1
Industrial PoE Managed Switches
IPGS-3408GSFP
8 10/100/1000T + 4 1000M SFP L2+ 8 PoE at/af Industrial Managed Switch
w/ Enhanced G.8032 Ring & PTP

Support IEEE802.3at/af up to 30W per port

PoE management incl. Detection and Scheduling

Enhanced G.8032 ring protection < 20ms with auto mode,
enhanced mode, train mode and basic mode; Enhanced
G.8032 ring covers multicast packets; MSTP 16MSTI /RSTP

Miss-wiring avoidance & Repowered auto ring restore (node
failure protection)

User friendly UI, including auto topology drawing and DDM
threshold monitoring with dB values***; Complete CLI

Support LACP link aggregation, IGMP v3/router port, DHCP server & DHCP Option82
for Port&VLAN based DHCP distribution, Mac based DHCP server, QoS by VLAN,
SSH/SSL, HTTPS, ACL, IPv6, SMS

Environmental Monitoring for temp., voltage & current**
OVERVIEW
Lantech IPGS-3408GSFP is a high performance L2+ (Gigabit
routine time table. Each PoE ports can be Enabled/disabled, get
uplink) switch with 8 10/100/1000T + 4 1000M SFP w/8 PoE
the voltage, current, Watt, and temperature info displayed on
802.3af/at Injectors which provides L2 wire speed and
WebUI.
advanced security function for network aggregation deployment.
It delivers ITU G.8032 enhanced ring recovery less than 20ms
The IPGS-3408GSFP also embedded several features for
including dynamic coupling ring, enhanced mode for easy
stronger and reliable network protection in an easy and intuitive
configuration and aggregation ring*, comprehensive QoS, QoS
way. When the pre-set ring configuration failed or looped by
by VLAN, advanced security including ACL L2/L3, SSH/SSL,
miss-wiring, Lantech IPGS-3408GSFP is able to alert with the
Mac based DHCP server, DHCP Option 82, DHCP server,
LED indicator and send out an email, traps or a SMS text.
IGMPv1/v2/v3/router port, QinQ* (double tag VLAN) which are
Repowered auto ring restore function (node failure protection)
important features required in train and large network. It also
ensures the switches in a ring to survive after power breakout is
supports Cisco Discovery Protocol (CDP) and LLDP for
back. The status can be shown in NMS when each switch is
Ciscoworks to detect the switch info and show on L2 map
back. This feature prevents the broken ring and keep ring alive
topology.
without any re-configuration needed. Loop protection is also
available to prevent the generation of broadcast storm when a
Lantech IPGS-3408GSFP features hardware-based PTP
dumb switch is inserted in a closed loop connection.
IEEE1588 v2 two-step function which can allow 8 10/100/1000T
uplinks to synchronize the network with precise accuracy (under
DHCP option 82 and relay agent function (port&vlan based
1μs). It has RTC (Real Time Clock) inside that can keep track of
DHCP distribution) can offer the same IP address on port base
current time.
or vlan base where there is need to replace the new device
connecting to Lantech switches to avoid any network disruption.
Compliant with 802.3af/at standard, the Lantech
The built-in DHCP Option 82 server offers the convenience of
IPGS-3408GSFP is able to feed each PoE port up to 30
policy setting on the switch. Mac based DHCP server function
Watts@54 VDC providing the connected PD devices. Lantech
assigns an IP address according to its MAC address to include
IPGS-3408GSFP supports advanced PoE management
dumb switches in DHCP network.
including PoE detection and scheduling. PoE detection can
detect if the connected PD is hang up then restart the PD; PoE
The user friendly UI, innovative auto topology drawing and
scheduling is to allow pre-set power feeding schedule upon
topology demo makes IPGS-3408GSFP much easier to get
Datasheet Version 2.0
www.lantechcom.tw | info@lantechcom.tw
2
Industrial PoE Managed Switches
hands-on. The switch also equips the RTC (real time clock)
Port / Power events, for example, DIDO function can trigger
which can keep track of time always. The IPGS-3408GSFP
alarm if the switch was moved or stolen. In case of events, the
supports DMI interface that can correspond with DDM SFPs
IPGS-3408GSFP will immediately send an email & SMS text
(Digital diagnostic monitor) to display the five parameters in
message to pre-defined addresses as well as SNMP Traps out.
Lantech’s UI, including optical output power, input power,
It provides 2DI and 2DO while disconnection of the specific port
temperature, laser bias current and transceiver supply
was detected; DO will activate the signal LED to alarm. DI can
voltage***. The TX power/RX power raw data is automatically
integrate the sensors for events and DO will trigger the alarm
converted to dB values for installer, making it easier to calculate
while sending alert information to IP network with email and
the fiber distance. The complete CLI enables professional
traps.
engineer to configure setting by command line.
The optional environmental monitoring can detect switch overall
Lantech IPGS-3408GSFP features enhanced G.8032 ring
temperature, voltage and current where can send the SNMP
which can be self-healed in less than 20ms for single ring
traps, email and SMS alert when abnormal.
topology protection covering Multicast packets. It also supports
various ring topologies that covers double ring, multi-chain
The Lantech IPGS-3408GSFP is designed with dual power
(under enhanced ring), train ring, basic ring by easy setup than
supply at 48VDC. The 12V model is built with Booster
others. The innovative auto-Ring configurator (auto mode) can
technology that can accept input voltage from 12V ~ 48V and
calculate owner and neighbor in one step. It supports MSTP
deliver PoE power at 48V to feed the PD. Featured with relay
that allows RSTP over Vlan for redundant links with 16 MSTI.
contact alarm function, the IPGS-3408GSFP is able to connect
The ITU G.8032 Ring and RSTP can be co-existed in the same
with alarm system in case of power failure. The
switch with different ports for the most flexible protection.
IPGS-3408GSFP also provides ±4000V EFT and ±6000V ESD
protection, which can reduce unstable situation caused by
The configuration file of Lantech IPGS-3408GSFP can be
power line and Ethernet.
exported in text file so that it can be edited and configured back
to switch with ease for mass deployment. The factory reset
Lantech IPGS-3408GSFP features high reliability and
button can restore the setting back to factory default and built-in
robustness coping with extensive EMI/RFI phenomenon,
watchdog design can automatically reboot the switch when
environmental vibration and shocks usually found in factory,
CPU is found dead.
substation, steel automation, aviation, mining and process
control. It is the best solution for Automation, transportation,
QoS by VLAN can allow switch to tag QoS by VLAN regardless
surveillance, Wireless backhaul, Semi-conductor factory and
the devices acknowledge QoS or not in which greatly enhance
assembly lines.
the bandwidth management in a network.
The -E model can be used in extreme environments with an
The IPGS-3408GSFP DIDO function can support additional
operating temperature range of -40°C to 75°C.
open/close physical contact for designate applications besides
FEATURES & BENEFITS


8 10/100/1000T + 4 1000M SFP w/8 PoE 802.3af/at
Injectors (Total 12 Ports Switch)

Embedded 8 PoE Injectors IEEE802.3af/at function
to feed power up to 30W@54V; 15W @ 48V per port
for active operation

PoE voltage boost from 12V to 48V (12V model)

PoE management including PoE detection and
scheduling for PD (power devices)

IEEE 1588 PTP v2 two-step (under 1μs)

Back-plane (Switching Fabric): 24Gbps

16K MAC address table

DDM to support SFP diagnostic function***


Provides EFT protection ±4000 VDC for power line.

Supports ±6000 VDC Ethernet ESD protection

LACP load balancing to distribute the load*

Built-in RTC (Real Time Clock) to keep track of time

Supports IEEE 802.1p Class of Service, per port
provides 8 priority queues Port base, Tag Base and
Automatically convert the raw data into dB
values for TX power/RX power, making it easier
to measure the fiber distance

9KB Jumbo frame supported on all ports

User friendly UI, auto topology drawing, topology
demo, complete CLI for professional setting


Enhanced G.8032 Ring protection in 20ms < 256
switches
Support various ring/chain topologies, including
dynamic coupling ring& aggregation ring*

Enhanced G.8032 ring configuration with ease

Auto ring configuration(auto mode) for single
ring

Co-exist with RSTP on different ports
Aggregation ring for ring redundancy and
bandwidth combination*
Type of Service Priority

IEEE 802.1d STP, IEEE 802.1w RSTP,802.1s MSTP
VLAN redundancy

4K 802.1Q VLAN, Port based VLAN, GVRP**, QinQ*

Supports IEEE 802.1ab LLDP, Cisco CDP; LLDP info
can be viewed via Web/ Console/ LantechTM
InstaConfig**/ LantechTM InstaView**
Datasheet Version 2.0
www.lantechcom.tw | info@lantechcom.tw
3
Industrial PoE Managed Switches



DHCP server / client / DHCP Option 82 relay / DHCP
Option 82 server for Port&Vlan based DHCP
distribution
Mac based DHCP server to assign IP address that
includes dumb switches in DHCP network

Ingress packet filter and egress rate limit
Relay alarm output system events

Miss-wiring avoidance

LED indicator

Email, traps, or SMS notification
Repowered auto ring restore

Ensure the switches in a ring to survive after
power breakout is back

TFTP/HTTP firmware upgrade; LantechTM
InstaConfig** for multiple upgrade

counters

Security

SSL/SSH/ACL L2&L3

Port Security: MAC address
Management access control with priority

Login Security: IEEE802.1X/RADIUS

HTTPS for secure access to the web interface
Static multicast forwarding forward reversed IGMP
ports for IP surveillance application

Multicast static route for non- IGMP camera to
prevent flooding; IGMP router port to assign query
in ring and for reversed multicast video flow

Multicast VLAN registration* for metro video

IGMPv1,v2,v3 with Query mode for multi media

Factory reset button to restore setting to factory
default

Watchdog design to auto reboot switch CPU is
found dead

System Event Log, SMTP Email alert, SMS mobile
(text) and SNMP Trap for alarm support; 32 RMON

flow (MVR) with multicast packets binding with
The status can be shown in NMS when each
switch is back


Broadcast/multicast packet filter control

IP Security: IP address security management to
prevent unauthorized intruder.
Bandwidth Control


entries/Filter/MAC-Port binding

Optional environmental monitoring for system input
voltage, current, ambient temperature

Supports DIDO (Digital Input/Digital Output)

IP30 metal housing with DIN rail and Wall-mount**
design
DIMENSIONS (unit=mm)
Standard model
Datasheet Version 2.0
www.lantechcom.tw | info@lantechcom.tw
4
Industrial PoE Managed Switches
12V model
SPECIFICATION
Hardware Specification
Standards
Switch Architecture
Transfer Rate
CPU
RAM
Flash
Mac Address
Jumbo frame
Connectors
Network Cable
Optical Cable
IEEE802.3 10Base-T Ethernet
IEEE802.3u 100Base-TX
IEEE802.3ab 1000Base-T Ethernet
IEEE802.3z Gigabit fiber
IEEE802.3x Flow Control and Back Pressure
IEEE802.3ad Port trunk with LACP
IEEE802.1d Spanning Tree
IEEE802.1w Rapid Spanning Tree
IEEE802.1s Multiple Spanning Tree
IEEE802.3ad Link Aggregation Control Protocol
(LACP)
IEEE802.1AB Link Layer Discovery Protocol
(LLDP)
IEEE802.1X User Authentication (Radius)
IEEE802.1p Class of Service
IEEE802.1Q VLAN Tag
IEEE1588 Precision Time Protocol v2
IEEE802.3at/af Power over Ethernet
Back-plane (Switching Fabric): 24Gbps
14,880pps for Ethernet port
148,800pps for Fast Ethernet port
1,488,000pps for Gigabit Ethernet / Gigabit Fiber
port
Marvell 800Mhz
256M Byte
128M Byte
16K MAC address table
9KB on all ports
10/100/1000T: 8 x ports RJ-45 with Auto
MDI/MDI-X function
Mini-GBIC: 4 x 1000 SFP socket with DDM
RS-232 connector: RJ-45 type
Power & P-Fail connector: 1 x 6-pole terminal
block
DIDO : 1 x 6-pole terminal block
10Base-T: 2-pair UTP/STP Cat. 3, 4, 5/ 5E/ 6 cable
EIA/TIA-568 100-ohm (100m)
100Base-TX: 2-pair UTP/STP Cat. 5/ 5E/ 6 cable
EIA/TIA-568 100-ohm (100m)
1000Base-TX: 2-pair UTP/STP Cat. 5/ 5E/ 6 cable
EIA/TIA-568 100-ohm (100m)
1.25Gbps:
Multi mode: 0 to 550 m, 850 nm (50/125 μm); 0 to 2
km, 1310 nm (50/125 μm)
Single mode: 0 to 10 km/ 30 km/ 40 km, 1310 nm
(9/125 μm); 0 to 50 km/ 60 km/ 80km/ 120 km,
1550 nm (9/125 μm)
WDM 1.25Gbps:
Protocol
LED
DI/DO
Operating Humidity
Operating
Temperature
Storage
Temperature
Power Supply
PoE Budget
Single mode: 0 to 10 km/ 20 km/ 40 km/ 60 km,
1310 nm (9/125 μm); 0 to 80 km, 1490 nm (9/125
μm); 0 to 10 km/ 20 km/ 40 km/ 60 km/ 80 km,
1550 nm (9/125 μm)
CSMA/CD
Per unit: Power 1 (Green), Power 2 (Green), P-Fail
(Red)
Ethernet port: Link/Activity (Green), Speed
(Green); Mini-GBIC: Link/Activity (Green)
2 Digital Input (DI) :
Level 0: -30~2V / Level 1: 10~30V
Max. input current:8mA
2 Digital Output(DO): Open collector to 40 VDC,
200mA
5% ~ 95% (Non-condensing)
-20°C~60°C / -4°F~140°F (Standard model)
-40°C~75°C / -40°F~167°F(-E model)
-40°C~85°C / -40°F~185°F
Dual 45~57VDC (Standard model)
Dual 9.5~57VDC (12V model)
240W for 45~56V input
(55V input is recommended for 802.3at 30W
applications)
120W for 24V input
80W for 12V input
PoE pin
RJ-45 port # 1~#8 support IEEE 802.3at/af
assignment
End-point, Alternative A mode. Per port provides
30W at 54~56VDC/15W at 48V~56VDC.
Positive (VCC+): RJ-45 pin 1,2.
Power
Consumption
Case Dimension
Weight
Installation
EMI & EMS
Stability Testing
MTBF
Negative (VCC-): RJ-45 pin 3,6.
10W
Metal case. IP-30,
74 (W) x 105 (D) x 152 (H) mm (Standard model)
74 (W) x 135 (D) x 152 (H) mm (12V model)
900 g
DIN Rail and Wall Mount** Design
FCC Class A,
CE EN55022 Class A, CE EN55024, CE
EN61000-4-2, CE EN61000-4-3, CE EN61000-4-4,
CE EN61000-4-5, CE EN61000-4-6, CE
N61000-4-8, EN61000-4-11
IEC60068-2-32 (Free fall), IEC60068-2-27
(Shock),
IEC60068-2-6 (Vibration)
782,237 hours
Datasheet Version 2.0
www.lantechcom.tw | info@lantechcom.tw
5
Industrial PoE Managed Switches
Warranty
5 years
unauthorized intruder.
Software Specification
802.1X access control for port based and MAC
Management
SNMP v1 v2c, v3/ Web/Telnet/CLI
based authentication/MAC-Port binding
SNMP MIB
RFC 1215 Traps MIB,
RFC 1213 MIBII
RFC 1158 MIBII
RFC 1157 SNMP MIB,
RFC 1493 Bridge MIB,
RFC 1573 IF MIB
RFC 2674 VLAN MIB,
Partial RFC 1643 EtherLike,
Partial RFC 1757 RMON,
RFC 2674 Q-Bridge MIB; Bridge MIB,
RFC 2790 Host Resource MIB
LLDP MIB*
RSTP MIB*
Private MIB
ITU G.8032
Management access control with priority
256 Policy based Access Control List
SSL/ SSH for Management
HTTPS for secure access to the web interface
TACACS+ for Authentication
IGMP
Support IGMP snooping v1,v2,v3; Supports IGMP
static route; 256 multicast groups; IGMP router
port ; IGMP query; GMRP**
MVR
Static multicast forwarding forward reversed IGMP
flow (MVR) with multicast packets binding with
ports for IP surveillance application
Bandwidth Control
Support ingress packet filter and egress packet
limit.
The egress rate control supports all of packet type.
Ingress filter packet type combination rules are
Broadcast/Multicast/Flooded Unicast packet,
Broadcast/Multicast packet, Broadcast packet only
and all types of packet.
The packet filter rate can be set an accurate value
through the pull-down menu for the ingress packet
filter and the egress packet limit.
RTC
Built-in Real Time Clock to keep track of time
always
Supports Flow Control for Full-duplex and Back
Pressure for Half-duplex
Supports System log record and remote system
log server
Supports SMTP Server and 8 e-mail accounts for
receiving event alert; can send SMS text alert via
mobile
Provides one relay output for port breakdown,
power fail and alarm.
Alarm Relay current carry ability: 1A @ DC24V

Miss-wiring avoidance

Repowered auto ring restore

Loop protection
Support ITU G.8032 v2/2012 for Ring protection in
less than 20ms for self-heal recovery (basic mode)
Support various ring/chain topologies
Includes dynamic coupling ring & aggregation ring*
PoE Management
Per Port PoE
Status
PTP v2
User friendly UI
Port Trunk with
LACP
LLDP
CDP
Environmental
Monitoring**
VLAN
IPv6/4
Spanning Tree
Quality of Service
Enhanced G.8032 ring configuration with ease
Co-exist with RSTP on different ports
1.
PoE Detection to check if PD is hang up
then restart the PD
2.
PoE Scheduling to On/OFF PD upon
routine time table
On/ Off, voltage, current, watts, temperature
Support hardware-based IEEE1588 PTPv2 in 1μs,
End to End (2-step) and Peer to Peer (2-step)
modes in Transparent Clock, with 8 10/100/1000T

Auto topology drawing

Topology demo

Auto configuration for G.8032(auto mode)
for single ring

DDM threshold monitoring with dB
values***

Complete CLI for professional setting
trunk members
Aggregation ring for ring redundancy and
bandwidth combination*
Supports LLDP to allow switch to advise its
identification and capability on the LAN
Cisco Discovery Protocol for topology mapping
System status for input voltage, current and
ambient temperature to be shown in GUI and sent
alerting if any abnormal status(-M models)
Port Based VLAN
IEEE 802.1Q Tag VLAN (256 entries)/ VLAN ID
(Up to 4K, VLAN ID can be assigned from 1 to
4096.)
GVRP** (256 Groups)**, QinQ
Present
Supports IEEE802.1d Spanning Tree and
IEEE802.1w Rapid Spanning Tree, IEEE802.1s
Multiple Spanning Tree
The quality of service determined by port, Tag and
IPv4 Type of service, IPv4 Differentiated Services
Code Points - DSCP
Support IEEE802.1p class of service, per port
provides 8 priority queues
QoS by VLAN
IP Security
Tagged QoS by VLAN for all devices in the network
Supports 10 IP addresses that have permission to
access the switch management and to prevent
unauthorized intruder.
Supports IEEE802.1X Authentication/RADIUS
Network Security
System Log
SMTP/Text SMS
Relay Alarm
Protection
LACP Port Trunk: 8 Trunk groups/Maximum 8
Class of Service
Login Security
Port Mirror
Flow Control
Support 3 mirroring types: “RX, TX and Both
packet”
Support 10 IP addresses that have permission to
SNMP Trap
DHCP
Up to 10 trap stations; trap types including:

Device cold start

Authorization failure

Port link up/link down

DI/DO open/close

Typology change(ITU ring)

PoE ping failure

Power failure

Environmental abnormal**
Provide DHCP Client/ DHCP Server/DHCP Option
82/Port based&VLAN based DHCP distribution
(DHCP relay agent)
Mac based DHCP
Assign IP address by Mac that can include dumb
Server
DNS
switch in DHCP network
Provide DNS client feature and support Primary
and Secondary DNS server.
Supports SNTP to synchronize system clock in
Internet
Supports TFTP firmware update, TFTP backup
and restore; HTTP firmware upgrade; LantechTM
InstaConfig** for multiple upgrade
Supports text configuration file for system quick
installation; Support factory reset button to restore
all settings back to factory default
Each port allows an alphabetic string of 128-byte
assigned as its own unique name via the SNMP or
CLI interface
SNTP
Firmware Update
Configuration
upload and
download
IfAlias
*Future release
**Optional
***Optional DDM SFP required
access the switch management and to prevent
Datasheet Version 2.0
www.lantechcom.tw | info@lantechcom.tw
6
Industrial PoE Managed Switches
ORDERING INFOMATION

IPGS-3408GSFP…….………….….......P/N: 8350-611
8 10/100/1000T PoE at/af up to 30W + 4 1000M SFP L2+ Managed Industrial PoE Switch; -20°C to 60°C; Dual 48VDC

IPGS-3408GSFP-E…….……….….......P/N: 8350-612
8 10/100/1000T PoE at/af up to 30W + 4 1000M SFP L2+ Managed Industrial PoE Switch; -40°C to 75°C; Dual 48VDC

IPGS-3408GSFP-M…………….….......P/N: 8350-613
8 10/100/1000T PoE at/af up to 30W + 4 1000M SFP L2+ Managed Industrial PoE Switch w/Environmental monitoring; -20°C
to 60°C; Dual 48VDC

IPGS-3408GSFP-M-E………….….......P/N: 8350-614
8 10/100/1000T PoE at/af up to 30W + 4 1000M SFP L2+ Managed Industrial PoE Switch w/Environmental monitoring; -40°C
to 75°C; Dual 48VDC

IPGS-3408GSFP-12V…….…………...P/N: 8350-617
8 10/100/1000T PoE at/af up to 30W + 4 1000M SFP L2+ Managed Industrial PoE Switch; -20°C to 60°C; Dual 9.5~57VDC

IPGS-3408GSFP-12V-E…….………...P/N: 8350-618
8 10/100/1000T PoE at/af up to 30W + 4 1000M SFP L2+ Managed Industrial PoE Switch; -40°C to 75°C; Dual 9.5~57VDC

IPGS-3408GSFP-12V-M……………....P/N: 8350-6171
8 10/100/1000T PoE at/af up to 30W + 4 1000M SFP L2+ Managed Industrial PoE Switch w/Environmental monitoring; -20°C
to 60°C; Dual 9.5~57VDC

IPGS-3408GSFP-12V-M-E…………....P/N: 8350-6181
8 10/100/1000T PoE at/af up to 30W + 4 1000M SFP L2+ Managed Industrial PoE Switch w/Environmental monitoring; -40°C
to 75°C; Dual 9.5~57VDC
OPTIONAL ACCESSORIES
55VDC DIN Rail Power for 802.3at Applications
 AD1240-48S-5
48~56VDC, 4.3A, Wide AC Input, Build-in fan Cooled, DIN Rail or Wall Mounted, RoHS, Operating Temp. -20°C~50°C
(ambient, derating each output at 2.5% per degree from 50°C ~ 70°C)
 AD1360-48S-5
48~56VDC, 6.5A, Wide AC Input, Build-in fan Cooled, DIN Rail or Wall Mounted, RoHS, Operating Temp. -20°C~50°C
(ambient, derating each output at 2.5% per degree from 50°C ~ 70°C)
 AD1500-48S-5
48~56VDC, 9A, Wide AC Input, Build-in fan Cooled, DIN Rail or Wall Mounted, RoHS, Operating Temp. -20°C~50°C
(ambient, derating each output at 2.5% per degree from 50°C ~ 70°C)
Mini GBIC (SFP)
 8330-162X
 8330-163X
 8330-165X
 8340-0591
 8330-166
MINI GBIC 1000SX (LC/0.5km) Transceiver
MINI GBIC 1000SX2 (LC/2km) Transceiver
MINI GBIC 1000LX (LC/10km) Transceiver
MINI GBIC 1000LHX (LC/40km) Transceiver
MINI GBIC 1000XD (LC/50km) Transceiver
 8330-169
 8330-167
 8330-170
 8330-168
MINI GBIC 1000XD (LC/60km) Transceiver
MINI GBIC 1000ZX (LC/80km) Transceiver
MINI GBIC 1000EZX (120km) Transceiver
MINI GBIC 10/100/1000T (100m) Transceiver
Wall Mount Bracket
MBEAR001
Wall mount bracket for 96.3(W) x 114.3 (D) x 152 (H) mm Industrial switches
Lantech Communications Global Inc.
www.lantechcom.tw
info@lantechcom.tw
© 2016 Copyright Lantech Communications Global Inc. all rights reserved.
The revise authority rights of product specifications belong to Lantech Communications Global Inc.
Lantech may make changes to specification and product descriptions at anytime, without notice.
Datasheet Version 2.0
www.lantechcom.tw | info@lantechcom.tw
Download PDF
Similar pages