Extron DVI 201/201 A D Tx/Rx DVI/HDMI Extender Series

Add to my manuals
3 Pages

advertisement

Extron DVI 201/201 A D Tx/Rx DVI/HDMI Extender Series | Manualzz

Specifications

DVI 201, DVI 201 A D Series

NOTE: *Appropriate DVI-D to HDMI cables or adapters are required for HDMI signal input/output.

Also, an optional Extron HDMI-to-DVI adapter is required in order to transmit a CEC signal.

Video

Maximum data rate ........................ 4.95 Gbps (1.65 Gbps per color)

Maximum pixel clock ...................... 165 MHz

Resolution range ............................ 1920x1200 or 1080p @ 60 Hz

Formats ......................................... RGB and YCbCr digital video

Standards ...................................... DVI 1.0, HDMI

Video input and loop through — transmitters

Number/signal type ........................ 1 single link DVI-D (or HDMI*) input

1 single link DVI-D (or HDMI*) local loop-through

Connectors

DVI 201 Tx .............................. 2 female DVI-D

DVI 201 A D Tx ........................ 1 female DVI-I

Interconnection between transmitter and receiver

Connectors .................................... 2 female RJ-45 per unit for 2 cables connecting the transmitter and receiver

Termination standards .................... TIA/EIA T568A or T568B

Signal transmission distance

1920x1200 or 1080p @ 60 Hz

Extron STP201 cable ......... Up to 150' (45 m)

CAT 5/5e/6 STP ................ Up to 125' (38 m)

CAT 5/5e/6 UTP ................ Up to 100' (30 m)

1024x768 or 720p/1080i @ 60 Hz

CAT 5/5e/6 UTP or STP or Extron STP201 Up to 200' (60 m)

NOTE: The transmission distance varies greatly depending on the signal resolution and on the type of cable, graphics card, and display used in the system.

NOTE: Shielded twisted pair cable provides added protection from outside interference and increases overall signal transmission distance. Extron strongly recommends using shielded twisted pair for optimal performance.

Video output — receivers

Number/signal type ........................ 1 single link DVI-D (or HDMI*)

Connectors

DVI 201 Rx .............................. 2 female DVI-I

DVI 201 A D Rx ....................... 2 female DVI-I

Audio — DVI 201 A D Tx/Rx

Gain ............................................... Unbalanced output: 0 dB; balanced output: +6 dB

Frequency response ...................... 20 Hz to 20 kHz, ±0.05 dB

THD + Noise .................................. 0.10% @ 1 kHz at nominal level

S/N ................................................ >85 dB at maximum output (unweighted)

Stereo channel separation .............. >86 dB @ 1 kHz

Extron DVI 201/201 A D Tx/Rx DVI/HDMI Extender Series Transmitters/Receivers • Specifications 1

THIS TEXT WINDOW and its contents are for reference only. Delete this material before finishing and releasing the specs sheet.

z z

For manuals (guides), use the standard Section style from the current user guide template instead of Chapter title, specs sheet or Heading 1, specs stand-alone; use Heading 1 as usual for “Specifications” if the specs are part of a multitopic chapter.

z z Click the text tool where you want to insert the specs table, select the specs table

container paragraph style, then paste in the specs table from the stand-alone master specs sheet.

z z

For specifications from template v7.6 or earlier, use this guide to which new paragraph style replaces which old style: z z z z z z z z

Specs8_Heading 2 replaces SpecsSubHdr

Specs8_L1 “ Specs7

Specs8_L1 cont’d

Specs8_L2

Specs7A

Specs7 subcategory z z z z

Specs8_L3

Specs8_Note

“ Specs7 sub-subcategory

“ SpecsNote7 z z z z

Specs8_Warning/Caution “

Specs8_ Revision code “

Specs7Warning/caution

Revision code z z

The other new styles are required for proper table placement/formatting (one for the entire specs table as placed within a manual section [specs table conteiner], two others

[ Specs8_Note L1 table and Specs8_Note L2 table] for the note/caution cells within the specs table). z z

At this time, the notes, cautions, and warnings boxes/tables within specs have to be hand inserted and merged and formatted. Use the existing table styles ( NOTE,

Caution, and Warning1) for the table boxes.

z z z z z z

Apply the Specs8_Note L1 table or Specs8_Note L2 table paragraph style

(depending on the content to which the note, caution, or warning applies) to the nested note, caution, or warning table. Also apply the Specs8_Note cell insets cell style to the cell containing the note, caution, or warning nested table.

Apply the Specs8_Note or Specs8_Warning/Caution paragraph style to the text within the nested note, caution, or warning table.

Apply the Specs8_note cell inset cell style to the specs table cell containing the nested table.

For use with user guides (manuals) only (but NOT for stand-alone specs sheets), two bulleted note styles are available to use when you combine a series of notes into one note table: z z

Specs8_Note_bulleted — This is for the first paragaph, and you have to manually insert the bullet character and second tab.

z z

Specs8_Note_bulleted, cont'd — This is for susequent paragaphs within a note box. The bullet character is automatically inserted.

Here is an example of how those two styles are used:

NOTES: • This is just test text to show the style. You wouldn't normally put completely unrelated topics together in a shared note.

All nominal levels are at ±10%. UL rated for use in plenum airspaces: meets UL 2043 for heat and smoke release, excluding the power supply; meets UL 60950 for safety.

UL rated for use in plenum airspaces: meets UL 2043 for heat and smoke release, excluding the power supply; meets UL 60950 for safety.

Specifications are subject to change without notice. UL rated for use in plenum airspaces: meets UL 2043 for heat and smoke release, excluding the power supply; meets UL 60950 for safety.

The 5-pole port supports both hardware and software flow control.

The 3-pole ports support software flow control.

Audio input — DVI 201 A D Tx/Rx

Number/signal type

DVI 201 A D Tx ........................ 1 stereo, unbalanced

DVI 201 A D Rx ....................... 1 stereo, balanced/unbalanced

Connectors

DVI 201 A D Tx ........................ (1) 3.5 mm mini audio jack (tip, ring, sleeve)

DVI 201 A D Rx ....................... (1) 3.5 mm captive screw connector, 5 pole

Impedance

DVI 201 A D Tx ........................ >10k ohms unbalanced, DC coupled

DVI 201 A D Rx ....................... >18k ohms unbalanced, 14k ohms balanced, DC coupled

Nominal level

DVI 201 A D Tx ........................ -10 dBV (316 mVrms)

DVI 201 A D Rx ....................... +4 dBu (1.23 Vrms)

Maximum level

DVI 201 A D Tx ........................ +11 dBu, unbalanced at 1% THD+N

DVI 201 A D Rx ....................... +16.8 dBu, unbalanced at 1% THD+N

NOTE: 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu

Audio output — DVI 201 A D Tx/Rx

Number/signal type

DVI 201 A D Tx ........................ 1 stereo, balanced/unbalanced

DVI 201 A D Rx ....................... 1 stereo, unbalanced

Connectors

DVI 201 A D Tx ........................ (1) 3.5 mm captive screw connector, 5 pole

DVI 201 A D Rx ....................... (1) 3.5 mm mini audio jack (tip, ring, sleeve)

Impedance

DVI 201 A D Tx ........................ 50 ohms unbalanced, 100 ohms balanced

DVI 201 A D Rx ....................... 50 ohms unbalanced

Maximum level (Hi-Z)

DVI 201 A D Tx ........................ >+16 dBu, balanced or unbalanced at 1% THD+N

DVI 201 A D Rx ....................... >+9.8 dBu, unbalanced at 1% THD+N

Maximum level (600 ohm)

DVI 201 A D Tx ........................ >+9 dBm, balanced or unbalanced at 1% THD+N

DVI 201 A D Rx ....................... >+6.8 dBm, unbalanced at 1% THD+N

Control/remote — external device (pass-through)

Serial control port input

Transmitter .............................. RS-232 via (1) 3.5 mm, 3 pole captive screw connector

Receiver .................................. 1 set of proprietary signals on a female RJ-45 jack

Serial control port output

Transmitter .............................. 1 set of proprietary signals on a female RJ-45 jack

Receiver .................................. RS-232 via a 3.5 mm, 3 pole captive screw connector

NOTE: Protocol is mirrored between the transmitter and the receiver.

Serial control pin configuration ....... Captive screw connectors: 1 = Tx, 2 = Rx, 3 = GND

Extron DVI 201/201 A D Tx/Rx DVI/HDMI Extender Series Transmitters/Receivers • Specifications 2

General

Power supply ................................. External

Input: 100-240 VAC, 50-60 Hz

Output: 12 VDC, 1 A, 12 watts

Power consumption

DVI 201 Tx .............................. 2.8 watts, 12 VDC

DVI 201 Rx .............................. 4.0 watts, 12 VDC

DVI 201 A D Tx ........................ 3.0 watts, 12 VDC

DVI 201 A D Rx ....................... 4.2 watts, 12 VDC

NOTE: Each transmitter or receiver can be powered either locally by an external power supply or remotely by receiver or transmitter on the other end of the CAT 5/5e/6 or Extron STP201 cable.

Temperature/humidity .................... Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing

Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing

Cooling .......................................... Convection, no vents

Mounting

Rack mount ............................. DVI 201: with optional 1U rack shelf

Furniture mount ....................... DVI 201: with optional through-desk mounting kit

Furniture or wall mount ............ DVI 201 A D: with a 1 gang wall box or mud ring

Pole mount .............................. DVI 201: with optional mounting kit

Enclosure type ............................... Metal

Enclosure dimensions

DVI 201 Tx/Rx ......................... 1.0" H x 4.3" W x 3.0" D (quarter rack wide)

(2.5 cm H x 10.9 cm W x 7.6 cm D)

(Depth excludes connectors.)

DVI 201 A D Tx/Rx

Faceplate ........................... 2.6" H* x 1.3" W x 0.1" D

(6.6 cm H* x 3.3 cm W x 0.3 cm D)

(Fits the opening in a 1 gang decorator-style wallplate.)

*Overall height is 4.1" (10.4 cm) including mounting tabs. Mounting holes are 3.8"

[9.5 cm] apart on center.

Buffer ................................. 2.7" H x 1.8" W x 0.75" D

(6.9 cm H x 4.6 cm W x 1.9 cm D)

(Depth excludes connectors.)

Product weight .............................. 0.5 lbs (0.3 kg)

Vibration ........................................ ISTA 1A in carton (International Safe Transit Association)

Regulatory compliance

Safety ...................................... CE, c-UL, KCC (non-decorator-style only), UL

EMI/EMC

DVI 201 Tx/Rx ................... CE**, C-tick, FCC Class A**, ICES, VCCI, KCC

DVI 201 A D Tx/Rx............. CE**, C-tick, FCC Class A**, ICES, VCCI

NOTE: **CE and FCC testing is conducted with STP (shielded twisted pair) cable.

Warranty ........................................ 3 years parts and labor

NOTE: All nominal levels are at ±10%.

NOTE: Specifications are subject to change without notice.

NOTE: Shipping weights and dimensions are available at www.extron.com

.

CMS-041017-D24

Extron DVI 201/201 A D Tx/Rx DVI/HDMI Extender Series Transmitters/Receivers • Specifications 3

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement