HP ProLiant DL180 Generation 6

QuickSpecs
HP ProLiant DL180 Generation 6
Overview
Front View:
1. Access panel
2. Front LED Indicators
3. Power on/off
4. Optional DVD-RW or DVD-ROM drive
5. Front USB Ports (2)
6. Non-Hot Plug Non Redundant fans (4 fans)
7. Air Baffle
8. PCI Cage
9. System Board
Rear View:
1.
Redundant Power Supply Bay (Optional)
2.
Power Supply Cable Socket
3.
Low Profile Card Slot
4.
PCI Expansion Card Slot
5.
PCI Expansion Card Slot
6.
UID LED Button
7.
(Optional) LO100i 10/100 Mbps LAN port for IPMI
management (RJ-45)
8.
LAN Port
9.
LAN Port
10. 2 Rear USB 2.0 Ports
11. VGA Port
12. Serial Port
What's New
Support for SAS and SATA Hot Plug SFF Midline (MDL) Drives
At A Glance
The HP ProLiant DL180 G6 is a low cost high capacity storage optimized 2-way server that delivers on a history of design
excellence and 2U density for a variety of rack deployments and applications.
Processors:
Supports up to two Quad-Core Intel® Xeon® processors: 5500 sequence with 8MB Level 3 cache
Intel® 5520 Chipset
Memory:
Up to 96GB, using PC3-8500R DDR3Registered (RDIMM) memory, operating at 1066MHz when fully populated
at 2 DIMMs per Channel in 12 slots.
Up to 24GB, using PC3-10600E DDR3 Unbuffered (UDIMM) memory, operating at 1066MHz when fully
populated at 2 DIMMs per Channel in 12 slots
Internal Drive Support:
Support for up to twenty-five (25) SFF with a Smart Array controller.
Support for up to fourteen (14) LFF with a Smart Array controller:
Hot Plug Serial ATA (SATA) Models: Up to 14.0TB (14 x 1TB Hot Plug 3.5" hard drives)
Hot Plug Serial Attached SCSI (SAS) Models: SAS Model: Up to 14.0TB (14 x 1TB Hot Plug 3.5" hard
drives)
NOTE: Four (4), eight (8) and twelve (12) hard drives models are supported standard via BTO. Eight (8)
and twelve (12) hard drive model support requires the addition of a Smart Array or HBA controller. Hot
Plug and SAS functionality require the addition of a Smart Array or HBA controller.
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
Page 1
QuickSpecs
HP ProLiant DL180 Generation 6
Overview
Network Controller:
HP NC362i Integrated Dual Port Gigabit Server Adapter
Storage Controllers:
4 HDD BTO Models: HP Embedded SATA RAID Controller RAID 0,1,10
NOTE: Transfer rate: up to 3 Gb/s SATA
NOTE: To enable RAID on Embedded SATA, use the HP Smart Array B110i SATA Raid controller, To enable
use of the B110i, enter the ROM based setup utility(RBSU). The option for enabling RAID can be found in the
Advanced section of the RBSU
8 HDD BTO Models: HP Smart Array P410 /256MB Controller (RAID 0/1/1+0/5/5+0)
NOTE: A minimum of 256 MB cache, battery kit, and Smart Array Advanced Pack License Key upgrade is
required to enable RAID 6, 6+0
12 HDD BTO Models: HP Smart Array P212 /256MB Controller(RAID 0/1/1+0/5/5+0)
NOTE: A minimum of 256 MB cache, battery kit, and Smart Array Advanced Pack License Key upgrade is
required to enable RAID 6, 6+0
Expansion Slots:
One available Low Profile x16 PCI-Express slot using a Low profile Riser
Two Full Height/ Full Length Riser options:
Option1: 2 x8 full-length/full-height PCI-Express slots (Standard)
Option2: 2 PCI-X, full-length/full-height riser Slots(Optional)
Option 3: 1 x16 full-length / full-height slot (Optional)
Power Sources:
Dual Common Slot Bay for Right Sized, Hot plug and Redundant Power
HP 750W CS HE Gold Power Supply
HP 460W CS HE Gold Power Supply
Infrastructure Management:
HP Insight Control suite for Linux (ICE-LX), a product option, delivers essential infrastructure management that
can help save time and money by making it easy to deploy, monitor, control and optimize your IT infrastructure
through a single, simple management console. The ICE-LX suite supports Linux-based servers and
management consoles
HP ProLiant Onboard Administrator Powered Lights-Out 100i with optional LO100i Advanced Licenses for
Virtual KVM and Virtual Media.
The HP ProLiant Easy Set-up CDs and ISO image downloads offer Assisted and Manual single server
installation, setup, and deployment capability. Capabilities provided are:
AutoRun
Assisted Installation Microsoft Windows 2003 Server and Microsoft Windows 2008 Server
OS and SW available for Manual Installation are listed on each servers' QuickSpecs
Ports:
Five USB ports (two front, two rear , one optional internal)
NOTE: In order to utilize the internal USB port the USB cable (P/N: 536769-B21) must be connected to the
internal USB header
Optical Drive:
Support for one (optional): DVD-ROM, DVD/CD RW
Form Factor:
2U rack models
Operating Systems and Virtualization Software:
Supports Windows, RHEL, SLES, Solaris, VMware, and Citrix Essentials for XenServer (Retail)
Deployment/Serviceability:
HP ProLiant DL180 G6 models have fixed rails which provide support for racks with round mounting holes and
tool-free support for racks with square mounting holes (including Compaq/HP 7000, 9000, 10000 and HP
series), with an adjustment range of 26" - 36"
Tool-less access to all system components for easy in rack serviceability
Customer Self Repair (CSR): HP products are designed with many CSR parts to minimize repair time and allow
for greater flexibility in performing defective parts replacement
Warranty:
This product is covered by a global limited warranty and supported by HP Services and a worldwide network of
HP Authorized Channel Partners. Hardware diagnostic support and parts replacement is available for three
years from date of purchase. Support for software and initial setup is available for 90 days from date of
purchase. Enhancements to warranty services are available through HP Care Pack services or customized
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
Page 2
QuickSpecs
HP ProLiant DL180 Generation 6
Overview
service agreements. SATA hard drives have a one-year warranty. SAS Enterprise drives have a 3 year warranty.
NOTE: Server Warranty includes 3-Years Next Business Day Parts replacement, 0-Years Labor, 0-Years Onsite
support. Additional information regarding worldwide limited warranty and technical support is available at:
http://h18004.www1.hp.com/products/servers/platforms/warranty/index.html
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
Page 3
QuickSpecs
HP ProLiant DL180 Generation 6
Standard Features
NOTE: For the Standard Features shipped in the Factory Integrated Models, please see the "Configuration Information Factory Integrated Models" section.
Processor
Quad-Core Processors
One of the following
Intel® Xeon® Processor E5540 (2.53 GHz, 8MB L3 Cache, 80W, DDR3-1066, HT, Turbo 1/1/2/2)
depending on Model
NOTE: Available through Configure To Order only. See Factory Integration Models section for
more details.
Intel® Xeon® Processor E5520 (2.26 GHz, 8MB L3 Cache, 80W, DDR3-1066, HT, Turbo 1/1/2/2)
NOTE: Available through Configure To Order only. See Factory Integration Models section for
more details.
Intel® Xeon® Processor L5520 (2.26 GHz, 8MB L3 Cache, 60W, DDR3-1066, HT, Turbo 1/1/2/2)
NOTE: Available through Configure To Order only. See Factory Integration Models section for
more details.
Intel® Xeon® Processor E5504 (2.00 GHz, 4MB L3 Cache, 80W, DDR3-800)
NOTE: Available through Configure To Order only. See Factory Integration Models section for
more details.
NOTE: HT indicates that the processor model supports Intel® Hyper-Threading Technology.
NOTE: Turbo indicates the maximum potential frequency increment when using Intel® Turbo
Boost Technology, with 4, 3, 2, and 1 cores active.
NOTE: DDR3 speed is the maximum memory speed of the processor. Actual memory speed may
depend on the quantity and type of DIMMs installed.
NOTE: For the Intel 5500 Series, the letter preceding the model number indicates the
performance/wattage of the processor. "X" denotes High Performance/Wattage; "E" denotes
Enterprise Performance/Wattage (Mainstream); and "L" denotes Lower Wattage.
Upgradeability
Upgradeable to two processors
Chipset
Intel® 5520 Chipset
Cache Memory
4 MB Level 3 cache (E5504)
8 MB Level 3 cache (standard)
Memory Protection
Advanced memory protection
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
Page 4
QuickSpecs
HP ProLiant DL180 Generation 6
Standard Features
Memory
Type
Standard
DDR3 Registered (RDIMM) or Unbuffered (UDIMM)
4 GB
(2 x 2 GB)
6 GB
(3 x 2 GB)
12 GB
(6 x 2 GB)
Maximum (RDIMM)
96 GB
(12 x 8 GB)
Maximum (UDIMM)
24 GB
(12 x2 GB)
NOTE: Depending on the memory configuration and processor model, the memory speed may run
at 1333MHz, 1066MHz, or 800MHz. Please see the Online Memory Configuration Tool at:
www.hp.com/go/ddr3memory-configurator.
DDR3 memory options part number decoder
Network Controller
HP NC362i Integrated Dual Port Gigabit Server Adapter
Expansion Slots
Slot Number Bus Speed
3
1
x16 PCIExpress
x8 PCIExpress
x8 PCIExpress
PCI-X***
2
PCI-X***
1
2
Bus
Number*
3
Device
Number**
1
Hot Plug
(Y/N)
N
PCI Voltage
Notes
3.3 volts
Low Profile
5
0
N
3.3 volts
6
0
N
3.3 volts
Dynamic
1
N
3.3 volts
Dynamic
2
N
3.3 volts
Full Length
Full Height
Full Length
Full Height
Full Length
Full Height
Full Length
Full Height
NOTE: All slots can accept universal keyed PCI cards.
* Default bus assignment. Inserting cards with PCI bridges may alter the actual bus assignment
number.
** Slots are enumerated differently based on OS. MS OS's enumerate from lowest to highest
Device ID by bus (starting with the lowest bus).
*** PCI-X bus speed will be 133MHz when only one PCI-X card is installed. It will be 100MHz
when both slots have PCI-X cards installed.
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
Page 5
QuickSpecs
HP ProLiant DL180 Generation 6
Standard Features
Storage Controller
4HDD Models
HP Embedded SATA RAID Controller (integrated into the south-bridge)
supporting SW RAID 0,1,10
NOTE: Transfer rate up to 3.0 Gb/s SATA.
HP Smart Array B110i SATA RAID
NOTE: To enable RAID on Embedded SATA, use the HP Smart Array
B110i SATA Raid controller, To enable use of the B110i, enter the ROM
based setup utility(RBSU). The option for enabling RAID can be found in
the Advanced section of the RBSU.
8HDD Models
HP Smart Array P410/256MB Controller (RAID 0/1/1+0/5/5+0)
12HDD Models
HP Smart Array P212/256MB Controller (RAID 0/1/1+0/5/5+0)
NOTE: A diskette drive or virtual FDD using LO100 Advanced Pack is needed to install storage
controller drivers during a Windows operating system installation from a CD.
NOTE: A minimum of 256 MB cache, battery kit, and Smart Array Advanced Pack License Key
upgrade (P/N: 516471-B21) is required to enable RAID 6, 6+0
Storage
Diskette Drives
Optical Drives
Drive Bays
Via USB only
Optional HP Slim SATA DVD-ROM Optical Drive
Optional HP Slim SATA DVD RW Optical Drive
NOTE: Support in 4, 8, and 12 drive models . Optical drives can only be
installed in 12 drive model with rear option kit (515826-B21).
Up to 14 Hot Plug SAS/SATA 3.5" drives
NOTE: 4 Drive Models are Non-Hot Pluggable. Smart Array Controller
must be added for Hot Plug drive capability. 4 Drive Models can be
upgraded with the addition of a Smart Array Controller and a SAS/SATA
Multi-lane cable (496013-B21).
NOTE: The addition of a Smart Array Controller requires the addition of
a SAS/SATA Multi-lane cable (496013-B21).
Maximum Internal
Storage
Hot Plug SATA
Hot Plug SAS
14.0TB
14.0TB
14 x 1TB
14 x 1TB
Interfaces
Parallel
Network RJ-45
(Ethernet)
Serial
Pointing Device (Mouse)
Graphics
Keyboard
USB
None
2 10/100/1000 NIC ports (plus 1 dedicated for the HP ProLiant Lights
Out 100i Remote Management)
1
0 (via USB only)
1
0 (via USB only)
5 total ports: (2) front, (2) rear, (1) optional internal
NOTE: In order to connect a USB device internally, the internal USB
Cable G6 Kit must be used (536769-B21)
NOTE: Please see the following URL for additional information
regarding USB support:
http://h18004.www1.hp.com/products/servers/platforms/usbsupport.html.
Graphics
32MB shared supporting 1600 x 1200 x 16M resolution.
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
Page 6
QuickSpecs
HP ProLiant DL180 Generation 6
Standard Features
Form Factor
Rack (2U), (3.5 in/8.89 cm)
Embedded Systems
Management
HP ProLiant Onboard
Administrator and
LO100i Advanced
HP ProLiant Onboard Administrator (powered by LO100i Lights-Out 100
Baseboard Management Controller) with Optional LO100i Advanced
Licenses for Virtual KVM and Virtual Media.
Features:
Embedded IPMI standard reporting
System event log access
Remote Serial console (serial redirection)
Browser, Telnet access
SMASH-CLP compliant
IPMI 2.0 compliant
Secure Socket Layer Encryption
Secure Shell Encryption
Virtual media (Floppy, CD, USB 2.0) with Advanced License
Virtual KVM with Advanced License
Core Infrastructure
Management
HP Insight Control (ICE) HP Insight Control suite for Linux (ICE-LX), as a product option, delivers
suites
essential infrastructure management that can help save time and money
by making it easy to deploy, monitor, remote control, and optimize your
IT infrastructure through a single, simple management console. The
ICE-LX suite installs and license software modules that are integrated
into HP System Insight Manager.
The HP Insight Control suite for Linux (ICE-LX) serves environments
requiring a Linux-based management consoles. See:
www.hp.com/go/ice-linux
HP Insight Control suites include one year of 24 x 7 HP Software
Technical Support and Update Service ensuring rapid access to HP
support staff and proactive delivery of software updates. For more
information about this service, please visit:
http://www.hp.com/services/insight.
Industry Standard
Compliance
ACPI V2.0 Compliant
PCI 2.2 Compliant
PXE Support
WOL Support
Microsoft® Logo certifications
IPMI 2.0 Compliant
Security
Power-on password
Setup password
Diskette boot control
Secure Sockets Layer (SSL)
Secure Shell (SSH)
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
Page 7
QuickSpecs
HP ProLiant DL180 Generation 6
Standard Features
Security - Trusted
Platform Module
The TPM (Trusted Platform Module) is a microcontroller chip that can securely store artifacts used
to authenticate the server platform. These artifacts can include passwords, certificates and
encryption keys. Windows® BitLocker™ Drive Encryption (BitLocker) is a data protection feature
available in Windows Server® 2008. BitLocker leverages the enhanced security capabilities of a
Trusted Platform Module (TPM) version 1.2. The TPM works with BitLocker to help protect user
data and to ensure that a server running Windows Server 2008 has not been tampered with while
the system was offline.
NOTE: For more information about TPM, including a white paper, go to www.hp.com/go/TPM
NOTE: ProLiant OS pre-installed units will come with the partition required for TPM deployment.
NOTE: The TPM key is unique to every TPM deployed server and must be retained. Misplacing or
losing the key could result in data loss.
Server Power Cords
One 6' Highline (IEC-IEC) power cord ships standard
NOTE: HP ProLiant DL servers no longer ship standard with NEMA power cords (163719-002)
that allow connection to 110V US wall outlets in a home or office. ProLiant DL servers are
primarily connected to PDU's in data center racks so they now ship standard with only a PDU
power cord (416151-B21). If a user wishes to power a ProLiant DL server using a 110V receptacle
(NEMA-15), the NEMA power cord (227099-001) must be ordered separately.
If customers require a local power cord, they can check the power cord matrix for the appropriate
cord. Please see the following power cord matrix: http://www.hp.com/go/powercordmatrix
NOTE: Rack models ship standard with an IEC cable.
Localized cables included with geographic specific models in other world regions.
UPS and PDU Power
Cord Matrix
Please see the UPS and PDU cable matrix's on the HP Power Protection and Management page.
Under Power Cords, click on the "HP Power Cord Matrix" link. That link will list cable descriptions,
requirements, and specifications for UPS and PDU units. Please see the following link:
www.hp.com/products/powercords.
Power Supply
HP has a new design for ProLiant power. The new Common Slot Power Supply bay. This design
provides the customer with commonality in power supplies across multiple platforms to save on
the cost of spares and allows HP to offer multiple power solutions to fit the customers' needs.
Many HP ProLiant Servers come with Common Slot, High Efficiency and Right-Size Power
Supplies. Common Slot (CS) designates commonality of the power supply across multiple
ProLiant servers. HP's new Common Slot power supplies are designed for highest efficiency to
provide power efficiency without degrading performance of the ProLiant. Power Supplies will have
efficiency ratings up to 92%. There are three Right Size power options available, depending on
the configuration of your server. To make sure you select the correct power supply to meet your
configuration, we suggest that you use the HP Power Advisor to decide the "Right-Size" for your
configuration. All HP Common Slot power sources are UL, CE Mark Compliant, Hot Plug and
Redundant.
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
Page 8
QuickSpecs
HP ProLiant DL180 Generation 6
Standard Features
Common Slot ProLiant It is highly recommended that you use the HP Power Advisor in defining the "Right-Size" power
supply for your needs. HP offers Power Supply Options:
460Watts, Common Slot,92% Efficiency
750Watts, Common Slot, 92% Efficiency
1200Watts, Common Slot, 90% Efficiency
NOTE: 1200W power supply not supported on the DL180G6
HP's ProLiant Common Slot Power supplies (460W & 750W) meet multiple Energy Efficiency
Initiatives. Climate Savers Computing Initiative GOLD, ECOS Consulting 80PLUS GOLD and
plans on offering models that meet the Energy Star for Server requirements when they are
published.
HP's ProLiant Common Slot Power supplies (1200W) meet multiple Energy Efficiency Initiatives.
Climate Savers Computing Initiative Bronze, ECOS Consulting 80PLUS Bronze Power Supply
requirements.
Redundant Power: Optional (1+ 1 or n+n redundant) power supplies can be purchased through
power supply option kits (see Redundant Options for part numbers).
System Fans
4 system fans ship standard; Non-hot plug, Non-redundant
NOTE: Redundant fan kit (P/N 516009-B21) available for purchase.
Operating Systems and Microsoft Windows Server
Virtualization Software Microsoft Windows Server Hyper-V
Support for ProLiant
Red Hat Enterprise Linux (RHEL)
Servers
SUSE Linux Enterprise Server (SLES)
Oracle Enterprise Linux (OEL)
Solaris 10 for x86/x64 based Systems
VMware ESX Server
Citrix Essentials for XenServer (Retail)
NOTE: For more information on HP's Certified and Supported ProLiant Servers for OS and
Virtualization Software and latest listing of software drivers available for your server, please visit
our Support Matrix at: http://www.hp.com/go/supportos and our driver download page
http://www.hp.com/support/DL180G6
Rack Airflow
Requirements
Rack 10000 G2 series Cabinets
The increasing power of new high-performance processor technology requires increased cooling
efficiency for rack-mounted servers. The 10000 G2 Series Racks provide enhanced airflow for
maximum cooling, allowing these racks to be fully loaded with servers using the latest processors.
CAUTION: If a third-party rack is used, observe the following additional requirements to ensure
adequate airflow and to prevent damage to the equipment:
Front and rear doors: If your 42U server rack includes closing front and rear doors, you must allow
830 square inches (5,350 sq cm) of hole evenly distributed from top to bottom to permit adequate
airflow (equivalent to the required 64 percent open area for ventilation).
Side: The clearance between the installed rack component and the side panels of the rack must
be a minimum of 2.75 inches (7 cm).
CAUTION: Always use blanking panels to fill all remaining empty front panel U-spaces in the rack.
This arrangement ensures proper airflow. Using a rack without blanking panels results in improper
cooling that can lead to thermal damage.
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
Page 9
QuickSpecs
HP ProLiant DL180 Generation 6
Standard Features
Rack Kit
HP ProLiant DL180 rack models have fixed rails which provide support for racks with round
mounting holes and tool-free support for racks with square mounting holes (including Compaq/HP
7000, 9000, 10000 and HP series), with an adjustment range of 26" - 36".
Telco Rack Support
Support for all 2 and 4 post Telco racks and threaded hole racks requires an additional option kit
from Rack Solutions. The Rack Solutions brackets can be purchased at:
http://www.racksolutions.com/hp.
Factory Express
Portfolio for Servers
and Storage
HP Factory Express offers configuration, customization, integration and deployment services for
HP servers and storage products. Customers can choose how their factory solutions are built,
tested, integrated, shipped and deployed.
Factory Express offers service packages for simple configuration, racking, installation, complex
configuration and design services as well as individual factory services, such as image loading,
asset tagging, and custom packaging. HP products supported through Factory Express include a
wide array of servers and storage: HP Integrity, HP ProLiant, HP ProLiant Server Blades, HP
BladeSystem, HP 9000 servers as well as the MSAxxxx, VA7xxx, EVA, XP, rackable tape libraries
and configurable network switches.
For more information on Factory Express services for your specific server model please contact
your sales representative or go to: http://www.hp.com/go/factory-express.
HP Enterprise
Configurator
The HP eConfigure Enterprise Configurator now provides factory default racking for our HP
hardware portfolio. This approach is aligned with our strategic direction to meet the needs and
expectations of our valued customers. If you require "custom" rack configuration, please contact
HP's Customer Business Center or an Authorized Partner for assistance.
Service and Support
HP services provide total care and support expertise with committed response designed to meet
your IT and business needs.
HP Care Pack services include coverage for the HP branded hardware options qualified for the
server, purchased at the same time or afterward, internal to the enclosure, as well as 22" and
smaller external monitors and tower UPS options up to 3kVA; these items will be covered at the
same service level and for the same coverage period as the server. Coverage of UPS Battery is
not included, standard warranty terms & conditions apply. For servers or storage systems installed
within a rack, service also covers all HP qualified rack options installed within the same rack.
To fully capitalize on your HP ProLiant servers' capabilities requires a service partner who
thoroughly understands your server technology and systems environment. HP Services, an
industry leader in provision of multi vender support solutions provides a range of support services
designed to meet the varying needs of business. Whether an SMB or large global corporation HP
has a ProLiant server support offer to help you speedily deploy and maximize system uptime.
Recommended Service - Simplify ProLiant solution implementation, maintenance and
management.
Support Service - 3 Year, 9x5 Next Business Day coverage, excluding HP holidays only
Deployment Service - Hardware Installation only
Enhanced Service - Optimize service level to increase IT performance and availability
Support Service - 3 Year 13x5 Same Business Day, 4-Hour response coverage
Deployment Service - Installation and Start-up only
Installation & Start-Up of a ProLiant server and Microsoft or Linux O/S per the Customer
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
Page 10
QuickSpecs
HP ProLiant DL180 Generation 6
Standard Features
Description and/or Data Sheet. To be delivered on a scheduled basis 8am-5pm, M-F, excl. HP
holidays.
For a complete listing of service offerings and information visit:
http://www.hp.com/services/proliantservices
http://www.hp.com/go/proliant/carepack
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
Page 11
QuickSpecs
HP ProLiant DL180 Generation 6
HPC Interconnects
NOTE: High Performance Computing (HPC) interconnect technologies are available for the DL165 G6 under the Cluster
Platform product portfolio. These high-speed interconnects are fully supported by HP when they are part of these configure
to order clusters. Solutions can be defined with a lot of flexibility with the help of configuration tools. Please visit the
following URL to configure HPC Clusters with InfiniBand, Gigabit Ethernet or Myrinet Interconnects:
http://www.hp.com/techservers/clusters/ucp/index.html
HPC Interconnects
InfiniBand
Gigabit Ethernet
Myrinet XP
PCI-X and PCI-Express adapters
Use embedded ports or optional 10GbE NICs
PCI-X Rev D, Rev E and Rev F adapters
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
Page 12
QuickSpecs
HP ProLiant DL180 Generation 6
Models
Four Drive Serial ATA (SATA) Models
NOTE: Upgrading from 4 Non-Hot Plug SATA hard drives to 4 Hot Plug SATA/SAS hard drives requires the addition of a
storage controller and one Internal mini-SAS cable (496013-B21).
NOTE: Upgrading to 8 Hot Plug SATA/SAS hard drives requires the addition of a HP 2U G6 8HDD LFF DL18X KIT
(506924-B21), storage controller (Smart Array P410/256MB recommended), and two Internal SATA/SAS cables (mini-SAS
cable (496013-B21).
HP DL180G6 E5504
Processor
Intel® Xeon® Processor E5504 (2.00 GHz, 4MB L3 Cache, 80W,
2x2GB 4LFF
One of the following
DDR3-800)
487502-xx1
depending on model
Intel® Xeon® Processor L5520 (2.26 GHz, 8MB L3 Cache, 60W,
DDR3-1066, HT, Turbo 1/1/2/2)
HP DL180G6 L5520
Cache Memory
4MB shared L3 cache (E5504)
2x2GB 4LFF
One of the following
8MB shared L3 cache (L5520)
487506-xx1
depending on model
Memory
4GB (2 x 2GB) PC3-10600E (UDIMM)
Network Controller
HP NC362i Integrated Dual Port Gigabit Server Adapter
Storage Controller
Embedded SATA Raid Standard RAID 0,1,10
Hard Drive
1x 160GB Hot Plug SATA
NOTE: Hot-plug functionality requires the addition of a Smart Array
controller.
Internal Storage
4.0TB (4 x 1TB Hot Plug 3.5" SATA hard drives), Maximum
4.0TB (4 x 1TB Hot Plug 3.5" SAS hard drives), Maximum
Optical Drive
None ship standard
Power Supply
460W common slot, high efficiency power supply
Form Factor
Rack (2U)
Eight Drive Serial ATA (SATA) Models
NOTE: Supports up to 8 Hot Plug SATA or SAS Hard Drives.
HP DL180G6 E5520
Processor
Intel® Xeon® Processor E5520 (2.26 GHz, 8MB L3 Cache, 80W,
3x2GB 8LFF
DDR3-1066, HT, Turbo 1/1/2/2)
487503-xx1
Cache Memory
8MB shared L3 cache
Memory
6GB (3 x 2GB) PC3-10600E (UDIMM)
Network Controller
HP NC362i Integrated Dual Port Gigabit Server Adapter
Storage Controller
HP Smart Array P410 /256MB Controller (RAID 0/1/1+0/5/5+0)
NOTE: A minimum of 256 MB cache, battery kit, and Smart Array
Advanced Pack License Key upgrade (P/N: 516471-B21) is required to
enable RAID 6, 6+0
Hard Drive
None ship standard
Internal Storage
8.0TB (8 x 1TB Hot Plug 3.5" SATA hard drives), Maximum
8.0TB (8 x 1TB Hot Plug 3.5" SAS hard drives), Maximum
Optical Drive
None ship standard
Power Supply
460W common slot, high efficiency power supply
Form Factor
Rack (2U)
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
Page 13
QuickSpecs
HP ProLiant DL180 Generation 6
Models
Twelve Drive Serial ATA (SATA) Models
NOTE: Internal Storage expandable to 14 SAS/SATA drives with 2 Rear Drive Option Kit (488234-B21)
HP DL180G6 E5540
Processor
(2) Intel® Xeon® Processor E5540 (2.53 GHz, 8MB L3 Cache, 80W,
6x2GB 12LFF US
One of the following
DDR3-1066, HT, Turbo 1/1/2/2)
487507-xx1
depending on model
Intel® Xeon® Processor E5520 (2.26 GHz, 8MB L3 Cache, 80W,
DDR3-1066, HT, Turbo 1/1/2/2)
HP DL180G6 E5520
Cache Memory
8MB shared L3 cache
3x2GB 12LFF
Memory
E5540: 12GB (6 x 2GB) PC3-10600R (RDIMM)
487508-xx1
One of the following
E5520: 6GB (3 x 2GB) PC3-10600E (UDIMM)
depending on model
Network Controller
HP NC362i Integrated Dual Port Gigabit Server Adapter
Storage Controller
HP Smart Array P212 /256MB Controller (RAID 0/1/1+0/5/5+0)
NOTE: The minimum of 256 MB cache, battery kit, and Smart Array
Advanced Pack License Key upgrade (P/N: 516471-B21) is required to
enable RAID 6, 6+0
Hard Drive
None ship standard (up to 12 Hot Plug SATA or SAS drives supported)
Internal Storage
12.0TB (12 x 1TB Hot Plug 3.5" SATA hard drives), Maximum
12.0TB (12 x 1TB Hot Plug 3.5" SAS hard drives), Maximum
NOTE: Internal Storage expandable to 14 SAS/SATA drives with 2 Rear
Drive Option Kit (488234-B21)
Optical Drive
None ship standard
Power Supply
750W common slot, high efficiency power supply
Form Factor
Rack (2U)
Country Code Key
xx = 00
xx = 29
xx = 37
xx = 42
xx = AA
U.S.
Japan
APD
Europe
PRC
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
Page 14
QuickSpecs
HP ProLiant DL180 Generation 6
Configuration Information - Factory Integrated Models
NOTE: This section lists some of the steps required to configure a Factory Integrated Model. To ensure only valid
configurations are ordered, HP recommends the use of an HP approved configurator. Contact your local sales
representative for information on CTO product offerings and requirements.
NOTE: HP does not allow factory integration of options into standard models listed above.
Configure-to-order servers must start with a CTO Chassis.
NOTE: FIO indicates that this option is a Factory Installable Option.
Step 1: Base Configuration (choose one of the following configurable models)
Hot Plug Models
HP ProLiant DL180 G6 Hot Plug SAS/SATA Rack CTO Chassis
Factory Integrated Model ships with:
HP NC362i Integrated Dual Port Gigabit Server Adapter
Three available PCI-Express slots:
Slot 1: x16 low-profile/half-height slot
Slot 2 & 3: x8 full-height/full length
NOTE: Optional PCI-X option kit includes: Slot 1 and 2: full-length/full-height
PCI-X 100. PCI-X slots are 64 bits; 133 MHz capable if only one PCI-X card is
installed in the server.
NOTE: Optional FL/FH option kit includes: Slot 1: full length/full height slot.
One HP SATA Embedded Cable Kit
One Highline IEC Power Cord
4 Non-Hot Plug Fans
Rack (2U), (3.5 in/8.89 cm)
Tool-less Fixed Rails
507168-B21
Step 2: Choose Required Options (only one of the following from each list unless
otherwise noted)
Processors
Quad-Core Processors
Intel® Xeon® processor L5520 (2.26 GHz, 8MB L3 Cache, 60W, DDR3-1066,
HT, Turbo 1/1/2/2), FIO Base
NOTE: If 2 processors are desired, select one 508344-L21 and one 508344B21.
Intel® Xeon® processor E5540 (2.53 GHz, 8MB L3 Cache, 80W, DDR3-1066,
HT, Turbo 1/1/2/2), FIO Base
NOTE: If 2 processors are desired, select one 508343-L21 and one 508343B21.
Intel® Xeon® processor E5520 (2.26 GHz, 8MB L3 Cache, 80W, DDR3-1066,
HT, Turbo 1/1/2/2), FIO Base
NOTE: If 2 processors are desired, select one 508342-L21 and one 508342B21.
Intel® Xeon® processor E5504 (2.00 GHz, 4MB L3 Cache, 80W, DDR3-800),
FIO Base
NOTE: If 2 processors are desired, select one 508341-L21 and one 508341B21.
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
508344-L21
508343-L21
508342-L21
508341-L21
Page 15
QuickSpecs
HP ProLiant DL180 Generation 6
Configuration Information - Factory Integrated Models
Memory
Registered RDIMMs
HP 2GB 2Rx8 PC3-10600R-9 Kit
HP 4GB 2Rx4 PC3-10600R-9 Kit
HP 4GB 4Rx8 PC3-8500R-7 LP Kit
HP 8GB 2Rx4 PC3-8500R-7 Kit
Unregistered with ECC UDIMMs
HP 1GB 1Rx8 PC3-10600E-9 Kit
HP 2GB 2Rx8 PC3-10600E-9 Kit
NOTE: All DDR3 memory option kits consist of one DIMM per kit. For detailed
memory configuration rules and guidelines, please use the Online DDR3
Memory Configuration Tool: www.hp.com/go/ddr3memory-configurator.
NOTE: Kits described as LP include Low Power DIMMs. For more information on
ProLiant Energy Efficient Features, see:
http://h18004.www1.hp.com/products/servers/platforms/energyefficient/
NOTE: There is a maximum support limitation of 8 ranks per memory channel
(maximum of 2 quad rank DIMMs per channel)
Hard Drive Cage
HP 2U G6 4HDD CAGE Kit, FIO
HP 2U G6 8HDD CAGE Kit, FIO
HP 2U G6 12HDD CAGE Kit, FIO
HP 2U 8SFF HDD CAGE & BKPLN G6 FIO
HP 2U G6 25 SFF CAGE FIO Kit
Power Supply
NOTE: Many HP ProLiant Servers now offer new power options, including
Common Slot Power Supplies. These power supplies come in multiple power
ratings and higher efficiency levels to offer the Right Size solution to fit your
configuration. This provides improved power delivery and the advantage of
reclaiming lost power. Prior to making a power supply selection it is "highly
recommended" that the "HP Power Advisor" is run to determine the right size
power supply for your server configuration. The HP Power Advisor is located at:
www.hp.com/go/proliant-energy-efficient
HP 460W CS HE Power Supply Kit
HP 750W CS HE Power Supply Kit
CAUTION: Optional Power Supplies used for Redundancy "MUST" match the
original supplied power supply. Upgrades for more power headroom, when
replacing the original power supplies must match if purchased for redundancy.
Option Kits contain optional power supply, an IEC power cable and PDU IEC
cables. In ProLiant Servers that have more than one power slot (bay), only same
size power supplies are recommended. If non-matched power supplies are
inserted you will get errors and operation will fail.
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
500656-B21
500658-B21
500660-B21
516423-B21
500668-B21
500670-B21
506926-B21
506927-B21
506928-B21
534958-B21
516011-B21
503296-B21
512327-B21
Page 16
QuickSpecs
HP ProLiant DL180 Generation 6
Configuration Information - Factory Integrated Models
Step 3: Choose Additional Factory Integratable Options (only one from each list
unless otherwise noted)
Rear DVD Kit
Storage Controller
Redundant Power
Supply
HP DL180G6 Rear DVD Cage Kit
NOTE: The x16 low profile slot is not available when this option is configured.
HP P410/ZM FIO Smart Array Controller
HP P411/256 FIO SA Cntrlr w/Battery
HP P410/256 FIO SA Cntrlr w/Battery
HP P212/256 FIO SA Cntrlr w/Battery
HP 460W CS HE Power Supply Kit
HP 750W CS HE Power Supply Kit
CAUTION: Optional Power Supplies used for Redundancy "MUST" match the
original supplied power supply. Upgrades for more power headroom, when
replacing the original power supplies must match if purchased for redundancy.
Option Kits contain optional power supply, an IEC power cable and PDU IEC
cables. In ProLiant Servers that have more than one power slot (bay), only same
size power supplies are recommended. If non-matched power supplies are
inserted you will get errors and operation will fail.
515826-B21
462860-B21
491193-B21
491195-B21
491191-B21
503296-B21
512327-B21
Step 4: Choose Additional Options for Factory Integration
NOTE: For additional options, please refer to the "Core Options" and "Additional Options" sections below.
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
Page 17
QuickSpecs
HP ProLiant DL180 Generation 6
Core Options
NOTE: Some options may not be available for factory integration. Please contact an HP sales representative for additional
information.
Unique Options
HP DL180G6 Redundant Fan Kit
516009-B21
HP Dedicated Management Port Kit
516006-B21
HP Internal USB Cable G6 Kit
536769-B21
NOTE: This option required to connect a USB device internally.
HP DL180 G6 3PCI-E x8, Full Height Kit
577668-B21
NOTE: This option provides two x8 full-length/full-height slots as well as an
additional x8 (x4 electrically) slot. This allows the DL180G6 to have a maximum
of four (4) slots.
HP PCI-X Full Riser DL180 G6 Kit
488230-B21
NOTE: This option kit replaces the three internal expansion slots listed in step 1
base configuration.
NOTE: Optional PCI-X option kit includes: Slot 1: full-length/full-height PCI-X
100; Slot 2: Full length/Full-height PCI-X 100. PCI-X slots are 64 bits; 133 MHz
capable if only one PCI-X card is installed in the server.
HP 2U G6 8HDD LFF DL18X KIT
506924-B21
NOTE: Upgrading to 8 Hot Plug SATA/SAS hard drives requires the addition of a
storage controller (Smart Array P410/256MB recommended), two Internal
ATA/SAS cables, (mini-SAS cable (496013-B21).
HP DL180G6 Rear 2LFF Kit
488234-B21
NOTE: Supports 12 hard drive server models only. Hard Drives not included.
NOTE: This option replaces the 2 Full Length, Full Height x8 PCIe slots.
HP KIT 2PCI-E x8, FH, DL180G6
497145-B21
NOTE: This option provides 2 Full Length, Full Height x8 PCIe slots.
HP KIT PCI-E x16, DL180G6
497143-B21
NOTE: This option replaces the 2 Full Length, Full Height x8 PCIe slots.
Processor
Quad-Core Processors
Intel® Xeon® Processor L5520 (2.26 GHz, 8MB L3 Cache, 60W, DDR3-1066,
HT, Turbo 1/1/2/2)
Intel® Xeon® Processor E5540 (2.53 GHz, 8MB L3 Cache, 80W, DDR3-1066,
HT, Turbo 1/1/2/2)
Intel® Xeon® Processor E5520 (2.26 GHz, 8MB L3 Cache, 80W, DDR3-1066,
HT, Turbo 1/1/2/2)
Intel® Xeon® Processor E5504 (2.00 GHz, 4MB L3 Cache, 80W, DDR3-800)
NOTE: HT indicates that the processor model supports Intel® Hyper-Threading
Technology.
NOTE: Turbo indicates the maximum potential frequency increment when using
Intel® Turbo Boost Technology, with 4, 3, 2, and 1 cores active.
NOTE: DDR3 speed is the maximum memory speed of the processor. Actual
memory speed may depend on the quantity and type of DIMMs installed.
NOTE: For the Intel 5500 Series, the letter preceding the model number
indicates the performance/wattage of the processor. "X" denotes High
Performance/Wattage; "E" denotes Enterprise Performance/Wattage
(Mainstream); and "L" denotes Lower Wattage.
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
508344-B21
508343-B21
508342-B21
508341-B21
Page 18
QuickSpecs
HP ProLiant DL180 Generation 6
Core Options
Memory
Optical Drives
Registered RDIMMs
HP 2GB 2Rx8 PC3-10600R-9 Kit
HP 4GB 2Rx4 PC3-10600R-9 Kit
HP 4GB 4Rx8 PC3-8500R-7 LP Kit
HP 8GB 2Rx4 PC3-8500R-7 Kit
Unregistered with ECC UDIMMs
HP 1GB 1Rx8 PC3-10600E-9 Kit
HP 2GB 2Rx8 PC3-10600E-9 Kit
NOTE: All DDR3 memory option kits consist of one DIMM per kit. For detailed
memory configuration rules and guidelines, please use the Online DDR3
Memory Configuration Tool: www.hp.com/go/ddr3memory-configurator
NOTE: Kits described as LP include Low Power DIMMs. For more information on
ProLiant Energy Efficient Features, see:
http://h18004.www1.hp.com/products/servers/platforms/energyefficient/
HP Slim SATA DVD-ROM Optical Drive
HP Slim SATA DVDRW Optical Drive
500656-B21
500658-B21
500660-B21
516423-B21
500668-B21
500670-B21
481041-B21
481043-B21
NOTE: Optical drives can only be installed on 8 bay hard drive models.
Hard Drives
NOTE: The components of a storage subsystem (e.g. the drive, the
HBA/controller, and the server backplane) should operate at the same data
transfer rate or the system bandwidth will be negotiated down to an acceptable
level for all components.
SAS Hot Plug SFF Enterprise (ENT) Drives
HP 300GB 6G SAS 10K SFF DP ENT HDD
HP 300GB 3G SAS 10K SFF DP ENT HDD
HP 146GB 6G SAS 10K SFF DP ENT HDD
HP 146GB 6G SAS 15K SFF DP ENT HDD
HP 146GB 3G SAS 15K SFF DP ENT HDD
HP 146GB 3G SAS 10K SFF DP ENT HDD
HP 72GB 6G SAS 15K SFF DP ENT HDD
HP 72GB 3G SAS 15K SFF DP ENT HDD
HP 72GB 3G SAS 10K SFF DP ENT HDD
HP 36GB 3G SAS 15K SFF DP ENT HDD
SAS Hot Plug 3.5" Enterprise (ENT) Drives
NOTE: 3G Hard Drives will operate at up to 3.0 Gb/s in 4 drive models that use
the embedded controller.
HP 400GB 3G 10K 3.5" DP SAS ENT HDD
HP 450GB 3G 15K 3.5" DP SAS ENT HDD
HP 300GB 3G SAS 15K 3.5" DP HDD
HP 146GB 3G SAS 15K 3.5" DP HDD
HP 72GB 3G SAS 15K 3.5" DP HDD
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information:
http://h18000.www1.hp.com/products/quickspecs/12244_div/12244_div.html
(Worldwide)
NOTE: If selecting more than 4 hard drives or if using SAS hard drives, a Smart
Array controller and two SAS/SATA cables (P/N 464830-B21) are required.
SAS Hot Plug SFF Midline (MDL) Drives
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
507127-B21
492620-B21
507125-B21
512547-B21
504062-B21
418367-B21
512545-B21
418371-B21
384842-B21
418369-B21
459508-B21
454232-B21
416127-B21
384854-B21
384852-B21
Page 19
QuickSpecs
HP ProLiant DL180 Generation 6
Core Options
Communications
HP 500GB 6G SAS 7.2K SFF DP MDL HDD
SAS Hot Plug 3.5" Midline (MDL) Drives
NOTE: 3G Hard Drives will operate at up to 3.0 Gb/s in 4 drive models that use
the embedded controller.
HP 1TB 3G SAS 7.2K 3.5" DP MDL HDD
HP 750GB 3G SAS 7.2K 3.5" DP MDL HDD
SATA Hot Plug SFF Midline (MDL) Drives
HP 500GB 3G SATA 7.2K 2.5in MDL HDD
HP 160GB 3G SATA 7.2K 2.5in MDL HDD
SATA Hot Plug 3.5" Midline (MDL) Drives
HP 1TB 3G SATA 7.2K 3.5" MDL HDD
HP 750GB 3G SATA 7.2K 3.5" MDL HDD
HP 500GB 3G SATA 7.2K 3.5" MDL HDD
HP 250GB 3G SATA 7.2K 3.5" MDL HDD
SATA Hot Plug 3.5" Entry (ETY) Drives
HP 160GB 3G SATA 7.2K 3.5" ETY HDD
NOTE: SATA drives have a 1 year warranty. Please see the QuickSpecs for
Technical Specifications and additional specifications:
http://h18000.www1.hp.com/products/quickspecs/13021_div/13021_div.html
(Worldwide)
507610-B21
HP NC112T PCIe Gigabit Server Adapter
HP NC360T PCI Express Dual Port Gigabit Server Adapter
HP NC364T PCI Express Quad Port Gigabit Server Adapter
NOTE: Does not support Windows 2000.
HP NC373F PCI Express Multifunction Gigabit Server Adapter
HP NC373T PCI Express Multifunction Gigabit Server Adapter
HP NC382T PCI Express Dual Port Multifunction Gigabit Server Adapter
HP NC522SFP Dual Port 10GbE Server Adapter
NOTE: A minimum of two Gigabytes (2 GB) of server memory is required per
each NC522SFP adapter.
NOTE: Direct Attach Cable (DAC) for copper environments or fiber transceivers
and cables for fiber-optic environments must be purchased separately.
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information: www.hp.com/go/ProLiantNICs.
503746-B21
412648-B21
435508-B21
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
461137-B21
461135-B21
507750-B21
530888-B21
454146-B21
458930-B21
458928-B21
458926-B21
458945-B21
394793-B21
394791-B21
458492-B21
468332-B21
Page 20
QuickSpecs
HP ProLiant DL180 Generation 6
Additional Options
Server Management HP Lights-Out 100i Advanced Pack
Stand Alone Software HP LO100i Advanced Pack, No Media 1-Server License including 1 year of 24x7
Products
Technical Support and Updates
NOTE: For additional License Kits please see the Lights-Out 100i Advanced
QuickSpecs at: www.hp.com/go/lo100.
NOTE: Flexible and volume quantity (AKA) license kits are available for the
Lights-Out 100i Advanced Pack licenses as well as Electronic License To Use
(E-LTU). AKA Tracking licenses require a 100 unit minimum forecast at initial
contract signing. For these additional part numbers, please refer to QuickSpecs
at this link for more information:
http://h18004.www1.hp.com/products/servers/management/remotemgmt.html
HP Insight Control
(ICE) suites
HP Insight Control suite for Linux (ICE-LX)
HP Insight Control for Linux, No Media, 1-Server license, including one year of
24x7 Technical Support and Updates
NOTE: This part number can be used to purchase one (1) license with a single
activation key. Customer will receive a printed license entitlement certificate via
physical shipment. The license entitlement certificate must be redeemed online
or via fax in order to obtain the license activation key(s). Includes one year of 24
x 7 HP Software Technical Support and Update Service.
NOTE: One certificate is shipped for each license.
HP Insight Control for Linux, Media pack (DVD) - No licenses included
NOTE: This optional Media pack DVD contains the ISO image for HP Insight
Control suite for Linux, HP System Insight Manager, HP Insight Power Manager,
HP Insight Virtual Machine Manager, and an integrated installer. Servers must
be acquired separately.
NOTE: This Media pack is optional because the latest ISO image and latest
updates may be downloaded at no cost from: http://www.hp.com/go/ice-linux
(click on Download button).
NOTE: For additional License Kits, including electronic licensing options, please
see the QuickSpecs at:
http://h18000.www1.hp.com/products/quickspecs/13019_div/13019_div.html
452151-B21
464423-B22
464422-B22
HP Graphic Card
Power Adapter Kit
HP Graphic Card Power Adapter Kit
533955-B21
Security
HP Trusted Platform Module Option Kit
488069-B21
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
Page 21
QuickSpecs
HP ProLiant DL180 Generation 6
Additional Options
Storage Controllers
HPC Specific Options
SAS Controllers
HP Smart Array P800
HP Smart Array P800/512 BBWC Controller
NOTE: The HP Smart Array P800 controller provides support for external
storage on the DL180G6 server. Local storage is supported on the DL180 using
either the P212 or P410 controllers.
HP Smart Array P212 Controller
HP P212/Zero Memory Smart Array Controller
HP P212/256MB Smart Array Controller
HP Smart Array P410 Controller
HP Smart Array P410/256MB Controller
HP Smart Array P410/512MB BBWC Controller
HP Smart Array P411 Controller
HP Smart Array P411/256MB Controller
HP Smart Array P411/512MB BBWC
Optional Upgrades
256 MB Cache Module
NOTE: Supported on HP Smart Array P212 Controller only.
512MB BBWC
NOTE: Supported on HP Smart Array P410 Controller and HP Smart Array P411
Controller only.
Battery Kit upgrade
NOTE: To enable BBWC on the 256MB cache.
NOTE: Supported on HP Smart Array P212 Controller, HP Smart Array P410
Controller, and HP Smart Array P411 Controller only.
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information:
http://h18000.www1.hp.com/products/quickspecs/12616_div/12616_div.html
(Smart Array P800 Controller)
http://h18000.www1.hp.com/products/quickspecs/13203_div/13203_div.html
(Smart Array P212 Controller)
http://h18000.www1.hp.com/products/quickspecs/13201_div/13201_div.html
(Smart Array P410 Controller)
http://h18000.www1.hp.com/products/quickspecs/13202_div/13202_div.html
(Smart Array P411 Controller)
SCSI HBA
HP SC11Xe Host Bus Adapter
NOTE: Recommended HBA for SCSI tape drive connect.
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information:
http://h18000.www1.hp.com/products/quickspecs/12566_div/12566_div.html
(SCSI HBA)
HP IB 4X DDR Conn-X PCI-e G2 Dual Port HCA
HP IB 4X DDR PCI-e DUAL PORT HCA
HP IB 4X QDR PCI-e G2 Dual Port HCA
NOTE: Please see the QuickSpecs for additional information:
http://h18000.www1.hp.com/products/quickspecs/13078_div/13078_div.html
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
381513-B21
462828-B21
462834-B21
462862-B21
462864-B21
462830-B21
462832-B21
462968-B21
462967-B21
462969-B21
412911-B21
483514-B21
448397-B21
517721-B21
Page 22
QuickSpecs
HP ProLiant DL180 Generation 6
Additional Options
Tape Storage
NOTE: For the complete listing of Tape Drive offerings, please see:
http://www.hp.com/products1/storage/compatibility/tapebackup/ISS/index.html
Tape Drives
USB Rack-Mount Tape Solutions
HP StorageWorks 1U USB Rack-Mount Kit with one DAT 160 USB Tape Drive
NOTE: Pre-configured with one DAT 160 USB tape drive.
SAS Rack-Mount Tape Solutions
NOTE: HP recommends purchasing the HP Smart Array P212 (462828-B21) for
a dedicated SAS HBA for tape.
HP StorageWorks 1U SAS Rack-Mount Kit with one LTO-4 Ultrium 1760
NOTE: Pre-configured with one LTO-4 Ultrium 1760 SAS tape drive.
HP StorageWorks 1U SAS Rack-Mount Kit
NOTE: Supports up to (2) half-height SAS tape drives.
HP StorageWorks LTO-2 Ultrium 448 SAS Internal Tape Drive
NOTE: Mounts inside the 1U SAS Rack-Mount Kit (AE459A).
HP StorageWorks LTO-3 Ultrium 920 SAS Internal Tape Drive
NOTE: Mounts inside the 1U SAS Rack-Mount Kit (AE459A).
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information:
http://h18000.www1.hp.com/products/quickspecs/10854_div/10854_div.html
(Worldwide)
For an up-to-date listing of the latest O/S and software support details for HP
Ultrium tape drives, please visit: http://www.hp.com/go/connect.
Tape Autoloaders
HP StorageWorks 1/8 G2 Tape Autoloader
HP StorageWorks 1/8 G2 LTO-4 Ultrium 1760 SAS Tape Autoloader
HP StorageWorks 1/8 G2 LTO-3 Ultrium 920 SAS Autoloader
HP StorageWorks 1/8 G2 Tape Autoloader Rack Kit
NOTE: Required to install the 1/8 G2 Autoloaders in a standard 19-inch rack;
includes rails and rackmount instructions.
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information: http://www.hp.com/go/automation needed to create a complete
solution; reference current compatibility information at:
http://www.hp.com/go/ebs.
Tape Libraries
HP StorageWorks MSL2024 Tape Library
HP StorageWorks MSL2024 1 LTO-4 Ultrium 1760 SAS Drive Library
HP StorageWorks MSL2024 1 LTO-3 Ultrium 920 SAS Drive Library
HP StorageWorks MSL4048 Tape Library
HP StorageWorks MSL4048 2 LTO-4 Ultrium 1760 SAS Drive Library
HP StorageWorks MSL4048 1 LTO-3 Ultrium 920 SAS Drive Library
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information: http://www.hp.com/go/automation needed to create a complete
solution; reference current compatibility information at:
http://www.hp.com/go/ebs.
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
AG703A
EH946A
AE459A
DW085A
EH847A
AK377A
AH558A
AK378A
AH559A
AK380A
AH560A
Page 23
QuickSpecs
HP ProLiant DL180 Generation 6
Additional Options
Disk-Based Backup
RDX Removable Disk Backup
HP StorageWorks RDX500 External Removable Disk Backup System
NOTE: 500GB of Disk Storage.
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information:
http://h18000.www1.hp.com/products/quickspecs/13036_div/13036_div.html
HP D2D Backup System
HP StorageWorks D2D2502i Backup System
NOTE: 2 TB raw capacity/1.5 TB useable capacity.
HP StorageWorks D2D2504i Backup System
NOTE: 4 TB raw capacity/3 TB useable capacity.
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information: http://www.hp.com/go/d2d.
AJ935A
EJ001A
EJ002A
StorageWorks Options NOTE: The following is a list of all Fibre Channel Host Bus Adapters for
Windows and Linux. For detailed compatibility information please see:
http://h18006.www1.hp.com/storage/saninfrastructure/hba.html.
StorageWorks Fibre Channel HBA
HP StorageWorks FC1143 4Gb PCI-X 2.0 FC HBA
HP StorageWorks FC1243 4Gb PCI-X 2.0 Dual Channel FC HBA
HP StorageWorks FC2142SR 4Gb PCI-e FC HBA
HP StorageWorks FC2242SR Dual Channel 4Gb PCI-e FC HBA
HP StorageWorks FC1142SR 4Gb PCI-e FC HBA
HP StorageWorks FC1242SR Dual Channel 4 Gb PCI-e FC HBA
HP StorageWorks FC2143 4Gb PCI-X 2.0 FC HBA
HP StorageWorks FC2243 4Gb PCI-X 2.0 Dual Channel FC HBA
HP StorageWorks 81E 8Gb Single Port PCI-e FC HBA
HP StorageWorks 82E 8Gb Dual Port PCI-e FC HBA
HP StorageWorks 82Q 8Gb Dual Port PCI-e FC HBA
HP StorageWorks 81Q 8Gb Single Port PCI-e FC HBA
StorageWorks SCSI HBA
HP U320e SCSI Host Bus Adapter
NOTE: Recommended for MSL SCSI Tape Library connect.
HP StorageWorks
Modular Smart Array
MSA SAN Storage Arrays
HP StorageWorks 50 Modular Smart Array
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information:
http://h18000.www1.hp.com/products/quickspecs/12245_div/12245_div.html
(Worldwide)
HP StorageWorks MSA60 Array
NOTE: Please see the QuickSpecs for additional options and configuration
information at:
http://h18000.www1.hp.com/products/quickspecs/12627_div/12627_div.html
HP StorageWorks MSA70 Array
NOTE: Please see the QuickSpecs for additional options and configuration
information at:
http://h18000.www1.hp.com/products/quickspecs/12652_div/12652_div.html
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
AB429A
AE369A
A8002A
A8003A
AE311A
AE312A
AD167A
AD168A
AJ762A
AJ763A
AJ764A
AK344A
AH627A
364430-B21
418408-B21
418800-B21
Page 24
QuickSpecs
HP ProLiant DL180 Generation 6
Additional Options
Uninterruptible Power HP Tower UPS
Systems
HP T1000v Uninterruptible Power System
HP T1000v UPS
NOTE: The T1000v is available in China and India only.
NOTE: Please see QuickSpecs for Technical Specifications and additional
information:
http://h18000.www1.hp.com/products/quickspecs/13130_div/13130_div.html
(Worldwide)
HP Rack-mountable UPS
HP R1.5 VA 1U UPS NA
HP R1.5 VA 1U UPS INTL
HP, R1.5kVA UPS, 1U, JPN/TW
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information:
http://h18000.www1.hp.com/products/quickspecs/12507_div/12507_div.html
(Worldwide)
HP R3000v UPS Uninterruptible Power System
HP R3000v UPS
NOTE: The R3000v is available in China and India only.
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information:
http://h18000.www1.hp.com/products/quickspecs/13129_div/13129_div.html
(Worldwide)
HP Rack Series
Rack Kits
HP Rack 10000 G2 Series (Carbon/Graphite Metallic)
10642 G2 (42U) Rack Cabinet 1200mm Deep - Shock Pallet
10642 G2 (42U) Rack Cabinet 1200mm Deep - Pallet
10647 G2 (47U) Rack Cabinet 1200mm Deep - Shock Pallet
10647 G2 (47U) Rack Cabinet 1200mm Deep - Pallet
NOTE: It is mandatory to use a shock pallet when shipping racks with equipment
installed.
NOTE: Please see the Rack 10000 G2 QuickSpecs for Technical Specifications
such as height, width, depth, weight, and color:
http://h18000.www1.hp.com/products/quickspecs/12402_div/12402_div.html
(Worldwide)
NOTE: For additional information regarding Rack Cabinets, please see the
following URL: http://www.hp.com/go/rackandpower.
HP Rack Cable Management Velcro Clips
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
AF443A
AF419A
AF418A
AF421A
AF444A
AF034A
AF038A
AF044A
AF045A
379820-B21
Page 25
QuickSpecs
HP ProLiant DL180 Generation 6
Additional Options
HP Rack Options
HP KVM Switch Options
2x1x16 IP Console Switch with Virtual Media
4x1x16 IP Console Switch with Virtual Media
2x16 Server Console Switch with Virtual Media
PS/2 Virtual Media Interface Adapter, 1 pack
NOTE: Requires PS/2 and one USB port on server.
PS/2 Interface Adapter, 1 pack
PS/2 Interface Adapter, 8 pack
HP 1x4 Console Switch
HP PS2 Server Console Cable, 6 foot, 2-Pack
HP USB Server Console Cable, 6 foot, 2-Pack
NOTE: required for supporting USB peripherals.
NOTE: Cat5e cables are required to connect Interface Adapters to Console
Switches. Cat5e cables can be found at the following URL:
http://www.hp.com/go/kvm.
HP Serial Console Server Options
HP 16 Port Serial Console Server (worldwide)
HP 48 Port Serial Console Server (worldwide)
Serial Adapter, RJ45-DB9 DCE Female, 1 Pack
Serial Adapter, RJ45-DB9 DCE Female, 8 Pack
NOTE: Cat5e cables are required to connect Serial Adapters to Serial Console
Servers. Additional Serial Adapters and Cat5e cables can be found at the
following URL: http://www.hp.com/go/kvm.
NOTE: For additional information regarding KVM switches, Serial Console
servers, rack mount monitors, keyboards and all related options please see the
following URL: http://www.hp.com/go/kvm.
USB Options
USB 1.44-MB External Diskette Drive
USB Floppy Drive
HP USB-PS/2 Mouse
HP Keyboard (USB) standard 2004
Service and Support
Offerings (HP Care
Pack Services)
Hardware Services 4-Hour On-site Service
13-Hour x 5-Day Coverage, 3 Years, Electronic
24-Hour x 7-Day Coverage, 3 Years, Electronic
Hardware Services Next Business Day On-Site Service
9-Hour x 5-Day Coverage, 3 Years, Electronic
Hardware Services 6-Hour Call to Repair On-Site Service
6-Hour Call to Repair, On-site Service, 7-Day x 24-Hour Coverage, 3 Years,
Electronic
Hardware Installation, Electronic
NOTE: For more information, customer/resellers can contact:
http://www.hp.com/services/carepack.
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
AF601A
AF602A
AF600A
AF604A
262588-B21
262587-B21
AF611A
AF612A
AF613A
AF101A
AF102A
AF103A
AF110A
DC141B
DC361B
DC369A
DT528A#xxx
UH271E
UH272E
UH270E
UH273E
UH301E
Page 26
QuickSpecs
HP ProLiant DL180 Generation 6
Memory
NOTE: Memory configurations listed do not apply to "Factory Integrated Models".
HP ProLiant DL180 G6
Standard Memory (depending on model)
4 GB (2 x 2 GB) PC3-10600E Unbuffered memory, with Advanced ECC Capabilities Memory installed.
6 GB (3 x 2 GB) PC3-10600E Unbuffered memory, with Advanced ECC Capabilities Memory installed.
12 GB (6 x 2 GB) PC3-10600R Registered memory, with Advanced ECC Capabilities Memory installed.
Maximum Memory
Up to 96 GB memory is available with the optional installation of PC3-10600 Registered DIMM memory kits.
NOTE: Charts do not represent all possible memory configurations.
DDR3 memory population guidelines
For detailed memory configuration rules and guidelines, please use the Online DDR3 Memory Configuration Tool:
www.hp.com/go/ddr3memory-configurator
Some DIMM installation guidelines are summarized below:
For servers with twelve (12) memory slots
There are three (3) channels per processor; six (6) channels per server
There are two (2) DIMM slots for each memory channel; twelve (12) total slots
Memory channel 1 consists of the two (2) DIMMs that are closest to the processor
Memory channel 3 consists of the two (2) DIMMs that are furthest from the processor
DIMM slots that are white should be populated first
Do not mix Unbuffered memory (UDIMMs) with Registered memory (RDIMMs)
Do not install DIMMs if the corresponding processor is not installed
If only one processor is installed in a 2CPU system, only half of the DIMM slots are available
To maximize performance, balance the total memory capacity between all installed processors
It is not required, but it is recommended to load the channels similarly if possible
You can only have up to eight (8) ranks installed per channel
You can only install two quad-rank DIMMs per channel
You can only install two UDIMMs per channel; if available, the third slot in the channel must remain empty
Populate DIMMs from heaviest load (quad-rank) to lightest load (single-rank) within a channel
Heaviest load (DIMM with most ranks) within a channel goes furthest from the chipset
For memory mirroring mode, channel 3 must be unpopulated. Channels 1 and 2 are populated identically
For lock-step mode, channel 3 must be unpopulated. DIMMs in channels 1 and 2 will be installed in pairs. The paired
slots will be 1,4; 2,5; 3;6 on a 3DPC system or 1,4; 2,5; on a 2DPC system
No mixing DIMM voltage; all DIMMs must be the same voltage
DIMM Type ->
DIMM Rank ->
DIMM Capacity ->
DIMM Native Speed (MHz) ->
Registered DIMMS (RDIMMs)
2GB
1333
Dual Rank (2R)
4GB
8GB
1333
1066
8GB
1333
Unbuffered with ECC
DIMMs (UDIMMs)
Quad Rank Single
Dual Rank
(4R)
Rank (1R)
(2R)
4GB
1GB
2GB
1066
1333
1333
SLOTS THAT CAN BE POPULATED
12 slot servers
12
12
12
12
12
12
12
MAXIMUM CAPACITY (GB)
12 slot servers
48
96
96
48
12
24
1333
1066
1066
1066
1333
1333*
800
800
800
1066
800
not
supported
1333
1066
not
supported
1333
1066
not
supported
24
POPULATED DIMM SPEED (MHz)
1 DIMM Per Channel
1333
2 DIMM Per Channel
1066
3 DIMM Per Channel
800
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
Page 27
QuickSpecs
HP ProLiant DL180 Generation 6
Memory
* - supported with ROM update via ROM Based Setup Utility (RBSU)
NOTES:
Mixing DIMM speeds is allowed, but the system processor speed rules always override the DIMM capabilities.
If you do mix DIMM speeds, the memory bus will default to the minimum clock rate of all DIMMs in the system - even if
the slower DIMM is on the other processor.
If you install 1x 1066MHz DIMM in channel 1 and 1x 1333MHz DIMM in channel 2, you still run at 1066MHz.
If you install 1x 1066MHz DIMM in channel 1 and 5x 1333MHz DIMMs with 1 DIMM Per Channel (DPC) in each of the
other channels, you run at 1066MHz.
If you install 3DPC in one channel (if applicable) and 1DPC in all other channels, you run at 800MHz.
95 Watt CPU's are required for 1333MHz DIMM speeds. All other CPU's are capable of up to 1066MHz.
References to the above MHz speeds are for the various speeds of DDR3 DIMMs; 1333 refers to DDR3-1333, etc.
DIMM slot and configuration diagrams
Basic memory slot & population diagram
Population order; start with "A" first, "B" second, "C" third, etc.
Chnl 1
slot #
1
2
12 DIMM SLOTS (6 per CPU node)
CPU1
CPU2
population order
slot #
population order
D
1
D
A
2
A
Chnl 1
Chnl 2
3
4
E
B
3
4
E
B
Chnl 2
Chnl 3
5
6
F
C
5
6
F
C
Chnl 3
Standard memory configuration (1 CPU model)
6GB, consisting of three (3) 2GB dual-rank PC3-10600 RDIMMs
Chnl 1
slot #
1
2
CPU1
population order
D: empty
A: 2GB DIMM
slot #
1
2
CPU2
population order
D: empty
A: empty
Chnl 1
Chnl 2
3
4
E: empty
B: 2GB DIMM
3
4
E: empty
B: empty
Chnl 2
Chnl 3
5
6
F: empty
C: 2GB DIMM
5
6
F: empty
C: empty
Chnl 3
Standard memory plus optional memory (1 CPU model)
30GB, consisting of three (3) 2GB RDIMMs plus three (3) 8GB RDIMMs
3x 2GB dual-rank PC3-10600 RDIMMs
3x 8GB dual-rank PC3-8500 RDIMMs
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
Page 28
QuickSpecs
HP ProLiant DL180 Generation 6
Memory
Chnl 1
slot #
1
2
CPU1
population order
D: 8GB DIMM
A: 2GB DIMM
slot #
1
2
CPU2
population order
D: empty
A: empty
Chnl 1
Chnl 2
3
4
E: 8GB DIMM
B: 2GB DIMM
3
4
E: empty
B: empty
Chnl 2
Chnl 3
5
6
F: 8GB DIMM
C: 2GB DIMM
5
6
F: empty
C: empty
Chnl 3
Standard memory replaced with optional memory (1 CPU model)
RDIMM maximum configuration
48GB, consisting of six (6) 8GB dual-rank PC3-8500 RDIMMs
Chnl 1
slot #
1
2
CPU1
population order
D: 8GB DIMM
A: 8GB DIMM
slot #
1
2
CPU2
population order
D: empty
A: empty
Chnl 1
Chnl 2
3
4
E: 8GB DIMM
B: 8GB DIMM
3
4
E: empty
B: empty
Chnl 2
Chnl 3
5
6
I: 8GB DIMM
C: 8GB DIMM
5
6
I: empty
C: empty
Chnl 3
UDIMM maximum configuration (1 CPU model)
12GB, consisting of six (6) 2GB dual-rank PC3-10600 UDIMMs
Chnl 1
slot #
1
2
CPU1
population order
D: 2GB DIMM
A: 2GB DIMM
slot #
1
2
CPU2
population order
D: empty
A: empty
Chnl 1
Chnl 2
3
4
E: 2GB DIMM
B: 2GB DIMM
3
4
E: empty
B: empty
Chnl 2
Chnl 3
5
6
F: 2GB DIMM
C: 2GB DIMM
5
6
F: empty
C: empty
Chnl 3
Standard memory replaced with optional memory (2 CPU model)
RDIMM maximum configuration
96GB, consisting of twelve (12) 8GB dual-rank PC3-8500 RDIMMs
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
Page 29
QuickSpecs
HP ProLiant DL180 Generation 6
Memory
Chnl 1
slot #
1
2
CPU1
population order
D: 8GB DIMM
A: 8GB DIMM
slot #
1
2
CPU2
population order
D: 8GB DIMM
A: 8GB DIMM
Chnl 1
Chnl 2
3
4
E: 8GB DIMM
B: 8GB DIMM
3
4
E: 8GB DIMM
B: 8GB DIMM
Chnl 2
Chnl 3
5
6
F: 8GB DIMM
C: 8GB DIMM
5
6
F: 8GB DIMM
C: 8GB DIMM
Chnl 3
UDIMM maximum configuration (2 CPU model)
24GB, consisting of twelve (12) 2GB dual-rank PC3-10600 UDIMMs
Chnl 1
slot #
1
2
CPU1
population order
D: 2GB DIMM
A: 2GB DIMM
slot #
1
2
CPU2
population order
D: 2GB DIMM
A: 2GB DIMM
Chnl 1
Chnl 2
3
4
E: 2GB DIMM
B: 2GB DIMM
3
4
E: 2GB DIMM
B: 2GB DIMM
Chnl 2
Chnl 3
5
6
F: 2GB DIMM
C: 2GB DIMM
5
6
F: 2GB DIMM
C: 2GB DIMM
Chnl 3
NOTE: Capacity references are rounded to the common Gigabyte values.
1GB = 1024MB
2GB = 2048MB
4GB = 4096MB
8GB = 8192MB
For detailed memory configuration rules and guidelines, please use the Online DDR3 Memory Configuration Tool:
www.hp.com/go/ddr3memory-configurator
Memory
Registered RDIMMs
HP 2GB 2Rx8 PC3-10600R-9 Kit
HP 4GB 2Rx4 PC3-10600R-9 Kit
HP 4GB 4Rx8 PC3-8500R-7 LP Kit
HP 8GB 2Rx4 PC3-8500R-7 Kit
Unregistered with ECC UDIMMs
HP 1GB 1Rx8 PC3-10600E-9 Kit
HP 2GB 2Rx8 PC3-10600E-9 Kit
NOTE: All DDR3 memory option kits consist of one DIMM per kit. For detailed
memory configuration rules and guidelines, please use the Online DDR3
Memory Configuration Tool: www.hp.com/go/ddr3memory-configurator.
NOTE: Kits described as LP include Low Power DIMMs. For more information on
ProLiant Energy Efficient Features, see:
http://h18004.www1.hp.com/products/servers/platforms/energyefficient/
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
500656-B21
500658-B21
500660-B21
516423-B21
500668-B21
500670-B21
Page 30
QuickSpecs
HP ProLiant DL180 Generation 6
Storage
8 Drive Cage with DVD-Drive bay
1-8
9
Eight 3.5" Hot Plug SAS/SATA Hard Drive Bays
DVD-ROM, DVD RW
12 Drive Cage
1-12
Twelve 3.5" Hot Plug SAS/SATA Hard Drive Bays
13-14 Two Rear 3.5" Hot Plus SAS/SATA Hard Drive Bays
Not
Shown
Drive Support
Removable Media
DVD-ROM
DVD RW
Quantity
Supported
Up to 1
Up to 1
Position
Supported
9
9
Controller
Integrated IDE (ATAPI) (optional)
Integrated IDE (ATAPI) (optional)
Hard Drives
NOTE: The components of a storage subsystem (e.g. the drive, the HBA/controller, and the server backplane) should
operate at the same data transfer rate or the system bandwidth will be negotiated down to an acceptable level for all
components.
SATA Hot Plug SFF Midline (MDL) Drives
Quantity
Position
Supported
Supported Controller
500GB 3G 7.2K
Up to 8 with 8
1-8
HP Smart Array P800/512 BBWC Controller
160GB 3G 7.2K
drive cage
HP Smart Array P410/256 MB Controller
HP Smart Array P410/512 MB BBWC Controller
Up to 14 with 12
1-14
HP Smart Array P212/Zero Memory Controller
drive cage +
HP Smart Array P212/256 MB Controller
Rear Drive Cage
NOTE: Smart Array P212 Controllers recommended.
HP Smart Array P800/512 BBWC Controller
HP Smart Array P410/256 MB Controller
HP Smart Array P410/512 MB BBWC Controller
SATA Hot Plug 3.5" Midline (MDL) Drives
Quantity
Position
Supported
Supported Controller
1TB 3G 7.2K
Up to 8 with 8
1-8
HP Smart Array P800/512 BBWC Controller
750GB 3G 7.2K
drive cage
HP Smart Array P410/256 MB Controller
500GB 3G 7.2K
HP Smart Array P410/512 MB BBWC Controller
250GB 3G 7.2K
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
Page 31
QuickSpecs
HP ProLiant DL180 Generation 6
Storage
250GB 3G 7.2K
Up to 14 with 12
drive cage +
Rear Drive Cage
1-14
SATA Hot Plug 3.5" Entry (ETY) Drives
Quantity
Position
Supported
Supported
160GB 3G 7.2K
Up to 8 with 8
1-8
drive cage
Up to 14 with 12
1-14
drive cage +
Rear Drive Cage
SAS Hot Plug SFF Midline (MDL) Drives
Quantity
Position
Supported
Supported
500GB 6G SAS 7.2K
Up to 8 with 8
1-8
drive cage
Up to 14 with 12
1-12
drive cage +
Rear Drive Cage
SAS Hot Plug 3.5" Midline (MDL) Drives
Quantity
Position
Supported
Supported
1TB 3G 7.2K
Up to 8 with 8
1-8
750GB 3G 7.2K
drive cage
Up to 14 with 12
1-12
drive cage +
Rear Drive Cage
SAS Hot Plug SFF Enterprise (ENT) Drives
Quantity
Position
Supported
Supported
300GB 6G 10K
Up to 8 with 8
1-8
300GB 3G 10K
drive cage
146GB 6G 15K
146GB 3G 15K
146GB 6G 10K
Up to 14 with 12
1-12
146GB 3G 10K
drive
cage
+
72GB 6G 15K
Rear Drive Cage
72GB 3G 15K
72GB 3G 10K
36GB 3G 15K
SAS Hot Plug 3.5" Enterprise (ENT) Drives
Quantity
Position
Supported
Supported
400GB 3G 10K
Up to 8 with 8
1-8
450GB 3G 15K
drive cage
300GB 3G 15K
Up to 14 with 12
1-12
146GB 3G 15K
drive cage +
72GB 3G 15K
Rear Drive Cage
HP Smart Array P212/Zero Memory Controller
HP Smart Array P212/256 MB Controller
NOTE: Smart Array P212 Controllers recommended.
HP Smart Array P800/512 BBWC Controller
HP Smart Array P410/256 MB Controller
HP Smart Array P410/512 MB BBWC Controller
Controller
HP Smart Array P212/Zero Memory Controller
HP Smart Array P212/256 MB Controller
HP Smart Array P800/512 BBWC Controller
HP Smart Array P410/256 MB Controller
HP Smart Array P410/512 MB BBWC Controller
Controller
HP Smart Array P212/Zero Memory Controller
HP Smart Array P212/256 MB Controller
HP Smart Array P800/512 BBWC Controller
HP Smart Array P410/256 MB Controller
HP Smart Array P410/512 MB BBWC Controller
Controller
HP Smart Array P212/Zero Memory Controller
HP Smart Array P212/256 MB Controller
HP Smart Array P800/512 BBWC Controller
HP Smart Array P410/256 MB Controller
HP Smart Array P410/512 MB BBWC Controller
Controller
HP Smart Array P212/Zero Memory Controller
HP Smart Array P212/256 MB Controller
HP Smart Array P800/512 BBWC Controller
HP Smart Array P410/256 MB Controller
HP Smart Array P410/512 MB BBWC Controller
Controller
HP Smart Array P212/Zero Memory Controller
HP Smart Array P212/256 MB Controller
HP Smart Array P800/512 BBWC Controller
HP Smart Array P410/256 MB Controller
HP Smart Array P410/512 MB BBWC Controller
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
Page 32
QuickSpecs
HP ProLiant DL180 Generation 6
Storage
External Storage
50 Modular Smart Array
60 Modular Smart Array
70 Modular Smart Array
Quantity
Supported
Up to 4
Up to 4
Position
Supported
External
External
Up to 8
External
Up to 2
External
Up to 4
External
Controller
HP Smart Array P800/512 BBWC Controller
HP Smart Array P212/Zero Memory Controller
HP Smart Array P212/256 MB Controller
HP Smart Array P800/512 BBWC Controller
HP Smart Array P411/256 MB Controller
HP Smart Array P411/512 BBWC Controller
HP Smart Array P212 Zero Memory Controller
HP Smart Array P212/256 MB Controller
HP Smart Array P800/512 BBWC Controller
HP Smart Array P411/256 MB Controller
HP Smart Array P411/512 MB BBWC Controller
Tape and Disk-Based Backup
NOTE: For a complete listing of compatible tape and disk-based backup offerings, please visit: www.hp.com/go/connect.
HP StorageWorks SCSI
Tape Drives, External
LTO-1 Ultrium 232
LTO-2 Ultrium 448
LTO-3 Ultrium 920
LTO-3 Ultrium 960
LTO4 Ultrium 1760
LTO-4 Ultrium 1840
DAT 40
DAT 72
DAT 160
1U Rack-Mount Kit
3U Rack-Mount Kit
Position
Supported
External
Controller
HP SC11Xe Host Bus Adapter
Controller Part
Number
412911-B21
HP StorageWorks USB
Tape Drives, External
DAT 40 USB
DAT 72 USB
DAT 160 USB
1U USB Rack-Mount Kit
External
USB 2.0 Port
HP StorageWorks SAS
Tape Drives, External
DAT 160 SAS
LTO-2 Ultrium 448 SAS
LTO-3 Ultrium 920 SAS
LT0-4 Ultrium 1760 SAS
LTO-4 Ultrium 1840 SAS
1U Rack-Mount Kit
3U Rack-Mount Kit
External
HP Smart Array P212/Zero Memory Controller
462828-B21
HP StorageWorks SCSI
Tape Automation,
External
External
HP SC11Xe Host Bus Adapter
412911-B21
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
N/A
Page 33
QuickSpecs
HP ProLiant DL180 Generation 6
Storage
External
DAT 72x10 Autoloader
1/8 G2 Tape Autoloader
MSL2024
MSL4048
HP U320e SCSI Host Bus Adapter
NOTE: Recommended for MSL tape libraries.
AH627A
462828-B21
HP StorageWorks SAS
Tape Automation,
External
1/8 G2 Autoloader
MSL2024
MSL4048
External
HP Smart Array P212/Zero Memory Controller
HP StorageWorks Fibre
Tape Automation,
External
MSL2024
MSL4048
External
Please consult the EBS connectivity matrix at:
http://www.hp.com/go/ebs for detailed connectivity information.
N/A
HP StorageWorks RDX
Removable Disk
Backup System
RDX160
RDX320
RDX500
External
USB 2.0 Port
N/A
HP StorageWorks D2D
Backup Systems
D2D120
D2D130
D2D2500i
D2D4000i
External
Embedded Network Controller
N/A
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
Page 34
QuickSpecs
HP ProLiant DL180 Generation 6
Power Specifications
HP 460W Power Supply
Part Number - AC 460W PSU 503296-B21
Input Voltage Range (Vrms) 100 to 240
Frequency Range (Nominal) 50/60
(Hz)
Nominal Input Voltage (Vrms)
100
Maximum Rated Output Wattage
460
Nominal Input Current (A rms)
5.5
Max Rated Input Wattage Rating
526
(Watts)
Max. Rated VA (Volt-Amp)
548
Efficiency (%) at Max. Rated
87.5
Output Wattage
Power Factor
0.97
Leakage Current (mA)
0.42
Max. Inrush Current (A peak)
30
Max. Inrush Current duration
20
(mS)
Maximum British Thermal Unit
1794
Rating (BTU-Hr)
HP 750W Power Supply
Part Number - AC 750W PSU 512327-B21
Input Voltage Range (Vrms) 100 to 240
Frequency Range (Nominal) 50/60
(Hz)
Nominal Input Voltage (Vrms)
100
Maximum Rated Output Wattage
750
Nominal Input Current (A rms)
8.9
Max Rated Input Wattage Rating
857
(Watts)
Max. Rated VA (Volt-Amp)
894
Efficiency (%) at Max. Rated
87.5
Output Wattage
Power Factor
0.97
Leakage Current (mA)
0.42
Max. Inrush Current (A peak)
30
Max. Inrush Current duration
20
(mS)
Maximum British Thermal Unit
2925
Rating (BTU-Hr)
120
460
4.5
520
208
460
2.6
505
200
460
2.5
505
220
460
2.4
503
230
460
2.3
503
240
460
2.2
503
542
88.5
527
91
527
91
524
91.5
524
91.5
524
91.5
0.97
0.50
30
20
0.97
0.83
30
20
0.97
0.87
30
20
0.97
0.92
30
20
0.97
0.96
30
20
0.97
1.00
30
20
1773
1725
1725
1715
1715
1715
120
750
7.4
847
208
750
4.3
824
200
750
4.1
825
220
750
3.9
820
230
750
3.7
820
240
750
3.6
820
884
88.5
859
91
859
91
854
91.5
854
91.5
854
91.5
0.97
0.50
30
20
0.97
0.83
30
20
0.97
0.87
30
20
0.97
0.92
30
20
0.97
0.96
30
20
0.97
1.00
30
20
2892
2812
2812
2797
2797
2797
Optional Country Power Cords and Jumper Cords
WW
HP 2m 15A C20 C13 Universal Jumper Cord
Brazil
HP 1.83m 10A C13 NBR14136 Power Cord
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
AF590A
AF591A
Page 35
QuickSpecs
HP ProLiant DL180 Generation 6
Technical Specifications
System Unit
Dimensions (H x W x D) 3.45" x 17.64" x 28.23" in (8.76 x 44.80 x 71.71 cm)
(with bezel)
Weight
Maximum
45.0 lb (16.80 kg)
(approximate)
(all hard drives, power
supplies, and processors
installed)
Minimum
32.0 lb (11.94 kg)
(one hard drive, power
supply, and processor
installed)
Input Requirements
Rated Line Voltage
90 -- 132 VAC,
(per power supply)
180 - 264 V
Rated Input Current
460 Watt
7.1 A (at 120 VAC)
3.5 A (at 240 VAC)
750 Watt
7.4 A (at 120 VAC)
3.6 A (at 240 VAC)
Rated Input Frequency 50 to 60 Hz
Rated Input Power
460 & 750 watt - 852 W
BTU Rating
Power Specifications
Power Supply Output
(per power supply)
System Inlet
Temperature
Relative Humidity
Maximum
460 Watt
1773 BTU/hr (at 120
VAC)
1715 BTU/hr (at 240
VAC)
750 Watts
2892 BTU/hr (at 120
VAC)
2797 BTU/hr (at 240
VAC
To review typical system power ratings use the Power Advisor which is
available via the online tool located at URL: www.hp.com/go/proliantenergy-efficient
Click on the system of interest. Example: DL180 G6
Follow the instructions of the next screens.
Rated Steady-State
460 W (at 100 VAC)
Power
750 W (at 100 VAC)
460 W (at 200 VAC)
750 W (at 200 VAC)
Maximum Peak Power 460 W (at 100 VAC)
750 W (at 100 VAC)
460 W (at 200 VAC)
750 W (at 200 VAC)
Operating
10° to 35°C (50° to 95°F) at sea level with an
altitude derating of 1.0°C per every 305 m
(1.8°F per every 1000 ft) above sea level to a
maximum of 3050 m (10,000 ft), no direct
sustained sunlight. Maximum rate of change
is 10°C/hr (18°F/hr). The upper limit may be
limited by the type and number of options
installed.
System performance may be reduced if
operating with a fan fault or above 30°C
(86°F).
Non-operating
-30° to 60°C (-22° to 140°F). Maximum rate of
change is 20°C/hr (36°F/hr).
Operating
10 to 90% relative humidity (Rh), 28°C
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
Page 36
QuickSpecs
HP ProLiant DL180 Generation 6
Technical Specifications
(non-condensing)
Altitude
Acoustic Noise
(82.4°F) maximum wet bulb temperature, noncondensing.
Non-operating
5 to 95% relative humidity (Rh), 38.7°C
(101.7°F) maximum wet bulb temperature,
non-condensing.
Operating
3050 m (10,000 ft). This value may be limited
by the type and number of options installed.
Maximum allowable altitude change rate is
457 m/min (1500 ft/min).
Non-operating
9144 m (30,000 ft). Maximum allowable
altitude change rate is 457 m/min (1500
ft/min).
Listed are the declared A-Weighted sound power levels (LWAd) and
declared average bystander position A-Weighted sound pressure levels
(LpAm) when the product is operating in a 23°C ambient environment.
Noise emissions were measured in accordance with ISO 7779 (ECMA
74) and declared in accordance with ISO 9296 (ECMA 109).
Idle
LWAd
6.8 B
LpAm
Operating
LWAd
LpAm
50 dBA
6.8 B
50 dBA
NC362i Integrated Dual Network Interface
Port Gigabit Server
Adapter
Integrated 10/100/1000BASE-T Transceiver
Combines a triple-speed IEEE 802.3TM - Compliant Media Access
Controller (MAC) with a triple-speed Ethernet transceiver.
Data Transfer Method Compliant to x1 PCIe Specification
Network Transfer Rate 10Base-T (Half-Duplex) 10 Mb/s
10Base-T (Full-Duplex) 20 Mb/s
100Base-TX (Half100 Mb/s
Duplex)
100Base-TX (Full200 Mb/s
Duplex)
1000Base-TX (Half and 2000 Mb/s
Full-Duplex)
Connector
RJ-45
Cable Support
Performs all the physical layer functions for 10BASE-T, 100BASE-T,
and 1000BASE-T Ethernet on standard Category 5 UT
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
Page 37
QuickSpecs
HP ProLiant DL180 Generation 6
Technical Specifications
HP 160GB 3G SATA
7.2K 3.5" ETY HDD
458945-B21
160GB 7,200 rpm
Capacity
Height
Width
Depth
Interface
Transfer Rate
(Maximum)
Native Command
Queuing
Seek Time
(typical reads, including
settling)
160,041MB
1.04 in (26.4 mm)
4.36 in (110.7 mm)
7.25 in (184.2 mm)
Serial ATA
3Gb/s
Supported
Single Track
2.0 ms
Average
<11 ms
Full-Stroke
23.0 ms
Rotational Speed
7,200 rpm
Physical Configuration Bytes/Sector
512
Logical Blocks
312,581,808
Operating Temperature41° to 131° F (5° to 55° C)
Smart Array P212
Controller
Disk Drive and
Enclosure Interface
3G SAS (Serial Attached SCSI)
1.5G SATA (Serial ATA)
SAS Connectors
1 internal/1 external (Mini-SAS) x8 wide port connectors
Cache Memory Speed DDR-2/533 MHz with 40 or 72-bit wide bus provides up to 4.2 GB/s
maximum bandwidth.
Server Interface
x8 2.5G PCIe 2.0 provides 2GB/s maximum bandwidth.
SAS Speed
x8 3G SAS provides 2.4GB/s maximum bandwidth.
Cache Memory
40-bit 256MB ECC protected cache; transportable with battery-backed
upgrade.
NOTE: The 256MB cache is not battery-backed or transportable.
Logical Drives
Up to 32 logical volumes
Supported
Host Memory
64-bit, supporting greater than 4GB server memory space
Addressing
RAID Support
RAID 6, 6+0 (Advanced Data Guarding)
NOTE: A minimum of 256 MB cache, battery kit, and Smart Array
Advanced Pack License Key upgrade is required to enable RAID 6, 6+0
RAID 5, 5+0 (Distributed Data Guarding)
NOTE: The 256 MB & Battery Kit upgrade is required to enable RAID 5,
5+0 support
RAID 1, 1+0 (Striping & Mirroring)
RAID 0 (Striping)
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
Page 38
QuickSpecs
HP ProLiant DL180 Generation 6
Technical Specifications
Smart Array P410/410i Disk Drive and
Controller
Enclosure Interface
3G SAS (Serial Attached SCSI)
1.5G SATA (Serial ATA)
SAS Connectors
2 internal (Mini-SAS) x8 wide port connectors
Cache Memory Speed DDR2-533MHz with 40 or 72-bit wide bus provides up to 4.2 GB/s
maximum bandwidth.
Server Interface
x8 2.5G PCIe 2.0 provides 2GB/s maximum bandwidth
SAS Speed
x8 3G SAS provides 2.4GB/s maximum bandwidth
Cache Memory
40-bit 256MB ECC protected cache (72-bit 512MB BBWC module
upgrades available); transportable with battery-backed upgrade
Logical Drives
Up to 32 logical drives
Supported
Host Memory
64-bit, supporting greater than 4GB server memory space
Addressing
RAID Support
RAID 6, 6+0 (Advanced Data Guarding)
NOTE: The minimum of 256 MB cache, battery kit, and Smart Array
Advanced Pack License Key upgrade is required to enable RAID 6, 6+0
RAID 5, 5+0 (Distributed Data Guarding)
NOTE: The 256 MB & Battery Kit upgrade is required to enable RAID 5,
5+0 support of the Smart Array P410i
RAID 1+0 (Striping & Mirroring)
RAID 0 (Striping)
Environment-friendly
Products and
Approach
End-of-life
Management and
Recycling
Hewlett-Packard offers end-of-life HP product return, trade-in, and
recycling programs in many geographic areas. For trade-in information,
please go to: http://www.hp.com/go/green. To recycle your product,
please go to: http://www.hp.com/go/green or contact your nearest HP
sales office. Products returned to HP will be recycled, recovered or
disposed of in a responsible manner.
The EU WEEE directive (2002/95/EC) requires manufacturers to
provide treatment information for each product type for use by treatment
facilities. This information (product disassembly instructions) is posted
on the Hewlett Packard web site at: http://www.hp.com/go/green. These
instructions may be used by recyclers and other WEEE treatment
facilities as well as HP OEM customers who integrate and re-sell HP
equipment.
© Copyright 2009 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice.
Microsoft and Windows NT are US registered trademarks of Microsoft Corporation.
Intel, the Intel logo, Xeon and Xeon Inside are trademarks of Intel Corporation in the U.S. and other countries.
The only warranties for HP products and services are set forth in the express warranty statements accompanying such
products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for
technical or editorial errors or omissions contained herein.
For hard drives, 1GB = 1 billion bytes. Actual formatted capacity is less.
DA - 13248 Worldwide QuickSpecs — Version 7 — 7-13-2009
Page 39
Download PDF
Similar pages