Introduction
Owner’s Manual
INSTRUCCIONES EN ESPAÑOL INCLUIDAS
Basic Setup
ZC320SL8
Connections
Digital Video Disc Recorder
Disc
Management
Recording
Playback
Editing
Function Setup
THIS UNIT HAS NO TUNER SYSTEM, YOU MUST CONNECT TO EXTERNAL TUNER.
Others
© 2007 Funai Electric Co., Ltd.
Español
IF YOU NEED ADDITIONAL ASSISTANCE WITH SETUP OR OPERATING AFTER
READING OWNER’S MANUAL, PLEASE CALL TOLL FREE 1-800-968-3429, OR
VISIT OUR WEB SITE AT http://www.SylvaniaConsumerElectronics.com
PRECAUTIONS
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
The caution marking is located on the rear of the cabinet.
Laser Safety
This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device,
due to possible eye injury.
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. DO NOT STARE INTO BEAM.
LOCATION: INSIDE, NEAR THE DECK MECHANISM.
FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the modifications are expressly approved in the manual. The
user could lose the authority to operate this equipment if an unauthorized change or modification is made.
RADIO-TV INTERFERENCE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and receiver.
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance
with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations
concerning chemical wastes.
Make your contribution to the environment!!!
• Used up batteries do not belong in the dust bin.
• You can dispose of them at a collection point for used up batteries or special waste.
Contact your council for details.
For Customer Use:
Read carefully the information located at the back of this unit and enter below the Model No. and Serial No. Retain
this information for future reference.
Model No. _____________________
Serial No. _____________________
2
EN
Important Safeguards
Basic Setup
Disc
Management
Recording
Playback
Editing
Function Setup
Others
12. Power Cord Protection - Power supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the
appliance.
13. Lightning - For added protection for this product during
a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall
outlet. This will prevent damage to the product due to
lightning and power-line surges.
14. Power Lines - An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into
such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep
from touching such power lines or circuits as contact
with them might be fatal.
15. Overloading - Do not overload wall outlets and extension
cords as this can result in a risk of fire or electric shock.
16. Object and Liquid Entry - Never push objects of any kind
into this product through any openings as they may
touch dangerous voltage points or short-out parts that
could result in a fire or electric shock. Never spill liquid of
any kind on the product.
17. Servicing - Do not attempt to service this product yourself
as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
18. Damage Requiring Service - Unplug this product from
the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the
product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to its normal
operation.
e. If the product has been dropped or damaged in any way.
f. When the product exhibits a distinct change in
performance this indicates a need for service.
19. Replacement Parts - When replacement parts are
required, be sure the service technician has used
replacement parts specified by the manufacturer or
have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric
shock or other hazards.
20. Safety Check - Upon completion of any service or repairs
to this product, ask the service technician to perform
safety checks to determine that the product is in proper
operating condition.
21. Heat - This product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
Connections
Español
1. Read Instructions - All the safety and operating
instructions should be read before the appliance is
operated.
2. Retain Instructions- The safety and operating instructions
should be retained for future reference.
3. Heed Warnings - All warnings on the appliance and in
the operating instructions should be adhered to.
4. Follow Instructions - All operating and use instructions
should be followed.
5. Cleaning - Unplug this product from the wall outlet
before cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
EXCEPTION: A product that is meant for uninterrupted
service and, that for some specific reason, such as the
possibility of the loss of an authorization code for a
CATV converter, is not intended to be unplugged by the
user for cleaning or any other purpose, may exclude the
reference to unplugging the appliance in the cleaning
description otherwise required in item 5.
6. Attachments - Do not use attachments not
recommended by the product manufacturer as they may
cause hazards.
7. Water and Moisture- Do not use this product near water,
for example, near a bath tub, wash bowl, kitchen sink,
or laundry tub, in a wet basement, or near a swimming
pool, and the like.
8. Accessories - Do not place this product on an unstable
cart, stand, tripod, bracket, or table. The product may
fall, causing serious injury to a child or adult, and
serious damage to the appliance. Use only with a cart,
stand, tripod, bracket, or table recommended by the
manufacturer, or sold with the product. Any mounting
of the appliance should follow the manufacturer's
instructions and should use a
mounting accessory recommended
by the manufacturer. An appliance
and cart combination should be
moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the appliance and cart
combination to overturn.
9. Ventilation - Slots and openings in the cabinet are
provided for ventilation and to ensure reliable operation
of the product and to protect it from overheating,
and these openings must not be blocked or covered.
The openings should never be blocked by placing the
product on a bed, sofa, rug, or other similar surface. This
product should not be placed in a built-in installation
such as a bookcase or rack unless proper ventilation is
provided or the manufacturer's instructions have been
adhered to.
10. Power Sources - This product should be operated only
from the type of power source indicated on the marking
label. If you are not sure of the type of power supply
to your home, consult your appliance dealer or local
power company. For products intended to operate from
battery power, or other sources, refer to the operating
instructions.
11. Grounding or Polarization - This product is equipped
with a polarized alternating-current line plug (a plug
having one blade wider than the other). This plug will
fit into the power outlet only one way. This is a safety
feature. If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should still fail
to fit, contact your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of the polarized
plug.
Introduction
PRECAUTIONS
EN
3
PRECAUTIONS
Installation Location
For safety and optimum performance of this unit:
• Install the unit in a horizontal and stable position. Do
not place anything directly on top of the unit. Do not
place the unit directly on top of the TV.
• Shield it from direct sunlight and keep it away from
devices of intense heat. Avoid dusty or humid places.
Avoid places with insufficient ventilation for proper
heat dissipation. Do not block the ventilation holes on
the sides of the unit. Avoid locations subject to strong
vibration or strong magnetic fields.
Supplied Accessories
remote control (NB089UD) with batteries (AAx2)
RCA audio/video cables (WPZ0102TM018/WPZ0102LTE01)
Avoid the Hazards of Electrical Shock and Fire
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting it
from AC outlet. Grasp it by the plug.
• If, by accident, water is spilled on this unit, unplug
the power cord immediately and take the unit to our
Authorized Service Center for servicing.
owner's manual (1VMN23368)
Moisture Condensation Warning
Moisture condensation may occur inside the unit
when it is moved from a cold place to a warm place or
after heating a cold room or under conditions of high
humidity. Do not use this unit at least for 2 hours until its
inside gets dry.
About Copyright
Unauthorized copying, broadcasting, public performance
and lending of discs are prohibited.
This product incorporates copyright protection
technology that is protected by U.S. patents and other
intellectual property rights. Use of this copyright
protection technology must be authorized by
Macrovision, and is intended for home and other
limited viewing uses only unless otherwise authorized
by Macrovision. Reverse engineering or disassembly is
prohibited.
Notice for Progressive Scan Output
Consumers should note that not all high definition
television sets are fully compatible with this product and
may cause artifacts to be displayed in the picture. In case
of picture problems with 525 progressive scan output,
it is recommended that the user switch the connection
to the ‘standard definition’ output. If there are questions
regarding your TV set compatibility with this 525p DVD
player, please contact our customer service center.
4
EN
quick guide (1VMN23370)
Introduction
PRECAUTIONS
Maintenance
IR signal check
• Please refer to relevant topics on “TROUBLESHOOTING”
on pages 80-84 before returning the product.
• If this unit becomes inoperative, do not try to correct
the problem by yourself. There are no user-serviceable
parts inside. Turn off, unplug the power plug and
please call our help line mentioned on the front page
to locate an Authorized Service Center.
If the remote control does not work properly, you can test
if the remote control sends out the infrared signal with
AM radio or a digital camera (including built-in camera
of cellular phone). It will help to define the cause of
malfunction.
Cleaning the cabinet
Basic Setup
• Use a soft cloth slightly moistened with a mild
detergent solution. Do not use a solution containing
alcohol, spirits, ammonia or abrasive.
• With an AM radio:
Tune an AM radio to a station with no
broadcasting. Press a button on remote
control toward the radio. Sound will be
fluttering when you press any key and the
radio receives the signal. This means the
remote control is working.
Cleaning discs
Cleaning the disc lens
Disc handling
Manufactured under license from
Dolby Laboratories. “Dolby” and the
double-D symbol are trademarks of
Dolby Laboratories.
Function Setup
© 2007 Funai Electric Co., Ltd.
Others
All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed,
downloaded or stored in any storage medium, in any form or for any purpose without the express prior written
consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto is
strictly prohibited.
Information in this document is subject to change without notice. Funai reserves the right to change the content
herein without the obligation to notify any person or organization of such changes.
5
Español
with the
design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way without
the express written consent of Funai. All other trademarks used herein remain the exclusive property of their respective
owners. Nothing contained in this manual should be construed as granting, by implication or otherwise, any license or
right to use any of the trademarks displayed herein. Misuse of any trademarks or any other content in this manual is
strictly prohibited. Funai shall aggressively enforce its intellectual property rights to the fullest extent of the law.
EN
Editing
Dolby Digital Recording
“Dolby® Digital Recording enables consumers to record
high-quality video with stereo sound on recordable
DVD discs. The technology, when utilized instead of
PCM recording, also saves recordable disc space, allowing for higher video resolution or extended recording
time on each DVD. DVDs created using Dolby Digital
Recording will play back on all DVD-video players.”
Note: This is true when the players are compatible with
actual recordable DVD discs.
Playback
• Handle the discs so that fingerprints and dust do not
adhere to the surfaces of the discs.
• Always store the disc in its protective case when it is
not used.
“Kodak Picture CD COMPATIBLE” is a trademark of
Eastman Kodak Company.
Recording
• If this unit still does not perform properly
although you refer to the relevant sections and to
“TROUBLESHOOTING” in this owner's manual, the laser
optical pickup unit may be dirty. Consult your dealer
or an Authorized Service Center for inspection and
cleaning of the laser optical pickup unit.
• With a digital camera (including built-in
camera of cellular phone):
Direct a digital camera to remote control,
press and hold a button on remote control.
If infrared light appears through digital
camera, the remote control is working.
Disc
Management
• When a disc becomes dirty, clean it with a cleaning
cloth. Wipe the disc from the center to out. Do not
wipe in a circular motion.
• Do not use solvents such as benzine, thinner,
commercially available cleaners, detergent, abrasive
cleaning agents or antistatic spray intended for analog
records.
Connections
Servicing
CONTENTS
Introduction
PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Symbols Used in this Owner’s Manual . . . . . . . . . . . . . . . . 7
FUNCTIONAL OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . 10
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Front Panel Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Connections
CONNECTION TO AN EXTERNAL TUNER. . . . . . . . . . .
SETTINGS FOR THE VIDEO INPUT. . . . . . . . . . . . . . . . .
CONNECTION TO A TV. . . . . . . . . . . . . . . . . . . . . . . . . . .
CONNECTION TO AN AUDIO SYSTEM . . . . . . . . . . . . .
15
16
17
18
Basic Setup
GUIDE TO ON-SCREEN DISPLAYS AND MENUS . . . . 19
On-Screen Display / Menu. . . . . . . . . . . . . . . . . . . . . . . . . . .19
Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
INITIAL SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
SETTING THE CLOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Clock Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Disc Management
FORMATTING A DISC . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Choosing the Recording Format
of a Brand-New DVD-RW . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Reformatting a Disc Manually . . . . . . . . . . . . . . . . . . . . . . .24
PREPARING A DISC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Setting for Auto Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Setting Aspect Ratio for Video Mode Recording . . . . . .25
SETTING A DISC TO PROTECT . . . . . . . . . . . . . . . . . . . . 26
PLAYING THE DISCS IN OTHER DVD PLAYERS . . . . . 27
Auto Finalizing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Finalizing a Disc. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Recording
INFORMATION ON DVD RECORDING . . . . . . . . . . . . . 30
Recording Speed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Restrictions on Recording . . . . . . . . . . . . . . . . . . . . . . . . . . .30
BASIC RECORDING &
ONE-TOUCH TIMER RECORDING . . . . . . . . . . . . . . . . . 31
TIMER RECORDING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Hints for Timer Recording . . . . . . . . . . . . . . . . . . . . . . . . . . .36
SATELLITE LINK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
SETTINGS FOR AN EXTERNAL DEVICE . . . . . . . . . . . . 39
Connection to an External Device . . . . . . . . . . . . . . . . . . .39
Recording from an External Device . . . . . . . . . . . . . . . . . .40
Playback
INFORMATION ON PLAYBACK . . . . . . . . . . . . . . . . . . . 41
Structure of Disc Contents. . . . . . . . . . . . . . . . . . . . . . . . . . .41
BASIC PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Direct Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Playback from the Title List . . . . . . . . . . . . . . . . . . . . . . . . . .43
Playing Back an Audio CD and
a CD-RW/-R with MP3 / JPEG Files . . . . . . . . . . . . . . . . . . .44
Using the Title / Disc Menu . . . . . . . . . . . . . . . . . . . . . . . . . .45
Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
SPECIAL PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Resume Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Fast Forward / Fast Reverse Playback . . . . . . . . . . . . . . . .46
Skipping TV Commercials During Playback. . . . . . . . . . .46
Rapid Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Step by Step Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Slow Forward / Slow Reverse Playback. . . . . . . . . . . . . . .47
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Marker Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Title/Chapter Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Track Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Time Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
REPEAT/RANDOM/PROGRAM PLAYBACK/
SLIDE SHOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Repeat Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Random Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Program Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Slide Show. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
SELECTING THE FORMAT OF AUDIO AND VIDEO . . 53
Switching Subtitles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Switching Audio Soundtrack . . . . . . . . . . . . . . . . . . . . . . . .53
Switching Virtual Surround System . . . . . . . . . . . . . . . . . .54
Switching Camera Angles . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Reducing Block Noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Editing
INFORMATION ON DISC EDITING. . . . . . . . . . . . . . . . . 55
Guide to a Title List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Editing Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
DELETING TITLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
CREATING/DELETING PLAYLIST . . . . . . . . . . . . . . . . . . 58
Adding Titles to a Playlist. . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Erasing All Playlist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
EDITING DISCS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Putting Names on Titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Setting or Clearing Chapter Marks . . . . . . . . . . . . . . . . . . .62
Deleting a Part of a Title . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Dividing a Title. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Combining Titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Setting or Releasing the Title Protection . . . . . . . . . . . . .67
Setting or Clearing All Chapter Marks at Once. . . . . . . .68
Function Setup
LIST OF SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
SETUPS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Reset All . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Others
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Frequently Asked Questions. . . . . . . . . . . . . . . . . . . . . . . . .84
LANGUAGE CODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
GLOSSARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Español
ESPAÑOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . Back cover
6
EN
Introduction
FEATURES
This unit not only plays back DVD and CD but also offers features for you to record on DVD and edit them after that.
The following features are offered with this unit.
Recording
Deleting titles:
You can delete titles which you do not need anymore.
Setting or clearing chapter marks:
You can set or clear chapter marks on titles.
Deleting parts of titles:
You can delete a specific part of a title.
Dividing or combining titles:
You can divide or combine a title.
Editing title names:
You can change the title name you prefer.
Connections
Basic Setup
Compatibility
Available for playing back discs on a regular DVD
player:
Recorded discs can be played back on regular DVD
players, including computer DVD drives compatible with
DVD-video playback.
Others
Playback
Symbols Used in this Owner’s Manual
Playback
To specify for what disc type each function is, we put
the following symbols at the beginning of each item to
operate.
* DVD-R recorded in VR format or non compatible
recording format are not playable.
Editing
Symbol Description
For Recording, Playing Back, and Editing
Description refers to DVD-RW in video mode
Function Setup
Theater surround sound in your home:
When connecting the unit to an amplifier or a decoder
which is compatible with Dolby Digital, you can experience the theater surround sound from discs with surround sound system.
Quick search for what you want to watch:
You can easily find the part you want to watch using the
search function. Search for a desired point on a disc by
title, chapter/track or time.
Virtual surround system:
You can enjoy stereophonic space through your existing
2 channel stereo system.
Playing back MP3/JPEG/Kodak Picture CD files:
You can enjoy MP3/JPEG/Kodak Picture CD files which are
recorded on CD-RW/-R.
Recording
Progressive scan system
Unlike conventional interlace scanning, the progressive
scan system provides less flickering and images in higher
resolution than that of traditional television signals.
Line through output
When an external device, such as cable/satellite box, is
connected to L1 (Rear) jacks of this unit, the signal from the
external device can be output even when the power of the
unit is off.
Disc
Management
This unit is compatible with recording on DVD-RW which is
recordable repeatedly and DVD-R which accept the additional recordings until the disc becomes full but not overwritable. You can choose either one for your convenience.
Up to 12 program recording:
You can program the unit to record up to 12 programs
within a one-month period. Daily or weekly program
recordings are also available.
One-touch timer recording (OTR):
You can easily set a recording time as you prefer. Every
time [REC/OTR] is pressed during recording, the recording time will be increased by 30 minutes up to 8 hours.
The recording automatically stops when the recording
time you set is reached.
Automatic chapter mark setting:
Chapter marks will be put on recordings as you set
before attempting to record.
Automatic title menu making:
The unit creates title menu automatically when finalizing
discs.
Automatic playlist making (VR mode DVD-RW):
The unit creates a playlist automatically after recording.
Automatic title finalizing (Video mode DVD-RW/-R):
You can finalize discs automatically after finishing all
timer recordings or at the end of the disc space if you set
this in the main menu.
Left channel stereo recording:
This unit can record the sound of the left channel monaural input as left and right channels automatically (the
input from the L2 jacks only).
Editing
Description refers to DVD-RW in VR mode
Description refers to DVD-R in video mode
For Playback only
Description refers to DVD-video
Others
Description refers to audio CD
Description refers to CD-RW/-R with MP3 files
Description refers to CD-RW/-R with JPEG files,
including Kodak Picture CD files
EN
7
Español
If you do not find any of the symbols listed above under the
function heading, the operation is applicable to all media.
FEATURES
Discs for Recording, Playing back
Disc type
DVD-RW
DVD-R
Logo
Automatically
formatted in video mode
Format Can be formatted in VR or video mode
Video Mode
VR Mode
Icon
Maximum record 480 min (12cm)
time 144 min (8cm)
480 min (12cm)
144 min (8cm)
480 min (12cm)
144 min (8cm)
Ver.2.0
Ver.2.0/4×
Ver.2.0/8×
Ver2.0/16×
Ver.1.1,1.2
Recordable/playable
Ver.1.1/2× CPRM compatible
versions
Ver.1.2/4× CPRM compatible
Playable on most
DVD players.
Finalization
Compatibility
necessary.
(DVD menu will be
created)
Playable only on VR
mode compatible
unit.
Finalization
recommended.
Playable on most DVD players.
Finalization necessary.
(DVD menu will be created)
Available Features
Recording Features
Record TV
programs
✔
✔
Reuse by deleting
the current
contents
✔
✔
Record 16:9 size
pictures
✔
✔
Record copy-once
programs
Create chapters
at fixed intervals
(auto chapter)
✔
✔
✔*
✔
Editing Features
Scene delete
✔
Playlist
Original
✔
✔
✔
✔
Create chapters
wherever you like
(chapter mark)
✔
✔
Divide a title
✔
Combine titles
✔
Edit title name
✔
✔
✔
Hide chapters
Delete a title
✔
✔
Create a playlist
✔
Protect a title
✔
✔ : Available
*CPRM compatible disc only.
8
✔
EN
: Not available
✔
Introduction
FEATURES
Discs for playing back
Disc Type
DVD-VIDEO
CD-DA
CD-RW
CD-R
Connections
Logo
Icon
Files for playing back
Type of title
JPEG
CD-RW/-R
CD-RW/-R
Basic Setup
MP3
Icon
Media
is a trademark of DVD Format/Logo Licensing Corporation.
are capable of playing DVD-RW
Unplayable Discs
Region Codes
This unit has been designed to play back DVD
with region 1. DVD must be labeled for ALL
regions or for region 1 in order to play back on
the unit. You cannot play back DVD that are
labeled for other regions. Look for the symbols
on the right on your DVD. If these region
symbols do not appear on your DVD, you
cannot play back the DVD in this unit.
The number inside the globe refers to region of the world.
A DVD labeled for a specific region can only play back on
the unit with the same region code.
Playback
Editing
The following discs will not play back on this unit.
• CD-ROM
• Compact Disc-Interactive (CD-I)
• Video Single Disc (VSD) • DVD-ROM
• DVD-audio
• Unfinalized disc
• DVD contains MP3 or JPEG files
• DVD-R recorded in VR format or non compatible
recording format
On the following disc, the sound may not be heard.
• Super audio CD - Only the sound on the CD layer can be
heard. The sound on the high-density super audio CD
layer cannot be heard.
DVD is recorded in different color systems throughout
the world. The most common color system is NTSC
(which is used primarily in the United States and Canada).
This unit uses NTSC, so DVD you play back must be
recorded in the NTSC system. You cannot play back DVD
recorded in other color systems.
Recording
• Following discs are recommended for good recording
quality and are proven to be compatible with this unit.
However, depending on the media condition the unit
may not read the disc properly.
Verbatim
DVD-R 8x,
DVD-RW 2x
JVC
DVD-RW 4x
Maxell
DVD-R 8x/16x
Performance of any other discs are not guaranteed.
Color Systems
Disc
Management
DVD players with
recorded in VR mode.
Function Setup
Others
Español
EN
9
FUNCTIONAL OVERVIEW
Front Panel
1
3
2*
13
12
4
5 6* 7
11 10
9
8
(*) The unit can also be turned on by pressing these buttons.
1. Disc tray
Place a disc when the disc tray is opened.
2. OPEN/CLOSE A button*
Press to open or close the disc tray.
3. INPUT button
Press to select the appropriate input.
4. PAUSE F button
Press to pause playback or recording.
5. STOP C button
Press to stop playback or recording.
6. PLAY B button*
Press to start or resume playback.
7. REC/OTR I button
Press once to start a recording. Press repeatedly to
start one-touch timer recording.
8. POWER y button
Press to turn the unit on and off.
If timer programmings have been set, press to set the
unit in timer-standby mode.
10
EN
9. AUDIO input jacks (L2)
Use to connect external device with a RCA audio
cable.
10. VIDEO input jack (L2)
Use to connect external device with a RCA video
cable.
11. S-VIDEO input jack (L2)
Use to connect the S-video output of external device
with an S-video cable.
12. Infrared sensor window
Receive signals from your remote control so that you
can control the unit from a distance.
13. Display
Refer to “Front Panel Display” on page 14.
Introduction
FUNCTIONAL OVERVIEW
Rear Panel
1
2 3
4
L
L
Connections
VIDEO VIDEO
IN
OUT
Y
PB/CB
R
AUDIO IN
(L1)
9
IN
R
S-VIDEO AUDIO OUT
8 7
PR/CR
COMPONENT
VIDEO OUT
OUT
COAXIAL
S-VIDEO
DIGITAL AUDIO OUTPUT
PCM / BITSTREAM
6
5
Disc
Management
7. AUDIO OUT jacks
Use to connect a TV monitor, AV receiver or other
device with a RCA audio cable.
8. S-VIDEO IN jack (L1)
Use to connect the S-video output of external device
with an S-video cable.
9. AUDIO IN jacks (L1)
Use to connect external device with a RCA audio
cable.
Basic Setup
Note
• Do not touch the inner pins of the jacks on the rear
panel. Electrostatic discharge may cause permanent
damage to the unit.
Recording
1. VIDEO IN jack (L1)
Use to connect external device with a RCA video
cable.
2. VIDEO OUT jack
Use to connect a TV monitor, AV receiver or other
device with a RCA video cable.
3. COMPONENT VIDEO OUTPUT jacks
Use to connect a TV monitor with component video
inputs with a component video cable.
4. AC Power Cord
Connect to a standard AC outlet to supply power to
this unit.
5. COAXIAL DIGITAL AUDIO OUTPUT jack
Use to connect an AV receiver, Dolby Digital decoder
or other device with a digital audio coaxial input jack
with a digital audio coaxial cable.
6. S-VIDEO OUT jack
Use to connect the S-video input of a TV monitor, AV
receiver or other device with an S-video cable.
Playback
Editing
Function Setup
Others
Español
EN
11
FUNCTIONAL OVERVIEW
Remote Control
Installing the Batteries in the Remote Control
Install the batteries (AAx2) matching the polarity
indicated inside battery compartment of the remote
control.
1
Open the cover.
2
Insert batteries.
Using a Remote Control
Keep in mind the following when using the remote
control:
• Make sure that there are no obstacles between the remote
control and the infrared sensor window on the unit.
• Remote operation may become unreliable if strong
sunlight or fluorescent light is shining on the infrared
sensor window of the unit.
• Remote control for different devices can interfere with
each other. Avoid using remote control for other device
located close to the unit.
• Replace the batteries when you notice a fall off in the
operating range of the remote control.
• The maximum operable ranges from the unit are as
follows.
- Line of sight: approx. 23 feet (7m)
- Either side of the center:
approx. 16 feet (5m) within 30°
- Above: approx. 16 feet (5m) within 15°
- Below: approx. 10 feet (3m) within 30°
Make sure to match + and - on the batteries to
the marks indicated in the battery compartment.
3
16 feet (5m)
30˚
16 feet (5m)
30˚
23 feet (7m)
Close the cover.
2
1
POWER
TIMER
PROG.
.@/:
ABC
DEF
INPUT SELECT
GHI
JKL
MNO
AUDIO
PQRS
TUV
WXYZ
REPEAT
DISPLAY
SPACE
CLEAR
SETUP
3
4
OPEN/CLOSE
ZOOM
14*
15
16
17
Caution:
Never throw batteries into a fire.
6
7
Note:
• Be sure to use AA size batteries.
• Dispose of batteries in a designated disposal area.
• Batteries should always be disposed of with the
environment in mind. Always dispose of batteries in
accordance with applicable laws and regulations.
• If the remote control does not operate correctly, or if
the operating range becomes reduced, replace
batteries with new ones.
• When necessary to replace batteries in the remote
control, always replace both batteries with new ones.
Never mix battery types or use new and used
batteries in combination.
• Always remove batteries from remote control if they
are dead or if the remote control is not to be used for
an extended period of time. This will prevent battery
acid from leaking into the battery compartment.
12
EN
5
TOP MENU MENU/LIST
ENTER
8
9
11
RETURN
19
20
10
12
13
REC SPEED
REV
PLAY
FWD
X1.3/0.8
SKIP
PAUSE
SKIP
REC/OTR
STOP
CM SKIP
23
18
21
22*
24
25
26
27
DVD RECORDER
NB089
(*) The unit can also be turned on by pressing these buttons.
Basic Setup
Disc
Management
Recording
Playback
18. CLEAR button
Press to clear the password once entered, to cancel
the programming for CD, to clear the selecting marker number in the display menu, etc.
19. SETUP button
• Press to display the main menu.
• During DVD playback, press and hold for more than
3 seconds to switch the progressive scanning mode
to the interlace mode.
20. ENTER button
Press to confirm or select menu items.
21. RETURN
button
Press to return to the previously displayed menu
screen.
22. PLAY B button*
Press to start playback or resume playback.
23. FWD D button
• During playback, press to fast forward playback.
• When playback is in pause, press to slow forward
playback.
24. PAUSE F button
Press to pause playback or recording.
25. SKIP G button
• During playback, press to skip to the next chapter,
track or file.
• When playback is in pause, press repeatedly to forward the playback step by step.
26. CM SKIP button
During playback, press to skip 30 seconds.
27. STOP C button
• Press to stop playback or recording.
• Press to exit from the title list.
Connections
Editing
Function Setup
Others
1. TIMER PROG. button
Press to display the timer programming list.
2. ZOOM button
During playback, press to enlarge the picture on the
TV screen.
3. POWER button
Press to turn the unit on and off. If timer programmings have been set, press to set the unit in timerstandby mode.
4. Number/Character buttons
• Press to select a title/chapter/track/file on display.
• Press to enter values for the settings in the main
menu.
• Press to enter title names.
5. DISPLAY button
Press to display the display menu on or off.
6. TOP MENU button
Press to display the title list.
7. MENU/LIST button
Press to display the disc menu. To change original
and playlist on the TV screen.
8. Cursor K / L / { / B buttons
Press to select items or settings.
9. REV E button
• During playback, press to fast reverse playback.
• When playback is in pause, press to slow reverse
playback.
10. REC SPEED button
Press to switch the recording speed.
11. SKIP H button
• During playback, press to return to the beginning of
the current chapter, track or file.
• When playback is in pause, press repeatedly to
reverse the playback step by step.
12. Bx1.3/0.8 button
During playback, press to play back in a slightly
faster/slower while keeping the audio quality just as
normal playback.
13. REC/OTR button
• Press once to start a recording.
• Press repeatedly to start the one-touch timer
recording.
14. OPEN/CLOSE A button*
Press to open or close the disc tray.
15. INPUT SELECT button
Press to select the appropriate input.
16. AUDIO button
• Press to display the audio menu during playback.
17. REPEAT button
Press to display the repeat menu.
Introduction
FUNCTIONAL OVERVIEW
Español
EN
13
FUNCTIONAL OVERVIEW
Front Panel Display
2
1
PM
BS CS
DR
CD
VCR
DB HDD
DVD
3
4
1.
PM
3. Current status of the unit
: Appears in the afternoon
with the clock display.
2. Title / track / file and chapter mark
: Appears when indicating a
title / track / file number.
: Appears when indicating a
chapter number.
: Appears when playback is
paused.
: Appears when playing back
a disc.
: Appears when the timer
programming or OTR has
been set and is proceeding.
: Flashes when all timer
recordings have been
finished.
4. Displays the following
• Elapsed playback time
• Current title / chapter / track /
file number
• Recording time / remaining time
• Clock
• Selected external input position
• Remaining time for one-touch
timer recording
: Appears during recording
process.
: Flashes when a recording
pauses.
: Appears when a disc is in
this unit.
Display Message
Appears when the disc tray is
opening.
Appears when the disc tray is
closing.
Appears when a disc is loaded
on the disc tray.
14
EN
Appears when data is being
written on a disc.
This section describes how to connect this unit to an external tuner such as cable/satellite box.
UHF
• When you change the connections, all devices shouldVHF
be/ turned
off.
antenna
• Refer to the operation manual accompanying external devices for more information.
2
Disconnect
Disconnect the power cords of the devices from
the
AC
outlet.
or
RF coaxial cable
Cable TV
company
disconnect
Connections
1
2
rear of your TV
ANT. IN
Make the connection as illustrated below.
e.g.)
Basic Setup
rear of your TV
RF coaxial cable
VIDEO IN
TV signal
AUDIO IN
R
Introduction
CONNECTION TO AN EXTERNAL TUNER
L
ANT. IN
Disc
Management
RCA video cable
RF coaxial cable
RCA audio cable
S-video cable
AUDIO OUT
R
L
VIDEO
OUT
S-VIDEO
OUT
VIDEO VIDEO
IN
OUT
RCA video cable
IN
L
L
Y
OUT
PB/CB
R
RCA audio cable
AUDIO IN
(L1)
R
IN
S-VIDEO AUDIO OUT
PR/CR
COMPONENT
VIDEO OUT
OUT
Recording
or
S-VIDEO
VIDEO VIDEO
IN
OUT
external tuner
L
L
Y
PB/CB
R
R
IN
AUDIO IN
(L1)
S-VIDEO AUDIO OUT
PR/CR
COMPONENT
VIDEO OUT
OUT
COAXIAL
S-VIDEO
DIGITAL AUDIO OUTPUT
PCM / BITSTREAM
rear of this unit
Playback
Supplied cables used in this connection are as follows:
• RCA audio cable (L/R) x 1
• RCA video cable x 1
Please purchase the rest of the necessary cables at your local store.
Note
4
After making the connection as described above, make
sure to select the appropriate video input type by
following the steps in “SETTINGS FOR THE VIDEO INPUT”
on page 16.
connect
Others
3
IN
VIDEO
IN
Y
L
VIDEO
OUT
HDMI OUT
L
PB/CB
R
R
IN
OUT
ANTENNA
AUDIO IN
OUT
S-VIDEO
COAXIAL
PR/CR
COMPONENT
VIDEO OUTPUT
AUDIO OUT
Function Setup
rear of your TV
Plug in the power cords of the devices to the AC outlet.
Editing
• Required cables and connecting methods differ depending on the external tuner.
For more information, please contact your external tuner provider.
With this setup:
• You can record any unscrambled channel by selecting the channel on the external tuner. Be sure that the external
tuner is turned on.
• Signal from the external tuner can be output only on CVBS output even when the power of the unit is off.
• You cannot record one channel while watching another channel.
DIGITAL AUDIO OUTPUT
PCM / BITSTREAM
rear of this unit
Note to CATV system installer
EN
15
Español
• This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electrical
Code, which provides guidelines for proper grounding - in particular, specifying that the cable ground shall be
connected to the grounding system of the building, as close to the point of cable entry as possible.
SETTINGS FOR THE VIDEO INPUT
You must let the unit know which video input jack you are using before making a recording.
POWER
OPEN/CLOSE
ZOOM
TIMER
PROG.
.@/:
ABC
DEF
INPUT SELECT
GHI
JKL
MNO
AUDIO
PQRS
TUV
WXYZ
REPEAT
DISPLAY
SPACE
CLEAR
SETUP
RETURN
ENTER
TOP MENU MENU/LIST
REC SPEED
X1.3/0.8
REV
SKIP
PLAY
PAUSE
REC/OTR
STOP
DVD RECORDER
NB089
FWD
1
2
3
4
5
Press [SETUP].
Use [K / L] to select “General
Setting”, then press [ENTER].
Use [K / L] to select “Video”, then
press [ENTER].
Use [K / L] to select “Select Video”,
then press [ENTER].
Use [K / L] to select desired external
input position, then press [ENTER].
General Setting
Playback
Display
Video
Recording
Clock
Reset All
SKIP
CM SKIP
6
Progressive
TV Aspect
Select Video
Select Video
L1 (Rear)
L2 (Front)
Use [K / L] to select the input jack
type to connect, then press [ENTER].
If you want to use VIDEO IN jack, select “Video
In”.
If you want to use S-VIDEO IN jack, select
“S-Video In”.
General Setting
Playback
Display
Video
Recording
Clock
Reset All
7
16
EN
Progressive
TV Aspect
Select Video
L2Select
(Front)Video
In
L1Video
(Rear)
L2S-Video
(Front) In
Press [SETUP] to exit.
Introduction
CONNECTION TO A TV
Make one of the following connections, depending on the capabilities of your display device.
TV
Method 2
Method 3
standard picture
good picture
better picture
VIDEO
IN
rear of your TV
COMPONENT
VIDEO IN
S-VIDEO IN
Y
AUDIO IN
R
and
PB/CB
(Blue)
PR/CR
(Red)
S-video cable
or
or
component
video cable
VIDEO
OUT
L
OUT
L
Y
(Blue)
PB/CB
(Red)
S-VIDEO
R
IN
R
S-VIDEO AUDIO OUT
COAXIAL
DIGITAL AUDIO OUTPUT
PCM / BITSTREAM
R
AUDIO OUT
R
PR/CR
AUDIO OUT
VIDEO OUT
COMPONENT
VIDEO OUT
S-VIDEO OUT
COMPONENT
VIDEO OUTPUT
After you have completed the connections
• Switch the input selector on your TV to an appropriate external input channel. Press a button on the TV’s original
remote control that selects an external input channel until the DVD recorder’s opening picture appears. Check your
TV owner’s manual for details.
• Connect this unit directly to the TV. If the RCA audio/video cables are connected to a VCR, pictures may be
distorted due to the copy protection system.
• When “Progressive” is set to “ON”, no video signal will be output from the VIDEO OUT or S-VIDEO OUT jack.
Editing
Note
Playback
Supplied cables used in this connection are as follows:
• RCA audio cable (L/R) x 1
• RCA video cable x 1
Please purchase the rest of the necessary cables at your local store.
Recording
AUDIO OUT
Disc
Management
(Green)
VIDEO
OUT
VIDEO VIDEO
IN
OUT
AUDIO IN
(L1)
Basic Setup
RCA
video cable
L
L
(Green)
L
RCA
audio cable
this unit
Connections
analog audio
Method 1
Function Setup
To set progressive scan mode, refer to page 78
• This unit is compatible with the progressive scan system. The feature provides you the higher quality images than the
traditional output system. To utilize this feature, you must set “Progressive” to “ON”.
Others
Español
EN
17
CONNECTION TO AN AUDIO SYSTEM
2 Channel Analog Audio Connection
Digital Audio Connection
stereo system
Dolby Digital decoder
audio
AUDIO IN
R
L
COAXIAL
digital audio
coaxial input jack
analog audio
input jacks
digital audio coaxial cable
RCA audio cable
VIDEO VIDEO
IN
OUT
L
L
VIDEO VIDEO
IN
OUT
Y
L
this unit
PB/CB
R
AUDIO IN
(L1)
IN
R
S-VIDEO AUDIO OUT
OUT
PR/CR
COMPONENT
VIDEO OUT
L
PB/CB
R
COAXIA
DIGITAL AUDIO O
PCM / BITSTR
S-VIDEO
AUDIO OUT
Y
AUDIO IN
(L1)
IN
R
S-VIDEO AUDIO OUT
PR/CR
COMPONENT
VIDEO OUT
OUT
COAXIAL
S-VIDEO
DIGITAL AUDIO OUTPUT
PCM / BITSTREAM
DIGITAL AUDIO OUTPUT
*MD deck or DAT deck can be also connected through coaxial jack.
Supplied cables used in this connection are as follows:
• RCA audio cable (L/R) x 1
Please purchase the rest of the necessary cables at your local store.
Multi Channel Digital Audio Setting
Setting
Connection
If output is Dolby Digital encoded audio, connect to
a Dolby Digital decoder.
Setup >General Setting >Playback >Audio Out >
Dolby Digital
Stream
Connecting to an MD deck or DAT deck.
PCM
If not connected to any external devices.
PCM
* To complete these settings, refer to page 73.
Note
• The audio source on a disc in a Dolby Digital multi channel surround format cannot be recorded as digital sound
by an MD or DAT deck.
• By connecting this unit to a Dolby Digital decoder, you can enjoy high-quality Dolby Digital multi channel
surround sound as heard in the movie theaters.
• Playing back a DVD using incorrect settings may generate noise distortion and may also damage the speakers.
18
EN
This unit uses the following on-screen displays and menus to guide you to the easy operations.
The on-screen displays give you the information on the loaded disc, the disc/file in playback, etc.
The menus allow you to change the various kinds of settings for playing back, recording, or editing to suite your preference.
The on-screen display changes in the following order
as you press [DISPLAY].
Disc Information / Menu
5
OFF
1/ 5
2
1/ 5
0:01:00 / 1:23:45
-RW
VR
ORG
Basic Setup
Disc Information/Menu
L1 (Rear)
6
1
3
SP
7
1:53
4
* This is an example screen only for explanation.
: Marker
: Audio
: Noise Reduction
: Subtitle
: Zoom
: Angle
: Surround
Playback
: Search
Recording
1. Indicates a disc type and format mode.
2. Indicates a type of titles for VR mode DVD-RW .
3. Indicates the selected external input position.
4. Indicates a recording speed and possible recording
time left.
5. Indicates a title number, chapter number, elapsed time
and total time of disc playback.
6. Each icon means:
Disc
Management
Title Name Information
(only when VR mode DVD-RW/-R, or
unfinalized Video mode DVD-RW/-R is in playback)
or
File Name Information
(only when a CD with MP3/JPEG/Kodak Picture CD files
is in playback)
Connections
On-Screen Display / Menu
Introduction
GUIDE TO ON-SCREEN DISPLAYS AND MENUS
: Repeat
7. Indicates an operation status.
Editing
Note
• In some descriptions on this manual, only one disc
type is indicated as an example.
Function Setup
Title/File Name Information
1. Displays title/file name.
Title name information
Title Name
My Title
Others
1
File name information
File Name
My File
Español
1
EN
19
GUIDE TO ON-SCREEN DISPLAYS AND MENUS
Main Menu
Press [SETUP] to display the main menu. Then use
[K / L] to select a menu and press [ENTER] to display the
menu. These menus provide entries to all main functions
of the unit.
Setup
1
2
3
4
5
General Setting
Timer Programming
Title List
DVD Menu
CD Playback Mode
1. General Setting:
To go to general setting menu.
2. Timer Programming:
To program a timer recording.
3. Title List:
To call up the title list.
4. DVD Menu:
To set up the DVD setting.
5. CD Playback Mode:
To set up the CD playback setting.
• “CD Playback Mode” is available only when an audio
CD, a CD-RW/-R with MP3 / JPEG / Kodak Picture CD
files is inserted into the unit.
General Setting Menu
General Setting
1
2
3
4
5
6
2
Playback
Display
Video
Recording
Clock
Reset All
1. Playback:
To set up the unit to play back discs as you prefer.
2. Display:
To set up the OSD screen as you prefer.
3. Video:
To set up the video setting.
4. Recording:
To set up the unit to record to discs as you prefer.
5. Clock:
To set up the clock of the unit as you need.
6. Reset All:
To reset the setting to the factory default.
DVD Menu / CD Playback Mode
<DVD Menu menu>
DVD Menu
1
2
3
4
Format
Finalize
Disc Protect OFF ON
Delete All Playlists
<CD Playback Mode menu>
CD Playback Mode
5
1
6
2
7
3
20
EN
Random Play
Program Play
Slide Show
1. Format (DVD-RW only):
Allows you to format the disc.
2. Finalize:
Allows you to finalize a disc containing recorded titles.
3. Disc Protect (VR mode DVD-RW only):
Allows you to protect a disc from accidental editing or
recording.
4. Delete All Playlists (VR mode DVD-RW only):
Allows you to delete playlist.
5. Random Play:
Allows you to activate the random playback feature.
6. Program Play: (Audio CD only)
Allows you to activate the program playback feature.
7. Slide Show: (JPEG / Kodak Picture CD files only)
Allows you to select the display time of the slide show
mode.
You need to follow these steps when you turn on this unit
for the first time.
OPEN/CLOSE
.@/:
ABC
DEF
INPUT SELECT
GHI
JKL
MNO
AUDIO
PQRS
TUV
WXYZ
REPEAT
DISPLAY
SPACE
CLEAR
SETUP
RETURN
ENTER
TOP MENU MENU/LIST
Use [K / L] to select your desired
language, then press [ENTER] to set
language.
Initial Setting
OSD Language
English
Français
Español
3
Press [ENTER] to activate “Clock
Setting”.
Disc
Management
TIMER
PROG.
Turn on the TV. Select the input to
which the unit is connected.
Basic Setup
ZOOM
Press [POWER].
Initial Setting
Clock Setting
--- / -- / ---- (---)
-- : -- --
REV
PLAY
FWD
X1.3/0.8
SKIP
PAUSE
SKIP
STOP
CM SKIP
REC/OTR
4
Proceed to step 4 in “Clock Setting”
on page 22.
Recording
REC SPEED
Connections
POWER
1
2
Introduction
INITIAL SETTING
Playback
DVD RECORDER
NB089
Editing
Function Setup
Others
Español
EN
21
SETTING THE CLOCK
Set the clock before you try the timer programming.
Clock Setting
POWER
OPEN/CLOSE
ZOOM
TIMER
PROG.
.@/:
ABC
DEF
INPUT SELECT
GHI
JKL
MNO
AUDIO
PQRS
TUV
WXYZ
REPEAT
DISPLAY
SPACE
CLEAR
SETUP
RETURN
ENTER
TOP MENU MENU/LIST
REC SPEED
REV
PLAY
FWD
X1.3/0.8
SKIP
PAUSE
SKIP
STOP
CM SKIP
REC/OTR
1
2
3
Press [SETUP] and use [K / L] to
select “General Setting”, then press
[ENTER].
Use [K / L] to select “Clock”, then
press [ENTER].
“Clock” menu will appear.
Use [K / L] to select calendar or time,
then press [ENTER].
General Setting
Playback
Display
Video
Clock Setting
Recording
JAN / 01 / 2007 ( MON )
Clock
12 : 00 AM
Reset All
4
Use [{ / B] to select an item to set,
and use [K / L] to select the contents
to suit your preference, then press
[ENTER].
General Setting
Playback
Display
Video
Clock Setting
Recording
JAN / 01 / 2007 ( MON )
Clock
12 : 00 AM
Reset All
DVD RECORDER
Your setting will be activated.
The clock start counting when you press
[ENTER].
NB089
5
Note
• Your clock setting will be lost if either there is a power
failure or this unit has been unplugged for more than
30 seconds.
• For setting the day, year, hour and minute,
[the Number buttons] can also be used.
• You can set the built-in calendar from the year 2007
up to 2056.
22
EN
Press [SETUP] to exit.
Introduction
FORMATTING A DISC
Choosing the Recording Format of a Brand-New DVD-RW
Use [K / L] to select “DVD Menu”,
then press [ENTER].
Setup
General Setting
Timer Programming
Title List
DVD Menu
POWER
TIMER
PROG.
ABC
DEF
OPEN/CLOSE
INPUT SELECT
JKL
MNO
AUDIO
PQRS
TUV
WXYZ
REPEAT
DISPLAY
SPACE
CLEAR
SETUP
RETURN
ENTER
TOP MENU MENU/LIST
REV
PLAY
FWD
X1.3/0.8
SKIP
PAUSE
SKIP
STOP
CM SKIP
REC/OTR
NB089
Start
Format Mode
Use [K / L] to select “Video mode” or
“VR mode”, then press [ENTER].
Press [SETUP] to exit.
Editing
DVD RECORDER
Insert a brand-new disc.
Formatting will start.
Formatting
90%
Function Setup
5
6
7
8
DVD Menu
Format
Finalize
Playback
REC SPEED
4
Use [K / L] to select “Format Mode”,
then press [ENTER].
DVD Menu
Format
Finalize
Recording
GHI
3
Use [K / L] to select “Format”, then
press [ENTER].
Disc
Management
.@/:
ZOOM
Basic Setup
1
2
Press [SETUP].
Connections
When inserting a brand-new DVD-RW, the unit
automatically starts to initialize the disc.
DVD-RW will be formatted either video or VR mode
according to the recording format mode setting of the
unit. Before insert a brand-new DVD-RW, you need to set
the recording format to the desired mode. You can also
manually format a DVD-RW once it has been used.
Formatting is completed.
“100%” is indicated.
Others
Note
Español
• The recording format setting is effective only for
DVD-RW. You cannot change the recording format
for a DVD-R.
• You cannot mix 2 formats on one DVD-RW. If you
insert a disc that has been recorded before, the
recording format cannot be changed even if you
change it in the main menu.
EN
23
FORMATTING A DISC
Reformatting a Disc Manually
Insert a recordable disc.
If you are using a DVD-RW, you can format the disc by
performing “Format”. You can format DVD-RW for either
video mode recording or VR mode recording.
POWER
ZOOM
TIMER
PROG.
ABC
DEF
OPEN/CLOSE
1
2
Press [SETUP].
Use [K / L] to select “DVD Menu”,
then press [ENTER].
Setup
General Setting
Timer Programming
.@/:
Title List
INPUT SELECT
DVD Menu
GHI
JKL
MNO
AUDIO
PQRS
TUV
WXYZ
REPEAT
DISPLAY
SPACE
CLEAR
SETUP
RETURN
ENTER
TOP MENU MENU/LIST
REC SPEED
X1.3/0.8
REV
SKIP
PLAY
FWD
PAUSE
SKIP
STOP
CM SKIP
REC/OTR
DVD RECORDER
3
Use [K / L] to select “Format”, then
press [ENTER].
e.g.) VR mode DVD-RW
DVD Menu
Format
Finalize
Disc Protect OFF ON
Delete All Playlists
4
Use [K / L] to select “Start”, then
press [ENTER].
DVD Menu
Format
Finalize
Disc Protect OFF ON
Delete All Playlist
Start
Format Mode
Selection menu will appear and prompt you to
confirm.
5
NB089
Use [K / L] to select “Yes”, then press
[ENTER].
Formatting will start.
If you want to cancel formatting, select “No”.
DVD Menu
Format
Finalize
Start
Disc Protect OFF ON
Format Mode
Are you sure?
Delete All Playlist
Yes
No
6
Note
• When you reformat the disc, the contents of the disc
are erased.
• For DVD-RW, make sure that the recording format is
set to the desired mode. (See steps 1 to 6 in
“Choosing the Recording Format of a Brand-New
DVD-RW” on page 23.)
24
EN
Formatting is completed.
“100%” is indicated.
Formatting
100%
Setting for Auto Chapter
Introduction
PREPARING A DISC
Setting Aspect Ratio for Video Mode
Recording
You can set a specified time for chapter marks.
2) Use [K / L] to select “Recording”, then press
[ENTER].
“Recording” menu will appear.
4) Use [K / L] to select a desired time option, then
press [ENTER].
Auto Chapter
Auto Finalize
Auto Chapter
Aspect Ratio (Video mode)
OFF Make Recording Compatible
5 minutes
10 minutes
15 minutes
30 minutes
60 minutes
1) Press [SETUP] and use [K / L] to select “General
Setting”, then press [ENTER].
2) Use [K / L] to select “Recording”, then press
[ENTER].
“Recording” menu will appear.
3) Use [K / L] to select “Aspect Ratio (Video mode)”,
then press [ENTER].
4) Use [K / L] to select your desired setting, then press
[ENTER].
General Setting
Recording
Playback
Display
Auto Chapter
Video
Auto Finalize
Aspect Ratio (Video
mode)
Recording
Aspect Ratio (Video mode)
Auto
Clock
Make Recording Compatible
4:3
Reset All
16 : 9
5) Press [SETUP] to exit.
Note
Auto (default): It will be recorded with whichever the
ratio that the program you started to record are
broadcasted with.
4:3 : Recorded in the aspect ratio of 4:3.
16:9 : Recorded in the aspect ratio of 16:9.
Playback
• The interval for auto chapter marks may slightly
differ.
• A blank chapter may be created depending on the
remaining time of the disc.
Disc
Management
General Setting
Playback
Display
Video
Recording
Clock
Reset All
You can set aspect ratio for video mode recording.
Basic Setup
3) Use [K / L] to select “Auto Chapter”, then press
[ENTER].
Connections
1) Press [SETUP] and use [K / L] to select “General
Setting”, then press [ENTER].
5) Press [SETUP] to exit.
Note
Editing
• For DVD-RW VR mode, the image will be recorded in
whichever the ratio that the program you record are
broadcasted with, regardless of the “Aspect Ratio
(Video mode)” setting.
Function Setup
Others
Español
EN
25
SETTING A DISC TO PROTECT
To prevent accidental recording, editing or erasing the
titles, you can protect them from “DVD Menu”.
POWER
OPEN/CLOSE
ZOOM
TIMER
PROG.
.@/:
ABC
DEF
INPUT SELECT
GHI
JKL
MNO
AUDIO
PQRS
TUV
WXYZ
REPEAT
SPACE
DISPLAY
TOP MENU MENU/LIST
CLEAR
SETUP
RETURN
ENTER
REC SPEED
REV
PLAY
FWD
X1.3/0.8
SKIP
PAUSE
SKIP
REC/OTR
STOP
CM SKIP
1
2
3
Press [SETUP].
Use [K / L] to select “DVD Menu”,
then press [ENTER].
Use [K / L] to select “Disc Protect
OFF ON”, then press [ENTER].
e.g.) VR mode DVD-RW
DVD Menu
Format
Finalize
Disc Protect OFF ON
Delete All Playlists
4
Use [K / L] to select “Yes”, then press
[ENTER].
DVD Menu
Format
Finalize
Disc Protect OFF ON
Protect this disc?
Delete All Playlist
Yes
No
DVD RECORDER
NB089
A disc will be protected.
This operation may take
awhile to be completed.
Note
To cancel the disc protect:
• When you insert a disc protected with this unit,
“Disc Protect ON OFF” will appear instead of “OFF
ON”.
DVD Menu
Format
Finalize
Disc Protect ON
OFF
Delete All Playlist
To release the protect for the disc, select “Yes” at step 4.
26
EN
Auto Finalizing
OPEN/CLOSE
TIMER
PROG.
.@/:
ABC
DEF
INPUT SELECT
GHI
JKL
MNO
AUDIO
PQRS
TUV
WXYZ
REPEAT
DISPLAY
SPACE
CLEAR
SETUP
RETURN
ENTER
TOP MENU MENU/LIST
Use [K / L] to select “Recording”,
then press [ENTER].
“Recording” menu will appear.
Use [K / L] to select “Auto Finalize”,
then press [ENTER].
Use [K / L] to select “Disc Full” or
“End of Timer Rec”, then press
[ENTER].
Disc
Management
ZOOM
“General Setting” menu will appear.
General Setting
REV
PLAY
FWD
X1.3/0.8
SKIP
PAUSE
SKIP
STOP
CM SKIP
REC/OTR
5
DVD RECORDER
Use [K / L] to select “ON”, then press
[ENTER].
General Setting
Playback
Display
Video
Recording
Clock
Reset All
Playback
REC SPEED
Auto Chapter
Auto Finalize
Auto Finalize
Aspect Ratio (Video mode)
Disc Full Replace Disc Menu
End of Timer Rec
Recording
Playback
Display
Video
Recording
Clock
Reset All
Basic Setup
POWER
1
2
3
4
Press [SETUP] and use [K / L] to
select “General Setting”, then press
[ENTER].
Connections
You can finalize discs automatically using this function.
You can use this function to finalize discs after finishing
all timer recordings and at the end of the disc space.
Introduction
PLAYING THE DISCS IN OTHER DVD PLAYERS
Auto Chapter
Auto Finalize
AutoFull
Finalize
Disc
Aspect Ratio (Video mode)
Disc
Full Replace Disc Menu
ON
EndOFF
of Timer Rec
Editing
NB089
General Setting
Function Setup
Playback
Display
Video
Recording
Clock
Reset All
Auto Chapter
End
TimerAuto
RecFinalize
AutoofFinalize
Aspect Ratio (Video mode)
ON
Disc
Full Replace Disc Menu
EndOFF
of Timer Rec
Your setting will be activated.
Others
6
Press [SETUP] to exit.
Español
EN
27
PLAYING THE DISCS IN OTHER DVD PLAYERS
Finalizing a Disc
You will need to finalize discs to play back on other DVD
players.
Finalizing may take several minutes up to an hour.
Since the process of the finalization fills empty space of
the disc, a shorter recording period on the disc will
require a longer time period for finalization. Do not
unplug the power cord during finalization.
POWER
OPEN/CLOSE
ZOOM
TIMER
PROG.
.@/:
ABC
DEF
INPUT SELECT
GHI
JKL
MNO
AUDIO
PQRS
TUV
WXYZ
REPEAT
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST
RETURN
1
2
3
4
Press [SETUP].
Use [K / L] to select “DVD Menu”,
then press [ENTER].
“DVD Menu“ will appear.
Use [K / L] to select “Finalize”, then
press [ENTER].
Use [K / L] to select “Yes”, then press
[ENTER].
e.g.) VR mode DVD-RW
DVD Menu
Format
Finalize
Disc Protect OFF ON
Finalize disc?
Delete All Playlist
ENTER
Yes
No
REC SPEED
REV
PLAY
FWD
X1.3/0.8
SKIP
PAUSE
SKIP
STOP
CM SKIP
REC/OTR
Finalizing will start.
Finalizing
90%
DVD RECORDER
This operation may take
awhile to be completed.
NB089
5
28
EN
Finalizing is completed.
Note
Press [STOP C] during the finalizing is in progress. Use
[K / L] to select “Yes”, then press [ENTER]. Finalizing is
canceled and the unit switches to stop mode.
Do you want to cancel ?
Yes
No
Finalizing
ON
If “ ” appears when [STOP C] is pressed, you cannot
cancel finalizing because the finalizing has already
reached at a critical point in its process.
If “No” is selected and [ENTER] or [RETURN ] is
pressed, finalizing is continued.
You cannot cancel finalizing DVD-R once it has started.
Disc
Management
• DO NOT power off during finalizing. This may result
in a malfunction.
5%
Basic Setup
DVD Menu
Format
Undo Finalize
Disc Protect OFF
Delete All Playlists
Connections
• Finalizing a disc in video mode automatically creates
a DVD menu.
• Even after DVD-RW in VR mode is finalized, you can
still record or edit. After you finalize DVD-RW in video
mode or DVD-R, you cannot edit or record anything
else on that disc.
• If you insert a DVD-RW finalized with this unit, “Undo
Finalize” will appear instead of “Finalize” at step 3.
• To release the finalization of the DVD-RW disc, select
“Undo Finalize” at step 3.
To cancel finalizing...
(DVD-RW only)
Introduction
PLAYING THE DISCS IN OTHER DVD PLAYERS
Recording
Playback
Editing
Function Setup
Others
Español
EN
29
INFORMATION ON DVD RECORDING
Recording Speed
Restrictions on Recording
You can select a recording speed among 5 options, and
the recording time will depend on the recording speed
you select as follows.
Recording speed
XP / 1H
SP / 2H
LP / 4H
EP / 6H
SLP / 8H
Recording time
12cm
8cm
Video/
sound quality
60 min 18 min
120 min 36 min
240 min 72 min
360 min 108 min
480 min 144 min
• The recording times listed above are estimates and are
for reference purposes only. Actual recording times may
vary.
• The audio and video quality of content being recorded
may differ depending on the recording speed/recording
time chosen.
Note
• This unit cannot record to CD-RW or CD-R.
• DVD-RW/-R and CD-RW/-R recorded on a personal
computer or a DVD or CD recorder may not be
played back if the disc is damaged or dirty or if there
is condensation on the player’s lens.
• If you record a disc using a personal computer, even
if it is recorded in a compatible format it may not be
played back because of the settings of the
application software used to create the disc. (Check
with the software publisher for more detailed
information.)
• Discs recorded in video mode on this unit cannot
record additional information using other DVD
recorders.
• It is not possible to use a DVD-RW formatted with
this unit on other DVD recorder unless the content of
the disc was also recorded with this unit.
• Since the recording is made by the VBR (variable bit
rate) method, depending on the picture you are
recording, the actual remaining time for recording
may be a little shorter than the remaining time
displayed on the TV screen.
• “Make Recording Compatible” in “Recording”
menu does not work on this unit.
30
EN
You cannot record copy-protected video using this unit.
Copy-protected video includes DVD-videos and some
satellite broadcasts, some pay-per-view stations and
some “premium” stations.
If copy-protected material is detected, recording will
pause or stop automatically and an error message
appears on the screen.
“Copy-once only” video can only be recorded to CPRM
compatible DVD-RW formatted in VR mode.
What is “CPRM”?
CPRM is a copy protection system with scramble system
regarding the recording of “copy-once” broadcast
programs. CPRM stands for Content Protection for
Recordable Media.
This unit is CPRM compatible, which means that you
can record copy-once broadcast programs, but you
cannot make another copy of those recordings. CPRM
recordings can only be made on CPRM compatible DVDRW formatted in VR mode, and CPRM recordings can
only be played back on DVD players that are specifically
compatible with CPRM.
Making discs playable in other DVD players(Finalize)
For DVD-RW/-R, it is necessary to finalize the disc after
recording, in order to play back the disc on other DVD
players. (Refer to pages 27-29.)
When video mode DVD-RW or DVD-R are finalized, a DVD
menu is created. You cannot finalize discs in other DVD
recorders.
Follow the steps to record TV programs from an external
tuner.
This unit has no tuner system so cannot receive TV
broadcasts without external tuner or such devices.
OPEN/CLOSE
.@/:
ABC
DEF
INPUT SELECT
GHI
JKL
MNO
AUDIO
PQRS
TUV
WXYZ
REPEAT
DISPLAY
SPACE
CLEAR
SETUP
RETURN
ENTER
TOP MENU MENU/LIST
REV
PLAY
FWD
X1.3/0.8
SKIP
PAUSE
SKIP
STOP
CM SKIP
REC/OTR
3
Press [OPEN/CLOSE A] to close the
disc tray.
It may take awhile to load
the disc completely.
• When inserting a brand-new DVD-RW, the unit
automatically starts to format.
• If titles have been recorded on the disc, the
title list is displayed. Press [STOP C] to exit the
title list.
Playback
4
Press [REC SPEED] to select a
recording speed.
Recording
REC SPEED
Align the disc to
the disc tray guide.
Disc
Management
TIMER
PROG.
Press [OPEN/CLOSE A] to open the
disc tray and insert your disc with its
label facing up.
Basic Setup
ZOOM
Turn on the TV and be sure to select the input to
which the unit is connected.
Connections
POWER
1
2
Press [POWER].
Introduction
BASIC RECORDING & ONE-TOUCH TIMER RECORDING
Refer to “Recording Speed” on page 30.
DVD RECORDER
NB089
2:00
Press [INPUT SELECT] to select the
appropriate external input position
(L1/L2) to which your external tuner
is connected. Then select the desired
channel to record on the external
tuner.
Function Setup
5
Editing
SP
Others
EN
31
Español
Instructions continue on the next page.
BASIC RECORDING & ONE-TOUCH TIMER RECORDING
6
Press [REC/OTR] to start recording.
“I” will be displayed for 5 seconds.
7
Press [STOP C] to stop recording.
The recorded title will be included in the title list.
(Refer to “Guide to a Title List” on page 55.)
I
Press [PAUSE F] to pause recording.
Press [PAUSE F]] or [REC/OTR] again to restart
recording.
Wait for a moment.
90%
This operation may take
awhile to be completed.
To set one-touch timer recording (OTR)...
This is a simple way to set the recording time in blocks
of 30 minutes.
Press [REC/OTR] repeatedly until the desired recording
time (30 minutes to 8 hours) appears on the TV screen.
One-touch timer recording will start.
I
0:30
0:30
(normal recording)
8:00
1:00
7:30
• To change the recording length during one-touch
timer recording, press [REC/OTR] repeatedly until the
desired length appears.
• To cancel one-touch timer recording within the
specified time, press [STOP C].
Note
•
•
•
•
When you press [REC/OTR], recording starts immediately and continues until the disc is full or you stop recording.
When the unit clock has not been set, the space for a date and time of title names will be blank.
You cannot change the recording speed during the recording pause mode.
You can change a channel to be recorded during the recording pause mode.
Note for one-touch timer recording
• The remaining recording time will be displayed on the front panel display during one-touch timer recording. Press
[DISPLAY] to see it on the TV screen.
• Unlike the timer recording, you can perform the following operations during one-touch timer recording.
- Turning off the power (One-touch timer recording will be canceled.).
- Using [REC/OTR] or [STOP C] on the remote control.
• You cannot use the pause function during one-touch timer recording.
• When one-touch timer recording is finished and the power is turned off, the unit will switch to the timer-standby
mode automatically if a timer recording has been programmed. Press [POWER] to cancel the timer-standby mode
to use the unit continuously.
32
EN
OPEN/CLOSE
.@/:
ABC
DEF
INPUT SELECT
GHI
JKL
MNO
AUDIO
PQRS
TUV
WXYZ
REPEAT
DISPLAY
SPACE
CLEAR
SETUP
RETURN
ENTER
TOP MENU MENU/LIST
2
JAN/ 2/07 12:00 AM L1 SP
2H (1:00)
MON JAN/01 10:00AM
Date
JAN/02
Start
End
12:00AM 1:00AM
New Program
L1/L2
L1
1/1
4
5
1. Title of a timer program (Contains date, time, channel,
recording speed of the program)
2. Current date and time
3. Recording speed and length of the recording
4. Timer program list
5. Total number of pages and current page (2 pages maximum)
1
2
Press [TIMER PROG.].
Use [K / L] to select “New Program”,
then press [ENTER].
Timer Programming
Recording
TIMER
PROG.
1
Timer Programming
Disc
Management
ZOOM
3
Basic Setup
POWER
Guide to Timer Programming Display
Connections
You can program the unit to record up to 12 programs
within a month in advance. Daily or weekly program
recordings are also available.
Before recording, make sure
• Connect the external tuner to either L1 or L2 and set it
to output audio/video signals when it comes to the time
you want to start recording.
• Do not change the external tuner’s channel while you
are recording. You cannot watch one channel and
record another at the same time.
• Set the clock before setting a timer programming.
• Insert a recordable disc with enough recordable space.
Introduction
TIMER RECORDING
MON JAN/01 10:00AM
Date
REV
PLAY
FWD
X1.3/0.8
SKIP
PAUSE
SKIP
STOP
CM SKIP
L1/L2
Playback
REC SPEED
Start
End
New Program
1/1
REC/OTR
NB089
3
Use [K / L] to enter the date, then
press [B].
Start
--:-Speed
2H
End
--:--
2H
JAN/01
Daily
Note
MON-SAT
MON-FRI
2 : 00
When pressing [L] at
the current date, the
date will change as
follows.
e.g.) January 1st
SAT
Others
FRI
SUN
JAN/31
Instructions continue on the next page.
EN
33
Español
• If you have not set the clock yet:
“Clock Setting” menu will appear instead of the timer
programming list at step 1. Continue with the step 3
in “Clock Setting” on page 22 before setting a timer
programming.
• Use [s / B] to move the cursor to the left and the
right in “Timer Programming” menu.
• Timer recording will not work when the power is on.
• When power is on, programs registered for recording
in timer recording will be automatically cleared after
the end time and date have passed.
Function Setup
Date
JAN/02
L1/L2
L1
Editing
DVD RECORDER
• If there are 6 or more programs, use
[SKIP H / G] to change pages.
TIMER RECORDING
4
Use [K / L / { / B] or [the Number
buttons] to enter the start and end
time, then press [B].
Date
JAN/02
L1/L2
L1
Start
12 : 00AM
Speed
2H
End
--:--
2H
5
2 : 00
Use [K / L] to select the appropriate
external input position (L1/L2) to
which your external tuner is
connected, then press [B].
Date
JAN/02
L1/L2
L1
Start
12 : 00AM
Speed
2H
7
End
1 : 00AM
2H
1 : 00
8
Press [ENTER] when all items are
entered.
Your program setting will be stored.
• To set another program, repeat steps 2 to 7.
• To exit, press [TIMER PROG.] or [SETUP].
• When 2 or more programs are overlapped,
“Timer program overlapped” appears, and the
overlapped program will be displayed in blue.
To correct the timer program refer to
“Checking, canceling, or correcting the timer
programming information” on page 35.
Press [POWER] to set a timer
programming.
will appear on the front panel display, while this
unit waits to make the recording.
BS CS
6
Use [K / L] to select a recording
speed.
Date
JAN/02
L1/L2
L1
Start
12 : 00AM
Speed
2H
End
1 : 00AM
2H
1 : 00
Refer to “Recording Speed” on page 30.
• You can check the remaining recordable space
of the disc when you select the recording
speed.
Date
JAN/02
L1/L2
L1
Start
12 : 00AM
Speed
2H
End
1 : 00AM
2H
34
EN
1 : 00
DR
CD
HDD
Checking, canceling, or correcting the timer
programming information
1) Press [POWER].
If the timer program did not complete correctly,
the error number appears in the timer programming list.
Connections
will disappear on the front panel display.
Timer Programming
2) Press [TIMER PROG.].
TUE JAN/02 10:00AM
E41
3) Check the information on the list you want to edit.
Date
JAN/02
Start
End
12:00AM 1:00AM
New Program
Introduction
TIMER RECORDING
L1/L2
L1
Timer Programming
Date
JAN/02
Start
End
12:00AM 1:00AM
New Program
Basic Setup
JAN/ 2/07 12:00 AM L1 SP
2H (1:00)
MON JAN/01 10:00AM
1/1
L1/L2
L1
Each error number means:
1/1
To stop the timer recording in process
Already finalized
video format disc
E36
E25-28 Copy prohibited program E40
E29
Disc protected
E30
Disc full
Some portion has
not been recorded
because of program
overlapping.
Recording did not
start at the start time.
E31-32 Already 99 titles
recorded
E41
Power failed
E33
Already 999 chapters
recorded
E42
No disc when recording
E34
No space for Control
information
• A program with the error number is grayed in the timer
programming list.
• Once the timer programming list with error line(s) is
displayed, or after canceling and setting again the timer
standby mode, the program line(s) with error will be
cleared.
*1 PCA is a disc's space reserved for recording test.
Editing
Press [STOP C] on the front panel of the unit.
[STOP C] on the remote control is not effective.
Playback
6) Press [POWER] to return to the timer standby mode.
E23-24 Unrecordable disc
Recording
5) Press [TIMER PROG.] to exit.
PCA full *1
Disc
Management
4-A) To delete the timer program:
1 Use [K / L] to select the program you want to
delete, then press [ENTER].
2 Use [K / L] to select “Delete”, then press
[ENTER].
Selection menu will appear.
3 Use [K / L] to select “Yes”, then press [ENTER].
4-B) To correct the timer program:
1 Use [K / L] to select the program you want to
correct, then press [ENTER].
2 Use [K / L] to select “Program Change”, then
press [ENTER].
3 Correct the timer program by using
[K / L / { / B], then press [ENTER].
E1-22 Recording error other E35
E37-39 than below
Note
Function Setup
• Press [TIMER PROG.] to check the timer recording in
progress.
When the timer recording is proceeding, that
program will be highlighted with red. In this case,
you cannot select any other program.
Others
Español
EN
35
TIMER RECORDING
Hints for Timer Recording
• If there is a power failure or this unit has been unplugged for more than 30 seconds, the clock setting and all timer
programming will be lost.
• If a disc is not inserted,
flashes and timer recording cannot be performed. In some cases,
will appear
momentarily around the start point as the unit attempts to record. Please insert a recordable disc.
flashes. To play back or eject the recorded disc, press
• When all the timer recording is completed,
[POWER] first, then select the recorded title and press [PLAY B], or [OPEN/CLOSE A] to remove the disc.
• During timer recording or timer standby mode ( will appear), any operations on the unit will not be available. To make
these operations available, press [STOP C] on the front panel to cancel the timer recording or [POWER] to release timer
standby mode ( will disappear).
• To cancel the timer standby mode, press [POWER].
• When the starting and the ending time are the same, the length of the recording will be set for 24 hours. When the
disc becomes full during the recording, the unit turns itself off.
• When the programmed starting and ending time are earlier than the current time, the setting will not be accepted
and be cleared for redoing.
• If the starting time is earlier and the ending time is later than the current time, the recording will start right after you
turn the power off.
The Priority of Overlapped Settings
• Timer program which has the earlier start time will be placed first in the timer program list, and be given priority over
the programs with the later start time when timer programs overlap.
• When timer programs overlap, the first 2 minutes (at the longest) of the later recording will be cut off.
• When 2 or more timer programs have the same start time, the program set first will be given priority.
• A timer recording of lower priority will be canceled or start from the middle.
• Check the overlapped timer programmings and change the priority if necessary.
When the starting time is the same:
A program set previously (PROG. A) has priority.
PROG. A
PROG. B
actual
PROG.
PROG.AA
PROG. B
recording
The first 2 minutes (at the longest) will be cut off.
Note for DVD recording
• When the recording time of 2 programs are overlapped, or
the end time of a program and the start time of another
program is the same, the first 2 minutes (at the longest) of
the subsequent program will be cut off.
• If the cut-off portion comes up to 3 minute or more, this
program will be displayed with error number E40 in the
timer programming list.
When the end time of the programming
currently being recorded and the start time
of the subsequent program are same:
The beginning of the PROG. B may be cut off.
PROG. A
PROG. B
actual
recording
PROG. A
PROG. B
The first 2 minutes (at the longest) will be cut off.
36
EN
Use [K / L] to select “Satellite Link”,
then press [ENTER].
Timer Programming
Timer Programming
Satellite Link
OPEN/CLOSE
TIMER
PROG.
.@/:
ABC
DEF
INPUT SELECT
GHI
JKL
MNO
AUDIO
PQRS
TUV
WXYZ
REPEAT
DISPLAY
SPACE
CLEAR
SETUP
Recording
ZOOM
Satellite Link
Start
Speed
5:00PM
2H
Disc
Management
4
Use [K / L] to select the time and
recording speed, then press [ENTER].
Use [K / L] to select “Timer
Programming”, then press [ENTER].
Basic Setup
POWER
1
2
3
Press [SETUP].
Connections
You can set the unit to start recording whenever it
detects the video signal from the external tuner.
Preparing for the satellite link timer recording:
Preparation on the tuner
• Satellite link accepts only the connection from L1 (rear)
with the external tuner. (The connection from L2 cannot
read any signals from the external tuner.)
• The external tuner should be equipped with some kind
of timer function. Using timer function of the tuner, set
it to output audio/video signals when it comes to the
time you want to start recording, and stop output audio/
video signals when it comes to the time you want to
finish recording. Refer to the tuner’s manual on how to
set the timer.
• Make sure to set the satellite link standby mode when
you finish setting.
Introduction
SATELLITE LINK
To Standby Mode
TOP MENU MENU/LIST
RETURN
ENTER
PLAY
FWD
X1.3/0.8
SKIP
PAUSE
SKIP
STOP
CM SKIP
REC/OTR
6
• The hour can be selected from 1 to 12 with AM
or PM.
• Repeat procedures in step 5 to set the desired
minutes.
• If you wish to go back to the left, press [{].
Use [K / L] to select the recording
speed.
Function Setup
DVD RECORDER
5
Editing
REV
Playback
REC SPEED
Use [K / L] to set the desired starting
time, then press [B].
Refer to page 30 for details.
NB089
Others
EN
37
Español
Instructions continue on the next page.
SATELLITE LINK
7
8
Press [ENTER].
“To Standby Mode” is highlighted.
Press [ENTER] again.
Satellite Link
Start
Speed
5:00PM
2H
To Standby Mode
In a second, the unit will be turned off
automatically as it goes into the satellite link
standby mode.
To cancel the satellite link function while in
the satellite link standby mode:
Press [POWER] to turn on the unit.
To cancel the satellite link function while the
satellite link recording is in progress:
Press [STOP C] on the front panel of the unit.
Note
• If the signal of external input breaks up over 5 seconds, satellite link function will be canceled.
• If you have not set the clock, “Clock Setting” menu will appear at step 3. Follow to step 3 in “Clock Setting” on
page 22.
• You cannot set the end time for the satellite link timer recording on this unit.
• Recording picture will be distorted if the copy protection signal is being detected during satellite link timer
recording.
• You can record the satellite link by using S-video input jacks on the rear panel. Refer to page 39 for more
information.
• When a regular timer recording and the satellite link timer recording are overlapped, those recordings are
recorded as illustrated below.
• Press [TIMER PROG.] during the satellite link timer recording to check the satellite link timer recording in
progress.
example 2
example 1
example 3
timer
recording
timer
recording
timer
recording
satellite link
satellite link
satellite link
actual
recording
actual
recording
actual
recording
The first 2 minutes (at the longest) will be cut off.
38
EN
The first 2 minutes (at the longest) will be cut off.
Connection to an External Device
Introduction
SETTINGS FOR AN EXTERNAL DEVICE
Connect the external device properly to either L2 (front) or L1 (rear) input jacks of this unit by using S-video or RCA
audio / video cables.
Connections
or
S-VIDEO
OUT
VIDEO
OUT
AUDIO OUT
L
R
VIDEO
OUT
external device
AUDIO OUT
L
R
S-VIDEO
OUT
(camcorder, VCR etc.)
or
RCA
video
cable
RCA
audio
cable
RCA
video
cable
RCA
audio
cable
Basic Setup
S-video
cable
S-video
cable
or
VIDEO VIDEO
IN
OUT
L
L
Y
PB/CB
AUDIO IN
(L1)
L2
R
IN
S-VIDEO AUDIO OUT
OUT
PR/CR
COMPONENT
VIDEO OUT
Disc
Management
R
or
S-VIDEO
L1
to L2 IN
to L1 IN
VIDEO VIDEO
UT
IN
OUT
L
L
R
R
Y
PB/CB
AUDIO IN
(L1)
IN
S-VIDEO AUDIO OUT
PR/CR
COMPONENT
VIDEO OUT
OUT
COAXIAL
S-VIDEO
DIGITAL AUDIO OUTPUT
PCM / BITSTREAM
rear of this unit
After making the connection as described above, make sure to select the appropriate video input type by following the
steps in “SETTINGS FOR THE VIDEO INPUT” on page 16.
Playback
Supplied cables used in this connection are as follows:
• RCA audio cable (L/R) x 1
• RCA video cable x 1
Please purchase the rest of the necessary cables at your local store.
Recording
front of this unit
Note
• When connecting an external device of monaural output to this unit, use AUDIO L jack of L2 (Front).
Editing
Function Setup
Others
Español
EN
39
SETTINGS FOR AN EXTERNAL DEVICE
Recording from an External Device
Before recording from an external device, refer to the
instructions for the connection on page 39.
POWER
OPEN/CLOSE
ZOOM
TIMER
PROG.
.@/:
ABC
DEF
INPUT SELECT
GHI
JKL
MNO
AUDIO
PQRS
TUV
WXYZ
REPEAT
DISPLAY
SPACE
CLEAR
SETUP
RETURN
ENTER
TOP MENU MENU/LIST
REC SPEED
REV
PLAY
FWD
X1.3/0.8
SKIP
PAUSE
SKIP
STOP
CM SKIP
REC/OTR
5
6
7
8
DVD RECORDER
NB089
23
4
8
6
1
40
EN
1
2
3
4
Turn on the TV and press
[POWER], and be sure to select the
input of the TV to which the unit is
connected.
Press [OPEN/CLOSE A] to open the
disc tray. Place the disc to record on
properly.
Press [OPEN/CLOSE A] to close the
disc tray.
It takes awhile to load
the disc.
Select the input of the unit which the
external device is connected. (L1 or
L2)
• To use the input jacks on the rear of this unit;
Select “L1” by using [INPUT SELECT] or
[INPUT].
• To use the input jacks on the front of this unit;
Select “L2” by using [INPUT SELECT] or
[INPUT].
Press [REC SPEED] to select a
recording speed.
Refer to “Recording Speed” on page 30.
Press [REC/OTR] on the unit to start
recording.
Start playback on the external device
to record from.
Press [STOP C] on the unit to stop
recording.
This operation may take
awhile to be completed.
Introduction
INFORMATION ON PLAYBACK
Structure of Disc Contents
DVD video
Title:
title 1
title 2
chapter 1 chapter 2 chapter 1 chapter 2 chapter 3
Chapter:
audio CD
track 1
track 2
track 3
track 4
track 5
MP3 / JPEG
folder 1
file 1
file 2
folder 2
file 3
file 4
Disc
Management
Each title, chapter, or track, folder or file is assigned a
number, which is called “title number”, “chapter number”,
“track number”, “folder number” or “file number”
respectively.
Some discs may not have these numbers.
Basic Setup
Track:
Folder:
Divided contents of a DVD video disc.Roughly
corresponds to a story title in short stories.
Divided contents of a title. This corresponds to
a chapter in a story.
Divided contents of an audio CD.
Divided contents of a MP3/JPEG data disc.
Consists of number of files.
Connections
The contents of DVD are generally divided into titles, and the titles are subdivided into chapters.
Audio CDs are divided into tracks.
Data disc contains MP3/JPEG are divided into folders, and the folders are subdivided into files.
file 5
Recording
Playback
Editing
Function Setup
Others
Español
EN
41
BASIC PLAYBACK
Direct Playback
POWER
OPEN/CLOSE
ZOOM
TIMER
PROG.
.@/:
ABC
DEF
INPUT SELECT
GHI
JKL
MNO
AUDIO
PQRS
TUV
WXYZ
REPEAT
DISPLAY
SPACE
CLEAR
SETUP
RETURN
ENTER
TOP MENU MENU/LIST
REC SPEED
REV
PLAY
FWD
X1.3/0.8
SKIP
PAUSE
SKIP
REC/OTR
STOP
CM SKIP
DVD RECORDER
NB089
Note
• Some discs may start playback automatically.
42
EN
1
2
Press [POWER].
Turn on the TV and be sure to select the input to
which the unit is connected.
Press [OPEN/CLOSE A] to open the
disc tray and insert your disc with its
label facing up.
Align the disc to
the disc tray guide.
3
4
5
Press [OPEN/CLOSE A] to close the
disc tray.
It may take awhile to load
the disc completely.
Press [PLAY B] to start playback.
If you are playing back a DVD-video, a menu
may appear.
Refer to “Using the Title/Disc Menu” on page 45.
Press [STOP C] once to stop playback
temporarily.
• Refer to “Resume Playback” on page 46.
Introduction
BASIC PLAYBACK
Playback from the Title List
OPEN/CLOSE
.@/:
ABC
DEF
INPUT SELECT
GHI
JKL
MNO
AUDIO
PQRS
TUV
WXYZ
REPEAT
DISPLAY
SPACE
CLEAR
SETUP
RETURN
ENTER
TOP MENU MENU/LIST
REV
PLAY
FWD
X1.3/0.8
SKIP
PAUSE
SKIP
STOP
CM SKIP
REC/OTR
3
Press [OPEN/CLOSE A] to close the
disc tray.
It may take awhile to load
the disc completely.
Title list will appear automatically.
• To exit the title list, press [STOP C].
• To resume the title list, press [TOP MENU].
Use [K / L / { / B] to select a desired
title, then press [ENTER].
e.g.) VR mode DVD-RW original
ORG
Title List
JAN/ 1/07 12:00AM CH10 SP
12:00AM (0:12:00) JAN/ 1/07
DVD RECORDER
Playback
4
Recording
REC SPEED
Align the disc to
the disc tray guide.
Disc
Management
TIMER
PROG.
Basic Setup
ZOOM
Press [OPEN/CLOSE A] to open the
disc tray and insert your disc with its
label facing up.
Connections
POWER
1
2
Press [POWER].
Turn on the TV and be sure to select the input to
which the unit is connected.
CH10 SP
1
2
3
4
5
6
NB089
Editing
1/6
ORG
Function Setup
5
Use [K / L] to select “Play From
Start”, then press [ENTER].
Title List
JAN/ 1/07 12:00AM CH10 SP
12:00AM (0:12:00) JAN/ 1/07
1
4
2
Play From Start
Edit
Title Delete
5
Add To Playlist
CH10 SP
3
6
Note
1/2
Others
Playback will start.
6
Press [STOP C] once to stop playback
temporarily.
• Refer to “Resume Playback” on page 46.
To eject the disc, press [OPEN/CLOSE A] to
open the disc tray, then remove the disc before
turning off the unit.
EN
43
Español
• Some discs may start playback automatically.
• You can also start playback by pressing [PLAY B]
instead of [ENTER] at step 5.
• At step 4, you can press [SKIP G], or press [B]
when the title on the lower right of the title list is
highlighted to display the next page, and press
[SKIP H], or press [{] when the title on the upper
left of the title list is highlighted to display the
previous page.
BASIC PLAYBACK
Playing Back an Audio CD and a CD-RW/-R with MP3 / JPEG Files
POWER
OPEN/CLOSE
ZOOM
TIMER
PROG.
.@/:
ABC
DEF
INPUT SELECT
GHI
JKL
MNO
AUDIO
PQRS
TUV
WXYZ
REPEAT
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
REC SPEED
REV
PLAY
FWD
X1.3/0.8
SKIP
PAUSE
SKIP
STOP
CM SKIP
REC/OTR
DVD RECORDER
NB089
Press [OPEN/CLOSE A] to close the
disc tray.
It may take awhile to load
the disc completely.
File list will appear automatically.
• To exit the file list, press [STOP C].
• To resume the file list, press [TOP MENU].
3
Use [K / L] to select a desired folder
or track/file, then press [ENTER].
File List
DISC NAME
A
B
1
2
3
4
5
6
JPEG file1
JPEG file2
MP3 file1
MP3 file2
MP3 file3
MP3 file4
1/ 2
When selecting track/file:
Playback will start.
When selecting folder:
The files in the folder will appear.
Use [K / L] to select the file or folder you want to play
back, then press [ENTER].
• Press [PLAY B], [ENTER] or [B] to move to any lower
hierarchies.
• Press [s] or [RETURN ] to move back to the previous
hierarchy.
Hints for audio CD tracks and MP3 / JPEG files:
.
• Folders are shown by
.
• Audio CD tracks are shown by
• MP3 files are shown by 3 .
.
• JPEG files are shown by
• The system can recognize up to 255 folders and, up to
99 tracks/999 files.
• Letters of a file/folder name overflowing the given space
will be displayed as “…”.
• If there are no files in the folder, “No Files” will be displayed.
Note
• The audio source of MP3 files cannot be recorded as
digital sound by an MD or DAT deck.
• Files whose extension is other than “.mp3(MP3)” or
“.jpg / .jpeg(JPEG)” will not be listed.
• Some unplayable folders or files may be listed due to
the recording status.
• High-resolution JPEG files take longer to be displayed.
• Progressive JPEG files (JPEG files saved in progressive
format) cannot be played back on this unit.
• The JPEG pictures can also rotate by using
[K / L / { / B].
44
1
2
Follow steps 1 to 2 in “Direct
Playback” on page 42.
EN
It is recommended that files to be played back in this
unit are recorded under the following specifications:
<MP3>
• Sampling frequency
: 44.1 kHz or 48 kHz.
• Constant bit rate
: 112 kbps - 320 kbps
<JPEG>
• Upper limit
: 6,300 x 5,100 dots.
• Lower limit
: 32 x 32 dots.
• File size of image maximum : 12 MB.
Playing Back an Audio CD and a CDRW/-R with MP3 JPEG Files (cont’d)
Kodak Picture CD
DVD may contain a title list, which describes the contents
of the disc, or a disc menu, which guides you through the
available functions in the disc.
1) Press [MENU/LIST] or [TOP MENU] to call up the title
list or disc menu.
2) Use [K / L / { / B] to make a selection, and then
press [ENTER] to enable your selection.
Image 1
3) Press [STOP C] to exit the disc menu.
1
2
3
4
5
6
Basic Setup
Picture CD
Using the Title / Disc Menu
Connections
The Picture CD is a service to convert photographs taken
by a conventional film camera into digital data and write
the data on a CD. You can enjoy picture images on the TV
set by playing back the Picture CDs.
For details of Kodak Picture CD, contact a shop that
provides developing service of Kodak Inc.
1) Press [TOP MENU].
Introduction
BASIC PLAYBACK
Note
Pause
1) During playback, press [PAUSE F].
Playback will be paused and sound will be muted.
Playback
2) Use [K / L / { / B] to select a desired track to be
played back, then press [PLAY B] or [ENTER].
An image will be played back from the selected track
and go to the next one in turn.
Recording
• To exit the Picture CD thumbnail List, press [TOP
MENU] again or press [STOP C].
Arrow icons mean the title list includes a next or
previous page. Use [{ / B] in the direction of the
icon you wish to follow. You can also quick review the
six thumbnails at once between the first and last
pages by pressing [SKIP H / G].
Disc
Management
1/2
• You can select a numbered menu with [the Number
buttons] also.
• Menus vary among discs. Refer to the information
accompanying the disc for details.
• [MENU/LIST] or [TOP MENU] will not always
effective for all DVDs.
3) Press [STOP C] to stop playback.
Notes on JPEG and Kodak Picture CD:
F
2) Press [PLAY B] to return to the normal playback.
Editing
• After track is displayed for 5 seconds or 10 seconds
(set in the “Slide Show” on page 52) the display
moves to the next track.
During JPEG or Kodak Picture CD playback, press [B]
or [{] to rotate a picture 90 degrees clockwise or
counterclockwise respectively.
(Not available when the display menu appears.)
Note
Function Setup
• For DVD, set “Still Mode” to “Field” in “Playback”
menu if pictures in the pause mode are blurred.
(Refer to page 74.)
Others
Español
EN
45
SPECIAL PLAYBACK
Resume Playback
You can play back from where you stopped playing back
the disc last.
1) During playback, press [STOP C].
The resume message will appear.
Skipping TV Commercials During
Playback
You can skip TV commercials to enjoy the recorded
programs without interrupting.
Resume ON
2) Press [PLAY B].
In a few seconds, playback will resume from the point
at which it stopped last. You can resume playback at
the same point even if you turn off the unit.
To cancel the resume playback and start playing back
the disc from the beginning, press [STOP C] again
while the playback is stopped.
During playback, press [CM SKIP].
Normal playback will start at 30 seconds ahead from the
point you press [CM SKIP].
Every time you press [CM SKIP], the searching point will
be extended by 30 seconds ahead.
You can press [CM SKIP] up to 6 times (180 seconds).
e.g.) Press [CM SKIP] once.
Note
• For MP3/JPEG files, playback will resume from the
beginning of the file at which playback was stopped.
Fast Forward / Fast Reverse Playback
CM Skip 30 sec.
(forwarding 30 seconds)
1) During playback, press [FWD D] or [REV E].
Every time you press [FWD D] or [REV E],
approximate speed will be changed as follows.
Fast forward or fast reverse playback across titles (for
DVD), or files (for MP3 files) is not possible.
40x
20x
5x
normal
speed
playback
2x
20x
40x
B
For audio CD, MP3 files, approximate speed is fixed at
8x with sound.
2) Press [PLAY B] to return to the normal playback.
Note
• Forward/reverse speed will be indicated with icons
as follows.
forward (approx. speed)
2x:
20x:
40x:
reverse (approx. speed)
5x:
20x:
40x:
46
EN
Playback will return to the normal playback.
Rapid Playback
B
B
Press [Bx1.3/0.8] once during playback.
Plays back approximately at 0.8 times of normal
playback.
:
:
Press [Bx1.3/0.8] thrice to play back in
normal speed.
No effects.
2) Press [PLAY B] to resume the normal playback.
pause
1/16x
1/8x
1/3x
To return to the normal playback, press [PLAY B].
Note
• Forward/reverse speed will be indicated with icons
as follows.
forward (approx. speed)
1/16x:
1/8x:
1/3x:
reverse (approx. speed)
1/16x:
1/8x:
1/4x:
Playback
• Audio (language) setting cannot be changed while
using this mode.
• This feature may not work at some point in a disc.
• Audio is PCM during rapid playback mode except
when using digital audio connection.
• When using digital audio connection (COAXIAL), the
LPCM sound (2 channel) will be output.
1/16x
Recording
Note
1/8x
Disc
Management
B:
Press [Bx1.3/0.8] twice during playback.
Plays back approximately at 1.3 times of normal
playback.
1/4x
Basic Setup
1) During playback, press [Bx1.3/0.8].
1) During playback, press [PAUSE F]. Then press
[FWD D] or [REV E].
Every time you press [FWD D] or [REV E],
approximate speed will be changed as follows. (The
sound will remain muted.)
Connections
Rapid playback function is available only during
playback.
This function is available only on discs recorded in the
Dolby Digital format, and plays back in a slightly faster/
slower speed while keeping the sound quality just as
normal playback.
Slow Forward / Slow Reverse Playback
Introduction
SPECIAL PLAYBACK
Step by Step Playback
Editing
1) During playback, press [PAUSE F].
Playback will be paused and sound will be muted.
2) Press [SKIP i ] repeatedly.
Playback will advance one frame at a time when you
press [SKIP i ] with the sound muted.
To play back step by step backward:
Press [SKIP j ] repeatedly.
Every time you press the button, the playback will go
backward by one frame.
• Press and hold [SKIP j ] / [SKIP i ] to reverse/
advance continuously.
3) Press [PLAY B] to resume the normal playback.
Function Setup
Others
Español
EN
47
SPECIAL PLAYBACK
Marker Setting
Zoom
1) During playback, press [DISPLAY].
2) Use [{ / B] to select
, then press [ENTER] within
1 second, or wait for 1 second to display the
selection menu.
e.g.) DVD-video
1/ 5
1/ 5
0:01:00 / 1:23:45
DVD Video
This feature allows you to assign a specific point on a disc
to be called back later.
1) During playback, press [DISPLAY].
2) Use [{ / B] to select
, then press [ENTER] within
1 second, or wait for 1 second to display the marker
list.
e.g.) DVD-video
1/ 5
1/ 5
0:01:00 / 1:23:45
DVD Video
3) Use [K / L] to select a desired zoom factor to zoom,
then press [ENTER].
1/ 5
1/ 5
0:01:00 / 1:23:45
DVD Video
× 1.2
× 1.5
× 2.0
3) Use [K / L] to select a desired marker number.
When it reaches the desired point, press [ENTER].
e.g.) DVD-video
1/ 5
1/ 5
0:01:00 / 1:23:45
DVD Video
Zoom menu will appear.
There are four options
(x1.0, x1.2, x1.5 and x2.0), these are displayed
excluding the current zoom rate.
1
2
3
4
5
6
-------------
Zoom area will be displayed.
The title (track) number and the time will be displayed.
4) Use [K / L / { / B] to select a desired zoom
position, then press [ENTER].
4) To return to the marker:
Use [K / L] to select the desired marker number,
then press [ENTER].
Note
Zoom playback will start.
Note
• When selecting a smaller factor than the current one,
the zoom area will not be displayed.
• To exit the zoom menu, press [DISPLAY] repeatedly.
• To cancel the zoom function, select “x1.0” using
[K / L], then press [ENTER] at step 3.
• You cannot slide the zoomed picture on some JPEG
files.
48
EN
• To clear a marker, select the marker number to be
cleared, then press [CLEAR].
• All markers will be erased when you operate these
operations listed below.
– Opening the disc tray
– Turning off the power
– Record on a recordable disc
• You can mark up to 6 points.
Title/Chapter Search
Introduction
SEARCH
Track Search
1) During playback, press [SKIP i ] to skip the
current title or chapter and move to the next.
The title or chapter will move forward by one at a time.
• If there is no chapter in one title, the current title will
be skipped.
1) During playback, press [SKIP i] to skip the
current track/file and move to the next.
The track/file will move forward one at a time.
To go back to the beginning of the current track/file,
press [SKIP j ].
Press it twice in quick successions to go to the previous
track/file. The track/file will move backward one at a
time.
To go back to the beginning of the current title or
chapter, press [SKIP j ].
Press it twice in quick successions to go to the previous
title or chapter. The title or chapter will move
backward one title at a time.
1) During playback, press [DISPLAY].
2) Use [{ / B] to select
e.g.) DVD-video
1/ 5
1) During playback, press [DISPLAY].
2) Use [{ / B] to select
e.g.) audio CD
1/ 5
, then press [ENTER].
Disc
Management
Using [DISPLAY]
Using [DISPLAY]
, then press [ENTER].
0:00:15 / 0:05:00
CD
1/ 5
0:01:00 / 1:23:45
DVD Video
Recording
e.g.) MP3 files
1/ 5
0:00:15
MP3
The number next to
Basic Setup
Using [SKIP j ] / [SKIP i ]
Connections
Using [SKIP j ] / [SKIP i ]
will be highlighted.
The number next to
will be highlighted.
Playback
3) Use [K / L] or [the Number buttons] to enter a
desired track/file number to search, then press
[ENTER].
After the search, playback will start automatically.
Note
• During CD playback, you can enter a track number
directly using [the Number buttons] for track search
without displaying the menu.
Editing
3) Title:
Use [K / L] or [the Number buttons] to enter a
desired title number to search, then press [ENTER].
Title search will start.
Chapter:
for
Press [B] to move to the number next to
chapter.
Use [K / L] or [the Number buttons] to enter a
desired chapter number to search, then press
[ENTER].
After the search, playback will start automatically.
Note
1/ 5
1/ 5
Function Setup
• In search mode display, total numbers of each search
contents (title/chapter/time) are shown as a
denominator.
0:01:00 / 1:23:45
DVD Video
Others
total number
total time
of titles
of the title
total number
of chapters
Español
EN
49
SEARCH
Time Search
1) During playback, press [DISPLAY].
2) Use [{ / B] to select
e.g.) DVD-video
1/ 5
, then press [ENTER].
1/ 5
0:01:00 / 1:23:45
DVD Video
e.g.) audio CD
1/ 5
0:00:15 / 0:05:00
CD
The number next to
will be highlighted.
To move to the number next to
, press [B].
When time search is not available,
counter are not displayed.
and time
3) Use [K / L / { / B] or [the Number buttons] to
enter a desired time to search, then press [ENTER].
After the search, playback will start automatically.
Note
• Time search is available only in the same track, file or
title.
50
EN
Repeat Playback
Note
2) Use [{ / B] to select
, then press [ENTER] within
1 second, or wait for 1 second to display the
selection menu.
1/ 5
1/ 5
0:01:00 / 1:23:45
• Point B for the repeat A-B playback should be set
within the same chapter or track of point A.
• To cancel the repeat playback, select “OFF” at step 3.
The repeat setting will also be canceled when you
stop playback.
• You cannot select “Group” during the random
playback of MP3/JPEG files.
• Chapter/Track repeat will be canceled whenever
[SKIP G] or [SKIP H] is pressed.
Basic Setup
DVD Video
Random Playback
3) Use [K / L] to select a desired option to repeat,
then press [ENTER].
e.g.) DVD-video
1/ 5
0:01:00 / 1:23:45
DVD Video
OFF
Title
Chapter
A–B
1) Press [SETUP] in stop mode.
0:00:15 / 0:05:00
CD
OFF
Track
All
A–B
1/ 5
e.g.) MP3/JPEG files
1/ 5
0:00:15 / 0:05:00
CD
Recording
2) Use [K / L] to select “CD Playback Mode”, then press
[ENTER].
“CD Playback Mode” menu will appear.
3) Use [K / L] to select “Random Play”, then press
[ENTER].
Random playback will start.
e.g.) audio CD
e.g.) audio CD
1/ 5
You can play back a disc randomly instead of playing
back in the original order.
Disc
Management
1/ 5
Connections
Available repeat function may vary depending the discs.
1) During playback press [DISPLAY], then proceed to
step 2), or press [REPEAT] then proceed to step 3).
Introduction
REPEAT/RANDOM/PROGRAM PLAYBACK/SLIDE SHOW
Random
0:00:15
MP3
Playback
OFF
Track
All
Group
The selected repeat playback will start.
1/ 5
1/ 5
0:01:00 / 1:23:45
DVD
Note
• To cancel random playback, press [STOP C] twice
during random playback. “OFF” appears on the
display menu.
Repeat
Editing
Title
Function Setup
Title:
The current title will be played back repeatedly.
Chapter:
The current chapter will be played back repeatedly.
All:
The current disc will be played back repeatedly.
A-B:
Desired section can be played back repeatedly.
1) Use [K / L] to select “A-B”, then press [ENTER].
2) Press [ENTER] at the desired starting point A.
3) Press [ENTER] at the desired ending point B.
Track:
The current track or file will be played back repeatedly.
Group:
The current folder will be played back repeatedly.
Others
Español
EN
51
REPEAT/RANDOM/PROGRAM PLAYBACK/SLIDE SHOW
Program Playback
Slide Show
You can program the disc to play back in your desired
order.
You can select the display time between 5 seconds and
10 seconds.
1) Press [SETUP] in stop mode.
1) Follow steps 1 and 2 in “Program Playback” on the
left.
2) Use [K / L] to select “CD Playback Mode”, then
press [ENTER].
“CD Playback Mode” menu will appear.
2) Use [K / L] to select “Slide Show”, then press
[ENTER].
3) Use [K / L] to select “Program Play”, then press
[ENTER].
3) Use [K / L] to select the display time, then press
[ENTER].
4) Use [K / L] to select a desired track, then press
[ENTER] or [B].
4) Press [SETUP] to exit.
Note
CD Playback Mode
• Large-size JPEG files take a few moments to be
displayed.
Program Play
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
Total
0:00:00
Repeat this step until you program all the desired
tracks.
5) Press [PLAY B].
CD Playback Mode
Program Play
09
04
10
06
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
Total
-0:31:07
Program playback will start.
Note
• To erase tracks you selected, press [CLEAR] at step 4.
• You can make program settings up to 50 tracks.
• To cancel program playback, press [STOP C] twice
during program playback. “OFF” appears on the TV
screen.
• You may also select a desired track using [the
Number buttons] at step 4.
52
EN
You can select the format of audio and video as you prefer depending on the contents of the disc you are playing back.
Switching Subtitles
Switching Audio Soundtrack
When playing back a DVD-video recorded with 2 or more
soundtracks (these are often in different languages), you
can switch them during playback.
When playing back audio CD, you can switch “L/
R”(stereo), “L”(left) or “R”(right).
Connections
DVD-video may have subtitles in one or more languages.
Available subtitle languages can be found on the disc
case. You can switch subtitle languages anytime during
playback.
Introduction
SELECTING THE FORMAT OF AUDIO AND VIDEO
1) During playback, press [DISPLAY].
1/ 5
1/ 5
3) Use [K / L] to select a desired audio soundtrack or
audio channel, then press [ENTER].
For DVD-video or VR mode DVD-RW
• Audio soundtrack will switch.
e.g.) DVD-video
1/ 5
1/ 5
0:01:00 / 1:23:45
1.Dolby Digital 5.1ch English
2.Dolby Digital 2ch English
OFF
1.English
Subtitle will be displayed in the selected language.
When “OFF” is selected, subtitle will disappear.
• Some discs will only allow you to change the subtitle
from the disc menu. Press [MENU/LIST] or [TOP
MENU] to display the disc menu.
• If a 4-digit language code appears in the subtitle
menu, refer to the “LANGUAGE CODE” on page 85.
1/ 5
0:00:15 / 0:05:00
CD
Playback
Note
• If the title contains both main and sub audio, you can
further select “L“ (main), “R“ (sub), “L/R“ (mixed of
main and sub).
For audio CD
• Audio channel will switch.
Recording
DVD Video
0:01:00 / 1:23:45
DVD Video
Disc
Management
3) Use [K / L] to select a desired subtitle language,
then press [ENTER].
1/ 5
, then press [ENTER] within
2) Use [{ / B] to select
1 second, or wait for 1 second to display the
selection menu.
0:01:00 / 1:23:45
DVD Video
1/ 5
1) During playback press [DISPLAY], then proceed to
step 2), or press [AUDIO] then proceed to step 3).
Basic Setup
2) Use [{ / B] to select
, then press [ENTER] within
1 second, or wait for 1 second to display the
selection menu.
e.g.) DVD-video
1. L/R
2. L
3. R
• Some discs will only allow you to change the
soundtrack from the disc menu. Press [MENU/LIST]
or [TOP MENU] to display the disc menu.
Editing
Note
Function Setup
Others
Español
EN
53
SELECTING THE FORMAT OF AUDIO AND VIDEO
Switching Virtual Surround System
You can enjoy stereophonic virtual space through your
existing 2 channel stereo system.
1) During playback, press [DISPLAY].
2) Use [{ / B] to select
, then press [ENTER] within
1 second, or wait for 1 second to display the
selection menu.
e.g.) DVD-video
1/ 5
1/ 5
Switching Camera Angles
Some DVD-video have scenes shot from 2 or more
angles. Angle information should be on the disc case if
the disc contains multi-angle scenes.
1) During playback, press [DISPLAY].
2) Use [{ / B] to select
1/ 5
, then press [ENTER].
1/ 5
0:01:00 / 1:23:45
DVD Video
0:01:00 / 1:23:45
DVD Video
3) Use [K / L] to select “OFF”, “Type 1” or “Type 2”,
then press [ENTER].
e.g.) DVD-video
1/ 5
1/ 5
0:01:00 / 1:23:45
Angle icon appears when a switching camera angle is
available.
Angle will switch each time you press [ENTER].
DVD Video
OFF
Type 1
Type 2
OFF
: no effect
Type 1 : natural effect
Type 2 : emphasized effect
Note
• Angle icon does not appear on the TV screen if you
set “Angle Icon” to “OFF” in “Playback” menu.
Refer to page 74.
Reducing Block Noise
Note
• Select “OFF” if sound is distorted.
• The setting will be kept when the unit is turned off.
1) During playback, press [DISPLAY].
2) Use [{ / B] to select
, then press [ENTER] within
1 second, or wait for 1 second to display the
selection menu.
e.g.) DVD-video
1/ 5
1/ 5
0:01:00 / 1:23:45
DVD Video
3) Use [K / L] to select a desired option, then press
[ENTER].
1/ 5
1/ 5
0:01:00 / 1:23:45
DVD Video
OFF
Type 1
Type 2
Your setting will be activated.
This function reduces noise in the playback picture. If
noises appear on the TV screen during playing back
discs recorded in long time recording speed such as 6H
or 8H, select “Type 1” or “Type 2”.
(“Type 2” is more effective.)
When playing back discs with a few noises such as
DVD-video, select “OFF”.
54
EN
Guide to a Title List
Editing Discs
Press [TOP MENU].
4
5
6
Title List
JAN/ 1/07 12:00AM L1 LP
12:00PM (2:00:00) JAN/ 1/07
L1 LP
2
3
4
5
6
1/2
2 1
ORG
3
Edit
2
Scene Delete
Edit Title Name
Chapter Mark
Protect
1 : 25 : 47
11 10
9
8
7
ORG
PL
• Once a disc is finalized, editing the disc or recording
to the disc will not be available (except DVD-RW in
VR mode).
• A playlist is not available with the DVD-R and DVDRW in video mode.
Function Setup
Others
Press [RETURN
Note
Editing
Video
Playback
1. Title list: List of the titles recorded on the disc, and
their information.
2. The protect icon, which appears when the title has
been protected. (Original titles only)
3. Arrow: Indicating there is a previous / next page.
4. Title list icon, which indicates a type of the displayed
title list.
: VR(original).
: VR (Playlist).
: Video mode.
5. Title name.
6. Title information, which displays recorded year/ date/
month/ time, length of the title, recorded external
input mode (L1 or L2), and the recording speed.
7. Submenu: Submenus for the selected menu are
displayed here.
8. Title name (editable): If you do not name the title,
the recorded date, time, channel and the recording
speed are displayed here.
9. Progress bar: Indicating the progress of the
playback.
10. Preview window: Preview of the selected title is
displayed here.
11. Playback status: Indicating the current playback
status of the selected title.
Recording
JAN/ 31/07 11:00PM L1 LP
Disc
Management
3
You will find editing discs is easy. This unit offers
convenient edit functions which are possible only with
DVD-RW/-R discs.
You can edit the following from a title list.
• Assigning a name to a title
• Dividing a title
• Combining titles
• Adding titles to a playlist
• Erasing all playlist
• Setting or releasing the title protection
• Adding or deleting chapter marks
• Deleting titles or parts of titles
(Possible editing functions depend on the recording
format and editing method.)
Original and playlist (VR mode)
For VR mode DVD-RW, you can edit the recordings in
playlist without changing the original recordings. Playlist
does not take up much disc space. After you make a
recording to VR mode DVD-RW, a playlist will be created
automatically.
What “Original” or “Playlist” is for?
Throughout this manual, you will find original and playlist
which refer to the actual content and the edited version.
• Original content refers to what’s actually recorded on
the VR mode DVD-RW.
• Playlist content refers to the edited version of the VR
mode DVD-RW; how the original content is to be played
back.
Finalizing a disc
• This will allow a disc that is recorded on this unit to be
played back on other DVD player — without finalization
it will not be playable on other DVD player.
• After finalizing DVD-RW/-R, you cannot edit any
information that is on that disc.
Basic Setup
1
Edit the recorded disc
Connections
Title list allows you to check the titles recorded on the
disc easily. You can choose a title to play back from this
list and easily edit the titles as you prefer.
ORG
Introduction
INFORMATION ON DISC EDITING
] to exit the title list.
Español
EN
55
DELETING TITLES
Notes for deleting titles
After the disc is fully recorded:
DVD-RW
• When the last title is deleted from
DVD-RW in video mode, the recordable
space will be increased.
TITLE 2
TITLE 2
TITLE 3
The deleted title
cannot be created the space.
TITLE 3
TITLE 2
TITLE 2
TITLE 3
TITLE 2
TITLE 2
TITLE 3
You cannot
record
a new title.
Delete!
TITLE 1
You can record
a new title.
TITLE 1
Delete!
TITLE 1
Delete!
TITLE 1
TITLE 1
You can record
a new title.
The Full-Recorded disc
TITLE 1
TITLE 1
Delete!
• When a title is deleted from
DVD-R, the recordable space
will NOT be increased.
The Full-Recorded disc
The Full-Recorded disc
TITLE 2
• When a title is deleted from
DVD-RW in VR mode, the
recordable disc space will
be increased.
DVD-R
You cannot
record
a new title.
Once all editings are made, press [RETURN ] in several times to exit the editing mode. “Writing to Disc” appears
momentarily. It also appears when pressing [OPEN/CLOSE A] or [POWER] before exiting the editing mode after
editing.
56
EN
You can delete titles which you do not need anymore.
Please be advised that the titles once deleted cannot be
brought back to the disc.
Be sure to read “Notes for deleting titles” on page 56
before you delete the title.
ABC
DEF
OPEN/CLOSE
INPUT SELECT
Use [K / L/ s / B] to select a desired
title, then press [ENTER].
e.g.) VR mode DVD-RW original
ORG
Title List
JAN/ 1/07 12:00AM L1 LP
12:00PM (2:00:00) JAN/ 1/07
GHI
JKL
MNO
AUDIO
PQRS
TUV
WXYZ
REPEAT
DISPLAY
SPACE
CLEAR
SETUP
Basic Setup
.@/:
ZOOM
TIMER
PROG.
L1 LP
1
2
3
4
5
6
ENTER
3
REV
PLAY
FWD
ORG
Title List
JAN/ 1/07 12:00AM L1 LP
12:00PM (2:00:00) JAN/ 1/07
1
X1.3/0.8
SKIP
PAUSE
SKIP
STOP
CM SKIP
4
REC/OTR
L1 LP
2
Recording
REC SPEED
Use [K / L] to select “Title Delete”,
then press [ENTER].
Disc
Management
1/2
TOP MENU MENU/LIST RETURN
Connections
POWER
1
2
In stop mode, press [TOP MENU].
Title list, original or playlist will appear.
• For DVD-RW VR mode, press [MENU/LIST] to
switch between “Original” and “Playlist” if the
disc is recorded in VR mode.
Introduction
DELETING TITLES
3
Play From Start
Edit
Title Delete
5
Add To Playlist
6
1/2
NB089
4
Use [K / L] to select “Yes”, then press
[ENTER].
ORG
Playback
DVD RECORDER
Title List
JAN/ 1/07 12:00AM L1 LP
12:00PM (2:00:00) JAN/ 1/07
2
L1 LP
3
Editing
1
Delete this title?
4
Yes
5
No
6
1/2
] or [STOP C] to exit.
Data will be written onto the disc momentarily.
Wait for a moment.
Others
5
Press [RETURN
Function Setup
After that, “Are you sure?” will appear, select
“Yes” and then press [ENTER].
Title will be deleted.
90%
This operation may take
awhile to be completed.
Español
EN
57
CREATING/DELETING PLAYLIST
Adding Titles to a Playlist
Playlist
For VR mode DVD-RW, you can create the playlist as you
wish.
You can add up to 99 titles to a playlist (as long as
the total number of the playlist does not exceed 999
chapters).
POWER
.@/:
GHI
ZOOM
TIMER
PROG.
ABC
DEF
JKL
MNO
OPEN/CLOSE
INPUT SELECT
1
2
3
AUDIO
Follow the step 1 in “DELETING
TITLES” on page 57 to display the
original.
Use [K / L/ s / B] to select the
desired title, then press [ENTER].
Use [K / L] to select “Add To
Playlist”, then press [ENTER].
ORG
Title List
JAN/ 1/07 12:00AM L1 LP
12:00AM (2:00:00) JAN/ 1/07
1
PQRS
TUV
WXYZ
REPEAT
DISPLAY
SPACE
CLEAR
SETUP
RETURN
ENTER
4
TOP MENU MENU/LIST
REV
PLAY
SKIP
FWD
PAUSE
SKIP
STOP
CM SKIP
ORG
Title List
JAN/ 1/07 12:00AM L1 LP
12:00AM (2:00:00) JAN/ 1/07
L1 LP
2
3
Create a Playlist ?
4
REC/OTR
6
Use [K / L] to select “Yes”, then press
[ENTER].
1
X1.3/0.8
3
Play From Start
Edit
Title Delete
5
Add To Playlist
1/2
4
REC SPEED
L1 LP
2
Yes
5
No
6
1/2
The title is added to playlist.
DVD RECORDER
NB089
Note
• To delete a title from the playlist, refer to “DELETING
TITLES” on page 57.
• To delete all titles in the playlist, refer to “Erasing All
Playlist” on page 59.
• When a playlist contains 99 titles or more, or 999
chapters or more, “Add to Playlist” cannot be
selected.
58
EN
5
Press [RETURN
] or [STOP C] to exit.
Writing on the disc starts.
It may take awhile to write the data on a disc.
Introduction
CREATING/DELETING PLAYLIST
Erasing All Playlist
Playlist
POWER
OPEN/CLOSE
.@/:
ABC
DEF
INPUT SELECT
GHI
JKL
MNO
AUDIO
PQRS
TUV
WXYZ
REPEAT
TOP MENU MENU/LIST
CLEAR
SETUP
RETURN
ENTER
REV
PLAY
FWD
X1.3/0.8
SKIP
PAUSE
SKIP
REC/OTR
STOP
CM SKIP
4
DVD Menu
Format
Finalize
Disc Protect OFF ON
Delete All Playlists
Use [K / L] to select “Yes”, then press
[ENTER].
DVD Menu
Format
Finalize
Disc Protect OFF ON
Delete entire playlist?
Delete All Playlist
Recording
REC SPEED
Use [K / L] to select “Delete All
Playlists”, then press [ENTER].
Disc
Management
SPACE
DISPLAY
Use [K / L] to select “DVD Menu”,
then press [ENTER].
Basic Setup
ZOOM
TIMER
PROG.
1
2
3
Press [SETUP].
Main menu will appear.
Connections
A playlist can be deleted if it is no longer needed.
Yes
No
NB089
Playback
DVD RECORDER
“Are you sure?” will appear.
Use [K / L] to select “Yes” and then press
[ENTER]
DVD Menu
Editing
Format
Finalize
Disc Protect OFF ON
Delete
play list?
Areentire
you sure?
Delete All Playlist
Yes
No
Writing on the disc starts.
It may take awhile to write the data on a disc.
Function Setup
Playlist is deleted.
Others
Note
Español
• Deleting a playlist will not increase the available
recording time on the disc.
EN
59
EDITING DISCS
Putting Names on Titles
You can put a name on the disc and change it from this
menu.
POWER
OPEN/CLOSE
ZOOM
TIMER
PROG.
.@/:
ABC
DEF
INPUT SELECT
GHI
JKL
MNO
AUDIO
PQRS
TUV
WXYZ
REPEAT
4
Use [K / L] to select “Edit Title
Name”, then press [ENTER].
ORG
Edit
1
Scene Delete
Edit Title Name
Chapter Mark
Protect
JAN/ 1/07 12:00AM L1 LP
1 : 25 : 47
DISPLAY
SPACE
CLEAR
TOP MENU MENU/LIST RETURN
SETUP
ENTER
5
To enter a title name, follow the
steps of “Guide to Edit Title Name”
on page 61.
ORG
Edit - Edit Title Name
A B C
1
a b c
REC SPEED
REV
PLAY
FWD
X1.3/0.8
SKIP
PAUSE
SKIP
STOP
CM SKIP
character set
1 2 3
@ !
?
M
REC/OTR
1 : 25 : 47
area for entering title names
1
2
When you finish entering a title name, press
[ENTER].
In stop mode, press [TOP MENU].
Title list, original or playlist will appear.
• For DVD-RW VR mode, press [MENU/LIST] to
switch between “Original” and “Playlist” if the
disc is recorded in VR mode.
6
Use [K / L] to select “Yes”, then press
[ENTER].
ORG
Edit - Edit Title Name
Use [K / L/ s / B] to select a desired
title, then press [ENTER].
1
Yes
No
e.g.) VR mode DVD-RW original
ORG
Title List
JAN/ 1/07 12:00AM L1 LP
12:00PM (2:00:00) JAN/ 1/07
1
MY FAVORITE
L1 LP
2
1 : 25 : 47
3
The name you entered will be activated for the title.
4
5
6
1/2
3
Use [K / L] to select “Edit”, then press
[ENTER].
ORG
Title List
JAN/ 1/07 12:00AM L1 LP
12:00PM (2:00:00) JAN/ 1/07
1
4
2
Play From Start
Edit
Title Delete
5
Add To Playlist
L1 LP
3
6
1/2
60
EN
7
Press [RETURN ] and then
[RETURN ] or [STOP C] to exit.
Data will be written onto the disc momentarily.
This operation may take
awhile to be completed.
Introduction
EDITING DISCS
Putting Names on Titles (cont’d)
Guide to Edit Title Name
.@/:
ZOOM
TIMER
PROG.
ABC
DEF
OPEN/CLOSE
INPUT SELECT
Select
Press
JKL
MNO
AUDIO
PQRS
TUV
WXYZ
REPEAT
SPACE
DISPLAY
TOP MENU MENU/LIST
CLEAR
SETUP
RETURN
ENTER
PLAY
FWD
X1.3/0.8
SKIP
PAUSE
SKIP
STOP
CM SKIP
REC/OTR
NB089
<space>
<space>
0
<space>
(*1)
(*1)
1
! ”# $ % & ’( )
*+,-./:;<=>
?@[]^_{|}
ABC
abc
2
(*2)
DEF
def
3
(*2)
GHI
ghi
4
(*2)
JKL
jkl
5
(*2)
MNO
mno
6
(*2)
PQRS
pqrs
7
(*2)
TUV
tuv
8
(*2)
WXYZ
wxyz
9
(*2)
*1 Press
, character set will be changed to the “ @!? ”
mode automatically.
to
, character set will be changed to the
*2 Press
previous input mode automatically.
• To delete letters, press [CLEAR] repeatedly.
Press and hold [CLEAR] to delete all letters.
• Use [s / B] to move the cursor to the left and right.
• You can enter up to 30 letters.
Playback
DVD RECORDER
@!?
Recording
REV
123
Disc
Management
REC SPEED
abc
Basic Setup
GHI
ABC
Connections
POWER
1) Use [K / L] to select a desired character set, then
press [ENTER].
2) Follow the list below, use [the Number buttons]
repeatedly until the desired letter appears.
Editing
Function Setup
Others
Note
Español
• Undefined letters in a title name are shown by “*”. If
you delete them, adjoining letters may change to “*”
or other.
EN
61
EDITING DISCS
Setting or Clearing Chapter Marks
Original
Playlist
You can put chapter marks in each title. Once a chapter is
marked, you can use it for the chapter search feature.
POWER
OPEN/CLOSE
ZOOM
TIMER
PROG.
.@/:
ABC
DEF
INPUT SELECT
GHI
JKL
MNO
AUDIO
PQRS
TUV
WXYZ
REPEAT
DISPLAY
SPACE
CLEAR
SETUP
RETURN
ENTER
TOP MENU MENU/LIST
1
2
3
Follow steps 1 to 3 in “Putting Names
on Titles” on page 60 to display “Edit”
menu.
4
Use [K / L] to select “Add” or
“Delete”, then press [ENTER].
Use [K / L] to select “Chapter Mark”,
then press [ENTER].
Submenu will appear.
Use [SKIP H / G],
[REV E], [FWD D], [PLAY B] and
[PAUSE F] to find the point where
you will create a new chapter mark.
Or, use [SKIP H / G] to find a
chapter mark that you wish to delete.
e.g.) VR mode DVD-RW original
ORG
Edit - Chapter Mark
1
REC SPEED
REV
PLAY
FWD
X1.3/0.8
SKIP
PAUSE
SKIP
STOP
CM SKIP
REC/OTR
Chapter
Add
Delete
2/3
JAN/ 1/07 12:00AM L1 LP
1 : 25 : 47
DVD RECORDER
NB089
5
Use [K / L] to select “Yes”, then press
[ENTER].
If you select “Add” at step 4, a new chapter mark
will be added, and if you select “Delete” at step
4, the chapter mark will be deleted.
e.g.) Add
ORG
Edit - Chapter Mark - Add
1
Chapter
Yes
No
2/3
JAN/ 1/07 12:00AM L1 LP
1 : 25 : 47
A new chapter mark will be added.
Note
• The maximum number of chapter for VR mode DVDRW is 999 chapters per entire original and playlist.
• Besides the above-mentioned, it is not likely to be
able to add according to recorded time and number
of chapters.
62
EN
6
7
Press [RETURN
].
Press [RETURN ] again and then
[RETURN ] or [STOP C] to exit.
Data will be written onto the disc momentarily.
This operation may take
awhile to be completed.
Introduction
EDITING DISCS
Deleting a Part of a Title
Original
Playlist
3
Use [SKIP H / G],
[REV E], [FWD D], [PLAY B] and
[PAUSE F] to find the start point,
then press [ENTER].
PL
POWER
Edit - Scene Delete
OPEN/CLOSE
TIMER
PROG.
.@/:
ABC
DEF
INPUT SELECT
GHI
JKL
MNO
AUDIO
PQRS
TUV
WXYZ
REPEAT
DISPLAY
SPACE
CLEAR
SETUP
RETURN
ENTER
1
Start
End
Preview
Delete
Basic Setup
ZOOM
Connections
You can delete a specific part of a title.
Even when parts of title are deleted from the playlist, the
original title will remain as it is.
JAN/ 1/07 12:00AM L1 LP
1 : 00 : 00
PL
Edit - Scene Delete
1
REV
PLAY
FWD
X1.3/0.8
SKIP
PAUSE
SKIP
STOP
CM SKIP
Start
End
Preview
Delete
Recording
REC SPEED
Disc
Management
TOP MENU MENU/LIST
Then use [SKIP H / G],
[REV E], [FWD D], [PLAY B] and
[PAUSE F] again to move to the end
point, and press [ENTER].
JAN/ 1/07 12:00AM L1 LP
1 : 15 : 00
REC/OTR
DVD RECORDER
NB089
Editing
start point end point
Before
editing
Function Setup
1
2
Follow the steps 1 to 3 in “Putting
Names on Titles” on page 60 to
display the “Edit” menu.
Playback
The cursor will move to “Preview”.
The bar at the bottom of the screen indicates the
total and the elapsed time of the title, and the
area selected for deletion is indicated in red.
You can check the preview by pressing [ENTER].
• Before and after 5 seconds of the deleted point
will be playback for preview.
Edited
Use [K / L] to select “Scene Delete”,
then press [ENTER].
e.g.) VR mode DVD-RW playlist.
Edit
1
Others
PL
Scene Delete
Edit Title Name
Chapter Mark
Title Dividing
Title Combining
JAN/ 1/07 12:00AM L1 LP
Instructions continue on the next page.
EN
63
Español
1 : 25 : 47
EDITING DISCS
Deleting a Part of a Title (cont’d)
4
Use [K / L] to select “Delete” then
press [ENTER].
PL
Edit - Scene Delete
1
Start
End
Preview
Delete
JAN/ 1/07 12:00AM L1 LP
1 : 40 : 00
5
Use [K / L] to select “Yes” then press
[ENTER].
“Are you sure?” will appear. Select “Yes” using
[K / L] and then press [ENTER].
PL
Edit - Scene Delete
1
Are you sure?
Yes
No
JAN/ 1/07 12:00AM L1 LP
1 : 40 : 03
The part of the title is deleted.
6
Press [RETURN ] and then
[RETURN ] or [STOP C] to exit.
Data will be written onto the disc momentarily.
This operation may take
awhile to be completed.
Note
• When a scene is deleted from an original, the scene
on the playlist will also be deleted.
• You cannot select “Scene Delete” if the number of
chapter marks in the original or playlist is more than
999.
• The recordable disc space will not increase even after
deleting a part of a title on the playlist.
64
EN
Introduction
EDITING DISCS
Dividing a Title
Playlist
POWER
OPEN/CLOSE
TIMER
PROG.
.@/:
ABC
DEF
INPUT SELECT
GHI
JKL
MNO
AUDIO
PQRS
TUV
WXYZ
REPEAT
Use [K / L/ s / B] to select a desired
title, then press [ENTER].
Use [K / L] to select “Edit”, then press
[ENTER].
e.g.) VR mode DVD-RW playlist
PL
Title List
JAN/ 1/07 12:00AM L1 LP
12:00PM (2:00:00) JAN/ 1/07
SPACE
DISPLAY
CLEAR
TOP MENU MENU/LIST RETURN
SETUP
REV
PLAY
FWD
X1.3/0.8
SKIP
PAUSE
SKIP
STOP
CM SKIP
5
6
Use [SKIP H], [SKIP G], [REV E],
[FWD D], [PAUSE F] and [PLAY B]
to decide the point at which you will
divide the title.
Use [K / L] to select “Title Dividing”,
then press [ENTER].
Use [K / L] to select “Yes”, then press
[ENTER].
PL
Edit - Title Dividing
DVD RECORDER
1
Playback
4
5
6
3
Play From Start
Edit
Title Delete
Recording
REC SPEED
REC/OTR
4
ENTER
L1 LP
2
Disc
Management
1
Basic Setup
ZOOM
1
2
3
Connections
You can divide one title into 2 new titles.
In stop mode, press [TOP MENU].
• For VR mode DVD-RW, press [MENU/LIST] to
select “Playlist”.
Yes
No
NB089
Editing
JAN/ 1/07 12:00AM L1 LP
1 : 25 : 47
The title will be divided into 2 new titles.
Both title names are identical.
] or [STOP C] to exit.
Data will be written onto the disc momentarily.
Writing to Disc
90%
Others
This operation may take
awhile to be completed.
Function Setup
7
Press [RETURN
Note
Español
• You cannot divide a title of the disc when the
number of recording titles reaches the maximum of
99, and the number of recording chapters reaches
the maximum of 999.
EN
65
EDITING DISCS
Combining Titles
Playlist
You can combine 2 titles into a single title.
POWER
OPEN/CLOSE
ZOOM
TIMER
PROG.
.@/:
ABC
DEF
INPUT SELECT
GHI
JKL
MNO
AUDIO
PQRS
TUV
WXYZ
REPEAT
DISPLAY
SPACE
CLEAR
SETUP
RETURN
ENTER
1
2
Follow the steps 1 to 3 in “Dividing a
Title” on page 65 to display “Edit”
menu.
Use [K / L] to select “Title
Combining”, then press [ENTER].
PL
Edit
1
Scene Delete
Edit Title Name
Chapter Mark
Title Dividing
Title Combining
JAN/ 1/07 12:00AM L1 LP
1 : 25 : 47
TOP MENU MENU/LIST
Title combining setting window will appear.
Selected title grays out, and the frame of the
next title becomes yellow.
PL
Edit - Title Combining
JAN/31/07 11:00PM L1 LP
11:00PM (0:30:00) JAN/31/07
L1 LP
1
2
3
4
5
6
1+
REC SPEED
REV
PLAY
FWD
X1.3/0.8
SKIP
PAUSE
SKIP
STOP
CM SKIP
1/2
REC/OTR
DVD RECORDER
NB089
3
4
Use [K / L / { / B] to select another
title to combine, then press [ENTER].
Use [K / L] to select “Yes”, then press
[ENTER].
PL
Edit - Title Combining
JAN/31/07 11:00PM L1 LP
11:00PM (0:30:00) JAN/31/07
1
L1 LP
2
3
1 + 2 Combine selected titles?
Yes
No
4
5
6
1/2
The 2 titles will combine into a single title.
PL
Title List
JAN/ 1/07 12:00AM L1 LP
12:00PM (2:30:00) JAN/ 1/07
L1 LP
1
2
3
4
5
6
1/2
Note
• You cannot select the same title twice and combine
it into a single title.
• If either one of the 2 original titles is deleted, the
combined new title is also deleted.
66
EN
5
Press [RETURN
] or [STOP C] to exit.
Data will be written onto the disc momentarily.
This operation may take
awhile to be completed.
Introduction
EDITING DISCS
Setting or Releasing the Title Protection
Original
ORG
1
.@/:
ABC
DEF
INPUT SELECT
GHI
JKL
MNO
AUDIO
PQRS
TUV
WXYZ
REPEAT
DISPLAY
SPACE
CLEAR
SETUP
RETURN
ENTER
JAN/ 1/07 12:00AM L1 LP
1 : 25 : 47
• If the title is protected,
original list.
• If the title is already protected, “ON OFF” will
appear. If you press [ENTER], the title will be
released from protection.
PLAY
FWD
X1.3/0.8
SKIP
PAUSE
SKIP
STOP
CM SKIP
Edit - Protect
1
OFF
ON
Playback
REV
JAN/ 1/07 12:00AM L1 LP
1 : 25 : 47
•
DVD RECORDER
4
will appear on the title in the original list.
Press [RETURN ] and then [RETURN
] or [STOP C] to exit.
Data will be written onto the disc momentarily.
Editing
NB089
Recording
3
will appear in the
Confirm the indication
“OFF ON”. Press [ENTER] again.
ORG
REC SPEED
Scene Delete
Edit Title Name
Chapter Mark
Protect
Disc
Management
ZOOM
REC/OTR
Edit
OPEN/CLOSE
TIMER
PROG.
TOP MENU MENU/LIST
Use [K / L] to select “Protect”, then
press [ENTER].
Basic Setup
POWER
1
2
Connections
To prevent the accidental editing, or erasing of the titles,
you can protect them in “Edit” menu.
You can cancel the title protection feature after it is
applied.
Follow the steps 1 to 3 in “Putting
Names on Titles” on page 60 to
display “Edit” menu.
This operation may take
awhile to be completed.
Select “Disc Protect OFF ON” from the DVD
Menu, then select “Yes”.
Refer to “SETTING A DISC TO PROTECT” on page
26.
Function Setup
To protect a whole disc
(VR mode DVD-RW only):
Others
Español
EN
67
EDITING DISCS
Setting or Clearing All Chapter Marks at Once
For titles in video mode DVD-RW, you can set or edit
chapter at every time interval. You can clear the chapter
mark too.
You can specify the interval of chapter marks for titles last
more than 5 minutes.
1
2
Follow the steps 1 to 3 in “Putting
Names on Titles” on page 60 to
display “Edit” menu.
Use [K / L] to select “Chapter Mark”,
then press [ENTER].
Video
Edit
1
POWER
OPEN/CLOSE
ZOOM
TIMER
PROG.
.@/:
ABC
DEF
INPUT SELECT
GHI
JKL
MNO
AUDIO
PQRS
TUV
WXYZ
REPEAT
DISPLAY
SPACE
CLEAR
SETUP
RETURN
ENTER
Edit Title Name
Chapter Mark
JAN/ 1/07 12:00AM L1 LP
TOP MENU MENU/LIST
1 : 25 : 47
3
Use [K / L] to select the desired
interval, then press [ENTER].
Video
Edit - Chapter Mark
1
OFF
5 minutes
10 minutes
15 minutes
30 minutes
60 minutes
JAN/ 1/07 12:00AM L1 LP
REC SPEED
REV
PLAY
FWD
X1.3/0.8
SKIP
PAUSE
SKIP
STOP
CM SKIP
REC/OTR
DVD RECORDER
NB089
Note
• You cannot select a chapter mark interval that
exceeds the length of a title.
• The length of chapters may slightly deviate from the
one specified at the step 3.
• A chapter mark may be delayed depending on the
recording content.
• The maximum number of chapter for video mode
DVD is 99 chapters per disc and title.
68
EN
1 : 25 : 47
4
5
Use [K / L] to select “Yes”, then press
[ENTER].
Chapter marks are added.
If you select “OFF” at step 3, all the chapter
marks are erased.
Press [RETURN ] and then [RETURN
] or [STOP C] to exit.
Data will be written onto the disc momentarily.
This operation may take
awhile to be completed.
Introduction
LIST OF SETTINGS
The following table is the contents which you can set and the default settings.
Refer to the following table for useful operation.
Setup
Playback
Audio Out
→ page 73
Dynamic Range
Control
ON
OFF
Compressing the range of sound volume.
PCM
48kHz
96kHz
PCM
Stream
English
French
Spanish
Other
Set whether the sound recorded in 96kHz will be
down sampled in 48kHz.
Original
English
French
Spanish
Other
OFF
English
French
Spanish
Other
Set the language for audio.
Angle Icon
→ page 74
ON
OFF
Set whether to display the angle icon or not.
Still Mode
→ page 74
Auto
Field
Frame
Set the type of still image in pausing playback.
OSD Language
→ page 76
English
Français
Español
OFF
5minutes
10minutes
15minutes
30miniutes
Auto
Bright
Dark
Set the language for OSD (on-screen display).
Dolby Digital
Disc Menu Language
→ page 73
Subtitle Language
→ page 74
FL Dimmer
→ page 76
Set the idling time before the screen saver starts.
Playback
Screen Saver
→ page 76
Set the language for subtitles.
Recording
Display
Set the type of sound signal which outputs from the
digital audio output jack.
Set the language for disc menu language.
Disc
Management
General Setting
Audio Language
→ page 73
Contents
Set the parental level for DVD playback.
Basic Setup
All
level 8 to 1
Connections
Items (highlight is the default)
Parental Lock
→ page 72
Set the brightness of the front panel display.
Editing
Function Setup
Others
Español
EN
69
LIST OF SETTINGS
Setup
Video
Items (highlight is the default)
Progressive
→ page 78
TV Aspect
→ page 78
Select Video L1(Rear)
→ page 16
General Setting
L2(Front)
Recording
Auto Chapter
→ page 25
Auto
Finalize
→ page 27
Disc Full
End of Timer Rec
Aspect Ratio(Video mode)
→ page 25
Clock
Reset All
→ page 79
Clock Setting → page 22
ON
OFF
4:3 Letter Box
4:3 Pan & Scan
16:9 Wide
Video In
S-Video In
Video In
S-Video In
OFF
5 minutes
10 minutes
15 minutes
30 minutes
60 minutes
ON
OFF
ON
OFF
Auto
4:3
16:9
Yes
No
Contents
Set to the progressive scan mode (set to "ON") or to
the interlace scan mode(set to "OFF").
Set a picture size according to aspect ratio of your TV.
Set the video input type for the external input.
Insert chapter marks at even time interval.
Set the unit to finalize the disc automatically.
Set a aspect ratio for video mode recording.
Set the clock.
Set to the default setting.
Note
• Your change to each settings stays on even when the power is off.
• An item which is not currently available is grayed in the settings.
• “Make Recording Compatible“ in “Recording“ menu does not work on this unit.
70
EN
Introduction
SETUPS
Playback
Press [STOP C] if you are playing back a disc.
OPEN/CLOSE
.@/:
ABC
DEF
INPUT SELECT
GHI
JKL
MNO
AUDIO
TUV
WXYZ
REPEAT
DISPLAY
SPACE
CLEAR
SETUP
RETURN
ENTER
TOP MENU MENU/LIST
REV
PLAY
FWD
X1.3/0.8
SKIP
PAUSE
SKIP
STOP
CM SKIP
REC/OTR
3
General Setting
Playback
Display
Video
Recording
Clock
Reset All
1
2
3
4
5
6
7
Recording
REC SPEED
Use [K / L] to select a desired item,
then press [ENTER].
Use [K / L] to select “Playback”, then
press [ENTER].
Disc
Management
PQRS
1
2
Basic Setup
ZOOM
TIMER
PROG.
Connections
POWER
Press [SETUP] and use [K / L] to
select “General Setting“, then press
[ENTER].
Parental Lock
Audio Out
Disc Menu Language
Audio Language
Subtitle Language
Angle Icon
Still Mode
Submenu will appear.
NB089
When you finish with the setting,
press [SETUP] to exit.
Editing
4
5
Refer 1 to 7 on pages 72 to 74 and
set the selected item.
Playback
DVD RECORDER
Function Setup
Others
Español
EN
71
SETUPS
Playback (cont’d)
1
Parental Lock (Default: All)
Some DVD-video feature a parental lock level. Playback
will stop if the ratings exceed the levels you set, it will
require you to enter a password before the disc will
playback. This feature prevents your children from
viewing inappropriate material.
Use [K / L] to select the desired level, then press
[ENTER].
A
Use [K / L] to select “Yes”, then press [ENTER]. Use
[the Number buttons] to enter a new password except
for 4737, then press [ENTER].
General Setting
Playback
Display
Video
Recording
Clock
Reset All
General Setting
Playback
Display
Video
Recording
Clock
Reset All
Parental Lock
All
8
7
6
5
4
3
2
1
Parental Lock
Audio Out
Disc Menu Language
Audio Language
Subtitle Language
Angle Icon
Still Mode
If a password has not been set yet, proceed to A .
If a password has been set already, proceed to B .
A password has not been set yet.
General Setting
Parental Lock
Parental Lock
All
Audio Out
8
Change
Password?
Disc Menu Language
7
Audio Language
Yes
6
Subtitle Language
No
5
Angle Icon
4
Still Mode
3
2
1
Playback
Display
Video
Recording
Clock
Reset All
Yes
Parental Lock
Parental Lock
All
Audio Out
8
Disc Menu Language
7
Password
Input
Audio
Language
6
Subtitle Language
5
Angle Icon
4
Still Mode
3
2
1
Your setting will be activated.
B
A password has been set already.
• Use [the Number buttons] to enter the current
password.
General Setting
Note
• Parental lock function may not be available to some
discs.
• With some DVD, it may be difficult to find if they are
compatible with parental lock. Be sure to check if the
parental lock function operates in the way that you
have set.
• Record the password in case you forget it.
• If there is a DVD in the unit when you set up the
parental lock, press [OPEN/CLOSE A] to activate the
parental lock level.
Playback
Display
Video
Recording
Clock
Reset All
Parental Lock
Parental Lock
All
Audio Out
8
Disc Menu Language
7
Password
Input
Audio
Language
6
Subtitle Language
5
Angle Icon
4
Still
Mode
3
2
1
Your setting will be activated.
• If you want to change password, use [K / L] to select
“Yes” then press [ENTER]. Use [the Number buttons]
to enter a new password, then press [ENTER].
<change the password>
General Setting
Playback
Display
Video
Recording
Clock
Reset All
General Setting
Parental Lock
Parental Lock
All
Audio Out
8
Change
Password?
Disc Menu Language
7
Audio Language
Yes
6
Subtitle Language
No
5
Angle Icon
4
Still Mode
3
2
1
Playback
Display
Video
Recording
Clock
Reset All
Yes
Parental Lock
Parental Lock
All
Audio Out
8
Disc Menu Language
7
Password
Input
Audio
Language
6
Subtitle Language
5
Angle Icon
4
Still Mode
3
2
1
Your setting will be activated.
Note
• Press [CLEAR] to erase numbers entered incorrectly.
• When you forget the password or you want to clear
all settings in “Parental Lock” menu, enter 4,7,3,7
using [the Number buttons] in password input
window. Password will be cleared and parental levels
will be set to “All”.
72
EN
Introduction
SETUPS
Playback (cont’d)
2
C
Audio Out
Use [K / L] to select a setting, then press [ENTER].
General Setting
Use [K / L] to select a desired item, then press [ENTER].
Playback
Display
Video
Recording
Clock
Reset All
General Setting
A
A
B
C
Parental Lock
Audio Out Audio Out
Disc Menu Language
Dynamic Range
AudioControl
Language
PCM
Subtitle Language
Dolby Digital
Angle Icon
Still Mode
Dynamic Range Control (Default : ON)
General Setting
Playback
Display
Video
Recording
Clock
Reset All
3
Disc Menu Language (Default : English)
Set the language for disc menu.
Use [K / L] to select a language, then press [ENTER].
Recording
Parental Lock
Audio Out Audio Out
Menu
Language
Dynamic Disc
Range
Control
Dynamic Range
AudioControl
Language
PCM ON Subtitle Language
DolbyOFF
Digital
Angle Icon
Still Mode
Your setting will be activated.
PCM
: Converts the Dolby Digital into PCM (2 channel).
When your amplifier/decoder is NOT
compatible with Dolby Digital, set to “PCM”.
Stream : Outputs Dolby Digital signals
When your amplifier/decoder is compatible
with Dolby Digital, set to “Stream”.
General Setting
Playback
Display
Video
Recording
Clock
Reset All
Your setting will be activated.
Note
B
PCM (Default : 48kHz)
Use [K / L] to select a setting, then press [ENTER].
Parental Lock
Out
Disc Menu Audio
Language
Disc Menu Language
EnglishAudio Language
FrenchSubtitle Language
Spanish
Angle Icon
Other Still Mode
Playback
• Dynamic range control function is available only on
the discs which are recorded in the Dolby Digital
format.
Your setting will be activated.
4
Disc
Management
Set to “ON” to compress the range between soft and loud sounds.
Use [K / L] to select a setting, then press [ENTER].
Parental Lock
Audio Out Audio Out
Disc Menu Language
Dolby Digital
Dynamic Range
AudioControl
Language
PCM PCMSubtitle Language
DolbyStream
Digital
Angle Icon
Still Mode
Basic Setup
Playback
Display
Video
Recording
Clock
Reset All
Connections
Choose the appropriate audio setting for your external device.
It will only affect a disc playback.
Dolby Digital (Default : Stream)
Audio Language (Default : Original)
Set the audio language.
Use [K / L] to select a language, then press [ENTER].
General Setting
Parental Lock
Audio Out Audio Out
Disc Menu Language
PCM
Dynamic Range
AudioControl
Language
PCM 48kHz
Subtitle Language
Dolby96kHz
Digital
Angle Icon
Still Mode
Parental Lock
Audio Out
Audio Language
Disc Menu Language
Original
Audio Language
EnglishSubtitle Language
FrenchAngle Icon
Spanish
Still Mode
Other
Your setting will be activated.
• When “Original” is selected, the audio language will be
in the disc’s default language.
Function Setup
Your setting will be activated.
48kHz : If your amplifier/decoder is NOT compatible
with 96kHz PCM, select “48kHz”. 96kHz sound
will be output in 48kHz.
96kHz : If your amplifier/decoder is compatible with
96kHz PCM, select “96kHz”. 96kHz sound will
be output.
Playback
Display
Video
Recording
Clock
Reset All
Editing
General Setting
Playback
Display
Video
Recording
Clock
Reset All
Others
Note
When playing back disc with copyright protection
• Even if you select “96kHz”, the sound will be down
sampled at 48kHz.
Español
EN
73
SETUPS
Playback (cont’d)
5
Subtitle Language (Default : OFF)
Set the subtitle language.
Use [K / L] to select a language, then press [ENTER].
6
Angle Icon (Default : ON)
Set to “ON” to show the angle icon during the playback.
Use [K / L] to select a setting, then press [ENTER].
General Setting
General Setting
Playback
Display
Video
Recording
Clock
Reset All
Playback
Display
Video
Recording
Clock
Reset All
Parental Lock
Audio Out
Subtitle Language
Disc Menu Language
OFF Audio Language
EnglishSubtitle Language
FrenchAngle Icon
Spanish
Still Mode
Other
Your setting will be activated.
Your setting will be activated.
If “Other” is selected for 3 to
using [the Number buttons].
5 , press 4-digit code
Code Input
-
-
Parental Lock
Audio Out
Angle IconDisc Menu Language
Audio Language
ON Subtitle Language
OFF Angle Icon
Still Mode
-
7
Still Mode (Default : Auto)
Select “Auto” usually.
Use [K / L] to select a setting, then press [ENTER].
General Setting
• When you finish entering the code, press [ENTER].
Refer to the language code table on page 85.
Playback
Display
Video
Recording
Clock
Reset All
Note
• Only the languages supported by the disc can be
selected.
• Audio language setting may not be available to
some discs.
• You can change or switch off the subtitles on a DVD
also from the disc menu if it is available.
• Press [CLEAR] to erase numbers entered incorrectly.
Parental Lock
Still Mode Audio Out
Disc Menu Language
Auto Audio Language
Field Subtitle Language
Frame Angle Icon
Still Mode
Your setting will be activated.
Auto
: Optimum resolution setting (“Field” or
“Frame”) will be selected.
Field
: Images in the still mode will be stabilized.
Frame : Images in the still mode will be highly defined.
Note
• Frame is one completed video image made up of 2
fields (There are 30 frames per second of NTSC
video).
74
EN
Introduction
SETUPS
Display
Press [STOP C] if you are playing back a disc.
OPEN/CLOSE
.@/:
ABC
DEF
INPUT SELECT
GHI
JKL
MNO
AUDIO
PQRS
TUV
WXYZ
REPEAT
DISPLAY
SPACE
CLEAR
SETUP
RETURN
ENTER
TOP MENU MENU/LIST
1
2
3
Use [K / L] to select “Display”, then
press [ENTER].
Use [K / L] to select a desired item,
then press [ENTER].
1 OSD Language
2 Screen Saver
3 FL Dimmer
Disc
Management
TIMER
PROG.
Selection menu will appear.
REV
PLAY
FWD
X1.3/0.8
SKIP
PAUSE
SKIP
STOP
CM SKIP
REC/OTR
4
5
Refer to 1 to 3 on page 76 and set
the selected item.
When you finish with setting, press
[SETUP] to exit.
Recording
REC SPEED
Basic Setup
ZOOM
Connections
POWER
Press [SETUP] and use [K / L] to
select “General Setting”, then press
[ENTER].
Playback
DVD RECORDER
NB089
Editing
Function Setup
Others
Español
EN
75
SETUPS
Display (cont’d)
1
OSD Language (Default : English)
Set the language for the on-screen display.
Use [K / L] to select a setting, then press [ENTER].
General Setting
Playback
Display
Video
Recording
Clock
Reset All
OSD Language
Screen Saver
OSD Language
FL Dimmer
English
Français
Español
Your setting will be activated.
2
Screen Saver (Default : 10 minutes)
Set the time to activate the screen saver function on the
TV screen.
Use [K / L] to select a setting, then press [ENTER].
General Setting
Playback
Display
Video
Recording
Clock
Reset All
OSD Language
Screen Saver
Screen Saver
FL Dimmer
OFF
5 minutes
10 minutes
15 minutes
30 minutes
Your setting will be activated.
3
FL Dimmer (Default: Bright)
Set the front panel display brightness.
Use [K / L] to select a setting, then press [ENTER].
General Setting
Playback
Display
Video
Recording
Clock
Reset All
OSD Language
FL DimmerScreen Saver
FL Dimmer
Auto
Bright
Dark
You can choose one from “Auto”, “Bright” or “Dark”.
If “Auto” is selected, the display gets dark when the
power is off.
76
EN
Introduction
SETUPS
Video
Press [STOP C] if you are playing back a disc.
OPEN/CLOSE
.@/:
ABC
DEF
INPUT SELECT
GHI
JKL
MNO
AUDIO
PQRS
TUV
WXYZ
REPEAT
DISPLAY
SPACE
CLEAR
SETUP
RETURN
ENTER
TOP MENU MENU/LIST
Use [K / L] to select “Video”, then
press [ENTER].
Use [K / L] to select a desired item,
then press [ENTER].
1 Progressive
2 TV Aspect
3 Select Video
Submenu will appear.
REV
PLAY
FWD
X1.3/0.8
SKIP
PAUSE
SKIP
STOP
CM SKIP
REC/OTR
Device“ on page 39.
When you finish with the setting,
press [SETUP] to exit.
Playback
4
5
Recording
REC SPEED
Refer 1 to 2 on page 78 and set the
selected item.
• For 3 , refer to “Connection to an External
Disc
Management
TIMER
PROG.
Basic Setup
ZOOM
1
2
3
Connections
POWER
Press [SETUP] and use [K / L] to
select “General Setting”, then press
[ENTER].
DVD RECORDER
NB089
Editing
Function Setup
Others
Español
EN
77
SETUPS
Video (cont’d)
1
2
Progressive (Default : OFF)
This unit is compatible with the progressive scan system.
The feature provides you with the higher definition
images than the traditional output system does. To utilize
this feature, you must set progressive scan mode to “ON”.
1) Use [K / L] to select “ON“, then press [ENTER].
General Setting
Playback
Display
Video
Recording
Clock
Reset All
General Setting
General Setting
Playback
Activating progressive scan:
Display
Progressive
Check your TV has progressive
scan
Video
TV Aspect
Progressive
and connect with
component
video cable.
Rcording
Select Video
ON
Clock
OFF
Reset
All:
NOTE
If there is no picture or picture is
distorted after selecting “Yes”,
Wait about 15 seconds for auto recovery.
Yes
No
3) Use [K / L] to select “Yes“ within 15 seconds, then
press [ENTER].
Your setting will be activated.
Note
• If your TV is compatible with progressive scan (525p /
480p), you are recommended to use the component
video cable (commercially available) to connect this
unit to the TV. (Refer to “Method 3” on page 17.) If
not, use the RCA video cable and set the progressive
scan to “OFF” or press and hold [SETUP] for more
than 3 seconds during DVD playback.
• When selecting “No” or not pressing any buttons on
the unit or remote control within 15 seconds at step
3, progressive scan remains to be “OFF” (interlace
scan).
78
EN
You can select the TV aspect ratio to match the formats of
what you are playing back with the unit and your TV
screen (4:3 standard or 16:9 widescreen TV).
Use [K / L] to select a desired option, then press
[ENTER].
Playback
Display
Video
Recording
Clock
Reset All
Progressive
TV Aspect
Progressive
Video Input
ON
OFF
2) Use [{ / B] to select “Yes“, then press [ENTER].
Activate?
TV Aspect (Default: 4:3 Letter Box)
Progressive
TV Aspect TV Aspect
Select Video
4:3 Letter Box
4:3 Pan & Scan
16:9 Wide
If you have a standard TV:
Select “4:3 Letter Box”, so that black bars appear on the
top and bottom of the TV screen when playing back a
wide-screen picture. Select “4:3 Pan & Scan” for a full
height picture with both sides trimmed when playing
back wide-screen picture.
If you have a widescreen TV:
Select “16:9 Wide”.
Introduction
SETUPS
Reset All
Reset the setting to default.
OPEN/CLOSE
ABC
DEF
INPUT SELECT
GHI
JKL
MNO
AUDIO
PQRS
TUV
WXYZ
REPEAT
DISPLAY
SPACE
CLEAR
SETUP
RETURN
ENTER
TOP MENU MENU/LIST
REV
PLAY
FWD
X1.3/0.8
SKIP
PAUSE
SKIP
STOP
CM SKIP
REC/OTR
NB089
4
Reset to factory default?
Yes
No
Select “Yes” again using [K / L] ,
then press [ENTER].
Playback
DVD RECORDER
General Setting
Playback
Display
Video
Recording
Clock
Reset All
Recording
REC SPEED
3
Select “Yes” using [K / L] , then press
[ENTER].
General Setting
Playback
Display
Video
Recording
Clock
Reset All
General Setting
Playback
Display
Video
Recording
Clock
Reset All
Disc
Management
.@/:
Use [K / L] to select “Reset All”, then
press [ENTER].
Basic Setup
ZOOM
TIMER
PROG.
Connections
POWER
1
2
Press [SETUP] in stop mode and use
[K / L] to select “General Setting”,
then press [ENTER].
ResetAre
to factory
defauit?
you sure?
Editing
Yes
No
Your setting in recording will be initialized.
Function Setup
Others
Note
Español
• The settings listed below will remain unchanged
even after resetting to the factory default.
- Clock setting
- Channel setting
- OSD language setting
- Parental lock setting
- Timer programs
EN
79
TROUBLESHOOTING
Before requesting service for this unit, check the table below for a possible cause of the problem you are experiencing.
Some simple checks or a minor adjustment on your part may eliminate the problem and restore proper operation.
Symptom
Power
The power does not turn on.
Picture
There is no picture.
Remedy
• Check that the AC power cord is connected securely.
• Check the breaker (in case of power failure).
• Re-connect the connecting cords securely.
• Check if the connecting cords are damaged.
• If the main menu appears on the TV screen, press [RETURN ] to exit.
• Check the connection to your TV (page 17).
• Check if the progressive scan mode is set correctly according to your TV
(page 78).
• Switch the input selector on your TV (such as to “L1”) so that the signal from
the unit appears on the TV screen.
Picture noise appears.
• Clean the disc with a cleaning cloth.
TV program pictures are
distorted.
• Check if all the connections are made correctly.
Playback picture is distorted.
• Keep the device which may cause electrical disturbances, such as a cellular
phone away.
Cannot record a TV program.
• This unit does not have a tuner to receive TV broadcasting.
• You must connect this unit to an external tuner to record TV programs (page
15).
Sound
There is no sound.
• Clean the disc with a cleaning cloth.
• Re-connect all connections securely.
• Check if the connecting cord is damaged.
• Check the connections to the amplifier input.
• Check if the input device setting on the amplifier is correct.
• When the unit is in pause mode or in slow-motion playback mode, sound is
not output. This is not a malfunction.
• When the unit is in fast forward or fast reverse mode, sound is not output.
This is not a malfunction.
• If you are using COAXIAL DIGITAL AUDIO OUTPUT jack, check the setting in
“Audio Out” (page 73).
No DTS sound is output.
• This unit is not compatible with DTS sound.
Sound is noisy.
• Clean the disc with a cleaning cloth.
Remote control
The remote control does not
function.
80
EN
• Batteries are weak.
• There are obstacles between the remote control and the unit.
• The remote control is far from the unit.
• There are no batteries in the remote control.
• Check if the unit is turned on.
• Check if you are pointing the remote control at the recorder and NOT the TV.
If you have a plasma TV, it may interfere with the IR signal. Try the remote
with the plasma off. If the remote works, you may need to move the unit
away from the plasma TV.
Symptom
Playback
The disc does not play back.
Remedy
Connections
• No disc is inserted.
• A blank disc is inserted.
• The disc is upside down. Insert the disc with the labeled side facing up.
• The disc is not correctly inserted.
• The unit cannot play back certain discs (such as a CD-ROM) (page 9).
• The region code on the DVD-video does not match the unit (page 9).
• Moisture has condensed inside the unit. Remove the disc and leave the unit
turned on for about 2 hours until the moisture evaporates (page 4).
• If the disc was recorded on another recorder, the unit cannot play back the
disc if it was not finalized.
Introduction
TROUBLESHOOTING
Basic Setup
The unit starts playing back the
disc automatically.
• The DVD-video features an auto playback function.
Some functions such as stop,
search, or slow-motion playback
cannot be performed.
• Depending on the disc, you may not be able to do some of the operations.
Refer to the instruction manual supplied with the disc.
The language for the sound track
cannot be changed.
• The title does not have the multilingual audio tracks.
• The DVD-video prohibits the changing of the language for the sound track.
The subtitle language cannot be
changed or turned off.
• Multilingual subtitle are not recorded on the DVD-video.
The angles cannot be changed.
• Multi-angles are not recorded on the DVD-video being played back.
• The angle-change operation is whenever possible as long as the disc contains
a multi-angle portion. Actual change will be performed when the portion has
come up.
• The DVD-video prohibits changing angles.
• Try changing the angle using the DVD-video’s menu.
Playback
Recording / Timer recording / Editing
Nothing was recorded even
• There was a power failure during recording.
though you set the timer setting
• The unit’s internal clock stopped due to a power failure that lasted for more
correctly.
than 30 seconds. Reset the clock (page 22).
• The program contains copy protection signals that restricts copying.
• The timer setting overlapped with another setting that has priority.
Recording
• Resume playback was activated (page 46). Press [STOP C] twice.
• You have inserted a disc whose title menu or DVD menu automatically
appears on the TV screen when it is first inserted.
Disc
Management
The disc does not start playback
from the beginning.
• It will take a few seconds for the unit to input disc data before recording
stops.
Timer recording is not complete
or did not start from the
beginning.
• The timer setting overlapped with another setting that has priority (page 36).
• Disc space was not enough.
Editing
Recording does not stop
immediately after you press
[STOP C].
Function Setup
Others
Español
EN
81
TROUBLESHOOTING
Symptom
Others
The unit does not operate
properly.
Remedy
• When static electricity, etc., causes the unit to operate abnormally, unplug
the unit and then plug it in again.
The disc tray does not open when
you press [OPEN/CLOSE A].
• It may take a few seconds for the disc tray to open after you have recorded or
edited a disc. This is because the unit is adding disc data to the disc.
“Repairing” appears on the TV
screen.
• If there is a power failure or unplugging during recording, finalizing,
formatting or editing (even after “Repairing” disappears), a repairing process
will begin automatically just after turning the unit on again.
It may take several minutes up to about several hours.
Repairing
In a case you intend to cancel the
repairing process.
Do you want to cancel a repairing process ?
When selecting “Yes”, the disc may not be
usable.
Yes
No
Repairing
82
EN
• If you intend to cancel the repairing process, press [OPEN/CLOSE A]
on the front panel, then select “Yes” and press [ENTER]. After that, press
[OPEN/CLOSE A] to take out the disc. The disc canceled during the
repairing process MAY NOT work.
Error message
• You cannot record copy prohibited
programs.
• Set “Format Mode” to “VR mode” (page
23).
• You are trying to record on to the protected
disc which is set in “DVD Menu” menu.
• You are trying to record onto the disc
which has no space for recording.
• Release the disc protect setting in “DVD
Menu” menu (page 26).
• Insert the recordable disc with enough
recording space.
• You are trying to record onto the DVDRW/-R on which the number of recording
titles comes up to the maximum (99).
• You are trying to record onto the VR mode
DVD-RW on which the number of recording
chapters comes up to the maximum (999).
• This disc has no space to write the Control
Information when recording or deleting contents.
When editing has been repeatedly performed,
the control Information area may come up to be
full even the recording area has enough space.
• When recordings are performed
repeatedly onto an unstable disc, this
area may come up to be full.
• Every time you insert a disc for recording,
the disc’s working area will be taken up.
And if you repeat this frequently, it will
be used up sooner and you may not be
able to record full 99 titles.
• You are trying to record onto the disc
already finalized.
• Delete unnecessary titles (page 57).
• Insert the recordable disc, and ensure
the disc status satisfies the recording
requirements (page 8).
• Clean the disc with a cleaning cloth.
• Replace the disc.
• Insert the DVD-RW disc in VR mode
(ver.1.1 or 1.2 compatible with CPRM).
• Delete unnecessary chapter marks
(page 62).
• Delete unnecessary titles (page 57).
Playback
• Insert a new disc.
• Undo the finalizing for this disc (pages
28-29).
Editing
Recording Error
This disc is already finalized.
• You are trying to record the copy
prohibited program.
• You are trying to record the copy-once
program onto the DVD-RW disc in video
mode.
• You are trying to record onto the disc
which is unrecordable, or the disc status
is unable to record.
• The disc is dirty.
• The disc is damaged.
• You are trying to record the copy-once
program onto the DVD-RW disc which
is not compatible with CPRM.
Recording
Recording Error
You cannot record on this disc as Power
Calibration Area is full.
• Check “Parental Lock” setting in
“Playback” menu (page 72).
Disc
Management
Recording Error
This disc is protected and not recordable.
Recording Error
Disc is full.
(No area for new recording)
Recording Error
You cannot record more than 99 titles on one disc.
(The maximum is 99)
Recording Error
You cannot record more than 999 chapters on one disc.
(The maximum is 999)
Recording Error
You cannot record on this disc as Control
Information is full.
• Playback is not authorized in the region
of the DVD-video which you inserted in
the unit.
• The current selected parental level
prohibits playback.
Solution
• Insert the standardized disc which have
the marks on pages 8-9.
• Insert the disc with the labeled side facing up.
• Insert the DVD-video with region codes
1 or ALL.
Basic Setup
Recording Error
This program is not allowed to be
recorded on this disc.
Cause
• Unplayable disc is inserted in the unit.
• The disc is upside down.
Connections
Disc Error
— Please eject the disc. —
Playback feature may not be available on this disc.
Region Error
— Please eject the disc. —
Playback is not authorized in your region.
Parental Lock On
The current selected parental level
prohibits playback.
Recording Error
This program is not allowed to be recorded.
Recording Error
This program is not recordable in Video
mode.
Recording Error
Cannot record on this disc.
Introduction
TROUBLESHOOTING
* If you are still having trouble with the unit after checking “TROUBLESHOOTING”, write down the error code and the
error description for calling our help line to locate an Authorized Service Center.
Function Setup
Others
Español
EN
83
TROUBLESHOOTING
Frequently Asked Questions
– Can I record to CD-RW/-R?
No, this unit records only DVD.
– Can I play back DVD-video that is bought in another
country?
Possible when the region code of the disc is 1 and All.
– Can I connect the unit to my PC?
No, you cannot control the unit by PC.
– Can I program a timer recording with an external
tuner?
Yes, you can. Select “L1” or “L2” as your recording
channel, and leave the external tuner on (pages 15, 3336).
– Can I record one channel while watching another
channel using an external tuner?
It depends on your connection configurations. For more
details, please kindly contact at your local store.
– Can I change the channels on the external tuner using
the remote control of this unit?
No. Changing the channels on the external tuner using
this unit’s remote control is not possible. You need to use
the remote control supplied with the external tuner to
change the channels on the external tuner.
84
EN
Editing
Function Setup
Code
6467
6559
6553
6547
5350
6564
6554
6566
6660
6560
6550
6555
6565
6557
6558
6561
5165
6567
6569
6568
6658
6653
6647
6666
6651
6654
4861
6655
6661
6665
6664
6657
6669
6757
6764
6772
6855
6861
4971
6961
7054
5655
7161
7267
Playback
Language
Russian
Samoan
Sangho
Sanskrit
Scots Gaelic
Serbian
Serbo-Croatian
Sesotho
Setswana
Shona
Sindhi
Singhalese
Siswat
Slovak
Slovenian
Somali
Spanish
Sundanese
Swahili
Swedish
Tagalog
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga
Tsonga
Turkish
Turkmen
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
Recording
Others
Code
5467
5565
5560
5547
5551
5557
5347
5566
5647
5669
5760
5765
5757
6469
5771
6460
5761
5767
5861
5847
5868
5860
5866
5957
5953
5965
5958
5966
5955
5964
5961
5960
6047
6051
6061
6149
6164
6159
6247
6265
5247
6258
6266
6367
6459
6461
Disc
Management
Language
Hungarian
Icelandic
Indonesian
Interlingua
Interlingue
Inupiak
Irish
Italian
Japanese
Javanese
Kannada
Kashmiri
Kazakh
Kinyarwanda
Kirghiz
Kirundi
Korean
Kurdish
Laothian
Latin
Latvian; Lettish
Lingala
Lithuanian
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
Marathi
Moldavian
Mongolian
Nauru
Nepali
Norwegian
Occitan
Oriya
Oromo (Afan)
Panjabi
Pashto; Pushto
Persian
Polish
Portuguese
Quechua
Rhaeto-Romance
Romanian
Basic Setup
Code
4748
4747
4752
6563
4759
4764
5471
4765
4771
4772
4847
5167
4860
5072
4854
4855
4864
4853
5971
4851
5759
4947
7254
4961
5464
4965
5047
6058
5160
5161
5166
5261
5256
5255
5264
5271
5358
5747
5051
5158
5758
5360
5367
5447
5569
5455
Connections
Language
Abkhazian
Afar
Afrikaans
Albanian
Amharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali;Bangla
Bhutani
Bihari
Bislama
Breton
Bulgarian
Burmese
Byelorussian
Cambodian
Catalan
Chinese
Corsican
Croatian
Czech
Danish
Dutch
English
Esperanto
Estonian
Faroese
Fiji
Finnish
French
Frisian
Galician
Georgian
German
Greek
Greenlandic
Guarani
Gujarati
Hausa
Hebrew
Hindi
Introduction
LANGUAGE CODE
Español
EN
85
GLOSSARY
Analog Audio
PCM (pulse code modulation)
An electrical signal that directly represents sound.
Compare this to digital audio which can be an electrical
signal, but is an indirect representation of sound. See also
“Digital Audio”.
The most common system of encoding digital audio,
found on CD and DAT. Excellent quality, but requires a
lot of data compared to formats such as Dolby Digital
and MPEG audio. For compatibility with digital audio
recorders (CD, MD and DAT) and AV amplifiers with
digital inputs, this unit can convert Dolby Digital and
MPEG audio to PCM. See also “Digital Audio”.
Aspect Ratio
The width of a TV screen relative to its height.
Conventional TVs are 4:3 (in other words, the TV screen
is almost square); widescreen models are 16:9 (the TV
screen is almost twice as wide as it is high).
Chapter
Just as a book is split up into several chapters, a title on a
DVD is usually divided into chapters. See also “Title”.
Component Video Output
Progressive Scan (525p/480p)
A type of display that does not split each frame into
fields, and instead scans directly through all the scanlines
of each frame in order. Progressive scan provides less
flickering and higher image resolution than traditional
(525i/480i) TV signals. Refer to page 78 for instructions on
selective progressive scan mode.
Each signal of luminance (Y) and component (PB/CB, PR/
CR) is independent to output so that you can experience
picture color as it is.
Also, due to compatibility with progressive video
(525p/480p), you can experience higher-density picture
than that in interlace (525i/480i).
Region Code
Digital Audio
Sampling Frequency
An indirect representation of sound by numbers. During
recording, the sound is measured at discrete intervals
(44,100 times a second for CD audio) by an analogto-digital converter, generating a stream of numbers.
On playback, a digital-to-analog converter generates
an analog signal based on these numbers. See also
“Sampling Frequency” and “Analog Audio”.
Dolby Digital
The system to compress digital sound developed by
Dolby Laboratories. It offers you sound of stereo(2ch) or
multi channel audio.
Regions associate discs and players with particular areas
of the world. This unit will only play back discs that have
compatible region codes. You can find the region code
of your unit by looking on the rear panel. Some discs are
compatible with more than one region (or all regions).
The rate which sound is measured by a specified interval
to turn into digital audio data. The numbers of sampling
in one second defines as sampling frequency. The higher
the rate, the better the sound quality.
S-Video Output
It delivers independently each signal of color(C) and
luminance(Y) to TV as video signals, so that higher-quality
picture will be gained.
Title (DVD only)
A collection of chapters on DVD. See also “Chapter”.
Finalize
Track
To make DVD, which have been recorded on, possible to
play back in DVD players.
Audio CD use tracks to divide up the content of a
disc. The DVD equivalent is called a chapter. See also
“Chapter”.
JPEG (joint photographic experts group)
JPEG is a method of compressing still image files. You can
copy JPEG files on CD-RW/-R from a computer and play
back the files on this unit.
MP3 (MPEG audio layer 3)
MP3 is a method of compressing files. You can copy MP3
files on CD-RW/-R from the computer and play back the
files on this unit.
86
EN
Introduction
SPECIFICATIONS
• This model complies with the below specifications.
• Designs and specifications are subject to change without notice.
• This model may not be compatible with features and/or specifications that may be added in the future.
13.5 MHz
MPEG
48 kHz
Dolby Digital
Recording
Front
VR (video recording) format, video format
DVD-Rewritable, DVD-Recordable
Disc
Management
2V rms (input impedance: more than 22kΩ)
1Vp-p (75Ω)
Y: 1Vp-p (75Ω)
C: 286mVp-p (75Ω)
2V rms (input impedance: more than 22kΩ)
Playback
2V rms (output impedance: more than 1kΩ)
1Vp-p (75Ω)
1Vp-p (75Ω)
C: 286mVp-p (75Ω)
Y: 1Vp-p (75Ω)
C: 286mVp-p (75Ω)
Y: 1Vp-p (75Ω)
PB/CB: 700mVp-p (75Ω)
PR/CR: 700mVp-p (75Ω)
500mVp-p (75Ω)
Function Setup
Y: 1Vp-p (75Ω)
Editing
Rear
DVD-RW/-R, DVD-video, CD-DA, CD-RW/-R
120V AC +/-10%, 60Hz +/-5%
18W (standby: 2.8W)
16.6 x 2.4 x 9.8 inches (420 x 59 x 247mm)
4.7 lbs. ( 2.1kg )
41°F (5°C) to 104°F (40°C)
Less than 80% (no condensation)
Basic Setup
Audio recording format
Sampling frequency
Compression format
Terminals
Audio input
RCA jack x 2
Video input
RCA jack x 1
S-video input
Mini DIN 4-pin x 1
Audio input
RCA jack x 2
Audio output
RCA jack x 2
Video input
RCA jack x 1
Video output
RCA jack x 1
S-video input
Mini DIN 4-pin x 1
S-video output
Mini DIN 4-pin x 1
Component video output
RCA jack x 3
Coaxial digital audio output
RCA jack x 1
Connections
General
System
Power requirements
Power consumption
Dimensions (width x height x depth)
Weight
Operating temperature
Operating humidity
Recording
Recording format
Recording discs
Video recording format
Sampling frequency
Compression format
Others
Español
EN
87
ESPAÑOL
Discos grabables y reproducibles
Tipo de disco
DVD-RW
DVD-R
Logotipo
Formato
Puede formatearse en modo VR o modo de
video
Modo de video
480 minutos
Tiempo máximo de (12 centímetros)
grabación 144 minutos
(8 centímetros)
Modo VR
480 minutos
(12 centímetros)
144 minutos
(8 centímetros)
480 minutos
(12 centímetros)
144 minutos
(8 centímetros)
Versione 2.0
Versione 2.0/4×
Versione 2.0/8×
Versione 2.0/16×
Versione 1.1,1.2
Versiones grabables/
Versione 1.1/2× CPRM compatible
reproducibles
Versione 1.2/4× CPRM compatible
Se puede reproducir
en la mayoría de los
reproductores de
Compatibilidad
DVD. Es necesario
finalizar. (se creará el
menú de DVD)
Formateado
automáticamente en modo de video
Se puede reproducir
sólo en unidades
compatibles con
el modo VR. Se
recomienda finalizar.
Se puede reproducir en la mayoría de los
reproductores de DVD. Es necesario finalizar.
(se creará el menú de DVD)
Discos reproducibles
Tipo de disco
DVD-VIDEO
CD-DA
CD-RW
CD-R
Logotipo
Archivos reproducibles
Título de disco
Medio
MP3
JPEG
CD-RW/-R
CD-RW/-R
Los reproductores de DVD con
pueden reproducir DVD-RW grabados en modo VR.
• Los siguientes discos se recomiendan para obtener una
buena calidad de grabación y han sido comprobados
como compatibles con este aparato. Sin embargo, según
sea la condición del medio el equipo podría no leer el
disco correctamente.
Verbatim
DVD-R 8x,
DVD-RW 2x
JVC
DVD-RW 4x
Maxell
DVD-R 8x/16x
El comportamiento de cualquier otro disco no está
garantizado.
Códigos de Región
El número presente en el interior
el globo se refiere a una región
del mundo.Este aparato puede
reproducir discos DVD que estén
rotulados para ALL las regiones o
para la región 1.
88
ES
es una marca registrada de
DVD Format/Logo Licensing Corporation.
Discos no Reproducibles
En este aparato no se podrán reproducir los siguientes
discos.
• CD-ROM
• Disco compacto interactivo (CD-I)
• Disco simple de video (VSD)
• DVD-ROM
• Audio en DVD
• Disco sin finalizar
• El DVD contiene archivos MP3 o JPEG
• DVD-R grabado en formato VR o en formato de
grabación no compatible
En el siguiente disco, es posible que no se escuche el
sonido.
• Super audio CD - Sólo se podrá escuchar el sonido de la
capa del CD. No se podrá escuchar el sonido de la capa
de alta densidad de un super audio CD.
Introduction
ESPAÑOL
Conexión a un Sintonizador Externo
1) Desconecte el cable de alimentación de su televisor del tomacorriente de CA.
2) Efectúe la conexión como se ilustra abajo.
Connections
parte trasera de su televisor
ej.)
cable coaxial de RF
VIDEO IN
señal de TV
AUDIO IN
R
L
ANT. IN
VIDEO
OUT
S-VIDEO
OUT
VIDEO VIDEO
IN
OUT
cable de video
RCA
OUT
L
L
Y
Disc
Management
IN
cable de audio
RCA
cable de S-video
AUDIO OUT
R
L
Basic Setup
cable de video
RCA
cable coaxial
de RF
PB/CB
o
cable de
audio RCA
R
AUDIO IN
(L1)
R
IN
S-VIDEO AUDIO OUT
PR/CR
COMPONENT
VIDEO OUT
OUT
S-VIDEO
VIDEO VIDEO
IN
OUT
sintonizador externo
L
L
Y
PB/CB
R
AUDIO IN
(L1)
IN
R
S-VIDEO AUDIO OUT
PR/CR
COMPONENT
VIDEO OUT
OUT
COAXIAL
S-VIDEO
DIGITAL AUDIO OUTPUT
PCM / BITSTREAM
Recording
parte trasera de este aparato
3) Enchufe los cables de alimentación de los aparatos al tomacorriente de CA.
Selección de un Canal de Entrada Externo en el Televisor
Playback
Luego de completar las conexiones, cambie el selector de entrada del televisor a un canal de entrada externo
adecuado. Presione un botón que seleccione un canal externo de entrada en el control remoto original del
televisor hasta que aparezca la imagen inicial del grabador de DVD. Para obtener detalles consulte el manual
del propietario de su televisor.
Configuración de la Entrada de Video
Antes de efectuar una grabación se debe informar al aparato qué conector hembra de entrada de video se está utilizando.
5
Utilice [K / L] para seleccionar el tipo
de conector hembra de entrada a
conectar, y luego presione [ENTER].
Editing
Ajuste general
Utilice [K / L] para seleccionar
“Video”, y luego presione [ENTER].
Reproduc.
Pantalla
Video
Grabación
Reloj
Rest. todo
Escaneo progresivo
Aspecto de TV
L1Entrada
(Tras.) Entrada
de videode video
Function Setup
de Video
E1Entr.
(Tras.)
Video-S
E2Entr.
(Front.)
Utilice [K / L] para seleccionar
“Selecc. Video”, y luego presione
[ENTER].
Utilice [K / L] para seleccionar la
posición de la entrada externa
deseada, y luego presione [ENTER].
6
Para salir presione [SETUP].
Others
1
2
3
4
Presione [SETUP] y utilice [K / L]
para seleccionar “Ajuste general”, y
luego presione [ENTER].
Ajuste general
Escaneo progresivo
Aspecto de TV
Entrada de video
Selecc. Video
Español
Reproduc.
Pantalla
Video
Grabación
Reloj
Rest. todo
L1 (Tras.)
L2 (Front.)
ES
89
ESPAÑOL
Configuración Inicial
Cuando usted encienda este aparato por primera vez
necesita seguir estos pasos.
1
2
Presione [POWER].
Encienda el televisor. Seleccione la entrada a
la cual está conectado el aparato.
Utilice [K / L] para seleccionar su
idioma deseado, y luego presione
[ENTER] para establecerlo.
Initial Setting
Grabación Básica
1
Presione [OPEN/CLOSE A] para abrir la
bandeja de discos e insertar su disco
con el rótulo aupntando hacia arriba.
2
Para seleccionar la velocidad de
grabación presione [REC SPEED].
* Este aparato puede grabar a DVD-RW y
DVD-R. El disco DVD-R pueden ser grabados
sólo una vez. El disco DVD-RW pueden ser
grabados y borrados muchas veces.
SP
2:00
OSD Language
Modo de
grabación
English
Français
Español
XP / 1H
SP / 2H
LP / 4H
EP / 6H
SLP / 8H
3
Presione [ENTER] para activar “Ajste
Manual de Reloj”.
Ajuste inicial
3
Presione [INPUT SELECT] para
seleccionar la posición adecuada de
la entrada externa (L1/L2) a la cual
está conectado su sintonizador
externo. Luego seleccione en el
sintonizador externo el canal que
desea grabar.
4
Presione [REC/OTR] para iniciar la
grabación.
Ajste Manual de Reloj
--- / -- / ---- (---)
-- : -- --
4
Utilice [{ / B] para seleccionar un
elemento a configurar, y utilice [K / L]
para seleccionar el contenido de su
preferencia, y luego presione [ENTER].
Ajuste inicial
Ajste Manual de Reloj
ENE / 01 / 2007 ( LUN )
12 : 00 AM
Calidad del video
Tiempo de
y el sonido
grabación
Disco de 8 cm Disco de 12 cm
18 min
60 min
Buena
36 min
120 min
72 min
240 min
108 min
360 min
Deficiente
144 min
480 min
Para configurar la grabación a un toque con
temporizador (OTR)...
Esta es una manera sencilla de configurar el tiempo de
grabación en bloques de 30 minutos.
Presione [REC/OTR] repetidamente hasta que aparezca en
la pantalla del televisor la longitud deseada de grabación
(30 minutos a 8 horas).
Comenzará la grabación a un toque con temporizador.
I
0:30
0:30
(grabación normal)
8:00
1:00
7:30
• Para cambiar la duración de la grabación durante la
grabación a un toque con temporizador, presione [REC/OTR]
repetidamente hasta que aparezca la duración deseada.
• Para cancelar la grabación a un toque con temporizador
dentro del tiempo especificado, presione [STOP C].
5
90
ES
Para de tener la grabación presione
[STOP C].
Introduction
ESPAÑOL
Grabación con Temporizador
.@/:
TIMER
PROG.
ABC
DEF
INPUT SELECT
1
JKL
MNO
AUDIO
PQRS
TUV
WXYZ
REPEAT
SPACE
CLEAR
SETUP
RETURN
ENTER
DISPLAY
LUN ENE/01 11:00AM
Fcha
3
4
5
Empieza Termina
Prog. nuevo
L1/L2
Configure una programación del
temporizador.
Presione [ENTER].
Presione [POWER] para configurar
una programación del temporizador.
Aparecerá
en el pantalla del panel frontal.
Configure la fecha.
y
2
TOP MENU MENU/LIST
Fcha
ENE/02
L1/L2
L1
2
Empieza
--:-Vel.
2H
Termina
--:--
2H
2 : 00
Playback
4
Configure las horas de inicio y finalización.
REV
PLAY
FWD
X1.3/0.8
SKIP
PAUSE
SKIP
STOP
CM SKIP
Fcha
ENE/02
L1/L2
L1
Empieza
12 : 00AM
Vel.
2H
Termina
--:--
2H
REC/OTR
2 : 00
Seleccione la posición adecuada de la entrada
externa (L1/L2) a la cual está conectado su
sintonizador externo.
Fcha
ENE/02
L1/L2
L1
Editing
REC SPEED
Termina
1 : 00AM
Empieza
12 : 00AM
Vel.
2H
2H
1 : 00
Function Setup
DVD RECORDER
Seleccione la velocidad de grabación.
NB089
Fcha
ENE/02
L1/L2
L1
Recording
GHI
Programaci. con Reloj
Disc
Management
5
OPEN/CLOSE
ZOOM
Utilice [K / L] para seleccionar “Prog.
nuevo”, y luego presione [ENTER].
Basic Setup
POWER
1
2
Presione [TIMER PROG.].
Connections
Usted puede programar el equipo para que grabe hasta 12
programas, con un mes de anticipación. También hay
disponibles grabaciones de programas diarias o semanales.
Antes de grabar, asegúrese de que
• Cuando llegue el momento en que desea empezar a
grabar, conecte el sintonizador externo a ya sea L1 o L2 y
configúrelo para dar salida a las señales de audio/video.
• No cambie el canal del sintonizador externo cuando esté
grabando. Usted no puede mirar un canal y grabar otro
al mismo tiempo.
• Antes de establecer una programación del temporizador
configure el reloj.
• Inserte un disco grabable con suficiente espacio libre.
Termina
1 : 00AM
Empieza
12 : 00AM
Vel.
2H
2H
1 : 00
Reproducción
OPEN/CLOSE
2
Inserte un disco.
3
Comience a
reproducir.
PLAY
4
Detenga la
reproducción.
Others
1
Abra la bandeja
de discos.
STOP
Español
ES
91
LIMITED WARRANTY
FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship
as follows:
DURATION:
PARTS: FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the date
of original retail purchase. Certain parts are excluded from this warranty.
LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of
original retail purchase.
LIMITS AND EXCLUSIONS:
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE RECEIPT OR OTHER
PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH THE PRODUCT TO OBTAIN SERVICE
UNDER THIS WARRANTY.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing
or if service was attempted by an unauthorized service center. This limited warranty does not apply to any
product not purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occur during normal use. It
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or products
not supplied by FUNAI CORP., or damage, which results from accident, misuse, abuse, mishandling,
misapplication, alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or
office use of this product, or damage which results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE CONTROL), ANY
COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY GENERAL, INDIRECT
OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE INABILITY TO USE THIS
PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL
OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS
REPRESENTATIVES IN THE UNITED STATES.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY AN AUTHORIZED SERVICE CENTER.
THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED-IN TO AN AUTHORIZED SERVICE CENTER.
THE PRODUCT MUST BE ACCOMPANIED BY A COPY OF THE ORIGINAL RETAIL PURCHASE RECEIPT. IF NO PROOF
OF PURCHASE IS ATTACHED, THE WARRANTY WILL NOT BE HONORED AND REPAIR COSTS WILL BE CHARGED.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VARY FROM
STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO OBTAIN SATISFACTION
WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITHOUT
PRIOR NOTICE.
WARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRS:
To obtain warranty service, you must take the product, or deliver the product freight prepaid, in either its original
packaging or packaging affording an equal degree of protection, to any AUTHORIZED SERVICE CENTER. FUNAI
CORP. will not reimburse you for any service done by unauthorized service providers without prior written
approval.
To locate your nearest AUTHORIZED SERVICE CENTER or for general service inquiries, please
contact us at:
FUNAI CORPORATION
Customer Service
Tel: 1-800-968-3429
http://www.SylvaniaConsumerElectronics.com
19900 Van Ness Avenue, Torrance, CA 90501
Printed in China
E7E2AUD
1VMN23368 ★★★★★
Download PDF
Similar pages