Technical Data Sheet
MS SEAM SEALANT
Revision: 13/08/2007
Page 1 of 2
Technical Characteristics:
Base
Consistency
Curing System
MS Polymer®
Thixotropic paste
Moisture Cure
Skin Formation (*) (20°C/65% R.V.)
Curing time (*) (20°C/65% R.V.)
Hardness Shore A (DIN 53505)
approx. 12 min.
2 à 3 mm/24h
35 ± 3
Specific Gravity (DIN 53479)
Temperature Resistance (fully cured)
Elasticity Modulus 100 % (DIN 53504)
1,62 g/mL
-40°C to +90°C
0,90 N/mm²
Maximum tension (DIN 53504)
Elongation at break (DIN 53504)
1,00 N/mm²
> 400 %
(*) these values may vary depending on environmental factors such as temperature, moisture, and type of substrates
Product:
Soudal MS Seam sealant is a high quality,
completely neutral, single component fully elastic
seam sealant. It is based on MS-Polymer®.
Shelflife:
12 months in unopened packaging in a cool and dry
storage place at temperatures between +5°C and
+25°C.
Characteristics:
Professional OEM-like finish
High adhesion strength on most substrates
High performance mechanical properties
Permanent elastic after curing
Can be painted wet-on-wet with waterborn
paints
Free of silicone, solvent and isocyanate
Colourfast
UV resistant
Resistance to chemical agents:
Good resistance to water, mineral oils, grease,
diluted inorganic acids and alkalis
Poor resistance to aromatic and aliphatic solvents,
concentrated acids, concentrated alkalis and
chlorinated hydrocarbons.
Applications:
For the sealing of welding seams and sheet
metal connections in the trunk, the motor area,
in wheel bases, around suspensions and on all
welding seems
Protection of welding points
Corrosion protection on spoilers, car trunks and
wheel bases etc.
Substrates:
Type: various substrates such as steel, metal,
galvanized metal and other common materials in
the automotive industrie.
Not suitable for PE and PP
State of Surface: clean, free of dust and grease
Priming: Surface Activator may be used to clean
and pre-treat non-porous surfaces.
We recommend preliminary compatibility tests prior
to application.
Packaging:
Colour: light yellow, grey available upon special
request
Packaging: cartridge 290mL
Remark: The directives contained in this documentation are the result of our experiments and of our experience and have been submitted in good faith.
Because of the diversity of the materials and substrates and the great number of possible applications which are out of our control, we cannot accept any
responsability for the results obtained. In every case it is recommended to carry out preliminary experiments.
Soudal NV
Tel.: +32 (0)14-42.42.31
Everdongenlaan 18-20
Fax: +32 (0)14-42.65.14
2300 Turnhout, Belgium
www.soudal.com
Technical Data Sheet
MS SEAM SEALANT
Revision: 13/08/2007
Page 2 of 2
Applying the sealant:
Method: MS seam sealant can be applied by
means of a special telescopic pneumatical
caulking gun. Both in beads and in various types of
coating.
Application temperature: +5°C until +35°C
Cleaning: MS Seam Sealant can, before the
sealant is cured, be removed from tools and
materials with Soudal Fix All Cleaner. Cured
sealant has to be removed mechanically.
Tooling: with soapy solution before skin formation
Repair with: MS Seam Sealant
Health- and Safety Recommendation:
Apply the usual industrial hygiene.
Check the packaging for more information
Remarks:
Soudal MS Seam Sealer may be overpainted
with most types of lacquer used in industrial
applications, however due to the large number
of paints and varnishes available we strongly
suggest a compability test before application.
The drying time of alkyd resin based paints
may increase.
Soudal MS Seam Sealer can be applied to a
wide variety of substrates. Due to the fact that
specific substrates such as plastics,
polycarbonate, etc, may differ from
manufacturer to manufacturer, a preliminary
adhesion test with these materials is
imperative.
Remark: The directives contained in this documentation are the result of our experiments and of our experience and have been submitted in good faith.
Because of the diversity of the materials and substrates and the great number of possible applications which are out of our control, we cannot accept any
responsability for the results obtained. In every case it is recommended to carry out preliminary experiments.
Soudal NV
Tel.: +32 (0)14-42.42.31
Everdongenlaan 18-20
Fax: +32 (0)14-42.65.14
2300 Turnhout, Belgium
www.soudal.com