Product
Folder
Sample &
Buy
Technical
Documents
Support &
Community
Tools &
Software
LM2576, LM2576HV
SNVS107D – JUNE 1999 – REVISED MAY 2016
LM2576xx Series SIMPLE SWITCHER® 3-A Step-Down Voltage Regulator
1 Features
3 Description
•
The LM2576 series of regulators are monolithic
integrated circuits that provide all the active functions
for a step-down (buck) switching regulator, capable of
driving 3-A load with excellent line and load
regulation. These devices are available in fixed output
voltages of 3.3 V, 5 V, 12 V, 15 V, and an adjustable
output version.
1
•
•
•
•
•
•
•
•
•
3.3-V, 5-V, 12-V, 15-V, and Adjustable Output
Versions
Adjustable Version Output Voltage Range,1.23 V
to 37 V (57 V for HV Version) ±4% Maximum Over
Line and Load Conditions
Specified 3-A Output Current
Wide Input Voltage Range: 40 V Up to 60 V for
HV Version
Requires Only 4 External Components
52-kHz Fixed-Frequency Internal Oscillator
TTL-Shutdown Capability, Low-Power Standby
Mode
High Efficiency
Uses Readily Available Standard Inductors
Thermal Shutdown and Current Limit Protection
2 Applications
•
•
•
•
Simple High-Efficiency Step-Down (Buck)
Regulator
Efficient Preregulator for Linear Regulators
On-Card Switching Regulators
Positive-to-Negative Converter (Buck-Boost)
Requiring a minimum number of external
components, these regulators are simple to use and
include fault protection and a fixed-frequency
oscillator.
The LM2576 series offers a high-efficiency
replacement for popular three-terminal linear
regulators. It substantially reduces the size of the
heat sink, and in some cases no heat sink is
required.
A standard series of inductors optimized for use with
the LM2576 are available from several different
manufacturers. This feature greatly simplifies the
design of switch-mode power supplies.
Other features include a ±4% tolerance on output
voltage within specified input voltages and output
load conditions, and ±10% on the oscillator
frequency. External shutdown is included, featuring
50-μA (typical) standby current. The output switch
includes cycle-by-cycle current limiting, as well as
thermal shutdown for full protection under fault
conditions.
Device Information(1)
PART NUMBER
LM2576
LM2576HV
PACKAGE
BODY SIZE (NOM)
TO-220 (5)
10.16 mm × 8.51 mm
DDPAK/TO-263 (5)
10.16 mm × 8.42 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Fixed Output Voltage Version Typical Application Diagram
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM2576, LM2576HV
SNVS107D – JUNE 1999 – REVISED MAY 2016
www.ti.com
Table of Contents
1
2
3
4
5
6
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
4
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
4
4
4
4
5
5
5
6
Absolute Maximum Ratings .....................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics: 3.3 V ................................
Electrical Characteristics: 5 V ...................................
Electrical Characteristics: 12 V .................................
Electrical Characteristics: 15 V .................................
Electrical Characteristics: Adjustable Output
Voltage .......................................................................
6.10 Electrical Characteristics: All Output Voltage
Versions .....................................................................
6.11 Typical Characteristics ............................................
7
6
6
8
Detailed Description ............................................ 12
7.1 Overview ................................................................. 12
7.2 Functional Block Diagram ....................................... 12
7.3 Feature Description................................................. 12
7.4 Device Functional Modes........................................ 14
8
Application and Implementation ........................ 15
8.1 Application Information............................................ 15
8.2 Typical Applications ................................................ 19
9 Power Supply Recommendations...................... 24
10 Layout................................................................... 25
10.1
10.2
10.3
10.4
Layout Guidelines .................................................
Layout Example ....................................................
Grounding .............................................................
Heat Sink and Thermal Considerations ................
25
26
26
26
11 Device and Documentation Support ................. 28
11.1
11.2
11.3
11.4
11.5
11.6
11.7
Device Support ....................................................
Documentation Suuport ........................................
Related Links ........................................................
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
28
29
29
29
29
29
29
12 Mechanical, Packaging, and Orderable
Information ........................................................... 30
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision C (April 2013) to Revision D
Page
•
Added ESD Ratings table, Feature Description section, Device Functional Modes, Application and Implementation
section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and
Mechanical, Packaging, and Orderable Information section. ................................................................................................. 1
•
Moved the thermal resistance data from the Electrical Characteristics: All Output Voltage Versions table to the
Thermal Information table....................................................................................................................................................... 4
Changes from Revision B (April 2013) to Revision C
•
2
Page
Changed layout of National Data Sheet to TI format ............................................................................................................. 3
Submit Documentation Feedback
Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
LM2576, LM2576HV
www.ti.com
SNVS107D – JUNE 1999 – REVISED MAY 2016
5 Pin Configuration and Functions
KC Package
5-Pin TO-220
Top View
KTT Package
5-PIN DDPAK/TO-263
Top View
DDPAK/TO-263 (S) Package
5-Lead Surface-Mount Package
Top View
Pin Functions
PIN
NO.
NAME
I/O (1)
DESCRIPTION
1
VIN
I
Supply input pin to collector pin of high-side transistor. Connect to power supply and input
bypass capacitors CIN. Path from VIN pin to high frequency bypass CIN and GND must be as
short as possible.
2
OUTPUT
O
Emitter pin of the power transistor. This is a switching node. Attached this pin to an inductor
and the cathode of the external diode.
3
GROUND
—
Ground pin. Path to CIN must be as short as possible.
4
FEEDBACK
I
Feedback sense input pin. Connect to the midpoint of feedback divider to set VOUT for ADJ
version or connect this pin directly to the output capacitor for a fixed output version.
5
ON/OFF
I
Enable input to the voltage regulator. High = OFF and low = ON. Connect to GND to enable
the voltage regulator. Do not leave this pin float.
—
TAB
—
(1)
Connected to GND. Attached to heatsink for thermal relief for TO-220 package or put a
copper plane connected to this pin as a thermal relief for DDPAK package.
I = INPUT, O = OUTPUT
Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
Submit Documentation Feedback
3
LM2576, LM2576HV
SNVS107D – JUNE 1999 – REVISED MAY 2016
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over the recommended operating junction temperature range of -40°C to 125°C (unless otherwise noted) (1) (2)
MIN
Maximum supply voltage
45
LM2576HV
63
ON /OFF pin input voltage
Output voltage to ground
MAX
LM2576
(Steady-state)
Power dissipation
V
−1
V
Internally Limited
−65
Storage temperature, Tstg
(2)
V
−0.3V ≤ V ≤ +VIN
Maximum junction temperature, TJ
(1)
UNIT
150
°C
150
°C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
If Military/Aerospace specified devices are required, please contact the TI Sales Office/ Distributors for availability and specifications.
6.2 ESD Ratings
V(ESD)
(1)
Electrostatic discharge
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001
(1)
VALUE
UNIT
±2000
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over the recommended operating junction temperature range of -40°C to 125°C (unless otherwise noted)
Temperature
LM2576, LM2576HV
Supply voltage
MIN
MAX
UNIT
−40
125
°C
LM2576
40
LM2576HV
60
V
6.4 Thermal Information
LM2576, LM2576HV
THERMAL METRIC (1) (2) (3)
KTT (TO-263)
KC (TO-220)
UNIT
5 PINS
5 PINS
RθJA
Junction-to-ambient thermal resistance
42.6
32.4
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
43.3
41.2
°C/W
RθJB
Junction-to-board thermal resistance
22.4
17.6
°C/W
ψJT
Junction-to-top characterization parameter
10.7
7.8
°C/W
ψJB
Junction-to-board characterization parameter
21.3
17
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
0.4
0.4
°C/W
(1)
(2)
(3)
4
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953 and the Using New Thermal Metrics applications report, SBVA025.
The package thermal impedance is calculated in accordance with JESD 51-7
Thermal Resistances were simulated on a 4-layer, JEDEC board.
Submit Documentation Feedback
Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
LM2576, LM2576HV
www.ti.com
SNVS107D – JUNE 1999 – REVISED MAY 2016
6.5 Electrical Characteristics: 3.3 V
Specifications are for TJ = 25°C (unless otherwise noted).
PARAMETER
TEST CONDITIONS
SYSTEM PARAMETERS TEST CIRCUIT Figure 26 and Figure 32
(1)
TYP
MAX
UNIT
3.234
3.3
3.366
V
3.3
3.432
Output Voltage
VIN = 12 V, ILOAD = 0.5 A
Circuit of Figure 26 and Figure 32
TJ = 25°C
3.168
Output Voltage: LM2576
6 V ≤ VIN ≤ 40 V, 0.5 A ≤
ILOAD ≤ 3 A
Circuit of Figure 26 and
Figure 32
Applies over full
operating
temperature range
3.135
TJ = 25°C
3.168
Output Voltage: LM2576HV
6 V ≤ VIN ≤ 60 V, 0.5 A ≤
ILOAD ≤ 3 A
Circuit of Figure 26 and
Figure 32
Applies over full
operating
temperature range
3.135
Efficiency
VIN = 12 V, ILOAD = 3 A
VOUT
η
MIN
(1)
3.465
3.3
V
3.45
3.482
V
75%
External components such as the catch diode, inductor, input and output capacitors can affect switching regulator system performance.
When the LM2576/LM2576HV is used as shown in Figure 26 and Figure 32, system performance is as shown in Electrical
Characteristics: All Output Voltage Versions.
6.6 Electrical Characteristics: 5 V
Specifications are for TJ = 25°C for the Figure 26 and Figure 32 (unless otherwise noted).
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
4.9
5
5.1
4.8
5
5.2
UNIT
SYSTEM PARAMETERS TEST CIRCUIT Figure 26 and Figure 32 (1)
VOUT
Output Voltage
VIN = 12 V, ILOAD = 0.5 A
Circuit of Figure 26 and Figure 32
VOUT
0.5 A ≤ ILOAD ≤ 3 A,
8 V ≤ VIN ≤ 40 V
Circuit of Figure 26 and
Figure 32
TJ = 25°C
Output Voltage
LM2576
VOUT
0.5 A ≤ ILOAD ≤ 3 A,
8 V ≤ VIN ≤ 60 V
Circuit of Figure 26 and
Figure 32
TJ = 25°C
Output Voltage
LM2576HV
η
Efficiency
VIN = 12 V, ILOAD = 3 A
(1)
Applies over full
operating
temperature range
Applies over full
operating
temperature range
4.75
4.8
5.25
5
5.225
V
V
4.75
5.275
V
77%
External components such as the catch diode, inductor, input and output capacitors can affect switching regulator system performance.
When the LM2576/LM2576HV is used as shown in Figure 26 and Figure 32, system performance is as shown in Electrical
Characteristics: All Output Voltage Versions.
6.7 Electrical Characteristics: 12 V
Specifications are for TJ = 25°C (unless otherwise noted).
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
11.76
12
12.24
V
11.52
12
12.48
SYSTEM PARAMETERS TEST CIRCUIT Figure 26 and Figure 32 (1)
VOUT
Output Voltage
VIN = 25 V, ILOAD = 0.5 A
Circuit of Figure 26 and Figure 32
VOUT
0.5 A ≤ ILOAD ≤ 3 A,
15 V ≤ VIN ≤ 40 V
Circuit of Figure 26 and
Figure 32 and
TJ = 25°C
Output Voltage
LM2576
VOUT
0.5 A ≤ ILOAD ≤ 3 A,
15 V ≤ VIN ≤ 60 V
Circuit of Figure 26 and
Figure 32
TJ = 25°C
Output Voltage
LM2576HV
η
Efficiency
VIN = 15 V, ILOAD = 3 A
(1)
Applies over full
operating
temperature range
Applies over full
operating
temperature range
11.4
11.52
12.6
12
11.4
V
12.54
12.66
V
88%
External components such as the catch diode, inductor, input and output capacitors can affect switching regulator system performance.
When the LM2576/LM2576HV is used as shown in Figure 26 and Figure 32, system performance is as shown in Electrical
Characteristics: All Output Voltage Versions.
Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
Submit Documentation Feedback
5
LM2576, LM2576HV
SNVS107D – JUNE 1999 – REVISED MAY 2016
www.ti.com
6.8 Electrical Characteristics: 15 V
over operating free-air temperature range (unless otherwise noted).
PARAMETER
TEST CONDITIONS
SYSTEM PARAMETERS TEST CIRCUIT Figure 26 and Figure 32
VOUT
Output Voltage
VIN = 25 V, ILOAD = 0.5 A
Circuit of Figure 26 and Figure 32
VOUT
0.5 A ≤ ILOAD ≤ 3 A,
18 V ≤ VIN ≤ 40 V
Circuit of Figure 26 and
Figure 32
TJ = 25°C
Output Voltage
LM2576
VOUT
0.5 A ≤ ILOAD ≤ 3 A,
18 V ≤ VIN ≤ 60 V
Circuit of Figure 26 and
Figure 32
TJ = 25°C
Output Voltage
LM2576HV
η
Efficiency
VIN = 18 V, ILOAD = 3 A
(1)
MIN
TYP
MAX
UNIT
14.7
15
15.3
V
14.4
15
15.6
(1)
Applies over full
operating
temperature range
14.25
15.75
14.4
Applies over full
operating
temperature range
15
15.68
V
14.25
15.83
V
88%
External components such as the catch diode, inductor, input and output capacitors can affect switching regulator system performance.
When the LM2576/LM2576HV is used as shown in Figure 26 and Figure 32, system performance is as shown in Electrical
Characteristics: All Output Voltage Versions.
6.9 Electrical Characteristics: Adjustable Output Voltage
over operating free-air temperature range (unless otherwise noted).
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
1.217
1.23
1.243
V
1.193
1.23
1.267
SYSTEM PARAMETERS TEST CIRCUIT Figure 26 and Figure 32 (1)
VOUT
Feedback voltage
VIN = 12 V, ILOAD = 0.5 A
VOUT = 5 V,
Circuit of Figure 26 and Figure 32
VOUT
0.5 A ≤ ILOAD ≤ 3 A,
8 V ≤ VIN ≤ 40 V
VOUT = 5 V, Circuit of
Figure 26 and Figure 32
TJ = 25°C
Feedback Voltage
LM2576
VOUT
0.5 A ≤ ILOAD ≤ 3 A,
8 V ≤ VIN ≤ 60 V
VOUT = 5 V, Circuit of
Figure 26 and Figure 32
TJ = 25°C
Feedback Voltage
LM2576HV
η
Efficiency
VIN = 12 V, ILOAD = 3 A, VOUT = 5 V
(1)
Applies over full
operating
temperature range
1.18
1.193
Applies over full
operating
temperature range
1.28
1.23
1.18
V
1.273
1.286
V
77%
External components such as the catch diode, inductor, input and output capacitors can affect switching regulator system performance.
When the LM2576/LM2576HV is used as shown in Figure 26 and Figure 32, system performance is as shown in Electrical
Characteristics: All Output Voltage Versions.
6.10 Electrical Characteristics: All Output Voltage Versions
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
SYSTEM PARAMETERS TEST CIRCUIT Figure 26 and Figure 32
Ib
Feedback Bias Current
fO
Oscillator Frequency (3)
(1)
(2)
(3)
6
VOUT = 5 V (Adjustable
Version Only)
MIN
TYP (1)
MAX
UNIT
(2)
TJ = 25°C
100
Applies over full
operating
temperature range
500
TJ = 25°C
47
Applies over full operating temperature range
42
50
nA
52
58
63
kHz
All limits specified at room temperature (25°C) unless otherwise noted. All room temperature limits are 100% production tested. All limits
at temperature extremes are specified through correlation using standard Statistical Quality Control (SQC) methods.
External components such as the catch diode, inductor, input and output capacitors can affect switching regulator system performance.
When the LM2576/LM2576HV is used as shown in Figure 26 and Figure 32, system performance is as shown in Electrical
Characteristics: All Output Voltage Versions.
The oscillator frequency reduces to approximately 11 kHz in the event of an output short or an overload which causes the regulated
output voltage to drop approximately 40% from the nominal output voltage. This self protection feature lowers the average power
dissipation of the IC by lowering the minimum duty cycle from 5% down to approximately 2%.
Submit Documentation Feedback
Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
LM2576, LM2576HV
www.ti.com
SNVS107D – JUNE 1999 – REVISED MAY 2016
Electrical Characteristics: All Output Voltage Versions (continued)
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TJ = 25°C
VSAT
Saturation Voltage
DC
Max Duty Cycle (ON) (5)
ICL
Current Limit (4) (3)
IL
Output Leakage Current
IQ
Quiescent Current (6)
ISTBY
Standby Quiescent
Current
IOUT = 3 A
TYP (1)
MAX
1.4
Applies over full
operating
temperature range
(4)
93%
98%
4.2
5.8
Applies over full operating temperature range
3.5
Output = 0 V
Output = −1 V
Output = −1 V
2
(6) (7)
1.8
2
TJ = 25°C
ON /OFF Pin = 5 V (OFF)
UNIT
6.9
7.5
V
A
7.5
30
mA
5
10
mA
50
200
μA
ON /OFF CONTROL TEST CIRCUIT Figure 26 and Figure 32
VOUT = 0 V
VIH
ON /OFF Pin
Logic Input Level
VIL
IIH
IIL
(4)
(5)
(6)
(7)
ON /OFF Pin Input
Current
VOUT = Nominal Output
Voltage
TJ = 25°C
2.2
Applies over full
operating
temperature range
2.4
TJ = 25°C
1.4
V
1.2
Applies over full
operating
temperature range
1
0.8
V
ON /OFF Pin = 5 V (OFF)
12
30
μA
ON /OFF Pin = 0 V (ON)
0
10
μA
Output pin sourcing current. No diode, inductor or capacitor connected to output.
Feedback pin removed from output and connected to 0V.
Feedback pin removed from output and connected to +12 V for the Adjustable, 3.3-V, and 5-V versions, and +25 V for the 12-V and 15V versions, to force the output transistor OFF.
VIN = 40 V (60 V for high voltage version).
Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
Submit Documentation Feedback
7
LM2576, LM2576HV
SNVS107D – JUNE 1999 – REVISED MAY 2016
www.ti.com
6.11 Typical Characteristics
(Circuit of Figure 26 and Figure 32)
8
Figure 1. Normalized Output Voltage
Figure 2. Line Regulation
Figure 3. Dropout Voltage
Figure 4. Current Limit
Figure 5. Quiescent Current
Figure 6. Standby Quiescent Current
Submit Documentation Feedback
Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
LM2576, LM2576HV
www.ti.com
SNVS107D – JUNE 1999 – REVISED MAY 2016
Typical Characteristics (continued)
(Circuit of Figure 26 and Figure 32)
Figure 7. Oscillator Frequency
Figure 8. Switch Saturation Voltage
Figure 10. Minimum Operating Voltage
Figure 9. Efficiency
Figure 11. Quiescent Current vs Duty Cycle
Figure 12. Feedback Voltage vs Duty Cycle
Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
Submit Documentation Feedback
9
LM2576, LM2576HV
SNVS107D – JUNE 1999 – REVISED MAY 2016
www.ti.com
Typical Characteristics (continued)
(Circuit of Figure 26 and Figure 32)
Figure 13. Minimum Operating Voltage
Figure 14. Quiescent Current vs Duty Cycle
Figure 15. Feedback Voltage vs Duty Cycle
Figure 16. Feedback Pin Current
VOUT = 15 V
A: Output Pin Voltage, 50 V/div
B: Output Pin Current, 2 A/div
If the DDPAK/TO-263 package is used, the thermal resistance can be
C: Inductor Current, 2 A/div
reduced by increasing the PCB copper area thermally connected to
the package. Using 0.5 square inches of copper area, θJA is 50°C/W, D: Output Ripple Voltage, 50 mV/div,
AC-Coupled
with 1 square inch of copper area, θJA is 37°C/W, and with 1.6 or
Horizontal Time Base: 5 μs/div
more square inches of copper area, θJA is 32°C/W.
Figure 18. Switching Waveforms
Figure 17. Maximum Power Dissipation (DDPAK/TO-263)
10
Submit Documentation Feedback
Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
LM2576, LM2576HV
www.ti.com
SNVS107D – JUNE 1999 – REVISED MAY 2016
Typical Characteristics (continued)
(Circuit of Figure 26 and Figure 32)
Figure 19. Load Transient Response
Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
Submit Documentation Feedback
11
LM2576, LM2576HV
SNVS107D – JUNE 1999 – REVISED MAY 2016
www.ti.com
7 Detailed Description
7.1 Overview
The LM2576 SIMPLE SWITCHER® regulator is an easy-to-use, non-synchronous step-down DC-DC converter
with a wide input voltage range from 40 V to up to 60 V for a HV version. It is capable of delivering up to 3-A DC
load current with excellent line and load regulation. These devices are available in fixed output voltages of 3.3 V,
5 V, 12 V, 15 V, and an adjustable output version. The family requires few external components, and the pin
arrangement was designed for simple, optimum PCB layout.
7.2 Functional Block Diagram
3.3 V R2 = 1.7 k
5 V, R2 = 3.1 k
12 V, R2 = 8.84 k
15 V, R2 = 11.3 k
For ADJ. Version
R1 = Open, R2 = 0 Ω
Patent Pending
7.3 Feature Description
7.3.1 Undervoltage Lockout
In some applications it is desirable to keep the regulator off until the input voltage reaches a certain threshold.
Figure 20 shows an undervoltage lockout circuit that accomplishes this task, while Figure 21 shows the same
circuit applied to a buck-boost configuration. These circuits keep the regulator off until the input voltage reaches
a predetermined level.
VTH ≈ VZ1 + 2VBE(Q1)
12
Submit Documentation Feedback
(1)
Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
LM2576, LM2576HV
www.ti.com
SNVS107D – JUNE 1999 – REVISED MAY 2016
Feature Description (continued)
Complete circuit not shown.
Figure 20. Undervoltage Lockout for Buck Circuit
Complete circuit not shown (see Figure 24).
Figure 21. Undervoltage Lockout
for Buck-Boost Circuit
7.3.2 Delayed Start-Up
The ON /OFF pin can be used to provide a delayed start-up feature as shown in Figure 22. With an input voltage
of 20 V and for the part values shown, the circuit provides approximately 10 ms of delay time before the circuit
begins switching. Increasing the RC time constant can provide longer delay times. But excessively large RC time
constants can cause problems with input voltages that are high in 60-Hz or 120-Hz ripple, by coupling the ripple
into the ON /OFF pin.
7.3.3 Adjustable Output, Low-Ripple Power Supply
Figure 23 shows a 3-A power supply that features an adjustable output voltage. An additional LC filter that
reduces the output ripple by a factor of 10 or more is included in this circuit.
Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
Submit Documentation Feedback
13
LM2576, LM2576HV
SNVS107D – JUNE 1999 – REVISED MAY 2016
www.ti.com
Feature Description (continued)
Complete circuit not shown.
Figure 22. Delayed Start-Up
Figure 23. 1.2-V to 55-V Adjustable 3-A Power Supply With Low Output Ripple
7.4 Device Functional Modes
7.4.1 Shutdown Mode
The ON/OFF pin provides electrical ON and OFF control for the LM2576. When the voltage of this pin is higher
than 1.4 V, the device is in shutdown mode. The typical standby current in this mode is 50 μA.
7.4.2 Active Mode
When the voltage of the ON/OFF pin is below 1.2 V, the device starts switching, and the output voltage rises until
it reaches the normal regulation voltage.
7.4.3 Current Limit
The LM2576 device has current limiting to prevent the switch current from exceeding safe values during an
accidental overload on the output. This current limit value can be found in Electrical Characteristics: All Output
Voltage Versions under the heading of ICL.
The LM2576 uses cycle-by-cycle peak current limit for overload protection. This helps to prevent damage to the
device and external components. The regulator operates in current limit mode whenever the inductor current
exceeds the value of ICL given in Electrical Characteristics: All Output Voltage Versions. This occurs if the load
current is greater than 3 A, or the converter is starting up. Keep in mind that the maximum available load current
depends on the input voltage, output voltage, and inductor value. The regulator also incorporates short-circuit
protection to prevent inductor current run-away. When the voltage on the FB pin (ADJ) falls below about 0.58 V
the switching frequency is dropped to about 11 kHz. This allows the inductor current to ramp down sufficiently
during the switch OFF-time to prevent saturation.
14
Submit Documentation Feedback
Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
LM2576, LM2576HV
www.ti.com
SNVS107D – JUNE 1999 – REVISED MAY 2016
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
8.1.1 Input Capacitor (CIN)
To maintain stability, the regulator input pin must be bypassed with at least a 100-μF electrolytic capacitor. The
capacitor's leads must be kept short, and placed near the regulator.
If the operating temperature range includes temperatures below −25°C, the input capacitor value may need to be
larger. With most electrolytic capacitors, the capacitance value decreases and the ESR increases with lower
temperatures and age. Paralleling a ceramic or solid tantalum capacitor increases the regulator stability at cold
temperatures. For maximum capacitor operating lifetime, the RMS ripple current rating of the capacitor must be
greater than:
(2)
8.1.2 Inductor Selection
All switching regulators have two basic modes of operation: continuous and discontinuous. The difference
between the two types relates to the inductor current, whether it is flowing continuously, or if it drops to zero for a
period of time in the normal switching cycle. Each mode has distinctively different operating characteristics,
which can affect the regulator performance and requirements.
The LM2576 (or any of the SIMPLE SWITCHER® family can be used for both continuous and discontinuous
modes of operation.
The inductor value selection guides in Figure 27 through Figure 31 are designed for buck regulator designs of
the continuous inductor current type. When using inductor values shown in the inductor selection guide, the
peak-to-peak inductor ripple current is approximately 20% to 30% of the maximum DC current. With relatively
heavy load currents, the circuit operates in the continuous mode (inductor current always flowing), but under light
load conditions, the circuit is forced to the discontinuous mode (inductor current falls to zero for a period of time).
This discontinuous mode of operation is perfectly acceptable. For light loads (less than approximately 300 mA), it
may be desirable to operate the regulator in the discontinuous mode, primarily because of the lower inductor
values required for the discontinuous mode.
The selection guide chooses inductor values suitable for continuous mode operation, but if the inductor value
chosen is prohibitively high, the designer should investigate the possibility of discontinuous operation.
Inductors are available in different styles such as pot core, toriod, E-frame, bobbin core, and so on, as well as
different core materials, such as ferrites and powdered iron. The bobbin core is the least expensive type, and
consists of wire wrapped on a ferrite rod core. This type of construction makes for an inexpensive inductor;
however, because the magnetic flux is not completely contained within the core, the bobbin core generates more
electromagnetic interference (EMI). This EMI can cause problems in sensitive circuits, or can give incorrect
scope readings because of induced voltages in the scope probe.
The inductors listed in the selection chart include ferrite pot core construction for AIE, powdered iron toroid for
Pulse Engineering, and ferrite bobbin core for Renco.
Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
Submit Documentation Feedback
15
LM2576, LM2576HV
SNVS107D – JUNE 1999 – REVISED MAY 2016
www.ti.com
Application Information (continued)
An inductor must not operate beyond its maximum-rated current because it may saturate. When an inductor
begins to saturate, the inductance decreases rapidly, and the inductor begins to look mainly resistive (the DC
resistance of the winding), causing the switch current to rise very rapidly. Different inductor types have different
saturation characteristics, and this must be considered when selecting an inductor.
The inductor manufacturer's data sheets include current and energy limits to avoid inductor saturation.
8.1.3 Inductor Ripple Current
When the switcher is operating in the continuous mode, the inductor current waveform ranges from a triangular
to a sawtooth type of waveform (depending on the input voltage). For a given input voltage and output voltage,
the peak-to-peak amplitude of this inductor current waveform remains constant. As the load current rises or falls,
the entire sawtooth current waveform also rises or falls. The average DC value of this waveform is equal to the
DC load current (in the buck regulator configuration).
If the load current drops to a low enough level, the bottom of the sawtooth current waveform reaches zero, and
the switcher changes to a discontinuous mode of operation. This is a perfectly acceptable mode of operation.
Any buck switching regulator (no matter how large the inductor value is) is forced to run discontinuous if the load
current is light enough.
8.1.4 Output Capacitor
An output capacitor is required to filter the output voltage and is needed for loop stability. The capacitor must be
placed near the LM2576 using short PCB traces. Standard aluminum electrolytics are usually adequate, but TI
recommends low ESR types for low output ripple voltage and good stability. The ESR of a capacitor depends on
many factors, including: the value, the voltage rating, physical size, and the type of construction. In general, low
value or low voltage (less than 12 V) electrolytic capacitors usually have higher ESR numbers.
The amount of output ripple voltage is primarily a function of the ESR (Equivalent Series Resistance) of the
output capacitor and the amplitude of the inductor ripple current (ΔIIND). See Inductor Ripple Current.
The lower capacitor values (220 μF to 1000 μF) allows typically 50 mV to 150 mV of output ripple voltage, while
larger-value capacitors reduces the ripple to approximately 20 mV to 50 mV.
Output Ripple Voltage = (ΔIIND) (ESR of COUT)
(3)
To further reduce the output ripple voltage, several standard electrolytic capacitors may be paralleled, or a
higher-grade capacitor may be used. Such capacitors are often called high-frequency, low-inductance, or lowESR. These reduces the output ripple to 10 mV or 20 mV. However, when operating in the continuous mode,
reducing the ESR below 0.03 Ω can cause instability in the regulator.
Tantalum capacitors can have a very low ESR, and must be carefully evaluated if it is the only output capacitor.
Because of their good low temperature characteristics, a tantalum can be used in parallel with aluminum
electrolytics, with the tantalum making up 10% or 20% of the total capacitance.
The ripple current rating of the capacitor at 52 kHz should be at least 50% higher than the peak-to-peak inductor
ripple current.
8.1.5 Catch Diode
Buck regulators require a diode to provide a return path for the inductor current when the switch is off. This diode
must be placed close to the LM2576 using short leads and short printed-circuit traces.
Because of their fast switching speed and low forward voltage drop, Schottky diodes provide the best efficiency,
especially in low output voltage switching regulators (less than 5 V). Fast-recovery, high-efficiency, or ultra-fast
recovery diodes are also suitable, but some types with an abrupt turnoff characteristic may cause instability and
EMI problems. A fast-recovery diode with soft recovery characteristics is a better choice. Standard 60-Hz diodes
(for example, 1N4001 or 1N5400, and so on) are also not suitable. See Table 3 for Schottky and soft fastrecovery diode selection guide.
16
Submit Documentation Feedback
Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
LM2576, LM2576HV
www.ti.com
SNVS107D – JUNE 1999 – REVISED MAY 2016
Application Information (continued)
8.1.6 Output Voltage Ripple and Transients
The output voltage of a switching power supply contains a sawtooth ripple voltage at the switcher frequency,
typically about 1% of the output voltage, and may also contain short voltage spikes at the peaks of the sawtooth
waveform.
The output ripple voltage is due mainly to the inductor sawtooth ripple current multiplied by the ESR of the output
capacitor (see Inductor Selection).
The voltage spikes are present because of the fast switching action of the output switch, and the parasitic
inductance of the output filter capacitor. To minimize these voltage spikes, special low inductance capacitors can
be used, and their lead lengths must be kept short. Wiring inductance, stray capacitance, as well as the scope
probe used to evaluate these transients, all contribute to the amplitude of these spikes.
An additional small LC filter (20 μH and 100 μF) can be added to the output (as shown in Figure 23) to further
reduce the amount of output ripple and transients. A 10 × reduction in output ripple voltage and transients is
possible with this filter.
8.1.7 Feedback Connection
The LM2576 (fixed voltage versions) feedback pin must be wired to the output voltage point of the switching
power supply. When using the adjustable version, physically locate both output voltage programming resistors
near the LM2576 to avoid picking up unwanted noise. Avoid using resistors greater than 100 kΩ because of the
increased chance of noise pickup.
8.1.8 ON /OFF INPUT
For normal operation, the ON /OFF pin must be grounded or driven with a low-level TTL voltage (typically below
1.6 V). To put the regulator into standby mode, drive this pin with a high-level TTL or CMOS signal. The ON
/OFF pin can be safely pulled up to +VIN without a resistor in series with it. The ON /OFF pin must not be left
open.
8.1.9 Inverting Regulator
Figure 24 shows a LM2576-12 in a buck-boost configuration to generate a negative 12-V output from a positive
input voltage. This circuit bootstraps the ground pin of the regulator to the negative output voltage, then by
grounding the feedback pin, the regulator senses the inverted output voltage and regulates it to −12 V.
For an input voltage of 12 V or more, the maximum available output current in this configuration is approximately
700 mA. At lighter loads, the minimum input voltage required drops to approximately 4.7 V.
The switch currents in this buck-boost configuration are higher than in the standard buck-mode design, thus
lowering the available output current. Also, the start-up input current of the buck-boost converter is higher than
the standard buck-mode regulator, and this may overload an input power source with a current limit less than
5 A. Using a delayed turn-on or an undervoltage lockout circuit (described in Negative Boost Regulator) would
allow the input voltage to rise to a high enough level before the switcher would be allowed to turn on.
Because of the structural differences between the buck and the buck-boost regulator topologies, the buck
regulator design procedure section can not be used to select the inductor or the output capacitor. The
recommended range of inductor values for the buck-boost design is between 68 μH and 220 μH, and the output
capacitor values must be larger than what is normally required for buck designs. Low input voltages or high
output currents require a large value output capacitor (in the thousands of micro Farads).
The peak inductor current, which is the same as the peak switch current, can be calculated in Equation 4:
where
•
fosc = 52 kHz
(4)
Under normal continuous inductor current operating conditions, the minimum VIN represents the worst case.
Select an inductor that is rated for the peak current anticipated.
Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
Submit Documentation Feedback
17
LM2576, LM2576HV
SNVS107D – JUNE 1999 – REVISED MAY 2016
www.ti.com
Application Information (continued)
Figure 24. Inverting Buck-Boost Develops −12 V
Also, the maximum voltage appearing across the regulator is the absolute sum of the input and output voltage.
For a −12-V output, the maximum input voltage for the LM2576 is +28 V, or +48 V for the LM2576HV.
8.1.10 Negative Boost Regulator
Another variation on the buck-boost topology is the negative boost configuration. The circuit in Figure 25 accepts
an input voltage ranging from −5 V to −12 V and provides a regulated −12-V output. Input voltages greater than
−12 V causes the output to rise above −12 V, but does not damage the regulator.
+
Feedback
VIN
1
LM2576-12
COUT
4
Output
2200 PF
LOW ESR
2
+
CIN
3
GND
5
ON/OFF
1N5820
100 PF
-VIN
VOUT = -12V
100 PH
-5V to -12V
Copyright © 2016, Texas Instruments Incorporated
Typical Load Current
400 mA for VIN = −5.2 V
750 mA for VIN = −7 V
Heat sink may be required.
Figure 25. Negative Boost
Because of the boosting function of this type of regulator, the switch current is relatively high, especially at low
input voltages. Output load current limitations are a result of the maximum current rating of the switch. Also,
boost regulators can not provide current-limiting load protection in the event of a shorted load, so some other
means (such as a fuse) may be necessary.
18
Submit Documentation Feedback
Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
LM2576, LM2576HV
www.ti.com
SNVS107D – JUNE 1999 – REVISED MAY 2016
8.2 Typical Applications
8.2.1 Fixed Output Voltage Version
CIN — 100-μF, 75-V, Aluminum Electrolytic
COUT — 1000-μF, 25-V, Aluminum Electrolytic
D1 — Schottky, MBR360
L1 — 100 μH, Pulse Eng. PE-92108
R1 — 2 k, 0.1%
R2 — 6.12 k, 0.1%
Figure 26. Fixed Output Voltage Versions
8.2.1.1 Design Requirements
Table 1 lists the design parameters of this example.
Table 1. Design Parameters
DESIGN PARAMETER
Regulated Output Voltage
EXAMPLE VALUE
5V
(3.3 V, 5 V, 12 V, or 15 V), VOUT
Maximum Input Voltage, VIN(Max)
15 V
Maximum Load Current,
ILOAD(Max)
3A
8.2.1.2 Detailed Design Procedure
8.2.1.2.1 Inductor Selection (L1)
1. Select the correct Inductor value selection guide from Figure 27, Figure 28, Figure 29, or Figure 30. (Output
voltages of 3.3 V, 5 V, 12 V or 15 V respectively). For other output voltages, see the design procedure for the
adjustable version. Use the selection guide shown in Figure 28.
2. From the inductor value selection guide, identify the inductance region intersected by VIN(Max) and
ILOAD(Max), and note the inductor code for that region. From the selection guide, the inductance area
intersected by the 15-V line and 3-A line is L100.
3. Identify the inductor value from the inductor code, and select an appropriate inductor from the table shown in
Figure 27. Part numbers are listed for three inductor manufacturers. The inductor chosen must be rated for
operation at the LM2576 switching frequency (52 kHz) and for a current rating of 1.15 × ILOAD. For additional
inductor information, see Inductor Selection. Inductor value required is 100 μH from the table in Figure 27.
Choose AIE 415-0930, Pulse Engineering PE92108, or Renco RL2444.
8.2.1.2.2 Output Capacitor Selection (COUT)
1. The value of the output capacitor together with the inductor defines the dominate pole-pair of the switching
regulator loop. For stable operation and an acceptable output ripple voltage, (approximately 1% of the output
voltage) TI recommends a value between 100 μF and 470 μF. We choose COUT = 680-μF to 2000-μF
standard aluminum electrolytic.
Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
Submit Documentation Feedback
19
LM2576, LM2576HV
SNVS107D – JUNE 1999 – REVISED MAY 2016
www.ti.com
2. The voltage rating of the capacitor must be at least 1.5 times greater than the output voltage. For a 5-V
regulator, a rating of at least 8 V is appropriate, and a 10-V or 15-V rating is recommended. Capacitor
voltage rating = 20 V. Higher voltage electrolytic capacitors generally have lower ESR numbers, and for this
reason it may be necessary to select a capacitor rated for a higher voltage than would normally be needed.
8.2.1.2.3 Catch Diode Selection (D1)
1. The catch-diode current rating must be at least 1.2 times greater than the maximum load current. Also, if the
power supply design must withstand a continuous output short, the diode should have a current rating equal
to the maximum current limit of the LM2576. The most stressful condition for this diode is an overload or
shorted output condition. For this example, a 3-A current rating is adequate.
2. The reverse voltage rating of the diode should be at least 1.25 times the maximum input voltage. Use a 20-V
1N5823 or SR302 Schottky diode, or any of the suggested fast-recovery diodes shown in Table 3.
8.2.1.2.4 Input Capacitor (CIN)
An aluminum or tantalum electrolytic bypass capacitor located close to the regulator is needed for stable
operation. A 100-μF, 25-V aluminum electrolytic capacitor located near the input and ground pins provides
sufficient bypassing.
8.2.1.3 Application Curves
20
Figure 27. LM2576(HV)-3.3
Figure 28. LM2576(HV)-5.0
Figure 29. LM2576(HV)-12
Figure 30. LM2576(HV)-15
Submit Documentation Feedback
Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
LM2576, LM2576HV
www.ti.com
SNVS107D – JUNE 1999 – REVISED MAY 2016
Figure 31. LM2576(HV)-ADJ
8.2.2 Adjusted Output Voltage Version
where
VREF = 1.23 V, R1 between 1 k and 5 k
Figure 32. Adjustable Output Voltage Version
8.2.2.1 Design Requirements
Table 2 lists the design parameters of this example.
Table 2. Design Parameters
DESIGN PARAMETER
EXAMPLE VALUE
Regulated Output Voltage, VOUT
10 V
Maximum Input Voltage, VIN(Max)
25 V
Maximum Load Current,
ILOAD(Max)
3A
Switching Frequency, F
Fixed at 52 kHz
Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
Submit Documentation Feedback
21
LM2576, LM2576HV
SNVS107D – JUNE 1999 – REVISED MAY 2016
www.ti.com
8.2.2.2 Detailed Design Procedure
8.2.2.2.1 Programming Output Voltage
Select R1 and R2, as shown in Figure 32.
Use Equation 5 to select the appropriate resistor values.
(5)
R1 can be between 1k and 5k. (For best temperature coefficient and stability with time, use 1% metal film
resistors)
(6)
(7)
R2 = 1 k (8.13 − 1) = 7.13 k, closest 1% value is 7.15 k
8.2.2.2.2 Inductor Selection (L1)
1. Calculate the inductor Volt • microsecond constant, E • T (V • μs), from Equation 8:
(8)
Calculate E • T (V • μs)
(9)
2. Use the E • T value from the previous formula and match it with the E • T number on the vertical axis of the
Inductor value selection guide shown in Figure 31.
E • T = 115 V • μs
3. On the horizontal axis, select the maximum load current.
ILOAD(Max) = 3 A
4. Identify the inductance region intersected by the E • T value and the maximum load current value, and note
the inductor code for that region.
Inductance Region = H150
5. Identify the inductor value from the inductor code, and select an appropriate inductor from the table shown in
Table 4. Part numbers are listed for three inductor manufacturers. The inductor chosen must be rated for
operation at the LM2576 switching frequency (52 kHz) and for a current rating of 1.15 × ILOAD. For additional
inductor information, see Inductor Selection.
Inductor Value = 150 μH
Choose from AIE part #415-0936, Pulse Engineering part #PE-531115, or Renco part #RL2445.
8.2.2.2.3 Output Capacitor Selection (COUT)
1. The value of the output capacitor together with the inductor defines the dominate pole-pair of the switching
regulator loop. For stable operation, the capacitor must satisfy :
yields capacitor values between 10 μF and 2200 μF that satisfies the loop requirements for stable operation.
But to achieve an acceptable output ripple voltage, (approximately 1% of the output voltage) and transient
response, the output capacitor may need to be several times larger than yields.
However, for acceptable output ripple voltage select
22
Submit Documentation Feedback
Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
LM2576, LM2576HV
www.ti.com
SNVS107D – JUNE 1999 – REVISED MAY 2016
COUT ≥ 680 μF
COUT = 680-μF electrolytic capacitor
2. The capacitor's voltage rating must be at last 1.5 times greater than the output voltage. For a 10-V regulator,
a rating of at least 15 V or more is recommended. Higher voltage electrolytic capacitors generally have lower
ESR numbers, and for this reason it may be necessary to select a capacitor rate for a higher voltage than
would normally be needed.
8.2.2.2.4 Catch Diode Selection (D1)
1. The catch-diode current rating must be at least 1.2 times greater than the maximum load current. Also, if the
power supply design must withstand a continuous output short, the diode must have a current rating equal to
the maximum current limit of the LM2576. The most stressful condition for this diode is an overload or
shorted output. See Table 3. For this example, a 3.3-A current rating is adequate.
2. The reverse voltage rating of the diode should be at least 1.25 times the maximum input voltage. Use a 30-V
31DQ03 Schottky diode, or any of the suggested fast-recovery diodes in Table 3.
8.2.2.2.5 Input Capacitor (CIN)
An aluminum or tantalum electrolytic bypass capacitor located close to the regulator is needed for stable
operation. A 100-μF aluminum electrolytic capacitor located near the input and ground pins provides sufficient
bypassing.
Table 3. Diode Selection Guide
SCHOTTKY
VR
3A
FAST RECOVERY
4 A to 6 A
3A
4 A to 6 A
The following
diodes are all
rated to 100-V
31DF1
HER302
The following
diodes are all
rated to 100-V
50WF10
MUR410
HER602
1N5820
20 V
MBR320P
1N5823
SR302
1N5821
MBR330
30 V
50WQ03
1N5824
31DQ03
SR303
1N5822
MBR340
50WQ04
1N5825
MBR340
40 V
31DQ04
SR304
MBR350
50 V
31DQ05
50WQ05
SR305
MBR360
60 V
50WR06
50SQ060
DQ06
SR306
Table 4. Inductor Selection by Manufacturer's Part Number
(1)
(2)
(3)
INDUCTOR CODE
INDUCTOR VALUE
SCHOTT (1)
PULSE ENG. (2)
RENCO (3)
L47
47 μH
671 26980
PE-53112
RL2442
L68
68 μH
671 26990
PE-92114
RL2443
L100
100 μH
671 27000
PE-92108
RL2444
L150
150 μH
671 27010
PE-53113
RL1954
L220
220 μH
671 27020
PE-52626
RL1953
L330
330 μH
671 27030
PE-52627
RL1952
Schott Corporation, (612) 475-1173, 1000 Parkers Lake Road, Wayzata, MN 55391.
Pulse Engineering, (619) 674-8100, P.O. Box 12235, San Diego, CA 92112.
Renco Electronics Incorporated, (516) 586-5566, 60 Jeffryn Blvd. East, Deer Park, NY 11729.
Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
Submit Documentation Feedback
23
LM2576, LM2576HV
SNVS107D – JUNE 1999 – REVISED MAY 2016
www.ti.com
Table 4. Inductor Selection by Manufacturer's Part Number (continued)
INDUCTOR CODE
INDUCTOR VALUE
SCHOTT (1)
PULSE ENG. (2)
RENCO (3)
L470
470 μH
671 27040
PE-53114
RL1951
L680
680 μH
671 27050
PE-52629
RL1950
H150
150 μH
671 27060
PE-53115
RL2445
H220
220 μH
671 27070
PE-53116
RL2446
H330
330 μH
671 27080
PE-53117
RL2447
H470
470 μH
671 27090
PE-53118
RL1961
H680
680 μH
671 27100
PE-53119
RL1960
H1000
1000 μH
671 27110
PE-53120
RL1959
H1500
1500 μH
671 27120
PE-53121
RL1958
H2200
2200 μH
671 27130
PE-53122
RL2448
9 Power Supply Recommendations
As in any switching regulator, layout is very important. Rapidly switching currents associated with wiring
inductance generate voltage transients which can cause problems. For minimal inductance and ground loops, the
length of the leads indicated by heavy lines should be kept as short as possible. Single-point grounding (as
indicated) or ground plane construction should be used for best results. When using the adjustable version,
physically locate the programming resistors near the regulator, to keep the sensitive feedback wiring short.
24
Submit Documentation Feedback
Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
LM2576, LM2576HV
www.ti.com
SNVS107D – JUNE 1999 – REVISED MAY 2016
10 Layout
10.1 Layout Guidelines
Board layout is critical for the proper operation of switching power supplies. First, the ground plane area must be
sufficient for thermal dissipation purposes. Second, appropriate guidelines must be followed to reduce the effects
of switching noise. Switch mode converters are very fast switching devices. In such cases, the rapid increase of
input current combined with the parasitic trace inductance generates unwanted L di/dt noise spikes. The
magnitude of this noise tends to increase as the output current increases. This noise may turn into
electromagnetic interference (EMI) and can also cause problems in device performance. Therefore, take care in
layout to minimize the effect of this switching noise. The most important layout rule is to keep the AC current
loops as small as possible. Figure 33 shows the current flow in a buck converter. The top schematic shows a
dotted line which represents the current flow during the top-switch ON-state. The middle schematic shows the
current flow during the top-switch OFF-state. The bottom schematic shows the currents referred to as AC
currents. These AC currents are the most critical because they are changing in a very short time period. The
dotted lines of the bottom schematic are the traces to keep as short and wide as possible. This also yields a
small loop area reducing the loop inductance. To avoid functional problems due to layout, review the PCB layout
example. Best results are achieved if the placement of the LM2576 device, the bypass capacitor, the Schottky
diode, RFBB, RFBT, and the inductor are placed as shown in Figure 34.TI also recommends using 2-oz copper
boards or heavier to help thermal dissipation and to reduce the parasitic inductances of board traces. See
application note AN-1229 SIMPLE SWITCHER® PCB Layout Guidelines (SNVA054) for more information.
Figure 33. Current Flow in Buck Application
Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
Submit Documentation Feedback
25
LM2576, LM2576HV
SNVS107D – JUNE 1999 – REVISED MAY 2016
www.ti.com
10.2 Layout Example
Figure 34. LM2576xx Layout Example
10.3 Grounding
To maintain output voltage stability, the power ground connections must be low-impedance (see Figure 26 and
Figure 32). For the 5-lead TO-220 and DDPAK/TO-263 style package, both the tab and pin 3 are ground and
either connection may be used, as they are both part of the same copper lead frame.
10.4 Heat Sink and Thermal Considerations
In many cases, only a small heat sink is required to keep the LM2576 junction temperature within the allowed
operating range. For each application, to determine whether or not a heat sink is required, the following must be
identified:
1. Maximum ambient temperature (in the application).
2. Maximum regulator power dissipation (in application).
3. Maximum allowed junction temperature (125°C for the LM2576). For a safe, conservative design, a
temperature approximately 15°C cooler than the maximum temperatures must be selected.
4. LM2576 package thermal resistances θJA and θJC.
Total power dissipated by the LM2576 can be estimated in Equation 10:
PD = (VIN)(IQ) + (VO/VIN)(ILOAD)(VSAT)
where
•
•
•
26
IQ (quiescent current) and VSAT can be found in Typical Characteristics shown previously,
VIN is the applied minimum input voltage, VO is the regulated output voltage,
and ILOAD is the load current.
Submit Documentation Feedback
(10)
Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
LM2576, LM2576HV
www.ti.com
SNVS107D – JUNE 1999 – REVISED MAY 2016
Heat Sink and Thermal Considerations (continued)
The dynamic losses during turnon and turnoff are negligible if a Schottky type catch diode is used.
When no heat sink is used, the junction temperature rise can be determined by Equation 11:
ΔTJ = (PD) (θJA)
(11)
To arrive at the actual operating junction temperature, add the junction temperature rise to the maximum ambient
temperature.
TJ = ΔTJ + TA
(12)
If the actual operating junction temperature is greater than the selected safe operating junction temperature
determined in step 3, then a heat sink is required.
When using a heat sink, the junction temperature rise can be determined by Equation 13:
ΔTJ = (PD) (θJC + θinterface + θHeat sink)
(13)
The operating junction temperature is:
TJ = TA + ΔTJ
(14)
As in Equation 14, if the actual operating junction temperature is greater than the selected safe operating
junction temperature, then a larger heat sink is required (one that has a lower thermal resistance).
Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
Submit Documentation Feedback
27
LM2576, LM2576HV
SNVS107D – JUNE 1999 – REVISED MAY 2016
www.ti.com
11 Device and Documentation Support
11.1 Device Support
11.1.1 Device Nomenclature
11.1.1.1 Definition of Terms
BUCK REGULATOR A switching regulator topology in which a higher voltage is converted to a lower voltage.
Also known as a step-down switching regulator.
BUCK-BOOST REGULATOR A switching regulator topology in which a positive voltage is converted to a
negative voltage without a transformer.
DUTY CYCLE (D) Ratio of the output switch's on-time to the oscillator period.
(15)
CATCH DIODE OR CURRENT STEERING DIODE The diode which provides a return path for the load current
when the LM2576 switch is OFF.
EFFICIENCY (η) The proportion of input power actually delivered to the load.
(16)
CAPACITOR EQUIVALENT SERIES RESISTANCE (ESR) The purely resistive component of a real capacitor's
impedance (see Figure 35). It causes power loss resulting in capacitor heating, which directly
affects the capacitor's operating lifetime. When used as a switching regulator output filter, higher
ESR values result in higher output ripple voltages.
Figure 35. Simple Model of a Real Capacitor
Most standard aluminum electrolytic capacitors in the 100 μF–1000 μF range have 0.5Ω to
0.1Ω ESR. Higher-grade capacitors (low-ESR, high-frequency, or low-inductance) in the 100
μF to 1000 μF range generally have ESR of less than 0.15Ω.
EQUIVALENT SERIES INDUCTANCE (ESL) The pure inductance component of a capacitor (see Figure 35).
The amount of inductance is determined to a large extent on the capacitor's construction. In a buck
regulator, this unwanted inductance causes voltage spikes to appear on the output.
OUTPUT RIPPLE VOLTAGE The AC component of the switching regulator's output voltage. It is usually
dominated by the output capacitor's ESR multiplied by the inductor's ripple current (ΔIIND). The
peak-to-peak value of this sawtooth ripple current can be determined by reading Inductor Ripple
Current.
CAPACITOR RIPPLE CURRENT RMS value of the maximum allowable alternating current at which a capacitor
can be operated continuously at a specified temperature.
STANDBY QUIESCENT CURRENT (ISTBY) Supply current required by the LM2576 when in the standby mode
(ON /OFF pin is driven to TTL-high voltage, thus turning the output switch OFF).
INDUCTOR RIPPLE CURRENT (ΔIIND) The peak-to-peak value of the inductor current waveform, typically a
sawtooth waveform when the regulator is operating in the continuous mode (vs. discontinuous
mode).
CONTINUOUS/DISCONTINUOUS MODE OPERATION Relates to the inductor current. In the continuous mode,
the inductor current is always flowing and never drops to zero, vs. the discontinuous mode, where
the inductor current drops to zero for a period of time in the normal switching cycle.
INDUCTOR SATURATION The condition which exists when an inductor cannot hold any more magnetic flux.
28
Submit Documentation Feedback
Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
LM2576, LM2576HV
www.ti.com
SNVS107D – JUNE 1999 – REVISED MAY 2016
Device Support (continued)
When an inductor saturates, the inductor appears less inductive and the resistive component
dominates. Inductor current is then limited only by the DC resistance of the wire and the available
source current.
OPERATING VOLT MICROSECOND CONSTANT (E•Top) The product (in VoIt•μs) of the voltage applied to the
inductor and the time the voltage is applied. This E•Top constant is a measure of the energy
handling capability of an inductor and is dependent upon the type of core, the core area, the
number of turns, and the duty cycle.
11.2 Documentation Suuport
11.2.1 Related Documentation
For related documentation, see the following:
AN-1229 SIMPLE SWITCHER® PCB Layout Guidelines (SNVA054)
11.3 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 5. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
LM2576
Click here
Click here
Click here
Click here
Click here
LM2576HV
Click here
Click here
Click here
Click here
Click here
11.4 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.5 Trademarks
E2E is a trademark of Texas Instruments.
SIMPLE SWITCHER is a registered trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.6 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.7 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
Submit Documentation Feedback
29
LM2576, LM2576HV
SNVS107D – JUNE 1999 – REVISED MAY 2016
www.ti.com
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
30
Submit Documentation Feedback
Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM2576 LM2576HV
PACKAGE OPTION ADDENDUM
www.ti.com
2-Sep-2017
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM2576HVS-12
NRND
DDPAK/
TO-263
KTT
5
45
TBD
Call TI
Call TI
-40 to 125
LM2576
HVS-12 P+
LM2576HVS-12/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
45
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LM2576
HVS-12 P+
LM2576HVS-3.3/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
45
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LM2576
HVS-3.3 P+
LM2576HVS-5.0
NRND
DDPAK/
TO-263
KTT
5
45
TBD
Call TI
Call TI
-40 to 125
LM2576
HVS-5.0 P+
LM2576HVS-5.0/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
45
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LM2576
HVS-5.0 P+
LM2576HVS-ADJ
NRND
DDPAK/
TO-263
KTT
5
45
TBD
Call TI
Call TI
-40 to 125
LM2576
HVS-ADJ P+
LM2576HVS-ADJ/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
45
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LM2576
HVS-ADJ P+
LM2576HVSX-12
NRND
DDPAK/
TO-263
KTT
5
500
TBD
Call TI
Call TI
-40 to 125
LM2576
HVS-12 P+
LM2576HVSX-12/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
500
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LM2576
HVS-12 P+
LM2576HVSX-3.3/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
500
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LM2576
HVS-3.3 P+
LM2576HVSX-5.0
NRND
DDPAK/
TO-263
KTT
5
500
TBD
Call TI
Call TI
-40 to 125
LM2576
HVS-5.0 P+
LM2576HVSX-5.0/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
500
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LM2576
HVS-5.0 P+
LM2576HVSX-ADJ
NRND
DDPAK/
TO-263
KTT
5
500
TBD
Call TI
Call TI
-40 to 125
LM2576
HVS-ADJ P+
LM2576HVSX-ADJ/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
500
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LM2576
HVS-ADJ P+
LM2576HVT-12
NRND
TO-220
KC
5
45
TBD
Call TI
Call TI
-40 to 125
LM2576HVT
-12 P+
LM2576HVT-12/LF03
ACTIVE
TO-220
NDH
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
LM2576HVT-12/NOPB
ACTIVE
TO-220
KC
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
Addendum-Page 1
LM2576HVT
-12 P+
-40 to 125
LM2576HVT
-12 P+
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
2-Sep-2017
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM2576HVT-15/LB03
NRND
TO-220
NDH
5
45
TBD
Call TI
Call TI
LM2576HVT
-15 P+
LM2576HVT-15/LF03
ACTIVE
TO-220
NDH
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
LM2576HVT
-15 P+
LM2576HVT-15/NOPB
ACTIVE
TO-220
KC
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
-40 to 125
LM2576HVT
-15 P+
LM2576HVT-5.0
NRND
TO-220
KC
5
45
TBD
Call TI
Call TI
-40 to 125
LM2576HVT
-5.0 P+
LM2576HVT-5.0/LB03
NRND
TO-220
NDH
5
45
TBD
Call TI
Call TI
LM2576HVT
-5.0 P+
LM2576HVT-5.0/LF02
ACTIVE
TO-220
NEB
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
LM2576HVT
-5.0 P+
LM2576HVT-5.0/LF03
ACTIVE
TO-220
NDH
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
LM2576HVT
-5.0 P+
LM2576HVT-5.0/NOPB
ACTIVE
TO-220
KC
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
-40 to 125
LM2576HVT
-5.0 P+
LM2576HVT-ADJ
NRND
TO-220
KC
5
45
TBD
Call TI
Call TI
-40 to 125
LM2576HVT
-ADJ P+
LM2576HVT-ADJ/LB03
NRND
TO-220
NDH
5
45
TBD
Call TI
Call TI
LM2576HVT
-ADJ P+
LM2576HVT-ADJ/LF03
ACTIVE
TO-220
NDH
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
LM2576HVT
-ADJ P+
LM2576HVT-ADJ/NOPB
ACTIVE
TO-220
KC
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
-40 to 125
LM2576HVT
-ADJ P+
LM2576S-12
NRND
DDPAK/
TO-263
KTT
5
45
TBD
Call TI
Call TI
-40 to 125
LM2576S
-12 P+
LM2576S-12/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
45
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LM2576S
-12 P+
LM2576S-3.3/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
45
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LM2576S
-3.3 P+
LM2576S-5.0
NRND
DDPAK/
TO-263
KTT
5
45
TBD
Call TI
Call TI
-40 to 125
LM2576S
-5.0 P+
LM2576S-5.0/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
45
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LM2576S
-5.0 P+
LM2576S-ADJ/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
45
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LM2576S
-ADJ P+
Addendum-Page 2
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
2-Sep-2017
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM2576SX-3.3/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
500
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LM2576S
-3.3 P+
LM2576SX-5.0/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
500
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LM2576S
-5.0 P+
LM2576SX-ADJ/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
500
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LM2576S
-ADJ P+
LM2576T-12
NRND
TO-220
KC
5
45
TBD
Call TI
Call TI
-40 to 125
LM2576T
-12 P+
LM2576T-12/LB03
NRND
TO-220
NDH
5
45
TBD
Call TI
Call TI
LM2576T
-12 P+
LM2576T-12/LF03
ACTIVE
TO-220
NDH
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
LM2576T
-12 P+
LM2576T-12/NOPB
ACTIVE
TO-220
KC
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
LM2576T-15/LF03
ACTIVE
TO-220
NDH
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
LM2576T-15/NOPB
ACTIVE
TO-220
KC
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
LM2576T-3.3/LF03
ACTIVE
TO-220
NDH
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
LM2576T-3.3/NOPB
ACTIVE
TO-220
KC
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
-40 to 125
LM2576T
-3.3 P+
LM2576T-5.0
NRND
TO-220
KC
5
45
TBD
Call TI
Call TI
-40 to 125
LM2576T
-5.0 P+
LM2576T-5.0/LB03
NRND
TO-220
NDH
5
45
TBD
Call TI
Call TI
LM2576T
-5.0 P+
LM2576T-5.0/LF02
ACTIVE
TO-220
NEB
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
LM2576T
-5.0 P+
LM2576T-5.0/LF03
ACTIVE
TO-220
NDH
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
LM2576T
-5.0 P+
LM2576T-5.0/NOPB
ACTIVE
TO-220
KC
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
-40 to 125
LM2576T
-5.0 P+
LM2576T-ADJ
NRND
TO-220
KC
5
45
TBD
Call TI
Call TI
-40 to 125
LM2576T
-ADJ P+
LM2576T-ADJ/LB03
NRND
TO-220
NDH
5
45
TBD
Call TI
Call TI
Addendum-Page 3
-40 to 125
LM2576T
-12 P+
LM2576T
-15 P+
-40 to 125
LM2576T
-15 P+
LM2576T
-3.3 P+
LM2576T
-ADJ P+
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
2-Sep-2017
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM2576T-ADJ/LF02
ACTIVE
TO-220
NEB
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
LM2576T
-ADJ P+
LM2576T-ADJ/LF03
ACTIVE
TO-220
NDH
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
LM2576T
-ADJ P+
LM2576T-ADJ/NOPB
ACTIVE
TO-220
KC
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
-40 to 125
LM2576T
-ADJ P+
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 4
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
2-Sep-2017
Addendum-Page 5
PACKAGE MATERIALS INFORMATION
www.ti.com
18-Jan-2016
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
LM2576HVSX-12
DDPAK/
TO-263
KTT
5
500
330.0
24.4
LM2576HVSX-12/NOPB
DDPAK/
TO-263
KTT
5
500
330.0
LM2576HVSX-3.3/NOPB DDPAK/
TO-263
KTT
5
500
DDPAK/
TO-263
KTT
5
LM2576HVSX-5.0/NOPB DDPAK/
TO-263
KTT
DDPAK/
TO-263
LM2576HVSX-ADJ/NOPB DDPAK/
TO-263
LM2576HVSX-5.0
LM2576HVSX-ADJ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
10.75
14.85
5.0
16.0
24.0
Q2
24.4
10.75
14.85
5.0
16.0
24.0
Q2
330.0
24.4
10.75
14.85
5.0
16.0
24.0
Q2
500
330.0
24.4
10.75
14.85
5.0
16.0
24.0
Q2
5
500
330.0
24.4
10.75
14.85
5.0
16.0
24.0
Q2
KTT
5
500
330.0
24.4
10.75
14.85
5.0
16.0
24.0
Q2
KTT
5
500
330.0
24.4
10.75
14.85
5.0
16.0
24.0
Q2
LM2576SX-3.3/NOPB
DDPAK/
TO-263
KTT
5
500
330.0
24.4
10.75
14.85
5.0
16.0
24.0
Q2
LM2576SX-5.0/NOPB
DDPAK/
TO-263
KTT
5
500
330.0
24.4
10.75
14.85
5.0
16.0
24.0
Q2
LM2576SX-ADJ/NOPB
DDPAK/
TO-263
KTT
5
500
330.0
24.4
10.75
14.85
5.0
16.0
24.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
18-Jan-2016
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM2576HVSX-12
DDPAK/TO-263
KTT
5
500
367.0
367.0
45.0
LM2576HVSX-12/NOPB
DDPAK/TO-263
KTT
5
500
367.0
367.0
45.0
LM2576HVSX-3.3/NOPB
DDPAK/TO-263
KTT
5
500
367.0
367.0
45.0
LM2576HVSX-5.0
DDPAK/TO-263
KTT
5
500
367.0
367.0
45.0
LM2576HVSX-5.0/NOPB
DDPAK/TO-263
KTT
5
500
367.0
367.0
45.0
LM2576HVSX-ADJ
DDPAK/TO-263
KTT
5
500
367.0
367.0
45.0
LM2576HVSX-ADJ/NOPB
DDPAK/TO-263
KTT
5
500
367.0
367.0
45.0
LM2576SX-3.3/NOPB
DDPAK/TO-263
KTT
5
500
367.0
367.0
45.0
LM2576SX-5.0/NOPB
DDPAK/TO-263
KTT
5
500
367.0
367.0
45.0
LM2576SX-ADJ/NOPB
DDPAK/TO-263
KTT
5
500
367.0
367.0
45.0
Pack Materials-Page 2
MECHANICAL DATA
NEB0005B
www.ti.com
PACKAGE OUTLINE
KC0005A
TO-220 - 16.51 mm max height
SCALE 0.850
TO-220
4.83
4.06
10.67
9.65
3.05
2.54
B
1.40
1.14
A
6.86
5.69
3.71-3.96
8.89
6.86
(6.275)
12.88
10.08
OPTIONAL
CHAMFER
16.51
MAX
2X (R1)
OPTIONAL
9.25
7.67
C
(4.25)
PIN 1 ID
(OPTIONAL)
NOTE 3
14.73
12.29
1
5X
0.25
5
0.61
0.30
1.02
0.64
C A B
3.05
2.03
4X 1.7
6.8
1
5
4215009/A 01/2017
NOTES:
1. All controlling linear dimensions are in inches. Dimensions in brackets are in millimeters. Any dimension in brackets or parenthesis are for
reference only. Dimensioning and tolerancing per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. Shape may vary per different assembly sites.
www.ti.com
EXAMPLE BOARD LAYOUT
KC0005A
TO-220 - 16.51 mm max height
TO-220
4X (1.45)
PKG
0.07 MAX
ALL AROUND
0.07 MAX
ALL AROUND
METAL
TYP
(1.45)
PKG
(2)
4X (2)
1
(R0.05) TYP
5X ( 1.2)
SOLDER MASK
OPENING, TYP
(1.7) TYP
5
FULL R
TYP
(6.8)
LAND PATTERN
NON-SOLDER MASK DEFINED
SCALE:12X
4215009/A 01/2017
www.ti.com
MECHANICAL DATA
NDH0005D
www.ti.com
MECHANICAL DATA
KTT0005B
TS5B (Rev D)
BOTTOM SIDE OF PACKAGE
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s noncompliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2017, Texas Instruments Incorporated
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Texas Instruments:
LM2576T-15 LM2576T-15/LB03 LM2576T-15/LF03 LM2576T-15/NOPB LM2576T-3.3 LM2576T-3.3/LB03
LM2576T-3.3/LF03 LM2576T-3.3/NOPB LM2576T-5.0 LM2576T-5.0/LB03 LM2576T-5.0/LF02 LM2576T-5.0/LF03
LM2576T-5.0/NOPB LM2576T-ADJ LM2576T-ADJ/LB02 LM2576T-ADJ/LB03 LM2576T-ADJ/LF02 LM2576TADJ/LF03 LM2576T-ADJ/NOPB LM2576S-12 LM2576S-12/NOPB LM2576S-3.3 LM2576S-3.3/NOPB LM2576S-5.0
LM2576S-5.0/NOPB LM2576S-ADJ LM2576S-ADJ/NOPB LM2576SX-3.3 LM2576SX-3.3/NOPB LM2576SX-5.0
LM2576SX-5.0/NOPB LM2576SX-ADJ LM2576SX-ADJ/NOPB LM2576T-12 LM2576T-12/LB03 LM2576T-12/LF03
LM2576T-12/NOPB
Download PDF
Similar pages