AMC7135
350mA ADVANCED CURRENT REGULATOR
www.addmtek.com
DESCRIPTION
FEATURES
The AMC7135 is a low dropout current regulator
rated for 350mA constant sink current. The low quiescent
current and low dropout voltage is achieved by advanced
Bi-CMOS process.
„
350mA constant sink current.
„
Output short / open circuit protection.
„
Low dropout voltage.
„
Low quiescent current
„
Supply voltage range 2.7V ~ 6V
„
2KV HBM ESD protection
„
Advanced Bi-CMOS process.
„
SOT-89 and TO-252 package
TYPICAL APPLICATION CIRCUIT
APPLICATIONS
„
Supply
Voltage
2.7V ~ 6V
Power LED driver
PACKAGE PIN OUT
C BP
VDD
OUT
VDD
VDD
GND
GND
AMC7135
OUT
GND
OUT
SOT-89
TO-252
(Top View)
ORDER INFORMATION
IOUT
PK
SOT-89
SJ
3-pin
TO-252
3-pin
340-380mA
AMC7135PKF
AMC7135SJF
300-340mA
AMC7135PKFA
AMC7135SJFA
Note:
1. All surface-mount packages are available in Tape & Reel. Append the letter “T” to part number (i.e. AMC7135PKFAT).
2. The letter ”F” is marked for Lead Free process.
3. The letter ”A” is marked for current ranking.
Copyright © 2007 ADDtek Corp.
1
DD031_C --
APRIL 2007
AMC7135
ABSOLUTE MAXIMUM RATINGS (Note)
-0.3V to 7V
-0.3V to 7V
150OC
-40OC to 150OC
260OC
Input Voltage, VDD
Output Voltage, VOUT
Maximum Junction Temperature, TJ
Storage Temperature Range
Lead Temperature (Soldering, 10 seconds)
Note:
Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground.
Currents are positive into, negative out of the specified terminal.
BLOCK DIAGRAM
VDD
AMC7135
Band-gap
Reference
OUT
Control
Circuit
GND
PIN DESCRIPTION
Pin Name
Pin Function
VDD
Power supply.
OUT
Output pins. Connected to load.
GND
Ground.
Copyright © 2007 ADDtek Corp.
2
DD031_C
--
APRIL 2007
AMC7135
RECOMMENDED OPERATING CONDITIONS
Parameter
Supply Voltage
Output Sink Current
Operating Free-air Temperature Range
Symbol
Min
VDD
IOUT
TA
2.7
Typ
-40
Max
Unit
6
400
+85
V
mA
℃
DC ELECTRICAL CHARACTERISTICS
VDD=3.7V, TA=25°C, No Load, ( Unless otherwise noted)
Parameter
Symbol
Output Sink Current
ISINK
Condition
Min
Typ
Max
Unit
VOUT=0.2V
340
360
380
mA
VOUT=0.2V, Rank A
300
320
340
mA
Apply
Pin
Load Regulation
VOUT=0.2V to 3V
3
mA/V
Line Regulation
VDD= 3V to 6V,
VOUT=0.2V
3
mA/V
Output Dropout Voltage
VOUTL
120
mV
Supply Current Consumption
IDD
200
uA
OUT
VDD
Note 1: Output dropout voltage: 90% x IOUT @ VOUT=200mV
TYPICAL OPERATION CHRACTERISTICS
QUIESCENT CURRENT vs. TEMP
QUIESCENT CURRENT vs. SUPPLY VOLTAGE
0.17
0.22
0.16
0.2
0.15
0.18
IQ (mA)
IQ (mA)
0.14
0.13
0.16
0.14
0.12
0.12
0.11
0.1
0.10
2
2.5
3
3.5
20
4
40
60
80
100
TEMP (ºC)
VIN (V)
OUT CURRENT vs.OUT_DROPOUT VOLTAGE
400
350
OUT (mA)
300
250
200
150
100
50
0
0.01
0.1
1
10
OUT_DROPOUT (V)
Copyright © 2007 ADDtek Corp.
3
DD031_C
--
APRIL 2007
AMC7135
APPLICATION INFORMATION
The Maximum Power Dissipation on Regulator:
PD(MAX) = VOUT(MAX) × IOUT(NOM) + VIN(MAX) × IQ
VOUT(MAX) = the maximum voltage on output pin;
IOUT(NOM) = the nominal output current;
IQ = the quiescent current the regulator consumes at IOUT(MAX);
VIN(MAX) = the maximum input voltage.
Thermal Consideration:
The maximum junction temperature ratings of AMC7135 should not be exceeded under continuous normal load
conditions. When power consumption is over about 700mW (SOT-89 package, at TA=70°C) or 1000mW (TO-252
package, at TA=70°C), additional heat sink is required to control the junction temperature below 120°C.
The junction temperature is:
TJ = PD (θJT +θCS +θSA ) + TA
PD : Dissipated power.
θJT: Thermal resistance from the junction to the mounting tab of the package.
θCS: Thermal resistance through the interface between the IC and the surface on which it is mounted.
(typically, θCS < 1.0°C /W)
θSA: Thermal resistance from the mounting surface to ambient (thermal resistance of the heat sink).
If PC Board copper is going to be used as a heat sink, below table can be used to determine the appropriate size
of copper foil required. For multi-layered PCB, these layers can also be used as a heat sink. They can be connected with
several through-hole vias.
PCB θSA (°C /W)
PCB heat sink size (mm2)
Copyright © 2007 ADDtek Corp.
59
500
45
1000
38
1500
4
33
2000
27
3000
24
4000
DD031_C
21
5000
--
APRIL 2007
AMC7135
PACKAGE
Copyright © 2007 ADDtek Corp.
5
DD031_C
--
APRIL 2007
AMC7135
IMPORTANT NOTICE
ADDtek reserves the right to make changes to its products or to discontinue any integrated circuit product or service
without notice, and advises its customers to obtain the latest version of relevant information to verify, before placing
orders, that the information being relied on is current.
A few applications using integrated circuit products may involve potential risks of death, personal injury, or severe
property or environmental damage. ADDtek integrated circuit products are not designed, intended, authorized, or
warranted to be suitable for use in life-support applications, devices or systems or other critical applications. Use of
ADDtek products in such applications is understood to be fully at the risk of the customer. In order to minimize risks
associated with the customer’s applications, the customer should provide adequate design and operating safeguards.
ADDtek assumes to no liability to customer product design or application support. ADDtek warrants the performance of
its products to the specifications applicable at the time of sale.
ADDtek Corp.
9F, No. 20, Sec. 3, Bade Rd., Taipei, Taiwan, 105
TEL: 2-25700299
FAX: 2-25700196
Copyright © 2007 ADDtek Corp.
6
DD031_C
--
APRIL 2007
Download PDF
Similar pages