HP FlexFabric 11900 Switch Series

QuickSpecs
HP FlexFabric 11900 Switch Series
Overview
Models
HP FlexFabric 11908-V Switch Chassis
JG608A
Key features
High-performance CLOS-based switching architecture
Large layer 2 scaling with TRILL and HP IRF
Feature-rich routing with IPv4/IPv6, MPLS, and QoS
Enhanced modularity with control and data plane separation
High 10GbE and 40GbE density; 100GbE ready across 7.7 Tb/s switch fabric
Product overview
The HP FlexFabric 11900 Switch Series is a high-performance data center aggregation switch that provides line-rate, high-density
10GbE and 40GbE connectivity designed for cost-effective end-of-row (EoR) and small core deployments.
With latency as low as 3 µs, the HP FlexFabric 11900 Switch Series can scale to 384 1/10GbE, 192 1/10GBASE-T, 64 40GbE or 16
100GbE ports. The switch delivers up to 7.7 Tbps switching capacity and 5.8 Bpps forwarding throughput. A broad variety of interface
options is available, including 1/10GbE, 1/10GBASE-T, 40GbE and 100GbE.
Ready for software-defined networking (SDN), the switch supports full Layer 2 and 3 features, including advanced features such as
transparent Interconnection of Lots of Links (TRILL) and Intelligent Resilient Framework (IRF), which provides the ability to build
large, resilient switching fabrics. The HP FlexFabric 11900 Switch Series also supports fully redundant and hot-swappable
components to complement its other enterprise-class capabilities.
Features and benefits
Data center optimized
Scalable Layer 2 fabrics
builds flexible, resilient and scalable Layer 2 fabrics with TRILL together with HP IRF
NEW Multitenant Device Context (MDC)
virtualizes a physical switch into multiple logical devices, with each logical switch having its own processes, configuration, and
administration
Data Center Bridging (DCB) protocols
supports IEEE 802.1Qaz Data Center Bridging Exchange (DCBX) and Enhanced Transmission Selection (ETS) and IEEE 802.1Qbb
Priority Flow Control (PFC) for converged fabrics
Fibre Channel over Ethernet (FCoE) capabilities
delivers support for FCoE, including expansion, fabric, trunk VF and N ports, and aggregation of E-port and N-port
virtualization
Edge Virtual Bridging (EVB) with Virtual Ethernet Port Aggregator (VEPA) support
provides connectivity into the virtualization-ready data center environment
Front-to-back airflow design
accomodates deployment in data centers utilizing hot-cold aisles
Performance
High-performance fully-distributed architecture
delivers up to 7.7 Tbps switching capacity and 5.76 Bpps throughput with non-blocking wire-speed performance and latency
as low as 3 microseconds
High-density 1/10GbE and 40GbE interface connectivity
offers up to eight interface module slots to scale up to 384 1GbE/10GbE and 64 40GbE ports
Scalable system design
provides investment protection to support future technologies and higher-speed connectivity, as the switch is designed for
DA - 14585 Worldwide QuickSpecs — Version 10 — 12.12.2014
Page 1
QuickSpecs
HP FlexFabric 11900 Switch Series
Overview
increased backplane bandwidth
Product architecture
Advanced Comware modular operating system
brings native high stability, independent process monitoring and restart through the modular design and multiple processes of
HP Comware v7 software; supports enhanced serviceability functions
In-Service Software Upgrade (ISSU)
provides an upgrade of the entire chassis, or an individual task or process, with zero packet loss
Distributed architecture with separation of data and control planes
delivers enhanced fault tolerance and facilitates continuous operation and zero service disruption during planned or
unplanned control-plane events
Resiliency and high availability
Intelligent Resilient Framework (IRF)
creates virtual resilient switching fabrics, where two or more switches perform as a single L2 switch and L3 router; switches do
not have to be co-located and can be part of a disaster-recovery system; servers or switches can be attached using standard
LACP for automatic load balancing and high availability; can eliminate the need for complex protocols like Spanning Tree
Protocol, Equal-Cost Multipath (ECMP), or VRRP, thereby simplifying network operation
Redundant/load-sharing fabrics, management, fan assemblies, and power supplies
increases total performance and power available while providing hitless, stateful failover
Hot-swappable modules
allows replacement of modules without any impact on other modules
Graceful restart
allows routers to indicate to others their capability to maintain a routing table during a temporary shutdown and significantly
reduces convergence times upon recovery; supports OSPF, BGP, and IS-IS
Virtual Router Redundancy Protocol (VRRP)
allows groups of two routers to dynamically back each other up to create highly available routed environments
Device Link Detection Protocol (DLDP)
monitors link connectivity and shuts down ports at both ends if unidirectional traffic is detected, preventing loops in STPbased networks
Hitless patch upgrades
allows patches and new service features to be installed without restarting the equipment, increasing network uptime and
facilitating maintenance
IEEE 802.3ad Link Aggregation Control Protocol (LACP)
supports up to 1024 trunk groups and up to 16 members per trunk; supports static or dynamic groups and a user-selectable
hashing algorithm
Passive design system
delivers increased system reliability as backplane has no active components
Ultrafast protocol convergence (subsecond) with standard-based failure detection—Bidirectional Forwarding Detection
(BFD)
enables link connectivity monitoring and reduces network convergence time for RIP, OSPF, BGP, IS-IS, VRRP, MPLS, and IRF
Layer 2 switching
VLAN
supports up to 4,094 port-based or IEEE 802.1Q-based VLANs; also supports MAC-based VLANs, protocol-based VLANs, and
IP-subnet-based VLANs for added flexibility
Bridge Protocol Data Unit (BPDU) tunneling
transmits Spanning Tree Protocol BPDUs transparently, allowing correct tree calculations across service providers, WANs, or
MANs
Port mirroring
duplicates port traffic (ingress and egress) to a local or remote monitoring port; supports four mirroring groups, with an
unlimited number of ports per group
Spanning Tree Protocol (STP)
supports standard IEEE 802.1D STP, IEEE 802.1w Rapid Spanning Tree Protocol (RSTP) for faster convergence, and IEEE
DA - 14585 Worldwide QuickSpecs — Version 10 — 12.12.2014
Page 2
QuickSpecs
HP FlexFabric 11900 Switch Series
Overview
802.1s Multiple Spanning Tree Protocol (MSTP)
Internet Group Management Protocol (IGMP) and Multicast Listener Discovery (MLD) protocol snooping
controls and manages the flooding of multicast packets in a Layer 2 network
IEEE 802.1ad QinQ and selective QinQ
increase the scalability of an Ethernet network by providing a hierarchical structure; connect multiple LANs on a high-speed
campus or metro network
Per-VLAN Spanning Tree Plus (PVST+)
allows each VLAN to build a separate spanning tree to improve link bandwidth usage in network environments with multiple
VLANs
Isolation at data link layer with private VLANs
provides, through a two-tier VLAN structure, an additional layer of protection, simplifying network configuration while saving
VLAN resources
Layer 3 routing
Open shortest oath first (OSPF)
delivers faster convergence; uses this link-state routing Interior Gateway Protocol (IGP), which supports ECMP, NSSA, and MD5
authentication for increased security and graceful restart for faster failure recovery
Intermediate system to intermediate system (IS-IS)
uses a path vector Interior Gateway Protocol (IGP), which is defined by the ISO organization for IS-IS routing and extended by
IETF RFC 1195 to operate in both TCP/IP and the OSI reference model (Integrated IS-IS)
Border Gateway Protocol 4 (BGP-4)
delivers an implementation of the Exterior Gateway Protocol (EGP) utilizing path vectors; uses TCP for enhanced reliability for
the route discovery process; reduces bandwidth consumption by advertising only incremental updates; supports extensive
policies for increased flexibility; scales to very large networks
Multiprotocol Label Switching (MPLS)
uses BGP to advertise routes across Label Switched Paths (LSPs), but uses simple labels to forward packets from any Layer 2
or Layer 3 protocol, which reduces complexity and increases performance; supports graceful restart for reduced failure
impact; supports LSP tunneling and multilevel stacks
Dual IP stack
maintains separate stacks for IPv4 and IPv6 to ease the transition from an IPv4-only network to an IPv6-only network design
Equal-Cost Multipath (ECMP)
enables multiple equal-cost links in a routing environment to increase link redundancy and scale bandwidth
Policy-based routing
makes routing decisions based on policies set by the network administrator
Static IPv4 routing
provides simple manually configured IPv4 routing
Routing Information Protocol (RIP)
uses a distance vector algorithm with UDP packets for route determination; supports RIPv1 and RIPv2 routing; includes loop
protection
IP performance optimization
provides a set of tools to improve the performance of IPv4 networks; includes directed broadcasts, customization of TCP
parameters, support of ICNP error packets, and extensive display capabilities
Unicast Reverse Path Forwarding (uRPF)
limits erroneous or malicious traffic in accordance with RFC 3074
Static IPv6 routing
provides simple, manually configured IPv6 routing Routing Information Protocol next generation (RIPng) extends RIPv2 to
support IPv6 addressing
OSPFv3
provides OSPF support for IPv6
IS-IS for IPv6
extends IS-IS to support IPv6 addressing
BGP+
extends BGP-4 to support Multiprotocol BGP (MBGP), including support for IPv6 addressing
Multiprotocol Label Switching (MPLS) Layer 3 VPN
allows Layer 3 VPNs across a provider network; uses MP-BGP to establish private routes for increased security; supports RFC
2547bis multiple autonomous system VPNs for added flexibility
DA - 14585 Worldwide QuickSpecs — Version 10 — 12.12.2014
Page 3
QuickSpecs
HP FlexFabric 11900 Switch Series
Overview
Multiprotocol Label Switching (MPLS) Layer 2 VPN
establishes simple Layer 2 point-to-point VPNs across a provider network using only MPLS Label Distribution Protocol (LDP);
requires no routing and therefore decreases complexity, increases performance, and allows VPNs of non-routable protocols;
uses no routing information for increased security; supports Circuit Cross Connect (CCC), Static Virtual Circuits (SVCs), Martini
draft, and Kompella-draft technologies
Virtual Private LAN Service (VPLS)
establishes point-to-multipoint Layer 2 VPNs across a provider
network
IPv6 tunneling
provides an important element for the transition from IPv4 to IPv6; allows IPv6 packets to traverse IPv4-only networks by
encapsulating the IPv6 packet into a standard IPv4 packet; supports manually configured, 6to4, Intra-Site Automatic Tunnel
Addressing Protocol (ISATAP) tunnels, and IPv6 on VPN to Provider Edge (6VPE) router tunnel
Quality of Service (QoS)
IEEE 802.1p prioritization
delivers data to devices based on the priority and type of traffic
Flexible classification
creates traffic classes based on access control lists (ACLs), IEEE 802.1p precedence, IP, and DSCP or Type of Service (ToS)
precedence; supports filter, redirect, mirror, remark, and logging
Bandwidth shaping
Port-based rate limiting
provides per-port ingress-/egress-enforced increased bandwidth
Classifier-based rate limiting
uses an access control list (ACL) to enforce increased bandwidth
for ingress traffic on each port
Reduced bandwidth
provides per-port, per-queue egress-based reduced bandwidth
Broad QoS feature set
provides support for Strict Priority Queuing (SP), Weighted Fair Queuing (WFQ), Weighted Deficit Round Robin(WDRR),
SP+WDRR together, configurable buffers, Explicit Congestion Notification (ECN), and Weighted Random Early Detection
(WRED)
Traffic policing
supports Committed Access Rate (CAR) and line rate
Layer 3 services
Address Resolution Protocol (ARP)
determines the MAC address of another IP host in the same subnet; supports static ARPs; gratuitous ARP allows detection of
duplicate IP addresses; proxy ARP allows normal ARP operation between subnets or when subnets are separated by a Layer 2
network
User Datagram Protocol (UDP) helper
redirects UDP broadcasts to specific IP subnets to prevent server spoofing
Dynamic Host Configuration Protocol (DHCP)
simplifies the management of large IP networks and supports client and server; DHCP Relay enables DHCP operation across
subnets
Management
Management interface control
enables or disables each of the following interfaces depending on security preferences: console port, telnet port, or reset
button
Industry-standard CLI with a hierarchical structure
reduces training time and expenses, and increases productivity in multivendor installations
SNMPv1, v2, and v3
provide complete support of SNMP; provide full support of industry-standard Management Information Base (MIB) plus private
extensions; SNMPv3 supports increased security using encryption
DA - 14585 Worldwide QuickSpecs — Version 10 — 12.12.2014
Page 4
QuickSpecs
HP FlexFabric 11900 Switch Series
Overview
sFlow (RFC 3176)
provides scalable ASIC-based wirespeed network monitoring and accounting with no impact on network performance; this
allows network operators to gather a variety of sophisticated network statistics and information for capacity planning and
real-time network monitoring purposes
Remote monitoring (RMON)
uses standard SNMP to monitor essential network functions; supports events, alarm, history, and statistics group plus a
private alarm extension group
Debug and sampler utility
supports ping and traceroute for both IPv4 and IPv6
Network Time Protocol (NTP)
synchronizes timekeeping among distributed time servers and clients; keeps timekeeping consistent among all clockdependent devices within the network so that the devices can provide diverse applications based on the consistent time
Network Quality Analyzer (NQA)
analyzes network performance and service quality by sending test packets, and provides network performance and service
quality parameters such as jitter, TCP, or FTP connection delays and file transfer rates; allows a network manager to
determine overall network performance and to diagnose and locate network congestion points or failures
Information center
provides a central information center for system and network information; aggregates all logs, traps, and debugging
information generated by the system and maintains them in order of severity; outputs the network information to multiple
channels based on user-defined rules
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
advertises and receives management information from adjacent devices on a network, facilitating easy mapping by network
management applications
Connectivity
Jumbo frames
allows high-performance backups and disaster-recovery systems with a maximum frame size of 9k bytes
Loopback
supports internal loopback testing for maintenance purposes and an increase in availability; loopback detection protects
against incorrect cabling or network configurations and can be enabled on a per-port or per-VLAN basis for added flexibility
Ethernet operations, administration and maintenance (OAM)
detects data link layer problems that occurred in the "last mile" using the IEEE 802.3ah OAM standard; monitors the status of
the link between two devices
Monitor link
collects statistics on performance and errors on physical links, increasing system availability
Packet storm protection
protects against unknown broadcast, unknown multicast, or unicast storms with user-defined thresholds
Flow control
provides back pressure using standard IEEE 802.3x, reducing congestion in heavy traffic situations
Security
Access control list (ACL)
supports powerful ACLs for both IPv4 and IPv6; ACLs are used for filtering traffic to prevent unauthorized users from accessing
the network, or for controlling network traffic to save resources; rules can either deny or permit traffic to be forwarded; rules
can be based on a Layer 2 header or a Layer 3 protocol header; rules can be set to operate on specific dates or times
Remote Authentication Dial-In User Service (RADIUS)
eases switch security access administration by using a password authentication server
Terminal Access Controller Access-Control System (TACACS+)
delivers an authentication tool using TCP with encryption of the full authentication request, providing additional security
Secure shell (SSHv2)
uses external servers to securely log in to a remote device; with authentication and encryption, it protects against IP spoofing
and plain-text password interception; increases the security of Secure FTP (SFTP) transfers
DHCP snooping
helps ensure that DHCP clients receive IP addresses from authorized DHCP servers and maintain a list of DHCP entries for
trusted ports; prevents reception of fake IP addresses and reduces ARP attacks, improving security
DA - 14585 Worldwide QuickSpecs — Version 10 — 12.12.2014
Page 5
QuickSpecs
HP FlexFabric 11900 Switch Series
Overview
IP Source Guard
filters packets on a per-port basis, which prevents illegal packets from being forwarded
ARP attack protection
protects against attacks that use a large number of ARP requests, using a host-specific, user-selectable threshold
Port security
allows access only to specified MAC addresses, which can be learned or specified by the administrator
IEEE 802.1X support
provides port-based user authentication with support for Extensible Authentication Protocol (EAP) MD5, TLS, TTLS, and PEAP
with choice of AES, TKIP, and static or dynamic WEP encryption for protecting wireless traffic between authenticated clients
and the access point
Multiple user authentication methods
IEEE 802.1X
uses an IEEE 802.1X supplicant on the client in conjunction with a RADIUS server to authenticate in accordance with
industry standards
Web-based authentication
provides a browser-based environment, similar to IEEE 802.1X, to authenticate clients that do not support the IEEE
802.1X supplicant
MAC-based authentication
authenticates the client with the RADIUS server based on the client's MAC address
Multicast support
Internet Group Management Protocol (IGMP)
utilizes Any-Source Multicast (ASM) or Source-Specific Multicast (SSM) to manage IPv4 multicast networks; supports IGMPv1,
v2, and v3
Protocol Independent Multicast (PIM)
defines modes of Internet IPv4 and IPv6 multicasting to allow one-to-many and many-to-many transmission of information;
PIM Dense Mode (DM), Sparse Mode (SM), and Source-Specific Mode (SSM) are supported
Multicast Source Discovery Protocol (MSDP)
allows multiple PIM-SM domains to interoperate; is used for inter-domain multicast applications
Multicast Border Gateway Protocol (MBGP)
allows multicast traffic to be forwarded across BGP networks separately from unicast traffic
Integration
VPN 20Gbps 11900 Firewall Module
provides enhanced stateful packet inspection and filtering; supports flexible security zones and virtual firewall containment;
delivers advanced VPN services with 3DES and AES encryption at high performance and low latency; offers Web content
filtering and application prioritization and optimization
Warranty and support
1-year warranty
advance hardware replacement with 10-calendar-day delivery (available in most countries)
Electronic and telephone support
limited electronic and business-hours telephone support is available from HP for the entire warranty period; to reach our
support centers, refer to www.hp.com/networking/contact-support; for details on the duration of support provided with
your product purchase, refer to www.hp.com/networking/warrantysummary
Software releases
to find software for your product, refer to www.hp.com/networking/support; for details on the software releases available
with your product purchase, refer to www.hp.com/networking/warrantysummary
DA - 14585 Worldwide QuickSpecs — Version 10 — 12.12.2014
Page 6
QuickSpecs
HP FlexFabric 11900 Switch Series
Configuration
Build To Order: BTO is a standalone unit with no integration. BTO products ship standalone are not part of a CTO or RackShippable solution.
HP FF 11908-V Switch Chassis
Must select min 1 Interface Module
Must select min 4 Fabric Modules
Must select min 1 Management Module
Must select min 1 Power Supply
20U - Height
JG608A
Internal Power Supplies
System (std 0 // max 6) User Selection (min 1 // max 6) per switch enclosure
HP FF 11900 2500W AC Power Supply
includes 1 x c19, 2500w
JG616A
See Configuration
Note:1, 2, 3
NOTE: 11900 provides 5+1 Redundancy. Select an appropriate number of power supplies based on the
maximum output power of your system and redundancy requirements. For component power consumption
consult the install guide.
PDU Cable NA/MEX/TW/JP
" C19 PDU Jumper Cord (NA/MEX/TW/JP)
JG616A#B2B
PDU Cable ROW
C19 PDU Jumper Cord (ROW)
JG616A#B2C
High Volt Switch to Wall Power Cord
NEMA L6-20P Cord
JG616A#B2E
HP FF 11900 2400W DC Power Supply
NEMA L6-20P Cord
JG617A
See Configuration
Note:1, 6
Configuration Rules
Note 1
If more than 1 power supply is selected they, must all be the same Sku number.
Note 2
Localization required on orders without #B2B, #B2C or #B2E options.
Note 3
#B2E is Offered only in NA, Mexico, Taiwan and Japan.
Note 6
One of these cables is required when ordering this power supply: (Use #B01 if switch is CTO) - if applicable
HP 10500 -48V 3m DC Power Supply Cable
JG390A
HP 10500 -48V 15m DC Power Supply Cable
JG391A
Remarks:
Drop down under power supply should offer the following options and results:
Switch/Router/Power Supply to PDU Power Cord - #B2B in North America, Mexico, Taiwan, and Japan or
#B2C ROW. (Watson Default B2B or B2C for Rack Level CTO)
Switch/Router/Power Supply to Wall Power Cord - Localized Option (Watson Default for BTO and Box Level
CTO)
DA - 14585 Worldwide QuickSpecs — Version 10 — 12.12.2014
Page 7
QuickSpecs
HP FlexFabric 11900 Switch Series
Configuration
High Volt Switch/Router/Power Supply to Wall Power Cord - #B2E Option. (Offered only in North America,
Mexico, Taiwan, and Japan)
Modules
Interface Modules
System (std 0 // max 8) User Selection (min 1 // max 8) per enclosure
HP FF 11900 24p 1/10GBASE-T SF Mod
No Transceivers
HP FF 11900 32p 10GbE SFP+ SF Mod
min=0 \ max=32 SFP+ Transceivers
HP FF 11900 48p 10GbE SFP+ SF Mod
min=0 \ max=48 SFP+ Transceivers
HP FF 11900 4p 40GbE QSFP+ SF Mod
min=0 \ max=4 QSFP+ Transceivers
HP FF 11900 8p 40GbE QSFP+ SF Mod
min=0 \ max=8 QSFP+ Transceivers
HP FF 11900 2p 100GbE CFP SE Mod
min=0 \ max=2 CFP Transceivers
HP 10500/11900/7500 20Gbps VPN FW Mod
min=0 \ max=2 SFP Transceivers
HP 10500/7500 20G Unified Wired-WLAN Mod
No supported Transceivers
JG615A
JG611A
See Configuration
Note:1, 2, 4
JG612A
See Configuration
Note:1, 2
JG613A
See Configuration
Note:3
JG614A
See Configuration
Note:3
JG918A
See Configuration
Note:8
JG372A
See Configuration
Note:5
JG639A
See Configuration
Note:7
Configuration Rules
Note 1
The following Transceivers install into this Module:
HP X170 1G SFP LC LH70 1550 Transceiver
HP X170 1G SFP LC LH70 1570 Transceiver
HP X170 1G SFP LC LH70 1590 Transceiver
HP X170 1G SFP LC LH70 1610 Transceiver
HP X170 1G SFP LC LH70 1470 Transceiver
HP X170 1G SFP LC LH70 1490 Transceiver
HP X170 1G SFP LC LH70 1510 Transceiver
HP X170 1G SFP LC LH70 1530 Transceiver
HP X120 1G SFP LC LH100 Transceiver
DA - 14585 Worldwide QuickSpecs — Version 10 — 12.12.2014
JD109A
JD110A
JD111A
JD112A
JD113A
JD114A
JD115A
JD116A
JD103A
Page 8
QuickSpecs
HP FlexFabric 11900 Switch Series
Configuration
Note 2
Note 3
Note 4
Note 5
HP X125 1G SFP LC LH40 1310nm Transceiver
HP X120 1G SFP LC LH40 1550nm Transceiver
HP X120 1G SFP RJ45 T Transceiver
HP X120 1G SFP LC SX Transceiver
HP X120 1G SFP LC LX Transceiver
HP X125 1G SFP LC LH70 Transceiver
HP X120 1G SFP LC BX 10-U Transceiver
HP X120 1G SFP LC BX 10-D Transceiver
JD061A
JD062A
JD089B
JD118B
JD119B
JD063B
JD098B
JD099B
The following Transceivers install into this Module:
HP X130 10G SFP+ LC SR Transceiver
HP X130 10G SFP+ LC LR Transceiver
HP X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable
HP X240 10G SFP+ SFP+ 7m Direct Attach Copper Cable
HP X130 10G SFP+ LC ER 40km Transceiver
JD092B
JD094B
JD095C
JD096C
JD097C
JG081C
JC784C
JG234A
The following 40G Transceivers install into this Module:
HP X140 40G QSFP+ LC LR4 SM 10km 1310nm Transceiver
HP X140 40G QSFP+ MPO SR4 Transceiver
HP X140 40G QSFP+ MPO MM 850nm CSR4 300m Transceiver
HP X240 40G QSFP+ QSFP+ 3m Direct Attach Copper Cable
HP X240 40G QSFP+ QSFP+ 5m Direct Attach Copper Cable
HP X240 40G QSFP+ to 4x10G SFP+ 1m Direct Attach Copper Splitter Cable
HP X240 40G QSFP+ to 4x10G SFP+ 3m Direct Attach Copper Splitter Cable
HP X240 40G QSFP+ to 4x10G SFP+ 5m Direct Attach Copper Splitter Cable
JG661A
JG325B
JG709A
JG327A
JG328A
JG329A
JG330A
JG331A
The following Transceivers install into this Module:
HP X130 10G SFP+ LC LRM Transceiver
JD093B
The following Transceivers install into this Module:
HP X125 1G SFP LC LH40 1310nm Transceiver
HP X120 1G SFP LC LH40 1550nm Transceiver
HP X125 1G SFP LC LH70 Transceiver
HP X120 1G SFP LC SX Transceiver
HP X120 1G SFP LC LX Transceiver
JD061A
JD062A
JD063B
JD118B
JD119B
Note 7
Maximum of this Module per Chassis:
JG608A min=0\max=7 per Chassis
There are no restrictions on which slots these modules may go in.
Note 8
The following Transceivers install into this Module:
HP X150 100G CFP LC LR4 10km SM XCVR
JG829A
Fabric Modules
System (std 0 // max 4) User Selection (min 4 // max 4) per enclosure
HP FF 11908 1.92Tbps Type D Fabric Mod
DA - 14585 Worldwide QuickSpecs — Version 10 — 12.12.2014
JG610A
Page 9
QuickSpecs
HP FlexFabric 11900 Switch Series
Configuration
No supported Transceivers
Management Modules
System (std 0 // max 2) User Selection (min 1 // max 2) per enclosure
HP FF 11900 Main Processing Unit
Remarks:
JG609A
These modules can only be inserted into Slots 4 and 5.
Transceivers
SFP Transceivers
HP X120 1G SFP RJ45 T Transceiver
HP X120 1G SFP LC BX 10-U Transceiver
HP X120 1G SFP LC BX 10-D Transceiver
HP X120 1G SFP LC LH100 Transceiver
HP X120 1G SFP LC LH40 1550nm XCVR
HP X120 1G SFP LC SX Transceiver
HP X120 1G SFP LC LX Transceiver
HP X125 1G SFP LC LH40 1310nm XCVR
HP X125 1G SFP LC LH70 Transceiver
HP X170 1G SFP LC LH70 1550 Transceiver
HP X170 1G SFP LC LH70 1570 Transceiver
HP X170 1G SFP LC LH70 1590 Transceiver
HP X170 1G SFP LC LH70 1610 Transceiver
HP X170 1G SFP LC LH70 1470 Transceiver
HP X170 1G SFP LC LH70 1490 Transceiver
HP X170 1G SFP LC LH70 1510 Transceiver
HP X170 1G SFP LC LH70 1530 Transceiver
JD089B
JD098B
JD099B
JD103A
JD062A
JD118B
JD119B
JD061A
JD063B
JD109A
JD110A
JD111A
JD112A
JD113A
JD114A
JD115A
JD116A
SFP+ Transceivers
HP X130 10G SFP+ LC SR Transceiver
HP X130 10G SFP+ LC LRM Transceiver
HP X130 10G SFP+ LC LR Transceiver
HP X130 10G SFP+ LC ER 40km Transceiver
HP X240 10G SFP+ SFP+ 0.65m DAC Cable
HP X240 10G SFP+ SFP+ 1.2m DAC Cable
HP X240 10G SFP+ SFP+ 3m DAC Cable
HP X240 10G SFP+ SFP+ 5m DAC Cable
HP X240 10G SFP+ 7m DAC Cable
JD092B
JD093B
JD094B
JG234A
JD095C
JD096C
JD097C
JG081C
JC784C
QSFP+ Transceivers
HP X140 40G QSFP+ LC LR4 SM XCVR
HP X140 40G QSFP+ MPO SR4 XCVR
HP X140 40G QSFP+ CSR4 300m XCVR
HP X240 40G QSFP+ QSFP+ 1m Direct Attach Copper Cable
HP X240 40G QSFP+ QSFP+ 3m Direct Attach Copper Cable
DA - 14585 Worldwide QuickSpecs — Version 10 — 12.12.2014
JG661A
JG325B
JG709A
JG326A
JG327A
Page 10
QuickSpecs
HP FlexFabric 11900 Switch Series
Configuration
HP X240 40G QSFP+ QSFP+ 5m Direct Attach Copper Cable
HP X240 QSFP+ 4x10G SFP+ 1m Direct Attach Copper Cable
HP X240 QSFP+ 4x10G SFP+ 3m Direct Attach Copper Cable
HP X240 QSFP+ 4x10G SFP+ 5m Direct Attach Copper Cable
JG328A
JG329A
JG330A
JG331A
CFP Transceivers
HP X150 100G CFP LC LR4 10km SM XCVR
JG829A
Switch Enclosure Options
Mounting Kit
HP X421 Chassis Universal Rck Mntg Kit
JC665A
See Configuration
Note:1
Configuration Rules
Note 1
If any 11900 switch is installed into a rack, Then this Rack Mounting kit is required.
Remarks:
Default a quantity of 1 when Switch is selected.
Software Licenses
HP Unified Wired-WLAN 128 AP E-LTU
(min 0 // max 7)
REMARK: This license is for use with the Primary Controllers.
JG649AAE
See Configuration
Note:1
HP Unified Wired-WLAN 128 AP Redundant E-LTU
(min 0 // max 7)
REMARK: This license is for use with the Redundant Controllers.
JG902AAE
See Configuration
Note:1
Configuration Rules
Note 1
Only supported on JG639A and JG645A.
Remarks:
JG649AAE is optional to increase the AP by a count of 128 per E-LTU
JG902AAE - Redundant access point licenses are intended for use only on a
redundant controller module in a 1+1 or N+1 configuration or when extra access
point capacity is required for failover in an N+N configuration.
Fans
HP FF 11908-V Spare Fan Assy
JG618A
Power Supply Cables
(std 0 // max 1) User Selection (min 1 // max 1) per DC Power Supply
HP 10500 -48V 3m DC Power Supply Cable
DA - 14585 Worldwide QuickSpecs — Version 10 — 12.12.2014
JG390A
Page 11
QuickSpecs
HP FlexFabric 11900 Switch Series
Configuration
HP 10500 -48V 15m DC Power Supply Cable
DA - 14585 Worldwide QuickSpecs — Version 10 — 12.12.2014
JG391A
Page 12
QuickSpecs
HP FlexFabric 11900 Switch Series
Technical Specifications
HP FlexFabric 11908-V Switch Chassis (JG608A)
I/O ports and slots
8 I/O module slots
Supports a maximum of 384 1/10GbE ports or 192 1/10GBASE-T ports or 64 40GbE ports, or a
combination
Additional ports and slots 2 MPU (for management modules) slots
4 switch fabric slots
Power supplies
6 power supply slots
1 minimum power supply required (ordered separately)
Fan tray
includes: 1 x JC634A
1 fan tray slot
Physical characteristics Dimensions
17.32(w) x 25.98(d) x 34.88(h) in (43.99 x 65.99 x 88.6 cm) (20U height)
Weight
169.53 lb (76.9 kg) chassis
Full configuration weight 331.31 lb (150.28 kg)
Memory and processor
Management module
Mounting
Mounts in an EIA-standard 19 in. rack or other equipment cabinet (hardware included); horizontal surface
mounting only
Throughput
up to 5.8 Bpps (64-byte packets
Performance
Dual Core MIPS64 @ 1.2 GHz, 512 MB flash, 8 GB DDR2 SDRAM
Switching capacity
7.7 Tbps
Routing table size
16384 entries (IPv4), 8192 entries (IPv6)
MAC address table size
131072 entries
Reliability
Availability
99.999%
Environment
Operating temperature
32°F to 113°F (0°C to 45°C)
Operating relative
humidity
10% to 95%, noncondensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
5% to 95%, noncondensing
Altitude
up to 13,123 ft (4 km)
Acoustic
Low-speed fan: 61.6 dB, High-speed fan: 72.6 dB
Electrical characteristics AC Voltage
Safety
Emissions
Immunity
100-120/200-240 VAC, depending on configuration
DC Voltage
-48 to -60 VDC, depending on configuration
Current
16/60 A
Power output
2500 W
Frequency
50/60 Hz
Notes
Based on a common power supply of 2,500 W (AC)
CAN/CSA 22.2 No. 60950-1; FCC Part 15, Subpart B; FDA 21 CFR Subchapter J; ROHS Compliance; IEC
60950-1 :Second Edition ; EN 60950-1:2006 + A11:2009; AS/NZS 60950-1; IEC 60825-1; UL 60950-1, 2nd
Edition; EN60825-2:2004+A1:2007
VCCI Class A; EN 55022 Class A; CISPR 22 Class A; IEC/EN 61000-3-2; IEC/EN 61000-3-3; ICES-003 Class A;
AS/NZS CISPR 22 Class A; FCC (CFR 47, Part 15) Class A; GB9254
Generic
Directive 2004/108/EC
EN
EN 55024:1998+ A1:2001 + A2:2003; ETSI EN 300 386 V1.3.3
ESD
EN 61000-4-2
Radiated
EN 61000-4-3
EFT/Burst
EN 61000-4-4
DA - 14585 Worldwide QuickSpecs — Version 10 — 12.12.2014
Page 13
QuickSpecs
HP FlexFabric 11900 Switch Series
Technical Specifications
Management
Services
Surge
EN 61000-4-5
Conducted
EN 61000-4-6
Power frequency
magnetic field
IEC 61000-4-8
Voltage dips and
interruptions
EN 61000-4-11
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
IMC - Intelligent Management Center; command-line interface; out-of-band management (serial RS-232C);
SNMP Manager; Telnet; terminal interface (serial RS-232C); modem interface; IEEE 802.3 Ethernet MIB;
Ethernet Interface MIB
Refer to the HP website at: www.hp.com/networking/services for details on the service-level
descriptions and product numbers. For details about services and response times in your area, please
contact your local HP sales office.
Standards and protocols BGP
(applies to all products in RFC 1771 BGPv4
series)
RFC 1772 Application of the BGP
RFC 1997 BGP Communities Attribute
RFC 1998 PPP Gandalf FZA Compression Protocol
RFC 2385 BGP Session Protection via TCP MD5
RFC 2439 BGP Route Flap Damping
RFC 2796 BGP Route Reflection
RFC 2858 BGP-4 Multi-Protocol Extensions
RFC 2918 Route Refresh Capability
RFC 3065 Autonomous System Confederations for
BGP
RFC 3392 Capabilities Advertisement with BGP-4
RFC 4271 A Border Gateway Protocol 4 (BGP-4)
RFC 4272 BGP Security Vulnerabilities Analysis
RFC 4273 Definitions of Managed Objects for BGP-4
RFC 4274 BGP-4 Protocol Analysis
RFC 4275 BGP-4 MIB Implementation Survey
RFC 4276 BGP-4 Implementation Report
RFC 4277 Experience with the BGP-4 Protocol
RFC 4360 BGP Extended Communities Attribute
RFC 4456 BGP Route Reflection: An Alternative to
Full Mesh Internal BGP (IBGP)
RFC 5291 Outbound Route Filtering Capability for
BGP-4
RFC 5292 Address-Prefix-Based Outbound Route
Filter for BGP-4
RFC 3315 DHCPv6 (client and relay)
RFC 3484 Default Address Selection for IPv6
RFC 3513 IPv6 Addressing Architecture
RFC 3736 Stateless Dynamic Host Configuration
Protocol (DHCP) Service for IPv6
RFC 3810 MLDv2 for IPv6
RFC 4214 Intra-Site Automatic Tunnel Addressing
Protocol (ISATAP)
RFC 4861 IPv6 Neighbor Discovery
RFC 4862 IPv6 Stateless Address Auto-configuration
MIBs
RFC 1156 (TCP/IP MIB)
RFC 1157 A Simple Network Management Protocol
(SNMP)
RFC 1215 A Convention for Defining Traps for use
with the SNMP
RFC 1229 Interface MIB Extensions
RFC 1493 Bridge MIB
RFC 1573 SNMP MIB II
RFC 1643 Ethernet MIB
RFC 1657 BGP-4 MIB
RFC 1724 RIPv2 MIB
RFC 1907 SNMPv2 MIB
RFC 2011 SNMPv2 MIB for IP
RFC 2012 SNMPv2 MIB for TCP
RFC 2013 SNMPv2 MIB for UDP
RFC 2096 IP Forwarding Table MIB
RFC 2233 Interface MIB
Denial of service protection
Automatic filtering of well-known denial-of-service RFC 2452 IPV6-TCP-MIB
RFC 2454 IPV6-UDP-MIB
packets
RFC 2465 IPv6 MIB
CPU DoS Protection
RFC 2466 ICMPv6 MIB
Rate Limiting by ACLs
RFC 2571 SNMP Framework MIB
RFC 2572 SNMP-MPD MIB
Device management
RFC 2573 SNMP-Target MIB
RFC 1157 SNMPv1/v2c
RFC 2578 Structure of Management Information
RFC 1305 NTPv3
Version
RFC 1902 (SNMPv2)
2 (SMIv2)
RFC 2579 (SMIv2 Text Conventions)
RFC 2580 Conformance Statements for SMIv2
RFC 2580 (SMIv2 Conformance)
RFC 2819 (RMON groups Alarm, Event, History and RFC 2618 RADIUS Client MIB
DA - 14585 Worldwide QuickSpecs — Version 10 — 12.12.2014
Page 14
QuickSpecs
HP FlexFabric 11900 Switch Series
Technical Specifications
RFC 2620 RADIUS Accounting MIB
RFC 2665 Ethernet-Like-MIB
RFC 2668 802.3 MAU MIB
RFC 2674 802.1p and IEEE 802.1Q Bridge MIB
RFC 2787 VRRP MIB
RFC 2819 RMON MIB
RFC 2925 Ping MIB
RFC 2932IP (Multicast Routing MIB)
RFC 2933 IGMP MIB
General protocols
RFC 2934 Protocol Independent Multicast MIB for
IEEE 802.1ad Q-in-Q
IPv4
IEEE 802.1ag Service Layer OAM
RFC 3414 SNMP-User based-SM MIB
IEEE 802.1p Priority
RFC 3415 SNMP-View based-ACM MIB
IEEE 802.1Q VLANs
RFC 3417 Simple Network Management Protocol
IEEE 802.1s Multiple Spanning Trees
IEEE 802.1w Rapid Reconfiguration of Spanning Tree(SNMP) over IEEE 802 Networks
RFC 3418 MIB for SNMPv3
IEEE 802.1X PAE
RFC 3595 Textual Conventions for IPv6 Flow Label
IEEE 802.3ab 1000BASE-T
RFC 3621 Power Ethernet MIB
IEEE 802.3ac (VLAN Tagging Extension)
RFC 3813 MPLS LSR MIB
IEEE 802.3ad Link Aggregation Control Protocol
RFC 3814 MPLS FTN MIB
(LACP)
RFC 3815 MPLS LDP MIB
IEEE 802.3ae 10-Gigabit Ethernet
RFC 3826 AES for SNMP's USM MIB
IEEE 802.3ah Ethernet in First Mile over Point to
RFC 4133 Entity MIB (Version 3)
Point Fiber - EFMF
RFC 4444 Management Information Base for
IEEE 802.3ba 40 and 100 Gigabit Ethernet
Intermediate System to Intermediate System (IS-IS)
Architecture
Statistics only)
HTTP, SSHv1, and Telnet
Multiple Configuration Files
Multiple Software Images
SSHv1/SSHv2 Secure Shell
TACACS/TACACS+
Web UI
IEEE 802.3x Flow Control
MPLS
IEEE 802.3z 1000BASE-X
RFC 2205 Resource ReSerVation Protocol
RFC 768 UDP
RFC 2209 Resource ReSerVation Protocol (RSVP)
RFC 783 TFTP Protocol (revision 2)
RFC 2702 Requirements for Traffic Engineering Over
RFC 791 IP
MPLS
RFC 792 ICMP
RFC 2858 Multiprotocol Extensions for BGP-4
RFC 793 TCP
RFC 2961 RSVP Refresh Overhead Reduction
RFC 826 ARP
Extensions
RFC 854 TELNET
RFC 3031 Multiprotocol Label Switching Architecture
RFC 894 IP over Ethernet
RFC 3032 MPLS Label Stack Encoding
RFC 925 Multi-LAN Address Resolution
RFC 950 Internet Standard Subnetting Procedure RFC 3107 Carrying Label Information in BGP-4
RFC 3212 Constraint-Based LSP Setup using LDP
RFC 959 File Transfer Protocol (FTP)
RFC 3479 Fault Tolerance for the Label Distribution
RFC 1027 Proxy ARP
RFC 1035 Domain Implementation and Specification Protocol (LDP)
RFC 3487 Graceful Restart Mechanism for LDP
RFC 1042 IP Datagrams
RFC 3564 Requirements for Support of
RFC 1058 RIPv1
RFC 1142 OSI IS-IS Intra-domain Routing Protocol Differentiated
Service-aware MPLS Traffic Engineering
RFC 1195 OSI ISIS for IP and Dual Environments
RFC 4364 BGP/MPLS IP Virtual Private Networks
RFC 1213 Management Information Base for
(VPNs)
Network
RFC 4379 Detecting Multi-Protocol Label Switched
Management of TCP/IP-based internets
(MPLS) Data Plane Failures
RFC 1293 Inverse Address Resolution Protocol
RFC 4447 Pseudowire Setup and Maintenance Using
RFC 1305 NTPv3
LDP
RFC 1350 TFTP Protocol (revision 2)
RFC 4448 Encapsulation Methods for Transport of
RFC 1393 Traceroute Using an IP Option
Ethernet over MPLS Networks
RFC 1519 CIDR
RFC 4664 Framework for Layer 2 Virtual Private
RFC 1531 Dynamic Host Configuration Protocol
Networks
RFC 1533 DHCP Options and BOOTP Vendor
RFC 4665 Service Requirements for Layer 2 Provider
Extensions
Provisioned Virtual Private Networks
RFC 1591 DNS (client only)
RFC 4761 Virtual Private LAN Service (VPLS) Using
RFC 1624 Incremental Internet Checksum
BGP for Auto-Discovery and Signaling
RFC 1701 Generic Routing Encapsulation
DA - 14585 Worldwide QuickSpecs — Version 10 — 12.12.2014
Page 15
QuickSpecs
HP FlexFabric 11900 Switch Series
Technical Specifications
RFC 4762 Virtual Private LAN Service (VPLS) Using
RFC 1721 RIP-2 Analysis
Label
RFC 1723 RIP v2
Distribution Protocol (LDP) Signaling
RFC 1812 IPv4 Routing
RFC 5036 LDP Specification
RFC 2082 RIP-2 MD5 Authentication
RFC 2091 Trigger RIP
Network management
RFC 2131 DHCP
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
RFC 2138 Remote Authentication Dial In User Service
RFC 1155 Structure of Management Information
(RADIUS)
RFC 1157 SNMPv1
RFC 2236 IGMP Snooping
RFC 1448 Protocol Operations for version 2 of the
RFC 2338 VRRP
Simple Network Management Protocol (SNMPv2)
RFC 2453 RIPv2
RFC 2211 Controlled-Load Network
RFC 2644 Directed Broadcast Control
RFC 2819 Four groups of RMON: 1 (statistics), 2
RFC 2763 Dynamic Name-to-System ID mapping
(history), 3 (alarm) and 9 (events)
support
RFC 3176 sFlow
RFC 2784 Generic Routing Encapsulation (GRE)
RFC 3411 SNMP Management Frameworks
RFC 2865 Remote Authentication Dial In User Service
RFC 3412 SNMPv3 Message Processing
(RADIUS)
RFC 3414 SNMPv3 User-based Security Model (USM)
RFC 2966 Domain-wide Prefix Distribution with
RFC 3415 SNMPv3 View-based Access Control Model
Two-Level IS-IS
VACM)
RFC 2973 IS-IS Mesh Groups
ANSI/TIA-1057 LLDP Media Endpoint Discovery
RFC 3022 Traditional IP Network Address Translator
(LLDP-MED)
(Traditional NAT)
RFC 3277 IS-IS Transient Blackhole Avoidance
OSPF
RFC 3567 Intermediate System to Intermediate
RFC 1245 OSPF protocol analysis
System (IS-IS) Cryptographic Authentication
RFC 1246 Experience with OSPF
RFC 3719 Recommendations for Interoperable
RFC 1765 OSPF Database Overflow
Networks using Intermediate System to
RFC 1850 OSPFv2 Management Information Base
Intermediate System (IS-IS)
(MIB), traps
RFC 3784 ISIS TE support
RFC 2154 OSPF w/ Digital Signatures (Password,
RFC 3786 Extending the Number of IS-IS LSP
MD-5)
Fragments
RFC 2328 OSPFv2
Beyond the 256 Limit
RFC 2370 OSPF Opaque LSA Option
RFC 3787 Recommendations for Interoperable IP
RFC 3101 OSPF NSSA
Networks using Intermediate System to
RFC 3137 OSPF Stub Router Advertisement
Intermediate System (IS-IS)
RFC 3623 Graceful OSPF Restart
RFC 3847 Restart signaling for IS-IS
RFC 3630 Traffic Engineering Extensions to OSPFv2
RFC 4251 The Secure Shell (SSH) Protocol
RFC 4061 Benchmarking Basic OSPF Single Router
Architecture
Control Plane Convergence
RFC 4486 Subcodes for BGP Cease Notification
RFC 4062 OSPF Benchmarking Terminology and
Message
Concepts
RFC 4884 Extended ICMP to Support Multi-Part
RFC 4063 Considerations When Using Basic OSPF
Messages
Convergence Benchmarks
RFC 4941 Privacy Extensions for Stateless Address
RFC 4222 Prioritized Treatment of Specific OSPF
Autoconfiguration in IPv6
Version
RFC 5130 A Policy Control Mechanism in IS-IS Using
2 Packets and Congestion Avoidance
Administrative Tags
RFC 4577 OSPF as the Provider/Customer Edge
Protocol for BGP/MPLS IP Virtual Private Networks
IP multicast
(VPNs)
RFC 2236 IGMPv2
RFC 4811 OSPF Out-of-Band LSDB
RFC 2283 Multiprotocol Extensions for BGP-4
Resynchronization
RFC 2362 PIM Sparse Mode
RFC 4812 OSPF Restart Signaling
RFC 3376 IGMPv3
RFC 4813 OSPF Link-Local Signaling
RFC 3446 Anycast Rendezvous Point (RP)
RFC 4940 IANA Considerations for OSPF
mechanism using Protocol Independent Multicast
(PIM) and Multicast Source Discovery Protocol
QoS/CoS
(MSDP)
IEEE 802.1P (CoS)
RFC 3618 Multicast Source Discovery Protocol
RFC 1349 Type of Service in the Internet Protocol
(MSDP)
DA - 14585 Worldwide QuickSpecs — Version 10 — 12.12.2014
Page 16
QuickSpecs
HP FlexFabric 11900 Switch Series
Technical Specifications
Suite
RFC 3973 PIM Dense Mode
RFC 2211 Specification of the Controlled-Load
RFC 4541 Considerations for Internet Group
Network
Management Protocol (IGMP) and Multicast Listener
Element Service
Discovery (MLD) Snooping Switches
RFC 2212 Guaranteed Quality of Service
RFC 4601 PIM Sparse Mode
RFC 2474 DSCP DiffServ
RFC 4604 Using Internet Group Management
RFC 2475 DiffServ Architecture
Protocol
RFC 2597 DiffServ Assured Forwarding (AF)
Version 3 (IGMPv3) and Multicast Listener Discovery
RFC 2598 DiffServ Expedited Forwarding (EF)
Protocol Version 2 (MLDv2) for Source-Specific
Multicast
Security
RFC 4605 IGMP/MLD Proxying
IEEE 802.1X Port Based Network Access Control
RFC 4607 Source-Specific Multicast for IP
RFC 1321 The MD5 Message-Digest Algorithm
RFC 5059 Bootstrap Router (BSR) Mechanism for
RFC 1334 PPP Authentication Protocols (PAP)
Protocol Independent Multicast (PIM)
RFC 1492 TACACS+
RFC 1994 PPP Challenge Handshake Authentication
IPv6
Protocol (CHAP)
RFC 1886 DNS Extension for IPv6
RFC 2082 RIP-2 MD5 Authentication
RFC 1887 IPv6 Unicast Address Allocation
RFC 2104 Keyed-Hashing for Message
Architecture
Authentication
RFC 1981 IPv6 Path MTU Discovery
RFC 2408 Internet Security Association and Key
RFC 2080 RIPng for IPv6
Management Protocol (ISAKMP)
RFC 2081 RIPng Protocol Applicability Statement
RFC 2409 The Internet Key Exchange (IKE)
RFC 2292 Advanced Sockets API for IPv6
RFC 2716 PPP EAP TLS Authentication Protocol
RFC 2373 IPv6 Addressing Architecture
RFC 2865 RADIUS Authentication
RFC 2375 IPv6 Multicast Address Assignments
RFC 2866 RADIUS Accounting
RFC 2460 IPv6 Specification
RFC 2868 RADIUS Attributes for Tunnel Protocol
RFC 2461 IPv6 Neighbor Discovery
Support
RFC 2462 IPv6 Stateless Address Auto-configuration
RFC 2869 RADIUS Extensions
RFC 2463 ICMPv6
Access Control Lists (ACLs)
RFC 2464 Transmission of IPv6 over Ethernet
Guest VLAN for 802.1x
Networks
MAC Authentication
RFC 2473 Generic Packet Tunneling in IPv6
Port Security
RFC 2526 Reserved IPv6 Subnet Anycast Addresses
SSHv1/SSHv2 Secure Shell
RFC 2529 Transmission of IPv6 Packets over IPv4
RFC 2545 Use of MP-BGP-4 for IPv6
VPN
RFC 2553 Basic Socket Interface Extensions for IPv6
RFC 2403 - HMAC-MD5-96
RFC 2710 Multicast Listener Discovery (MLD) for IPv6
RFC 2404 - HMAC-SHA1-96
RFC 2740 OSPFv3 for IPv6
RFC 2405 - DES-CBC Cipher algorithm
RFC 2767 Dual stacks IPv46 & IPv6
RFC 2407 - Domain of interpretation
RFC 2893 Transition Mechanisms for IPv6 Hosts and
RFC 2547 BGP/MPLS VPNs
Routers
RFC 2917 A Core MPLS IP VPN Architecture
RFC 3056 Connection of IPv6 Domains via IPv4
RFC 4302 - IP Authentication Header (AH)
Clouds
RFC 4303 - IP Encapsulating Security Payload (ESP)
RFC 3307 IPv6 Multicast Address Allocation
DA - 14585 Worldwide QuickSpecs — Version 10 — 12.12.2014
Page 17
QuickSpecs
HP FlexFabric 11900 Switch Series
Accessories
HP FlexFabric 11900 Switch Series accessories
Modules
HP FlexFabric 11900 48-port 10GbE SFP+ SF Module
HP FlexFabric 11900 32-port 10GbE SFP+ SF Module
HP FlexFabric 11900 Main Processing Unit
HP FlexFabric 11900 24-port 1/10GBASE-T SF Module
HP FlexFabric 11900 4-port 40GbE QSFP+ SF Module
HP FlexFabric 11900 8-port 40GbE QSFP+ SF Module
NEW HP FlexFabric 11900 2-port 100GbE CFP SE Module
JG612A
JG611A
JG609A
JG615A
JG613A
JG614A
JG918A
Transceivers
HP X120 1G SFP RJ45 T Transceiver
HP X120 1G SFP LC SX Transceiver
HP X120 1G SFP LC LX Transceiver
HP X125 1G SFP LC LH40 1310nm Transceiver
HP X120 1G SFP LC LH40 1550nm Transceiver
HP X125 1G SFP LC LH70 Transceiver
HP X120 1G SFP LC LH100 Transceiver
HP X120 1G SFP LC BX 10-D Transceiver
HP X120 1G SFP LC BX 10-U Transceiver
HP X170 1G SFP LC LH70 1470 Transceiver
HP X170 1G SFP LC LH70 1490 Transceiver
HP X170 1G SFP LC LH70 1510 Transceiver
HP X170 1G SFP LC LH70 1530 Transceiver
HP X170 1G SFP LC LH70 1550 Transceiver
HP X170 1G SFP LC LH70 1570 Transceiver
HP X170 1G SFP LC LH70 1590 Transceiver
HP X170 1G SFP LC LH70 1610 Transceiver
HP X130 10G SFP+ LC SR Transceiver
HP X130 10G SFP+ LC LRM Transceiver
HP X130 10G SFP+ LC LR Transceiver
HP X130 10G SFP+ LC ER 40km Transceiver
HP X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable
HP X240 10G SFP+ SFP+ 7m Direct Attach Copper Cable
HP X240 40G QSFP+ to QSFP+ 1m Direct Attach Copper Cable
HP X240 40G QSFP+ to QSFP+ 3m Direct Attach Copper Cable
HP X240 40G QSFP+ to QSFP+ 5m Direct Attach Copper Cable
HP X240 40G QSFP+ to 4x10G SFP+ 1m Direct Attach Copper Splitter Cable
HP X240 40G QSFP+ to 4x10G SFP+ 3m Direct Attach Copper Splitter Cable
HP X240 40G QSFP+ to 4x10G SFP+ 5m Direct Attach Copper Splitter Cable
HP X140 40G QSFP+ MPO SR4 Transceiver
HP X140 40G QSFP+ MPO MM 850nm CSR4 300m Transceiver
HP X150 100G CFP LC LR4 10km SM Transceiver
HP X150 100G CXP MPO SR 100m Multimode Transceiver
HP X2A0 100G CXP CXP 10m Active Optical Cable
HP X2A0 100G CXP CXP 30m Active Optical Cable
JD089B
JD118B
JD119B
JD061A
JD062A
JD063B
JD103A
JD099B
JD098B
JD113A
JD114A
JD115A
JD116A
JD109A
JD110A
JD111A
JD112A
JD092B
JD093B
JD094B
JG234A
JD095C
JD096C
JD097C
JG081C
JC784C
JG326A
JG327A
JG328A
JG329A
JG330A
JG331A
JG325B
JG709A
JG829A
JG881A
JG882A
JG883A
DA - 14585 Worldwide QuickSpecs — Version 10 — 12.12.2014
Page 18
QuickSpecs
HP FlexFabric 11900 Switch Series
Accessories
Power Supply
HP FlexFabric 11900 2500W AC Power Supply
HP FlexFabric 11900 2400W DC Power Supply
JG616A
JG617A
Mounting Kit
HP X421 Chassis Universal 4-post Rack Mounting Kit
JC665A
Power cords
HP 10500 -48V 3m DC Power Supply Cable
HP 10500 -48V 15m DC Power Supply Cable
JG390A
JG391A
Appliance
HP 10500/11900/7500 20Gbps VPN Firewall Module
JG372A
HP FlexFabric 11908-V Switch Chassis (JG608A)
HP FlexFabric 11908 1.92Tbps Type D Fabric Module
HP FlexFabric 11908-V Spare Fan Assembly
JG610A
JG618A
DA - 14585 Worldwide QuickSpecs — Version 10 — 12.12.2014
Page 19
QuickSpecs
HP FlexFabric 11900 Switch Series
Accessory Product Details
NOTE: Details are not available for all accessories. The following specifications were available at the time of publication.
Modules
HP FlexFabric 11900 Main Dimensions
Processing Unit
(JG609A)Physical
Weight
characteristics
Services
15.71(w) x 13.86(d) x 1.57(h) in (39.9 x 35.2 x
3.99 cm)
6.55 lb (2.97 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP sales
office.
HP FlexFabric 11900 32port 10GbE SFP+ SF
Module (JG611A)
32 SFP+ 1/10GbE ports
Dimensions
HP FlexFabric 11900 48port 10GbE SFP+ SF
Module (JG612A)
HP FlexFabric 11900 4port 40GbE QSFP+ SF
Module (JG613A)
HP FlexFabric 11900 8port 40GbE QSFP+ SF
Module (JG614A)
Ports
Physical characteristics
Services
15.71(w) x 13.86(d) x 1.57(h) in (39.9 x 35.2 x
3.99 cm)
Weight
7.61 lb (3.45 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP sales
office.
Ports
Physical characteristics
48 SFP+ 1/10GbE ports
Dimensions
Services
15.71(w) x 13.86(d) x 1.57(h) in (39.9 x 35.2 x
3.99 cm)
Weight
9.1 lb (4.13 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP sales
office.
Ports
Physical characteristics
4 QSFP+ 40-GbE ports
Dimensions
Services
15.71(w) x 13.86(d) x 1.57(h) in (39.9 x 35.2 x
3.99 cm)
Weight
6.92 lb (3.14 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP sales
office.
Ports
Physical characteristics
8 QSFP+ 40-GbE ports
Dimensions
Services
15.71(w) x 13.86(d) x 1.57(h) in (39.9 x 35.2 x
3.99 cm)
Weight
7.43 lb (3.37 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP sales
office.
DA - 14585 Worldwide QuickSpecs — Version 10 — 12.12.2014
Page 20
QuickSpecs
HP FlexFabric 11900 Switch Series
Accessory Product Details
Transceivers
HP X125 1G SFP LC LH40
1310nm Transceiver
(JD061A)
A small form-factor
pluggable SFP Gigabit
LH40 transceiver that
provides a full duplex
Gigabit solution up to
40km on a single-mode
fiber.
Ports
Connectivity
1 LC 1000Base-LH port (no IEEE standard exists for 1550 nm optics)
Connector type
LC
Wavelength
1310 nm
Physical characteristics Dimensions
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17
cm)
Full configuration weight 0.04 lb. (0.02 kg)
Electrical characteristics Power consumption typical0.8 W
Power consumption
1.0 W
maximum
Cabling
Cable type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:
Services
HP X120 1G SFP LC LH40
1550nm Transceiver
(JD062A)
40km distance
Fiber type
Single Mode
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP sales
office.
Ports
Connectivity
1 LC 1000BASE-LH port (no IEEE standard exists for 1550 nm optics)
Connector type
LC
Wavelength
1550 nm
Physical characteristics Dimensions
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17
A small form-factor
cm)
pluggable (SFP) Gigabit
Full configuration weight 0.04 lb. (0.02 kg)
LH40 transceiver that
Electrical
characteristics
Power consumption typical0.8 W
provides a full-duplex
Power consumption
1.0 W
Gigabit solution up to 40
maximum
km on a single mode fiber.
Cabling
Cable type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:
Services
40km distance
Fiber type
Single Mode
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP sales
office.
DA - 14585 Worldwide QuickSpecs — Version 10 — 12.12.2014
Page 21
QuickSpecs
HP FlexFabric 11900 Switch Series
Accessory Product Details
HP X125 1G SFP LC LH70
Transceiver (JD063B)
A small form-factor
pluggable (SFP) Gigabit
LH70 transceiver that
provides a full-duplex
Gigabit solution up to
70km on a single-mode
fiber.
Ports
1 LC 1000BASE-LH port (no IEEE standard exists for 1550 nm optics)
Connectivity
Connector type
LC
Wavelength
1550 nm
Physical characteristics
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17
cm)
Full configuration weight 0.04 lb. (0.02 kg)
Electrical characteristics Power consumption
typical
0.8 W
Power consumption
maximum
1.0 W
Cabling
Services
HP X125 1G SFP RJ45 T
Transceiver (JD089B)
Dimensions
Cable type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:
• 70km
Fiber type
Single Mode
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Ports
1 RJ-45 1000BASE-T port (IEEE 802.3ab Type 1000BASE-T)
Connectivity
Connector type
Physical characteristics Dimensions
A small form factor
pluggable (SFP) Gigabit
Full configuration weight
1000Base-T transceiver
that provides a full duplex Electrical characteristics Power consumption
Gigabit solution up to
typical
100m on a Cat-5+ cable.
Power consumption
maximum
Cabling
Services
RJ-45
2.71(d) x 0.54(w) x 0.55(h) in. (6.88 x 1.37 x 1.4
cm)
0.07 lb. (0.03 kg)
0.8 W
1.0 W
Cable type:
1000BASE-T: Category 5 (5E or better recommended), 100 Ù differential 4pair unshielded twisted pair (UTP) or shielded twisted pair (STP) balanced,
complying with IEEE 802.3ab 1000BASE-T;
Maximum distance:
• 100m
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 14585 Worldwide QuickSpecs — Version 10 — 12.12.2014
Page 22
QuickSpecs
HP FlexFabric 11900 Switch Series
Accessory Product Details
HP X120 1G SFP LC BX 10- Ports
U Transceiver (JD098B)
Connectivity
A small form-factor
Physical characteristics
pluggable (SFP) Gigabit LXBX10-U transceiver that
provides a full duplex
Gigabit solution up to
Electrical characteristics
10km on a single mode
cable.
Cabling
Notes
Services
HP X120 1G SFP LC BX 10- Ports
D Transceiver (JD099B)
Connectivity
A small form-factor
Physical characteristics
pluggable (SFP) Gigabit LXBX10-D transceiver that
provides a full duplex
Gigabit solution up to
Electrical characteristics
10km on a single mode
cable.
Cabling
Notes
Services
1 LC 1000BASE-BX10 port (IEEE 802.3ah Type 1000BASE-BX10-U); Duplex:
full only
Connector type
LC
Dimensions
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17
cm)
Full configuration weight 0.04 lb. (0.02 kg)
Power consumption
typical
0.8 W
Power consumption
maximum
1.0 W
Maximum distance:
• 10km
Fiber type
TX 1310nm RX 1490nm
Single Mode
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
1 LC 1000BASE-BX10 port (IEEE 802.3ah Type 1000BASE-BX10-D); Duplex:
full only
Connector type
LC
Dimensions
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17
cm)
Full configuration weight 0.04 lb. (0.02 kg)
Power consumption
typical
0.8 W
Power consumption
maximum
1.0 W
Maximum distance:
• Up to 10km
Fiber type
TX 1490nm RX 1310nm
Single Mode
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 14585 Worldwide QuickSpecs — Version 10 — 12.12.2014
Page 23
QuickSpecs
HP FlexFabric 11900 Switch Series
Accessory Product Details
HP X120 1G SFP LC LH100
Transceiver (JD103A)
A small form factor
pluggable (SFP) Gigabit
LH100 transceiver that
provides a full-duplex
Gigabit solution up to
100km on a single mode
fiber.
Ports
1 LC 1000BASE-LH port (no IEEE standard exists for 1550 nm optics)
Connectivity
Connector type
LC
Wavelength
1550 nm
Electrical characteristics Power consumption
typical
0.8 W
Power consumption
maximum
1.0 W
Cabling
Services
HP X120 1G SFP LC SX
Transceiver (JD118B)
Cable type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:
• Up to 100km
Fiber type
Single Mode
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Ports
1 LC 1000BASE-SX port
Connectivity
Connector type
LC
Wavelength
850 nm
A small form-factor
pluggable (SFP) Gigabit SX Physical characteristics
transceiver that provides a
full-duplex Gigabit solution
up to 550m on a Multimode
Electrical characteristics
fiber.
Cabling
Services
Dimensions
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17
cm)
Full configuration weight 0.04 lb. (0.02 kg)
Power consumption
typical
0.8 W
Power consumption
maximum
1.0 W
Maximum distance:
• FDDI Grade distance = 220m
• OM1 = 275m
• OM2 = 500m
• OM3 = Not Specified by standard
Cable length
up to 550m
Fiber type
Multi Mode
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 14585 Worldwide QuickSpecs — Version 10 — 12.12.2014
Page 24
QuickSpecs
HP FlexFabric 11900 Switch Series
Accessory Product Details
HP X120 1G SFP LC LX
Transceiver (JD119B)
Ports
1 SFP 1000BASE-LX port (IEEE 802.3z Type 1000BASE-LX)
Connectivity
Connector type
LC
Wavelength
1300 nm
A small form-factor
pluggable (SFP) Gigabig LX Physical characteristics
transceiver that provides a
full duplex Gigabit solution
up to 550m on MMF or
Electrical characteristics
10Km on SMF
Cabling
Services
HP 7502 Fabric Module
(JD196A)
Ports
Physical characteristics
Services
Dimensions
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17
cm)
Full configuration weight 0.04 lb. (0.02 kg)
Power consumption
typical
0.8 W
Power consumption
maximum
1.0 W
Cable type:
Either single mode or multimode;
Maximum distance:
• 550m for Multimode
• 10km for Singlemode
Fiber type
Both
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
1 RJ-45 dual-personality port; One console port, used for local or remote
configuration and management
1 RJ-45 autosensing 10/100 port (IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX); Duplex: half or full
1 Compact Flash port
Dimensions
7.83(w) x 13.98(d) x 1.77(h) in
(19.9 x 35.5 x 4.5 cm)
Weight
2.98 lb. (1.35 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Power Supplies
HP FlexFabric 11900
2500W AC Power Supply
(JG616A)
Physical characteristics
Services
Dimensions
1.61(w) x 16.14(d) x 4.02(h) in (4.1 x 41.0 x 10.21
cm)
Weight
9.26 lb (4.2 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP sales
office.
DA - 14585 Worldwide QuickSpecs — Version 10 — 12.12.2014
Page 25
QuickSpecs
HP FlexFabric 11900 Switch Series
Accessory Product Details
HP FlexFabric 11900
2400W DC Power Supply
(JG617A)
Physical characteristics
Services
Dimensions
1.61(w) x 16.14(d) x 4.02(h) in (4.1 x 41.0 x 10.2
cm)
Weight
5.29 lb (2.4 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP sales
office.
HP FlexFabric 11908-V Switch Chassis (JG608A)
HP FlexFabric 11908
1.92Tbps Type D Fabric
Module (JG610A)
HP FlexFabric 11908-V
Spare Fan Assembly
(JG618A)
Physical characteristics
Services
16.77(w) x 11.73(d) x 1.57(h) in (42.6 x 29.79 x
3.99 cm)
Weight
9.7 lb (4.4 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP sales
office.
Physical characteristics
Dimensions
Services
Dimensions
17.32(w) x 25.75(d) x 3.15(h) in (43.99 x 65.41 x
8.0 cm)
Weight
8.29 lb (3.76 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP sales
office.
DA - 14585 Worldwide QuickSpecs — Version 10 — 12.12.2014
Page 26
QuickSpecs
HP FlexFabric 11900 Switch Series
Summary of Changes
Date
12-Dec-2014
18-Aug-2014
Version History
Action
From Version 9 to 10 Removed
From Version 8 to 9 Added
Changed
Description of Change:
Deleted SKU JG325A
New accessory: JG918A
Product overview updated
Configuration menu updated
02-Jul-2014
10-Jun-2014
31-Mar-2014
14-Oct-2014
From Version 7 to 8
From Version 6 to 7
From Version 4 to 6
From Version 3 to 4
Changed
Added
Changed
Added
30-Sept-2014
From Version 2 to 3 Added
12-Jul-2014
From Version 1 to 2 Changed
Technical Specifications updated
Minor change on Overview section.
Added a new accessory: JG372A
Transceivers were revised.
Added a new Transceiver in two locations in the Configuration
section.
HP 10500/11900/7500 20Gbps VPN FW Mod was added to
Modules.
Made minor changes to the Configuration section.
To learn more, visit: www.hp.com/networking
© Copyright 2011-2014 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without
notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such
products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical
or editorial errors or omissions contained herein.
4AA4-6972ENW, Created June 2013; Updated September 2013, Rev. 1
DA - 14585 Worldwide QuickSpecs — Version 10 — 12.12.2014
Page 27
Download PDF
Similar pages