Preface
About this Manual
• The contents of this manual and the bundled Basic Reference are subject to
change without notice.
• Note that the example screens and product illustrations shown in this User’s
Guide may differ somewhat from the screens and configuration of the actual
camera.
Copyright
This manual contains proprietary information protected by copyright. All rights
are reserved. No part of this manual may be reproduced by any mechanical,
electronic or other means, in any form, without prior written permission of the
manufacturer.
© Copyright 2015
Declaration of Conformity
This device complies with Part 15 of the FCC rules. Operation is subject to the
following conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference
that may cause undesired operation.
CE Mark Warning
This is a Class B product, in a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures.
FCC: SAR standard Value: 1.6 W/Kg, Maximal Measure: 0.27 W/Kg
CE: SAR standard Value: 2.0 W/Kg, Maximal Measure: 0.077 W/Kg
Trademark Recognition
Windows XP/Vista/Win7/Win 8 are registered trademarks of Microsoft
Corporation in the United States and/or other countries. Windows is an
abbreviated term referring to the Microsoft Windows Operation System. All
other companies or product names are trademarks or registered trademarks of
their respective companies.
1
Federal Communication Commission Interference Statement
APPLIES TO USA AND CANADA ONLY
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
This device is intended only for OEM integrators under the
following conditions:
1) The antenna must be installed such that 20 cm is maintained between the
antenna and users, and
2) The transmitter module may not be co-located with any other transmitter or
antenna.
As long as 2 conditions above are met, further transmitter test will not be
required. However, the OEM integrator is still responsible for testing their
2
end-product for any additional compliance requirements required with this
module installed.
IMPORTANT NOTE: In the event that these conditions can not be met (for
example certain laptop configurations or co-location with another transmitter),
then the FCC authorization is no longer considered valid and the FCC ID can not
be used on the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna
may be installed such that 20 cm may be maintained between the antenna and
users. The final end product must be labeled in a visible area with the following:
"Contains FCC ID: 2AAD3AA0D0". The grantee's FCC ID can be used only when
all FCC compliance requirements are met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module.
The end user manual shall include all required regulatory information/warnings
as shown in this manual.
Industry Canada statement
This device complies with RSS-210 of the Industry Canada Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable
aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux
conditions suivantes: (1) le dispositif ne doit pas produire de brouillage
préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un
brouillage susceptible de provoquer un fonctionnement indésirable.
This device is intended only for OEM integrators under the
following conditions: (For module device use)
1) The antenna must be installed such that 20 cm is maintained between the
antenna and users, and
2) The transmitter module may not be co-located with any other transmitter or
antenna.
As long as 2 conditions above are met, further transmitter tests will not be
required. However, the OEM integrator is still responsible for testing their
end-product for any additional compliance requirements required with this
module installed.
3
Cet appareil est conçu uniquement pour les intégrateurs OEM dans
les conditions suivantes: (Pour utilisation de dispositif module)
1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est
respectée entre l'antenne et les utilisateurs, et
2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou
antenne.
Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires
sur l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est
toujours responsable des essais sur son produit final pour toutes exigences de
conformité supplémentaires requis pour ce module installé.
IMPORTANT NOTE: In the event that these conditions can not be met (for
example certain laptop configurations or co-location with another transmitter),
then the Canada authorization is no longer considered valid and the IC ID can
not be used on the final product. In these circumstances, the OEM integrator
will be responsible for re-evaluating the end product (including the transmitter)
and obtaining a separate Canada authorization.
NOTE IMPORTANTE : Dans le cas où ces conditions ne peuvent être
satisfaites (par exemple pour certaines configurations d'ordinateur portable ou
de certaines co-localisation avec un autre émetteur), l'autorisation du Canada
n'est plus considéré comme valide et l'ID IC ne peut pas être utilisé sur le
produit final. Dans ces circonstances, l'intégrateur OEM sera chargé de
réévaluer le produit final (y compris l'émetteur) et l'obtention d'une autorisation
distincte au Canada.
End Product Labeling
This transmitter module is authorized only for use in this device where the
antenna may be installed such that 20 cm may be maintained between the
antenna and users. The final end product must be labeled in a visible area with
the following: "Contains IC: 10290A-AA0D0".
Plaque signalétique du produit final
Ce module émetteur est autorisé uniquement pour une utilisation dans un
dispositif où l'antenne peut être installée de telle sorte qu'une distance de 20cm
peut être maintenue entre l'antenne et les utilisateurs. Le produit final doit être
étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC:
10290A-AA0D0".
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module.
The end user manual shall include all required regulatory information/warning
as shown in this manual.
4
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à
l'utilisateur final quant à la façon d'installer ou de supprimer ce module RF dans
le manuel de l'utilisateur du produit final qui intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations
réglementaires requises et avertissements comme indiqué dans ce manuel.
Safety and Handling Precautions
Camera Information
• Do not take apart or attempt to service the camera yourself.
• Do not expose the camera to moisture, or extreme temperatures.
• Allow the camera to warm up when moving from cold to warm
temperatures.
• Do not touch and put pressure on the camera lens.
• Do not expose the lens to direct sunlight for extended periods.
• Do not use abrasive chemicals, cleaning solvents or strong detergents to
clean the product. Wipe the product with a slightly damp soft cloth.
• Do not use the flash or LED Light near a person's eyes to prevent possible
eye injury.
• Please do not use the camera while you are walking, driving or riding a
vehicle.
• Please handle the camera strap with care, and never place the strap around
the neck of an infant or child. Wrapping the strap around a neck may cause
suffocation.
• Do not subject the LCD monitor to impact.
• To prevent the risk of fire or electric shock, do not expose this appliance to
rain or moisture.
Battery Information
• Turn off the camera before installing or removing the battery.
• Use only the provided batteries or type of battery and charger that came
with your camera. Using other types of batteries or chargers may damage
the device and invalidate the warranty.
• Inserting the battery upside down can cause damage to the product and
possibly cause an explosion.
• When the camera is used for an extended period of time, it is normal for the
camera body to feel warm.
• Download all pictures and remove the battery from the camera if you are
going to store the camera for a long period of time.
5
• The type of battery and the battery power level may cause the lens to stick.
Ensure you use the correct battery type and use a fully charged battery.
• Risk of explosion if replace with an incorrect battery. Dispose of used
batteries according to the instructions.
• Please keep the batteries out of the reach of children to prevent from
swallowing batteries, which might cause poisoning.
USB adapter Information
• Do not expose the adapter to high temperatures or places with high levels of
moisture. Otherwise, it may cause fire or electric shock.
• Do not attempt to repair, disassemble, change or transform the adapter.
• Avoid sudden changes in temperature, which may cause condensation on
the adapter’s internal surfaces. Please do not use it immediately in this
situation.
• Do not touch the plug with wet hands otherwise it may cause an electric
shock.
• Do not use the travel voltage converter or AC/DC power inverter. Otherwise,
it may cause damage, overheating, malfunction or fire to the camera.
Using this Menu
Symbols used in this manual are explained below:
This indicates useful information when using your camera.
This indicates important message that should be read before using the
function.
6
Table of Contents
Preface ......................................................................................... 1
About this Manual .................................................................... 1
Federal Communication Commission Interference Statement ...... 2
Industry Canada statement ...................................................... 3
Safety and Handling Precautions ............................................... 5
Using this Menu ....................................................................... 6
Introduction ................................................................................ 10
System Requirements............................................................. 10
Main Features ........................................................................ 10
Package Contents .................................................................. 11
Camera Views ........................................................................ 12
Camera Buttons ..................................................................... 14
Navigation Control ................................................................. 15
Getting Started ............................................................................ 17
Inserting the Battery .............................................................. 17
Camera Memory .................................................................... 18
Inserting an SD/SDHC/SDXC Memory Card .............................. 19
Charging the Battery by USB .................................................. 20
Turning the Power On and Off ................................................ 20
Initial Settings ....................................................................... 21
Modes ................................................................................... 21
Using the LCD monitor ................................................................. 22
LCD Monitor Layout ............................................................... 22
Recording Images and Videos ...................................................... 27
Taking Images ....................................................................... 27
Setting the Zoom Control........................................................ 27
Using the AE/AF LOCK/UP Button............................................ 28
Using Flash............................................................................ 29
7
Setting the Focus Mode .......................................................... 30
Setting Continuous Shooting ................................................... 31
Using the Function Menu/Delete Button .................................. 32
Using the Movie Menu ............................................................ 37
Recording Videos ................................................................... 41
Using the Record Menu .......................................................... 51
Playback ..................................................................................... 59
Viewing in Single Navigation ................................................... 59
Viewing Thumbnails ............................................................... 59
Magnify ................................................................................. 60
Playing Videos ....................................................................... 61
Playing Voice Memo ............................................................... 62
Playback Menu....................................................................... 63
Using the Setup Menu .................................................................. 74
Setting Sounds ...................................................................... 74
Setting Power Save ................................................................ 75
Setting Date & Time............................................................... 75
Setting Language ................................................................... 76
Setting Display Mode.............................................................. 76
Setting TV Out ....................................................................... 76
Setting LCD Brightness ........................................................... 77
Setting Format ....................................................................... 77
Reset All ................................................................................ 77
Making Connections ..................................................................... 78
Connecting the Camera to a TV .............................................. 78
Connecting the Camera to a PC .............................................. 78
Connecting the Camera to a Printer ........................................ 79
Setting the Print Mode Menu .................................................. 80
Appendix..................................................................................... 81
8
About Folder and File Names .................................................. 81
Troubleshooting ........................................................................... 81
Specifications .............................................................................. 83
9
Introduction
Congratulations on your purchase of the new digital camera.
Capturing high-quality digital images is fast and easy with this state-of-the-art
smart camera.
System Requirements
In order to get the most out of your camera, your computer must meet the
following system requirements:
For Windows:
• Windows XP/Vista/Win7/Win8
• Processor: Intel Pentium D 3.0GHz or equivalent AMD Athlon, or faster
• Memory: 2 GB or above
• HDD space: 300MB or above
• 32bit color display monitor
• Microsoft DirectX 9.0C
• USB port and CD-ROM drive
For Macintosh:
• Mac OS 10.3.9 ~ 10.8 <Digital Camera>
• Memory: 1 GB or above
• Q. Time player ver. 6.0.3 or above
• USB port and CD-ROM drive
Main Features
• 20 mega pixels resolution
• Up to 5x optical zoom and 8x digital zoom
• 2.7 inch color LCD monitor
• 64MB internal flash memory with optional external SD/SDHC/SDXC card
• Supports up to 4GB of SD card, and up to 32GB of SDHC card and to 64GB
of SDXC card
• Easy-to-use button interface
• DCF, DPOF, PictBridge compatibility
• Slide show enables you to playback photos, videos and corrupted files
• A/V output to view your images and videos on your TV
• USB port to transfer images and videos to your PC
10
Package Contents
Please check the contents of your camera package. It should contain:
Digital camera
Rechargeable battery
x 1 pcs
USB cable
Wrist strap
CD-Rom
Quick Start Guide
11
Camera Views
Front View
1.
2.
3.
4.
Flash
Self-timer LED
Lens
Microphone
Back View
5.
6.
7.
8.
9.
10.
LCD monitor
LED indicator
Zoom button
Menu button
Movie button
OK
button/4-way
navigation
control
11. Playback button
12. Fn/Delete
button
12
Top View
13. Power button
14. Shutter button
Bottom View
15. Battery/
Memory card
compartment
16. Speaker
17. Tripod screw
hole
13
Left/Right View
18. USB/TV Out
19. Strap ring
Camera Buttons
Your camera is equipped with different buttons for ease of use.
Button
Description
Power
Press the Power button to turn the power on/off.
Shutter
Press to capture an image.
Zoom
button
Menu
Fn/Delete
In photo and movie mode, press the Zoom button (left/right) to
zoom out/zoom in.
In Playback mode, press button to zoom in to magnify image or
zoom out enter 9-image/calendar thumbnails.
Press to enter or exit menu/submenu.
In Photo mode, press to enter function menu.
In Playback mode, press to delete an image or video clip.
Playback
Press to enable Playback mode or return Record mode.
Movie
Press to start/stop recording video.
14
Navigation Control
The 4-way Navigation Control and the OK button allow you to access the
various menus available from the On Screen Display (OSD). You can configure a
wide range of settings to ensure maximum results from your images and videos.
Further functions of these buttons are as follows:
No.
Description
1
AE/AF LOCK
2
Macro Button
3
Flash Button
4
Continuous Shooting Button
5
OK Button
Button
Description
1.
2.
AE/AF
LOCK/Up
3.
To lock AE/AF, press the AE/AF LOCK/Up button in Program
Mode or half press the shutter button and then press the
AE/AF LOCK/Up button.
To unlock AE/AF by any one of the following ways:
•
Press the AE/AF LOCK/Up button
•
Press the Zoom button
•
Press the MENU/Fn/Playback/Movie/Power button to
launch another function
•
Switch to Super Macro/Manual Focus (For unlocking AE
only)
In Menu, press to navigate through the menu and submenu
selections.
15
1. In Photo Mode, press to scroll through Macro options. (Auto
Focus, Super Macro, Pan Focus, Infinity and Manual Focus)
Macro/Left
2. In Playback mode, press to view the previous image, video
or audio clip.
3. In Playback movie mode, press to rewind video playback.
4. In Menu, press to exit a submenu or to navigate through the
menu selections.
Flash/Down
1. In Photo Mode, press to scroll through the flash mode
options.
(Auto, Red-eye Reduction, Forced On, Slow Sync and Forced
Off)
2. In Menu, press to navigate through the menu and submenu
selections.
1. Press to scroll through Continuous Shooting options. (Single
shot, Burst, Speedy Burst and GIF Capture)
2. In Playback mode, press to view the next image or video.
Continuous
Shooting/Right 3. In playback Movie mode, press to forward video playback.
4. In Menu, press to enter the submenu or to navigate through
the menu selections.
1.
OK
Confirm a selection when using the OSD menus.
2. In Playback Movie/Audio mode, press to start video or audio
playback.
16
Getting Started
Inserting the Battery
Follow these instructions to insert the rechargeable battery into the
battery/memory card compartment.
Please read "Battery Information" on page 5 before inserting/removing
batteries.
1. Make sure the power is off before
inserting the battery.
2. Unlock and open the
battery/memory card
compartment at the bottom of the
camera.
3. Insert the batteries into the
compartment with the terminal
facing inside the camera with
correct orientation as shown.
17
4. Close and lock the battery/memory card compartment. In order to prevent
the battery from dropping, please make sure the compartment is locked
firmly.
Camera Memory
Internal memory
Your camera is equipped with 64 MB of internal memory. Users can store files
up to approximately 25 MB. If there is no memory card inserted in the memory
card slot, all images and videos recorded are automatically stored in the internal
memory.
External storage
Your camera supports SD cards of up to 4 GB in size. It also supports SDHC
cards with a maximum capacity of 32 GB. Then also supports SDXC cards with a
maximum capacity of 64 GB. If there is a storage card inserted in the memory
slot, the camera automatically saves all images and videos in the external
storage card. The icon
indicates the camera is using the SD card.
Not all cards will be compatible with your camera. When purchasing a
card, please check the card's specifications and take the camera with
you.
18
Inserting an SD/SDHC/SDXC Memory Card
Expand your camera’s storage by using
SD, SDHC or SDXC memory cards.
1. Unlock and open the Battery/memory
card compartment at the bottom of
the camera.
2. Insert the SD/SDHC/SDXC card into
the memory card slot with the metallic
part facing the back side of the
camera.
3. Push the SD/SDHC/SDXC card into the
memory slot until it clicks into place.
4. Close and lock the Battery/memory
card compartment.
To remove the SD/SDHC/SDXC card
5. Unlock and open the battery/memory
card compartment.
6. Gently push the card until it pops out.
7. Pull out the card carefully.
•
Windows 2000/XP does not support SDXC card (exFAT format).
But in Windows XP (Service Pack 2 or 3), you can download exFAT
patch update to support SDXC card.
•
To use the SDXC card with Mac OS, the OS version should be 10.5
or higher.
•
The memory card that is not inserted correctly may cause damage
to the camera. Please be careful when inserting the memory card.
•
To prevent children from swallowing the memory card, please
keep the memory card out of reach of children.
19
Charging the Battery by USB
You can also charge the battery by connecting the USB cable to your camera
and PC.
1. Connect the camera with the USB
cable as shown.
2. Connect the other end with the
USB adapter and plug it into a
power outlet or into the PCs USB
port.
• When the battery is charging,
the LED indicator flashes.
• When the battery is fully
charged, the LED indicator
goes off.
• When the battery is unusually
charged, the LED indicator
flashes rapidly.
• When the camera charges
without the battery inside, the
LED indicator goes off.
•
It's recommended to not operate the camera when charging.
Charging time depends on current battery capacity and charging
conditions.
•
You can also charge the battery with an Apple adapter. Its power
output meets the standard 5V/500mA.
•
If the battery is removed during charging, it will only recover after
you unplug or replug the USB cable.
Turning the Power On and Off
There are two ways to turn on the camera:
• The startup image displays briefly and the startup sound plays if enabled. The
zoom lens extends and the camera is turned on in Record mode.
• The camera is turned on in Playback mode. The zoom lens is not extended.
To turn off the camera, press the Power button.
See "Modes" on page 21 to know more about Record and Playback mode.
20
Initial Settings
When you turn on your camera for the first time, you will be asked to do the initial
settings of your camera. First is the setup of the language menu. Specify which
language you would like the menus and messages to be displayed in on the LCD
monitor.
Setting the Language
1. Press
,
,
or
to move through the selection.
2. Select a language, and then press OK to apply.
Setting the Date & Time
1. Press
or
to move through the selection.
2. Press
or
keys to change the value for the date and time.
3. Press OK to apply.
4. If necessary, press
to Cancel and return to language.
Now, you are ready to start taking images and videos.
Holding down
or
keys to change the values continuously.
Modes
Your camera has three modes:
Record Mode
Default mode when you turn on your camera. You are able to take images in
this mode.
Playback mode
Press the Playback button
after the camera is turned on to view and
edit captured images or playback videos. The recording of voice memos
attached to images is available in this mode.
Movie mode
Press the Movie button
after the camera is turned on to start/stop
recording video in this mode.
21
Using the LCD monitor
The LCD monitor shows all important information regarding camera settings as
well as the visual image of your image or video. The display on the LCD monitor
is called the On Screen Display or OSD.
LCD Monitor Layout
Photo Mode Screen Layout
No.
Item
Description
1
Record Mode
Indicates the current mode.
2
Flash
Indicates flash settings.
3
Self-timer
Indicates self-timer settings.
4
Zoom indicator
Displays zoom.
5
Shots
remaining
Indicates the remaining shots available.
6
Battery
Indicates battery level.
7
Storage media
Indicates current storage media in use.
8
Wind Cut
Reduces wind noise during movie recording.
9
Movie size
Indicates movie size.
10
Date stamp
Indicates date stamp is enabled.
22
11
Shake warning
Indicates the light is not enough and the camera is
shaking, which may cause the captured image to blur.
If the shake warning appears, you can still capture
images. However, enable Stabilizer, flashlight or use
of a tripod is recommended to stabilize the camera.
12
Stabilizer
Indicates stabilizer function is enabled.
13
Histogram
Graphic display of Brightness.
14
ISO
Displays ISO settings.
15
Shutter speed
Displays shutter speed settings.
16
Aperture value
Displays aperture settings.
17
Focus area
Indicates focus area.
18
AE/AF Lock
Indicates AE/AF Lock is enabled.
19
EV
Compensation
Displays exposure compensation settings.
20
Focus mode
Indicates focus is enabled.
21
White balance
Displays white balance settings.
22
Face tracking
Indicates face tracking is enabled.
23
Tracking AF
Indicates tracking AF is enabled.
24
Metering
Displays metering settings.
25
Quality
Displays quality settings.
26
Photo size
Displays photo size settings.
27
AF lamp
Indicates AF lamp is enabled.
28
Exposure
bracketing
Displays Exposure bracketing settings.
29
Stylish
Indicates Stylish function is enabled.
23
Movie Mode Screen Layout
Recording Layout
No.
Item
Description
1
PIV available
Indicates that you can capture a screenshot without
stopping movie recording.
2
Recording
status
Indicates recording status.
3
Recorded
time
Displays recorded time.
4
Key indicator
Displays the commands on 4-way Navigation Control
button.
24
Playback Mode Screen Layout
The Playback mode display varies depending on the type of image being
viewed.
Playback mode display of still images:
No.
Item
Description
1
Playback
mode
Indicates playback mode.
2
Protect
Indicates file is protected.
3
Voice memo
Indicates voice memo is attached.
4
Button intro
Indicates the button to press on the camera to play a
video file.
5
File
Indicates the file number over the total number of files in
no./Total no. the storage card.
6
Battery
Indicates battery level.
7
Storage
media
Indicates used storage memory.
8
Recording
information
Displays recording information of the file.
9
DPOF
Indicates the file is marked for printing.
10
Image Size
Displays the image size settings.
25
Playback mode of videos:
No.
Item
Description
1
Playback mode
Indicates playback mode.
2
Protect
Indicates file is protected.
3
Video clip
Indicates the file is a video.
4
Button indicator
Displays the button info of Playback mode.
5
File no./Total no.
Indicates the file number over the total number of
files in the storage card.
6
Battery
Indicates battery level.
7
Storage media
Indicates used storage memory.
8
Recording date &
Displays the date and time of the video clip.
time
9
Video size
Indicates the size of the video clip.
10
Button intro
Indicates the button to press on the camera to adjust
the volume.
11
Video length
Display the total length of the video clip.
12
Video time
Indicates the video time.
13
Playing status
Displays playing status.
14
Button intro
Indicates the button to press on the camera to play a
video file.
26
Recording Images and Videos
Taking Images
Now that you are familiar with your camera, you are ready to take your images.
Taking images with your camera is very simple.
1. Turn on the camera by pressing the Power
button.
2. Frame the shot using the focus bracket on
the LCD monitor. See illustration on the right.
3. Pressing the Shutter button down halfway
automatically focuses and adjusts the
exposure, and pressing the Shutter button
down fully captures the images.
When the shake warning icon
appears, hold
the camera steady, use a tripod to stabilize the
camera if needed.
Setting the Zoom Control
Using a combination of 5 times optical zoom and 8 times digital zoom permits
zoom photography up to 40 times magnification. While the digital zoom can be a
useful feature, the more an image is enlarged (zoomed), the more pixelated
(grainier) the image will appear. Please refer to "Setting the Digital Zoom" on
page 56 on how to setup digital zoom.
To adjust the optical zoom:
1.
Press the Zoom button to zoom in or zoom out of an image.
2.
The zoom indicator appears on the LCD monitor.
Zoom button
1. Press the Zoom button (right) to zoom
in.
2. Press the Zoom button (left) to zoom
out.
27
To adjust the digital zoom:
1. Activate digital zoom. See "Setting the Digital Zoom" on page 56.
2. Press the Zoom button (left/right) optically zooms in/out to the maximum
until it stops.
3. Release the Zoom button.
5x optical zoom
8x digital zoom
Using the AE/AF LOCK/UP Button
Use the AE/AF LOCK/UP button on your camera to lock
focus and exposure.
AE/AF LOCK/UP
Button
1. To lock AE/AF, press the AE/AF LOCK/Up button in
Program Mode or half press the shutter button and
then press the AE/AF LOCK/Up button.
2. To unlock AE/AF by any one of the following ways:
• Press the AE/AF LOCK/UP button
• Press the Zoom button
• Press the MENU/Fn/Playback/Movie/Power button to launch another
function
• Switch to Super Macro/Manual Focus (For unlocking AE only)
28
Using Flash
When taking pictures in difficult lighting conditions, use the Flash/Down
button to get correct exposure. This function cannot be activated when
recording videos or continuous shooting.
To activate Flash:
• Press the Flash/Down button on your camera
repeatedly until your desired flash mode is
displayed on the LCD monitor.
Flash/Down
button
Your camera is equipped with five flash modes:
Auto Flash. The flash fires automatically
whenever extra lighting is needed.
Red-eye reduction. The flash fires twice
to reduce the red-eye effect.
Forced on. The flash fires whenever you
press the Shutter button regardless of lighting
conditions.
Slow sync. The flash fires with a slow
shutter speed.
Forced off. The flash is turned off.
•
Flash function is only available when shooting still images but not
available in Burst and GIF modes.
•
Do not press the flash while pressing the Zoom button. Press the
flash after releasing the Zoom button if necessary.
29
Setting the Focus Mode
This function allows users to define the type of focus when recording a still
image.
To set the Focus mode
• Press the Focus/Left button on your camera to launch the Focus function.
• To select focus options, press the
save and apply changes.
or
Focus/Left button
Your camera supports the 4 focus modes:
Auto Focus. With auto focus, the camera
will focus on the subject automatically.
Macro/Super Macro. This mode is
designed for close-up photography. When
Super Macro is set, the focus cannot be
adjusted until Super Macro is cancelled.
Infinity. When Infinity is set, the camera
focuses on distant objects.
Manual Focus. With manual focus, you
can adjust the focus distance from 5cm to
infinity by press Up/Down button. Press OK
button to lock the focus and exit the adjusting
screen.
30
keys. Press the OK button to
Setting Continuous Shooting
This function allows users to set the
continuous shooting mode. It's only
available in shooting still images. Press
Right button to launch the Continuous
Shooting menu options, and then press
Left/Right button to select the desired
option.
Continuous Shooting/Right
button
Icon
Item
Description
Single Shot
Disable the continuous shooting function.
Burst
Fully press and hold the shutter button for continuous
shooting. It will only stop when you release the shutter
button or the memory card is full.
Speedy
Burst
Captures 30 images in a shot when the Shutter button is
pressed.
Auto set Image size to 4:3 VGA only.
Use this feature to take a specific number of images in a
specific shooting interval. The taken images will be
GIF Capture
combined into a GIF file and will no longer exist
individually.
31
Using the Function Menu/Delete Button
Function Menu
Press the Fn/Delete button in Record mode to bring up the Function Menu
with the most common features for photos and movies.
Press the Fn/Delete button of your camera to launch the Function Menu.
Press the Fn/Delete button again to close the menu.
Menu Options
•
The Menu bar displays the
Menu
current status of your camera
bar
settings. Only the available
functions for the settings are
shown as icons on the menu bar.
•
The available options for each
item on the menu bar are shown
in the Menu options.
•
Use the
or
key to move
through the menu selections
then press the OK button to
save and apply changes.
•
Press Menu button or
Fn/Delete button to cancel
selection and close Function
Menu.
32
Photo Size
The Photo Size function is used to set the
resolution before you capture the image.
Changing the Photo Size affects the number of
images that can be stored in your memory
card. The higher the resolution, the more
memory space is required.
The table below shows the Photo Size values for still images.
Icon
Pixel Size
Printing Size
Suggestion
Icon
Pixel Size
Printing Size
Suggestion
5152 x
3864
A2 Size
5152 x
3435
Standard print
paper
3264 x
2448
A3 Size
5152 x
2898
HDTV
2592 x
1944
A4 Size
1920 x
1080
HDTV
2048 x
1536
4" x 6"
2992 x
2992
Square
Composition
640 x 480 E-mail
33
EV Compensation
Images can be captured with the overall scene
intentionally made brighter or darker. These
settings are used when a suitable brightness
(exposure) cannot otherwise be obtained in
circumstances where the difference in
brightness between the subject and the
background (the contrast) is large, or when the
subject that you wish to capture is very small
within the scene. Available for still images only.
•
To adjust EV settings, press the
or
keys to increase/decrease the value. As
you adjust the settings, the LCD monitor
synchronously displays the image
applying the EV settings. Press the OK
button to save and apply changes.
•
The EV compensation is enabled only when using Program mode.
•
The EV menu is hidden if the Tracking AF has been turned on.
ISO
This sets the sensitivity for capturing images.
When the sensitivity is raised (and the ISO
figure is increased), photography will become
possible even in dark locations, but the image
will appear more pixelated (grainier).
• Use a higher ISO setting in dim conditions
and a lower ISO setting in brighter
conditions.
34
Metering
This sets the metering method for calculating
the exposure.
Icon
Item
Description
Multi
The entire area of the screen is measured, and the
exposure is calculated.
Center
Averages the light metered from the entire frame, but
gives greater weight to the subject matter at the center.
Spot
A very small portion of the center of the screen is
measured, and the exposure is calculated.
AF Area
AF stands for Automatic Focus. This feature
determines the area on which the camera
focuses.
To set AF Area
1. From the Record menu, select AF Area.
2. Use the
or
selection.
keys to go through the
3. Press the OK button to save and apply
changes.
The table below shows the available AF area settings.
Icon
Item
Description
Face Tracking
This feature auto detects faces and tracks
continuously.
Wide
The camera automatically selects focus area within
the wide frame.
Center
The focus area is fixed on the center.
35
Tracking AF
The camera will focus the subject as it moves and
keep it continually in focus automatically.
AE-L/AF-L
This feature allows locking exposure or focus
or both of them by pressing AE/AF LOCK/UP
button. You can define the AE/AF LOCK/UP
button to be one of the following functions:
•
AE-L: Lock/Unlock exposure.
•
AF-L: Lock/Unlock focus.
•
AE-L & AF-L: Lock/Unlock both exposure
and focus.
Press the AE/AF LOCK/UP button to unlock it.
Self-timer
Your camera features a Self-timer which can
be set in the Self-timer function in the
Function Menu. The Self-timer allows you to
take images after a pre-defined delay, while
burst lets you take consecutive shots. This
function is only available when recording still
images. The Self-timer setting is automatically
set to off when you turn off the camera.
To set the Self-timer
1. From the Function menu, select
Self-timer.
2. Use the
selection.
or
keys to go through the
3. Press the OK button to save and apply
changes.
The table below shows the available Self-timer settings.
Icon
Item
Description
Off
Captures an image without time delay.
10 Sec.
Sets a 10-second delay to capture image after pressing
the Shutter button.
36
2 Sec.
Sets a 2-second delay to capture image after pressing
the Shutter button.
Double
Performs delay and captures twice:
•
Performs a 10-second delay, then captures the
image.
•
Performs another 2-second delay then captures the
image again.
Using the Movie Menu
You can access the Movie menu simply by pressing the MENU button on your
camera.
When the menu is displayed, use the 4-way navigation control and the OK button
to move through menu selections and apply your desired settings. To close the
menu anytime, press the menu button again.
Setting Movie Mode
Use this function to adjust the resolution and
quality of movie clips.
•
The options FHD and HD are only available when a SDHC class 4 or
class 6 card is inserted.
•
Due to limits from the FAT format, VGA recording requires
approximately 2 hours.
Setting Prerecord
You can catch the first three seconds of action
you would have potentially missed. Once this
function is enabled, the camera starts recording
video automatically before pressing Movie
button. As soon as the Movie button is hit, the
most recent three seconds of video is added to
the beginning of the clip.
The icon is displayed in red when Prerecord is
on.
37
Prerecord will be canceled in the following situation:
•
After recording starts.
•
Switch to Playback mode.
•
Launch the Menu.
•
Enter USB mode.
•
Power off the camera.
Prerecord function will be disabled in the following situations:
•
The prerecord time is less than 2 seconds.
•
There is not enough internal memory to enable this function unless
an additional memory card is inserted to the camera.
Wind Cut Setting
This feature reduces wind noise during movie
recording.
Continuous AF
This function allows you to record video with auto
focus method.
1. Enable the Continuous AF under the Movie
Menu.
2. Use the
or
selection.
keys to go through the
3. Press the OK button to save and apply
changes.
38
Delete Button
The Delete function allows you to remove unwanted files in the internal memory
or on the memory card. Protected files cannot be erased, to delete, unprotect
the file first. See "Protect" on page 64.
To delete an image/video clip:
1. Press the Playback button
on the camera.
2. View images/videos clips in Single navigation mode.
3. Use the
or
keys to scroll the display.
4. When the desired image/video clip is displayed on the LCD monitor, press
the Delete button.
5. A confirmation selection appears on screen.
6. To close the Delete function and go back to the single navigation mode,
press Menu button.
To delete a single file:
1.
After a confirmation selection appears on
screen. Select Single.
2.
Press the OK button and select Yes to
delete.
3.
The next image is displayed on the LCD
monitor. To delete another file, use the
or
keys to scroll through the
images/videos clip. Repeat steps 1 to 2.
4.
To close the Delete function and go back
to the single navigation mode, press
Menu button.
To delete attached voice memo:
1. After a confirmation selection appears on
screen. Select Single.
2. A delete voice memo option will be added
to the selection.
3. Select and press OK to delete voice memo
only and back to single navigation.
4. Or select Yes to delete both image and its
voice memo.
39
To delete multiple files:
1.
After a confirmation selection appears on
screen. Select Multi.
2. The images are displayed in thumbnail
view on the LCD monitor.
3. Use the
the files.
or
keys to move through
4. When the desired image/video clip is
highlighted, use the
or
keys to
mark/unmark image/video clip for
deletion.
5. Repeat step 4 until all desired images
which you would like to delete are
marked.
6. Press the OK button. A confirmation
selection appears.
7. Select Yes to confirm.
8. Press the OK button to delete marked
files.
To delete all files:
1. After a confirmation selection appears on
screen. Select All.
2. Select Yes.
3. Press the OK button to delete all files.
40
Recording Videos
You can record videos with this camera, the
available recording time depends on the
capacity of the memory card. Videos can be
recorded until the maximum memory capacity
has been reached. However the length of a
single video may be limited (the limitation
depends on the camera model).
1. Press the Movie button to start
recording.
2. Focus your camera on the subject that you want to take.
3. Use the Zoom button to zoom in and zoom out an image.
4. To stop recording, press the Movie button.
• The camera will automatically stop recording when the memory
capacity is full.
• It will automatically stop recording when the recording time is over
29 minutes or the file size is over 4 GB.
• When the temperature of CCD Sensor is over 63ºC, the camera will
display the warning message.
• When the temperature of CCD Sensor is over 65ºC, the camera will
shutdown automatically.
PIV function
During the movie recording, press shutter button, an icon
displayed on LCD
means that the current screen can be stored as a photo without stopping movie
recording by pressing the shutter button. The PIV feature is only applicable to
movie size: 720p30 and VGAp30.
• When the movie size is 720p (30fps), the captured photos are saved
at 1280 x 720 resolution.
• When the movie size is VGA (30fps), the captured photos are saved
at 640 x 480 resolution.
Settings of Recording Videos
See "Using the Movie Menu" on page 37 for more details.
41
Setting the Scene Mode
By simply selecting one of the following 23
modes, you can capture the image with the
most appropriate settings.
1. From the Record Menu, press to select
Scene Mode.
2. Use the navigation controls to move
through the selection.
3. Press the OK button to save and activate
the selected scene mode.
The table below shows the available scene mode settings.
Icon
Item
Description
Intelligent
Scene
The camera detects the shooting conditions and
automatically switches to the appropriate scene
mode. See "Using Intelligent Scene" on page 44 for
more details.
Program
The camera automatically adjusts suitable shooting
settings like shutter speed and aperture values.
Portrait
The camera blurs the background to focus on the
subject.
Landscape
This feature is used to emphasize wide scenic views.
Sunset
This feature enhances the red hue for recording
sunset images.
Backlight
This feature is used to capture the image of a
backlight object by changing the metering.
Kids
This feature is used to capture still images of moving
kids.
Night Scene
This feature is used to capture images with night
scenery background.
Fireworks
This feature slows shutter speed to capture fireworks
explosions.
Snow
This feature is used for beach and snow scenes.
Sports
This feature captures still images in high speed
motions.
42
Party
This feature is used for wedding or indoor party
settings.
Candlelight
This feature is used to capture warm candle light
effects.
Night
Portrait
This feature is used to capture portrait pictures with
night or dark backgrounds.
Soft Skin
This feature enhances skin tone thus facial skin
appears smooth.
Flowing
Water
This feature enhances smooth effects like water or
silk.
Food
This feature is used to capture food images. The
increased saturation in this mode makes the captured
image more enticing.
Love Portrait
This feature uses face tracking to auto detect faces to
capture portraits images without the help of others.
When over two faces are detected, AF is automatically
activated. The camera starts count down and
captures a picture in two seconds.
Self Portrait
This feature sets zoom to wide. When one face is
detected, AF automatically activated and plays the
sound (Bi) for notice. Then camera starts count down
and captures a picture in two seconds.
D-Lighting
This feature applies digital processing only to the
necessary portion(s) of the image and preserves
details in highlights and shadows with natural
contrast.
Time Lapse
Use this feature to take photos automatically at the
specified intervals. See "
Using Time Lapse" on page 46 for more details.
Panorama
Use this feature to create a panoramic photo by
panning or tilting the camera.
Art Effect
This feature applies different art effect on the still
images.
43
Using Intelligent Scene
This feature is most useful for novice users to capture great images even
without basic knowledge of photography. Simply frame the shot with the help of
Intelligent Scene Mode, the camera automatically recognizes 7 kinds of scenes Portrait, Landscape, Macro, Backlight, Backlight Portrait, Night Scene and Night
Portrait - and selects the ideal settings.
Intelligent scene icon. After the camera detects the
shooting conditions, this icon changes to show the
detected scene mode.
The camera changed to
Landscape mode automatically.
To activate Intelligent Scene
1. Select Intelligent Scene
Scene Mode menu.
in
2. Focus the camera on the subject to
capture.
3. The camera detects the shooting
conditions and switches to an
appropriate scene mode.
4. Half press the Shutter button to
focus the subject. The frame turns
green to indicate focus is set.
5. Press the Shutter button to take
the shot.
44
Using Kids Mode
Tactically, kids are the most difficult to
photograph. They tend to be highly animated
and can be a real challenge to make them pay
attention for more than just a second or two.
To capture a great moment for your kids, just
keep the camera in kid mode. The mode
provides higher shutter speed and always
focuses on moving subject.
Using Sports Mode
When you need a series of sports motion images, such as a golf swing, or try to
capture the images of a flying hummingbird/butterfly, be sure to switch the
scene mode to sports mode.
Using Party Mode
Leave Party mode on! It can be difficult to get a photograph of everyone at a
party. While you have the whole gang together, take a group or family portrait.
Party mode features Red-eye reduction flash and face tracking. You’ll miss fewer
shots, and have more time to focus on enjoying the party.
Using Food Mode
Share your dining experiences online with Food
mode. This mode features on macro focus and
auto flash designed for close-up photography.
Macro focus and Auto
Flash are enabled by using
Food mode.
Using Love Portrait
Want to take a good image when there are just two of you? All you have to do is
hold the camera and smile.
If two faces have been recognized, the camera performs a 2-second countdown
and then takes a photograph without you having to press the Shutter button.
45
Using Self Portrait
When you are taking a photograph of yourself select self portrait mode. First the
camera begins face tracking. If a face had been recognized, the camera
performs a 2-second countdown and then takes a photograph without you
having to press the Shutter button.
Using Time Lapse
Use this feature to take photos automatically
at the specified intervals. The photo size will
be 16:9 (2M). In Time Lapse mode, press
Right button to launch the Time Lapse
menu, and then press Up/Down button to
select the options.
Available options are 30 sec. (Default), 1
min., 5 min., 10 min., 30 min., 60 min. Press
OK button to apply the setting and close the
menu.
And
You can fully press the Shutter button to start
and stop recording. The Time Lapse photos
will be merged into a Time Lapse movie at 10
fps.
Photos taken from Time Lapse will be combined into a movie and will
NOT exist individually in photo.
46
Using Panorama Mode
Use this feature to create a panoramic photo
from multiple shots. You can combine several
shots into one single image quickly and easily.
• The actual size of the image may differ from time to time.
• It is recommended to use a tripod to stabilize the camera, and then
move the camera slowly during capturing.
• A time limit of 30 seconds is given to capture the photgraph.
• If you select From Top to Bottom or From Bottom to Top in
360-degree panorama, it is recommended to turn the camera over
90 degrees in order to make sure the camera is stable.
• In Panorama mode, uneven brightness may result in the photograph
looking slightly different than what you expected.
To stitch the still image
1. Press
key to launch the Angle
Menu. Use the
or
keys to
select options. Press the OK button
to save and apply changes.
47
2. Press
key to launch the
Direction Menu. Use the
or
keys to select options. Press
the OK button to save and apply
changes.
3. Fully press the shutter button to
start shooting. When shooting starts,
a white-cross appears in the center
and a yellow line displays horizontally
(or vertically) through the screen. In
addition, a shooting bar is displayed
to show the shooting position and
the white bar indicates which part of
the scene has been taken.
4. If you move the camera without
keeping it straight, the yellow line
will move with the moving scene.
5. When the white bar reaches the end the camera will finish automatically
and save the panorama image.
48
Using Art Effect
Effect that cannot be presented on Preview.
Does not apply to movie recording and
continuous shooting.
Press
or
Icon
keys to select between the following settings:
Item
Description
Stylish
This feature is used to capture images with
over-saturated colours, off-kilter exposure or
blurring.
Soft Focus
Produces halo around the photographed object to
achieve the effect of soft focus.
Light Tone
Reduces contrast to create a smooth and relaxed
atmosphere.
Vivid
The camera captures the image with more
contrast and saturation emphasizing on the bold
colours.
Miniature Effect
Blur parts of the photo to make the scene look like
a miniature scale model. It is recommended to
capture from a high angle to simulate the
miniature effect.
Fisheye Lens
This feature captures images with fisheye lens
effects.
Astral
Image is applied with starburst.
Poster
This feature captures images with old poster or
illustration effects.
Impressive Art
This feature captures images with dramatic
contrast.
49
B&W
Images are captured in black and white.
Sepia
Images are captured in sepia tones.
Color Accent (Red)
Retains red tone while the rest of the scene
becomes black and white.
Color Accent
(Orange)
Retains orange tone while the rest of the scene
becomes black and white.
Color Accent
(Yellow)
Retains yellow tone while the rest of the scene
becomes black and white.
Color Accent
(Green)
Retains green tone while the rest of the scene
becomes black and white.
Color Accent (Blue)
Retains blue tone while the rest of the scene
becomes black and white.
Color Accent
(Purple)
Retains purple tone while the rest of the scene
becomes black and white.
50
Using the Record Menu
If you are in Photo Mode, you can access the Record menu simply by pressing the
MENU button on your camera.
When the menu is displayed, use the 4-way navigation control and the OK button
to move through menu selections and apply your desired settings. To close the
menu anytime, press the menu button again.
Record Menu
The Record menu allows you to change modes,
and setup other capture settings.
To go to Record Menu:
Turn on the camera by pressing Power button.
Press
to launch the Record Menu.
Use the
or
keys to move through the menu
To select an item, press
or OK button.
Change the submenu settings using the 4-way
navigation control.
Press the OK button to save and apply settings.
51
The table below shows the Photo Size values for still images.
Icon
Pixel Size
Printing Size
Suggestion
Icon
Pixel Size
Printing Size
Suggestion
5152 x
3864
A2 Size
5152 x
3435
Standard print
paper
3264 x
2448
A3 Size
5152 x
2898
HDTV
2592 x
1944
A4 Size
1920 x
1080
HDTV
2048 x
1536
4" x 6"
2992 x
2992
Square
Composition
640 x 480 E-mail
Quality
The Quality sets the quality (compression) at
which the image is captured. The quality
determines the amount of compression applied to
your images. Fine quality would give you the best
images with sharper details and less compression.
However, the higher the quality, the more memory
space is required in your memory card.
Icon
Item
Description
Superfine
5x compression rate.
Fine
8x compression rate.
Normal
12x compression rate.
52
White Balance
This sets the white balance for a variety of
lighting conditions.
•
As you move through the selection, you can
see the preview on the LCD monitor
synchronously.
•
Press
to enter WB Shift. This feature
allows you to correct the white balance of
AWB option.
Icon
Item
Description
Auto White Balance
The camera automatically
adjusts the white balance.
Daylight
Ideally used for bright sunny
conditions.
Cloudy
Ideally used for cloudy
conditions.
Tungsten
Ideally used for indoor images
with tungsten or halogen
lighting without a flash.
Fluorescent 1
Ideally used for indoor images
with bluish fluorescent lighting
conditions.
Fluorescent 2
Ideally used for indoor images
with reddish fluorescent
lighting conditions.
Used when light source cannot
be specified.
Press
for the camera to
automatically adjust the
appropriate white balance
setting according to the
environment.
Custom
53
ISO
This sets the sensitivity for capturing images.
When the sensitivity is raised (and the ISO
figure is increased), photography will become
possible even in dark locations, but the more
pixelated (grainier) the image will appear.
•
Use a higher ISO setting in dim conditions
and a lower ISO setting in brighter
conditions.
Maximum ISO Auto
This feature allows the camera to adjust the
ISO Auto from ISO 100 to the value set in
Maximum sensitivity, according to light
conditions. Available options are 200, 400,
800 (Default).
Metering
This sets the metering method for calculating
exposure.
Icon
Item
Description
Multi
The entire area of the screen is measured, and the
exposure is calculated.
Center
Averages the light metered from the entire frame, but
gives greater weight to the subject matter at the center.
Spot
A very small portion of the center of the screen is
measured, and the exposure is calculated.
54
Setting the Exposure Bracketing
Use this feature to take photos with different
exposure compensation. Bracketing records 3
continuous images in the following order:
Standard exposure, Underexposure and
Overexposure.
Available settings are: Off, ±0.3, ±0.7 and
±1.0.
Setting the AE-L/AF-L
This feature allows locking exposure or focus
or both by pressing the AE/AF LOCK button.
You can define the AE/AF LOCK button to be
one of the following functions:
•
AE-L: Lock/Unlock exposure.
•
AF-L: Lock/Unlock focus.
•
AE-L & AF-L: Lock/Unlock exposure and
focus.
Press the AE/AF LOCK button to unlock it.
To lock AE/AF, press the AE/AF LOCK button
during movie recording or half press the
shutter button then press the AE/AF LOCK
button in Photo mode.
Show this function only when using Program mode.
55
Setting the Digital Zoom
This feature controls the digital zoom mode of
your camera.
Your camera enlarges an image using the
optical zoom first. When the zoom scale
exceeds 5x, the camera uses digital zoom.
To set Digital Zoom
1. From the Record menu, select Digital
Zoom.
2. Use the
or
selection.
keys to go through the
3. Press the OK button to save and apply
changes.
The table below shows the available Digital
Zoom settings.
Icon
Item
Description
On
Enlarges all image sizes, but the image quality
deteriorates.
Off
Uses the optical zoom only.
Digital Zoom is not available when Face Tracking is on.
56
Setting the Date Stamp
The date of recording can be printed directly
on the still images. This function must be
activated before the image is captured. Once
date and time are stamped on an image, they
can no longer be edited or deleted.
Limitations of Date Stamp functions are as
follows:
• Available for still images only.
• This feature does not apply to continuous
shooting mode.
• In vertical or rotated images, the date and
time on your images still appear
horizontally.
To set Date Stamp
1. From the Record menu, select Date Stamp.
2. Use the
or
keys to go through the selection.
3. Press the OK button to save and apply changes.
Setting Auto Review
The Auto Review function lets you view the
captured image right after shooting it.
If Auto review is On, the camera will display
the captured image for 1 second on the LCD
monitor.
To set Auto Review
1. From the Record menu, select Auto
Review.
2. Use the
selection.
or
keys to go through the
3. Press the OK button to save and apply
changes.
Blink Detection
Nothing ruins a great picture more than having your subjects' eyes closed.
Blink Detection provides you with extra assurance when capturing
once-in-a-lifetime moments like holding a trophy with teammates after winning
a basketball game.
57
If closed eyes are detected, a saving confirmation menu appears on the screen,
allowing you to re-take the shot before your subject or subjects move on.
To activate Blink Detection
1. Enable Blink Detection from Record
menu.
2. Half press the Shutter button to focus
the subject. The frame turns green to
indicate focus is set.
3. Press the Shutter button to capture
the image and automatically save the
Image.
4. If the camera detects subject blinked eye, a "Save image" or "Cancel"
option appears on the screen.
5. Select Save image to save or Cancel to disregard
Blink Detection appears in Record menu only when Face Tracking is
turned on
Setting Grid Line
The Grid Line function will show a framing grid
on the preview of your photographs. Available
settings are: On, Off.
The configuration of Grid Line will be changed
with different aspect ratio.
Setting Stabilizer
This function allows you to prevent blurred
images caused by shaking.
1. Enable the Stabilizer under the Record
Menu.
2. Use the
selection.
or
keys to go through the
3. Press the OK button to save and apply
changes.
58
Playback
You can playback still images and video clips on the LCD monitor.
Viewing in Single Navigation
The Single navigation mode displays the image one by one on the LCD monitor. To
view images/video clips, follow the steps below.
1. Press the Playback button
on the camera.
2. The LCD monitor displays an image. To understand the icons and other
information on the screen, please see "Photo Mode Screen Layout" on page
22.
Still Image
3. Use the
or
Video
keys to view next/previous image/video.
4. To play a video clip, press the OK button. See "Playing Videos" on page 61 or
more details.
When playing videos under playback mode, lens will retract after 15
seconds, but the video playback will still continue.
Viewing Thumbnails
This function allows you to view 9 or 36 thumbnail images on the LCD monitor at
the same time. Searching numerous images is much easier than single view
navigation. To set 9-images or 36-images mode
1. Press the Playback button
on the camera.
2. Press the Zoom button (left) once to enter 9-images mode or twice to enter
36-images mode.
3. Use the navigation controls to move through the items.
4. Press the OK button to select the image and view it normally.
59
Scroll bar.
If scroll bars appear, it indicates that the screen
can be scrolled. It can be displayed 9 images
(3x3) or 36 images (6x6) at one time in
Thumbnail Screen. Use the 4-way navigation
control to select the file and press the OK
button to display the selected file in Single
Navigation.
Thumbnail 3x3
Thumbnail 6x6
Thumbnail icons:
When you view the thumbnails, some images may contain icons. These icons
indicate the type of file or recording.
Icon
Type
Description
File Error
Indicates an error file.
Video
Displays videos with roll film pattern.
Magnify
The zoom view function works with still images
only.
•
In normal view, press the Zoom button
(right) repeatedly until the desired zoom
view appears.
•
You can zoom to view an image of up to 12X.
•
Use the navigation controls to view the
zoomed image.
•
Press the Menu button from any
magnification ratio to return to Single
Navigation.
60
Playing Videos
1. Press the Playback button
camera.
on the
2. Use the navigation controls to scroll through
the saved images. A video clip has a video icon
displayed on screen.
3. Press the OK button to play the video.
4. During playback, press and hold the
or
keys to fast forward or rewind the video. The
camera supports forward and rewind speed of
up to 4x.
5. During playback, use the Zoom buttons to
control volume. Press the right button to
increase volume/Press the left button to
decrease volume.
6. Press the
key to pause playback. Press the
key
again to resume. When paused, the
play info will remain on screen except
.
7. To forward or rewind the video frame by
frame, press the key
to pause playback,
then press the
or
keys.
8. Press the
key to stop the playback. The
LCD monitor will display the video frame image
in Single navigation mode.
•
The playback info, except the icon
, will be displayed when
the video is paused, during REW/FF or frame by frame modes
•
Volume cannot be adjusted when paused or during REW/FF
modes.
61
Playing Voice Memo
Voice memo is separately recorded and attached to a captured image. See
"Voice Memo" on page 66 on how to record voice memo.
1. Press the Playback button
camera.
on the
2. Use the navigation controls to scroll through
the saved images. An image file with voice
memo has a voice memo icon located on the
top center of the LCD monitor. See picture
on the right.
3. Press the OK button to play the voice
recording.
4. During playback, use the Zoom buttons to
control volume. Press the right button to
increase volume/Press the left button to
decrease volume.
5. Press the key
to pause playback. Press
the key
again to resume. When paused,
the play info will remain on screen except
.
6. Press the key
to stop the playback. The
LCD monitor displays the image in Single
navigation mode.
Volume cannot be adjusted when you pause the voice memo.
62
Playback Menu
The Playback menu allows you to edit images, record voice memos, and setup
playback settings.
To go to Playback Menu:
1. Press the Playback button
camera.
on the
2. Press Menu button to launch the Playback
Menu.
3. Use the
or
keys to move through the
menu selections.
4. To select a menu, press
button.
or the OK
5. Change the submenu settings using the
4-way navigation control.
6. Press the OK button to save and apply
settings.
Slideshow
The slideshow function enables you to playback your photos, videos and error
files according to naming order.
To view Slideshow:
1. From the Playback menu, select Slideshow. The Slideshow menu appears.
2. Set the slideshow settings.
3. Select Start, then press the OK button to start the slideshow.
4. During Slide Show, press the UP button to pause slideshow.
5. Use the
or
keys to move through the options. Select whether to
Continue or Exit the slideshow.
6. Press the OK button to apply selected option.
To change slide show settings:
1. From the slideshow menu, use the
or
keys to move through the selections.
2. Select Interval setting. Press the
or
keys to adjust. Choose among the available
interval settings: 1 sec., 3 sec., 5 sec., and
10 sec.
3. Select Repeat setting. Press the
or
keys to adjust. Available settings are: Yes,
No.
63
Protect
Set the data to read-only to prevent images from being erased by mistake.
A protected file has a lock icon
when viewed on Playback mode.
To protect files:
1. From the Playback menu, select Protect.
2. The Protect submenu is displayed on the
LCD monitor.
Available select settings:
•
Single. Select one file to lock/unlock.
•
Multi. Select multiple files from the
thumbnail view to lock/unlock.
•
Lock all. Lock all files
•
Unlock all. Unlock all files.
To protect/unprotect a single file:
1. Select Single in the Protect submenu, the
images are displayed on the LCD monitor in
single navigation mode.
2. Use
or
keys to scroll the display.
3. When the desired file is displayed on the
LCD monitor, press the OK button to select
Lock/Unlock.
4. To close the protect/unprotect function and
go back to the Playback menu, select Exit.
To protect/unprotect multiple files:
1. Select Multi in the Protect submenu, the
images are displayed in thumbnail view on
the LCD monitor.
2. Use the
or
keys to move through the
files.
3. When the desired file is highlighted, use the
or
keys to mark/unmark the file for
protection.
4. Repeat step 3 until all desired files to protect
are marked.
5. Press the OK button to lock files and go
back to Playback menu.
64
To protect all files:
1. Select Lock all in the Protect submenu. A
confirmation message appears.
2. Select Yes.
3. Press the OK button to lock all files.
To unlock all files:
1. Select Unlock all in the Protect submenu. A
confirmation message appears.
2. Select Yes.
3. Press the OK button to unlock all protected
files.
65
Voice Memo
A maximum of 30 seconds of audio can be recorded as a memo for captured still
images.
To record voice memo:
1. Press the Playback button
2. Press the
or
on the camera.
keys to scroll and select an image to attach voice memo to.
3. Press the MENU button to launch the Playback menu.
4. Select Voice Memo.
5. Select Start, then press the OK button to start recording.
6. Press the OK button again to stop recording.
Time left (in seconds) for recording.
When you record a voice memo for an image with an existing voice memo, the old
recording file would be replaced by the new one.
Filter Effects
Filter Effects function is only applicable to aspect ratio 4:3 photos with different
artistic effect. Edited images in this function are saved as new files.
To activate Filter Effects:
1. Press the Playback button
camera.
on the
2. Press the
or
keys to scroll and select
an image to edit.
3. Press the MENU button to launch the
Playback menu.
4. Select Filter Effects. The Filter Effects
submenu appears.
5. Press the
or
keys to scroll and OK
button to select an option.
66
The succeeding table shows the available settings.
Item
Soft
Color
Emphasis
Description
Image is applied with soft effect.
Retains the color tone you choose while the rest of the scene
becomes black and white.
Vivid
Image is applied with more contrast and saturation emphasizing
the bold colors.
Miniature
Effect
Parts of the image will be blurred making the scene look like a
miniature scale model. It is recommended to apply to an image
that is captured from a high angle in order to help simulate the
miniature effect.
Astral
Impressive
Art
Image is applied with starburst.
Image is applied with dramatic contrast.
Painting
Image is applied with watercolor effect. Please note that if one
image is applied with Painting function already, it cannot be
applied with Astral again.
Negative
Image appears to be the opposite of the original image.
B&W
Image is applied with black and white.
Mosaic
Image is applied with mosaic tiles.
Sepia
Image is applied with sepia tones.
67
Trimming
The Trim function allows you to trim an image to another image size. This
function is only available for still images.
To trim an image:
1. Press the Playback button
on the
camera.
2. Press the
or
keys to scroll and
select an image to trim.
3. Press the MENU button to launch the
Playback menu.
4. Select Trimming. The Trim screen layout
is displayed on the LCD monitor.
5. Use the Zoom button to change the
trimming frame as zoom in/out.
No.
Description
1
Enlarged image
2
4-way indicator
3
Trimmed size
4
The approx. location of the trimmed
area
5
Image area
6. Use the navigation controls to move the image.
7. Press the OK button to apply changes. A menu selection appears.
8. Select whether to:
•
Yes. Save the new file as a new one.
•
Cancel. Cancel setting and go back to Playback Menu.
9. Press the OK button to save/cancel changes.
•
Trim function is not available for images with image size set to VGA.
•
All images will be trimmed in 4:3 ratio regardless of its original
image ratio.
68
Resize
Resizes a previously saved image to create a small copy photo. Only resizing to
a smaller size is available.
To resize an image:
1. Press the Playback button
camera.
on the
2. Use the
or
keys to scroll and select
an image to resize.
3. Press the MENU button to launch the
Playback menu.
4. Select Resize. The Resize submenu is
displayed on the LCD monitor.
5. Select size among: 640, 320, and 160.
6. After selecting size, a menu selection
appears.
7. Press the OK button to save/cancel
changes.
8. The resized image is saved as a new
photo.
•
Resize function is only applicable to aspect ratio 4:3 photos.
•
The original photos can be resized more than once. However, each
resized photo cannot be resized again.
Startup Image
You can specify the startup image from the captured images of the camera.
1. Press the MENU button to launch the
Playback menu.
2. Select Startup Image. The menu
selection appears.
3. Select options:
•
System. Use camera default image.
•
My Photo. Use the
or
keys to
scroll and select desired image.
•
Off. Disable the startup image.
4. Press the OK button to apply changes.
The startup image will still be displayed even if the selected image was
deleted.
69
DPOF
DPOF is the abbreviation for Digital Print Order Format, which allows you to
embed printing information on your memory card. You can select the images to
be printed and how many prints to make with the DPOF menu in the camera
and insert the memory card to the card compatible printer. When the printer
starts printing, it will read the embedded information on the memory card and
print the specified images.
To set DPOF:
1. Press the Playback button
camera.
on the
2. Press Menu button to launch the Playback
Menu.
3. Select DPOF. The submenu appears.
Available settings are as follows:
•
Select Images. Mark images in the
memory card.
•
Reset. Reset all DPOF settings to initial
default settings.
To set DPOF on images:
1. Select Select Images on the DPOF
submenu.
2. Use the
or
keys to scroll and select
images to mark for printing.
3. When the desired image is highlighted, use
the
or
to increase/decrease number.
4. Press the OK button to define the DPOF
settings and select Done to save DPOF
settings.
To reset DPOF:
1. Select Reset on the DPOF submenu.
2. The camera auto reset all DPOF settings.
70
Copy
Use this feature to copy images between internal memory and memory card.
To copy images between internal memory and
memory card:
1. Press the Playback button
camera.
on the
2. Press Menu button to launch the Playback
Menu.
3. Select Copy and choose a method you
want to copy images to. After choosing,
available settings are as follows:
•
Selected images. Select the chosen
images on the storage device
•
All images. Copy all selected images to
the storage device
To copy selected images:
1. Select Selected images on the Copy
submenu.
2. Use the
or
keys to scroll and select
images to mark for Copying.
3. When the desired image is highlighted, use
the
or
keys to mark/unmark the file
for copying.
4. Press the OK button and select Yes to start
copying.
To copy all images:
1. Select All images on the Copy submenu.
2. Select Yes to start copying.
If no memory card or a locked card is inserted, this option would be
grey.
71
Movie Paste
Use this feature to combine two videos with the same specification (movie size
and fps) into one video.
To combine two videos:
1. Press the Playback button
camera.
on the
2. Use the
or
keys to scroll and select
the original video.
3. Press the MENU button to launch the
Playback menu.
4. Select Movie Paste. The videos with the
same specification as the original video are
displayed on the LCD monitor.
5. Use the
or
keys to scroll and the
or
keys to mark/unmark the second
video.
6. Press the OK button and select Yes to
merge it to the end of the original video and
overwrite it.
•
The total length of the combined video cannot be over 30 minutes.
•
After combining videos, the second video will no longer exist as a
separate file.
72
Face Retouch
This function is only applicable to still images that were captured with Face
Tracking.
When you enter the Face Retouch menu, if the
photograph has over two faces locate the
cursor on the picture, if the photograph has one
face locate the cursor on the function at the
right side of the menu.
Only one face can be retouched at a time. All
functions will be reset to 0 when you exit from
the Face Retouch menu, no matter whether
you save the picture or cancel the setting.
Pictures that have been retouched will be saved
as a new image and this function can be applied
again.
Available
Settings
Item
Description
Smoothing
0-3
The Smoothing level is 0-3.
Brighten
0-3
The Brighten level is 0-3.
Enlarge Eyes 0-3
Save
N/A
The Enlarge Eyes level is 0-3.
Save the image.
73
Using the Setup Menu
You can access the Setup menu in Record or Playback mode.
The Setup menu allows you to configure general camera settings.
To go to Setup Menu:
1. Press Menu button to launch the
Record/Playback Menu.
2. Use the
or
keys to switch the menu
tab to Setup menu.
3. Use the
or
keys to move through
the menu selections.
4. To select an item, press the OK button or
key.
5. Change the submenu settings using the
4-way navigation control.
6. Press the OK button to save and apply
settings.
Setting Sounds
Use the Sound menu functions to control the sounds produced by the camera.
1. From the Setup menu, select Sounds.
2. Adjust sound settings.
3. Press the OK button to apply changes.
Item
Available Settings
Description
Sound 1, Sound 2,
Sound 3, Off
Selects the startup sound when camera
is turned on.
Shutter
On, Off
Enables or disables shutter sound when
Shutter button is pressed. Shutter sound
is not available when recording videos.
Beep
volume
0-4
Adjusts volume.
Startup
74
Setting Power Save
The Power Save function allows you to set an
idle time after which the camera automatically
goes into sleep mode to save power. After a
minute of being in sleep mode, the camera
eventually turns off power.
This function is not available in the following
instances:
•
Recording a video file
•
Playing a Slideshow/video file
•
Using the USB connector
•
AE/AF has been locked
•
During Movie Paste
•
During interval time on Time Lapse
Setting Date & Time
Use the Date & Time function to set the date and time of your camera. This
function is useful in attaching date stamps on captured images. Your camera
uses a 24-hour time format.
1. Press the navigation controls to adjust date
and time value. By holding down the
or
keys, the numeric values changes
continuously.
2. Press the OK button to apply changes.
75
Setting Language
Specify in which language menus and messages are to be displayed on the LCD
monitor.
1. Use the navigation control to scroll through
the list and select the desired language.
2. Press the OK button to confirm and apply
settings.
Setting Display Mode
This function controls the icon display on the
LCD monitor for both Record mode and
Playback mode.
Available settings are: On, Detailed Info, Off.
If you set Display Mode to Off, the mode icon
and remaining shots will display for 2 seconds in
the following situations:
•
Power on the camera
•
Switch from Playback to Record mode
•
After shooting
•
Close the menu and back to preview
Setting TV Out
Use the TV Out function to adjust video output signal to accommodate different
regional settings. If TV out is not set correctly, the image may not display
properly on the TV.
Available settings are:
•
NTSC. Applicable in Japan, USA, Canada,
Taiwan and others.
•
PAL. Applicable in Europe, Asia (excluding
Taiwan), Oceania and others.
76
Setting LCD Brightness
Select a brightness level for the LCD monitor.
Available settings are:
•
Auto. Auto detects the LCD brightness.
•
Bright. Enhance the LCD brightness.
•
Normal. Normal LCD brightness.
Setting Format
This utility formats current used memory
(Internal memory or Memory card) and erases
all stored images and data.
If a locked card has been inserted, the option would be grey.
Reset All
Use this function to reset the camera to its
factory settings. However, the following
settings are exceptions and are not affected by
Reset.
•
Date & Time
•
Language
•
TV Settings
•
Custom White Balance data
77
Making Connections
You can connect your camera to a: TV, computer, or a printer.
Connecting the Camera to a TV
You can play back your images on a TV screen. Before connecting to any video
devices, make sure you select NTSC/PAL to match the broadcast standard of the
video equipment you are going to connect to the camera.
To connect your camera to a TV:
1. Turn on the camera.
2. Set the TV to match the TV’s video out
format. See "Setting TV Out" on page 76.
3. Connect the USB/AV 2-in-1 cable to the
USB port on the bottom of your camera.
4. Connect the other end of the cable to the
TV’s AV input port.
5. The LCD monitor turns black and all
images and video clips are displayed on the
TV.
Connecting the Camera to a PC
You can transfer images and video files to
your PC.
1. Connect one end of the USB cable to
an available USB port on your
computer
2. Connect the other end of the USB
cable to the USB terminal on the
camera.
3. Turn on the camera.
4. The PC starts to detect the connection
while the LCD monitor appears
Connecting…
78
5. Connection established and the LCD monitor will be turned off.
6. Access the files in the camera by your PC.
•
The camera’s internal memory and memory card would display as
removable drives in Vista/Win7/Win8 PC.
•
When this camera is connected to your PC, two removable drives
will display. Please click AP link (Magix) in the second drive, and
then the Setup window will display (an Internet connection is
required). After installation, you can import / edit your photos,
movies and music. Please note that AP link (Magix) is the trial
version and will be used permanently after registration.
Connecting the Camera to a Printer
You can print your images directly using a PictBridge compatible printer.
1.
Turn on your Printer. Check that
the printer is turned on, there is
paper in the printer, and there are
no printer error messages.
2.
Connect one end of the USB cable
to the printer and the other end to
the USB terminal on the camera.
3.
Enter the print mode and print the
selected images.
For more details on "Setting the Print Mode Menu" go onto next page.
79
Setting the Print Mode Menu
Print Mode menu appears on the screen after the connection between a printer
and your camera is established.
Print Mode includes three major settings:
• Print Select. An image can then be
selected to print.
• Print All. Prints all images.
• Print DPOF. Prints the images which are
set DPOF.
To set Print Select
1. Use the
or
keys to scroll and select
an image for printing.
2. Specify the number of copies. Use the
or
key to increase/decrease number.
3. Press the OK button to enter printer
settings.
To set Print All and Print DPOF
Repeat the same steps 1 to 2, then enter printer
settings.
To set Printer Settings
1. Use the
or
key to specify a print
option.
2. Modify paper size, quality, date and info by
the
or
keys. Available setting:
• Paper size: Default / A4 / 4"x6"
• Quality: Default / Fine / Normal
• Capture Date: Yes / No
• Capture Info: Yes / No
3. Select Print on the screen for printing.
Or Cancel to go back to Print Mode.
Start Printing
• LCD monitor appears "Now printing…".
• Or press Menu button to stop printing
anytime.
80
Appendix
About Folder and File Names
Your camera automatically creates specific directories of folders in the internal
memory cards to organize captured images and video files.
File Naming
File names begin with "DSCI" and followed by a 4-digit number that increases in
sequence. File numbering starts from 0001 when a new folder is created.
The highest file number is 9999, if exceeds 9999, the camera will start over the
file number from 0001.
Do not change the folder and file names in the memory card using
your PC. It may be unable to playback the data using the camera.
Troubleshooting
Problem
Camera does not
turn on.
Camera turns off
automatically.
Cause and/or Action
The battery may be exhausted, charge or replace.
•
Power Saving may have activated. Turn power back on.
•
The battery may be exhausted. Charge the battery.
Empty battery
icon is displayed
on the LCD, then Battery is exhausted, please replace or recharge.
the camera turns
off.
LCD monitor
displays "Not
available for this
file".
Function is only available for specific file types. File format
is not supported.
LCD monitor
displays
"Memory full".
Memory card is full. Replace the memory card with a new
one or delete unnecessary images.
LCD monitor
displays "File
locked".
This file is locked. Unlock the file. See "Protect" on page
64.
81
Problem
LCD monitor
displays "Card
locked".
LCD monitor
displays "Card
error".
LCD monitor
displays
"Memory card is
damaged".
LCD monitor
displays "Copy
error".
No image
displays on the
TV screen.
Cause and/or Action
The memory card is protected. Remove the card and slide
the write-protect switch to its unlock position.
Memory card format is not supported by the camera.
Please go to Setup menu to format the card.
The card may be damaged. You can either change the
card or wipe to clean the connected points.
The memory card is protected. Remove the card and slide
the write-protect switch to its unlock position.
The memory card is full. Replace card or delete
unnecessary files.
Incorrect TV-out type was selected. Set the correct TV-out
type to match your TV system.
Do not force the lens to go back.
The lens got
stuck up.
The type of the battery used may be incorrect or the
battery power level is too low. Change the battery or
charge the battery before using the camera.
82
Specifications
Sensor
Lens
LCD monitor
20M Pixels
Focal Length: 26 mm ~ 130 mm
5x optical zoom, 8x digital zoom
2.7" Color LCD
Normal:
Wide: 5 cm ~ infinity
Tele: 60 cm ~ infinity
Focusing Range
Macro:
Wide: 5 cm ~ 100 cm
Tele: 150 cm ~ 200 cm
Super Macro:
Wide: 3 cm
Aperture
Wide: F3.2; Tele: F6.4
Shutter Speed:
Auto: 1 - 1/2,000 sec.
Shutter
Manual: 15 - 1/2,000 sec.
Night: 1/4 - 1/2,000 sec.
Fireworks: 4 sec.
Still Image: EXIF 2.3 compatible format (JPEG compression)
File Format
AVI (Video: MJPEG , Audio: mono)
Audio: WAV
Aspect ratio 4:3
20M (5152 x 3864), 8M (3264 x 2448), 5M (2592 x 1944),
3M (2048 x 1536), VGA (640 x 480)
Aspect ratio 3:2
Resolution
(Photo)
5152 X 3435
Aspect ratio 16:9
14M (5152 x 2898), 2M (1920 x 1080)
Aspect ratio 1:1
2992 x 2992
83
Resolution
(Movie)
•
720p30
•
VGAp30
Scene Mode
Intelligent Scene, Program, Portrait, Landscape, Sunset,
Backlight, Kids, Night Scene, Fireworks, Snow, Sports,
Party, Candlelight, Night Portrait, Soft Skin, Flowing Water,
Food, Love Portrait, Self Portrait, D-Lighting, Time Lapse,
Panorama, Art Effect
ISO Equivalent
Auto, ISO 100, ISO 200, ISO 400, ISO 800, ISO 1600, ISO
3200, ISO 6400
Maximum ISO
Auto
ISO 200, ISO 400, ISO 800
White Balance
Auto White Balance, Daylight, Cloudy, Tungsten,
Fluorescent 1, Fluorescent 2, Custom
Exposure Control
+2.0EV / +1.7EV / +1.3EV / +1.0EV / +0.7EV / +0.3EV /
0EV / -0.3EV / -0.7EV/ -1.0EV / -1.3EV / -1.7EV / -2.0EV
Metering
Multi, Center, Spot
Self-timer
Off, 10 sec., 2 sec., Double
Flash
Auto Flash, Red-eye Reduction, Forced On, Slow Sync,
Forced Off
Internal memory: 64MB flash memory
Storage
External memory: SD (up to 4GB), SDHC card (up to 32GB
guaranteed), SDXC card (up to 64GB guaranteed)
OSD Language
Interface
USB/AV OUT
TV system
NTSC/PAL (selected by Setup MENU)
Battery
Lithium ion battery
Full-Half (65% ± 15%)
Battery Level
Half-Low (25% ± 15%)
Low-Exhausted (10% ± 10%)
USB adapter
Rated input voltage: AC 100V-240V (160mA, 50/60Hz)
84
Rated output voltage: DC 5V/1A
Operating temperature: 0ºC - 40ºC
Operating
Temperature
0ºC - 40ºC
Operating
Humidity
0% - 90%
Microphone
Built-in
Speaker
Built-in
Dimensions
Weight
100.39 x 59.00 x 21.45 (mm)
103 g (no battery)
85
Download PDF
Similar pages