Operating Instructions
Colour Laser Multi-Function Printer
Model No.
KX-MC6020C
Do NOT connect the unit to a computer with USB cable until prompted by the Multi-Function
Station (CD-ROM).
1
2
Designed to be used only in Canada.
L This unit is compatible with Call Display. You must subscribe to the appropriate service
offered by your service provider/telephone company.
Thank you for purchasing a Panasonic MultiFunction Printer.
You can select English or French for the language.
The display and reports will be in the selected language.
The default setting is English. If you want to change the
setting, see feature #110 on page 57.
Caution:
L Do not rub or use an eraser on the printed side of
recording paper, as the print may smear.
Trademarks:
L Microsoft, Windows, Windows Vista and Internet
Explorer are either registered trademarks or
trademarks of Microsoft Corporation in the United
States and/or other countries.
L Pentium is a trademark of Intel Corporation in the
U.S. and other countries.
L Screen shots reprinted with permission from
Microsoft Corporation.
L Adobe and Reader are either registered trademarks
or trademarks of Adobe Systems Incorporated in the
United States and/or other countries.
L 3M is a trademark or registered trademark of 3M
Company.
L Avery is a registered trademark of Avery Dennison
Corporation.
L PCL is a trademark of Hewlett-Packard Company.
L All other trademarks identified herein are the
property of their respective owners.
Copyright:
L This material is copyrighted by Panasonic
Communications Co., Ltd., and may be reproduced
for internal use only. All other reproduction, in whole
or in part, is prohibited without the written consent of
Panasonic Communications Co., Ltd.
© 2008 Panasonic Communications Co., Ltd. All Rights
Reserved.
2
Important Information
Important Information
For your safety
Laser radiation
The printer of this unit utilizes a laser. Use of
controls or adjustments or performance of
procedures other than those specified
herein may result in hazardous radiation
exposure.
Fuser unit
During or immediately after printing, the
fuser unit (1) gets hot. This is normal. Do
not touch the fuser unit.
Note:
L The left side of the unit (2) and the area near the
recording paper exit (3) also get warm. This is also
normal.
3
1
2
For best performance
Toner cartridge and drum cartridge
L When replacing the toner cartridge or drum
cartridge, do not allow dust, water, or liquids to come
in contact with the drum. This may affect print quality.
L For optimal performance, genuine Panasonic toner
cartridges and drum cartridges are recommended.
We cannot be responsible for problems that may be
caused by a non-Panasonic toner cartridge or drum
cartridge:
– Damage to the unit
– Poor print quality
– Improper operation
them, open the drum cartridge protection bag. The
drum cartridge contains a photosensitive drum.
Exposing it to light may damage the drum. Once you
have opened the protection bag:
– Do not expose the drum cartridge to light for
more than 45 seconds.
– Do not touch or scratch the green drum surface.
– Do not place the drum cartridge near dust or dirt,
or in a high humidity area.
– Do not expose the drum cartridge to direct
sunlight.
L To extend the life of the drum cartridge, the power
switch should never be turned OFF immediately after
printing. Leave the power turned ON for a minimum
of 30 minutes after printing.
Location
L To avoid malfunction, do not position the unit near
appliances such as TVs or speakers which generate
an intense magnetic field.
Static electricity
L To prevent static electricity damage to the interface
connectors or other electrical components inside the
unit, touch a grounded metal surface before touching
the components.
Environment
L Keep the unit away from electrical noise generating
devices, such as fluorescent lamps and motors.
L The unit should be kept free from dust, high
temperature and vibration.
L The unit should not be exposed to direct sunlight.
L Do not place heavy objects on top of the unit. When
you leave the unit unused for a long period of time,
unplug this unit from the power outlet.
L The unit should be kept away from heat sources such
as heaters, kitchen stoves, etc. Damp basements
should also be avoided.
L In the printing process, heat is used to fuse toner
onto the page. As a result, it is normal for the
machine to produce an odour during and shortly after
printing. Be sure to use this unit in an area with
proper ventilation.
L Do not place any objects within 10 cm (4 inches) of
the right, left and back sides of the unit.
Toner cartridge
L Do not leave the toner cartridge out of the protection
bag for a long time. It will decrease the toner life.
Drum cartridge
L Read the instructions on page 10 before you begin
installation of the drum cartridge. After you have read
3
Important Information
L Do not cover slots or openings on the unit. Inspect
the air circulation vents regularly and remove any
dust build-up with a vacuum cleaner (1).
Approx. 30 kg (67 lb)
1
Routine care
L Wipe the outer surface of the unit with a soft cloth. Do
not use benzine, thinner, or any abrasive powder.
Moving the unit
The unit weighs approximately 30 kg (67 lb). It is highly
recommended that two people handle this unit.
When moving the unit, hold both of the side grips (2).
2
Illegal copies
L It is unlawful to make copies of certain
documents.
Copying certain documents may be illegal in your
country. Penalties of fines and/or imprisonment may
be imposed on those found guilty. The following are
examples of items that may be illegal to copy in your
country.
– Currency
– Bank notes and checks
– Bank and government bonds and securities
– Passports and identification cards
– Copyright material or trademarks without the
consent of the owner
– Postage stamps and other negotiable
instruments
This list is not inclusive and no liability is
assumed for either its completeness or accuracy.
In case of doubt, contact your legal counsel.
Notice:
L Install your machine near a supervised area to
prevent illegal copies from being made.
2
4
Table of Contents
1. Introduction and Installation
1. Table of Contents
Accessories
1.1
1.2
Supplied accessories .................................... 7
Accessory information ................................... 7
Finding the Controls
1.3
1.4
Button descriptions........................................ 8
Overview ....................................................... 9
Installation
1.5
1.6
Toner cartridge and drum cartridge............. 10
Recording paper.......................................... 14
2. Preparation
Connections and Setup
2.1
2.2
2.3
2.4
Connections ................................................ 17
Turning the power switch ON....................... 18
Dialing mode ............................................... 18
Selecting the operation mode (Scan/Copy/Fax)
.................................................................... 19
Document Requirements
2.5
Setting the original....................................... 19
Help
2.6
Help function ............................................... 21
Volume
2.7
Date and time .............................................. 22
Your logo...................................................... 22
Your fax number .......................................... 23
Configuring the unit to access the LAN ....... 23
Installing Multi-Function Station .................. 24
Starting Multi-Function Station .................... 26
3. Printer
Printer
3.1
3.2
Printing from Windows applications ............ 28
Printing a received e-mail attachment
automatically (LAN connection only) ........... 30
4. Scanner
Scanner
4.1
4.2
Scanning from the unit (Push Scan)............ 32
Scanning from a computer (Pull Scan)........ 34
5. Copier
Copy
5.1
5.2
Broadcast transmission................................46
Sending a computer document as a fax
message from your computer ......................48
Receiving Faxes
6.6
Receiving a fax automatically – Auto answer
ON................................................................48
6.7 Receiving a fax manually – Auto answer OFF
.....................................................................49
6.8 Using the unit with an answering machine...50
6.9 Junk fax prohibitor (preventing fax reception
from undesired callers).................................51
6.10 Receiving a fax on your computer................52
7. Call Display
Call Display
7.1
7.2
7.3
7.4
Call Display service......................................53
Viewing and calling back using caller
information ...................................................53
Erasing caller information.............................54
Storing caller information .............................54
8. Distinctive Ring
Distinctive Ring
Adjusting the volume ................................... 21
Initial Programming
2.8
2.9
2.10
2.11
2.12
2.13
6.4
6.5
Making a copy ............................................. 36
More copying features ................................. 37
8.1
8.2
8.3
8.4
Distinctive Ring service ................................55
Using two or more phone numbers on a single
telephone line...............................................55
Using three or more phone numbers on a
single telephone line ....................................55
Programming the ring pattern assigned for fax
.....................................................................55
9. Programmable Features
Features Summary
9.1
9.2
9.3
9.4
9.5
9.6
9.7
9.8
Programming................................................56
Basic features ..............................................57
Fax features .................................................61
Copy features ...............................................65
PC print features ..........................................66
Scan features ...............................................69
LAN features ................................................71
Network features (LAN connection only)......73
10.Useful Information
Useful Information
10.1
10.2
10.3
10.4
Character entry ............................................75
Status of the unit ..........................................76
Cancelling the operations.............................77
Changing the colour calibration....................77
Option
6. Fax
Sending Faxes
6.1
6.2
6.3
Sending a fax manually ............................... 43
Storing items for the one-touch dial feature and
navigator directory....................................... 44
Sending a fax using one-touch dial feature and
navigator directory....................................... 45
10.5
10.6
10.7
10.8
Optional handset unit ...................................78
Optional automatic duplex unit.....................80
Optional input tray ........................................80
Setting the optional input tray/optional
automatic duplex unit ...................................81
5
Table of Contents
11.Help
Error Messages
11.1 Error messages – Reports .......................... 82
11.2 Error messages – Display ........................... 83
Troubleshooting
11.3 When a function does not work ................... 86
12.Paper Jams
Jams
12.1 Recording paper jam ................................... 95
12.2 Document jams (Automatic document feeder)
.................................................................. 100
13.Cleaning
Cleaning
13.1 Cleaning the white plates and glass.......... 101
13.2 Cleaning the document feeder rollers........ 102
13.3 Cleaning the paper chute .......................... 103
14.General Information
Printed Reports
14.1 Reference lists and reports ....................... 104
Specifications
14.2 Specifications ............................................ 105
Copyrights
14.3 Information of copyrights and licences ...... 108
15.Index
15.1 Index......................................................... 118
6
1. Introduction and Installation
1 Introduction and Installation
Accessories
1.1 Supplied accessories
1.2 Accessory information
1 Toner cartridge (starter)
(Cyan/Magenta/Yellow/Black)*1
To ensure that the unit operates properly, we
recommend the use of Panasonic toner cartridge and
drum cartridge.
■ Replacement accessory
– Toner cartridge
2 Colour drum cartridge
3 Monochrome drum
cartridge
4 Waste toner cartridge 5 CD-ROM
(pre-installed inside the
unit)
6 Quick reference guide
–
7 Quick installation guide
–
–
–
8 Power cord
9 Telephone line cord
Colour
Model No. (Part No.)
Cyan
KX-FATC501A
Magenta
KX-FATM502A
Yellow
KX-FATY503A
Black
KX-FATK504A
L Prints about 2,000 sheets of letter-size pages
with a 5 % coverage using KX-FATC501A/KXFATM502A/KX-FATY503A and about 2,500
sheets using KX-FATK504A.
Toner cartridge (high capacity)
Colour
Model No. (Part No.)
Cyan
KX-FATC506A
Magenta
KX-FATM507A
Yellow
KX-FATY508A
Black
KX-FATK509A
L Prints about 4,000 sheets of letter-size pages
with a 5 % coverage.
Colour drum cartridge
L Model No. (Part No.): KX-FADC510A
Monochrome drum cartridge
L Model No. (Part No.): KX-FADK511A
Waste toner cartridge
L Model No. (Part No.): KX-FAW505A
■ Optional accessory
– Optional lower input tray
L Model No. (Part No.): KX-FAP317A
– Automatic duplex unit
L Model No. (Part No.): KX-FAB318A
– Handset unit
L Model No. (Part No.): KX-FA103A
*1 Prints about 1,000 letter-size pages with a 5 %
coverage (page 106).
Note:
L Save the original carton and packing materials for
future shipping and transportation of the unit.
L After unpacking the product, take care of the power
plug cap and/or packing materials appropriately.
L Do not remove the drum cartridges and toner
cartridges from the unit when repacking the unit for
shipping and transportation.
7
1. Introduction and Installation
N Station keys
Finding the Controls
L To use the one-touch dial feature (page 44, 45).
1.3 Button descriptions
AB CDEFG
H IJ K
L
O {Broadcast}
L To send a document to multiple parties (page 46).
P {Manual Broad}
L To send a document to multiple parties by storing
using the dial keypad (page 46).
Q {Lower}
L To select stations 4–6 for the one-touch dial
feature (page 44, 45).
M
NO
P Q R S T U
V
W
A {Copy}
L To switch to the copy mode (page 19, 36).
B {Scan}
L To switch to the scan mode (page 19, 32).
C {Collate}{Directory}
L To make a collated copy (page 38).
L To initiate the navigator directory (page 45, 47).
D {Contrast}
L To select a contrast when copying (page 36).
L To select a contrast when sending a fax (page
43).
E {Resolution}
L To select a resolution when copying (page 36).
L To select a resolution when sending a fax (page
43).
F {Zoom}{Quick Scan}
L To enlarge or reduce a document when copying
(page 37).
L To store a scanned document into memory, and
then send it (page 44).
G {Page Layout}{Call Display}
L To make various page layout copies (page 39).
L To use Call Display features (page 53).
H {Menu}
L To start or exit programming.
I {Redial}{Pause}
L To redial the last number dialed. If the line is busy
when you send a fax, the unit will automatically
redial the number 1 time.
L To insert a pause during dialing.
J {Flash}
L To access special telephone services or for
transferring extension calls.
K {Tone}
L To change from pulse to tone temporarily during
dialing when your line has rotary/pulse service.
L {Fax Auto Answer}
L To turn the auto answer setting ON/OFF (page
48).
M {Fax}
L To switch to the fax mode (page 19, 43).
8
R Navigator key
L To select desired settings.
L To adjust the volume (page 21).
L To search for a stored item (page 45).
S {Set}
L To store a setting during programming.
T {Monitor}
L To initiate dialing.
When you press {Monitor} while receiving a call,
you will be able to hear the other party, but the
other party will not be able to hear you.
U {Black}
L To copy a document in monochrome (page 36).
L To scan a document in monochrome (push scan)
(page 32).
L To send or receive a fax (page 43, 49).
V {Colour}
L To copy a document in colour.
L To scan a document in colour (push scan).
W {Stop}
L To stop an operation or programming session.
L To erase a character/number.
1. Introduction and Installation
1.4.2 Rear view
1.4 Overview
A
1.4.1 Front view
1 2 345
B
6
7
8
9
o
C D
j
1
2
3
4
5
6
7
8
9
j
k
l
m
n
o
E G
F
k lmn
ADF (Automatic Document Feeder) cover
Document guides
Document tray
Document tray extender
Document cover
Document exit
Document entrance
Power switch
Left cover
Handset unit (optional) connection jack
Left cover open lever
Handset cord holder
Standard input tray
Front cover
Recording paper exit*1
p
p Waste toner cartridge (pre-installed inside the
unit)*2
H
A
B
C
D
E
F
G
H
Speaker
Power inlet
Telephone line jack
External telephone jack
LAN interface connector
LED
USB interface connector
Automatic duplex unit (optional) connector
Removing the shipping tape
Remove the shipping tape (1).
1
Note:
L Shipping tape positions are subject to change
without notice.
*1 The unit can hold up to approximately 100 sheets of
printed paper. Remove the printed paper before the
recording paper exit becomes full.
*2 The waste toner cartridge stores toner that is
discharged during printing. See page 107 for
information on the waste toner cartridge life.
9
1. Introduction and Installation
2 Unlock the drum cartridge cover by pushing the tabs
Installation
1.5 Toner cartridge and drum
cartridge
The supplied toner cartridge is a starter toner cartridge.
Caution:
L Read the following instructions before you begin
installation. After you have read them, open the
drum cartridge protection bag. The drum
cartridge contains a photosensitive drum.
Exposing it to light may damage the drum. Once
you have opened the protection bag:
– Do not expose the drum cartridge to light for
more than 45 seconds.
– Do not touch or scratch the green drum
surface at the bottom of the drum cartridge.
– Do not place the drum cartridge near dust or
dirt, or in a high humidity area.
– Do not expose the drum cartridge to direct
sunlight.
L Do not leave the toner cartridge out of the
protection bag for a long time. It will decrease the
toner life.
L We cannot be responsible for any damage to the
unit or degradation of print quality which may
occur from the use of a non-Panasonic toner
cartridge and drum cartridge.
L Do not add toner to the toner cartridge.
(2) in the direction of the arrows.
2
3 Lift up the levers (3) and open the drum cartridge
cover (4).
1 Open the front cover (1) by holding the centre part.
3
1
4
10
1. Introduction and Installation
4 Remove the orange protector (5) by pulling it
toward you, then pull it completely out from the unit.
6 Remove the protective caps (6), then detach the
upper seal cover by holding the tab (7).
6
7
5
7 Firmly grip the colour drum cartridge (8) and
remove the protective tray (9) by sliding it toward
you.
8
9
L Do not touch or scratch the green drum surface
(j) at the bottom of the drum cartridge.
5 Remove the colour drum cartridge from the
protection bag.
j
8 Hold the green lever (k) of the colour drum
L Remove the shipping tape.
L Do not remove the monochrome drum cartridge
from the protection bag before installing the
colour drum cartridge in step 8.
L When holding the colour drum cartridge, be sure
to handle it over a table to prevent damage
caused by dropping it from a high position.
cartridge (l) using your left hand, and hold the front
part using your right hand. Then insert it into the left
side of the unit.
L Make sure that the arrows (m) match to insert
the drum cartridge correctly.
11
1. Introduction and Installation
L Do not touch or scratch the accumulator unit
(n).
11 Firmly grip the monochrome drum cartridge (q) and
remove the protective tray (r) by sliding it toward
you.
m
q
k
r
L Do not touch or scratch the green drum surface
(s) at the bottom of the drum cartridge.
l
s
n
9 Remove the monochrome drum cartridge from the
protection bag.
12 Insert the monochrome drum cartridge (t) into the
right side of the unit.
L Make sure that the arrows (u) match to insert
the drum cartridge correctly.
L Do not touch or scratch the accumulator unit
(v).
u
L Remove the shipping tape.
10 Remove the protective cap (o), then detach the
upper seal cover by holding the tab (p).
p
o
t
v
12
1. Introduction and Installation
13 Before opening the protection bag of the new toner
17 Lift the drum cartridge cover (a) and push down on
cartridges, shake them vertically more than 10
times.
the levers (b) to close.
L Push the levers down until you hear a click to
ensure that the cover is locked.
a
14 Remove the 4 toner cartridges from the protection
bags.
L Remove the shipping tape.
15 Remove each protective tray (w) by lifting up the
toner cartridge (x).
x
w
b
16 Insert each toner cartridge (y) in the appropriate
colour slot.
From left to right, yellow, magenta, cyan, black.
L Make sure that the arrows (z) match to insert
the toner cartridge correctly.
L Do not touch the toner cartridge shutter at the
bottom of the toner cartridge. The toner may spill
out of the toner cartridge.
18 Close the front cover.
z
y
When to replace the toner cartridge and the drum
cartridge
When the display shows the following, replace the toner
cartridge.
– “BLACK TONER LOW”
13
1. Introduction and Installation
–
–
–
“CYAN TONER LOW”
“MAGENTA TONER LOW”
“YELLOW TONER LOW”
–
–
–
–
“BLACK TONER EMPTY”
“CYAN TONER EMPTY”
“MAGENTA TONER EMPTY”
“YELLOW TONER EMPTY”
When the display shows the following, replace the drum
cartridge.
– “COLOUR DRUM LIFE LOW”
– “MONOCHROME DRUM LIFE LOW”
–
–
“COLOUR DRUM REPLACE”
“MONOCHROME DRUM REPLACE”
Note:
L When replacing the toner cartridge, be sure to seal
the used toner cartridge in a plastic bag or other
container so that toner does not spill out of it.
L When replacing the colour drum cartridge, hold the
green lever using your left hand same as installing it.
See step 8 on page 11 for instructions.
L To ensure that the unit operates properly, we
recommend the use of Panasonic toner cartridge
and drum cartridge. See page 7 for accessory
information.
L See page 106 for information on toner life and drum
life.
1.6 Recording paper
The standard input tray unit can hold:
– Up to 250 sheets of 75 g/m2 (20 lb) paper.
– Up to 230 sheets of 80 g/m2 (21 lb) paper.
– Up to 200 sheets of 90 g/m2 (24 lb) paper.
– Up to 180 sheets of 105 g/m2 (28 lb) paper.
– Up to 25 transparencies.*1
– Up to 25 labels.*1
– Up to 10 envelopes.*1
– Up to 10 card stocks.*1
*1 Only when using the unit as a printer. See page 29
for details.
L Please refer to page 106 for information on recording
paper.
L The unit is set for printing letter-size plain paper
by default.
– To use A4 or legal-size paper, change the
recording paper size setting (feature #380 on
page 58).
– To use thin or thick paper, change the
recording paper type setting (feature #383 on
page 59).
1 Pull the standard input tray (1) until it clicks into
place, then pull it completely out, lifting the front part
of the tray.
Waste disposal method
Waste material should be disposed of under conditions
which meet all national and local environmental
regulations.
Toner save feature
If you want to reduce toner consumption, set the toner
save setting to ON (feature #482 on page 59). The toner
cartridge will last approximately 40 % longer. This
feature may lower the print quality.
1
2 Before loading a stack of paper, fan the paper to
prevent paper jams.
14
1. Introduction and Installation
3 Load the paper, print-side up (2).
Important:
L Push and lock the plate (3) in the standard
input tray, if it is lifted.
paper is under the paper limit mark (7). The
paper should not be loaded over the tab (8).
7
6
8
3
2
4 Pinch the right side of the recording paper guide
(4), then slide it to match the paper size mark.
Pinch the front and back recording paper guides (5)
at the same time, then slide them together to match
the paper size mark.
5
6
5 Insert the standard input tray to the unit, lifting the
front part of the tray. Then push it completely into the
unit.
5
4
L Make sure that the recording paper guides (6)
are at the paper size mark and the recording
Note:
L If the paper is not loaded correctly, re-adjust the
paper guides, or the paper may jam.
L If the standard input tray does not close, the plate in
the standard input tray may be lifted. Push the paper
and make sure that the paper is laid flat in the
standard input tray.
15
1. Introduction and Installation
Caution for the standard input tray
L Do not drop the standard input tray.
L Hold the standard input tray with both hands
when removing or installing. The standard input
tray weighs approximately 2.9 kg (6.4 lb) when
the recording paper is fully installed.
Do not touch the plate (1) on the left side of the
standard input tray.
1
Approx. 2.9 kg (6.4 lb)
16
2. Preparation
2 Preparationand Setup
Connections
2.1 Connections
Caution:
L When you operate this product, the power outlet
should be near the product and easily
accessible.
IMPORTANT NOTICE FOR THE USB
CONNECTION
L DO NOT CONNECT THE UNIT TO A
COMPUTER WITH USB CABLE UNTIL
PROMPTED BY THE MULTI-FUNCTION
STATION (page 24).
Note:
L If any other device is connected to the same
telephone line, this unit may disturb the network
condition of the device.
8
Using surge protectors
L The warranty does not cover damage due to power
line surges or lightning. For additional protection, we
recommend using surge protectors (j).
If the unit shares a single telephone line with a DSL
service
Fax transmission/reception may be disturbed, noise
interference may be heard during telephone
conversations, or Call Display (page 53) may not
function properly. Please attach a DSL filter (k) to the
telephone line cord of the unit to prevent this. DSL filter is
provided by your DSL service provider.
9
3
7
5
4
6
1
2
j
1 Power cord
L Connect to a power outlet
(120 V, 60 Hz).
2 Telephone line cord
L Connect to a single telephone line jack (RJ11C).
3 [EXT] jack
L You can connect an answering machine or an
extension telephone. Remove the stopper if
attached.
4 Answering machine (not supplied)
5 To the internet
6 Network router/Network hub (not supplied)
L Also connect networked computers.
7 LAN cable (not supplied)
L To assure continued emission limit compliance,
use only shielded LAN cable (category 5 straight
cable).
8 Handset unit (optional) connection jack
L You can connect the optional handset unit (page
78). Remove the cover if attached.
9 Automatic duplex unit (optional) connector
k
Using network router/network hub
L We recommend using network routers/network hubs
(6) to use the unit under sufficient security
condition. Consult your network administrator for
firewall settings, etc.
L The warranty does not cover damage due to security
problems or any disadvantages relating to it.
17
2. Preparation
2.2 Turning the power switch ON
2.3 Dialing mode
Turn the power switch to the ON position (1).
If you cannot dial (page 43), change this setting
according to your telephone line service.
1
{Menu}
{Set}
1 {Menu}
2 Press {#}{1}{2}{0} to display “DIALING MODE”.
3 Press {1} or {2} to select the desired setting.
{1} “PULSE”: For rotary/pulse dial service.
{2} “TONE” (default): For tone dial service.
4 {Set}
5 Press {Menu} to exit.
18
2. Preparation
Document Requirements
2.4 Selecting the operation mode
(Scan/Copy/Fax)
You can select the desired mode by pressing one of the
following buttons.
2.5 Setting the original
2.5.1 Using the scanner glass
1
2
–
–
–
{Scan}: Select this mode when using the unit as a
scanner (page 32).
{Copy}: Select this mode when using the unit as a
copier (page 36).
{Fax}: Select this mode when using the unit as a fax
machine (page 43).
Note:
L The default operation mode is the copy mode.
L You can change the default operation mode (feature
#463 on page 59) and the timer before returning to
the default operation mode (feature #464 on page
59).
1 Open the document cover (1).
2 Place the document FACE DOWN on the scanner
glass (2), aligning the top left of the document with
the corner to which the m mark points.
3 Close the document cover.
Note:
L Confirm that there are no documents in the
automatic document feeder.
L Place the original onto the scanner glass gently. Do
not press down too firmly to avoid malfunction.
L If the original is a thick book, do not close the
document cover.
L Check that any ink, paste or correction fluid has dried
completely.
L Effective scanning area is as follows:
Effective scanning area
L Shaded area will be scanned.
4 mm
(5/32")
208 mm
(8 3/16")
4 mm
(5/32")
4 mm
(5/32")
347 mm
(13 11/16")
4 mm
(5/32")
19
2. Preparation
Minimum document size
148 mm
(6")
2.5.2 Using the automatic document feeder
1
148 mm
(6")
600 mm
(23 5/8")
Maximum document size
216 mm
(8 1/2")
1 Insert the document (up to 50 pages) FACE UP into
the feeder until a single beep is heard.
2 Adjust the width of the document guides (1) to fit
Effective scanning area
L Shaded area will be scanned.
the actual size of the document.
Note:
L Confirm that there are no documents on the scanner
glass.
L Check that any ink, paste or correction fluid has dried
completely.
L Remove clips, staples or other fasteners.
L Do not insert the following types of documents:
(Make a copy of the document using the scanner
glass and set the copy instead.)
– Chemically treated paper such as carbon or
carbonless duplicating paper
– Electrostatically charged paper
– Badly curled, creased or torn paper
– Paper with a coated surface
– Paper with printing on the opposite side that can
be seen through the other side, such as
newsprint
L The total height of the documents when laid flat,
must be less than 5 mm (3/16"). If the documents
exceed the capacity of the automatic document
feeder, they may fall or cause a jam in the feeder.
L To set a document with a width of less than 210 mm
(8 1/4"), we recommend using the scanner glass to
copy the original document onto A4 or letter-size
paper, then setting the copied document.
L Do not set documents that do not satisfy the
requirements of size and weight. Make a copy of the
document using the scanner glass and set the copy.
L Available document size, document weight and
effective scanning area are as follows:
20
4 mm (5/32")
4 mm (5/32")
4 mm (5/32")
4 mm (5/32")
208 mm (8 3/16")
216 mm (8 1/2")
Document weight
L Single sheet:
45 g/m2 to 90 g/m2 (12 lb to 24 lb)
L Multiple sheets:
60 g/m2 to 80 g/m2 (16 lb to 21 lb)
Using the document tray extender
When you insert the legal-size paper, open the
document tray extender (1).
1
2. Preparation
Help
Volume
2.6 Help function
2.7 Adjusting the volume
The unit contains helpful information, which can be
printed for reference.
– “BASIC SETTINGS”
– “FEATURE LIST”
– “DIRECTORY”
– “FAX RECEIVING”
– “COPIER”
– “REPORTS”
– “CALL DISPLAY”
Important:
L Before adjusting the volume, set the operation
mode to fax mode. If the {Fax} light is OFF, turn it
ON by pressing {Fax}.
{Menu}
{Fax}
{Set} {V}{^}
Ringer volume
While the unit is idle, press {V} or {^}.
L The ringer volume can only be adjusted if there are
no documents in the document entrance.
{Set} {<}{>}
1 Press {Menu} repeatedly to display “HELP”.
2 Press {<} or {>} repeatedly to display the desired
item. i {Set}
3 Press {Menu} to exit.
To turn the ringer OFF
Press {V} repeatedly to display “RINGER OFF= OK?”.
i {Set}
L The unit will not ring.
L To turn the ringer back ON, press {^}.
Monitor volume
While using the monitor, press {V} or {^}.
21
2. Preparation
Initial Programming
2.8 Date and time
2.9 Your logo
You can program your logo (name, company name, etc.)
so that it appears on the top of each page sent.
{Menu}
{Menu}
{Fax}
{Set} {<}{>}
1 {Menu} i {#}{1}{0}{1} i {Set}
M:|
01/D:01/Y:08
TIME: 12:00AM
2 Enter the current month/date/year/hour/minute by
selecting 2 digits for each.
Example: August 10, 2008 10:15 PM (12 hour
clock format)
1. Press {0}{8} {1}{0} {0}{8} {1}{0} {1}{5}.
M:|
08/D:10/Y:08
TIME: 10:15AM
2. Press {*} repeatedly to select “PM”.
3 {Set}
4 Press {Menu} to exit.
Note:
L The other party’s fax machine will print the date and
time on the top of each page you send according to
your unit’s date and time setting.
L After setting the date and time, if the unit is in the
copy mode, change it to the fax mode by pressing
{Fax}. You can check your unit’s date and time
setting on the display.
L If you select French for the language (feature #110
on page 57), the time is set using a 24 hour clock.
Example: 15:15
Press {1}{5}{1}{5}.
To correct a mistake
Press {<} or {>} to move the cursor to the incorrect
number, and make the correction.
If you have subscribed to a Call Display service
The date and time will be automatically set according to
the received caller information.
L If the time has not previously been set, Call Display
will not adjust the clock.
L You can turn this feature OFF (feature #226 on page
58).
22
{Set} {<}{>}
{Stop}
1 {Menu} i {#}{1}{0}{2} i {Set}
LOGO=|
2 Enter your logo, up to 30 characters (see page 75 for
character entry). i {Set}
3 Press {Menu} to exit.
To correct a mistake
Press {<} or {>} to move the cursor to the incorrect
character, and make the correction.
L To erase all characters, press and hold {Stop}.
2. Preparation
2.10 Your fax number
You can program your fax number so that it appears on
the top of each page sent.
{Menu}
{Flash}
{Set} {<}{>}
{Stop}
1 {Menu} i {#}{1}{0}{3} i {Set}
NO.=|
2 Enter your fax number, up to 20 digits.
L
L
L
L
To enter a “+”, press {*}.
To enter a space, press {#}.
To enter a hyphen, press {Flash}.
To erase a number, press {Stop}.
3 {Set}
4 Press {Menu} to exit.
To correct a mistake
Press {<} or {>} to move the cursor to the incorrect
number, and make the correction.
L To erase all numbers, press and hold {Stop}.
2.11 Configuring the unit to
access the LAN
You can print documents, scan documents, receive
faxes or send faxes using a computer on the LAN. To
enable these features, you need to set the IP address,
subnet mask, and default gateway for the unit.
Important:
L Consult your network administrator when setting
the IP address, subnet mask, and default
gateway.
2.11.1 Setting up automatically with a
DHCP server
Your situation:
– When only one unit is connected to the LAN.
If your network administrator manages the network with
a DHCP (Dynamic Host Configuration Protocol) server, it
will automatically assign an IP (Internet Protocol)
address, subnet mask, and default gateway to the unit.
1 After connecting the LAN cable to the unit and the
computer, turn the power switch ON.
L The IP address, subnet mask, and default
gateway will be set automatically.
2 Install Multi-Function Station on the computer that
you want to use it with. See page 24 for details.
Note:
L You can connect two or more units and assign IP
addresses automatically with a DHCP server, but we
recommend assigning static IP addresses manually
for each unit to avoid unnecessary trouble.
2.11.2 Setting up manually
Your situation:
– When your network administrator does not manage
the network with a DHCP server.
– When two or more units are connected to the LAN.
You need to assign an IP address, subnet mask, and
default gateway manually.
1
2
3
4
{Menu}
Press {#}{5}{0}{0} to display “DHCP”.
Press {0} to select “DISABLED”. i {Set}
Set each item.
For the IP address:
1. Press {5}{0}{1} to display “IP ADDRESS”.
2. {Set} i Enter the IP address of the unit. i
{Set}
For the subnet mask:
1. Press {5}{0}{2} to display “SUBNET MASK”.
2. {Set} i Enter the subnet mask of the network.
i {Set}
23
2. Preparation
For the default gateway:
1. Press {5}{0}{3} to display “DEFAULT
GATEWAY”.
2. {Set} i Enter the default gateway of the
network. i {Set}
5 Press {Menu} to exit.
6 Install Multi-Function Station on the computer that
you want to use it with. See page 24 for details.
To correct a mistake in the IP address, subnet mask,
or default gateway
Press {<} or {>} to move the cursor to the incorrect
number, and make the correction.
2.11.3 Setting the computer for PC fax
reception
You need to select the computer that will be used for
receiving faxes.
L Make sure PC fax setting is turned ON beforehand
(feature #442 on page 64).
1 {Menu} i {#}{4}{4}{3} i {Set}
2 Press {V} or {^} repeatedly to select the desired
computer. i {Set}
3 Press {Menu} to exit.
Note:
L If the unit is not connected to the LAN, the computer
connected to the unit by USB is assigned as the
default computer for PC fax reception.
L To select the desired computer easily, change the PC
name beforehand (page 27).
2.12 Installing Multi-Function
Station
2.12.1 Required computer environment
Panasonic Multi-Function Station software enables the
unit to carry out the following functions:
– Printing on plain paper, thin and thick paper,
transparencies, labels, envelopes and card stocks
– Scanning documents and converting an image into
text with Readiris OCR software
– Scanning from other applications for Microsoft®
Windows® that support TWAIN scanning and WIA
scanning (Windows XP/Windows Vista®, USB
connection only)
– Storing, editing or erasing items in directories using
your computer
– Programming the features using your computer
– Sending, receiving fax documents using your
computer
To use Multi-Function Station on your computer, the
following are required:
Operating System:
Windows 98/Windows Me/Windows 2000/Windows
XP/Windows Vista
CPU:
Windows 98/Windows Me/Windows 2000: Pentium® y
or higher processor
Windows XP: Pentium z or higher processor
Windows Vista: Pentium 4 or higher processor
RAM:
Windows 98/Windows Me: 64 MB (128 MB or more
recommended)
Windows 2000/Windows XP: 128 MB (256 MB or more
recommended)
Windows Vista: 512 MB (1,024 MB or more
recommended)
Other Hardware:
CD-ROM drive
Hard disk drive with at least 150 MB of available space
USB interface
LAN interface (10Base-T/100Base-TX)
Other:
Internet Explorer® 5.0 or later
Warning:
L To assure continued emission limit compliance;
– use only shielded USB cable (Example: HiSpeed USB 2.0 certified cable).
– use only shielded LAN cable (category 5 straight
cable).
L To protect the unit, use only shielded USB cable in
areas where thunderstorms occur.
Note:
L A USB cable is not supplied. Please purchase a
shielded Type-A male/Type-B male USB cable.
24
2. Preparation
2.12.2 Installing Multi-Function Station on
a computer
L Install Multi-Function Station (CD-ROM) before
connecting the unit to a computer with USB
cable. If the unit is connected to a computer with
USB cable before installing Multi-Function
Station, the [Found New Hardware Wizard]
dialogue box will appear. Click [Cancel] to close
it.
L The screenshots shown in these instructions are
for Windows XP and are included for reference
only.
L The screenshots shown in these instructions
may differ slightly from those of the actual
product.
L Software features and appearance are subject to
change without notice.
L If you are using KX-MB200/KX-MB700/KXFLB880 series, see page 94.
1 Start Windows and exit all other applications.
L For Windows 2000, Windows XP and Windows
Vista users, you must be logged in as an
administrator in order to install Multi-Function
Station.
2 Insert the supplied CD-ROM into your CD-ROM
drive.
L If the [Select Language] dialogue box appears,
select the language that you want to use with this
software. Click [OK].
L If the installation does not start automatically:
Click [Start]. Choose [Run...]. Type “D:\Install”
(where “D” is the drive letter of your CD-ROM
drive). Click [OK].
(If you are not sure what the drive letter is for your
CD-ROM drive, use Windows Explorer and look
for the CD-ROM drive.)
3 [Easy Installation]
L The installation will start automatically.
4 When the setup program starts, follow the on-screen
instructions.
L Readiris OCR software (page 33) and Device
Monitor (page 76) will also be installed.
5 The [Connect Type] dialogue box appears.
For USB connection:
1. [Connect directly with a USB cable.] i [Next]
L The [Connect Device] dialogue box will appear.
2. Connect the unit to a computer with the USB cable
(1), then click [Next].
1
L If the unit is connected to your computer, the
model name will be automatically detected.
L You can change the name of the unit if necessary.
3. Click [Install], then follow the on-screen
instructions.
L The files will be copied to your computer.
For LAN connection:
1. [Connect via the Network.] i [Next]
L The [Select a Network Device] dialogue box
will appear.
2. Check [Select in the searched list] and select the
unit from the list.
L If the name of the desired unit is not displayed on
the list, and the IP address for the unit has been
assigned, check [Direct input] and enter the IP
address.
3. [Next]
L You can change the name of the unit if necessary.
4. Click [Install], then follow the on-screen
instructions.
L The files will be copied to your computer.
Important notice
If you use Windows XP or Windows Vista, a message
may appear after connecting the unit with the USB
cable. This is normal and the software will not cause
any difficulties with your operating system. You can
continue the installation with no problem. This kind of
message is displayed:
L For Windows XP users
“The software you are installing for this hardware
has not passed Windows Logo testing to verify its
compatibility with Windows XP.”
L For Windows Vista users
“Would you like to install this device software?”
To view or install the operating instructions data
1. Start Windows and insert the supplied CD-ROM into
your CD-ROM drive.
2. Click [Operating Instructions], then follow the onscreen instructions to view or install the operating
instructions in PDF format.
25
2. Preparation
L Adobe® Reader® is required to view the
operating instructions.
Note:
L If the screen prompts you to insert the CD-ROM for
the operating system when installing Multi-Function
Station, insert it into your CD-ROM drive.
L If you install the operating instructions, you can view
it anytime by clicking [o] on the Multi-Function
Station launcher.
2.13 Starting Multi-Function
Station
[Start] i [All Programs] or [Programs] i
[Panasonic] i the unit’s name i [Multi-Function
Station]
L Multi-Function Station will appear.
To use another unit with the computer
You need to add the printer driver for each unit, as
follows.
1. Start Windows and insert the supplied CD-ROM into
your CD-ROM drive.
2. [Modify] i [Add Multi-Function Station
Driver]. Then follow the on-screen instructions.
Note:
L You cannot connect more than one unit to the same
computer at the same time (USB connection only).
To modify the software (To add or uninstall each
component)
You can select the components to install or uninstall
anytime after the installation.
For Windows 2000, Windows XP and Windows Vista
users, you must be logged in as an administrator in order
to modify Multi-Function Station.
1. Start Windows and insert the supplied CD-ROM into
your CD-ROM drive.
2. [Modify]i [Modify Utilities]. Then follow the onscreen instructions.
To uninstall the software
For Windows 2000, Windows XP and Windows Vista
users, you must be logged in as an administrator in order
to uninstall Multi-Function Station.
[Start] i [All Programs] or [Programs] i
[Panasonic] i the unit’s name i [Uninstall]. Then
follow the on-screen instructions.
[Scan] (page 34)
L To scan and display the scanned images.
L To scan and create an image file.
L To scan and send by e-mail.
L To scan and convert an image into editable text data.
[PC FAX]
L To send a document created on the computer as a
fax message (page 48).
L To display a fax document received on the computer
(page 52).
[Remote Control] (page 76)
L To program the features.
L To store, edit or erase items in directories.
L To view items in the journal report or caller’s list.
L To store caller information into directories.
L To store or erase items for broadcast transmission.
[Utilities]
L To start Multi-Function Viewer (page 34).
L To start Device Monitor (page 76).
L To start OCR application (page 33).
L To start the configuration web page (page 56, 76)
(LAN connection only).
[Settings] (page 27)
L To change the general settings.
L To change the settings for scanning.
[o]
L For detailed instructions on Multi-Function Station.
L To view operating instructions.
[p]
L To display usage tips.
[n]
L To display information about Multi-Function Station.
26
2. Preparation
Note:
L You can confirm if the unit is connected to your
computer by using Device Monitor (page 76).
L Computer features (printing, scanning, etc.) may not
function properly in the following situations:
– When the unit is connected to a computer that
was custom-built by the user.
– When the unit is connected to the computer via a
PCI card or other expansion card.
– When the unit is connected to another piece of
hardware (such as a USB hub or interface
adapter) and not connected directly to the
computer.
For Windows Vista:
1. [Start] i [Control Panel] i [Internet
Options] i [Programs] i [Set programs] i
[Set program access and computer defaults]
L If the [User Account Control] dialogue box
appears, click [Continue].
2. [Custom]
3. Select the desired MAPI-compliant E-mail software
such as [Windows Mail], etc. from [Choose a
default e-mail program]. i [OK]
To change the settings
You can change the settings for Multi-Function Station
beforehand.
1. Select [Settings] from Multi-Function Station.
2. Click the desired tab and change the settings. i
[OK]
[General]
– [Launcher display setting]: To select the display
type of the launcher.
– [OCR Path]: To select the OCR software.
– [PC name list up on device] (LAN connection
only): To select whether or not your computer name
is displayed on the unit.
– [PC name] (LAN connection only): The computer
name that will be displayed on the unit.
[Scan]
– [Save to]: To select the folder where the scanned
image will be saved.
– [Viewer][File][E-Mail][OCR][Custom]: To
change scanning settings for Multi-Function scan
application.
Note:
L Assign a unique name for the [PC name] to avoid
overlapping, or the scanned image may be sent to an
undesired computer.
To select the default E-mail software
The default E-mail software is used when using
“4.1.3 Scan to E-mail”, page 32.
You can select the default E-mail software as follows.
For Windows 98/Windows Me/Windows 2000:
1. [Start] i [Settings] i [Control Panel] i
[Internet Options] i [Programs] i [E-mail]
2. Select the desired MAPI-compliant E-mail software
such as [Outlook Express], etc. i [OK]
For Windows XP:
1. [Start] i [Control Panel] i [Internet
Options] i [Programs] i [E-mail]
2. Select the desired MAPI-compliant E-mail software
such as [Outlook Express], etc. i [OK]
27
3. Printer
3 Printer
Printer
3.1 Printing from Windows
applications
You can print a file created in a Windows application. For
example, to print from WordPad, proceed as follows.
1 Open the document you want to print.
2 Select [Print...] from the [File] menu.
L The [Print] dialogue box will appear.
For details about the [Print] dialogue box, click
[?], then click the desired item.
and types of paper) on the unit before purchasing large
quantities.
You can change or display the settings on the following
tabs.
[Basic]: Paper size, media type, pages per sheet, etc.
[Output]: Number of prints, collate, etc.
[Quality]: Colour mode, colour management, toner
save feature, etc.
[Effects]: Watermark, overlay.
[Profile]: Saving the desired settings, selecting the
saved settings, etc.
[Support]: Version information.
Note:
L Select the desired media type on the [Basic] tab
according to the recording paper.
3 Select the unit’s name as the active printer.
L If you have changed the name of the unit when
installing, select that name from the list.
L For easier greyscale printing, select the unit’s
name with [B/W] attached to the name.
L To change the printer settings, proceed as
follows.
For Windows 98/Windows Me:
Click [Properties], then click the desired tab.
Change the printer settings, then click [OK].
For Windows 2000:
Click the desired tab and change the printer
settings.
For Windows XP/Windows Vista:
Click [Preferences], then click the desired tab.
Change the printer settings, then click [OK].
4 Click [Print] or [OK].
L The unit will start printing.
Note:
L To stop printing from the unit, see page 77.
L To load paper, see page 14, 29.
L For details about the paper specifications, see page
106.
L If a printing error occurs, the Device Monitor (page
76) will start automatically and display the error
information.
Setting the printer properties
You can change the printer setting in step 3. We
recommend that you test paper (especially special sizes
28
Recording paper type
Media type
Plain paper
75 g/m2 to 105 g/m2
(20 lb to 28 lb)
[Plain Paper]
Thin paper
60 g/m2 to 74 g/m2
(16 lb to 19 lb)
[Thin Paper]
Thick paper
106 g/m2 to 165 g/m2
(29 lb to 44 lb)
[Thick Paper]
Transparency
[Transparency]
Label
[Label]
Envelope*1
–––––––––
Card stock
163 g/m2 (90 lb)
[Card Stock]
*1 Select [Envelope #10] or [Envelope DL] for
paper size.
L When printing from a computer, the printer
properties setting overrides the following unit’s
programming features:
– Media type setting (feature #383 on page 59)
– Toner save setting (feature #482 on page 59)
L When printing on envelopes, press
{Black}/{Colour} of the unit after step 4. Change
the colour mode on the [Quality] tab beforehand.
3. Printer
3.1.1 Printing on special media
You can print not only on plain paper but also on special
media (transparencies / labels / envelopes / card stocks).
L Please refer to page 106 for information on recording
paper.
L To load paper, see page 14.
To print on transparencies
Use transparencies designed for laser printing.
We recommend the following:
3M® CG3300/PP2500
L Do not stack more than 25 transparencies at a
time.
L After printing, place transparencies on a flat
surface to cool and to prevent them from curling.
L Do not re-use transparencies that have already been
fed through the unit. This includes transparencies
that have been fed through and ejected without being
printed on.
L Some types of transparencies have instructions
recommending which side to print on. If the print
quality is poor, try printing on the other side of a new
transparency.
To print on labels
Use labels designed for laser printing. We recommend
the following:
Avery®
5160/5163/5660/5663/L7159/L7164
L Do not stack more than 25 labels at a time.
L Do not use the following types of labels:
– Labels that are wrinkled, damaged or separated
from the backing sheet.
– Any sheet of labels that has spaces in it where
some of the labels have been removed.
– Labels that do not completely cover the backing
sheet as follows.
To print on envelopes
Use envelopes designed for laser printing. We
recommend the following:
– High quality envelopes of 90 g/m2 (24 lb) paper,
– Envelopes that have thin, sharply creased leading
edges,
– Envelopes that have diagonal seams, and
– Envelopes with a moisture content of 4 % to 6 % by
weight.
L Load envelopes with the sealing flap FACE DOWN.
L Do not stack more than 10 envelopes at a time.
Note:
L Wrinkles and waving may occur in some cases, even
if high quality envelopes are used.
L Avoid printing in high humidity. High humidity may
cause the envelope to curl or seal the envelope.
L Store envelopes away from moisture and humidity,
where they can lay flat and their edges will not be
bent or damaged.
Do not use envelopes with any of the following
characteristics (using these may result in paper
jams):
L Irregularly shaped envelopes
L Envelopes with curls, wrinkles, nicks, twists, dogears or other damage
L Envelopes with side seam construction
L Highly textured envelopes, or envelopes with
extremely shiny surfaces
L Envelopes that seal by removing a peel-off strip
L Envelopes with more than one flap to be sealed
L Self-adhesive envelopes
L Envelopes that are baggy or not sharply creased
L Embossed envelopes
L Envelopes that have previously been printed on
L Envelopes that include cotton and/or fibre material
Side seam
construction
Peel-off strip
Multiple flaps
29
3. Printer
3.2 Printing a received e-mail
attachment automatically (LAN
connection only)
Twisted
Curled
Bent-edged
Waved
Dog-eared
Self adhesive
Do not attempt to print on any of the following types
of envelopes (these may cause damage to the unit):
L Envelopes with clasps, snaps or tie strings
L Envelopes with transparent windows
L Envelopes that use encapsulated types of adhesive
that do not require moistening but rely on pressure to
seal them
If you configure the POP server beforehand, the unit will
automatically print e-mail attached files sent from a
compatible unit via the internet (scan to e-mail print).
This is useful if you want to print only the attachment file,
without checking your e-mails.
Important:
L The unit does not print e-mail messages.
L The unit will only print attached files sent from a
compatible unit, which can send e-mails directly
(without using a computer).
L The attachment file formats that can be printed
are as follows.
– TIFF
– JPEG
– PDF (files scanned from the unit, or scanned
from the computer using Multi-Function
Viewer)
L Received e-mails and the attached files will be
deleted automatically after printing.
A
Clasp
B
C
Transparent window
3.1.2 Duplex printing (optional)
Connecting the optional automatic duplex unit allows
duplex printing (page 80). For example, to print from
WordPad, proceed as follows.
1 Open the document you want to print.
2 Select [Print...] from the [File] menu.
3 Select the unit’s name as the active printer.
L For Windows 2000 users, go to step 5.
4 For Windows 98/Windows Me:
[Properties]
For Windows XP/Windows Vista:
[Preferences]
5 Click the [Basic] tab.
6 Select the desired duplex layout. i [OK]
L Select [None] to deactivate this feature.
L You can also change the duplex margin.
7 Click [Print] or [OK].
Booklet feature
You can print the document, then fold in half to create
booklets. The documents will be reduced to fit the
recording paper.
To use this feature, select [Booklet] icon for print layout
after step 5.
30
A Send from a compatible multi-function unit (Example:
“4.1.5 Scan to e-mail server (LAN connection only)”,
page 33)
B Via the internet (e-mail server)
C The unit will print an attached file
1 Start Multi-Function Station.
2 [Utilities] i [Configuration Web Page] i
[Network Configuration]
3 Type “root” as the user name, then enter the
password (feature #155 on page 58). i [OK]
4 Click the [SCAN TO E-MAIL PRINT] tab.
5 Set each item.
To activate this feature:
Select [ENABLED] next to [SCAN TO E-MAIL
PRINT]. i [Submit]
To set the e-mail server information:
1. Click [Edit] next to [E-MAIL SERVER].
2. Enter the e-mail server and POP server
information. i [Submit]
6 Close the web browser.
3. Printer
Note:
L Printing will not stop even if you press {Stop}.
L This feature can be programmed only through the
web browser interface (page 56).
L To view the recent scan to e-mail print information,
click [List] next to [E-MAIL PRINT LOG] (page 74).
L If the attached file is too heavy or is a non-supporting
format, it will not be printed properly.
L You can change the e-mail checking interval (page
73) or header print setting (page 74).
L Consult your service provider or network
administrator for details.
31
4. Scanner
5 If necessary, change the scanning settings. Press
4 Scanner
Scanner
4.1 Scanning from the unit (Push
Scan)
You can easily scan the document by using the operation
panel on the unit. Select following scanning modes
depending on the way to use the scanned image.
– Viewing using Multi-Function Viewer (Viewer)
– Saving as a file to your computer (File)
– Sending as an attached file to e-mail destination from
your computer (E-mail)
– Using OCR software (OCR)
– Sending as an attached file to e-mail destination
directly from your server (E-mail server)
– Sending to an FTP server (FTP)
Note:
L You can set the desired scan mode for push scan
beforehand (feature #493 on page 69).
L To select the scan type for monochrome scanning
(black/white or greyscale), set the desired type
beforehand (feature #495 on page 69).
L The scanned image will be automatically saved in the
folder selected in the [Settings] window.
L When scanning a document, we recommend using
the scanner glass rather than the automatic
document feeder for better results.
L Do not open the document cover when scanning a
document with the automatic document feeder.
{>}, press {V} or {^} repeatedly to select the
desired setting. i {Set} i {Black}/{Colour}
L The scanned image will be displayed in the
[Multi-Function Viewer] window after
scanning. However, when you select PDF as a
file format, the software that is associated to
open PDF file will start.
Note:
L To stop scanning, see page 77.
L You can save the images in TIFF, JPEG, BMP or PDF
formats.
4.1.2 Scan to save as a file
1 Set the original (page 19).
2 {Scan}
3 Press {V} or {^} repeatedly to select “FILE”. i
{Set}
4 For USB connection:
Press {V} or {^} repeatedly to select “USB HOST”.
i {Set}
For LAN connection:
Press {V} or {^} repeatedly to select the computer to
which you want to send the scanned image. i
{Set}
5 If necessary, change the scanning settings. Press
{>}, press {V} or {^} repeatedly to select the
desired setting. i {Set} i {Black}/{Colour}
L The scanned image will be automatically saved
in the folder selected in the [Settings] window.
To change the folder, see page 27.
Station keys
{Scan}
Note:
L To stop scanning, see page 77.
L You can save the images in TIFF, JPEG, BMP or PDF
formats.
{Lower}
{Stop}
{Black} {Colour}
{Set}{V}{^}{>}
4.1.1 Scan to Multi-Function Viewer
1 Set the original (page 19).
2 {Scan}
3 Press {V} or {^} repeatedly to select “VIEWER”. i
{Set}
4 For USB connection:
Press {V} or {^} repeatedly to select “USB HOST”.
i {Set}
For LAN connection:
Press {V} or {^} repeatedly to select the computer to
which you want to send the scanned image. i
{Set}
32
4.1.3 Scan to E-mail
You can send the scanned image as an attachment to an
e-mail using e-mail software in your computer.
1 Set the original (page 19).
2 {Scan}
3 Press {V} or {^} repeatedly to select “E-MAIL”. i
{Set}
4 For USB connection:
Press {V} or {^} repeatedly to select “USB HOST”.
i {Set}
For LAN connection:
Press {V} or {^} repeatedly to select the computer to
which you want to send the scanned image. i
{Set}
5 If necessary, change the scanning settings. Press
{>}, press {V} or {^} repeatedly to select the
desired setting. i {Set} i {Black}/{Colour}
4. Scanner
L The e-mail software will automatically start and
the scanned image will be attached to a new email message.
Note:
L To select the default E-mail software, see page 27.
L To stop scanning, see page 77.
L You can save the images in TIFF, JPEG or PDF
formats.
4.1.4 Scan to OCR
With OCR software, you can convert an image into text
data that can be edited with word processing software.
Readiris OCR software can be installed when installing
Multi-Function Station.
1 Set the original (page 19).
2 {Scan}
3 Press {V} or {^} repeatedly to select “OCR”. i
{Set}
4 For USB connection:
Press {V} or {^} repeatedly to select the desired
destination.
Using dial keypad:
Press {Set}, then enter the e-mail address using the
dial keypad (page 75).
5 {Set}
6 If necessary, change the scanning settings. Press
{>}, press {V} or {^} repeatedly to select the
desired setting. i {Set} i {Black}/{Colour}
L The scanned image will be sent as an
attachment via e-mail server.
Note:
L You can search for an e-mail address by initial.
Example: “LISA”
1. Proceed steps 1 to 3 on “4.1.5 Scan to e-mail
server (LAN connection only)”, page 33.
2. Press {5} repeatedly to display any name with
the initial “L” (see page 75 for character entry).
L To search for symbols, press {*}.
Press {V} or {^} repeatedly to select “USB HOST”.
i {Set}
3. Press {V} or {^} repeatedly to display “LISA”.
L To stop the search, press {Stop}.
For LAN connection:
Press {V} or {^} repeatedly to select the computer to
which you want to send the scanned image. i
{Set}
L You can easily send scanned image to the desired
destinations using station keys. To use this feature,
register e-mail addresses to station keys beforehand
(page 70).
5 If necessary, change the scanning settings. Press
{>}, press {V} or {^} repeatedly to select the
desired setting. i {Set} i {Black}/{Colour}
L The scanned image will be displayed in the OCR
window after scanning.
Note:
L You can save the images in TIFF, JPEG or BMP
formats.
L For detailed instructions about OCR, select [Help].
4.1.5 Scan to e-mail server (LAN
connection only)
You can send the scanned image as an attachment
without using e-mail software. To select the e-mail
destination easily, register e-mail addresses through the
web browser interface beforehand (page 70).
Important:
L Program the e-mail server and SMTP server
settings beforehand (page 69).
1 Set the original (page 19).
2 {Scan}
3 Press {V} or {^} repeatedly to select “E-MAIL
SERVER”. i {Set}
4 Enter the destination e-mail address.
Using stations 1-3:
Press the desired station key.
Using stations 4-6:
Press {Lower}, then press the desired station key.
Using navigator key:
1. Set the original (page 19).
2. {Scan}
3. Using stations 1-3:
Press the desired station key.
Using stations 4-6:
Press {Lower}, then press the desired station
key.
4. {Set} i {Black}/{Colour}
L You can save the images in TIFF, JPEG or PDF
formats.
4.1.6 Scan to FTP server (LAN connection
only)
You can send the scanned image to a folder on an FTP
server.
Important:
L Program the FTP server settings beforehand
(page 70).
1 Set the original (page 19).
2 {Scan}
3 Press {V} or {^} repeatedly to select “FTP
SERVER”. i {Set}
4 Press {V} or {^} repeatedly to select the destination
to which you want to send the scanned image. i
{Set}
33
4. Scanner
5 If necessary, change the scanning settings. Press
{>}, press {V} or {^} repeatedly to select the
desired setting. i {Set} i {Black}/{Colour}
Note:
L You can save the images in TIFF, JPEG or PDF
formats.
4.2 Scanning from a computer
(Pull Scan)
Note:
L When scanning a document, we recommend using
the scanner glass rather than the automatic
document feeder for better results.
L Do not open the document cover when scanning a
document with the automatic document feeder.
4.2.1 Using Multi-Function scan
application
By clicking an application icon, the selected application
starts automatically after scanning.
1 Set the original (page 19).
2 Start Multi-Function Station. i [Scan]
3 Click the desired application icon.
L When you click [Custom], the pre-programmed
application starts.
L To cancel scanning while the documents is being
scanned, click [Cancel].
Note:
L You can change the scanning settings beforehand for
each application (page 27).
L By pointing to an application icon, scanning settings
are displayed as tooltip.
4.2.2 Using Multi-Function Viewer
1 Set the original (page 19).
2 Start Multi-Function Station.
3 [Utilities] i [Viewer]
L [Multi-Function Viewer] will appear.
4 Click the [Scan] icon in the [Multi-Function
Viewer] window.
L The unit’s name dialogue box will appear.
5 If necessary, change the scanning settings on your
computer.
L To preview the scanned image, click [Preview].
You can drag the frame to specify the scanned
area. If you change the scan settings, click
[Preview] to refresh the scanned image.
If you use the automatic document feeder, only
the first page will be previewed. When you need
to refresh the scanned image, set the document
to preview again.
6 [Scan]
L If you preview the scanned image using the
automatic document feeder in step 5, set the
document again and click [Scan].
L The scanned image will be displayed in the
[Multi-Function Viewer] window after
scanning.
34
4. Scanner
L To save the scanned image, select [Save As ...]
from the [File] menu.
L To cancel scanning while the document is being
scanned, click [Cancel].
Note:
L You can display images in applications that support
TIFF, JPEG, PCX, DCX and BMP formats.
L You can save images in TIFF, JPEG, PCX, DCX,
BMP or PDF formats.
L If the [Select...] button is displayed in the [Target
Device], click the [Select...] to select the unit from
the list, then click [OK].
The [Select...] button will not be displayed when
there is only one printer driver installed.
L You can move, copy and delete a file or page.
4.2.3 Using other applications
Multi-Function Station includes a TWAIN and WIA
compliant scanner driver. You can also scan using other
applications that support TWAIN or WIA scanning. For
scanning example, proceed as follows.
1 Set the original (page 19).
2 Start an application that supports TWAIN or WIA
scanning.
3 For TWAIN scanning:
Select [Acquire Image...] from the [File] menu.
For WIA scanning:
Select [From Scanner or Camera...] from the
[File] menu.
L The unit’s name dialogue box will appear.
4 If necessary, change the scanning settings on your
computer. i [Scan]
L The scanned image will be displayed in the
application window after scanning.
L To cancel scanning while the document is being
scanned, click [Cancel].
Note:
L Scanning from WIA compliant applications is only
available for Windows XP and Windows Vista, and
via a USB connection.
L Depending on the application used, the appearance
may differ slightly.
L If the [Select...] button is displayed in the [Target
Device] when performing TWAIN scanning, click the
[Select...] to select the unit from the list, then click
[OK].
The [Select...] button will not be displayed when
there is only one printer driver installed.
35
5. Copier
5 Copier
Copy
5.1 Making a copy
5.1.1 Using the scanner glass
{Copy}
Note:
L You can change the default resolution (feature #461
on page 65).
To select the contrast
You can adjust this setting depending on the darkness or
lightness of the document. 5 levels (low to high) are
available.
Press {Contrast} repeatedly. i {Set}
Note:
L You can hold the previous contrast setting (feature
#462 on page 65).
{Colour}
{Contrast}
{Resolution} {Black}
{Stop}
{Set}
{Fax Auto Answer}
1 If the {Copy} light is OFF, turn it ON by pressing
{Copy}.
2 Set the original (page 19).
3 If necessary, change the resolution and contrast
according to the type of document.
L To select the resolution, see page 36.
L To select the contrast, see page 36.
4 If necessary, enter the number of copies (up to 99).
5 {Black}/{Colour}
L The unit will start copying.
6 After you finish copying, press {Stop} to reset the
settings you set in step 3 and 4.
Note:
L To stop copying, see page 77.
L You can change the default operation mode (feature
#463 on page 59) and the timer before returning to
the default operation mode (feature #464 on page
59).
L If the {Fax Auto Answer} light is ON, the unit can
receive faxes automatically even when in the copy
mode.
To select the resolution
1. Press {Resolution} repeatedly.
– “TEXT/PHOTO”: For both text and photographs.
– “TEXT”: For text only.
– “PHOTO”: For photographs, shaded drawings,
etc.
2. {Set}
36
5. Copier
5.1.2 Using the automatic document feeder
5.2 More copying features
L Make sure that the {Copy} light is ON.
{Copy}
5.2.1 Zoom copy (enlargement / reduction)
1 Set the original (page 19).
2 Press {Zoom} repeatedly to select the zoom rate
{Stop}
{Black}
{Colour}
1 If the {Copy} light is OFF, turn it ON by pressing
{Copy}.
2 Set the original (page 20).
3 If necessary, change the resolution and contrast
according to the type of document.
L To select the resolution, see page 36.
L To select the contrast, see page 36.
4 If necessary, enter the number of copies (up to 99).
5 {Black}/{Colour}
L The unit will start copying.
6 After you finish copying, press {Stop} to reset the
settings you set in step 3 and 4.
Note:
L To stop copying, see page 77.
that fits the size of your document and recording
paper.
– “ZOOM =100%”*1
– “50%”
– “200%”
– “LTR>A4”*2
– “A4>LTR”*3
– “LGL>A4”*2
– “LGL>LTR”*3
*1 Press {V} or {^} repeatedly to change the zoom
rate by 1 % at a time from “25%” to “400%”.
You can also enter the desired percentage
specifically by using the dial keys.
*2 Make sure A4-size recording paper is installed.
*3 Make sure letter-size recording paper is
installed.
3 {Set}
4 If necessary, enter the number of copies (up to 99).
i {Black}/{Colour}
5 After you finish copying, press {Stop} to reset this
feature.
Note:
L Zoom copy is not available for the following features:
– Quick ID copy feature (page 39)
– Easy repeat feature (page 39)
– Poster feature (page 40)
– N in 1 feature (page 40)
– Separate N in 1 feature (page 41)
– Booklet feature (page 41)
L You can hold the previous zoom setting (feature #468
on page 65).
L When using the scanner glass, the unit will only
enlarge the right top corner of the document starting
from the m mark on the unit.
L When using the automatic document feeder, the
unit will only enlarge the centre of the upper part of
the document. To make an enlarged copy of the
bottom of the document, turn the document around,
and then make a copy.
37
5. Copier
documents are scanned, then press
{Black}/{Colour}.
L The unit will start copying.
Example: 150 % enlarged copy
Using the scanner glass (1):
Original document
Enlarged copy
When using the automatic document feeder:
{Black}/{Colour}
6 After you finish copying, press {Stop} to reset this
feature.
Example: Making 2 copies of a 4-page original
document
1
Using the automatic document feeder:
Original document
4
3
Enlarged copy
4
2
4
1
3
3
2
4
2
3
1
2
1
Example: 70 % reduced copy
Using the scanner glass (1):
Original document
Reduced copy
Using the automatic document feeder:
Reduced copy
5.2.2 Collate copy
The unit can collate multiple copies in the same order as
the original document pages.
1
2
3
4
5
Set the original (page 19).
Press {Collate} repeatedly to display “ON”.
{Set}
Enter the number of copies (up to 99).
When using the scanner glass:
1. {Black}/{Colour}
L The unit will scan 1 page.
2. Place the next document on the scanner glass
and press {Set}. Repeat this until all the
38
Uncollated pages
Note:
L The unit will store the documents into memory while
collating the copies. If memory becomes full while
storing, the unit will only print out the stored pages.
L You can hold the previous collate setting (feature
#469 on page 65).
1
Original document
Collated pages
1
Proof set feature
To make 1 set of collate copy first, press {Collate}
repeatedly to display “PROOF SET” (step 2 on
“5.2.2 Collate copy”, page 38). The unit will make 1 set of
collate copy and stop temporarily so you can check
whether the copy is made as you expected. If the copy is
correct, press {Black}/{Colour} to continue copying.
If the copy is not correct, press {Stop} and start again
from the beginning.
5. Copier
5.2.3 Quick ID copy feature / Easy repeat
feature (Scanner glass only)
Quick ID copy feature: To copy 2-sided documents
onto one page.
Easy repeat feature: To copy a single document
repeatedly onto one page.
For quick ID copy feature
Original document
Page layout
“2 in 1”
“LANDSCAPE”
Note:
L The copied documents will not be reduced to fit the
recording paper, and useful for copying small sized
documents such as business cards.
“PORTRAIT”
1 Set the original (page 19).
L To make a landscape copy, set the original in
landscape direction. To make a portrait copy, set
the original in portrait direction.
L The scanning area changes according to the
selected setting in step 4. See the following table
for details. The shaded area will be scanned.
“4 in 1”
“LANDSCAPE”
“PORTRAIT”
2 {Page Layout}
3 Press {V} or {^} repeatedly to select “QUIK ID
COPY” or “EASY REPEAT”. i {Set}
4 Press {V} or {^} repeatedly to select the number of
original documents from “2 in 1”, “4 in 1” or “8
in 1”. i {Set}
L For quick ID copy feature, go to the next step.
L For easy repeat feature, skip to step 6.
“8 in 1”
“LANDSCAPE”
5 Press {V} or {^} repeatedly to select the page layout
from “LANDSCAPE” or “PORTRAIT”. i {Set}
6 If necessary, enter the number of copies (up to 99).
7 Quick ID copy feature:
“PORTRAIT”
1. {Black}/{Colour}
L The unit will scan 1 page.
2. Place the next document on the scanner glass
and press {Set}. Repeat this until all the
documents are scanned.
L The unit will start copying.
L You can press {Black}/{Colour} anytime to
start copying.
For easy repeat feature
Original document
Page layout
“2 in 1”
Easy repeat feature:
{Black}/{Colour}
8 After you finish copying, press {Stop} to reset this
feature.
39
5. Copier
Original document
Page layout
“4 in 1”
Note:
L You can save the previous page layout setting
(feature #467 on page 65).
5.2.5 N in 1 feature
You can save paper by copying 2, 4 or 8 pages onto 1
page. The documents will be reduced to fit the recording
paper.
1 Set the original (page 19).
“8 in 1”
L To make a portrait copy, set the original in portrait
direction. To make a landscape copy, set the
original in landscape direction.
2 {Page Layout}
3 Press {V} or {^} repeatedly to select “N in 1”. i
{Set}
4 Press {V} or {^} repeatedly to select the number of
original documents from “2 in 1”, “4 in 1” or “8
in 1”. i {Set}
5 Press {V} or {^} repeatedly to select the layout from
“PORTRAIT” or “LANDSCAPE”. i {Set}
Note:
L You can save the previous page layout setting
(feature #467 on page 65).
5.2.4 Poster feature (Scanner glass only)
You can make copies divided into 4 (“2 × 2”) or 9 (“3 ×
3”) sections to make enlarged copies of the individual
sections. You can then glue them together to make a
poster.
6 If necessary, enter the number of copies (up to 99).
7 When using the scanner glass:
1. {Black}/{Colour}
L The unit will scan 1 page.
2. Place the next document on the scanner glass
and press {Set}. Repeat this until all the
documents are scanned.
L The unit will start copying.
L You can press {Black}/{Colour} anytime to
start copying.
When using the automatic document feeder:
{Black}/{Colour}
8 After you finish copying, press {Stop} to reset this
feature.
Original document
Page layout
“2 in 1”
“PORTRAIT”
“LANDSCAPE”
1 Set the original (page 19).
2 {Page Layout}
3 Press {V} or {^} repeatedly to select “POSTER”. i
“4 in 1”
“PORTRAIT”
{Set}
4 Press {V} or {^} repeatedly to select “2 × 2” or “3
× 3”. i {Set}
5 If necessary, enter the number of copies (up to 99).
i {Black}/{Colour}
6 After you finish copying, press {Stop} to reset this
feature.
40
“LANDSCAPE”
5. Copier
Original document
Page layout
“8 in 1”
“PORTRAIT”
1
2
3
4
Set the original (page 19).
{Page Layout}
Press {<} or {>} repeatedly to select “DUPLEX”.
Press {V} or {^} repeatedly to select the desired
binding.
– “LONG EDGE”
“LANDSCAPE”
–
“SHORT EDGE”
Note:
L You can save the previous page layout setting
(feature #467 on page 65).
Separate N in 1 feature (Scanner glass only)
You can separate an N in 1 copied document back into
its original, separate pages. This feature is available
from “2 in 1” and “4 in 1” copy.
1. Set the original (page 19).
2. {Page Layout}
3. Press {V} or {^} repeatedly to select “SEPARATE N
in 1”. i {Set}
4. Press {V} or {^} repeatedly to select the number of
original documents from “2 in 1” or “4 in 1”. i
{Set}
5. Press {V} or {^} repeatedly to select the page layout
of the original document from “PORTRAIT” or
“LANDSCAPE”. i {Set}
6. If necessary, enter the number of documents (up to
99). i {Black}/{Colour}
7. After you finish copying, press {Stop} to reset this
feature.
5.2.6 Copy reservation
You can reserve your copy;
– while the unit is printing documents from your
computer.
– while the unit is printing received fax documents.
1 Set the original (page 19).
2 While “PC PRINTING” or “PRINTING” is displayed,
press {Copy}.
3 Make necessary settings such as number of copies,
resolution, zoom features and page layout features.
i {Black}/{Colour}
L “COPY RESERVED” will be displayed. The unit
will start copying after the current printing job.
5.2.7 Duplex copy (optional)
Connecting the optional automatic duplex unit allows
duplex copy (page 80). You can make 2-sided copies of
1-sided documents.
L Select “OFF” to deactivate this feature.
5 {Set}
6 If necessary, enter the number of documents (up to
99).
7 When using the scanner glass:
1. {Black}/{Colour}
L The unit will scan 1 page.
2. Place the next document on the scanner glass
and press {Set}.
L The unit will start copying.
When using the automatic document feeder:
{Black}/{Colour}
8 After you finish copying, press {Stop} to reset this
feature.
Note:
L Duplex copy is not available for quick ID copy feature
(page 39), easy repeat feature (page 39) or poster
feature (page 40).
L You can save the previous duplex setting (feature
#470 on page 65).
Booklet feature
You can make copies, and then fold them in half to create
booklets. The documents will be reduced to fit the
recording paper.
1. Set the original (page 19).
2. {Page Layout}
3. Press {V} or {^} repeatedly to select “BOOKLET”.
i {Set}
4. Press {V} or {^} repeatedly to select the desired
binding direction from “LEFT BIND” or “RIGHT
BIND”. i {Set}
5. Press {V} or {^} repeatedly to select the desired
binding pages.
– “1”: To print 4 documents as separate blocks.
41
5. Copier
–
“ALL”: To print all documents as 1 block
(monochrome printing only).
6. {Set}
7. If necessary, enter the number of documents (up to
99).
L Multiple copies will be collated automatically.
8. When using the scanner glass:
1. {Black}/{Colour}
L The unit will scan 1 page.
2. Place the next document on the scanner glass
and press {Set}. Repeat this until all the
documents are scanned.
3. If “1” is selected in step 5, the unit will start
copying.
L You can press {Black}/{Colour} anytime to
start copying.
L For multiple copies, press {Black}/{Colour}
to start copying.
If “ALL” is selected in step 5, press {Black} to
start copying.
When using the automatic document feeder:
{Black}/{Colour}
9. After you finish copying, press {Stop} to reset this
feature.
Note:
L If “ALL” is selected in step 5, only monochrome copy
is available, so press {Black} in step 8. If you press
{Colour}, steps 2 to 7 will be reset.
L You can save the previous page layout setting
(feature #467 on page 65).
42
6. Fax
6 Fax
Sending
Faxes
6.1 Sending a fax manually
Important:
L You can only send faxes in monochrome.
6.1.1 Using the scanner glass
By using the scanner glass, you can send a page from
booklets or small size paper that cannot be sent with the
automatic document feeder.
–
–
–
“FINE”: For small-sized characters.
“SUPER FINE”: For very small-sized characters.
“PHOTO”: For photographs, shaded drawings,
etc.
2. {Set}
L Using the “FINE”, “SUPER FINE” and “PHOTO”
settings will increase transmission time.
To select the contrast
You can adjust this setting depending on the darkness or
lightness of the document. 5 levels (low to high) are
available.
Press {Contrast} repeatedly. i {Set}
{Fax}
To redial the last number
{Redial}
L If the line is busy, the unit will automatically redial the
number 1 time.
Note:
L To stop sending, see page 77.
{Contrast}
{Black} {Redial}
{Resolution} {Set}
{Quick Scan}
1 If the {Fax} light is OFF, turn it ON by pressing
{Fax}.
2 Set the original (page 19).
3 If necessary, change the resolution and contrast
according to the type of document.
L To select the resolution, see page 43.
L To select the contrast, see page 43.
4 Dial the fax number.
L To send a single page, skip to step 7.
L To send multiple pages, go to the next step.
5 Press {Quick Scan} to scan the document into
memory.
L Wait until “SCAN:PRESS SET” “SEND:PRESS
START” is displayed.
6 Place the next page on the scanner glass. i {Set}
L To send more pages, repeat this step.
7 {Black}
Note:
L To stop sending, see page 77.
L You can change the default operation mode (feature
#463 on page 59) and the timer before returning to
the default operation mode (feature #464 on page
59).
To select the resolution
Reserving the fax transmission (Dual Access)
You can reserve the fax transmission even when the unit
is just receiving a fax or sending a fax from memory.
– Up to 3 reservations when sending
– Up to 4 reservations when receiving
1. Set the original during fax reception or fax memory
transmission.
2. Enter the fax number using the dial keypad, onetouch dial or navigator directory.
3. When using the scanner glass, press {Quick
Scan}. The unit will scan 1 page. Place the next
document on the scanner glass and press {Set}.
Repeat this until all the documents are scanned, then
press {Black}.
When using the automatic document feeder,
press {Black}.
L If the document exceeds the memory capacity,
transmission will be cancelled. You must send the
entire document manually.
Printing a confirmation report
A confirmation report provides you with a printed record
of transmission results. To print confirmation reports,
make sure feature #401 is activated (page 61). For an
explanation of error messages, see page 82.
Printing a journal report
A journal report provides you with a printed record of the
30 most recent faxes. To print it manually, see page 104.
To print it automatically after every 30 new fax
transmissions and receptions, make sure feature #402 is
activated (page 61). For an explanation of error
messages, see page 82.
1. Press {Resolution} repeatedly.
– “STANDARD”: For normal-sized characters.
43
6. Fax
6.1.2 Using the automatic document feeder
{Fax}
6.2 Storing items for the onetouch dial feature and navigator
directory
The unit provides the one-touch dial feature (6 items)
and navigator directory (300 items).
L Station 1 and 2 can be used alternatively as
broadcast keys (page 46).
L Make sure that the {Fax} light is ON.
{Monitor}
{Quick Scan}
{Black}
{Directory}
{Menu}
{Stop}
1 If the {Fax} light is OFF, turn it ON by pressing
{Fax}.
2 Set the original (page 20).
3 If necessary, change the resolution and contrast
according to the type of document.
L To select the resolution, see page 43.
L To select the contrast, see page 43.
4 {Monitor}
5 Dial the fax number. i {Black}
Note:
L To stop sending, see page 77.
L Do not open the document cover when sending a fax
with the automatic document feeder.
{Fax}
{Set} {V}{^}{>}
Station keys {Lower}
6.2.1 Storing one-touch dial item
1 Press {Menu} repeatedly to display “DIRECTORY
SET”.
2 Select the desired station key.
For stations 1–2:
1. Press one of the station keys.
Pre-dialing a fax number
Example:
1. Enter the fax number.
2. Set the original (page 20). i {Black}
2. {Set}
Sending from memory (Quick scan feature)
For station 3:
1. Set the original (page 20).
Press the station key.
2. Enter the fax number. i {Quick Scan}
For stations 4–6:
STATION 1
DIAL MODE
[V^]
Press {Lower}, then press one of the station keys.
3 Enter the name, up to 16 characters (see page 75 for
character entry). i {Set}
4 Enter the telephone number, up to 32 digits. i
{Set}
L To program other items, repeat steps 2 to 4.
5 {Stop}
Note:
L A hyphen or a space entered in a telephone number
counts as 2 digits.
6.2.2 Storing navigator directory items
1 Press {Menu} repeatedly to display “DIRECTORY
SET”. i {>}
2 Enter the name, up to 16 characters (see page 75 for
character entry). i {Set}
44
6. Fax
3 Enter the telephone number, up to 32 digits. i
{Set}
L To program other items, repeat steps 2 to 3.
4 {Menu}
Note:
L A hyphen or a space entered in a telephone number
counts as 2 digits.
6.2.3 Editing a stored item
1 {Directory}
2 Press {V} or {^} repeatedly to display the desired
item. i {Menu} i {*}
3 Edit the name if necessary. i {Set}
4 Edit the telephone number if necessary. i {Set}
6.3 Sending a fax using onetouch dial feature and navigator
directory
Before using this feature, store the desired names and
telephone numbers into one-touch dial feature and
navigator directory (page 44).
L Make sure that the {Fax} light is ON.
6.3.1 Using the scanner glass
1 Set the original (page 19).
2 If necessary, change to the desired resolution (page
43) and the desired contrast (page 43).
3 Enter the fax number.
6.2.4 Erasing a stored item
Using stations 1–3:
1 {Directory}
2 Press {V} or {^} repeatedly to display the desired
Press the desired station key.
item. i {Menu} i {#}
L To cancel erasing, press {Stop}.
3 {Set}
Using stations 4–6:
Press {Lower}, then press the desired station key.
Using navigator directory:
Press {Directory}, then press {V} or {^} repeatedly
to display the desired item.
L To send a single page, skip to step 6.
L To send multiple pages, go to the next step.
4 Press {Quick Scan} to scan the document into
memory.
5 Place the next page. i {Set}
L To send more pages, repeat this step.
6 {Black}
To search for a name by initial
Example: “LISA”
1. {Directory}
2. Press {V} or {^} to initiate the navigator directory.
3. Press {5} repeatedly to display any name with the
initial “L” (see page 75 for character entry).
L To search for symbols, press {*}.
4. Press {V} or {^} repeatedly to display “LISA”.
L To stop the search, press {Stop}.
Fax auto redial
If the line is busy or if there is no answer, the unit will
automatically redial the number 1 time.
Note:
L To stop sending, see page 77.
6.3.2 Using the automatic document feeder
1 Set the original (page 20).
2 If necessary, change to the desired resolution (page
43) and the desired contrast (page 43).
45
6. Fax
3 Enter the fax number using one-touch dial or
navigator directory.
4 {Black}
6.4 Broadcast transmission
You can send the same document to multiple parties (up
to 20). To use this feature, store the fax numbers into
broadcast memory as follows.
Broadcast: Store items using one-touch dial or
navigator directory (page 44).
Manual broadcast: Store items using one-touch dial or
navigator directory (page 44). You can also use the dial
keypad to store items manually.
Your programmed items will remain in the broadcast
memory, allowing frequent re-use.
L The broadcast function utilizes stations 1–2. The
one-touch dial function will be cancelled.
L Make sure that the {Fax} light is ON.
6.4.1 Programming items into the
broadcast memory
1 Press {Menu} repeatedly to display “DIRECTORY
SET”.
2 Select the desired broadcast key.
For BROADCAST:
1. {Broadcast}
2. Press {V} or {^} repeatedly to select
“BROADCAST”.
For MANUAL BROADCAST:
1. {Manual Broad}
2. Press {V} or {^} repeatedly to select “MANUAL
BROAD”.
3 {Set}
4 Program items.
Using stations 1–3:
Press the desired station key.
Using stations 4–6:
Press {Lower}, then press the desired station key.
Using navigator directory:
Press {V} or {^} repeatedly to display the desired
item. i {Set}
Using the dial keypad (only for manual broad):
Enter the fax number. i {Set}
L The number in brackets indicates the number of
registered items.
L To program other items, repeat this step (up to 20
items).
L If you have programmed the wrong item, press
{Stop} to erase the item.
5 {Set}
L To program another broadcast key, repeat steps
2 to 5.
6 {Stop}
46
6. Fax
6.4.2 Adding a new item into the broadcast
memory
1 {Directory}
2 Press {V} or {^} repeatedly to display the desired
broadcast memory (“<BROADCAST>” or “<MANUAL
BROAD>”). i {Menu} i {*}
To send the same document using the automatic
document feeder
1. Set the original (page 20).
2. If necessary, change to the desired resolution (page
43) and the desired contrast (page 43).
3. Press {Broadcast} or {Manual Broad}.
3 Press {V} or {^} repeatedly to display the desired
item you want to add. i {Set}
L To add other items, repeat this step (up to 20
items).
4 {Stop}
Note:
L When adding new items to the MANUAL
BROADCAST memory, you can only select stored
items.
6.4.3 Erasing a stored item from the
broadcast memory
1 {Directory}
2 Press {V} or {^} repeatedly to display the desired
broadcast memory (“<BROADCAST>” or “<MANUAL
BROAD>”). i {Menu} i {#}
3 Press {V} or {^} repeatedly to display the desired
item you want to erase.
L To cancel erasing, press {Stop}.
4 {Set} i {Set} i {Stop}
6.4.4 Sending the same document to preprogrammed parties
To send the same document using the scanner glass
1. Set the original (page 19).
2. If necessary, change to the desired resolution (page
43) and the desired contrast (page 43).
3. Press {Broadcast} or {Manual Broad}.
L To send a single page, skip to step 5.
L To send multiple pages, go to the next step.
4. Place the next page. i {Set}
L To send more pages, repeat this step.
5. {Black}
Note:
L To stop sending, see page 77.
L If you select “FINE”, “SUPER FINE” or “PHOTO”
resolution, the number of pages that the unit can
send will decrease.
L If the document exceeds the memory capacity,
sending will be cancelled.
L If a party is busy or does not answer, it will be skipped
and redialed later 1 time.
L After transmission, the unit will automatically print a
report (broadcast sending report).
47
6. Fax
Receiving Faxes
6.5 Sending a computer
document as a fax message from
your computer
You can access the fax function from a Windows
application using Multi-Function Station.
For example, to send a document created from
WordPad, proceed as follows.
1 Open the document you want to send.
2 Select [Print...] from the [File] menu.
L The [Print] dialogue box will appear.
3 Select the PCFAX unit’s name as the active printer.
4 Click [Print] or [OK].
6.6 Receiving a fax automatically
– Auto answer ON
Important:
L You can only receive faxes in monochrome.
6.6.1 Activating FAX ONLY mode
Press {Fax Auto Answer} repeatedly to display “FAX
ONLY MODE”.
L The display will show the ring count in FAX ONLY
mode. If you wish to change it, press {V} or {^}
repeatedly to display the desired setting, and press
{Set}.
L The {Fax Auto Answer} light turns ON.
L The [Send a Fax] dialogue box will appear.
{Set}{V}{^}
How faxes are received
When receiving calls, the unit will automatically answer
all calls and only receive fax documents.
5 Enter the fax number using the keypad display or the
directory.
L To stop the operation, click [Cancel].
Note:
L The number of rings before a call is answered in FAX
ONLY mode can be changed (feature #210 on page
58).
6 [Send]
L The document will be sent through the unit from
your computer.
Note:
L To stop sending, see page 77.
L If the document exceeds the memory capacity of the
unit, sending will be cancelled.
L For details, see the help file by selecting [p] from
Multi-Function Station.
L Click [Select...] to change the active unit.
48
If you have subscribed to a Distinctive Ring service
See page 55.
6. Fax
6.7 Receiving a fax manually –
Auto answer OFF
Important:
L Use this mode with an extension telephone or the
optional handset unit.
L You can only receive faxes in monochrome.
–
–
–
document reception is required,
a fax calling tone (slow beep) is heard, or
no sound is heard,
press {Black}.
3. Replace the handset.
Note:
L To stop receiving, see page 77.
6.7.1 Activating TEL mode
Set the unit to TEL mode by pressing {Fax Auto
Answer} repeatedly to display “TEL MODE”.
L The {Fax Auto Answer} light turns OFF.
{Black}
Note:
L If you do not answer the call within 10 rings, the unit
will temporarily switch to fax reception. The other
party can then send a fax.
How to receive faxes with an extension telephone
If you have another telephone connected to the [EXT]
jack or the same line (extension telephone), you can use
the extension telephone to receive faxes.
1. When the extension telephone rings, lift the handset
of the extension telephone.
2. When:
– document reception is required,
– a fax calling tone (slow beep) is heard, or
– no sound is heard,
press {*} {#} {9} (default fax activation code)
firmly.
3. Replace the handset.
Note:
L To stop receiving, see page 77.
L To receive fax documents using the extension
telephone, make sure remote fax activation is turned
ON (feature #434 on page 63) beforehand. The
default setting is OFF.
How to receive faxes with the optional handset unit
1. Lift the handset to answer the call.
2. When:
49
6. Fax
6.8 Using the unit with an
answering machine
6.8.1 Setting up the unit and an answering
machine
1 Connect the answering machine (1).
L Answering machine is not supplied.
L Remove the stopper (2) if attached.
2
If a fax calling tone is detected, the fax machine will
receive a fax automatically.
L Regarding the remote access code for the answering
machine, see the operating instructions of the
answering machine.
Receiving a voice message and fax document in one
call
The caller can leave a voice message and send a fax
document during the same call. Inform the caller of the
following procedure beforehand.
1. The caller calls your unit.
L The answering device will answer the call.
2. The caller can leave a message after the greeting
message.
3. The caller presses {*}{#}{9} (pre-selected fax
activation code).
L The unit will activate the fax function.
4. The caller presses the start button to send a
document.
Note:
L To use this feature, make sure remote fax activation
is turned ON (feature #434 on page 63). The fax
activation code can also be changed.
L If there is no room left in the memory of your
answering machine, the unit may not be able to
receive documents. See the operating instructions of
the answering machine and erase unnecessary
messages.
1
2 Set the number of rings on the answering machine to
4 rings or less.
L This will allow the answering machine to answer
the call first.
3 Record a greeting message on the answering
machine.
L We recommend you record a message up to 10
seconds long, and not to pause for more than 4
seconds during the message. Otherwise, both
machines will not function correctly.
4 Activate the answering machine.
5 Set the unit to the desired receiving mode (page 48).
L If you set to FAX ONLY mode, change the ring
setting in FAX ONLY mode to “5 EXT. TAM”
(feature #210 on page 58).
6 Make sure each of the following are unique:
–
–
–
the remote access code of the answering
machine
the fax activation code (feature #434 on page 63)
remote access to your phone company’s Voice
Mail (if you subscribed)
Note:
L If the call is a phone call, the answering machine will
record voice messages.
50
6. Fax
6.9 Junk fax prohibitor
(preventing fax reception from
undesired callers)
If you subscribe to Call Display service (page 53), this
feature prevents fax reception from calls that do not
show caller information.
Additionally, the unit will not accept faxes originating
from numbers that match the ones on a programmable
junk fax prohibitor list.
Important:
L This feature does not work when manual
reception is performed.
2. Press {>} repeatedly to display “JUNK LIST
DISP.”. i {Set}
3. Press {V} or {^} repeatedly to display the desired
item. i {<}
L To cancel erasing, press {Stop}, then press
{Menu}.
4. {Set} i {Menu}
6.9.1 Activating the junk fax prohibitor
1 Press {Menu} repeatedly to display “JUNK FAX
PROH.”. i {>}
2 Press {V} or {^} repeatedly to select “ON”. i
{Set}
3 Press {Stop} to exit.
6.9.2 Storing undesired callers
You can register up to 20 undesired numbers from the
caller’s list (page 53) if you do not wish to receive faxes
from them.
1 Press {Menu} repeatedly to display “JUNK FAX
PROH.”.
2 Press {>} repeatedly to display “JUNK LIST SET”.
i {Set}
3 Press {V} or {^} repeatedly to display the party you
wish to prevent fax reception from. i {Set}
4 Press {Stop} 2 times to exit.
To display the junk fax prohibitor list
1. Press {Menu} repeatedly to display “JUNK FAX
PROH.”.
2. Press {>} repeatedly to display “JUNK LIST
DISP.”. i {Set}
3. Press {V} or {^} to display the items on the list.
4. Press {Stop} to exit.
To print the junk fax prohibitor list
1. Press {Menu} repeatedly to display “JUNK FAX
PROH.”.
2. Press {>} repeatedly to display “JUNK LIST
PRINT”. i {Set}
3. Press {Stop} to exit.
To erase an item from the junk fax prohibitor list
1. Press {Menu} repeatedly to display “JUNK FAX
PROH.”.
51
6. Fax
6.10 Receiving a fax on your
computer
You can receive a fax document on your computer. The
received fax document is saved as an image file (TIFFG4 format).
To receive a fax document using your computer, make
sure the following features are set beforehand.
– PC fax reception (feature #442 on page 64)
– Computer setting for the PC fax reception (feature
#443 on page 24)
1 Press {Fax Auto Answer} repeatedly to turn the
auto answer setting ON (page 48).
2 Start Multi-Function Station. i [PC FAX]
3 When a fax call is received, your computer will
receive a document through the unit.
Note:
L You can view, print or transfer the received document
using your computer.
Viewing a received document
1. Select [PC FAX] from Multi-Function Station.
2. Select [Received Log] in [Communication Log].
3. Click the item you want to view.
4. Click [File] in the menu bar, then select [View], or
click [View] icon in the toolbar.
L The received fax will be displayed.
If the unit’s memory stores a received fax document
You can load the document into your computer.
1. Select [PC FAX] from Multi-Function Station.
2. Select [Received Log] in [Communication Log].
3. Click [File] in the menu bar. i [Receive a Fax]
L If feature #442 is activated, the received fax
document will be automatically transferred to the
computer.
52
7. Call Display
7 Call
Call
Display
Display
7.1 Call Display service
This unit is compatible with the Call Display service
offered by your local telephone company. To use this
unit’s Call Display features, you must subscribe to a
Call Display service.
Make sure the following ring count is set to 2 or more
rings beforehand.
–
FAX ring count (feature #210 on page 58)
L The name display service may not be available in
some areas. For further information, please contact
your telephone company.
7.1.1 How Call Display is displayed
The calling party’s name or telephone number will be
displayed after the 1st ring. You have the option of
whether or not to answer the call.
The unit will automatically store caller information
(name, telephone number and date and time of the call)
from the 30 most recent calls. It is possible to view caller
information one at a time on the display (page 53) or
print the entire caller’s list (page 104).
L When caller information is received and it matches a
telephone number stored in the unit’s one-touch dial
or navigator directory, the stored name will be
displayed.
L If the unit is connected to a PBX (Private Branch
Exchange) system, caller information may not be
received properly. Consult your PBX supplier.
L If the unit cannot receive caller information, the
following will be displayed:
“UNAVAIL NAME&NO”: The caller dialed from an
area which does not provide Call Display service.
“PRIVATE CALLER”: The caller requested not to
send caller information.
“LONG DISTANCE”: The caller made a long distance
call.
To confirm caller information by printing the caller’s
list
– To print manually, see page 104.
– To print automatically after every 30 new calls,
activate feature #216 (page 58).
7.2 Viewing and calling back
using caller information
1 If the {Fax} light is OFF, turn it ON by pressing
{Fax}. i {Call Display}
2 Press {V} to search from the recently received caller
information.
L If you press {^}, the display order will be
reversed.
L To send a fax, see page 43.
3 Press {Monitor} to return the call.
L To make a phone call, lift the handset of the
optional handset unit.
To change the way caller information is displayed
Press {Call Display} repeatedly after step 2 to change
name/telephone number information.
7.2.1 Symbols and operations for caller
information
What “,” means
“,” on the display means the call has already been
viewed or answered.
To stop viewing
Press {Stop}.
To edit a telephone number before calling
back/storing
While displaying a desired caller information, press {*}
repeatedly. Each time you press {*}, the telephone
number will be changed as follows:
A 1 – Area code – Local telephone number (“1” added)
B Local telephone number only (area code omitted)
C Area code – Local telephone number
D 1 – Local telephone number (“1” added and area code
omitted)
L To store the number in one-touch dial or navigator
directory, follow from step 3 of the storing procedure
on page 54.
53
7. Call Display
7.3 Erasing caller information
7.4 Storing caller information
7.3.1 Erasing all caller information
7.4.1 Storing in the one-touch dial feature
and navigator directory
1 Press {Menu} repeatedly to display “CALLER
SETUP”. i {Set}
L “CALL LIST ERASE” will be displayed.
2 {Set}
L To cancel erasing, press {Stop}, then {Menu}.
3 {Set} i {Stop}
7.3.2 Erasing specific caller information
L Make sure that the {Fax} light is ON.
1 {Call Display}
2 Press {V} or {^} repeatedly to display the desired
item. i {<} i {Set} i {Stop}
L Make sure that the {Fax} light is ON.
1 {Call Display}
2 Press {V} or {^} repeatedly to display the desired
item.
3 {Menu}
4 Select the station key or navigator directory.
For stations 1–2:
1. Press the desired station key.
2. Press {V} or {^} repeatedly to select “DIAL
MODE”. i {Set} i {Set}
For station 3:
Press the station key. i {Set}
For stations 4–6:
Press {Lower}, then press the desired station key.
i {Set}
For navigator directory:
Press {<} or {>}. i {Set}
5 {Set}
Note:
L To edit a name or number, see page 45.
L If you assign an item to a station key which already
contains an item, the previous item will be replaced.
L Station 1 and 2 can be used alternatively as
broadcast keys (page 46).
54
8. Distinctive Ring
8 Distinctive
Distinctive
Ring
Ring
8.1 Distinctive Ring service
When a call is made to one of your phone numbers, the
telephone company sends a ring pattern to your
telephone line to indicate which number the call is
intended for. By setting up this unit for Distinctive Ring,
you can make the unit automatically start fax reception
when a call comes to the fax number.
To use this service, you must subscribe to the
Distinctive Ring service offered by your local
telephone company. Consult your local telephone
company for availability.
8.2 Using two or more phone
numbers on a single telephone
line
8.2.1 Activating the Distinctive Ring
feature
To use one phone number for the fax, program the ring
pattern assigned for the fax (feature #431 on page 55). In
the example, the ring pattern assigned for fax is a triple
ring, so you should program “C” (triple ring).
Ring pattern
Selection
Standard ring (one long ring)
{1} “A”
1st ring
2nd ring
Double ring (two short rings)
1st ring
2nd ring
Triple ring (short-long-short
rings)
1st ring
{3} “C”
2nd ring
Other triple ring (short-short-long
rings)
1 {Menu} i {#}{4}{3}{0}
2 Press {1} to select “ON”.
{2} “B”
{4} “D”
L Press {0} to select “OFF”.
3 {Set} i {Menu}
1st ring
Note:
L While the Distinctive Ring feature is activated, you
cannot change the receiving mode.
How phone calls and faxes are received
If the incoming call is for the fax number, the unit will ring
with the assigned ring pattern and automatically start fax
reception.
If the incoming call is for the phone number, the unit will
keep on ringing.
L If an external telephone answering machine is
connected, set the ring count of the answering
machine to more than 2.
2nd ring
Note:
L The default setting is {5} “B-D”. The fax will respond
to all calls with ring tone patterns “B”, “C” and “D”.
8.4 Programming the ring pattern
assigned for fax
1 Set feature #430 to “ON” (page 55).
2 {Menu} i {#}{4}{3}{1}
3 Press {1} to {5} to select the ring pattern assigned
for fax. i {Set} i {Menu}
8.3 Using three or more phone
numbers on a single telephone
line
You may wish to use three or more phone numbers for a
single telephone line. In order to distinguish which
number the call was addressed to, a different ring
pattern must be assigned for each number.
Example: Using three phone numbers
Telephone
number
Ring pattern
Use
012 1234
Standard ring
Personal
012 5678
Double ring
Business
012 9876
Triple ring
Fax
55
9. Programmable Features
9 Programmable
Features
Summary
Features
9.1 Programming
{Menu}
{Set}
1 {Menu}
2 Press {#} and the 3-digit code (page 57 to page
72).
3 Press the desired selection to display the desired
setting.
L This step may be slightly different depending on
the feature.
4 {Set}
5 Press {Menu} to exit.
To select features through the web browser interface
(LAN connection only)
You can change features through the web browser
interface instead of the unit.
1. Start Multi-Function Station. i [Utilities] i
[Configuration Web Page]
L You can also access the unit by entering its IP
address on the web browser.
2. Select the desired category from the menu bar.
[Device Configuration]: features of the unit
[Network Configuration]: features of the network
3. Type “root” as the user name, then enter the
password (feature #155 on page 58). i [OK]
4. Select the desired feature tab at the top of the right
frame.
5. Change the settings or edit information.
L This step may be slightly different depending on
the feature.
6. [Submit]
L The new data will be transferred to the unit.
7. Close the web browser.
Note:
L The settings displayed in the web browser will be
updated by clicking [Reload].
56
9. Programmable Features
9.2 Basic features
Feature/Code
Selection
Setting the quick setup
{#}{1}{0}{0}
You can print out the quick fax setup guide and select the desired receiving
mode depending on your situation.
{1} “FAX ONLY” (default): Use only as a fax (page 48).
{2} “DIST. RING”: With the Distinctive Ring service (page 55).
{3} “EXT. TAM”: With an external telephone answering machine (page 50).
{4} “TEL ONLY”: Mostly phone calls (page 49).
1. {Menu} i {#}{1}{0}{0}
2. {Set}
3. Press {Set} again to print the quick fax setup guide.
L If you do not wish to print it, press {Stop}.
4. Press {1} to {4} to display the desired setting.
5. {Set} i {Menu}
Setting the date and time
{#}{1}{0}{1}
Enter the date and time using the dial keypad. See page 22 for details.
Setting your logo
{#}{1}{0}{2}
Enter your logo using the dial keypad. See page 22 for details.
Setting your fax number
{#}{1}{0}{3}
Enter your fax number using the dial keypad. See page 23 for details.
Selecting the language
{#}{1}{1}{0}
The display and reports will be in the selected language.
{1} “ENGLISH” (default): English is used.
{2} “FRENCH”: French is used.
1. {Menu} i {#}{1}{1}{0}
2. Press {1} or {2} to select the desired language. i {Set} i {Menu}
Setting the dialing mode
{#}{1}{2}{0}
{1} “PULSE”
{2} “TONE” (default)
See page 18 for details.
Setting flash time
{#}{1}{2}{1}
The flash time depends on your telephone exchange or host PBX.
{0} “900ms”
{1} “700ms” (default)
{2} “600ms”
{3} “400ms”
{4} “300ms”
{5} “250ms”
{6} “200ms”
{7} “160ms”
{8} “110ms”
{9} “100ms”
{*} “90ms”
{#} “80ms”
Note:
L If the unit is connected via a PBX, PBX functions (transferring a call, etc.)
might not work correctly. Consult your PBX supplier for the correct setting.
Changing the LCD display
contrast
{#}{1}{4}{5}
{1} “NORMAL” (default)
{2} “DARKER”
57
9. Programmable Features
Feature/Code
Selection
Changing the password for
feature programming via
remote operation
{#}{1}{5}{5}
1. {Menu} i {#}{1}{5}{5} i {Set}
2. Enter the current password. i {Set}
L The default password is “1234”.
3. Enter a new 4-digit password using 0–9. i {Set}
4. Enter the new password again. i {Set} i {Menu}
Note:
L It is recommended that you change this password from the default
password.
L This password is also used for feature programming via web browser.
Setting the toner
maintenance time
{#}{1}{5}{8}
The unit will automatically activate for maintenance, once every 24 hours.
Because this is to prevent the toner from solidifying, the noise that the unit
makes during maintenance cannot be stopped. However, if the unit’s noise
bothers you, you can change the start time.
1. {Menu} i {#}{1}{5}{8} i {Set}
2. Enter the maintenance start time.
L The default time is “12:00AM”.
L Press {*} repeatedly to select “AM” or “PM”.
L If you select French for the language (feature #110 on page 22), the
default time is “00:00”.
3. {Set} i {Menu}
Setting the ringer pattern
{#}{1}{6}{1}
{1} “A” (default)
{2} “B”
{3} “C”
Changing the ring count in
FAX ONLY mode
{#}{2}{1}{0}
{1} “1”
{2} “2”
{3} “3” (default)
{4} “4”
{5} “5 EXT. TAM” (External Telephone Answering Machine)
Setting the caller’s list to print
automatically
{#}{2}{1}{6}
{0} “OFF” (default): The unit will not print the caller’s list, but will keep records
of the information for the last 30 callers.
{1} “ON”: The unit will print the caller’s list automatically after every 30 new calls
(page 53).
Setting the time adjustment
{#}{2}{2}{6}
Using this feature, the unit’s date and time setting will be automatically adjusted
when caller information is received.
{1} “AUTO” (default): The date and time setting will be automatically adjusted.
{2} “MANUAL”: Deactivates this features.
Setting the recording paper
size in the standard input tray
{#}{3}{8}{0}
{1} “LETTER” (default): Letter-size paper
{2} “A4”: A4-size paper
{3} “LEGAL”: Legal-size paper
Setting the recording paper
size in the optional input tray
{#}{3}{8}{2}
This feature will be displayed only when the optional input tray is installed.
{1} “LETTER” (default): Letter-size paper
{2} “A4”: A4-size paper
{3} “LEGAL”: Legal-size paper
58
9. Programmable Features
Feature/Code
Selection
Setting the recording paper
type
{#}{3}{8}{3}
{1} “PLAIN PAPER” (default): 75 g/m2 to 105 g/m2 (20 lb to 28 lb) paper.
{2} “THIN PAPER”: 60 g/m2 to 74 g/m2 (16 lb to 19 lb) paper.
{3} “THICK PAPER”: 106 g/m2 to 165 g/m2 (29 lb to 44 lb) paper.
Note:
L This setting is valid for both the standard input tray and the optional input
tray.
L “THICK PAPER” will be displayed only when “#1” is selected for the
following:
– Paper input tray setting for fax (Feature #440 on page 63).
– Paper input tray setting for copy (Feature #460 on page 65).
– Paper input tray in PCL® (Feature #760 on page 66).
– Paper input tray setting for the scan to e-mail print feature (Feature #565
on page 72).
Setting the waiting time for
the power save mode
{#}{4}{0}{3}
To set the length of time before the unit enters the power save mode.
{1} “5min”: 5 minutes
{2} “15min” (default): 15 minutes
{3} “30min”: 30 minutes
{4} “1h”: 1 hour
Note:
L During the power save mode, the unit needs to preheat the fuser unit before
printing.
Setting the default operation
mode
{#}{4}{6}{3}
To select the default operation mode when the selected time of the mode timer
(feature #464) passes.
{1} “COPY” (default): Copy mode is selected as default.
{2} “FAX”: Fax mode is selected as default.
Note:
L You cannot select the scan mode using this feature.
Setting the default operation
mode timer
{#}{4}{6}{4}
To set the timer before returning to the default operation mode (feature #463).
{0} “OFF”: Deactivates this feature.
{1} “30s”: 30 seconds
{2} “1min” (default): 1 minute
{3} “2min”: 2 minutes
{4} “5min”: 5 minutes
Cleaning the drum
{#}{4}{8}{0}
Clean the drum cartridge automatically. See page 104 for details.
Setting toner save feature
{#}{4}{8}{2}
{0} “OFF” (default): Deactivates this feature.
{1} “ON”: The toner cartridge will last longer.
Note:
L This feature may lower the print quality by reducing toner consumption.
Changing the colour
calibration for all colours
(cyan, magenta, yellow and
black)
{#}{4}{8}{5}
Change the colour calibration if colour printing is too dark or too light. See page
77 for details.
Changing the colour
calibration for cyan colour
{#}{4}{8}{6}
Change the colour calibration if colour printing is too dark or too light. See page
77 for details.
Changing the colour
calibration for magenta
colour
{#}{4}{8}{7}
Change the colour calibration if colour printing is too dark or too light. See page
77 for details.
59
9. Programmable Features
Feature/Code
Selection
Changing the colour
calibration for yellow colour
{#}{4}{8}{8}
Change the colour calibration if colour printing is too dark or too light. See page
77 for details.
Changing the colour
calibration for black colour
{#}{4}{8}{9}
Change the colour calibration if colour printing is too dark or too light. See page
77 for details.
60
9. Programmable Features
9.3 Fax features
Feature/Code
Selection
Printing a confirmation report
{#}{4}{0}{1}
{0} “OFF”: Confirmation reports will not be printed.
{1} “ON”: A confirmation report will be printed after every fax transmission.
{2} “ERROR” (default): A confirmation report will be printed only when fax
transmission fails.
Setting the journal report to
print automatically
{#}{4}{0}{2}
{0} “OFF”: The unit will not print a journal report, but will keep a record of the
last 30 fax transmissions and receptions.
{1} “ON” (default): The unit will print a journal report automatically after every
30 new fax transmissions and receptions (page 43).
Sending documents
overseas
{#}{4}{1}{1}
If you cannot send a fax overseas even if the number is correct and the line is
connected, activate this feature before sending the fax.
This feature improves the reliability by reducing the transmission speed.
{0} “OFF”: Deactivates this feature.
{1} “NEXT FAX”: This setting is effective only for the next attempted fax
transmission. After transmission, the unit will return to the previous setting.
{2} “ERROR” (default): When the previous fax transmission fails and you wish to
re-send the document.
Note:
L This feature is not available for broadcast transmission.
L Calling charges may be higher than usual.
61
9. Programmable Features
Feature/Code
Selection
Sending a fax at a specific
time
{#}{4}{1}{2}
This feature allows you to take advantage of low-cost calling hours offered by
your telephone company. This feature can be set up to 24 hours in advance of
the desired time.
{0} “OFF” (default)
{1} “ON”
To send a document:
1. If the {Fax} light is OFF, turn it ON by pressing {Fax}.
2. Set the original (page 19).
3. If necessary, change to the desired resolution (page 43) and the desired
contrast (page 43).
4. {Menu} i {#}{4}{1}{2}
5. Press {1} to select “ON”. i {Set}
6. Enter the fax number.
L To enter an item using one-touch dial feature and navigator directory,
see step 3 on “6.3.1 Using the scanner glass”, page 45. (When using
navigator directory, you do not have to press {Directory} before
pressing {V} or {^}.)
7. {Set}
8. Enter the transmission start time.
L Press {*} repeatedly to select “AM” or “PM”.
L If you select French for the language (feature #110 on page 57), the time
is set using a 24 hour clock.
9. When using the scanner glass, press {Set}. i {Black}
When using the automatic document feeder, press {Set}.
L The document will be fed into the unit and scanned into memory. The
unit will then send the data at the specified time. You cannot use this
feature for another fax transmission until the former sending is
completed.
Note:
L To cancel after programming, press {Stop} while the unit is idle, and then
press {Set}.
Setting the Error Correction
Mode (ECM)
{#}{4}{1}{3}
This feature is available when the sending / receiving fax machines are ECM
compatible.
{0} “OFF”: Deactivates this feature.
{1} “ON” (default): If there is an error during fax transmission / reception, the
unit will support the communication.
Setting the connecting tone
{#}{4}{1}{6}
If you often have trouble when sending faxes, this feature allows you to hear
connecting tones: fax tone, ring back tone and busy tone. You can use these
tones to confirm the status of the other party’s machine.
{0} “OFF”: Deactivates this feature.
{1} “ON” (default): You will hear connecting tones.
Note:
L If the ring back tone continues, the other party’s machine may not be a fax
machine or may have run out of paper. Check with the other party.
L The connecting tone volume cannot be adjusted.
Setting the maximum fax
speed
{#}{4}{1}{8}
62
{1} “14.4Kbps”
{2} “33.6Kbps” (default)
Note:
L The fax speed maybe lower than the selected speed according to your line.
9. Programmable Features
Feature/Code
Selection
Activating the Distinctive
Ring feature
{#}{4}{3}{0}
{0} “OFF” (default)
{1} “ON”
See page 55 for details.
Setting the ring pattern for fax
(Distinctive Ring feature)
{#}{4}{3}{1}
{1} “A”
{2} “B”
{3} “C”
{4} “D”
{5} “B-D” (default)
See page 55 for details.
Setting auto reduction
feature
{#}{4}{3}{2}
To receive a fax document that is longer than your recording paper.
{0} “OFF”: The unit will print the original size.
{1} “ON” (default): The unit will fit received documents onto your recording
paper.
Changing the fax activation
code
{#}{4}{3}{4}
If you wish to use an extension telephone to receive faxes, activate this feature
and program the activation code.
Important:
L The fax activation code must be different from the code that you
programmed on the answering machine.
{0} “OFF” (default)
{1} “ON”
1. {Menu} i {#}{4}{3}{4}
2. Press {1} to select “ON”. i {Set}
3. Enter your code from 2 to 4 digits, using 0–9, {*} and {#}.
L The default code is “;#9”.
L Do not enter “0000”.
4. {Set} i {Menu}
Setting the memory reception
alert
{#}{4}{3}{7}
To alert you with a beeping sound when a received fax document is stored into
memory due to some existing problem.
{0} “OFF”: Deactivates this feature.
{1} “ON” (default): You will hear a beeping sound.
Note:
L The slow beeps will continue until you solve the printing problem and make
sure the unit is supplied with enough paper to print the stored document.
Setting friendly reception
{#}{4}{3}{8}
To receive a fax automatically when you answer a call and hear a fax calling
tone (slow beep).
{0} “OFF”: You have to press {Black} for fax reception.
{1} “ON” (default): You do not have to press {Black} for fax reception.
Setting the paper input tray to
use for printing received
faxes
{#}{4}{4}{0}
This feature will be displayed only when the optional input tray is installed.
{1} “#1” (default): Standard input tray
{2} “#2”: Optional input tray
{3} “#1+#2”
Note:
L If you select “#1+#2”, make sure the same paper size is selected for the
following:
– Standard input tray (feature #380 on page 58)
– Optional input tray (feature #382 on page 58)
If either is changed, “#1” will be selected automatically.
63
9. Programmable Features
Feature/Code
Selection
Receiving a fax into the
computer
{#}{4}{4}{2}
If you wish to receive a fax into the computer, activate this feature and run [PC
FAX] from Multi-Function Station.
{0} “OFF” (default): Deactivates this feature.
{1} “ALWAYS”: If the unit recognizes the connection to the computer, it will
transfer a received document to the computer. If the unit cannot recognize the
connection, it will store a received document in the memory once, then transfer
the data after recognition of the connection.
{2} “CONNECTED”: If the unit recognizes the connection to the computer, it will
transfer a received document to the computer. If the unit cannot recognize the
connection, it will print out the data.
Setting the computer for PC
fax reception
{#}{4}{4}{3}
To select the computer that will be used for receiving a fax. See page 24 for
details.
Sending legal size
documents using the scanner
glass
{#}{4}{4}{5}
{0} “OFF” (default): Deactivates this feature.
{1} “NEXT FAX”: Legal-size documents can be sent for the next fax
transmission using the scanner glass. After transmission, this setting will turn
OFF automatically.
{2} “ALWAYS”: Legal-size documents can be sent using the scanner glass
anytime.
Resetting fax features to their
default settings
{#}{4}{5}{9}
{0} “NO” (default)
{1} “YES”
To reset the fax features:
1. {Menu} i {#}{4}{5}{9}
2. Press {1} to select “YES”. i {Set} i {Set} i {Menu}
Note:
L The PC fax reception (feature #443 on page 24) will not be reset.
64
9. Programmable Features
9.4 Copy features
Feature/Code
Selection
Setting the paper input tray to
use for copy
{#}{4}{6}{0}
This feature will be displayed only when the optional input tray is installed.
{1} “#1” (default): Standard input tray
{2} “#2”: Optional input tray
{3} “#1+#2”
Note:
L If you select “#1+#2”, make sure the same paper size is selected for the
following:
– Standard input tray (feature #380 on page 58)
– Optional input tray (feature #382 on page 58)
If either is changed, “#1” will be selected automatically.
Changing the default copy
resolution
{#}{4}{6}{1}
To change the default resolution setting for copying.
{1} “TEXT/PHOTO” (default): For documents containing both text and
photographs.
{2} “TEXT”: For documents containing only text.
{3} “PHOTO”: For documents containing photographs, shaded drawings, etc.
Holding the previous contrast
setting
{#}{4}{6}{2}
{0} “DISABLED” (default): Deactivates this feature.
{1} “ENABLED”: The unit will hold the previous setting.
Holding the previous page
layout setting
{#}{4}{6}{7}
{0} “DISABLED” (default): Deactivates this feature.
{1} “ENABLED”: The unit will hold the previous setting.
Holding the previous zoom
setting
{#}{4}{6}{8}
{0} “DISABLED” (default): Deactivates this feature.
{1} “ENABLED”: The unit will hold the previous setting.
Holding the previous collate
setting
{#}{4}{6}{9}
{0} “DISABLED” (default): Deactivates this feature.
{1} “ENABLED”: The unit will hold the previous setting.
Holding the previous duplex
setting
{#}{4}{7}{0}
This feature will be displayed only when the automatic duplex unit is installed.
{0} “DISABLED” (default): Deactivates this feature.
{1} “ENABLED”: The unit will hold the previous setting.
Note:
L The previous setting will be held individually for copying and sending faxes.
65
9. Programmable Features
9.5 PC print features
Feature/Code
Selection
Setting the paper input tray in
PCL
{#}{7}{6}{0}
This feature will be displayed only when the optional input tray is installed.
{1} “#1” (default): Standard input tray
{2} “#2”: Optional input tray
{3} “#1+#2”
Note:
L If you select “#1+#2”, make sure the same paper size is selected for the
following:
– Standard input tray (feature #380 on page 58)
– Optional input tray (feature #382 on page 58)
If either is changed, “#1” will be selected automatically.
Setting the number of copies
in PCL
{#}{7}{6}{2}
1. {Menu} i {#}{7}{6}{2} i {Set}
2. Enter the number of copies from “001” to “999”, using the dial keypad.
L The default setting is “001”.
3. {Set} i {Menu}
Setting the recording paper
size in PCL
{#}{7}{6}{3}
{1} “LETTER” (default): Letter-size paper
{2} “A4”: A4-size paper
{3} “LEGAL”: Legal-size paper
Setting the image reduction
feature in PCL
{#}{7}{6}{4}
{0} “OFF”: Deactivates this feature.
{1} “ON” (default): The document resolution will be automatically reduced
when the data size is too large to print.
Note:
L This feature may lower the print quality by reducing the resolution.
Setting the recording paper
direction in PCL
{#}{7}{6}{5}
{1} “PORTRAIT” (default): The document will be printed in portrait direction.
{2} “LANDSCAPE”: The document will be printed in landscape direction.
Setting the A4 wide feature in
PCL
{#}{7}{6}{6}
You can change the margin and printable area of A4-size recording paper so
that 80 characters in 10 cpi font may be printed on a line.
{0} “OFF” (default): Deactivates this feature.
{1} “ON”: The margin and printable area of A4 recording paper will be changed.
Setting the line per page in
PCL
{#}{7}{6}{7}
To set the number of lines per page in PCL printing.
1. {Menu} i {#}{7}{6}{7} i {Set}
2. Enter the number of lines per page from “005” to “128”, using the dial
keypad.
L The default setting is “060”.
3. {Set} i {Menu}
Setting the font source in PCL
{#}{7}{6}{8}
66
This feature is available when the downloaded font is registered to the unit.
{1} “RESIDENT” (default): The document will be printed using resident font.
{2} “DOWNLOAD FONT”: The document will be printed using download font.
9. Programmable Features
Feature/Code
Selection
Setting the font number in
PCL
{#}{7}{6}{9}
To set the font number to be used in PCL printing. The unit assigns a number
to each font.
1. {Menu} i {#}{7}{6}{9} i {Set}
2. Enter the font number from “000” to “054”, using the dial keypad.
L The default setting is “000”.
3. {Set} i {Menu}
Note:
L If feature #768 is set to “DOWNLOAD FONT”, the default setting is “001”.
L To print the font list, see page 104.
Setting the font pitch/point in
PCL
{#}{7}{7}{0}
To set the font pitch/point to be used in PCL printing.
1. {Menu} i {#}{7}{7}{0} i {Set}
2. Enter the font pitch from “00.44” to “99.99”, or the point from “004.00”
to “999.75”, using the dial keypad.
L The default pitch is “10.00” and the default point is “012.00”.
3. {Set} i {Menu}
Setting the symbol set in PCL
{#}{7}{7}{1}
To set the symbol set to be used in PCL printing.
1. {Menu} i {#}{7}{7}{1}
2. Press {V} or {^} repeatedly to display the desired symbol set. i {Set}
i {Menu}
Setting the line breaks in PCL
{#}{7}{7}{2}
To set each behaviour when receiving CR, LF, and FF codes.
{1} “CR/LF/FF” (default): CR=CR, LF=LF, FF=FF
{2} “CR+LF/LF/FF”: CR=CR+LF, LF=LF, FF=FF
{3} “CR/CR+LF/CR+FF”: CR=CR, LF=CR+LF, FF=CR+FF
Setting the waiting time for
auto continue mode
{#}{7}{7}{3}
To set the length of time before the unit recovers if a memory overflow occurs.
{1} “OFF” (default): Deactivates this feature.
{2} “20s”: 20 seconds
{3} “30s”: 30 seconds
{4} “60s”: 60 seconds
{5} “90s”: 90 seconds
{6} “120s”: 120 seconds
Changing the data timeout
setting
{#}{7}{7}{4}
The unit will automatically print the remaining data in memory when the
computer does not send data to the unit during the set time.
1. {Menu} i {#}{7}{7}{4} i {Set}
2. Enter the desired data timeout setting from “005” seconds to “600”
seconds, using the dial keypad.
L The default setting is “060” seconds.
3. {Set} i {Menu}
Detecting monochrome
pages
{#}{7}{7}{5}
{0} “OFF”: When you make a colour printout, all pages including monochrome
pages will be printed using colour toner cartridge and colour drum cartridge.
This will increase consumable usage for colour toner cartridge and colour drum
cartridge.
{1} “ON” (default): When you make a colour printout, this feature automatically
detects the monochrome pages of your document and print only using the black
toner cartridge and monochrome drum cartridge. This will decrease
consumable usage for colour toner cartridge and colour drum cartridge, but will
require time to automatically switch between monochrome printing and colour
printing.
Note:
L Depending on the type of document, this feature may not be activated even
when “ON” is selected.
67
9. Programmable Features
Feature/Code
Selection
Setting mutual A4/letter print
{#}{7}{7}{6}
This feature allows printing in A4-size even if letter-size recording paper is
installed, and vice versa.
{0} “OFF”: Deactivates this feature.
{1} “ON” (default): Printing is possible between A4/letter-size.
68
9. Programmable Features
9.6 Scan features
Feature/Code
Selection
Setting the scan mode for
Push Scan
{#}{4}{9}{3}
{1} “VIEWER” (default): The scanned image will be displayed in the [MultiFunction Viewer] window.
{2} “FILE”: The scanned image will be saved as a file.
{3} “E-MAIL”: The scanned image will be saved for e-mail attachment.
{4} “OCR”: The scanned image will be displayed in the OCR window.
{5} “E-MAIL SERVER”: The scanned image will be sent as an attachment
without using e-mail software.
{6} “FTP SERVER”: The scanned image will be sent to the pre-programmed
folder on the FTP server.
Note:
L Following selections will be displayed only when the server setting is
programmed through the web browser interface in advance.
– “E-MAIL SERVER” will be displayed when the e-mail server setting is
programmed (page 69).
– “FTP SERVER” will be displayed when the FTP server setting is
programmed (page 70).
Holding the previous
scanning parameter for Push
Scan
{#}{4}{9}{4}
{0} “DISABLED” (default): Deactivates this feature.
{1} “ENABLED”: The unit will hold the previous scan settings for each mode of
push scan; scan size, resolution, file format, brightness, colour
contrast/contrast.
Setting the monochrome
scan type
{#}{4}{9}{5}
{1} “BLACK/WHITE” (default): To scan as black lines, select this for text
contents.
{2} “GREYSCALE”: To scan as black lines and grey shades, select this for
images.
Setting the information for
scan to e-mail (via e-mail
server) (LAN connection
only)
L This feature can be
programmed only through
the web browser interface.
When you send scanned files via e-mail server, you need to program the e-mail
server and SMTP server settings beforehand. Consult your service provider or
network administrator for details.
1. Start Multi-Function Station.
2. [Utilities] i [Configuration Web Page] i [Device Configuration]
3. Type “root” as the user name, then enter the password (feature #155 on
page 58). i [OK]
4. Select the [SCAN FEATURE] tab.
5. Click [Edit] next to [E-MAIL SERVER].
6. Enter the e-mail server and SMTP server information. i [Submit]
7. Close the web browser.
69
9. Programmable Features
Feature/Code
Selection
Registering the scan to e-mail
destinations (via e-mail
server) (LAN connection
only)
L This feature can be
programmed only through
the web browser interface.
When you send scanned files via e-mail server, you can register e-mail
destinations (up to 300 destinations) for the unit through the web browser
interface in advance.
1. Start Multi-Function Station.
2. [Utilities] i [Configuration Web Page] i [Device Configuration]
3. Type “root” as the user name, then enter the password (feature #155 on
page 58). i [OK]
4. Select the [SCAN FEATURE] tab.
5. Click [Edit] next to [SEND USER].
6. Click [Edit] next to the desired scan to e-mail user.
7. Enter name and e-mail address, then select the station key number from the
drop-down list if necessary. i [Submit]
8. Close the web browser.
Setting the information for
scan to FTP (LAN connection
only)
L This feature can be
programmed only through
the web browser interface.
When you send scanned files to an FTP server, you can register FTP
destinations (up to 6 destinations) to the unit through the web browser interface
in advance.
1. Start Multi-Function Station.
2. [Utilities] i [Configuration Web Page] i [Device Configuration]
3. Type “root” as the user name, then enter the password (feature #155 on
page 58). i [OK]
4. Select the [SCAN FEATURE] tab.
5. Click [Edit] next to [FTP SERVER].
6. Click [Edit] next to the desired FTP server destination.
7. Enter the server name, IP address, folder directory, etc. i [Submit]
8. Close the web browser.
Note:
L If you do not enter the folder directory in step 7, the scanned image will be
saved in the root folder.
70
9. Programmable Features
9.7 LAN features
Feature/Code
Selection
LAN setting with a DHCP
server
{#}{5}{0}{0}
{0} “DISABLED”: Deactivates this feature.
{1} “ENABLED” (default): The following will be allocated automatically using a
DHCP (Dynamic Host Configuration Protocol) server.
– IP address
– Subnet mask
– Default gateway
Setting the IP address for the
LAN connection
{#}{5}{0}{1}
This feature is available when feature #500 is deactivated.
Setting the Subnet mask for
the LAN connection
{#}{5}{0}{2}
This feature is available when feature #500 is deactivated.
Setting the default gateway
for the LAN connection
{#}{5}{0}{3}
This feature is available when feature #500 is deactivated.
Setting the primary DNS
server for the LAN
connection
{#}{5}{0}{4}
This feature is available when feature #500 is deactivated.
Setting the secondary DNS
server for the LAN
connection
{#}{5}{0}{5}
This feature is available when feature #500 is deactivated.
Setting the machine name
{#}{5}{0}{7}
1. {Menu} i {#}{5}{0}{7} i {Set}
1. {Menu} i {#}{5}{0}{1} i {Set}
2. Enter the IP address of the unit on the LAN using the dial keypad. i {Set}
i {Menu}
1. {Menu} i {#}{5}{0}{2} i {Set}
2. Enter the subnet mask of the network on the LAN using the dial keypad. i
{Set} i {Menu}
1. {Menu} i {#}{5}{0}{3} i {Set}
2. Enter the default gateway of the network on the LAN using the dial keypad.
i {Set} i {Menu}
1. {Menu} i {#}{5}{0}{4} i {Set}
2. Enter the primary DNS server of the network on the LAN using the dial
keypad. i {Set} i {Menu}
1. {Menu} i {#}{5}{0}{5} i {Set}
2. Enter the secondary DNS server of the network on the LAN using the dial
keypad. i {Set} i {Menu}
2. Enter the name of the unit to recognize on the LAN, up to 15 characters (see
page 75 for character entry). i {Set} i {Menu}
Note:
L In order to recognize the unit on the LAN, the default name of the unit is
assigned automatically. If you change the name, assign a unique name to
avoid overlapping.
Displaying the MAC address
of the unit
{#}{5}{0}{8}
1. {Menu} i {#}{5}{0}{8} i {Set}
2. The MAC address of the unit will be displayed. i {Menu}
71
9. Programmable Features
Feature/Code
Selection
IP filtering for the LAN
connection
{#}{5}{3}{2}
{0} “DISABLED” (default): Deactivates this feature.
{1} “ENABLED”: The unit will deny/approve access from the pre-programmed
IP patterns. Whether to deny or approve, and up to 4 patterns can be
programmed through the web browser interface.
1. Start Multi-Function Station.
2. [Utilities] i [Configuration Web Page] i [Network Configuration]
3. Type “root” as the user name, then enter the password (feature #155 on
page 58). i [OK]
4. Select the [LAN FEATURE] tab.
5. Click [Edit] next to [IP FILTERING].
6. Click [Edit] next to [FILTER].
7. Change the mode and edit IP filtering information. i [Submit]
8. Close the web browser.
Setting the IP address
automatically for the LAN
connection
{#}{5}{3}{3}
This feature will be displayed only when feature #500 is activated.
{0} “DISABLED” (default): Deactivates this feature.
{1} “ENABLED”: IP address will be allocated automatically without using a
DHCP (Dynamic Host Configuration Protocol) server.
Setting HTTPD for the LAN
connection
{#}{5}{3}{4}
{0} “DISABLED”: Denies access to the web browser.
{1} “ENABLED” (default): Allows access to the web browser.
IPv6 protocol
{#}{5}{3}{5}
{0} “DISABLED” (default): Deactivates this feature.
{1} “ENABLED”: IPv6 protocol can be used. After installing the printer driver, be
sure to change the port to IPv6 protocol. You can check the IPv6 protocol
address by printing the “SETUP LIST” (page 104).
Note:
L To activate this feature, you need to turn the power switch of the unit OFF,
then ON.
Setting the paper input tray to
use for the scan to e-mail
print feature
{#}{5}{6}{5}
This feature will be displayed only when the optional input tray is installed.
{1} “#1” (default): Standard input tray
{2} “#2”: Optional input tray
{3} “#1+#2”
Note:
L If you select “#1+#2”, make sure the same paper size is selected for the
following:
– Standard input tray (feature #380 on page 58)
– Optional input tray (feature #382 on page 58)
If either is changed, “#1” will be selected automatically.
72
9. Programmable Features
9.8 Network features (LAN connection only)
These features can be programmed only through the web browser interface.
Feature
Tab
Selection
Setting the community
name for SNMP
[SNMP]
Enter the SNMP community name. Consult your
service provider or network administrator for details.
Setting the location
where you use this unit
[SNMP]
Enter the location information of the unit.
Displaying the link local
address
[IPv6]
The link local address will be displayed.
Displaying the IP
address for auto
configuration
[IPv6]
The IP address for auto configuration will be displayed.
Setting the IP address
for IPv6
[IPv6]
Enter the IP address for IPv6. Consult your service
provider or network administrator for details.
Setting the default
router for IPv6
[IPv6]
Enter the default router address for IPv6. Consult your
service provider or network administrator for details.
Setting the information
for scan to FTP
[FTP FEATURE]
Enter the FTP server information to send scanned
images from the unit to an FTP server. See page 70 for
details.
Setting the information
for scan to e-mail (via email server)
[E-MAIL FEATURE]
Enter the e-mail server and SMTP server information to
send scanned images from the unit via e-mail. See
page 69 for details.
Registering the scan to
e-mail destinations (via
e-mail server)
[E-MAIL FEATURE]
Register e-mail destinations (up to 300 destinations) for
the unit. See page 70 for details.
Setting the error notify
feature
[ERROR NOTIFY]
[ENABLED]: The unit will send an e-mail to registered
destinations when a problem occurs.
[DISABLED] (default): Deactivates this feature.
Setting the information
for the error notify
feature
[ERROR NOTIFY]
Enter the e-mail server and SMTP server information to
send error notification e-mails to.
Registering
destinations for the
error notify feature
[ERROR NOTIFY]
Enter the e-mail address to which error notifications will
be sent and select the types of problems.
[LIFE WARNING]: A warning indicating that the toner
cartridge, drum cartridge or waste toner cartridge
needs to be replaced soon.
[MEDIA PATH ERROR]: An error indicating that there
is a problem with the paper input tray.
[LIFE ERROR]: An error indicating that the toner
cartridge, drum cartridge or waste toner cartridge
needs to be replaced.
Setting the scan to email print feature
[SCAN TO E-MAIL
PRINT]
[ENABLED]: The unit will automatically print e-mail
attachment that it receives.
[DISABLED] (default): Deactivates this feature.
See page 30 for details.
Setting the e-mail
checking interval for the
scan to e-mail print
feature
[SCAN TO E-MAIL
PRINT]
Enter the desired e-mail checking interval.
73
9. Programmable Features
Feature
Tab
Selection
Setting the header print
option for the scan to email print feature
[SCAN TO E-MAIL
PRINT]
[ENABLED] (default): The unit will print received email attachment with the header information.
[DISABLED]: Deactivates this feature.
Setting the information
for the scan to e-mail
print feature
[SCAN TO E-MAIL
PRINT]
When you use the scan to e-mail print feature, you need
to program the POP server setting beforehand. See
page 30 for details.
Displaying the scan to
e-mail print information
[SCAN TO E-MAIL
PRINT]
The information for the 30 most recently received emails will be displayed.
Note:
L See the following sections for details on these related features:
– DHCP mode (feature #500 on page 71)
– IP address (feature #501 on page 71)
– Subnet mask (feature #502 on page 71)
– Default gateway (feature #503 on page 71)
– DNS server #1 (feature #504 on page 71)
– DNS server #2 (feature # 505 on page 71)
– Machine name (feature #507 on page 71)
– IP filtering (feature #532 on page 72)
– Auto IP (feature #533 on page 72)
– HTTPD (feature #534 on page 72)
– IPv6 protocol (feature #535 on page 72)
– Paper input tray setting for the scan to e-mail print feature (feature #565 on page 72)
74
10. Useful Information
2. Press {>} to insert the displayed character.
10 Useful
Useful
Information
Information
10.1 Character entry
3. Return to step 1 to enter the next character.
The dial keypad is used to enter characters and
numbers.
– Press {<} or {>} to move the cursor.
– Press dial keys to enter characters and numbers.
– Press {Stop} to erase the character or number
highlighted by the cursor. Press and hold {Stop} to
erase all characters or numbers.
– To enter another character located on the same dial
key, press {>} to move the cursor to the next space,
then press the appropriate dial key.
Keypad
Characters
{1}*1
1
.
_
–
[
]
{
}
/
= ,
`
:
;
?
|
{2}
A B C a
b
c
2
{3}
D E F d
e
f
3
{4}
G H I
g
h
i
4
{5}
J
j
k
l
5
{6}
M N O m n
o
6
{7}
P Q R S p
q
r
{8}
T U V t
u
v
8
{9}
W X Y Z w
x
{0}*2
0
@ (
)
<
$
% & ¥
@
K L
+
s
7
y
z
9
>
!
"
#
^
’
→
{#}
To switch between uppercase
or lowercase letters.
{Flash}
Hyphen
{Zoom}
To insert a space.
{Stop}
To delete a character.
*1 [ ] + / = , ` : ; ? | cannot be
entered when setting the machine name (feature
#507 on page 71).
*2 < > " ¥ @ → cannot be entered when
setting the machine name (feature #507 on page 71).
To select characters using {V} or {^}
Instead of pressing the dial keys, you can select
characters using {V} or {^}.
1. Press {V} repeatedly to display the desired
character. Characters will be displayed in the
following order:
1 Uppercase letters
2 Number
3 Symbol
4 Lowercase letters
L If you press {^}, the order will be reversed.
75
10. Useful Information
10.2 Status of the unit
10.2.2 Using Device Monitor
10.2.1 Using Remote Control
1 Start Multi-Function Station.
2 [Utilities] i [Device Monitor]
You can easily operate the following functions from your
computer.
– Programming the features (page 57)
– Storing, editing or erasing items in directories (page
44)
– Storing or erasing items for broadcast transmission
(page 46)
– Viewing items in the journal report (page 43)
– Saving the journal report on your computer
– Viewing items in the caller’s list (page 53)
– Storing caller information into directories (page 54)
– Saving the caller’s list on your computer
1 Start Multi-Function Station. i [Remote Control]
L The [Multi-Function Remote Control] window
will appear.
You can confirm the setting information and current
status of the unit from your computer.
L The [Device Monitor] window will appear.
3 Confirm the status of the unit.
[Status]: Current status of the unit
Note:
L Additional information (toner and recording paper
status, unit information, etc.) will be displayed in
[Status] tab by clicking [Advanced Information].
L You can update the status of the unit by clicking
[Refresh].
L If a printing error occurs, the Device Monitor will start
automatically and display the error information.
L For details, see the help file by selecting [p] from
Multi-Function Station.
10.2.3 Using the web browser (LAN
connection only)
You can confirm the setting information and status of the
unit from the web browser.
1 Start Multi-Function Station. i [Utilities] i
[Configuration Web Page]
L You can also access the unit by entering its IP
address in a web browser.
2 Select a category from the menu bar.
2 Select the desired tab.
L The latest data in the unit will be displayed.
3 Perform the desired operation.
L For details about each function, click [Help].
L To stop the operation, click [Cancel].
4 [OK]
L You can also click [Apply] to continue the next
operation without closing the window.
5 Enter the password (feature #155 on page 58). i
[OK]
L The new data will be transferred to the unit and
the window will close.
Note:
L Some of the features cannot be programmed from
your computer.
L For details, see the help file by selecting [p] from
Multi-Function Station.
L When another person is adjusting stored data in the
unit, it may be overwritten. Make sure the unit is not
currently being used for the same function.
76
[Status]: Toner and paper information, etc.
[Device]: Current status of the unit, etc.
[Network]: Network information, etc.
L When you select [Device] or [Network], you
can change which features are displayed by
clicking the feature tabs at the top of the right
frame.
3 Confirm the status of the unit.
Note:
L You can update the status of the unit by clicking
[Reload].
10. Useful Information
10.3 Cancelling the operations
You can cancel the current operation from the unit. You
can also select the desired operation to cancel.
1 {Stop}
L “USER STOPPED” is displayed.
L When “USER STOPPED” is not displayed, go to
step 2.
10.4 Changing the colour
calibration
If colour printing is too dark or too light, change the
colour calibration.
1 Select the desired colour to change the calibration.
L To change the colour density for cyan, magenta,
yellow and black, press {Menu}. i
{#}{4}{8}{5}
L To change the colour calibration for cyan, press
{Menu}. i {#}{4}{8}{6}
L To change the colour calibration for magenta,
press {Menu}. i {#}{4}{8}{7}
L To change the colour calibration for yellow, press
{Menu}. i {#}{4}{8}{8}
L To change the colour calibration for black, press
{Menu}. i {#}{4}{8}{9}
2 To cancel printing:
Press {Stop} repeatedly to display “STOP
PRINTING?”.
To cancel scanning:
Press {Stop} repeatedly to display “STOP
SCANNING?”.
To cancel copying:
Press {Stop} repeatedly to display “STOP
COPYING?”.
2 Select the desired colour calibration.
{0} “-5”
{1} “-4”
{2} “-3”
{3} “-2”
{4} “-1”
{5} “0” (default)
{6} “1”
{7} “2”
{8} “3”
{9} “4”
{*} “5”
To cancel sending or receiving faxes:
Press {Stop} repeatedly to display “STOP FAX?”.
To cancel broadcast transmission:
Press {Stop} repeatedly to display “BROAD
CANCELLED?”.
To cancel fax redialing:
Press {Stop} repeatedly to display “SEND
CANCELLED?”.
3 {Set}
3 {Set}
4 Press {Menu} to exit.
Printing a colour test list
You can print the colour test list to check the colour
density for each colour (page 104).
Option
77
10. Useful Information
3 Lift the handset cradle in the direction of the arrow
10.5 Optional handset unit
You can add the optional handset unit. See page 7 for
accessory information.
Important:
L Before installing or removing the optional
handset unit, be sure to turn the power switch
OFF. For more details about the installation,
please refer to the installation guide for the
optional handset unit.
1 Connect the handset cord (1) to the handset cradle.
(4) to insert the tab (5), then insert the rib (6) by
pushing the handset unit toward the unit.
6
4
5
1
2 Connect the handset connector (2).
L Remove the cover (3) from the handset unit
connection jack if attached.
4 Pull out the handset cord holder (7) and pass the
handset cord (8) through the handset cord holder.
8
2
78
3
7
10. Useful Information
5 Place the handset (9) on the handset cradle, then
connect the handset cord to the handset (j).
3. Pull the handset unit slightly forward (4), then lift it in
the direction of the arrow (5) to remove the rib.
5
9
4
4. Remove the tab (6), then disconnect the handset
connector (7).
j
Note:
L While talking to the other party, you can send a fax
using the scanner glass by pressing {Black} i {1}
(To receive a fax, press {2}).
To remove the handset unit
1. Disconnect the handset cord (1) from the handset,
then remove the handset (2) from the handset
cradle.
6
7
2
1
2. Remove the handset cord from the handset cord
holder (3), then close the handset cord holder.
3
79
10. Useful Information
–
10.6 Optional automatic duplex
unit
You can add the optional automatic duplex unit. See
page 7 for accessory information.
A4, letter or legal-size recording paper (plain and thin)
can be used.
Important:
L Before starting installation of the optional
automatic duplex unit, be sure to turn the power
switch OFF. For more details about the
installation, please refer to the installation guide
for the optional automatic duplex unit.
L To use the optional automatic duplex unit with
your computer, you need to change the printer
properties. See page 81 for details.
To use thin paper, change the recording paper
type setting (feature #383 on page 59).
Important:
L Before starting installation of the optional input
tray, be sure to turn the power switch OFF. For
more details about the installation, please refer
to the installation guide for the optional input
tray.
L After installation, you can select the optional
input tray for the following:
– Paper input tray setting for faxing (feature
#440 on page 63).
– Paper input tray setting for copying (feature
#460 on page 65).
– Paper input tray in PCL (feature #760 on page
66).
– Paper input tray setting for the scan to e-mail
print feature (feature #565 on page 72).
L To use the optional input tray with your
computer, you need to change the printer
properties. See page 81 for details.
Caution for the optional input tray
L Do not drop the optional input tray.
10.7 Optional input tray
You can add the optional input tray. See page 7 for
accessory information.
L Hold the optional input tray with both hands
when removing or installing. The optional input
tray weighs approximately 4.8 kg (10.6 lb) when
the recording paper is fully installed.
A4, letter or legal-size recording paper (plain and thin)
can be used.
The optional input tray can hold:
– Up to 520 sheets of 75 g/m2 (20 lb) paper.
– Up to 470 sheets of 80 g/m2 (21 lb) paper.
– Up to 410 sheets of 90 g/m2 (24 lb) paper.
– Up to 360 sheets of 105 g/m2 (28 lb) paper.
L The unit is set for printing letter-size plain paper
by default.
– To use A4 or legal-size paper, change the
recording paper size setting (feature #382 on
page 58).
80
10. Useful Information
Do not touch the plate (1) on the left side of the
optional input tray.
1
5 Click [Auto Configuration] on the [Device] tab.
i [OK]
L The optional input tray and/or optional automatic
duplex unit will be automatically detected.
– For [Number of Input Tray], [2] will be
selected.
– For [Automatic Duplex Unit], [Installed]
will be selected.
If the setting is not changed automatically,
change it manually.
6 [OK]
Approx. 4.8 kg (10.6 lb)
L Do not position the unit in a location where it is
unstable or subject to vibrations. The unit weighs
approximately 40 kg (88 lb) when the optional input
tray is installed and the recording paper is fully
installed.
10.8 Setting the optional input
tray/optional automatic duplex
unit
To use the optional input tray/optional automatic duplex
unit with your computer, proceed as follows.
1 [Start]
2 Open the printer window.
For Windows 98/Windows Me/Windows 2000:
[Settings] i [Printers]
For Windows XP Professional:
[Printers and Faxes]
For Windows XP Home:
[Control Panel] i [Printers and Other
Hardware] i [Printers and Faxes]
For Windows Vista:
[Control Panel] i [Printers]
3 Select the unit’s name.
4 For Windows 98/Windows Me/Windows
2000/Windows XP:
Select [Properties] from the [File] menu.
L The printer properties window will appear.
For Windows Vista:
Select [Properties] from the [Organize] menu.
L The printer properties window will appear.
81
11. Help
11 Help
Error
Messages
11.1 Error messages – Reports
If a problem occurs during fax transmission or reception, one of the following messages will be printed on the
confirmation and journal reports (page 43).
Message
COMMUNICATION ERROR
Code
40-42
46-72
FF
Cause & Solution
L A transmission or reception error occurred. Try
again or check with the other party.
43
44
L A line problem occurred. Connect the telephone line
cord to a different jack and try again.
L An overseas transmission error occurred. Try using
the overseas mode (feature #411 on page 61).
DOCUMENT JAMMED
-----
L Remove the jammed document (page 100).
ERROR-NOT YOUR UNIT
53
54
59
70
L A transmission or reception error occurred because
of a problem with the other party’s fax machine.
Check with the other party.
JUNK FAX PROH. REJECT
-----
L The junk fax prohibitor feature of this unit rejected
fax reception.
MEMORY FULL
-----
L The memory is full of received documents due to a
lack of recording paper or a recording paper jam.
Install paper (page 14) or remove the jammed paper
(page 95).
L If feature #442 is set to “ALWAYS” (page 64), check
the connection between the computer and the unit.
NO DOCUMENT / FAILED PICKUP
-----
L The document was not fed into the unit properly. Reinsert it and try again.
OTHER FAX NOT RESPONDING
-----
L The other party’s fax machine is busy or has run out
of recording paper. Try again.
L The other party’s fax machine rings too many times.
Send the fax manually (page 43).
L The other party’s machine is not a fax machine.
Check with the other party.
L The number you dialed is not in service.
PRESSED THE ‘Stop’ KEY
-----
L {Stop} was pressed and fax communication was
cancelled.
THE COVER WAS OPENED
-----
L The front or left cover was opened. Close it and try
again.
OK
-----
L Fax transmission or reception was successful.
82
11. Help
11.2 Error messages – Display
If the unit detects a problem, one or more of the following messages will appear on the display.
Display
Cause & Solution
“BLACK TONER EMPTY”
“CYAN TONER EMPTY”
“MAGENTA TONER EMPTY”
“YELLOW TONER EMPTY”
b
“CHANGE SUPPLIES”
L The toner cartridge life is finished. Replace the toner cartridge immediately.
“BLACK TONER LOW”
“CYAN TONER LOW”
“MAGENTA TONER LOW”
“YELLOW TONER LOW”
b
“CHANGE SUPPLIES”
L The toner cartridge life is near its end. Replace the toner cartridge as soon
as possible.
“CALL SERVICE”
L There is something wrong with the unit. Contact our service personnel.
“CHECK DOCUMENT”
L The document was not fed into the unit properly. Remove the document,
then press {Stop} to clear the message. Re-insert the document. If
misfeeding occurs frequently, clean the document feeder rollers (page 102)
and try again.
“CHECK INSTALL INPUT
TRAY #1”
L The paper input tray is not installed correctly. Pull out the paper input tray
and re-insert it.
Note:
L “#1”: Standard input tray
L “#2”: Optional input tray
L “#1+#2”: Standard input tray and optional input tray
“CHECK PAPER”
L You are printing on envelopes. Check the standard input tray to be sure that
envelopes are installed, then press {Black}/{Colour}.
L The recording paper size is not same as the size that is selected for copy.
Change the recording paper size setting (feature #380 on page 58 or
feature #382 on page 58), and install appropriate recording paper.
L The recording paper size is not same as the size that is selected when
printing from the PC. Change the recording paper size setting (feature #380
on page 58 or feature #382 on page 58), and install appropriate recording
paper.
L The recording paper size is not same as the size that is selected for
receiving a fax. Change the recording paper size setting (feature #380 on
page 58 or feature #382 on page 58), and install appropriate recording
paper.
“CHECK PICK UP INPUT
TRAY #1”
L Recording paper was not fed into the unit properly. Re-insert the recording
paper (page 99).
Note:
L “#1”: Standard input tray
L “#2”: Optional input tray
“COLOUR DRUM REPLACE”
“MONOCHROME DRUM
REPLACE”
b
“CHANGE SUPPLIES”
L The drum cartridge life is finished. Replace the drum cartridge immediately.
Note:
L The continuous use of an old drum cartridge may cause malfunction. To
prevent this, when the drum life is finished, the unit will stop printing after a
while, and printing will not be possible until a new drum cartridge is
installed.
83
11. Help
Display
Cause & Solution
“COLOUR DRUM LIFE LOW”
“MONOCHROME DRUM LIFE
LOW”
b
“CHANGE SUPPLIES”
L The drum cartridge life is near its end. Replace the drum cartridge as soon
as possible.
“COOL DOWN FUSER”
L The unit is cooling down the fuser unit. Wait for a while.
“DIRECTORY FULL”
L There is no space to store new items in navigator directory. Erase
unnecessary items (page 45).
“DRUM NOT INSTALLED”
L The colour drum cartridge or the monochrome drum cartridge is not
installed. Install it (page 10).
“E-MAIL SIZE OVER”
L When performing scan to e-mail server, the total file size of scanned data
exceeded the file size limitation. Divide the document into sections.
“FAX IN MEMORY”
L The unit has a document in memory. See the other displayed message
instructions to print out the document. For fax memory capacity, see page
105.
L If feature #442 (page 64) is set to “ALWAYS”,
– check the connection between the computer and the unit.
– check the computer is turned ON.
“FILE SIZE OVER”
L When performing scan to FTP server, the total file size of scanned data
exceeded the file size limitation. Divide the document into sections.
“FRONT OR LEFT COVER
OPEN”
L The front or left cover is open. Close it.
“KEEP COPYING”
L Copying has stopped due to some existing problem (example: a lack of
recording paper or a recording paper jam). See the other displayed
message instructions to continue copying.
“LOW TEMP.”
L The inside of the unit is extremely cold and cannot be operated. Use the unit
in a warmer area.
“MEMORY FULL”
L When performing memory transmission, the document being stored
exceeded the memory capacity of the unit. Send the entire document
manually.
L When making a copy, the document being stored exceeded the memory
capacity of the unit. Press {Stop} to clear the message. Divide the
document into sections.
“MODEM ERROR”
L There is something wrong with the unit’s modem. Contact our service
personnel.
“NO FAX REPLY”
L The other party’s fax machine is busy or has run out of recording paper. Try
again.
“OUT OF PAPER INPUT TRAY
#1”
L Recording paper is not installed or the paper input tray has run out of paper.
Install paper (page 14, 29).
L Recording paper is not fed into the unit properly. Reinstall paper (page 14,
29).
Note:
L “#1”: Standard input tray
L “#2”: Optional input tray
L “#1+#2”: Standard input tray and optional input tray
“PAPER JAMMED”
84
L A recording paper jam occurred. See the other displayed message
instructions to remove the jammed paper (page 95).
11. Help
Display
Cause & Solution
“PC FAIL OR BUSY”
L The cable or the computer power cord is not connected correctly. Check the
connections (page 17, 25).
L The software is not running on the computer. Restart the software and try
again.
“PLEASE WAIT”
L The unit is warming up. Wait for a while.
“REDIAL TIME OUT”
L The other party’s fax machine is busy or has run out of recording paper. Try
again.
“REMOVE DOCUMENT”
L The document is jammed. Remove the jammed document (page 100).
L Attempted to send or copy a document longer than 600 mm (235/8") using
the automatic document feeder. Press {Stop} to remove the document.
Divide the document into two or more sheets and try again.
“RX MEMORY FULL”
L The memory is full of received documents due to a lack of recording paper
or a recording paper jam. Install paper (page 14) or remove the jammed
paper (page 95).
L If feature #442 (page 64) is set to “ALWAYS”,
– check the connection between the computer and the unit.
– check the computer is turned ON.
“SCANNER POSITION ERROR”
L There is something wrong with the scanner position. Turn the power switch
OFF, then ON. If the problem cannot be solved, contact our service
personnel.
“SELF CALIBRATION”
L The unit is changing the colour calibration. Wait for a while.
“TRANSMIT ERROR”
L A transmission error occurred. Try again.
“TONER CARTRIDGE NOT
INSTALLED”
L The toner cartridge is not installed. Install it (page 10).
“TRAY #2 LEFT COVER
OPEN”
L The left cover of the optional input tray is open. Close it.
“WASTE TONER FULL”
b
“CHANGE SUPPLIES”
L The waste toner cartridge life is near its end. Replace the waste toner
cartridge as soon as possible.
“WASTE TONER NOT
INSTALLED”
L The waste toner cartridge is not installed. Install it (page 9).
“WASTE TONER REPLACE”
b
“CHANGE SUPPLIES”
L The waste toner cartridge life is finished. Replace the waste toner cartridge
immediately (page 9, 107).
85
11. Help
Troubleshooting
11.3 When a function does not work
11.3.1 General
Problem
Cause & Solution
The unit does not work.
L Check the connections (page 17, 25).
The recording paper exit
becomes full quickly or the
recording paper does not
stack properly at the
recording paper exit.
L High humidity may cause the recording paper to curl. Try turning the paper
over and re-inserting it. If the curl on the paper is heavy, please remove it
from the recording paper exit. If you still have this problem, contact our
service personnel.
I cannot adjust the volume,
display items stored in onetouch dial and navigator
directory or display Caller
information.
L The unit is set to the scan mode or copy mode. Press {Fax} to switch
modes. If you still have this problem, contact our service personnel.
A printing error is displayed
while using PC FAX and
Remote Control.
L The printer driver is used for PC FAX and Remote Control. Transmission
errors will be displayed as printing errors.
Multi-Function Station does
not work properly.
L If you connect the USB cable to a USB hub, connect it to the USB port of
your computer directly.
L Make sure you have installed the latest Service Pack available for the
version of Windows installed on your computer. See the Microsoft web site
for details.
L If you have any other multifunction software installed on your computer,
uninstall it.
L Check that your computer has enough memory and hard disk space. If your
computer warns that there is insufficient memory, close other applications.
If there is not enough space on the hard disk, delete unnecessary files.
L Uninstall Multi-Function Station once, and re-install it.
I cannot install or uninstall
Multi-Function Station.
L Some of the files needed to install or uninstall Multi-Function Station may be
corrupted. Use the MfsCleaner utility (found on the supplied CD-ROM) to
solve the problem.
1. Insert the supplied CD-ROM into your CD-ROM drive.
L The setup program will start automatically.
2. [Tools] i [Cleanup Tool]
L The [MfsCleaner] window will appear.
3. Click [Clean], then click [Yes] to restart the computer.
Note:
L To install Multi-Function Station again, see page 24.
I cannot view the operating
instructions using MultiFunction Station.
86
L Install the operating instructions to your computer beforehand (page 25).
11. Help
Problem
Cause & Solution
I cannot find the unit in the
[Target Device] or [Device
Select] dialogue box when
operating the following
functions.
– Scanning
– Remote Control
– PC FAX
– Device Monitor
L The printer driver has not been installed. Install it on your computer (page
24).
I forgot the password for
feature programming via
remote operation.
L You may have changed the feature programming password. If you do not
remember it, assign a new password using feature #155 (page 58). When
required to enter the current password, enter “0101” instead.
11.3.2 Printing problems
Problem
Cause & Solution
I cannot print in
monochrome.
OR
I cannot print in colour.
L When using the unit as a printer, change the colour mode from the
[Quality] tab (page 28).
L When printing on envelopes, even if you press {Black}/{Colour}, the
printing colour will follow the colour mode setting.
L When using the unit as a copier;
– press {Black} to copy in monochrome.
– press {Colour} to copy in colour.
L When using the unit as a fax, sending/receiving colour faxes is not possible.
L One or more colour toner cartridge(s) is empty. Replace the toner cartridge
according to the displayed message. Even if cyan, magenta, yellow is
empty, monochrome printing is available.
Colour printing is too dark or
too light.
L Change the colour calibration (page 77).
Vertical, white lines appear
on the printed documents.
L The drum cartridge may be the cause. Print the colour test list, then clean
the drum cartridge (feature #480 on page 104).
The printing quality is poor
(e.g. has smudges, blurred
points or lines).
L Some paper has instructions recommending which side to print on. Try
turning the recording paper over.
L You may have used paper with a cotton and/or fibre content that is over
20 %, such as letterhead or resume paper.
L The recording paper is too damp. Use new paper.
ABC
I changed the recording
paper, but the printing quality
is still poor.
L The glass or rollers are dirty with correction fluid, etc. Clean them (page
101, 102). Please do not insert a document before correction fluid has dried
completely.
L The paper chute is dirty with toner, etc. Clean it (page 103).
L The toner save mode of feature #482 is ON (page 59).
L The unit may not be the cause. Print the printer test list to find out the
problem (page 104).
A blank sheet is ejected.
L You placed the document facing the wrong way when using the copier.
L The other party placed the document in their fax machine the wrong way.
Check with the other party.
87
11. Help
Problem
I cannot find the PCL driver.
Cause & Solution
L The PCL driver can be found in the following folder on the supplied CDROM.
Operating system
Folder path
Windows 98/Windows Me
“D:\Drivers\Object\Printer\Win98\PCL”
Windows 2000/Windows XP
Home/Windows Vista x32
“D:\Drivers\Object\Printer\x32\PCL”
Windows XP Professional x64
Edition/Windows Vista x64
“D:\Drivers\Object\Printer\x64\PCL”
(where “D” is the drive letter of your CD-ROM drive)
For more details, refer to:
http://panasonic.co.jp/pcc/cs/en/telecom/mfp-faq.htm
I specified automatic duplex
printing using the printer
driver, but documents are
printed on one side.
L Install the optional automatic duplex unit (page 80).
11.3.3 Scanner
Problem
Cause & Solution
I cannot scan.
L When scanning at a high resolution, a large amount of available memory is
required. If your computer warns that there is insufficient memory, close
other applications and try again.
L The unit is in use. Try again later.
L There is not enough space on the hard disk. Delete unnecessary files and
try again.
L Check the connection between the computer and the unit (page 17, 25).
L Restart the computer, and try again.
L You attempted to scan a document longer than the paper size which you
set. Change the setting or divide the document into the appropriate paper
size, and try again.
I cannot scan in
monochrome.
OR
I cannot scan in colour.
L To scan in monochrome, press {Black}. To scan in colour, press {Colour}.
The document is not fed into
the unit when using the unit
as a scanner.
L Remove the document in the automatic document feeder and re-insert it.
Even after clicking [Cancel],
scanning continues.
L Please wait. It may take a while for the cancel request to be accepted.
88
11. Help
Problem
The name of the desired
computer will not be
displayed on the unit when
scanning documents from
the unit (LAN connection
only).
Cause & Solution
L The printer driver has not been installed. Install it on your computer (page
24).
L The PC name list up feature has been set to [Off]. Set [PC name list up
on device] to [On] (page 27).
L The maximum number of computers on the LAN is connected to the unit (up
to 30 computers). Set [PC name list up on device] to [Off] on the other
computers (page 27).
L The IP address of the unit may have changed. To detect the IP address,
proceed as follows.
[Start] i [All Programs] or [Programs] i [Panasonic] i the
unit’s name i [IP Address Checker]
L The IP address for the unit will be detected.
11.3.4 Copier
Problem
Cause & Solution
The unit will not make a copy.
L You cannot make a copy during programming. Make the copy after
programming.
L The document was not fed into the unit properly. Re-insert the document.
L Recording paper is not installed or the unit has run out of paper. Install
paper (page 14).
Letters on the copied
documents are not clear.
L The original document is too dark or too light. Change the contrast (page
36) and try again.
The copied documents are
too dark and cannot be read.
L You used a coloured paper as a document. Change the contrast (page 36)
and make a lighter copy of the document, using “TEXT” resolution (page
36).
11.3.5 Fax
Problem
Cause & Solution
I cannot send documents.
L The telephone line cord is connected to the [EXT] jack on the unit. Connect
to the [LINE] jack (page 17).
L The other party’s fax machine is busy or has run out of recording paper. Try
again.
L The other party’s machine is not a fax machine. Check with the other party.
L The other party’s fax machine failed to answer the fax automatically. Send
the fax manually (page 43).
L Set the maximum fax speed to “14.4Kbps” (feature #418 on page 62).
I cannot send a fax overseas.
L Use the overseas transmission mode (feature #411 on page 61).
L Add two pauses at the end of the telephone number or dial manually.
The other party complains
that letters on their received
document are distorted.
L If your line has special telephone services such as call waiting, the service
may have been activated during fax transmission. Connect the unit to a line
that does not have these services.
L Another telephone on the same line is off the hook. Hang up the extension
telephone and try again.
The other party complains
about the quality of their
received documents.
L Try copying the document. If the copied image is clear, there may be
something wrong with the other party’s machine.
If the copied image is not clear, too dark, black and white lines or smudges
appear, refer to “11.3.2 Printing problems”, page 87.
L The original document is too dark or too light. Change the contrast (page
43) and try again.
89
11. Help
Problem
Cause & Solution
The other party complains
that received documents are
too dark and cannot be read.
L You used a coloured paper as a document. Change the contrast (page 36)
and make a lighter copy of the document, using “TEXT” resolution (page
36), and try again.
I cannot receive documents.
L You may have subscribed to a voice mail service due to service packs
offered by your telephone company. Fax reception may not be possible
when voice mail is activated so we recommend you to:
– contact your telephone company and request to deactivate voice mail
service, or
– subscribe to a Distinctive Ring service (page 55).
L The telephone line cord is connected to the [EXT] jack on the unit. Connect
to the [LINE] jack (page 17).
L Feature #442 is activated and the received fax documents are automatically
transferred to the computer. View the received documents using the
computer (page 52).
L Set the maximum fax speed to “14.4Kbps” (feature #418 on page 62).
I cannot receive documents
automatically.
L The receiving mode is set to TEL mode. Set to FAX ONLY mode. Press
{Fax Auto Answer} repeatedly to turn ON the {Fax Auto Answer} light.
L The time taken to answer the call is too long. Decrease the number of rings
before the unit answers a call (feature #210 on page 58).
L Make sure that the Distinctive Ring of feature #430 is set properly (page 55).
If you do not subscribe to the Distinctive Ring service offered by your local
telephone company, this feature should be OFF.
The display shows
“CONNECTING.....”, but
faxes are not received.
L The incoming call is not a fax. Set to TEL mode. Press {Fax Auto Answer}
repeatedly to turn OFF the {Fax Auto Answer} light.
The printing quality of the
received documents is poor.
L If documents can be copied properly, the unit is working normally. The other
party may have sent a faint document or there may be something wrong
with the other party’s machine. Ask them to send a clearer copy of the
document or to check their fax machine.
L If documents can not be copied properly, refer to “11.3.2 Printing problems”,
page 87.
The other party complains
that they cannot send a
document.
L The memory is full of received documents due to a lack of recording paper
or a recording paper jam. Install paper (page 14) or remove the jammed
paper (page 95).
L If feature #442 is set to “ALWAYS” (page 64), check the connection between
the computer and the unit.
L The unit is not in FAX ONLY mode. Press {Fax Auto Answer} repeatedly to
turn ON the {Fax Auto Answer} light.
I cannot select the desired
receiving mode.
L If you want to set FAX ONLY mode:
– press {Fax Auto Answer} repeatedly to turn ON the {Fax Auto
Answer} light.
L If you want to set TEL mode:
– press {Fax Auto Answer} repeatedly to turn OFF the {Fax Auto
Answer} light.
L The Distinctive Ring of feature #430 is activated (page 55).
When an extension telephone
is connected, I cannot receive
documents by pressing
{*}{#}{9}.
L You must set remote fax activation to ON (feature #434 on page 63)
beforehand.
L Press {*}{#}{9} firmly.
L You may have changed the remote fax activation code from {*}{#}{9}
(default setting). Verify the remote fax activation code (feature #434 on page
63).
90
11. Help
Problem
Cause & Solution
I cannot hear a dial tone.
L The telephone line cord is connected to the [EXT] jack on the unit. Connect
to the [LINE] jack (page 17).
L If you use a splitter/coupler to connect the unit, remove the splitter/coupler
and connect the unit to the wall jack directly. If the unit operates properly,
check the splitter/coupler.
L Disconnect the unit from the telephone line and connect a known working
telephone. If the working telephone operates properly, contact our service
personnel to have the unit repaired. If the working telephone does not
operate properly, contact your telephone company.
L The power cord or telephone line cord is not connected. Check the
connections (page 17).
L If you connected the unit through a computer modem, connect the unit
directly to a telephone line jack.
I cannot make calls.
L The dialing mode setting may be wrong. Change the setting (feature #120
on page 18).
The unit does not ring.
L The ringer volume is turned OFF. Adjust it (page 21).
The other party complains
they only hear a fax tone and
cannot talk.
L FAX ONLY mode is set (page 48). Tell the other party the number is only
used for faxes.
L If you use a Distinctive Ring service, make sure you have set the same ring
pattern assigned by the telephone company (page 55).
The {Redial} or {Pause}
button does not function
properly.
L If this button is pressed during dialing, a pause will be inserted. If pressed
immediately after a dial tone is obtained, the last number dialed will be
redialed.
The receiving mode does not
function properly.
L Distinctive Ring is set (feature #430 on page 55).
Whenever I try to retrieve my
voice mail messages, I am
interrupted by the fax tone.
L You are probably entering {*} {#} {9}. This is the default setting for the fax
activation code. If you use a voice mail service, turn the fax activation
feature OFF or reprogram the activation code (feature #434 on page 63).
I cannot receive a fax
document on the computer.
L Make sure the following features are set beforehand.
– PC fax reception (feature #442 on page 64)
– Computer setting for the PC fax reception (feature #443 on page 24)
91
11. Help
11.3.6 Network
Problem
I cannot operate the following
functions.
– PC printing
– Scanning
– Remote Control
– PC FAX
– Device Monitor
Cause & Solution
L Confirm the LED via the LAN port of the main board. If the LED is glowing
or blinking, the network access is working correctly.
If the LED is not glowing or blinking, confirm the LAN cable (category 5
straight cable) is connected to the LAN port of the main board correctly.
L If the LED is blinking and you cannot perform the desired operation, the IP
address of the unit may have changed.
To detect the IP address, proceed as follows.
[Start] i [All Programs] or [Programs] i [Panasonic] i the
unit’s name i [IP Address Checker]
L The IP address for the unit will be detected.
Note:
L If the IP address cannot be detected, enter it manually (feature #501 on
page 71). The IP address of the computer and the unit must be in the
same local IP address class as shown below. Set the IP address in the
range of the number specified in the class corresponding to your local
network scale.
Class
Subnet mask
IP address
Class A
255.0.0.0
10.0.0.1 10.255.255.254
Class B
255.255.0.0
172.xx.0.1 172.xx.255.254*1
Class C
255.255.255.0
192.168.xx.1 192.168.xx.254*2
*1 “xx” should be the same value for the unit and for the computer, as
shown in the following example.
Example: 172.16.0.1 - 172.16.255.254
(The available range of “xx” is 16 - 31)
*2 “xx” should be the same value for the unit and for the computer, as
shown in the following example.
Example: 192.168.0.1 - 192.168.0.254
(The available range of “xx” is 0 - 255)
L Your firewall software is blocking the connection. Disable the firewall
software or change the firewall settings to make the Multi-Function Station
work properly.
L LAN features can be used when the unit and the computer are connected in
same network segment only. Make sure the network is configured correctly.
Consult your network administrator.
The unit does not appear in
the [Select a Network Device]
dialogue box when installing
Multi-Function Station.
92
L Your firewall software is blocking the connection and the setup program may
not list any units. Consult your network administrator and temporarily
disable the firewall software.
L The unit is connected to another network segment and the setup program
may not list any units. Make sure the network is configured correctly.
Consult your network administrator.
11. Help
Problem
The [Windows Security Alert]
dialogue box appears and
asks if I want to block
[PCCMFLPD] and I cannot
operate the following
functions after installing the
Microsoft Windows XP
Service Pack 2.
– PC printing
– Scanning
– Remote Control
– PC FAX
– Device Monitor
Cause & Solution
L Click [Keep Blocking] and run the Windows Firewall Setting Tool to allow
the data transmission for Multi-Function Station (page 93).
11.3.7 Using an answering machine
Problem
Cause & Solution
I cannot receive documents
automatically.
L Your greeting message on the answering machine is too long. Shorten the
message. Record a message up to 10 seconds long.
L The answering machine rings too many times. Set to 1 or 2 rings.
I cannot receive voice
messages.
L Check if the answering machine is turned ON and connected to the unit
properly (page 50).
L Set the number of rings on the answering machine to 1 or 2.
I pressed the remote access
code to access the answering
machine remotely, but the line
was disconnected.
L The code may include “#” which is used for certain features provided by
telephone companies. Change the code on the answering machine to
another number which does not include “#”.
Callers complain that they
cannot send a document.
L There is no room left in memory of your answering machine to record voice
messages. See the operating instructions of the answering machine and
erase unnecessary messages.
L You set the answering machine to only give a greeting message.
11.3.8 If a power failure occurs
L The unit will not function.
L If any documents are stored in the memory (i.e. during copy, PC printing, fax transmission or fax reception), they
will be lost.
L The unit is not designed for making emergency telephone calls when the power fails. Alternative arrangements
should be made for access to emergency services.
L Fax transmission and reception will be interrupted.
L When power is restored, a power down report will be printed out stating which fax items in the memory have been
erased.
11.3.9 Firewall setting tool for Microsoft Windows XP Service Pack 2/Windows Vista users
(LAN connection only)
After installing Microsoft Windows XP Service Pack 2/Windows Vista, you will not be able to use the following
functions because the Windows Firewall feature will be activated and block the connection.
– Device Monitor
– LPD Manager (Network communication tool)
The Windows Firewall Setting Tool enables you to change the Windows Firewall security settings and to use the above
functions properly.
1 Insert the CD-ROM that is supplied with the unit into your CD-ROM drive.
93
11. Help
L If the [Select Language] dialogue box appears, select the desired language that you want to use with this
software. Click [OK].
2 [Tools] i [Windows Firewall Setting]
L The [Windows Firewall Setting Tool] window will appear.
3 [Add to the exceptions list] i [OK] i [OK]
To confirm the security settings (For Windows XP users)
1. [Start] i [Control Panel] i [Security Center]
L The [Windows Security Center] window will appear.
2. [Windows Firewall]
L The [Windows Firewall] dialogue box will appear.
3. Click the [Exceptions] tab.
4. Confirm that [Panasonic Trap Monitor Service] and [PCCMFLPD] are displayed and checked on the
[Programs and Services] list.
To confirm the security settings (For Windows Vista users)
1. [Start] i [Control Panel] i [Security Center]
L The [Windows Security Center] window will appear.
2. [Windows Firewall]
L The [Windows Firewall] dialogue box will appear.
3. [Change settings]
L The [User Account Control] dialogue box will appear.
4. [Continue]
5. Click the [Exceptions] tab.
6. Confirm that [Panasonic Trap Monitor Service], [PCMFSMLM] and [PCCMFLPD] are displayed and checked
on the [Program or port] list.
11.3.10 Notice for KX-MB200/KX-MB700/KX-FLB880 series users
If you have already installed KX-MB200/KX-MB700/KX-FLB880 series Multi-Function Station on your computer, the
instructions of modifying or adding printer driver change after installing KX-MC6000 series Multi-Function Station.
You can modify or add printer driver, as follows.
1 Start Windows and insert the KX-MB200/KX-MB700/KX-FLB880 series CD-ROM into your CD-ROM drive.
L If the [Select Language] dialogue box appears, select the desired language that you want to use with this
software. Click [OK].
2 [Easy installation]
3 [Modify] i [Next]
4 Select [Modify Utility] or [Add Printer Driver]. i [Next]. Then follow the on-screen instructions.
Important:
L For users of versions prior to 1.12, download the latest software as follows, then activate it.
[Start] i [All Programs] or [Programs] i [Panasonic] i the unit’s name i [Support Web
Page]. Then follow the on-screen instructions.
94
12. Paper Jams
12 Paper Jams
Jams
12.1 Recording paper jam
1 Push the left cover open lever (1) upward, then pull
open the left cover (2).
1
Caution:
L Do not pull out the jammed paper forcibly before
opening the left cover.
2
L Do not open the paper input tray as the jammed
paper may be pulled and the jam may get worse.
3
4
Caution:
L During or immediately after printing,
the fuser unit (3) gets hot. Wait until
the fuser unit cools down before
removing the jammed paper.
Note:
L Do not touch the rollers (4).
12.1.1 When the recording paper has
jammed inside of the unit
The display will show the following.
“PAPER JAMMED”
b
“OPEN LEFT COVER HOT CAUTION”
95
12. Paper Jams
2 Remove the jammed paper.
Case 1:
When the recording paper has jammed near the
rollers:
Case 2:
When the recording paper has jammed near the
fuser unit:
1. Lift both green levers (6) until they stop.
1. Remove the jammed paper (5) carefully by pulling it
toward you.
5
6
2. Close the left cover.
2. Remove the jammed paper (7) carefully by pulling it
toward you.
Example 1:
7
Example 2:
7
96
12. Paper Jams
3. Push back the green levers (8) to the original
position.
Case 3:
When the recording paper has jammed inside of the
optional automatic duplex unit:
1. Close the left cover.
8
4. Close the left cover.
2. Open the automatic duplex unit cover (9).
9
3. When the document has jammed near the roller:
Hold the automatic duplex unit cover and remove the
jammed paper (j) carefully by pulling it upward.
j
97
12. Paper Jams
When the document has jammed near the
recording paper exit of the automatic duplex unit:
Hold the automatic duplex unit cover and remove the
jammed paper (k) carefully by pulling it toward you.
12.1.2 When the recording paper has
jammed near the optional input tray
The display will show the following.
“PAPER JAMMED”
b
“OPEN TRAY #2 LEFT COVER”
1 Open the cover (1) at the left side of the optional
input tray.
k
4. Close the automatic duplex unit cover.
1
2 Remove the jammed paper (2).
2
98
12. Paper Jams
3 Close the cover at the left side of the optional input
tray.
12.1.3 When the recording paper is not fed
into the unit properly
The display will show the following.
– “CHECK PICK UP INPUT TRAY #1” (standard
input tray)
– “CHECK PICK UP INPUT TRAY #2” (optional input
tray)
1 Pull the paper input tray until it clicks into place, then
pull it completely out, lifting the front part of the tray.
Remove the recording paper and straighten.
2 Re-load the recording paper.
Standard input tray:
Optional input tray:
3 Insert the paper input tray to the unit, lifting the front
part of the tray. Then push it completely into the unit.
Note:
L If the error message is still displayed, check the
recording paper specifications and re-install
recording paper. See page 14 and page 80 for
details.
99
12. Paper Jams
2 Remove the jammed document (3) carefully.
12.2 Document jams (Automatic
document feeder)
When the document has jammed near the
document entrance:
3
Caution:
L Do not pull out the jammed document forcibly
before lifting the ADF cover.
When the document has jammed near the
document exit:
1 Open the ADF cover (1) while holding the
3
document cover (2).
1
2
3 Close the ADF cover.
100
13. Cleaning
3 Close the document cover (5).
13 Cleaning
Cleaning
13.1 Cleaning the white plates
and glass
5
Clean the white plates and glass when a black line, a
white line or a dirty pattern appears on:
– your recording paper,
– the original document,
– the scanned data, or
– the fax document received by the other party.
Caution:
L Do not use paper products, such as paper towels
or tissues for cleaning.
1 Open the document cover (1).
1
2 Hold the document cover (2) while cleaning the
white plates (3) and the scanner glass (4).
2
3
4
101
13. Cleaning
4 Close the ADF cover.
13.2 Cleaning the document
feeder rollers
Clean the rollers when the document frequently
misfeeds.
Caution:
L Do not use paper products, such as paper towels
or tissues for cleaning.
1 Turn the power switch OFF.
2 Open the ADF cover (1) while holding the
document cover (2).
1
2
3 Clean the document feeder rollers (3) with a cloth
moistened with water, and let all parts dry
thoroughly.
3
102
5 Turn the power switch ON.
13. Cleaning
3 Clean the paper chute (5) with a dry paper towel or
13.3 Cleaning the paper chute
tissue.
Clean the paper chute inside the unit when a line or a
dirty pattern appears at the top or bottom of your
recording paper.
1 Turn the power switch OFF.
2 Push the left cover open lever (1) upward, then pull
open the left cover (2).
1
5
6
2
Note:
L Do not touch the black belt (6), or rub it strongly.
4 Close the left cover.
3
4
Caution:
L During or immediately after printing,
the fuser unit (3) gets hot. Wait until
the fuser unit cools down before
removing the jammed paper.
5 Turn the power switch ON.
Note:
L Do not touch the rollers (4).
103
14. General Information
14 General
Printed
Repor
Information
ts
14.1 Reference lists and reports
You can print out the following lists and reports for your
reference.
– “SETUP LIST”
– “TEL NO. LIST”
– “JOURNAL REPORT”
– “BROADCAST LIST”
– “PRINTER TEST”
– “COLOUR TEST”
– “CALLER’S LIST”
– “PCL FONT LIST”
– “ADDRESS LIST”
– “FTP SERVER LIST”
{Menu}
{Set} {<}{>}
1 Press {Menu} repeatedly to display “PRINT
REPORT”.
2 Press {<} or {>} repeatedly to display the desired
item.
3 Press {Set} to start printing. i {Menu}
Colour test list
The unit will print a colour test list consisting of black,
cyan, magenta and yellow lines so you can specify which
drum cartridge has the problem.
If vertical, white lines appear on the colour test list, try
the following to solve the problem.
Solution 1: Cleaning the drum cartridge
Important:
L This solution uses at least 3 pages of recording
paper. Make sure there is enough recording
paper installed in the standard input tray
beforehand.
1. {Menu} i {#}{4}{8}{0}
2. Select the colour which has vertical, white lines in the
colour test list.
{1} “BLACK” (default)
{2} “CYAN”
{3} “MAGENTA”
{4} “YELLOW”
3. {Set}
L The drum cartridge will be cleaned automatically
by printing out 3 pages of the selected colour.
Repeat steps 1 to 3 for all lines with vertical, white
lines.
104
L Print the colour test list again. If the vertical, white
lines remain, try the next solution.
Solution 2: Changing the drum cartridge
L If the black line has vertical, white lines, change the
monochrome drum cartridge.
L If the cyan, magenta or yellow line has vertical, white
lines, change the colour drum cartridge.
L Print the colour test list again. If the vertical, white
lines remain, contact our service personnel.
14. General Information
Specifications
14.2 Specifications
■ Applicable lines:
Public Switched Telephone Network
■ Document size:
Max. 216 mm (81/2") in width, Max. 600 mm (235/8") in
length
■ Effective scanning width:
208 mm (83/16")
■ Effective printing width:
Letter/Legal: 208 mm (83/16")
A4: 202 mm (715/16")
■ Transmission time*1:
Approx. 4 s/page (ECM-MMR Memory transmission)*2
■ Scanning density:
Scanning resolution:
Up to 600 × 1,200 dpi (Optical)
Up to 9,600 × 9,600 dpi (Interpolated)
Copy resolution:
Up to 600 × 600 dpi
Fax resolution:
Horizontal: 8 pels/mm (203 pels/inch)
Vertical: 3.85 lines/mm (98 lines/inch)-in standard
resolution,
7.7 lines/mm (196 lines/inch)-in fine/photo
resolution,
15.4 lines/mm (392 lines/inch)-in super fine
resolution
■ Photo resolution:
64-level
■ Scanner type:
Colour Contact Image Sensor
■ Printer type:
Laser Printer
■ Data compression system:
Modified Huffman (MH), Modified READ (MR), Modified
Modified READ (MMR)
■ Modem speed:
33,600 / 31,200 / 28,800 / 26,400 / 24,000 / 21,600 /
19,200 / 16,800 / 14,400 / 12,000 / 9,600 / 7,200 / 4,800
/ 2,400 bps; Automatic Fallback
■ Operating environment:
10 °C – 32.5 °C (50 °F – 90.5 °F), 20 % – 80 % RH
(Relative Humidity)
■ Dimensions:
Approx. width 520 mm × depth 438 mm × height 546 mm
(201/2" × 171/4" × 211/2")
■ Mass (Weight):
Approx. 30 kg (67 lb)
■ Power consumption:
Standby: Approx. 15 W
Preheat: Approx. 35 W
Copy: Approx. 550 W
Maximum: Approx. 1,000 W (When the fuser lamp turns
on)
■ Power supply:
120 V AC, 60 Hz
■ Memory capacity
(for operation and storing memory):
192 MB
■ Fax memory capacity:
10 MB in total
Approx. 630 pages of memory reception
(max. 255 pages per one reception)
Approx. 150 pages of memory transmission
(Based on the ITU-T No. 1 Test Chart in standard
resolution, without using the Error Correction Mode.)
■ Scan to e-mail server memory capacity:
5 MB in total (including the e-mail message)
■ Scan to FTP server memory capacity:
20 MB in total
■ Laser diode properties:
Laser output: Max. 6.5 mW
Wave length: 770 nm – 800 nm
Emission duration: Continuous
■ Print speed:
Colour:
Letter: Approx. 21 ppm (pages per minute)
A4: Approx. 20 ppm (pages per minute)
B/W:
Letter: Approx. 21 ppm (pages per minute)
A4: Approx. 20 ppm (pages per minute)
■ Printing resolution:
Up to 1,200 × 1,200 dpi
*1 Transmission speed depends on the contents of the
pages, resolution, telephone line conditions and
capability of the other party’s machine.
*2 Transmission speed is based on the ITU-T No. 1 Test
Chart with original mode. If the capability of the other
party’s machine is inferior to your unit, the
transmission time may be longer.
ITU-T No.1 Test Chart
Note:
L Design and specifications are subject to change
without notice.
L The pictures and illustrations in these instructions
may vary slightly from the actual product.
L The accuracy of the clock is approximately ±60
seconds a month.
105
14. General Information
Recording paper specifications
Plain paper/Thin paper:
Letter: 216 mm × 279 mm (81/2" × 11")
Legal: 216 mm × 356 mm (81/2" × 14")
A4: 210 mm × 297 mm (81/4" × 1111/16")
Thick paper/Transparency/Label/Card stock size:
Letter: 216 mm × 279 mm (81/2" × 11")
A4: 210 mm × 297 mm (81/4" × 1111/16")
Envelope size:
#10: 105 mm × 241 mm (41/8" × 91/2")
DL: 110 mm × 220 mm (45/16" × 85/8")
Recording paper weight:
60 g/m2 to 165 g/m2 (16 lb to 44 lb)
Card stock weight:
163 g/m2 (90 lb)
Note for recording paper:
L We recommend that you test paper (especially
special sizes and types of paper) on the unit before
purchasing large quantities.
L Do not use the following types of paper:
– Paper with cotton and/or fibre content that is over
20 %, such as letterhead paper or paper used for
resumes
– Extremely smooth or shiny paper, or paper that is
highly textured
– Coated, damaged or wrinkled paper
– Paper with foreign objects attached, such as tabs
or staples
– Paper that has dust, lint or oil stains
– Paper that will melt, vaporize, discolour, scorch or
emit dangerous fumes near 200 °C (392 °F),
such as vellum paper. These materials may
transfer onto the fusing roller and cause damage.
– Moist paper
– Inkjet paper
L Some paper is designed to be printed on only one
side. Try printing on the other side of the paper if you
are not happy with the print quality, or if misfeeding
occurs.
L For proper paper feeding and best print quality, we
recommend using long-grained paper.
L Do not use paper of different types or thicknesses at
the same time. This may cause paper jams.
L Do not use paper printed from this unit for doublesided printing with other copiers or printers. This may
cause paper jams.
L To avoid curling, do not open paper packs until you
are ready to use the paper. Store unused paper in
the original packaging, in a cool and dry location.
Toner life
Toner life depends on the amount of content in a printed
document. The following is the approximate relationship
between coverage and toner life for replacement toner
cartridge. Toner life varies in actual usage.
L The following number of sheets and image sample is
for when printing in one colour. As actual colour
printing is a combination of several colours, the
number of sheets will vary depending on the
contents of the original document.
5 % coverage
Approx. 2,000 sheets of
letter-size paper using:
– KX-FATC501A
– KX-FATM502A
– KX-FATY503A
Approx. 2,500 sheets using:
– KX-FATK504A
Approx. 4,000 sheets using:
– KX-FATC506A
– KX-FATM507A
– KX-FATY508A
– KX-FATK509A
10 % coverage
Approx. 1,000 sheets of
letter-size paper using:
– KX-FATC501A
– KX-FATM502A
– KX-FATY503A
Approx. 1,250 sheets using:
– KX-FATK504A
Approx. 2,000 sheets using:
– KX-FATC506A
– KX-FATM507A
– KX-FATY508A
– KX-FATK509A
15 % coverage
Approx. 650 sheets of lettersize paper using:
– KX-FATC501A
– KX-FATM502A
– KX-FATY503A
Approx. 800 sheets using:
– KX-FATK504A
Approx. 1,400 sheets using:
– KX-FATC506A
– KX-FATM507A
– KX-FATY508A
– KX-FATK509A
Table of Contents1.
1. Table of Contents 1. Introduction and Installation Accessories
1.1 Included accessories.1.2 Accessory information.Finding the Controls
1.3 Description of buttons.1.4 Overview Installation
1.5 Toner cartridge and drum unit
1.6 Document tray 1.7 Output tray1.8 Recording paper2. Preparation
2.1 Connections 2.2 Turning the power switch ON Help Button2.3 Help function Volume
2.4 Adjusting volume Initial Programming 2.5 Dialing mode 2.6 Date and time.
2.7 Your logo.2.8 Your fax number 3. Copy / Copying3.1 Using the unit as a copy machine.
3.2 Making a copy 3.3 More copying features
4. PC Operations/ Setup 4.1 Connecting to a computer
4.2 Installing Multi-Function Station 4.3 Starting Multi-Function Station Printing
4.4 Using the unit as a printer Scanning 4.5 Using the unit as a scannerRemote Control
4.6 Operating the unit from your computer.
4.7 Fax sending/receiving using Multi-Function Station
4.8 Registering the computer in the LANnetwork with the optional LAN board
4.9 Confirming the status of the unit 5. Case / Setup
5.1 Selecting the way to use your unit 5.2 Case 1: FAX ONLY
5.3 Case 2a: Distinctive Ring (1 phone line with 2 or more phone numbers)
5.4 Case 2b: Distinctive Ring (using withvoice mail service)
5.5 Case 3: EXT. TAM (External Telephone Answering Machine)
Table of Contents2.
1. Table of Contents
1.1 Included accessories.1.2 Accessory information.Finding the Controls
1.3 Description of buttons.1.4 Overview Installation1.5 Toner cartridge and drum unit
1.6 Document tray 1.7 Output tray1.8 Recording paper2. Preparation
2.1 Connections 2.2 Turning the power switch ON Help Button2.3 Help function Volume
2.4 Adjusting volume Initial Programming 2.5 Dialing mode 2.6 Date and time.
2.7 Your logo.2.8 Your fax number 3. Copy / Copying
3.1 Using the unit as a copy machine.
Thank you for purchasing a Panasonic fax machine.
Things you should keep a record of
Attach your sales receipt here.
For your future reference
Date of purchase
Serial number (found on the rear of the unit)
Dealer's name and address
Dealer's telephone number
Table of Contents1.
1. Table of Contents / Introduction and Installation Accessories
1.1 Included accessories.
1.2 Accessory information.Finding the Controls
1.3 Description of buttons.
1.4 Overview Installation
1.5 Toner cartridge and drum unit
1.6 Document tray
1.7 Output tray
1.8 Recording paper
2. Preparation
2.1 Connections
2.2 Turning the power switch ON Help Button
2.3 Help function Volume
2.4 Adjusting volume Initial Programming
2.5 Dialing mode
2.6 Date and time.
2.7 Your logo.
2.8 Your fax number
3. Copy / Copying
3.1 Using the unit as a copy machine.
3.2 Making a copy
3.3 More copying features
4. PC Operations/ Setup 4.1 Connecting to a computer
4.2 Installing Multi-Function Station 4.3 Starting Multi-Function Station Printing
4.4 Using the unit as a printer Scanning 4.5 Using the unit as a scannerRemote Control
4.6 Operating the unit from your computer.
4.7 Fax sending/receiving using Multi-Function Station
Thank you for purchasing a Panasonic fax machine.
Things you should keep a record of
Attach your sales receipt here.
For your future reference
Date of purchase
Serial number (found on the rear of the unit)
Dealer's name and address
Dealer's telephone number
Table of Contents1.
1. Table of Contents / Introduction and Installation Accessories
1.1 Included accessories.
1.2 Accessory information.Finding the Controls
1.3 Description of buttons.
1.4 Overview Installation
1.5 Toner cartridge and drum unit
1.6 Document tray
1.7 Output tray
1.8 Recording paper
2. Preparation
2.1 Connections
2.2 Turning the power switch ON Help Button
2.3 Help function Volume
2.4 Adjusting volume Initial Programming
2.5 Dialing mode
2.6 Date and time.
Thank you for purchasing a Panasonic fax machine.
Things you should keep a record of
Attach your sales receipt here.
For your future reference
Date of purchase
Serial number (found on the rear of the unit)
Dealer's name and address
Dealer's telephone number
Note:
L The coverage changes with the depth, thickness and
size of the characters.
106
14. General Information
L If you turn on the toner save feature, the toner
cartridge will last approx. 40 % longer.
Drum life
The drum cartridge needs to be replaced regularly.
There are various factors that determine the actual drum
life, such as temperature, humidity, type of paper and
how much toner you use for the number of sheets per
print job. The maximum drum life is approx. 10,000
sheets. The actual number of sheets your drum will print
may be significantly less than this estimate if your unit is
often used for printing small number sheets per job.
Because many of the factors that determine the actual
drum life cannot be controlled, we cannot guarantee a
minimum number of sheets that will be printed by your
drum.
Note:
L The continuous use of an old drum cartridge may
cause malfunction. To prevent this, when the drum
life is finished, the unit will stop printing after a while,
and printing will not be possible until a new drum
cartridge is installed.
Waste toner cartridge life
The waste toner cartridge needs to be replaced
regularly. The maximum waste toner cartridge life is
approx. 32,000 sheets with 5 % coverage for
monochrome printing and approx. 8,000 sheets with 5 %
cyan, magenta, yellow and black coverage for colour
printing. The actual number of sheets may significantly
vary depending on the contents of the original
document.
Waste disposal method
Waste material should be disposed of under conditions
which meet all national and local environmental
regulations.
107
14. General Information
Copyrights
14.3 Information of copyrights and licences
L This product uses a part of NetBSD kernel.
The use of a part of NetBSD kernel is based on the typical BSD style licence below.
Copyright (c)
The Regents of the University of California. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted
provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and
the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions
and the following disclaimer in the documentation and/or other materials provided with the
distribution.
3. All advertising materials mentioning features or use of this software must display the following
acknowledgement:
This product includes software developed by the University of California, Berkeley and its
contributors.
4. Neither the name of the University nor the names of its contributors may be used to endorse or
promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
However, parts of the NetBSD Kernel are provided with the following copyright notices.
Copyright (c) 1980, 1983, 1988, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1980, 1986, 1989, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1980, 1986, 1991, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1980, 1986, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1985, 1986, 1988, 1993, 1994 The Regents of the University of California. All rights
reserved.
Copyright (c) 1982, 1986, 1988, 1990, 1993 The Regents of the University of California. All rights
reserved.
Copyright (c) 1982, 1986, 1988, 1990, 1993, 1994, 1995 The Regents of the University of California. All
rights reserved.
Copyright (c) 1982, 1986, 1988, 1990, 1993, 1995 The Regents of the University of California. All rights
reserved.
Copyright (c) 1982, 1986, 1988, 1991, 1993 The Regents of the University of California. All rights
reserved.
Copyright (c) 1982, 1986, 1988, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1986, 1988, 1993, 1995 The Regents of the University of California. All rights
reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights
reserved.
Copyright (c) 1982, 1986, 1989, 1993 The Regents of the University of California. All rights reserved.
108
14. General Information
Copyright (c) 1982, 1986, 1990, 1991, 1993 The Regents of the University of California. All rights
reserved.
Copyright (c) 1982, 1986, 1990, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1986, 1990, 1993, 1994 The Regents of the University of California. All rights
reserved.
Copyright (c) 1982, 1986, 1991, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1986, 1991, 1993, 1994 The Regents of the University of California. All rights
reserved.
Copyright (c) 1982, 1986, 1991, 1993, 1995 The Regents of the University of California. All rights
reserved.
Copyright (c) 1982, 1986, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1986, 1993, 1994 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1986, 1993, 1994, 1995 The Regents of the University of California. All rights
reserved.
Copyright (c) 1982, 1986, 1993, 1995 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1988, 1991, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1983, 1990, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1983, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1985, 1986, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1985, 1986, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1986, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1987, 1991, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1987, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1987, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1988 Regents of the University of California. All rights reserved
Copyright (c) 1988 Stephen Deering.
Copyright (c) 1988 University of Utah.
Copyright (c) 1988, 1989, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1988, 1991, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1988, 1992, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1988, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1989 The Regents of the University of California. All rights reserved.
Copyright (c) 1989, 1991, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1989, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1989, 1993, 1994 The Regents of the University of California. All rights reserved.
Copyright (c) 1990, 1991, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1990, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1991, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1991, 1993, 1994 The Regents of the University of California. All rights reserved.
Copyright (c) 1992 Regents of the University of California. All rights reserved.
Copyright (c) 1992, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1993 Adam Glass
Copyright (C) 1993 by Sun Microsystems, Inc. All rights reserved.
Copyright (c) 1994 Gordon W. Ross
Copyright (c) 1994 Winning Strategies, Inc. All rights reserved.
Copyright (c) 1995 The Regents of the University of California. All rights reserved.
Copyright (C) 1995, 1996, 1997, and 1998 WIDE Project. All rights reserved.
Copyright (c) 1996 The Regents of the University of California. All rights reserved.
Copyright (c) 1996 John S. Dyson All rights reserved.
Copyright (c) 1996 Matt Thomas. All rights reserved.
Copyright (c) 1996 Matthew R. Green. All rights reserved.
Copyright (c) 1996 Paul Kranenburg
Copyright (c) 1996, 1997, 1999, 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1996, 2000 Christopher G. Demetriou. All rights reserved.
109
14. General Information
Copyright (c) 1996,1999 by Internet Software Consortium.
Copyright (c) 1996-1999 by Internet Software Consortium.
Copyright (c) 1997 Jonathan Stone and Jason R. Thorpe. All rights reserved.
Copyright (c) 1997 Christos Zoulas. All rights reserved.
Copyright (c) 1997 Manuel Bouyer. All rights reserved.
Copyright (c) 1997, 1998 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1997, 1998, 1999, 2000 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1997, 1998, 1999, 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1997, 1998, 1999, 2002 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1997, 1998, 2000, 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1997, 1998, 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1997,98 The NetBSD Foundation, Inc. All rights reserved.
Copyright (C) 1997-2000 Sony Computer Science Laboratories Inc. All rights reserved.
Copyright (c) 1997-2002 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1998 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1998 Todd C. Miller <Todd.Miller@courtesan.com> All rights reserved.
Copyright (c) 1998, 1999 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1998, 1999, 2000 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1998, 1999, 2000, 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1998, 2000 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1998, 2000, 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1999 The NetBSD Foundation, Inc. All rights reserved.
Copyright (C) 1999 WIDE Project. All rights reserved.
Copyright (c) 1999, 2000 Jason L. Wright (jason@thought.net) All rights reserved.
Copyright (c) 1999, 2000 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1999, 2000, 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1999, 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 2000 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 2000, 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 2000, 2001, 2002 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 2002 The NetBSD Foundation, Inc. All rights reserved.
Copyright 1998 Massachusetts Institute of Technology. All rights reserved.
Copyright 2001 Wasabi Systems, Inc. All rights reserved.
Portions Copyright (c) 1993 by Digital Equipment Corporation.
Portions Copyright (c) 1995 by International Business Machines, Inc.
Copyright (c) 1983, 1989 The Regents of the University of California. All rights reserved.
Copyright (c) 1996 by Internet Software Consortium. All rights reserved.
Copyright (c) 1980, 1986, 1989 Regents of the University of California. All rights reserved.
Copyright (c) 1988 The Regents of the University of California. All rights reserved.
Copyright (c) 1992, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1994 Christopher G. Demetriou. All rights reserved.
Copyright (c) 1997 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1999 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1996 Gardner Buchanan <gbuchanan@shl.com> All rights reserved.
Parts of the NetBSD Kernel are provided with the licences that are slightly different from the above Berkeley-formed
licence. Please refer the source code of the NetBSD Kernel about the details.
The source code of the NetBSD Kernel is provided by the NetBSD CVS Repositories
(http://cvsweb.netbsd.org/bsdweb.cgi/), and this product includes parts of the source code in the following directories.
http://cvsweb.netbsd.org/bsdweb.cgi/src/sys/kern/
http://cvsweb.netbsd.org/bsdweb.cgi/src/sys/net/
http://cvsweb.netbsd.org/bsdweb.cgi/src/sys/netinet/
110
14. General Information
L This product contains Net-SNMP software and is using it based on the following licence conditions.
---- Part 1: CMU/UCD copyright notice: (BSD like) ----Copyright 1989, 1991, 1992 by Carnegie Mellon University
Derivative Work - 1996, 1998-2000
Copyright 1996, 1998-2000 The Regents of the University of California
All Rights Reserved
Permission to use, copy, modify and distribute this software and its documentation for any purpose and
without fee is hereby granted, provided that the above copyright notice appears in all copies and that
both that copyright notice and this permission notice appear in supporting documentation, and that the
name of CMU and The Regents of the University of California not be used in advertising or publicity
pertaining to distribution of the software without specific written permission.
CMU AND THE REGENTS OF THE UNIVERSITY OF CALIFORNIA DISCLAIM ALL WARRANTIES
WITH REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL CMU OR THE REGENTS OF THE
UNIVERSITY OF CALIFORNIA BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL
DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM THE LOSS OF USE, DATA OR
PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS
ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS
SOFTWARE.
---- Part 2: Networks Associates Technology, Inc copyright notice (BSD) ----Copyright (c) 2001-2003, Networks Associates Technology, Inc
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided
that the following conditions are met:
* Redistributions of source code must retain the above copyright notice, this list of conditions and the
following disclaimer.
* Redistributions in binary form must reproduce the above copyright notice, this list of conditions and
the following disclaimer in the documentation and/or other materials provided with the distribution.
* Neither the name of the Networks Associates Technology, Inc nor the names of its contributors may
be used to endorse or promote products derived from this software without specific prior written
permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS ``AS IS''
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
111
14. General Information
---- Part 3: Cambridge Broadband Ltd. copyright notice (BSD) ----Portions of this code are copyright (c) 2001-2003, Cambridge Broadband Ltd.
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided
that the following conditions are met:
* Redistributions of source code must retain the above copyright notice, this list of conditions and the
following disclaimer.
* Redistributions in binary form must reproduce the above copyright notice, this list of conditions and
the following disclaimer in the documentation and/or other materials provided with the distribution.
* The name of Cambridge Broadband Ltd. may not be used to endorse or promote products derived
from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDER ``AS IS'' AND ANY EXPRESS OR
IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
EVENT SHALL THE COPYRIGHT HOLDER BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
---- Part 4: Sun Microsystems, Inc. copyright notice (BSD) ----Copyright © 2003 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara,
California 95054, U.S.A. All rights reserved.
Use is subject to licence terms below.
This distribution may include materials developed by third parties.
Sun, Sun Microsystems, the Sun logo and Solaris are trademarks or registered trademarks of Sun
Microsystems, Inc. in the U.S. and other countries.
Redistribution and use in source and binary forms, with or without modification, are permitted provided
that the following conditions are met:
* Redistributions of source code must retain the above copyright notice, this list of conditions and the
following disclaimer.
* Redistributions in binary form must reproduce the above copyright notice, this list of conditions and
the following disclaimer in the documentation and/or other materials provided with the distribution.
* Neither the name of the Sun Microsystems, Inc. nor the names of its contributors may be used to
endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS ``AS IS''
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE
112
14. General Information
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Also this product contains software which includes following notices and licences.
/***********************************************************
Copyright 1988, 1989, 1990 by Carnegie Mellon University
Copyright 1989 TGV, Incorporated
All Rights Reserved
Permission to use, copy, modify, and distribute this software and its documentation for any purpose and
without fee is hereby granted, provided that the above copyright notice appear in all copies and that
both that copyright notice and this permission notice appear in supporting documentation, and that the
name of CMU and TGV not be used in advertising or publicity pertaining to distribution of the software
without specific, written prior permission.
CMU AND TGV DISCLAIMS ALL WARRANTIES WITH REGARD TO THIS SOFTWARE, INCLUDING
ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS, IN NO EVENT SHALL CMU OR
TGV BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR ANY
DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN
AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR
IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
******************************************************************/
L This product contains NetBSD software and is using it based on the following licence conditions.
/** Copyright (c) 1990 The Regents of the University of California.
* All rights reserved.
*
* This code is derived from software contributed to Berkeley by Chris Torek.
*
* Redistribution and use in source and binary forms, with or without modification, are permitted provided
* that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the
* following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and
* the following disclaimer in the documentation and/or other materials provided with the distribution.
* 3. Neither the name of the University nor the names of its contributors may be used to endorse or
* promote products derived from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND ANY
* EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY
* DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
* ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
113
14. General Information
L This product contains NetBSD software and is using it based on the following licence conditions.
/*
* Copyright (c) 1989 The Regents of the University of California.
* All rights reserved.
*
* This code is derived from software contributed to Berkeley by Tom Truscott.
*
* Redistribution and use in source and binary forms, with or without modification, are permitted provided
* that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the
* following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and
* the following disclaimer in the documentation and/or other materials provided with the distribution.
* 3. All advertising materials mentioning features or use of this software must display the following
* acknowledgement:
* This product includes software developed by the University of California, Berkeley and its
* contributors.
* 4. Neither the name of the University nor the names of its contributors may be used to endorse or
* promote products derived from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND ANY
* EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY
* DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
* ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
L This product contains NetBSD software and is using it based on the following licence conditions.
/*
* Copyright (c) 1987, 1993, 1994
* The Regents of the University of California. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without modification, are permitted provided
* that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the
* following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and
* the following disclaimer in the documentation and/or other materials provided with the distribution.
* 3. All advertising materials mentioning features or use of this software must display the following
* acknowledgement:
* This product includes software developed by the University of California, Berkeley and its
* contributors.
* 4. Neither the name of the University nor the names of its contributors may be used to endorse or
* promote products derived from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND ANY
* EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY
* DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
114
14. General Information
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
* ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
L This product contains NetBSD software and is using it based on the following licence conditions.
/** Copyright (c) 1990, 1993
* The Regents of the University of California. All rights reserved.
*
* This code is derived from software contributed to Berkeley by Chris Torek.
*
* Redistribution and use in source and binary forms, with or without modification, are permitted provided
* that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the
* following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and
* the following disclaimer in the documentation and/or other materials provided with the distribution.
* 3. Neither the name of the University nor the names of its contributors may be used to endorse or
* promote products derived from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND ANY
* EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY
* DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
* ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
L This product contains thttpd software that ACMELabs developed and is using it based on the following licence
conditions.
Copyright 1995,1998,1999, 2000 by Jef Poskanzer <jef@acme.com>.
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided
that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the
following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and
the following disclaimer in the documentation and/or other materials provided with the distribution.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
115
14. General Information
L This product contains NetBSD software and is using it based on the following licence conditions.
/** Copyright (c) 1990 The Regents of the University of California.
* All rights reserved.
*
* This code is derived from software contributed to Berkeley by Chris Torek.
*
* Redistribution and use in source and binary forms, with or without modification, are permitted provided
* that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the
* following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and
* the following disclaimer in the documentation and/or other materials provided with the distribution.
* 3. Neither the name of the University nor the names of its contributors may be used to endorse or
* promote products derived from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND ANY
* EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY
* DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
* ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
L This product contains NetBSD software and is using it based on the following licence conditions.
/** Copyright (c) 1990 The Regents of the University of California.
* All rights reserved.
*
* This code is derived from software contributed to Berkeley by Chris Torek.
*
* Redistribution and use in source and binary forms, with or without modification, are permitted provided
* that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the
* following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and
* the following disclaimer in the documentation and/or other materials provided with the distribution.
* 3. Neither the name of the University nor the names of its contributors may be used to endorse or
* promote products derived from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND ANY
* EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY
* DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
* ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
116
14. General Information
L This product contains NetBSD software and is using it based on the following licence conditions.
/*
* Copyright (c) 1989 The Regents of the University of California.
* All rights reserved.
*
* This code is derived from software contributed to Berkeley by Tom Truscott.
*
* Redistribution and use in source and binary forms, with or without modification, are permitted provided
* that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the
* following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and
* the following disclaimer in the documentation and/or other materials provided with the distribution.
* 3. All advertising materials mentioning features or use of this software must display the following
* acknowledgement:
* This product includes software developed by the University of California, Berkeley and its
* contributors.
* 4. Neither the name of the University nor the names of its contributors may be used to endorse or
* promote products derived from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND ANY
* EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY
* DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
* ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
L JPEG
This software is based in part on the work of the Independent JPEG Group.
117
15. Index
15. Index
15.1 Index
#
#100 Quick setup: 57
#101 Date and time: 22
#102 Your logo: 22
#103 Your fax number: 23
#110 Language: 57
#120 Dialing mode: 18
#121 Flash time: 57
#145 LCD display contrast: 57
#155 Change password: 58
#158 Maintenance time: 58
#161 Ringer pattern: 58
#210 FAX ring count: 58
#216 Automatic caller’s list: 58
#226 Time adjustment: 58
#380 Paper size in the standard input tray: 58
#382 Paper size in the optional input tray: 58
#383 Paper type: 59
#401 Confirmation report: 43, 61
#402 Automatic journal report: 43, 61
#403 Power save: 59
#411 Overseas mode: 61
#412 Delayed send: 62
#413 ECM selection: 62
#416 Connecting tone: 62
#418 Maximum fax speed: 62
#430 Distinctive Ring: 55
#431 Fax ring pattern: 55
#432 Auto reduction: 63
#434 Fax activation code: 63
#437 Memory reception alert: 63
#438 Friendly reception: 63
#440 Paper input tray setting for fax: 63
#442 PC fax setting: 64
#443 PC fax reception: 24
#445 Legal-size fax send: 64
#459 Set fax features to default: 64
#460 Paper input tray setting for copy: 65
#461 Default copy resolution: 65
#462 Contrast hold: 65
#463 Default operation mode: 59
#464 Mode timer: 59
#467 Page layout hold: 65
#468 Zoom hold: 65
#469 Collate hold: 65
#470 Duplex hold: 65
#480 Drum cleaning: 104
#482 Toner save: 14, 59
#485 Colour calibration for all colours: 77
#486 Colour calibration for cyan: 77
#487 Colour calibration for magenta: 77
#488 Colour calibration for yellow: 77
#489 Colour calibration for black: 77
#493 Scan mode: 69
#494 Scan parameter hold: 69
#495 Monochrome scan type: 69
#500 DHCP mode: 71
118
#501 IP address: 71
#502 Subnet mask: 71
#503 Default gateway: 71
#504 DNS server #1: 71
#505 DNS server #2: 71
#507 Machine name: 71
#508 MAC address: 71
#532 IP filtering: 72
#533 Auto IP: 72
#534 HTTPD: 72
#535 IPv6 protocol: 72
#565 Paper input tray setting for the scan to e-mail
print feature: 72
#760 Paper input tray in PCL: 66
#762 Number of copies in PCL: 66
#763 Paper size in PCL: 66
#764 Image reduction in PCL: 66
#765 Recording paper direction in PCL: 66
#766 A4 wide printing in PCL: 66
#767 Line per page in PCL: 66
#768 Font source in PCL: 66
#769 Font number in PCL: 67
#770 Font pitch/point in PCL: 67
#771 Symbol set in PCL: 67
#772 Line breaks in PCL: 67
#773 Auto continue mode: 67
#774 Data timeout: 67
#775 Monochrome page detect: 67
#776 Mutual A4/letter print: 68
A Address list: 104
Answering machine: 50
Auto continue mode (Feature #773): 67
Auto IP (Feature #533): 72
Automatic document feeder: 20, 37, 44
Automatic duplex unit (optional): 80
Auto reduction (Feature #432): 63
B Basic features: 57
Broadcast programming list: 104
Broadcast transmission: 46
C Call Display
Calling back: 53
Storing: 54
Caller’s list (Feature #216): 58
Character entry: 75
Cleaning: 101, 102, 103
Collate hold (Feature #469): 65
Colour calibration
Black (Feature #489): 77
Cyan (Feature #486): 77
Magenta (Feature #487): 77
Offset (Feature #485): 77
Yellow (Feature #488): 77
Colour test list: 104
Confirmation report (Feature #401): 43, 61
Connecting tone (Feature #416): 62
Connections: 17
LAN: 17
USB: 25
15. Index
Contrast hold (Feature #462): 65
Copy: 36
Booklet: 41
Collation: 38
Duplex: 41
Easy repeat: 39
N in 1: 40
N in 1 (Separate): 41
Poster: 40
Proof set: 38
Quick ID: 39
Reserve: 41
Zoom: 37
Copy features: 65
D Data timeout (Feature #774): 67
Date and time (Feature #101): 22
Default copy resolution (Feature #461): 65
Default gateway (Feature #503): 71
Default operation mode (Feature #463): 59
Delayed transmission (Feature #412): 62
DHCP mode (Feature #500): 71
Dialing mode (Feature #120): 18
Directory: 44
Display
Contrast (Feature #145): 57
Error messages: 83
Distinctive Ring service (Feature #430): 55
DNS server #1 (Feature #504): 71
DNS server #2 (Feature #505): 71
Document size: 19
Drum cartridge: 10
Drum cleaning (Feature #480): 104
Drum life: 107
Duplex hold (Feature #470): 65
E ECM selection (Feature #413): 62
Envelope: 29
Error messages: 82, 83
Extension telephone: 49
F Fax activation code (Feature #434): 63
Fax features: 61
Fax number (Feature #103): 23
FAX ONLY mode: 48
FAX ring count (Feature #210): 58
Flash time (Feature #121): 57
Friendly reception (Feature #438): 63
FTP server list: 104
H Handset unit (optional): 78
Help: 21
Basic settings: 21
Call Display: 21
Copier: 21
Directory: 21
Fax sending/receiving: 21
Feature list: 21
Reports: 21
HTTPD (Feature #534): 72
I
Input tray (optional): 80
IP address (Feature #501): 71
IP filtering (Feature #532): 72
IPv6 protocol (Feature #535): 72
J
Jams
Document: 100
Recording paper: 95
Journal report (Feature #402): 43, 61
Junk fax prohibitor: 51
L Label: 29
LAN features: 71
Language (Feature #110): 57
Legal-size fax send (Feature #445): 64
Logo (Feature #102): 22
M MAC address (Feature #508): 71
Machine name (Feature #507): 71
Maintenance time (Feature #158): 58
Maximum fax speed (Feature #418): 62
Memory reception alert (Feature #437): 63
Mode timer (Feature #464): 59
Monochrome page detect (Feature #775): 67
Monochrome scan type (Feature #495): 69
Multi-Function Station software
Activating: 26
Installing: 24
Uninstalling: 26
Mutual A4/letter print (Feature #776): 68
N Navigator directory
Sending faxes: 45
Storing: 44
Network features: 73
O OCR software: 33
One-touch dial
Sending faxes: 45
Storing: 44
Optional auto duplex unit: 80
Optional handset unit: 78
Optional input tray: 80
Overseas mode (Feature #411): 61
P Page layout hold (Feature #467): 65
Paper input tray setting
Copy (Feature #460): 65
Fax (Feature #440): 63
PCL (Feature #760): 66
Scan to e-mail print (Feature #565): 72
Paper size
Optional input tray (Feature #382): 58
Standard input tray (Feature #380): 58
Paper type (Feature #383): 59
Password (Feature #155): 58
PC fax reception (Feature #443): 24
PC fax setting (Feature #442): 64
PCL
A4 wide printing (Feature #766): 66
Font number (Feature #769): 67
Font pitch/point (Feature #770): 67
Font source (Feature #768): 66
Image reduction (Feature #764): 66
119
15. Index
Line breaks (Feature #772): 67
Line per page (Feature #767): 66
Number of copies (Feature #762): 66
Paper input tray (Feature #760): 66
Paper size (Feature #763): 66
Recording paper direction (Feature #765): 66
Symbol set (Feature #771): 67
PCL font list: 104
PC print features: 66
Power failure: 93
Power save (Feature #403): 59
Power switch: 18
Print
Duplex: 30
E-mail attachment: 30
Special media: 29
Printer test: 104
Programming: 56
Pull scan: 34
Scan application: 34
Viewer: 34
Push scan: 32
E-mail: 32
E-mail server: 33
File: 32
FTP: 33
OCR: 33
Viewer: 32
Q Quick scan: 44
Quick setup (Feature #100): 57
R Receiving faxes
Automatically: 48
Computer: 52
Manually: 49
Recording paper: 14
Recording paper size: 106
Redialing: 43, 45
Reports
Address: 104
Broadcast programming: 104
Broadcast sending: 47
Call Display: 58, 104
Colour test: 104
Confirmation: 43, 61
FTP server: 104
Journal: 43, 104
PCL font: 104
Power down: 93
Printer test: 104
Setup: 104
Telephone number: 104
Reset fax features (Feature #459): 64
Resolution: 36, 43
Ringer pattern (Feature #161): 58
Ring pattern for Distinctive Ring (Feature #431): 55
S Scan features: 69
Scan mode (Feature #493): 69
Scanner glass: 19, 36, 43
120
Scan parameter hold (Feature #494): 69
Scan to e-mail print: 30
Sending faxes
Broadcast: 47
Computer document: 48
From memory: 44
Manually: 43
Navigator directory: 45
One-touch dial: 45
Set fax default (Feature #459): 64
Setup list: 104
Storing
Broadcast: 46
Navigator directory: 44
One-touch dial: 44
Subnet mask (Feature #502): 71
T Telephone number list: 104
TEL mode: 49
Time adjustment (Feature #226): 58
Toner cartridge: 10
Toner life: 106
Toner save (Feature #482): 14, 59
Transparency: 29
V Volume: 21
W Waste toner cartridge: 9
Waste toner cartridge life: 107
Z Zoom hold (Feature #468): 65
Notes
121
Notes
122
Notes
123
PNQX1474ZA
CM0608CN0 (CD)
Download PDF
Similar pages