Optical networking solutions
XFP Transceivers
FTX-M1XG-S85L-30MD
XFP 10GBase-SR, 850nm, multi-mode, 300m
Description
FTX-M1XG-S85L-30MD series XFP+ transceiver can be used to setup a reliable, high speed serial data link over multi-mode fiber. Maximum
link span can reach 300m. Casing made fully from metal alloys ensures very good EMI immunity. Module is fully compliant with XFP+ MSA
specification and it is available in two hardware versions:
Model
Operating case temperature
FTX-M1XG-S85L-30MD
0~70°C
FTX-M1XG-S85L-30MDI
-40~85°C
Host device can access module internal EEPROM memory and DDMI via I2C interface.
Built-in digital diagnostic interface (DOM, DDMI) allows a network administrator to monitor module parameters such as: transmitted and
received optical power, temperature, supply voltage and laser current. Those information and data are very helpful e.g. in prediction and
prevention of connection failures. A module is available in various dedicated versions, which can be compatible with devices from vendors
such as Cisco, HP, Juniper, Extreme Networks, Alcatel-Lucent, 3Com, Linksys and more.
Applications

10G Ethernet

Fiber Channel (10G FC)

SONET/SDH (OC-192/STM64)

Gigabit Ethernet (1.25Gbps)
Fibrain Co., Ltd.
Address: ul. Wspólna 4A, 35-205 Rzeszów, Poland
Tel: +48 17 86-60-811, +48 17 86-60-812
Fax: +48 17 86-60-810
Email: info@fibrain.com http://www.fibrain.com
Optical networking solutions
XFP Transceivers
Key features

LC Duplex receptacle

Transmission distance up to 300m*

VCSEL diode 850nm transmitter, PIN receiver

Throughput up to 11.3Gb/s

Fully compliant with XFP+ MSA INF-8077i and INF-8472 rev. 11.3

Hot-Pluggable

RoHS compliant

Class 1 laser safety

Low power dissipation (<1W)

Metal case for low EMI

Operating case temperature* : 0~70°C / -40~85°C
Specification
Supported transmission technology
10G Ethernet, Fibre Channel
Speed supported for Ethernet technology
10.25Gbps, 1.25Gbps
Speed supported for Fibre Channel technology
10.51875Gbps
Transmission medium
Multi-mode fiber 50/125µm
Transmission distance**
300m
Receptacle type
LC Duplex
Wavelength
850nm
* - standard / industrial version
** - transmission distance depends on optical link attenuation
Fibrain Co., Ltd.
Address: ul. Wspólna 4A, 35-205 Rzeszów, Poland
Tel: +48 17 86-60-811, +48 17 86-60-812
Fax: +48 17 86-60-810
Email: info@fibrain.com http://www.fibrain.com
Output power
-7~-1dBm
Receiver sensitivity
-11.1dBm
Power supply voltage
3.3V
Total power consumption
< 1W
Operating environment – temperature*
0~70°C / -40~+85°C
Operating environment - humidity
5~95% non-condensing
Dimensions
Compliant with XFP Multi-Source Agreement
Optical networking solutions
XFP Transceivers
Detailed technical specification
Pin Description
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Name
GND
VEE5
Mod_DeSel
Interrupt
TX_DIS
VCC5
GND
VCC3
VCC3
SCL
SDA
Mod_Abs
Mod_NR
RX_LOS
GND
GND
RDRD+
GND
VCC2
21
P_Down/RST
22
23
24
25
26
27
28
29
30
VCC2
GND
RefCLK+
RefCLKGND
GND
TDTD+
GND
Function/Description
Module Ground
Optional -5.2V Power Supply - Not Required
Module De-select; When held low allows module to respond to 2-wire serial interface
Interrupt; Indicates presence of an important condition
Transmitter Disable; Turns off transmitter laser output
+5V Power Supply - Not Required
Module Ground
+3.3V Power Supply
+3.3V Power Supply
2-Wire Serial Interface Clock
2-Wire Serial Interface Data Line
Indicates Module is not present. Grounded in the Module
Module Not Ready; Indicating Module Operational Fault
Receiver Loss Of Signal Indicator
Module Ground
Module Ground
Receiver Inverted Data Output
Receiver Non-Inverted Data Output
Module Ground
+1.8V Power Supply - Not Required
Power down; When high, requires the module to limit power consumption to 1.5W or
below. 2-Wire serial interface must be functional in the low power mode.
Reset; The falling edge initiates a complete reset of the module including the 2-wire
serial interface, equivalent to a power cycle.
+1.8V Power Supply - Not Required
Module Ground
Reference Clock Non-Inverted Input, AC coupled on the host board - Not Required
Reference Clock Inverted Input, AC coupled on the host board - Not Required
Module Ground
Module Ground
Transmitter Inverted Data Input
Transmitter Non-Inverted Data Input
Module Ground
Notes:
1. Module ground pins GND are isolated from the module case.
2. Shall be pulled up with 4.7KΩ to 10KΩ to a voltage between 3.15V and 3.45V on the host board.
3. Reference Clock is not required. If present, it will be ignored.
Fibrain Co., Ltd.
Address: ul. Wspólna 4A, 35-205 Rzeszów, Poland
Tel: +48 17 86-60-811, +48 17 86-60-812
Fax: +48 17 86-60-810
Email: info@fibrain.com http://www.fibrain.com
Logic
LVTTL-I
LVTTL-0
LVTTL-I
LVTTL-I/0
LVTTL-I/0
LVTTL-0
LVTTL-0
LVTTL-0
CML-0
CML-0
LVTTL-I
PECL-I
PECL-I
CML-1
CML-1
Notes
1
2
1
2
2
2
2
2
1
1
1
1
3
3
1
1
1
Optical networking solutions
XFP Transceivers
Electrical parameters
Parameter
Transmitter Differential Input Volt
Receiver Differential Output Volt
Input Voltage – Low
Tx_Disable,
P_Down/RST
Input Voltage - High
RX_LOS, Mod_NR, Output Voltage – Low
Interrupt
Output Voltage - High
Throughput
Total current requirement
Symbol
+/-TX_DAT
+/-RX_DAT
VIL
VIH
VOL
VOH
B
Min.
120
400
0
2.0
0
2.0
Typ.
Symbol
λc
Δλ
Po
EX
Min.
840
Typ.
850
Max.
1000
800
0.8
Vcc
0.8
Vcc
11.3
430
Unit
mV p-p
mV p-p
V
V
V
V
Gb/s
mA
Notes
1
2
Max.
860
0.45
-1
Unit
nm
nm
dBm
dB
dB
ps
Notes
Unit
dBm
dBm
nm
dBm
dBm
dBm
dB
dB
Notes
6
3
3
Transmitter parameters
Parameter
Central wavelength
Spectral width
Launch optical power
Extinction ratio
Dispersion penalty
Optical rise/fall time
Eye diagram
Trise/Tfall
-7
3
3.9
30
Compliant with IEEE802.3-2005 10G BASE-SR
4
5
Receiver parameters
Parameter
Sensitivity
Stressed Sensitivity (OMA)
Central wavelength
Receiver overload
RX_LOS Asserted
RX_LOS De-Asserted
RX_LOS Hysteresis
Optical return loss
Symbol
Pmin
Min.
λc
PMAX
SA
SD
ORL
840
-1
-30
Typ.
Max.
-11.1
-7.5
860
-12.1
3.0
12
6
Notes:
1.
Internally AC coupled and terminated to 100Ω differential load.
2.
Internally AC coupled, but requires a 100Ω differential termination or internal to Serializer/Deserializer.
3.
It is open collector/drain output which should be pulled up externally to Vcc with a 4.7KΩ-10KΩ resistor on the host board. LOS: logic 0
indicates normal operation; logic 1 indicates no signal detected.
4.
Optical power is launched into MMF
5.
20-80%
6.
Measured with PRBS 2 -1 at test pattern @10.3125Gbps.
31
Fibrain Co., Ltd.
Address: ul. Wspólna 4A, 35-205 Rzeszów, Poland
Tel: +48 17 86-60-811, +48 17 86-60-812
Fax: +48 17 86-60-810
Email: info@fibrain.com http://www.fibrain.com
Optical networking solutions
XFP Transceivers
Mechanical specification
Recommended environment conditions
Parameter
Operating Temperature Range (industrial)
Operating Temperature Range (standard)
Supply Voltage
Relative Humidity
Symbol
T
T
VCC
RH
Min
-40
0
3.135
5
Typ
25
3.3
-
Max
85
70
3.465
95
Unit
0C
0C
V
%
Ordering information
FTX-M1XG-S85L-30MD– 850nm, 300m, multi-mode, LC duplex, DDMI, commercial temperature (0~70°C)
FTX-M1XG-S85L-30MDI– 850nm, 300m, multi-mode, LC duplex, DDMI, extended temperature (-40~85°C)
For further information regarding host device PCB layout recommendation, power supply requirements, EEPROM memory map, DDMI specification please check:
SFF-8472 - Description of EEPROM and Digital Diagnostic Monitoring Interface and INF-8077i - Technical specification for XFP transceiver
Fibrain Sp. z o.o. reserves the right to make changes to the products or information contained herein without notice. No liability is assumed as a result of their use or application.
Pictures used for reference only, actual product look may differ. For most actual information please contact technical support via aktywa@fibrain.pl
Fibrain Co., Ltd.
Address: ul. Wspólna 4A, 35-205 Rzeszów, Poland
Tel: +48 17 86-60-811, +48 17 86-60-812
Fax: +48 17 86-60-810
Email: info@fibrain.com http://www.fibrain.com
Download PDF
Similar pages