User’s Manual of IGT-90x
User’s Manual
IGT-902 / 902T
IGT-902S / 902TS
IGT-905A
10/100/1000Base-T to 1000Base-SX / LX
Industrial Managed Media Converter
-1-
User’s Manual of IGT-90x
Trademarks
Copyright © PLANET Technology Corp. 2010.
Contents subject to which revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and
makes no warranty and representation, either implied or expressed, with respect to the quality, performance,
merchantability, or fitness for a particular purpose.
PLANET has made every effort to ensure that this User's Manual is accurate; PLANET disclaims liability for any
inaccuracies or omissions that may have occurred.
Information in this User's Manual is subject to change without notice and does not represent a commitment on the part of
PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this User's Manual. PLANET
makes no commitment to update or keep current the information in this User's Manual, and reserves the right to make
improvements to this User's Manual and/or to the products described in this User's Manual, at any time without notice.
If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your comments and
suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the Instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at whose own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user
may be required to take adequate measures.
WEEE Warning
To avoid the potential effects on the environment and human health as a result of the presence of
hazardous substances in electrical and electronic equipment, end users of electrical and electronic
equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of
WEEE as unsorted municipal waste and have to collect such WEEE separately.
Revision
PLANET Industrial Managed Gigabit Ethernet Media Converter User's Manual
FOR MODELS: IGT-902 / IGT-902T / IGT-902S / IGT-902TS / IGT-905A
REVISION: 1.1 (APRIL.2010)
Part No.: 2080-AA1130-002
-2-
User’s Manual of IGT-90x
TABLE OF CONTENTS
1. INTRODUCTION .............................................................................................................5
1.1 Package Contents ..................................................................................................................................................... 5
1.2 How to Use This Manual ........................................................................................................................................... 5
1.3 Product Description ................................................................................................................................................... 6
1.4 Applications ............................................................................................................................................................... 6
1.5 Product Features....................................................................................................................................................... 7
1.6 Product Specification................................................................................................................................................. 8
2. HARDWARE INSTALLATION ......................................................................................10
2.1 IGT-90X Front Panel ............................................................................................................................................... 10
2.1.1 LED Indicators .................................................................................................................................................. 11
2.1.2 IGT-90X Rear Panel ......................................................................................................................................... 11
2.1.3 Wiring the Power Inputs.................................................................................................................................... 11
2.1.4 Wiring the Fault Alarm Contact......................................................................................................................... 13
2.2 Mounting Installation ............................................................................................................................................... 13
2.2.1 DIN-Rail Mounting ............................................................................................................................................ 14
2.2.2 Wall Mount Plate Mounting............................................................................................................................... 15
2.2.3 Stand-alone Installation .................................................................................................................................... 16
3. INDUSTRIAL MEDIA CONVERTER MANAGEMENT.................................................19
3.1 Overview ................................................................................................................................................................. 19
3.2 Requirements .......................................................................................................................................................... 19
3.3 Management Methods............................................................................................................................................. 19
3.3.1 Web Management ............................................................................................................................................ 20
3.3.2 Login the Industrial Managed Media Converter................................................................................................ 20
3.3.3 SNMP Management ......................................................................................................................................... 21
3.3.4 PLANET Smart Discovery Utility....................................................................................................................... 21
4. WEB MANAGEMENT ...................................................................................................24
4.1 Main Menu............................................................................................................................................................... 24
4.2 System .................................................................................................................................................................... 25
4.2.1 System Information........................................................................................................................................... 25
4.2.2 IP Configuration ................................................................................................................................................ 26
4.2.3 Password Setting.............................................................................................................................................. 27
4.2.4 Firmware Upgrade ............................................................................................................................................ 28
4.2.5 SNMP Management ......................................................................................................................................... 31
-3-
User’s Manual of IGT-90x
4.2.6 Factory Default ................................................................................................................................................. 33
4.2.7 System Reboot ................................................................................................................................................. 35
4.3 Port Management.................................................................................................................................................... 37
4.3.1 Port Configuration............................................................................................................................................. 37
4.3.2 Port Status ........................................................................................................................................................ 40
4.3.3 Port Statistics.................................................................................................................................................... 40
4.4 Converter Configuration .......................................................................................................................................... 42
4.5 VLAN ....................................................................................................................................................................... 43
4.5.1 VLAN Group ..................................................................................................................................................... 45
4.5.2 VLAN Per Port Setting ...................................................................................................................................... 47
4.5.3 Q-in-Q VLAN Setting ........................................................................................................................................ 48
4.6 Quality of Service .................................................................................................................................................... 49
4.7 OAM Setup.............................................................................................................................................................. 52
4.7.1 Local TS-1000 OAM Setup ............................................................................................................................... 52
4.7.2 Remote TS-1000 OAM Setup ........................................................................................................................... 53
4.7.3 TS-1000 Loop Back Test .................................................................................................................................. 55
4.7.4 802.3ah Setup .................................................................................................................................................. 57
4.7.5 802.3ah Loop Back Test................................................................................................................................... 58
4.8 Security ................................................................................................................................................................... 60
4.9 Logout ..................................................................................................................................................................... 61
5. TROUBLE SHOOTING .................................................................................................62
APPENDIX A NETWORKING CONNECTION..................................................................63
A.1 Device‘s RJ-45 Pin Assignments ............................................................................................................................ 63
A.2 RJ-45 Cable Pin Assignment .................................................................................................................................. 63
A.3 Fiber Optical Cable Connection Parameter ............................................................................................................ 64
-4-
User’s Manual of IGT-90x
1. INTRODUCTION
1.1 Package Contents
Check the contents of your package for following parts:
●
Industrial Managed Gigabit Ethernet Media Converter x1
●
CD-ROM User's Manual x1
●
Quick Installation Guide x1
●
Wall Mount Kit x1
●
Rack Mount Kit x1
If any of these are missing or damaged, please contact your dealer immediately, if possible, retain the carton including the
original packing material, and use them against to repack the product in case there is a need to return it to us for repair.
IGT-905A is with one vacant SFP module slot. The 1000Base-SX / LX SFP module is not bundled
with in the package.
1.2 How to Use This Manual
The Industrial Managed Media Converter User’s Manual is structured as followings:
Section 2, Hardware Installation
It explains the functions of Industrial Managed Media Converter and how to install the Industrial Managed Media
Converter.
Section 3, Industrial Media Converter Management
It contains information about how to manage the Industrial Managed Media Converter.
Section 4, Web Management
It contains information about the Web management function from the Industrial Managed Media Converter.
Section 5, Troubleshooting
It contains troubleshooting guide of Industrial Managed Media Converter.
Appendix A
It contains cable information of Industrial Managed Media Converter.
The term of “Industrial Managed Media Converter” In the following section of this user’s manual means the IGT-90X.
-5-
User’s Manual of IGT-90x
1.3 Product Description
The Industrial Managed Media Converter IGT-90X provide conversion between 10/100/1000Base-T and 1000Base-SX
/LX network. There are SC / LC connectors and single-mode / multi-mode media for your needs. Ethernet signal that
allows two type segments connect easily, efficiently and inexpensively.
The Industrial Managed Media Converter equipped with remote Web / SNMP interface. With its built-in Web-based
management, the Industrial Managed Media Converter offers an easy-to-use, platform-independent management and
configuration facility and can be programmed for advanced management functions. Such as IP address Configuration /
DHCP Client function, password setting / firmware upgrade, system reboot / factory default, port configuration that include
TP / Fiber port speed duplex mode setting, flow control setting and Ingress/Egress bandwidth control setting, converter
configuration that include maximum packet length setting, Broadcast / Multicast / Unicast storm control setting, 16 IEEE
802.1Q VLAN groups support and powerful Q-in-Q VLAN function, Quality of Service (QoS), TS-1000 / IEEE 802.3ah
OAM function and TCP & UDP filter function. It supports standard Simple Network Management Protocol (SNMP) and can
be managed via any standard-based management software as well.
With Gigabit mini GBIC interface, the IGT-905A is with high reliability and flexibility to extend the distance from 220m to
120Km. It depends on the Gigabit mini GBIC modules.
1.4 Applications
Access Control System – Traditional Installation
Industrial area Media Converter for data receive and forwarding
Most of the enterprises performed centralize manage to remote access machine or other network equipment via Internet
network or Fiber optical network. With connection to IGT-90X which cans extensible distance of network, IGT-90X not only
provides higher speed transfer but also could be managed by remote Web interface. The Fiber extend distance can be up
to 10km on IGT-902S/902TS and 120km on IGT-905A or 550m on IGT-902/902T in a local range.
The Gigabit port supporting 9K jumbo packet can handle large amounts of data transmission in a secure topology linking
to a backbone Switch or high-power servers. The Industrial Managed Media Converter with the slim type IP 30 metal
shape is ideal for most Heavy Industrial demanding environments.
-6-
User’s Manual of IGT-90x
1.5 Product Features
¾
Interface
„ 1-Port 10/100/1000Base-T RJ-45 with Auto-negotiation and Auto-MDI/MDI-X function
„ 1 Port 1000Base-SX SC interface, provide long distance up to 220/550m on IGT-902/902T
„ 1 Port 1000Base-LX SC interface, provides long distance for 10km on IGT-902S/902TS
„ 1 Mini-GBIC slot, port provides multi choice of SFP modules on IGT-905A
¾
Industrial Conformance
„ 12 to 48V DC, redundant power with polarity reverse protect function
„ -10 to 60 Degree C operation temperature for IGT-902 / 902S
„ -30 to 75 Degree C operation temperature for IGT-902T / 902TS / 905A
„ IP-30 metal case
„ Relay alarm for port breakdown
„ Supports 6KVDC Ethernet ESD protection
„ Free fall, Shock and Vibration Stability
„ DIN-Rail and Wall-mountable hardware design
¾
Layer 2 Features
„ Store-and-Forward mechanism
„ Prevents packet loss with back pressure (Half-Duplex) and IEEE 802.3x PAUSE frame flow control
(Full-Duplex)
„ Maximum frame size to 9216 Bytes
„ Loop detection / Broadcast / Multicast / Unicast storm control
„ Supports VLANs
• IEEE 802.1Q Tagged based VLAN
• Up to 16 VLANs groups, out of 4K VLAN IDs
-7-
User’s Manual of IGT-90x
• Management VLAN
¾
Quality of Service
„ Ingress/Egress Bandwidth control on TP / Fiber port
„ 4 priority queues, strict priority and Weighted Round Robin (WRR)
„ Traffic classification by:
• IEEE 802.1p Class of Service
• IP DSCP priority
• IP Address priority
¾
Management
„ Built-in IP-based Web interface for remote management
„ SNMP v1 / v2c and 4 RMON groups
„ Event trap and SNMP trap support
„ Manual IP address setting / DHCP client for IP address assignment
„ TS-1000 OAM / IEEE 802.3ah OAM / Loop Back Test
„ 16 TCP / UDP Filter groups
„ Password setting, IP setting and devices description setting through Planet Smart discovery utility
„ Firmware upgrade via remote Web interface
„ Reset Button at the front panel for the factory default reset
1.6 Product Specification
Product
IGT-902
IGT-902T
IGT-902S
IGT-902TS
IGT-905A
Hardware Specification
Copper Interface
1 x 10/100/1000Base-T RJ-45 Auto-MDI/MDI-X ports
Optic Interface
SC
Optical Mode
Optic Wavelength
SFP
Vary on
Multi-mode
Single mode
850nm
1310nm
-*
module
Launch
MAX.
-4 dBm
-3 dm
-*
Power(dBm)
Min.
-9.5 dBm
-9.5dBm
-*
-13.5 dBm
-14.4 dBm
-*
-18 dBm
-20 dBm
-*
Receive Sensitivity
Maximum Input power
10/20Mbps for Half / Full-Duplex
Twisted-pair
Speed
100/200Mbps for Half / Full-Duplex
2000Mbps for Full-Duplex
Fiber-optic
2000Mbps for Full-Duplex
10Base-T: 2-pair UTP Cat. 3,4,5, up to 100 m
Twisted-pair
100Base-TX: 2-pair UTP Cat. 5, up to 100 m
1000Base-T: 4-pair STP Cat 5,6 up to 100m
Cable
Fiber-optic
Cable
LED indicator
y 50/125μm or 62.5/125μm multi-mode fiber cable, up to 220/550m.
y 9/125μm single-mode cable, provides long distance for
10/15/20/30/40/50/60/70/120km (very on fiber transceiver or SFP module)
Power: P1, P2, Fault
TP: LNK/ACT, 1000
Fiber: LNK/ACT
-8-
User’s Manual of IGT-90x
Power Input
Power Consumption
Operating Temperature
Operating Humidity
Storage Temperature
12 to 48V DC
Redundant power with polarity reverse protection function
7.7 Watts/ 26 BTU (maximum)
-10~60
-30~75
-10~60
-30~75
-30~75
Degree C
Degree C
Degree C
Degree C
Degree C
5~90% non-condensing
-20~85
-40~85
-20~85
-40~85
-40~85
Degree C
Degree C
Degree C
Degree C
Degree C
Storage Humidity
5~90% non-condensing
Dimension (W x D x H)
13.5 x 8.5 x 3.2 mm
Weight
423g
Installation
DIN rail kit and wall mount ear
Management and Layer 2 Features
Management Interface
WEB / SNMP v1, v2c
Port disable/enable
Port Configuration
Auto-negotiation 10/100/1000Mbps Full and Half duplex mode selection.
Flow Control disable / enable. Bandwidth control on each port.
VLAN
IEEE 802.1q Tagged Based VLAN , 4K VLAN ID, up to 16 VLAN groups
Q-in-Q VLAN
Traffic classification based on :
QoS
• 802.1p priority
• IP DSCP field in IP Packet
• IP Address
Ingress / Egress bandwidth control
Bandwidth Control
• Rate range: 512kbps to 500Mbps
Storm control
• Broadcast / Multicast / Unknown Unicast packet
Standard Conformance
Emissions
FCC Class A, CE Class A
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3z Gigabit SX/LX
Standard
IEEE 802.3ab Gigabit 1000T
IEEE 802.3x Flow Control and Back pressure
IEEE 802.1p Class of service
IEEE 802.1Q VLAN Tagging
IEEE 802.3ah OAM
IEC60068-2-32 (Free fall)
Stability
IEC60068-2-27 (Shock)
IEC60068-2-6 (Vibration)
* =Depend on the various SFP modules
-9-
User’s Manual of IGT-90x
2. HARDWARE INSTALLATION
This product provides three different running speeds – 10Mbps, 100Mbps and 1000Mbps in the same Industrial Managed
Media Converter and automatically distinguishes the speed of incoming connection.
This section describes the functionalities of IGT-90X’s components and guides how to install it on the DIN Rail Basic
knowledge of networking is assumed. Please read this chapter completely before continuing.
2.1 IGT-90X Front Panel
The Front Panel of the Industrial Managed Media Converter consists of one 1000Base-SX / 1000Base-LX / mini-GBIC
SFP ports and one Auto-Sensing 10/100/1000Mbps Ethernet RJ-45 Port. Figure 2-1, 2-2 & 2-3 shows a front panel of
Industrial Managed Media Converter.
Figure 2-1 PLANET
Figure 2-2 PLANET
Figure 2-3 PLANET
IGT-902 / IGT-902S Front Panel
IGT-902T / IGT-902TS Front Panel
IGT-905A Front Panel
-10-
User’s Manual of IGT-90x
2.1.1 LED Indicators
LED
Color
P1
P2
FAULT
Green
Green
Green
Fiber
LNK /ACT
Green
Function
Lit
Lit
Lit
Lights
TP 1000
Blinks
To indicate the Fiber Optical Port is receiving or sending data.
Lights
To indicate that the Gigabit Ethernet Port is successfully connecting to the
network at 1000Mbps. OFF indicate the Gigabit Ethernet Port is
successfully connecting to the network at 10/100Mbps.
Lights
To indicate that the Gigabit Ethernet Port is successfully connecting to the
network at 10/100/1000Mbps.
Blinks
To indicate the Gigabit Ethernet Port is receiving or sending data.
Green
TP
LNK /ACT
Indicate the power 1 has power.
Indicate the power 2 has power.
Indicate the either power 1 or power 2 has no power.
To indicate that the Fiber Optical Port is successfully connecting to the
network at 1000Mbps.
To press and release the RESET button. The IGT-90X will back to the factory default mode. Be sure that you
backup the current configuration of IGT-90X; else the entire configuration will be erased when pressing the
“RESET” button.
• Press and release the RESET button shortly, the device will be rebooted.
• Press the RESET button about 10 seconds and release, the device will back to the factory default
mode; the entire configuration will be erased to default setting.
2.1.2 IGT-90X Rear Panel
The upper panel of the Industrial Managed Media Converter consist one terminal block connector within two DC power
inputs. Figure 2-4 shows the upper panel of the Industrial Managed Media Converter.
■
IGT-90X series Upper Panel
Figure 2-4 Upper Panel of IGT-90X
2.1.3 Wiring the Power Inputs
The 6-contact terminal block connector on the top panel of Industrial Media Converter is used for two DC redundant
powers input. Please follow the steps below to insert the power wire.
1. Insert positive / negative DC power wires into the contacts 1 and 2 for POWER 1, or 5 and 6 for POWER 2.
-11-
User’s Manual of IGT-90x
2. Tighten the wire-clamp screws for preventing the wires from loosing.
1
2
Power 1
-
3
4
5
Fault
+
6
Power 2
-
+
The wire gauge for the terminal block should be in the range between 12 ~ 24 AWG.
-12-
User’s Manual of IGT-90x
2.1.4 Wiring the Fault Alarm Contact
The fault alarm contacts are in the middle of the terminal block connector as the picture shows below. Inserting the wires,
the Industrial Management Media Converter will detect the fault status of the power failure, or port link failure (available for
managed model) and then forms an open circuit. The following illustration shows an application example for wiring the
fault alarm contacts.
1
2
3
4
5
6
Insert the wires into the fault alarm contacts
1.
The wire gauge for the terminal block should be in the range between 12 ~ 24 AWG.
2.
Alarm relay circuit accepts up to 30V, max. 3A currents.
2.2 Mounting Installation
This section describes how to install the Industrial Managed Media Converter and make connections to it. Please read the
following topics and perform the procedures in the order being presented.
In the installation steps below, this Manual use IGS-801(PLANET 8 Port Industrial Gigabit Switch) as the
example. However, the steps for PLANET Industrial Switch & Industrial Media / Serial Converter are
similar. Terms of “Industrial Equipment” in following section means the PLANET Industrial devices that
mentioned above.
-13-
User’s Manual of IGT-90x
2.2.1 DIN-Rail Mounting
The DIN-Rail is screwed on the Industrial Equipment when out of factory. When need to replace the wall mount application
with DIN-Rail application on Industrial Equipment, please refer to following figures to screw the DIN-Rail on the Industrial
Equipment. To hang the Industrial Equipment, follow the below steps:
Step 1: screw the DIN-Rail on the Industrial Managed Media Converter.
Step 2: Lightly press the button of DIN-Rail into the track.
-14-
User’s Manual of IGT-90x
Step 3: Check the DIN-Rail is tightly on the track.
Step 4: Please refer to following procedures to remove the Industrial Gigabit Ethernet Switch from the track.
Step 5: Lightly press the button of DIN-Rail for remove it from the track.
2.2.2 Wall Mount Plate Mounting
To install the Industrial Equipment on the wall, please follows the instructions described below.
Step 1: Remove the DIN-Rail from the Industrial Equipment; loose the screws to remove the DIN-Rail.
Step 2: Place the wall mount plate on the rear panel of the Industrial Equipment.
-15-
User’s Manual of IGT-90x
Step 3: Use the screws to screw the wall mount plate on the Industrial Equipment.
Step 4: Use the hook holes at the corners of the wall mount plate to hang the Industrial Equipment on the wall.
Step 5: To remove the wall mount plate, reverse steps above.
2.2.3 Stand-alone Installation
IGT-902 / IGT-902T/ IGT-902S/ IGT-902TS Installation:
To install an Industrial Managed Media Converter stand-alone, on a Track or wall mount, simply complete the following
steps:
Step 1: Turn off the DC power of the device/station in a network to which IGT-90X will be attached.
Step 2: Ensure that there is no activity in the network.
Step 3: Attach fiber cable from the Industrial Managed Media Converter to the fiber network. TX, RX must be paired at
both ends.
Step 4: Connect the DC power to the IGT-90X and verify that the Power LED lights up.
Step 5: Turn on the power of the device/station; the PWR LED (Green) should light when all cables are attached.
Figure 2-5 IGT- 902 / IGT-902T / IGT-902S / IGT-902TS stand-alone installation
-16-
User’s Manual of IGT-90x
Please refers to APPENDIX-A for detailed wiring information of the Industrial Managed Media
Converter. To prevent from optic acceptor malfunction, check the both wires / transmitter before
power on the Industrial Managed Media Converter.
IGT-905A Installation:
IGT-905A is with high reliability and flexibility to extend the distance from 220m to 120Km. It depends on the Gigabit mini
GBIC modules. The SFP transceivers are hot-plug and hot-swappable. You can plug-in and out the transceiver to/from
any SFP port without having to power down the Industrial Managed Media Converter.
To install IGT-905A with 1000Base-SX / LX SFP, simply complete the following steps:
Step 1: Precede with the steps 4 and steps 5 of session 2.2.3 Stand-alone Installation to connect the network cabling
and supply power to your Industrial Managed Media Converter.
Step 2: Slot in the 1000Base-SX / LX SFP. Make sure both side of the SFP transceiver are with the same media type, for
example: 1000Base-SX / 220m & 550m to 1000Base-SX / 220m & 550m, 1000Base-LX / 10km to 1000Base-LX /
10km
Step 3: Connect the fiber cable. Attach the duplex LC connector on the network cable into the SFP transceiver.
Figure 2-6 IGT- 905A stand alone installation
It recommends using PLANET MGB series 1000Base-SX / LX / LX WDM SFP on the IGT-905A. If
you insert a SFP transceiver that is not supported, the IGT-905A will not recognize it.
The following list the available Modules for IGT-905A
MGB-GT
SFP-Port 1000Base-T mini-GBIC module
MGB-SX
SFP-Port 1000Base-SX mini-GBIC module
MGB-LX
SFP-Port 1000Base-LX mini-GBIC module
MGB-L30
SFP-Port 1000Base-LX mini-GBIC module -30KM
MGB-L50
SFP-Port 1000Base-LX mini-GBIC module -50KM
MGB-L70
SFP-Port 1000Base-LX mini-GBIC module -70KM
MGB-L120
SFP-Port 1000Base-LX mini-GBIC module -120KM
-17-
User’s Manual of IGT-90x
MGB-LA10
SFP-Port 1000Base-LX mini-GBIC module- LC WDM(TX:1310nm), SM,10km
MGB-LB10
SFP-Port 1000Base-LX mini-GBIC module- LC WDM(TX:1550nm), SM,10km
MGB-LA20
SFP-Port 1000Base-LX mini-GBIC module- LC WDM(TX:1310nm), SM,20km
MGB-LB20
SFP-Port 1000Base-LX mini-GBIC module- LC WDM(TX:1550nm), SM,20km
MGB-LA40
SFP-Port 1000Base-LX mini-GBIC module- LC WDM(TX:1310nm), SM,40km
MGB-LB40
SFP-Port 1000Base-LX mini-GBIC module- LC WDM(TX:1550nm), SM,40km
-18-
User’s Manual of IGT-90x
3. INDUSTRIAL MEDIA CONVERTER MANAGEMENT
This chapter describes how to manage the Industrial Managed Media Converter. Topics include:
- Overview
- Management methods
- Assigning an IP address to the Industrial Managed Media Converter
- Logging on to the Industrial Managed Media Converter
3.1 Overview
This chapter gives an overview of Industrial Managed Media Converter management. The IGT-90X provides a simply
WEB browser interface. Using this interface, you can perform various Industrial Managed Media Converter configuration
and management activities, including:
„
System
„
Port Management
„
Converter Configuration
„
VLAN
„
Quality of Service
„
OAM Setup
„
Security
„
Logout
Please refer to the following Chapter 4 for more details.
3.2 Requirements
■ Network cables.
For IGT-90x copper interface: Use standard network (UTP) cables with RJ-45 connectors.
For IGT-90x Fiber interface: Use Multi-mode or Single-mode fiber patch cord with SC connectors.
■ Subscriber PC installed with Ethernet NIC (Network Card)
■ Workstations of subscribers running Windows 98/ME, NT4.0, 2000/2003/XP, MAC OS X or later, Linux, UNIX or
other platform compatible with TCP/IP protocols.
■ Above PC installed with WEB Browser, such as Microsoft Internet Explore or Mozilla Firefox
It is recommended to use Internet Explore 7.0 or above to access Industrial Media
Converter.
3.3 Management Methods
The way to manage the IGT-90X:
-Web Management via a network or dial-up connection.
-19-
User’s Manual of IGT-90x
-Using SNMP Network Management Station.
3.3.1 Web Management
The PLANET Industrial Managed Media Converter provides a built-in browser interface. You can manage the Industrial
Managed Media Converter remotely by having a remote host with Web browser, such as Microsoft Internet Explorer,
Netscape Navigator or Mozilla Firefox.
Figure 3-1 Web Management over Ethernet
3.3.2 Login the Industrial Managed Media Converter
The following shows how to startup the Web Management of the Industrial Managed Media Converter, please note the
device is configured through an Ethernet connection, make sure the manager PC must be set on the same IP subnet
address.
For example, the default IP address of the Industrial Managed Media Converter is 192.168.0.100 (the factory-default IP
address), then the manager PC should be set at 192.168.0.x (where x is a number between 1 and 254, except 100), and
the default subnet mask is 255.255.255.0.
Use Internet Explorer 7.0 or above Web browser, enter default IP address http://192.168.0.100
After entering the username and password (default user name and password is “admin”) in login screen then the Web
main screen appears.
Default IP Address: 192.168.0.100
Default Account: admin
Default Password: admin
-20-
User’s Manual of IGT-90x
Figure 3-2 Login Web Page screen
1.
For security reason, please change and memorize the new password after this first setup.
2.
Only accept command in lowercase letter under web interface.
3.3.3 SNMP Management
You can manage the Industrial Managed Media Converter across a LAN using an SNMP Network Management Station
with a graphical user interface.
This management method lets you monitor statistical counters and set Industrial Managed Media Converter parameters
from the remote Network Management Station.
Using this management method:
- The network must run the IP protocol.
- The Managed Media Converter must have an IP address.
3.3.4 PLANET Smart Discovery Utility
For easily list the Industrial Managed Media Converter in your Ethernet environment, the Planet Smart Discovery Utility
from user’s manual CD-ROM is an ideal solution.
The following install instructions guiding you for run the Planet Smart Discovery Utility.
1. Deposit the Planet Smart Discovery Utility in administrator PC.
2. Run this utility and the following screen appears.
-21-
User’s Manual of IGT-90x
Figure 3-3 Planet Smart Discovery Utility Screen
If there are two LAN cards or above in the same administrator PC, choose different LAN card by
use the “Select Adapter” tool.
3. Press “Refresh” button for list current connected devices in the discovery list, the screen is shown as follow.
Figure 3-4 Planet Smart Discovery Utility Screen
1. This utility show all necessary information from the devices, such as MAC Address, Device Name, firmware version,
Device IP Subnet address, also can assign new password, IP Subnet address and description for the devices.
2. After setup completed, press “Update Device”, “Update Multi” or “Update All” button to take affect. The meaning of
the 3 buttons above are shown as below:
• Update Device: use current setting on one single device.
• Update Multi: use current setting on choose multi-devices.
• Update All: use current setting on whole devices in the list.
The same functions mentioned above also can be finding in “Option” tools bar.
-22-
User’s Manual of IGT-90x
3. To click the “Control Packet Force Broadcast” function, it can allow assign new setting value to the Managed Media
Converter under different IP subnet address.
4. Press “Connect to Device” button then the Web login screen appears in Figure 3-2.
5. Press “Exit” button to shutdown the planet Smart Discovery Utility.
-23-
User’s Manual of IGT-90x
4. WEB MANAGEMENT
The IGT-90X Industrial Managed Media Converter provide remote Web interface for management function configuration
and make the Industrial Managed Media Converter operate more effectively - They can be configured through the Web
Browser. A network administrator can manage and monitor the Industrial Managed Media Converter from the local LAN.
This section indicates how to configure the Industrial Managed Media Converter to enable its management function.
4.1 Main Menu
After a successful login, the main screen appears, the main screen displays the Industrial Managed Media Converter
Welcome page. The screen in Figure 4-1 appears.
Figure 4-1 Web Main screen
As listed at the left of the main screen, the configurable management functions are shown as below:
◆
System – Provide System configuration of Industrial Managed Media Converter. Explained in section 4.2.
◆
Port Management – Provide Port Management configuration of Industrial Managed Media Converter.
Explained in section 4.3.
◆
Converter Configuration – Provide Converter configuration of Industrial Managed Media Converter. Explained
in section 4.4.
◆
VLAN – Provide VLAN configuration of Industrial Managed Media Converter. Explained in section 4.5.
◆
Quality of Service – Provide Quality of Service (QoS) function of the Industrial Managed Media Converter.
Explained in section 4.6.
◆
OAM Setup – Provide OAM Setup function of the Industrial Managed Media Converter. Explained in section
4.7.
◆
Security – Provide Security function of the Industrial Managed Media Converter. Explained in section 4.8.
◆
Logout– Provide Logout function of the Industrial Managed Media Converter. Explained in section 4.9.
-24-
User’s Manual of IGT-90x
4.2 System
4.2.1 System Information
The System Information Web page provides information for the current device. System Information Web page helps
network administrator to identify the firmware versions, IP Subnet Address and etc. The screen in Figure 4-2 appears and
Table 4-1 describes the System Information object of Industrial Managed Media Converter.
Figure 4-2 System Information Web page screen
The System Information Web page screen includes the following fields:
MAC Address
Specifies the MAC address of IGT-90X.
Software Version
The current software version running on the IGT-90X.
IP Address
The current IP Address of IGT-90X, the default IP Address is 192.168.0.100.
Subnet Mask
The current Subnet Mask of IGT-90X, the default Subnet Mask is 255.255.255.0.
Gateway
The current gateway of IGT-90X, the factory default gateway is 192.168.0.254.
Description
The current description of IGT-90X, the factory default description is IGT-90X.
Temperature
Display current temperature of IGT-90X in Celsius and Fahrenheit.
Power Status
Display current power supply status of IGT-90X.
Refresh
Refresh current Web page screen of IGT-90X.
Table 4-1 Descriptions of the System Information Web Page Screen Objects
-25-
User’s Manual of IGT-90x
4.2.2 IP Configuration
The IP Configuration includes the DHCP Client, IP Address, Subnet Mask, Gateway and Description. The screen in Figure
4-3 appears and Table 4-2 describes the IP Configuration object of Industrial Managed Media Converter.
Figure 4-3 IP Configuration Web page screen
The IP Configuration Web page screen includes the following configurable data:
DHCP Client
Allow disable or enable the DHCP Client function of the Industrial Managed Media Converter, the
factory default mode is Disable.
IP Address
Allow assigning a new IP address for the Industrial Managed Media Converter, the factory default IP
address is 192.168.0.100.
Subnet Mask
Allow assigning a new subnet mask for the Industrial Managed Media Converter, the factory default
subnet mask is 255.255.255.0.
Gateway
Allow assigning a new gateway for the Industrial Managed Media Converter, the factory default
gateway is 192.168.0.254.
Description
Allow to input a new description for the Industrial Managed Media Converter, up to maximum 32
characters allow.
Apply Button
Press “Apply” button for save current configuration of Industrial Managed Media Converter.
Table 4-2 Descriptions of the IP Configuration Web Page Screen Objects
After change the default IP subnet address, if you forget the IP subnet address. Please press the “Reset”
button in the front panel of Managed Media Converter for 10 seconds, the current setting will be lost and
the Industrial Managed Media Converter will restore to factory default mode.
-26-
User’s Manual of IGT-90x
4.2.3 Password Setting
This function provides administrator to secure Web login. The screen in Figure 4-4 & 4-5 appears and Table 4-3 describes
the Password Setting object of Industrial Managed Media Converter.
Figure 4-4 Password Setting Web page screen
Figure 4-5 Password Setting Successful Web page screen
-27-
User’s Manual of IGT-90x
The Password Setting Web page includes the following configurable data:
Login Name
Displays the user name (admin).
Old Password
Enter the old password is required before entering the new password.
New Password
Specifies the new password. The password is not displayed. As it entered an “y” corresponding to
each character is displayed in the field.
(The maximum length is 16 characters)
Confirm
This confirms the new password. The password entered into this field must be exactly the same
as the password entered in the Password field.
Apply Button
Press “Apply” button for save current configuration of Industrial Managed Media Converter.
Table 4-3 Descriptions of the Password Setting Web Page Screen Objects
4.2.4 Firmware Upgrade
This function provides Firmware Upgrade of the Industrial Managed Media Converter and the screen in Figure 4-6
appears.
Figure 4-6 Firmware Upgrade Web page screen
Press “Browse” button to find the firmware location administrator PC, The screen in Figure 4-7 appears
-28-
User’s Manual of IGT-90x
Figure 4-7 Firmware Upgrade Web page screen
After find the firmware location from administrator PC, press “Upgrade” button to start the firmware upgrade process.
The screen in Figure 4-8 & 4-9 appears.
Figure 4-8 Firmware Upgrade Web page screen
Do not power off the converter until the update progress is complete.
Do not quit the Firmware Upgrade page without press the “Upgrade” button - after the image is
loaded. Or the system won’t apply the new firmware. Users have to repeat the firmware
upgrade processes again.
-29-
User’s Manual of IGT-90x
Figure 4-9 Firmware Upgrade Web page screen
When firmware upgrade process is completed then the following screen appears, please click “here” to re-login the
IGT-90X with latest firmware and the screen in Figure 4-10 & 4-11 appears.
Figure 4-10 Firmware Upgrade Web page screen
-30-
User’s Manual of IGT-90x
Figure 4-11 Login Web page screen
4.2.5 SNMP Management
This function provides SNMP Management and SNMP Trap Receiver Configuration function of the Industrial Managed
Media Converter and the screen in Figure 4-12 & 4-13 appears and Table 4-4 & 4-5 describes the SNMP Management
and SNMP Trap Receiver object of Industrial Managed Media Converter.
Figure 4-12 SNMP Management Web page screen
-31-
User’s Manual of IGT-90x
The SNMP Management Web page includes the following configurable data:
SNMP Agent
Allow disable or enable the SNMP Agent function, the default mode is “Disable”.
SNMP Read Community
Allow input the characters for SNMP Read Community, up to maximum 16 characters
allow.
SNMP Write Community
Allow input the characters for SNMP Write Community, up to maximum 16 characters
allow.
System Name
Allow input the characters for System Name, up to maximum 16 characters allow.
System Location
Allow input the characters for System Location, up to maximum 16 characters allow.
Contact
Allow input the characters for Contact person, up to maximum 16 characters allow.
Apply Button
Press “Apply” button for save current configuration of IGT-90X.
Table 4-4 Descriptions of the SNMP Management Web Page Screen Objects
The IGT-90X supports SNMP v1 / v2c protocol.
Figure 4-13 SNMP Trap Receiver Configuration Web page screen
The SNMP Trap Receiver Configuration Web page includes the following configurable data:
SNMP Trap
Allow disable or enable the SNMP Trap function, the default mode is “Disable”.
SNMP Trap Destination
Allow input the IP address of SNMP Trap Destination.
Trap Event
Cold Start
When IGT-90X executes Cold Start operation, the administrator PC (SNMP Trap
Destination) will receive a Cold Start Trap.
Warm Start
When IGT-90X executes Warm Start operation, the administrator PC (SNMP
Trap Destination) will receive a Warm Start Trap.
Login Fail
When Web login fail situation appears on IGT-90X, the administrator PC (SNMP
Trap Destination) will receive a Login Fail Trap.
-32-
User’s Manual of IGT-90x
Link Up
When TP or Fiber port connection is build up, the administrator PC (SNMP Trap
Destination) will receive a Link Up Trap.
Link Down
When TP or Fiber port connection is Disconnect, the administrator PC (SNMP
Trap Destination) will receive a Link Down Trap.
Apply Button
Press “Apply” button for save current configuration of IGT-90X
Table 4-5 Descriptions of the SNMP Trap Receiver Configuration Web Page Screen Objects
4.2.6 Factory Default
This function provides Factory Default function of the Industrial Managed Media Converter and the screen in Figure 4-14
& 4-15 & 4-16 appears.
Figure 4-14 Factory Default Web page screen
-33-
User’s Manual of IGT-90x
Figure 4-15 Factory Default Web page screen
Figure 4-16 Login Web page screen
-34-
User’s Manual of IGT-90x
4.2.7 System Reboot
This function provides System Reboot function of the Industrial Managed Media Converter and the screen in Figure 4-17
& 4-18 & 4-19 appears.
Figure 4-17 System Reboot Web page screen
Figure 4-18 System Reboot Web page screen
-35-
User’s Manual of IGT-90x
Figure 4-19 Login Web page screen
-36-
User’s Manual of IGT-90x
4.3 Port Management
4.3.1 Port Configuration
This function allows displaying TP / Fiber port status. The Link Status in the screen displays the current connection speed
and duplex mode; else this function will show red “Down” when the TP / Fiber port is disconnected. Press the “Refresh”
button to renew the screen. The screen in Figure 4-20 appears and Table 4-6 describes the Port Configuration object of
IGT-90X.
Figure 4-20 Port Configuration Web Page screen
The Port Configuration Web page includes the following configurable data:
Port
Indicate the TP port and Fiber port.
Link
Displays the current connection speed and duplex mode of TP or Fiber port.
Mode
Allow configuring the TP or Fiber port speed and operation mode. Draw the menu
bar to select the mode.
TP Port:
y
y
y
y
y
y
Auto Speed
1000 Full
100 Full
100 Half
10 Full
10 Half
Setup Auto negotiation
Force sets 1000Mbps Full-Duplex mode
Force sets 100Mbps Full-Duplex mode
Force sets 100Mbps Half-Duplex mode
Force sets 10Mbps Full-Duplex mode
Force sets 10Mbps Half-Duplex mode
Default mode: Auto Speed.
Fiber Port:
y Auto Speed Setup Auto negotiation
y 1000 Full
Force sets 1000Mbps Full-Duplex mode
Default mode: Auto Speed.
Flow Control
Allow Disable or Enable Flow Control of TP or Fiber port.
Enable: IEEE 802.3x Flow Control is enabled on Full-Duplex mode or
Backpressure is enabled on Half-Duplex mode
-37-
User’s Manual of IGT-90x
Disable: No Flow Control or backpressure function on no matter Full-Duplex
or Half-Duplex mode
Default mode: Disable
Ingress Rate Limit
The value of inbound traffic limitation in kilobit-per-second (kbps). The available
options are :
• No Limit
• 512K
• 1M
• 2M
• 4M
• 8M
• 10M
• 50M
• 100M
• 500M
Default mode: No Limit
The Ingress Rate Limit configuration field as show in Figure 4-21.
Egress Shaping
The value of outbound traffic limitation in kilobit-per-second (kbps). The available
options are :
• No Limit
• 512K
• 1M
• 2M
• 4M
• 8M
• 10M
• 50M
• 100M
• 500M
Default mode: No Limit
The Egress Shaping configuration field as show in Figure 4-22.
Apply Button
Press this button for save current configuration of Industrial Managed Media
Converter.
Refresh Button
Press “Refresh” button to refresh current status.
Table 4-6 Descriptions of the Port Configuration Web Page Screen Objects
-38-
User’s Manual of IGT-90x
Figure 4-21 Port Configuration-Ingress Rate Limit Web Page screen
Figure 4-22 Port Configuration-Egress Shaping Web Page screen
-39-
User’s Manual of IGT-90x
4.3.2 Port Status
This function allows displaying TP / Fiber port detail status, such as Link Status, Duplex Mode, Flow control, Speed and
Auto negotiation. Press the “Refresh” button to renew the screen, the screen in Figure 4-23 appears and Table 4-7
describes the Port Status object of Industrial Managed Media Converter.
Figure 4-23 Port Status Web Page screen
The Port Status Web page includes the following configurable data:
Port
Indicate the TP port and Fiber port.
Link Status
Displays the current link status of TP and Fiber port.
Duplex Mode
Displays the current duplex mode of TP and Fiber port.
Flow Control
Displays the current Flow Control status of TP and Fiber port.
Speed
Displays the current speed mode of TP and Fiber port.
Auto Negotiation
Displays the current Auto negotiation status of TP and Fiber port.
Refresh Button
Press “Refresh” button to refresh current status.
Table 4-7 Descriptions of the Port Status Web Page Screen Objects
4.3.3 Port Statistics
This function allows displaying TP / Fiber port detail statistics, press the “Clear” button to clear current counter
information. Press the “Refresh” button to renew the screen, the screen in Figure 4-24 appears.
-40-
User’s Manual of IGT-90x
Figure 4-24 Port Statistics Web Page screen
-41-
User’s Manual of IGT-90x
4.4 Converter Configuration
This function provides useful setting for the IGT-90X as Maximum Packet length, Loop detection, storm control and etc.
The screen in Figure 4-25 appears and Table 4-8 describes the Converter Configuration object of Industrial Managed
Media Converter.
Figure 4-25 Converter Configuration Web Page screen
The Converter Configuration Web page includes the following configurable data:
Maximum Packet Length
Provide maximum packet lengths setting for the IGT-90X, the available options
are 1518 bytes, 2048 bytes and 16K bytes. Default mode is 16K bytes.
Loop Detection
Provide Disable or enable the Loop detection function. Default mode is Disable.
Loop Status
Displays the Loop Detection status.
Broadcast Storm Control
Provide Disable or enable the Broadcast Storm Control function. Default mode is
Disable.
Multicast Storm Control
Provide Disable or enable the Multicast Storm Control function. Default mode is
Disable.
Unicast Storm Control
Provide Disable or enable the Unicast Storm Control function. Default mode is
Disable.
Storm Trigger Counter
Provide storm Trigger Counter setting and the available options are:
64 broadcast
32 broadcast
16 broadcast
8 broadcast
Default mode is 64 broadcast.
Storm Filter Timer
Provide storm Filter Timer setting and the available options are:
800ms
400ms
-42-
User’s Manual of IGT-90x
200ms
100ms
Default mode is 800ms.
Apply Button
Press this button for save current configuration of Managed Media Converter.
Table 4-8 Descriptions of the Converter Configuration Web Page Screen Objects
4.5 VLAN
A Virtual LAN (VLAN) is a logical network grouping that limits the broadcast domain. It allows you to isolate network traffic
so only members of the VLAN receive traffic from the same VLAN members. Basically, creating a VLAN from a converter
is logically equivalent of reconnecting a group of network devices to another Layer 2 switch. However, all the network
devices are still plug into the same switch physically.
The Industrial Managed Media Converter supports IEEE 802.1Q (tagged-based) VLAN setting in web management page.
In the default configuration, VLAN support is “No VLAN”.
IEEE 802.1Q VLANs
IEEE 802.1Q (tagged) VLAN are implemented on the Industrial Managed Media Converter. 802.1Q VLAN require tagging,
which enables them to span the entire network (assuming all devices on the network are IEEE 802.1Q-compliant).
VLAN allow a network to be segmented in order to reduce the size of broadcast domains. All packets entering a VLAN will
only be forwarded to the stations (over IEEE 802.1Q enabled switches) that are members of that VLAN, and this includes
broadcast, multicast and unicast packets from unknown sources.
VLAN can also provide a level of security to your network. IEEE 802.1Q VLAN will only deliver packets between stations
that are members of the VLAN. Any port can be configured as either tagging or untagging. The untagging feature of IEEE
802.1Q VLAN allows VLAN to work with legacy switches that don't recognize VLAN tags in packet headers. The tagging
feature allows VLAN to span multiple 802.1Q-compliant switches through a single physical connection and allows
Spanning Tree to be enabled on all ports and work normally.
Any port can be configured as either tagging or untagging. The untagging feature of IEEE 802.1Q VLAN allows VLAN to
work with legacy switches that don’t recognize VLAN tags in packet headers. The tagging feature allows VLAN to span
multiple 802.1Q-compliant switches through a single physical connection and allows Spanning Tree to be enabled on all
ports and work normally.
Some relevant terms:
Tag - The act of putting 802.1Q VLAN information into the header of a packet.
Untag - The act of stripping 802.1Q VLAN information out of the packet header.
802.1Q VLAN Tags
The figure below shows the 802.1Q VLAN tag. There are four additional octets inserted after the source MAC address.
Their presence is indicated by a value of 0x8100 in the Ether Type field. When a packet's Ether Type field is equal to
0x8100, the packet carries the IEEE 802.1Q/802.1p tag. The tag is contained in the following two octets and consists of 3
bits of user priority, 1 bit of Canonical Format Identifier (CFI - used for encapsulating Token Ring packets so they can be
carried across Ethernet backbones), and 12 bits of VLAN ID (VID). The 3 bits of user priority are used by 802.1p. The VID
is the VLAN identifier and is used by the 802.1Q standard. Because the VID is 12 bits long, 4094 unique VLAN can be
identified.
The tag is inserted into the packet header making the entire packet longer by 4 octets. All of the information originally
contained in the packet is retained.
-43-
User’s Manual of IGT-90x
802.1Q Tag
User Priority
3 bits
TPID (Tag Protocol Identifier)
2 bytes
Destination
Address
Preamble
Source
Address
6 bytes
CFI
1 bits
12 bits
TCI (Tag Control Information)
2 bytes
Ethernet
Type
VLAN TAG
6 bytes
VLAN ID (VID)
4 bytes
2 bytes
Data
FCS
46-1500 bytes
4 bytes
The Ether Type and VLAN ID are inserted after the MAC source address, but before the original Ether Type/Length or
Logical Link Control. Because the packet is now a bit longer than it was originally, the Cyclic Redundancy Check (CRC)
must be recalculated.
Adding an IEEE802.1Q Tag
Dest. Addr.
Src. Addr.
Length/E. type
Dest. Addr.
Src. Addr.
E. type
Data
Tag
Original Ethernet
Old CRC
Length/E. type
Data
New CRC
New Tagged Packet
Priority
CFI
VLAN ID
Port VLAN ID
Packets that are tagged (are carrying the 802.1Q VID information) can be transmitted from one 802.1Q compliant network
device to another with the VLAN information intact. This allows 802.1Q VLAN to span network devices (and indeed, the
entire network – if all network devices are 802.1Q compliant).
Every physical port on a switch has a PVID. 802.1Q ports are also assigned a PVID, for use within the switch. If no VLAN
are defined on the switch, all ports are then assigned to a default VLAN with a PVID equal to 1. Untagged packets are
assigned the PVID of the port on which they were received. Forwarding decisions are based upon this PVID, in so far as
VLAN are concerned. Tagged packets are forwarded according to the VID contained within the tag. Tagged packets are
also assigned a PVID, but the PVID is not used to make packet forwarding decisions, the VID is.
Tag-aware switches must keep a table to relate PVID within the switch to VID on the network. The switch will compare the
VID of a packet to be transmitted to the VID of the port that is to transmit the packet. If the two VID are different the switch
will drop the packet. Because of the existence of the PVID for untagged packets and the VID for tagged packets,
tag-aware and tag-unaware network devices can coexist on the same network.
A switch port can have only one PVID, but can have as many VID as the switch has memory in its VLAN table to store
them.
Because some devices on a network may be tag-unaware, a decision must be made at each port on a tag-aware device
before packets are transmitted – should the packet to be transmitted have a tag or not? If the transmitting port is
connected to a tag-unaware device, the packet should be untagged. If the transmitting port is connected to a tag-aware
device, the packet should be tagged.
Default VLANs
-44-
User’s Manual of IGT-90x
The Industrial Managed Media Converter initially configures one VLAN, VID = 1, called "default." The factory default
setting assigns all ports on the Industrial Managed Media Converter to the "default". As new VLAN are configured in
Port-based mode, their respective member ports are removed from the "default."
4.5.1 VLAN Group
This function allows disable or enable the IEEE 802.1Q VLAN operation mode. Press the “Apply” button to save the
current configuration of Industrial Managed Media Converter. The screen in Figure 4-26 & 4-27 appears and Table 4-9
describes the VLAN Group object of Industrial Managed Media Converter.
Figure 4-26 VLAN Group Web Page screen
-45-
User’s Manual of IGT-90x
Figure 4-27 VLAN Group Web Page screen
The VLAN Group Web page includes the following configurable data:
VLAN Mode
Provide Disable or enable the IEEE 802.1Q VLAN operation mode. Default mode is
Disable.
Management VLAN Group
Provide define the Management VLAN group. Default mode is VLAN1.
VLAN Group
Indicate the VLAN Group from 1 to 16.
VID
Provide define the VLAN Group ID and the available options are 1 to 4094.
Member
Apply Button
TP
Provide assign TP port into VLAN Groups.
Fiber
Provide assign Fiber port into VLAN Groups.
Press this button for save current configuration of Industrial Managed Media Converter.
Table 4-9 Descriptions of the VLAN Group Web Page Screen Objects
When change the Management VLAN Group setting, please assure the TP or fiber port that connect to
administrator PC is in the same VLAN Group, otherwise, for further managed is impossible. The only
solution is press the reset button 10 seconds for system reset to default mode.
-46-
User’s Manual of IGT-90x
4.5.2 VLAN Per Port Setting
This function provides IEEE 802.1Q VLAN per port setting for TP and Fiber port of IGT-90X. Press the “Apply” button to
save the current configuration of IGT-90X. The screen in Figure 4-28 appears and Table 4-10 describes the VLAN Per
Port Setting object of Industrial Managed Media Converter.
Figure 4-28 VLAN Per Port Setting Web Page screen
The VLAN Per Port Setting Web page includes the following configurable data:
Port
Indicate the TP port and Fiber port.
Egress Link Type
Provide Egress Link Type options for TP port and Fiber port, the available options are:
• UnTag
• Tag
• ByPass
Default mode is UnTag.
PVID
Provide PVID assign for TP port and Fiber port, the available options are 1 to 4094.
Default mode is 1 to 16.
Accept Frame Type
Provide define the Accept Frame Type and the available options are
• All
• Tagged Only
Default mode is All.
Ingress Filter
Provide disable or enable the Ingress Filter function. Default mode is Enable.
Apply Button
Press this button for save current configuration of Industrial Managed Media Converter.
Table 4-10 Descriptions of the VLAN Per Port Setting Web Page Screen Objects
-47-
User’s Manual of IGT-90x
4.5.3 Q-in-Q VLAN Setting
When enable Q-in-Q function, IGT-90X can insert or remove 4-bytes Q-in-Q tag in the received 802.3 frames after SA.
User can define Q-in-Q tag value freely. And in default condition, Q-in-Q tag format is same as VLAN tag.
In normal application, enable two port’s Q-in-Q function. UTP Port set to insert Q-in-Q tag and Fiber port set to remove
Q-in-Q Tag. For aggregation layer switch, it will check Q-in-Q tag only, not care about the VLAN tag from the corridor layer
switch. Q-in-Q Tag ether type can be set same as VLAN tag ether type or other values.
This function provides IEEE 802.1Q Q-in-Q VLAN setting of IGT-90X. Press the “Apply” button to save the current
configuration. The screen in Figure 4-29 appears and Table 4-11 describes the Q-in-Q VLAN setting object of IGT-90X.
Figure 4-29 Q-in-Q VLAN setting Web Page screen
The Q-in-Q VLAN setting Web page includes the following configurable data:
Q-in-Q Enable
Provide disable or enable the Q-in-Q VLAN function. Default mode is Disable.
Q-in-Q Direction
Provide two directions for Q-in-Q function, the available options are:
UTP is customer port, Fiber is main port
Fiber is customer port, UTP is main port
Default mode is UTP is customer port, Fiber is main port.
Out Layer VLAN Tag
EtherType (HEX)
Allow defined the Out Layer VLAN Tag Ether Type and default mode is
0x8100.
Out Layer VLAN VID (DEC)
Allow defined the Out Layer VLAN VID and default mode is 1.
Apply Button
Press this button for save current configuration of IGT-90X.
Table 4-11 Descriptions of the Q-in-Q VLAN setting Web Page Screen Objects
-48-
User’s Manual of IGT-90x
4.6 Quality of Service
Quality of Service (QoS) is an advanced traffic prioritization feature that allows you to establish control over network traffic.
QoS enables you to assign various grades of network service to different types of traffic, such as multi-media, video,
protocol-specific, time critical, and file-backup traffic.
QoS reduces bandwidth limitations, delay, loss, and jitter. It also provides increased reliability for delivery of your data and
allows you to prioritize certain applications across your network. You can define exactly how you want the switch to treat
selected applications and types of traffic.
You can use QoS on your system to:
。
Control a wide variety of network traffic by:
。
Classifying traffic based on packet attributes.
。
Assigning priorities to traffic (for example, to set higher priorities to time-critical or business-critical applications).
。
Applying security policy through traffic filtering.
。
Provide predictable throughput for multimedia applications such as video conferencing or voice over IP by
minimizing delay and jitter.
。
Improve performance for specific types of traffic and preserve performance as the amount of traffic grows.
。
Reduce the need to constantly add bandwidth to the network.
。
Manage network congestion.
This function provides Quality of Service setting of IGT-90X. Press the “Apply” button to save the current configuration.
The screen in Figure 4-30 appears and Table 4-12 describes the Quality of Service object of IGT-90X.
Figure 4-30 Quality of Service Web Page screen
The Quality of Service Web page includes the following configurable data:
QoS Mode
Provide 4 different QoS mode for operation, the available options are:
-49-
User’s Manual of IGT-90x
Disable
802.1p Tag Priority
The 802.1p Tag Priority field as show in Figure 4-31.
IP Address Priority
The IP Address Priority field as show in Figure 4-32.
IP DSCP Priority
The IP DSCP Priority field as show in Figure 4-33.
Default mode is Disable.
Scheduling
Provide two scheduling method for Quality of Service, the available options are:
Strict Priority
Weighted Round Robin (16:8:4:1)
Default mode is Strict Priority.
Apply Button
Press this button for save current configuration of IGT-90X.
Table 4-12 Descriptions of the Quality of Service Web Page Screen Objects
Figure 4-31 802.1p Tag Priority Web Page screen
-50-
User’s Manual of IGT-90x
Figure 4-32 IP Address Priority Web Page screen
Figure 4-33 IP DSCP Priority Web Page screen
-51-
User’s Manual of IGT-90x
On the top of DSCP Value table have two could be set. The default DSCP value is 63. These two fields
are both for customize DSCP value.
4.7 OAM Setup
4.7.1 Local TS-1000 OAM Setup
This function provides Local TS-1000 OAM Setup of IGT-90X. Press the “Apply” button to save the current configuration
of Industrial Managed Media Converter. The screen in Figure 4-34 appears and Table 4-13 describes the Local TS-1000
OAM Setup object of Industrial Managed Media Converter.
Figure 4-34 Local TS-1000 OAM Setup Web Page screen
The Local TS-1000 OAM Setup Web page includes the following configurable data:
TS-1000 OAM State
Provide disable or enable the TS-1000 OAM operation mode. Default mode is Disable.
TS-1000 Mode
Provide two TS-1000 modes for operation, the available options are:
Terminal
Center
Default mode is Terminal.
Link Transparent
Provide disable or enable the Link Transparent function. Default mode is Disable.
Link Transparent Result
Display the link transparent result.
Apply Button
Press this button for save current configuration of Industrial Managed Media Converter.
Table 4-13 Descriptions of the Local TS-1000 OAM Setup Web Page Screen Objects
-52-
User’s Manual of IGT-90x
4.7.2 Remote TS-1000 OAM Setup
The Remote TS-1000 OAM Setup is an advanced remote device monitor feature that allows you to remote monitor and
automatic notify status indication.
Remote monitor
1. User instructs center Media Converter to issue a status notification request frame defined in TS-1000 to get status of
terminal Media Converter.
2. Terminal Media Converter receives the status notification request frame and sends out status response frame, which
carries its current status.
Autonomous notification
1. Terminal Industrial Media Converter notifies the center Industrial Media Converter autonomously with a status
notification indication, if any change occurs in the status monitored internally by the terminal Industrial Media Converter.
2. Center Industrial Media Converter if support Option A, notifies the terminal Industrial Media Converter autonomously
with a status notification indication, if any change occurs in the status monitored internally by the Industrial center Media
Converter.
This function provides Remote TS-1000 OAM Setup of Industrial Managed Media Converter. Press the “Apply” button to
save the current configuration of Industrial Managed Media Converter. The screen in Figure 4-35 & 4-36 appears.
Figure 4-35 IGT-80x Remote TS-1000 OAM Setup Web Page screen
-53-
User’s Manual of IGT-90x
Figure 4-36 IGT-90X Remote TS-1000 OAM Setup Web Page screen
Please use the PLANET GT-80X / GT-90X / IGT-90X as the Remote device.
-54-
User’s Manual of IGT-90x
4.7.3 TS-1000 Loop Back Test
The TS-1000 Loop Back Test allows manual run this loop back test to check the interconnection between two Industrial
Media Converter devices. To assure the Remote TS-1000 OAM function can work correctly.
In-band and out-band Loop back
1. Instruct center Industrial Media Converter to issue an OAM frame to request a loop back test. Terminal return start
response OAM frame to center Media Converter.
2. Terminal Media Converter runs at loop back mode.
3. Central Media Converter send test frame and terminal Media Converter loop back the frames. Test frame can be
generated from central Industrial Media Converter’s UTP port (Out-Band) or from central Industrial Media Converter
(In-Band) automatically.
4. Center Industrial Media Converter check the loop back test result after sending all test frames
5. Instruct the central Industrial Media Converter to end loop back test.
This function provides TS-1000 Loop Back Test of Industrial Managed Media Converter. Press the “Apply” button to run
Loop Back Test and see the TS-1000 Loop Back Test Result of Industrial Managed Media Converter, also press the
“Refresh” button to renew the Web screen. The screen in Figure 4-37 appears and Table 4-14 describes the TS-1000
Loop Back Test object of Industrial Managed Media Converter.
-55-
User’s Manual of IGT-90x
Figure 4-37 Remote TS-1000 Loop Back Test Web Page screen
The TS-1000 Loop Back Test Web page includes the following configurable data:
TS-1000 Loop Back Test
Send Packet Number
Allow input the number for packet send and the available options is 1 to 255. Default is
16.
Apply Button
Press this button for save current configuration of Industrial Managed Media
Converter.
Refresh Button
Press “Refresh” button to refresh current status.
TS-1000 Loop Back Test Result
Result
Display the TS-1000 Loop Back Test Result. Fail or Pass.
Result counter
Display the value of Counter Result.
Table 4-14 Descriptions of the TS-1000 Loop Back Test Web Page Screen Objects
Please use the PLANET GT-80X / GT-90X / IGT-90X as the Remote device.
-56-
User’s Manual of IGT-90x
4.7.4 802.3ah Setup
When enable 802.3ah OAM function, all 802.3ah OAMPDU packets will trap to embedded CPU.
Software will implement auto discovery procedure. With hardware support, software controls the 802.3ah remote loop
back procedure. Hardware can also detect dying gasp even and interrupt CPU to send dying gasp even notification
OAMPDU. All other functions defined by 802.3ah are implemented using embedded CPU.
When remote device is in loop back mode, hardware can support change looped test frame’s DA, SA or both as user
defined. Hardware can also set to don't change looped test frame.
This function provides 802.3ah Setup of Industrial Managed Media Converter. Press the “Apply” button to save the
current configuration of Industrial Managed Media Converter. The screen in Figure 4-38 appears and Table 4-15
describes the 802.3ah Setup object of Industrial Managed Media Converter.
Figure 4-38 802.3ah Setup Web Page screen
The 802.3ah Setup Web page includes the following configurable data:
802.3ah OAM State
Provide disable or enable the 802.3ah OAM State function. Default mode is Enable.
802.3ah OAM Mode
Allow to choose “Active” or “Passive” for 802.3ah OAM Mode. Default mode is
Passive.
Loopback Reply
Provide disable or enable the Loopback Reply function. Default mode is Enable.
Remote OAM Configure
Provide disable or enable the Remote OAM Configure function. Default mode is
Enable.
Remote OAM Configuration
Result
Display the Remote OAM Configuration Result.
Apply Button
Press this button for save current configuration of Managed Media Converter.
Table 4-15 Descriptions of the 802.3ah Setup Web Page Screen Objects
1. The 802.3ah function must work with manageable device that supports 802.3ah function.
2. Please use the PLANET GT-80X / GT-90X / IGT-90X as the Remote device.
-57-
User’s Manual of IGT-90x
4.7.5 802.3ah Loop Back Test
The 802.3ah Loop Back Test allows manual run this loop back test to check the interconnection between two Industrial
Media Converter devices. To assure the Remote 802.3ah function can work correctly.
This function provides 802.3ah Loop Back Test of Industrial Managed Media Converter. Press the “Apply” button to run
802.3ah Loop Back Test and see the 802.3ah Loop Back Test Result of Industrial Managed Media Converter, also press
the “Refresh” button to renew the Web screen. The screen in Figure 4-39 appears and Table 4-16 describes the 802.3ah
Loop Back Test object of Industrial Managed Media Converter.
Figure 4-39 802.3ah Loop Back Test Web Page screen
-58-
User’s Manual of IGT-90x
The 802.3ah Loop Back Test Web page includes the following configurable data:
802.3ah Loop Back Test
Send Packet Number
Allow input the number for packet send and the available options is 1 to 255.
Default is 16.
Packet Length
(Not include CRC)
Allow input the number for Packet Length and the available options is 60 to 1514.
Default is 60.
Apply Button
Press this button for save current configuration of Industrial Managed Media
Converter.
Refresh Button
Press “Refresh” button to refresh current status.
802.3ah Loop Back Test Result
Result
Display the 802.3ah Loop Back Test Result. Fail or Pass.
Table 4-16 Descriptions of the 802.3ah Loop Back Test Web Page Screen Objects
1. The 802.3ah function must work with manageable device that supports 802.3ah function.
2. Please use the PLANET GT-80X / GT-90X / IGT-90X as the Remote device.
-59-
User’s Manual of IGT-90x
4.8 Security
This function provides TCP / UDP Filter setting of Industrial Managed Media Converter. Press the “Apply” button to save
the current configuration of Industrial Managed Media Converter. The screen in Figure 4-40 appears and Table 4-17
describes the TCP / UDP Filter setting object of Industrial Managed Media Converter.
Figure 4-40 Security setting Web Page screen
The Quality of Service Web page includes the following configurable data:
Group ID
Provide input the group ID for TCP / UDP Filter and the available range is 1 to 16.
Action
Provide “Deny” or “Permit” options and default mode is Permit.
Egress Port
Provide choose “TP” or “Fiber” as Egress Port. Default mode is TP.
Packet Type
Provide IPv4 and Non-IPv4 protocol for further setting.
L4 Protocol
Provide IPv4 and Non-IPv4 protocol for further setting.
IPv4: TCP Any / FTP (21) / HTTP (80), UDP Any / TFTP (69)
Non-IPv4: Any / ARP (0x0806) / IPX (0X8137)
Current List
Display current TCP / UDP Filter Groups.
Add Button
Press this button for add new TCP / UDP Filter group into current list.
Del Button
Press this button for delete existence TCP / UDP Filter group from current list.
Table 4-17 Descriptions of the Security setting Web Page Screen Objects
-60-
User’s Manual of IGT-90x
4.9 Logout
This function provides Logout function of Industrial Managed Media Converter, when the “Are you sure to logout” pop
window appears; press the “OK” button to logout Web page of Industrial Managed Media Converter. The screen in Figure
4-41 & 4-42 appears.
Figure 4-41 Logout Web Page screen
Figure 4-42 Login Web Page screen
-61-
User’s Manual of IGT-90x
5. TROUBLE SHOOTING
This chapter contains information to help you solve problems. If the media converter is not functioning properly, make sure
the media converter was set up according to instructions in this manual.
The Link LED is not lit
Solution:
1.
Check the cable connection and remove duplex mode of the Industrial Managed Media Converter.
2.
Check the port configuration of the link partner; make sure the two side devices with the same link
configuration.
Performance is bad
Solution:
Check the full duplex status of the device. If the device is set to full duplex and the partner is set to half duplex, then
the performance will be poor.
10/100/1000Base-T port link LED is lit, but the traffic is irregular
Solution:
Check that the attached device is not set to dedicate full duplex. Some devices use a physical or software switch to
change duplex modes. Auto-negotiation may not recognize this type of full-duplex setting.
Why the device doesn’t connect to the network
Solution:
Check the LNK/ACT LED on the Industrial Managed Media Converter .Try another port on the connected device.
Make sure the cable is installed properly Make sure the cable is the right type Turn off the power. After a while, turn on
power again.
How to deal forgotten password situation of device?
Solution:
The Industrial Managed Media Converter is implemented with “Reset” button, press the button at the front panel
about 10 seconds. After the device is booted then login the Web Management page with default user name and
password (admin).
Hardware Reset
Button
-62-
User’s Manual of IGT-90x
APPENDIX A NETWORKING CONNECTION
A.1 Device‘s RJ-45 Pin Assignments
■
1000Mbps, 1000Base T
RJ-45 Connector pin assignment
Contact
MDI
MDI-X
1
BI_DA+
BI_DB+
2
BI_DA-
BI_DB-
3
BI_DB+
BI_DA+
4
BI_DC+
BI_DD+
5
BI_DC-
BI_DD-
6
BI_DB-
BI_DA-
7
BI_DD+
BI_DC+
8
BI_DD-
BI_DC-
10/100Mbps, 10/100Base-TX
RJ-45 Connector pin assignment
MDI
MDI-X
Contact
Media Dependant
Interface
Media Dependant
Interface -Cross
1
Tx + (transmit)
Rx + (receive)
2
Tx - (transmit)
Rx - (receive)
3
Rx + (receive)
Tx + (transmit)
4, 5
6
7, 8
Not used
Rx - (receive)
Tx - (transmit)
Not used
A.2 RJ-45 Cable Pin Assignment
The standard RJ-45 receptacle/connector
There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation
and color of straight cable and crossover cable connection:
-63-
User’s Manual of IGT-90x
Straight Cable
1
2
3
4
5
6
SIDE 1
7
8
SIDE 1
SIDE 2
1
2
3
4
5
6
7
8
1 = White / Orange
1 = White / Orange
2 = Orange
2 = Orange
3 = White / Green
3 = White / Green
4 = Blue
4 = Blue
5 = White / Blue
5 = White / Blue
6 = Green
6 = Green
7 = White / Brown
7 = White / Brown
8 = Brown
8 = Brown
Straight Cable
1
2
3
4
5
6
SIDE 1
7
8
SIDE 1
SIDE 2
1
2
3
4
5
6
SIDE2
7
8
SIDE2
1 = White / Orange
1 = White / Orange
2 = Orange
2 = Green
3 = White / Green
3 = White / Orange
4 = Blue
4 = Blue
5 = White / Blue
5 = White / Blue
6 = Green
6 = Orange
7 = White / Brown
7 = White / Brown
8 = Brown
Figure A-1: Straight-Through and Crossover Cable
8 = Brown
Please make sure your connected cables are with same pin assignment and color as above picture before deploying the
cables into your network.
A.3 Fiber Optical Cable Connection Parameter
The wiring details are as below:
■
Fiber Optical patch Cables:
Standard
Fiber
1000Base-SX Multi-mode
1000Base-LX
Multi-mode
Single-mode
Diameter (micron)
Modal Bandwidth
Max. Distance
(MHz * km)
(meters)
62.5
100
220
62.5
200
275
50
400
500
50
500
550
62.5
5
550
50
4
50
5
9
N/A
2080-AA1130-002
-64-
5000*
EC Declaration of Conformity
For the following equipment:
*Type of Product
*Model Number
: Industrial Managed Gigabit Ethernet Media Converter
: IGT-902, IGT-902S, IGT-905A, IGT-902T, IGT-902TS
* Produced by:
Manufacturer‘s Name
: Planet Technology Corp.
Manufacturer‘s Address : 11F, No. 96, Min Chuan Road, Hsin Tien,
Taipei, Taiwan, R.O.C.
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
Directive on (2004/108/EC).
For the evaluation regarding the EMC, the following standards were applied:
Emission
Harmonic
Flicker
Immunity
ESD
RS
EFT/ Burst
Surge
CS
Magnetic Field
Voltage Disp
EN 55022
EN 61000-3-2
EN 61000-3-3
EN 55024
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
IEC 61000-4-11
(CLASS A: 2006 + A1:2007)
(2006)
(1995 + A1:2001 + A2:2005)
(1998 + A1:2001 + A2:2003)
(2001)
(2008)
(2004)
(2005)
(2008)
(2001)
(2004)
Responsible for marking this declaration if the:
⌧ Manufacturer
Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name:
Planet Technology Corp.
Company Address:
11F, No.96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C
Person responsible for making this declaration
Name, Surname
Kent Kang
Position / Title :
Product Manager
Taiwan
Place
16 th, March., 2010
Date
Legal Signature
PLANET TECHNOLOGY CORPORATION
e-mail: sales@planet.com.tw
http://www.planet.com.tw
11F, No. 96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C. Tel:886-2-2219-9518 Fax:886-2-2219-9528
Download PDF
Similar pages