HP 5400R zl2 Switch Series data sheet

Data sheet
HP 5400R zl2 Switch Series
Key features
•Advanced access layer, distribution, and core optimized for SDN, security and resiliency
•Purpose built 6th Gen HP Networking ASIC with Integrated L2 to L4 intelligent edge feature set
•Enterprise-class resiliency with hitless fail-over, power supply and management module redundancy
•HP Smart Rate multi-gigabit ports with MACsec ready hardware
•Scalable 10/100/1000, 10GbE, and 40GbE connectivity with full PoE+ provisioning
Product overview
The HP 5400R zl2 Switch Series consists of advanced intelligent switches with resiliency and
redundant management in the HP modular chassis product line, which includes 6-slot and
12-slot chassis and associated modules and bundles. The foundation for the switch series
is a purpose-built, programmable 6th Generation HP Networking ASIC that allows the most
demanding networking features, such as Quality of Service (QoS), advanced SDN functionality,
and MACsec ready hardware. With HP Smart Rate multi-gigabit, gigabit, 10 gigabit and 40 gigabit
Ethernet interfaces; choice of PoE+ and non-PoE, integrated Layer 3 features, and HP AllianceOne
solutions, the 5400R zl2 switch series offers excellent investment protection, flexibility, and
scalability, as well as ease of deployment, operation, and maintenance.
Features and benefits
Software-defined networking
•OpenFlow
supports OpenFlow 1.0 and 1.3 specifications to enable SDN by allowing separation of the data
(packet forwarding) and control (routing decision) paths
•NEW Fully flexible OpenFlow
creates custom OpenFlow pipelines (processing stages) on-demand to support new SDN
applications (requires v3 modules)
Data sheet | HP 5400R zl2 Switch Series
Unified Wired and Wireless
•HTTP redirect function
supports HP Intelligent Management Center (IMC) bring your own device (BYOD) solution
Quality of Service (QoS)
•Advanced classifier-based QoS
classifies traffic using multiple match criteria based on Layer 2, 3, and 4 information; applies
QoS policies such as setting priority level and rate limit to selected traffic on a per-port or per-VLAN basis
•Traffic prioritization
allows real-time traffic classification into eight priority levels mapped to eight queues
•Bandwidth shaping
––Port-based rate limiting
provides per-port ingress-/egress-enforced increased bandwidth
––Classifier-based rate limiting
uses an access control list (ACL) to enforce increased bandwidth for ingress traffic on each port
––Reduced bandwidth
provides per-port, per-queue egress-based reduced bandwidth
•Class of Service (CoS)
sets the IEEE 802.1p priority tag based on IP address, IP Type of Service (ToS), Layer 3 protocol,
TCP/UDP port number, source port, and DiffServ
Management
•Remote intelligent mirroring
mirrors selected ingress/egress traffic based on ACL, port, MAC address, or VLAN to a local or
remote HP 8200 zl, 6600, 6200 yl, 5400 zl, 5400R, 3500, or 3800 Switch located anywhere on
the network
•RMON, XRMON, and sFlow® v5
provide advanced monitoring and reporting capabilities for statistics, history, alarms, and
events
•IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
advertises and receives management information from adjacent devices on a network,
facilitating easy mapping by network management applications
•NEW Uni-Directional Link Detection (UDLD)
support HP UDLD and DLDP protocols to monitor a cable between two switches and shut down
the ports on both ends if the cable is broken
•Management simplicity
provides common software features and CLI implementation across all HP ProVision-based
switches (including the zl and yl switches)
•Command authorization
leverages RADIUS to link a custom list of CLI commands to an individual network
administrator’s login; an audit trail documents activity
•Friendly port names
allows assignment of descriptive names to ports
2
Data sheet | HP 5400R zl2 Switch Series
•Dual flash images
provides independent primary and secondary operating system files for backup while
upgrading
•Multiple configuration files
stores easily to the flash image
•Comware CLI
––Comware-compatible CLI
bridges the experience of HP Comware CLI users who are using the HP ProVision software CLI
––Display and fundamental Comware CLI commands
are embedded in the switch CLI as native commands; display output is formatted as on
Comware-based switches, and fundamental commands provide a Comware-familiar initial
switch setup
––Configuration Comware CLI commands
when Comware commands are entered, CLI help is elicited to formulate the correct ProVision
software CLI command
Connectivity
•IEEE 802.3az Energy Efficient Ethernet
lowers power consumption in periods of low link usage (supported on v2 zl 10/100/1000 and
10/100 modules)
•IEEE 802.3af Power over Ethernet (PoE)
provides up to 15.4 W per port to IEEE 802.3af-compliant PoE-powered devices such as IP
phones, wireless access points, and security cameras
•IEEE 802.3at Power over Ethernet Plus
provides up to 30 W per port, for up to 288 ports simultaneously, for PoE- and PoE+-powered
devices, such as video IP phones, IEEE 802.11n wireless access points, and advanced pan/
zoom/tilt security cameras
•Prestandard PoE support
detects and provides power to prestandard PoE devices
•High-density port connectivity
provides up to 12 interface module slots and up to 288 wire-speed 10/100/1000 PoE-enabled
ports or 96 10GbE ports per system
•Jumbo frames
on Gigabit Ethernet and 10-Gigabit Ethernet ports, jumbo frames allow high-performance
remote backup and disaster-recovery services
•Auto-MDIX
provides automatic adjustments for straight-through or crossover cables on all 10/100 and
10/100/1000 ports 3
Data sheet | HP 5400R zl2 Switch Series
•IPv6
––IPv6 host
enables switches to be managed in an IPv6 network
––Dual stack (IPv4 and IPv6)
transitions from IPv4 to IPv6, supporting connectivity for both protocols
––MLD snooping
forwards IPv6 multicast traffic to the appropriate interface
––IPv6 ACL/QoS
supports ACL and QoS for IPv6 network traffic
––IPv6 routing
supports static and OSPFv3 routing protocols
––6in4 tunneling
supports encapsulation of IPv6 traffic in IPv4 packets
––Security
provides RA guard, DHCPv6 protection, dynamic IPv6 lockdown
Performance
•High-speed, high-capacity architecture
2 Tbps crossbar switching fabric provides intra-module and inter-module switching with 785.7 million pps throughput on the purpose-built ProVision ASICs
•Selectable queue configurations
allows for increased performance by selecting the number of queues and associated memory
buffering that best meet the requirements of the network applications
Resiliency and high availability
•Virtual Router Redundancy Protocol (VRRP)
allows groups of two routers to dynamically back each other up to create highly available
routed environments for IPv4 and IPv6 networks
•Nonstop switching
improves network availability to better support critical applications such as unified
communication and mobility; interface and fabric modules continue switching traffic during
failover from active to standby management module
•Nonstop routing
enhances Layer 3 high availability; OSPFv2/v3 and VRRP will continue to operate and route
network traffic during failover from an active to a standby management module
•Redundant management and power
provide enhanced system availability and continuity of operations
•IEEE 802.1s Multiple Spanning Tree Protocol
provides high link availability in multiple VLAN environments by allowing multiple spanning
trees; encompasses IEEE 802.1D Spanning Tree Protocol and IEEE 802.1w Rapid Spanning Tree
Protocol
•IEEE 802.3ad Link Aggregation Control Protocol (LACP) and HP port trunking
support up to 144 trunks, each with up to eight links (ports) per trunk •Distributed trunking
enables loop-free and redundant network topology without using Spanning Tree Protocol;
allows a server or switch to connect to two switches using one logical trunk for redundancy
and load sharing
4
Data sheet | HP 5400R zl2 Switch Series
•Optional redundant power supply
provides uninterrupted power and allows hot-swapping of the redundant power supplies
when installed
•Hot-swappable modules
allows dissimilar modules, and power supplies in a redundant power supply configuration to
be added or swapped without interrupting the network
•Sparing simplicity
HP zl-common accessories (interface modules and power supplies)
•Uplink Failure Detection
provides active-standby network path redundancy for servers that are configured for active-standby NIC teaming
•Smart Link
provides easy-to-configure link redundancy of active and standby links
Layer 2 switching
•VLAN support and tagging
supports the IEEE 802.1Q standard and 2,048 VLANs simultaneously
•IEEE 802.1v protocol VLANs
isolate select non-IPv4 protocols automatically into their own VLANs
•GARP VLAN Registration Protocol
allows automatic learning and dynamic assignment of VLANs
•IEEE 802.1ad Q-in-Q
increases the scalability of an Ethernet network by providing a hierarchical structure; connects
multiple LANs on a high-speed campus or metro network
•MAC-based VLAN
provides granular control and security; uses RADIUS to map a MAC address/user to specific
VLANs (requires v2 or higher modules)
•Rapid Per-VLAN Spanning Tree (RPVST+)
allows each VLAN to build a separate spanning tree to improve link bandwidth usage; is
compatible with PVST+
•HP switch meshing
dynamically load balances across multiple active redundant links to increase available
aggregate bandwidth; allows concurrent Layer 3 routing with v2 or higher modules
Layer 3 services
•User Datagram Protocol (UDP) helper function
allows UDP broadcasts to be directed across router interfaces to specific IP unicast or subnet
broadcast addresses and prevents server spoofing for UDP services such as DHCP •Loopback interface address
defines an address in Routing Information Protocol (RIP) and Open Standard Path First (OSPF),
improving diagnostic capability
•Route maps
provide more control during route redistribution; allow filtering and altering of route metrics
•DHCP server
centralizes and reduces the cost of IPv4 address management
5
Data sheet | HP 5400R zl2 Switch Series
Layer 3 routing
•Static IP routing
provides manually configured routing for both IPv4 and IPv6 networks
•Routing Information Protocol (RIP)
provides RIPv1 and RIPv2 routing
•OSPF
provides OSPFv2 for IPv4 routing and OSPFv3 for IPv6 routing
•Policy-based routing
uses a classifier to select traffic that can be forwarded based on policy set by the network
administrator (requires v2 or higher modules)
•Border Gateway Protocol (BGP)
provides IPv4 Border Gateway Protocol routing, which is scalable, robust, and flexible
Security
•Access control lists (ACLs)
provide filtering based on the IP field, source/destination IP address/subnet, and source/
destination TCP/UDP port number on a per-VLAN or per-port basis
•Multiple user authentication methods
––IEEE 802.1X users per port
provides authentication of multiple IEEE 802.1X users per port
––Web-based authentication
authenticates from a Web browser for clients that do not support IEEE 802.1X supplicant
––MAC-based authentication
client is authenticated with the RADIUS server based on the client’s MAC address
––Concurrent IEEE 802.1X, Web, and MAC authentication schemes per port
switch port accepts up to 32 sessions of IEEE 802.1X, Web, and MAC authentications
•Virus throttling
detects traffic patterns typical of worm-type viruses and either throttles or entirely prevents
the virus from spreading across the routed VLANs or bridged interfaces without requiring
external appliances
•DHCP protection
blocks DHCP packets from unauthorized DHCP servers, preventing denial-of-service attacks
•Secure management access
delivers secure encryption of all access methods (CLI, GUI, or MIB) through SSHv2, SSL, and/or
SNMPv3 •Switch CPU protection
provides automatic protection against malicious network traffic trying to shut down the switch
•ICMP throttling
defeats ICMP denial-of-service attacks by enabling any switch port to automatically throttle
ICMP traffic
•Identity-driven ACL
enables implementation of a highly granular and flexible access security policy and VLAN
assignment specific to each authenticated network user
•STP BPDU port protection
blocks Bridge Protocol Data Units (BPDUs) on ports that do not require BPDUs, preventing
forged BPDU attacks
6
Data sheet | HP 5400R zl2 Switch Series
•Dynamic IP lockdown
works with DHCP protection to block traffic from unauthorized hosts, preventing IP source
address spoofing
•Dynamic ARP protection
blocks ARP broadcasts from unauthorized hosts, preventing eavesdropping or theft of
network data
•STP root guard
protects the root bridge from malicious attacks or configuration mistakes
•Detection of malicious attacks
monitors 10 types of network traffic and sends a warning when an anomaly that potentially
can be caused by malicious attacks is detected
•Port security
allows access only to specified MAC addresses, which can be learned or specified by the
administrator
•MAC address lockout
prevents particular configured MAC addresses from connecting to the network
•Source-port filtering
allows only specified ports to communicate with each other
•RADIUS/TACACS+
eases switch management security administration by using a password authentication server
•Secure Shell
encrypts all transmitted data for secure remote CLI access over IP networks
•Secure Sockets Layer (SSL)
encrypts all HTTP traffic, allowing secure access to the browser-based management GUI in the switch •Secure FTP
allows secure file transfer to and from the switch; protects against unwanted file downloads or
unauthorized copying of a switch configuration file
•Management Interface Wizard
helps secure management interfaces such as SNMP, telnet, SSH, SSL, Web, and USB at the
desired level
•Switch management logon security
helps secure switch CLI logon by optionally requiring either RADIUS or TACACS+ authentication
•Security banner
displays a customized security policy when users log in to the switch
•NEW IEEE 802.1AE MACsec
provides security on a link between two switch ports (1 Gbps or 10 Gbps) using standard
encryption and authentication. MACsec software support not yet available for modules with
Smart Rate ports (requires v3 modules)
7
Data sheet | HP 5400R zl2 Switch Series
Convergence
•IP multicast routing
includes PIM Sparse and Dense modes to route IP multicast traffic
•IP multicast snooping (data-driven IGMP)
prevents flooding of IP multicast traffic
•LLDP-MED (Media Endpoint Discovery)
defines a standard extension of LLDP that stores values for parameters such as QoS and VLAN
to automatically configure network devices such as IP phones
•PoE allocations
supports multiple methods (automatic, IEEE 802.3af class, LLDP-MED, or user-specified) to
allocate PoE power for more efficient energy savings
•Auto VLAN configuration for voice
––RADIUS VLAN
uses a standard RADIUS attribute and LLDP-MED to automatically configure a VLAN for IP phones
––CDPv2
uses CDPv2 to configure legacy IP phones
•Local MAC Authentication
assigns attributes such as VLAN and QoS using locally configured profile that can be a list of
MAC prefixes
Warranty and support
•Limited Lifetime Warranty 2.0
advance hardware replacement with next-business-day delivery (available in most countries).
See hp.com/networking/warrantysummary for duration details
•Electronic and telephone support (for Limited Lifetime Warranty 2.0)
limited 24x7 telephone support is available from HP for the first 3 years; limited electronic
and business hours telephone support is available from HP for the entire warranty period;
to reach our support centers, refer to hp.com/networking/contact-support; for details on
the duration of support provided with your product purchase, refer to hp.com/networking/
warrantysummary
•Software releases
to find software for your product, refer to hp.com/networking/support; for details on the
software releases available with your product purchase, refer to hp.com/networking/
warrantysummary
8
Data sheet | HP 5400R zl2 Switch Series
HP 5400R zl2 Switch Series
Specifications
HP 5406R zl2 Switch (J9821A)
HP 5412R zl2 Switch (J9822A)
HP 5406R-44G-PoE+/2SFP+ (No PSU)
v2 zl2 Switch (J9823A)
Included accessories
1 HP 5400R zl2 Management Module (J9827A)
1 HP 5406R zl2 Switch Fan Tray (J9831A)
1 HP 5400R zl2 Management Module (J9827A)
1 HP 5412R zl2 Switch Fan Tray (J9832A)
1 HP 5400R zl2 Management Module
(J9827A)
1 HP 5406R zl2 Switch Fan Tray (J9831A)
1 HP 24-port Gig-T PoE+ v2 zl Module
(J9534A)
1 HP 20-port Gig-T PoE+/2-port 10GbE
SFP+ v2 zl Module (J9536A)
I/O ports and slots
6 open module slots
Supports a maximum of 144 autosensing
10/100/1000 ports or 144 SFP ports or 48 SFP+ ports or 48 HP Smart Rate Multi-Gigabit or 12 40GbE ports, or a
combination
12 open module slots
Supports a maximum of 288 autosensing
10/100/1000 ports or 288 SFP ports or 96 SFP+ ports or 96 HP Smart Rate Multi-Gigabit or 24 40GbE ports, or a
combination
44 RJ-45 autosensing 10/100/1000 PoE+ ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE 802.3at PoE+); Media Type: Auto-MDIX; Duplex: 10BASE-T/
100BASE-TX: half or full; 1000BASE-T: full only
2 open 10GbE SFP+ transceiver slots
4 open module slots
Supports a maximum of 144 autosensing
10/100/1000 ports or 144 SFP ports
or 48 SFP+ ports or 48 HP Smart Rate
Multi-Gigabit or 12 40GbE ports, or a
combination
Power supplies
2 power supply slots
1 minimum power supply required (ordered separately)
4 power supply slots
2 minimum power supplies required (ordered separately)
2 power supply slots
1 minimum power supply required
(ordered separately)
Fan tray
Includes: 1 x J9831A
1 fan tray slot
Includes: 1 x J9832A
1 fan tray slot
Includes: 1 x J9831A
1 fan tray slot
17.5(w) x 17.75(d) x 6.9(h) in. (44.45 x 45.09 x 17.53 cm) (4U height)
24.5 lb (11.11 kg)
17.5(w) x 17.75(d) x 12.1(h) in. (44.45 x 45.09 x 30.73 cm) (7U height)
38.1 lb (17.28 kg)
17.5(w) x 17.75(d) x 6.9(h) in. (44.45 x 45.09 x 17.53 cm) (4U height)
28.11 lb (12.75 kg)
Dual ARM® Coretex A9 @ 1 GHz; Packet buffer size: 13.5 MB internal
ARM 11 @ 450 MHz; Packet buffer size: 18 MB internal
Dual ARM Coretex A9 @ 1 GHz; Packet buffer size: 13.5 MB internal
ARM 11 @ 550 MHz; Packet buffer
size: 18 MB internal
Dual ARM Coretex A9 @ 1 GHz; Packet buffer size: 13.5 MB internal
Freescale P2020 dual core @ 1.2 GHz, 16 MB flash, 1 GB SD Card, 4 GB DDR3 SODIMM
Dual ARM Coretex A9 @ 1 GHz; Packet buffer size: 13.5 MB internal
ARM 11 @ 450 MHz; Packet buffer size: 18 MB internal
Dual ARM Coretex A9 @ 1 GHz; Packet buffer size: 13.5 MB internal
ARM 11 @ 550 MHz; Packet buffer size: 18 MB internal
Dual ARM Coretex A9 @ 1 GHz; Packet buffer size: 13.5 MB internal
Freescale P2020 dual core @ 1.2 GHz, 16 MB flash, 1 GB SD Card, 4 GB DDR3 SODIMM
Dual ARM Coretex A9 @ 1 GHz; Packet buffer size: 13.5 MB internal
ARM 11 @ 450 MHz; Packet buffer size: 18 MB internal
Dual ARM Coretex A9 @ 1 GHz; Packet buffer size: 13.5 MB internal
ARM 11 @ 550 MHz; Packet buffer size: 18 MB internal
Dual ARM Coretex A9 @ 1 GHz; Packet buffer size: 13.5 MB internal
Freescale P2020 dual core @ 1.2 GHz, 16 MB flash, 1 GB SD Card, 4 GB DDR3 SODIMM
Physical characteristics
Dimensions
Weight
Memory and processor
v3 Gigabit Module
v2 Gigabit Module
v3 10G Module
v2 10G Module
v3 40G Module
Management Module
9
Data sheet | HP 5400R zl2 Switch Series
HP 5406R zl2 Switch (J9821A)
HP 5412R zl2 Switch (J9822A)
HP 5406R-44G-PoE+/2SFP+ (No PSU)
v2 zl2 Switch (J9823A)
Mounting and enclosure
Mounts in an EIA standard 19-inch telco rack or equipment cabinet (hardware included); Horizontal surface mounting only
Mounts in an EIA standard 19-inch telco rack or equipment cabinet (hardware included); Horizontal surface mounting only
Mounts in an EIA standard 19-inch telco rack or equipment cabinet (hardware included); Horizontal surface mounting only
Performance
1000 Mb Latency
10 Gbps Latency
40 Gbps Latency
Throughput
Routing/Switching capacity
Switch fabric speed
Routing table size
MAC address table size
IPv6 Ready Certified
< 2.8 µs (FIFO 64-byte packets)
< 1.8 µs (FIFO 64-byte packets)
< 1.5 µs (FIFO 64-byte packets)
Up to 571.4 Mpps
960 Gbps
1015 Gbps
10000 entries (IPv4), 5000 entries (IPv6)
64000 entries
IPv6 Ready Certified
< 2.8 µs (FIFO 64-byte packets)
< 1.8 µs (FIFO 64-byte packets)
< 1.5 µs (FIFO 64-byte packets)
Up to 1142.8 Mpps
1920 Gbps
2030 Gbps
10000 entries (IPv4), 5000 entries (IPv6)
64000 entries
IPv6 Ready Certified
< 2.8 µs (FIFO 64-byte packets)
< 1.8 µs (FIFO 64-byte packets)
< 1.5 µs (FIFO 64-byte packets)
Up to 571.4 Mpps
960 Gbps
1015 Gbps
10000 entries (IPv4), 5000 entries (IPv6)
64000 entries
32°F to 113°F (0°C to 45°C); 0°C to 40°C with J8177C transceiver installed, 0°C to 35°C with FIPS Opacity Shield installed
15% to 95% @ 113°F (45°C), noncondensing
-40°F to 158°F (-40°C to 70°C)
15% to 95% @ 149°F (65°C), noncondensing
Up to 10,000 ft (3 km)
Power: 44 dB, Pressure: 31.7 dB ISO 7779, ISO 9296
32°F to 113°F (0°C to 45°C); 0°C to 40°C with J8177C transceiver installed, 0°C to 35°C with FIPS Opacity Shield installed
15% to 95% @ 113°F (45°C), noncondensing
-40°F to 158°F (-40°C to 70°C)
15% to 95% @ 149°F (65°C), noncondensing
Up to 10,000 ft (3 km)
Power: 49 dB, Pressure: 35.7 dB ISO 7779, ISO 9296
32°F to 113°F (0°C to 45°C); 0°C to 40°C with J8177C transceiver installed, 0°C to
35°C with FIPS Opacity Shield installed
15% to 95% @ 113°F (45°C), noncondensing
-40°F to 158°F (-40°C to 70°C)
15% to 95% @ 149°F (65°C), noncondensing
Up to 10,000 ft (3 km)
Power: 44 dB, Pressure: 31.7 dB ISO 7779,
ISO 9296
50/60 Hz
Gold
Does not come with power supply. Two power supply slots are available; three different power supplies are available.
See power supply products for additional
specifications.
2450 BTU/hr (2584 kJ/hr), (max. non-PoE);
3700 BTU/hr (3903 kJ/hr), (max. using PoE)
100–127/200–240 VAC, rated
(depending on power supply chosen)
50/60 Hz
Gold
Does not come with power supply. Four power supply slots are available; three different power supplies are available.
See power supply products for additional
specifications.
4900 BTU/hr (5169 kJ/hr), (max. non-PoE);
7400 BTU/hr (7,807 kJ/hr), (max. using PoE)
100–127/200–240 VAC, rated
(depending on power supply chosen)
50/60 Hz
Gold
Does not come with power supply. Two open power supply slots are available;
three different power supplies are available.
See power supply products for additional
specifications.
2450 BTU/hr (2584.75 kJ/hr), (max. non-PoE);
3700 BTU/hr (3903 kJ/hr), (max. using PoE)
110–127/200–240 VAC, rated
(depending on power supply chosen)
215 W
Heat dissipation does not include heat
dissipated by the PoE-powered devices
themselves. When more than four power cords are installed in a 5412R zl2 switch
chassis, additional installation requirements
are needed. Refer to the HP 5400R zl2 Switches Quick Setup Guide and Safety/
Regulatory Information manual for details.
Idle power is the actual power
consumption of the device with no ports
connected.
Environment
Operating temperature
Operating relative humidity
Nonoperating/Storage temperature
Nonoperating/Storage relative humidity
Altitude
Acoustic
Electrical characteristics
Frequency
80plus.org Certification
Description
Maximum heat dissipation
Voltage
Idle power
Notes
Heat dissipation does not include heat
dissipated by the PoE-powered devices
themselves.
10
Data sheet | HP 5400R zl2 Switch Series
HP 5406R zl2 Switch (J9821A)
HP 5412R zl2 Switch (J9822A)
HP 5406R-44G-PoE+/2SFP+ (No PSU)
v2 zl2 Switch (J9823A)
Safety
CSA 22.2 No. 60950; UL 60950; IEC 60950; EN 60950
CSA 22.2 No. 60950; UL 60950; IEC 60950; EN 60950
CSA 22.2 No. 60950; UL 60950; IEC 60950;
EN 60950
Emissions
FCC part 15 Class A; EN 55022/CISPR 22 Class A
FCC part 15 Class A; EN 55022/CISPR 22 Class A
FCC part 15 Class A; EN 55022/CISPR 22 Class A
EN 55024, CISPR 24
IEC 61000-4-2; 4 kV CD, 8 kV AD; HP ENV. 765.002
IEC 61000-4-3; 3 V/m
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal line) IEC 61000-4-5; 1 kV/2 kV AC, 1 kV signal, 0.5 kV DC
IEC 61000-4-6; 3 Vrms
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
IEC 61000-4-11; >95% reduction, 0.5 period; 30% reduction, 25 periods
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
EN 55024, CISPR 24
IEC 61000-4-2; 4 kV CD, 8 kV AD; HP ENV. 765.002
IEC 61000-4-3; 3 V/m
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal line) IEC 61000-4-5; 1 kV/2 kV AC, 1 kV signal, 0.5 kV DC
IEC 61000-4-6; 3 Vrms
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
IEC 61000-4-11; >95% reduction, 0.5 period; 30% reduction, 25 periods
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
EN 55024, CISPR 24
IEC 61000-4-2; 4 kV CD, 8 kV AD; HP ENV. 765.002
IEC 61000-4-3; 3 V/m
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal line) IEC 61000-4-5; 1 kV/2 kV AC, 1 kV signal, 0.5 kV DC
IEC 61000-4-6; 3 Vrms
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
IEC 61000-4-11; >95% reduction, 0.5 period; 30% reduction, 25 periods
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
Management
IMC—Intelligent Management Center;
Command-line interface; Web browser;
Configuration menu; Out-of-band management (RJ-45 Ethernet); SNMP Manager; Out-of-band management (serial rs-232c or micro usb)
IMC—Intelligent Management Center;
Command-line interface; Web browser;
Configuration menu; Out-of-band management (RJ-45 Ethernet); SNMP Manager; Out-of-band management (serial rs-232c or micro usb)
IMC—Intelligent Management Center;
Command-line interface; Web browser;
Configuration menu; Out-of-band
management (RJ-45 Ethernet); SNMP
Manager; Out-of-band management
(serial rs-232c or micro usb)
Notes
Supported 1G SFP transceivers are revision “B” or later (product number ends with the letter “B” or later; For example, J9142B, J8177C).
Supported 1G SFP transceivers are revision “B” or later (product number ends with the letter “B” or later; For example, J9142B, J8177C).
Supported 1G SFP transceivers are
revision “B” or later (product number
ends with the letter “B” or later; For example, J9142B, J8177C).
Services
Refer to the HP website at hp.com/networking/services for details on
the service-level descriptions and product
numbers. For details about services and
response times in your area, please contact
your local HP sales office.
Refer to the HP website at hp.com/networking/services for details on
the service-level descriptions and product
numbers. For details about services and
response times in your area, please contact
your local HP sales office.
Refer to the HP website at hp.com/networking/services for details on
the service-level descriptions and product
numbers. For details about services
and response times in your area, please
contact your local HP sales office.
Immunity
EN
ESD
Radiated
EFT/Burst Surge
Conducted
Power frequency magnetic field
Harmonics
Flicker
11
Data sheet | HP 5400R zl2 Switch Series
HP 5400R zl2 Switch Series
Specifications (continued)
HP 5412R-92G-PoE+/2SFP+ (No PSU) v2
zl2 Switch (J9825A)
HP 5406R-44G-PoE+/4SFP (No PSU) v2
zl2 Switch (J9824A)
HP 5412R-92G-PoE+/4SFP (No PSU) v2
zl2 Switch (J9826A)
Included accessories
1 HP 5400R zl2 Management Module
(J9827A)
1 HP 5412R zl2 Switch Fan Tray (J9832A)
3 HP 24-port Gig-T PoE+ v2 zl Module
(J9534A)
1 HP 20-port Gig-T PoE+/2-port 10GbE
SFP+ v2 zl Module (J9536A)
1 HP 5400R zl2 Management Module
(J9827A)
1 HP 5406R zl2 Switch Fan Tray (J9831A)
1 HP 24-port Gig-T PoE+ v2 zl Module
(J9534A)
1 HP 20-port Gig-T PoE+/4-port SFP v2 zl
Module (J9535A)
1 HP 5400R zl2 Management Module
(J9827A)
1 HP 5412R zl2 Switch Fan Tray (J9832A)
3 HP 24-port Gig-T PoE+ v2 zl Module
(J9534A)
1 HP 20-port Gig-T PoE+/4-port SFP v2 zl
Module (J9535A)
I/O ports and slots
92 RJ-45 autosensing 10/100/1000 PoE+ ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE 802.3at PoE+); Media Type: Auto-MDIX;
Duplex: 10BASE-T/100BASE-TX: half or full;
1000BASE-T: full only
2 open 10GbE SFP+ transceiver slots
8 open module slots
Supports a maximum of 288 autosensing
10/100/1000 ports or 288 SFP ports or 96 SFP+ ports or 96 HP Smart Rate Multi-Gigabit or 24 40GbE ports, or a combination
44 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T);
Media Type: Auto-MDIX; Duplex: 10BASE-T/100BASE-TX: half or full;
1000BASE-T: full only
4 open mini-GBIC (SFP) slots
4 open module slots
Supports a maximum of 144 autosensing
10/100/1000 ports or 144 SFP ports or 48 SFP+ ports or 48 HP Smart Rate Multi-Gigabit or 12 40GbE ports, or a combination
92 RJ-45 autosensing 10/100/1000 PoE+
ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE 802.3at PoE+); Media Type: Auto-MDIX; Duplex: 10BASE-T/100BASE-TX: half or full;
1000BASE-T: full only
4 open mini-GBIC (SFP) slots
8 open module slots
Supports a maximum of 288 autosensing
10/100/1000 ports or 288 SFP ports or 96 SFP+ ports or 96 HP Smart Rate Multi-Gigabit or 24 40GbE ports, or a combination
Power supplies
4 power supply slots
2 minimum power supplies required (ordered separately)
2 power supply slots
1 minimum power supply required (ordered separately)
4 power supply slots
2 minimum power supplies required
(ordered separately)
Fan tray
Includes: 1 x J9832A
1 fan tray slot
Includes: 1 x J9831A
1 fan tray slot
Includes: 1 x J9832A
1 fan tray slot
17.5(w) x 17.75(d) x 12.1(h) in. (44.45 x 45.09 x 30.73 cm) (7U height)
45.19 lb (20.5 kg)
17.5(w) x 17.75(d) x 6.9(h) in. (44.45 x 45.09 x 17.53 cm) (4U height)
26.19 lb (11.88 kg)
17.5(w) x 17.75(d) x 12.1(h) in. (44.45 x 45.09 x 30.73 cm) (7U height)
45.4 lb (20.59 kg)
Dual ARM Coretex A9 @ 1 GHz; Packet buffer size: 13.5 MB internal
ARM 11 @ 450 MHz; Packet buffer size: 18 MB internal
Dual ARM Coretex A9 @ 1 GHz; Packet buffer size: 13.5 MB internal
ARM 11 @ 550 MHz; Packet buffer size: 18 MB internal
Dual ARM Coretex A9 @ 1 GHz; Packet buffer size: 13.5 MB internal
Freescale P2020 dual core @ 1.2 MHz, 16 MB flash, 1 GB SD Card, 4 GB DDR3 SODIMM
Dual ARM Coretex A9 @ 1 GHz; Packet buffer size: 13.5 MB internal
ARM 11 @ 450 MHz; Packet buffer size: 18 MB internal
Dual ARM Coretex A9 @ 1 GHz; Packet buffer size: 13.5 MB internal
ARM 11 @ 550 MHz; Packet buffer size: 18 MB internal
Dual ARM Coretex A9 @ 1; Packet buffer size: 13.5 MB internal
Freescale P2020 dual core @ 1.2 GHz, 16 MB flash, 1 GB SD Card, 4 GB DDR3 SODIMM
Dual ARM Coretex A9 @ 1 GHz; Packet buffer size: 13.5 MB internal
ARM 11 @ 450 MHz; Packet buffer size: 18 MB internal
Dual ARM Coretex A9 @ 1 GHz; Packet buffer size: 13.5 MB internal
ARM 11 @ 550 MHz; Packet buffer size: 18 MB internal
Dual ARM Coretex A9 @ 1 GHz; Packet buffer size: 13.5 MB internal
Freescale P2020 dual core @ 1.2 GHz, 16 MB flash, 1 GB SD Card, 4 GB DDR3 SODIMM
Physical characteristics
Dimensions
Weight
Memory and processor
v3 Gigabit Module
v2 Gigabit Module
v3 10G Module
v2 10G Module
v3 40G Module
Management Module
12
Data sheet | HP 5400R zl2 Switch Series
HP 5412R-92G-PoE+/2SFP+ (No PSU) v2
zl2 Switch (J9825A)
HP 5406R-44G-PoE+/4SFP (No PSU) v2
zl2 Switch (J9824A)
HP 5412R-92G-PoE+/4SFP (No PSU) v2
zl2 Switch (J9826A)
Mounting and enclosure
Mounts in an EIA standard 19-inch telco rack or equipment cabinet (hardware included); Horizontal surface mounting only
Mounts in an EIA standard 19-inch telco rack or equipment cabinet (hardware included); Horizontal surface mounting only
Mounts in an EIA standard 19-inch telco
rack or equipment cabinet (hardware
included); Horizontal surface mounting only
Performance
1000 Mb Latency
10 Gbps Latency
40 Gbps Latency
Throughput
Routing/Switching capacity
Switch fabric speed
Routing table size
MAC address table size
IPv6 Ready Certified
< 2.8 µs (FIFO 64-byte packets)
< 1.8 µs (FIFO 64-byte packets)
< 1.5 µs (FIFO 64-byte packets)
Up to 1142.8 Mpps
1920 Gbps
2030 Gbps
10000 entries (IPv4), 5000 entries (IPv6)
64000 entries
IPv6 Ready Certified
< 2.8 µs (FIFO 64-byte packets)
< 1.8 µs (FIFO 64-byte packets)
< 1.5 µs (FIFO 64-byte packets)
Up to 571.4 Mpps
960 Gbps
1015 Gbps
10000 entries (IPv4), 5000 entries (IPv6)
64000 entries
IPv6 Ready Certified
< 2.8 µs (FIFO 64-byte packets)
< 1.8 µs (FIFO 64-byte packets)
< 1.5 µs (FIFO 64-byte packets)
Up to 1142.8 Mpps
1920 Gbps
2030 Gbps
10000 entries (IPv4), 5000 entries (IPv6)
64000 entries
32°F to 113°F (0°C to 45°C); 0°C to 40°C with
J8177C transceiver installed, 0°C to 35°C with
FIPS Opacity Shield installed
15% to 95% @ 113°F (45°C), noncondensing
-40°F to 158°F (-40°C to 70°C)
15% to 95% @ 149°F (65°C), noncondensing
up to 10,000 ft (3 km)
Power: 49 dB, Pressure: 35.7 dB ISO 7779, ISO 9296
32°F to 113°F (0°C to 45°C); 0°C to 40°C with
J8177C transceiver installed, 0°C to 35°C with
FIPS Opacity Shield installed
15% to 95% @ 113°F (45°C), noncondensing
-40°F to 158°F (-40°C to 70°C)
15% to 95% @ 149°F (65°C), noncondensing
up to 10,000 ft (3 km)
Power: 44 dB, Pressure: 31.7 dB ISO 7779, ISO 9296
32°F to 113°F (0°C to 45°C); 0°C to 40°C
with J8177C transceiver installed, 0°C to
35°C with FIPS Opacity Shield installed
15% to 95% @ 113°F (45°C), noncondensing
-40°F to 158°F (-40°C to 70°C)
15% to 95% @ 149°F (65°C), noncondensing
up to 10,000 ft (3 km)
Power: 49 dB, Pressure: 35.7 dB ISO 7779, ISO 9296
50/60 Hz
Gold
Does not come with power supply. Four open power supply slots are available;
three different power supplies are available.
See power supply products for additional
specifications.
4900 BTU/hr (5169.5 kJ/hr), (max. non-PoE);
7400 BTU/hr (7807 kJ/hr), (max. using PoE)
110–127/200–240 VAC, rated (depending on power supply chosen)
312 W
50/60 Hz
Gold
Does not come with power supply. Two open power supply slots are available;
three different power supplies are available.
See power supply products for additional
specifications.
2450 BTU/hr (2584.75 kJ/hr), (max. non-PoE);
3700 BTU/hr (3903 kJ/hr), (max. using PoE)
110–127/200–240 VAC, rated (depending on power supply chosen)
215 W
50/60 Hz
Gold
Does not come with power supply. Four open power supply slots are available;
three different power supplies are available.
See power supply products for additional
specifications.
4900 BTU/hr (5169.5 kJ/hr), (max. non-PoE);
7400 BTU/hr (7807 kJ/hr), (max. using PoE)
110–127/200–240 VAC, rated
(depending on power supply chosen)
312 W
Notes
Idle power is the actual power consumption of the device with no ports connected.
Heat dissipation does not include heat
dissipated by the PoE-powered devices
themselves. When more than four power cords are installed in a 5412R zl2 switch
chassis, additional installation requirements
are needed. Refer to the HP 5400R zl2 Switches Quick Setup Guide and Safety/
Regulatory Information manual for details.
Idle power is the actual power consumption of the device with no ports connected.
Heat dissipation does not include heat
dissipated by the PoE-powered devices
themselves.
Idle power is the actual power
consumption of the device with no ports
connected.
Heat dissipation does not include heat
dissipated by the PoE-powered devices
themselves. When more than four
power cords are installed in a 5412R zl2
switch chassis, additional installation
requirements are needed. Refer to the
HP 5400R zl2 Switches Quick Setup
Guide and Safety/Regulatory Information
manual for details.
Environment
Operating temperature
Operating relative humidity
Nonoperating/Storage temperature
Nonoperating/Storage relative humidity
Altitude
Acoustic
Electrical characteristics
Frequency
80plus.org Certification
Description
Maximum heat dissipation
Voltage
Idle power
13
Data sheet | HP 5400R zl2 Switch Series
HP 5412R-92G-PoE+/2SFP+ (No PSU) v2
zl2 Switch (J9825A)
HP 5406R-44G-PoE+/4SFP (No PSU) v2
zl2 Switch (J9824A)
HP 5412R-92G-PoE+/4SFP (No PSU) v2
zl2 Switch (J9826A)
Safety
CSA 22.2 No. 60950; UL 60950; IEC 60950; EN 60950
CSA 22.2 No. 60950; UL 60950; IEC 60950; EN 60950
CSA 22.2 No. 60950; UL 60950; IEC 60950; EN 60950
Emissions
FCC part 15 Class A; EN 55022/CISPR 22 Class A
FCC part 15 Class A; EN 55022/CISPR 22 Class A
FCC part 15 Class A; EN 55022/CISPR 22 Class A
EN 55024, CISPR 24
IEC 61000-4-2; 4 kV CD, 8 kV AD; HP ENV. 765.002
IEC 61000-4-3; 3 V/m
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV
(signal line) IEC 61000-4-5; 1 kV/2 kV AC, 1 kV signal, 0.5 kV DC
IEC 61000-4-6; 3 Vrms
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
IEC 61000-4-11; >95% reduction, 0.5 period; 30% reduction, 25 periods
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
EN 55024, CISPR 24
IEC 61000-4-2; 4 kV CD, 8 kV AD;
HP ENV. 765.002
IEC 61000-4-3; 3 V/m
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV
(signal line) IEC 61000-4-5; 1 kV/2 kV AC, 1 kV signal, 0.5 kV DC
IEC 61000-4-6; 3 Vrms
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
IEC 61000-4-11; >95% reduction, 0.5 period;
30% reduction, 25 periods
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
EN 55024, CISPR 24
IEC 61000-4-2; 4 kV CD, 8 kV AD; HP ENV. 765.002
IEC 61000-4-3; 3 V/m
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV
(signal line) IEC 61000-4-5; 1 kV/2 kV AC,
1 kV signal, 0.5 kV DC
IEC 61000-4-6; 3 Vrms
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
IEC 61000-4-11; >95% reduction, 0.5 period; 30% reduction, 25 periods
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
Management
IMC—Intelligent Management Center;
Command-line interface; Web browser;
Configuration menu; Out-of-band management (RJ-45 Ethernet); SNMP Manager; Out-of-band management
(serial rs-232c or micro usb)
IMC—Intelligent Management Center;
Command-line interface; Web browser;
Configuration menu; Out-of-band management (RJ-45 Ethernet); SNMP Manager; Out-of-band management
(serial rs-232c or micro usb)
IMC—Intelligent Management Center;
Command-line interface; Web browser;
Configuration menu; Out-of-band
management (RJ-45 Ethernet); SNMP
Manager; Out-of-band management
(serial rs-232c or micro usb)
Notes
Supported 1G SFP transceivers are revision “B” or later (product number ends with the letter “B” or later; For example, J9142B, J8177C).
Supported 1G SFP transceivers are revision “B” or later (product number ends with the letter “B” or later; For example, J9142B, J8177C).
Supported 1G SFP transceivers are
revision “B” or later (product number
ends with the letter “B” or later; For example, J9142B, J8177C).
Services
Refer to the HP website at hp.com/networking/services for details on
the service-level descriptions and product
numbers. For details about services and
response times in your area, please contact
your local HP sales office.
Refer to the HP website at hp.com/networking/services for details on
the service-level descriptions and product
numbers. For details about services and
response times in your area, please contact
your local HP sales office.
Refer to the HP website at hp.com/networking/services for details
on the service-level descriptions and
product numbers. For details about
services and response times in your area,
please contact your local HP sales office.
Immunity
EN
ESD
Radiated
EFT/Burst Surge
Conducted
Power frequency magnetic field
Harmonics
Flicker
14
Data sheet | HP 5400R zl2 Switch Series
HP 5400R zl2 Switch Series
Specifications (continued)
HP 5406R-8XGT/8SFP+ (No PSU) v2 zl2
Switch (J9868A)
HP 5412R 92GT PoE+/4SFP+ (No PSU)
v3 zl2 Switch (JL001A)
HP 5406R 8-port 1/2.5/5/10GBASE-T PoE+/
8-port SFP+ (No PSU) v3 zl2 Switch (JL002A)
Included accessories
1 HP 5400R zl2 Management Module (J9827A)
1 HP 5406R zl2 Switch Fan Tray (J9831A)
1 HP 8-port 10GbE SFP+ v2 zl Module
(J9538A)
1 HP 8-port 10GBASE-T v2 zl Module
(J9546A)
1 HP 5400R zl2 Management Module (J9827A)
1 HP 5412R zl2 Switch Fan Tray (J9832A)
3 HP 24-port 10/100/1000BASE-T PoE+
MACsec v3 zl2 Module (J9986A)
1 HP 20-port 10/100/1000BASE-T PoE+/
4-port 1G/10GbE SFP+ MACsec v3 zl2
Module (J9990A)
1 HP 5400R zl2 Management Module (J9827A)
1 HP 5406R zl2 Switch Fan Tray (J9831A)
1 HP 8-port 1G/10GbE SFP+ MACsec v3 zl2
Module (J9993A)
1 HP 8-port 1/2.5/5/10GBASE-T PoE+
MACsec v3 zl2 Module (J9995A)
I/O ports and slots
8 RJ-45 10GbE ports (IEEE 802.3an-2006
Type 10GBASE-T)
8 open 10GbE SFP+ transceiver slots
4 open module slots
Supports a maximum of 144 autosensing
10/100/1000 ports or 144 SFP ports or 48 SFP+ ports or 48 HP Smart Rate Multi-Gigabit or 12 40GbE ports, or a
combination
92 RJ-45 autosensing 10/100/1000 PoE+
ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE 802.3at PoE+); Media Type: Auto-MDIX;
Duplex: 10BASE-T/100BASE-TX: half or full;
1000BASE-T: full only
4 open 10GbE SFP+ transceiver slots
8 open module slots
Supports a maximum of 288 autosensing
10/100/1000 ports or 288 SFP ports or 96 SFP+ ports or 96 HP Smart Rate Multi-Gigabit or 24 40GbE ports, or a
combination
8 RJ-45 HP Smart Rate Multi-Gigabit ports
8 open 10GbE SFP+ transceiver slots
4 open module slots
Supports a maximum of 144 autosensing
10/100/1000 ports or 144 SFP ports
or 48 SFP+ ports or 48 HP Smart Rate
Multi-Gigabit or 12 40GbE ports, or a
combination
Power supplies
2 power supply slots
1 minimum power supply required (ordered separately)
4 power supply slots
2 minimum power supplies required
(ordered separately)
2 power supply slots
1 minimum power supply required
(ordered separately)
Fan tray
Includes: 1 x J9831A
1 fan tray slot
Includes: 1 x J9832A
1 fan tray slot
Includes: 1 x J9831A
1 fan tray slot
17.5(w) x 17.75(d) x 6.9(h) in. (44.45 x 45.09 x 17.53 cm) (4U height)
28.11 lb (12.75 kg)
17.5(w) x 17.75(d) x 12.1(h) in. (44.45 x 45.09 x 30.73 cm) (7U height)
45.19 lb (20.5 kg)
17.5(w) x 17.75(d) x 6.9(h) in. (44.45 x 45.09 x 17.53 cm) (4U height)
28.11 lb (12.75 kg)
Dual ARM Coretex A9 @ 1 GHz; Packet buffer size: 13.5 MB internal
ARM 11 @ 450 MHz; Packet buffer size: 18 MB internal
Dual ARM Coretex A9 @ 1 GHz; Packet buffer size: 13.5 MB internal
ARM 11 @ 550 MHz; Packet buffer size: 18 MB internal
Dual ARM Coretex A9 @ 1 GHz; Packet buffer size: 13.5 MB internal
Freescale P2020 dual core @ 1.2 GHz, 16 MB flash, 1 GB SD Card, 4 GB DDR3
SODIMM
Dual ARM Coretex A9 @ 1 GHz; Packet buffer size: 13.5 MB internal
ARM 11 @ 450 MHz; Packet buffer size: 18 MB internal
Dual ARM Coretex A9 @ 1 GHz; Packet buffer size: 13.5 MB internal
ARM 11 @ 550 MHz; Packet buffer size: 18 MB internal
Dual ARM Coretex A9 @ 1 GHz; Packet buffer size: 13.5 MB internal
Freescale P2020 dual core @ 1.2 MHz, 16 MB flash, 1 GB SD Card, 4 GB DDR3
SODIMM
Dual ARM Coretex A9 @ 1 GHz; Packet buffer size: 13.5 MB internal
ARM 11 @ 450 MHz; Packet buffer size: 18 MB internal
Dual ARM Coretex A9 @ 1 GHz; Packet buffer size: 13.5 MB internal
ARM 11 @ 550 MHz; Packet buffer size: 18 MB internal
Dual ARM Coretex A9 @ 1 GHz; Packet buffer size: 13.5 MB internal
Freescale P2020 dual core @ 1.2 GHz,
16 MB flash, 1 GB SD Card, 4 GB DDR3
SODIMM
Physical characteristics
Dimensions
Weight
Memory and processor
v3 Gigabit Module
v2 Gigabit Module
v3 10G Module
v2 10G Module
v3 40G Module
Management Module
15
Data sheet | HP 5400R zl2 Switch Series
HP 5406R-8XGT/8SFP+ (No PSU) v2 zl2
Switch (J9868A)
HP 5412R 92GT PoE+/4SFP+ (No PSU)
v3 zl2 Switch (JL001A)
HP 5406R 8-port 1/2.5/5/10GBASE-T PoE+/
8-port SFP+ (No PSU) v3 zl2 Switch (JL002A)
Mounting and enclosure
Mounts in an EIA standard 19-inch telco rack
or equipment cabinet (hardware included);
Horizontal surface mounting only
Mounts in an EIA standard 19-inch telco rack
or equipment cabinet (hardware included);
Horizontal surface mounting only
Mounts in an EIA standard 19-inch telco rack
or equipment cabinet (hardware included);
Horizontal surface mounting only
Performance
1000 Mb Latency
10 Gbps Latency
40 Gbps Latency
Throughput
Routing/Switching capacity
Switch fabric speed
Routing table size
MAC address table size
IPv6 Ready Certified
< 2.8 µs (FIFO 64-byte packets)
< 1.8 µs (FIFO 64-byte packets)
< 1.5 µs (FIFO 64-byte packets)
up to 571.4 Mpps
960 Gbps
1015 Gbps
10000 entries (IPv4), 5000 entries (IPv6)
64000 entries
< 2.8 µs (FIFO 64-byte packets)
< 1.8 µs (FIFO 64-byte packets)
< 1.5 µs (FIFO 64-byte packets)
up to 1142.8 Mpps
1920 Gbps
2030 Gbps
10000 entries (IPv4), 5000 entries (IPv6)
64000 entries
< 2.8 µs (FIFO 64-byte packets)
< 1.8 µs (FIFO 64-byte packets)
< 1.5 µs (FIFO 64-byte packets)
up to 571.4 Mpps
960 Gbps
1015 Gbps
10000 entries (IPv4), 5000 entries (IPv6)
64000 entries
32°F to 113°F (0°C to 45°C); 0°C to 40°C with J8177C transceiver installed, 0°C to 35°C with FIPS Opacity Shield installed
15% to 95% @ 113°F (45°C), noncondensing
-40°F to 158°F (-40°C to 70°C)
15% to 95% @ 149°F (65°C), noncondensing
Up to 10,000 ft (3 km)
Power: 44 dB, Pressure: 31.7 dB ISO 7779, ISO 9296
32°F to 113°F (0°C to 45°C); 0°C to 40°C with J8177C transceiver installed, 0°C to 35°C with FIPS Opacity Shield installed
15% to 95% @ 113°F (45°C), noncondensing
-40°F to 158°F (-40°C to 70°C)
15% to 95% @ 149°F (65°C), noncondensing
Up to 10,000 ft (3 km)
Power: 49 dB, Pressure: 35.7 dB ISO 7779, ISO 9296
32°F to 113°F (0°C to 45°C); 0°C to 40°C
with J8177C transceiver installed, 0°C to
35°C with FIPS Opacity Shield installed
15% to 95% @ 113°F (45°C), noncondensing
-40°F to 158°F (-40°C to 70°C)
15% to 95% @ 149°F (65°C), noncondensing
Up to 10,000 ft (3 km)
Power: 44 dB, Pressure: 31.7 dB ISO 7779, ISO 9296
50/60 Hz
Gold
Does not come with power supply. Two open power supply slots are available;
three different power supplies are available.
See power supply products for additional
specifications.
2450 BTU/hr (2584.75 kJ/hr), (max. non-PoE);
3700 BTU/hr (3903 kJ/hr), (max. using PoE)
110–127/200–240 VAC, rated (depending on power supply chosen)
215 W
50/60 Hz
Gold
Does not come with power supply. Four open power supply slots are available;
three different power supplies are available.
See power supply products for additional
specifications.
4900 BTU/hr (5169.5 kJ/hr), (max. non-PoE);
7400 BTU/hr (7807 kJ/hr), (max. using PoE)
110–127/200–240 VAC, rated
(depending on power supply chosen)
312 W
50/60 Hz
Gold
Does not come with power supply. Two open power supply slots are available;
three different power supplies are
available. See power supply products for
additional specifications.
2450 BTU/hr (2584.75 kJ/hr), (max. non-PoE);
3700 BTU/hr (3903 kJ/hr), (max. using PoE)
110–127/200–240 VAC, rated (depending
on power supply chosen)
215 W
Idle power is the actual power consumption of the device with no ports connected.
Heat dissipation does not include heat
dissipated by the PoE-powered devices
themselves. When more than four power cords are installed in a 5412R zl2 switch
chassis, additional installation requirements
are needed. Refer to the HP 5400R zl2 Switches Quick Setup Guide and Safety/
Regulatory Information manual for details.
Idle power is the actual power
consumption of the device with no ports
connected.
Heat dissipation does not include heat
dissipated by the PoE-powered devices
themselves.
Environment
Operating temperature
Operating relative humidity
Nonoperating/Storage temperature
Nonoperating/Storage relative humidity
Altitude
Acoustic
Electrical characteristics
Frequency
80plus.org Certification
Description
Maximum heat dissipation
Voltage
Idle power
Notes
Idle power is the actual power consumption of the device with no ports connected.
Heat dissipation does not include heat
dissipated by the PoE-powered devices
themselves.
16
Data sheet | HP 5400R zl2 Switch Series
HP 5406R-8XGT/8SFP+ (No PSU) v2 zl2
Switch (J9868A)
HP 5412R 92GT PoE+/4SFP+ (No PSU)
v3 zl2 Switch (JL001A)
HP 5406R 8-port 1/2.5/5/10GBASE-T PoE+/
8-port SFP+ (No PSU) v3 zl2 Switch (JL002A)
Safety
CSA 22.2 No. 60950; UL 60950; IEC 60950; EN 60950
CSA 22.2 No. 60950; UL 60950; IEC 60950; EN 60950
CSA 22.2 No. 60950; UL 60950; IEC 60950; EN 60950
Emissions
FCC part 15 Class A; EN 55022/CISPR 22 Class A
FCC part 15 Class A; EN 55022/CISPR 22 Class A
FCC part 15 Class A; EN 55022/CISPR 22 Class A
EN 55024, CISPR 24
IEC 61000-4-2; 4 kV CD, 8 kV AD; HP ENV. 765.002
IEC 61000-4-3; 3 V/m
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV
(signal line) IEC 61000-4-5; 1 kV/2 kV AC, 1 kV signal, 0.5 kV DC
IEC 61000-4-6; 3 Vrms
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
IEC 61000-4-11; >95% reduction, 0.5 period; 30% reduction, 25 periods
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
EN 55024, CISPR 24
IEC 61000-4-2; 4 kV CD, 8 kV AD; HP ENV. 765.002
IEC 61000-4-3; 3 V/m
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV
(signal line) IEC 61000-4-5; 1 kV/2 kV AC, 1 kV signal, 0.5 kV DC
IEC 61000-4-6; 3 Vrms
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
IEC 61000-4-11; >95% reduction, 0.5 period; 30% reduction, 25 periods
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
EN 55024, CISPR 24
IEC 61000-4-2; 4 kV CD, 8 kV AD; HP ENV. 765.002
IEC 61000-4-3; 3 V/m
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV
(signal line) IEC 61000-4-5; 1 kV/2 kV AC,
1 kV signal, 0.5 kV DC
IEC 61000-4-6; 3 Vrms
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
IEC 61000-4-11; >95% reduction, 0.5 period; 30% reduction, 25 periods
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
Management
IMC—Intelligent Management Center;
Command-line interface; Web browser;
Configuration menu; Out-of-band management (RJ-45 Ethernet); SNMP Manager; Out-of-band management
(serial rs-232c or micro usb)
IMC—Intelligent Management Center;
Command-line interface; Web browser;
Configuration menu; Out-of-band management (RJ-45 Ethernet); SNMP Manager; Out-of-band management
(serial rs-232c or micro usb)
IMC—Intelligent Management Center;
Command-line interface; Web browser;
Configuration menu; Out-of-band
management (RJ-45 Ethernet); SNMP Manager; Out-of-band management (serial rs-232c or micro usb)
Notes
Supported 1G SFP transceivers are revision “B” Supported 1G SFP transceivers are revision “B” Supported 1G SFP transceivers are
or later (product number ends with the letter or later (product number ends with the letter revision “B” or later (product number
“B” or later; For example, J9142B, J8177C).
“B” or later; For example, J9142B, J8177C).
ends with the letter “B” or later; For
example, J9142B, J8177C).
HP Smart Rate Multi-Gigabit Cabling;
1000BASE-T, 2.5 Gigabit, and 5 Gigabit
Ethernet: Category 5e or better UTP or
STP; 10GBASE-T: Category 6 or better
(CAT6A recommended) UTP or STP
Services
Refer to the HP website at hp.com/networking/services for details on
the service-level descriptions and product
numbers. For details about services and
response times in your area, please contact
your local HP sales office.
Immunity
EN
ESD
Radiated
EFT/Burst Surge
Conducted
Power frequency magnetic field
Harmonics
Flicker
Refer to the HP website at hp.com/networking/services for details on
the service-level descriptions and product
numbers. For details about services and
response times in your area, please contact
your local HP sales office.
Refer to the HP website at hp.com/networking/services for details
on the service-level descriptions and
product numbers. For details about
services and response times in your area,
please contact your local HP sales office.
17
Data sheet | HP 5400R zl2 Switch Series
HP 5400R zl2 Switch Series
Specifications (continued)
HP 5406R 44GT PoE+/4SFP+ (No PSU) v3 zl2 Switch (JL003A)
HP 5406R 16-port SFP+ (No PSU) v3 zl2 Switch (JL095A)
Included accessories
1 HP 5400R zl2 Management Module (J9827A)
1 HP 5406R zl2 Switch Fan Tray (J9831A)
1 HP 24-port 10/100/1000BASE-T PoE+ MACsec v3 zl2
Module (J9986A)
1 HP 20-port 10/100/1000BASE-T PoE+/4-port 1G/10GbE
SFP+ MACsec v3 zl2 Module (J9990A)
1 HP 5400R zl2 Management Module (J9827A)
1 HP 5406R zl2 Switch Fan Tray (J9831A)
2 HP 8-port 1G/10GbE SFP+ MACsec v3 zl2 Module
(J9993A)
I/O ports and slots
44 RJ-45 autosensing 10/100/1000 PoE+ ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE 802.3at PoE+); Media Type: Auto-MDIX; Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only
4 open 10GbE SFP+ transceiver slots
4 open module slots
Supports a maximum of 144 autosensing 10/100/1000 ports or 144 SFP ports or 48 SFP+ ports or
48 HP Smart Rate Multi-Gigabit or 12 40GbE ports, or a
combination
16 open 10GbE SFP+ transceiver slots
4 open module slots
Supports a maximum of 144 autosensing 10/100/1000 ports or 144 SFP ports or 48 SFP+ ports or
48 HP Smart Rate Multi-Gigabit or 12 40GbE ports, or a
combination
Power supplies
2 power supply slots
1 minimum power supply required (ordered separately)
2 power supply slots
1 minimum power supply required (ordered separately)
Fan tray
Includes: 1 x J9831A
1 fan tray slot
Includes: 1 x J9831A
1 fan tray slot
17.5(w) x 17.75(d) x 6.9(h) in. (44.45 x 45.09 x 17.53 cm) (4U height)
28.11 lb (12.75 kg)
17.5(w) x 17.75(d) x 6.9(h) in. (44.45 x 45.09 x 17.53 cm)
(4U height)
28.11 lb (12.75 kg)
Dual ARM Coretex A9 @ 1 GHz; Packet buffer size: 13.5 MB internal
ARM 11 @ 450 MHz; Packet buffer size: 18 MB internal
Dual ARM Coretex A9 @ 1 GHz; Packet buffer size: 13.5 MB internal
ARM 11 @ 550 MHz; Packet buffer size: 18 MB internal
Dual ARM Coretex A9 @ 1 GHz; Packet buffer size: 13.5 MB internal
Freescale P2020 dual core @ 1.2 GHz, 16 MB flash, 1 GB SD Card, 4 GB DDR3 SODIMM
Dual ARM Coretex A9 @ 1 GHz; Packet buffer size: 13.5 MB internal
ARM 11 @ 450 MHz; Packet buffer size: 18 MB internal
Dual ARM Coretex A9 @ 1; Packet buffer size: 13.5 MB internal
ARM 11 @ 550 MHz; Packet buffer size: 18 MB internal
Dual ARM Coretex A9 @ 1 GHz; Packet buffer size: 13.5 MB internal
Freescale P2020 dual core @ 1.2 GHz, 16 MB flash, 1 GB SD Card, 4 GB DDR3 SODIMM
Mounts in an EIA standard 19-inch telco rack or equipment cabinet (hardware included); Horizontal surface mounting only
Mounts in an EIA standard 19-inch telco rack or
equipment cabinet (hardware included); Horizontal
surface mounting only
Physical characteristics
Dimensions
Weight
Memory and processor
v3 Gigabit Module
v2 Gigabit Module
v3 10G Module
v2 10G Module
v3 40G Module
Management Module
Mounting and enclosure
18
Data sheet | HP 5400R zl2 Switch Series
Performance
1000 Mb Latency
10 Gbps Latency
40 Gbps Latency
Throughput
Routing/Switching capacity
Switch fabric speed
Routing table size
MAC address table size
Environment
Operating temperature
Operating relative humidity
Nonoperating/Storage temperature
Nonoperating/Storage relative humidity
Altitude
Acoustic
Electrical characteristics
Frequency
80plus.org Certification
Description
Maximum heat dissipation
Voltage
Idle power
HP 5406R 44GT PoE+/4SFP+ (No PSU) v3 zl2 Switch (JL003A)
HP 5406R 16-port SFP+ (No PSU) v3 zl2 Switch (JL095A)
< 2.8 µs (FIFO 64-byte packets)
< 1.8 µs (FIFO 64-byte packets)
< 1.5 µs (FIFO 64-byte packets)
up to 571.4 Mpps
960 Gbps
1015 Gbps
10000 entries (IPv4), 5000 entries (IPv6)
64000 entries
< 2.8 µs (FIFO 64-byte packets)
< 1.8 µs (FIFO 64-byte packets)
< 1.5 µs (FIFO 64-byte packets)
up to 571.4 Mpps
960 Gbps
1015 Gbps
10000 entries (IPv4), 5000 entries (IPv6)
64000 entries
32°F to 113°F (0°C to 45°C); 0°C to 40°C with J8177C transceiver installed, 0°C to 35°C with FIPS Opacity Shield
installed
15% to 95% @ 113°F (45°C), noncondensing
-40°F to 158°F (-40°C to 70°C)
15% to 95% @ 149°F (65°C), noncondensing
Up to 10,000 ft (3 km)
Power: 44 dB, Pressure: 31.7 dB ISO 7779, ISO 9296
32°F to 113°F (0°C to 45°C); 0°C to 40°C with J8177C
transceiver installed, 0°C to 35°C with FIPS Opacity Shield
installed
15% to 95% @ 113°F (45°C), noncondensing
-40°F to 158°F (-40°C to 70°C)
15% to 95% @ 149°F (65°C), noncondensing
Up to 10,000 ft (3 km)
Power: 44 dB, Pressure: 31.7 dB ISO 7779, ISO 9296
50/60 Hz
Gold
Does not come with power supply. Two open power supply slots are available; three different power supplies
are available. See power supply products for additional
specifications.
2450 BTU/hr (2584.75 kJ/hr), (max. non-PoE); 3700 BTU/hr (3903 kJ/hr), (max. using PoE)
110–127/200–240 VAC, rated (depending on power supply chosen)
215 W
50/60 Hz
Gold
Does not come with power supply. Two open power
supply slots are available; three different power supplies
are available. See power supply products for additional
specifications.
2450 BTU/hr (2584.75 kJ/hr), (max. non-PoE); 3700 BTU/hr (3903 kJ/hr), (max. using PoE)
110–127/200–240 VAC, rated (depending on power
supply chosen)
215 W
Notes
Idle power is the actual power consumption of the device with no ports connected. Heat dissipation does
not include heat dissipated by the PoE-powered devices
themselves.
Idle power is the actual power consumption of the
device with no ports connected. Heat dissipation does
not include heat dissipated by the PoE-powered devices
themselves.
19
Data sheet | HP 5400R zl2 Switch Series
HP 5406R 44GT PoE+/4SFP+ (No PSU) v3 zl2 Switch (JL003A)
HP 5406R 16-port SFP+ (No PSU) v3 zl2 Switch (JL095A)
Safety
CSA 22.2 No. 60950; UL 60950; IEC 60950; EN 60950
CSA 22.2 No. 60950; UL 60950; IEC 60950; EN 60950
Emissions
FCC part 15 Class A; EN 55022/CISPR 22 Class A
FCC part 15 Class A; EN 55022/CISPR 22 Class A
EN 55024, CISPR 24
IEC 61000-4-2; 4 kV CD, 8 kV AD; HP ENV. 765.002
IEC 61000-4-3; 3 V/m
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal line)
IEC 61000-4-5; 1 kV/2 kV AC, 1 kV signal, 0.5 kV DC
IEC 61000-4-6; 3 Vrms
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
IEC 61000-4-11; >95% reduction, 0.5 period; 30% reduction, 25 periods
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
EN 55024, CISPR 24
IEC 61000-4-2; 4 kV CD, 8 kV AD; HP ENV. 765.002
IEC 61000-4-3; 3 V/m
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal line)
IEC 61000-4-5; 1 kV/2 kV AC, 1 kV signal, 0.5 kV DC
IEC 61000-4-6; 3 Vrms
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
IEC 61000-4-11; >95% reduction, 0.5 period; 30% reduction, 25 periods
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
Management
IMC–Intelligent Management Center; Command-line interface; Web browser; Configuration menu; Out-of-band
management (RJ-45 Ethernet); SNMP Manager; Out-of-band
management (serial rs-232c or micro usb)
IMC–Intelligent Management Center; Command-line
interface; Web browser; Configuration menu; Out-of-band
management (RJ-45 Ethernet); SNMP Manager; Out-ofband management (serial rs-232c or micro usb)
Notes
Supported 1G SFP transceivers are revision “B” or later (product number ends with the letter “B” or later; For example, J9142B, J8177C).
Supported 1G SFP transceivers are revision “B” or later
(product number ends with the letter “B” or later; For example, J9142B, J8177C).
Services
Refer to the HP website at hp.com/networking/services for details on the service-level descriptions and product
numbers. For details about services and response times in your area, please contact your local HP sales office.
Refer to the HP website at hp.com/networking/services
for details on the service-level descriptions and product
numbers. For details about services and response times
in your area, please contact your local HP sales office.
Immunity
EN
ESD
Radiated
EFT/Burst
Surge
Conducted
Power frequency magnetic field
Voltage dips and interruptions Harmonics
Flicker
20
Data sheet | HP 5400R zl2 Switch Series
Standards and Protocols
(applies to all products in series)
BGP
RFC 1997 BGP Communities Attribute
RFC 2918 Route Refresh Capability
RFC 4271 A Border Gateway Protocol 4 (BGP-4)
RFC 4456 BGP Route Reflection: An Alternative RFC 5492 Capabilities Advertisement
to Full Mesh Internal BGP (IBGP)
with BGP-4
Device management
RFC 1591 DNS (client)
HTML and telnet management
General protocols
IEEE 802.1ad Q-in-Q
IEEE 802.1AX-2008 Link Aggregation
IEEE 802.1D MAC Bridges
IEEE 802.1p Priority
IEEE 802.1Q VLANs
IEEE 802.1s Multiple Spanning Trees
IEEE 802.1v VLAN classification by Protocol and Port
IEEE 802.1w Rapid Reconfiguration of Spanning Tree
IEEE 802.3ad Link Aggregation Control Protocol (LACP)
IEEE 802.3af Power over Ethernet
IEEE 802.3x Flow Control
RFC 768 UDP
RFC 783 TFTP Protocol (revision 2)
RFC 792 ICMP
RFC 793 TCP
RFC 826 ARP
RFC 854 TELNET
RFC 868 Time Protocol
RFC 951 BOOTP
RFC 1058 RIPv1
RFC 1350 TFTP Protocol (revision 2)
RFC 1519 CIDR
RFC 1542 BOOTP Extensions
RFC 1918 Address Allocation for Private Internet
RFC 2030 Simple Network Time Protocol (SNTP) v4
RFC 2131 DHCP
RFC 2453 RIPv2
RFC 2548 (MS-RAS-Vendor only)
RFC 3046 DHCP Relay Agent Information
Option
RFC 3576 Ext to RADIUS (CoA only)
RFC 3768 VRRP
RFC 4675 RADIUS VLAN & Priority UDLD
(Uni-Directional Link Detection)
IP multicast
RFC 3376 IGMPv3 (host joins only)
RFC 3973 PIM Dense Mode
RFC 4601 PIM Sparse Mode
IPv6
RFC 1981 IPv6 Path MTU Discovery
RFC 2375 IPv6 Multicast Address Assignments
RFC 2460 IPv6 Specification
RFC 2464 Transmission of IPv6 over Ethernet Networks
RFC 2710 Multicast Listener Discovery (MLD) for IPv6
RFC 2925 Definitions of Managed Objects
for Remote Ping, Traceroute, and Lookup
Operations (Ping only)
RFC 3019 MLDv1 MIB
RFC 3315 DHCPv6 (client and relay)
RFC 3484 Default Address Selection for IPv6
RFC 3587 IPv6 Global Unicast Address Format
RFC 3596 DNS Extension for IPv6
RFC 3810 MLDv2 for IPv6
RFC 4022 MIB for TCP
RFC 4087 IP Tunnel MIB
RFC 4113 MIB for UDP
RFC 4213 Basic Transition Mechanisms for IPv6 Hosts and Routers
RFC 4251 SSHv6 Architecture
RFC 4252 SSHv6 Authentication
RFC 4253 SSHv6 Transport Layer
RFC 4254 SSHv6 Connection
RFC 4291 IP Version 6 Addressing Architecture
RFC 4293 MIB for IP
RFC 4294 IPv6 Node Requirements
RFC 4419 Key Exchange for SSH
RFC 4443 ICMPv6
RFC 4541 IGMP & MLD Snooping Switch
RFC 4861 IPv6 Neighbor Discovery
RFC 4862 IPv6 Stateless Address Auto-configuration
RFC 5095 Deprecation of Type 0 Routing
Headers in IPv6
RFC 5340 OSPFv3 for IPv6
RFC 5453 Reserved IPv6 Interface
Identifiers
RFC 5519 Multicast Group Membership
Discovery MIB (MLDv2 only)
RFC 5722 Handling of Overlapping IPv6
Fragments
21
Data sheet | HP 5400R zl2 Switch Series
Standards and Protocols (continued)
(applies to all products in series)
MIBs
IEEE 802.1ap (MSTP and STP MIB’s only)
RFC 1155 Structure & ID of Mgmt Info for TCP/
IP Internets
RFC 1213 MIB II
RFC 1493 Bridge MIB
RFC 1724 RIPv2 MIB
RFC 1850 OSPFv2 MIB
RFC 2021 RMONv2 MIB
RFC 2096 IP Forwarding Table MIB
RFC 2578 Structure of Management
Information Version 2 (SMIv2)
RFC 2613 SMON MIB
RFC 2618 RADIUS Client MIB
RFC 2620 RADIUS Accounting MIB
RFC 2665 Ethernet-Like-MIB
RFC 2668 802.3 MAU MIB
RFC 2674 802.1p and IEEE 802.1Q Bridge MIB
RFC 2737 Entity MIB (Version 2)
RFC 2787 VRRP MIB
RFC 2863 The Interfaces Group MIB
RFC 2925 Ping MIB
RFC 2932 IP (Multicast Routing MIB)
RFC 2933 IGMP MIB
RFC 4292 IP Forwarding Table MIB
RFC 4836 Managed Objects for 802.3
Medium Attachment Units (MAU)
Network management
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
RFC 2819 Four groups of RMON: 1 (statistics), 2 (history), 3 (alarm), and 9 (events)
RFC 3176 sFlow
RFC 5424 Syslog Protocol
ANSI/TIA-1057 LLDP Media Endpoint Discovery (LLDP-MED)
SNMPv1/v2c/v3
XRMON
OSPF
RFC 2328 OSPFv2
RFC 3101 OSPF NSSA
RFC 5340 OSPFv3 for IPv6
QoS/CoS
RFC 2474 DiffServ Precedence, including 8 queues/port
RFC 2597 DiffServ Assured Forwarding (AF)
RFC 2598 DiffServ Expedited Forwarding (EF)
Security
IEEE 802.1AE MAC Security Standard (MACsec)
IEEE 802.1X Port Based Network Access Control
RFC 1492 TACACS+
RFC 2865 RADIUS (client only)
RFC 2866 RADIUS Accounting
RFC 3579 RADIUS Support For Extensible
Authentication Protocol (EAP)
Secure Sockets Layer (SSL)
SSHv2 Secure Shell
22
Data sheet | HP 5400R zl2 Switch Series
HP 5400R zl2 Switch Series accessories
Modules
NEW HP 8-port 1/2.5/5/10GBASE-T PoE+ MACsec v3 zl2 Module (J9995A)
HP 8-port 10GBASE-T v2 zl Module (J9546A)
NEW HP 8-port 1G/10GbE SFP+ MACsec v3 zl2 Module (J9993A) HP 8-port 10GbE SFP+ v2 zl Module (J9538A)
NEW HP 12-port 10/100/1000BASE-T PoE+/12-port 1GbE SFP MACsec v3 zl2 Module (J9989A)
HP 12-port Gig-T PoE+/12-port SFP v2 zl Module (J9637A)
HP 20-port Gig-T/4-port SFP v2 zl Module (J9549A)
HP 20-port Gig-T/2-port 10GbE SFP+ v2 zl Module (J9548A)
NEW HP 20-port 10/100/1000BASE-T PoE+/4-port 1G/10GbE SFP+ MACsec v3 zl2 Module (J9990A)
HP 20-port Gig-T PoE+/2-port 10GbE SFP+ v2 zl Module (J9536A)
HP 20-port Gig-T PoE+/4-port SFP v2 zl Module (J9535A) NEW HP 20-port 10/100/1000BASE-T PoE+/4p 1/2.5/5/10GBASE-T PoE+ MACsec v3 zl2 Module (J9991A) NEW HP 20-port 10/100/1000BASE-T PoE+ MACsec/1-port 40GbE QSFP+ v3 zl2 Module (J9992A)
HP 24-port 10/100 PoE+ v2 zl Module (J9547A)
NEW HP 24-port 10/100/1000BASE-T MACsec v3 zl2 Module (J9987A)
HP 24-port Gig-T v2 zl Module (J9550A)
NEW HP 24-port 10/100/1000BASE-T PoE+ MACsec v3 zl2 Module (J9986A)
HP 24-port Gig-T PoE+ v2 zl Module (J9534A)
NEW HP 24-port 1GbE SFP MACsec v3 zl2 Module (J9988A)
HP 24-port SFP v2 zl Module (J9537A)
NEW HP 2-port 40GbE QSFP+ v3 zl2 Module (J9996A)
HP Advanced Services v2 zl Module with HDD (J9857A)
HP Advanced Services v2 zl Module with SSD (J9858A)
HP 5400R zl2 Management Module (J9827A)
Transceivers
HP X131 10G X2 SC ER Transceiver (J8438A)
HP X131 10G X2 SC SR Transceiver (J8436A)
HP X131 10G X2 CX4 Transceiver (J8440C)
HP X111 100M SFP LC FX Transceiver (J9054C)
HP X131 10G X2 SC LR Transceiver (J8437A)
HP X131 10G X2 SC LRM Transceiver (J9144A)
HP X112 100M SFP LC BX-D Transceiver (J9099B)
HP X112 100M SFP LC BX-U Transceiver (J9100B)
HP X132 10G SFP+ LC SR Transceiver (J9150A)
HP X132 10G SFP+ LC LR Transceiver (J9151A)
HP X132 10G SFP+ LC LRM Transceiver (J9152A)
HP X121 1G SFP LC LH Transceiver (J4860C)
HP X121 1G SFP LC SX Transceiver (J4858C)
HP X121 1G SFP LC LX Transceiver (J4859C)
HP X121 1G SFP RJ45 T Transceiver (J8177C)
HP X122 1G SFP LC BX-D Transceiver (J9142B)
HP X122 1G SFP LC BX-U Transceiver (J9143B)
HP X132 10G SFP+ LC ER Transceiver (J9153A)
NEW HP X142 40G QSFP+ MPO SR4 Transceiver (JH231A)
NEW HP X142 40G QSFP+ LC LR4 SM Transceiver (JH232A)
NEW HP X142 40G QSFP+ MPO eSR4 300M XCVR (JH233A)
23
Data sheet | HP 5400R zl2 Switch Series
HP 5400R zl2 Switch Series accessories (continued)
Cables
HP X242 10G SFP+ to SFP+ 1m Direct Attach Copper Cable (J9281B)
HP X242 10G SFP+ to SFP+ 3m Direct Attach Copper Cable (J9283B)
HP X242 10G SFP+ to SFP+ 7m Direct Attach Copper Cable (J9285B)
HP X244 10G XFP to SFP+ 1m Direct Attach Copper Cable (J9300A)
HP X244 10G XFP to SFP+ 3m Direct Attach Copper Cable (J9301A)
HP X244 10G XFP to SFP+ 5m Direct Attach Copper Cable (J9302A)
HP 0.5 m Multimode OM3 LC/LC Optical Cable (AJ833A)
HP 1 m Multimode OM3 LC/LC Optical Cable (AJ834A)
HP 2 m Multimode OM3 LC/LC Optical Cable (AJ835A)
HP 5 m Multimode OM3 LC/LC Optical Cable (AJ836A)
HP 15 m Multimode OM3 LC/LC Optical Cable (AJ837A)
HP 30 m Multimode OM3 LC/LC Optical Cable (AJ838A)
HP 50 m Multimode OM3 LC/LC Optical Cable (AJ839A)
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 1m Cable (QK732A)
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 2m Cable (QK733A)
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 5m Cable (QK734A)
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 15m Cable (QK735A)
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 30m Cable (QK736A)
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 50m Cable (QK737A)
HP X242 10G SFP+ to SFP+ 10m Direct Attach Copper Cable (J9286B)
HP X242 10G SFP+ to SFP+ 15m Direct Attach Copper Cable (J9287B)
NEW HP X242 40G QSFP+ to QSFP+ 1m DAC Cable (JH234A)
NEW HP X242 40G QSFP+ to QSFP+ 3m DAC Cable (JH235A)
NEW HP X242 40G QSFP+ to QSFP+ 5m DAC Cable (JH236A)
Power supply
HP 5400R 700W PoE+ zl2 Power Supply (J9828A)
HP 5400R 1100W PoE+ zl2 Power Supply (J9829A)
HP 5400R 2750W PoE+ zl2 Power Supply (J9830A)
Mounting kit
HP X450 4U/7U Universal 4-Post Rack Mounting Kit (J9852A)
License
HP MSM Additional 40 Access Point License (J9371A)
HP MSM Additional 40 Access Point E-LTU (J9371AAE)
WLAN
HP MSM775 zl Premium Controller Module (J9840A)
Learn more at
hp.com/networking
Sign up for updates
hp.com/go/getupdated
Share with colleagues
Rate this document
© Copyright 2014–2015 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only
warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein
should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
ARM is a registered trademark of ARM Limited. SD is a trademark or registered trademark of SD-3C in the United States and other countries or both. sFlow
is a registered trademark of InMon Corp.
4AA5-2605ENW, April 2015, Rev. 3
Download PDF
Similar pages