ORION Benchtop Dishwasher 8 Place White

INSTALLATION
INSTRUCTIONS
USER GUIDE
VOGUE ORION Benchtop Dishwasher 8 Place White
340808
To prevent the risk of accidents or damage to the appliance, it is essential
to read these instructions before it is installed and used for the first time
Quick operation guide
For detailed operating method read the corresponding content on the instruction manual.
Switch on the appliance
Fill the detergent dispenser
Check the rinse aid level
Load the baskets
Select a program
Running the dishwasher
Press the Power switch button to switch on the appliance, Open the door.
Compartment A:
With each wash cycle.
Compartment B:
For programmes with pre-wash only.
(Follow the user instructions!)
C
A
B
Mechanical indicator C.
Electric indicator on control panel (if provided).
Scrape off any large amount of leftover food. Soften remnants of burnt food in pans,
then load the baskets. Refer to the dishwasher loading instructions.
Close the door Press the program button until the selected program lights up.
( See the section entitled Operation instruction )
T urn on the water tap and press the Start/Pause button. The machine will start working after about
10 seconds.
Changing the programme
1. A running cycle can only be modified if it has been running for a short time. Otherwise the detergent
may have already been released and the water already drained. If this is the case, the detergent
dispenser must be refilled.
2. Press the Start/Pause button ,than press the program button more than 3 seconds to cancel the
running programme.
3. Select a new programme.
4. Restart the dishwasher.
WARNING!
Add forgotten dishes in the
dishwasher.
1.Press the start/pause button to stop the machine.
2.Open the door.
3.Add the forgotten dishes.
4.Close the door, then press the start/pause button, the dishwasher will
start running again .
If the appliance is switched
off during a wash cycle.
If the appliance is switched off during a wash cycle, when switched
on again, please re-select the washing cycle and operate the dishwasher
according to the original Power-on state ).
Switch off the appliance
When the working cycle has finished, the buzzer of the dishwasher will sound 8 times, then stop.
Turn off the appliance using the Power button.
Since the appliance is standing by, it will power off automaticly after 30 minutes without any operation.
Turn off the water tap,
unload the baskets
Open the door carefully.
Hot steam may escape
when the door is opened!
Warning: wait a few minutes (about 15 minutes) before unloading the dishwasher to avoid handling
the dishes and utensils while they are still hot and more susceptible to break.
They will also dry better.Unload the appliance, starting from the lower basket.
Read this Manual
1) Safety Information..........................................1
2) Disposal.........................................................2
Dear Customer,
Please carefully read this manual before using the
dishwasher, it will help you to use and maintain the
dishwasher properly.
Keep it to refer to it at a later date.
Pass it on to any subsequent owner of the appliance.
This manual contains sections on safety Instructions,
Operating Instructions, Installation Instructions and
Troubleshooting Tips, etc.
Before Calling for Service
To review the section on troubleshooting Tips
will help you to solve some common problems
by yourself .
If you can not solve the problems by yourself ,
please ask for the help of professional technicians.
3) Operation Instruction.......................................3
Control Panel...................................................3
Dishwasher Features.................................... ...3
4) Prior using for the first time...............................4
A. Rinse Aid Dispenser.....................................4
B. Detergent ....................................................5
5) Loading the Dishwasher Basket........................6
Attention before or after loading the Dishwasher
Baskets..........................................................7
Loading the Basket...........................................7
Cutlery Basket................................................8
6) Starting a washing programme........................9
Wash Cycle Table...........................................9
Turning on the Appliance................................9
Change the Programme..................................10
At the end of the Wash Cycle...........................10
7) Maintenance and cleaning..............................11
Filtering System.............................................12
Caring for the Dishwasher...............................12
NOTE:
The manufacturer, following a policy of constant
development and updating of the product, may
make modifications without giving prior notice.
This user manual shall also be got from the
manufacturer or responsible vendor.
8) Installation instruction....................................13
instruction...................... .. ............13
Installation preparation..................................13
Positioning the Appliance...............................14
Water Connection..........................................14
Connection of Drain Hoses.............................15
Start of dishwasher.........................................16
9) Troubleshooting Tips................................
Tips......................................17
.. ....17
Before calling for service.................................17
Error codes...................................................18
Technical information.....................................19
1.IMPORTANT SAFETY INFORMATION
WARNING! When using your dishwasher,
follow the precautions listed below:
This appliance is intended to be used in household and similar
applications such as:
-staff kitchen areas in shops, offices and other working environments;
-farm houses;
-by clients in hotels, motels and other residential type environments;
-bed and breakfast type environments.
This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way and understand
the hazards involved. Children shall not play with the appliance. Cleaning
and user maintenance shall not be made by children without supervision.
For EN60335-1
This appliance is not intended for use by persons(including children )with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge ,unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
For IEC60335-1
This appliance is for indoor use only, for household use only. To protect
against the risk of electrical shock, do not immerse the unit, cord or plug in
water or other liquid.
Please unplug before cleaning and maintenance the appliance .Use a soft
cloth moisten with mild soap, and then use a dry cloth to wipe it again .
EARTHING INSTRUCTIONS
This appliance must be earthed. In the event of a malfunction or breakdown,
earthing will reduce the risk of an electric shock by providing a path of least
resistance of electric current. This appliance is equipped with a cord having
an equipment-earthing conductor and a earthing plug.
The plug must be plugged into an appropriate outlet that is installed and
earth ed in accordance with all local codes and ordinances.
Improper connection of the equipment-earthing conductor can result
in the risk of an electric shock. Check with a qualified electrician or service
representative if you are in doubt whether the appliance is properly earthed.
Do not modify the plug provided with the appliance; If it does not fit the outlet.
Have a proper outlet installed by a qualified electrician.
1-1
Do not abuse, sit on, or stand on the door or dish rack of the dishwasher.
Do not operate your dishwasher unless all enclosure panels are properly in place.
Open the door very carefully if the dishwasher is operating, there is a risk of water
squirting out.
Do not place any heavy objects on or stand on the door when it is open. The
appliance could tip forward.
When loading items to be washed:
1) Locate sharp items so that they are not likely to damage the door seal;
2) Warning: Knives and other utensils with sharp points must be loaded in the
basket with their points down or placed in a horizontal position.
Check that the detergent powder is empty after completion of the wash cycle.
Do not wash plastic items unless they are marked dishwasher safe or the
equivalent. For plastic items not so marked, check the manufacturer's
recommendations.
Use only det ergent and rinse additives designed for an aut omatic dishwasher.
Never use soap, laundry detergent, or hand washing detergent in your dishwasher.
Children should be supervised to ensure that they do not play with the appliance.
The door should not be left open, since this could increase the risk of tripping.
If the supply cord is damaged, it must be replaced by the manufacturer or
its service agent or a similarly qualified person in order to avoid a hazard.
During installation, the power supply must not be excessively or dangerously
bent or flattened.
Do not tamper with controls.
The appliance is to be connected to the water mains using new hose sets and
that old hose-sets should not be reused.
The maximum number of place settings to be washed is 8.
The maximum permissible inlet water pressure is 1MPa.
The minimum permissible inlet water pressure is 0.04MPa.
1-2
Disposal
Dispose of the dishwasher packaging material correctly.
All packaging materials can be recycled.
Plastic parts are marked with the standard international
abbreviations:
PE
for polyethylene, e.g. sheet wrapping material
PS
for polystyrene, e.g. padding material
POM
polyoxymethylene, e.g. plastic clips
PP
polypropylene, e.g. Salt filler
ABS
Acrylonitrile Butadiene Styrene, e.g. Control Panel .
WARNING!
Packaging material could be dangerous for children!
For disposing of package and the appliance please go to a
recycling centre. Therefore cut off the power supply cable
and make the door closing device unusable.
Cardboard packaging is manufactured from recycled paper
and should be disposed in the waste paper collection for
recycling.
By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the
environment and human health, which could otherwise be
caused by inappropriate waste handling of this product.
For more detailed information about recycling of this
product, please contact your local city office and your
household waste disposal service.
DISPOSAL: Do not dispose this product as unsorted
municipal waste. Collection of such waste separately for
special treatment is necessary.
2
3.Operation Instruction
IMPORTANT
To get the best performance from your dishwasher, read all operating instructions
before using it for the first time.
Control Panel
5
4
1
2
6
4
7
4
4
3
8
1
Power Button: To turn on/off the power supply.
2
Rinse Aid Warning Light : To be on when the
rinse aid dispenser needs to be refilled..
3
Program ending Light : To be on when the washing
program is finished.
7
Program Button : To select the wash cycles
4
Delay time:2/4/6/8 hours option .
(6h:the 2h and 4h lights on at the same time).
8
Start/Pause Button: Press this button to start
or pause the dishwasher.
Delay Button : To select the delay time.
Program indicator light: To be on when the
washing program have been chose.
Dishwasher Features
4
5
6
2
1
7
4
3
1
Detergent Dispenser
3
Rinse Aid Dispenser
5
Cup Shelf
7
Inlet pipe
connector
2
Filter assembly
4
Spray Arms
6
Basket
8
Drain pipe
connector
3
8
4.Prior using for the first time
Before using your dishwasher for the first time:
A. Rinse aid dispenser
B. Detergent
A. Rinse Aid Dispenser
Rinse Aid Dispenser
The rinse aid is released during the final rinse to prevent water from forming droplets on your dishes, which can
leave spots and streaks. It also improves drying by allowing water to roll off the dishes. Your dishwasher is
designed to use liquid rinse aids. The rinse aid dispenser is located inside the door next to the detergent dispenser.
To fill the dispenser, open the cap and pour the rinse aid into the dispenser until the level indicator turns completely
black. The volume of the rinse aid container is about 110ml.
Function of Rinse Aid
Rinse aid is automatically added during the last rinse, ensuring thorough rinsing, and spot and streak free drying.
Attention!
Only use branded rinse aid for dishwasher. Never fill the rinse aid dispenser with any other substances
(e.g. Dishwasher cleaning agent, liquid detergent). This would damage the appliance.
When to Refill the Rinse Aid Dispenser
If there is no rinse-aid warning light in the control panel, you can judge the amount of rinse-aid by the color of the
optical level
indicator "C" located next to the cap. When the rinse-aid container is full, the whole indicator will be dark .As the
rinse-aid
diminishes, the size of the dark dot decreases. You should never let the rinse aid get below 1 / 4 full.
As the rinse aid diminishes, the size of the black dot
on the rinse aid level indicator changes, as illustrated below.
Full
3 / 4 fu ll
1 / 2 fu ll
1 / 4 full - Should refill to eliminate spotting
Empty
C (Rinse-Aid indicator)
How to fill the Rinse Aid Dispenser
1
2
3
To open the dispenser, turn the cap to the "open" (left) arrow and lift it out.
Pour the rinse aid into the dispenser, being careful not to overfill.
Replace the cap by inserting it aligned with "open" arrow and turning it to the closed (right) arrow.
Be careful not to overfill the dispenser, because this could cause over sudsing. Wipe away any spills
with a damp cloth. Don't forget to replace the cap before you close dishwasher door.
Attention!
Clean up any rinse aid spill during filling with an absorbent cloth to avoid excess foaming
during the next wash.
4
NOTE:
Clean up any rinse aid spilled while during filling with an absorbent cloth to avoid excessive foaming
during the next wash. Don't forget to replace the cap before you close dishwasher door.
Adjusting Rinse Aid Dispenser
The rinse aid dispenser has six or four settings. Always start with the dispenser
set on "4". If spots and poor drying are a problem, increase the amount of rinse
aid dispensed by removing the dispenser lid and rotating the dial to "5". If the
dishes still are not drying properly or are show spots, adjust the dial to the next
higher lever until your dishes are spot-free. The recommended setting is "4".
(Factory value is "4".)
Adjust lever
(Rinse)
MAX
NOTE:
Increase the dose if there are drops of water or lime spots on the dishes after washing.
Reduce it if there are sticky whitish stains on your dishes or a bluish film on glassware or
knife blades.
B. Detergent
Detergents have chemical ingredients that are necessary to remove dirt, crush dirt and transport it out of the dishwasher.
Most of the commercial quality detergents are suitable for this purpose.
Detergents
There are 3 sorts of detergents
1.With phosphate and with chlorine
2.With phosphate and without chlorine
3.Without phosphate and without chlorine
Normally new pulverised detergent is without phosphate. Thus the water softener function of
phosphate is not given. If detergents without phosphate are used in the case of hard water
often white spots appear on dishes and glasses. In this case please add more detergent to reach
better results. Detergents without chlorine do only bleach a little. Strong and coloured spots will not
be removed completely. In this case please choose a program with a higher temperature.
Concentrated Detergent
Based on their chemical composition, detergents can be split in two basic types:
Conventional, alkaline detergents with caustic components
Low alkaline concentrated detergents with natural enzymes
The use of normal washing programs in combination with concentrated detergents
reduces pollution and is good for your dishes; these wash programs are specifically matched
to the dirt-dissolving properties of the enzymes of the concentrated detergent. For this reason
normal wash programs in which concentra ted dete rgents are use d can achie ve t he sa me
results that can otherwise only be achieved using intensive programs.
Detergent Tablets
Detergent tablets of different brands dissolve at different speeds. For this reason some
detergent tablets cannot dissolve and develop their full cleaning power during short
programs. Therefore please use long programs when using detergent tablets, to
ensure the complete removal of detergent residuals.
Detergent Dispenser
The dispenser must be refilled before the start of each wash cycle following the instructions
provided in the wash cycle table . Your dishwasher uses less detergent and rinse aid than
Conventional dishwasher. Generally, only one tablespoon of detergent is needed for
a normal wash load. More heavily soiled items need more detergent. Always add the
detergent just before starting the dishwasher, otherwise it could get damp and will not
dissolve properly.
Proper Use of Detergent
Use only detergent specifically made for the use in dishwashers. Keep your detergent fresh and dry.
Don't put powdered detergent into the dispenser until you're ready to wash dishes.
5
Adding detergent to dispenser
Push latch to open
A
Fill in Detergent
Fill the detergent dispenser with detergent.
The marking indicates the dosing levels , as
illustrated on the right:
Please observe the manufacturers dosing and storage
Recommendations as stated on the detergent packaging.
B
A
For main wash detergent.
B
For pre-wash detergent.
Close the lid and press until it locks in place.
If the dishes are heavily soiled, place an additional
detergent dose in the pre-wash detergent chamber. This detergent will take effect during the pre-wash phase.
NOTE:
If the lid is closed: push the latch to open.
Always add the detergent just before starting each wash cycle.
Only use branded detergent and rinse aid for dishwasher.
You see information about the amount of detergent for the single programme on the last page.
Please be aware that soiling levels and water hardness can effect wash results.
Please observe the manufacturer's recommendations on the detergent packaging.
WARNING!
Dishwasher detergent is corrosive!
Take care to keep it out of reach of children.
5.Loading the Dishwasher Baskets
Recommendation
Consider buying utensils which are identified as dishwasher-proof.
Use a mild detergent that is described as 'kind of dishes'. If necessary, seek further
information from detergent manufacturers.
For particular items, select a programme with as low a temperature.
To prevent damage, do not take glass and cutlery out of the dishwasher immediately
after the programme has ended.
For washing in the dishwasher the following cutlery/dishes
Are not suitable
Are of limited suitability
Cutlery with wooden, horn china or
mother-of-pearl handles
Plastic items that are not heat resistant
Older cutlery with glued parts that is not
temperature resistant
Bonded cutlery items or dishes
Pewter or copper items
crystal glass
Steel items subject to rusting
Wooden platters
Items made from synthetic fibres
Some types of glasses can become
dull after a large number of washes
Silver and aluminium parts have a
tendency to discolour during washing
Glazed patterns may fade if machine
washed frequently
6
Attention before or after loading the Dishwasher Baskets
(For best performance of the dishwasher, follow these loading guidelines.
Features and appearance of baskets and cutlery baskets may vary from your model.)
Scrape off any large amounts of leftover food. Soften remnants of burnt food in pans
It is not necessary to rinse the dishes under running water.
Place objects in the dishwasher in following way:
1.Items such as cups, glasses, pots/pans, etc. are face down.
2.Curved items, or those with recesses, should be loaded at a slant so that water can run off.
3.All utensils are stacked securely and can not tip over.
4.All utensils are placed in the way that the spray arms can rotated freely during washing.
NOTE: Very small items should not be washed in the dishwasher as they could easily fall out of the basket.
Load hollow items such as cups, glasses, pans etc. With the opening downwards so that
water cannot collect in the container or a deep base.
Dishes and items of cutlery must not lie inside one another, or cover each other.
To avoid damage to glasses, they must not touch.
Load large items which are most difficult to clean into the basket.
Long bladed knives stored in an upright position are a potential hazard!
Long and/or sharp items of cutlery such as carving knives must be positioned
horizontally in the basket.
Please do not overload your dishwasher. This is important for good results and for
reasonable energy consume.
Loading the baskets according to AS/NZS 2007:1:
1.Upper basket:
2.Lower basket:
Down Shelf
1
1
6
5
4
IN
2
3
1
2
Up Shelf
NOTE: MAXIMUM PLATE SIZE 17CM
Cups
1
3
4
5
Glasses
Dessert dishes
Dinner plates
6
2
Saucers
4
7
Soup plates
Note: Please place the light flat wares on the up shelf. The
total weight is less than 2kg.
Up Shelf
IN
3
4
5
4
Down Shelf
IN
2
1
1 Soup spoons
4 Teaspoons
2 Forks
5 Dessert spoons
3 Knives
Information for comparability tests in
accordance with (*AS/NZS 2007.1)
Voltage:220~2 40V/50Hz
Capacity: 8 place settings
Programme: ECO
Detergent(Pre/ main): 5 g/20g
Rinse aid setting: 6
Door is open at the end of the drying cycle for the
drying performance test (Door position: Open 50 mm)
WARNING!
Do not let any item extend through bottom.
Always load sharp utensils with the sharp point down!
For personal safety and a top quality clean, place the silverware in the basket:
They do not nest together.
Place silverware with handles-down.
But place knives and other potentially dangerous utensils handles-up.
8
6.Starting a washing programme
Wash Cycle Table
Cycle Selection
Information
Program
Intensive
Heavy
Energy
(Kwh)
Water
(l)
155
1.25
12
5/20g
150
1.05
12
5/20g
160
0.54
9.16
5/20g
95
0.7
12
25g
90
1.15
10
For heaviest soiled crockery
soiled pots pans dishes
etc with dried on soiling.
For heavily soiled loads,
such as pots, plates,
glasses and lightly
soiled pans.
Pre-wash(45
Wash (60 )
Rinse
Rinse (68 )
Drying
Glass
For lightly soiled loads,
such as glasses, crystal and
fine china.
90 min
For lightly soiled crockery
and glass.
Pre-wash
Wash (50
Rinse (50
Drying
)
)
Pre-wash
Wash (45
Rinse
Rinse (60
Drying
)
)
)
Wash(55
Wash(65
Rinse(68
Drying
)
)
)
Wash (45 )
A shorter wash for lightly soiled Rinse
loads and quick wash.
Rinse (55 )
Rapid
Running
time(min)
Pre-wash(50 )
Wash (65 )
Rinse
5/20g
Rinse
(Or 1 piece)
Rinse (70 )
Drying
This is standard program,
it is suitable to clean normally
soiled tableware and it is the
most efficient programme in
terms of its combined energy
and water consumption for
that type of tableware.
( *AS/NZS 2007.1)
Detergent
pre/main
Description
of Cycle
15g
35
0.52
7
NOTE:
*AS/NZS 2007.1 : This programme is the test cycle. The information for comparability test
in accordance with AS/NZS 2007.1 , as follows:
Capacity: 8 settings
Rinse aid setting: 6
The power consumption of off-mode is 0.45W
left-on mode is 0.49W
Turning On the Appliance
Starting a wash cycle
Draw out the basket(see the section entitled Loading the Dishwasher ).
Pour in the detergent (see the section entitled Detergent
and Rinse Aid ).
Insert the plug into the socket. The power supply is 220-240
VAC 50 HZ, the specification of the socket is 10 A 250 VAC.
Make sure that the water supply is turned on to full pressure.
Press the program button , the wash program will be changed as follows direction
ECO->Glass->90 min->Rapid->Intensive->Heavy;
If a program is selected, the response light will light. Then press the
Start/Pause button, the dishwasher begins to start.
NOTE:
When you press the Start/Pause button to pause during washing,
the program light will stop blinking and the dishwasher will mooing
every minute unless you press the Start/Pause button to start.
9
Rinse
Aid
Change the Program
Premise: You can modify the washing program, When the dishwasher just
runs for a short time. Otherwise, the detergent may have already been
released, and the appliance may have already drained the wash water. If this
is the case, the detergent dispenser must be refilled (see the section entitled
" Loading the Detergent " ).
Press Start/Pause Button to pause the machine when the door is closed ,Press
Program Button more than three seconds the machine will be in stand by state ,
then you can change the program to the desired cycle setting (see the section
entitled " Starting a wash cycle" ).
NOTE: If you open the door during washing, the machine will pause. When you
close the door , the machine will keep on working after 10 seconds.
The program lights show the state of the dishwasher:
a) One of the program lights on----------stand by or pause
b) One of the program lights blinking----- run
NOTE:
If you open the door when washing, the machine will pause. When you close the door , the machine
will keep on working after 10 seconds.
Forget to Add a Dish
A forgotten dish can be added any time before the detergent cup opens.
4 Add forgotten dishes.
1 Press the Start/Pause button
2 Open the door a little to stop the washing.
5
Close the door
the spray arms stop working,you can open the door
3 After
completely.
6
Press the Start/Pause button, the dishwasher will run
after 10 seconds.
At the end of the Wash Cycle
When the working cycle has finished, the buzzer of dishwasher will sound 8 seconds, then stop. Turn off
the appliance using the ON/OFF button, shut off the water supply and open the door of the dishwasher.
Wait a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they
are still hot and more susceptible to breakage. They will also dry better.
Switch Off the Dishwasher
1.Switch off the dishwasher by pressing the ON/OFF button.
2.Turn off the water tap!
Open the door carefully.
Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool down around 15 minutes
before removing from the appliance.
Open the dishwasher's door, leave it ajar and wait a few minutes before removing the dishes. In this way they
will be cooler and the drying will be improved.
Unloading the dishwasher
It is normal that the dishwasher is wet inside.
WARNING!
It is dangerous to open the door when washing,
because the hot water may scald you.
10
7.Maintenance and Cleaning
Filtering System
The filter prevent larger remnants of food or other objects from getting inside the pump.
The filter system consists of a coarse filter, a flat (Main filter)
and a micro filter (fine filter).
C
Main filter
A
Food and soil particles trapped by this filter are pulverized by a
special jet on the spray arm and washed down to drain.
B
Fine filter
B
This filter holds soil and food residue in the sump area and
prevents it from being deposited on the dishes during wash cycle.
A
Coarse filter
C
Larger items, such as pieces of bone or glass, that could block
the drain are trapped in the coarse filter. To remove the items
caught by the filter, gently squeeze the tap on the top of this
filter and lift out.
Filter assembly
The filter efficiently removes food particles from the wash water, allowing it to be re-cyclated during the cycle.
For best performance and results, the filter assembly must be regularly. For this reason, it is a good idea to
remove the larger food particles trapping in the filter after each wash cycle by rinsing the filter and cup under
running water. To remove the filter assembly, pull on the cup handle in the upward direction.
WARNING!
Never run the dishwasher without the filters in place.
The dishwasher must never be used without the filters.
Improper replacement of the filter may reduce the performance level of the appliance
and damage dishes and utensils.
Open
Step1 contrarotate the filter assembly(A,B and C),
then lift it all up.
C
B
A
Step2:
lift B and C up from A;
C
B
The End.
A
NOTE: If do it from step1 to step 3, the filter system will be removed; while if do it from Step 3 to Step 1,
the filter system will be installed.
11
Remarks:
- Inspect the filters for blocking every time the dishwasher has been used.
- By unscrewing the coarse filter.you can remove the filter system.Remove any food remnants and
clean the filters under running water.
NOTE: The entire filter assembly should be cleaned once a week.
Cleaning The Filter
To clean the coarse filter and the fine filter, use a cleaning brush. Reassemble the filter parts as shown in the figures
in the last page and reinsert the entire assembly in the dishwasher, positioning in its seat and pressing downward.
WARNING!
When cleaning the filters, don't knock on them. Otherwise, the filters could be
contorted and the performance of dishwasher could be debased.
Caring for the Dishwasher
The control panel can be cleaned by using a lightly dampened cloth and dry thoroughly.
The exterior use a good appliance polish wax.
Never use sharp objects, scouring pads or harsh cleaners on any part of the dishwasher.
Cleaning The Door
To clean the edge around the door, you should use only a soft warm,
damp cloth. To avoid penetration of water into the door lock and
electrical components, do not use a spray cleaner of any kind.
n
WARNING!
Never use a spray cleaner to clean the door panel as it may damage the door lock
and electrical components.
n
Abrasive agent or some paper towel should not be used because of the risk of
scratching or leaving spots on the stainless steel surface.
Protect Against Freezing
please take frost protection measures on dishwasher in winter. Each time after washing cycles,
please operate as follows
1.Cut off electrical power to the dishwasher.
2.Turn off the water supply and disconnect the water inlet pipe from the water valve.
3.Drain water from the inlet pipe and water valve. (Use a pan to catch the water)
4.Reconnect the water inlet pipe to the water valve.
5.Remove the filter at the bottom of the tub and use a sponge to use up water in sump.
NOTE:
If your dishwasher cannot work because of the ice, please contact professional service persons.
12
Cleaning the Spray Arms
It is necessary to clean the spray arms regularly for hard
water chemicals will clog the spray arm jets and bearings.
Open
To remove the upper spray arm, hold the nut, rotate the arm
clockwise to remove it.
To remove the lower spray arm, pull out the spray arm upward.
Wash the arms in soapy and warm water and use a soft brush to
clean the jets. Replace them after rinsing them thoroughly.
How to Keep Your Dishwasher in Shape
After Every Wash
When it is not in need for a long time
After every wash, turn off the water supply to the
appliance and leave the door slightly open so that
moisture and odors are not trapped inside.
It is recommend that you run a wash cycle with the
dishwasher empty and then remove the plug from the
socket, turn off the water supply and leave the door of
the appliance slightly open. This will help the door
seals to ast longer and prevent odours from forming
within the appliance.
Remove the Plug
Before cleaning or performing maintenance, always
remove the plug from the socket.
Moving the Appliance
No Solvents or Abrasive Cleaning
To clean the exterior and rubber parts of the dishwasher,
do not use solvents or abrasive cleaning products.
Only use a cloth with warm soapy water.
To remove spots or stains from the surface of the
interior, use a cloth dampened with water with a little
vinegar, or a cleaning product made specifically for
dishwashers.
If the appliance must be moved, try to keep it in the
vertical position. If absolutely necessary, it can be
positioned on its back.
Seals
One of the factors that cause odors to form in the
dishwasher is food that remains trapped in the seals.
Periodic cleaning with a damp sponge will prevent this
from occurring.
8.Installation instruction
Warning
Attention:
Electrical Shock Hazard
Disconnect electrical power
before installing dishwasher.
The installation of the pipes
and electrical equipments
should be done by professionals.
Failure to do so can result in
death or electrical shock.
Installation preparation
The installation position of dishwasher should be near the existing inlet and drain
hoses and power cord.
One side of the cabinet sink should be chosen to facilitate the connection of drain
hoses of the dishwasher.
13
Positioning the Appliance
Position the appliance in the desired location. The back should rest against the wall behind it,
and the sides, along the adjacent cabinets or wall. The dishwasher is equipped with water supply
and drain hoses that can be positioned to the right or the left to facilitate proper installation.
About Power Connection
WARNING!
For personal safety:
Do not use an extension cord or an adapter plug
with this appliance.
n
Do not cut or remove the earthing connection from the power cord
under any circumstances.
n
Electrical Requirements
Please look at the rating label to know the rating voltage and connect the dishwasher to the appropriate power supply.
Use the required fuse 10 amp, time delay fuse or circuit breaker recommended and provide separate circuit serving
only this appliance.
Electrical Connection
Insure proper ground
exists before use
Ensure the voltage and frequency of the power being corresponds to
those on the rating plate. Only insert the plug into an electrical socket which is earthed
properly. If the electrical socket to which the appliance must be connected is not
appropriate for the plug , replace the socket, rather than using a adaptors or the like as
they could cause overheating and burns.
Water Connection
Cold Water Connection
Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure
that it is fastened tightly in place. If the water pipes are new or have not been used for
an extended period of time, let the water run to make sure that the water is clear and
free of impurities. If this precaution is not taken, there is a risk that the water inlet can
get blocked and damage the appliance.
WARNING!
please close the hydrant after using.
14
Connection of drain hoses
Insert the drain hose into a drain pipe with a minimum diameter of 4cm, or let it
run into the sink, making sure to avoid bending or crimping it. Use the special
plastic support that comes with the appliance. The free end of the hose must be
at a height lower than75cm and must not be immersed in water to avoid the back
flow of it.
Attention:
The special plastic hose support must be solidly fastened to the wall to
prevent the drain hose from moving and allowing water to spill outside
the drain.
PLEASE HANG UP THE DRAIN HOSE EITHER WAY OF A, B
Counter
NOTE
The top of the hose
must be less than
750mm.
Drain pipe
A
MAX 750mm
Front
B
40mm
15
How to Drain Excess Water From Hoses
If the sink is 1000 higher from the floor, the excess water in hoses cannot be drained directly
into the sink. It will be necessary to drain excess water from hoses into a bowl or suitable
container that is held outside and lower than the sink.
Water Outlet
Connect the water drain hose. The drain hose must be correctly fitted to avoid water leaks.
Ensure that the water drain hose is not kinked or squashed.
Extension Hose
If you need a drain hose extension, observe to use a similar drain hose.
It must be no longer than 4 metres; otherwise the cleaning effect of the dishwasher could be reduced.
Start of dishwasher
The following things should be checked before starting the dishwasher.
1 The dishwasher is level and fixed properly
2
3
4
5
6
7
The inlet valve is open
Inlet hose connections are fully tightened and not leaking
The wires are tightly connected
The power is switched on
The inlet and drain hoses are knotted
All packing materials and printings should be taken out from the dishwasher
Attention:
After installation, please make sure to keep this manual.
The content of this manual is very helpful to the users.
16
9.Troubleshooting Tips
Before Calling for Service
Review the charts on the following pages may save you from calling for service.
Problem
Possible Causes
Dishwasher doesn't Fuse blown, or the
circuit breaker tripped.
start
Technical
problems
Water not pumped
from dishwasher
Suds in the tub
Stained tub interior
White film on
General inside surface
problems
There are rust
stains on cutlery
Noise
What To Do
Replace fuse or reset circuit breaker. Remove any other
appliances sharing the same circuit with the dishwasher
Power supply is not
turned on.
Make sure the dishwasher is turned on and the door is
closed securely.
Make sure the power cord is properly plugged into the
wall socket.
Door of dishwasher
not properly closed.
Closed dishwasher making sure that door latches.
Kink in drain hose
Check drain hose.
Filter clogged.
Check the coarse filter.
(see section titled " Cleaning The Filter ")
Kitchen sink clogged.
Check kitchen sink to make sure it is draining well.
If problem is kitchen sink not draining ,you may need
a plumber rather than a serviceman for dishwasher.
Improper detergent
Use only the special dishwasher detergent to avoid
suds. If this occurs, open the dishwasher and let suds
evaporate. Add 1 gallon of cold water to the tub. Close
and latch the dishwasher, then Start any wash cycle
to drain out the water . Repeat if necessary.
Spilled rinse-aid
Always wipe up rinse-aid spills immediately.
Detergent with
colourant was used.
Make sure that the detergent is the one without
colourant.
Hard water minerals
To clean the interior, use a damp sponge with
dishwasher detergent and wear rubber gloves.
Never use any other cleaner than dishwasher
detergent for the risk of foaming or suds.
The affected items are
not corrosion resistant.
A programme was not
run after dishwasher
salt was added.
Traces of salt have
got into the wash cycle.
Always run the Quick wash programme .
without any crockery in the dishwasher and
without selecting the Turbo function (if present),
after adding dishwasher salt.
The lid of softer
is loose.
Check the lip .Ensure the fix is fine.
Knocking noise
in the wash cabinet
The spray arm is
knocking against
an item in a basket.
Interrupt the programme, and rearrange the items
which are obstructing the spray arm.
Rattling noise
in the wash cabinet
Item of crockery
are insecure
in the wash cabinet.
Interrupt the programme,
and rearrange the items of crockery.
Knocking noise
in the water pipes
This may be caused
by on-site installation
or the cross-section of
the piping.
This has no influence on dishwasher function.
if in doubt, contact a suitably qualified plumber.
17
Problem
Possible Causes
What To Do
The dishes
are not clean
The dishes were not
loaded correctly.
See notes in " Loading the Dishwasher Baskets ".
The programme was
not powerful enough.
Select a more intensive programme.
See" Wash Cycle Table ".
Not enough detergent
was dispensed.
Use more detergent, or change your detergent.
Item are blocking
the path of spray arms.
Rearrange the items so that the spray can rotate freely.
The filter combination
in the base of wash
cabinet is not clean or
is not correctly fitted.
This may cause
the spray arm jets
to get blocked.
Clean and/or fit the filter combination correctly.
Clean the spray arm jets. See "Cleaning the Spray
Arms".
Cloudiness
on glassware
Combination of soft
water and too much
detergent.
Use less detergent if you have soft water and select
a shortest cycle to wash the glassware and to get
them clean.
Black or gray
marks on dishes
Aluminum utensils
have rubbed against
dishes.
Use a mild abrasive cleaner to eliminate those marks.
Detergent left in
dispenser cups
The dishes
are not drying
Dishes block
detergent cups.
Re-loading the dishes properly.
Improper loading
Load the dishwasher as suggested in the directions.
Too little rinse-aid
Increase the amount of rinse-aid/Refill the rinse-aid
dispenser.
Dishes are removed
too soon.
Do not empty your dishwasher immediately after
washing. Open the door slightly so that the steam can
escape. Begin unloading the dishwasher only once t
he dishes are barely warm to the touch. Empty the low
basket first. This prevents water form dropping off
dishes in the upper basket.
Wrong programme
selection
In short programmes the washing temperature is lower.
This also lowers cleaning performance. Choose a
programme with a long washing time.
Using cutlery with
a low-quality coating
Water drainage is more difficult with these items.
Cutlery or dishes of this type are not suitable for
washing in the dishwasher.
Unsatis
-factory
washing
result
Unsatis
-factory
drying
result
Error Codes
When some malfunctions come on, the appliance will display error codes to warn you:
Meanings
Codes
Possible Causes
Faucets is not opened, or water intake
is restricted, or water pressure is too low.
The Rapid light flicker fleetly
Longer inlet time.
The Rapid and 90min light flicker fleetly
Not reaching required temperature. Malfunction of heating elenent.
The Glass light flicker fleetly
Overflow.
WARNING!
Some element of dishwasher leaks .
n
n If overflow occurs, turn off the main water supply before calling a service.
If there is water in the base pan because of an overfill or small leak,
the water should be removed before restarting the dishwasher.
18
Technical Information
19
Download PDF
Similar pages