U7xi U7xe U5x U3xe U3x R7xi R7xe R5x R3xe R3x H7xi H7xe H5x

U7xi
U7xe
U5x
U3xe
U3x
R7xi
R7xe
R5x
R3xe
R3x
H7xi
H7xe
H5x
H3xe
H3x
2
IMPORTANT PRECAUTIONS
SAVE THESE INSTRUCTIONS
•When using Matrix Cycles, basic precautions should always be followed, including the following: Read all instructions before using this equipment. It is
the responsibility of the owner to ensure that all users of this equipment are adequately informed of all warnings and precautions.
•This equipment is intended for commercial use. To ensure your safety and protect the equipment, read all instructions before operating.
DANGER!
TO REDUCE THE RISK OF ELECTRICAL SHOCK:
•Always unplug the equipment from the electrical outlet, before cleaning, performing maintenance and putting on or taking off parts.
WARNING!
TO REDUCE THE RISK OF BURNS, FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS:
•Use this exercise cycle for its intended purpose as
described in this manual. Do not use attachments that
have not been recommended by the manufacturer.
•Never operate the exercise cycle if it is not working properly,
or if it has been damaged. Contact Customer Tech Support
or the authorized dealers for examination and repair.
•Do not use the exercise cycle without proper footwear.
NEVER operate the exercise cycle with bare feet.
•Do not wear any clothing that might catch on
any moving parts of this exercise cycle.
•Keep hands and feet clear at all times from moving parts
to avoid injury. Never turn the pedal cranks by hand.
•Do not dismount the exercise cycle until
the pedals are at a complete STOP.
•Do not attempt to ride the exercise
cycle in a standing position.
•Do not insert any object, hands or feet into any openings,
or expose hands, arms or feet to the drive mechanism
or other potentially moving part of the exercise cycle.
•Do not use any equipment that is damaged or has worn
or broken parts. Use only replacement parts supplied
by Customer Tech Support or the authorized dealers.
•Do not operate where aerosol (spray) products are
being used or when oxygen is being administered.
•Close supervision is necessary when used near children.
•This equipment is not intended for use by persons with
reduced physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have been
given supervision or instruction concerning use of the
equipment by a person responsible for their safety.
•Ensure that adjustment levers (seat and handlebar
fore-and-aft) are properly secured and do not
interfere with range of motion during exercise.
•Incorrect or excessive exercise may result in serious
injury or death. If you experience any kind of pain,
including but not limited to chest pains, nausea, dizziness,
or shortness of breath, stop exercising immediately
and consult your physician before continuing.
•Do not jump on the unit.
•At no time should more than one person
be on unit while in operation.
•This unit should not be used by persons weighing more
than specified in the OWNER’S MANUAL SPECIFICATIONS
SECTION. Failure to comply will void the warranty.
•Keep power cord away from heated surfaces. Do not carry
this unit by its supply cord or use the cord as a handle.
•Disconnect all power before servicing or moving
the equipment. To clean, wipe surfaces down
with soap and slightly damp cloth only; never
use solvents. (See MAINTENANCE)
•At NO time should pets or children under the
age of 14 be closer to the unit than 10 feet.
•At NO time should children under the age of 14 use the unit.
•Children over the age of 14 should not use
the unit without adult supervision.
•Never operate the unit if it has a damaged cord or
plug, if it is not working properly, if it has been dropped
or damaged, or immersed in water. Return the unit
to a service center for examination and repair.
•To disconnect, turn all controls to the off
position, then remove plug from outlet.
•Do not remove the console covers unless instructed
by Customer Tech Support. Service should only
be done by an authorized service technician.
•Heart rate monitoring systems may be inaccurate.
•Do not use other attachments that are not recommended
by the manufacturer. Attachments may cause injury.
•Use the unit only as described in the
unit guide and owner’s manual.
CAUTION!
CONSULT A PHYSICIAN BEFORE USING THIS EQUIPMENT. READ OWNER’S MANUAL BEFORE USE.
•It is essential that this equipment is used only indoors, in a climate controlled room. If this equipment has been exposed to colder temperatures or high moisture
climates, it is strongly recommended that the equipment is warmed up to room temperature and allowed time to dry out before first time use.
3
POWER REQUIREMENTS
DEDICATED CIRCUIT AND ELECTRICAL INFO
A “Dedicated Circuit” means that each outlet you plug into should
not have anything else running on that same circuit. The easiest
way to verify this is to locate the main circuit breaker box, and turn
off the breaker(s) one at a time. Once a breaker has been turned
off, the only thing that should not have power to it are the units
in question. No lamps, vending machines, fans, sound systems, or
any other item should lose power when you perform this test.
for power. These cycles can be daisy-chained
together with up to 4 units per 15 A circuit. This
outlet should be a NEMA 6-20R and have the
same configuration as the plug. No adapter
should be used with this product. Matrix
daisy-chain cord adapters are sold separately.
110 NEMA 5-15P
PLUG
Non-looped (isolated) neutral/grounding means that each circuit
must have an individual neutral/ground connection coming from
it, and terminating at an approved earth ground. You cannot
“jumper” a single neutral/ground from one circuit to the next.
ELECTRICAL REQUIREMENTS
For your safety and to ensure good unit performance, the ground
on this circuit must be non-looped (isolated). Please refer to
NEC article 210-21 and 210-23. Any alterations to the standard
power cord provided could void all warranties of this product.
The 3x, 3xe, 5x, 7xe and 7xi cycles are designed to be self-powered
and do not require an external power supply source to operate.
Without an external power supply, the console’s start-up time
may be delayed. Add-on TV’s and other console accessories
will increase the time needed for start-up. An external power
supply will ensure power is provided to the console at all times
and is recommended when add-on accessories are used.
For units with an integrated TV (like the 3xe, 7xe and 7xi), the
TV power requirements are included in the unit. An RG6 quad
shield coaxial cable with ‘F Type’ compression fittings on each
end will need to be connected to the cardio unit and the video
source. Additional power requirements are not needed for
the add-on digital TV (3x and 5x). For units with an add-on
PCTV (3x and 5x), the TV power requirements are separate.
NOTE: All units with Virtual Active™ must be powered.
110 V UNITS
All Matrix 110 V cycles require the use of a 100-125 V, 60 Hz and a 15
A “Dedicated Circuit”, with a non-looped (isolated) neutral/ground
for power. These cycles can be daisy-chained together with up to 4
units per 15 A circuit. This outlet should be a NEMA 5-15R and have
the same configuration as the plug. No adapter should be used with
this product. Matrix daisy-chain cord adapters are sold separately.
220 V UNITS
All Matrix 220 V cycles require the use of a 216-250 V, 50 Hz and a 15
A “Dedicated Circuit”, with a non-looped (isolated) neutral/ground
4
220 NEMA 6-20P
PLUG
North American
power cord plugs
shown. Depending
on your country, the
plug type may vary.
GROUNDING INSTRUCTIONS
The unit must be grounded if connected to a
power supply source. If it should malfunction
or breakdown, grounding provides a path of
least resistance for electric current to reduce
the risk of electric shock. The unit is equipped
with a cord having an equipment-grounding
conductor and a grounding plug. The plug must
be plugged into an appropriate outlet that is
properly installed and grounded in accordance
with all local codes and ordinances. If the user
does not follow these grounding instructions,
the user could void the Matrix limited warranty.
ADDITIONAL ELECTRICAL INFO
In addition to the dedicated circuit requirement, the proper
gauge wire must be used from the circuit breaker box, to each
outlet that will have the maximum number of units running
off of it. If the distance from the circuit breaker box to each
outlet, is 100 ft (30.5 m) or less, then 12 gauge wire should be
used. For distances greater than 100 ft (30.5 m) from the circuit
breaker box to the outlet, a 10 gauge wire should be used.
RG6 coaxial cable with ‘F Type’ compression
fittings will need to be connected between the
video source and each add-on PCTV unit.
ADD-ON DIGITAL TV (3X AND 5X)
Additional power requirements are not needed
for the add-on digital TV. An RG6 coaxial
cable with ‘F Type’ compression fittings will
need to be connected between the video
source and each add-on digital TV unit.
WARNING!
•Connect this exercise product to a
properly grounded outlet only.
•Never operate product with a damaged cord
or plug even if it is working properly. Never
operate any product if it appears damaged, or
has been immersed in water. Contact Customer
Tech Support for replacement or repair.
Failure to follow these specifications
can cause damage to your product
and can void the warranty:
•All video and power outlets must be functional
the day of delivery / assembly of the product.
The client is responsible for any additional
installation charges associated with return visits.
•Electrical supply may fluctuate in your
area. To ensure stable performance of the
product, use the proper gauge wire.
ENERGY SAVING / LOW-POWER MODE
All units are configured with the ability to enter into an energy
saving / low-power mode when the unit has not been in use
for a specified period of time. Additional time may be required
to fully reactivate this unit once it has entered the low-power
mode. This energy saving feature may be enabled or disabled
from within the ‘Manager Mode’ or ‘Engineering Mode.’
ADD-ON PCTV (3X AND 5X)
A 15 A or 20 A “Dedicated Circuit” with a non-looped (isolated)
neutral/ground is required. Each PCTV requires at least 1.2 A of
current. No more than 12 PCTVs should be used for each 15 A
circuit and no more than 16 PCTVs should be used for each 20
A circuit. The power outlet should have the same configuration
as the plug. No adapter should be used with this product. An
DANGER!
Improper connection of the equipmentgrounding conductor can result in a risk of
electric shock. Check with a qualified electrician
or serviceman if you are in doubt as to whether
the product is properly grounded. Do not
modify the plug provided with the product.
If it will not fit the outlet, have a proper
outlet installed by a qualified electrician.
ASSEMBLY
UNPACKING
Unpack the equipment where you will be using it. Place the carton
on a level flat surface. It is recommended that you place a protective
covering on your floor. Never open box when it is on its side.
Upright Cycles
Page
8
Recumbent Cycles
Page
12
Hybrid Cycles
Page
17
IMPORTANT NOTES
During each assembly step, ensure that ALL nuts and
bolts are in place and partially threaded.
Several parts have been pre-lubricated to aid in assembly
and usage. Please do not wipe this off. If you have difficulty,
a light application of lithium grease is recommended.
WARNING!
There are several areas during the assembly process that special
attention must be paid. It is very important to follow the assembly
instructions correctly and to make sure all parts are firmly tightened. If
the assembly instructions are not followed correctly, the equipment could
have parts that are not tightened and will seem loose and may cause
irritating noises. To prevent damage to the equipment, the assembly
instructions must be reviewed and corrective actions should be taken.
NEED HELP?
If you have questions or if there are any missing parts, contact Customer
Tech Support. Contact information is located on the information card.
5
U7xi
U7xe
U5x
U3xe
U3x
PULSE GRIPS
WATER BOTTLE POCKETS
HANDLEBARS
SEAT
CONSOLE
ACCESSORY TRAY
CONSOLE MAST
CRANK
SEAT ADJUSTMENT LEVER
PEDALS
STEP PLATE
REAR FRAME HANDLE
REAR FRAME COVER
REAR STABILIZER TUBE
MAIN FRAME
6
RESISTANCE TOGGLES
FRONT SHROUD COVER
FRONT STABILIZER TUBE
TRANSPORT WHEELS
POWER CORD SOCKET
Upright Cycle Assembly
1
Yellow Hardware Bag
A
B
Description
Bolt
Flat Washer
Qty
8
8
U7xi
U7xe
U5x
U3xe
U3x
TOOLS REQUIRED:
FF 4 mm Allen Wrench
FF 6 mm Allen Wrench
FF 8 mm Allen Wrench
FF Flat Wrench (15mm/17mm 325L)
FF Phillips Screwdriver
PARTS INCLUDED:
FF 1 Main Frame
FF 1 Rear Stabilizer Tube
FF 1 Front Stabilizer Tube
FF 1 Rear Frame Handle
A
FF 1 Rear Frame Cover
FF 1 Console Mast
B
FF 1 Seat Back
FF 1 Seat Base
FF 1 Arm Rest Handlebars
FF 1 Front Shroud Cover
FF 1 Pulse Grip Handlebars
FF 2 Pedals
FF 1 Hardware Kit
FF 1 Power Cord
(included with 3xe, 7xe, and 7xi console)
Console sold separately
7
2
U7xi
U7xe
U5x
U3xe
U3x
D
C
D
E
F
Description
Bolt (black)
Screw
Bolt (chrome)
Tooth Washer
3
Qty
2
2
4
4
Green Hardware Bag
G
Description
Screw
Qty
4
G
E
C
8
Black / Red Hardware Bags
G
F
4
White / Green Hardware Bags
G
H
Description
Screw
Bolt
5
Qty
4
4
Purple Hardware Bag
A
I
Description
Bolt
Spring Washer
Qty
4
4
ASSEMBLY COMPLETE!
U7xi
U7xe
U5x
U3xe
U3x
Pre-Installed Hardware
J
Description
Bolt
Qty
4
H
G
I
A
J
9
R7xi
R7xe
R5x
R3xe
R3x
SEAT BACK
CONSOLE
SEAT BASE
CONSOLE HANDLEBARS
SEAT FRAME
SEAT RAMP
PULSE GRIPS / RESISTANCE TOGGLES
WATER BOTTLE POCKETS
CRANK
SEAT ADJUSTMENT LEVER
PEDALS
REAR FRAME HANDLE
REAR STABILIZER TUBE
REAR FRAME COVER
MAIN FRAME
10
CONSOLE MAST
FRONT SHROUD COVER
FRONT STABILIZER TUBE
TRANSPORT WHEELS
POWER CORD SOCKET
Recumbent Cycle Assembly
1
Yellow Hardware Bag
A
B
Description
Bolt
Flat Washer
Qty
8
8
R7xi
R7xe
R5x
R3xe
R3x
TOOLS REQUIRED:
FF 4 mm Allen Wrench
FF 6 mm Allen Wrench
FF Flat Wrench (15mm/17mm 325L)
FF Phillips Screwdriver
PARTS INCLUDED:
FF 1 Main Frame
FF 1 Rear Stabilizer Tube
FF 1 Front Stabilizer Tube
FF 1 Rear Frame Handle
FF 1 Rear Frame Cover
FF 1 Console Mast
A
FF 1 Console Handlebars
FF 1 Front Shroud Cover
B
FF 1 Seat Frame
FF 2 Water Bottle Pockets
FF 1 Seat Base
FF 1 Seat Back
FF 2 Pedals
FF 1 Hardware Kit
FF 1 Power Cord
(included with 3xe, 7xe, and 7xi console)
Console sold separately
11
2
R7xi
R7xe
R5x
R3xe
R3x
D
Black / Red Hardware Bags
C
D
E
F
Description
Bolt (black)
Screw
Bolt (chrome)
Tooth Washer
3
Qty
2
2
4
4
E
White / Green Hardware Bags
G
D
Description
Bolt
Screw
Qty
4
4
E
D
C
F
12
Pink / Blue Hardware Bags
4
D
H
I
Description
Screw
Bolt
Spring Washer
5
Qty
4
4
4
Purple / Orange Hardware Bag
J
K
L
M
Description
Bolt
Spring Washer
Wavy Washer
Bolt
Qty
4
4
4
2
R7xi
R7xe
R5x
R3xe
R3x
H
I
D
M
L
K
J
13
6
Pre-Installed Hardware
N
Description
Bolt
Qty
4
ASSEMBLY COMPLETE!
R7xi
R7xe
R5x
R3xe
R3x
N
14
SEAT BACK
ARM REST HANDLEBARS
SEAT FRAME
SEAT BASE
PULSE GRIPS / RESISTANCE TOGGLES
CONSOLE
PULSE GRIP HANDLEBARS
CONSOLE MAST
SEAT RAMP
CRANK
MAIN FRAME
PEDALS
REAR FRAME HANDLE
REAR FRAME COVER
REAR STABILIZER TUBE
SEAT ADJUSTMENT LEVER
H7xi
H7xe
H5x
H3xe
H3x
FRONT SHROUD COVER
FRONT STABILIZER TUBE
TRANSPORT WHEELS
POWER CORD SOCKET
15
Hybrid Cycle Assembly
H7xi
H7xe
H5x
H3xe
H3x
1
Yellow Hardware Bag
A
B
Description
Bolt
Flat Washer
Qty
8
8
TOOLS REQUIRED:
FF 4 mm Allen Wrench
FF 6 mm Allen Wrench
FF 8 mm Allen Wrench
FF Flat Wrench (15mm/17mm 325L)
FF Phillips Screwdriver
PARTS INCLUDED:
FF 1 Main Frame
FF 1 Rear Stabilizer Tube
FF 1 Front Stabilizer Tube
FF 1 Rear Frame Handle
FF 1 Rear Frame Cover
FF 1 Console Mast
A
FF 1 Seat Back
FF 1 Seat Base
FF 1 Arm Rest Handlebars
FF 1 Front Shroud Cover
FF 1 Pulse Grip Handlebars
FF 2 Pedals
FF 1 Hardware Kit
FF 1 Power Cord
(included with 3xe, 7xe, and 7xi console)
Console sold separately
16
B
Black / Red Hardware Bags
2
C
D
E
F
Description
Bolt (black)
Screw
Bolt (chrome)
Tooth Washer
3
Qty
2
2
4
4
E
Green / Blue Hardware Bag
G
H
I
Description
Screw
Bolt
Heavy Washer
Qty
4
2
2
H7xi
H7xe
H5x
H3xe
H3x
I
H
D
G
C
F
17
4
H7xi
H7xe
H5x
H3xe
H3x
Purple / Orange Hardware Bags
J
K
L
M
Description
Bolt
Spring Washer
Wavy Washer
Bolt
Qty
4
4
4
2
5
Pre-Installed Hardware
N
Description
Bolt
ASSEMBLY COMPLETE!
Qty
4
N
M
L
K
J
18
BEFORE YOU BEGIN
LOCATION OF THE UNIT
Place the equipment on a level and stable surface away from direct sunlight.
The intense UV light can cause discoloration on the plastics. Locate your
equipment in an area with cool temperatures and low humidity. Please
leave a clear zone on both sides of the equipment that is at least 24”
(600 mm). This zone must be clear of any obstruction and provide the
user a clear exit path from the machine. Do not place the equipment in
any area that will block any vent or air openings. The equipment should
not be located in a garage, covered patio, near water or outdoors.
POWER
If the equipment is powered by a power supply, the power must be plugged
into the power jack, which is located in the front of the equipment near the
stabilizer tube. Some equipment has a power switch, located next to the power
jack. Make sure it is in the ON position. Unplug cord when not in use.
WARNING!
Never operate equipment if it has a damaged cord or plug, if it is not working properly, if it has been
damaged, or immersed in water. Contact Customer Tech Support for examination and repair.
LEVELING THE EQUIPMENT
HYBRID SEAT HEIGHT
The equipment should be level for optimum use. Once you have
placed the equipment where you intend to use it, raise or lower one
or both of the adjustable levelers located on the bottom of the frame.
Use 6mm hex key through the access hole (shown below).
To adjust the seat height on the Hybrid Cycle, pull the orange lever under the seat and
lower the seat to the lowest position, stand over the seat and grab the orange lever. Pull
the lever and lift until the seat base makes contact with your pelvic bone.
A carpenter’s level is recommended.
NOTE: There are only two levelers on the equipment.
WARNING!
Our equipment is heavy, use care and additional help if necessary when
moving. Failure to follow these instructions could result in injury.
RECUMBENT SEAT HEIGHT
To adjust the seat height on the Recumbent Cycle, locate the orange lever under the seat
before you mount the Cycle. Place your right hand on the orange adjustment handle
under the seat. Place feet on the ground while seated and slide forward if needed. Place
feet on pedals, gently lift lever under the seat. Using legs, slowly push and slide the seat
up or down to desired position. Release lever and allow to lock into place.
UPRIGHT SEAT HEIGHT
To raise the seat height on the Upright Cycle, pull the seat upward. To lower the seat,
locate the orange adjustment lever under the seat and pull the lever up to slide the seat
down. Release lever and allow to lock into place.
FREE AREA
The seat height adjusts from level 1 to 23. Do not raise the seat past level 23.
0.6 m
(2 ft)
0.6 m
(2 ft)
0.6 m
(2 ft)
19
PROPER USAGE
To determine proper seat position, sit on the seat and position
the ball of your foot on the center of the pedal. Your knee should
bend slightly at the furthest pedal position. You should be able
to pedal without locking your knees or shifting your weight
from side to side. Adjust pedal straps to desired tightness.
USING THE HEART RATE FUNCTION
The heart rate function on this product is not a medical device. While heart rate grips
can provide a relative estimation of your actual heart rate, they should not be relied
on when accurate readings are necessary. Some people, including those in a cardiac
rehab program, may benefit from using an alternate heart rate monitoring system
like a chest or wrist strap. Various factors, including movement of the user, may affect
the accuracy of your heart rate reading. The heart rate reading is intended only as an
exercise aid in determining heart rate trends in general. Please consult your physician.
PULSE GRIPS
Place the palm of your hands directly on the grip pulse handlebars. Both hands must grip
the bars for your heart rate to register. It takes 5 consecutive heart beats (15-20 seconds)
for your heart rate to register. When gripping the pulse handlebars, do not grip tightly.
Holding the grips tightly may elevate your blood pressure. Keep a loose, cupping hold.
You may experience an erratic readout if consistently holding the grip pulse handlebars.
Make sure to clean the pulse sensors to ensure proper contact can be maintained.
WIRELESS HEART RATE RECEIVER
Backside of chest strap
Apply moisture here
When used in conjunction with a wireless chest transmitter, your heart rate
can be transmitted wirelessly to the unit and displayed on the console.
Prior to wearing the wireless chest transmitter on your chest, moisten the two rubber
electrodes with water. Center the chest strap just below the breast or pectoral muscles,
directly over your sternum, with the logo facing out. NOTE: The chest strap must be tight and
properly placed to receive an accurate and consistent readout. If the chest strap is too loose,
or positioned improperly, you may receive an erratic or inconsistent heart rate readout.
WARNING!
Heart rate monitoring systems may be inaccurate. Over exercising may result in
serious injury or death. If you feel faint, stop exercising immediately.
20
MAINTENANCE
1. Any and all part removal or replacement must be
performed by a qualified service technician.
2. DO NOT use any equipment that is damaged and or has worn or broken parts.
Use only replacement parts supplied by your country’s local MATRIX dealer.
3. MAINTAIN LABELS AND NAMEPLATES: Do not remove labels for
any reason. They contain important information. If unreadable or
missing, contact your MATRIX dealer for a replacement.
4. MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to
smooth operating equipment as well as keeping your liability to a
minimum. Equipment needs to be inspected at regular intervals.
5. Ensure that any person(s) making adjustments or performing maintenance
or repair of any kind is qualified to do so. MATRIX dealers will provide
service and maintenance training at our corporate facility upon request.
WARNING
To remove power from the exercise cycle, the power cord
must be disconnected from the wall outlet.
MAINTENANCE SCHEDULE
ACTION
FREQUENCY
Unplug the unit. Clean entire machine using water and a mild soap or
other Matrix approved solution (cleaning agents should be alcohol and
ammonia free).
DAILY
Inspect the power cord. If the power cord is damaged, contact Customer
Tech Support.
DAILY
Make sure the power cord is not underneath the unit or in any other area
where it can become pinched or cut during storage or use.
DAILY
Clean underneath the cycle, following these steps:
• Turn off the cycle.
• Move the cycle to a remote location.
• Wipe or vacuum any dust particles or other objects that may have
accumulated underneath the cycle.
• Return the cycle to its previous position.
WEEKLY
Inspect all assembly bolts and pedals on the machine for proper
tightness.
MONTHLY
Clean any debris off of the seat guide rail.
MONTHLY
For 7xe consoles, enter service mode and select ‘test’. Select ‘touch
calibration’ and then select ‘start’. Follow the on-screen prompts and touch
the screen where indicated.
QUARTERLY
21
PRODUCT SPECIFICATIONS
U7xi Upright Cycle
U7xe Upright Cycle
U5x Upright Cycle
U3xe Upright Cycle
U3x Upright Cycle
Max User Weight
182 kg / 400 lbs
Assembled Weight
87.8 kg / 193.5 lbs
87.8 kg / 193.5 lbs
87.4 kg / 192.6 lbs
87.8 kg / 193.5 lbs
86.3 kg / 190.2 lbs
Shipping Weight
102 kg / 224.9 lbs
102 kg / 224.9 lbs
99.8 kg / 220 lbs
102 kg / 224.9 lbs
99.7 kg / 219.7 lbs
Assembled Dimensions
(L x W x H)*
130.7 x 65.4 x 153.7 cm /
51.5” x 25.7” x 60.5”
130.7 x 65.4 x 153.7 cm /
51.5” x 25.7” x 60.5”
130.7 x 65.4 x 153.7 cm /
51.5” x 25.7” x 60.5”
130.7 x 65.4 x 153.7 cm /
51.5” x 25.7” x 60.5”
130.7 x 65.4 x 153.7 cm /
51.5” x 25.7” x 60.5”
R7xi Recumbent Cycle
R7xe Recumbent Cycle
R5x Recumbent Cycle
R3xe Upright Cycle
R3x Recumbent Cycle
Max User Weight
182 kg / 400 lbs
Assembled Weight
89 kg / 196.3 lbs
89 kg / 196.3 lbs
88.6 kg / 195.3 lbs
89 kg / 196.3 lbs
87.5 kg / 192.9 lbs
Shipping Weight
101.3 kg / 223.5 lbs
101.3 kg / 223.5 lbs
100.3 kg / 221 lbs
101.3 kg / 223.5 lbs
99.7 kg / 219 lbs
Assembled Dimensions
(L x W x H)*
150.3 x 65.4 x 140 cm /
59.2” x 25.7” x 55.1”
150.3 x 65.4 x 140 cm /
59.2” x 25.7” x 55.1”
150.3 x 65.4 x 140 cm /
59.2” x 25.7” x 55.1”
130.7 x 65.4 x 153.7 cm /
51.5” x 25.7” x 60.5”
150.3 x 65.4 x 140 cm /
59.2” x 25.7” x 55.1”
H7xi Hybrid Cycle
H7xe Hybrid Cycle
H5x Hybrid Cycle
H3xe Upright Cycle
H3x Hybrid Cycle
Max User Weight
182 kg / 400 lbs
Assembled Weight
100 kg / 220 lbs
100 kg / 220 lbs
97.1 kg / 214 lbs
100 kg / 220 lbs
96.2 kg / 212 lbs
Shipping Weight
102 kg / 224.9 lbs
102 kg / 224.9 lbs
101 kg / 222 lbs
102 kg / 224.9 lbs
99.7 kg / 219 lbs
Assembled Dimensions
(L x W x H)*
146.8 x 65.4 x 156.8 cm /
57.8” x 25.7” x 61.7”
146.8 x 65.4 x 156.8 cm /
57.8” x 25.7” x 61.7”
146.8 x 65.4 x 156.8 cm /
57.8” x 25.7” x 61.7”
130.7 x 65.4 x 153.7 cm /
51.5” x 25.7” x 60.5”
146.8 x 65.4 x 156.8 cm /
57.8” x 25.7” x 61.7”
* Ensure a minimum clearance width of 0.6 meters (24”) for access to and passage around MATRIX equipment.
Please note, 0.91 meters (36”) is the ADA recommended clearance width for individuals in wheelchairs.
22
Cycles Frame
© 2016 Johnson Health Tech
Part # XXXXXXXXXX
Rev 1.0 A
Download PDF
Similar pages