User Manual
HD-HPC-SP-TX / HD-HPCWP-TX
100m HDBaseT HDMI and VGA 2x1 Switcher / Extender
244 Bergen Boulevard, Woodland Park, NJ 07424  Tel 973-785-4347  FAX
973-785-3318  Web: www.fsrinc.com
43106
LIT1550D
Important Safety Instructions
Contents are subject to change without notice
Warnings
To reduce the risk of fire, electric shock or product damage:
1. Do not expose this device to
rain, moisture, dripping or
6. Clean this device only
with dry cloth.
splashing and that no objects
filled with liquids, such as vases,
shall be placed on the unit.
2. Do not install or place this unit
7. Unplug this device
in a bookcase, built-in cabinet or
during lightning storms or
in another confined space.
when unused for long
Ensure the unit is well ventilated.
periods of time.
3. To prevent risk of electric
shock or fire hazard due to
overheating, do not obstruct
the unit’s ventilation openings
with newspapers, tablecloths,
curtains, and similar items.
8. Protect cables and
cords from being walked
on or pinched particularly
at plugs.
4. Do not install near any heat
sources such as radiators, heat
registers, stoves, or other device
(including amplifiers) that
9. Only use
attachments/accessories
specified by FSR.
produce heat.
5. Do not place sources of open
10. Refer all servicing to
flames, such as lighted candles,
qualified service
on the unit.
personnel.
2
Table of Contents
Overview .................................................................................................. 4 Features ................................................................................................... 5 Package Contents .................................................................................... 6 HD-HPC-SP-Tx and HD-HPCWP-Tx sold separately .............................. 6 HD-HPC-SP-Tx ........................................................................................ 6 Typical Application .................................................................................... 7 Typical Application .................................................................................... 8 Dimensions .............................................................................................. 9 HD-HPCWP-Tx ................................................................................. 9 HD-HPC-SP-Tx ................................................................................. 9 HD-HPC-SP-Tx Front Panel ................................................................... 10 HD-HPCWP-Tx Front Panel ....................................................................11 ................................................................................................................11 HD-HPC-SP-Tx Rear Panel ................................................................... 12 HD-HPCWP-Tx Rear Panel ................................................................... 13 Hardware Installation.............................................................................. 14 Input Select Button and switching behavior............................................ 15 Dip Switch Description ........................................................................... 16 VGA EDID Switch Setting ............................................................... 16 HDMI EDID ..................................................................................... 16 SET (HD-HPC-SP-Tx only) ............................................................. 17 IR and RS-232 Operation ....................................................................... 18 IR Control ........................................................................................ 18 RS-232 Control and Firmware Updates .......................................... 20 Specifications ......................................................................................... 21 Limited Warranty .................................................................................... 23 3
OVERVIEW
The HD-HPC-SP-Tx transmitter is a true HDBaseT 5-Play device that transmits
HD Video (up to 4k at 30Hz), Audio, Bi-directional control (IR & RS-232), Ethernet,
and Power via 1 CAT-6A shielded cable up to 100 Meters.
The HD-HPC-SP-Tx works with any of FSR’s 100 Meter HDBaseT Receivers and
can be powered from either end (Tx to Rx or Rx to Tx). The HD-HPC-SP-Tx’s
switcher has both HDMI and VGA with Audio.
The switcher has built-in auto-sensing circuitry to switch to the active source. It
can be manually triggered using the front panel Input Select Button or via contact
closure on the rear screw terminals (HD-HPC-SP-Tx only).
The HD-HPCWP-Tx is a 2-gang wallplate version of the HD-HPC-SP-Tx and fits
in a standard 2-gang box.
4
FEATURES

Transmission distance for 1080p over Cat 5e/6 reaches up to 100 meters.
4K reaches up to 70 meters

Supports VGA input (with L/R audio) and HDMI input

Switches the input source simply by pressing the button on the front panel or
contact closure via pluggable screw terminal connector (HD-HPC-SP-Tx
only) on the rear panel

Automatically switches to an active source

HDBT 2.0 compliance

HDMI 1.4 with 4K compliance

Bi-directional PoE (HD-HPC-SP-Tx only)

Bi-directional IR

IR, Ethernet and RS232 control over HDBT

Space saving design
Note:
The actual signal transmission distance can vary and depends on signal
resolution, cable quality, graphics card, and display used in the system.
5
PACKAGE CONTENTS
HD-HPC-SP-TX AND HD-HPCWP-TX SOLD SEPARATELY
HD-HPC-SP-TX
One HD-HPC-SP-Tx Transmitter
Two 2-pin screw-down terminals
One 3-pin screw-down terminal
One IR Emitter
One IR Receiver (30kHz ~ 50kHz)
Two Under Table Mounting Brackets
User's manual
HD-HPCWP-TX
One HD-HPCWP-TX Transmitter
One 9-pin screw-down terminal
Four 6-32x1/4 Flat head screws
One cover plate and cover plate screws
User's manual
6
TYPICAL APPLICATION
HD-HPC-SP-Tx shown
NOTE: It is only necessary to power one side (Tx or Rx)
Transmitters do not include a Power Supply. An FSR 17762 Power Supply is
included with any of the FSR HDBaseT Receivers. Only one power supply is
needed to power the Transmitter and Receiver set. FSR 17762 Power Supplies
can also be ordered separately.
7
TYPICAL APPLICATION
HD-HPCWP-Tx shown
Transmitter
Receiver
NOTE: Only one power supply is needed to power the Transmitter and Receiver
set from any of the FSR's 100m HDBaseT receivers. The HD-HPCWP-Tx
transmitter can be powered locally but it cannot send power to the receiver.
Transmitters do not include a Power Supply. An FSR 17762 Power Supply is
included with any of the FSR HDBaseT Receivers. FSR 17762 Power Supplies
can also be ordered separately.
8
DIMENSIONS
HD-HPCWP-Tx
HD-HPC-SP-Tx
9
HD-HPC-SP-TX FRONT PANEL
3
1
2
6
4
5
7
ID
Name
Description
1
SET
RS-232 Settings (See table)
2
EDID
VGA resolution settings (See table)
3
Power LED
4
Status LED
5
HDCP LED
6
Link LED
On: Unit is powered on.
Off: Unit is powered off.
Intermittent: Normal operating condition
Off: Fault
On: HDCP video is being transmitted.
Off/Intermittent: No HDCP video is being transmitted
ON: Receiver and Transmitter are linked to each other
OFF/Intermittent: Fault in unit(s) or cabling.
Input select button to select the input source.
7
Input Select
The function is the same with input select (pluggable
screw terminal connector) in the front panel. See
"Select Button and switching behavior"
10
HD-HPCWP-TX FRONT PANEL
6
5
4
7
1
8
3
10
9
2
ID
Name
Description
1
VGA IN
HD-15 VGA input
2
EDID
VGA resolution settings (See table)
3
AUDIO
Stereo audio input
4
HDMI LED
Indicates HDMI input is selected
5
VGA LED
Indicates VGA input is selected
6
HDCP LED
7
Link LED
8
Input Select
9
HDMI IN
HDMI input
10
IR SENSOR
Sensor for remote control
On: HDCP video is being transmitted.
Off/Intermittent: No HDCP video is being transmitted
ON: Receiver and Transmitter are linked to each other
OFF/Intermittent: Fault in unit(s) or cabling.
Input select button used to select the input source.
See "Select Button and switching behavior"
11
HD-HPC-SP-TX REAR PANEL
5
1
ID
1
Name
Power
2
3
4
6
7
8
9
10
Description
12V 2A DC power supply input (power supply sold
separately. (See note under "Typical Application")
2
HDBT OUT
Connects to HDBT IN port of receiver
3
HDMI IN
Connects to an HDMI source
4
Input Select
Pluggable screw terminal connector connecting to an
external control pad (HD-HPC-SP-Tx only).
See "Select Button and switching behavior"
5
IR IN
Connects to IR receiver
6
IR OUT
Connects to IR transmitter
7
RS-232
Serial port (See table)
8
ETHERNET
Connects to an Ethernet device
9
VGA IN
Connects to a VGA source
10
Audio IN
Audio input, embedded stereo in VGA audio
12
HD-HPCWP-TX REAR PANEL
6
5
1
2
3
4
ID
1
Name
POWER IN
Description
12V 2A DC power supply input (power supply sold
separately. (See note under "Typical Application")
2
POWER OUT
12VDC 250mA max
3
RS-232
Serial port
4
IR OUT
Connects to IR transmitter
5
ETHERNET
Connects to an Ethernet device
6
HDBT OUT
Connects to HDBT IN port of receiver
13
HARDWARE INSTALLATION
Warnings

Before the installation, disconnect the power supply from all the
devices.

Do not connect or disconnect cables from the Transmitter and
Receiver while they are powered ON. To connect or disconnect
cables from the units, power them OFF first.

For best resolution and ESD performance, a shielded CAT6A in a
TIA / EIA 568B wiring configuration is recommended. Please use
care when installing, connecting and disconnecting cables.
1.
Connect the source to the HDMI IN and/or VGA IN on the Transmitter.
2.
Connect the IR emitter to the IR OUT and the IR Receiver to the IR IN on
both the Transmitter and Receiver.
3.
Connect a Display to the HDMI OUT on the Receiver.
4.
Connect the HDBT OUT on the Transmitter to the HDBT IN on the Receiver
via a shielded CAT5e / CAT6 / CAT6A / CAT7 cable.
5.
Connect the power supply.
14
INPUT SELECT BUTTON AND SWITCHING BEHAVIOR
The auto switcher will select an active input or the first-come first-served if both
inputs are active.
The input select switch or the contact closure (HD-HPC-SP-Tx only) can select
the input type only if both inputs are active.
Key function description:
1. If HDMI IN and VGA IN are both connected to the source devices, and HDMI IN
is selected as current source, pressing the input select button will switch to VGA
as source. If VGA the source is unplugged, it will switch back to HDMI IN
automatically.
2. If only HDMI IN is connected to the source device, and HDMI IN is selected as
current source, pressing the input select button will have no effect and it will
remain as HDMI IN.
15
DIP SWITCH DESCRIPTION
VGA EDID Switch Setting
NOTE:
HD-HPC-SP-TX AND HD-HPCWP-TX HAVE OPPOSITE DIP SWITCH
LOGIC FOR THE "ON" POSITION AS SHOWN BELOW:
HD-HPC-SP-TX (DOWN IS "ON")
HD-HPCWP-SP-TX (DOWN IS "OFF")
ON
1 2 3
ON
1 2
3
Position
1
Position
2
Position
3
Resolution
0
0
0
1280 x 800 60Hz
0
0
1
1920 x 1200 60Hz
0
1
0
1920 x 1080 60Hz (Default)
0
1
1
1280 x 720 60Hz
1
0
0
1024 x 768 60Hz
1
0
1
800 x 600 60Hz
1
1
0
Reserved
1
1
1
Reserved
0 = OFF and 1 = ON
Note:
Power cycle the extender after you change the switch position.
HDMI EDID
HD-HPC-SP-Tx: Pass-through or 1080p 60Hz if a sink is not detected.
HD-HPCWP-Tx: Pass-through
16
SET (HD-HPC-SP-Tx only)
1
2
ON
Position
1
Position
2
Position
3
0
0
0
1
0
0
3
Settings
RS-232 pass-through enabled
(Default)
Valens IC update
RS-232 pass-through disabled
0
1
0
MCU update and control
RS-232 pass-through disabled
0 = OFF (UP) and 1 = ON (DOWN)
17
IR AND RS-232 OPERATION
(HD-HPC-SP-Tx shown)
IR Control
The IR pass-through feature on the Transmitter and Receiver allows you to
control the Source from the Display’s location or vice versa.
Scenario 1
The TV can be controlled from the Transmitter’s location with the TV remote.
The IR receiver is connected to the IR IN on the Transmitter and the IR emitter is
connected to the IR OUT on the Receiver.
TV REMOTE
IR RECEIVER
CABLE
BLUE-RAY
DVD
DC 12V
-
+ -
+
LOCAL OUT
HDMI IN
IR IN
IR OUT
Tx Rx
HDBaseT
HD-H-SP-Rx shown (ordered seperately)
+
DC 12V
NORMAL
+ -
IR IN
IR OUT
Tx Rx
UPDATE
HDMI OUT
TV
IR EMITTER
CABLE
18
VGA IN
L/R
Scenario 2
The DVD Player can be controlled from the Receiver’s location with the DVD
Player Remote. The IR emitter is connected to the IR OUT on the Transmitter and
the IR receiver is connected to the IR IN on the Receiver.
BLUE-RAY
DVD
IR EMITTER
CABLE
DC 12V
-
+ -
+
LOCAL OUT
HDMI IN
IR IN
IR OUT
Tx Rx
HDBaseT
HD-H-SP-Rx
+
DC 12V
NORMAL
+ -
IR IN
IR OUT
Tx Rx
UPDATE
HDMI OUT
TV
IR RECEIVER
CABLE
DVD REMOTE
19
VGA IN
L/R
RS-232 Control and Firmware Updates
The RS-232 port can be used as a pass-through to control a device connected to
the Transmitter from the Receiver or vice versa. In addition, the RS-232 port on
the Transmitter can be connected to a computer to update the firmware. (See Dip
switch settings)
Scenario 1: Firmware Update
(HD-HPC-SP-Tx only)
DC 12V
-
+ -
+
HDMI IN
LOCAL OUT
IR IN
IR OUT
Tx Rx
VGA IN
L/R
Scenario 2: RS-232 Control
Maximum baud rate is 115.2 Kbps.
RS-232 DEVICE
Set switch to NORMAL
DC 12V
-
+ -
+
LOCAL OUT
HDMI IN
IR IN
IR OUT
Tx Rx
HDBaseT
Set switch to NORMAL
HD-H-SP-Rx shown (ordered seperately)
+
DC 12V
NORMAL
+ -
IR IN
IR OUT
Tx Rx
HDMI OUT
RS-232 DEVICE
20
UPDATE
VGA IN
L/R
SPECIFICATIONS
Technical
Video input
1 HDMI,
Connectors
1 VGA (HD-15 female) with 1/8" Stereo
Input Signal Types
HDMI 1.4 and HDCP compliant up to 4K2K 30Hz
7.1ch audio
VGA + Audio up to 1920 x 1200 60Hz.
Output
1 HDBT
Output Signal Type
HDBT Video Impedance
100Ω
Control
Control input
RS-232 via 3.81mm 3 Pin pluggable screw terminal
Connector
Switch closure via 3.81mm 3 Pin pluggable screw
terminal Connector (HD-HPC-SP-Tx only)
Front Panel pushbutton switch
IR input and output via 1/8" jack (DV-HPC-SP-Tx)
IR output via 3.81mm pluggable screw terminal
Maximum Pixel
297MHz
Clock
Operating
Temperature
32°F to 95°F (0°C to 35°C)
10% to 90%, non-condensing
Temperature
-4°F to 140°F (-20°C to 70°C)
10% to 90%, non-condensing
Power Supply
DC 12V 2A (power supply sold separately)
ESD Protection
Human-body Model:
Storage
±8kV (Air-gap discharge)
±4kV (Contact discharge)
Surge Protection
IEC 61000-4-4 (EFT) 40A (5/50ns); IEC 61000-4-5
(Lightning) 25A (8/20μs)
21
Cable Specifications
For best resolution and ESD performance Shielded CAT6A in a TIA / EIA
568B wiring configuration is recommended.
Cable Type
Range
Supported Video
CAT5e/CAT6
100m
1080p 60Hz (36 bpp)
70m
1080p 60Hz (48 bpp)
1080p 60Hz 3D
4K 2160p (3840x2160 30Hz)
CAT6A/CAT7
100m
1080p 60Hz (36 bpp)
1080p 60Hz (48 bpp)
1080p 60Hz 3D
4K 2160p (3840x2160 30Hz)
General
Shipping
HD-HPCWP-Tx: 1.45 lbs. (0.66 kg)
Weight
HD-HPC-SP-Tx:
Dimension
See dimension drawings for specific model information
2.45 lbs. (1.12 kg)
(W x H x D)
22
LIMITED WARRANTY
The HD-HPC-SP-Tx, HD-HPCWP-SP-Tx 100m HDBaseT HDMI and VGA 2x1 Switcher /
Extender are warranted against failures due to defective parts or faulty workmanship for a
period of three years after delivery to the original owner. During this period, FSR will make
any necessary repairs or replace the unit without charge for parts or labor. Shipping charges
to the factory or repair station must be prepaid by the owner, return-shipping charges (via
UPS Ground) will be paid by FSR.
This warranty applies only to the original owner and is not transferable. In addition, it does
not apply to repairs done by other than the FSR factory or Authorized Repair Stations.
This warranty shall be cancelable by FSR at its sole discretion if the unit has been subjected
to physical abuse or has been modified in any way without written authorization from FSR.
FSR’s liability under this warranty is limited to repair or replacement of the defective unit.
FSR will not be responsible for incidental or consequential damages resulting from the use
or misuse of its products. Some states do not allow the exclusion of incidental or
consequential damages, so the above limitations may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state.
Warranty claims should be accompanied by a copy of the original purchase invoice showing
the purchase date (if a Warranty Registration Card was mailed in at the time of purchase,
this is not necessary). Before returning any equipment for repair, please read the important
information on service below.
SERVICE
Before returning any equipment for repair, please be sure that it is adequately packed and
cushioned against damage in shipment, and that it is insured. We suggest that you save the
original packaging and use it to ship the product for servicing. Also, please enclose a note
giving your name, address, phone number and a description of the problem.
NOTE: all equipment being returned for repair must have a Return authorization (RMA)
Number. To get a RMA Number, please call the FSR Service Department
(1-800-332-FSR1).
Please display your RMA Number prominently on the front of all packages.
CONTACT INFORMATION:
FSR INC.
244 Bergen Blvd.
Woodland Park, NJ 07424
Phone:
(973) 785-4347
Order Desk Fax: (973) 785-4207
Web Site: http://www.fsrinc.com
23
Download PDF
Similar pages