DATA PROJECTOR
Operations
Maintenance
(SVGA/ With Document Camera)
Preparations
(SVGA)
Others
TDP-S80
TDP-S81
Before Using
OWNER’S MANUAL
Before Using
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended
to alert the user to the presence of uninsulated "dangerous voltage" within the product's
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES
ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET.
REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
WARNING: Handling the cord on this product or cords associated with accessories sold with
USA only this product, will expose you to lead, a chemical known to the State of California
to cause birth defects or other reproductive harm. Wash hands after handling.
WARNING: This [product] contains mercury. Disposal of mercury may be regulated due to
USA only environmental considerations. For disposal or recycling information, please
contact your local authorities or the Electronic Industries Alliance: www.eiae.org.
MODEL NAME: TDP-S80
USA only
TRADE NAME: DATA PROJECTOR
Tested To Comply
With FCC Standards
MODEL NAME: TDP-S80
FOR HOME OR OFFICE USE
FCC NOTICE: This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
2
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
RESPONSIBLE PARTY: TOSHIBA AMERICA INFORMATION SYSTEMS, INC.
9740 Irvine Blvd., Irvine, CA 92618-1697 U.S.A
Phone: (949) 583-3000
WARNING:
USA only
Changes or modifications made to this equipment, not expressly approved
by Toshiba, or parties authorized by Toshiba, could void the user’s authority
to operate the equipment.
Notice:
CANADA only
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil
numérique de la classe B est conforme à la norme NMB-003 du Canada.
MODEL NAME: TDP-S81
FCC Radio Frequency Interference Statement
Note:
This equipment has been tested and found to comply with the limits for a Class
USA only A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiates radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the
interference at his own expense.
WARNING: Changes or modifications made to this equipment, not expressly approved by
USA only Toshiba, or parties authorized by Toshiba, could void the user’s authority to operate
the equipment.
Notice:
This Class A digital apparatus complies with Canadian ICES-003. Cet appareil
CANADA only numérique de la classe A est conforme à la norme NMB-003 du Canada.
WARNING: This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
3
Before Using
SAFETY PRECAUTIONS
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND
INSTRUCTIONS GIVEN IN THIS OWNER'S MANUAL AND THOSE
MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE
REFERENCE.
This set has been designed and manufactured to assure personal safety. Improper use can
result in electric shock or fire hazard. The safeguards incorporated in this unit will protect you
if you observe the following procedures for installation, use and servicing. This unit is fully
transistorized and does not contain any parts that can be repaired by the user.
5. Heat
8. Power-Cord Protection
The product should be situated
away from heat sources such as
radiators, heat registers, stoves, or
other products (including
amplifiers) that produce heat.
Power-supply cords should be
routed so that they are not likely to
be walked on or pinched by items
placed upon or against them,
paying particular attention to cords
at plugs, convenience receptacles,
and the point where they exit from
the product.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO
DANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL ONLY.
1. Read Owner's Manual
3. Source of Light
After unpacking this product, read
the owner's manual carefully, and
follow all the operating and other
instructions.
Do not look into the lens while the
lamp is on. The strong light from
the lamp may cause damage to
your eyes or sight.
6. Water and Moisture
Do not use this product near water.
- for example, near a bath tub,
wash bowl, kitchen sink, or laundry
tub; in a wet basement; or near a
swimming pool and the like.
9. Overloading
Do not overload wall outlets;
extension cords, or integral
convenience receptacles as this
can result in a risk of fire or
electric shock.
4. Ventilation
2. Power Sources
Openings in the cabinet are
provided for ventilation and to
ensure reliable operation of the
product and to protect it from
overheating, and these openings
must not be blocked or covered.
The openings should never be
blocked by placing the product on
a bed, sofa, rug or other similar
surface. This product should not
be placed in a built-in installation
such as a bookcase or rack unless
proper ventilation is provided or
the manufacturer's instructions
have been adhered to.
This product should be operated
only from the type of power source
indicated on the marking label.
If you are not sure of the type of
power supply to your home,
consult your product dealer or
local power company.
For products intended to operate
from battery power, or other
sources, refer to the operating
instructions.
4
7. Cleaning
Unplug this product from the wall
outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners.
Use a soft cloth for cleaning.
5
Before Using
IMPORTANT SAFETY INSTRUCTIONS
10. Lightning storms
12. Do not place the product
vertically
For added protection for this
product during storm, or when it is
left unattended and unused for
long periods of time, unplug it from
the wall outlet. This will prevent
damage to the product due to
lightning and power-line surges.
However, while it is thundering or
lightning, do not touch the
apparatus and any connected
cable and/or equipment.
This will prevent you from
receiving the electric shock by an
electric surge.
Do not use the product in the
upright position to project the
pictures at the ceiling, or any other
vertical positions. It may fall down
and dangerous.
e) If the product has been dropped or
damaged in any way.
f) When the product exhibits a
distinct change in performance this indicates a need for service.
15. Accessories
Do not place this product on an
unstable cart, stand, tripod,
bracket, or table. The product may
fall, causing serious injury to a
child or adult, and serious damage
to the product. A product and cart
combination should be moved with
care. Quick stops, excessive
force, and uneven surfaces may
cause the product and cart
combination to overturn.
17. If glass components,
including lens and lamp,
should break, contact your
dealer for repair service.
This product incorporates glass
components, including a lens and
a lamp. If such parts should
break, please handle with care to
avoid injury and contact your
dealer for repair service. The
broken pieces of glass may cause
to injury. In the unlikely event of
the lamp rupturing, thoroughly
clean the area around the
projector and discard any edible
items placed in that area.
13. Stack Inhibited
Do not stack other equipment on
this product or do not place this
product on the other equipment.
Top and bottom plates of this
product develops heat and may
give some undesirable damage to
other unit.
11. Object and Liquid Entry
Never push objects of any kind
into this product through openings
as they may touch dangerous
voltage points or short-out parts
that could result in a fire or electric
shock. Never spill liquid of any
kind on the product.
14. Attachments
Do not use attachments not
recommended by the product
manufacturer as they may cause
hazards.
6
S3125A
16. Damage Requiring Service
Unplug this product from the wall
outlet and refer servicing to
qualified service personnel under
the following conditions:
a) When the power-supply cord or
plug is damaged.
b) If liquid has been spilled, or
objects have fallen into the
product.
c) If the product has been exposed to
rain or water.
d) If the product does not operate
normally by following the operating
instructions. Adjust only those
controls that are covered by the
operating instructions as an
improper adjustment of other
controls may result in damage and
will often require extensive work by
a qualified technician to restore
the product to its normal
operation.
18. Servicing
Do not attempt to service this
product yourself as opening or
removing covers may expose you
to dangerous voltage or other
hazards. Refer all servicing to
qualified service personnel.
7
Before Using
IMPORTANT SAFETY INSTRUCTIONS (Continued)
19. Replacement Parts
22. Do not get your hands
between the camera arm
and the main unit when
setting the camera arm
back in its original
position. (Models equipped
When replacement parts are
required, be sure the service
technician has used replacement
parts specified by the
manufacturer or have the same
characteristics as the original part.
Unauthorized substitutions may
result in fire, electric shock, or
other hazards.
(Replacement of the lamp only
should be made by users.)
with document camera)
To avoid injury, be careful not to
get your hands caught when
setting the camera arm back in its
original position.
Families with children should be
particularly careful.
20. Safety Check
Upon completion of any service or
repairs to this product, ask the
service technician to perform
safety checks to determine that
the product is in proper operating
condition.
23. Do not carry by the camera
arm. (Models equipped with
document camera)
Do not carry the projector by the
camera arm. Doing so can result
in damage or injury.
24. Do not move the projector
while the arm is still erect.
(Models equipped with
document camera)
Always store the arm back in
position when moving the
projector. Otherwise injury or
damage may result.
21. Do not leave thermalpaper documents or easily
deformed items on top of
the unit or near the air
exhaust for long periods
of time.
25. Do not use the product in a
closed installation state.
The heat from the unit could erase
the information on the thermal
paper, or cause deformation or
warping.
Do not place the product in a box
or in any other closed installation
state. Otherwise it may overheat.
This could result in a risk of fire.
8
POWER SUPPLY CORD SELECTION
If your line voltage is 220 to 240V, use one of the following types of cable.
Plug
configuration Plug type
Plug
configuration
Line voltage
EURO
220 – 240V
UK
220 – 240V
Use a 5A fuse which is approved by ASTA
or BSI to BSI362.
Always replace the fuse cover after
changing the fuse.
Plug type
Line voltage
Australian
240V
10A
200 – 240V
Switzerland
240V
6A
200 – 240V
North American 200 – 240V
240V
15A
IMPORTANT PRECAUTIONS
Save Original Packing Materials
The original shipping carton and packing materials will come in handy if you ever have to
ship your projector. For maximum protection, repack the set as it was originally packed at
the factory.
Moisture Condensation
Never operate this unit immediately after moving it from a cold location to a warm location.
When the unit is exposed to such a change in temperature, moisture may condense on
the crucial internal parts. To prevent the unit from possible damage, do not use the unit for
at least 2 hours when there is an extreme or sudden change in temperature.
Place and Manner of Installation
• Do not place in hot locations, such as near heating equipment. Doing so could cause
malfunction, and shorten the life of the projector.
• Avoid locations with oil or cigarette smoke. Doing so will dirty the optical parts,
shortening their lives, and darkening the screen.
• Do not use the product vertically in any upright position or slantwise in an angle of 20
degrees or more.
• Using this instrument near a TV or radio may cause interference to the images or audio
sound. If this happens, move it away from the TV or radio.
• Moving the projector from a low-temperature room to a high-temperature room may
cause condensation on the lens or internal parts in the instrument. If you continue to use
it in that situation, the malfunction may result. Ensure to wait until the condensation
naturally disappears.
• In a high altitude location where air is thin, cooling efficiency is reduced so use it with the
ambient temperature being lowered.
9
Before Using
IMPORTANT SAFETY INSTRUCTIONS (Continued)
OTHER CAUTIONS AND INFORMATIONS
Avoid Volatile Liquid
Copyrights
Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or
plastic products touching the unit for a long time. They will leave marks on the finish.
If cleaning with a chemically saturated cloth, be sure to follow the product's precautions.
In the spaces provided below, record the Model and Serial No. located at the bottom of your
projector.
Model No.
Serial No.
Showing or transmitting commercial imaging software or broadcast or cable-broad
casting programs with the purpose of other than the personal and private viewing,
including modifying images using the freeze or resize functions, or displaying with the
varying aspect ratio of the images, could violate the direct or indirect copyrights of the
imaging software or broadcast program, etc., if done without first consulting with the
copyright holder. For this reason, please take appropriate measures before performing
one of the actions listed above, including obtaining a license from the copyright holder.
Disposal
This product contains substances which are harmful to humans and the environment.
• Solder used in the internal parts contains the lead.
• The lamp contains inorganic mercury.
Please dispose of this product or used lamps in accordance with local regulations.
Retain this information for future reference.
Trademarks
EXEMPTION CLAUSES
• Toshiba Corporation bears no responsibility in the case of damages arising from natural
disaster such as earthquakes, lightning, etc., fire not liable to Toshiba Corporation,
operation, theft or mischief by third parties, other accidents, or use under abnormal
conditions including erroneous or improper operation and other problems.
• Toshiba Corporation bears no responsibility for incidental damages (lost profit, work
interruption, corruption or loss of the memory contents, etc.) arising from the use of or the
inability to use this unit.
• Toshiba Corporation accepts no liability whatsoever for any damages arising from not
having followed the descriptions in this Instruction Manual.
• Toshiba Corporation accepts no liability whatsoever for any damages arising from
malfunctions arising from combination with equipment or software that is not related to
Toshiba Corporation.
• VGA, SVGA, XGA, SXGA, UXGA are trademarks or registered trademarks of
International Business Machines Corporation.
• Digital Light Processing, Digital Micromirror Device and DMD are trademakes of Texas
Instruments.
• Macintosh is a registered trademark of Apple Computer, Inc.
• Windows is a registered trademark of Microsoft Corporation in the U.S. and other
countries.
• Adobe is a registered trademark and Acrobat Reader is a trademark of Adobe Systems
Incorporated.
Notational Conventions Used in This Manual
• References to pages with related information are annotated as follows.
For example, if making a reference to page 36: p.36
• The illustrations in this document are for reference purposes only and may not reflect
your package exactly.
REMOTE CONTROL BATTERIES
Be sure to use AA size batteries.
Do not reverse the polarity when inserting the battery.
Do not recharge, heat, disassemble, short-circuit, or burn the battery.
Do not use the battery beyond the expiration date indicated on the battery or leave a
dead battery in the remote control.
• Do not mix batteries of different types, such as alkaline and manganese. Do not mix new
and used batteries.
Using the batteries improperly may cause them to explode or leak and lead to burn or injury. If
battery-leaking fluid contacts skin, wash the fluid off immediately with clean water and consult a
doctor. If the fluid is spilt on an instrument, avoid contact and wipe it off using tissue paper.
(Dispose of the used tissue paper as flammable garbage after moistening with water.)
•
•
•
•
10
11
Before Using
IMPORTANT PRECAUTIONS (Continued)
Before Using
Others
SAFETY PRECAUTIONS ..................................................................................
IMPORTANT SAFETY INSTRUCTIONS ...........................................................
POWER SUPPLY CORD SELECTION .............................................................
IMPORTANT PRECAUTIONS ...........................................................................
EXEMPTION CLAUSES ....................................................................................
OTHER CAUTIONS AND INFORMATIONS ......................................................
REMOTE CONTROL BATTERIES ....................................................................
CONTENTS .......................................................................................................
2
4
9
9
10
11
11
12
Preparations
Checking the package contents .........................................................................
Names of each part on the main unit .................................................................
Names of each part on the control panel and remote control ............................
Parts on the rear panel ......................................................................................
Names of each part on the document camera (TDP-S81) ................................
Preparing and using the remote control .............................................................
Placement ..........................................................................................................
Connection .........................................................................................................
14
15
16
17
18
19
20
21
Trouble indications .............................................................................................
Before calling service personnel ........................................................................
Specifications .....................................................................................................
List of general specifications ..........................................................................
Document camera specifications (TDP-S81) .................................................
List of supported signals (RGB signals) .........................................................
List of supported signals (Y/PB/PR signals) ....................................................
List of supported signals (Video, S-Video signals) .........................................
Pin assignment of COMPUTER-1/2 & MONITOR terminals ..........................
CONTROL terminal ........................................................................................
Separately sold product ..................................................................................
Operations
Turning the power on and off .............................................................................
Basic operations ................................................................................................
Using handy features .........................................................................................
Using auto setting ...........................................................................................
Cutting off the picture and sound temporarily (Mute) .....................................
Freezing the image (Freeze) ..........................................................................
Using the menus ................................................................................................
How to use the menus ....................................................................................
The image adjustment menu ..........................................................................
The display setting menu ...............................................................................
The default setting menu ................................................................................
Displaying Information (Status display) ..........................................................
Using the document camera ..............................................................................
How to use the document camera ..................................................................
Image projection with the document camera ..................................................
Locking the white balance ..............................................................................
22
24
26
26
28
28
29
29
30
31
32
33
34
34
36
37
Maintenance
About lamp ......................................................................................................... 38
Lamp replacement ............................................................................................. 38
Lens and main unit cleaning .............................................................................. 40
12
13
41
42
44
44
44
45
46
46
46
47
47
Before Using
CONTENTS
Preparations
Checking the package contents
Names of each part on the main unit
Please make sure that the following items are included in the box, along with the main unit. If
any item is missing, please contact the store immediately where you purchased the product.
(4)
(2)
(5)
(3)
(6)
(5)
(4)
(3) (2)(1)
(7)
(8)
(8)
■ (1) Remote control
■ (2) R6 (SIZE AA) batteries for remote control (2)
■ (3) CD-ROM
■ (4) Owner’s Manual
■ (5) Power cord (See note)
■ (6) RGB cable (3m)
■ (7) Carrying bag
■ (8) RGB cable (25cm)*
*: Supplied with TDP-S81.
Note
The shape and number of supplied power cords vary depending on the product destination.
◆The Supplied CD-ROM
The supplied CD-ROM contains an owner’s manual, including information not available for
the printed Owner’s manual (Getting started) and Acrobat® Reader™ to view the manual.
■ Installing Acrobat® Reader™
Windows®: Run the CD-ROM, select the Reader/English folder, and run ar500enu.exe.
Follow the on-screen instructions.
Macintosh: Run the CD-ROM, select the Reader/English folder, and run Reader
Installer. Follow the on-screen instructions to install the software.
(9)
(11)(9) (12) (13)
(10)
Back
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
Front
Name
: Function
Foot adjuster release button
Infrared remote sensor
Lens
Air intake
Speaker
Control panel
Zooming lever
Air exhaust
Tilt adjuster
Rear panel
Focusing lever
Foot adjuster
Lamp cover
:
:
:
:
:
:
:
:
:
:
:
:
:
Press to stow the foot adjuster. p.25
Senses commands from the remote control. p.19
Projects expanded image.
Draws in air from outside the projector.
Outputs audio sound.
Operates the projector. p.16
Adjusts screen size. p.25
Expels air that has grown hot inside the projector.
Adjusts the projector’s horizontal tilt. p.25
Connects external devices. p.17
Adjusts screen focus. p.25
Adjusts the vertical projection angle. p.25
Remove to replace lamp. p.39
■ Viewing the manual
Run the CD-ROM and double-click on Start.pdf. Acrobat® Reader™ launches, and the
menu screen of the Owner’s manual appears. Click on your language. The Owner’s
Manual cover and list of bookmarks appear. Click on a bookmark title to view that
section of the manual. Click on p.
to view a reference page with related information.
See the Help menu for more information about Acrobat® Reader™.
14
15
Preparations
(1)
(7) (6)
Names of each part on the control panel and remote control
Control panel
Parts on the rear panel
Remote Control
(1) (2) (3) (4)
(5) (6)
(7)
(8)
(9)
Remote control
transmitter
(10)
(11)
(10)
(11)
(1)
(8)
(3)
(6)
(4)
(13)
(12)
(2)
(1)
(7)
(2)
(6)
(3)
(8)
(4)
(7)
(5)
(15)
Name
(1) Infrared remote sensor
(2) CONTROL terminal
(3) USB terminal
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
Name
: Main Function
ENTER button
MENU button
SET UP button
ON/STANDBY button
ON indicator
INPUT button
RETURN button
Selection button
LAMP indicator
TEMP indicator
FAN indicator
FREEZE button
MUTE button
:
:
:
:
:
:
:
:
:
:
:
:
:
Accepts the selected mode.
Displays menus. p.29
Sets up image and mode. p.26
Turns the power on/off (standby). p.22
Displays whether power is on or off. p.22
Selects input. p.24
Goes back one screen.
Menu selections and adjustments,etc. p.30
Displays lamp mode. p.23
Lights when internal temperature too high. p.41
Displays cooling fan mode. p.41
Pauses image. p.28
Cuts off the picture and sound temporarily. p.28
(4)
(5)
(6)
(7)
(8)
AUDIO (L/R) terminal
VIDEO terminal
AUDIO (L/R) terminal
S-VIDEO terminal
COMPUTER 1 terminal
(9) AUDIO OUT terminal
(10) MONITOR terminal
(11) COMPUTER 2 terminal
(12) Main power switch
(13) AC IN socket
(14) AUDIO IN terminal
(15) Antitheft lock hole
Note
• For the remainder of this manual, buttons are referred to as follows:
Selection buttons ⇒
; ENTER button ⇒
(14) (13) (12)
: Main Function
: Senses commands from the remote control. p.19
: When operating the projector via a computer, connect
this to the controlling computer’s RS-232C port. p.47
: Terminal for service purpose. Do not make any
connection.
: Input audio signals from video equipment.
: Input video signals from video equipment.
: Input audio signals from video equipment.
: Input S video signals from video equipment.
: Input RGB signal from a computer or other source, or a
component video signal (Y/PB/PR) from video
equipment.
: Outputs audio signals.
: Connect to a computer display, etc.
: Input RGB signal from a computer or other source, or a
component video signal (Y/PB/PR) from video
equipment.
For TDP-S81, use exclusively for document camera
connection.
: AC power line ON (standby)/OFF.
: Connect the supplied power cord here.
: Input audio signals from a computer or video
equipment with a component video signal output
terminal.
: Attach a safety cable or any other antitheft device.
Note
• Although this owner’s manual abbreviates component video signals as Y/PB/PR, the
product also supports signals from video equipment marked “Y/CB/CR.”
16
17
Preparations
(9)
Names of each part on the document camera (TDP-S81)
(12)
(1)
(8) (9)
(6)
(11)
(10)
Preparing and using the remote control
■ Loading dry-cell batteries
into the remote control
■ Operating the remote
control
q Remove the battery cover.
Point the remote control toward the
projector’s infrared remote sensor,
and press a button on the remote
control.
• Operating the projector from the front
(3)
w Insert the dry-cell batteries.
(4)
(7)
Name
(1) Tray
(2) Lock switch
(8) CAMERA button
(9)
(10)
(11)
(12)
:
:
:
:
(6) Camera arm
(7) Lock lever
Approx. 15°
App
rox
. 5m
: Function
: The document camera is mounted.
: Used when the document camera is attached/detached
to/from the tray.
: Locks the document camera onto the tray.
: Used connect the supplied document camera cable to
the COMPUTER IN (camera) terminal of the projector.
: Pulled out when a camera is used separated from the
projector.
: Adjusts the shooting angle. p.36
: Used when the document camera is detached from the
tray.
: Toggles between the camera input and previous input.
(3) Lock lever
(4) Camera output terminal
(CAMERA OUT)
(5) Tip resistant bar
Be sure to align the plus and minus
ends of the batteries properly.
• Operating the projector from the rear
Two batteries (R6, SIZE AA) are used.
e Replace the battery cover.
Approx. 15°
Ap
pro
x.
5m
p.36
CAMERA GAIN buttons
Focusing lever
Camera lens
Camera head
Adjusts the camera gain. p.36
Adjusts the focus.
Shooting lens for the document camera.
Document camera.
Dry-cell batteries
• Before using the batteries, be sure to observe the Safety Precautions described in
previous pages.
• Remove batteries from remote control when not using for extended periods.
• If the remote control stops working, or if its range decreases, replace all the batteries with
new ones.
The remote control
• The remote control may fail to operate if the infrared remote sensor is exposed to bright
sunlight or fluorescent lighting.
• Do not drop or bang.
• Do not leave in hot or humid locations.
• Do not get wet or place on top of wet objects.
• Do not take apart.
• In rare cases, ambient conditions could impede the operation of the remote control. If this
happens, point the remote control at the main unit again, and repeat the operation.
18
19
Preparations
(5)
(2)
Placement
Connection
Placement Styles
Before connection
As shown in the figures below, this device can be placed in 4 different styles.
The factory setting is “floor-mounted front projection.” Set the Projection mode in the
default setting menu p.32 , in accordance with your needs.
• Read the owner’s manual of the device you are connecting to the projector.
• Some types of computer cannot be used or connected to this projector.
Check for an RGB output terminal, supported signal p.45 , etc.
• Turn off the power of both devices before connecting.
• The figure below is a sample connection. This does not mean that all of these devices
can or must be connected simultaneously. (Dotted lines mean items can be exchanged.)
Floor-mounted rear projection
Audio amplifier, etc.
Computer (for control)
Ceiling-mounted front projection
Video recorder,
DVD player, etc.
VCR
Ceiling-mounted rear projection
To RS-232C
terminal
To audio output
p.47 White (L)/Red (R)
To video To audio output
output White (L)/Red (R)
Video cable (not supplied)
Control cable
AV cable
(not supplied)
To S-Video
output
Audio cable
(not supplied)
To audio input
White (L)/Red (R)
S-Video cable
(not supplied)
WARNING
• Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when placing the unit.
Attempting to clean/replace the lamp at a high site by yourself may cause you to drop down, thus
resulting in injury.
• If you wish to mount the projector on the ceiling, be sure to ask your dealer to do so. Mounting the
projector on a ceiling requires special ceiling brackets (sold separately) and specialized knowledge.
Improper mounting could cause the projector to fall, resulting in an accident.
• If the projector is ceiling-mounted, install the breaker for turning off the power in case of anomaly. Let
everyone involved with the use of the projector know that fact.
RGB cable
(not supplied)
Projection Distance and Size
Use the figures, tables, and formulas below to determine the projection size and projection distance.
(Projection sizes are approximate values for full-size picture with no keystone adjustment.)
Screen
Audio cable
(not supplied)
Audio cable
(not supplied)
Monitor cable Mini
D-sub 15P-BNC
(not supplied)
To RGB
output
RGB cable
(supplied with
TDP-S81)
As seen from above
To audio
output
a (min length) = projection size (inches) × 0.04064
90°
a (max length) = projection size (inches) × 0.04878
projection
size (inches)
As seen from the side
24.6
40
60
80
100
150
200
246
Lens center
H
90°
a
a is the distance (m) between the lens and the
screen, and corresponds to a range of 1.20 m to
10.00 m. H is the height from the image bottom to
the center of the lens.
20
projection distance a (m)
height (H)
min length
max length
(cm)
(zooming max) (zooming min)
—
1.20
12.8
1.62
1.95
20.2
2.44
2.93
30.0
3.25
3.90
40.2
4.06
4.88
50.3
6.10
7.32
75.4
8.13
9.76
100.6
10.00
—
123.8
Computer
To audio output
RGB cable
(supplied)
To RGB output
To Y/CB/CR output
Green (Y)/Blue (CB)/Red (CR)
Conversion adapter BNC-pin
(not supplied)
DVD video recorder, etc.
Document camera
Computer
Notes
• COMPUTER terminals 1 and 2 function identically.
• For TDP-S81, the document camera should be connected to COMPUTER terminal 2.
• The AUDIO IN terminal doubles for devices connected to COMPUTER terminals 1 and 2.
21
Preparations
Floor-mounted front projection
Operations
Turning the power on and off
■ Connecting the power cord
Notes
1
Insert the power cord connector into the
AC IN socket of the projector.
2
Insert the power cord plug into a wall or
other power outlet.
Power cord connector
(Supplied)
• The start-up screen will disappear after a moment. You can dismiss the start-up screen
before this by performing any operation. You can also configure the start-up screen not to
appear via the Display setting menu p.31 .
• The first time you use the projector after purchase, after the start-up screen disappears,
the Language menu is displayed p.24 .
■ Turning the power off
■ Removing the lens cover
Be sure to remove the lens cover when the power is
turned on. If it is left on, it could become deformed due
to heat.
1
A message appears on the screen, confirming that you wish to shut off the power. This
message will disappear after a moment. (This operation is no longer valid after the
message disappears.)
2
Press the ON/STANDBY button again.
The screen turns off, but the internal cooling fan continues to operate for a short while.
Then, the projector goes into standby mode.
■ Turning the power on
When cooling lamp
The ON indicator will change to
orange, indicating standby mode.
A
(Orange)
2
During internal cooling
After cooling complete
Turn on the main power switch
Press the ON/STANDBY
button.
The power turns on, and the following
3 green indicators light: ON, LAMP,
and FAN. After a moment, the start-up
screen appears.
Control panel
Remote
Control
(Green)
Flashing
(Orange)
(Off)
(Green)
B
(Off)
(Green)
(Orange)
C
(Off)
(Orange)
A
During cooling, the LAMP indicator flashes. In this state, the power cannot be
turned back on.
B
After the LAMP indicator goes off, the cooling fan continues to operate for a
short while, in order to expel excess internal heat. If you are in a hurry, there is
no problem with unplugging the power cord or turning off the main power switch
in this state.
C
In standby mode
Start-up screen
Note
• The projector consumes about 12W of power in standby. We recommend that you unplug
the power cord or turn off the main power switch if you will not be using the projector for
an extended period.
CAUTION
• Do not look into the lens while the lamp is on. The strong light from the lamp may cause
damage to your eyes or sight.
• Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating.
• Do not place your hands, face, or other objects near the air exhaust. Doing so could cause
burns, deform/break the object.
22
PRECAUTION
• If the power cord is unplugged before cooling is complete, give the lamp time (about 5
minutes) to cool before plugging it back in. If the lamp overheats, it may fail to light, and
its lifetime will be shortened.
23
Operations
1
Press the ON/STANDBY button.
Basic operations
5 Projector placement angle adjustments
Turn on the power by following the instructions in “Turning the power on” p.22 .
2 Select the language and the lamp power (When using the
first time).
When the projector is used for the first time after purchase, menu for language and
lamp power selection and configuration is displayed in English. (If the screen is out of
focus, adjust it according to the step 6 .)
q Use the
or
button to select the
desired language and press the
button.
Message for setup confirmation is displayed in a
selected language.
Then, the menu for lamp power selection and
configuration is displayed. It is automatically set as
Standard. To change the setting, follow the step w.
w Using the
or
button, select the lamp
power and press the
button.
English
French
German
Italian
Spanish
Portuguese
Russian
Swedish
Turkish
Japanese
Chinese (simplified)
Chinese (traditional)
Korean
The lamp power, if selected, will be toggled without
pressing the
button. The display automatically
disappears in a few seconds.
Notes
• When the projector is turned on the next time, the Language and Lamp power
menus do not appear upon startup. However, if “Reset all” is executed from the
Default setting menu p.32 , the Language and Lamp power menus will be
displayed the next time when the power is turned on.
• The language can also be set via the Display setting menu p.31 and Lamp power
via the Default setting menu p.32 .
• This owner’s manual assumes that English has been selected.
3 Activate the connected device.
Turn on and start the connected device such as a computer.
4 Press the INPUT button.
An image of the connected equipment is projected.
Each time you press the INPUT button, it switches to the input of the connected
equipment.
Notes
• When [Auto input search] is set to [On] in the default setting menu p.32 , the image of
the equipment which is connected and turned on is projected.
• Moving pictures generated with the DVD software for computers may appear unnatural if
it is projected with this projector, but it is not a malfunction.
24
The placement angle and the height of the projected image can be adjusted by the foot
adjuster.
q Lift up the front of the projector to
the desired angle, then press the
foot adjuster release button.
1
The foot adjuster extends. Release the
button to lock the position.
w To adjust the horizontal angle, use
the tilt adjuster.
To stow the foot adjuster, hold up the projector
while pressing the foot adjuster release button,
then slowly lower the projector.
2
6 Adjusting the screen size and focus
q Use the zooming lever to adjust the screen size.
w Use the focusing lever to adjust the focus.
Readjusting the projection size with the
zooming lever after focusing will cause the
projected image to be out of focus. In that case,
perform focusing again.
7 Adjusting the volume with the
1
2
buttons
The speaker volume can be adjusted when an audio signal is being input.
Notes
• Note that a lamp characteristics may rarely cause the brightness to fluctuate slightly.
• A lamp is consumable item. If used for extended periods, images will appear dark, and
the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The
lifetime of the lamp depends on conditions of use.)
• The DMDTM is made using extremely advanced technology, but there may be black spots
(pixels that do not light) or bright spots (pixels that are constantly lit) on the panel. Please
note that these are not malfunctions.
• Although this projector supports a wide range of RGB signals p.45 , any resolutions not
supported by this projector (SVGA) will be expanded or shrunk, which will affect image
quality slightly. To view high-quality images, it is recommended that the computer’s
external output should be set to SVGA resolution.
• With some models of computer having LCD displays or the like, displaying images
simultaneously on the projector and the monitor’s display may prevent the images from
displaying properly. If this happens, turn off the computer’s LCD display. For information
on how to turn off the LCD display, see the owner’s manual of your computer.
• If a signal not supported by the projector is input, the “Unsupported signal” will appear.
• If no signal is being input from the connected device, the “No signal” will appear.
• If an unavailable operation button is pressed, the
icon will appear.
25
Operations
1 Turn on the power.
Using handy features
■ Using auto setting
● Manual adjustments and settings
Control panel
Remote
Control
1 Press the SET UP button.
The Set up menu appears.
2 Press the SET UP button again.
The menu items of the Set up menu vary depending on the input type, as shown in
the table below.
buttons to adjust the items in the table below, then press
Use the
the RETURN button when you are finished.
Select Item
The displayed menu item is automatically adjusted/set.
icon will appear during
For computer input, the
processing.
For manual adjustment and setting, see the following table p.27 .
● Correcting the keystone distortion
When the foot adjuster p.25 is used to change the projector placement angle while
projecting the image, the picture will undergo keystone (trapezoidal) distortion.
This projector is capable of correcting this keystone distortion.
2 Press the
Yes
Yes
Yes
Keystone
Yes
Yes
Yes
Yes
Auto setting Automatically adjusts items such as the sampling
phase depending on the type of input signal.
Press the SET UP button.
Yes
No
No
No
Phase
Correct the keystone (trapezoid) distortion of the
screen.
Screen shrinking
Screen shrinking
downward
upward
Adjust with
to eliminate flicker.
Yes
No
No
No
Frequency Adjust with
to eliminate periodic patterns
and flickering when many vertical lines appear
on the screen.
Yes
No
No
No
H-position
Adjust the horizontal position of the image.
Move left
Move right
Yes
No
No
No
V-position
Adjust the vertical position of the image.
Move down
Move up
Yes
No
No
No
Clamp 1
Adjusts the clamp pulse position.
Lower
Higher
Yes
No
No
No
Clamp 2
Adjusts the clamp pulse width.
Narrower
Wider
Yes
No
No
No
button.
The keystone distortion is automatically corrected. The
correction.
icon appears during this
● Manual adjustment
Press the SET UP button to display the Set up menu and select [Keystone]. Use
the
buttons for keystone adjustment. When the adjustment is finished, press
the RETURN button. The menu disappears.
Notes
• Depending on the amount of keystone adjustment and the content of images, some
information may be lost, or the picture quality may suffer.
• Keystone adjustment is available for the keystone distortion in a slant angle of ±15
degrees.
• Keystone adjustment will not change the shape of the menus, the start-up screen,
and the background (with no signal input).
26
Video
Camera
S-video
Yes
Before correction After correction
1 Press the SET UP button.
Computer Y/PB/PR
Auto. Keystone Automatically corrects the keystone distortion.
Press
.
Note
• The image may not be projected or auto adjustment/setting may not be performed
correctly for input signals other than those supported by the projector p.45 , p.46 .
Description
27
Operations
This function sets up the projector to the optimum state for
each type of the input signal by using simple operations.
Using handy features (Continued)
Using the menus
■ Cutting off the picture and sound temporarily (Mute)
You can call up on-screen menus, and conduct a number of adjustments and settings using
the operation buttons p.16 on the control panel (main unit side) and remote control.
Remote
Control
The menu shown below is for operation instructions purposes and might differ from the
actual display.
Press the remote control’s MUTE button.
The picture and sound are cut off. (The Mute function is released
when pressing the MUTE button again.)
1. Press the MENU button
2. Select a Category
Notes
Select a category by using
• The
icon will appear while mute is in effect.
• Operating any other functions will also cancel the muting.
■ Freezing the image (Freeze)
The image being projected can be made to be frozen. This function is to
be used to pause a video during a presentation, etc.
■ How to use the menus
Display the Setting display menu
.
Displays the current
adjustments and settings of
selected category.
Item shown with gray cannot
be adjusted with the current
input source.
There are following four
categories:
Remote
Control
Image adjustment menu p.30
Display setting menu
p.31
Press the remote control’s FREEZE button.
Default setting menu
p.32
The picture pauses. (The Freeze function is released when pressing
the FREEZE button again.)
Status display menu
p.33
3. Adjustments & Settings
Notes
Press
to open the menu.
Item
Adjustment/Setting Value
• The
icon will appear while freeze is in effect.
• Other operation will also release the freeze.
• Even if an image is frozen on the projector, the pictures are running on the video or
other equipment.
• If you use this function on video software sold on the market, broadcast or
broadcast on cable except for the purpose of your private viewing and listening, it
may infringe the copyright protected by the copyright laws.
These marks signify the
items can be adjusted/set
by using
.
5. End
Press the MENU
button
The menu disappears.
This mark signfy that
there are options.
Press
to display a
list of options.
These marks signify the items can
be selected from the list by using
.
After an item is selected, apply it
by pressing
.
The figure shows displays given for operation instructions purposes. As the display
may differ depending on the item, use the following pages as a reference.
Note
4. Back
Return button
• Menu adjustments and settings are saved when the power is turned off via the ON/
STANDBY button. If the power cable is disconnected before this, or the power goes out,
then the data will not be saved.
28
29
Operations
When you want to project the images of another projector, overhead
projector, etc. temporarily, this projector’s images and sound can be
turned off.
Using the menu (Continued)
■ The image adjustment menu
■ The display setting menu
Use this menu to adjust image-related items.
Items that can be adjusted are marked with “Yes”, and those that cannot are marked with “No”.
Use this menu to set screen display-related items.
Contrast
Description
Computer Y/PB/PR
Adjust the image contrast.
Higher
Lower
Video
Camera
S-video
Yes
Yes
Yes
Yes
Brightness Adjust the brightness of the image.
Darker
Brighter
Yes
Yes
Yes
Yes
Color
Adjust the color of the image.
Lighter
Deeper
No
Yes
Yes
No
Tint *1
Adjust the tint of the image color.
Greenish
Reddish
No
No
Yes
No
Sharpness Adjust the sharpness of the image.
Sharper
Softer
No
Yes
Yes
Yes
Noise
reduction
Set the function to reduce screen noise.
On (Enable)
Off (Disable)
No
Yes
Yes
No
Picture
mode
Press . Toggle the picture mode with
/ .
Bright/Standard/True color
Yes
Yes
Yes
No
R-level
Adjust red of the image color.
More red
Less red
Yes
Yes
Yes
Yes
G-level
Adjust green of the image color.
Less green
More green
Yes
Yes
Yes
Yes
B-level
Adjust blue of the image color.
More blue
Less blue
Yes
Yes
Yes
Yes
NTSC mode*1
Set the black level with
/
button.
US:
NTSC (US) mode
Japan: NTSC (JAPAN) mode
No
No
Yes
No
Shutter
No
No
No
Yes
(TDP-S81)
Set the shutter speed of the camera to
the local power frequency.
60 Hz
50 Hz
White
balance*2
(TDP-S81)
Set the white balance of the document
camera.
Lock
Auto
No
No
No
Yes
Item
Description
Screen size
(Full): Display with 800 × 600 dot resolution
(Thru): Display with sampling resolution (for computer input)
(Wide): Wide-screen display (for Video, S-video, and Y/PB/PR)
Language
Select one of the languages below to use for displaying the menu and messages
[ : Enter setting mode] [
:Selection]
[Apply:
]
English/Français/Deutsch/Italiano/Español/Português/
/
Svenska/Türkçe/
/
/
/
Background
Screen to display when there is no input signal
Icon
Display icons as function guides
(Blue)
(Black)
On
Off
Start-up screen Display start-up screen when power is turned on On
Off
Note
• If “Thru” is selected for screen size, portions exceeding the native resolution (800 × 600
pixels) will not appear on the screen. Note that for RGB signals with clock frequency
110MHz or lower, all input pixel signals are sampled. However, if the clock speed is
higher than this, the RGB pixel signal is thinned before sampling.
*1: [Tint] and [NTSC mode] can be displayed and adjusted only when the video signal is set to
[NTSC] and [NTSC4.43]. (NTSC mode is set to JAPAN when the language is set to Japanese. It is
set to US for other languages.)
*2: Even if the white balance is set to [Lock], turning the projector off disables this function and
turning it on again the next time resets the menu to [Auto]. (TDP-S81)
30
(Logo)
31
Operations
Item
Using the menu (Continued)
■ Displaying Information (Status display)
■ The default setting menu
This menu shows placement status and other settings.
This displays information about the input signal, lamp use time, etc.
Description
“Yes”: displayed, “No”: not displayed
Projection
mode
Sets projection mode in accordance with Placement Style.
No signal
power off
Set the timer to wait for the power to be turned off after signal input stops.
Press
. Switch with
and
.
Off (not turned off)/1 min./5 min./10 min./30 min./60 min.
Auto input
search
Set whether the input with signals is only selected or not.
Power on
Sets whether to turn on the power when the ON/STANDBY button is pressed
(Manual), or when the power cord is plugged in (Auto). Manual
Auto
(Standard)
(Rear)
(Mounted
from ceiling)
(Rear mounted
from ceiling)
On
Lamp power [Note 1] Sets the lamp power.
Low
Fan mode [Note 2] Sets the cooling fan speed.
Standard
Reset all
p.20
Press
.
Resets all adjustments and settings to their factory settings. Yes
Off
Standard
High
No
Notes
1: When Lamp power is set to Low, the screen becomes a little darker, but the cooling fan noise gets
quieter. This setting will be cleared when you turn the power off.
2: Setting [Fan mode] to [High] increases the cooling fan speed. Set this option to use the projector,
for example, at high altitude (over 1,500 meters above sea level).
Notes
• Note that in the event of a power outage but the power is restored afterwards, the projector
power will come on if Power on is set to Auto, and the power cord is plugged in.
• When you turn off the projector even if Power on is set to Auto, you must press the ON/
STANDBY button to turn the power off.
Item
Input
Mode name
H-resolution
V-resolution
H-frequency
V-frequency
Sync
Signal format
Video mode
Lamp time
Lamp reset count
Total time
Version
Description
Input source name
RGB input mode [Note 1]
Horizontal resolution (in dots)
Vertical resolution (in dots)
Horizontal sync frequency
Vertical sync frequency [Note 2]
Sync signal polarity [Note 3]
Y/PB/PR signal format
Color method of video signal
Time of lamp use [Note 4]
The count for lamp replacement
The total time that this projector is used
Firmware version [Note 5]
Computer Y/PB/PR
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
Yes
No
Yes
Yes
Yes
Yes
Video
Camera
S-video
Yes
Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Notes
1: The mode of supported RGB signals p.45 is shown.
2: Same as the refresh rate of the computer signal.
3: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
4: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as
a counter of guaranteed lamp time.) When the displayed time approaches 2,000 hours, consult
with a store about getting a TLPLW5 replacement lamp (sold separately) prepared.
5: [Version] shows the version of the projector’s internal control program. This version is referred
to for customer service, etc.
Note
• The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
32
33
Operations
Item
Using the document camera
Please read this chapter if the model you purchased is TDP-S81 which includes a document camera.
■ How to use the document camera
Status before preparation
(When stored)
Using the camera attached on the projector
Status before preparation
(When stored)
1) Set up arm.
Using the camera removed from the projector
2) Rotate arm.
1) Disconnect the RGB
cable, then slide the
lock switch to release
lock.
2) While pushing the lock
lever in the arrow
direction, lift up the
document camera.
②
①
3) Remove the document
camera from the tray.
Pull up toward direction q
3) Raise camera head.
4) Extend the tip resistant
bars to set the
document camera.
5) Connect the document
camera and the
projector using the
supplied RGB cable.
Operations
①
PRECAUTIONS
PRECAUTIONS
• For camera interconnection, be sure to use the supplied RGB cable (25 cm or 3 m). If you
use the other cables, the normal operation may not be achieved and even the malfunction
may result.
• When moving the projector with the camera attached, do not grab the camera arm and/or
the camera head.
• When moving the projector with the camera attached, first ensure that the camera is securely
locked in position on the tray.
• Insert the RGB cable straight and securely until it is fixed in place.
• Do not jolt or force the camera head or camera arm. Doing so could cause malfunction.
• Note that when extending or rotating the camera arm, the arm moves in an arc. Take care
not to bump yourself or others with it.
• When placing the projector in the carrying bag, remove the connection cables. Otherwise,
damage to the connectors and cables may result.
• Installation of the document camera onto the tray should be performed in the reverse
order shown above.
• When replacing the document camera on the tray, ensure that the lock lever is securely
locked in position.
• When using the tip resistant bars, pull them fully until each forms the angle of 90 degree.
If you don’t use the bars, the camera may topple over.
34
35
Using the document camera (Continued)
■ Image projection with the document camera
1 Place the document.
6 If the screen is too dark or too bright, use the CAMERA GAIN (+/–)
buttons to make it easier to see.
The Sharpness of the camera image can also be adjusted using
the Image adjustment menu p.30 .
Set the document at the side of the projector.
7 After use, fold up the document camera.
Fold up the camera using the reverse order from unfolding the document camera p.34 .
Notes
• The input returns to the previous input when the CAMERA button
is pressed again.
• Camera input can also be selected by pressing either the remote control or projector’s
INPUT button.
3 Rotate the camera head to align the orientation of the document for
shooting by checking the screen.
■ Locking the white balance
Although the projector’s camera is constantly adjusting the color balance of the images
it photographs, the color balance may be disrupted, depending on the color layout of
the document. If this happens, the white balance can be locked using the procedures
below.
1 Lay down a piece of white paper, and adjust so it fills the screen.
Adjust the camera head and arm so that the white
paper fills the screen completely.
4 Move the camera arm up and down to adjust the image size.
Farther (↑): Smaller image
Closer (↓): Larger image
2 Set the White balance to Lock in the Image adjustment menu.
p.30
The white balance is locked. If you want to return to the auto adjustment, set the White
balance to Auto in the Image adjustment menu.
Notes
• Closeup shot with the distance shorter than 100 mm cannot be performed.
5 Adjust the focus using the focusing lever on the camera head
Focusing lever
Rotate the focusing lever to either NEAR or
FAR, whichever is better in focusing.
• Near : 100 mm to 300 mm
Far : 300 mm to 5 m
36
• If the white balance is set to Lock, once power is turned off, the setting goes back to
Auto.
• The color of the room lighting may prevent the white balance from being adjusted to the
optimum level. In this situation, or if you want to use a certain tinting, adjust the R-level,
G-level and B-level on the Image adjustment menu p.30 .
37
Operations
2 Press the CAMERA button, and select camera input.
• There is no audio output when camera input is selected.
• If the room’s fluorescent lighting causes the image to flicker, either turn off the fluorescent
light, or set the Shutter from the Image adjustment menu p.30 . Note that changing the
Shutter setting may not eliminate the flicker, depending on the lighting, state of the
document, or image adjustment.
Maintenance
About lamp
The product’s light source is a mercury lamp that lights at increased internal pressure. Be sure
to fully understand the following characteristics of the lamp and handle it with extreme care.
• The lamp may explode with a loud noise due to impact or deterioration, or fail to light at
the expiration of its life.
• How long it takes before the lamp explodes or the life expires may vary greatly by lamp.
Some may explode shortly after first use. (Free replacement is available if the lamp
explodes within the warranty period. Contact the dealer from whom you purchased the
product in such a case.)
• Explosion is likely to happen if the lamp is used after the replacement period has elapsed.
• When the lamp explodes, the broken pieces of glass may get inside the product or be
released outside from the openings for ventilation.
• When the lamp explodes, a slight amount of mercury gas enclosed in the lamp along
with glass dust may be released from the openings for ventilation.
■ Immediately replace the lamp when a sign appears on the screen.
• When the replacement time approaches, a message will appear on the screen.
• The risk of explosion will increase if the lamp is continuously used without being replaced.
• Frequently check the used hours and prepare spares when the replacement time
approaches. (Refer to “Status display”. p.33 )
■ When the lamp is broken
1 Unplug power cord.
2 Wait until lamp is sufficiently cooled.
Wait for at least 1 hour.
3
3 Remove the lamp cover.
Loosen the 1 screw, then pull up to the direction of the arrow with your fingers as shown to
remove the lamp cover. Use care to avoid any
damage to nails and/or tip of your finger(s). If
you have any difficulty in removal, you can use
a screwdriver or any other smaller tool for your
convenience.
Lamp cover
1
2
4 Pull out the lamp.
Loosen the 2 screws holding the lamp in place,
and pull up the handle to remove the lamp.
1
4
2
5 Mount the new lamp.
Lamp replacement
A lamp is consumable supplies. If used for extended periods, images will appear dark, and
the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The lifetime
of the lamp depends on condition of use.) If this happens, replace it with a new one.
Align the orientation, press down until the bottom is
reached, and lock in place using the two lamp
locking screws.
6 Replace the lamp cover.
2
5
Align the cover, and press it in, then tighten the
screws loosened in step 3 until the lamp cover is
no longer loose.
1
7 Reset the lamp timer.
See the lamp’s manual for instructions on resetting
the lamp timer.
Notes and Precautions
WARNING
• If you have been using the projector, the lamp will be very hot, and may cause burn injuries.
Wait for the lamp to cool (for longer than 1 hour) before replacing it.
• If the lamp should break, please handle with care to avoid injury due to broken pieces and
contact your dealer for repair service.
• Press the
button twice to display (a rough guide) the time of lamp use, the Lamp time
item, in the Status display menu. p.33
• It is recommended that the lamp be replaced after 2,000 hours of use. When Lamp time
reaches 2,000 hours, the
icon and a message will appear. This display disappears
button.
when you press
• Attach the lamp cover correctly so that it is not loose. If it is not attached correctly, the
lamp may fail to come on p.41 , and the lamp’s lifetime may be shortened.
• Always replace the lamp with a new one.
• The lamp is made out of glass. Do not touch the glass surface with your bare hands,
bang it, or scratch it. (Dirt, jolts, scratches and the like could break the lamp.)
38
39
• If the projector is mounted on a ceiling, request a lamp replacement from your projector dealership.
• When replacing, always use lamp “TLPLW5” (sold separately).
CAUTION
Maintenance
• If glass components, including a lamp and a lens, should break, handle the broken
pieces with care to avoid injury and contact your dealer for repair service.
• In the event of lamp explosion, unplug the product from the wall outlet, leave and
completely ventilate the room. Then, thoroughly clean the area around the projector and
discard any edible items placed in that area.
• When the lamp explodes, consult a doctor if glass dust or mercury gas gets into your
eyes or you breathe it.
Others
Lamp replacement (Continued)
Used Lamps
Trouble indications
The indicator lights inform you of internal abnormalities.
This projector’s lamps contain trace amounts of environmentally harmful inorganic
mercury. Be careful not to break used lamps, and dispose of them in accordance with
local regulations.
No power
⇒ Problem with projector
• Unplug the power cord, and contact your dealer.
⇒ The lamp cover is not properly attached.
• Unplug the power cord, and reattach the lamp cover.
(Off)
Lens and main unit cleaning
Lamp went out during use, or won’t come on
⇒ Lamp temperature is high so that it is difficult to turn on, the lifetime of
the lamp has ended or the projector is malfunctioning.
• Unplug the power cord and wait for a short while, then turn the power back on.
• If a lamp burns out, replace it with a new one.
❈ After approx. one minute of abnormal display, the projector returns to
the standby state waiting for internal cool down.
(Red lit)
WARNING
• Request cleaning and maintenance of a ceiling-mounted unit from your projector dealership.
Attempting to clean/replace the lamp at a high site by yourself may cause you to drop
down, thus resulting in injury.
(Red lit)
Power went out during use
(Red lit or flashing)
■ Lens cleaning
(Green lit)
Or (Orange lit)
• Clean the lens with a commercially available blower and/or
lens cleaner.
• The lens is easily scratched, so do not rub it with hard objects,
or strike it.
(Red lit)
(Red lit or flashing)
Or (Orange lit)
(Red lit)
⇒ Problem with internal cooling fan.
• Unplug the power cord, and contact your dealer.
❈ The
icon will appear before the power goes out.
❈ After approx. one minute of abnormal display, the projector returns to
the standby state waiting for internal cool down.
Power went out during use
(Green lit
or Off)
(Green lit
or Off)
(Green
flashing)
● Replacing cooling fans
To maintain the performance, it is recommended that cooling fans should be replaced
about every 2 to 3 years. Consult with your dealer for details.
⇒ Internal overheating, or the outside temperature is too high.
• Place the projector so that the air intake and exhaust are not blocked.
• Unplug the power cord and wait for a short while, then turn the power back on.
❈ The
icon will appear before the power goes out.
❈ After approx. one minute of abnormal display, the projector returns to
the standby state waiting for internal cool down.
Power went out during use
■ Main unit cleaning
• Clean the main unit after unplugging the power cord.
• Wipe dirt off the main unit gently with a soft cloth.
• If the soiling is severe, dip the cloth in a neutral
detergent diluted in water, wring well, and gently wipe
off the dirt, then finish up by wiping with a dry cloth.
p.39
(Red lit)
⇒ Problem inside the projector.
• Unplug the power cord and wait for a short while, then turn the power back on.
• If the above action will not clear the problem, unplug the power cord,
and contact your dealer.
❈ After approx. one minute of abnormal display, the projector returns to
the standby state waiting for internal cool down.
Power went out during use
TDP-S81
(Green lit)
⇒ Camera is not correctly connected.
• Disconnect the power plug and check the connection with the camera.
❈ The
icon will appear before the power goes out.
❈ After approx. one minute of abnormal display, the projector returns to
the standby state waiting for internal cool down.
PRECAUTION
• Make sure to unplug the power cord if something goes wrong.
40
41
Others
(Red lit)
Before calling service personnel
If you think something is wrong, check the followings before contacting customer service.
Please see “Trouble indications” p.41 as well.
If This Happens
Check
No power
• Is the power cord plugged in? Is it connected to the projector?
• Is the lamp cover loose? p.39
Power goes out
during use
• Is the ambient temperature high? p.41
• Is the air intake or air exhaust blocked?
No picture
•
•
•
•
•
Is the projector turned on? p.24
Is the mute function on? p.28
Is the brightness setting minimized? p.30
Are the connections set up correctly? p.21
Are all the connected devices functioning properly?
No audio
•
•
•
•
•
Is the projector turned on? p.24
Is the mute function on? p.28
Is the volume setting minimized? p.25
Are the connections set up correctly? p.21
Are all the connected devices functioning properly?
Picture not
displayed
correctly
• Is the input signal supported by the projector? p.45 , p.46
• Is there something generating an abnormal video signal, for
instance the video tape?
Picture blurred
Part of picture
out of focus
• Is the lens dirty? p.40
• Is the lens focus adjusted optimally? p.25
• Is the projection distance within the projector’s supported range?
p.41
If This Happens
Check
TDP-S81
The images from the
document camera
are blurry
• Is the document imaging camera’s lens dirty?
• Is the document imaging camera out of focus? p.36
• Is the location of the object being focused too dark?
TDP-S81
The images from the
document camera
are flickering
• Is there impact from the room’s fluorescent lighting?
Turn off the fluorescent lights, or change the shutter speed settings.
p.30
p.20
• Is the projector’s screen placement angle tilted too far? p.20
• Are the sharpness or sampling phase adjustments off? p.27 p.30
Image is dark
• Are the brightness or contrast adjustments off? p.30
• Is the lamp nearing the end of its service life? p.33
Colors too light
Bad shading
• Are the color, tint, R-level, G-level, or B-level adjustments off? p.30
• Is the screen dirty?
• Is the lamp nearing the end of its service life? p.33
Remote control
doesn’t work
•
•
•
•
42
Others
Are the remote control’s batteries drained?
Are the batteries inserted into the remote control correctly? p.19
Is the remote control being used within the effective range? p.19
Are there any obstructions between the remote control and
projector?
• Are there any fluorescent or other bright lights shining at the
projector’s infrared remote sensor?
43
Specifications
■ List of general specifications
Item
■ List of supported signals (RGB signals)
Specification
270 W
TDP-S80: 2.8 kg
Weight
TDP-S81: 3.7 kg
External Dimensions
TDP-S80: 298 × 101.4 × 275.4 mm (W × H × D)
(including protruding parts)
TDP-S81: 383 × 101.4 × 275.4 mm (W × H × D)
Cabinet material*
PC+ABS resin and ABS resin
Conditions for usage environment Temp: 5°C to 35°C; relative humidity: 30% to 70%
Display pixels
1 chip DMD™
Picture elements
480,000 pixels (800H × 600V)
Lens
Zoom lens
F=2.6-2.81 f=22.34-26.8 mm
Lamp
High-pressure mercury lamp
Projection screen size
24.6-246 inches
Projection distance
1.20-10.00m
Speaker
1 W (Monaural)
COMPUTER-1 terminal Mini D sub 15 pin RGB / Y/PB/PR (dual use)
COMPUTER-2 terminal Mini D sub 15 pin RGB / Y/PB/PR (dual use) / CAMERA (TDP-S81)
MONITOR terminal
Mini D sub 15 pin RGB / Y/PB/PR (dual use)
S-VIDEO terminal
Mini DIN 4 pin
AUDIO (L/R) terminal
RCA Pin Jack × 2, 1.5 V (rms), 22 kΩ or more
VIDEO terminal
RCA Pin Jack, 1 V (p-p), 75 Ω
AUDIO IN terminal
ø3.5mm dia. stereo mini-jack, 1.5V (rms); 22 kΩ or more
AUDIO OUT terminal
ø3.5mm dia. stereo mini-jack
CONTROL terminal
Mini DIN 8 pin (RS-232C)
Connection terminal
Consumption Power
■ Document camera specifications (TDP-S81)
Item
Lens
Focusing
Zooming
Image element
Effective pixels for pickup section
This projector supports the following RGB signals. Note, however, that depending on the
computer model, the screen may show flicker or streaking. Please adjust the projector if
this happens.
(Press the SET UP button, and adjust automatically or manually. p.26 , p.27 )
Resolution
Mode
720 x 400
640 x 480
720x400_85
VGA_60
VGA_72
VGA_75
VGA_85
SVGA_56
SVGA_60
SVGA_72
SVGA_75
SVGA_85
MAC16"
XGA_60
XGA_70
XGA_75
XGA_85
MAC19"
SXGA1_75
QuadVGA_60
QuadVGA_85
SXGA3_60
SXGA3_75
SXGA3_85
SXGA+
UXGA_60
UXGA_65
UXGA_70
UXGA_75
UXGA_85
800 x 600
832 x 624
1024 x 768
1152 x 864
1280 x 960
1280 x 1024
Specification
F=2.8, f=2.8mm
Switching in two steps
None (adjusted through distance from subject)
1/4.2 inches honeycomb CCD
629,856 pixels (648H × 486V × 2)
1400 x 1050
1600 x 1200
* Each plastic part displays the materials it is made from, in order to facilitate recycling after this
product becomes no longer usable.
Refresh rate
(Hz)
85.039
59.940
72.809
75.000
85.008
56.250
60.317
72.188
75.000
85.061
74.550
60.004
70.069
75.029
84.997
74.700
75.000
60.000
85.002
60.020
75.025
85.024
60.012
60.000
65.000
70.000
75.000
85.000
H-frequency
(kHz)
37.927
31.469
37.861
37.500
43.269
35.156
37.879
48.077
46.875
53.674
49.725
48.363
56.476
60.023
68.667
60.134
67.500
60.000
85.938
63.981
79.976
91.146
63.973
75.000
81.250
87.500
93.750
106.250
Clock
(MHz)
35.500
25.175
31.500
31.500
36.000
36.000
40.000
50.000
49.500
56.250
57.283
65.000
75.000
78.750
94.500
79.857
108.000
108.000
148.500
108.000
135.000
157.500
118.094
162.000
175.500
189.000
202.500
229.500
• Design, specifications, etc. subject to change without notice for improvements, etc.
44
• Signals which resolution exceeds the native resolution (800 × 600 pixels) will be
compressed. For this reason, some information may be lost, or image quality may be
affected.
45
Others
Note
Note
Specifications (Continued)
■ CONTROL terminal
Signal format
480i(525i)@60Hz
480p(525p)@60Hz
576i(625i)@50Hz
576p(625p)@50Hz
720p(750p)@60Hz
fh(kHz)
15.73
31.47
15.63
31.25
45.00
fv(Hz)
59.94
59.94
50.00
50.00
60.00
720p(750p)@50Hz
1080i(1125i)@60Hz
1080i(1125i)@50Hz
1035i(1125i)@60Hz
1152i(1250i)@50Hz
37.50
33.75
28.13
33.75
31.25
50.00
60.00
50.00
60.00
50.00
■ List of supported signals (Video, S-Video signals)
Video mode
fh(kHz)
fv(Hz)
fsc(MHz)
NTSC
PAL
SECAM
PAL-M
PAL-N
PAL-60
NTSC4.43
15.73
15.63
15.63
15.73
15.63
15.73
15.73
60
50
50
60
50
60
60
3.58
4.43
4.25 or 4.41
3.58
3.58
4.43
4.43
■ Pin assignment of COMPUTER-1/2 & MONITOR terminals
5
10
15
1
6
11
Mini D sub 15 Pin connector
Input Signal
• RGB input
RGB signals:
Horizontal sync signal:
Vertical sync signal:
• Y/PB/PR input
Y signal:
PB/PR signals:
0.7V (p-p) 75 Ω
TTL level (Pos/neg polarity)
TTL level (Pos/neg polarity)
1.0V (p-p) 75 Ω
0.7V (p-p) 75 Ω
Pin
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Pin description
During RGB input
During Y/PB/PR input
Video signal (R)
Color difference signal (PR)
Video signal (G)
Luminance signal (Y)
Video signal (B)
Color difference signal (PB)
GND
∗
GND
∗
GND (R)
GND (PR)
GND (G)
GND (Y)
GND (B)
GND (PB)
N.C
∗
GND
∗
GND
∗
N.C
∗
Horizontal sync signal ∗
Vertical sync signal
∗
N.C
∗
● Pin assignment
7
6
8
5
3
4
2
1
Pin No.
1
2
3
4
5
6
7
8
Signal Name
RXD
CTS
DSR
GND
RTS
N.C
TXD
GND
Mini DIN 8 pin connector
● Interface format
1 Communication method
2 Communication format
3 Data format
4 Replies
RS-232C, 9600bps, No Parity, Data Length: 8 bits;
Stop Bit Length:
1 bit
STX (02h) Command (3Byte) ETX (03h)
Only 1 command valid per communication.
For input commands, only ASCII-compliant all-uppercase
alphanumeric characters supported.
Acknowledge
No acknowledge
ACK (06h) CR (0Dh) Data
... Normally ended
ACK (06h) ESC (1Bh)
... Aborted
NAK (15h)
If commands are to be sent consecutively, wait for the response from the projector
before sending the next command.
● Main Commands
Item
Power on
Power off
Icon display on
Icon display off
Auto setting (RGB input)
Status display on
Status display off
Command
PON
POF
MO0
MO1
PAT
DON
DOF
Item
Computer (1) input select
Computer (2) input select
Video input select
S-video input select
Camera input select (TDP-S81)
Command
IN1
IN2
IN3
IN4
IN5
Note
• Contact your dealer for control cable and other commands.
■ Separately sold product
Replacement Lamp
Model TLPLW5
∗ Do not connect anything.
46
Description
Receiving data
Consent to send
Data set ready
Signal ground
Request to send
No connection
Sending data
Signal ground
Others
■ List of supported signals (Y/PB/PR signals)
47
Download PDF
Similar pages