are corresponding four time bars. In other
playback mode, there is only one time bar.
 Use the mouse to click one point of the color zone in the time bar, system
begins playback.
 The time bar is beginning with 0 o'clock when you are setting the configuration.
The time bar zooms in the period of the current playback time when you are playing
the file.
 The green color stands for the regular record file. The red color stands for the
external alarm record file. The yellow stands for the motion detect record file.
●The option includes:
11
Time bar
unit
12
Backup
、
、
和
,. The smaller the unit,
the larger the zoom rate. You can accurately set the time in the time bar to playback
the record.
 The time bar is beginning with 0 o'clock when you are setting the configuration.
The time bar zooms in the period of the current playback time when you are playing
the file.

Select the file(s) you want to backup from the file list. You can check from the
list. Then click the backup button, now you can see the backup menu. System
261



supports customized path setup. After select or create new folder, click the
Start button to begin the backup operation. The record file(s) will be saved in
the specified folder.
Check the file again you can cancel current selection. System max supports to
display 32 files from one channel.
After you clip on record file, click Backup button you can save it.
For one device, if there is a backup in process, you cannot start a new backup
operation.
It is to edit the file.
13
Clip

Please click

Select clip start time on the time bar and then Click
to start clip.

Select clip stop time on the time bar and then click
to stop clip.

Click
to play the file you want to edit.
, system pops up file backup dialogue box for you to save.
Please note:
 Clip function is for one-channel mode/multiple-channel mode.
 System max supports 1024 files backup at the same time.
 You cannot operate clip operation if there is any file has been checked in
the file list.
14
Record
type
In any play mode, the time bar will change once you modify the search type.
Other Functions


15
Motion
detection
search



16
Other
channel
synchroni
zation
switch to
play
when
playback
When system is playing, you can select a zone in the window to begin motion
detection search. Click the motion detect button to begin play.
Once the motion detect play has begun, click button again will terminate
current motion detect file play.
There is no motion detect zone by default.
If you select to play other file in the file list, system switches to motion detect
play of other file.
During the motion detect play process, you cannot implement operations such
as change time bar, begin backward playback or frame by frame playback.
When playing the file, click the number button, system can switch to the same
period of the corresponding channel to play.
262
17
Digital
zoom
When the system is in full-screen playback mode, left click the mouse in the
screen. Drag your mouse in the screen to select a section and then left click
mouse to realize digital zoom. You can right click mouse to exit.
18
Manually
switch
channel
when
playback
During the file playback process, you can switch to other channel via the
dropdown list or rolling the mouse.
This function is null if there is no record file or system is in smart search process.
Note:
All the operations here (such as playback speed, channel, time and progress) have relationship with
hardware version. Some series NVRs do not support some functions or playback speeds.
4.6.2.1 Playback Control
The playback control interface is shown as below. See Figure 2-44.
Figure 4-98
Please refer to the following sheet for more information.
Icon
、
Function
Play/Pause
In slow play mode, click it to switch between play/pause.
Backward play
 In normal play mode, left click the button, the file begins backward
play. Click it again to pause current play.

In backward play mode, click
or
to restore normal play.
Display previous frame/next frame.

When pause the normal playback file, click
or
to
playback frame by frame.
、

In frame by frame playback mode, click
or
to resume
normal playback mode.
Slow play
In playback mode, click it to realize various slow play modes such as
slow play 1, slow play 2, and etc.
Fast forward
In playback mode, click to realize various fast play modes such as
fast play 1,fast play 2 and etc.
Adjust the volume of the playback
Smart search .
You can refer to chapter 4.6.3 for detailed information.
263
Icon
Function
Click the snapshot button in the full-screen mode, the system can
snapshot 1 picture.
System supports custom snap picture saved path. Please connect the
peripheral device first, click snap button on the full-screen mode, you
can select or create path. Click Start button, the snapshot picture can
be saved to the specified path.
Mark button.
Please note this function is for some series product only. Please make
sure there is a mark button in the playback control pane.
You can refer to chapter 4.6.4 for detailed information.
Display/hide POS information.
In 1-channel playback mode, you can click it to display/hide POS
information on the video.
Note
This function is for some series only.
In 1-channel playback mode, click it to enable/disable display IVS rule
information on the video.
4.6.2.2 Clip
This function allows you to clip some footages to a new file and then save to the USB device. See Figure
2-46. Please follow the steps listed below.
1)
Select a record first and then click
to playback.
2)
Select a time at the time bar and then click
to start clip,
3)
Select a time at the time bar and then click
to stop clip,
4)
Click
, system pops up dialogue box to save the clip file.
Figure 4-99
Note
 Clip function is for one-channel/multiple-channel.
 Max save 1024 files at the same time.
 This function is not for the file already checked in the file list.
4.6.2.3 Record Backup
This function is to backup files you checked in the file list, or the file you just clip.
Click
, enter the following interface. See Figure 4-100.
264
Figure 4-100
Click Backup to begin the process.
4.6.3 Smart Search Playback
Note
This function is for some series product only.
During playback process, it can analyze the motion detect zone in the scene and give the analysis
result.
This function is for channel that already enabled
menu->Setting->Event->Video detect->Motion detect).
Please follow the steps listed below.
1)
Select a channel to playback video and then click
motion
detect
function
(main
. You can view the grids on the playback
video.
Note
 This function is for one-channel playback mode.
 If you are in multiple-channel playback mode, double click a channel first to switch to one-channel
playback mode.
2) Left click mouse and then drag to select smart search zones(22*18(PAL)
,22*15(NTSC)).
3)
Click
to go to smart search and playback. System is going to playback all motion detect
record footages.
4)
Click
again to stop smart search function.
265
4.6.4 Mark Playback
Please make sure your purchased device support this function. You can use this function only if
you can see the mark playback icon on the Search interface (Figure 4-96 or Figure 4-97).
When you are playback record, you can mark the record when there is important information. After
playback, you can use time or the mark key words to search corresponding record and then play. It is very
easy for you to get the important video information.
 Add Mark
When system is playback, click Mark button
, you can go to the following interface. See Figure 4-101.
Figure 4-101

Playback Mark
During 1-window playback mode, click mark file list button
in Figure 4-96 or Figure 4-97, you can go
to mark file list interface. Double click one mark file, you can begin playback from the mark time.
 Play before mark time
Here you can set to begin playback from previous N seconds of the mark time.
Note
Usually, system can playbacks previous N seconds record if there is such kind of record file. Otherwise,
system playbacks from the previous X seconds when there is such as kind of record.

Mark Manager
Click the mark manager button
on the Search interface (Figure 4-96 or Figure 4-97); you can go
to Mark Manager interface. See Figure 4-102. System can manage all the record mark information of
current channel by default. You can view all mark information of current channel by time.
266
Figure 4-102
 Modify
Double click one mark information item, you can see system pops up a dialogue box for you to change
mark information. You can only change mark name here.
 Delete
Here you can check the mark information item you want to delete and then click Delete button, you can
remove one mark item. .
Note
 After you go to the mark management interface, system needs to pause current playback. System
resume playback after you exit mark management interface.
 If the mark file you want to playback has been removed, system begins playback from the first file in
the list.
4.6.5 Playback Image
Here you can search and play the image. Please follow the steps listed below.
1) From main menu->Search, or on the preview window right click mouse and then click Search, you
can go to the search interface.
2) At the top right corner, select image and then input playback interval.
3)
Select date and channel, click
to play.
4.6.6 Splice Playback
For the large record file, you can use splice playback function to play the same file in several sections at
the same time. It is very convenient for you to find the video footages you desire.
On the main menu, click Search button, or right click mouse and then select Search. You can go to Figure
4-96 or Figure 4-97
On the right pane, check the box to enable splice playback function, and then set channel, date, split
mode. The splice playback interface is shown as below. Each section has a small triangle; you can adjust
it
to
set
time.
See
Figure
4-103.
267
Figure 4-103
Note
Select split mode, so that the record can be spliced in several sections.
Select splice file.
 Click Playback, system playbacks from the first of current date by default.
 Click time bar, system playbacks from the time you click.

Click
, you can select on the file list.
Note



The splice playback is for 1-window playback mode.
System supports 1/4/8/16-split mode. Slight different may be found here. The 4-channel series
product supports 4-split mode. The 8-channel series product support 8-split mode. The 16-channel
or higher series product supports 16-split mode.
The min period of each section is 5 minutes. For the record is less than 20 minutes, if you select
4-split mode (or more than 4-split mode), system can auto adjust so that the each section period is 5
minutes. In this situation, some channel may have no video.
4.6.7 Smart Playback
It is to search and playback the IVS file, human face file and plate recognition record.
Note


There are two types to realize intelligent analytics function.
Smart network camera supports intelligent functions: Some smart camera supports the intelligent
functions. For NVR, it just displays the intelligent alarm information from the smart network camera
and set or playback the record file.
 NVR supports intelligent functions: The connected network camera does not support intelligent video
analytics function. The NVR supports the analytics function.
 This function is to playback the intelligent record file of the smart camera.
4.6.7.1 IVS File
It is to search and playback the IVS record file.
Step 1 From main menu->Operation->Smart Play.
Enter the smart play interface. See Figure 4-104.
268
Figure 4-104
Step 2
Step 3
Select detection type as behavior analytics.
Select a channel.
Enter the following interface. See Figure 4-105.
Note
The IVS function is for one-channel mode only.
269
Figure 4-105
Step 4
Step 5
Step 6
Select a channel number and then click OK.
Set detection type as IVS and then set start time and end time.
Click Historic Analysis.
Device displays the corresponding image. See Figure 4-106.
Figure 4-106
Step 7
Click the image; you can view the record file.
270

Select a file and then click

Select a file and then click
, you can save current file to peripheral storage device.
, you can lock current file in case it will be overwritten in the
future

Select a file and then click
, you can mark the time of the detected event.
4.6.7.2 Search Human Face (Optional)
It is to search and playback human face record.
Step 1
Step 2
From main menu->Operation->Smart Play.
Enter the smart play interface.
Select detection type as face detection.
Enter human face detection and playback interface. See Figure 4-107.
Figure 4-107
Step 3
Step 4
Set channel, start time and end time.
Click Historic analysis.
Device displays the searched human face image. See Figure 4-108.
Note
The following human face has been modified for privacy reason. The actual snapshot image has
high definition.
271
Step 5
Figure 4-108
Click the image; you can view the record file.

Select a file and then click

Select a file and then click
, you can save current file to peripheral storage device.
, you can lock current file in case it will be overwritten in the
future

Select a file and then click
, you can mark the time of the detected event.
4.6.7.3 Plate recognition
It is to search and playback the record file containing the plate number.
Step 1 From main menu->Operation->Smart Play.
Enter the smart play interface. See Figure 4-109.
272
Figure 4-109
Step 2
Set plate number, channel number, start time, end time.
Note
Device supports fuzzy plate number search function.
Device searches all plate numbers by default if you do not input plate number information.
The plate number search and playback function is for one-channel mode only.
Step 3 Click Historic Analytics.
Device displays the corresponding image.
Step 4 Click the image; you can view the record file.

Select a file and then click

Select a file and then click
, you can save current file to peripheral storage device.
, you can lock current file in case it will be overwritten in the
future

Select a file and then click
, you can mark the time of the detected event.
4.6.8 File List
Click
, system displays file list. It displays the first channel of the record. See Figure 4-110.
273
Figure 4-110

Check a file name, double click file or click


Input accurate time at the top column, you can search records of current day.
System max displays 128 record files in one list.

Click
to play.
to go back to the calendar/channel selection interface.
Lock or Unlock File
In Figure 2-47, select a file first and then click
. You can lock it in case it is overwritten in the future.
Note
The file is writing or is overwriting cannot be locked.
274
Click
you can view the locked file. See Figure 4-111.
Figure 4-111
Select a file in the above figure and then click Unlock, you can unlock it.
4.6.9 Other Aux Functions
4.6.9.1 Digital Zoom
In 1-window playback mode, left click mouse to select any zone on the screen, you can zoom in
current zone. Right click mouse to exit.
4.6.9.2 Switch Channel
During playback mode, select from the dropdown list to switch playback channel. This function is not
for the channel of no record. The smart search channel does not support this function either.
4.7
Event Manager
4.7.1 Video Detect
In the main menu, from Setting to Detect, you can see motion detect interface. See Figure
4-112.There are four detection types: motion detection, video loss, tampering and scene changing.
4.7.1.1 Motion Detect
After analysis video, system can generate a motion detect alarm when the detected moving signal
reached the sensitivity you set here.
Detection menu is shown as below. See Figure 4-112.
 Event type: From the dropdown list you can select motion detection type.
 Channel: Select a channel from the dropdown list to set motion detect function.
 Enable: Check the box here to enable motion detect function.
 Region: Click select button, the interface is shown as in Figure 4-113. Here you can set motion
detection zone. There are four zones for you to set. Please select a zone first and then left drag the
mouse to select a zone. The corresponding color zone displays different detection zone. You can
275




click Fn button to switch between the arm mode and disarm mode. In arm mode, you can click the
direction buttons to move the green rectangle to set the motion detection zone. After you completed
the setup, please click ENTER button to exit current setup. Do remember click save button to save
current setup. If you click ESC button to exit the region setup interface system will not save your
zone setup.
Sensitivity: System supports 6 levels. The sixth level has the highest sensitivity.
Anti-dither: Here you can set anti-dither time. The value ranges from 5 to 600s. The anti-dither time
refers to the alarm signal lasts time. It can be seem as the alarm signal activation stays such as the
buzzer, tour, PTZ activation, snapshot, channel record. The stay time here does not include the latch
time. During the alarm process, the alarm signal can begin an anti-dither time if system detects the
local alarm again. The screen prompt, alarm upload, email and etc will not be activated. For example,
if you set the anti-dither time as 10 second, you can see the each activation may last 10s if the local
alarm is activated. During the process, if system detects another local alarm signal at the fifth
second, the buzzer, tour, PTZ activation, snapshot, record channel will begin another 10s while the
screen prompt, alarm upload, email will not be activated again. After 10s, if system detects another
alarm signal, it can generate an alarm since the anti-dither time is out.
Period: Click set button, you can see an interface is shown as in Figure 4-115. Here you can set
motion detect period. System only enables motion detect operation in the specified periods. It is not
for video loss or the tampering. There are two ways for you to set periods. Please note system only
supports 6 periods in one day.
In Figure 4-115, Select icon
the icon is shown as

. Click
In Figure 4-115. Click button
of several dates, all checked items can be edited together. Now
to delete a record type from one period.
after one date or a holiday, you can see an interface shown as in
Figure 4-116. There are four record types: regular, motion detection (MD), Alarm, MD & alarm.



Alarm output: when an alarm occurs, system enables peripheral alarm devices.
Latch: when motion detection complete, system auto delays detecting for a specified time. The value
ranges from 1-300(Unit: second)
Show message: System can pop up a message to alarm you in the local host screen if you enabled
this function.
Alarm upload: System can upload the alarm signal to the network (including alarm center) if you
enabled current function.
Send email: System can send out email to alert you when an alarm occurs.
Record channel: System auto activates motion detection channel(s) to record once an alarm occurs.
Please make sure you have set MD record in Schedule interface(Main Menu->Setting->Schedule)
and schedule record in manual record interface(Main Menu->Advanced->Manual Record)
PTZ activation: Here you can set PTZ movement when an alarm occurs. Such as go to preset, tour
&pattern when there is an alarm. Click “select” button, you can see an interface is shown as in Figure
4-114 .
Record Delay: System can delay the record for specified time after alarm ended. The value ranges
from 10s to 300s.
Tour: Here you can enable tour function when alarm occurs. System one-window tour.

Snapshot: You can enable this function to snapshot image when a motion detect alarm occurs.





X

276


Video matrix Check the box here to enable this function. When an alarm occurs, SPOT OUT port
displays device video output. It displays video (1-window tour) from alarm activation channel you
select at the Record channel item.
Buzzer: Highlight the icon to enable this function. The buzzer beeps when alarm occurs.
Please highlight icon
to select the corresponding function. After all the setups please click save
button, system goes back to the previous menu.
Note:
In motion detection mode, you cannot use copy/paste to set channel setup since the video in each
channel may not be the same.
In Figure 4-113, you can left click mouse and then drag it to set a region for motion detection. Click Fn to
switch between arm/withdraw motion detection. After setting, click enter button to exit.
Figure 4-112
Figure 4-113
277
Figure 4-114
Figure 4-115
278
Figure 4-116
Motion detect here only has relationship with the sensitivity and region setup. It has no relationship
with other setups.
4.7.1.2 Tampering
When someone viciously masks the lens, or the output video is in one-color due to the environments
light change, the system can alert you to guarantee video continuity. Tampering interface is shown as
in Figure 4-117. You can enable “Alarm output “or “Show message” function when tampering alarm
occurs.
 Sensitivity: The value ranges from 1 to 6. It mainly concerns the brightness. The level 6 has the
higher sensitivity than level 1. The default setup is 3.
Tips:
You can enable preset/tour/pattern activation operation when video loss occurs.
Please refer to chapter 4.7.1.1 motion detection for detailed information.
Note:
 In Detect interface, copy/paste function is only valid for the same type, which means you cannot
copy a channel setup in video loss mode to tampering mode.
 About Default function. Since detection channel and detection type may not be the same, s ystem
can only restore default setup of current detect type. For example, if you click Default button at
the tampering interface, you can only restore default tampering setup. It is null for other detect
types.
 System only enables tampering function during the period you set here. It is null for motion detect
or video loss type.
279
Figure 4-117
4.7.1.3 Video Loss
In Figure 4-112, select video loss from the type list. You can see the interface is shown as in Figure
4-118. This function allows you to be informed when video loss phenomenon occurred. You can
enable alarm output channel and then enable show message function.
You can refer to chapter 4.7.1.1Motion detect for detailed information.
Tips:
You can enable preset/tour/pattern activation operation when video loss occurs.
280
Figure 4-118
4.7.1.1 Scene Changing
When the detected scene has changed, system can generate an alarm.
From main menu->Setting->Event->Video detect->Scene change, the interface is shown as in Figure
4-119.
Please refer to chapter 4.7.1.1Motion detect for detailed information.
281
Figure 4-119
4.7.2 Smart Plan
The smart plan is for the smart network camera. If you do not set a rule here, you cannot use the
intelligent functions in IVS (Chapter 4.7.3), Face detection (Chapter 4.7.5) and People counting (Chapter
4.7.6) when you are connecting to a smart network camera.
There are two types to realize intelligent analytics function.
Note


Smart network camera supports intelligent functions: Some smart camera supports the intelligent
functions. For NVR, it just displays the intelligent alarm information from the smart network camera
and set or playback the record file.
NVR supports intelligent functions: The connected network camera does not support intelligent video
analytics function. The NVR supports the analytics function.
In this interface, you can quickly add an intelligent rule for one preset. The intelligent rule includes human
face detection, behavior analytics and people counting.
From main menu->Setting->Event->Smart plan, the interface is shown as below. See Figure 4-120.
282
Figure 4-120
Please select a channel number and a preset. Click Add.
The preset is now on the list. See Figure 4-121.
Note
Some smart camera does not need to add the preset. Please refer to the actual product for detailed
information.
283
Figure 4-121
Select a smart plant from the dropdown list and then click the corresponding intelligent plan icon. See
Figure 4-121.
Note

The NVR supports general behavior analytics (IVS), human face detection, heat map, and people
counting. Different network camera supports different smart plans. Please refer to the actual product
for detailed information.
 The general behavior analytics (IVS) and human face detection function cannot be valid at the same
time. For example, when add the IVS plan to the preset 1, the human face detection icon becomes
grey.
Click OK to complete the setup.
4.7.3 IVS (Optional)
Once the object state has reached the threshold, NVR can trigger an intelligent alarm.
Note

This function is for some series product only. Please refer to the actual product for detailed
information.
 The IVS function and the human face detection function cannot be valid at the same time.
The IVS function environment shall meet the following requirements:
 The object total size shall not be more than 10% of the whole video.
 The object size on the video shall not be more than 10pixels*10 pixels. The abandoned object size
284




shall be more than 15pixels*15 pixels (CIF resolution). The object width shall not be more than 1/3 of
the video height and width. The recommended height is 10% of the video.
The object and the background brightness different shall be more than 10 grey levels.
The object shall remain on the video for more than 2 seconds. The moving distance is larger than its
own width and shall not be smaller than 15pixels (CIF resolution).
The surveillance environment shall not be too complicated. The IVS function is not suitable for the
environment of too many objects or the changing light.
The surveillance environment shall not contain glasses, reflection light from the ground, and water.
Free of tree branches, shadow, mosquito and bugs. Do not use the IVS function in the backlight
environment, avoid direct sunlight.
From main menu->Setting->Event, you can go to the IVS interface.
4.7.4 IVS (Behavior Analytics) (Optional)
From main menu->Setting->Event->Behavior Analytics, you can go to the behavior analytics interface.
Here you can set general behavior analytics rule. System can generate an alarm as the mode you
previously set once there is any object violates the rule. See Figure 4-122.
Figure 4-122
Select a channel from the dropdown list.
Click Add button to add a rule and then select a rule type from the dropdown list.
Set corresponding parameters.
Click Apply button to complete the setup.
4.7.4.1 Tripwire (Optional)
System generates an alarm once there is any object crossing the tripwire in the specified direction.
 The tripwire supports customized setup. It can be a straight line or a curve.
285
 Support one-direction or dual-direction detection.
 Support several tripwires at the same scene suitable for complicated environment.
 Support object size filter.
From main menu->Setting->Event->Behavior analytics, the interface is shown as below. See Figure
4-123.
Figure 4-123
Click Draw button
to draw the tripwire. See Figure 4-124.
286
Figure 4-124
Select direction, and then input customized rule name.
 Preset: Select a preset you want to use behavior analytics.
 Name: Input customized rule name.
 Direction (A→B/B→A/A↔B): System can generate an alarm once there is any object crossing in the
specified direction.

Target filter: Click
, you can set filter object size. Each rule can set two sizes (min size/max size).
Once the object is smaller than the min size or larger than the max size, there is no alarm. Please
make sure the max size is larger than the min size.
Now you can draw a rule. Left click mouse to draw a tripwire. The tripwire can be a direct line, curve or
polygon. Right click mouse to complete.
Tips
Click
Click
to delete the corresponding rule.
, you can see the following interface. See Figure 4-125.
You can refer to the following information to set other parameters.
 Channel: Select a channel from the dropdown list to set tripwire function.
 Enable: Check the box here to enable tripwire function.
 Rule: input customized rule name here.
 Period: Click set button, you can see an interface is shown as in Figure 4-115. Here you can set
tripwire period. System only enables tripwire operation in the specified periods. There are two ways
for you to set periods. Please note system only supports 6 periods in one day.
287

In Figure 4-115, Select icon
Now the icon is shown as

In Figure 4-115. Click button
of several dates, all checked items can be edited together.
. Click
to delete a record type from one period.
after one date or a holiday, you can see an interface shown
as in Figure 4-116.







Alarm output: when an alarm occurs, system enables peripheral alarm devices.
Latch: when tripwire complete, system auto delays detecting for a specified time. The value ranges
from 1-300(Unit: second)
Show message: System can pop up a message to alarm you in the local host screen if you enabled
this function.
Alarm upload: System can upload the alarm signal to the network (including alarm center) if you
enabled current function.
Send email: System can send out email to alert you when an alarm occurs.
Record channel: System auto activates tripwire channel(s) to record once an alarm occurs. Please
make sure you have set intelligent record in Schedule interface(Main Menu->Setting->Schedule)
and schedule record in manual record interface(Main Menu->Advanced->Manual Record)
PTZ activation: Here you can set PTZ movement when an alarm occurs. Such as go to preset, tour
&pattern when there is an alarm. Click “select” button, you can see an interface is shown as in
Figure 4-114 .
Record Delay: System can delay the record for specified time after alarm ended. The value ranges
from 10s to 300s.
Tour: Here you can enable tour function when an alarm occurs. System one-window tour.
X




Snapshot: You can enable this function to snapshot image when a motion detect alarm occurs.
Buzzer: Highlight the icon to enable this function. The buzzer beeps when an alarm occurs.
Figure 4-125
288
Figure 4-126
Figure 4-127
289
Figure 4-128
After you set the corresponding parameters, click OK button in Figure 4-125., and then click the Apply
button in Figure 4-123 to complete the setup.
4.7.4.2 Intrusion (Cross warning zone) (Optional)
System generates an alarm once there is any object entering or exiting the zone in the specified direction.
From main menu->Setting->Event->Behavior analytics, click Add button and then select type as intrusion,
the interface is shown as below. See Figure 4-129.
 System supports customized area shape and amount.
 Support enter/leave/both detection.
 Can detect the moving object operation in the specified zone, customized trigger amount and staying
time.
 Support objects filter function.
290
Figure 4-129
Click draw button
to draw the zone. See Figure 4-130.
291
Figure 4-130
Select direction, and then input customized rule name.
 Preset: Select a preset you want to use behavior analytics.
 Name: Input customized rule name.
 Direction (A→B/B→A/A↔B): System can generate an alarm once there is any object crossing in the
specified direction.

Target filter: Click
, you can set filter object size. Each rule can set two sizes (min size/max size).
Once the object is smaller than the min size or larger than the max size, there is no alarm. Please
make sure the max size is larger than the min size.
Now you can draw a rule. Left click mouse to draw a warning zone. Right click mouse to complete the
setup.
Tips
Click
to delete the corresponding rule.
Click
, you can refer to chapter 4.7.4.1 to set other parameters.
Click Apply to complete the setup.
4.7.4.3 Abandoned Object Detect (Optional)
System generates an alarm when there is abandoned object in the specified zone.
From main menu->Setting->Event->Behavior analytics, select the type as abandoned object, the object
interface is shown as below. See Figure 4-131.
292



System supports customized area shape and amount.
Support duration setup.
Support objects filter function.
Figure 4-131
Click draw button
to draw the zone. See Figure 4-132.
293
Figure 4-132



Preset: Select a preset you want to use behavior analytics.
Name: Input customized rule name.
Duration: System can generate an alarm once the object is in the zone for the specified period.

Target filter: Click
, you can set filter object size. Each rule can set two sizes (min size/max size).
Once the object is smaller than the min size or larger than the max size, there is no alarm. Please
make sure the max size is larger than the min size.
Now you can draw a rule. Left click mouse to draw a zone, until you draw a rectangle, you can right click
mouse.
Tips
Click
to delete the corresponding rule.
Click
, you can refer to the chapter 4.7.4.1 to set other parameters.
Click Apply to complete the setup.
4.7.4.4 Missing Object Detection (Optional)
System generates an alarm when there is missing object in the specified zone.
From main menu->Setting->Event->Behavior analytics, select the type as abandoned object, the object
interface is shown as below. See Figure 4-133.
 System supports customized area shape and amount.
 Support duration setup.
 Support objects filter function.
294
Figure 4-133
Click Draw button
to draw a zone. See Figure 4-134.
Figure 4-134
295



Preset: Select a preset you want to use behavior analytics.
Name: Input customized rule name.
Duration: System can generate an alarm once the object in the zone is missing for the specified
period.

Target filter: Click
, you can set filter object size. Each rule can set two sizes (min size/max size).
Once the object is smaller than the min size or larger than the max size, there is no alarm. Please
make sure the max size is larger than the min size.
Now you can draw a rule. Left click mouse to draw a zone, until you draw a rectangle, you can right click
mouse.
Tips
Click
to delete the corresponding rule.
Click
, you can refer to the chapter 4.7.4.1 to set other parameters.
Click Apply to complete the setup.
4.7.4.5 Loitering Detection (Optional)
System can generate an alarm once the object is staying in the specified zone longer than the threshold.
From main menu->Setting->Event->Behavior analytics, select the type as loitering, the object interface is
shown as below. See Figure 4-135.
 System supports customized area shape and amount.
 Support duration setup.
 Support objects filter function.
Figure 4-135
296
Click draw button
to draw the zone. See Figure 4-136.
Figure 4-136



Preset: Select a preset you want to use behavior analytics.
Name: Input customized rule name.
Duration: System can generate an alarm once the object is in the zone for the specified period.

Target filter: Click
, you can set filter object size. Each rule can set two sizes (min size/max size).
Once the object is smaller than the min size or larger than the max size, there is no alarm. Please
make sure the max size is larger than the min size.
Now you can draw a rule. Left click mouse to draw a zone, until you draw a rectangle, you can right click
mouse.
Tips
Click
to delete the corresponding rule.
Click
, you can refer to the chapter 4.7.4.1 to set other parameters.
Click Apply to complete the setup.
4.7.4.6 Crowd Gathering Detection (Optional)
System can generate an alarm once the people amount gathering in the specified zone is larger than the
threshold.
From main menu->Setting->Event->Behavior analytics, select the type as crowd gathering detect, the
interface is shown as below. See Figure 4-137.
297




Customized zone and amount setup.
Duration setup.
Sensitivity setup.
Min gathering zone setup.
Figure 4-137
Click draw button
to draw the zone. See Figure 4-138.
298
Figure 4-138




Preset: Select a preset you want to use behavior analytics.
Name: Input customized rule name.
Duration: System can generate an alarm once the object is in the zone for the specified period.
Sensitivity: It is to set alarm sensitivity. The value ranges from 1 to 10.The default setup is 5.

Target filter: Click
, you can set filter object size. Each rule can set two sizes (min size/max size).
Once the object is smaller than the min size or larger than the max size, there is no alarm. Please
make sure the max size is larger than the min size.
Now you can draw a rule. Left click mouse to draw a zone, until you draw a rectangle, you can right click
mouse.
Tips
Click
to delete the corresponding rule.
Click
, you can refer to the chapter 4.7.4.1 to set other parameters.
Click Apply to complete the setup.
4.7.4.7 Fast moving (Optional)
It is to detect the fast moving object in the specified zone.
From main menu->Setting->Event->Behavior analytics, select the type as fast moving, the interface is
shown as below. See Figure 4-139.
299
Figure 4-139
Click draw button
to draw the zone. See Figure 4-140.
300
Figure 4-140



Preset: Select a preset you want to use behavior analytics.
Name: Input customized rule name.
Sensitivity: It is to set alarm sensitivity. The value ranges from 1 to 10.The default setup is 5.

Target filter: Click
, you can set filter object size. Each rule can set two sizes (min size/max size).
Once the object is smaller than the min size or larger than the max size, there is no alarm. Please
make sure the max size is larger than the min size.
Now you can draw a rule. Left click mouse to draw a zone, until you draw a rectangle, you can right click
mouse.
Tips
Click
to delete the corresponding rule.
Click
, you can refer to the chapter 4.7.4.1 to set other parameters.
Click Apply to complete the setup.
4.7.4.8 Global Setup (Optional)
After you set the rule(s), you can see the following interface. See Figure 4-141.
301
Figure 4-141
Click Global config button, the interface is shown as below. See Figure 4-142.
 Channel: Please select a channel from the dropdown list.
 Preset: Select a preset you want to set the rule. Please note, you need to add a preset first,
otherwise, you cannot see the preset dropdown list. If there is no preset, you can draw a rule in
current channel.
 Calibration zone:




Click Add zone
, you can draw a calibration zone at the left pane of the interface. Select a zone
and then click Delete zone button; you can remove the selected zone.
Select gauge type (horizontal/tilt), you can set the corresponding length. You can draw three tilt
gauges and one horizontal gauge at the left pane of the interface.
Select Width/Height and then click Verify, you can draw a line in the calibration zone, and then you
can see its actual length.
Refresh preset: Click it to get the latest preset setup.
302
Figure 4-142
4.7.5 Face Detect (Optional)
When camera detects human face, system can generate an alarm.
From main menu->Setting->Event->Face detect, the interface is shown as in Figure 4-143.
 Face ROI: Check the box here, system can enhance the human face display pane.

Log: Check the box here, system can record face detect log.
You can refer to the chapter 0 t to set other parameters.
303
Figure 4-143
4.7.6 People Counting (Optional)
System can calculate the entry/exit people amount in the specified zone. It can generate an alarm when
the amount has exceeded the threshold.
From main menu->Setting->Event->People counting, you can see an interface shown as in Figure 4-144.
 Enable: Check the box to enable people counting function.
 OSD overlay: Check the box here; you can view the people amount on the surveillance video.
 Rule setup: Click Set button, you can set people counting zone, name, and direction (entry/exit).
 Entry No.: It is to set people entry amount. System can generate an alarm once the amount has
exceeded the threshold.
 Exit No.: It is to set people exit amount. System can generate an alarm once the amount has
exceeded the threshold.
 Remaining No.: It is to set people staying amount in the zone. System can generate an alarm once
the amount has exceeded the threshold.
You can refer to the chapter 4.7.1.1 motion detection to set other parameters.
Click OK to complete the setup.
304
Figure 4-144
After you set the people counting function, from main menu->Info->Event->People counting, you can
view people counting statistics report. Please refer to chapter 4.7.1.1 Motion detect for detailed
information.
4.7.7 Heat Map
Device can detect the active object state in the specified region.
Step 1
From main menu->Setting->Event->Heat map.
Enter heat map interface. See Figure 4-145.
305
Figure 4-145
Step 2
Step 3
Select a channel number and then check the box to enable the function.
Click Setup button.
Enter setup interface. See Figure 4-146.
Figure 4-146
Step 4
Set arm/disarm period. Refer to chapter 4.7.1.1 Motion detect for detailed setup information.
306
Step 5
Click Apply button to complete setup.
Note
After set the heat map parameters, go to main menu->Info->Event->Heat map to view heat map
report. Refer to 4.10.2.6 for detailed setup information.
4.7.8 Plate Recognition
4.7.8.1 Plate recognition settings
Device can generate an alarm when it detects the corresponding plate information.
Please follow the steps listed below.
Step 1 From main menu->Setting->Event->Plate recognition->Plate recognition.
Enter plate recognition interface. See Figure 4-147.
Figure 4-147
Step 2
Step 3
Step 4
Check Enable to enable plate recognition function.
Select a channel number and then click the Rule to set the plate recognition name and detection
zone.
Click Regular, blacklist, whitelist to set.
Note
Before use blacklist alarm or whitelist alarm function, please add the corresponding plate
information. Refer to chapter 4.7.8.2 B/W list for detailed information.
 Regular: In this interface, device triggers an alarm when it detects all plate numbers.
 Blacklist: In this interface, device triggers an alarm when it detects plate number in the
307
blacklist.
 Whitelist: In this interface, device triggers an alarm when it detects plate number in the
whitelist.
4.7.8.2 B/W List
It is to set the blacklist and the whitelist. It includes add, delete, import, export blacklist/whitelist.
After setting the blacklist/whitelist, in the plate snapshot list on the preview interface, the blacklist plate
number is red, the whitelist plate number is green, the regular plate number is white.
Add blacklist/whitelist
Step 1 From main menu->Setting->Event->Plate recognition->B/W list.
Enter B/W list interface. See Figure 4-148.
Figure 4-148
Step 2
Step 3
Set plate number and then select type as blacklist or whitelist.
Click Add button.
Delete blacklist/whitelist
Set type as blacklist, whitelist or all, click Search button, device displays the corresponding information.

Check the box before the plate number and then click Delete to delete a plate number. Or click

of the corresponding plate number to delete.
Click Clear to delete all plate information on the blacklist/whitelist.
308
Import/export blacklist/whitelist
Device support blacklist/whitelist import/export function via the USB device. The import file supports .csv
and xlsx. The export file is .csv.
 Import blacklist/whitelist: Set the type as blacklist or whitelist and then click Import button. Select the
corresponding file and then click Open button to import.
 Export blacklist/whitelist: Set the type as blacklist or whitelist and then click Export button. Select the
file save path and then click Save.
Note
When export the blacklist, the file name is “TrafficBlackList_20160321114429_xx.csv”. When export
whitelist, the file name is “TrafficRedList_20160321114429_xx.csv”. The “20160321114429” is file
import/export date.
4.7.9 Audio Detect (Optional)
System can generate an alarm once it detect the audio input is abnormal or audio volume changes.
From main menu->Setting->Event->Audio detect, you can see an interface shown as in Figure 4-149.
 Input abnormal: Check the box here, system can generate an alarm once the audio input is
abnormal.
 Intensity change: Check the box here, system can generate an alarm once the audio volume
becomes strong.
 Sensitivity: It refers to the audio recognition sensitivity. The higher the value is, the higher the
sensitivity is.
 Threshold: It is to set intensity change threshold. The smaller the value is, the higher the sensitivity
is.

Log: Check the box here, system can record audio detect alarm log.
Refer to the chapter 4.7.1.1 Motion Detect to set other parameters.
309
Figure 4-149
4.7.10 Alarm Settings
In the main menu, from Setting->Event->Alarm, you can see alarm setup interface.
 Alarm in: Here is for you to select channel number.
In the main menu, from Setting->Event->Alarm, you can see alarm setup interface. See Figure 4-150.
There are four alarm types. See Figure 4-150 to Figure 4-153.
 Local alarm: The alarm signal system detects from the alarm input port.
 Network alarm: It is the alarm signal from the network.
 IPC external alarm: It is the on-off alarm signal from the front-end device and can activate the local
HNVR.
 IPC offline alarm: Once you select this item, system can generate an alarm when the front -end IPC
disconnects with the local HNVR. The alarm can activate record, PTZ, snap and etc. The alarm can
last until the IPC and the HNVR connection resumes.
Important
 If it is your first time to boot up the device, the disconnection status of the front -end
network camera will not be regarded as offline. After one successfully connection, all
the disconnection events will be regarded as IPC offline event.
 When IPC offline alarm occurs, the record and snapshot function of digital channel is
null.
 Enable: Please you need to highlight this button to enable current function.
 Type: normal open or normal close.

Period: Click set button, you can see an interface is shown as in Figure 4-155. There are two ways
for you to set periods. There are max 6 periods in one day. There are four record types: regular,
310
motion detection (MD), Alarm, MD & alarm.

In Figure 4-155, Select icon
Now the icon is shown as
of several dates, all checked items can be edited together.
. Click
to delete a record type from one period.









In Figure 4-155. Click button
after one date or a holiday, you can see an interface shown
as in Figure 4-156. There are four record types: regular, motion detection (MD), Alarm, MD &
alarm.
PTZ activation: When an alarm occurred, system can activate the PTZ operation. The PTZ activation
lasts an anti-dither period. See Figure 4-154.
Anti-dither: Here you can set anti-dither time. The value ranges from 5 to 600s. The anti-dither time
refers to the alarm signal lasts time. It can be seem as the alarm signal activation stays such as the
buzzer, tour, PTZ activation, snapshot, channel record. The stay time here does not include the latch
time. During the alarm process, the alarm signal can begin an anti-dither time if system detects the
local alarm again. The screen prompt, alarm upload, email and etc will not be activated. For example,
if you set the anti-dither time as 10 second, you can see the each activation may last 10s if the local
alarm is activated. During the process, if system detects another local alarm signal at the fifth
second, the buzzer, tour, PTZ activation, snapshot, record channel will begin another 10s while the
screen prompt, alarm upload, email will not be activated again. After 10s, if system detects another
alarm signal, it can generate an alarm since the anti-dither time is out.
Alarm output: The number here is the device alarm output port. You can select the corresponding
ports(s) so that system can activate the corresponding alarm device(s) when an alarm occurred.
Latch: When the anti-dither time ended, the channel alarm you select in the alarm output may last
the specified period. The value ranges from 1 to 300 seconds. This function is not for other alarm
activation operations. The latch is still valid even you disable the alarm event function directly.
Show message: System can pop up a message to alarm you in the local host screen if you enabled
this function.
Alarm upload: System can upload the alarm signal to the network (including alarm center and the
WEB) if you enabled current function. System only uploads the alarm channel status. You can go
to the WEB and then go to the Alarm interface to set alarm event and alarm operation. Please go
to the Network interface to set alarm center information.
Send email: System can send out the alarm signal via the email to alert you when alarm occurs.
Once you enable the snap function, system can also send out an image as the attachment. Please
go to the Main Menu->Setting ->Network->Email interface to set.
Record channel: you can select proper channel to record alarm video (Multiple choices).
 You need to set alarm record mode as Schedule in Record interface (Main
Menu->Advanced->Record). Please note the manual record has the highest priority. System
record all the time no matter there is an alarm or not if you select Manual mode.
 Now you can go to the Schedule interface (Main Menu->Setting->Schedule) to set the record
type, corresponding channel number, week and date. You can select the record
type:Regular/MD/Alarm/MD&Alarm. Please note, you cannot select the MD&Alarm and MD(or
Alarm) at the same time.
 Now you can go to the Encode interface to select the alarm record and set the encode
parameter (Main Menu->Setting->Encode).
311




Finally, you can set the alarm input as the local alarm and then select the record channel. The
select channel begins alarm record when an alarm occurred. Please note system begins the
alarm record instead of the MD record if the local alarm and MD event occurred at the same
time.
Tour: Here you can enable tour function when an alarm occurs. System supports 1/8-window tour.
Please go to chapter4.3.6.2 Display for tour interval setup. Please note the tour setup here has
higher priority than the tour setup you set in the Display interface. Once there two tours are both
enabled, system can enable the alarm tour as you set here when an alarm occurred. If there is no
alarm, system implements the tour setup in the Display interface.
Snapshot: You can enable this function to snapshot image when an alarm occurs.
Buzzer: Highlight the icon to enable this function. The buzzer beeps when an alarm occurs.
Figure 4-150
312
Figure 4-151
.
Figure 4-152
313
Figure 4-153
Figure 4-154
314
Figure 4-155
Figure 4-156
Please highlight icon
to select the corresponding function. After setting all the setups please
click save button.
4.7.11 Abnormality
There are three types: Disk/Network/User.
 Disk: Disk error, no disk, no space. See Figure 4-157.
 Network: Disconnection, IP conflict, MAC conflict. See Figure 4-158.
 User: Illegal login. Figure 4-159.
315









Alarm output: Please select alarm activation output port (multiple choices).
Less than: System can alarm you when the HDD space is less than the threshold you set here
(For HDD no space type only).
Attempts: In user interface, select illegal login from the dropdown list. Here you can set login
attempts. The value ranges from 1 to 10.
Lock time: In user interface, select illegal login from the dropdown list. Here you can set account
lock time. The value ranges from 1 to 30 minutes.
Latch: Here you can set corresponding delaying time. The value ranges from 1s-300s. System
automatically delays specified seconds in turning off alarm and activated output after external alarm
cancelled.
Show message: system can pop up the message in the local screen to alert you when alarm
occurs.
Alarm upload: System can upload the alarm signal to the network (including alarm center) if you
enabled current function. For disconnection event, IP conflict event and MAC conflict event, this
function is null.
Send email: System can send out email to alert you when alarm occurs.
Buzzer: Highlight the icon to enable this function. The buzzer beeps when an alarm occurs.
Figure 4-157
316
Figure 4-158
Figure 4-159
4.7.12 Alarm output
From Main menu->Setting->Event->Alarm output, you can see an interface shown as in Figure 4-160.
317
Here is for you to set proper alarm output (Auto/manual/stop).
Click OK button of the alarm reset, you can clear all alarm output status.
Figure 4-160
Please highlight icon
to select the corresponding alarm output.
After all the setups please click OK button.
4.8
Network
4.8.1 Network Settings
4.8.1.1 TCP/IP
The single network adapter interface is shown as in Figure 4-161 and the dual network adapters interface
is shown as in Figure 4-162.
 Network Mode : Includes multiple access, fault tolerance, and load balancing
 Multiple-address mode: eth0 and eth1 operate separately. You can use the services such as
HTTP, RTP service via etho0 or the eth1. Usually you need to set one default card (default setup
is etho) to request the auto network service form the device-end such as DHCP, email, FTP and
etc. In multiple-address mode, system network status is shown as offline once one card is
offline.
 Network fault-tolerance: In this mode, device uses bond0 to communicate with the external
devices. You can focus on one host IP address. At the same time, you need to set one master
card. Usually there is only one running card (master card).System can enable alternate card
when the master card is malfunction. The system is shown as offline once these two cards are
both offline. Please note these two cards shall be in the same LAN.
318


Load balance: In this mode, device uses bond0 to communicate with the external device. T he
eth0 and eth1 are both working now and bearing the network load. Their network load are
general the same. The system is shown as offline once these two cards are both offline. Please
note these two cards shall be in the same LAN.
Default Network Card: Please select eth0/eth1/bond0(optional) after enable multiple-access
function

Main Network Card: Please select eth0/eth1 (optional).after enable multiple access function.
Note: The dual-Ethernet port series support the above three configurations and suppor ts
functions as multiple-access, fault-tolerance and load balancing.

IP Version: There are two options: IPv4 and IPv6. Right now, system supports these two IP address
format and you can access via them.
 MAC address: The host in the LAN can get a unique MAC address. It is for you to access in the LAN. It is
read-only.
 IP address: Here you can use up/down button () or input the corresponding number to input IP
address. Then you can set the corresponding subnet mask the default gateway.
 Default gateway: Here you can input the default gateway. Please note system needs to check the
validity of all IPv6 addresses. The IP address and the default gateway shall be in the same IP
section. That is to say, the specified length of the subnet prefix shall have the same string.
 DHCP: It is to auto search IP. When enable DHCP function, you cannot modify IP/Subnet mask
/Gateway. These values are from DHCP function. If you have not enabled DHCP function, IP/Subnet
mask/Gateway display as zero. You need to disable DHCP function to view current IP information.
Besides, when PPPoE is operating, you cannot modify IP/Subnet mask /Gateway.
 MTU: It is to set MTU value of the network adapter. The value ranges from 1280 -7200 bytes. The
default setup is 1500 bytes. Please note MTU modification may result in network adapter reboot and
network becomes off. That is to say, MTU modification can affect current network service. System
may pop up dialog box for you to confirm setup when you want to change MTU setup. Click OK
button to confirm current reboot, or you can click Cancel button to terminate current modification.
Before the modification, you can check the MTU of the gateway; the MTU of the NVR shall be the
same as or is lower than the MTU of the gateway. In this way, you can reduce packets and enhance
network transmission efficiency.
The following MTU value is for reference only.
 1500: Ethernet information packet max value and it is also the default value. It is the typical
setup when there is no PPPoE or VPN. It is the default setup of some router, switch or the
network adapter.
 1492: Recommend value for PPPoE.
 1468: Recommend value for DHCP.
 Preferred DNS server: DNS server IP address.
 Alternate DNS server: DNS server alternate address.
 Transfer mode: Here you can select the priority between fluency/video qualities.
 LAN download: System can process the downloaded data first if you enable this function. The
download speed is 1.5X or 2.0X of the normal speed.
 LAN download: System can process the downloaded data first if you enable this function. The
download speed is 1.5X or 2.0X of the normal speed.
After completing all the setups please click save button, system goes back to the previous menu.
319
Figure 4-161
Figure 4-162
4.8.1.2 Connection
The connection setup interface is shown as in Figure 4-163.
 Max connection: The max client login amount (such as WEB, platform, cellphone and etc). The value
ranges from 1 to 128(default).
320
 TCP port: Default value is 37777.
 UDP port: Default value is 37778.
 HTTP port: Default value is 80.
 HTTPS port: Default value is 443.
 RTSP port: Default value is 554.
Important: System needs to reboot after you changed and saved any setup of the above four ports.
Please make sure the port values here do not conflict.
Figure 4-163
4.8.1.3 WIFI AP
Note
This function is for some series product only.
4.8.1.3.1
WIFI AP
The WIFI AP interface is shown as below. See Figure 4-164. Here you can set WIFI hotspot, so that the
network camera can use the hotspot to connect to the network.
 2.4GHz/5GHz: Please check the box to enable the function.
 SSID: It is to set SSID name. You can use this name to search the device.
 Password: It is to set SSID password. You can use this password to connect to the network.
 Security: Select authentication mode from the dropdown list.
 Channel: Please select a channel from the dropdown list. The default setup is auto.
 Mode: There three options: high/middle/low. Please select from the dropdown list.
321
Figure 4-164
4.8.1.3.2
Advanced
Click Advanced, you can see an interface shown as below. See Figure 4-165.
 IPv4 address: Input WIFI AP IP address.
 IPv4 net mask: Input WIFI AP network mask.
 IPv4 gateway: Input WIFI AP gateway.
 Start IP/End IP: Input start IP and end IP of the network cameras. The NVR can allocate the IP
addresses in the range you specified here.
 Upgrade: Click it to upgrade WIFI AP module.
322
Figure 4-165
4.8.1.4 WIFI
The WIFI interface is shown as below. See Figure 4-166.
 Enable: Check the box here to enable WIFI function.
 Refresh: You can click it to search the hotspot list again. It can automatically add the information
such as the password if you have set it before.
 Disconnect: Here you can click it to turn off the connection.
 Connect: Here you can click it to connect to the hotspot. System needs to turn off current connection
and then connect to a new hotspot if there is connection of you selected one.
323
Figure 4-166
 WIFI working status: Here you can view current connection status.
Please note:
 After successful connection, you can see WIFI connection icon at the top right corner of the preview
interface.
 When the hotspot verification type is WEP, system displays as AUTO since the device cannot detect
its encryption type.
 System does not support verification type WPA and WPA2. The display may become abnormal for
the verification type and encryption type.
After device successfully connected to the WIFI, you can view the hotspot name, IP address, subnet
mask, default gateway and etc. Right now system support TOTOLINK_N2200UP module.
4.8.1.5 3G
3G setup interface is shown as below. See Figure 4-167.
Please refer to the following contents for the parameter information.
 Pane 1: Display 3G signal intensity after you enabled 3G function.
 Pane 2: Display 3G module configuration information after you enabled 3G function.
 Pane 3: Display 3G module status information after you enabled 3G function.
It is to display current wireless network signal intensity such as EVDO, CDMA1x, WCDMA, WCDMA,
EDGE and etc.
 3G module: It is to display current wireless network adapter name.
 3G Enable/Disable: Check the box here to enable 3G module.
 Network type: There are various network types for different 3G network modules. You can select
according to your requirements.
324








APN: It is the wireless connection server. It is to set you access the wireless network via which
method.
AUTH: It is the authentication mode. It supports PAP/CHAP.
Dial number: Please input 3G network dialup number you got from your ISP.
User name: It is the user name for you to login the 3G network.
Password: It is the password for you to login the 3G network.
Pulse interval: You can set dialup duration. Once you disable the extra stream, the connection time
begins. For example, if you input 5 seconds here, then 3G network connection period is 5 seconds.
The device automatically disconnect when time is up. If there is no extra stream, 3G network
connection is valid all the time. If the alive time is 0, then the 3G network connection is valid all
the time.
Dial: Here you can enable or disable 3G network connection/disconnection manually.
3G wireless network: Here is to display wireless network status, SIM card status, dial status. If the 3G
connection is OK, then you can see the device IP address the wireless network automatically
allocates.
1
2
3
Figure 4-167
4.8.1.6 PPPoE
PPPoE interface is shown as in Figure 4-168.
Input “PPPoE name” and “PPPoE password” you get from your ISP (Internet service provider).
Click save button, you need to restart to activate your configuration.
After rebooting, NVR will connect to internet automatically. The IP in the PPPoE is the NVR dynamic
value. You can access this IP to visit the unit.
325
Figure 4-168
4.8.1.7 DDNS
DDNS setup interface is shown as in Figure 4-169.
You need a PC of fixed IP in the internet and there is the DDNS software running in this PC. In other
words, this PC is a DNS (domain name server).
In network DDNS, please select DDNS type and highlight enable item. And them please input your
PPPoE name you get from you IPS and server IP (PC with DDNS). Click save button and then reboot
system.
Click save button, system prompts for rebooting to get all setup activated.
After rebooting, open IE and input as below:
http://(DDNS server IP)/(virtual directory name)/webtest.htm
e.g.: http://10.6.2.85/NVR _DDNS/webtest.htm.)
Now you can open DDNSServer web search page.
326
Figure 4-169
Please note DDNS type includes: CN99 DDNS, NO-IP DDNS, Quick DDNS, Dyndns DDNS and sysdns
DDNS. All the DDNS can be valid at the same time, you can select as you requirement.
Private DDNS function shall work with special DDNS server and special Professional Surveillance
Software (PSS).
Quick DDNS and Client-end Introduction
1) Background Introduction
Device IP is not fixed if you use ADSL to login the network. The DDNS function allows you to access the
NVR via the registered domain name. Besides the general DDNS ,the Quick DDNS works with the device
from the manufacturer so that it can add the extension function.
2) Function Introduction
The quick DDNS client has the same function as other DDNS client end. It realizes the bonding of the
domain name and the IP address. Right now, current DDNS server is for our own devices only. You need
to refresh the bonding relationship of the domain and the IP regularly. There is no user name, password
or the ID registration on the server. At the same time, each device has a default domain name (Generated
by MAC address) for your option. You can also use customized valid domain name (has not registered.).
3) Operation
Before you use Quick DDNS, you need to enable this service and set proper server address, port value
and domain name.

Server address:www.quickddns.com

Port number:80

Domain name:There are two modes: Default domain name and customized domain name.
Except default domain name registration, you can also use customized domain name (You can input your
self-defined domain name.) After successful registration, you can use domain name to login installed of
327
the device IP.

User name: It is optional. You can input your commonly used email address.
Important
 Do not register frequently. The interval between two registrations shall be more than 60 seconds. Too
many registration requests may result in server attack.
 System may take back the domain name that is idle for one year. You can get a notification email
before the cancel operation if your email address setup is OK.
4.8.1.8 UPnP
The UPNP protocol is to establish a mapping relationship between the LAN and the WAN. Please input
the router IP address in the LAN in Figure 4-161. See Figure 4-170.
 UPNP on/off :Turn on or off the UPNP function of the device.
 Status: When the UPNP is offline, it shows as “Unknown”. When the UPNP works it shows
“Success”
 Router LAN IP: It is the router IP in the LAN.
 WAN IP: It is the router IP in the WAN.
 Port Mapping list: The port mapping list here is the one to one relationship with the router’s port
mapping setting.
 List:

Service name:Defined by user.

Protocol: Protocol type

Internal port:Port that has been mapped in the router.
 External port:Port that has been mapped locally.
 Default: UPNP default port setting is the HTTP, TCP and UDP of the NVR.
 Add to the list: Click it to add the mapping relationship.
 Delete: Click it to remove one mapping item.
Double click one item; you can change the corresponding mapping information. See Figure 4-171.
Important:
When you are setting the router external port, please use 1024~5000 port. Do not use well-known
port 1~255 and the system port 256~1023 to avoid conflict.
For the TCP and UDP, please make sure the internal port and external port are the same to
guarantee the proper data transmission.
328
Figure 4-170
Figure 4-171
4.8.1.9 IP Filter
IP filter interface is shown as in Figure 4-172. You can add IP in the following list. The list supports max 64
IP addresses. System supports valid address of IPv4 and IPv6. Please note system needs to check the
validity of all IPv6 addresses and implement optimization.
After you enabled trusted sites function, only the IP listed below can access current NVR.
If you enable blocked sites function, the following listed IP addresses cannot access current NVR.
 Enable: Highlight the box here, you can check the trusted site function and blocked sites function.
You cannot see these two modes if the Enable button is grey.
329

Type: You can select trusted site and blacklist from the dropdown list. You can view the IP address
on the following column.
 Start address/end address: Select one type from the dropdown list, you can input IP address in the
start address and end address. Now you can click Add IP address or Add IP section to add.
a) For the newly added IP address, it is in enable status by default. Remove the √ before the item,
and then current item is not in the list.
b) System max supports 64 items.
c) Address column supports IPv4 or IPv6 format. If it is IPv6 address, system can optimize it. For
example, system can optimize aa:0000: 00: 00aa: 00aa: 00aa: 00aa: 00aa as aa:: aa: aa: aa: aa:
aa: aa.
d) System automatically removes space if there is any space before or after the newly added IP
address.
e) System only checks start address if you add IP address. System check start address and end
address if you add IP section and the end address shall be larger than the start address.
f) System may check newly added IP address exists or not. System does not add if input IP
address does not exist.
 Delete: Click it to remove specified item.
 Edit: Click it to edit start address and end address. See Figure 4-173. System can check the IP
address validity after the edit operation and implement IPv6 optimization.
 Default: Click it to restore default setup. In this case, the trusted sites and blocked sites are both null.
Note:
 If you enabled trusted sites, only the IP in the trusted sites list can access the device.
 If you enabled blocked sites, the IP in the blocked sites cannot access the device.
 System supports add MAC address.
Figure 4-172
330
Figure 4-173
4.8.1.10 Email
The email interface is shown as below. See Figure 4-174.
 SMTP server: Please input your email SMTP server IP here.
 Port: Please input corresponding port value here.
 User name: Please input the user name to login the sender email box.
 Password: Please input the corresponding password here.
 Sender: Please input sender email box here.
 Title: Please input email subject here. System support English character and Arabic number. Max
32-digit.
 Receiver: Please input receiver email address here. System max supports 3 email boxes. System
automatically filters same addresses if you input one receiver repeatedly.
 SSL enable: System supports SSL encryption box.
 Interval: The send interval ranges from 0 to 3600 seconds. 0 means there is no interval.
 Health email enable: Please check the box here to enable this function. This function allows the
system to send out the test email to check the connection is OK or not.
 Interval: Please check the above box to enable this function and then set the corresponding interval.
System can send out the email regularly as you set here. Click the Test button, you can see the
corresponding dialogue box to see the email connection is OK or not.
Please note system will not send out the email immediately when the alarm occurs. When the alarm,
motion detection or the abnormity event activates the email, system sends out the email according to the
interval you specified here. This function is very useful when there are too many emails activated by the
abnormity events, which may result in heavy load for the email server.
331
Figure 4-174
4.8.1.11 FTP
You need to download or buy FTP service tool (such as Ser-U FTP SERVER) to establish FTP service.
Please install Ser-U FTP SERVER first. From “start” -> “program” -> Serv-U FTP Server -> Serv-U
Administrator. Now you can set user password and FTP folder. Please note you need to grant write right
to FTP upload user. See Figure 4-175.
Figure 4-175
You can use a PC or FTP login tool to test setup is right or not.
For example, you can login user ZHY to FTP://10.10.7.7
and then test it can modify or delete folder
or not. See Figure 4-176.
H140H 140H 140HTU
UTH
332
Figure 4-176
System also supports upload multiple NVRs to one FTP server. You can create multiple folders under this
FTP.
FTP interface is shown as in Figure 4-177.
Please highlight the icon
in front of Enable to activate FTP function.
Here you can input FTP server address, port and remote directory. When remote directory is null, system
automatically create folders according to the IP, time and channel.
User name and password is the account information for you to login the FTP.
File length is upload file length. When setup is larger than the actual file length, system will upload the
whole file. When setup here is smaller than the actual file length, system only uploads the set length and
auto ignore the left section. When interval value is 0, system uploads all corresponding files.
After completed channel and weekday setup, you can set two periods for one each channel.
Click the Test button, you can see the corresponding dialogue box to see the FTP connection is OK or
not.
Figure 4-177
333
4.8.1.12 SNMP
SNMP is an abbreviation of Simple Network Management Protocol. It provides the basic network
management frame of the network management system. The SNMP widely used in many environments.
It is used in many network device, software and system.
You can set in the following interface. See Figure 4-178.
Figure 4-178
Please enable the SNMP function. Use the corresponding software tool (MIB Builder and MG-SOFT MIB
Browser. You still need two MIB file: BASE-SNMP-MIB, NVR-SNMP-MIB) to connect to the device. You
can get the device corresponding configuration information after successfully connection.
Please follow the steps listed below to configure.
 In Figure 4-178, check the box to enable the SNMP function. Input the IP address of the PC than is
running the software in the Trap address. You can use default setup for the rest items.
 Compile the above mentioned two MIB file via the software MIB Builder.
 Run MG-SOFT MIB Browser to load the file from the previous step to the software.
 Input the device IP you want to manage in the MG-SOFT MIB Browser. Please set the corresponding
version for your future reference.
 Open the tree list on the MG-SOFT MIB Browser; you can get the device configuration. Here you can
see the device has how many video channels, audio channels, application version and etc.
Note
Port conflict occurs when SNMP port and Trap port are the same.
4.8.1.13 Multicast
Multicast setup interface is shown as in Figure 4-179.
334
Figure 4-179
Here you can set a multiple cast group. Please refer to the following sheet for detailed information.
 IP multiple cast group address
-224.0.0.0-239.255.255.255
-“D” address space
 The higher four-bit of the first byte=”1110”
 Reserved local multiple cast group address
-224.0.0.0-224.0.0.255
-TTL=1 When sending out telegraph
-For example
224.0.0.1 All systems in the sub-net
224.0.0.2 All routers in the sub-net
224.0.0.4 DVMRP router
224.0.0.5 OSPF router
224.0.0.13 PIMv2 router
 Administrative scoped addressees
-239.0.0.0-239.255.255.255
-Private address space
 Like the single broadcast address of RFC1918
 Cannot be used in Internet transmission
 Used for multiple cast broadcast in limited space.
Except the above mentioned addresses of special meaning, you can use other addresses. For example:
Multiple cast IP: 235.8.8.36
Multiple cast PORT: 3666.
335
After you logged in the Web, the Web can automatically get multiple cast address and add it to the
multiple cast groups. You can enable real-time monitor function to view the view.
Please note multiple cast function applies to special series only.
4.8.1.14 Alarm Centre
This interface is reserved for you to develop. See Figure 4-180.
Figure 4-180
4.8.1.15 Auto register
This function allows the device to auto register to the proxy you specified. In this way, you can use the
client-end to access the NVR and etc via the proxy. Here the proxy has a switch function. In the network
service, device supports the server address of IPv4 or domain.
Please follow the steps listed below to use this function.
Please set proxy server address, port, and sub-device name at the device-end. Please enable the auto
register function, the device can auto register to the proxy server.
1) The setup interface is shown as in Figure 4-181.
Important
Do not input network default port such as TCP port number.
336
Figure 4-181
2) The proxy server software developed from the SDK. Please open the software and input the global
setup. Please make sure the auto connection port here is the same as the port you set in the previous
step.
3) Now you can add device. Please do not input default port number such as the TCP port in the mapping
port number. The device ID here shall be the same with the ID you input in Figure 4-181. Click Add button
to complete the setup.
4) Now you can boot up the proxy server. When you see the network status is Y, it means your
registration is OK. You can view the proxy server when the device is online.
Important
The server IP address can also be domain. But you need to register a domain name before you run proxy
device server.
4.8.1.16 P2P
You can use your cell phone to scan the QR code and add it to the cell phone client.
Via the SN from scanning the QR code, you can access the device in the WAN. Please refer to the P2P
operation manual included in the resources CD.
From main menu->Setting->Network->P2P, you can go to the following interface, the P2P interface is
shown as in Figure 4-182.
337
Figure 4-182
 Android:
Open Google Play app in your smart phone. Search gDMSS Lite or gDMSS Plus, download it and install.
 iOS:
Open App Store app in your smart phone. Search iDMSS Lite or iDMSS Plus, download it and install.
Please follow the steps listed below.

Open App; tap

Tap

Tap Device manager button, you can use several modes (P2P/DDNS/IP and etc) to add the device.
to go to the Live preview.
at the top left corner, you can see the main menu.
Click
to save current setup. Tap Start Live preview to view all-channel video from the
connected device. See Figure 4-183.
338
Figure 4-183
4.8.1.17 Easy Space
This function allows you to upload motion detect record or snapshot image to the dropbox and etc.
The easy space interface is shown as below. See Figure 4-184.
Please select the easy space address from the dropdown list and then input corresponding user name
and password.
Figure 4-184
339
Note:
 The uploaded file is for sub stream only. Please go to record control interface (main
stream->setting->Storage->Record) and then select sub stream.
 The easy space function uses upload bandwidth. Usually the recommended upload bandwidth shall
be more than 512kbps and please make sure the network is stable.
 The easy space upload data adopts safe SSL encryption connection. Please enable 1-channel to
upload in case this function occupies too much CPU.
4.8.1.18 SWITCH
It is for you to set IP address, subnet mask, gateway and etc of the Switch. See Figure 4-185.
Figure 4-185
4.8.2 Network Test
In this interface, you can see network test and network load information.
4.8.2.1 Network Test
From main menu->Info-Network->Test, the network test interface is shown as in Figure 4-186.
 Destination IP: Please input valid IPV4 address and domain name.
 Test: Click it to test the connection with the destination IP address. The test results can display
average delay and packet loss rate and you can also view the network status as OK, bad, no
connection and etc.
 Network Sniffer backup: Please insert USB2.0 device and click the Refresh button, you can view the
device on the following column. You can use the dropdown list to select peripheral device. Click
Browse button to select the snap path. The steps here are same as preview backup operation.
340
You can view all connected network adapter names (including Ethernet, PPPoE, WIFI, and 3G), you can
click the button
on the right panel to begin Sniffer. Click the grey stop button to stop. Please note
system cannot Sniffer several network adapters at the same time.
After Sniffer began, you can exit to implement corresponding network operation such as login WEB,
monitor. Please go back to Sniffer interface to click
stop Sniffer. System can save the packets to the
specified path. The file is named after “Network adapter name+time”. You can use software such as
Wireshark to open the packets on the PC for the professional engineer to solve complicated problems.
Figure 4-186
4.8.2.2 Network Load
From main menu->Info-Network->Load, network load is shown as in Figure 4-187. Here you can view the
follow statistics of the device network adapter.
Here you can view information of all connected network adapters. The connection status is shown as
offline if connection is disconnected. Click one network adapter, you can view the flow statistics such as
send rate and receive rate at the top panel
341
Figure 4-187
4.9
HDD Setup
Here you can view HDD information such as type, status, total capacity, record time and etc. The
operation includes format, resume from error, change HDD property (Read write, Read-only). Here you
can also set alarm and HDD storage position.
4.9.1 Format
a) From Mani-menu->Setting->Storage->HDD Manager, you can go to HDD management interface.
See Figure 4-188.
342
Figure 4-188
b) Select a HDD and then select format from the dropdown list. Click Execute button.
c) Click OK button to complete the setup. You can see system needs to restart to activate current setup.
4.9.2 HDD Information
Here is to list hard disk type, total space, free space, and status. See Figure 4-189.
○ means current HDD is normal.. - means there is no HDD.
If disk is damaged, system shows as “?”. Please remove the broken hard disk before you add a new one.
343
Figure 4-189
In Figure 4-189, click one HDD item, the S.M.A.R.T interface is shown as in Figure 4-190.
Figure 4-190
344
Parameter
Function
SATA
1 here means there is 1 HDD.
For different series product, the max HDD amount may vary,
When HDD is working properly, system is shown as O. . “_” means there is
no HDD.
SN
You can view the HDD amount the device connected to;
﹡ means the second HDD is current working HDD.
Type
The corresponding HDD property.
Total space
The HDD total capacity.
Free space
The HDD free capacity.
Status
HDD can work properly or not.
Bad track
Display there is bad track or not.
Page up
Click it to view previous page.
Page down
Click it to view the next page.
View
recording time
Click it to view HDD record information (file start time and end time).
View
HDD
type
and
capability
Click it to view HDD property, status and etc,
4.9.3 Advanced
It is to set HDD group, and HDD group setup for main stream, sub stream and snapshot operation
Important
HDD group and quota mode cannot be valid at the same time. System needs to restart once you
change the mode here.
The HDD group mode is shown as in Figure 4-191.
 HDD: Here you can view the HDD amount the device can support.
 Group: It lists the HDD Group number of current hard disk.
345
Figure 4-191
Please select the correspond group from the dropdown list and then click Apply button.
Click main stream/sub stream/snapshot button to set corresponding HDD group information. See Figure
4-192 through Figure 4-194.
Figure 4-192
346
Figure 4-193
Figure 4-194
4.9.4 HDD Detect
Note
This function is for some series product only.
The HDD detect function is to detect HDD current status so that you can clearly understand the HDD
performance and replace the malfunction HDD.
There are two detect types:
347


Quick detect is to detect via the universal system files. System can quickly complete the HDD
scan. If you want to use this function, please make sure the HDD is in use now. If the HDD is
removed from other device, please make sure the write-data once was full after it installed on
current device.
Global detect adopts Windows mode to scan. It may take a long time and may affect the HDD
that is recording.
4.9.4.1 Manual Detect
From main menu->Setting->Storage->HDD Detect->Manual Detect, the interface is shown as below. See
Figure 4-195.
Please select detect type and HDD. Click start detect to begin. You can view the corresponding detect
information.
Figure 4-195
4.9.4.2 Detect Report
After the detect operation, you can go to the detect report to view corresponding information.
From main menu->Setting->Storage->HDD Detect->Manual Detect, the interface is shown as below. See
Figure 4-196.
348
Figure 4-196
Click View, you can see the detailed information such as detect result, backup and S.M.A.R.T. See Figure
4-197 and Figure 4-198.
Figure 4-197
349
Figure 4-198
4.9.5 RAID Manager
Important
Please make sure your purchased product support the RAID function, otherwise you cannot see
the following interface.
Right now, RAID supports Raid0, Raid1, Raid5, Raid6, and Raid10. Local hotspare supports Raid1,
Raid5, Raid6, and Raid10.
4.9.5.1 RAID Config
It is for you to manage RAID HDD. It can display RAID name, type, free space, total space, status and etc.
Here you can add/delete RAID HDD.
Click Add button to select RAID type and then select HDDs, click OK button to add. See Figure 4-199.
350
Figure 4-199
4.9.5.2 Hotspare disks
Click Hotspare disks tab name, you can add the hot spare HDD. See Figure 4-200. The type includes two
options:
 Global: It is global hotspare disk. When any RAID becomes degrading, it can replace and build the
RAID.
 Local: It is local hotspare disk. When the specified RAID becomes degrading, it can replace and build
the RAID.
Select a hot spare device and then click Delete button. Click Apply button to delete.
351
Figure 4-200
4.10 Device Maintenance and Manager
4.10.1 Account
Here is for you to implement account management. See Figure 4-201. Here you can manage user, user
group, and security questions.
Warning
The default user name of different series products may not the same. Please refer to the actula product
for detailed information.
Default user name and authorities
There are three default users: admin/888888 and hidden user “default”.
 Account admin: User admin is device default user of the high-level authorities. The password is what
you set in chapter 4.1.2 Device initialization..
 Account 888888: The user name is 888888 and the password is 888888. It is the device default user
of the high-level authorities. It is for local menu to login only.
 Hidden user default is for system interior use only and cannot be deleted. When there is no login
user, hidden user “default” automatically login. It has the monitor right of all channels by default. The
“default” of some series product may have PTZ control right. Please refer to the actual product. . You
can set some rights such as monitor for this user so that you can view some channel view without
login.
 Usually the ordinary user authorities shall be lower than the advanced user.
352
User group and User
The account adopts two-level management mechanism. The group name and user name shall be unique.
 The default user amount is 64 and the default group amount is 20.
 The factory default user group includes: user and admin. These two groups cannot be deleted.
 Change the group authorities to change the user rights in the same group. The authorities of user
admin and 888888 are ready-only.
 Each user shall only belong to one group. The user authorizes shall be equal to or lower than its
group authorities.
 For the user account name and the user group, the string length ranges from 1 to 31-byte. The string
includes the letter, number, underline, and connector.
After all the setups please click save button.
Figure 4-201
4.10.1.1.1 Add User
Click modify user button
in Figure 4-201 , the interface is shown as in Figure 4-202.
Please input the user name, password, select the group it belongs to from the dropdown list.
Then you can check the corresponding rights for current user.
For convenient user management, usually we recommend the general user right is lower than the admin
account.
353
Figure 4-202
When you create a new user, you can input the corresponding MAC address of current user. If you leave
this item in blank, any MAC address user can share this user account to login. Please note system needs
to check the validity of MAC. Only the 12-digit 0-f format address can pass the validity verification.
System only saves small character even you input capitalized one. You can see the corresponding
prompt if there is any illegal input.
Click the Set button after the period, you can set valid period to use current account. See Figure 4-203.
354
Figure 4-203
Click Set button, you can set six periods in one day. See Figure 4-204.
Check the box after the period, you can enable current setup.
Figure 4-204
355
4.10.1.1.2 Modify user
Click
, you can go to the following interface to change user information. See Figure 4-205.
For admin, 888888, and default (hidden user), you cannot change period setup.
Figure 4-205
4.10.1.1.3 Change Password
In Figure 4-205, check the Modify password box, you can change password. Please input old password,
and then input new password twice to confirm.
The password can contain 32-byte and the space at the begin or at the end of the password are null. It
can contain in the middle of the password. For the user of account right, it can change the password of
other users.
4.10.1.1.4 Add/Modify Group
In Figure 4-201, click Group button, you can see the following interface. See Figure 4-206.
356
Figure 4-206
Click add group button in Figure 4-206 , the interface is shown as below. See Figure 4-207.
Here you can input group name and then input some memo information if necessary.
There are total 98 rights such as control panel, shut down, real-time monitor, playback, record, record file
backup, PTZ, user account, system information view, alarm input/output setup, system setup, log view,
clear log, upgrade system, control device and etc.
Figure 4-207
357
4.10.1.1.5 Security Question
The security question is shown as below. See Figure 4-208.
Here you can change security questions.
Figure 4-208
4.10.1.1.6 ONVIF User
When the camera from the third party is connected with the NVR via the ONVIF user, please use the
verified ONVIF account to connect to the NVR. From main menu->Setting->System->Account->ONVIF
User, you can add/delete/modify user. See Figure 2-50.
Note
The default ONVIF user is admin and the password is what you set in chapter 4.1.2 Device initialization.
The account is read-only.
358
Figure 4-209
Click Add user button, you can see the following interface. See Figure 4-210.
Figure 4-210
Please set user name, password and then select group from the dropdown list.
Click Save to complete setup.
Tips
Click
to change user information, click
to delete current user.
359
4.10.2 System Info
4.10.2.1 Version
From main menu->Info->System->version, you can go to version interface.
Here is for you to view some version information. See Figure 4-211. Please note the following figure
for reference only.
 Channel
 Alarm in
 Alarm out
 System version
 Build Date
 Web
 Serial number
Figure 4-211
4.10.2.2 BPS
Here is for you to view current video bit rate (kb/s) and resolution. See Figure 4-212.
360
Figure 4-212
4.10.2.3 Online User
Here is for you manage online users connected to your NVR. See Figure 4-213.
You can click button
to disconnect or block one user if you have proper system right.
System detects there is any newly added or deleted user in each five seconds and refresh the list
automatically.
361
Figure 4-213
4.10.2.4 Alarm Status
From main menu->info-Event, here you can view the channel status of the remote device, connection log
and etc. See Figure 4-214.
Figure 4-214
362
4.10.2.5 People Counting
It is to search and view the people counting results of each channel. System can export people counting
report. The export file extension name is .bmp.
From main menu->Info->Event->People Counting, you can go to the following interface. See Figure
4-215.
Channel: Please select a channel from the dropdown list.
 Type: Please select report type from the dropdown list. It includes daily report/monthly report/annual
report. You can click to select histogram or polygon chart.
 Start time/end time: Input start time and end time of the people counting.
 Enter: Check to search enter amount.
 Exit: Check the box to search exit amount.
 Display No.: Check the box, system can display enter and exit people amount in the report.
Figure 4-215
4.10.2.6 Heat Map
It is to search and view the heat map of each channel.
From main menu->Info->Event->Heat Map, you can go to the following interface. See Figure 4-216.
Select a channel, input start time and end time. Please note the report search period shall be within one
month.
Click Search button, you can view the heat map report.
363
Figure 4-216
4.10.3 Voice
Note
This function is for some series product only.
The audio function is to manage audio files and set schedule play function. It is to realize audio broadcast
activation function.
4.10.3.1.1 File Manage
Here you can add audio file, listen to the audio file, or rename/delete audio file. Here you can also set
audio volume. See Figure 4-217.
364
Figure 4-217
Click Add button, you can add audio file and import the audio file via the USB device. The audio file
format shall be MP3 or PCM. See Figure 4-218.
Important
The audio file shall be saved on the USB device. You need to connect the USB device all the time;
otherwise, the audio link function may fail. So, if you want to use the audio trigger function,
please make sure the audio file is on the UBS device and the USB device has connected to the
NVR before the NVR boots up. You need to make sure the USB device connection is always there
if you want to manage and use the audio file function.
365
Figure 4-218
4.10.3.1.2 Schedule
It is to set schedule broadcast function. You can play the different audio files in the specified periods. See
Figure 4-219.
Figure 4-219
4.10.4 RS232
366
From Main menu->Setting->System->RS232, RS232 interface is shown as below. There are five items.
See Figure 4-220.
 Function: There are various devices for you to select. Console is for you to use the COM or mini-end
software to upgrade or debug the program. The control keyboard is for you to control the device via
the special keyboard. Transparent COM (adapter) is to connect to the PC to transfer data directly.
Protocol COM is for card overlay function. Network keyboard is for you to use the special keyboard
to control the device. PTZ matrix is to connect to the peripheral matrix control.
 Baud rate: You can select proper baud rate.
 Data bit: You can select proper data bit. The value ranges from 5 to 8.
 Stop bit: There are three values: 1/1.5/2.
 Parity: there are five choices: none/odd/even/space mark.
System default setup is:
 Function: Console
 Baud rate:115200
 Data bit:8
 Stop bit:1
 Parity: None
After completing all the setups please click save button, system goes back to the previous menu.
Figure 4-220
4.10.5 POS
Connect the device with the POS, the device can receive the POS information and overlay corresponding
info on the video.
Note
367


For the local-end, this function supports one-window display and playback only.
This function is for the cashier of the supermarket and etc. The device can get the information from
the POS and then overlay the txt information on the video.
Step 1 From main menu->Setting->System->POS, the interface is shown as below. See Figure 4-221.
Figure 4-221
Step 2
Step 3
Click Add button, the interface is shown as below. See Figure 4-222.
Set parameters.
 Enable: Check the box to enable POS function.
 Name: Input POS name. System max supports 63 English letters.
 Connection type: This is for net mode only. Click Setup button, you can set source IP (POS
IP address), port is the POS port. Destination IP is the NVR default Ethernet card IP, port is the
POS port (read-only). See Figure 4-223.
 Network time out: If there is a network problem, NVR can wait for the specified time you set
here to send out the POS information. Once the network time is out, NVR only send out current
valid POS information when then network resumes normal.
 Time display: It is to set the POS information displayed time on the video. If you set 5
seconds, then the POS information appears after 5 seconds display.
 Channel Set: Click it to go to Figure 2-18. Select a channel you want to overlay POS
information and then click Save button
368
Figure 4-222
Step 4
In Figure 4-222, click the Enable box to enable POS function and then input POS device name.
Note
 The POS device name shall be unique.
 POS device name max supports 63-digit.
Step 5 Click Setup button after the connection type, the interface is shown as in Figure 4-223.
Step 6 Set source IP (POS device IP address) and destination IP (NVR IP address).
Figure 4-223
369
Step 7
In Figure 4-222, click Channel setup button, select a channel you want to overlay POS
information and then click Save button. See Figure 4-224.
Note
In Figure 4-221, click
to change setup, click
to delete POS setup.
Figure 4-224
4.10.6 Broadcast
It is to broadcast to the camera, or broadcast to a channel group.
Step 1 From Mani menu->Setting->System->Broadcast.
Enter the following interface. See Figure 4-225.
370
Figure 4-225
Step 2
Click Add group.
Enter add group interface. See Figure 4-226.
Figure 4-226
Step 3
Input group name and select one or more channels.
371
Step 4
Click Save button to complete broadcast group setup.
Note
On the broadcast interface, click
to change group setup, click
After complete broadcast setup, on the preview interface and then click
to delete group.
on the navigation
bar, device pops up broadcast diaologue box. Select a group name and then click
begin broadcast. See Figure 4-227.
to
Figure 4-227
4.10.7 Auto Maintain
Here you can set auto-reboot time and auto-delete old files setup. You can set to delete the files for the
specified days. See Figure 4-228.
You can select proper setup from dropdown list.
After all the setups please click save button, system goes back to the previous menu.
372
Figure 4-228
4.10.8 Backup
4.10.8.1 File Backup
In this interface, you can backup record file to the USB device.
a) Connect USB burner, USB device or portable HDD and etc to the device.
b) From Main menu->Backup, you can go to the Backup interface. See Figure 4-229
Figure 4-229
373
c) Select backup device and then set channel, file start time and end time.
d) Click add button, system begins search. All matched files are listed below. System automatically
calculates the capacity needed and remained. See Figure 4-230.
e) System only backup files with a √ before channel name. You can use Fn or cancel button to
delete √ after file serial number.
f) Click backup button, you can backup selected files. There is a process bar for you reference.
g) When the system completes backup, you can see a dialogue box prompting successful backup.
Figure 4-230
h) Click backup button, system begins burning. At the same time, the backup button becomes stop
button. You can view the remaining time and process bar at the left bottom.
Note
 During backup process, you can click ESC to exit current interface for other operation (For
some series product only). The system will not terminate backup process.
 The file name format usually is: Channel number+Record type+Time. In the file name, the
YDM format is Y+M+D+H+M+S. File extension name is .dav.
4.10.8.2 Import/Export
This function allows you to copy current system configuration to other devices. It also supports import,
create new folder, and delete folder and etc function.
From Main menu->Setting->System->Import/Export, you can see the configuration file backup interface is
shown as below. See Figure 4-231.
374
Figure 4-231



Export: Please connect the peripheral device first and then go to the following interface. Click
Export button, you can see there is a corresponding “Config_Time” folder. Double click the folder,
you can view some backup files.
Import: Here you can import the configuration files from the peripheral device to current device. You
need to select a folder first. You can see a dialogue box asking you to select a folder if you are
selecting a file. System pops up a dialogue box if there is no configuration file under current folder.
After successfully import, system needs to reboot to activate new setup.
Format: Click Format button, system pops up a dialogue box for you to confirm current operation.
System begins format process after you click the OK button.
Note:
 System cannot open config backup interface again if there is backup operation in the process.
 System refreshes device when you go to the config backup every time and set current directory as
the root directory of the peripheral device.
 If you go to the configuration backup interface first and then insert the peripheral device, please click
Refresh button to see the newly added device.
4.10.8.3 Backup Log
a) From Main menu->Info->Log, the interface is shown as below. See Figure 4-232.
375
Figure 4-232
b) Select log type and then set start time/end time, click Search button, you can see log time and
event information. Click
to view detailed log information.
c) Select log items you want to save and then click backup button, you can select a folder to save
them. Click Start to backup and you can see the corresponding dialogue box after the process is
finish.
4.10.8.4 USB Device Auto Pop-up
After you inserted the USB device, system can auto detect it and pop up the following dialogue box. It
allows you to conveniently backup file, log, configuration or update system. See Figure 4-233. Please
refer to chapter 4.10.8.1 file backup, chapter 4.10.8.3 backup log, chapter 4.10.8.2 import/export, and
chapter 4.6.2 search for detailed information.
376
Figure 4-233
4.10.9 Default
You can restore factory default setup to fix some problems when the device is running slowly.
Configuration error occurred.
From Main menu->Setting->System->Default, you can go to the default interface. See Figure 4-234.
Click default icon, system pops up a dialogue box. You can highlight






to restore factory default setup.
All
Camera
Network
Event
Storage
System
Please highlight icon
to select the corresponding function.
After all the setups please click OK button, system goes back to the previous menu.
Warning!
After you use default function, some your customized setup may lose forever! Please think twice before
you begin the operation!
377
Figure 4-234
4.10.10Update
4.10.10.1 Local Update
From Mani menu->Setting->Info->Update, you can go to the following interface. See Figure 4-235.
a) Insert USB device that contain the upgrade file.
b) Click Start button and then select the .bin file.
c) You can see the corresponding dialogue box after the update process is complete.
378
Figure 4-235
4.10.10.2 Uboot
When device is booting up, it can auto detect the USB device and the update file on it. It can auto update
once there is proper upgrade file.
Important



USB device root directory shall have “u-boot.bin.img” and “update.img” files. USB device shall be
FAT32 mode.
For 4X series product, it only updates “update.img”. The “update.img” shall be renamed as
“recovery.img” and is saved on the root directory.
USB device shall be on the USB 2.0 port, otherwise device cannot detect or update.
4.11 Logout /Shutdown/Restart
From Mani menu->Operation->Shutdown, you can see an interface shown as in Figure 4-236.
 Shutdown: System shuts down and turns off power.
 Logout: Log out menu. You need to input password when you login the next time.
 Restart: reboot device.
If you shut down the device, there is a process bar for your reference, system waits for 3 seconds and
then shut down (You cannot cancel).
Please note, sometimes you need to input the proper password to shut down the device.
379
Figure 4-236
380
5 Web Operation
5.1 General Introduction
If it is your first time to login the device, please initialize your device first. Refer to chapter 5.2 Device
Initialization for detailed information.
The device web provides channel monitor menu tree, search, alarm setup, system setup, PTZ control and
monitor window and etc.
Note



Slight difference may be found on user interface. Please refer to the actual product for detailed
information.
Device supports various browsers such as Safari, Chrome and etc.
Use ChromeApp to login the WEB if the Chrome version is 45 or higher. Go to the Chrome online
store to download the ChromeApp installation package.
5.1.1 Preparation
Step 1
Step 2
PC and NVR connection is OK.
Set PC IP address, NVR IP address, subnet mask and gateway.
 Set the IP address of the same section for the PC and NVR. Input corresponding gateway
and subnet mask if there are routers.)
 The device default IP address is 192.168.1.108.
Step 3 Check the PC and device connection is OK or not. Refer to the following two ways to check the
network connection is OK or not. When the PC and device network connection is OK, login the
WEB via the PC.
 On PC, use order ping ***.***.***.***(NVR IP address) to check connection is OK or not.
Login Usually the TTL value is 255.
 Login the device local menu, from setting->Network->Network test and then input PC IP
address. Check the connection is OK or not.
Step 4 Login the WEB. Refer to chapter 5.9 Login for detailed information.
5.2 Device Initialization
If it is your first time to use the device, please set a login password of admin (system default user).
Note
For your device safety, please keep your login password of admin well after the initialization steps, and
change the password regularly.
Please follow the steps listed below.
Step 1 Open the IE and then input the NVR IP address in the address column.
Step 2 Click Enter button.
Device displays device initialization interface. See Figure 5-1.
381
Figure 5-1
Step 3


Set login password of admin.
User name: The default user name is admin.
Password/confirm password: The password ranges from 8 to 32 digitals. It can contain letters,
numbers and special characters (excluding “'”,“"”,“;”,“:”,“&”) . The password shall
contain at least two categories. Usually we recommend the strong password.
WARNING
Step 4
STRONG PASSWORD RECOMMENDED-For your device own safety, please create a
strong password of your own choosing. We also recommend you change your password
periodically especially in the high security system.
Click Next, device goes to the following interface. See Figure 5-2.
382
Figure 5-2
Step 5
Set security questions.
Note




After setting the security questions here, you can use the email you input here or answer the
security questions to reset admin password Refer to chapter 5.3 Reset password for detailed
information.
Cancel the email or security questions box and then click Next button to skip this step.
Email: Input an email address for reset password purpose. Scan the QR code to reset the
password, you need to receive the security code by the email. Input the security code to reset
the password of admin. In case you have not input email address here or you need to update
the email information, please go to the main Setup->System->Account to set. Refer to chapter
5.10.5.7 for detailed information.
Security question: Set security questions and corresponding answers. Properly answer the
questions to reset admin password. In case you have not input security question here or you
need to update the security question information, please go to the main
menu->Setting->System->Account->Security question to set. Refer to chapter 4.10.1.1.5
Security question for detailed information.
Note
Step 6
If you want to reset password by answering security questions, please go to the local menu
interface.
Click OK to complete the device initialization setup. See Figure 5-3.
383
Figure 5-3
5.2.1 Log in
Open the IE and then input the NVR IP address in the address column.
For example, if your NVR IP address is 192.168.1.108, then please input http:// 192.168.1.108 in IE
address column. See Figure 5-4.
Input
IP
address here.
Figure 5-4
System pops up warning information to ask you whether install Web plug-in or not. Please click yes
button.
After installation, the interface is shown as below. See Figure 5-5.
384
Figure 5-5
Please input your user name and password.
Factory default user name is admin and password is what you set in chapter 5.2 Device initialization.
5.3 Reset Password
If you forgot admin password, you can reset the password by email or by answering the security
questions (local menu only).
Please follow the steps listed below.
Step 1 Go to the device login interface. See Figure 5-3.
Step 2
Figure 5-6
Click Forgot password, enter the following interface. See Figure 5-7.
385
Step 3
Step 4
Figure 5-7
Follow the prompts on the interface and then scan the QR code to get the security code.
WARNING

Step 5
Step 6
For the same QR code, max scan twice to get two security codes. Refresh the QR code if
you want to get security code again.
 The security code on you email is only valid for 24 hours.
 After five times security code failure, the admin account will be locked for 5 minutes.
Input the security code on the email and then click Next button.
Input new password and then confirm.
WARNING
Step 7
STRONG PASSWORD RECOMMENDED-For your device own safety, please create a
strong password of your own choosing. The password shall be at least 8-digit containing
at least two types of the following categories: letters, numbers and symbols. We also
recommend you change your password periodically especially in the high security
system.
Click OK button to complete the setup.
5.4 LAN Mode
For the LAN mode, after you logged in, you can see the main window. See Figure 5-13.
This main window can be divided into the following sections.
 Section 1: there are six function buttons: Live(chapter 0), setup (chapter 5.10), info (Chapter 5.11),
playback (chapter 5.12), alarm (chapter 5.13), and logout (chapter 5.15).
 Section 2: There are monitor channels successfully connected to the NVR.
Please refer to Figure 5-8 for main stream and extra stream switch information.
386

Figure 5-8
Section 3: Open all. Open all button is to enable/disable all-channel real-time monitor. Here you can
select main stream/sub stream too. See Figure 5-9.
Figure 5-9
 Section 4: Start Talk button.
You can click this button to enable audio talk. Click 【▼】 to select bidirectional talk mode. There are four
options: DEFAULT,G711a,G711u and PCM. See Figure 5-10.
After you enable the bidirectional talk, the Start talk button becomes End Talk button and it becomes
yellow. Please note, if audio input port from the device to the client-end is using the first channel audio
input port. During the bidirectional talk process, system will not encode the audio data from the 1-channel.
Figure 5-10

Section 5: Instant record button. Click it, the button becomes yellow and system begins manual
record. See Figure 5-11. Click it again, system restores previous record mode.
Figure 5-11
 Section 6: Local play button.
The Web can playback the saved (Extension name is dav) files in the PC-end.
Click local play button, system pops up the following interface for you to select local play file. See Figure
5-12.
387
Figure 5-12




Section 7: Zero-channel encoding. Please refer to chapter 5.8 for detailed information.
Section 8: PTZ operation panel. Please refer to chapter 5.6 for detailed information.
Section 9: Image setup and alarm setup. Please refer to chapter 5.7 for detailed information.
Section 10: From the left to the right ,you can see video quality/fluency/ full
screen/1-window/4-window/6-window/8-window/9-window/13-window/16-window/20-window/25-win
dow/36-window.. You can set video fluency and real-time feature priority.
Figure 5-13
5.5 Real-time Monitor
In section 2, left click the channel name you want to view, you can see the corresponding video in current
window.
On the top left corner, you can view device IP(172.11.10.11), channel number(1), network monitor bit
388
stream(2202Kbps) and stream type(M=main stream, S=sub stream). See Figure 5-14.
1
2
3
4
Figure 5-14
On the top right corner, there are six unction buttons. See Figure 5-15.
1
2 3 4
5
Figure 5-15





1: Digital zoom: Click this button and then left drag the mouse in the zone to zoom in. right click
mouse system restores original status.
2: Local record. When you click local record button, the system begins recording and this button
becomes highlighted. You can go to system folder RecordDownload to view the recorded file.
3: Snapshot picture. You can snapshot important video. All images are memorized in system client
folder PictureDownload (default).
4: Audio :Turn on or off audio.(It has no relationship with system audio setup )
5: Close video.
5.6 PTZ
Before PTZ operation, please make sure you have properly set PTZ protocol. (Please refer to chapter
5.10.5.4).
There are eight direction keys. In the middle of the eight direction keys, there is a 3D intelligent
positioning key.
Click 3D intelligent positioning key, system goes back to the single screen mode. Drag the mouse in the
screen to adjust section size. It can realize PTZ automatically.
Please refer to the following sheet for PTZ setup information.
Parameter
Function
Scan



Select Scan from the dropdown list.
Click Set button, you can set scan left and right limit.
Use direction buttons to move the camera to you desired location
and then click left limit button. Then move the camera again and
then click right limit button to set a right limit.
Preset


Select Preset from the dropdown list.
Turn the camera to the corresponding position and Input the
preset value. Click Add button to add a preset.
389
Parameter
Function
Tour




Select Tour from the dropdown list.
Input preset value in the column. Click Add preset button, you
have added one preset in the tour.
Repeat the above procedures you can add more presets in one
tour.
Or you can click delete preset button to remove one preset from
the tour.
Pattern


Select Pattern from the dropdown list.
You can input pattern value and then click Start button to begin
PTZ movement such as zoom, focus, iris, direction and etc. Then
you can click Add button to set one pattern.
Aux


Please input the corresponding aux value here.
You can select one option and then click AUX on or AUX off
button.
Light and
wiper
You can turn on or turn off the light/wiper.
3D Intelligent Positioning
Key
You can click this icon to
display or hide the PTZ
control platform.
Figure 5-16
5.7 Image/Alarm-out
390
Select one monitor channel video and then click Image button in section 9, the interface is shown as
Figure 5-17.
5.7.1 Image
Here you can adjust its brightness, contrast, hue and saturation. (Current channel border becomes
green).
Or you can click Reset button to restore system default setup.
Figure 5-17
5.7.2 Alarm output
Here you can enable or disable the alarm signal of the corresponding port. See Figure 5-18.
Figure 5-18
5.8 Zero-channel Encode
Select a window and then click zero-channel encode button, the interface is shown as below. See Figure
5-19.
391
Figure 5-19
5.9 WAN Login
In WAN mode, after you logged in, the interface is shown as below. See Figure 5-20.
Figure 5-20
Please refer to the following contents for LAN and WAN login difference.
1) In the WAN mode, system opens the main stream of the first channel to monitor by default. The
open/close button on the left pane is null.
2) You can select different channels and different monitor modes at the bottom of the interface. See
392
Figure 5-21.
Figure 5-21
Important
The window display mode and the channel number are by default. For example, for the 16-channel,
the max window split mode is 16.
3) Multiple-channel monitor, system adopts extra stream to monitor by default. Double click one channel,
system switches to single channel and system uses main stream to monitor. You can view there are two
icons at the left top corner of the channel number for you reference. M stands for main stream. S stands
for sub stream (extra stream).
4) If you login via the WAN mode, system does not support alarm activation to open the video function in
the Alarm setup interface.
Important
 For multiple-channel monitor mode, system adopts extra stream to monitor by default. You cannot
modify manually. All channels are trying to synchronize. Please note the synchronization effect still
depends on your network environments.
 For bandwidth consideration, system cannot support monitor and playback at the same time. System
auto closes monitor or playback interface when you are searching setup in the configuration interface.
It is to enhance search speed.
5.10 Setup
5.10.1 Camera
5.10.1.1 Registration
5.10.1.1.1 Registration
From Main menu->Setting->Camera->Registration->Registration, you can see the following interface.
See Figure 5-22.
393
Figure 5-22
Please refer to the following sheet for parameter information.
Parameter
Function
Select IP address or the MAC address from the dropdown list
and then input the corresponding information, click Search
button to view the results.
Search
Click Search button, you can view the searched device
information on the list. It includes device IP address, port, device
name, manufacturer and type.
Uninitialized
Click to search the initialized devices. Select an uninitialized
device and then click the Initialize button to set the account.
Preview
State
Click
to view the preview video of the remote device.
It is to display the device has been initialized or not. That is to
say, the remote device has set the initial account information or
not.
means the remote device has initialized,
means
the remote device has not been intialized.
Add
Modify
Select a device in the list and then click Add button, system can
connect the device automatically and add it to the Added device
list. Or you can double click one item in the list to add a device.
Click
or any device in the Added device list, you can change
the corresponding channel setup.
Delete
Click
, you can delete the remote connection of the
corresponding channel.
394
Parameter
Function
Type
There are two connection types. You can use the network to
connect to the camera or use the WIFI. The
means
current network camera connection mode is general; the
means current network camera mode is hotspot.
Delete
Select a device in the Added device list and then click Delete
button, system can disconnect the device and remove it from the
Added device list.
Manual Add
Click it, the interface is shown as in Figure 5-23. Here you can
add network camera manually.
You can select a channel from the dropdown list (Here only
shows disconnection channel.)
Figure 5-23
Please refer to the following sheet for parameter information.
Parameter
Function
Manufacturer
Please select from the dropdown list.
Note
Different series products may support different manufacturers, please refer
to the actual product.
IP address
Input remote device IP address.
395
Parameter
Function
Input RTSP port of the remote device. The default setup is 554.
RTSP port
Note
Skip this item if the manufacture is private or customize.
Input HTTP port of the remote device. The default setup is 80.
HTTP port
Note
Skip this item if the manufacture is private or customize.
TCP port
Input TCP port of the remote device. The default setup is 37777.
User
name/password
The user name and password to login the remote device.
Input channel amount or click the Connect button to get the channel amount
of the remote device.
Note
Channel No.
We recommend click Connect button to get remote device channel amount,
the manual add operation may result in failure if the input channel amount is
not right.
Remote
channel No.
After getting the remote device channel amount, click Setup to select a
channel.
Note
Click to select one or more remote channel numbers here.
Channel
The local channel number you want to add. One channel name has
corresponding one channel number.
Decode buffer
There are three item: realtime,local, fluent.
There are four items: auto/TCP/UDP/MULTICAST(ONVIF device only)
Note

The default connection mode is TCP if the connection protocol is
private.

There are three items:TCP/UDP/MULTICAST if the connection protocol
is ONVIF.

There are two items: TCP/UDP if the connection protocol is from the
third-party.
Service type
Change IP
On the searched devices list, check one or more device(s) at the same time. Click Modify IP button, you
can see the following interface. See Figure 5-24
Please refer to the following sheet for log parameter information.
Parameter
Function
DHCP
Check the box here, system can auto allocate the IP
address. The IP address, subnet mask, default
gateway are reference only.
396
Parameter
Function
Static
Check the box here, you can set IP address, subnet
mask, default gateway manually.
IP
address/subnet
mask/default gateway
You can input corresponding information here.
User name/password
The account you login the remote device. Please
input here to password verification to change the
remote device password.
Incremental value
When you want to change several IP addresses,
once you input the IP address of the first device, the
IP address of the next device will increase
accordingly. For example, when the incremental
value is 1, if the IP address of the first device is
172.10.3.128, the IP address of the second device
will auto be set as 172.10.3.129.
Note
For the static IP address, system will alert you if there is any IP conflict. If you are changing several IP
addresses at the same time, system auto skip the conflicted IP and auto allocate again according to the
incremental value you set.
Figure 5-24
Export IP
You can export the list of the added devices to your local PC.
Click Export button and then select the saved path. Click OK.
397
You can see “Backup completed ” prompt.
Note
The export file extension name is .CVS. The file contains IP address, port, remote channel No.
manufacturer, user name, password and etc.
Import IP
You can import the added device list to add the device conveniently.
Click Import button, and then select the import file.
Note
If the imported IP is already in the added device list, system pops up dialogue box for you to confirm
overwrite or not.
 Click OK button, the new IP setup can overwrite the old one.
 Click Cancel button, system adds the new IP setup.
Important



You can edit the exported file. Please make sure the file format is the same. Otherwise you can not
import the file again!
System does not support customized protocol import/export.
The import/export function is for the devices of the same language.
5.10.1.1.2 IPC Upgrade
This interface is to upgrade network camera.
From Main menu->Setting->Camera->Registration->IPC upgrade, enter the following interface. See
Figure 5-25.
Click Browse button to select upgrade file. Or you can use filter to select several network cameras at the
same time.
Figure 5-25
5.10.1.2 Image
Note
398
Slight difference may be found since the connected network camera may not be same model.
Here you can view device property information. The setups become valid immediately after you set. See
Figure 5-26.
Figure 5-26
Please refer to the following sheet for detailed information.
Parameter
Function
Channel
Please select a channel from the dropdown list.
Period
It divides one day (24 hours) to two periods. You can set
different hue, brightness, and contrast for different periods.
Hue
It is to adjust monitor video brightness and darkness level. The
default value is 50.
The bigger the value is, the large the contrast between the bright
and dark section is and vice versa.
Brightness
It is to adjust monitor window brightness. The default value is 50.
The larger the number is , the bright the video is. When you
input the value here, the bright section and the dark section of
the video will be adjusted accordingly. You can use this
function when the whole video is too dark or too bright. Please
note the video may become hazy if the value is too high. The
value ranges from 0 to 100.The recommended value ranges
from 40 to 60.
Contrast
It is to adjust monitor window contrast. The value ranges from 0
to 100. The default value is 50.
The larger the number is, the higher the contrast is. You can use
this function when the whole video bright is OK but the contrast
is not proper. Please note the video may become hazy if the
value is too low. If this value is too high, the dark section may
lack brightness while the bright section may over exposure .The
recommended value ranges from 40 to 60.
Saturation
It is to adjust monitor window saturation. The value ranges from
0 to 100. The default value is 50.
399
The larger the number is, the strong the color is. This value has
no effect on the general brightness of the whole video. The
video color may become too strong if the value is too high. For
the grey part of the video, the distortion may occur if the white
balance is not accurate. Please note the video may not be
attractive if the value is too low. The recommended value ranges
from 40 to 60.
Gain
The gain adjust is to set the gain value. The smaller the value is,
the low the noise is. But the brightness is also too low in the dark
environments. It can enhance the video brightness if the value is
high. But the video noise may become too clear.
White level
It is to enhance video effect.
Color mode
It includes several modes such as standard, color. You can
select corresponding color mode here, you can see hue,
brightness, and contrast and etc will adjust accordingly.
Auto Iris
It is to enable/disable auto iris function.
Flip
It is to switch video up and bottom limit.
This function is disabled by default.
Mirror
It is to switch video left and right limit.
This function is disabled by default.
BLC
Mode
BLC
The device auto exposures according to the environments
situation so that the darkest area of the video is cleared
WDR
For the WDR scene, this function can lower the high bright
section and enhance the brightness of the low bright section. So
that you can view these two sections clearly at the same time.
The value ranges from 1 to 100. When you switch the camera
from no-WDR mode to the WDR mode, system may lose several
seconds record video.
Profile
HLC
After you enabled HLC function, the device can lower the
brightness of the brightest section according to the HLC control
level. It can reduce the area of the halo and lower the brightness
of the whole video.
Off
It is to disable the BLC function. Please note this function is
disabled by default.
It is to set the white balance mode. It has effect on the general
hue of the video. This function is on by default.
You can select the different scene mode such as auto, sunny,
cloudy, home, office, night, disable and etc to adjust the video to
the best quality.

Auto: The auto white balance is on. System can auto
compensate the color temperature to make sure the vide
color is proper.

Sunny: The threshold of the white balance is in the sunny
mode.

Night: The threshold of the white balance is in the night
mode.

Customized: You can set the gain of the red/blue channel.
The value reneges from 0 to 100.
400
Day/Night
It is to set device color and the B/W mode switch. The default
setup is auto.

Color: Device outputs the color video.

Auto: Device auto select to output the color or the B/W
video according to the device feature (The general bright of
the video or there is IR light or not.)

B/W: The device outputs the black and white video.

Sensor: It is to set when there is peripheral connected IR
light.
5.10.1.3 Encode
5.10.1.3.1 Encode
The encode interface is shown as below. See Figure 5-27.
Figure 5-27
Please refer to the following sheet for detailed information.
Parameter
Function
Channel
Please select a channel from the dropdown list.
Video enable
Check the box here to enable extra stream video. This item is
enabled by default.
Code stream
type
It includes main stream, motion stream and alarm stream. You
can select different encode frame rates form different recorded
events.
System supports active control frame function (ACF). It allows
you to record in different frame rates.
For example, you can use high frame rate to record important
events, record scheduled event in lower frame rate and it allows
you to set different frame rates for motion detection record and
alarm record.
Compression
The main bit stream supports H.264. The extra stream supports
401
H.264, MJPEG.
Resolution
Frame Rate
Bit Rate
The resolution here refers to the capability of the network
camera.
PAL:1~25f/s;NTSC:1~30f/s.

Main stream: You can set bit rate here to change video
quality. The large the bit rate is, the better the quality is.
Please refer to recommend bit rate for the detailed
information.

Extra stream: In CBR, the bit rate here is the max value.
In dynamic video, system needs to low frame rate or
video quality to guarantee the value. The value is null in
VBR mode.
Reference bit
rate
Recommended bit rate value according to the resolution and
frame rate you have set.
I Frame
Here you can set the P frame amount between two I frames. The
value ranges from 1 to 150. Default value is 50.
Recommended value is frame rate *2.
Enable audio
Check the box to enable audio function.
The audio of the main stream is enabled by default. When this
function is enabled, the record file has audio/video composite
stream. For the sub stream, please check the video first and
then enable audio.
Watermark
enable
This function allows you to verify the video is tampered or not.
Here you can select watermark bit stream, watermark mode and
watermark character. Default character is DigitalCCTV. The max
length is 85-digit. The character can only include number,
character and underline.
5.10.1.3.2 Snapshot
The snapshot interface is shown as in Figure 5-28.
Figure 5-28
Please refer to the following sheet for detailed information.
Parameter
Function
Snapshot type
There are two modes: Regular (schedule) and Trigger.
 Regular snapshot is valid during the specified period you
set.
 Trigger snapshot only is valid when motion detect alarm,
tampering alarm or local activation alarm occurs.
402
Image size
It is the same with the resolution of the main stream.
Quality
It is to set the image quality. There are six levels.
Interval
It is to set snapshot frequency. The value ranges from 1s to 7s.
Or you can set customized value. The max setup is
3600s/picture.
Click it; you can copy current channel setup to other channel(s).
Copy
5.10.1.3.3 Video Overlay
The video overlay interface is shown as in Figure 5-29.
Figure 5-29
Please refer to the following sheet for detailed information.
Parameter
Function
Cover-area
Check Preview or Monitor first.
Click Set button, you can privacy mask the specified video in the
preview or monitor video.
System max supports 4 privacy mask zones.
You can enable this function so that system overlays time
information in video window.
You can use the mouse to drag the time title position.
You can view time title on the live video of the WEB or the
playback video.
You can enable this function so that system overlays channel
information in video window.
You can use the mouse to drag the channel title position.
You can view channel title on the live video of the WEB or the
playback video.
Time Title
Channel Title
5.10.1.3.4 Path
The storage path interface is shown as in Figure 5-30.
403
Here you can set snap image saved path (
(
in the preview interface) and the record storage path
in the preview interface).The default setup is C:\PictureDownload and C:\RecordDownload.
Please click the Save button to save current setup.
Figure 5-30
5.10.1.4 Channel Name
Here you can set channel name. See Figure 5-31.
Figure 5-31
5.10.2 Network
5.10.2.1 TCP/IP
The TCP/IP interface is shown as in Figure 5-32.
404
Figure 5-32
Please refer to the following sheet for detailed information.
Parameter
Function
Mode
There are two modes: static mode and the DHCP mode.

The IP/submask/gateway are null when you select the
DHCP mode to auto search the IP.

If you select the static mode, you need to set the
IP/submask/gateway manually.

If you select the DHCP mode, you can view the
IP/submask/gateway from the DHCP.

If you switch from the DHCP mode to the static mode, you
need to reset the IP parameters.

Besides, IP/submask/gateway and DHCP are read-only
when the PPPoE dial is OK.
Mac Address
It is to display host Mac address.
IP Version
It is to select IP version. IPV4 or IPV6.
You can access the IP address of these two versions.
IP Address
Please use the keyboard to input the corresponding number to
modify the IP address and then set the corresponding subnet
mask and the default gateway.
Preferred DNS
DNS IP address.
Alternate DNS
Alternate DNS IP address.
For the IP address of IPv6 version, default gateway, preferred DNS and
alternate DNS, the input value shall be 128-digit. It shall not be left in blank.
LAN load
System can process the downloaded data first if you enable this
function. The download speed is 1.5X or 2.0X of the normal
speed.
405
5.10.2.2 Connection
The connection interface is shown as in Figure 5-33.
Figure 5-33
Please refer to the following sheet for detailed information.
Parameter
Function
Max connection
The max client login amount (such as WEB, platform, cellphone
and etc). The value ranges from 1 to 128(default).
TCP port
The default value is 37777. You can input the actual port
number if necessary.
UDP port
The default value is 37778. You can input the actual port
number if necessary.
HTTP port
The default value is 80. You can input the actual port number if
necessary.
HTTPS
The default value is 443. You can input the actual port number if
necessary.
RTSP port
The default value is 554.
5.10.2.3 WIFI AP
Please note this function is for some series only.
5.10.2.3.1 General Setup
The WIFI AP interface is shown as in Figure 5-34. Here you can set WIFI hotspot, so that the network
camera can use the hotspot to connect to the network.
406
Figure 5-34
Please refer to the following sheet for detailed information.
Parameter
Function
SSID
It is to set SSID name. You can use this name to search the
device.
Password
It is to set SSID password. You can use this password to
connect to the network.
Security
Select authentication from the dropdown list.
Start IP/End IP
Input start IP and end IP. The NVR can allocate the IP address
in the range you specified here.
WPS
Click WPS button to enable WPS function. After the network
camera enabled this function, it can automatically connect to the
network.
Remote device
In the list, you can view the network camera(s) that connected
to the NVR. It includes signal intensity, IP, MAC address, bit
rate, channel number, type, status and etc.
5.10.2.3.2 Advanced
Click Advanced button, the interface is shown as below. See Figure 5-35.
407
Figure 5-35
Please refer to the following sheet for detailed information.
Parameter
Function
IPv4 address
Input WIFI AP IP address.
IPv4 netmask
Input WIFI AP network mask.
IPv4 gateway
Input WIFI AP gateway.
Start IP/End IP
Input start IP and end IP. The NVR can allocate the IP address
in the range you specified here.
Upgrade
Click it to upgrade WIFI AP module.
5.10.2.4 WIFI
Please note this function is for the device of WIFI module.
The WIFI interface is shown as in Figure 5-36.
Figure 5-36
408
Please check the box to enable WIFI function and then click the Search SSID button. Now you can view
all the wireless network information in the following list. Double click a name to connect to it. Click
Refresh button, you can view latest connection status.
5.10.2.5 3G
5.10.2.5.1 CDMA/GPRS
The CDMA/GPRS interface is shown as in Figure 5-37.
Figure 5-37
Please refer to the following sheet for detailed information.
Parameter
Function
WLAN type
Here you can select 3G network type to distinguish the 3G
module from different ISP. The types include WCDMA,
CDMA1x and etc.
APN/Dial No.
Here is the important parameter of PPP.
Authorization
It includes PAP,CHAP,NO_AUTH.
Pulse interval
It is to set time to end 3G connection after you close extra
stream monitor. For example, if you input 60 here, system ends
3G connection after you close extra stream monitor 60 seconds.
Important

If the pulse interval is 0, then system does not end 3G connection after
you close the extra stream monitor.

Pulse interval here is for extra stream only. This item is null if you are
using main stream to monitor.
5.10.2.5.2 Mobile
The mobile setup interface is shown as in Figure 5-38.
Here you can activate (send out “on”) or turn off (Send out “off”) the 3G connected phone or mobile phone,
409
or the phone you set to get alarm message.
Check send SMS box and then input the phone number in the receiver column. Click
to add one
receiver. Repeat the above steps you can add more phones. Select a phone number and then click
,
you can delete it. Click OK button to complete the setup.
Figure 5-38
5.10.2.6 PPPoE
The PPPoE interface is shown as in Figure 5-39.
Input the PPPoE user name and password you get from the IPS (internet service provider) and enable
PPPoE function. Please save current setup and then reboot the device to get the setup activated.
Device connects to the internet via PPPoE after reboot. You can get the IP address in the WAN from the
IP address column.
Please note, you need to use previous IP address in the LAN to login the device. Please go to the
IP address item to via the device current device information. You can access the client-end via
this new address.
410
Figure 5-39
5.10.2.7 DDNS
The DDNS interface is shown as in Figure 5-40.
The DDNS is to set to connect the various servers so that you can access the system via the server.
Please go to the corresponding service website to apply a domain name and then access the system via
the domain. It works even your IP address has changed.
Please select DDNS from the dropdown list (Multiple choices). Before you use this function, please make
sure your purchased device support current function.
Figure 5-40
Please refer to the following sheet for detailed information.
Parameter
Function
Server Type
You can select DDNS protocol from the dropdown list and then
enable DDNS function.
Server IP
DDNS server IP address
Server Port
DDNS server port.
Domain Name
Your self-defined domain name.
411
Parameter
Function
User
The user name you input to log in the server.
Password
The password you input to log in the server.
Update period
Device sends out alive signal to the server regularly.
You can set interval value between the device and DDNS server
here.
Quick DDNS and Client-end Introduction
1) Background Introduction
Device IP is not fixed if you use ADSL to login the network. The DDNS function allows you to access the
NVR via the registered domain name. Besides the general DDNS, the quick DDNS works with the device
from the manufacturer so that it can add the extension function.
2) Function Introduction
The quick DDNS client has the same function as other DDNS client end. It realizes the bonding of the
domain name and the IP address. Right now, current DDNS server is for our own devices only. You need
to refresh the bonding relationship of the domain and the IP regularly. There is no user name, password
or the ID registration on the server. At the same time, each device has a default domain name (Generated
by MAC address) for your option. You can also use customized valid domain name (has not registered.).
3) Operation
Before you use Quick DDNS, you need to enable this service and set proper server address, port value
and domain name.

Server address:www.quickddns.com

Port number:80

Domain name:There are two modes: Default domain name and customized domain name.
Except default domain name registration, you can also use customized domain name (You can input your
self-defined domain name.) After successful registration, you can use domain name to login installed of
the device IP.

User name: It is optional. You can input your commonly used email address.
Important
 Do not register frequently. The interval between two registrations shall be more than 60 seconds. Too
many registration requests may result in server attack.
 System may take back the domain name that is idle for one year. You can get a notification email
before the cancel operation if your email address setup is OK.
5.10.2.8 IP filter
The IP filter interface is shown as in Figure 5-41.
After you enabled trusted sites function, only the IP listed below can access current NVR.
If you enable blocked sites function, the following listed IP addresses cannot access current NVR.
412
Figure 5-41
5.10.2.9 Email
The email interface is shown as in Figure 5-42.
Figure 5-42
Please refer to the following sheet for detailed information.
Parameter
Function
Enable
Please check the box here to enable email function.
SMTP Server
Input server address and then enable this function.
Port
Default value is 25. You can modify it if necessary.
413
Parameter
Function
Anonymity
For the server supports the anonymity function. You can auto
login anonymously. You do not need to input the user name.
password and the sender information.
User Name
The user name of the sender email account.
Password
The password of sender email account.
Sender
Sender email address.
Authentication
(Encryption
mode)
You can select SSL or none.
Subject
Input email subject here.
Attachment
System can send out the email of the snapshot picture once
you check the box here.
Receiver
Input receiver email address here. Max three addresses.
It supports SSL, TLS email box.
The send interval ranges from 0 to 3600 seconds. 0 means
there is no interval.
Please note system will not send out the email immediately
when the alarm occurs. When the alarm, motion detection or
the abnormity event activates the email, system sends out the
email according to the interval you specified here. This
function is very useful when there are too many emails
activated by the abnormity events, which may result in heavy
load for the email server.
Please check the box here to enable this function.
Interval
Health mail
enable
Update period
(interval)
Email test
This function allows the system to send out the test email to
check the connection is OK or not.
Please check the box to enable this function and then set the
corresponding interval. The value ranges from 30 minutes to
1440 minutes.
System can send out the email regularly as you set here.
The system will automatically sent out a email once to test the
connection is OK or not .Before the email test, please save the
email setup information.
5.10.2.10 UPnP
It allows you to establish the mapping relationship between the LAN and the public network.
Here you can also add, modify or remove UPnP item. See Figure 5-43.
 In the Windows OS, From Start->Control Panel->Add or remove programs. Click the “Add/Remove
Windows Components” and then select the “Network Services” from the Windows Components
Wizard.
 Click the Details button and then check the “Internet Gateway Device Discovery and Control client”
and “UPnP User Interface”. Please click OK to begin installation.
 Enable UPnP from the Web. If your UPnP is enabled in the Windows OS, the NVR can auto detect it
via the “My Network Places”
414
Figure 5-43
Please refer to the following sheet for detailed information.
Parameter
Function
PAT
Check the corresponding box to enable PAT function.
Status
Display UPnP function status.
Port mapping list
It is corresponding to the UPnP mapping information on the router.
Check the box before the service name to enable current PAT service.
Otherwise, the service is null.

Service name:Customized name.

Protocol:Protocol type.

Internal port:The port mapped to the port.

External port:The port current device needs to map.

Device has three mapping items: HTTP/TCP/UDP.
Note
When you set the external port (outport) of the router, the value ranges
from 1024 to 5000. Do not use port 1~255 or system port 256~1023,
in case there is conflict.
Add
Click Add button to add map relationship.
Note
For the data transmission protocol TCP/UDP, the external port and the
internal port shall be the same to guarantee proper data transmission.
Delete
Select one service and then click
to delete map relationship.
5.10.2.11 SNMP
The SNMP interface is shown as in Figure 5-44.
The SNMP allows the communication between the network management work station software and the
proxy of the managed device. It is reserved for the 3rd party to develop.
415
Figure 5-44
Please refer to the following sheet for detailed information.
Parameter
Function
SNMP Port
The listening port of the proxy program of the device. It is a
UDP port not a TCP port. The value ranges from 1 to 65535.
The default value is 161
Read Community
It is a string. It is a command between the manage process
and the proxy process. It defined the authentication, access
control and the management relationship between one proxy
and one group of the managers. Please make sure the device
and the proxy are the same.
The read community will read all the objects the SNMP
supported in the specified name. The default setup is public.
It is a string. It is a command between the manage process
and the proxy process. It defined the authentication, access
control and the management relationship between one proxy
and one group of the managers. Please make sure the device
and the proxy are the same.
The read community will read/write/access all the objects the
SNMP supported in the specified name. The default setup is
write.
The destination address of the Trap information from the proxy
program of the device.
The destination port of the Trap information from the proxy
program of the device. It is for the gateway device and the
client-end PC in the LAN to exchange the information. It is a
non-protocol connection port. It has no effect on the network
applications. It is a UDP port not TCP port. The value ranges
from 1 to 165535. The default value is 162.
 Check V1, system only processes the information of V1.
 Check V2, system only processes the information of V2.
Write Community
Trap address
Trap port
SNMP version
5.10.2.12 Multicast
The multicast interface is shown as in Figure 5-45.
Multicast is a transmission mode of data packet. When there is multiple-host to receive the same data
416
packet, multiple-cast is the best option to reduce the broad width and the CPU load. The source host
can just send out one data to transit. This function also depends on the relationship of the group member
and group of the outer.
Figure 5-45
5.10.2.13 Auto Register
The auto register interface is shown as below. See Figure 5-46.
This function allows the device to auto register to the proxy you specified. In this way, you can use the
client-end to access the NVR and etc via the proxy. Here the proxy has a switch function. In the network
service, device supports the server address of IPv4 or domain.
Please follow the steps listed below to use this function.
Please set proxy server address, port, and sub-device name at the device-end. Please enable the auto
register function, the device can auto register to the proxy server.
Figure 5-46
5.10.2.14 Alarm Centre
The alarm center interface is shown as below. See Figure 5-47.
This interface is reserved for you to develop. System can upload alarm signal to the alarm center when
local alarm occurs.
Before you use alarm center, please set server IP, port and etc. When an alarm occurs, system can send
out data as the protocol defined, so the client-end can get the data.
417
Figure 5-47
5.10.2.15 HTTPS
In this interface, you can set to make sure the PC can successfully login via the HTTPS. It is to guarantee
communication data security. The reliable and stable technology can secure the user information security
and device safety. See Figure 5-48.
Note
 You need to implement server certificate again if you have changed device IP.
 You need to download root certificate if it is your first time to use HTTPS on current PC.
Figure 5-48
5.10.2.15.1 Create Server Certificate
If it is your first time to use this function, please follow the steps listed below.
In Figure 5-48, click
button, input country name, state name and etc. Click
Create button. See Figure 5-49.
Note
Please make sure the IP or domain information is the same as your device IP or domain name.
418
Figure 5-49
You can see the corresponding prompt. See Figure 5-50. Now the server certificate is successfully
created.
Figure 5-50
5.10.2.15.2 Download root certificate
In Figure 5-48, click
button, system pops up a dialogue box. See Figure 5-51.
Figure 5-51
Click Open button, you can go to the following interface. See Figure 5-52.
419
Figure 5-52
Click Install certificate button, you can go to certificate wizard. See Figure 5-53.
Figure 5-53
Click Next button to continue. Now you can select a location for the certificate. See Figure 5-54.
420
Figure 5-54
Click Next button, you can see the certificate import process is complete. See Figure 5-55.
Figure 5-55
Click Finish button, you can see system pops up a security warning dialogue box. See Figure 5-56.
Figure 5-56
421
Click Yes button, system pops up the following dialogue box, you can see the certificate download is
complete. See Figure 5-57.
Figure 5-57
5.10.2.15.3 View and set HTTPS port
From Setup->Network->Connection, you can see the following interface. See Figure 5-58.
You can see HTTPS default value is 443.
Figure 5-58
5.10.2.15.4 Login
Open the browser and then input https://xx.xx.xx.xx:port.
xx.xx.xx.xx: is your device IP or domain mane.
Port is your HTTPS port. If you are using default HTTPS value 443, you do not need to add port
information here. You can input https://xx.xx.xx.xx to access.
Now you can see the login interface if your setup is right.
5.10.2.16 P2P
You can use your cell phone to scan the QR code and add it to the cell phone client.
Via the SN from scanning the QR code, you can access the device in the WAN. Please refer to the P2P
operation manual included in the resources CD.
The P2P interface is shown as in Figure 5-59.
Check the Enable box to enable P2P function and then click the Save button. Now you can view the
device status and SN.
422
Figure 5-59
5.10.3 Event
5.10.3.1 Video detect
5.10.3.1.1 Motion Detect
After analysis video, system can generate a video loss alarm when the detected moving signal reached
the sensitivity you set here.
The motion detect interface is shown as in Figure 5-60.
423
Figure 5-60
Figure 5-61
424
Figure 5-62
Figure 5-63
425
Figure 5-64
Figure 5-65
Please refer to the following sheet for detailed information.
Parameter
Function
Enable
You need to check the box to enable motion detection function.
Please select a channel from the dropdown list.
Period
Motion detection function becomes activated in the specified
periods. See Figure 5-61.
There are six periods in one day. Please draw a circle to enable
corresponding period.
Click OK button, system goes back to motion detection interface,
please click save button to exit.
Anti-dither
System only memorizes one event during the anti-dither period.
The value ranges from 5s to 600s.
Sensitivity
There are six levels. The sixth level has the highest sensitivity.
Region
If you select motion detection type, you can click this button to set
motion detection zone. The interface is shown as in Figure 5-62.
Here you can set motion detection zone. There are four zones for
you to set. Please select a zone first and then left drag the mouse
to select a zone. The corresponding color zone displays different
detection zone. You can click Fn button to switch between the arm
mode and disarm mode. In arm mode, you can click the direction
buttons to move the green rectangle to set the motion detection
zone. After you completed the setup, please click ENTER button to
exit current setup. Do remember click save button to save current
426
Parameter
Function
setup. If you click ESC button to exit the region setup interface
system will not save your zone setup.
Record
channel
System auto activates motion detection channel(s) to record once
an alarm occurs. Please note you need to set motion detect record
period and go to Storage-> Schedule to set current channel as
schedule record.
Record Delay
System can delay the record for specified time after alarm ended.
The value ranges from 10s to 300s.
Alarm out
Enable alarm activation function. You need to select alarm output
port so that system can activate corresponding alarm device when
an alarm occurs.
Latch
System can delay the alarm output for specified time after an
alarm ended. The value ranges from 1s to 300s.
Show
message
System can pop up a message to alarm you in the local host
screen if you enabled this function.
Buzzer
Check the box here to enable this function. The buzzer beeps
when an alarm occurs.
Alarm upload
System can upload the alarm signal to the center (Including alarm
center.
Message
When 3G network connection is OK, system can send out a
message when motion detect occurs.
Send Email
If you enabled this function, System can send out an email to alert
you when an alarm occurs.
Tour
You need to click setup button to select tour channel. System
begins 1-wiindow or multiple-window tour display among the
channel(s) you set to record when an alarm occurs. See Figure
5-64.
PTZ
Activation
Here you can set PTZ movement when alarm occurs. Such as go
to preset X. See Figure 5-63.
Snapshot
Click setup button to select snapshot channel. See Figure 5-65.
Video Matrix
This function is for motion detect only. Check the box here to
enable video matrix function. Right now system supports
one-channel tour function. System takes “first come and first
serve” principle to deal with the activated tour. System will process
the new tour when a new alarm occurs after previous alarm ended.
Otherwise it restores the previous output status before the alarm
activation.
5.10.3.1.2 Video Loss
The video loss interface is shown as in Figure 5-66.
Please note video loss does not support anti-dither, sensitivity, region setup. For rest setups, please refer
to chapter 5.10.3.1.1 motion detect for detailed information.
427
Figure 5-66
5.10.3.1.3 Tampering
The tampering interface is shown as in Figure 5-67.
After analysis video, system can generate a tampering alarm when the detected moving signal reached
the sensitivity you set here.
For detailed setups, please refer to chapter 5.10.3.1.1 motion detect for detailed information.
Figure 5-67
5.10.3.1.4 Scene Change
From main window->Setup->Event->Video detect->Scene change, the video diagnosis interface is shown
as in Figure 5-68.
428
Figure 5-68
For detailed setups, please refer to chapter 5.10.3.1.1 motion detect for detailed information.
5.10.3.2 IVS Plan
The smart plan is for the smart network camera. If you do not set a rule here, you cannot use the
intelligent functions in IVS (Chapter 5.10.3.3), Face detection (Chapter 5.10.3.4) and People counting
(Chapter 5.10.3.5) when you are connecting to a smart network camera.
There are two types to realize intelligent analytics function.
Note


Smart network camera supports intelligent functions: Some smart camera supports the intelligent
functions. For NVR, it just displays the intelligent alarm information from the smart network camera
and set or playback the record file.
NVR supports intelligent functions: The connected network camera does not support intelligent video
analytics function. The NVR supports the analytics function.
From main menu->Setup->Event->IVS plan, you can go to the IVS plan interface. See Figure 5-69.
Figure 5-69
429
Select a channel from the dropdown list. Click Add button, you can see an interface shown as below. See
Figure 5-70.
Select a channel from the dropdown list and then set preset. Click Add button and then set the
corresponding rule.
Note
Some smart camera does not need to add the preset. Please refer to the actual product for detailed
information.
Figure 5-70
Click OK button to complete the setup.
Note


The NVR supports general behavior analytics (IVS), human face detection, heat map, and people
counting. Different network camera supports different smart plans. Please refer to the actual product
for detailed information.
The general behavior analytics (IVS) and human face detection function cannot be valid at the same
time. For example, when add the IVS plan to the preset 1, the human face detection icon becomes
grey.
5.10.3.3 IVS (Behavior Analytics) (Optional)
Once the object state has reached the threshold, NVR can trigger an intelligent alarm.
Note

This function is for some series product only. Please refer to the actual product for detailed
information.
 The IVS function and the human face detection function cannot be valid at the same time.
The IVS function environment shall meet the following requirements:
 The object total size shall not be more than 10% of the whole video.
 The object size on the video shall not be more than 10pixels*10 pixels. The abandoned object size
shall be more than 15pixels*15 pixels (CIF resolution). The object width shall not be more than 1/3 of
430




the video height and width. The recommended height is 10% of the video.
The object and the background brightness different shall be more than 10 grey levels.
The object shall remain on the video for more than 2 seconds. The moving distance is larger than its
own width and shall not be smaller than 15pixels (CIF resolution).
The surveillance environment shall not be too complicated. The IVS function is not suitable for the
environment of too many objects or the changing light.
The surveillance environment shall not contain glasses, reflection light from the ground, and water.
Free of tree branches, shadow, mosquito and bugs. Do not use the IVS function in the backlight
environment, avoid direct sunlight.
5.10.3.3.1 Behavior Analytics
From main menu->Setup->Event->Behavior analytics->Behavior analytics, you can go to the Behavior
analytics interface. See Figure 5-71.
Figure 5-71
Please select a channel from the dropdown list
Click
to add a rule. The default setup is tripwire, you can double click the rule type name to modify.
See Figure 5-72.
Figure 5-72
431
Then you can set corresponding parameters.
Click OK button to complete the setup.
5.10.3.3.1.1 Tripwire
From main menu->Setup->Event-> Behavior analytics->Behavior analytics, click
you can see the
following interface. See Figure 5-73.
System generates an alarm once there is any object crossing the tripwire in the specified direction.
Figure 5-73
Check the Tripwire box to enable tripwire function.
Select SN (Line1/2/3/4) and direction, and then input customized rule name.
 Direction: There are three options: A->B, B->A, both. System can generate an alarm once there is
any object crossing in the specified direction.
Now you can draw a rule. Click Draw rule button and then left click mouse to draw a tripwire. The tripwire
can be a direct line, curve or polygon. Right click mouse to complete. See Figure 5-74.
432
Figure 5-74
Click
to draw filter object. See Figure 5-75.
Figure 5-75
Select the blue line and then use mouse to adjust zone size.
Note
Each rule can set two sizes (min size/max size). Once the object is smaller than the min size or larger
than the max size, there is no alarm. Please make sure the max size is larger than the min size.
Click Ok to complete the rule setup.
433
For detailed setups, please refer to chapter 5.10.3.1.1 motion detect for detailed information.
5.10.3.3.1.2
Intrusion (Cross warning zone)
From main menu->Setup->Event-> Behavior analytics->Behavior analytics, click
, and then select rule
type as intrusion, you can see the following interface. See Figure 4-129.
Note:
 System supports customized area shape and amount.
 Support enter/leave/both detection.
 Can detect the moving object operation in the specified zone, customized trigger amount and staying
time.
 Support objects filter function.
Figure 5-76
Check the Intrusion box to enable intrusion function.
Select SN (Area1/2/3/4) and direction, and then input customized rule name.
 Action: System supports two types:appear/cross.
 Direction: There are three options: A->B, B->A, both. System can generate an alarm once there is
any object enter/exit (Or both) the zone.
Now you can draw a rule. Left click mouse to draw a line first and then right click mouse to draw another
line until you draw a rectangle, you can right click mouse to exit.
Click Ok to complete the rule setup.
Click
to draw the zone. See Figure 5-77.
434
Figure 5-77
For detailed setups, please refer to chapter 5.10.3.1.1 motion detect for detailed information.
5.10.3.3.1.3
Abandoned Object Detect
From main menu->Setup->Event-> Behavior analytics->Behavior analytics, click
, and then select rule
type as abandoned object detection, you can see the following interface. See Figure 5-78.
 System supports customized area shape and amount.
 Support duration setup.
 Support objects filter function.
435
Figure 5-78
Check the Object box to enable object detect function.
 Period: System can generate an alarm once the object is in the zone for the specified period.
Click
to draw the rule. See Figure 5-79.
Figure 5-79
Now you can draw a rule. Left click mouse to draw a line, until you draw a rectangle, you can right click
mouse.
Click Ok to complete the rule setup.
436
For detailed setups, please refer to chapter 5.10.3.1.1 motion detect for detailed information.
5.10.3.3.1.4
Missing Object Detect
From main menu->Setup->Event-> Behavior analytics->Behavior analytics, click
, and then select rule
type as missing object detection, you can see the following interface. See Figure 2-7.
 System supports customized area shape and amount.
 Support period setup.
 Support objects filter function.
Figure 5-80
Click
to draw the rule. See Figure 5-81.
Figure 5-81
437
Click Ok to complete the rule setup.
For detailed setups, please refer to chapter 5.10.3.1.1 motion detect for detailed information.
5.10.3.3.1.5
Loitering
From main menu->Setup->Event-> Behavior analytics->Behavior analytics, click
, and then select rule
type as loitering detection, you can see the following interface. See Figure 2-27.
Note
 System supports customized area shape and amount.
 Support duration setup.
 Support objects filter function.

Figure 5-82
Duration: System can generate an alarm once the object is in the zone for the specified period.
Click
to draw the rule.
Click OK to complete the rule setup.
For detailed setups, please refer to chapter 5.10.3.1.1 motion detect for detailed information.
5.10.3.3.1.6
Crowd gathering detection
From main menu->Setup->Event-> Behavior analytics->Behavior analytics, click
, and then select rule
type as crowd gathering estimation, you can see the following interface. See Figure 2-26.
 Customized zone and amount setup.
 Duration setup.
 Sensitivity setup.
 Min gathering zone setup.
438


Figure 5-83
Duration: System can generate an alarm once the object is in the zone for the specified period.
Sensitivity: It is to set alarm sensitivity. The value ranges from 1 to 10.The default setup is 5.
Click
to draw the rule.
Click OK to complete the rule setup.
For detailed setups, please refer to chapter 5.10.3.1.1 motion detect for detailed information.
5.10.3.3.1.7
Fast moving
From main menu->Setup->Event-> Behavior analytics->Behavior analytics, click
, and then select rule
type as fast moving, you can see the following interface. See Figure 2-25.
 Sensitivity: It is to set alarm sensitivity. The value ranges from 1 to 10.The default setup is 5.
439
Figure 5-84
Click
to draw the rule.
Click OK to complete the rule setup.
For detailed setups, please refer to chapter 5.10.3.1.1 motion detect for detailed information.
5.10.3.3.2 Global Config
From main menu->Setup->Event->Behavior analytics->Global, you can go to the global configuration
interface. See Figure 2-32.
 Channel: Please select a channel from the dropdown list.
 Preset: Select a preset you want to set the rule. Please note, you need to add a preset first,
otherwise, you cannot see the preset dropdown list. If there is no preset, you can draw a rule in
current channel.
 Calibration zone:




Click Add area
, you can draw a calibration zone at the left pane of the interface. Select a zone
and then click Delete zone button; you can remove the selected zone.
Select gauge type (vertical/level), you can set the corresponding length. You can draw three tilt
gauges and one horizontal gauge at the left pane of the interface.
Select Width/Height and then click Verify, you can draw a line in the calibration zone, and then you
can see its actual length.
Update preset: Click it to get the latest preset setup.
440
Figure 5-85
5.10.3.4 Face Detect (Optional)
When camera detects human face, system can generate an alarm.
From main menu->Setup->Event->Face detect, the interface is shown as in Figure 5-86.
 Enable face boost: Check the box here, system can enhance the human face display pane.
 Sensitivity: System supports 6 levels. The sixth level has the highest sensitivity.
Figure 5-86
For detailed setups, please refer to chapter 5.10.3.1.1.
5.10.3.5 People Counting
System can calculate the entry/exit people amount in the specified zone. It can generate an alarm when
the amount has exceeded the threshold.
From main menu->Setup->Event->People counting, you can see an interface shown as in Figure 2-38.
441

Channel: Please select a channel from the dropdown list. Check the box to enable people counting
function.
 OSD overlay: Check the box here; you can view the people amount on the surveillance video.
 Direction: It is to set people flow direction. It includes entry/exit.
 Entry No.: It is to set people entry amount. System can generate an alarm once the amount has
exceeded the threshold.
 Exit No.: It is to set people entry amount. System can generate an alarm once the amount has
exceeded the threshold.
 Stranded No.: It is to set people staying amount in the zone. System can generate an alarm once the
amount has exceeded the threshold.
For detailed setups, please refer to chapter 5.10.3.1.1 motion detect for detailed information.
Figure 5-87
5.10.3.6 Heat Map
It is to detect the object activity level in the scene during the specified period.
From main menu->Setup->Event->Heat Map, you can see an interface shown as in Figure 5-88.
For detailed setups, please refer to chapter 5.10.3.1.1 motion detect for detailed information.
442
Figure 5-88
5.10.3.7 Audio Detect (Optional)
System can generate an alarm once it detect the audio input is abnormal or audio volume changes.
From main menu->Setup->Event->Audio detect, you can see an interface shown as in Figure 5-89.
 Input abnormal: Check the box here, system can generate an alarm once the audio input is
abnormal.
 Intensity change: Check the box here, system can generate an alarm once the audio volume
becomes strong.
 Sensitivity: It refers to the audio recognition sensitivity. The higher the value is, the higher the
sensitivity is.
 Threshold: It is to set intensity change threshold. The smaller the value is, the higher the sensitivity
is.
For detailed setups, please refer to chapter 5.10.3.1.1 motion detect for detailed information.
Figure 5-89
443
5.10.3.8 Alarm
Before operation, please make sure you have properly connected alarm devices such as buzzer. The
input mode includes local alarm and network alarm.
5.10.3.8.1 Local Alarm
The local alarm interface is shown as in Figure 5-90. It refers to alarm from the local device.
Figure 5-90
Figure 5-91
444
Figure 5-92
Please refer to the following sheet for detailed information.
Parameter
Function
Enable
You need to check the box to enable this function.
Please select a channel from the dropdown list.
Period
This function becomes activated in the specified periods.
There are six periods in one day. Please draw a circle to
enable corresponding period.
Select date. If you do not select, current setup applies to
today only. You can select all week column to apply to the
whole week.
Click OK button, system goes back to local alarm
interface, please click save button to exit.
Anti-dither
System only memorizes one event during the anti-dither
period. The value ranges from 5s to 600s.
Sensor type
There are two options: NO/NC.
Record channel
System auto activates motion detection channel(s) to
record once an alarm occurs. Please note you need to set
alarm record period and go to Storage-> Schedule to set
445
Parameter
Function
current channel as schedule record.
Record Delay
System can delay the record for specified time after alarm
ended. The value ranges from 10s to 300s.
Alarm out
Enable alarm activation function. You need to select alarm
output port so that system can activate corresponding
alarm device when an alarm occurs.
Latch
System can delay the alarm output for specified time after
an alarm ended. The value ranges from 1s to 300s.
Show message
System can pop up a message to alarm you in the local
host screen if you enabled this function.
Buzzer
Check the box here to enable this function. The buzzer
beeps when an alarm occurs.
Alarm upload
System can upload the alarm signal to the center
(Including alarm center).
Send Email
If you enabled this function, System can send out an email
to alert you when an alarm occurs.
Tour
You need to click setup button to select tour channel.
System begins 1-wiindow or multiple-window tour display
among the channel(s) you set to record when an alarm
occurs. See Figure 5-64.
PTZ Activation
Here you can set PTZ movement when alarm occurs.
Such as go to preset X. See Figure 5-92.
Snapshot
Click setup button to select snapshot channel. See Figure
5-65.
5.10.3.8.2 Net Alarm
The network alarm interface is shown as in Figure 5-93.
Network alarm refers to the alarm signal from the network. System does not anti-dither and sensor type
setup. For setup information, please refer to chapter 5.10.3.8.1.
446
Figure 5-93
5.10.3.8.3 IPC external alarm
The IPC external alarm interface is shown as in Figure 5-94.
Network alarm refers to the alarm signal from the network. System does not anti-dither and sensor type
setup. For setup information, please refer to chapter 5.10.3.8.1.
Figure 5-94
5.10.3.8.4 IPC Offline Alarm
447
The IPC offline alarm interface is shown as in Figure 5-95.
System can generate an alarm once the network camera is offline. For setup information, please refer to
chapter 5.10.3.8.1.
Figure 5-95
5.10.3.9 Abnormality
From main menu->Setup->Event->Abnormality, it includes four types: HDD/Network/User/Device. See
Figure 5-96 through Figure 5-99.
Figure 5-96
448
Figure 5-97
Figure 5-98
449
Figure 5-99
Please refer to the following sheet for detailed information.
Parameter
Function
Event
Type
The abnormal events include:
HDD: No disk, disk error, disk no space;
 Network: Net disconnection, IP conflict, MAC conflict.
 User: Illegal login.
 Device: Temperature is too high, fan speed is abnormal. Please
note this function is for some series product only.
 You can set one or more items here.
 Less than: You can set the minimum percentage value here. The
device can generate an alarm when capacity is not sufficient. This
item is for disk no space type only.
Enable
Check the box here to enable selected function.
Alarm Out
Please select corresponding alarm output channel when an alarm
occurs. You need to check the box to enable this function.
Latch
The alarm output can delay for the specified time after an alarm stops.
The value ranges from 0s to 300s. The default setup is 10 seconds. The
o second means there is no delaying time.
Attempt(s)
It is to set login attempt times. Once the login attempt exceeds the
threshold you set here, current account will be locked. This function is
for illegal login only.
Lock time
It is to set account lock time once its login attempt has exceeded the
threshold you set. This function is for illegal login only.
Show
message
System can pop up a message to alarm you in the local host screen if
you enabled this function.
450
Parameter
Function
Alarm
upload
System can upload the alarm signal to the center (Including alarm
center.
Send
Email
If you enabled this function, System can send out an email to alert you
when an alarm occurs.
Buzzer
Check the box here to enable this function. The buzzer beeps when an
alarm occurs.
Log
Check the box here, system can record the network event alarm log.
5.10.3.10 Alarm Out
The alarm output interface is shown as below. See Figure 5-100
Here you can set alarm output mode: auto/manual/stop.
Figure 5-100
5.10.4 Storage
5.10.4.1 Schedule
In this interfaces, you can add or remove the schedule record setup. See Figure 5-101.
There are four record modes: general (auto), motion detect, alarm and MD&alarm. There are six periods
in one day.
You can view the current time period setup from the color bar.
 Green color stands for the general record/snapshot.
 Yellow color stands for the motion detect record/snapshot..
 Red color stands for the alarm record/snapshot.
 Blue color stands for MD&alarm record/snapshot.
451
Figure 5-101
Figure 5-102
452
Figure 5-103
Please refer to the following sheet for detailed information.
Parameter
Function
Channel
Please select a channel from the dropdown list.
Pre-record
Please input pre-record time here. The value ranges from 0 to 30.
Redundancy
Check the box here to enable redundancy function. Please note this
function is null if there is only one HDD.
Snapshot
Check the box here to enable snapshot function.
Holiday
Check the box here to enable holiday function.
Setup
Click the Setup button, you can set record period. See Figure 5-102.
There are six periods in one day. If you do not check the date at the
bottom of the interface, current setup is for today only.
Please click Save button and then exit.
Copy
Copy function allows you to copy one channel setup to another. After
setting in channel, click Copy button, you can go to interface Figure
5-103. You can see current channel name is grey such as channel 1.
Now you can select the channel you want to paste such as channel
5/6/7. If you want to save current setup of channel 1 to all channels,
you can click the first box “ALL”. Click the OK button to save current
copy setup. Click the OK button in the Encode interface, the copy
function succeeded.
5.10.4.2 HDD Manager
5.10.4.2.1 Local Storage
The local interface is shown as in Figure 5-104. Here you can see HDD information. You can also operate
453
the read-only, read-write, redundancy (if there are more than on HDD) and format operation.
Figure 5-104
5.10.4.2.2 HDD
The HDD interface is to set HDD group. See Figure 5-105.
Figure 5-105
5.10.4.2.3 FTP
The FTP interface is to set FTP information. See Figure 5-106.
Please set the FTP as your remote storage location. System can save record file or snapshot picture to
the FTP once the network is offline or malfunction.
Figure 5-106
5.10.4.3 Record Control
454
The interface is shown as in Figure 5-107.
Figure 5-107
Please refer to the following sheet for detailed information.
Parameter
Function
Channel
Here you can view channel number.
The number displayed here is the max channel amount of your
device.
Status
There are three statuses: schedule, manual and stop.
Schedule
System enables auto record function as you set in record schedule
setup (general, motion detect and alarm).
Manual
It has the highest priority.
Enable corresponding channel to record no matter what period
applied in the record setup.
Stop
Stop current channel record no matter what period applied in the
record setup.
Start all/
stop all
Check the corresponding All button, you can enable or disable all
channels record.
5.10.4.4 RAID Manager
455
Important
Please make sure your purchased product support the RAID function, otherwise you cannot see
the following interface.
5.10.4.4.1 RAID Config
It is for you to manage RAID HDD. It can display RAID name, type, free space, total space, status and etc.
Here you can add/delete RAID HDD.
Click Add button to select RAID type and then select HDDs, click OK button to add. See Figure 5-108.
Figure 5-108
5.10.4.4.2 Hotspare disks
In Figure 5-108, click hotspare button, you can add the hot spare HDD. See Figure 5-109. The type
includes two options:
 Global: It is global hotspare disk. When any RAID becomes degrading, it can replace and build the
RAID.
 Local: It is local hotspare disk. When the specified RAID becomes degrading, it can replace and build
the RAID.
Select a hot spare device and then click Delete button. Click Apply button to delete.
456
Figure 5-109
5.10.4.5 Storage
5.10.4.5.1 Main Stream
The main stream interface is shown as in Figure 5-110. Here you can set corresponding HDD group to
save main stream.
Figure 5-110
5.10.4.5.2 Sub Stream
The sub stream interface is shown as in Figure 5-111.
Here you can set corresponding HDD group to save sub stream.
457
Figure 5-111
5.10.4.5.3 Snapshot
The snapshot interface is shown as in Figure 5-112. Here you can set corresponding HDD group to save
snapshot picture.
Figure 5-112
5.10.5 Setting
5.10.5.1 General
The general interface includes general, date/time and holiday setup.
5.10.5.1.1 General
The general interface is shown as in Figure 5-113.
458
Figure 5-113
Please refer to the following sheet for detailed information.
Parameter
Function
Device ID
It is to set device name.
Device No.
It is device channel number.
Language
You can select the language from the dropdown list.
Please note the device needs to reboot to get the modification
activated.
Video
Standard
This is to display video standard such as PAL.
HDD full
Here is for you to select working mode when current HDD is full while
the next HDD is not empty. There are two options: stop recording or
rewrite old files.
Pack
duration
Here is for you to specify record duration. The value ranges from 1 to
120 minutes. Default value is 60 minutes.
5.10.5.1.2 Date and time
The date and time interface is shown as in Figure 5-114
459
Figure 5-114
Please refer to the following sheet for detailed information.
Parameter
Function
Date format
Here you can select date format from the dropdown list.
Time
Format
There are two options: 24-H and 12-H.
Time zone
The time zone of the device.
System
time
It is to set system time. It becomes valid after you set.
Sync PC
You can click this button to save the system time as your PC current
time.
DST
Here you can set day night save time begin time and end time. You
can set according to the date format or according to the week format.
NTP
You can check the box to enable NTP function.
NTP server
You can set the time server address.
Port
It is to set the time server port.
Interval
It is to set the sync periods between the device and the time server.
5.10.5.1.3 Holiday Setup
Holiday setup interface is shown as in Figure 5-115.
460
Here you can click Add holidays box to add a new holiday and then click Save button to save.
Figure 5-115
5.10.5.2 Display
Display interface includes GUI, TV adjust, Tour and Customized split.
5.10.5.2.1 Display
Here you can set background color and transparency level. See Figure 5-116.
Figure 5-116
Please refer to the following sheet for detailed information.
Parameter
Function
Resolution
There are four options: 1920×1080, 1280×1024(default),
1280×720, 1024×768. Please note the system needs to reboot to
activate current setup.
461
Color mode
Please select from the dropdown list.
Transparency
Here is for you to adjust transparency. The value ranges from 128
to 255.
Time
title/channel
title
Check the box here, you can view system time and channel
number on the monitor video.
Image
enhance
Check the box; you can optimize the margin of the preview video.
Startup
wizard
Once you check the box here, system will go to the startup wizard
directly when the system restarts the next time. Otherwise, it will go
to the login interface.
Navigation
bar
Check the box here, system displays the navigation bar on the
interface.
Original scale
Click the Set button to select a channel, it can restore original scale.
Auto logout
Here is for you to set auto logout interval once login user remains
inactive for a specified time. Value ranges from 0 to 60 minutes. 0
means there is no standby time. After the auto logout, the user
needs to input user name and password to login again.
Display
intelligent
rule(s)
Check the box to enable IVS function, system can display IVS rule
on the preview interface.
5.10.5.2.2 Tour
The tour interface is shown as in Figure 5-117. Here you can set tour interval, split mode, motion detect
tour and alarm tour mode.
Figure 5-117
462
Please refer to the following sheet for detailed information.
Parameter
Function
Enable tour
Check the box here to enable tour function.
Interval
Here is for you to adjust transparency. The value ranges from 5 to
120s. The default setup is 5s.
Here you can set window mode and channel group. System can
support 1/4/8/9/16/25/36-window according to device channel
amount.
Here you can set motion detect tour/alarm tour window mode.
System supports 1/8-window now.
Split
Motion
tour/Alarm
tour
5.10.5.2.3 Custom Split
From main menu->Setup->System->Display->Custom split, the interface is shown as in Figure 5-118.
Here you can set customized split mode.
Note


This function is for some series products. Please refer to the actual product for detailed information.
Device max supports 5 customized videos.
Figure 5-118
Click
and then click
to select basic mode
In regular mode, drag the mouse in the preview frame, you can merge several small windows to one
window so that you can get you desired split mode.
After the setup, the selected window has the red frame.
Select the merging window, the frame is red; you can click
to cancel the merge to restore regular
mode.
Click OK to exit.
5.10.5.3 RS232
The RS232 interface is shown as in Figure 5-119.
463
Figure 5-119
Please refer to the following sheet for detailed information.
Parameter
Function
Protocol
Select the corresponding dome protocol.
Default setup is console.
Select the baud rate.
Default setup is 115200.
Baud Rate
Data Bit
The value ranges from 5 to 8.
Default setup is 8.
Stop bit
There are two options: 1/2.
Default setup is 1.
Parity
There are five options: none/odd/even/space/mark.
Default setup is none.
5.10.5.4 PTZ
The PTZ interface is shown as in Figure 5-120 (Local) and Figure 5-121 (Remote).
Before setup, please check the following connections are right:
 PTZ and decoder connection is right. Decoder address setup is right.
 Decoder A (B) line connects with NVR A (B) line.
Click Save button after you complete setup, you can go back to the monitor interface to control speed
dome.
464
Figure 5-120
Figure 5-121
Please refer to the following sheet for detailed information.
Parameter
Function
Channel
Select speed dome connected channel.
PTZ Type
There are two options: local/remote.
Please select remote type if you are connecting to the network PTZ.
Please select local type if you are using RS485 to the PTZ camera.
Protocol
Select the corresponding dome protocol such as PELCOD.
Address
Set corresponding dome address. Default value is 1. Please note
your setup here shall comply with your dome address; otherwise
you cannot control the speed dome.
Baud
Rate
Select the dome baud rate. Default setup is 9600.
Data Bit
The value ranges from 5 to 8. Default setup is 8. Please set according
to the speed dome dial switch setup.
465
Parameter
Function
Stop bit
The value ranges from 1 to 2. Default setup is 1. Please set according
to the speed dome dial switch setup.
Parity
The options include non/odd/even/space/null. Default setup is none.
Please set according to the speed dome dial switch setup.
5.10.5.5 POS
Connect the NVR to the POS, it can receive the POS information and overlay on the corresponding
record.
Note
POS info overlay and playback function is for 1-window only.
From main menu->Setting->System->POS, you can go to the following interface. See Figure 5-122.
Figure 5-122
Click Add, you can see the following dialogue box. See Figure 5-123.
Figure 5-123
Check the box to enable POS function, Click Set button; you can see the following interface. See Figure
5-124.
466
Figure 5-124
Set source IP and destination IP, and then click OK. System goes back to Figure 5-123.
 Source IP: POS device IP address.
 Destination IP: NVR IP address.
In Figure 5-123, click Channel Set button, select the channel you want to overlay POS information. Click
OK button to complete the setup.
Tips
: Click it to delete POS setup.
: Click it to change setup information.
5.10.5.6 Voice
The audio function is to manage audio files and set schedule play function. It is to realize audio broadcast
activation function.
5.10.5.6.1 File List
From main menu->Setup->System->Voice->File list, here you can add audio file, or delete audio file. See
Figure 5-125.
Figure 5-125
Click Add button, you can add audio file and import the audio file via the local computer. See Figure
5-126.
467
Figure 5-126
5.10.5.6.2 Schedule
It is to set schedule broadcast function. You can play the different audio files in the specified periods.
From main menu->Setup->System->Voice->.Schedule, you can see the following interface. See Figure
5-127.
Figure 5-127
Please refer to the following sheet for detailed information.
Parameter
Function
Period
There are six periods. Check the box to enable current setup.
Repeat
It is to set audio file repeat times in the specified period.
Interval
It is the audio file repeated interval in the specified period.
Output
port
There are two options: MIC (default)/audio. When reuse the MIC port
and bidirectional talk port, the bidirectional port has the higher priority.
Please note some series product does not support audio function.
468
Note
 The audio file end time depends on the audio file size and the interval setup.
 Priority: Bidirectional talk>Event trigger alarm>Trial listening>Audio schedule broadcast.
5.10.5.7 Account
Note:
 For the character in the following user name or the user group name, system max supports 6-digits.
The space in the front or at the end of the string is null. The valid string includes: character, number,
and underline.
 The user amount default setup is 64 and the group amount default setup is 20. The factory default
setup includes two levels: user and admin. You can set the corresponding group and then set the
rights for the respective user in the specified groups.
 User management adopts group/user modes. The user name and the group name shall be unique.
One user shall be included in only one group.
5.10.5.7.1 User name
In this interface you can add/remove user and modify user name. See Figure 5-128.
Figure 5-128
Add user: It is to add a name to group and set the user rights. See Figure 5-129.
There are three default users: admin/888888 and hidden user “default”.
Hidden user “default” is for system interior use only and cannot be deleted. When there is no login user,
hidden user “default” automatically login. You can set some rights such as monitor for this user so that
you can view some channel view without login.
Here you can input the user name and password and then select one group for current user.
Please note the user rights shall not exceed the group right setup.
For convenient setup, please make sure the general user has the lower rights setup than the admin.
469
Figure 5-129
Modify user
It is to modify the user property, belonging group, password and rights. See Figure 5-130.
Modify password
It is to modify the user password. You need to input the old password and then input the new password
twice to confirm the new setup. Please click the OK button to save.
Please note, the password ranges from 1-digit to 6-digit. It shall include the number only. For the user of
the account rights, he can modify the password of other users.
470
Figure 5-130
5.10.5.7.2 Group
The group management interface can add/remove group, modify group password and etc.
The interface is shown as in Figure 5-131.
Figure 5-131
Add group: It is to add group and set its corresponding rights. See Figure 5-132.
Please input the group name and then check the box to select the corresponding rights. It includes:
shutdown/reboot device, live view, record control, PTZ control and etc.
471
Figure 5-132
Modify group
Click the modify group button, you can see an interface is shown as in Figure 5-133.
Here you can modify group information such as remarks and rights.
Figure 5-133
5.10.5.7.3 ONVIF User
When the camera from the third party is connected with the NVR via the ONVIF user, please use the
verified ONVIF account to connect to the NVR. From main menu->Setting->System->Account->ONVIF
472
User, you can go to ONVIF user interface See Figure 5-134.
Figure 5-134
Click Add user button, you can see the following interface. See Figure 5-135.
Figure 5-135
Please set user name, password and then select group from the dropdown list.
Click Save to complete setup.
Tips
Click
to change user information, click
to delete current user.
5.10.5.8 Auto maintain
The auto maintain interface is shown as in Figure 5-136.
Here you can select auto reboot and auto delete old files interval from the dropdown list.
If you want to use the auto delete old files function, you need to set the file period.
Click Manual reboot button, you can restart device manually.
473
Figure 5-136
5.10.5.9 Import/Export
The interface is shown as in Figure 5-137. This interface is for you to export or import the configuration
files.
Figure 5-137
Please refer to the following sheet for detailed information.
Parameter
Function
Browse
Click to select import file.
Import
It is to import the local setup files to the system.
Export
It is to export the corresponding WEB setup to your local PC.
5.10.5.10 Default
The default setup interface is shown as in Figure 5-138.
Here you can select Network/Event/Storage/Setting/Camera. Or you can check the All box to select all
items.
474
Figure 5-138
5.10.5.11 Upgrade
The upgrade interface is shown as in Figure 5-139.
Please select the upgrade file and then click the update button to begin update. Please note the file name
shall be as *.bin. During the upgrade process, do not unplug the power cable, network cable, or shutdown
the device.
Important
Improper upgrade program may result in device malfunction! Please make sure the operation is
operated under the supervision of the professional engineer!
Figure 5-139
5.11 Information
5.11.1 Version
The version interface is shown as in Figure 5-140.
Here you can view record channel, alarm input/output information, software version, release date and etc.
Please note the following information is for reference only.
475
Figure 5-140
5.11.2 Log
Here you can view system log. See Figure 5-141.
Figure 5-141
Please refer to the following sheet for log parameter information.
Parameter
Function
Type
Log types include: system operation, configuration operation, data
operation, event operation, record operation, user management, log
clear.
Start time
Set the start time of the requested log.
End time
Set the end time of the requested log.
476
Parameter
Function
Search
You can select log type from the drop down list and then click search
button to view the list.
You can click the stop button to terminate current search operation.
Detailed
information
You can select one item to view the detailed information.
Clear
You can click this button to delete all displayed log files. Please
note system does not support clear by type.
Backup
You can click this button to backup log files to current PC.
5.11.3 Online User
The online user interface is shown as in Figure 5-142.
Figure 5-142
5.11.4 People Counting
From main menu->Info->People counting, the interface is shown as in Figure 5-143.
Figure 5-143
477
5.11.5 Heat Map
From main menu->Info->Heat Map, the interface is shown as in Figure 5-144.
Figure 5-144
5.11.6 HDD
From main menu->Info->HDD, the HDD interface is shown as in Figure 5-145. Here you can view HDD
information.
Figure 5-145
5.12 Playback
Click Playback button, you can see an interface is shown as in Figure 5-146.
478
Figure 5-146
5.12.1 Search Record
Please set record type, record date, window display mode and channel name.
 Select Date
You can click the date on the right pane to select the date. The green highlighted date is system current
date and the blue highlighted date means it has record files.
 Window Split
Select window split mode. Click
to display in full screen. Click ESC button to exit. See Figure 5-147.
Figure 5-147
 Select Channel
1~4 means main stream and A1~A4 means sub stream.
 Select Record Type
Check the corresponding box to select record type. See Figure 5-148.
Figure 5-148
5.12.2 File List
Click File list button, you can see the corresponding files in the list. See Figure 5-149.
479
Figure 5-149
5.12.3 Playback
Select a file you want to play and then click Play button, system can begin playback. You can select to
playback in full-screen. Please note for one channel, system cannot playback and download at the same
time. You can use the playback control bar to implement various operations such as play, pause, stop,
slow play, fast play and etc. See Figure 5-150.
Figure 5-150
5.12.4 Download
Select the file(s) you want to download and then click download button, you can see an interface shown
as in Figure 5-151. The Download button becomes Stop button and there is a process bar for your
480
reference. Please go to you default file saved path to view the files.
Figure 5-151
5.12.5 Load more
It is for you to search record or picture. You can select record channel, record type and record time to
download. Or you can use watermark function to verify file.
5.12.5.1 Download By File
Select channel, record type, bit stream type and then input start time and end time. Click Search button,
the download by file interface is shown as in Figure 5-152.
Figure 5-152
Check the file(s) you want to download and there are two options for you to save the file(s).
 Download to local
481
Click Download to local, system pops up the following interface for you to set record format and saved
path. See Figure 5-153.
Figure 5-153
You can click OK to download and view the download process. After the download operation, you can see
corresponding dialog box.
 Download to USB
Connect the corresponding p peripheral device, and then click Download to USB button, you can see the
following interface. See Figure 5-154.
Figure 5-154
Select Backup device and backup type first and then click Start backup button.
After the download operation, you can see corresponding dialogue box.
5.12.5.2 Download by Time
Select channel, bit stream type, start time and end time.
Click Download to Local button, you can see download by time interface is shown as in Figure 5-155.
482
Figure 5-155
Set record format and saved path, you can click OK to download and view the download process. After
the download operation, you can see corresponding dialog box.
5.12.5.3 Watermark
Watermark interface is shown as In Figure 5-156. Please select a file and then click Verify button to see
the file has been tampered with or not
Figure 5-156
5.13 Smart Playback
It is to search and playback the IVS file, human face file and plate recognition record.
Note
483




There are two types to realize intelligent analytics function.
Smart network camera supports intelligent functions: Some smart camera supports the intelligent
functions. For NVR, it just displays the intelligent alarm information from the smart network camera
and set or playback the record file.
NVR supports intelligent functions: The connected network camera does not support intelligent video
analytics function. The NVR supports the analytics function.
This function is to playback the intelligent record file of the smart camera.
5.13.1 IVS (Behavior Analytics)
It is to search and playback the IVS record file.
Step 1 Click Smart Play.
Enter the smart play interface. See Figure 5-157.
Figure 5-157
Step 2
Step 3
Select detection type as IVS.
Select a channel.
Enter the following interface. See Figure 5-158.
Note
The IVS function is for one-channel mode only.
484
Figure 5-158
Step 4
Step 5
Step 6
Step 7
Select a channel number and then click OK.
Set detection type as IVS and then set start time and end time.
Click Historic Analytics.
Device displays the corresponding image.
Click the image; you can view the record file.

Select a file and then click

Select a file and then click
, you can save current file to peripheral storage device.
, you can lock current file in case it will be overwritten in the
future

Select a file and then click
, you can mark the time of the detected event.
5.13.2 Plate recognition
It is to search and playback the record file containing the plate number.
Step 1 From main menu->Operation->Smart Play.
Enter the smart play interface. See Figure 5-159.
485
Figure 5-159
Step 2
Set plate number, channel number, start time, end time.
Note
Device supports fuzzy plate number search function.
Device searches all plate numbers by default if you do not input plate number information.
The plate number search and playback function is for one-channel mode only.
Step 3 Click Historic Analytics.
Device displays the corresponding image.
Step 4 Click the image; you can view the record file.

Select a file and then click

Select a file and then click
, you can save current file to peripheral storage device.
, you can lock current file in case it will be overwritten in the
future

Select a file and then click
, you can mark the time of the detected event.
5.13.3 Human Face
System can search the record containing the human face and then playback.
Important
Before you use this function, please make sure current channel has enabled human face detection
function. Please refer to chapter 5.10.3.4 (Setup->Event->Face Detection) for detailed information.
Set the search type as face detect, set channel, start time and end time.
Click Historic analysis button at the right pane or Analysis button at the bottom of the interface, system
begins to search. You can view the event time and image. See Figure 5-160.
Click the image, system begins playback.

Select the file and then click
, you can save current file to peripheral device.
486

Select the file and then click
, you can lock the file in case it will be overwrtitten in the
future.

Select the file and then click
, you can mark the time of the detected event.
Note
The following human face has been modified for privacy reason. The actual snapshot image has high
definition.
Figure 5-160
5.14 Alarm
Click alarm function, you can see an interface is shown as Figure 5-161.
Here you can set device alarm type and alarm sound setup (Please make sure you have enabled audio
function of corresponding alarm events.).
487
Figure 5-161
Please refer to the following sheet for detailed information.
Type
Parameter
Function
Alarm
Type
Video loss
System alarms when video loss occurs.
Motion detection
System alarms when motion detection alarm
occurs.
Tampering
System alarms when camera is viciously masking.
Disk full
System alarms when disk is full.
Disk error
System alarms when disk error occurs.
External alarm
Alarm input device sends out alarm.
IPC
alarm
external
It refers to the on-off signal from the network
camera. It can activate the NVR local activation
operation.
IPC offline alarm
System can generate an alarm when the network
camera and the NVR are disconnected.
Intelligent detect
System alarms when IVS alarm occurs.
Audio detect
System alarms when audio detect is abnormal.
Operation
Prompt
Check the box here, system can automatically pops
up an alarm icon on the Alarm button in the main
interface when there is an alarm.
Alarm
Sound
Play
sound
alarm
Sound path
System sends out alarm sound when an alarm
occurs. You can specify as you wish.
Here you can specify alarm sound file.
5.15 Log out
Click log out button, system goes back to log in interface. See Figure 5-162.
You need to input user name and password to login again.
488
Figure 5-162
5.16 Un-install Web Control
You can use web un-install tool “uninstall web.bat” to un-install web control.
Please note, before you un-installation, please close all web pages, otherwise the un-installation
might result in error
489
6 Glossary









DHCP: DHCP (Dynamic Host Configuration Protocol) is a network protocol. It is one of the TCP/IP
protocol cluster. It is principally used to assign temporary IP addresses to computers on a network.
DDNS: DDNS (Dynamic Domain Name Server) is a service that maps Internet domain names to IP
addresses. This service is useful to anyone who wants to operate a server (web server, mail server,
ftp server and etc) connected to the internet with a dynamic IP or to someone who wants to connect
to an office computer or server from a remote location with software.
eSATA: eSATA(External Serial AT) is an interface that provides fast data transfer for external storage
devices. It is the extension specifications of a SATA interface.
GPS: GPS (Global Positioning System) is a satellite system, protected by the US military, safely
orbiting thousands of kilometers above the earth.
PPPoE: PPPoE (Point to Point Protocol over Ethernet) is a specification for connecting multiple
computer users on an Ethernet local area network to a remote site. Now the popular mode is ADSL
and it adopts PPPoE protocol.
WIFI: Wi-Fi is the name of a popular wireless networking technology that uses radio waves to
provide wireless high-speed Internet and network connections. The standard is for wireless local
area networks (WLANs). It is like a common language that all the devices use to communicate to
each other. It is actually IEEE802.11, a family of standard The IEEE (Institute of Electrical and
Electronics Engineers Inc.)
3G: 3G is the wireless network standard. It is called 3G because it is the third generation of cellular
telecom standards. 3G is a faster network for phone and data transmission and speed Is over several
hundred kbps. Now there are four standards: CDMA2000, WCDMA, TD-SCDMA and WiMAX.
Dual-stream: The dual-stream technology adopts high-rate bit stream for local HD storage such as
QCIF/CIF/2CIF/DCIF/4CIF encode and one low-rate bit stream for network transmission such as
QCIF/CIF encode. It can balance the local storage and remote network transmission. The
dual-stream can meet the difference band width requirements of the local transmission and the
remote transmission. In this way, the local transmission using high-bit stream can achieve HD
storage and the network transmission adopting low bit stream suitable for the fluency requirements of
the 3G network such as WCDMA, EVDO, TD-SCDMA..
On-off value: It is the non-consecutive signal sampling and output. It includes remote sampling and
remote output. It has two statuses: 1/0.
490
7 FAQ
Questions
Solutions
NVR can not boot up

Input power is not correct.
properly.

Power connection is not correct.

Power switch button is damaged.

Program upgrade is wrong.

HDD malfunction or something wrong with HDD ribbon.

Seagate DB35.1, DB35.2,SV35 or Maxtor 17-g has compatibility
problem. Please upgrade to the latest version to solve this
problem.

Front panel error.

Main board is damaged.

Input voltage is not stable or it is too low.
NVR often automatically

HDD malfunction or something wrong with the ribbon.
shuts down or stops

Button power is not enough.
running.

Front video signal is not stable.

Working environment is too harsh, too much dust.

Hardware malfunction.

HDD is broken.

HDD ribbon is damaged.

HDD cable connection is loose.

Main board SATA port is broken.
There is no video output

Program is not compatible. Please upgrade to the latest version.
whether it is one-channel,

Brightness is 0. Please restore factory default setup.
multiple-channel or


Check your screen saver.
NVR hardware malfunctions.

HDD ribbon is damaged.
I can not search local

HDD is broken.
records.

Upgraded program is not compatible.

The recorded file has been overwritten.

Record function has been disabled.

Video quality setup is too low.

Program read error, bit data is too small. There is mosaic in the full
System can not detect
hard disk.
all-channel output.
Video is distorted when
searching local records.
Time display
correct.
is
not
screen. Please restart the NVR to solve this problem.

HDD data ribbon error.

HDD malfunction.

NVR hardware malfunctions.

Setup is not correct

Battery contact is not correct or voltage is too low.

Crystal is broken.
491
Questions
Solutions
NVR can not control PTZ.

Front panel PTZ error

PTZ decoder setup, connection or installation is not correct.

Cable connection is not correct.

PTZ setup is not correct.

PTZ decoder and NVR protocol is not compatible.

PTZ decoder and NVR address is not compatible.

When there are several decoders, please add 120 Ohm between
the PTZ decoder A/B cables furthest end to delete the
reverberation or impedance matching. Otherwise the PTZ control
is not stable.

The distance is too far.

For Windows 98 or Windows ME user, please update your system
to Windows 2000 sp4. Or you can install client-end software of
lower version. Please note right now, our NVR is not compatible
I can not log in client-end
or web.
There is only mosaic no
video when preview or
playback video file
remotely.
Network connection
not stable.
is
with Windows VISTA control.

ActiveX control has been disabled.

No dx8.1 or higher. Please upgrade display card driver.

Network connection error.

Network setup error.

Password or user name is invalid.

Client-end is not compatible with NVR program.

Network fluency is not good.

Client-end resources are limit.

Current user has no right to monitor.

Network is not stable.

IP address conflict.

MAC address conflict.

PC or device network card is not good.

Burner and NVR are in the same data cable.

System uses too much CPU resources. Please stop record first
Burn error /USB back
error.
and then begin backup.

Data amount exceeds backup device capacity. It may result in
burner error.
Keyboard can not control
NVR.

Backup device is not compatible.

Backup device is damaged.

NVR serial port setup is not correct

Address is not correct

When there are several switchers, power supply is not enough.

Transmission distance is too far.
492
Questions
Solutions

Alarm setup is not correct.
Alarm signal can not been

Alarm output has been open manually.
disarmed.

Input device error or connection is not correct.

Some program versions may have this problem. Please upgrade
your system.
Alarm function is null.

Alarm setup is not correct.

Alarm cable connection is not correct.

Alarm input signal is not correct.

There are two loops connect to one alarm device.

Camera quality is too low. Lens is dirty. Camera is installed against
Record storage period is
not enough.
Can not playback the
the light. Camera aperture setup is not correct.

HDD capacity is not enough.

HDD is damaged.

There is no media player.

No DXB8.1 or higher graphic acceleration software.

There is no DivX503Bundle.exe control when you play the file
downloaded file.
transformed to AVI via media player.

No DivX503Bundle.exe or ffdshow-2004 1012 .exe in Windows XP
OS.
Forgot local menu
operation password or

help. We can guide you to solve this problem.
network password
There is no video. The
screen is in black.
The displayed video is not
full in the monitor.
There is no HDMI output.
The video is not fluent
when
I
view
in
multiple-channel
mode
from the client-end.
Please contact your local service engineer or our sales person for




IPC IP address is not right.
IPC port number is not right.
IPC account (user name/password) is not right.
IPC is offline.
Please cheek current resolution setup. If the current setup is
1920*1080, then you need to set the monitor resolution as 1920*1080.

Displayer is not in HDMI mode.

HDMI cable connection is not right.

The network bandwidth is not sufficient. The multiple-channel
monitor operation needs at least 100M or higher.

Your PC resources are not sufficient. For 16-ch remote monitor
operation, the PC shall have the following environment:
Quad
Core, 2G or higher memory, independent displayer,
display card memory 256M or higher.
493
Questions
I can not connect to the
IPC
Solutions

Please make sure the IPC has booted up.

IPC network connection is right and it is online

IPC IP is in the blacklist.

The device has connected to the too many IPC. It can not transmit
the video.

Check the IPC port value and the time zone is the same as the
NVR.

After I set the NVR
resolution as 1080P, my
monitor can not display.
Make sure current network environment is stable.
Shut down the device and then reboot. When you reboot, please press
the Fn button at the same time and then release after 5 seconds. You
can restore NVR resolution to the default setup.
Use telnet and then input the following command:
My admin account has
been changed and I can
not log in.
cd /mnt/mtd/Config/
rm -rf group
rm -rf password
Reboot the device to restore the default password.
After I login the Web , I
can not find the remote
interface to add the IPC.
Please clear the Web controls and load again.
There is IP and gateway, I
can access the internet
via the router. But I can
not access the internet
after I reboot the NVR.
Please use command PING to check you can connect to the gateway
or not. Use telnet to access and then use command “ifconfig –a” to
check device IP address. If you see the subnet mask and the gateway
has changed after the reboot. Please upgrade the applications and set
again.
I use the VGA montior.I
want to know if I use the
multple-window mode, I
see the video from the
main stream or the sub
stream?

For 32-channel series product, the 9/16-window is using the sub
stream.

For 4/8/16 series product, system is using the main stream no
matter you are in what display mode.
Daily Maintenance

Please use the brush to clean the board, socket connector and the chassis regularly.

The device shall be soundly earthed in case there is audio/video disturbance. Keep the device away
from the static voltage or induced voltage.

Please unplug the power cable before you remove the audio/video signal cable, RS232 or RS485
cable.

Do not connect the TV to the local video output port (VOUT).It may result in video output circuit.

Always shut down the device properly. Please use the shutdown function in the menu, or you can
press the power button in the rear pane for at least three seconds to shut down the device.
494
Otherwise it may result in HDD malfunction.

Please make sure the device is away from the direct sunlight or other heating sources. Please keep
the sound ventilation.

Please check and maintain the device regularly.
495
8
Appendix A HDD Capacity Calculation
Calculate total capacity needed by each device according to video recording (video recording type and
video file storage time).
Step 1: According to Formula (1) to calculate storage capacity q i that is the capacity of each channel
needed for each hour, unit Mbyte.
qi  d i  8  3600  1024
(1)
In the formula: d i means the bit rate, unit Kbit/s
Step 2: After video time requirement is confirmed, according to Formula (2) to calculate the storage
capacity mi , which is storage of each channel needed unit Mbyte.
mi = qi ×hi × Di
(2)
In the formula:
hi means the recording time for each day (hour)
Di means number of days for which the video shall be kept
Step 3: According to Formula (3) to calculate total capacity (accumulation) qT that is needed for all
channels in the device during scheduled video recording.
c
qT   mi
(3)
i 1
In the formula: c means total number of channels in one device
Step 4: According to Formula (4) to calculate total capacity (accumulation) qT that is needed for all
channels in device during alarm video recording (including motion detection).
c
qT   mi ×a%
(4)
i 1
In the formula:a% means alarm occurrence rate
496
9
Appendix B Compatible Network Camera List
Please note all the models in the following list for reference only. For those products not included in the
list, please contact your local retailer or technical supporting engineer for detailed information.
Manufact
ure
Model
Version
Video Encode
Audio/Vid
eo
Protocol
AXIS
P1346
5.40.9.2
H264
√
ONVIF/Private
P3344/P3344E
5.40.9.2
H264
√
ONVIF/Private
P5512
-
H264
√
ONVIF/Private
Q1604
5.40.3.2
H264
√
ONVIF/Private
Q1604-E
5.40.9
H264
√
ONVIF/Private
Q6034E
-
H264
√
ONVIF/Private
Q6035
5.40.9
H264
√
ONVIF/Private
Q1755
-
H264
√
ONVIF/Private
M7001
-
H264
√
Private
M3204
5.40.9.2
H264
√
Private
P3367
HEAD LFP4_0
130220
H264
√
ONVIF
P5532-P
HEAD LFP4_0
130220
H264
√
ONVIF
ACM-3511
A1D-220-V3.12
.15-AC
MPEG4
√
Private
ACM-8221
A1D-220-V3.13
.16-AC
MPEG4
√
Private
AV1115
65246
H264
√
Private
AV10005DN
65197
H264
√
Private
AV2115DN
65246
H264
√
Private
AV2515DN
65199
H264
√
Private
AV2815
65197
H264
√
Private
AV5115DN
65246
H264
√
Private
AV8185DN
65197
H264
√
Private
NBN-921-P
-
H264
√
ONVIF
NBC-455-12P
-
H264
√
ONVIF
VG5-825
9500453
H264
√
ONVIF
NBN-832
66500500
H264
√
ONVIF
VEZ-211-IWT
EIVA
-
H264
√
ONVIF
NBC-255-P
15500152
H264
√
ONVIF
VIP-X1XF
-
H264
√
ONVIF
B0100
-
H264
√
ONVIF
D100
-
H264
√
ONVIF
GE-100-CB
-
H264
√
ONVIF
FB-100A
v1.0.3.9
H264
√
ONVIF
FD-100A
v1.0.3.3
H264
√
ONVIF
ACTi
Arecont
Bosch
Brikcom
497
Manufact
ure
Model
Version
Video Encode
Audio/Vid
eo
Protocol
Cannon
VB-M400
-
H264
√
Private
CNB
MPix2.0DIR
XNETM112011
1229
H264
√
ONVIF
VIPBL1.3MIR
VF
XNETM210011
1229
H264
√
ONVIF
IGC-2050F
XNETM210011
1229
H264
√
ONVIF
CP-NC9-K
6.E.2.7776
H264
√
ONVIF/Private
CP-NC9W-K
6.E.2.7776
H264
√
Private
CP-ND10-R
cp20111129AN
S
H264
√
ONVIF
CP-ND20-R
cp20111129AN
S
H264
√
ONVIF
CP-NS12W-C
R
cp20110808NS
H264
√
ONVIF
VS201
cp20111129NS
H264
√
ONVIF
CP-NB20-R
cp20110808BN
S
H264
√
ONVIF
CP-NT20VL3R
cp20110808BN
S
H264
√
ONVIF
CP-NS36W-A
R
cp20110808NS
H264
√
ONVIF
CP-ND20VL2R
cp20110808BN
S
H264
√
ONVIF
CP-RNP-1820
cp20120821NS
A
H264
√
Private
CP-RNC-TP2
0FL3C
cp20120821NS
A
H264
√
Private
CP-RNP-12D
cp20120828AN
S
H264
√
Private
CP-RNC-DV1
0
cp20120821NS
A
H264
√
Private
CP-RNC-DP2
0FL2C
cp20120821NS
A
H264
√
Private
ICS-13
d20120214NS
H264
√
ONVIF/Private
ICS-20W
vt20111123NSA
H264
√
ONVIF/Private
NA222
-
H264
√
ONVIF
MPC-IPVD-03
13
k20111208ANS
H264
√
ONVIF/Private
MPC-IPVD-03
13AF
k20111208BNS
H264
√
ONVIF/Private
HIDC-1100PT
h.2.2.1824
H264
√
ONVIF
HIDC-1100P
h.2.2.1824
H264
√
ONVIF
CP PLUS
Dynacolor
Honeywell
498
Manufact
ure
LG
Imatek
Panasonic
PELCO
Model
Version
Video Encode
Audio/Vid
eo
Protocol
HIDC-0100P
h.2.2.1824
H264
√
ONVIF
HIDC-1300V
2.0.0.21
H264
√
ONVIF
HICC-1300W
2.0.1.7
H264
√
ONVIF
HICC-2300
2.0.0.21
H264
√
ONVIF
HDZ20HDX
H20130114NS
A
H264
√
ONVIF
LW342-FP
-
H264
√
Private
LNB5100
-
H264
√
ONVIF
KNC-B5000
-
H264
√
Private
KNC-B5162
-
H264
√
Private
KNC-B2161
-
H264
√
Private
NP240/CH
-
MPEG4
√
Private
WV-NP502
-
MPEG4
√
Private
WV-SP102H
1.41
H264
√
ONVIF/Private
WV-SP105H
-
H264
√
ONVIF/Private
WV-SP302H
1.41
H264、MPEG4
√
ONVIF/Private
WV-SP306H
1.4
H264、MPEG4
√
ONVIF/Private
WV-SP508H
-
H264、MPEG4
√
ONVIF/Private
WV-SP509H
-
H264、MPEG4
√
ONVIF/Private
WV-SF332H
1.41
H264、MPEG4
√
ONVIF/Private
WV-SW316H
1.41
H264、MPEG4
√
ONVIF/Private
WV-SW355H
1.41
H264、MPEG4
√
ONVIF/Private
WV-SW352H
-
H264、MPEG4
√
ONVIF/Private
WV-SW152E
1.03
H264、MPEG4
√
ONVIF/Private
WV-SW558H
-
H264、MPEG4
√
ONVIF/Private
WV-SW559H
-
H264、MPEG4
√
ONVIF/Private
WV-SP105H
1.03
H264、MPEG4
√
ONVIF/Private
WV-SW155E
1.03
H264、MPEG4
√
ONVIF/Private
WV-SF336H
1.44
H264、MPEG4
√
ONVIF/Private
WV-SF332H
1.41
H264、MPEG4
√
ONVIF/Private
WV-SF132E
1.03
H264、MPEG4
√
ONVIF/Private
WV-SF135E
1.03
H264、MPEG4
√
ONVIF/Private
WV-SF346H
1.41
H264、MPEG4
√
ONVIF/Private
WV-SF342H
1.41
H264、MPEG4
√
ONVIF/Private
WV-SC385H
1.08
H264、MPEG4
√
ONVIF/Private
WV-SC386H
1.08
H264、MPEG4
√
ONVIF/Private
WV-SP539
1.66
H264、MPEG4
√
ONVIF
DG-SC385
1.66
H264、MPEG4
√
ONVIF
IXSOLW
1.8.1-20110912
-1.9082-A1.661
7
H264
√
Private
IDE20DN
1.7.41.9111-O3
.6725
H264
√
Private
499
Manufact
ure
Samsung
Sony
SANYO
Model
Version
Video Encode
Audio/Vid
eo
Protocol
D5118
1.7.8.9310-A1.
5288
H264
√
Private
IM10C10
1.6.13.9261-O2
.4657
H264
√
Private
DD4N-X
01.02.0015
MPEG4
√
Private
DD423-X
01.02.0006
MPEG4
√
Private
D5220
1.8.3-FC2-2012
0614-1.9320-A
1.8035
H264
√
Private
SNB-3000P
2.41
H264、MPEG4
√
ONVIF/Private
SNP-3120
1.22_110120_1
H264、MPEG4
√
ONVIF/Private
SNP-3370
1.21_110318
MPEG4
√
Private
SNB-5000
2.10_111227
H264、MPEG4
√
ONVIF/Private
SND-5080
-
H264、MPEG4
√
Private
SNZ-5200
1.02_110512
H264、MPEG4
√
ONVIF/Private
SNP-5200
1.04_110825
H264、MPEG4
√
ONVIF/Private
SNB-7000
1.10_110819
H264
√
ONVIF/Private
SNB-6004
V1.0.0
H264
√
ONVIF
SNC-DH110
1.50.00
H264
√
ONVIF/Private
SNC-CH120
1.50.00
H264
√
ONVIF/Private
SNC-CH135
1.73.01
H264
√
ONVIF/Private
SNC-CH140
1.50.00
H264
√
ONVIF/Private
SNC-CH210
1.73.00
H264
√
ONVIF/Private
SNC-DH210
1.73.00
H264
√
ONVIF/Private
SNC-DH240
1.50.00
H264
√
ONVIF/Private
SNC-DH240-T
1.73.01
H264
√
ONVIF/Private
SNC-CH260
1.74.01
H264
√
ONVIF/Private
SNC-CH280
1.73.01
H264
√
ONVIF/Private
SNC-RH-124
1.73.00
H264
√
ONVIF/Private
SNC-RS46P
1.73.00
H264
√
ONVIF/Private
SNC-ER550
1.74.01
H264
√
ONVIF/Private
SNC-ER580
1.74.01
H264
√
ONVIF/Private
SNC-ER580
1.78.00
H264
√
ONVIF
SNC-VM631
1.4.0
H264
√
ONVIF
WV-SP306
1.61.00
H264、MPEG4
√
SDK
WV-SP306
1.61.00
H264
√
ONVIF
SNC-VB600
1.5.0
H264
√
Private
SNC-VM600
1.5.0
H264
√
Private
SNC-VB630
1.5.0
H264
√
Private
SNC-VM630
1.5.0
H264
√
Private
VCC-HDN400
0PC
-
H264
√
ONVIF
500
Note

This manual is for reference only. Slight difference may be found in the user interface.

All the designs and software here are subject to change without prior written notice.

All trademarks and registered trademarks are the properties of their respective owners.

If there is any uncertainty or controversy, please refer to the final explanation of us.

Please visit our website or contact your local service engineer for more information.
501
Download PDF
Similar pages